EDUS391000 - F12
FXTQ-PA
Air Handling Unit
AMERICAS
EDUS391000-F12
FXTQ-PA
Air Handling Unit
1.
2.
3.
4.
5.
Specifications ..............................................................................................2
Dimensions .................................................................................................4
Piping Diagrams..........................................................................................6
Wiring Diagrams..........................................................................................7
Electric Characteristics................................................................................8
5.1 Indoor Unit.................................................................................................... 8
5.2 Electric Heater.............................................................................................. 9
6. Capacity Tables ........................................................................................10
6.1 Cooling Capacity ........................................................................................ 10
6.2 Heating Capacity ........................................................................................ 11
7. Airflow Auto Adjustment Characteristics ...................................................12
8. Installation .................................................................................................14
9. Accessories...............................................................................................31
FXTQ-PA
1
Specifications
EDUS391000-F12
1. Specifications
Air Handling Unit
Model
FXTQ12PAVJU
FXTQ18PAVJU
Power Supply
FXTQ24PAVJU
1, 3 Cooling capacity
Btu/h
12,000
18,000
24,000
2, 3 Heating capacity
Btu/h
13,500
20,000
27,000
Dimensions: (H×W×D)
in (mm)
6 × 14 × 15
ft² (m²)
Model
4 × 22 × 15
3.30 (1)
6.02 (1.8)
ECM (1/2HP)
ECM (3/4HP)
Type
Sirocco fan
Motor output
HP
Airflow rate (H/L)
CFM
External static
pressure
“Wg
3/4
1/2
400/280
600/420
Direct drive
— 4
Weight
lbs (kg)
121 (55)
149 (67.6)
Liquid
in (mm)
1/4 (6.4) (Brazed)
3/8 (9.5) (Brazed)
Gas
in (mm)
1/2 (12.7) (Brazed)
Drain
in (mm)
Safety devices
Refrigerant control
Connectable outdoor unit
Drawing No.
1,000/700
Microprocessor thermostat for cooling and heating
Air filter
Standard accessories
800/560
Up to 0.5
Drive
Temperature control
Piping connections
34,000
(1353 x 559 x 609)
Cross fin coil
Rows×Stages×FPI
Face area
Fan
30,000
53-1/4 × 22 × 24
46-3/4 × 19-1/2 × 22 (1187 x 495 x 559)
Type
Coil
FXTQ30PAVJU
1 phase, 208/230V, 60Hz
5/8 (15.8) (Brazed)
3/4 (19.1) 5
Fuse,
Fan driver overload protector
Electronic expansion valve
R-410A VRV Series
Operation manual, Installation manual
C: 3D068193
Notes:





2
1 Nominal cooling capacities are based on the following conditions:
Return air temperature: 80°FDB(27°CDB), 67°FWB(19.4°CWB)
Outdoor temperature: 95°FDB (35°C)
Equivalent ref. piping: 25ft (7.5 m) (Horizontal)
2 Nominal heating capacities are based on the following conditions:
Return air temperature: 70°FDB (21°C)
Outdoor temperature: 47°FDB (8.3°CDB) , 43°FWB (6.1°CWB)
Equivalent ref. piping: 25ft (7.5 m) (Horizontal)
1 and 2 are the performance for vertical installation.
For horizontal installation, capacity could decrease by about 10%.
3 Capacities are net, including a deduction for cooling (an addition for heating) for indoor fan motor heat.
4 Air filter is not standard accessory, but please mount it in the duct system of the suction side.
5 A field-supplied secondary drain pan may be required.
FXTQ-PA
EDUS391000-F12
Specifications
Air Handling Unit
Model
FXTQ36PAVJU
Power Supply
FXTQ42PAVJU
FXTQ48PAVJU
FXTQ54PAVJU
1 phase, 208/230V, 60Hz
1, 3 Cooling capacity
Btu/h
36,000
42,000
48,000
54,000
2, 3 Heating capacity
Btu/h
40,000
47,000
54,000
60,000
Dimensions: (H×W×D)
in (mm)
53-1/4 × 22 × 24 (1353 x 559 x 610)
Type
Coil
Cross fin coil
Rows×Stages×FPI
Face area
4 × 22 × 15
8 × 22 × 15
ft² (m²)
6.02 (1.8)
Model
ECM(3/4HP)
Type
Sirocco fan
Motor output
Fan
HP
Airflow rate (H/L)
CFM
External static
pressure
“Wg
3/4
1,200/840
Drive
Direct drive
— 4
Air filter
lbs (kg)
149 (67.6)
169 (76.7)
Liquid
in (mm)
3/8 (9.5) (Brazed)
Gas
in (mm)
5/8 (15.8) (Brazed)
Drain
in (mm)
3/4 (19.1) 5
Safety devices
Refrigerant control
Connectable outdoor unit
Drawing No.
1,800/1,260
Microprocessor thermostat for cooling and heating
Weight
Standard accessories
1,600/1,120
Up to 0.5
Temperature control
Piping connections
1,400/980
Fuse,
Fan driver overload protector
Electronic expansion valve
R-410A VRV Series
Operation manual, Installation manual
C: 3D068193
Notes:





1 Nominal cooling capacities are based on the following conditions:
Return air temperature: 80°FDB(27°CDB), 67°FWB(19.4°CWB)
Outdoor temperature: 95°FDB (35°CDB)
Equivalent ref. piping: 25ft (7.5 m) (Horizontal)
2 Nominal heating capacities are based on the following conditions:
Return air temperature: 70°FDB (21°CDB)
Outdoor temperature: 47°FDB (8.3°CDB) , 43°FWB (6.1°CWB)
Equivalent ref. piping: 25ft (7.5 m) (Horizontal)
1 and 2 are the performance for vertical installation.
For horizontal installation, capacity could decrease by about 10%.
3 Capacities are net, including a deduction for cooling (an addition for heating) for indoor fan motor heat.
4 Air filter is not standard accessory, but please mount it in the duct system of the suction side.
5 A field-supplied secondary drain pan may be required.
FXTQ-PA
3
Dimensions
EDUS391000-F12
2. Dimensions
3D068376A
FXTQ12PAVJU
FXTQ18PAVJU
4
FXTQ-PA
EDUS391000-F12
Dimensions
3D068377A
FXTQ24PAVJU
FXTQ30PAVJU
FXTQ36PAVJU
FXTQ42PAVJU
FXTQ48PAVJU
FXTQ54PAVJU
FXTQ-PA
5
Piping Diagrams
EDUS391000-F12
3. Piping Diagrams
C: 4D068194
6
Model
GAS
Liquid
FXTQ12/18PAVJU
1/2
1/4
FXTQ24/30/36/42/48/54PAVJU
5/8
3/8
FXTQ-PA
EDUS391000-F12
Wiring Diagrams
4. Wiring Diagrams
FXTQ12PAVJU / FXTQ18PAVJU / FXTQ24PAVJU / FXTQ30PAVJU / FXTQ36PAVJU / FXTQ42PAVJU /
FXTQ48PAVJU / FXTQ54PAVJU
PROTECTIVE GROUND
NOISELESS GROUND
3D065036F
NOTE:
This unit is not equipped with a return air sensor. A remote sensor is required when not
using a BRC1E71 Controller or if this controller is not positioned to sense space temperature.
FXTQ-PA
7
Electric Characteristics
EDUS391000-F12
5. Electric Characteristics
5.1
Indoor Unit
Symbols:
MCA
MOP
IFM
HP
FLA
:
:
:
:
:
Minimum Circuit Amps (A)
Maximum Overcurrent Protective Device (A)
Indoor Fan Motor
Fan Motor Rater Output (HP)
Full Load Amps (A)
NOTE:
1. Voltage range:
Units are suitable for use on electrical systems where voltage supplied
to unit terminals is not below or above listed range limits.
2. Maximum allowable voltage imbalance between phases is 2%.
3. Select wire size based on the MCA.
8
C: 4D068256
FXTQ-PA
EDUS391000-F12
5.2
Electric Characteristics
Electric Heater
4D068258
FXTQ-PA
9
Capacity Tables
EDUS391000-F12
6. Capacity Tables
6.1
Cooling Capacity
FXTQ-PA
Outdoor
Unit size air temp.
12
18
24
30
36
42
48
54
TC:
SHC:
10
°FDB
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
75
79
83
87
91
95
99
103
[Cooling capacity]
61.0 °FWB
TC
SHC
MBh MBh
9.5
7.0
9.5
7.0
9.5
7.0
9.5
7.0
9.5
7.0
9.5
7.0
9.5
7.0
9.5
7.0
14.2 11.3
14.2 11.3
14.2 11.3
14.2 11.3
14.2 11.3
14.2 11.3
14.2 11.3
14.2 11.3
19.0 15.0
19.0 15.0
19.0 15.0
19.0 15.0
19.0 15.0
19.0 15.0
19.0 15.0
19.0 15.0
23.7 18.7
23.7 18.7
23.7 18.7
23.7 18.7
23.7 18.7
23.7 18.7
23.7 18.7
23.7 18.7
28.4 22.6
28.4 22.6
28.4 22.6
28.4 22.6
28.4 22.6
28.4 22.6
28.4 22.6
28.4 22.6
33.2 25.6
33.2 25.6
33.2 25.6
33.2 25.6
33.2 25.6
33.2 25.6
33.2 25.6
33.2 25.6
37.9 29.0
37.9 29.0
37.9 29.0
37.9 29.0
37.9 29.0
37.9 29.0
37.9 29.0
37.9 29.0
42.6 33.0
42.6 33.0
42.6 33.0
42.6 33.0
42.6 33.0
42.6 33.0
42.6 33.0
42.6 33.0
64.0 °FWB
TC
SHC
MBh MBh
10.7
7.5
10.7
7.5
10.7
7.5
10.7
7.5
10.7
7.5
10.7
7.5
10.7
7.5
10.7
7.5
16.1 12.0
16.1 12.0
16.1 12.0
16.1 12.0
16.1 12.0
16.1 12.0
16.1 12.0
16.1 12.0
21.5 15.9
21.5 15.9
21.5 15.9
21.5 15.9
21.5 15.9
21.5 15.9
21.5 15.9
21.5 15.9
26.8 20.0
26.8 20.0
26.8 20.0
26.8 20.0
26.8 20.0
26.8 20.0
26.8 20.0
26.8 20.0
32.2 24.3
32.2 24.3
32.2 24.3
32.2 24.3
32.2 24.3
32.2 24.3
32.2 24.3
32.2 24.3
37.6 27.4
37.6 27.4
37.6 27.4
37.6 27.4
37.6 27.4
37.6 27.4
37.6 27.4
37.6 27.4
43.0 31.1
43.0 31.1
43.0 31.1
43.0 31.1
43.0 31.1
43.0 31.1
43.0 31.1
43.0 31.1
48.3 35.4
48.3 35.4
48.3 35.4
48.3 35.4
48.3 35.4
48.3 35.4
48.3 35.4
48.3 35.4
Indoor air temp.
67.0 °FWB
70.0 °FWB
TC
SHC
TC
SHC
MBh MBh MBh MBh
12.0
8.0
13.3
8.5
12.0
8.0
13.1
8.5
12.0
8.0
12.9
8.5
12.0
8.0
12.6
8.5
12.0
8.0
12.5
8.5
12.0
8.0
12.2
8.3
11.8
7.9
12.0
8.2
11.6
7.8
11.8
8.1
18.0 12.6 19.9 13.3
18.0 12.6 19.7 13.3
18.0 12.6 19.3 13.3
18.0 12.6 18.9 13.3
18.0 12.6 18.7 13.3
18.0 12.6 18.4 13.0
17.7 12.6 18.0 12.8
17.3 12.5 17.7 12.7
24.0 16.9 26.5 17.8
24.0 16.9 26.3 17.8
24.0 16.9 25.8 17.8
24.0 16.9 25.3 17.8
24.0 16.9 24.9 17.6
24.0 16.9 24.5 17.2
23.6 16.9 24.1 17.0
23.1 16.7 23.6 16.8
30.0 21.4 33.1 22.7
30.0 21.4 32.8 22.7
30.0 21.4 32.2 22.7
30.0 21.4 31.6 22.7
30.0 21.4 31.1 22.4
30.0 21.4 30.6 21.9
29.5 21.1 30.1 21.7
28.9 20.9 29.5 21.4
36.0 26.0 39.8 27.7
36.0 26.0 39.4 27.7
36.0 26.0 38.6 27.7
36.0 26.0 37.9 27.7
36.0 26.0 37.4 27.7
36.0 26.0 36.7 27.1
35.4 25.7 36.1 26.8
34.7 25.4 35.4 26.5
42.0 29.3 46.4 31.2
42.0 29.3 45.9 31.2
42.0 29.3 45.1 31.2
42.0 29.3 44.2 31.1
42.0 29.3 43.6 30.8
42.0 29.3 42.8 30.1
41.3 29.0 42.1 29.8
40.5 28.7 41.3 29.5
48.0 33.2 53.0 35.3
48.0 33.2 52.5 35.3
48.0 33.2 51.5 35.3
48.0 33.2 50.5 35.2
48.0 33.2 49.8 34.9
48.0 33.2 49.0 34.1
47.2 32.9 48.1 33.8
46.3 32.5 47.2 33.4
54.0 37.8 59.6 40.2
54.0 37.8 59.1 40.2
54.0 37.8 57.9 40.2
54.0 37.8 56.8 40.1
54.0 37.8 56.0 39.7
54.0 37.8 55.1 38.9
53.0 37.4 54.1 38.5
52.0 37.0 53.1 38.1
72.0 °FWB
TC
SHC
MBh MBh
13.5
8.1
13.3
8.0
13.0
8.0
12.9
7.9
12.6
7.7
12.4
7.6
12.2
7.5
12.0
7.4
20.3 13.7
19.9 13.6
19.5 13.4
19.3 13.2
18.9 13.0
18.6 12.8
18.3 12.6
17.9 12.4
27.0 26.1
26.5 25.8
26.0 25.5
25.8 25.1
25.3 24.7
24.8 24.3
24.4 23.9
23.9 23.4
33.8 25.7
33.1 25.4
32.5 25.0
32.2 24.7
31.6 24.3
31.0 23.9
30.4 23.5
29.9 23.0
40.5 26.7
39.8 26.4
39.0 26.1
38.6 25.8
37.9 25.4
37.2 25.0
36.5 24.6
35.9 24.2
47.3 30.0
46.4 29.7
45.5 29.4
45.1 29.1
44.2 28.7
43.4 28.3
42.6 27.9
41.9 27.5
54.0 34.0
53.0 33.7
52.0 33.3
51.5 32.9
50.5 32.5
49.6 32.1
48.7 31.6
47.9 31.1
60.8 38.7
59.6 38.3
58.5 37.9
57.9 37.5
56.8 37.0
55.8 36.5
54.8 36.0
53.8 35.4
75.0 °FWB
TC
SHC
MBh MBh
13.8
8.1
13.5
8.0
13.3
7.9
13.1
7.8
12.9
7.7
12.6
7.6
12.4
7.5
12.2
7.4
20.6 11.8
20.3 11.6
19.9 11.3
19.7 11.1
19.3 10.9
18.9 10.6
18.6 10.4
18.3 10.1
27.5 26.1
27.0 25.8
26.5 25.5
26.3 25.1
25.8 24.8
25.3 24.3
24.8 23.9
24.4 23.4
34.4 25.7
33.8 25.4
33.1 25.0
32.8 24.7
32.2 24.3
31.6 23.9
31.0 23.5
30.5 23.0
41.3 26.7
40.5 26.4
39.8 26.1
39.4 25.8
38.6 25.4
37.9 25.0
37.2 24.6
36.6 24.2
48.1 29.1
47.3 28.7
46.4 28.4
45.9 28.0
45.1 27.6
44.2 27.2
43.4 26.7
42.7 26.3
55.0 33.0
54.0 32.6
53.0 32.2
52.5 31.7
51.5 31.3
50.5 30.8
49.7 30.3
48.8 29.8
61.9 37.5
60.8 37.1
59.6 36.6
59.1 36.1
57.9 35.6
56.8 35.0
55.9 34.5
54.9 33.9
Total capacity ; MBh
Sensible heat capacity ; MBh
FXTQ-PA
EDUS391000-F12
6.2
Capacity Tables
Heating Capacity
FXTQ-PA
Unit size
12
18
24
30
36
42
48
[Heating capacity]
Outdoor
air temp.
°FDB
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
FXTQ-PA
°FWB
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
62.0°FDB
TC
MBh
12.0
12.8
13.5
14.3
15.1
15.8
15.8
15.8
15.8
15.8
15.8
17.8
18.9
20.0
21.1
22.4
23.3
23.3
23.3
23.3
23.3
23.3
24.1
25.5
27.0
28.5
30.3
31.5
31.5
31.5
31.5
31.5
31.5
30.3
32.1
34.0
35.9
38.1
39.7
39.7
39.7
39.7
39.7
39.7
35.7
37.8
40.0
42.2
44.8
46.7
46.7
46.7
46.7
46.7
46.7
41.9
44.4
47.0
49.6
52.7
54.8
54.8
54.8
54.8
54.8
54.8
48.2
51.0
54.0
57.0
60.5
63.0
63.0
63.0
63.0
63.0
63.0
65.0 °FDB
TC
MBh
12.0
12.8
13.5
14.3
14.8
14.8
14.8
14.8
14.8
14.8
14.8
17.8
18.9
20.0
21.1
21.9
21.9
21.9
21.9
21.9
21.9
21.9
24.0
25.5
27.0
28.5
29.5
29.5
29.5
29.5
29.5
29.5
29.5
30.3
32.1
34.0
35.9
37.1
37.1
37.1
37.1
37.1
37.1
37.1
35.6
37.8
40.0
42.2
43.7
43.7
43.7
43.7
43.7
43.7
43.7
41.8
44.4
47.0
49.6
51.4
51.4
51.4
51.4
51.4
51.4
51.4
48.1
51.0
54.0
57.0
59.0
59.0
59.0
59.0
59.0
59.0
59.0
Indoor air temp.
68.0 °FDB 70.0 °FDB
TC
TC
MBh
MBh
12.0
12.0
12.6
12.6
13.4
13.4
14.0
13.5
14.0
13.5
14.0
13.5
13.5
14.0
14.0
13.5
14.0
13.5
14.0
13.5
14.0
13.5
17.8
17.7
18.7
18.7
19.8
19.8
20.7
20.0
20.7
20.0
20.7
20.0
20.0
20.7
20.7
20.0
20.7
20.0
20.7
20.0
20.7
20.0
24.0
24.0
25.3
25.3
26.8
26.8
28.0
27.0
28.0
27.0
28.0
27.0
27.0
28.0
28.0
27.0
28.0
27.0
28.0
27.0
28.0
27.0
30.2
30.2
31.8
31.8
33.7
33.7
35.3
34.0
35.3
34.0
35.3
34.0
34.0
35.3
35.3
34.0
35.3
34.0
35.3
34.0
35.3
34.0
35.5
35.5
37.4
37.4
39.6
39.6
41.5
40.0
41.5
40.0
41.5
40.0
40.0
41.5
41.5
40.0
41.5
40.0
41.5
40.0
41.5
40.0
41.7
41.7
44.0
44.0
46.6
46.6
48.7
47.0
48.7
47.0
48.7
47.0
47.0
48.7
48.7
47.0
48.7
47.0
48.7
47.0
48.7
47.0
48.0
47.9
50.5
50.5
53.5
53.5
56.0
54.0
56.0
54.0
56.0
54.0
54.0
56.0
56.0
54.0
56.0
54.0
56.0
54.0
56.0
54.0
72.0 °FDB
TC
MBh
12.0
12.6
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
13.0
17.7
18.7
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
19.3
23.9
25.3
26.0
26.0
26.0
26.0
26.0
26.0
26.0
26.0
26.0
30.1
31.8
32.7
32.7
32.7
32.7
32.7
32.7
32.7
32.7
32.7
35.4
37.4
38.5
38.5
38.5
38.5
38.5
38.5
38.5
38.5
38.5
41.6
44.0
45.3
45.3
45.3
45.3
45.3
45.3
45.3
45.3
45.3
47.9
50.5
52.0
52.0
52.0
52.0
52.0
52.0
52.0
52.0
52.0
75.0 °FDB
TC
MBh
11.9
12.3
12.3
12.3
12.3
12.3
12.3
12.3
12.3
12.3
12.3
17.7
18.1
18.1
18.1
18.1
18.1
18.1
18.1
18.1
18.1
18.1
23.9
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
30.1
30.9
30.9
30.9
30.9
30.9
30.9
30.9
30.9
30.9
30.9
35.4
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
36.3
41.6
42.6
42.6
42.6
42.6
42.6
42.6
42.6
42.6
42.6
42.6
47.8
49.0
49.0
49.0
49.0
49.0
49.0
49.0
49.0
49.0
49.0
Unit size
54
TC:
Outdoor
air temp.
°FDB
22.0
26.0
30.0
35.0
39.0
44.0
47.0
51.0
54.0
57.0
60.0
°FWB
20.0
24.0
28.0
32.0
36.0
40.0
43.0
47.0
50.0
53.0
56.0
62.0°FDB
TC
MBh
53.5
56.7
60.0
63.3
67.2
70.0
70.0
70.0
70.0
70.0
70.0
65.0 °FDB
TC
MBh
53.4
56.7
60.0
63.3
65.6
65.6
65.6
65.6
65.6
65.6
65.6
Indoor air temp.
68.0 °FDB 70.0 °FDB
TC
TC
MBh
MBh
53.3
53.2
56.1
56.1
59.4
59.4
62.2
60.0
62.2
60.0
62.2
60.0
62.2
60.0
62.2
60.0
62.2
60.0
62.2
60.0
62.2
60.0
72.0 °FDB
TC
MBh
53.2
56.1
57.8
57.8
57.8
57.8
57.8
57.8
57.8
57.8
57.8
75.0 °FDB
TC
MBh
53.1
54.4
54.4
54.4
54.4
54.4
54.4
54.4
54.4
54.4
54.4
Total capacity ; MBh
11
Airflow Auto Adjustment Characteristics
EDUS391000-F12
7. Airflow Auto Adjustment Characteristics
FXTQ12PAVJU
FXTQ18PAVJU
3D068210
3D068211
Notes:
1. If the airflow is less than 10% of the rated air volume, it is automatically adjusted to the rated volume.
2. The unit automatically adjusts external static pressure between 0.0 in.W.C. - 0.5 in.W.C (When fan speed is "H").
3. Airflow cannot operate at the rated value if it is outside the ESP range in the above graph.
4. This figure shows a fan characteristics at "H" speed and "L" speed.
5. Fan speed is changeable by using the remote controller.
6. ESP: external static pressure.
12
FXTQ-PA
EDUS391000-F12
Airflow Auto Adjustment Characteristics
FXTQ24PAVJU
FXTQ30PAVJU
3D068212
FXTQ42PAVJU
FXTQ36PAVJU
3D068213
FXTQ48PAVJU
3D068215
3D068214
FXTQ54PAVJU
3D068216
3D068217
Notes:
1. If the airflow is less than 10% of the rated air volume, it is automatically adjusted to the rated volume.
2. The unit automatically adjusts external static pressure between 0.0 in.W.C. - 0.5 in.W.C (When fan speed is "H").
3. Airflow cannot operate at the rated value if it is outside the ESP range in the above graph.
4. This figure shows a fan characteristics at "H" speed and "L" speed.
5. Fan speed is changeable by using the remote controller.
6. ESP: external static pressure.
FXTQ-PA
13
Installation
EDUS391000-F12
8. Installation
Read these SAFETY CONSIDERATIONS for Installation carefully
before installing an air conditioner or heat pump. After completing
the installation, make sure that the unit operates properly during the
startup operation.
Instruct the customer on how to operate and maintain the unit.
Inform customers that they should store this Installation Manual with
the Operation Manual for future reference.
Always use a licensed installer or contractor to install this product.
Improper installation can result in water or refrigerant leakage,
electrical shock, fire, or explosion.
Meanings of DANGER, WARNING, CAUTION, and NOTE
Symbols:
DANGER .............. Indicates an imminently hazardous
situation which, if not avoided, will
result in death or serious injury.
WARNING ............ Indicates a potentially hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION ............. Indicates a potentially hazardous
situation which, if not avoided, may
result in minor or moderate injury. It
may also be used to alert against
unsafe practices.
NOTE .................. Indicates situations that may result
in equipment or property-damage
accidents only.
DANGER
• Refrigerant gas is heavier than air and replaces oxygen. A massive leak can lead to oxygen depletion,
especially in basements, and an asphyxiation hazard
could occur leading to serious injury or death.
• Do not ground units to water pipes, gas pipes,
telephone wires, or lightning rods as incomplete
grounding can cause a severe shock hazard
resulting in severe injury or death. Additionally,
grounding to gas pipes could cause a gas leak and
potential explosion causing severe injury or death.
• If refrigerant gas leaks during installation, ventilate
the area immediately. Refrigerant gas may produce
toxic gas if it comes into contact with fire. Exposure
to this gas could cause severe injury or death.
• After completing the installation work, check that the
refrigerant gas does not leak throughout the system.
• Do not install unit in an area where flammable
materials are present due to risk of explosions that
can cause serious injury or death.
• Safely dispose all packing and transportation
materials in accordance with federal/state/local laws
or ordinances. Packing materials such as nails and
other metal or wood parts, including plastic packing
materials used for transportation may cause injuries
or death by suffocation.
• Only qualified personnel must carry out the
installation work. Installation must be done in
accordance with this installation manual. Improper
14
installation may result in water leakage, electric
shock, or fire.
• When installing the unit in a small room, take measures
to keep the refrigerant concentration from exceeding
allowable safety limits. Excessive refrigerant leaks, in
the event of an accident in a closed ambient space, can
lead to oxygen deficiency.
• Use only specified accessories and parts for
installation work. Failure to use specified parts may
result in water leakage, electric shocks, fire, or the
unit falling.
• Install the air conditioner or heat pump on a
foundation strong enough that it can withstand the
weight of the unit. A foundation of insufficient
strength may result in the unit falling and causing
injuries.
• Take into account strong winds, typhoons, or
earthquakes when installing. Improper installation
may result in the unit falling and causing accidents.
• Make sure that a separate power supply circuit is
provided for this unit and that all electrical work is
carried out by qualified personnel according to local.
state, and national regulations. An insufficient power
supply capacity or improper electrical construction
may lead to electric shocks or fire.
• Make sure that all wiring is secured, that specified
wires are used, and that no external forces act on the
terminal connections or wires. Improper
connections or installation may result in fire.
• When wiring, position the wires so that the terminal
box lid can be securely fastened. Improper
positioning of the terminal box lid may result in
electric shocks, fire, or the terminals overheating.
• Before touching electrical parts, turn off the unit.
• It is recommended to install a ground fault circuit
interrupter if one is not already available. This helps
prevent electrical shocks or fire.
• Securely fasten the outside unit terminal cover
(panel). If the terminal cover/panel is not installed
properly, dust or water may enter the outside unit
causing fire or electric shock.
• When installing or relocating the system, keep the
refrigerant circuit free from substances other than
the specified refrigerant (R-410A) such as air. Any
presence of air or other foreign substance in the
refrigerant circuit can cause an abnormal pressure
rise or rupture, resulting in injury.
• Do not change the setting of the protection devices.
If the pressure switch, thermal switch, or other
protection device is shorted and operated forcibly, or
FXTQ-PA
EDUS391000-F12
parts other than those specified by Daikin are used,
fire or explosion may occur.
CAUTION
• Do not touch the switch with wet fingers. Touching a
switch with wet fingers can cause electric shock.
• Do not allow children to play on or around the unit to
prevent injury.
• Do not touch the refrigerant pipes during and
immediately after operation as the refrigerant pipes
may be hot or cold, depending on the condition of
the refrigerant flowing through the refrigerant
piping, compressor, and other refrigerant cycle
parts. Your hands may suffer burns or frostbite if you
touch the refrigerant pipes. To avoid injury, give the
pipes time to return to normal temperature or, if you
must touch them, be sure to wear proper gloves.
• Install drain piping to proper drainage. Improper
drain piping may result in water leakage and
property damage.
• Insulate piping to prevent condensation.
• Be careful when transporting the product.
• Do not turn off the power immediately after stopping
operation. Always wait for at least 5 minutes before
turning off the power. Otherwise, water leakage may
occur.
• Do not use a charging cylinder. Using a charging
cylinder may cause the refrigerant to deteriorate.
• Refrigerant R-410A in the system must be kept clean,
dry, and tight.
(a) Clean and Dry -- Foreign materials (including
mineral oils such as SUNISO oil or moisture)
should be prevented from getting into the
system.
(b) Tight -- R-410A does not contain any chlorine,
does not destroy the ozone layer, and does not
reduce the earth’s protection again harmful
ultraviolet radiation. R-410A can contribute to
the greenhouse effect if it is released. Therefore
take proper measures to check for the tightness
of the refrigerant piping installation. Read the
chapter Refrigerant Piping and follow the
procedures.
• Since R-410A is a blend, the required additional
refrigerant must be charged in its liquid state. If the
refrigerant is charged in a state of gas, its
composition can change and the system will not
work properly.
• The indoor unit is for R-410A. See the catalog for
indoor models that can be connected. Normal
FXTQ-PA
Installation
operation is not possible when connected to other
units.
• Remote controller (wireless kit) transmitting
distance can be shorter than expected in rooms with
electronic fluorescent lamps (inverter or rapid start
types). Install the indoor unit far away from
fluorescent lamps as much as possible.
• Indoor units are for indoor installation only. Outdoor
units can be installed either outdoors or indoors.
This unit is for indoor use.
• Do not install the air conditioner or heat pump in the
following locations:
(a) Where a mineral oil mist or oil spray or vapor is
produced, for example, in a kitchen.
Plastic parts may deteriorate and fall off or result in
water leakage.
(b) Where corrosive gas, such as sulfurous acid gas, is
produced.
Corroding copper pipes or soldered parts may
result in refrigerant leakage.
(c) Near machinery emitting electromagnetic waves.
Electromagnetic waves may disturb the operation
of the control system and cause the unit to
malfunction.
(d) Where flammable gas may leak, where there is
carbon fiber, or ignitable dust suspension in the air,
or where volatile flammables such as thinner or
gasoline are handled. Operating the unit in such
conditions can cause a fire.
• Take adequate measures to prevent the outside unit
from being used as a shelter by small animals. Small
animals making contact with electrical parts can
cause malfunctions, smoke, or fire. Instruct the
customer to keep the area around the unit clean.
NOTE
• Install the power supply and control wires for the indoor
and outdoor units at least 3.5 feet away from televisions or
radios to prevent image interference or noise. Depending
on the radio waves, a distance of 3.5 feet may not be sufficient to eliminate the noise.
• Dismantling the unit, treatment of the refrigerant, oil
and additional parts must be done in accordance with
the relevant local, state, and national regulations.
• Do not use the following tools that are used with
conventional refrigerants: gauge manifold, charge
hose, gas leak detector, reverse flow check valve,
refrigerant charge base, vacuum gauge, or refrigerant
recovery equipment.
• If the conventional refrigerant and refrigerator oil are
mixed in R-410A, the refrigerant may deteriorate.
• This air conditioner or heat pump is an appliance that
should not be accessible to the general public.
• As design pressure is 478 psi, the wall thickness of
field-installed pipes should be selected in accordance
with the relevant local, state, and national regulations.
15
Installation
2.
EDUS391000-F12
FOR THE FOLLOWING ITEMS, TAKE SPECIAL CARE
DURING CONSTRUCTION AND CHECK AFTER
INSTALLATION IS FINISHED.
BEFORE INSTALLATION
WARNING
• Entrust installation to the place of purchase or a qualified
serviceman. Improper installation could lead to leaks and, in
worse cases, electric shock or fire.
• Use of unspecified parts could lead to the unit falling, leaks
and, in worse cases, electric shock or fire.
NOTE
• Be sure to read this manual before installing the indoor unit.
• Be sure to mount an air filter (part to be procured in the
field) in the suction air passage in order to prevent water
leaking, etc.
The accessories needed for installation must be retained
in your custody until the installation work is completed.
Do not discard them.
1. Decide upon a line of transport.
2. Leave the unit inside its packaging while moving, until
reaching the installation site. Where unpacking is unavoidable, use a sling of soft material or protective plates together with a rope when lifting, to avoid damage or scratches to
the unit.
Be sure to check the type of R410A refrigerant to be used
before installing the unit.
(Using an incorrect refrigerant will prevent normal operation of the unit.)
For the installation of an outdoor unit, refer to the installation
manual attached to the outdoor unit.
2-1 PRECAUTIONS
• Be sure to instruct customers how to properly operate the
unit (operating different functions, and adjusting the temperature) by having them carry out operations themselves
while looking at the operation manual.
• Do not install in locations where the air contains high levels of
salt such as that near the ocean and where voltage fluctuates
greatly such as that in factories, or in vehicles or vessels.
2-2 ACCESSORIES
Check the following accessories are included with your unit.
Name
Clamp
material (1)
Insulation tube
4 pcs.
1 set
Quantity
Shape
Large (3)
2 pcs.
2-3 OPTIONAL ACCESSORIES
• This indoor unit requires one of the operation remote controls listed below.
Remote controller
Wired type
Wireless type
3
If not properly done, what is
likely to occur
Are the indoor and outdoor
The units may drop, vibrate
units fixed firmly?
or make noise.
Is the refrigerant leak test
It may result in insufficient
finished?
cooling.
Is the unit fully insulated?
Condensate may drip.
Does drainage flow smoothly? Condensate may drip.
Does the power supply
The unit may malfunction or
voltage correspond to that
the components burn out.
shown on the name plate?
Are wiring and piping
The unit may malfunction or
correct?
the components burn out.
Incomplete grounding may
Is the unit safely grounded?
result in electric shocks.
Is wiring size according to
The unit may malfunction or
specifications?
the components burn out.
Is something blocking the air
It may result in insufficient
outlet or inlet of either the
cooling.
indoor or outdoor units?
Are refrigerant piping length
The refrigerant charge in
and additional refrigerant
the system is not clear.
charge noted down?
Items to be checked
Check
Also review the “SAFETY CONSIDERATIONS”.
b. Items to be checked at time of delivery
Items to be checked
Did you explain about operations while showing the
operation manual to your customer?
Did you hand the operation manual and warranty over to
your customer?
Did you explain to your customer how to maintain and
clean local procurements such as the air filter, suction
grille, and air outlet grille?
Did you hand manuals of local procurements (in case
equipped) over to your customer?
3.
Check
SELECTING INSTALLATION SITE
CAUTION
(Other)
• Operation manual
• Installation manual
Small (2)
2 pcs.
a. Items to be checked after completion of work
BRC1E71, BRC1D71
BRC4C82
• If you think the humidity inside the installation space might
exceed 86°F and RH80%, reinforce the insulation on the
unit body.
Use glass wool or polyethylene foam as insulation so that
the thickness is more than 2 in. and fits inside the installation
space opening.
(1) Select an installation site where the following conditions
are fulfilled and that meets with your customer’s approval.
• Where optimum air distribution can be ensured.
• Where nothing blocks air passage.
• Where condensate can be properly drained.
• Where the supports are strong enough to bear the
indoor unit weight.
• Where the false ceiling is not noticeably on an incline.
• Where sufficient clearance for maintenance and service
can be ensured. (Refer to Fig. 1-1 and Fig. 1-2)
English
3P250363-2B
16
FXTQ-PA
EDUS391000-F12
Installation
• Where piping between indoor and outdoor units is
possible within the allowable limit. (Refer to the installation manual for the outdoor unit.)
• If a return-air duct is not installed, carefully select the
place and method of product installation so that air flow
into the product will not be blocked.
WARNING
• When installing the unit horizontally, be sure to tilt the unit in
the direction shown in Fig. 1-2. If the unit is tilted in any other
way, water can leak.
• Ensure sufficient space for the bottom of the product
(H dimensions) so that a downward slope of 1/100 can
be maintained for drain piping, as described for the intake
duct installation and in “6. DRAIN PIPING WORK”.
If installed vertically
(Top view)
[ PRECAUTION ]
• Install the indoor and outdoor units, power supply wiring
and connecting wires at least 3.5 ft. away from televisions or radios in order to prevent image interference or
noise. (Depending on the radio waves, a distance of 3.3
ft. may not be sufficient to eliminate the noise.)
• If installing the wireless kit in a room with electronic
fluorescent lighting (inverter or rapid start type), the
remote controller’s transmission distance may be shortened. Indoor units should be installed as far away from
fluorescent lighting as possible.
24 or more
(length : in.)
Air outlet
(Front view)
DANGER
• Do not install unit in an area where flammable materials are
present due to the risk of an explosion resulting in serious
injury or death.
WARNING
• If the supporting structural members are not strong enough
to take the unit’s weight, the unit could fall out of place and
cause serious injury.
Fig. 1-1
Air inlet
H
4.
If installed horizontally
(1) When installing the product, refer to “3. SELECTING
INSTALLATION SITE” and consider the product size
as shown Fig. 2 and Table 1.
(Front view)
Air inlet
PREPARATIONS BEFORE INSTALLATION AND INSTALLATION
Air outlet
Fig. 2
H
1
(Side view)
D
C
B
E
11
A
24 or
more
Gas line
H
3-1/4
Fig. 1-2
F
G
1-1/8
Liquid line
1-3/16
H
(1-3/16) 2-7/8
I
(1-3/16)
(length: in.)
English
4
3P250363-2B
FXTQ-PA
17
Installation
EDUS391000-F12
Table 1
Model
12 · 18 type
24 · 30 · 36 ·
42 · 48 · 54
type
(4) Check if the unit is horizontally level.
A
463/4
531/4
B
22
24
C
171/2
D
191/2
20
22
E
10
12
F
G
H
I
14- 11- 17- 171/2 15/16 1/8 15/16
14- 11- 19- 191/2 15/16 5/8 15/16
(2) Make sure the range of the unit’s external static pressure is not exceeded. (up to 0.5 in.W.C. at “H” speed.)
CAUTION
• Make sure the unit is installed level using a level tube: four
sides. (One thing to watch out for in particular is if the unit is
installed so that the slope is not in the direction of the drain
piping, this might cause leaking.)
If installed vertically
(3) Condensation may form on the product during COOL
operation. 9OUMAYNEEDto provide and INSTALLA
SECONDFIELDSUPPLIEDdrain pan.
Level
If installed vertically
If installed horizontally
Level
Second drain pan
Drain piping
If installed horizontally
(5) Secure the unit firmly to prevent it from falling.
(6) When the unit is installed in a hot and humid place, it
is recommended to use the following drain pan insulation kit, which is an optional accessory.
Drain pan insulation Kit
Second drain pan
Vertically
Horizontally
12 · 18 type
DPI 36-42/20
DPIH 36-42
24 · 30 · 36 ·
42 · 48 · 54 type
DPI 48-60/20
DPIH 48-61
Drain piping
• Regarding the attachment of the drain pan insulation kit,
refer to the installation manual provided with the kit.
5
English
3P250363-2B
18
FXTQ-PA
EDUS391000-F12
5.
Installation
REFRIGERANT PIPING WORK
〈Observe the requirements listed below for refrigerant
piping sizes.〉
Liquid
Gas
12 · 18 type
1/4 in.
1/2 in.
24 · 30 · 36 ·
42 · 48 · 54 type
3/8 in.
5/8 in.
〈Execute heat insulation work completely on both sides of
the gas piping and the liquid piping or else a water leakage might result.
Failing to insulate the pipes may cause leaking or burns.
"ESURETOUSEINSULATIONTHATISDESIGNEDFORUSEWITH(6!#
3YSTEMS
Reinforce the insulation on the refrigERANT
piping according to the installation environment. If
the temperature or humidity in the product installation
location might reach 86°F or 80%, respectively. Condensation may form on the surface of the insulation.〉
CAUTION
Follow the points at below.
• Use a tube cutter and flare suitable for the type of refrigerant.
• To prevent dust, moisture or other foreign matter from infiltrating the piping, either pinch the end or cover it with tape.
• Do not allow anything other than the designated refrigerant
to get mixed into the refrigerant circuit, such as air. If any
refrigerant gas leaks while working on the unit, immediately
ventilate the room.
• Cut off the pipe end with a tube cutter.
(Both liquid line and gas line)
Cut with a tube cutter
(2) Connect the piping.
1. Remove the upper and lower front panels.
2. Slide the front panel (lower) along the field piping until it
is far enough away that it will not be affected by heat
from brazing, as shown in Fig. 3.
3. Braze up to the field piping fitting port while cooling the
sensor and the thermal insulation.
4. Close the upper and lower front panels once heat from
the brazed areas has dissipated.
NOTE
• When brazing the field piping, cover the pipe insulation and
the thermal sensor inside the insulation with a damp cloth to
prevent any damage to the sensor or the insulation. Otherwise, the sensor may be damaged by heat of brazing, which
lead to a failure of normal operation.
Field piping fitting port (brazed)
Field piping
(1) Cut off the spin closure.
• The outdoor unit is charged with refrigerant.
• This coil contains gas under 150 P.S.I.G.
Release pressure from the gas piping pressure-release
device before initiating piping work.
Cap
After the work is finished,
try to repair.
Sharp object
(1) Remove
(2) Push
Fig. 3
(3) After the work is finished, make sure to check that
there is no gas leak.
Detail
Pressure
release device
Front panel
(4) After checking for gas leaks, be sure to insulate the
piping connections referring to Fig. 4.
Do not leave a gap
Gas piping
Gas piping
Liquid piping
Air
handler
Fig. 4
English
Piping heat insulation
material
Liquid piping
6
3P250363-2B
FXTQ-PA
19
Installation
EDUS391000-F12
(1) Install drain piping as described Fig. 6.
CAUTION
• Be sure to insulate any field piping all the way to the piping
connection inside the unit. Any exposed piping may cause
condensation or burns if touched.
In case of vertical installation
• When brazing the refrigerant piping, perform nitrogen replacement first, or perform the brazing while feeding nitrogen into the refrigerant piping. (Refer to Fig. 5)
Pressure-reducing valve
Part to be brazed
Nitrogen
Refrigerant piping
Taping
hands
valve
Nitrogen
Fig. 5
CAUTION
Secondary drain piping connection hole
Fig. 6-1
Primary drain piping connection hole
In case of horizontal installation
• When brazing piping while feeding nitrogen inside the
piping, make sure to set the nitrogen pressure to 2.9 psi or
less using the pressure reducing valve.
(This pressure is such that a breeze is blown to your cheek.)
DANGER
• Use of oxygen could result in an explosion resulting in
serious injury or death. Only use dry nitrogen gas.
• Refrigerant gas may produce toxic gas if it comes in contact
with fire such as from a fan heater, stove or cooking device.
Exposure to this gas could cause severe injury or death.
NOTE
• Do not use flux when brazing refrigerant piping. Therefore,
use the phosphor copper brazing filler metal (BCuP) which
does not require flux.
Flux has an extremely negative effect on refrigerant piping
systems. For instance, if chlorine based flux is used, it will
cause piping corrosion. Flux containing fluorine will damage
refrigerant oil.
6.
DRAIN PIPING WORK
CAUTION
• Make sure all water is out before making the duct connection.
Fig. 6-2
Reinstall the cover.
Remove the cover
Primary drain piping connection hole
Secondary drain piping
connection hole
• Perform drain work so that the unit is drained thoroughly.
(Be sure to insulate the following 2 locations since
condensation may cause water leakage.)
• Drain piping
• Drain socket
• The drain pan has connections for a primary and secondary drain.
• Use 3/4 PVC piping for drain piping connections.
• Keep piping runs short with a downward slope of at
least 1/100 to prevent air pocket from forming.
• Be sure to install a drain trap at the drain outlet since
the inside of the unit is at negative pressure relative to
atmospheric pressure during operation.
• Knock out the plastic seal with a screwdriver and a
hammer.
(Refer to Fig. 7)
NOTE
• In case of horizontal installation, carefully knock out the
plastic seal. Operation without opening the drain piping
connection hole causes water leakage.
7
English
3P250363-2B
20
FXTQ-PA
EDUS391000-F12
Installation
• To keep the piping from becoming clogged with dirt,
avoid bends where possible and install so that traps can
be cleaned.
Air handler
At least
4 in.
At least
3 in.
Fig. 7
• Observe the following guidelines when installing concentrated drain piping. Select the thickness of the
concentrated drain piping to reflect the capacity of the
machine to which it will be connected. (Install a drain
trap for each indoor unit.) (Refer to Fig. 8)
• If the metal duct passes through a metal lath, wire lath, or
metal plate of a wooden structure, isolate the duct from the
wall electrically.
• Be sure to heat-insulate the duct to prevent the formation of
condensation. (Material: Glass wool or polyethylene foam;
thickness: 1 inch.)
• Explain to the customer how to operate and clean fieldsupplied components such as air filters, air inlet grilles, air
outlet grilles.
• To prevent drafts, locate the air outlet grille on the indoor
side so that warm air from the outlet does not come into
direct contact with room occupants.
• When an electric heater (optional) is installed, use metal
duct and wrap the duct with a glass-wool insulation material.
8.
ELECTRIC WIRING WORK
8-1 GENERAL INSTRUCTIONS
At least 4 in.
Fig. 8
Concentrated drain piping
(Use a downward slope of at least 1/100.)
CAUTION
• Water accumulating in the drain piping can cause the drain
to clog.
〈PRECAUTIONS〉
Drain piping connections
• Do not connect the drain piping directly to sewage piping
that smell of ammonia. The ammonia in the sewage might
enter the indoor unit through the drain piping and corrode
the heat exchanger.
• Do not twist or bend the drain hose, as excessive force may
cause it to leak.
• Shut off the power before doing any work.
• All field supplied parts and materials, electric works must
conform to local codes.
• Use copper wire only.
• See also the “Wiring Diagram Label” located inside the unit’s
fan housing.
• For details on hooking up the remote controller, refer to the
“REMOTE CONTROLLER INSTALLATION MANUAL”
• All wiring must be performed by an authorized electrician.
• This system consists of multiple indoor units. Mark each
indoor unit as unit A, unit B . . . , and be sure the terminal
board wiring to the outdoor unit and Branch Selector unit are
properly matched. If wiring and piping between the outdoor
unit and an indoor unit are mismatched, the system may
cause a malfunction.
• Install a wiring interrupter or ground-fault circuit interrupter
for the power wiring.
• Make sure the ground resistance is no greater than 100Ω.
• To avoid short circuiting the power supply wire, be sure to
use insulated terminals.
• Do not turn on the power supply (wiring interrupter or
ground-fault circuit interrupter) until all other work is done.
DANGER
(2) After piping work is finished, check drainage flows
smoothly.
• Gradually insert approximately 1 quart of water into the
drain pan to check drainage in the manner described
below.
• Do not ground units to water piping, telephone wires or
lightning rods because incomplete grounding could cause a
severe shock hazard resulting in severe injury or death, nor
to gas piping because a gas leak could result in an explosion which could lead to severe injury or death.
7.
8-2 LIST OF STANDARD WIRING EQUIPMENT
INSTALLING THE DUCT
Exercise care regarding the following when performing duct
work.
• Verify that duct work does not exceed the unit’s setting range
of external static pressure (up to 0.5 Wg at “H” speed).
• Install canvas ducts at air outlets and inlets so that vibrations
from the main unit are not transmitted to ducts or the floor.
Additionally, line the duct with sound-absorbing material
(heat insulation material) as necessary.
• Be sure to install a optional air filter to the product’s air inlet
or to a field-supplied air inlet inside the air passage on the
suction side.
• Perform the curing and other work during duct welding so
that the inside of the product is not exposed to spatter.
English
Power supply wiring
(including ground wire)
Transmission wiring
Remote controller wiring
FUSEBREAKER
Size
Wire
Size
15A
Must comply
with local
codes.
2-conductor,
stranded, nonshielded copper/
PVC or vinyl jacket
AWG18 – 16
8
3P250363-2B
FXTQ-PA
21
Installation
EDUS391000-F12
NOTES
1. If the wiring is in a place where people it can be easily
touched by people, install a ground-fault circuit interrupter
to prevent electric shock.
2. When using a ground-fault circuit interrupter, make sure to
select one useful also to protection against overcurrent and
short-circuit.
When using a ground-fault circuit interrupter only for
grounding device, make sure to use a wiring interrupter
together.
• The length of the transmission wiring and remote controller
wiring are as follows.
If the wiring gets too hot due to loose power-supply wiring, use the following precautions:
• For wiring, use the designated power supply wiring and
connect firmly, then secure to prevent outside pressure
being exerted on the terminal board.
• Use the correct screwdriver for tightening the terminal
screws. If the blade of screwdriver is too small, the head of
the screw might be damaged, and the screw will not be
properly tightened.
• If the terminal screws are tightened too hard, screws might
be damaged.
• Refer Table 2 for the tightening torque of the terminal screws.
Length of the transmission wiring and remote controller wiring
Table 2
Outdoor unit – Indoor unit
Max. 3280 ft.
(Total wiring length: 6560 ft.)
Indoor unit – Remote controller
Max. 1640 ft.
Terminal block
Tightening torque (ft · lbf)
Remote controller / transmission
wiring terminal block (6P) (10P)
Power supply wiring terminal
block (3P)
0.58 – 0.72
0.87 – 1.06
8-3 ELECTRICAL CHARACTERISTICS
(1) Remove the front panel (upper).
Units
Model
12 type
18 type
24 type
30 type
36 type
42 type
48 type
54 type
Hz
Volts
208/
230
60
Power supply
Fan motor
Voltage
range
MCA
HP
Min. 187
Max. 229/
Min. 207
Max. 253
1.1
1.9
1.6
2.4
3.3
4.0
6.0
8.0
MOP
1/2
15
3/4
Top panel
FLA
0.9
1.5
1.3
1.9
2.6
3.2
4.8
6.4
Electric
components
box cover
Low-voltage
hole
High-voltage
hole
MCA: Minimum Circuit Amps (A)
MOP: Max Overcurrent Protective Device (A)
HP: Fan motor output (HP)
FLA: Full Load Amps (A)
(2) Remove the electric component box cover.
9.
WIRING EXAMPLE
Terminal block (6P)
9-1 HOW TO CONNECT WIRINGS
〈Precautions when laying power supply wiring〉
• Wiring of different thicknesses cannot be connected to the
power supply wiring terminal block. Slack in the power
supply wiring may cause abnormal heat.
• Use sleeve-insulated round crimp-style terminals for connections to the power supply wiring terminal block. When
none are available, connect wires of the same diameter to
both sides, as shown in the figure.
Terminal block (3P)
Insulation sleeve
Round crimp-style terminal
Connect wires of
the same gauge to
both sides.
9
Do not connect
wires of the same
gauge to one side.
Electric wire
Do not connect
wires of different
gauges.
(3) Pass the power supply wiring and the ground wire
through the top panel’s high-voltage hole (requires
use of conduit) and pass the remote controller wiring
and transmission wiring through the top panel’s
low-voltage hole.
• Pass the included insulation tube through the hole in the
panel before connecting the electric wires and the
ground wire to the terminal block (3P) shown in Fig. 9.
• Pass the included insulation tube through the hole in the
panel before connecting the remote controller wiring
and transmission wires to the terminal block (6P) shown
English
3P250363-2B
22
FXTQ-PA
EDUS391000-F12
Installation
in Fig. 10.
• Then secure them in place with the included clamp
material (1) as shown in Fig. 10 to protect them from
external force from outside the unit.
• If the power supply voltage is 208V, change the transformer wire connection from the 240V terminal to the
208V terminal. (Refer to Fig. 11)
How to use insulation tube.
• Use the insulation tube to cover the wiring.
• Joint the insulation tube with the tape and cut off the tube
sticking out of the unit.
Tape
Insulation tube large (3)
Terminal block (3P)
Insulation tube
small (2)
Insulation tube
Cut off the sticking
out of the unit.
L2
L1
POWER
(4) Install the electric component box cover.
Fig. 9
Terminal
block (6P)
Transformer
(5) Pass the power supply wiring and the ground wire
through the conduit (conduit should be field supplied). The hole for running wires through should be
sealed completely to prevent air from entering.
* When installing an optional electric heater kit, run both
the power supply wiring and ground wire of the electric
heater kit through the conduit. (Refer to 10-5 (8))
Pass through the
conduit
Remote controller and
transmission wiring
Insulation tube
Clamp material (1)
(accessory)
Fig. 10
Power supply wiring
and ground wire
Clamp material (1)
(accessory)
Changing the transformer wire connection
Connector
(Connect the wire to the 208V terminal.
Be sure to insert the wire securely until
a clicking sound is produced.)
DANGER
Cap
(Change the
connection.)
Wire (Red)
COM
208V 240V
Wire
(Red)
COM
208V 240V
Connector
Cap
(6) Install the front panel (upper).
• Use only specified wire and connect wires to terminals
tightly. Be careful that wires do not place external stress on
terminals. Keep wires in neat order so as to not to obstruct
other equipment. Make sure that the electric component box
cover closes tightly. Incomplete connections could result in
overheating, and in worse cases, electric shock or fire.
WARNING
• Never connect power supply wiring to the terminal block for
remote controller wiring as this could damage the entire
system.
Ÿ230V power supply (factory set)®
Fig. 11
Ÿ208V power suppy®
CAUTION
• When doing the wiring, make sure the wiring is neat and
does not cause the electric component box cover to stick up,
then close the cover firmly. When attaching the electric
component box cover, make sure you do not pinch any
wires.
English
10
3P250363-2B
FXTQ-PA
23
Installation
EDUS391000-F12
• Outside the air conditioners, separate the low voltage wiring
(remote controller and transmission wiring) and high voltage
wiring (ground wire and power supply wiring) by at least 5 in.
so that they do not pass through the same place together.
Proximity may cause electrical interference, malfunctions,
and breakage.
[ PRECAUTIONS ]
• Refer to the “REMOTE CONTROLLER INSTALLATION
MANUAL” on how to install and lay the wiring for the remote
controller.
• See also the “Wiring Diagram Label” located inside the unit’s
fan housing.
• Connect the remote controller and transmission wiring their
respective terminal blocks.
No. 3 system
When including BS unit
Power supply
single phase
60Hz 208/230V
Outdoor unit
IN/D OUT/D
F1 F2 F1 F2
L1 L2
Indoor unit A
P1 P2
Power supply
single phase
60Hz 208/230V
Outdoor unit
L1 L2
• When using 2 remote controllers, one must be set to “MAIN”
and the other to “SUB”.
• If the remote controller to be used is Model BRC1E71, read
the installation manual supplied with the remote controller.
Power supply
single phase
60Hz 208/230V
L1 L2
Remote controller
(option)
9-2 CONTROL BY 2 REMOTE CONTROLLERS (Controlling 1 indoor unit by 2 remote controllers)
[ WIRING EXAMPLE ]
No. 1 system When using 1 remote controller for
1 indoor unit
IN/D
OUT/D IN/D
F1 F2 F1 F2
P1 P2 F1 F2 T1 T2
CAUTION
• Do not, under any circumstances, connect the power supply
wiring to the remote controller or transmission wiring terminal block. Doing so can destroy the entire system.
Power supply
single phase
60Hz 208/230V
BS unit
L1 L2
L1 L2
OUT/D
MAIN/SUB CHANGEOVER
F1 F2 F1 F2
(1) Insert a
screwdriver into the recess between the
upper and lower part of remote controller and, working from the 2 positions, pry off the upper part.
The remote controller PC board is attached to the upper
part of remote controller.
L1 L2
L1 L2
P1 P2 F1 F2 T1 T2
Indoor unit A
P1 P2 F1 F2 T1 T2
P1 P2
Remote controller
(option)
No. 2 system
Upper part of
remote controller
P1 P2
Remote controller
(option)
Remote controller
(option)
Lower part of
remote controller
For group control or use with 2 remote
controllers
Insert the screwdriver here and gently work
off the upper part of remote controller.
Power supply
single phase
60Hz 208/230V Outdoor unit
Note) There is not need to set the indoor unit
address when using group control.
(It is automatically set when the power
is turned on.)
L1 L2
IN/D OUT/D
F1 F2 F1 F2
P1 P2 F1 F2 T1 T2
L1 L2
P1 P2 F1 F2 T1 T2
L1 L2
P1 P2 F1 F2 T1 T2
Indoor unit B
Indoor
unit A
P1 P2
Remote controller
(option)
11
P1 P2 F1 F2 T1 T2
Most
downstream
Indoor unit
Indoor unit B
P1 P2
L1 L2
L1 L2
Case of group control
P1 P2
Most downstream
indoor unit
P1 P2
(MAIN) (SUB)
Remote
controller
(option)
(2) Turn the MAIN/SUB changeover switch on one of the
two remote controller PC boards to “S”.
(Leave the switch of the other remote controller set to “M”.)
(Factory setting)
S
M
Remote controller
PC board
Only one remote controller
needs to be changed
if factory settings have
remained untouched.
S
M
For use with 2
remote controllers
English
3P250363-2B
24
FXTQ-PA
EDUS391000-F12
Installation
Wiring Method (See ‘‘8. ELECTRIC WIRING WORK’’)
10. FIELD SETTING AND TEST RUN
(3) Remove the electric component box cover.
〈Field settings may have to be performed using the remote controller, depending on the type of installation.〉
(4) Add remote controller 2 (SUB) to the terminal block
for remote controller (P¹, P²) in the electric component
box.
(There is no polarity.)
P1 P2 F1 F2 T1 T2
REMOTE
CONTRL
TRANSMISSION
WIRING
FORCED
OFF
Remote controller wiring
terminal block
Remote
controller 2
(SUB)
Remote
controller 1
(MAIN)
[ PRECAUTIONS ]
• Crossover wiring is needed when using group control and 2
remote controllers at the same time.
• Connect the indoor unit at the end of the crossover wire (P¹,
P²) to remote controller 2 (SUB).
Indoor unit 1
Max. No. of
indoor units
Indoor unit 2
(1) Make sure the electric component box covers are
closed on the indoor and outdoor units.
(2) Depending on the type of installation, make the field
settings from the remote controller after the power is
turned on, following the “Field Settings” manual which
came with the remote controller.
• The settings can select “Mode No.”, “FIRST CODE NO.”
and “SECOND CODE NO.”.
• The “Field Settings” included with the remote controller
lists the order of the settings and method of operation.
SECOND
CODE NO.
Mode No.
FIRST
CODE NO.
FIELD SET
MODE
SETTING
• Lastly, make sure the customer keeps the “Field Settings”
manual, along with the operating manual, in a safe place.
10-1 SETTINGS WHEN USING THE OPTIONAL REMOTE SENSOR
Crossover wire (P1.P2)
Remote controller 1
(MAIN)
Remote controller 2
(SUB)
9-3 REMOTE CONTROL (FORCED OFF AND ON/
OFF OPERATION)
• Connect input lines from the outside to the terminals T¹ and
T² on the terminal block (6P) for remote controller to achieve
remote control.
• See the “10. FIELD SETTING AND TEST RUN” for details
on operation.
P1 P2 F1 F2 T1 T2
REMOTE
CONTRL
TRANSMISSION
WIRING
FORCED
OFF
This product does not include an air inlet thermistor.
It uses a remote controller thermistor for control purposes.
For this reason, it is necessary to install an optional remote
thermistor in the following cases:
• When the remote controller will be installed at a location
where it cannot accurately measure the indoor temperature.
• When using a remote controller without a built-in thermistor
(simple remote controller, wireless remote controller, no
remote controller).
When using an optional remote sensor, change the settings as
described Table 3:
Table 3
Mode No.
To use both the remote
controller thermistor and the
remote sensor
To use only the remote sensor
To use only the remote
controller thermistor
Input A
Wire specification
Gauge
01
10 (20)
2
02
03*
* factory set
Sheathed vinyl cord or cable (2 wires)
AWG18 – 16
Length
External terminal
FIRST
SECOND
CODE NO. CODE NO.
Max. 328 ft.
Contact that can ensure the minimum
applicable load of 16 V DC, 1 mA.
9-4 CENTRALIZED CONTROL
• For centralized control, it is necessary to designate the
group No. For details, refer to the manual of each optional
controller for centralized control.
English
12
3P250363-2B
FXTQ-PA
25
Installation
EDUS391000-F12
(2) Insert the air filter as far as it can go.
10-2 REMOTE CONTROL SETTING
• Forced off and ON/OFF operation should be selected by
selecting the SECOND CODE NO. as shown in Table 4.
Table 4
External ON/OFF input
Mode No.
Forced off
ON/OFF operation
12 (22)
FIRST
SECOND
CODE NO. CODE NO.
01*
1
02
* factory set
• Input A of forced off and ON/OFF operation work as shown
in Table 5.
Table 5
Forced off
Input A “on” to force a stop
(remote controller reception
prohibited)
Input A “off” to allow remote
controller
ON/OFF operation
Unit operated by changing input
A from “off” to “on”
Unit stopped by changing input A
from “on” to “off”
Air filter (optional accessories)
10-5 INSTALLATION OF THE ELECTRIC HEATER KIT
WARNING
10-3 SETTING THE FILTER SIGN DISPLAY INTERVAL
• Explain the following to the customer if the filter dirt settings
have been changed.
• The filter sign display time is set to 2500 hours (equivalent
to 1 year’s use) when shipped.
• The settings can be changed to not display.
• When installing the unit in a dusty place, set the filter sign
display time to shorter intervals (1,250 hours).
• Explain it to the customer that the filter needs to be cleaned
regularly to prevent clogging and also the time that is set.
Mode No.
FIRST CODE NO.
0
10 (20)
1 (low/high)
Filter dirt
Displayed time
(units: hours)
Filter sign display
SECOND
CODE NO.
01
02
low
high
2500/
10000/
1250
5000
ON
OFF
All phases of the electrical installation must comply with national, state, provincial, and local codes.
When connecting an electric heater, be sure to install a GROUNDleakaGEBREAKER
)FAGROUNDCIRCUITISNOTINSTALLEDELECTRICAL
shock or fire may result.
Regarding the rated current of the GROUND leakage circuit breaker to be installed, refer to the H.M.C.A. value indicated
on the manufacturer’s label or in a technical document.
The recommended rapid sensitive current and tripping time are indicated below.
Recommended specifications of circuit breaker
Rapid sensitive current
30mA
Tripping time
0.1sec
• Purchase and install the air filter as in Table 6.
• Purchase and install the electric heater kit as in Table 7.
• Also refer to the installation and operating instructions that
come with the electric heater kit.
• The indoor unit fan operates at H speed during HEATER
operation.
Table 6
Table 7
3
10-4 INSTALLATION OF THE OPTIONAL AIR FILTER
12 · 18 type
24 · 30 · 36 · 42 · 48 · 54 type
Electric heater kit model name
Air filter
FIL 36-42
FIL 48-61
(1) Take off the part on the bottom of the front panel.
Model
HKR03
HKR05C
HKR06
HKR08C
HKR10C
HKR15C
HKR20C
12 type
18 type
1
24 type
1
30 · 36 type
1
1
42 type
1
1
1
1
2
48 · 54 type
1
1
1
1
2
2
1
: Auxiliary and Heat Pump Lockout: Electric heater operation with heat pump is allowed.
: Heat Pump Lockout: Only electric heater operation is
allowed. Heat pump and electric heater cannot operate at
the same time.
2
: Heat Pump Lockout: Only electric heater operation is allowed. Heat pump and electric heater cannot operate at the
same time. In addition, acceptable 2 step heating control.
13
English
3P250363-2B
26
FXTQ-PA
EDUS391000-F12
Installation
(1) Turn off power supply to all indoor and outdoor units.
(2) Remove the front panel (upper) and the electric heater
slot cover.
(5) Install the circuit breaker mounting bracket removed
in step (3) into the blower deck.
* The HKR-03 and HKR-06 have no circuit breaker mounting bracket; Procure and install a circuit breaker.
Electric heater slot cover
(6) Connect the relay connector of the heater kit to the relay
connector of the product. Disconnect the empty connector connected to the relay connector of the product.
Front panel (upper)
(3) Remove the circuit breaker mounting bracket from the
heater element in the electric heater kit by removing
the 2 screws. (Do not remove the harness)
* The HKR-03 and HKR-06 have no circuit breaker mounting bracket, so proceed from the next step.
Heater element
Circuit breaker mounting bracket
(7) Check that the circuit breaker is turned off, and connect the heater kit to the wiring on site.
Power supply wiring
Ground wire
(4) Insert the heater element in the electric heater kit into the
electric heater slot, and use six of the screws taken out
in step (2) to install it. When doing so, check that airflow
is matched. Refer to the heater kit for details of airflow.
HKR-05C, 08C, 10C
HKR-15C, 20C
* When using HKR-03, 06, connect the power supply wire to the
terminal block located inside the main unit of the heater element.
* When using HKR-03, 05C, 06, 08C, 10C, connect the ground
wire to the terminal block for indoor units. (The terminal block
is located on the air outlet side of the blower deck.)
*If the HKR-15C/20C is used, connect the ground wire to
the both terminals.
The terminal blocks for ground wire are located on the air
outlet side of the indoor unit blower deck and on the
circuit breaker mounting bracket of the electric heater kit.
English
14
3P250363-2B
FXTQ-PA
27
Installation
EDUS391000-F12
(8) Pass the power supply wiring and the ground wire
through the conduit (conduit should be field supplied). The hole for running wires through should be
sealed completely to prevent air from entering.
(11) Confirm that there are no mistakes with the wiring,
and install the front panel (upper).
Pass through the conduit
Power supply wiring
and ground wire
(9) Select the corresponding electric heater from the
electrical wiring diagram and mark the checkbox (
for the electric heater with “ ”.
)
(10) Open the knock hole of the plastic cover provided for
the front panel (upper) so that the circuit breaker will
be turned on and off through the hole.
* This step is not required for HKR-03 and HKR-06.
Proceed to the next step.
Plastic cover
(12) On-site setting of heater
(12) -1 Electric heater capacity setting
Electric Heater capacity
setting (Optional kit)
HKR-03, 05, 06, 08, 10,
15, 20 type
Without heater
Mode No.
FIRST
CODE NO.
11 (21)
5
SECOND
CODE NO.
01
03*
* factory set
HK
R-0
5C
, 08
C,
10
C
HK
R-1
Front panel (upper)
15
5C
, 20
C
English
3P250363-2B
28
FXTQ-PA
EDUS391000-F12
Installation
(12) -2 Electric heater operating mode setting
〈When electric heater is used in “Heat Pump lockout
mode”〉
• Check the heater capacity. (Select heater marked with “ ” or
“ 2” in Table 8.)
• Perform on-site setting using the remote controller.
• Set the “heat pump lockout mode” using the outdoor unit.
(Refer to the service manual for the outdoor unit.)
〈When used as “Auxiliary electric heater”〉
• Check the heater capacity. (Select heater marked with “ 1” in
Table 8.)
• Perform on-site setting using the remote controller.
Table 8
WARNING
• If the unit is installed with an electric heater, install the
optional product at a location where it is not exposed directly
to the heat from the electric heater. Direct exposure to heat
can result in an equipment malfunction or fire.
(2) Connect the wires
• Run the wires through the low-voltage hole.
• Connect the wires to the terminal block (10P) of the
product. The terminal Nos. for wire connection are
shown below. Refer to the information as needed.
Terminal Nos. are indicated on the name plate for the
terminal block.
Electric heater kit model name
Model
HKR03
HKR05C
HKR06
HKR08C
HKR10C
HKR15C
Terminal
block (10P)
HKR20C
1
24 type
1
30 · 36 type
1
1
42 type
1
1
1
1
2
48 · 54 type
1
1
1
1
2
Electric Heater kit setting
(Optional kit)
Mode No.
FIRST
CODE NO.
2
1
18 type
2 3 4 5 6 7 8 9 10
12 type
SECOND
CODE NO.
Heat Pump lock out mode
01*
Auxiliary electric heater &
Heat Pump Lockout mode
available
11 (21)
03
3
Terminal No. Input/output signal
* factory set
1, 2
Outputs: indoor unit ON signal. (AC 24V)
(12) -3 Electric heater ON/OFF temperature setting
3, 4
• While in heating operation, the heater control (ON/OFF) is
conducted as shown below;
Outputs: indoor unit cooling THERMO ON
signal. (AC 24V)
5, 6
Receives input: Air purifier operation ON
signal. (dry contact)
7, 8
Receives input: Humidifier operation ON
signal. (dry contact)
9, 10
Receives input: Forced closure of Indoor Unit
Electronic Expansion Valve during cooling
operation. (dry contact)
Set temperature
ON
OFF
<Toff: F°>
<Ton: F°>
(3) On-site setting of air purifier/humidifier
• Perform on-site setting using the remote controller.
Mode
No.
Mode No. FIRST CODE NO.
FIRST
CODE CODE
NO.
01*
02
03
04
05
06
<Ton>
-7.2
-6.3
-5.4
-4.5
-3.6
-2.7
<Toff>
-3.6
-2.7
-1.8
-0.9
0
0.9
10 (20)
7
SECOND CODE NO.
14 (24)
14 (24)
* factory set
10-6 SETTING FOR LOCAL SUPPLIED OPTION.
(1) Installation of the humidifier, economizer and air
purifier (UV lamp)
• Humidifier, economizer and air purifier (UV lamp) are
sold separately. For the method of installation, refer to
the manual provided with each optional product.
English
4
5
01
02
FAN SPEED
UNDER
OPERATING
purifier and
humidifier
Refer to
remote
controller
setting
SPEED
H*
FAN RESIDUE TIME
FOR HUMIDIFIER
30 [sec]
60* [sec]
03
120 [sec]
* factory set
10-7 SETTINGS FOR SEPARATELY SOLD ACCESSORIES
• See the instruction manuals included with optional accessories for the necessary settings.
16
3P250363-2B
FXTQ-PA
29
Installation
EDUS391000-F12
〈When using a wireless remote controller〉
• A wireless remote controller address needs to be set when
using a wireless remote controller. See the installation
manual included with the wireless remote controller for
details on how to make the settings.
Perform a test run according to the outdoor unit’s installation manual.
• The operation lamp of the remote controller will flash when a
malfunction occurs. Check the malfunction code on the
liquid crystal display to identify the point of trouble. An
explanation of malfunction codes and the corresponding
trouble is provided in “CAUTION FOR SERVICING” of the
outdoor unit.
If the display shows any of the following, there is a possibility
that the wiring was done incorrectly or that the power is not
on, so check again.
Remote control display
“
” display
Content
• There is a short circuit at the FORCED
OFF terminals (T¹, T²).
“ U3 ” display
• The test-run has not been performed.
“ U4 ” display
“ UH ” display
• The power on the outdoor unit is off.
• The outdoor unit has not been wired for
power supply.
• Wiring is incorrect for the transmission
wiring and / or FORCED OFF wiring.
• The transmission wiring is cut.
“ UF ” display
No display
• Reversed transmission wiring
• The power on the indoor unit is off.
• The indoor unit has not been wired for
power supply.
• Wiring is incorrect for the remote controller wiring, the transmission wiring and /
or the FORCED OFF wiring.
• The remote controller wiring is cut.
CAUTION
• Always stop the test run using the remote controller to stop
operation.
17
English
3P250363-2B
30
FXTQ-PA
EDUS391000-F12
Accessories
9. Accessories
Standard Accessories
Name
Clamp material (1)
Insulation tube
Quantity
4 pcs.
1 set
(Other)
• Operation manual
• Installation manual
Shape
Small (2)
2 pcs.
Large (3)
2 pcs.
3P250363-2B
Optional Accessories (For Controls): Refer to booklet of “Controls”.
Optional Accessories (For Unit)
FXTQ~PAVJU
No. Item
12
1
Air filter
2
Insulation kit (Vertical installation)
3
Insulation kit (Horizontal installation)
4
24
30
36
42
FIL 36-42
FIL 48-61
DPI 36-42/20
DPI 48-60/20
DPIH 36-42
DPIH 48-61
48
54
HKR-03, HKR-05C, HKR-06, HKR-08C, HKR-10C, HKR-15C, HKR-20C.
• HKR-C has circuit breaker.
• For details, see below table.
Electric heater kit
Model name
18
Electric heater capacity
HKR-03
HKR-05C
HKR-06
HKR-08C
HKR-10C
HKR-15C
HKR-20C
FXTQ12PAVJU
k
k
×
×
×
×
×
FXTQ18PAVJU
.
k
k
×
×
×
×
FXTQ24PAVJU
.
k
k
k
k
×
×
FXTQ30PAVJU
.
.
k
k
k
×
×
FXTQ36PAVJU
.
.
k
k
k
×
×
FXTQ42PAVJU
.
.
.
.
k
k Note 1)
×
FXTQ48PAVJU
.
.
.
.
k
k Note 1)
k Note 1)
FXTQ54PAVJU
.
.
.
.
k
k Note 1)
k Note 1)
. : Electric heater operation with heat pump is allowed.
k : Only electric heater operation is allowed.
× : Not allowed.
Note: 1. Acceptable for 2-step control.
C: 3D068224A
FXTQ-PA
31
Accessories
32
EDUS391000-F12
FXTQ-PA
Daikin Industries, Ltd.’s products are manufactured for export to numerous countries throughout the
world. Daikin Industries, Ltd. does not have control over which products are exported to and used in a
particular country. Prior to purchase, please therefore confirm with your local authorized importer,
distributor and/or retailer whether this product conforms tot he applicable standards, and is suitable for
use, in the region where the product will be used. This statement does not purport to exclude, restrict or
modify the application of any local legislation.
dddddfdf
Ask a qualified installer or contractor to install this product. Do not try to install the product yourself.
Improper installation can result in water or refrigerant leakage, electrical shock, fire, or explosion.
Use only those parts and accessories supplied or specified by Daikin. Ask a qualified installer or
contractor to install those parts and accessories. Use of unauthorized parts and accessories or
improper installation of parts and accessories can result in water or refrigerant leakage, electrical
shock, fire, or explosion.
Read the User’s Manual carefully before using this product. The User’s Manual provides important
safety instructions and warnings. Be sure to follow these instructions and warnings.
If you have any inquiries, please contact your local importer, distributor, or retailer.
©
2010 Daikin Industries, Limited.
Daikin® AC Absolute Comfort®, and its design, VRV®, REFNET™, and Quaternity™ are registered trademarks of Daikin Industries, Limited. All rights reserved.
LonWorks® and LON® are registered trademarks of Echelon Corporation. BACnet® is a Data Communication Protocal for Building Automation and Control Networks,
developed under the auspices of the American Society of Heating, Refrigeratin, and Air-Conditioning Engineers (ASHRAE).
ISO 9001 is a plant certification system
defined by the International Organization
for Standardization (ISO) relating to
quality assurance. ISO 9001 certification
covers quality assurance aspects related
to the “design, development, manufacture,
installation, and supplementary service”
of products manufactured at the plant.
ISO 14001 is the standard defined by the
International Organization for Standardization
(ISO) relating to environmental management
systems. Our group has been acknowledged by
an internationally accredited program of
environmental protection procedures and
activities to meet the requirements of
ISO 14001.
AMERICAS
1645 Wallace Drive, Suite 110
Carrollton, TX75006
info@daikinac.com
www.daikinac.com
Specifications, designs and other content appearing in this brochure are current as of December 2012 but subject to change without notice.
EDUS391000-F12
Printed in U.S.A. 12/2012 B AK