CP-255ID
CV, SV, VGA and DVI to DVI Scaler / Converter
OPERATION MANUAL
DISCLAIMERS
The information in this manual has been carefully checked and is
believed to be accurate. CYP (UK) Ltd assumes no responsibility for any
infringements of patents or other rights of third parties which may result
from its use.
CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be
contained in this document. CYP (UK) Ltd also makes no commitment to
update or to keep current the information contained in this document.
CYP (UK) Ltd reserves the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted, transcribed,
stored in a retrieval system, or any of its part translated into any language
or computer file, in any form or by any means—electronic, mechanical,
magnetic, optical, chemical, manual, or otherwise—without express
written permission and consent from CYP (UK) Ltd.
© Copyright 2011 by CYP (UK) Ltd.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate
this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts inside
the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if
it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE
SUMMARY OF CHANGE
v1.00
First release
17/04/2013
CONTENTS
1. Introduction�������������������������������������������6
2. Applications�������������������������������������������6
3. Package Contents����������������������������������6
4. System Requirements���������������������������6
5. Features��������������������������������������������������7
6. Operation Controls and Functions�������8
6.1 Front Panel��������������������������������������������������� 8
6.2 Rear Panel����������������������������������������������������� 9
6.3 Remote Control����������������������������������������10
6.4 RS-232 Protocols��������������������������������������11
6.5 RS-232 Commands����������������������������������12
6.6 OSD MENU�������������������������������������������������14
7. Connection Diagram�������������������������� 18
8. Specifications�������������������������������������� 19
8.1 Technical Specifications������������������������19
8.2 Resolution Support���������������������������������20
9. Acronyms��������������������������������������������� 22
1. INTRODUCTION
T​ he CP-255ID is a Digital Video Scaler designed to accept Composite
Video, S-Video, PC, and DVI input signals. These inputs can be switched
and scaled and are outputted via DVI port.
External audio input signals can be switched and sent to the L/R output
port correspondingly with the video source selection. The control can be
done through on-panel buttons, IR remote, or RS-232, and there is OSD
(On Screen Menu) providing selection and system information. The device
provides full range of output resolutions, up to 1080p for HDTV timing,
and WUXGA (RB) for PC timing. The control can be done through onpanel buttons, IR remote, or RS-232, and there is OSD (On Screen Menu)
providing selection and system information.
2. APPLICATIONS
Analogue to Digital video signal conversion
Analogue and Digital Source Integration
Upscaling Standard definition video for High-Definition displays
3. PACKAGE CONTENTS
Digital Video Scaler
Remote Control (CR-118)
Power Adaptor
Operation Manual
4. SYSTEM REQUIREMENTS
Source equipment such as PC/Laptop or DVD Player with HDMI to DVI
adaptor, analogue sources via standard cabling and DVI display with
active speakers and connection cables.
6
5. FEATURES
Supports the conversion of multiple video and audio formats to DVI
Supports synchronized output for input video and output audio
signals
Supports 3D de-interlacing, noise reduction and Comb filter
Supports frame rate conversion
Supports control via RS-232, IR Remote handset and front panel
controls
7
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
DIGITAL VIDEO SCALER CP-255ID
POWER
XGA
CV
SV
PC
DVI
MENU
-
+
ENTER
720P
1
2
3
4
5
1 POWER & LED: Press this button to switch the device ON or to put
the device into standby mode. When the device is connected to an
active power supply the LED will illuminate and the device will switch
ON automatically.
2 IR (IR window): Receives only the IR signal from the supplied remote
control.
3 INPUT button and LEDs (CV/SV/PC/DVI):
Press to directly select the required input. An LED will illuminate to
indicate the currently selected source.
4 MENU: Press this button to enter into the on-screen menu (OSD).
5 −/+ (Minus/Plus): Use these buttons to navigate down and up in the
on-screen menu.
6 ENTER: Press this button to confirm the selection.
Note:
Pressing '−' (MINUS) and ENTER simultaneously will immediately switch
the output resolution of the device to 720p60.
Pressing '+' (PLUS) and ENTER simultaneously will immediately switch the
output resolution of the device to XGA.
8
6.2 Rear Panel
1
2
4
IN
SERVICE
RS232
DVI OUT
3
L/R OUT
DVI
L/R
PC
L
SV
R
DC 5V
CV
5
6
1 SERVICE: Reserved for manufacturer use only.
2 RS-232: Connect to a PC or RS-232 control system to control the
device with RS232 commands (see Sectionsm 6.5 and 6.6 for details).
3 DVI OUTPUT:
Connect to a DVI display (TV/monitor) for PC signal output or to an
HDMI display with an HDMI to DVI adaptor.
4 L/R OUT (3.5 mm mini-jack output): Connect to an amplifier or
active speaker for audio output in analogue stereo.
5 IN (Inputs):
DVI: Connect to DVI source such as PC or Laptop or to a HDMI source
with a HDMI to DVI adaptor.
L/R: Connect to a source device's analogue (L/R) output with a 3.5 mm
mini-jack cable.
PC: Connect to a PC or Laptop with a D-Sub 15pin cable.
CV + L/R: Connect to a source device such as video/DVD player for
both video and audio.
SV + L/R: Connect to a source device such as video/DVD player for
both S-Video and audio.
6 DC 5V: Connect the 5 V DC power supply to the device and plug the
adaptor into an AC wall outlet.
9
6.3 Remote Control
1 POWER:
Press this button to switch the
device ON or to put the device into
standby mode
POWER
2 CV/SV/PC/DVI:
CV
Press to directly select the required
input.
SV
Press this button to exit the menu
or the current selection in the onscreen menu.
DVI
3
EXIT
4 MENU:
Press this button to enter the onscreen menu.
2
PC
3 EXIT:
MENU
5
AUTO
ADJUST
Press the button to optimize the
positioning of the picture (picture
centering) on the screen.
CR-118
7 OK & :
Press OK to confirm the selection or use the directional buttons to
navigate the on-screen menus.
10
6
7
Press this button to return the
device to the factory default
settings.
6 AUTO ADJUST:
4
OK
RESET
5 RESET:
1
6.4 RS-232 Protocols
CP-255ID
Remote Control
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
2
Rx
3
Rx
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
►
◄
Baud Rate: 9600bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
11
6.5 RS-232 Commands
Command
Description
Contents
S SOURCE 1~4
Select input source
1=DVI
2=VIDEO
3=S-VIDEO
4=PC
R SOURCE
Inquire input source
Reports the numerical equivilent for
SOURCE setting (as above)
S OUTPUT 0~25
Select output timing
0=Native
1=640×480
2=800×6003=1024×768
4=1280×768
5=1360×768
6=1280×720
7=1280×800
8=1280×1024
9=1440×900
10=1400×1050
11=1680×1050
12=1600×1200
13=1920×1080
16=1920×1200
17=480p
18=720p 60
19=1080p 60
20=1080i 60
22=576p
23=720p 50
24=1080p 50
25=1080i 50(25)
R OUTPUT
Inquire output timing
Reports the numerical equivilent for
OUTPUT setting (as above)
S SIZE 0~6
Select output size
0=OVERSCAN
1=FULL
2=BEST FIT
3=PAN SCAN
4=LETTER BOX
5=UNDER 2
6=UNDER 1
R SIZE
Inquire output size
Reports the numerical equivilent for SIZE
setting (as above)
S PCAUTO I
PC Mode / Auto Setup
S CONTRAST 0~60
Contrast Setting
R CONTRAST
Inquire contrast setting
S BRIGHTNESS 0~60
Brightness setting
R BRIGHTNESS
Inquire brightness setting
S HUE 0~60
Hue setting
12
Command
Description
Contents
R HUE
Inquire hue setting
S SATURATION 0~60
Saturation setting
R SATURATION
Inquire saturation setting
S SHARPNESS 0~30
Sharpness setting
R SHARPNESS
Inquire sharpness setting
S NR 0~3
Noise reduction setting
0=OFF / 1=LOW / 2=MIDDLE / 3=HIGH
R NR
Inquire noise reduction
Reports the numerical equivilent for the
setting
NR setting (as above)
S AUDIODELAY 0~3
Audio delay setting
0=OFF / 1=40ms / 2=110ms(2) / 3=50ms
R AUDIODELAY
Inquire audio delay setting
Reports the numeric equivilent for
S AUDIOMUTE 0/1
Audio mute setting
R AUDIOMUTE
Inquire audio mute setting
S KEY LOCK 0/1
Key lock setting
0=ENABLE / 1=DISABLE
R KEY LOCK
Inquire key lock setting
Reports the numeric equivilent for KEY
AUDIODELAY setting (as above)
0=ON / 1=MUTE
LOCK setting (as above)
FW
Firmware checking
S RESET 1
Pre-reset
S POWER 0/1
Power On/Off
0=OFF / 1=ON
R POWER
Power Status
Reports the numeric equivilent for
POWER setting (as above)
Note: RS-232 commands will be not executed unless followed with a carriage
return and LF. Commands are case-insensitive.
13
6.6 OSD MENU
1st Layer
2nd layer
3rd Layer
DISPLAY
OUTPUT
Native
640×480 60
800×600 60
1024×768 60
1360×768 60
1280×720 60
1280×800 60
1280×1024 60
1440×900 60
1400×1050 60
1680×1050 60
1600×1200 60
1920×1080 60
1920×1200 60
720×480P 60
1280×720P 60
1920×1080I 60
1920×1080P 60
720×576P 50
1280×720P 50
1920×1080I 50
1920×1080P 50
14
4th Layer
1st Layer
2nd layer
3rd Layer
SIZE (VIDEO mode
only)
OVER SCAN
4th Layer
FULL
BEST FIT
PAN SCAN
LETTER BOX
UNDER 2
UNDER 1
MODE INFO
INFO
ON
OFF
PC(PC mode only)
AUTO SETUP
No
YES
H_POSITION
0~60 (30)
V_POSITION
0~60 (30)
PHASE
CLOCK
WXGA/XGA
XGA
WXGA
RESET
NO
YES
15
1st Layer
2nd layer
3rd Layer
4th Layer
COLOUR
COLOUR
R
0~1023 (512)
G
0~1023 (512)
B
0~1023 (512)
R OFFSET
0~1023 (512)
G OFFSET
0~1023 (512)
B OFFSET
0~1023 (512)
CONTRAST
0~60 (30)
BRIGHTNESS
0~60 (30)
HUE (VIDEO mode
only)
0~60 (30)
SATURATION (VIDEO
mode only)
0~60 (30)
SHARPNESS (VIDEO
mode only)
0~30 (0)
NR. (VIDEO mode
only)
OFF
LOW
MIDDLE
HIGH
AUDIO
VOLUME
0~100
DELAY (L/R output
only)
OFF
40 ms
110 ms
150 ms
SOUND
ON
MUTE
16
1st Layer
2nd layer
3rd Layer
SETUP
FACTORY RESET
NO
4th Layer
YES
KEY LOCK
OFF
ON
POWER SAVE
OFF
ON
INFORMATION
INPUT
OUTPUT
REVISION
Note:
Items in Bold are the Factory default settings.
Items in brackets are the default values for those settings
17
7. CONNECTION DIAGRAM
DVD Player
RS-232 Equipped
PC or Laptop
Analogue
Stereo
Input
RS-232
Composite
Video Input
Analogue Stereo Output
S-Video
Input
IN
SERVICE
RS232
DVI OUT
L/R OUT
DVI
L/R
PC
L
SV
R
DC 5V
CV
AV Receiver
Power
Supply
DVI
Output
VGA &
Analogue
Stereo
Input
DVI Input
TV or Monitor
PC or
Laptop
18
PC or
Laptop
8. SPECIFICATIONS
8.1 Technical Specifications
Video Bandwidth
165 MHz
Input Ports
1×Composite, 1×S-Video, ,1×VGA,
1×DVI, 1×L/R, 1×LR, 1×USB (service only),
1×RS-232 (Control Only)
Output Port
1×DVI, 1×L/R
Input Resolution Support
Up to WUXGA & 1080p
Output Resolution Support
Up to WUXGA & 1080p
Power Supply
5V/2.6A DC (US/EU standards, CE/FCC/
UL certified)
Dimensions
215 mm (W)×165 mm(D)×47 mm (H)
Weight
970 g
Chassis Material
Metal
Colour
Black
Operating Temperature
0 ˚C ~ 40 ˚C / 32 ˚F ~ 104 ˚F
Storage Temperature
−20 ˚C ~ 60 ˚C / −4 ˚F ~ 140 ˚F
Relative Humidity
20 ~ 90% RH (non-condensing)
Power Consumption
5.7 W
19
8.2 Resolution Support
Input Resolution
PC
DVI/HDMI
CV/SV
NTSC

PAL

VGA640×480 (@60/72/75 Hz)


SVGA800×600 (@56/60/72/75 Hz)


XGA1024×768 (@60/70/75 Hz)


XGA+1152×864 @75 Hz


1280×720 @60 Hz


1280×768 @60 Hz


1280×800 @60 Hz


1280×960 @60 Hz


1280×1024 (@60/75 Hz)


1360×768 @60 Hz


SXGA+1400×1050 @60 Hz


WXGA+1440×900 @60 Hz


UXGA1600×1200 @60 Hz


WSXGA1680×1050 RB @60 Hz


1920×1080@60 Hz


1920×1200 RB@60 Hz


480i/576I

480p/576p

720p(@50/60 Hz)

1080i(@50/60 Hz)

1080p(@24/30/50/60 Hz)

20
DVI/HDMI output Resolution
Native
640×480@60 Hz
800×600@60 Hz
1024×768@60 Hz
1360×768@60 Hz
1280×720@60 Hz
1280×800@60 Hz
1280×1024@60 Hz
1440×900@60 Hz
1400×1050@60 Hz
1680×1050@60 Hz
1600×1200@60 Hz
1920×1080@60 Hz
1920×1200@60 Hz
480p
576p
720p (@50/60 Hz)
1080i (@50/60 Hz)
1080p (@50/60 Hz)
21
9. ACRONYMS
ACRONYM
COMPLETE TERM
COMP
Component Video
CV
Composite Video
DVI
Digital Visual Interface
RGB
Red Green Blue
SV
S-Video
VGA
Video Graphics Array
UXGA
Ultra Extended Graphics Array
WUXGA
Widescreen Ultra Extended Graphics Array
22
CYP (UK) Ltd., Unit 7, Shepperton Business Park, Govett Avenue, Shepperton,
Middlesex, TW17 8BA
Tel: +44 (0) 20 3137 9180 | Fax: +44 (0) 20 3137 6279
Email: sales@cypeurope.com
www.cypeurope.com
v1.00