D-Link DAP-1360 User manual

Wireless N Open Source Access Point
Table of Contents
Table of Contents
Package Contents.......................................................................... 4
System Requirements.................................................................. 5
Introduction.................................................................................... 6
Features............................................................................................. 8
Hardware Overview...................................................................... 9
Connections............................................................................ 9
LEDs..........................................................................................10
WPS LED/Button..................................................................11
Installation........................................................................12
Operation Modes.........................................................................12
Access Point Mode..............................................................13
Wireless Client Mode..........................................................14
Repeater Mode.....................................................................15
Bridge Mode..........................................................................16
Bridge with AP Mode.........................................................17
WISP Client Router Mode..................................................18
WISP Repeater Mode..........................................................19
Wireless Installation Considerations.....................................20
Configuration....................................................................21
Web-based Configuration Utility...........................................21
Wireless Setup Wizard................................................................22
Access Point Mode..............................................................23
Repeater Mode.....................................................................26
Wireless Client Mode..........................................................30
Manual Configuration................................................................34
Wireless Settings..................................................................34
D-Link DAP-1360 User Manual
Access Point Mode.........................................................35
Repeater Mode................................................................37
Wireless Client Mode.....................................................38
Bridge Mode.....................................................................39
Bridge with AP Mode....................................................40
WISP Client Router/WISP Repeater Modes............41
WAN Settings........................................................................42
Dynamic IP (DHCP).........................................................42
Static IP...............................................................................43
PPPoE..................................................................................44
PPTP.....................................................................................45
LAN Settings..........................................................................46
Static IP...............................................................................47
Advanced.......................................................................................48
Advanced Wireless..............................................................48
MAC Address Filter......................................................................49
Wi-Fi Protected Setup................................................................50
User Limits......................................................................................51
Port Forwarding (WISP modes only)....................................52
Port Filter (WISP modes only).................................................53
DMZ (WISP modes only)...........................................................54
Parental Control (WISP modes only)....................................55
Advanced Network (WISP modes only)..............................56
Maintenance.................................................................................57
Admin......................................................................................57
System.....................................................................................58
Language Pack......................................................................59
2
Table of Contents
Firmware.................................................................................59
Watchdog...............................................................................60
Time..........................................................................................61
System Check........................................................................62
Schedules...............................................................................63
Status...............................................................................................64
Device Info.............................................................................64
Logs..........................................................................................65
Statistics..................................................................................66
Wireless...................................................................................67
IPv6...........................................................................................68
Help..................................................................................................69
Troubleshooting...............................................................87
Wireless Basics..................................................................91
What is Wireless?..........................................................................92
Tips....................................................................................................94
Wireless Modes.............................................................................95
Networking Basics............................................................96
Check your IP address................................................................96
Statically Assign an IP address................................................97
Technical Specifications...................................................98
Wireless Security..............................................................70
What is WPA?.................................................................................71
Configure WPA/WPA2 Personal..............................................72
Configure WPA/WPA2 Enterprise...........................................73
Connect to a Wireless Network........................................74
Using Windows® XP.....................................................................74
Configure WPA-PSK.....................................................................75
Using Windows Vista® ................................................................77
Configure WPA-PSK.....................................................................79
Using Windows® 7........................................................................80
Configure WPS......................................................................83
D-Link DAP-1360 User Manual
3
Section 1 - Product Overview
Package Contents
DAP-1360 Wireless N Open Source Access Point
Ethernet Cable
Two Detachable Antennas
Power Adapter
CD-ROM with Manual
Note: Using a power supply with a different voltage rating than the one included with the DAP-1360 will cause damage and void
the warranty for this product.
D-Link DAP-1360 User Manual
4
Section 1 - Product Overview
System Requirements
Network Requirements
• An Ethernet-based Network
• IEEE 802.11n/g wireless clients (AP/Repeater Mode)
• IEEE 802.11n/g wireless network (Client/Bridge/Repeater Mode)
• 10/100 Ethernet
Computer with the following:
• Windows®, Macintosh, or Linux-based operating system
• An installed Ethernet adapter
Web-based Configuration
Utility Requirements
Browser Requirements:
• Internet Explorer® 6.0 and higher
• Mozilla Firefox 3.0 and higher
• Google™ Chrome 2.0 and higher
• Apple Safari 3.0 and higher
Windows® Users: Make sure you have the latest version of Java installed.
Visit www.java.com to download the latest version.
D-Link DAP-1360 User Manual
5
Section 1 - Product Overview
Introduction
D-Link, an industry leader in networking, introduces the new D-Link DAP-1360 Wireless N Open Source Access Point. With the
ability to transfer files with a maximum wireless signal rate of up to 300Mbps*, the DAP-1360 gives you high-speed wireless
network access for your home or office.
The DAP-1360 is Wi-Fi IEEE 802.11n compliant, meaning that it can connect and interoperate with other 802.11n compatible
wireless client devices. The DAP-1360 is also backwards compatible with 802.11b/g. It can be flexibly configured to operate in
7 different modes Access Point, Wireless Client, Bridge, Bridge with AP, Repeater, WISP Client Router or WISP Repeater.
With its Setup Wizard, the DAP-1360 ensures that you will be up and running on a wireless network in just a matter of minutes.
The DAP-1360 features Wi-Fi Protected Access (WPA-PSK/WPA2-PSK) to provide an enhanced level of security for wireless
data communications. The DAP-1360 also includes additional security features to keep your wireless connection safe from
unauthorized access.
The DAP-1360 supports WPS on the AP, repeater and wireless client operation modes,with each capable of being conveniently
set up by using the PIN method or Push Button.
• Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network
overhead, lower actual data throughput rate.
D-Link DAP-1360 User Manual
6
Section 1 - Product Overview
TOTAL PERFORMANCE
Combines award winning access point features and 802.11n wireless technology to provide the best wireless performance.
TOTAL SECURITY
The most complete set of security features including WPA/WPA2 encryption to protect your network against outside intruders.
TOTAL COVERAGE
Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.
ULTIMATE PERFORMANCE
The D-Link Wireless N Open Source Access Point (DAP-1360) is an 802.11n compliant device that delivers real world performance of
up to 13X faster than an 802.11g wireless connection (also faster than a 100Mbps wired Ethernet connection). Create a secure wireless
network to share photos, files, music, video, printers, and network storage throughout your home. Connect the DAP-1360 to router and
share your high-speed Internet access with everyone on the network. In addition, this Range Extender includes a Quality of Service
(QoS) engine that keeps digital phone calls (VoIP) and online gaming smooth and responsive, providing a better Internet experience.
EXTENDED WHOLE HOME COVERAGE
This high performance Wireless Bridge provides superior Whole Home Coverage while reducing dead spots. The DAP-1360 is designed
for use in bigger homes and for users who demand higher performance networking.
TOTAL NETWORK SECURITY
The DAP-1360 supports all of the latest wireless security features to prevent unauthorized access, be it from over the wireless network
or from the Internet. Support for WPA and WPA2 standards ensure that you’ll be able to use the best possible encryption method,
regardless of your client devices.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely
affect wireless signal range.
D-Link DAP-1360 User Manual
7
Section 1 - Product Overview
Features
• Faster Wireless Networking - The DAP-1360 provides up to 300Mbps* wireless connection with other 802.11n wireless
clients. This capability allows users to participate in real-time activities online, such as video streaming, online gaming,
and real-time audio.
• Compatible with IEEE802.11g Devices - The DAP-1360 is still fully compatible with the 802.11g standards, so it can
connect with existing 802.11g PCI, USB, and Cardbus adapters.
• Advanced Firewall Features - The Web-based user interface displays advanced network management features including
Content Filtering, which allows easily applied content filtering based on MAC Address.
• WPS PBC- (Wi-Fi Protected Setup Push Button Configuration) Push Button Configuration is a button that can be pressed
to add the device to an existing network or to create a new network. A virtual button can be used on the utility while
a physical button is placed on the side of the device.
This easy setup method allows you to form a secured wireless link between the DAP-1360 and another WPS enabled
device. A PC is no longer needed to log into the Web-based interface.
• WPS PIN - (Wi-Fi Protected Setup Personal Identification Number ) A PIN is a unique number that can be used to add
the access point to an existing network or to create a new network. The default PIN may be printed on the bottom of
the access point. For extra security, a new PIN can be generated. You can restore the default PIN at any time. Only the
Administrator (“admin” account) can change or reset the PIN.
• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DAP-1360 lets you control what
information is accessible to those on the wireless network, whether from the Internet or from your company’s server.
Configure your access point to your specific settings within minutes.
D-Link DAP-1360 User Manual
8
Section 1 - Product Overview
Hardware Overview
Connections
1
1
LAN Port
2
Power Receptor
3
Reset Button
D-Link DAP-1360 User Manual
2
3
Connect 10/100 Ethernet devices such as computers, switches, and hubs.
Receptor for the supplied power adapter.
Pressing the Reset Button restores the access point to its original factory default settings.
9
Section 1 - Product Overview
Hardware Overview
LEDs
1
2
3
4
1
Power LED
2
Wireless LED
A solid green light indicates the wireless function is working. The light will be off during
device reboot or if the wireless radio is disabled.
3
Security LED
A solid green light indicates that wireless security (WEP, WPA, WPA2) is enabled.
4
LAN LED
D-Link DAP-1360 User Manual
A solid green light indicates a proper connection to the power supply.
A solid green light indicates the LAN port connection is OK.
10
Section 1 - Product Overview
Hardware Overview
WPS LED/Button
1
1
WPS LED/Button
D-Link DAP-1360 User Manual
A solid light indicates a successful WPS connection. A blinking light indicates the
device is trying to establish a connection.
11
Section 2 - Installation
Installation
Please configure the DAP-1360 with a computer connected directly to the AP. The next few pages will explain the different
operational modes you can use.
Operation Modes
Depending on how you want to use your DAP-1360 will determine which mode you use. This section will help you figure out
which setting works with your setup.
•
•
•
•
•
•
•
Access Point mode - page 13
Wireless Client mode - page 14
Repeater mode - page 15
Bridge mode - page 16
Bridge with AP mode - page 17
WISP Client Router mode - page 18
WISP Repeater mode - page 19
D-Link DAP-1360 User Manual
12
Section 2 - Installation
Access Point Mode
In the Access Point mode, the DAP-1360 acts as a central connection point for any computer (client) that has a 802.11n or
backward-compatible 802.11g wireless network interface and is within range of the AP. Clients must use the same SSID (wireless
network name) and channel as the AP in order to connect. If wireless security is enabled on the AP, the client will need to enter
a password to connect to the AP. In Access Point mode, multiple clients can connect to the AP at the same time.
Computer
Internet
Modem
Router
DAP-1360
(in Access Point Mode)
Computer
D-Link DAP-1360 User Manual
13
Section 2 - Installation
Wireless Client Mode
In the Wireless Client mode, the DAP-1360 acts as a wireless network adapter for your Ethernet-enabled device (such as a game
console or a TV set-top box). Connect your Ethernet-enabled device to the AP using an Ethernet cable. The AP Client mode
can support multiple wired clients.
If you are going to connect several Ethernet-enabled devices to your DAP-1360, connect the LAN port of the DAP-1360 to an
Ethernet switch, then connect your devices to this switch.
Example: Connect a gaming console using an ethernet cable to the DAP-1360. The unit is set to Wireless Client mode which
will wirelessly connect to a wireless router on your network.
Gaming Console
Internet
D-Link DAP-1360 User Manual
Modem
Router
DAP-1360
(in Wireless Client Mode)
14
Section 2 - Installation
Repeater Mode
In Repeater mode, the DAP-1360 increases the range of your wireless network by extending the wireless coverage of another
AP or wireless router. The APs and wireless router (if used) must be within range of each other. Make sure that all clients, APs,
and the wireless router all use the same SSID (wireless network name), channel, and security settings.
Computer
Computer
Internet
Modem
Router
DAP-1360
(In Repeater Mode)
Computer
D-Link DAP-1360 User Manual
15
Section 2 - Installation
Bridge Mode
In the Bridge mode, the DAP-1360 wirelessly connects seperate local area networks (LANs) that can’t easily be connected
together with a cable. For example, if there are two wired LANs separated by a small courtyard, it would be expensive to bury
cables to connect between the two sides together. A better solution is to use two DAP-1360 units to wirelessly connect the
two LANs. In the Bridge mode, both DAP-1360 units do not act as APs.
Note: The Bridge mode is not specified in the Wi-Fi or IEEE standards. This mode will only work using two DAP-1360 units.
Communication with other APs (even other D-Link APs) is not guaranteed.
Connecting Two Separate LANs Together Through Two DAP-1360 Units
D-Link DAP-1360 User Manual
16
Section 2 - Installation
Bridge with AP Mode
The Bridge with AP mode is the same as the Bridge mode, but in this case, the DAP-1360 also acts as an AP. Clients with wireless
interfaces can wirelessly connect to the DAP-1360 and then connect to the other LAN that the DAP-1360 bridges to.
Note: The Bridge with AP mode is not specified in the Wi-Fi or IEEE standards. This mode will only work using two DAP-1360 units.
Communication with other APs (even other D-Link APs) is not guaranteed.
LAN 1
LAN 2
Computer
Computer
Computer
Computer
DAP-1360
(In Bridge Mode with AP Mode)
DAP-1360
(In Bridge Mode with AP Mode)
Connecting Two Separate LANs Together Through Two DAP-1360 Units
(Wireless PCs Can Access the DAP-1360 Units)
D-Link DAP-1360 User Manual
17
Section 2 - Installation
WISP Client Router Mode
In the WISP Client Router mode, the DAP-1360 wirelessly connects to a WISP (Wireless Internet Service Provider) AP. In this
mode, the DAP-1360 also acts as a router for wired clients on your LAN and provides NAT (Network Address Translation) and
a DHCP server to generate IP addresses for wired clients only. NAT and the DHCP server allow many computers to share the
same wireless Internet connection.
If you are a WISP subscriber and want to access your WISP account using wired computers, connect your computers to the
DAP-1360 to get NAT, and then connect them to the WISP AP.
Computer
Internet
WISP Outdoor AP
DAP-1360
(In WISP Client Mode)
Connecting Wired PCs to the Internet Using the DAP-1360
D-Link DAP-1360 User Manual
18
Section 2 - Installation
WISP Repeater Mode
In the WISP Repeater mode, the DAP-1360 wirelessly connects to a WISP (Wireless Internet Service Provider) AP. In this mode,
the DAP-1360 also acts as a router for both wireless and wired clients on your LAN. The WISP Repeater mode provides NAT
(Network Address Translation) and a DHCP server to generate IP addresses for both wireless and wired clients. NAT and the
DHCP server allow many computers to share the same wireless Internet connection.
If you are a WISP subscriber and want to use your WISP account in your house, but the signals from the outdoor WISP AP are
not strong enough to reach all of the areas in the house, use the DAP-1360 to can extend the signals from the outdoor WISP
AP and provide access to wireless clients in your house. Using this mode, wireless as well as wired clients can connect to the
outdoor WISP AP through the DAP-1360.
Computer
Computer
Internet
Modem
Router
DAP-1360
(In Repeater Mode)
Computer
Connecting Wired and Wireless PCs to the Internet Using the DAP-1360
D-Link DAP-1360 User Manual
19
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless access point lets you access your network using a wireless connection from virtually anywhere within the
operating range of your wireless network. Keep in mind, however, that the number, thickness and location of walls, ceilings,
or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary depending on the types
of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to
follow these basic guidelines:
1.Keep the number of walls and ceilings between the D-Link access point and other network devices to a minimum.
Each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that
the number of walls or ceilings is minimized.
2.Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters)
thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for
better reception.
3.Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect on
range. Try to position access points, wireless access points, and computers so that the signal passes through
drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (fish
tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
4.Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF
noise.
5.If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security
systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4GHz phone
base is as far away from your wireless devices as possible. The base transmits a signal even if the phone is not
in use.
D-Link DAP-1360 User Manual
20
Section 3 - Configuration
Configuration
This section will show you how to configure your new D-Link wireless access point using the web-based configuration utility.
Web-based Configuration Utility
If you wish to change the default settings or optimize the
performance of the DAP-1360, you may use the web-based
configuration utility.
To access the configuration utility, open a web browser
such as Internet Explorer and enter http://dlinkap or
http://192.168.0.50 in the address field.
Select Admin and then enter your password. Leave the
password blank by default.
If you get a Page Cannot be Displayed error, please refer to
the Troubleshooting section for assistance.
D-Link DAP-1360 User Manual
21
Section 3 - Configuration
Wireless Setup Wizard
Click Launch Wireless Setup Wizard to configure your
access point.
If you want to enter your settings without running the
wizard, skip to page 34.
Click Next to continue.
D-Link DAP-1360 User Manual
22
Section 3 - Configuration
Access Point Mode
This Wizard is designed to assist you in configuring your DAP-1360 as an access point.
Select Access Point from the drop-down menu. Then,
click Next to continue.
Select WPS as the configuration method only if your
wireless device supports Wi-Fi Protected Setup (WPS).
For Manual setup, skip to page 25.
Click Next to continue.
D-Link DAP-1360 User Manual
23
Section 3 - Configuration
Press down the Push Button on the Wireless device you
are adding to your wireless network.
Click Save to save your network settings.
In order for your network settings to take effect AP will
reboot automatically.
When the device has finished rebooting the main screen
will display.
D-Link DAP-1360 User Manual
24
Section 3 - Configuration
Select Manual as the configuration method to set up
your network manually.
Click Next to continue.
Enter a name for your wireless network (SSID).
Enter your network key. This key must be entered on
your wireless clients.
Click Next to continue.
The following screen will show you your network key to
enter on your wireless clients.
Click Save to finish the Setup Wizard.
D-Link DAP-1360 User Manual
25
Section 3 - Configuration
Repeater Mode
This Wizard is designed to assist you in configuring your DAP-1360 as a repeater.
Select Repeater from the drop-down menu.
Select WPS as the configuration method only if your
wireless device supports Wi-Fi Protected Setup (WPS).
For Manual setup, skip to the next page.
Click Next to continue.
On the device you want to connect to, start the PBC
process on the device. You will have 2 minutes to start
the PBC process on both devices.
D-Link DAP-1360 User Manual
26
Section 3 - Configuration
Select Manual configuration to setup your network
manually.
Click Next to continue.
Find your router or access point from the list, click the
radio button in the right column, and click Connect.
If click Key in SSID, enter the network name (SSID) of
the network you want to connect to.
D-Link DAP-1360 User Manual
27
Section 3 - Configuration
Choose which Security Mode you want to use and click
Next to continue.
If you select WEP, choose the key type (ASCII or HEX), the
key size (64 or 128-bit), and enter the wireless security
password. Click Next to complete the Setup Wizard.
If you select WPA or WPA2, enter the wireless security
password. Click Next to complete the Setup Wizard.
D-Link DAP-1360 User Manual
28
Section 3 - Configuration
If you select Auto, enter the wireless security password.
Click Next to complete the Setup Wizard.
The Wireless Setup Wizard is complete. Click Finish to
reboot the device.
D-Link DAP-1360 User Manual
29
Section 3 - Configuration
Wireless Client Mode
This Wizard is designed to assist you in configuring your DAP-1360 as a wireless client.
Select Wireless Client from the drop-down menu.
Select WPS as the configuration method only if your
wireless device supports Wi-Fi Protected Setup (WPS).
For Manual setup, skip to the next page.
Click Next to continue.
On the device you want to connect to, start the PBC
process on the device. You will have 2 minutes to start
the PBC process on both devices.
D-Link DAP-1360 User Manual
30
Section 3 - Configuration
Select Manual configuration to setup your network
manually.
Click Next to continue.
Find your access point from the list, click the radio
button in the right column, and click Connect.
If click Key in SSID, enter the network name (SSID) of
the network you want to connect to.
D-Link DAP-1360 User Manual
31
Section 3 - Configuration
Choose which Security Mode you want to use and click
Next to continue.
If you select WEP, choose the key type (ASCII or HEX), the
key size (64 or 128-bit), and enter the wireless security
password. Click Next to complete the Setup Wizard.
If you select WPA or WPA2, enter the wireless security
password. Click Next to complete the Setup Wizard.
D-Link DAP-1360 User Manual
32
Section 3 - Configuration
If you select Auto, enter the wireless security password.
Click Next to complete the Setup Wizard.
The Wireless Setup Wizard is complete. Click Finish to
reboot the device.
D-Link DAP-1360 User Manual
33
Section 3 - Configuration
Manual Configuration
Wireless Settings
You may manually configure your DAP-1360 instead of running the setup wizard.
•
•
•
•
•
•
•
Access Point mode - page 35
Repeater mode - page 37
Wireless Client mode - page 38
Bridge mode - page 39
Bridge with AP mode - page 40
WISP Client Router mode - page 41
WISP Repeater mode - page 41
D-Link DAP-1360 User Manual
34
Section 3 - Configuration
Access Point Mode
Enable Wireless: Check the box to enable the wireless function. If you
do not want to use wireless, uncheck the box to disable
all the wireless functions. You may also set up a specific
time range (schedule). Select a schedule from the dropdown menu or click Add New to create a new schedule.
Wireless Mode: Select Access Point from the drop-down menu.
Wireless When you are browsing for available wireless networks,
Network Name: this is the name that will appear in the list (unless
Visibility Status is set to Invisible, see below). This name
is also referred to as the SSID. For security purposes, it
is highly recommended to change from the default
network name.
802.11 Mode: Select one of the following:
802.11b Only - Select if you are only using 802.11b
wireless clients.
802.11g Only - Select if you are only using 802.11g
wireless clients.
802.11n Only - Select if you are only using 802.11n
wireless clients.
Mixed 802.11g and 802.11b - Select if you are using
a mix of 802.11g and 11b wireless clients.
Mixed 802.11n and 802.11g - Select if you are using
a mix of 802.11n and 11g wireless clients.
Mixed 802.11n, 802.11g and 802.11b - Select if you are using a mix of 802.11n, 11g, and 11b wireless clients.
Wireless Indicates the channel setting for the DAP-1360. The Channel can be changed to fit the channel setting for an existing wireless network
Channel: or to customize the wireless network. If you enable Auto Channel Scan, this option will be grayed out.
Enable Auto The Auto Channel Scan setting can be selected to allow the DAP-1360 to choose the channel with the least amount of interference.
Channel Scan:
D-Link DAP-1360 User Manual
35
Section 3 - Configuration
Channel Width: Select the Channel Width:
Auto 20/40 - Select if you are using both 802.11n and non-802.11n wireless devices.
20MHz - Select if you are not using any 802.11n wireless clients.
Visibility Status: Check the box if you do not want the SSID of your wireless network to be broadcasted by the DAP-1360. If checked, the SSID of the
DAP-1360 will not be seen by Site Survey utilities so your wireless clients will have to know the SSID of your DAP-1360 in order to
connect to it.
Security Mode: Refer to page 65 for more information regarding the wireless security.
D-Link DAP-1360 User Manual
36
Section 3 - Configuration
Repeater Mode
Enable Wireless: Check the box to enable the wireless function. If you do
not want to use wireless, uncheck the box to disable all
the wireless functions. You may also set up a specific time
range (schedule). Select a schedule from the drop-down
menu or click Add New to create a new schedule.
Wireless Mode: Select Repeater from the drop-down menu.
Site Survey: Click Site Survey to display a list of wireless networks
in your area. You may select the wireless access point
to connect to.
Wireless Network Enter the SSID of the access point you want to repeat the
Name: signal of. If you do not know for sure, click Site Survey
and select it from the list, if available.
802.11 Mode: Select the appropriate 802.11 mode based on the
wireless clients in your network. The drop-down menu
options are 802.11g Only, Mixed 802.11b/g, 802.11b
Only, 802.11n Only, or Mixed 802.11b/g/n.
Enable Auto The Auto Channel Scan setting can be selected to allow
Channel Scan: the DAP-1360 to choose the channel with the least
amount of interference.
Wireless Channel: The channel will automatically change to the channel of the AP you are connected to.
Channel Width: Select the appropriate channel width between 20MHz or Auto 20/40MHz from the drop-down menu.
Visibility Status: Check the box if you do not want the SSID to be broadcast by the DAP-1360. This prevents the SSID from being seen by site survey
utilities, so any wireless clients will have to be pre-configured with the SSID of the DAP-1360 in order to connect to it.
Wireless Security Select a wireless security setting. Options are None, WEP, WPA, or WPA2. See the Wireless Security section in this manual for a detailed
Mode: explanation of the wireless security options.
D-Link DAP-1360 User Manual
37
Section 3 - Configuration
Wireless Client Mode
Wireless Mode: Select Wireless Client Mode from the drop-down menu.
Site Survey:
Wireless Type: Click Site Survey to display a list of wireless networks in your
area. You may select the wireless access point to connect to.
Select Infrastructure if connecting to an access point or
wireless router, or select Ad-Hoc if connecting to another
wireless client.
Wireless Network Enter the SSID of the access point you want to repeat the signal
Name: of. If you do not know for sure, click Site Survey and select it
from the list, if available.
802.11 Mode: Select the appropriate 802.11 mode based on the wireless
clients in your network. The drop-down menu options are
802.11g Only, Mixed 802.11b/g, 802.11b Only, 802.11n
Only, or Mixed 802.11b/g/n.
Wireless Channel: The channel will automatically change to the channel of the
AP you are connected to.
Enable Auto The Auto Channel Scan setting can be selected to allow the
Channel Scan: DAP-1360 to choose the channel with the least amount of
interference.
Channel Width: Select the appropriate channel width between 20MHz or Auto
20/40MHz from the drop-down menu.
Visibility Status: Check the box if you do not want the SSID to be broadcast by the DAP-1360. This prevents the SSID from being seen by site survey
utilities, so any wireless clients will have to be pre-configured with the SSID of the DAP-1360 in order to connect to it.
Wireless MAC You can clone the wireless MAC address to connect the device.
Clone:
Wireless Security Select a wireless security setting. Options are None, WEP, WPA, or WPA2. See the Wireless Security section in this manual for a detailed
Mode: explanation of the wireless security options.
WPS: Select enable if you want to configure the DAP-1360 with Wi-Fi Protection setup.
D-Link DAP-1360 User Manual
38
Section 3 - Configuration
Bridge Mode
Enable Wireless: Select this to turn the Wi-Fi module on and off. Use the
drop-down box to select if you want to use a schedule.
Click Add New to add or change a schedule.
Wireless Mode: Select Bridge from the drop-down menu.
Wireless Network The Wireless Network Name is a unique name that
Name: identifies a network. All devices on a network must share
the same wireless network name in order to communicate
on the network. If you decide to change the wireless
network name from the default setting, enter your new
wireless network name in this field.
802.11 Mode: Select the appropriate 802.11 mode based on the wireless
clients in your network. The drop-down menu options
are 802.11g Only, Mixed 802.11b/g, 802.11b Only,
802.11n Only, or Mixed 802.11b/g/n.
Wireless Channel: All devices on the network must share the same channel.
Enable Auto The Auto Channel Scan setting can be selected to allow
Channel Scan: the DAP-1360 to choose the channel with the least
amount of interference.
Channel Width: Select the appropriate channel width between 20MHz
or Auto 20/40MHz from the drop-down menu.
Visibility Status: Select the transmission rate. It is strongly suggested to use the Auto setting for optimal performance.
Remote AP MAC: Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks.
Bridge Security: Select None to disable encryption to across the network. Select WEP 64-bit or WEP 128-bit to limit communication to only those
devices that share the same WEP settings. Select WPA-PSK or WPA2-PSK to secure your network using a password and dynamic key
changes (No RADIUS server required).
Note: The Bridge mode is not completely specified in the Wi-Fi or IEEE standards. This mode can work with other DAP-1360 units. Communication with
other APs (even other D-Link APs) is not guaranteed.
D-Link DAP-1360 User Manual
39
Section 3 - Configuration
Bridge with AP Mode
Enable Wireless: Select this to turn the Wi-Fi module on and off. Use the
drop-down box to select if you want to use a schedule.
Click Add New to add or change a schedule.
Wireless Mode: Select Bridge with AP from the drop-down menu.
Wireless Network The Wireless Network Name is a unique name that
Name: identifies a network. All devices on a network must
share the same wireless network name in order to
communicate on the network. If you decide to change
the wireless network name from the default setting,
enter your new wireless network name in this field.
802.11 Mode: Select the appropriate 802.11 mode based on the
wireless clients in your network. The drop-down menu
options are 802.11g Only, Mixed 802.11b/g, 802.11b
Only, 802.11n Only, or Mixed 802.11b/g/n.
Wireless Channel: All devices on the network must share the same channel.
Enable Auto Scan: The Auto Channel Scan setting can be selected to allow
the DAP-1360 to choose the channel with the least
amount of interference.
Channel Width: Select the appropriate channel width between 20MHz
or Auto 20/40MHz from the drop-down menu.
Visibility Status: Check the box if you do not want the SSID to be broadcast by the DAP-1360. This prevents the SSID from being seen by site survey
utilities, so any wireless clients will have to be pre-configured with the SSID of the DAP-1360 in order to connect to it.
Remote AP MAC: Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks.
Bridge Security: Select None to disable encryption to across the network. Select WEP 64-bits or WEP 128-bits to limit communication to only those
devices that share the same WEP settings. Select WPA-PSK or WPA2-PSK to secure your network using a password and dynamic key
changes (No RADIUS server required).
Note: The Bridge with AP mode is not completely specified in the Wi-Fi or IEEE standards. This mode can work with other DAP-1360 units. Communication with other APs (even other
D-Link APs) is not guaranteed.
D-Link DAP-1360 User Manual
40
Section 3 - Configuration
WISP Client Router/WISP Repeater Modes
Enable Wireless: Select this to turn the Wi-Fi module on and off.
Use the drop-down box to select if you want to
use a schedule. Click Add New to add or change
a schedule.
Wireless Mode: Select WISP Client or WISP Repeater from the
drop-down menu.
Site Survey: Click this button to choose the root AP from an
available connection list. If the root AP has wireless
encryption, you have to use the same wireless
security mode to connect the root AP.
Wireless Network You can input the wireless network name of the
Name: root AP or click the Site Survey button to find the
root AP.
802.11 Mode: Select the appropriate 802.11 mode based
on the wireless clients in your network. The
drop-down menu options are 802.11g Only, Mixed
802.11b/g, 802.11b Only, 802.11n Only, or Mixed
802.11b/g/n.
Wireless Channel: The channel used will be displayed. The channel
will follow the root AP.
Enable Auto Scan: The Auto Channel Scan setting can be selected to allow the DAP-1360 to choose the channel with the least amount of interference.
Channel Width: Select the appropriate channel width between 20MHz or Auto 20/40MHz from the drop-down menu.
Visibility Status: Check the box if you do not want the SSID to be broadcast by the DAP-1360. This prevents the SSID from being seen by site survey
utilities, so any wireless clients will have to be pre-configured with the SSID of the DAP-1360 in order to connect to it.
Wireless Security Select a wireless security setting. Options are None, WEP, WPA, or WPA2. Refer to the Wireless Security section of this manual for
Mode: a detailed explanation of the wireless security options.
D-Link DAP-1360 User Manual
41
Section 3 - Configuration
WAN Settings
Dynamic IP (DHCP)
WAN settings are only used in the WISP Client Router wireless mode and the WISP Repeater wireless mode. Choose Dynamic
IP(DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP
number to use. This option is commonly used for Cable modem services.
Host Name: The Host Name is optional but may be required
by some ISPs.
MTU Size: You may need to change the MTU (Maximum
Transmission Unit) for optimal performance
with your specific ISP. The default MTU size is
1500.
Attain DNS Select this option if you want the DAP-1360 to
Automatically: get the DNS (Domain Name System) server IP
address automatically.
Set DNS manually: Select this option if you want to manually enter
the DNS Server IP address(es). The fields to
enter the Primary and Secondary DNS server
IP addresses will appear after you have selected this option.
DNS Server: Enter the Primary and Secondary DNS server IP address assigned by your ISP.
Clone MAC Address: The default MAC address is set to the Ethernet MAC address your DAP-1360. You can click the Clone Your PC’s MAC Address button
to replace the AP’s MAC address with the MAC address of the PC that you used to register with your ISP. It is not recommended
that you change the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
42
Section 3 - Configuration
Static IP
Select Static IP if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask,
gateway address, and DNS address(es) provided to you by your ISP.
IP Address: 192.168.1.1 is the default WAN IP Address of
the DAP-1360.
Subnet Mask: 255.255.255.0 is the default subnet mask.
All devices on the network must have the
same subnet mask to communicate on the
network.
Default Gateway: Enter the IP Address of the gateway in your
network.
MTU Size: You may need to change the MTU (Maximum
Transmission Unit) for optimal performance
with your specific ISP. The default MTU size
is 1500.
Primary DNS Server: Enter the Primary DNS (Domain Name
System) server IP address assigned by your
ISP.
Secondary DNS Server: Enter the Secondary DNS (optional) server IP address assigned by your ISP.
Clone MAC Address: The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your PC’s MAC Address
button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change
the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
43
Section 3 - Configuration
PPPoE
Select PPPoE (Point-to-Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your
computer. The software is no longer needed and will not work through the DAP-1360.
Username: Enter your PPPoE user name.
Password: Enter your PPPoE password and then retype the
password in the next box.
Service Name: Enter the ISP Service Name (optional).
Reconnection Type: Select Always on, On demand, or Manual.
Maximum Idle Time: Enter a maximum idle time during which the
Internet connection is maintained during inactivity.
MTU Size: You may need to change the MTU (Maximum
Transmission Unit) for optimal performance with
your specific ISP. The maximum/default MTU size
is 1492.
Attain Select this option if you want the DAP-1360 to get
DNS Automatically: the DNS (Domain Name System) server IP address
automatically.
Set DNS Manually: Select this option if you want to manually enter
the DNS Server IP address(es). Fields to enter the
Primary and Secondary DNS server IP addresses will appear after you select this option.
DNS Servers: Enter the Primary and Secondary DNS server IP address assigned by your ISP.
Clone MAC Address: The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your PC’s MAC Address
button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change
the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
44
Section 3 - Configuration
PPTP
Choose PPTP (Point-to-Point Tunneling Protocol) if your ISP uses a PPTP connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services.
PPTP IP Address: Enter the IP address (Static PPTP only).
PPTP Subnet Mask: Enter the subnet mask.
PPTP Server IP Address: Enter the Server IP Address provided by your
ISP.
Username: Enter your PPTP username.
Password: Enter your PPTP password and then retype
the password in the next box.
MTU Size: You may need to change the MTU (Maximum
Transmission Unit) for optimal performance
with your specific ISP. The default MTU size
is 1400.
Attain Select this option if you want the DAP-1360
DNS Automarically: get DNS server IP address automatically.
Set DNS Automatically: Select this option if you want to manually
enter the DNS Server IP address(es). Fields to
enter the Primary and Secondary DNS server
IP addresses will appear after you select this
option.
DNS Servers: Enter the Primary and Secondary DNS (Domain Name System) server IP address assigned by your ISP.
Clone MAC Address: The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your PC’s MAC Address
button to replace the AP’s MAC address with the MAC address of your Ethernet card. It is not recommended that you change
the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
45
Section 3 - Configuration
LAN Settings
This section will allow you to change the local network settings of the access point and to configure the DHCP settings.
Device Name: Enter the Device Name of the AP. It is recommended
to change the Device Name if there is more than
one D-Link device within the subnet.
LAN Connection Use the drop-down menu to select Dynamic IP
Type: (DHCP) to automatically obtain an IP address on
the LAN/private network.
My IPv6 Select from the drop-down menu the type of IPv6
Connection Type: connection you would like to use.
D-Link DAP-1360 User Manual
46
Section 3 - Configuration
Static IP
Select Static IP Address if all the Internet port’s IP information is provided to you by your ISP. You will need to enter in the IP
address, subnet mask, gateway address, and DNS address(es) provided to you by your ISP. Each IP address entered in the fields
must be in the appropriate IP form, which are four octets separated by a dot (x.x.x.x). The Access point will not accept the IP
address if it is not in this format.
Device Name: Enter the Device Name of the AP. It is
recommended to change the Device Name if
there is more than one D-Link device within the
subnet. You can enter the device name of the
AP into your web browser to access the instead
of IP address for configuration. If you are using
the device name to connect, ensure that your
PC and your DAP-1360 are on the same network.
LAN Connection Type: Select Static IP from the drop-down menu.
IP Address: Enter the IP address of the access point. The
default IP address is 192.168.0.50. If you change
the IP address, once you click Apply, you will
need to enter the new IP address in your browser
to get back into the configuration utility.
Subnet Mask: Enter the Subnet Mask assigned by your ISP.
Default Gateway: Enter the Gateway assigned by your ISP.
D-Link DAP-1360 User Manual
47
Section 3 - Configuration
Advanced
Advanced Wireless
Transmit Power: Sets the transmit power of the antennas.
WMM Enable: WMM is QoS for your wireless network. This will
improve the quality of video and voice applications
for your wireless clients.
Short GI: Check this box to reduce the guard interval time
therefore increasing the data capacity. However,
it’s less reliable and may create higher data loss.
IGMP Snooping: This enables IGMP snooping for the wireless
connection. We recommend enabling this if
you often use multicast services such as video
conferencing and streaming audio/video.
WLAN Partition: This feature enables client isolation. If enabling,
all clients will not be able to view or access each
other’s information or within the network.
HT 20/40 Check to enable or disable this feature.
Coexistance:
D-Link DAP-1360 User Manual
48
Section 3 - Configuration
MAC Address Filter
The MAC address filter section can be used to filter network access by machines based on the unique MAC addresses of their
network adapter(s). It is most useful to prevent unauthorized wireless devices from connecting to your network. A MAC address
is a unique ID assigned by the manufacturer of the network adapter.
Configure When Turn MAC Filtering OFF is selected, MAC addresses
MAC Filtering: are not used to control network access. When Turn MAC
Filtering ON and ALLOW computers listed to access the
network is selected, only computers with MAC addresses
listed in the MAC Address List are granted network access.
When Turn MAC Filtering ON and DENY computers listed
to access the network is selected, any computer with a
MAC address listed in the MAC Address List is refused access
to the network.
Add MAC This parameter allows you to manually add a MAC filtering
Filtering rule. Click the Add button to add the new MAC filtering rule
Rule: to the MAC Filtering Rules list at the bottom of this screen.
D-Link DAP-1360 User Manual
49
Section 3 - Configuration
Wi-Fi Protected Setup
Wi-Fi Protected Setup (WPS) System is a simplified method for securing your wireless network during the “Initial setup” as well
as the “Add New Device” processes. The Wi-Fi Alliance (WFA) has certified it across different products as well as manufactures.
The process is just as easy, as depressing a button for the Push-Button Method or correctly entering the 8-digit code for the
Pin-Code Method. The time reduction in setup and ease of use are quite beneficial, while the highest wireless Security setting
of WPA2 is automatically used.
Enable: Check this box to enable the function
Lock Wireless Locking the wireless security settings prevents the
Security Settings: settings from being changed by the Wi-Fi Protected
Setup feature of the router. Devices can still be added
to the network using Wi-Fi Protected Setup. However,
the settings of the network will not change once this
option is checked.
Pin Settings: Press the button to generate a new PIN or Reset to
Default.
Current PIN: Shows the current value of the router’s PIN.
Reset PIN to Restore the default PIN of the access point.
Default:
Generate New Create a random number that is a valid PIN. This
PIN: becomes the router’s PIN. You can then copy this PIN
to the user interface of the registrar.
Add Wireless Press the button to start with the wizard to setup
Station: the WPS.
D-Link DAP-1360 User Manual
50
Section 3 - Configuration
User Limits
Enter the maximum number of wireless clients that can connect at one time to your access point.
Enable User Check the Enable User Limit box to enable this
Limit: feature.
User Limit: Enter the maximum number of clients, between 1
and 32.
Save Click Save Settings to save and activate the new
Settings: changes.
D-Link DAP-1360 User Manual
51
Section 3 - Configuration
Port Forwarding (WISP modes only)
This function is available if your DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to open
a single port or a range of ports. Click Save Settings and the port forwarding rule will be put into the Port Forwarding List.
Port Forwarding Check the box to configure a port forwarding rule.
Rules:
Name: Enter a name for the rule. You can select an
application name from the Application Name dropdown menu. Click the << button to fill in the Name
field with the application name that you selected.
IP Address: Enter the IP address of the computer on your local
network that you want to allow the incoming
service to.
Start/End Ports: Enter the port or ports that you want to open. If
you want to open one port, enter the same port in
both boxes.
Traffic Type: Select TCP, UDP, or Both.
D-Link DAP-1360 User Manual
52
Section 3 - Configuration
Port Filter (WISP modes only)
This function is available if your DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature is used to secure
or restrict your local network. It will deny the ports that you enter from the local network to the Internet. Click Save Settings
and the port filter rule will be put into the Port Filter List.
Port Filter Check the box to configure a port filter rule.
Rules:
Name: Enter a name for the rule. You can select an
application name from the Application Name dropdown menu. Click the << button to fill in the Name
field with the application name that you selected.
Start/End Ports: Enter the port or ports that you want to open. If
you want to open one port, enter the same port in
both boxes. Traffic Type: Select TCP, UDP, or Both.
D-Link DAP-1360 User Manual
53
Section 3 - Configuration
DMZ (WISP modes only)
This function is available only if the DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to
set up a DMZ (Demilitarized Zone) host. If you have a client PC that cannot run Internet applications properly from behind the
DAP-1360, then you can set the client up for unrestricted Internet access. The DMZ allows a computer to be exposed to the
Internet. This feature is useful for gaming purposes. Enter the IP address of the computer that will be the DMZ host. Adding a
client to the DMZ may expose your local network to a variety of security risks, so only use this option as a last resort.
Enable DMZ: Check this box to enable DMZ.
DMZ Host IP Enter the IP address of the computer you would
Address: like to open all ports to. You can select a computer
from the Computer Name drop-down menu and
click << to enter the computer name into the DMZ
Host IP Address field.
D-Link DAP-1360 User Manual
54
Section 3 - Configuration
Parental Control (WISP modes only)
This function is available only if the DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to
create a list of websites that you want to deny users access.
Configure Select Turn Website Filtering OFF or Turn Website
Website Filtering ON and DENY computers access to
Filtering Below: ONLY these sites.
Website URL Enter a keyword or URL that you want to block
Address: and click Save Settings. Any URL that contains the
keyword will be blocked.
D-Link DAP-1360 User Manual
55
Section 3 - Configuration
Advanced Network (WISP modes only)
This function is available if the DAP-1360 is in WISP Client Router or WISP Repeater mode. This feature allows you to change
the LAN settings. Please be aware that any changes to the factory default settings may affect the behavior of your network.
Enable UPnP: Check this box to use the Universal Plug and Play
(UPnP™) feature. UPnP provides compatibility with
networking equipment, software and peripherals.
Enable WAN Ping Check this box to allow the WAN port of the
Respond: DAP-1360 to be pinged. Unchecking the box
will not allow the DAP-1360 to respond to pings.
Blocking ping response may provide some extra
security from intruders.
Remote Remote management allows the DAP-1360 to be
Management: configured from the Internet by a web browser. A
username and password are still required to access
the Web-Management interface. In general, only a
member of your network can browse the built-in
web pages to perform Administrator tasks. This
feature enables you to perform Administrator
tasks from the remote (Internet) host.
D-Link DAP-1360 User Manual
56
Section 3 - Configuration
Maintenance
Admin
This page will allow you to change the Administrator password. The administrator password has read/write access.
Password: Enter a new password for the Administrator Login
Name. The administrator can make changes to the
settings.
Confirm Enter the same password that you entered in the
Password: previous textbox in order to confirm its accuracy.
Enable Check to enable this feature.
Graphical
Authentication:
D-Link DAP-1360 User Manual
57
Section 3 - Configuration
System
Save to Local Use this option to save the current access point
Hard Drive: configuration settings to a file on the hard disk of the
computer you are using. Click the Save button. You will
then see a file dialog where you can select a location
and file name for the settings.
Upload from Use this option to load previously saved access
Local Hard Drive: point configuration settings. Click Browse to find a
previously saved configuration file. Then, click the
Upload Settings button to transfer those settings to
the access point.
Restore to This option will restore all configuration settings back
Factory Default: to the settings that were in effect at the time the access
point was shipped from the factory. Any settings that
have not been saved will be lost, including any rules
that you have created. If you want to save the current
access point configuration settings, use the Save
button above.
Note: Restoring the factory default settings will not reset
the Wi-Fi Protected Status to Not Configured.
Reboot the Click to reboot the access point.
Device:
D-Link DAP-1360 User Manual
58
Section 3 - Configuration
Firmware
You can upgrade the firmware of the access point here. Make sure the firmware you want to use is on the local hard drive of
the computer. Click on Browse to locate the firmware file to be used for the update. Please check the D-Link support website
for firmware updates at http://support.dlink.com. You can download firmware upgrades to your hard drive from this site.
Firmware Click on Check Now to find out if there is an updated
Upgrade: firmware; if so, download the new firmware to your
hard drive.
Browse: After you have downloaded the new firmware, click
Browse to locate the firmware update on your hard
drive. Click Upload to complete the firmware upgrade.
Upload: Once you have a firmware update on your computer,
use this option to browse for the file and then upload
the information into the access point.
Language Pack
You can change the language of the web UI by uploading
available language packs.
Browse: After you have downloaded the new language pack,
click Browse to locate the language pack file on your
hard drive. Click Upload to complete the language
pack upgrade.
D-Link DAP-1360 User Manual
59
Section 3 - Configuration
Watchdog
The Watchdog feature pings a specified IP address. If the IP address stops responding to pings, your AP will be rebooted. You
can also select an option to have the DAP-1360 send an e-mail alert if the specified IP address stops responding to pings.
Enable Watchdog Check this box to enable the Watchdog (Ping
(Ping of Life): of Life) to check some host IP.
Update Time Enter the time interval of how often you would
Interval: like the Watchdog to ping the response IP
address.
Watchdog Response Enter the IP address that the Watchdog will
IP: ping.
Enable Mail Alert: Check this box to enable e-mail notification for
the Watchdog.
SMTP Server: Enter the SMTP server IP address.
Sender E-Mail: Enter the e-mail address from which the
notification will be sent.
Receiver E-Mail: Enter the e-mail address which the notification
will be sent to.
Enable Check the box to enable authentication that is used with the SMTP server.
Authentication:
Account Name: Enter your account name that is used with the SMTP server.
Password: Enter your password that is used with the SMTP server and re-enter it in the next box.
D-Link DAP-1360 User Manual
60
Section 3 - Configuration
Time
The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock.
From this section you can set the time zone that you are in. Daylight Saving can also be configured to automatically adjust the
time when needed.
Time Zone: Select the Time Zone from the drop-down menu.
Daylight Saving: To select Daylight Saving time manually, click the
Enable Daylight Saving check box. Next use the
drop-down menu to select a Daylight Saving Offset
and then enter a start date and an end date for
daylight saving time.
Enable NTP Server: NTP is short for Network Time Protocol. NTP
synchronizes computer clock times in a network
of computers. Check this box to use a NTP server.
This will only connect to a server on the Internet,
not a local server.
NTP Server Used: Enter the NTP server or select one from the dropdown menu.
Date and Time: To manually input the time, enter the values in
these fields for the Year, Month, Day, Hour, Minute,
and Second and then click Save Settings. You
can also click the Copy Your Computer’s Time
Settings button at the bottom of the screen.
D-Link DAP-1360 User Manual
61
Section 3 - Configuration
System Check
This section Ping Tests by sending ping packets to test if a computer on the internet is running and responding.
Ping Test / The Ping Test / IPv6 Ping Test is used to send Ping
IPv6 Ping Test: packets to test if a computer is on the Internet.
Enter the host name or IP/IPv6 address that you
wish to Ping, and click Ping.
Ping Result: The results of your ping attempts will be displayed
here.
D-Link DAP-1360 User Manual
62
Section 3 - Configuration
Schedules
Name: Enter a name for your new schedule.
Days: Select a day, a range of days, or All Week to
include every day.
Time: Enter a start and end time for your schedule.
Schedule Rules The list of schedules will be listed here. Click the
List: Edit icon to make changes or click the Delete
icon to remove the schedule.
D-Link DAP-1360 User Manual
63
Section 3 - Configuration
Status
Device Info
This page displays the current information for the DAP-1360. It will display the LAN and wireless LAN information.
General: Displays the access point’s time and firmware
version.
LAN: Displays the MAC address and the private (local) IP
settings for the access point.
Wireless LAN: Displays the wireless MAC address and your
wireless settings such as SSID and Channel.
D-Link DAP-1360 User Manual
64
Section 3 - Configuration
Logs
The DAP-1360 keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are automatically
cleared. You can save the log files under Log Setting.
Log Options: There are several types of logs that can be viewed:
System Activity, Debug Information, Attacks,
Dropped Packets and Notice.
First Page: This button directs you to the first page of the log.
Last Page: This button directs you to the last page of the log.
Previous Page: This button directs you to the previous page of the log.
Next Page: This button directs you to the next page of the log.
Clear Log: This button clears all current log content.
Log Settings: This button opens a new menu where you can
configure the log settings.
Refresh: This button refreshes the log.
D-Link DAP-1360 User Manual
65
Section 3 - Configuration
Statistics
The DAP-1360 keeps statistics of the traffic that passes through it. You can view the amount of packets that pass through the LAN
and wireless portions of the network. The traffic counter will reset if the access point is rebooted.
D-Link DAP-1360 User Manual
66
Section 3 - Configuration
Wireless
The wireless section allows you to view the wireless clients that are connected to your wireless access point.
Connection Time: Displays the amount of time the wireless client has
been connected to the access point.
MAC Address: The Ethernet ID (MAC address) of the wireless client.
D-Link DAP-1360 User Manual
67
Section 3 - Configuration
IPv6
This page displays all your IPv6 internet and network
connection information.
D-Link DAP-1360 User Manual
68
Section 3 - Configuration
Help
D-Link DAP-1360 User Manual
69
Section 4 - Security
Wireless Security
This section will show you the different levels of security you can use to protect your data from intruders. The DAP-1360 offers
the following types of security:
• WPA2 (Wi-Fi Protected Access 2) • WPA (Wi-Fi Protected Access) D-Link DAP-1360 User Manual
• WPA2-PSK (Pre-Shared Key)
• WPA-PSK (Pre-Shared Key)
70
Section 4 - Security
What is WPA?
WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent
Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a
hashing algorithm and, by adding an integrity-checking feature, ensures that the keys haven’t been tampered
with. WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP).
WEP regulates access to a wireless network based on a computer’s hardware-specific MAC address, which is
relatively simple to be sniffed out and stolen. EAP is built on a more secure public-key encryption system to
ensure that only authorized network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password
between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key
entered on your wireless bridge or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more
secure public key encryption system to ensure that only authorized network users can access the network.
D-Link DAP-1360 User Manual
71
Section 4 - Security
Configure WPA/WPA2 Personal
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the
added overhead.
1.Log into the web-based configuration by opening a web browser
and entering the IP address of the access point (192.168.0.50). Click
on Setup and then click Wireless Settings on the left side.
2.Next to Security Mode, select Enable WPA Wireless Security,
Enable WPA2 Wireless Security, or Enable WPA2-Auto Wireless
Security.
3.Next to Cipher Type, select TKIP, AES, or Auto.
4.Next to PSK / EAP, select Personal.
5.Next to Passphrase, enter a key. The key is entered as a passphrase in ASCII format at both ends of the wireless connection.
The passphrase must be between 8-63 characters.
6.Click Save Settings at the top of the window to save your settings. If you are configuring the access point with a wireless
adapter, you will lose connectivity until you enable WPA-PSK on your adapter and enter the same passphrase as you did on
the access point.
D-Link DAP-1360 User Manual
72
Section 4 - Security
Configure WPA/WPA2 Enterprise
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please establish
wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption due to the
added overhead.
1.Log into the web-based configuration by opening a web browser
and entering the IP address of the access point (192.168.0.50). Click
on Setup and then click Wireless Settings on the left side.
2.Next to Security Mode, select Enable WPA Wireless Security, Enable
WPA2 Wireless Security, or Enable WPA2-Auto Wireless Security.
3.Next to Cipher Mode, select TKIP, AES, or Auto.
4.Next to Personal / Enterprise, select Enterprise.
5. Next to RADIUS Server, enter the IP Address of your RADIUS server.
6. Next to Port, enter the port you are using with your RADIUS server.
1812 is the default port.
7. Next to Shared Secret, enter the security key.
8. Click Save Settings to save your settings.
D-Link DAP-1360 User Manual
73
Section 5 - Connecting to a Wireless Network
Connect to a Wireless Network
Using Windows® XP
Windows® XP users may use the built-in wireless utility (Zero Configuration Utility). The following instructions are for Service
Pack 2 users. If you are using another company’s utility or Windows® 2000, please refer to the user manual of your wireless
adapter for help with connecting to a wireless network. Most utilities will have a “site survey” option similar to the Windows®
XP utility as seen below.
If you receive the Wireless Networks Detected bubble, click on
the center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray
(lower-right corner next to the time). Select View Available
Wireless Networks.
The utility will display any available wireless networks in your area.
Click on a network (displayed using the SSID) and click the Connect
button.
If you get a good signal, but cannot access the Internet, check you
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
D-Link DAP-1360 User Manual
74
Section 5 - Connecting to a Wireless Network
Configure WPA-PSK
It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter. If you are
joining an existing network, you will need to know the WEP key being used.
1.Open the Windows® XP Wireless Utility by right-clicking
on the wireless computer icon in your system tray
(lower-right corner of screen). Select View Available Wireless
Networks.
2.Highlight the wireless network (SSID) you would like to
connect to and click Connect.
D-Link DAP-1360 User Manual
75
Section 5 - Connecting to a Wireless Network
3.The Wireless Network Connection box will appear. Enter the WPA-PSK
passphrase and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WPA-PSK settings are correct. The
WPA-PSK passphrase must be exactly the same as on the wireless access
point.
D-Link DAP-1360 User Manual
76
Section 5 - Connecting to a Wireless Network
Using Windows Vista®
Windows Vista® users may use the convenient, built-in wireless utility. Follow these instructions:
From the Start menu, go to Control Panel, and then click on
Network and Sharing Center.
The utility will display any available wireless networks in your
area. Click on a network (displayed using the SSID) under Select a
network to connect to and then click the Connect button.
D-Link DAP-1360 User Manual
77
Section 5 - Connecting to a Wireless Network
Click Connect Anyway to continue.
The utility will display the following window to indicate a
connection is being made.
The final window indicates the establishment of a successful
connection.
The next two pages display the windows used to connect to either
a WEP or a WPA-PSK wireless network.
D-Link DAP-1360 User Manual
78
Section 5 - Connecting to a Wireless Network
Configure WPA-PSK
It is recommended to enable WEP on your wireless bridge or access point before configuring your wireless adapter. If you are
joining an existing network, you will need to know the WEP key being used.
Click on a network (displayed using the SSID) using WPA-PSK under
Select a network to connect to and then click the Connect button.
Enter the appropriate security key or passphrase in the field
provided and then click the Connect button.
D-Link DAP-1360 User Manual
79
Section 5 - Connecting to a Wireless Network
Using Windows® 7
It is recommended to enable wireless security (WPA/WPA2) on your wireless router or access point before configuring your
wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1.Click on the wireless icon in your system tray (lower-right corner).
Wireless Icon
2.The utility will display any available wireless networks in your area.
D-Link DAP-1360 User Manual
80
Section 5 - Connecting to a Wireless Network
3.Highlight the wireless network (SSID) you would like to connect to
and click the Connect button.
If you get a good signal but cannot access the Internet, check your
TCP/IP settings for your wireless adapter. Refer to the Networking
Basics section in this manual for more information.
4.The following window appears while your computer tries to
connect to the router.
D-Link DAP-1360 User Manual
81
Section 5 - Connecting to a Wireless Network
5.Enter the same security key or passphrase that is on your router
and click Connect. You can also connect by pushing the WPS
button on the router.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct.
The key or passphrase must be exactly the same as on the wireless
router.
D-Link DAP-1360 User Manual
82
Section 5 - Connecting to a Wireless Network
Configure WPS
The WPS feature of the DAP-1360 can be configured using Windows® 7. Carry out the following steps to use Windows® 7 to
configure the WPS feature of the DAP-1360:
1.Click the Start button and select Computer from the Start
menu.
2.Click the Network option.
D-Link DAP-1360 User Manual
83
Section 5 - Connecting to a Wireless Network
3.Double-click the DAP-1360.
4.Input the WPS PIN number (displayed in the WPS window on the
Router’s LCD screen or in the Setup > Wireless Setup menu in
the Router’s Web UI) and click Next.
D-Link DAP-1360 User Manual
84
Section 5 - Connecting to a Wireless Network
5.Type a name to identify the network.
6.To configure advanced settings, click the icon.
Click Next to continue.
D-Link DAP-1360 User Manual
85
Section 5 - Connecting to a Wireless Network
7.The following window appears while the Router is being
configured.
Wait for the configuration to complete.
8.The following window informs you that WPS on the DAP-1360 has
been setup successfully.
Make a note of the security key as you may need to provide this
security key if adding an older wireless device to the network in
the future.
9.Click Close to complete WPS setup.
D-Link DAP-1360 User Manual
86
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1360. Read the
following descriptions if you are having problems. (The examples below are illustrated in Windows® XP. If you have a different
operating system, the screenshots on your computer will look similar to the following examples.)
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link access point (192.168.0.50 for example), you are not connecting to a website on
the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your
computer must be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
- Microsoft Internet Explorer® 6.0 and higher
- Mozilla Firefox 3.0 and higher
- Google™ Chrome 2.0 and higher
- Apple Safari 3.0 and higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a different
cable or connect to a different port on the device if possible. If the computer is turned off, the link light may not be on.
• Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice, Sygate,
Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the help files included
with your firewall software for more information on disabling or configuring it.
D-Link DAP-1360 User Manual
87
Section 6 - Troubleshooting
• Configure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click
the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
• Access the web management. Open your web browser and enter the IP address of your D-Link access point in the address
bar. This should open the login page for your the web management.
• If you still cannot access the configuration, unplug the power to the access point for 10 seconds and plug back in. Wait about
30 seconds and try accessing the configuration. If you have multiple computers, try connecting using a different computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your access point. Unfortunately this process will change all your settings back to
the factory defaults.
To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered on, use a
paperclip to hold the button down for 10 seconds. Release the button and the access point will go through its reboot process.
Wait about 30 seconds to access the access point. The default IP address is 192.168.0.50. When logging in, the username is
Admin and leave the password box empty.
D-Link DAP-1360 User Manual
88
Section 6 - Troubleshooting
3. Why can’t I connect to certain sites or send and receive emails when connecting through my access point?
If you are having a problem sending or receiving email, or connecting to secure sites such as eBay, banking sites, and Hotmail,
we suggest lowering the MTU in increments of ten (Ex. 1492, 1482, 1472, etc).
Note: AOL DSL+ users must use MTU of 1400.
To find the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be
another computer, or a URL.
• Click on Start and then click Run.
• Windows® 95, 98, and Me users type in command (Windows® NT, 2000, and XP users type in cmd) and press Enter
(or click OK).
• Once the window opens, you’ll need to do a special ping. Use the following syntax:
ping [url] [-f ] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472
D-Link DAP-1360 User Manual
89
Section 6 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented
packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the
proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Once you find your MTU, you can now configure your access point with the proper MTU size.
To change the MTU rate on your access point follow the steps below:
• Open your browser, enter the IP address of your access point (192.168.0.50) and click OK.
• Enter your username (Admin) and password (blank by default). Click OK to enter the web configuration page
for the device.
• Click on Setup and then click Manual Configure.
• To change the MTU enter the number in the MTU field and click Save Settings to save your settings.
• Test your email. If changing the MTU does not resolve the problem, continue changing the MTU in increments
of ten.
D-Link DAP-1360 User Manual
90
Appendix A - Wireless Basics
Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless
connectivity within your home, business or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link
wireless family of products will allow you to securely access the data you want, when and where you want it. You will be able
to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead of
wires. Wireless LANs are used increasingly in both home and office environments, and public areas such as airports, coffee shops
and universities. Innovative ways to utilize WLAN technology are helping people to work and communicate more efficiently.
Increased mobility and the absence of cabling and other fixed infrastructure have proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop
systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order
to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Access point is a device used to
provide this link.
D-Link DAP-1360 User Manual
91
Appendix A - Wireless Basics
What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio
frequency to connect wirelessly, so you have the freedom to connect computers anywhere in your home or office.
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link
delivers the performance you need at a price you can afford. D-Link has all the products you need to build your network.
How does wireless work?
Wireless works similar to how cordless phone work, through radio signals to transmit data from one point A to point B. But
wireless technology has restrictions as to how you can access the network. You must be within the wireless network range area
to be able to connect your computer. There are two different types of wireless networks Wireless Local Area Network (WLAN),
and Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point has
a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access point
as seen in the picture, the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles
to serve places like manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and
many other outdoor venues.
D-Link DAP-1360 User Manual
92
Appendix A - Wireless Basics
Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to
30 feet away.
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as
much power which makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other
devices that operate on batteries.
Who uses wireless?
Wireless technology has become so popular in recent years that almost everyone is using it, whether it’s for home, office,
business, D-Link has a wireless solution for it.
Home
• Gives everyone at home broadband access
• Surf the web, check email, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Office and Home Office
• Stay on top of everything at home as you would at office
• Remotely access your office network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate office space
D-Link DAP-1360 User Manual
93
Appendix A - Wireless Basics
Where is wireless used?
Wireless technology is expanding everywhere not just at home or office. People like the freedom of mobility and it’s becoming
so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public
places is usually called “hotspots”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote locations
like: Airports, Hotels, Coffee Shops, Libraries, Restaurants, and Convention Centers.
Wireless network is easy to setup, but if you’re installing it for the first time it could be quite a task not knowing where to start.
That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your access point or Access Point
Make sure you place the bridge/access point in a centralized location within your network for the best performance. Try to
place the bridge/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have
a two-story home, you may need a repeater to boost the signal to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, wireless speakers, and televisions as far away as possible from
the bridge/access point. This would significantly reduce any interference that the appliances might cause since they operate
on same frequency.
D-Link DAP-1360 User Manual
94
Appendix A - Wireless Basics
Security
Don’t let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning
on the WPA or WEP security feature on the access point. Refer to product manual for detail information on how to set it up.
Wireless Modes
There are basically two modes of networking:
•Infrastructure – All wireless clients will connect to an access point or wireless bridge.
•Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless network
adapters on each computer, such as two or more wireless network Cardbus adapters.
An Infrastructure network contains an Access Point or wireless bridge. All the wireless devices, or clients, will connect to the
wireless bridge or access point.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc
mode to communicate.
D-Link DAP-1360 User Manual
95
Appendix B - Networking Basics
Networking Basics
Check your IP address
After you install your adapter, by default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e.
wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK. (Windows® 7/Vista® users type cmd in the Start Search box.)
At the prompt, type ipconfig and press Enter.
This will display the IP address, subnet mask, and the
default gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation,
security settings, and the settings on your router.
Some firewall software programs may block a DHCP
request on newly installed adapters.
D-Link DAP-1360 User Manual
96
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® 7 -
Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Change Adapter
Setting.
Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network
Connections.
®
Windows XP - Click on Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet
as your network or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X
where X is a number between 2 and 99. Make sure that the number you choose is not in
use on the network. Set Default Gateway the same as the LAN IP address of your router
(192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
D-Link DAP-1360 User Manual
97
Appendix C - Technical Specifications
Technical Specifications
Standards
• IEEE 802.11n
• IEEE 802.11g
• IEEE 802.11b
• IEEE 802.3
• IEEE 802.3u
Security
• WPA-Personal
• WPA2-Personal
• WPA-Enterprise
• WPA2-Enterprise
Wireless Signal Rates1
• 300Mbps • 108Mbps
• 54Mbps
• 48Mbps
• 36Mbps
• 24Mbps
• 18Mbps • 12Mbps
• 11Mbps • 9Mbps
• 6Mbps • 5.5Mbps
• 2Mbps
• 1Mbps
Maximum Operating Voltage
• 5V 1A
Maximum Operating Current
• 450 mA
Modulation
• DQPSK
• DBPSK
• CCK
• OFDM
Frequency Range2
• 2.4GHz to 2.483GHz
LEDs
• Power • Security
• Wireless
• LAN
Operating Temperature
• 32°F to 131°F ( 0°C to 55°C)
Humidity
• 90% maximum (non-condensing)
Safety & Emissions
• FCC • IC
• CE • C-Tick
Dimensions
• 144 (W) x 109 (D) x 30 (H) mm (5.67 x 4.29 x 1.18 inches)
Maximum wireless signal rate derived from IEEE Standard 802.11g and 802.11n specifications. Actual data throughput will vary. Network conditions and environmental factors,
including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Environmental conditions will adversely
affect wireless signal range.
2
Range varies depending on country’s regulation.
1
D-Link DAP-1360 User Manual
98
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their
respective owners.
Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the
United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright ©2010-2011 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
D-Link DAP-1360 User Manual
99
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory
to match the intended destination. The firmware setting is not accessible by the end user.
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum gain of [2] dB. Antenna having a higher gain is strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50 ohms.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter (IC: 4216A-AP1360C1 / Model: DAP-1360C1) has been approved by Industry Canada to operate with the antenna types listed
below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this
list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet
aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,
y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
D-Link DAP-1360 User Manual
100
NOTE IMPORTANTE:
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit
être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal de dB [2]. Une antenne à gain plus élevé est strictement interdite
par les règlements d’Industrie Canada. L’impédance d’antenne requise est de 50 ohms.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peutfonctionner avec une antenne d’un type et d’un gain maximal
(ou inférieur) approuvé pourl’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l’intention des autres
utilisateurs, il faut choisir le type d’antenne et son gain de sorte que lapuissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité
nécessaire àl’établissement d’une communication satisfaisante.
Le présent émetteur radio (IC: 4216A-AP1360C1 / Model: DAP-1360C1) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne
énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
Antenna information: dipole / 2dBi (Brand:D-Link / Manufacturer :WHA YU)
D-Link DAP-1360 User Manual
101