Model VC4400 User Guide
5 Disc DVD Changer
Downloaded From Disc-Player.com Marantz Manuals
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the product and
receiver.
Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
NOTES ON COPYRIGHTS:
CAUTION:
This Digital Video Disc Player employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference should the unit
require maintenance, contact an authorized service location
(see service procedure).
Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product features the copy protection function developed
by Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ___________________________________
Serial No. ___________________________________
2
Downloaded From Disc-Player.com Marantz Manuals
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.
AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this product near water. – For example:
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement; or near a swimming pool; and
other areas located near water.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over-heating. The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been
adhered to.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution
when moving the cart/product combination to
avoid injury from tip-over.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
3
Downloaded From Disc-Player.com Marantz Manuals
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Table of Contents
Introduction
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel and Display Window . . . . . . . . . . . . . . 7
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparation
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Connecting to a TV . . . . . . . . . . . . . . . . . . . . . . 10
Connecting to Optional Equipment . . . . . . . . . . . 11
Before Operation . . . . . . . . . . . . . . . . . . . . . . . 12-15
General Explanation. . . . . . . . . . . . . . . . . . . . . . 12
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 12
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 13-15
Initial Settings General Operation. . . . . . . . . 13
Language . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Picture. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Parental Control. . . . . . . . . . . . . . . . . . . . . . 15
Operation
Operation with DVD and Video CD . . . . . . . . . 16-19
Playing a DVD and Video CD. . . . . . . . . . . . . . . 16
Exchanging discs during playback . . . . . . . . 16
Skipping discs . . . . . . . . . . . . . . . . . . . . . . . 16
Exchanging the disc and starting playback . . 16
General Features . . . . . . . . . . . . . . . . . . . . . . . . 17
Moving to another TITLE . . . . . . . . . . . . . . 17
Moving to another CHAPTER/TRACK . . . . . 17
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Still Picture and Frame-by-Frame Playback . 17
Slow Motion. . . . . . . . . . . . . . . . . . . . . . . . . 17
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 18
Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Time Search . . . . . . . . . . . . . . . . . . . . . . . . 18
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 18
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Marker Search . . . . . . . . . . . . . . . . . . . . . . . 19
Special DVD Features . . . . . . . . . . . . . . . . . . . . 19
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 19
Changing the Audio Language . . . . . . . . . . . 19
Changing the Audio Channel . . . . . . . . . . . . 19
Subtitles . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4
Downloaded From Disc-Player.com Marantz Manuals
Operation with Audio CD and MP3/WMA Disc . . 20-21
Playing an Audio CD and MP3/WMA Disc . . . . . 20
Notes on MP3/WMA Recordings . . . . . . . . . . . . 20
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Moving to another Track . . . . . . . . . . . . . . . 21
Repeat Track/ All/ Off. . . . . . . . . . . . . . . . . . 21
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 21
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 21
Changing the Audio Channel . . . . . . . . . . . . 21
Repeat Track/Disc/All/Off . . . . . . . . . . . . . . . 21
Operation with JPEG Disc. . . . . . . . . . . . . . . . . . . 22
Viewing a JPEG disc . . . . . . . . . . . . . . . . . . . . . 22
Moving to another File . . . . . . . . . . . . . . . . . 22
Still Picture . . . . . . . . . . . . . . . . . . . . . . . . . 22
To flip the picture . . . . . . . . . . . . . . . . . . . . . 22
To rotate picture. . . . . . . . . . . . . . . . . . . . . . 22
Notes on JPEG Recordings . . . . . . . . . . . . . 22
Programmed Playback . . . . . . . . . . . . . . . . . . . 23-24
Programmed Playback with Audio CD . . . . . . . . 23
Programmed Playback with MP3/WMA disc . . . . 23
Programmed Playback with Video CD . . . . . . . . 23
Repeat Programmed Tracks . . . . . . . . . . . . 24
Erasing a Track from Program List . . . . . . . . 24
Erasing the Complete Program List . . . . . . . 24
Additional Information . . . . . . . . . . . . . . . . . . . . . 25
Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Video Mode Setting . . . . . . . . . . . . . . . . . . . . . . 25
Setting Remote control codes of DVD player . . . 25
Reference
Troubleshooting . . .
Language Code List
Country Code List . .
Specifications . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
26
27
28
29
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
Before Use
Title (DVD only)
The main film content or accompanying feature content
or additional feature content, or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
DVD
(8 cm / 12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit can play a DVD-R, DVD±RW,
Kodak PICTURE CD, SVCD, and CD-R or CD-RW that
contains audio titles, MP3, WMA or JPEG files.
Notes
– Depending on the conditions of the recording equipment or the CD-R/RW (or DVD-R/±RW) disc itself,
some CD-R/RW (or DVD-R/±RW) discs cannot be
played on the unit.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
Notes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs
may be intentionally fixed by software manufacturers.
As this unit plays DVDs and Video CDs according to
disc content designed by the software manufacturer,
some playback features of the unit may not be available
or other functions may be added.
Refer also to the instructions supplied with the DVDs
and Video CDs. Some DVDs made for business purposes may not be played on the unit.
Regional code of the DVD player and DVDs
This DVD player is designed and manufactured
for playback of region “1” encoded DVD software. The region code on the labels of some
DVD discs indicates which type of player can play those
discs. This unit can play only DVD discs labeled “1” or
“ALL”. If you try to play any other discs, the message
“Check Regional Code” will appear on the TV screen.
Some DVD discs may not have a region code label even
though their playback is prohibited by area limits.
1
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number,
enabling you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Track (Video CD and audio CD only)
Sections of a picture or a musical piece on a video CD
or an audio CD. Each track is assigned a track number,
enabling you to locate the track you want.
Scene
On a video CD with PBC (Playback control) functions,
moving pictures and still pictures are divided into sections called “Scenes”. Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want.
A scene is composed of one or several tracks.
Types of video CDs
There are two types of video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact
with the system via menus, search functions, or other
typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included in
the disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs
allow playback of video pictures as well as sound, but
they are not equipped with PBC.
5
Downloaded From Disc-Player.com Marantz Manuals
INTRODUCTION
Disc-related terms
Playable Discs
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packed at the factory.
Notes on Discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
To keep the exterior surfaces clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Storing discs
Cleaning the unit
Cleaning discs
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center out.
To obtain a clear picture
The DVD player is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Remote Control Operation Range
Point the remote control at the remote sensor and
press the buttons.
Distance: About 16 ft (5 m) from the front of the
remote sensor.
Angle: About 30° in each direction of the front of the
remote sensor.
AAA
AAA
Remote control battery installation
Detach the battery cover on the rear of
the remote control, and insert two R03
(size AAA) batteries with
and
aligned correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
6
Downloaded From Disc-Player.com Marantz Manuals
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature
increase inside the car.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
About Symbols
About the
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbol is
applicable only to the disc represented by the symbol.
DVD DVD
VCD2.0 Video CDs with the PBC (playback control)
function.
VCD1.1 Video CDs without the PBC (playback control)
function.
CD
Audio CDs.
MP3 MP3 discs.
WMA WMA discs.
JPEG JPEG discs.
Front Panel and Display Window
Disc Tray
Insert a disc here.
DISC SKIP
Moves to the next
available disc tray.
POWER
Display window
Shows the current
status of the player.
OPEN/CLOSE ( / )
Opens or closes the
disc tray.
INTRODUCTION
STANDBY
Lights red when the
DVD player is standby.
Remote Sensor
ON/STANDBY
Reverse Skip/Scan ( S / Q )
Go to beginning of current
chapter/track or to PREVIOUS
chapter/track.
Press and hold for two seconds for a
fast reverse search.
Switches the
player ON and
STANDBY.
Forward Skip/Scan ( R / T )
Go to NEXT chapter/track.
Press and hold for two seconds for
a fast forward search.
DISC EX-CHANGE
Changes a disc (other than the
one playing) during playback
PLAY ( 2 )
Starts playback.
STOP ( 9 )
Stops playback.
PAUSE ( ; )
Pause playback temporarily/ press repeatedly
for frame-by-frame playback.
ANGLE Lights when multi angles are
present.
A light will appear if a disc is in the
disc tray. The current disc tray flashes.
DVD
TITLE Indicates current title number
DVD inserted
CHP/TRK Indicates current chapter or track number
CD Audio CD inserted
Indicates total playing time/elapsed time
VCD Video CD inserted
MP3 MP3 or WMA disc inserted
PROG. Programmed playback active
RANDOM RANDOM
playback active
Indicates current player function:
Playback, Pause, etc.
Indicates repeat
mode
MP3 VCD
CD DVD
1
2
3
TITLE
CHP/TRK
PROG.
RANDOM ALL A
B
5
4
7
Downloaded From Disc-Player.com Marantz Manuals
Remote Control
MARKER •
Marks any point during playback.
OPEN/CLOSE
Opens and closes the disc tray.
SEARCH •
Displays MARKER SEARCH menu.
ANGLE
Selects a DVD camera angle if
available
POWER
Switches DVD Player ON and OFF.
AUDIO
Selects an audio language (DVD) or
an audio channel (CD).
SUBTITLE
Selects a subtitle language.
0-9 number buttons
Selects numbered items in a menu.
Reverse SKIP/SCAN ( S ) •
Search backward*/ go to beginning
of current chapter or track or go to
previous chapter or track.
* Press and hold button for about
two seconds.
PLAY ( 2) •
Starts playback.
Forward SKIP/SCAN ( T ) •
Search forward*/ go to next chapter or track.
OSD
Accesses On-Screen display.
MENU
Accesses menu on a DVD disc.
TOP MENU •
Displays the discs Top menu, if
available.
SETUP •
Accesses or removes setup menu.
RANDOM
Plays tracks in random order.
PROGRAM
Enters to the program edit mode or
exits from that.
CLEAR
Removes a track number on the
program list or a mark on the
MARKER SEARCH menu.
• ZOOM
Enlarges video image.
• STOP ( 9 )
Stops playback.
• PAUSE/STEP ( ; )
Pauses playback temporarily/ press
repeatedly for frame-by-frame
playback.
SELECT/ENTER
Acknowledges menu selection.
SLOW ( , / . )
Reverse/ Forward slow playback.
1/2
2/3
3/4
4 (left/right/up/down)
- Selects an item in the menu.
• REPEAT
Repeat chapter, track, title all.
• A-B
Repeat sequence.
• DISC SKIP
Moves to the next available disc tray.
RETURN •
- Removes the setup menu.
- Displays the menu of a video
CD with PBC.
Setting Remote control codes of Remote control
• This remote control supports two remote control codes: C004 and C044.
• When the unit is shipped from the factory, the remote control is set to C004.
• To set the remote control to C044, hold down both the STOP button and "2" number button on the remote control
for at least five seconds.
• You can change the code of remote control only when NO DISC appears in the display window.
• To set the remote control back to C004, hold down both the STOP button and "1" number button on the
remote control for at least five seconds.
• Also set the remote control codes of the player to the same setting as the remote control.
(This setting is set to C004, when the unit is shipped from the factory.) (page 25)
8
Downloaded From Disc-Player.com Marantz Manuals
Rear Panel
OPTICAL (Digital audio out jack)
Connect to digital (optical) audio equipment.
INTRODUCTION
COAXIAL (Digital audio out jack)
Connect to digital (coaxial) audio equipment.
COMPONENT VIDEO OUT (Y, CB/PB, CR/PR)
Connect to a TV with Y, CB/PB, CR/PR inputs.
AUDIO OUT1 (Left/Right)
Connect to an amplifier, receiver,
or stereo system.
VIDEO OUT
Connect to a TV with video inputs.
AUDIO OUT2 (Left/Right)
Connect to an amplifier, receiver,
or stereo system.
S-VIDEO OUT
Connect to a TV with S-Video inputs.
AC Power Cord
Plug into the power source.
Caution
Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent
damage to the unit.
9
Downloaded From Disc-Player.com Marantz Manuals
Connections
Tips
Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the player. Use only one of the connections
described below.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the
best connections.
For better sound reproduction, connect the player’s
AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment.
See “Connecting to Optional Equipment”
on page 11.
Caution
– Make sure the DVD Player is connected directly to the
TV. Tune the TV to the correct video input channel.
– Do not connect the DVD Player’s AUDIO OUT jack to
the phono in jack (record deck) of your audio system.
– Do not connect your DVD Player via your VCR. The
DVD image could be distorted by the copy protection
system.
Connecting to a TV
Make one of the following connections, depending on
the capabilities of your existing equipment.
Progressive Scan (Color Stream® pro) connection
1
If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD
Player’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the DVD Player.
Connect the COMPONENT VIDEO OUT jacks on
the DVD Player to the corresponding in jacks on
the TV using an optional Y, CB/PB, CR/PR cable (C).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD Player to the audio left/right in jacks on the
TV (A) using the supplied audio cables.
Notes
– Set the Progressive to “On” on the setup menu for
progressive signal, see page 13.
– Progressive scan does not work with the analog video
connections (yellow VIDEO OUT and S-VIDEO OUT
jack). (See “Video mode setting”, page 25)
Rear of TV
Video connection
S-VIDEO
INPUT
the VIDEO OUT jack on the DVD Player to
1 Connect
the video in jack on the TV using the video cable (V).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD Player to the audio left/right in jacks on the
TV (A) using the audio cables.
COMPONENT VIDEO /
PROGRESSIVE SCAN INPUT
Pr
Pb
VIDEO
INPUT
AUDIO INPUT
Y
L
R
L
S-Video connection
1
Connect the S-VIDEO OUT jack on the DVD Player
to the S-Video in jack on the TV using the S-Video
cable (S).
S
C
A
V
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD Player to the audio left/right in jacks on the
TV (A) using the audio cables.
Component Video (Color Stream®) connection
1
Connect the COMPONENT VIDEO OUT jacks on
the DVD Player to the corresponding in jacks on
the TV using an Y, CB/PB, CR/PR cable (C).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD Player to the audio left/right in jacks on the
TV (A) using the audio cables.
Notes
– Refer to the owner’s manual of your TV as well.
– Before you connect the DVD player to your TV, be
sure to turn off the power and unplug both units from
the wall outlet before making any connections.
10
Downloaded From Disc-Player.com Marantz Manuals
Rear of DVD player
Caution
– Do not set the Digital Audio Output of this DVD player to
“Dolby Digital” unless you are connecting the DIGITAL
OUT jack of this DVD player to an AV decoder that has
the Dolby Digital decoding function. High volume sound
may damage your hearing as well as the speakers.
Connections (Continued)
Connecting to Optional Equipment
Rear of DVD player
PREPARATION
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Pro Logic ll/
Pro Logic
Connect the Left and Right AUDIO OUT jacks on the
DVD Player to the audio left and right in jacks on your
amplifier, receiver, or stereo system, using the audio
cables (A).
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/
Video receiver equipped with a multi-channel
decoder (Dolby Digital™, MPEG 2, or DTS)
1
Connect one of the DVD Player’s DIGITAL AUDIO
OUT jacks (OPTICAL O or COAXIAL X) to the corresponding in jack on your amplifier. Use an optional digital (optical O or coaxial X) audio cable.
2
You will need to activate the player’s digital output.
(See “Digital Audio Output” on page 14).
O
X
OPTICAL
COAXIAL
DIGITAL INPUT
A
L
R
AUDIO INPUT
Amplifier (Receiver)
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD Player (MPEG 2,
Dolby Digital and DTS). Check the receiver manual and
the logos on the front of the receiver.
Caution:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
Notes
– If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
– To see the audio format of the current DVD in the onscreen display, press AUDIO.
Notes
– Refer to the owner’s manual of your audio system as
well.
– Before you connect the DVD player to other equipment, be sure to turn off the power and unplug all of
the equipment from the wall outlet before making any
connections.
– If you place the DVD player near a tuner or radio, the
radio broadcast sound might be distorted. In this
case, move the DVD player away from the tuner and
radio.
– The output sound of the DVD player has a wide
dynamic range. Be sure to adjust the receiver’s volume to a moderate listening level. Otherwise, the
speakers may be damaged by a sudden high volume
sound.
– Turn off the receiver before you connect or disconnect
the DVD player’s power cord. If you leave the receiver power on, the speakers may be damaged.
11
Downloaded From Disc-Player.com Marantz Manuals
Before Operation
Temporary Feedback Field Icons
General Explanation
This manual gives basic instructions for operating the
DVD Player. Some DVDs require specific operation or
allow only limited operation during playback. When this
occurs, the symbol
appears on the TV screen, indicating that the operation is not permitted by the DVD
Player or is not available on the disc.
TITLE
On-Screen Display
Repeat Chapter
TRACK
Repeat Track (non-PBC Video CDs only)
ALL
Repeat All Tracks (non-PBC Video CDs only)
A B
Repeat A-B
OFF
Repeat Off
Resume play from this point
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
1 Press OSD during playback.
4 to select an item.
Press 3/4
2 The
selected item will be highlighted.
2 to change the setting of an item.
Press 1/2
3 The
number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
Repeat Title
CHAPT
Action prohibited or not available
Notes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
press SELECT/ENTER to execute the setting.
DVD
Items
4 to select desired item)
Function (Press 3/4
Selection Method
1 /3
Shows the current title number and total number of
titles, and skips to the desired title number.
1 / 2, or
Numbers, SELECT/ENTER
1 /12
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
1 / 2, or
Numbers, SELECT/ENTER
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
Numbers, SELECT/ENTER
Title Number
Chapter Number
Time search
0:20:09
Audio language
and Digital Audio
Output mode
Subtitle language
1 ENG
D
5.1 CH
OFF
ABC
Angle
Sound
VCD2.0
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
1 / 2, or
AUDIO
1 / 2, or
SUBTITLE
1 /1
Shows the current angle number and total number of
angles, and changes the angle number.
1 / 2, or
ANGLE
NORM.
Shows the current sound mode (NORMAL or 3D SURROUND), and changes the setting.
1 /2
VCD1.1
Items
Track Number
1 /4
Time
0:20:09
Audio Channel
STER.
Sound
12
Downloaded From Disc-Player.com Marantz Manuals
NORM.
4 to select desired item)
Function (Press 3/4
Selection Method
Shows the current track number, total number of tracks
and PBC On mode, and skip to the desired track number.
1 / 2, or
Numbers, SELECT/ENTER
Shows the elapsed playing time (Display only)
Shows the audio channel, and
changes the audio channel.
Shows the current sound mode (NORMAL or 3D SURROUND), and changes the setting.
–
1 / 2, or
AUDIO
1 /2
Before Operation (Continued)
Picture
You can set your own Personal Preferences on the
player.
TV Aspect
Initial Settings General Operation
1
Press SETUP.
The setup menu appears.
DVD
4:3 Letterbox: Select when a standard 4:3 TV is connected. Displays theatrical images with masking bars
above and below the picture.
4:3 Panscan: Select when a conventional TV set is
connected. The video material formatted in the Pan &
Scan style is played back in that style (Both sides of the
picture are cut off).
16:9 Wide: Select when a 16:9 wide TV is connected.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Disc Audio
4:3 Letterbox
Country Code
Spanish
Disc Subtitle
4:3 Panscan
TV Aspect
Italian
Disc Menu
16:9 Wide
Menu Language
Chinese
Rating
Progressive Scan
Polish
Country Code
Digital Audio Output
Hungarian
Other – – – –
Others
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
3/4
4 to select the desired item.
2 Press
The screen will show the current setting for the
selected item, as well as alternate setting(s).
While the desired item is selected, press 2, then
3/4
4 to select the desired setting.
Press SELECT/ENTER to confirm your selection.
Some items require additional steps.
3
4
SETUP, RETURN, or PLAY to exit the
5 Press
setup menu.
Language
Disc Language
Others
Progressive Scan
DVD
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the COMPONENT VIDEO OUT jacks,
but are connecting the DVD Player to a standard (analog) television, set Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
DVD
Select a language for the disc’s Menu, Audio, and
Subtitle.
Original : The original language set for the disc is selected.
Other : To select another language, press number buttons to
enter the corresponding 4-digit number according to the language code list on page 27. If you enter the wrong language
code, press CLEAR.
Disc Audio
Original
Disc Subtitle
English
Disc Menu
French
Rating
German
Country Code
Spanish
TV Aspect
Italian
Menu Language
Chinese
Progressive Scan
Polish
Digital Audio Output
Hungarian
Other – – – –
Others
Menu Language
Select a language for the setup menu. This is the menu
you see when you press SETUP.
Disc Audio
English
Disc Subtitle
Spanish
Disc Menu
French
Disc Audio
4:3 Letterbox
Disc Subtitle
4:3 Panscan
Disc Menu
16:9 Wide
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
Others
Caution
Once the setting for progressive scan output is entered, an
image will only be visible on a progressive scan compatible
TV or monitor. If you set Progressive Scan to On in error, you
must reset the unit. Press STOP to stop any disc that is playing. Next, press STOP again and hold it for five seconds
before releasing it. The video output will be restored to the
standard setting, and a picture will once again be visible on a
conventional analog TV or monitor.
Rating
Country Code
TV Aspect
Menu Language
13
Downloaded From Disc-Player.com Marantz Manuals
PREPARATION
Initial Settings
Before Operation (Continued)
Sound
Others
Digital Audio Output
The DRC, Vocal, PBC and Auto Play settings can
be changed.
4 to select the desired item and press
Press 3/4
SELECT/ENTER. The setting of the selected item is
changed between On and Off.
Each DVD disc has a variety of audio output options.
Set the player’s Digital Audio Output according to the
type of audio system you use.
DOLBY DIGITAL/PCM: Select “DOLBY DIGITAL/PCM”
if you connected the DVD Player’s DIGITAL OUT jack to
a Dolby Digital decoder (or an amplifier or other equipment with a Dolby Digital decoder).
Stream/PCM: Select “Stream/PCM” if you connected
the DVD Player’s DIGITAL OUT jack to an amplifier or
other equipment with a DTS decoder, Dolby Digital
decoder or MPEG decoder.
PCM: Select when connected to a 2-channel digital
stereo amplifier. The DVD player outputs sounds in the
PCM 2ch format when you play a DVD video disc
recorded on the Dolby Digital, MPEG1, or MPEG2
recording system.
Disc Audio
DOLBY
DIGITAL
Disc Subtitle
Stream/PCM
Disc Menu
PCM
/PCM
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Sample Freq.
48 KHz
96KHz
Digital Audio Output
Others
Sample Frequency
To change the Sample Frequency setting, first select
the desired Digital Audio Output as indicated as above.
If your receiver or amplifier is NOT capable of handling
96KHz signals, select 48KHz. When this choice is
made, this unit will automatically convert any 96KHz
signals to 48KHz so your system can decode them.
If your receiver or amplifier is capable of handling
96KHz signals, select 96KHz. When this choice is
made, this unit will pass each type of signal through
without any further processing.
Disc Audio
DRC
On
Disc Subtitle
Vocal
On
Disc Menu
PBC
On
Rating
Auto Play
Off
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
Others
Dynamic Range Control (DRC)
DVD
With the DVD format, you can hear a program’s soundtrack in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
Vocal
DVD
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
PBC
VCD2.0
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to the PBC.
Off: Video CDs with PBC are played the same way as Audio
CDs.
Auto Play
DVD
You can set up the DVD Player so a DVD disc automatically starts playing whenever the DVD is inserted.
If Auto Play mode is set to On, this DVD player will
search a title that playback time is long most and then
play back the title automatically.
On: Auto Play function is activated.
Off: Auto Play function is not activated.
Note
The Auto Play function may not work for some DVDs.
14
Downloaded From Disc-Player.com Marantz Manuals
Before Operation (Continued)
Parental Control
Country Code
Rating
Enter the code of a country/area whose standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 28.).
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are
country-dependent. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
Disc Audio
8
Disc Subtitle
7
Disc Menu
6
Rating
Country Code
5
TV Aspect
Menu Language
3
Progressive Scan
1
Digital Audio Output
Unlock
4
2
Change
Others
“Rating” on the Setup menu using the
1 Select
3/4
4 buttons.
2 While “Rating” is selected, press 2.
you have not entered a password yet.
3 When
Enter a 4-digit password using the numbered buttons to create a personal 4-digit security password.
then press SELECT/ENTER. Enter the 4-digit password again and press SELECT/ENTER to verify.
When you have already entered a password;
Enter a 4-digit password using the numbered buttons to confirm the personal 4-digit security password, then press SELECT/ENTER.
If you make a mistake before pressing SELECT/ENTER,
press CLEAR and enter 4-digit security password again.
4 butSelect a rating from 1 to 8 using the 3/4
4 tons.
One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the player, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
5
Press SELECT/ENTER to confirm your rating
selection, then press SETUP to exit the menu.
Disc Audio
Disc Subtitle
Code Set
U S
Disc Menu
Rating
Country Code
TV Aspect
Menu Language
Progressive Scan
Digital Audio Output
Others
4 buttons on
Select Country Code using the 3/4
1 the
setup menu.
2 While Country Code is selected, press 2.
3 Follow step 3 of “Rating” on left.
4 Select the first character using the 3/44 buttons.
the cursor using 2 button and select the
5 Shift
4 buttons.
second character using 3/4
SELECT/ENTER to confirm your country
6 Press
code selection, then press SETUP to exit the
menu.
Note
Confirmation of the 4-digit password is necessary when
the code is changed (see “Changing the 4-digit code”
below.).
Changing the 4-digit code
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old code, then press SELECT/ENTER.
4 buttons then press
3 Select Change using 3/4
SELECT/ENTER.
4 Enter the new 4-digit code, then press
SELECT/ENTER.
5 Enter exactly the same code a second time and verify by pressing SELECT/ENTER.
6 Press SETUP to exit the menu.
If you forget your 4-digit code
If you forget your password, to clear the current password, follow the procedure below.
1 Press SETUP to display the setup menu.
2 Use the Number buttons to enter the 6-digit number
“210499”.
The 4-digit password is cleared. “P CLr” appears on the
display for a moment.
3 Enter a new code as shown above to the left (Rating).
15
Downloaded From Disc-Player.com Marantz Manuals
PREPARATION
DVD
DVD
Operation with DVD and Video CD
Playing a DVD and Video CD
Playback Setup
DVD
VCD2.0
VCD1.1
Turn on the TV and select the video input source connected to the DVD player.
Audio system: Turn on the audio system and select
the input source connected to the DVD player.
1 Press OPEN/CLOSE to open the disc tray.
your chosen disc in the tray, with the
2 Load
playback side down.
Do not load a disc in the
left and light side position.
Center position
• Discs can be loaded one at a time by pressing
DISC SKIP to rotate the carousel.
OPEN/CLOSE to close the tray.
3 Press
READING appears on the TV screen, and playback
starts automatically. If playback does not start,
press PLAY.
In some cases, the disc menu might appear
instead.
Exchanging discs during playback
If a menu screen is displayed
VCD2.0
Use the number buttons to select the track you want
to view.
Press RETURN to return to the menu screen.
Menu setting and the exact operating procedures for
using the menu may differ depending on the disc.
Follow the instructions on the each menu screen.
You also may set PBC to Off under setup. See page
14.
1. Press OPEN/CLOSE during playback or when playback is stopped.
Play stops (if pressed during playback), the disc tray opens
and the disc that was in the play position comes to the front.
2. Exchange the disc.
3. Press OPEN/CLOSE or PLAY again.
The tray closes and playback begins (with the disc
that was in front).
After operation
When the unit is not in use, remove the disc and press
POWER to turn off the DVD player.
16
Downloaded From Disc-Player.com Marantz Manuals
Notes
When DISC SKIP is pressed, the disc tray rotates and
playback begins from the beginning of the next disc.
If there is no disc on the next disc tray, the following
disc tray will be selected.
When DISC SKIP is pressed during playback of disc
5, playback of disc 1 will start.
Exchanging the disc and starting playback
Caution
– Do not touch the loading drawer and carousel while
they are in motion, and do not attempt to rotate the
carousel by hand; doing so could result in incorrect
operation of the player and/or damage to the discs.
Note
The disc tray presently loaded in the play position can
not be exchanged.
Press DISC SKIP during play or when playback is
stopped.
DVD
2/3
3/4
4 buttons to select the title/chapter you
Use the 1/2
want to view, then press SELECT/ENTER to start playback.
Press TOP MENU or MENU to return to the menu
screen.
Press DISC EX-CHANGE on the front panel during
playback to open the disc tray.
Press DISC SKIP to rotate the disc trays to the
desired position. The carousel will rotate clockwise by
one disc increments.
Exchange the discs and press DISC EX-CHANGE or
OPEN/CLOSE to close the disc tray.
Skipping discs
The menu screen may be displayed first after loading a
DVD or Video CD which offer a menu.
Notes
If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit code must
be entered and/or the disc must be authorized (see
“Parental Control”, on page 15).
DVDs may have a region code.
Your player will not play discs that have a region code
different from your player. The region code for this
player is 1 (one).
Notes
Do not move the DVD player during playback. Doing
so may damage the disc and the DVD player.
Use the OPEN/CLOSE button on the remote control
or DVD player to open and close the disc tray. Do not
push the disc tray while it is moving. Doing so may
cause the DVD player to malfunction.
Do not push up the disc tray or put any objects other
than discs on the disc tray. Doing so may cause the
DVD video player to malfunction.
Keep your fingers well clear of the disc tray as it is
closing. Be especially careful with children’s fingers
around the closing disc tray as there is a risk of
personal injury.
Operation with DVD and Video CD
General Features
Still Picture and Frame-by-Frame playback
Note
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
1 Press PAUSE/STEP during playback.
The player will now go into PAUSE mode.
2 You can advance the picture frame-by-frame by
pressing PAUSE/STEP repeatedly on the remote control.
Moving to another TITLE
DVD
Moving to another CHAPTER/TRACK
VCD1.1
1 /12
Slow Motion
VCD2.0
VCD2.0
VCD1.1
1 Press SLOW t or T during playback.
The player will enter SLOW mode.
2 Use the SLOW t or T to select the required speed:
t 1/16, t 1/8, t 1/4 or t 1/2 (backward), or
T 1/16, T 1/8, T 1/4 or T 1/2 (forward).
3 To exit slow motion mode, press PLAY.
Notes
Slow motion playback in reverse is not applicable for
Video CD.
Random
VCD1.1
1 Press and hold SKIP/SCAN . or > for about
two seconds during playback.
The player will now go into SEARCH mode.
2 Press and hold SKIP/SCAN . or > repeatedly
to select the required speed: mX2, mX4, mX16,
mX100 (backward) or MX2, MX4, MX16,
MX100 (forward).
With a Video CD, the Search speed changes: mX2,
mX4, mX8, (backward) or MX2, MX4, MX8,
(forward).
3 To exit SEARCH mode, press PLAY.
Karaoke DVD
VCD2.0
VCD1.1
1 Press RANDOM during playback or in stop mode.
The unit automatically begins Random Playback and
“RANDOM(1-3)” appears on the display window.
• RANDOM1: Plays all the tracks on a single disc in random
order and then stops.
• RANDOM2: Plays all the tracks on current disc in
random order and then plays all the tracks on each succeeding disc in random order and then stops.
• RANDOM3: Plays 2 tracks randomly from a disc and then
plays 2 tracks randomly from a different disc until all
tracks on all discs have been played.
Note
For two-digit numbers, press the numbered buttons
(0-9)in rapid succession.
DVD
DVD
1 /3
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
Press SKIP/SCAN . or > briefly during
playback to select the next chapter/track or to return
to the beginning of the current chapter/track.
Press . twice briefly to step back to the previous
chapter/track.
To go directly to any chapter/track during DVD
4 to select the
playback, press OSD. Then, press 3/4
chapter/track icon. Then, enter the chapter/track
number using the numbered buttons (0-9).
Search
VCD1.1
1 /3
When a disc has more than one title, you can move to
another title as follows:
Press OSD, then press the appropriate numbered
button (0-9) to select a title number.
DVD
VCD2.0
2 To return to normal playback, press RANDOM until
“RANDOM” disappears on the display window.
Tips
By pressing SKIP/SCAN > during Random playback,
the unit selects another title (track) and resumes
Random playback.
Notes
This function only works with DVD Karaoke discs and
video CD without PBC.
DVD karaoke works only RANDOM 1 function.
On a Video CD with PBC, you must set PBC to Off on
the setup menu to use the Random function. See
page 14.
17
Downloaded From Disc-Player.com Marantz Manuals
OPERATION
DVD
Operation with DVD and Video CD
General Features (continued)
Repeat A-B
A *
A B
DVD
VCD2.0
VCD1.1
OFF
To repeat a sequence in a title :
1 Press A-B at your chosen starting point.
“ A * ” appears briefly on the TV screen.
2 Press A-B again at your chosen end point.
“A B” appears briefly on the TV screen, and the repeat
sequence begins (“AsB” appears the display window).
3 To cancel the sequence, press A-B.
Repeat
CHAPT
DVD
TITLE
VCD2.0
TRACK
VCD1.1
ALL
OFF
DVD Video Discs - Repeat Chapter/Title/All/Off
1 To repeat the currently playing chapter, press
REPEAT.
Time Search
DVD
0:20:09
- :- - : - -
The Time Search function allows you to start playing at
any chosen time on the disc.
1 Press OSD during playback. The on-screen display
appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
4 to select the Time
2 Within 10 seconds, press 3/4
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
3 Within 10 seconds, use the number buttons to enter
the required start time. Enter hours, minutes, and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
4 Within 10 seconds, press SELECT/ENTER to confirm
the start time.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
The Repeat Chapter icon appears on the TV screen.
2 To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3 To repeat entire all disc contents, press REPEAT a third time.
The Repeat All icon appears on the TV screen.
4 To exit Repeat mode, press REPEAT a fourth time.
The Repeat Off icon appears on the TV screen.
Video CDs - Repeat Track/Disc/All/Off
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the TV screen.
2 To repeat the disc currently playing, press REPEAT a
second time.
The Repeat Disc icon appears on the TV screen.
3 To repeat entire all disc contents, press REPEAT a third time.
The Repeat All icon appears on the TV screen.
4 To exit Repeat mode, press REPEAT a fourth time.
The Repeat Off icon appears on the TV screen.
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Repeat function. See page 14.
3D Surround
DVD
VCD2.0 VCD1.1
NORM.
3D SUR
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press OSD during playback.
2 Press 3 or 4 to select the sound option.
The sound option will be highlighted.
3 Press 1 or 2 to to select “3D SUR”.
To turn off the 3D Surround effect, select “NORM”.
Zoom
DVD
VCD2.0
VCD1.1
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
1 Press ZOOM during playback or still playback to activate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to six steps.
2/3
3/4
4 buttons to move through the
2 Use the 1/2
zoomed picture.
3 Press CLEAR to resume normal playback or return to
the paused image.
Note
The zoom function may not work for some DVDs.
18
Downloaded From Disc-Player.com Marantz Manuals
Operation with DVD and Video CD
General Features (continued)
1/9
DVD
VCD2.0
DVD
VCD1.1
MARKER SEARCH
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when
playback reaches the spot that you want to
memorize.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a disc.
To Recall a Marked Scene
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
2 Within 10 seconds, press 1/2 to select a Marker
number that you want to recall.
3 Press SELECT/ENTER.
Playback will start from the Marked scene.
4 To remove the MARKER SEARCH menu, press
SEARCH.
To clear a Marked Scene
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
2 Press 1/2 to select the Marker number that you want
to erase.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
Checking the contents of DVD discs:
Menus
DVDs may offer menus that allow you to access special
features. To use the disc menu, press MENU. Then,
press the appropriate number button to select an option.
2/3
3/4
4 buttons to highlight your selection,
Or, use the 1/2
then press SELECT/ENTER.
Title Menu
DVD
1 Press TOP MENU.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3 To remove the title menu, press TOP MENU again.
Disc Menu
DVD
1 Press MENU.
The disc menu is displayed.
2 To remove the disc menu, press MENU again.
Camera Angle
DVD
1 /1
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
Changing the Audio Language
DVD
1 ENG
D
5.1 CH
Press AUDIO repeatedly during playback to hear a different audio language or audio track.
Changing the Audio Channel
VCD2.0
VCD1.1
Press AUDIO repeatedly during playback to hear a different audio channel (STER., LEFT or RIGHT).
Subtitles
DVD
ABC
1 ENG
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
If
Note
appears, the feature is not available on the disc.
19
Downloaded From Disc-Player.com Marantz Manuals
OPERATION
Marker Search
Special DVD Features
Operation with Audio CD and MP3/WMA Disc
Playing an Audio CD and MP3/WMA Disc
CD
MP3
About MP3
WMA
The DVD Player can play MP3/WMA formatted recordings on CD-ROM, CD-R or CD-RW discs.
Before playing MP3/WMA recordings, read the notes on
MP3/WMA Recordings on right.
Insert a disc and close the tray.
Audio CD; Audio CD menu appears on the TV
screen go to step 4.
MP3/WMA disc; The MP3/WMA-JPEG choice
menu appears on the TV screen. Go to step 2
1
MP3 WMA
JPEG
4 to select the MP3/WMA then press
Press 3/4
2 SELECT/ENTER.
The MP3/WMA menu appears on the TV screen.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
Program
MP3/WMA
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
2
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
00:00
Clear All
OFF
1
3/4
4 to select a folder, and SELECT/ENTER.
3 Press
A list of files in the folder appears.
4 to select a track then press PLAY or
Press 3/4
4 SELECT/ENTER.
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display window and menu.
Playback will stop at the end of the disc.
Press TOP MENU to move to the next page.
Press MENU to move to the previous page.
Program
CD
1
2
3
4
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK 02
TRACK 03
TRACK 04
TRACK 05
TRACK 06
Clear All
TRACK 07
0: 56: 18
Program
MP3/WMA
5
TRACK 01
3
STER.
Notes on MP3/WMA Recordings
NORM.
Audio CD menu
2
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
00:00
Clear All
1
OFF
MP3/WMA menu
Tip 3
If you are in a file list and want to return to the Folder
4 to highlight
list, use the 3/4
and press
SELECT/ENTER to return to the previous menu screen.
5 To stop playback at any other time, press STOP.
20
Downloaded From Disc-Player.com Marantz Manuals
An MP3 file is audio data compressed by using the
MPEG1 audio layer-3 file-coding scheme. We call
files that have the “.mp3” file extension “MP3 files”.
The player can not read an MP3 file that has a file
extension other than “.mp3”.
About WMA(Window Media Audio)
An WMA file is a Microsoft audio compression
technology.
WMA(Windows Media Audio) offers double the audio
compression of the MP3 format.
Microsoft, Windows Media, and the Windows
Logo are trademarks or registered trademarks
of Microsoft Corporation in both the United
States and other countries
MP3/WMA Disc compatibility with this player is
limited as follows:
1. Sampling Frequency / only at 44.1kHz (MP3),
22.05 - 44.1kHz (WMA)
2. Bit rate / within 32 - 320kbps (MP3),
32 - 128kbps (WMA)
3. CD-R physical format should be “ISO 9660”
4. If you record MP3/WMA files using the software
which cannot create a FILE SYSTEM, for example
“Direct-CD” etc., it is impossible to playback
MP3/WMA files. We recommend that you use “EasyCD Creator”, which creates an ISO9660 file system.
5. A single session disc requires MP3/WMA files in the
first track. If there is no MP3/WMA file in the 1st
track, it cannot playback MP3/WMA files. If you wish
to playback MP3/WMA files, format all the data in
the disc or use a new one.
6. File names should be named using 8 letters or less
and must incorporate “.mp3” or “.wma” extension
e.g. “********.MP3” or “********.WMA”.
7. Do not use special letters such as “/ : * ? “ < > ” etc.
8. Total number of files on the disc should be less than
650.
This DVD player requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 or WMA files). That require certain pre-existing
conditions (see above) to insure compatible playback.
Customers should also note that permission is
required in order to download MP3/WMA files and
music from the Internet. Our company has no right
to grant such permission. Permission should
always be sought from the copyright owner.
Caution
– If you record a disc using a personal computer, even if it
is recorded in a compatible format, there are cases in
which it may not play because of the settings of the
application software used to create the disc. (Check with
the software publisher for more detailed information.)
Operation with Audio CD and MP3/WMA Disc (Continued)
CD
MP3
Random with Audio CD
WMA
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
Moving to another Track
CD
MP3
1 Press RANDOM during playback or in stop mode.
The unit automatically begins Random Playback and
“RANDOM(1-3)” appears on the display window.
WMA
Press SKIP/SCAN . or > briefly during
playback to go to the next track or to return to the
beginning of the current track.
Press SKIP/SCAN . twice briefly to step back to
the previous track.
In case of audio CD, to go directly to any track, enter
the track number using the numbered buttons (0-9)
during playback.
Search
CD
MP3
CD
WMA
1 Press and hold SKIP/SCAN . or > for about
two seconds during playback.
The player will now go into SEARCH mode.
2 Press and hold SKIP/SCAN . or > repeatedly
to select the required speed: mX2, mX4, mX8
(backward) or MX2, MX4, MX8 (forward).
Search speed and direction are indicated on the menu
screen.
• RANDOM1: Plays all the tracks on a single disc in random
order and then stops.
• RANDOM2: Plays all the tracks on current disc in
random order and then plays all the tracks on each succeeding disc in random order and then stops.
• RANDOM3: Plays 2 tracks randomly from a disc and then
plays 2 tracks randomly from a different disc until all
tracks on all discs have been played.
2 To return to normal playback, press RANDOM until
“RANDOM” disappears on the display window.
Repeat A-B
CD
To repeat a sequence.
1 During disc playback, press A-B at your chosen starting point.
The Repeat icon and “A * ” appears on the menu screen.
2 Press A-B again at your chosen end point.
The Repeat icon and “A B” appears on the menu screen,
and the sequence begins to play repeatedly.
3 To exit the sequence and return to normal play, press
A-B again.
The Repeat icon and “OFF” appears on the menu screen.
3 To exit SEARCH mode, press PLAY.
Random with MP3/WMA Disc
MP3
WMA
1 Press RANDOM during playback or when playback is
stopped.
The unit automatically begins Random Playback and
RANDOM or “RAND.” appears on the display window
and menu screen.
2 To return to normal playback, press RANDOM repeatedly until RANDOM or “RAND.” disappears on the
display window and menu screen.
Repeat Track/All/Off
MP3
WMA
1 To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the menu
screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat icon and “ALL” appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
The Repeat icon and “OFF” appears on the menu screen.
3D Surround
CD
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press OSD during playback.
2 Use 1 or 2 to select the sound option.
The sound option will be highlighted.
3 Use 3 or 4 to to select “3D SUR”.
To turn off the 3D Surround effect, select “NORM”.
Changing the Audio Channel
CD
Press AUDIO repeatedly during playback to hear a
different audio channel (STER., LEFT, or RIGHT).
Repeat Track/Disc/All/Off
CD
1. To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appear on the menu screen.
2. To repeat all tracks on a disc, press REPEAT a
second time.
The Repeat icon and “DISC” appear on the menu screen.
3.To repeat entire all disc contents, press REPEAT third
time.
The Repeat icon and “All” appears on the menu screen.
4. To cancel Repeat mode, press REPEAT a fourth time.
The Repeat icon and “OFF” appear on the menu screen.
21
Downloaded From Disc-Player.com Marantz Manuals
OPERATION
Pause
Operation with JPEG Disc
Viewing a JPEG disc
Moving to another File
JPEG
This DVD Player can play discs with JPEG files and
Kodak picture CD. Before playing JPEG recordings,
read the notes on JPEG Recordings on right.
1
Insert a disc and close the tray.
The MP3/WMA-JPEG choice menu appears on the
TV screen.
MP3 WMA
Press SKIP/SCAN . or > once during viewing a
picture to advance to the next file or to the previous file.
Still Picture
1 Press PAUSE/STEP during slide show.
The player will now go into PAUSE mode.
2 To return to the slide show, press PLAY or press
PAUSE/STEP again.
To flip the picture
JPEG
4 during showing a picture to flip the
Press 3/4
picture horizontally or a vertically.
3/4
4 to select the JPEG then press
2 Press
SELECT/ENTER.
The JPEG menu appears on the TV screen.
To rotate picture
Press 1/2 during showing a picture to rotate the
picture clockwise or counter clockwise.
JPEG
Folder1
Folder2
Folder3
Folder4
Folder5
Notes on JPEG Recordings
Folder6
Folder7
Folder8
Slide Speed
Off
Depending upon the size and number of the JPEG
files, it could take a long time for the DVD player to
read the disc’s contents. If you don’t see an onscreen display after several minutes, some of the files
are too big — reduce the resolution of the JPEG files
to less than 2 mega pixels and burn another disc.
Total number of files and folders on the disc should
be less than 650.
3/4
4 to select a folder, and SELECT/ENTER.
3 Press
A list of files in the folder appears.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
Tip
If you are in a file list and want to return to the Folder
list, use the 34 buttons on the remote to highlight
“
” and press SELECT/ENTER to return to the
previous menu screen.
Some disc may be incompatible due to different
recording format or condition of disc.
4 to
If you want to view a particular file, press 3/4
4 highlight
a file and press SELECT/ENTER or
PLAY.
When you are using software such as “Easy CD
Creator” to burn the jpeg files into the CD-R, ensure
that all the selected files have the “.jpg” extensions
when copying into the CD layout.
If the files have “.jpe” or “.jpeg” extensions, please
rename them as “.jpg” files.
File names without “.jpg” extension will not be able to
be read by this DVD player. Even though the files are
shown as JPEG image files in windows explorer.
Viewing the file proceeding starts.
During viewing a file, press RETURN to move to
the previous menu (JPEG menu).
Press TOP MENU to move to the next page.
Press MENU to move to the previous page.
JPEG
Folder1
Picture1.jpg
Picture2.jpg
Picture3.jpg
Picture4.jpg
Picture5.jpg
Picture6.jpg
Picture7.jpg
5/32
1024X768
Slide Speed
Off
5/32
1024X768
Picture5.jpg
Tip
There are three viewing Slide Speed options: Fast,
Normal, Slow, and Off. Press 1/2 to highlight the Slide
Speed then press 3/4 to select the option you want to
use, and press SELECT/ENTER.
viewing at any other time, press STOP.
5 ToThestop
JPEG menu appears.
22
Downloaded From Disc-Player.com Marantz Manuals
Caution
– If you record a disc using a personal computer, even if it
is recorded in a compatible format, there are cases in
which it may not play because of the settings of the
application software used to create the disc. (Check with
the software publisher for more detailed information.)
Programmed Playback
CD
VCD2.0
The Program function enables you to store your favorite
tracks from any disc in the player memory.
MP3
WMA
Programmed Playback with MP3/WMA
Programmed Playback with Audio CD
Press PROGRAM during playback or in the stop
mode to enter the Program Edit mode.
The E mark will appear to the right of the word Program
on the right side of the menu screen.
step 1 of “Programmed Playback with
1 Follow
Audio CD ” on left.
a track, then press SELECT/ENTER to
2 Select
place the selected track on the Program list.
step 2 to place additional tracks on the
3 Repeat
Program list.
Program
MP3/WMA
Note
Press PROGRAM to exit the Program Edit mode.
The E mark will disappear.
Move to the Disc number selection column by
pressing 3 repeatedly.
2
3 Select an audio disc number using 1/2.
a track, then press SELECT/ENTER to
4 Select
place the selected track on the Program list.
E
TRACK 8.mp3
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
TRACK
2
1.mp3
2.mp3
3.mp3
4.mp3
5.mp3
6.mp3
7.mp3
8.mp3
TRACK 2.mp3
TRACK 4.mp3
TRACK 3.mp3
Clear All
00:00
OFF
3
MP3/WMA menu
4
Follow steps 6-9 of “Programmed Playback with
Audio CD ” on left.
Programmed Playback with Video CD
Note
3
You must select a disc
number of audio CD.
If selected track is other kind of disc (DVD or MP3 etc.),
the track skips during programmed playback.
steps 2-4 to place additional tracks on
5 Repeat
the Program list.
Program
CD
1
2
3
4
5
E
TRACK 12
2
TRACK 01
TRACK 08
2
TRACK 02
TRACK 10
1
TRACK 03
TRACK 01
3
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Program function. See page 14.
1 Insert Video CD and close the tray.
2 Press PROGRAM while playback is stopped.
The VCD Program menu will appear.
TRACK 04
VCD
TRACK 05
1
TRACK 06
Clear All
TRACK 07
3
0: 56: 18
STER.
Program
2
3
4
5
E
TRACK 04
2
TRACK 01
TRACK 03
2
TRACK 02
TRACK 01
3
TRACK 03
NORM.
TRACK 04
TRACK 05
Audio CD menu
6
Press 2.
7
4 to select the track you want to start
Press 3/4
playing.
The programmed track you selected last is highlighted on
the program list.
Press TOP MENU to move to the next page.
Press MENU to move to the previous page.
8
Press PLAY to start.
9
To resume normal playback from programmed
playback, select a track of CD list and then
press SELECT/ENTER.
Playback begins in the order in which you programmed
the tracks and “PROG.” appears on the menu screen.
Playback stops after all of the tracks on the Program list
have played once.
Clear All
3
0: 56: 18
STER.
NORM.
Video CD menu
Note
Press RETURN or PROGRAM to exit the Program menu.
steps 2-8 of “Programmed Playback with
3 Follow
Audio CD ” on left.
resume normal playback from
4 To
programmed playback, press PROGRAM.
“PROG.” indicator disappears in the display window.
“PROG.” indicator disappears on the menu screen.
23
Downloaded From Disc-Player.com Marantz Manuals
OPERATION
disc
Program can contain 30 tracks.
1
VCD1.1
Programmed Playback
CD
VCD2.0
Repeat Programmed Tracks
To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the menu
screen.
To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat icon and “ALL” appears on the menu screen.
To cancel Repeat mode, press REPEAT a third time.
The Repeat icon and “OFF” appears on the menu screen.
Erasing a Track from Program List
1 Press PROGRAM during playback (Audio CD and
MP3/WMA disc only) or in the stop mode to enter the
Program Edit mode.
The
E
mark will appear.
2 Press 2 to move to the Program list.
4 to select the track that you wish to erase
3 Use 3/4
from the Program list.
4 Press CLEAR.
The track will be erased from the Program list.
Erasing the Complete Program List
1 Follow steps 1-2 of “Erasing a Track from Program
List” as above.
4 to select “Clear All”, then press
2 Use 3/4
SELECT/ENTER.
The complete Program for the disc will be erased.
The programs are also cleared when the disc is removed.
24
Downloaded From Disc-Player.com Marantz Manuals
VCD1.1
MP3
WMA
Additional Information
The screen saver picture appears when you leave the
DVD Player in stop mode for about five minutes.
After the Screen Saver has been engaged for about five
minutes, the DVD Player will automatically turn itself off.
Video Mode Setting
DVD
VCD2.0
VCD1.1
With certain discs, the playback picture may be flickering or Dot Crawl is shown on straight lines. That
means Vertical interpolation or De-interlace is not
perfectly matched with the disc. In this case, the
picture quality may be improved by changing the
video mode.
To change the video mode, press and hold OSD
about 3 seconds during disc playback. The new video
mode number selected is displayed on the TV screen.
Check whether the video quality has improved. If not,
repeat the above procedure until picture quality is
improved.
Video mode change sequence:
MODE1 → MODE2 → MODE3 → MODE1
If you turn off the power, the video mode will be back
to initial state (MODE1).
Setting Remote control codes of
DVD player
• This DVD player support two remote control codes :
C004 and C044.
• When the unit is shipped from the factory, the remote
code is set to C004.
• To set the code of the player to C044, press PAUSE
then input “9872” using number buttons.
• To set the code of the player to C004, press PAUSE
then input “9871” using number buttons.
• You can change the code of the player only when
NO DISC appears in the display window.
• Changed Remote control codes is displayed in the
Display window.
• Set the remote control codes of the Remote control to
the same setting (page 8).
Notes
This setting can not be used if a disc is playing.
If a DVD has been loaded, be sure to press STOP
twice before proceeding.
Detailed Descriptions for Video Modes
MODE1: The source material of the DVD video (film material
or video material) is determined from disc information.
MODE2: Suitable for playing film based content or video based
material recorded by the progressive scan method.
MODE3: Suitable for playing video based content with comparatively little motion.
Note
The video mode setting only works when the Progressive
Scan mode is set to “On” in the Setup menu.
25
Downloaded From Disc-Player.com Marantz Manuals
OPERATION
Screen Saver
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Correction
Cause
Symptom
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD player does
not work.
No disc is inserted.
Insert a disc. (Check that the DVD or,
audio CD indicator in the display
window is lit.)
No picture.
The TV is not set to receive DVD signal
output.
Select the appropriate video input mode
on the TV so the picture from the DVD
player appears on the TV screen.
The video cable is not connected
securely.
Connect the video cable securely.
The connected TV power is turned off.
Turn on the TV.
The equipment connected with the
audio cable is not set to receive DVD
signal output.
Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD player.
The audio cables are not connected
securely.
Connect the audio cable securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The Digital Audio Output is set to the
wrong position.
Set the Digital Audio Output to the
correct position, then turn on the DVD
player again by pressing POWER.
The playback picture is
poor.
The disc is dirty.
Clean the disc.
The DVD player does
not start playback.
No disc is inserted.
Insert a disc. (Check that the DVD, or
audio CD indicator in the DVD display is
lit.)
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type, color system, and Regional code.)
The disc is placed upside down.
Place the disc with the playback side
down.
The disc is not placed within the guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
The Rating level is set.
Cancel the Rating function or change
the rating level.
The remote control is not pointed at the
remote sensor of the DVD player.
Point the remote control at the remote
sensor of the DVD player.
The remote control is too far from the
DVD player.
Operate the remote control within 16 ft
(5 m).
There is an obstacle in the path of the
remote control and the DVD player.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
Remote control code is different
between the DVD player and Remote
control.
Set the remote control codes of both
DVD player and Remote control to the
same setting.
No sound.
The remote control
does not work properly.
26
Downloaded From Disc-Player.com Marantz Manuals
Language Code List
Code
Language
Code
Language
Code
Language
Code
Language
6566
Abkhazian
7074
Fiji
7678
Lingala
8373
Singhalese
6565
Afar
7073
Finnish
7684
Lithuanian
8375
Slovak
6570
Afrikaans
7082
French
7775
Macedonian
8376
Slovenian
8381
Albanian
7089
Frisian
7771
Malagasy
8379
Somali
6577
Ameharic
7176
Galician
7783
Malay
6983
Spanish
6582
Arabic
7565
Georgian
7776
Malayalam
8385
Sudanese
7289
Armenian
6869
German
7784
Maltese
8387
Swahili
6583
Assamese
6976
Greek
7773
Maori
8386
Swedish
6588
Aymara
7576
Greenlandic
7782
Marathi
8476
Tagalog
6590
Azerbaijani
7178
Guarani
7779
Moldavian
8471
Tajik
6665
Bashkir
7185
Gujarati
7778
Mongolian
8465
Tamil
6985
Basque
7265
Hausa
7865
Nauru
8484
Tatar
6678
Bengali; Bangla
7387
Hebrew
7869
Nepali
8469
Telugu
6890
Bhutani
7273
Hindi
7879
Norwegian
8472
Thai
6672
Bihari
7285
Hungarian
7982
Oriya
6679
Tibetan
6682
Breton
7383
Icelandic
8065
Panjabi
8473
Tigrinya
6671
Bulgarian
7378
Indonesian
8083
Pashto, Pushto
8479
Tonga
7789
Burmese
7365
Interlingua
7065
Persian
8482
Turkish
6669
Byelorussian
7165
Irish
8076
Polish
8475
Turkmen
7577
Cambodian
7384
Italian
8084
Portuguese
8487
Twi
6765
Catalan
7465
Japanese
8185
Quechua
8575
Ukrainian
9072
Chinese
7487
Javanese
8277
Rhaeto-Romance
8582
Urdu
6779
Corsican
7578
Kannada
8279
Rumanian
8590
Uzbek
7282
Croatian
7583
Kashmiri
8285
Russian
8673
Vietnamese
6783
Czech
7575
Kazakh
8377
Samoan
8679
Volapük
6865
Danish
7589
Kirghiz
8365
Sanskrit
6789
Welsh
7876
Dutch
7579
Korean
7168
Scots Gaelic
8779
Wolof
6978
English
7585
Kurdish
8382
Serbian
8872
Xhosa
6979
Esperanto
7679
Laothian
8372
Serbo-Croatian
7473
Yiddish
6984
Estonian
7665
Latin
8378
Shona
8979
Yoruba
7079
Faroese
7686
Latvian, Lettish
8368
Sindhi
9085
Zulu
REFERENCE
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 13).
27
Downloaded From Disc-Player.com Marantz Manuals
Country Code List
Enter the appropriate code number for the initial setting “Country Code” (See page 15).
Code
AD
AE
AF
AG
AI
AL
AM
AN
AO
AQ
AR
AS
AT
AU
AW
AZ
BA
BB
BD
BE
BF
BG
BH
BI
BJ
BM
BN
BO
BR
BS
BT
BV
BW
BY
BZ
CA
CC
CF
CG
CH
CI
CK
CL
CM
CN
CO
CR
CS
CU
CV
CX
CY
CZ
DE
DJ
DK
DM
DO
DZ
EC
EE
EG
EH
Country
Andorra
United Arab Emirates
Afghanistan
Antigua and Barbuda
Anguilla
Albania
Armenia
Netherlands Antilles
Angola
Antarctica
Argentina
American Samoa
Austria
Australia
Aruba
Azerbaidjan
Bosnia-Herzegovina
Barbados
Bangladesh
Belgium
Burkina Faso
Bulgaria
Bahrain
Burundi
Benin
Bermuda
Brunei Darussalam
Bolivia
Brazil
Bahamas
Bhutan
Bouvet Island
Botswana
Belarus
Belize
Canada
Cocos (Keeling) Islands
Central African Republic
Congo
Switzerland
Ivory Coast
Cook Islands
Chile
Cameroon
China
Colombia
Costa Rica
Former Czechoslovakia
Cuba
Cape Verde
Christmas Island
Cyprus
Czech Republic
Germany
Djibouti
Denmark
Dominica
Dominican Republic
Algeria
Ecuador
Estonia
Egypt
Western Sahara
28
Downloaded From Disc-Player.com Marantz Manuals
Code
ER
ES
ET
FI
FJ
FK
FM
FO
FR
FX
GA
GB
GD
GE
GF
GH
GI
GL
GM
GN
GP
GQ
GR
GS
GT
GU
GW
GY
HK
HM
HN
HR
HT
HU
ID
IE
IL
IN
IO
IQ
IR
IS
IT
JM
JO
JP
KE
KG
KH
KI
KM
KN
KP
KR
KW
KY
KZ
LA
LB
Country
Eritrea
Spain
Ethiopia
Finland
Fiji
Falkland Islands
Micronesia
Faroe Islands
France
France (European
Territory)
Gabon
Great Britain
Grenada
Georgia
French Guyana
Ghana
Gibraltar
Greenland
Gambia
Guinea
Guadeloupe (French)
Equatorial Guinea
Greece
S. Georgia & S. Sandwich
Isls.
Guatemala
Guam (USA)
Guinea Bissau
Guyana
Hong Kong
Heard and McDonald
Islands
Honduras
Croatia
Haiti
Hungary
Indonesia
Ireland
Israel
India
British Indian Ocean
Territory
Iraq
Iran
Iceland
Italy
Jamaica
Jordan
Japan
Kenya
Kyrgyzstan
Cambodia6
Kiribati
Comoros
Saint Kitts & Nevis Anguilla
North Korea
South Korea
Kuwait
Cayman Islands
Kazakhstan
Laos
Lebanon
Code
LC
LI
LK
LR
LS
LT
LU
LV
LY
MA
MC
MD
MG
MH
MK
ML
MM
MN
MO
MP
MQ
MR
MS
MT
MU
MV
MW
MX
MY
MZ
NA
NC
NE
NF
NG
NI
NL
NO
NP
NR
NU
NZ
OM
PA
PE
PF
PG
PH
PK
PL
PM
PN
PR
PT
PW
PY
QA
RE
RO
RU
RW
SA
SB
Country
Saint Lucia
Liechtenstein
Sri Lanka
Liberia
Lesotho
Lithuania
Luxembourg
Latvia
Libya
Morocco
Monaco
Moldavia
Madagascar
Marshall Islands
Macedonia
Mali
Myanmar
Mongolia
Macau
Northern Mariana Islands
Martinique (French)
Mauritania
Montserrat
Malta
Mauritius
Maldives
Malawi
Mexico
Malaysia
Mozambique
Namibia
New Caledonia (French)
Niger
Norfolk Island
Nigeria
Nicaragua
Netherlands
Norway
Nepal
Nauru
Niue
New Zealand
Oman
Panama
Peru
Polynesia (French)
Papua New Guinea
Philippines
Pakistan
Poland
Saint Pierre and Miquelon
Pitcairn Island
Puerto Rico
Portugal
Palau
Paraguay
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
Saudi Arabia
Solomon Islands
Code
SC
SD
SE
SG
SH
SI
SJ
SK
SL
SM
SN
SO
SR
ST
SU
SV
SY
SZ
TC
TD
TF
TG
TH
TJ
TK
TM
TN
TO
TP
TR
TT
TV
TW
TZ
UA
UG
UK
UM
US
UY
UZ
VA
VC
VE
VG
VI
VN
VU
WF
WS
YE
YT
YU
ZA
ZM
ZR
ZW
Country
Seychelles
Sudan
Sweden
Singapore
Saint Helena
Slovenia
Svalbard and Jan Mayen
Islands
Slovak Republic
Sierra Leone
San Marino
Senegal
Somalia
Suriname
Saint Tome and Principe
Former USSR
El Salvador
Syria
Swaziland
Turks and Caicos Islands
Chad
French Southern
Territories
Togo
Thailand
Tadjikistan
Tokelau
Turkmenistan
Tunisia
Tonga
East Timor
Turkey
Trinidad and Tobago
Tuvalu
Taiwan
Tanzania
Ukraine
Uganda
United Kingdom
USA Minor Outlying
Islands
United States
Uruguay
Uzbekistan
Vatican City State
Saint Vincent &
Grenadines
Venezuela
Virgin Islands (British)
Virgin Islands (USA)
Vietnam
Vanuatu
Wallis and Futuna Islands
Samoa
Yemen
Mayotte
Yugoslavia
South Africa
Zambia
Zaire
Zimbabwe
Specifications
Power requirements
AC 120V , 60 Hz
Power consumption
14W
Dimensions (approx.)
17.3 X 3.2 X 16.2 inches (440 X 80 X 410 mm) (w x h x d)
Mass (approx.)
11.2 lbs (5.1 kg)
Operating temperature
5˚C to 35˚C (41˚F to 95˚F)
Operating humidity
5 % to 90 %
REFERENCE
General
System
Laser
Semiconductor laser, wavelength 650 nm
Signal system
NTSC
Frequency response
DVD (PCM 96 kHz): 8 Hz to 44 kHz
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
Signal-to-noise ratio
More than 100dB (ANALOG OUT connectors only)
Harmonic distortion
Less than 0.008%
Dynamic range
More than 100 dB (DVD)
More than 95 dB (CD)
Outputs
Video output
1 Vp-p 75 Ω, negative sync, RCA jack x 1
S-Video output
(Y) 1.0 V (p-p), 75 Ω, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 Ω
Component Video output
(Y) 1.0 V (p-p), 75 Ω, negative sync, RCA jack x 1
(CB/PB)/(CR/PR) 0.7 V (p-p), 75 Ω, RCA jack x 2
Audio output (coaxial)
0.5 V (p-p), 75 Ω, RCA jack x 1
Audio output (optical)
Optical connector x 1
Audio output (analog 2ch)
2.0 Vrms , 600 Ω, RCA jack (L, R) x 2
Accessories
Video cable . . . . . . . . . . . . . . . . . . . . . . .1
Audio cable . . . . . . . . . . . . . . . . . . . . . . .1
Remote control unit (RC5400VC) . . . . . . .1
Batteries (AAA size) . . . . . . . . . . . . . . . . .2
Warranty card (for USA) . . . . . . . . . . . . .1
Warranty card (for CANADA) . . . . . . . . . .1
User Guide . . . . . . . . . . . . . . . . . . . . . . .1
Design and specifications are subject to change without notice.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
29
Downloaded From Disc-Player.com Marantz Manuals
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
JAPAN
Marantz Japan, Inc.
35-1 Sagami Ohno 7-Chome, Sagamihara-shi, Kanagawa 228-8505, Japan
U.S.A.
Marantz America, Inc.
1100 Maplewood Drive, Itasca, IL 60143, U.S.A.
EUROPE
Marantz Europe B.V.
P.O. Box 8744, 5605 LS Eindhoven, The Netherlands
is a registered trademark.
P/NO: 3834RS0062W
Printed in China
Downloaded From Disc-Player.com Marantz Manuals
03/2003 MIT-lg 31AW851250