Miele DA 371 Technical data

Operating and Installation instructions
Rangehood
DA 2250, DA 2250 EXT
DA 2270, DA 2270 EXT
DA 2210
To avoid the risk of accidents
or damage to the appliance,
it is essential to read these
instructions before it is installed
and used for the first time.
en - AU, NZ
M.-Nr. 09 723 590
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Joystick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To switch the fan on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To select a power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
To switch the fan off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Automatic switch-off of the Intensive setting . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Run-on option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To switch the cooktop lighting on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To dim the cooktop lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To switch the cooktop lighting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Filter operating hours counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fitting and replacing the charcoal filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing a halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Safety distance between cooktop and rangehood. . . . . . . . . . . . . . . . . . . . . . 27
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Operation with Control module DSM 400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Potential free connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Connection to a light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
2
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
or machine
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance or the machine to prevent
misuse.
3
Warning and Safety instructions
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time. They
contain important information on the
safety, installation, use and
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~ This rangehood is designed for
domestic use and for use in similar
environments by guests in hotel or motel
rooms, bed & breakfasts and other
typical living quarters. This does not
include common/shared facilities or
commercial facilities within hotels,
motels or bed & breakfasts.
~ It must only be used to extract
vapours and remove odours from
cooking.
~ This appliance is not suitable for
outdoor use.
Any other usage is at the owner's risk.
Miele cannot be held liable for damage
resulting from incorrect or improper use
or operation.
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
have been given supervision or
instruction concerning its use by a
person responsible for their safety.
Safety with children
~ This appliance is only intended for
use by adults who have read these
instructions. This appliance is not a toy!
To avoid the risk of injury, keep children
well away and do not allow them to play
with it or to use the controls. They will
not understand the potential dangers
posed by it. They should be supervised
whenever you are working in the
kitchen.
~ Older children may use the
rangehood only when its operation has
been clearly explained to them and
they are able to use it safely. They must
be aware of the potential dangers
caused by incorrect operation.
~ Please be aware that on
rangehoods with halogen lighting, the
lamps will get very hot during use and
remain hot for some time after switching
off. To safeguard against burning, keep
children well away from the lamps at all
times.
4
Warning and Safety instructions
Technical safety
~ Before installation, check the
rangehood for visible signs of damage.
Do not install and use a damaged
appliance. A damaged appliance is
dangerous.
~ Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond to the on-site
electricity supply, otherwise the
appliance could be damaged. Consult
a qualified electrician if in any doubt.
~ The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly and, where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~ For safety reasons, this appliance
may only be used when it has been
fully installed.
~ Only open the housing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
~ Installation, maintenance and
repairs may only be carried out by a
suitably qualified and competent
person in strict accordance with current
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
~ Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~ During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:
– it is switched off at the mains fuse,
– the screw-out fuse is removed (in
countries where this is applicable),
– it is switched off at the wall socket
and the plug is withdrawn from the
socket, or it is switched off at the
isolator.
If the appliance is connected via a
plug: Do not pull the mains
connection cable but the mains plug
to disconnect your appliance from
the mains electricity supply.
5
Warning and Safety instructions
~ Do not connect the appliance to the
mains electricity supply via a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~ For appliances with an external fan
motor fitted (...EXT models), the
connection of the two units must be
made using the connection cable and
the plug connectors.
These models may only be combined
with a Miele external motor.
~ This rangehood must not be
installed and operated in mobile
installations (e.g. on a ship).
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the warranty.
~ Great care should be taken when
using the rangehood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas cooktops or ovens which draw air
in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, with or
without an external motor fitted, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
6
Warning and Safety instructions
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the extractor
and the heater are in operation
simultaneously, an underpressure in the
room of 0.04 mbar (4 pa) is the
maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the extractor can only
be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder must be
sought.
If the rangehood is being operated in
recirculation mode, the above
restrictions do not apply.
7
Warning and Safety instructions
Correct use
~ Never use an open flame beneath
the rangehood. To avoid the danger of
fire, do not flambé or grill over an open
flame.
When switched on, the rangehood
could draw flames into the filter. Fat
particles drawn into the rangehood
present a fire hazard.
~ When using the rangehood over a
gas cooktop, ensure that any burners in
use are always covered by a pan.
Switch the cooking zone off when a pan
is removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The rangehood can become damaged
when exposed to excessive heat.
~ Always switch the rangehood on
when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.
~ When cooking with oil or fat, chip
pans and deep fat fryers etc., do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the rangehood on fire.
8
~ Do not use the rangehood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
~ The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~ The rangehood can get very hot
during cooking due to heat rising from
the cooktop.
Do not touch the housing or the grease
filters until the rangehood has cooled
down.
~ Do not use a steam cleaner to clean
this appliance. Pressurised steam
could reach the electrical components
and cause a short circuit.
Warning and Safety instructions
Correct installation
Accessories
~ Refer to the rangehood or cooktop
manufacturer's instructions as to
whether a rangehood may be operated
above the cooktop.
~ Only use genuine Miele spare parts
~ The minimum safety distances
between the top of the cooktop and the
bottom of the rangehood given in the
"Appliance dimensions" section of this
booklet must be maintained, unless the
cooktop manufacturer states that a
greater safety distance is required.
If more than one cooking appliance is
fitted beneath the rangehood, and they
have different minimum safety
distances to the rangehood, select the
greater distance.
and accessories with this rangehood. If
spare parts or accessories from other
manufacturers are used, this will
invalidate the warranty, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
~ Safety regulations prohibit the fitting
of a rangehood over solid fuel stoves.
~ All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from Miele or
from builders' merchants.
~ The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~ If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
9
Guide to the appliance
10
Guide to the appliance
a Control panel
b Joystick
This is used to operate the fan settings
and the lighting.
c Cooktop lighting
d Charcoal filters
Special accessory for recirculation
mode
DA 2250, DA 2270: 2 filters
DA 2210: 4 filters
e Grease filters
f Fan setting indicator lamps
g Touch control for the run-on
option
i Touch control for the charcoal
filter
The indicator lamp for the charcoal filter
lights up when the charcoal filters used
in recirculation mode needs to be
replaced. For this to happen, the
operating hours counter needs to be
activated before the appliance is used
for the first time.
The touch control is used to reset the
operating hours counter every time the
charcoal filters are replaced (see
"Cleaning and care").
It can also be used to check and alter
the operating hours counter.
To activate the run-on option. The fan
can be set to continue running, and to
switch off automatically after either 5 or
15 minutes.
h Touch control for the grease filter
The indicator lamp for the grease filters
lights up when the grease filters need
to be cleaned.
The touch control is used to reset the
operating hours counter every time the
grease filters are cleaned (see
"Cleaning and care").
It can also be used to check and alter
the operating hours counter.
For information about using the
appliance, see "Operation".
11
Modes of operation
The rangehood works with
. . . air extraction:
. . . air recirculation:
The air is drawn in and cleaned by the
grease filters and directed outside.
(requires a conversion kit and charcoal
filters: see "Technical Data")
If the on-site ventilation system does
not have a non-return flap, then the
non-return flap supplied with the
appliance must be fitted in the exhaust
socket in the motor unit.
The air is drawn in and cleaned first by
the grease filters and then by the
charcoal filters (2 on the DA 2250, DA
2270 and 4 on the DA 2210). The
cleaned air is then recirculated back
into the kitchen.
The DA 2210 has two motors and
requires two non-return flaps to be
fitted.
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the rangehood
is switched off.
When the rangehood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
Please note, the performance of
this rangehood hinges greatly on
the installed ducting to vent the
vapours. Poor choice of ducting
results in poor rangehood
performance. For ducting
recommendations, please refer to
the relevant section in these
operating instructions or contact
a specialised installer.
12
Before using the rangehood in
recirculation mode, ensure that the
charcoal filters are in place. See
"Cleaning and care".
. . . an external motor:
(EXT models only)
EXT models are designed to be
connected to an external motor located
outside the room.
The external motor is connected to
the rangehood by means of a
control cable, and is operated by
the controls on the rangehood.
Operation
Joystick
To select a power level
This is used to operate the fan settings
and the lighting.
^ Press the joystick repeatedly to the
right to select a higher power level,
and to the left to select a lower power
level.
To switch the fan on
The relevant power level indicator lamp
will light up.
Depending on the intensity of the
cooking vapours, levels "I" to "III" are
usually sufficient for normal cooking.
Intensive setting
^ Press the joystick once to the right.
For short periods of cooking food with
intensive vapours and a strong aroma,
e.g. when searing meat, you may wish
to select the Intensive Setting "IV".
To switch the fan off
The fan will come on at power level lI.
The second fan power level indicator
lamp will light up.
^ Press the joystick repeatedly to the
left until the fan switches off and the
power level indicator lamps have all
gone out.
or
^ Press and hold the joystick to the left.
The power level indicator lamps will
go out.
13
Operation
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it only runs for 10 minutes before
reverting automatically to level III.
^ To set this option, both the fan and
the cooktop lighting must be
switched off.
^ Press the run-on option control for
approximately 10 seconds. The first
power level indicator lamp will light
up.
^ Press the joystick
– once to the rear or to the front. The
second indicator lamp will light up,
– then press the joystick once to left.
The third indicator lamp will light up,
– then press the joystick once to the
left or to the front.
The indicator lamps for fan power levels
I and IV will flash if the automatic
switch-off for the Intensive setting is not
activated.
^ To activate automatic switch-off,
press the joystick once to the right.
The indicator lamps for power levels
"I" and "IV" will light up constantly.
^ To deactivate automatic switch-off,
press the joystick once to the left.
^ Press the control for the run-on
option to confirm the selection and
to come out of programming mode.
14
Run-on option
It is advisable to run the fan for a few
minutes after cooking has finished to
neutralise any lingering odours in the
air, whether you are using air extraction
or recirculation mode.
The fan can be set to switch off
automatically after either 5 or 15
minutes.
^ After cooking has finished, press the
run-on option control whilst the fan is
still running.
– Press once = The fan will switch off
after 5 minutes (left-hand indicator
lamp).
– Press twice = The fan will switch off
after 15 minutes (right-hand indicator
lamp).
^ To switch off the run-on option, press
the run-on option control again. The
appliance will then not switch off
automatically.
Operation
To switch the cooktop lighting on
To switch the cooktop lighting off
The cooktop lighting can be switched
on and off independently of the fan.
^ Press the joystick again once to the
rear or to the front to switch it off.
Safety cut-out
Should the rangehood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
^ Pressing the joystick once to the right
will switch the fan back on again.
^ Press the joystick once to the rear or
to the front to switch it on.
To dim the cooktop lighting
The brightness of the lighting can be
adjusted.
^ With the lighting switched on, press
and hold the joystick to the rear or
the front.
The brightness will gradually dim until
you release the joystick.
^ Pressing and holding it again will
gradually increase the brightness
until you release it.
^ If you keep the joystick pressed in,
the light will continually change
between bright and dim.
15
Operation
Filter operating hours counter
The number of hours the appliance has
been in operation is stored in memory.
The operating hours counter tells you
when the grease filters or charcoal
filters need to be cleaned or replaced.
Reading the grease filter operating
hours counter
To check the percentage of time set
already used:
^ Switch the fan on with the joystick.
Resetting the grease filter operating
hours counter
^ Press and hold the grease filter
control.
After 30 hours of operation (or another
time if the operating hours counter has
been altered), the grease filter indicator
lamp will light up. The grease filters
must then be cleaned.
Afterwards, the grease filter operating
hours counter must be reset.
^ To do this, press and hold the grease
filter control for approximately
3 seconds while the fan is switched
on.
The indicator lamp for the grease filter
control will go out.
16
One or several of the power level
indicator lamps will flash.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
2 lamps
3 lamps
4 lamps
= 25 %
= 50 %
= 75 %
= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
Operation
Altering the grease filter operating
hours counter
The operating hours counter for the
grease filter is set at the factory for 30
hours. This can be lengthened or
shortened to suit the type of cooking
you do. You can choose 20, 30, 40 or
50 hours.
– Select a short time if you roast or fry
a lot.
– If you use very little fat for cooking,
select a longer time.
– If you only cook occasionally, we
recommend that you still select a
short time because grease which has
built up gradually over a long period
of time will harden on the filter and
make cleaning more difficult.
^ Switch the fan off with the joystick.
^ Use the joystick to select the time
required.
Press to the left for a shorter
operating time, or to the right for a
longer time.
^ Confirm the selection by pressing the
grease filter control.
All the indicator lamps will go out.
^ Press the run-on option control and
the grease filter control at the same
time.
If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the "old" data.
The indicator lamp for the grease filter
touch control and one of the power
level indicator lamps will flash.
The power level indicator lamps show
the time which has been set:
1st lamp from the left = 20 hours
2nd lamp from the left = 30 hours
3rd lamp from the left = 40 hours
4th lamp from the left = 50 hours
17
Operation
Activating and altering the charcoal
filter operating hours counter
(in recirculation mode)
The charcoal filters must be fitted for
the rangehood to be used in
recirculation mode.
On delivery, the operating hours counter
for the charcoal filter is deactivated.
For recirculation mode, the operating
hours counter needs to be set to suit
the type of cooking you do:
^ Switch the fan off with the joystick.
^ Press the run-on option control and
the charcoal filter control at the same
time.
The indicator lamp for the charcoal filter
control and one of the power level
indicator lamps will flash.
The power level indicator lamps show
the time which has been set:
1st lamp from the left = 120 hours
2nd lamp from the left = 180 hours
3rd lamp from the left = 240 hours
4th lamp from the left = unlimited
18
^ Use the joystick to select the time
required.
Press to the left for a shorter
operating time, or to the right for a
longer time.
^ Confirm the selection by pressing the
charcoal filter control.
All the indicator lamps will go out.
If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the "old" data.
Operation
Resetting the charcoal filter
operating hours counter
Reading the charcoal filter operating
hours counter
To check the percentage of time set
already used:
^ Switch the fan on with the joystick.
The indicator lamp for the charcoal filter
control will light up after the rangehood
has operated for the number of hours
set. The charcoal filters must be
replaced with new ones.
Afterwards, the charcoal filter operating
hours counter must be reset.
^ Press and hold the charcoal filter
control for about 3 seconds while the
fan is switched on.
The indicator lamp for the charcoal filter
control will go out.
^ Press and hold the charcoal filter
control.
One or several of the power level
indicator lamps will flash.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
2 lamps
3 lamps
4 lamps
= 25 %
= 50 %
= 75 %
= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
19
Cleaning and care
,Before any cleaning or
maintenance work is carried out,
disconnect the rangehood from the
mains supply. Ensure that:
– it is switched off at the isolator,
or
– it is switched off at the wall
socket and the plug removed, or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed
(in countries where this is
applicable).
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents.
These will damage the surface
material.
Grease filters
A range of Miele branded cleaning and
conditioning agents are available to
order through your Miele Chartered
Agent, from Miele or via the internet at
www.miele-shop.com.
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
rangehood.
Housing
The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
^ All external surfaces and controls can
be cleaned using the Original Miele
all purpose microfibre cloth, or with
warm water and a small amount of
washing-up liquid applied with a well
wrung-out soft sponge or cloth.
^ Wipe the surfaces dry using a soft
cloth.
20
To avoid a build-up of grease, the
grease filters should be cleaned
regularly (at least every 3-4 weeks), but
always clean immediately if the grease
filter indicator lamp comes on.
,An oversaturated filter is a fire
hazard.
Cleaning and care
Cleaning the grease filters in the
dishwasher
^ Place the filters as upright as
possible in the lower basket, with the
short sides upright, and wash on a
65°C programme, ensuring the spray
arm is not obstructed. If a Miele
dishwasher is being used, select the
Sensor wash programme.
^ Use a mild dishwasher detergent.
^ To take out the grease filters, release
the locking clip on the filter, lower the
filter 45°, unhook it at the back and
remove it.
To avoid damaging the filters or the
cooktop below, make sure you hold
the filters securely at all times when
handling them.
Cleaning the grease filters by hand
^ Clean the filters with a soft nylon
brush in a mild solution of hot water
and a small amount of washing-up
liquid.
Do not use undiluted washing-up
liquid.
Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.
After cleaning, leave the filters to dry on
an absorbent surface before replacing
them.
When removing the filters for cleaning,
also clean off any residues of oil or fat
from the now accessible housing to
prevent the risk of these catching fire.
Do not use:
– cleaning agents containing
descaling agents,
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
– oven sprays.
When putting the grease filters back in
position, ensure that the locking clips
are facing down towards the cooktop.
^ If a grease filter is inadvertently
replaced upside down, insert a small
screwdriver blade into the slit to
disengage the clip.
21
Cleaning and care
^ After replacing the grease filters,
press the grease filter control for
approximately 3 seconds to reset the
operating hours counter.
The indicator lamp will go out.
^ If the grease filters are cleaned
before the operating hours counter
has reached its maximum, the grease
filter control should be pressed for
approximately 6 seconds to reset the
counter.
Fitting and replacing the
charcoal filters
If the rangehood is connected for
recirculation, charcoal filters must be
inserted in addition to the grease filters.
They are designed to absorb cooking
odours and are fitted in the canopy
above the grease filters.
DA 2250, DA 2270: 2 charcoal filters
DA 2210: 4 charcoal filters
New filters can be purchased from
your Miele Chartered Agent or from
Miele. See back cover for contact
details, and "Technical data" for the
model number of the filter.
^ Before fitting or replacing the
charcoal filters, the grease filters
must first be taken out (see previous
section for instructions on how to do
this).
^ Unwrap the charcoal filters.
22
^ Insert the charcoal filters into the
canopy.
^ When fitting for the first time:
Activate the charcoal filter operating
hours counter to suit your
requirements (see "Operation").
^ Replace the grease filters.
Cleaning and care
Always replace the charcoal filters immediately if
– the indicator lamp for the charcoal
filter control lights up,
or
– they are no longer effective in
absorbing kitchen odours.
They should, however, be replaced at
least every 6 months.
Used charcoal filters can be disposed
of with the normal household waste.
^ After fitting the new charcoal filters,
press the charcoal filter touch control
for approximately 3 seconds to reset
the operating hours counter.
The charcoal filter indicator lamp will
go out.
^ If the charcoal filters are replaced
before the operating hours counter
has reached its maximum, the
charcoal filter control should be
pressed for approximately 6 seconds
to reset the counter.
23
Cleaning and care
Changing a halogen lamp
Before any cleaning or maintenance
work is carried out, disconnect the
rangehood from the mains supply.
Ensure that:
– it is switched off at the isolator,
or – it is switched off at the wall
socket and the plug removed,
or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed
(in countries where this is
applicable).
^ Remove the grease filter.
^ Remove the charcoal filters if the
rangehood is being used in
recirculation mode.
,Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off.
Do not touch the surface directly
when changing a lamp, as grease
particles from your fingers will
adhere to the surface and damage
it. Please follow the manufacturer's
instructions.
^ Push down the lighting unit slightly
via the opening in the safety panel.
^ The halogen lamp is now accessible
and should be unscrewed
anti-clockwise.
^ Replace it with a new halogen lamp
(specification: GU/GZ 10, 230 V,
50 W). Screw the lamp into the
socket and push it upwards.
Please follow the manufacturer's
instructions.
We recommend only using lamps of the
same specification and also made by
the same manufacturer as the ones
being replaced.
^ Replace the grease filter and, if being
used in recirculation mode, the
charcoal filters.
24
After sales service
In the event of a fault which you cannot
correct yourself, please contact:
– Miele
You will find the telephone number
and address of Miele on the back
cover of the manual.
Please quote the model and serial
number when contacting Miele. These
are shown on the data plate which is
visible when the grease filters are
removed.
Warranty
The warranty for this appliance is
2 years.
For further information, please refer to
your warranty booklet.
25
Appliance dimensions
*Cut-out dimensions
A depth T of at least 25 mm must be
provided at the back of the building-in
niche.
26
Appliance dimensions
Safety distances between cooktop
and rangehood (S)
The minimum safety distances
between the top of a cooktop and
the bottom of the rangehood are
as follows, unless a greater
distance is specified by the
manufacturer of your cooking
appliance:
Cooking appliance
Distance
S
Electric cooktop
600 mm
Open electric grill
650 mm
Deep fat fryer (electric)
650 mm
Multi-burner gas cooktop
with maximum 45.4 MJ/h
total output, with no burner
having a greater output
than 16.2 MJ/h.
650 mm
Multi-burner gas cooktop
with total output greater
than 45.4 MJ/h, or a gas
cooktop including a single
burner with an output
greater than 16.2 MJ/h.
760 mm
Single gas cooktop with a
maximum output of
21.6 MJ/h
650 mm
Single gas cooktop with a
maximum output greater
than 21.6 MJ/h
760 mm
– When deciding on the safety distance
between the cooktop and rangehood,
please note that a distance of
650 mm above electric cooktops may
be preferable to give more working
space under the rangehood.
– Account should also be taken of the
height of the person who will be
using the rangehood most often. The
person should have sufficient space
to work comfortably at the cooktop,
and also be able to reach the
rangehood controls with ease.
– If positioned too high, extraction will
be inefficient.
See "Warning and Safety"
instructions for further information.
27
Installation
Fitting the non-return flap
(not needed for recirculation mode)
^ Place the appliance in the cut-out
from below and align it.
^ If a non-return flap is not present in
the venting system, the non-return
flap supplied must be fitted onto the
exhaust socket in the motor unit. The
flaps must open upwards.
DA 2250, DA 2270: 1 non-return flap
DA 2210: 2 non-return flaps
^ Secure the rangehood by the frame
using 3.5 x 16 mm screws.
Building in
The rangehood is designed for
installation in wall units, rangehood
housing units, and above breakfast
bars or island areas.
Check prior to installation that the top of
the appliance will be accessible after
installation.
If this is not the case, install the exhaust
ducting and prepare the electrical
connection before installation.
28
^ Before using the appliance for the
first time, take the grease filters out
and remove the protective foil from
the filter frame. Then replace the
grease filters.
Installation
Preparation for extraction
^ See "Connection for air extraction" for
further instructions on fitting the
ducting.
^ DA 2210: The rangehood has two
exhaust connections for use with two
150 mm diameter exhaust hoses.
A Y- adapter is supplied with the
rangehood. It may be used to feed
the exhaust from both connections to
a 200 mm diameter common duct.
^ When using C 150 mm ducting,
secure the exhaust connection
supplied to exhaust ducting with
hose clips.
^ Place the exhaust ducting on the fan
connection for the rangehood.
29
Installation
Recirculation
A non-return flap is not used in
recirculation mode.
^ Take the on-site conditions into
account when fitting the conversion
kit.
When fitting the exhaust grille, make
sure that the slats in the grille point
towards the centre of the room and
not directly towards a wall or the
ceiling.
^ Fit the charcoal filters and set the
filter operating hours counter (see
"Cleaning and Care").
If site conditions are not suitable for the
rangehood to be used with air
extraction, the appliance must be set
up for recirculation.
For this, conversion kit DUU 151
(available from your Miele Chartered
Agent or Miele ) is required. One
conversion kit is required for the
DA 2250 and 2270, and two kits for the
DA 2210.
You will also require two charcoal filters
for the DA 2250 and 2270, or 4
charcoal filters for the DA 2210 (see
"Technical data").
30
Installation
Fitting the joystick
4. Then tighten the screw with a 3 mm
allen key. Continue to counterhold
the joystick with an SW 9 spanner.
Do not turn the spanner.
Joystick extension
The joystick can be extended if
required (special accessory - Miele
DBV 100).
1. Screw the spring into the holder and
tighten by hand. Whilst doing so,
counterhold the joystick with an SW 9
spanner. Do not turn the spanner!
2. Then fit the middle section onto the
spring and tighten by hand whilst
continuing to counterhold the
joystick. Do not turn the spanner.
3. Then fit the lower section of the
joystick and lightly secure in position
with the screw supplied and a spring
washer. Do not tighten the screw yet.
Turn the lower section around, until
the m symbol is facing the front.
^ Assemble the spring and top section
as described above.
^ Whilst counterholding the joystick
with an SW 9 spanner (do not turn),
secure the joystick extension to the
top section.
^ Then attach the lower section of the
joystick to the extension piece as
previously described, turn the m
symbol to the front and then tighten
the screw.
31
Installation
Electrical connection
^ If the rangehood is to be connected
to an external motor (EXT models):
Use the connection cable with 6 pole
plug to connect the rangehood and
the external motor.
^ Connect the appliance to the mains
via a fused socket.
Before connecting the appliance,
read the safety notes in "Warning
and Safety instructions" and
"Electrical connection".
32
Connection for air extraction
Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the rangehood at the same time as
another heating appliance which
relies on air from the same room.
The rangehood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for the extraction ducting.
– When using an external motor, make
sure that the exhaust ducting is
sufficiently rigid. The external motor
can cause an underpressure which
can result in the exhaust ducting
distorting.
To achieve the greatest possible air
extraction with the lowest noise level,
please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
– Only use rigid ducting fixed into
place.
– If flat ducting is being used, the
cross-section must not be smaller
than the cross-section of the exhaust
connection.
If exhaust ducting with a diameter of
less than 150 mm, or if flat ducting
or highly flexible ducting is used, the
noise level of the rangehood will
increase and extraction will be less
efficient.
– All ducting, pipework and fittings
must be of non-flammable materials.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
– The exhaust ducting should not be
kinked or compressed.
– Ensure that all connections are
strong and airtight.
33
Connection for air extraction
– Where ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the rangehood.
Condensate trap
(optional accessory)
– If the exhaust air is to be ducted into
the open air, the installation of a
telescopic wall vent or roof vent
(available as an optional accessory)
is recommended.
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
Important:
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
For installations in areas where the
exhaust ducting is exposed to cold
temperatures, we recommend
insulating the exhaust ducting and
installing a condensate trap to collect
and evaporate any condensate which
may occur. Condensate traps are
available for C 125 mm or C 150 mm
ducting.
When installing a condensate trap,
ensure that it is positioned vertically
and, if possible, directly above the
exhaust connection. The arrow on the
housing indicates the direction of
air-flow.
rangehoods designed for use with an
external motor (...EXT models) have an
integrated condensate trap.
34
Connection for air extraction
Silencer
...with air extraction:
(DASD 150 optional accessory)
The silencer not only reduces noise
from the fan, but also sounds from
outside (e.g. traffic noise).
For this reason, the silencer must be
positioned as close as possible to where
the ducting leaves the building a.
...in recirculation mode:
The silencer needs to be positioned
between the fan and the exhaust grille
b. The space needs to be checked in
some cases.
To achieve even further reductions in
noise levels, a special silencer can be
fitted in the ducting system.
...air extraction with external fan:
To minimise noise from the fan in the
kitchen, the silencer should be
positioned in front of the external fan c
if possible, or if the ducting is long, then
in the ducting inside the rangehood
itself d.
In the case of an external fan placed
inside the house, fitting a silencer
behind the external fan e reduces the
noise of the fan outside the house.
In all modes of operation, the most
effective noise reductions are
achieved if two silencers are fitted in
the system.
35
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
Connection of this appliance should be
made via a suitable isolator which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
36
If the switch is not accessible after
installation, an additional means of
disconnection must be provided for all
poles.
For extra safety, it is advisable to install
a suitable residual current device
(RCD). Contact a qualified electrician
for advice.
Important
This appliance is supplied for
connection to an AC 230 V single
phase 50 Hz supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
Brown
= live
WARNING:
THIS APPLIANCE MUST BE
EARTHED
If the connection cable is damaged, it
must be replaced by the manufacturer
or similarly qualified persons to avoid a
hazard.
Operation with Control module DSM 400
The Miele DSM 400 control module can
be used to combine the rangehood with
other components.
It enables the following:
Potential free connection
This is used for controlling another
appliance with the help of the
rangehood's On/Off button s.
The components of the central
extraction system are not supplied as
standard by Miele.
If in any doubt, the advice of a
competent builder must be sought.
Connection to a light switch
The control module can be used to
switch on the rangehood lighting and
also to dim it, depending on model, via
a light switch in the house.
Installation
The control module is fitted onto the
rangehood housing.
All electrical work must be carried
out by a competent, qualified
electrician.
The potential free contact of the
DSM 400 a can be installed in an
...EXT model, for instance, which is
connected to a central extraction
system.
The contact can be used to activate a
motorised shut-off flap b which is
installed before the central extraction
system c.
37
Technical data
Total rated load*
DA 2250, DA 2270. . . . . . . . . . . . 300 W
DA 2210. . . . . . . . . . . . . . . . . . . . 780 W
– Fan motor
DA 2250, DA 2270 . . . . . . . . . . 200 W
DA 2210 . . . . . . . . . . . . . . . 2 x 290 W
– Cooktop lighting
DA 2250, DA 2270 . . . . . . . . 2 x 50 W
DA 2210 . . . . . . . . . . . . . . . . 4 x 50 W
Voltage . . . . . . . . . . . . . . . . . AC 230 V
Frequency . . . . . . . . . . . . . . . . . . 50 Hz
Fuse rating GB . . . . . . . . . . . . . . . . . 5 A
Fan performance*
Extraction power according to EN 61591
DA 2250, DA 2270:
Extraction system C 150 mm
Level I . . . . . . . . . . . . . . . . . . . 200 m3/h
Level II. . . . . . . . . . . . . . . . . . . 300 m3/h
Level III . . . . . . . . . . . . . . . . . . 400 m3/h
Level IV Intensive Setting . . . . 640 m3/h
Recirculation with charcoal filter:
Level I . . . . . . . . . . . . . . . . . . . 140 m3/h
Level II. . . . . . . . . . . . . . . . . . . 240 m3/h
Level III . . . . . . . . . . . . . . . . . . 360 m3/h
Level IV Intensive Setting . . . . 550 m3/h
AUS, NZ:
Plug rating . . . . . . . . . . . . . . . . . . . 10 A
Test marks . . . . . . . . . . Electrical safety
. . . . . . . . . . . . . . . . . . . . . . C-Tick Mark
Electrically suppressed
according to AS/NZS 1044
Electrical cable length . . . . . . . . . 1.5 m
Weight
DA 2250 . . . . . . . . . . . . . . . . . . . . . 8 kg
DA 2250 EXT . . . . . . . . . . . . . . . . 5.5 kg
DA 2270. . . . . . . . . . . . . . . . . . . . 9.5 kg
DA 2270 EXT . . . . . . . . . . . . . . . . . 7 kg
DA 2210 . . . . . . . . . . . . . . . . . . . . 16 kg
DA 2210:
Extraction system 2 x C 150 mm
Level I . . . . . . . . . . . . . . . . . . . 650 m3/h
Level II. . . . . . . . . . . . . . . . . . . 950 m3/h
Level III . . . . . . . . . . . . . . . . . 1250 m3/h
Level IV Intensive Setting . . . 1850 m3/h
Recirculation with charcoal filter:
Level I . . . . . . . . . . . . . . . . . . . 600 m3/h
Level II. . . . . . . . . . . . . . . . . . . 900 m3/h
Level III . . . . . . . . . . . . . . . . . 1200 m3/h
Level IV Intensive Setting . . . 1550 m3/h
Special accessory for recirculation
mode:
* For EXT models,
– Conversion kit DUU 151
2 kits are required for the DA 2210
the rated load and extraction power will
depend on the type of external motor
fitted.
– Miele charcoal filter pack DKF 15-1
(each pack contains 2 filters)
2 packs are required for the
DA 2210
38
Length of connection cable to external
motor. . . . . . . . . . . . . . . . . . . . . . . 1.9 m
39
Alteration rights reserved / 3313
M.-Nr. 09 723 590 / 00