Viking 301 Series Specifications

Installation
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information, call 1-888-VIKING1 (845-4641)
or visit the Viking Website at vikingrange.com
UL
F20886 EN
C
UL
201/301 Series
Built-In Dishwashers
(040312)
Table of Contents
IMPORTANT– Please Read and Follow
Warnings & Important Information _____________________________________________________3
Dimensions & Cutout Dimensions _____________________________________________________6
Specifications _______________________________________________________________________7
General Information__________________________________________________________________8
Site Preparation__________________________________________________________________8
Water Supply ____________________________________________________________________8
Drain ___________________________________________________________________________8
Electrical Connections________________________________________________________________9
Hardwire Conduit Option _______________________________________________________10
Counter Balance Spring Adjustment ______________________________________________12
Installation _____________________________________________________________________13
Leveling _______________________________________________________________________14
Final Installation ________________________________________________________________15
Performance Checklist ______________________________________________________________17
Testing for Leaks ________________________________________________________________17
Final Preparation________________________________________________________________17
Service & Registration _______________________________________________________________18
• Before beginning–please read these
instructions completely and carefully.
• Please ensure that this product is properly
grounded.
• DO NOT remove permanently affixed
labels, warnings, or rating plates from the
dishwasher. This may void warranty or
create an unsafe product.
• The installer should leave these
instructions with the consumer who should
retain for local inspector’s use and for
future reference.
• Please observe all national and local
codes.
• The dishwasher has a factory installed
backflow preventer. DO NOT add an
additional check valve.
WARNING
Make sure that incoming voltage is the
same as unit rating. An electric rating
plate specifying voltage, hertz, and amps
is attached to the product. Wiring the
dishwasher with more voltage than it is
rated for may cause severe damage. To
reduce the risk of fire, electric shock, or
injury to persons, installation work and
electrical wiring must be done by qualified
technician in accordance with all
applicable codes and standards, including
fire-rated conditions.
• Failure to provide a 20” above floor level
(50.8 cm) high loop may result in improper
operation of the dishwasher.
• Remove pallet screws from base. Damage
could occur to dishwasher if screws are not
removed.
WARNING
Plumbing connections must comply with
applicable sanitary, safety and plumbing
codes.
WARNING
WARNING
Electrical power must be turned off at
circuit breaker or fuse box before making
electrical connections. Disconnect the
electrical power supply and place a tag at
the disconnect switch indicating that you
are working on the circuit.
Site Preparation
2
The dishwasher door may not stay open
by itself until the door panel is installed.
Be aware of this when fastening the
dishwasher to the cabinet.
It is recommended that a thorough site inspection be
conducted PRIOR to unpacking and moving this appliance.
3
IMPORTANT–Please Read and Follow!
WARNING
WARNING
ELECTRICAL SHOCK HAZARD
Disconnect the electrical power supply and
place a tag at the disconnect switch
indicating that you are working on the
circuit.
• Electrically ground dishwasher.
• Connect ground wire to green ground
connector in terminal box.
• DO NOT use an extension cord.
• Failure to follow these instructions, can
result in death, fire or electrical shock.
WARNING
Be sure electrical power is turned off at
circuit breaker or fuse box before servicing
or installing unit. DO NOT use an
extension cord for this appliance.
WARNING
TIP OVER HAZARD
• DO NOT use dishwasher until
completely installed.
• DO NOT push down on open door.
• Doing so can result in serious injury
or cuts.
WARNING
Improper connection of the equipment –
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or serviceman if you are in
doubt as to whether the appliance is
properly grounded. DO NOT modify the
plug provided with the appliance; if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
WARNING
EXCESSIVE WEIGHT HAZARD
Use two or more people to move and
install dishwasher. Failure to do so can
result in back or other injury.
IMPORTANT– Please Read and Follow
A GFI shall be used if required by NFPA-70
(National Electric Code), federal/state/local
laws, or local ordinances.
• The required use of a GFI is normally
related to the location of a receptacle with
respect to any significant sources of water
or moisture.
• Viking Range Corporation will NOT
warranty any problems resulting from GFI
outlets which are not installed properly or
do not meet the requirements below.
If the use of a GFI is required, it should be:
• Of the receptacle type (breaker type or
portable type NOT recommended)
• Used with permanent wiring only
(temporary or portable wiring NOT
recommended)
• On a dedicated circuit (no other
receptacles, switches or loads in the
circuit)
• Connected to a standard breaker of
appropriate size (GFI breaker of the same
size NOT recommended)
• Rated for Class A (5 mA +/- 1 mA trip
current) as per UL 943 standard
• In good condition and free from any
loose-fitting gaskets (if applicable in
outdoor situations)
• Protected from moisture (water, steam,
high humidity) as much as reasonably
possible
WARNING
Plumbing connections must comply with
applicable sanitary, safety, and plumbing
codes.
CAUTION
The dishwasher has a factory installed
backflow preventer. DO NOT add an
additional check valve.
4
5
Dimensions & Cutout Dimensions
Specifications
Built-In Dishwasher
Description
23
(60-7/8
.6 ”
cm
)
”
24 cm)
.0
(61
2
(61 4”
.0
cm
)
Overall height from floor
Overall depth from rear
-7/ )
33.0 cm
(86
86 in
.4
cm .
35 to )
”
(89 mi
.0 n.
cm
)
4”
-3/cm)
8
2
.0
(73
Note: A 2” (5.1 cm)
cut-out is required
for water supply
and discharge lines.
301 Models
23-7/8” (60.6 cm)
33-7/8” (86.0 cm) min. to 35” (89.0 cm) max.
Cutout width
To edge of side – 23-5/8” (60.0 cm) – includes door panel
To front of door handle – 26-3/8” (67.0 cm)
With door open – 49” (124.5 cm)
24” (61.0 cm)
Cutout height
34” (86.4 cm) min. to 35” (89.0 cm) max.
8”
34
”m
(
201 Models
Overall width
Cutout depth
Electrical requirements
Water-heating element rating
Inlet water temperature
24” (61.0 cm)
15.0 amps, 120VAC/60 Hz;
3’9” (1.1 m) electrical cord 3 prong plug supplied with unit.
1200 watts
120°F (49°C) required
120°F (49°C) required
”
49 cm)
4.5
(12
Inlet water pressure
operating range
Inlet water hose
Drain hose
D3
26-3/8”
Drain hose high loop required
(67.0 cm)
Approximate shipping weight
10 to 125 psi (0.69 to 8.62 bar)
5’ (1.5 m) braided stainless steel water line with 3/8” (0.95 cm) compression
fitting connected to dishwasher
7’ (2.13 m) 1/2” (1.3 cm) ID “crimp-proof” flexible drain hose attached to
dishwasher, connections provided for 5/8” (1.6 cm), 3/4” (1.9 cm) or
1” (2.5 cm), cut as required
Height from floor – 20” (51.0 cm) min.
147 lbs. (66.7 kg)
23-5/8”
(60.0 cm)
2-3/4”
(7 cm)
6
7
152 lbs. (68.9 kg)
General Information
Electrical Connections
• Read these instructions carefully and
completely before installing the
dishwasher. The installation should be
carried out by a qualified installer, who is
familiar with all local codes and ordinances
for electrical and plumbing connections. If
the dishwasher is being installed for the
first time, most of the work has to be done
before you move it into place. If you are
replacing an old dishwasher, you must
check the old connections.
• Electrical requirements are listed in the
“Specifications” section.
• For service convenience, a shut-off valve
(not supplied) should be installed in the
supply line in a readily accessible location
(such as beneath the sink).
• It is recommended that the dishwasher
be connected to a hot water supply.
• It is important that the water supply line
and the shut-off valve have a sufficient flow
volume. Flush the supply line prior to
connecting it to the intake line of the
dishwasher.
• Make sure the connection is sealed and not
leaking before completing the installation.
Grounding Instructions
Site Preparation
Drain
Note: It is recommended that a thorough
site inspection be conducted PRIOR to
unpacking and moving this appliance.
• After determining where the water
supply line will connect to the
dishwasher, provide a 2” (5.1 cm) access
hole and run the line to the approximate
fill valve location. Sealing access area
once lines are in place is recommended.
• Confirm available access to adequate power.
• The access hole for the drain line should
be 2” square (5.1 cm). Locate as low and
as near to the back wall as possible.
• DO NOT use any fittings anywhere in the
drain line that are less than 1/2” (1.3 cm) ID.
• If the drain line is going to be connected
to a food waste disposer, be sure to
remove the knockout or plug from the
fitting before connecting drain line.
• Drain connection should be a minimum of
9” (22.9cm) from the floor. If connection is
lower, siphoning during cycle can occur.
Water Supply
The dishwasher has a factory installed
backflow preventer. DO NOT add an
additional check valve.
Plumbing connections must comply with
applicable sanitary, safety, and plumbing
codes.
Note: The end of the drain hose is 1” (2.5 cm),
but is adjustable to 3/4” (1.9 cm) or 5/8”
(1.6 cm). If the drain connection is smaller
than 1” (2.5 cm), the hose can be cut to fit
the connection.
• Water pressure for the water supply should
be a minimum of 10 to 125 psi. The
dishwasher is supplied with a 5’ (1.5 m)
braided stainless steel water line with 3/8”
(0.95 cm) compression fitting connected to
dishwasher.
• After determining where the water supply
line will connect to the dishwasher, provide
a 2” (5.1 cm) access hole and run the
water supply line to the approximate fill
valve location.
Note: Be sure to run the drain line through
the hole to the sink compartment before
moving the dishwasher into place.
8
This appliance must be grounded. In the
event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an
appropriate outlet that is installed and
grounded in accordance with all local codes
and ordinances.
WARNING
CAUTION
WARNING
4. Care should be exercised, when the
appliance is installed or removed to
reduce the likelihood of damage to the
power supply cord.
• The dishwasher comes with a 3’9” (1.1 m)
electrical cord for 110-120 volts, 15/20
amp supply. This cord should be plugged
into the 110-120 volt outlet located under
the sink.
• If the cord is not long enough or if a hard
wire installation is needed, follow the
instructions in the “Hardwire” section.
Note: Access holes should be 2” square
(5.1 cm) with no sharp edges.
• In a hardwire installation, use only copper
supply conductors. The conductors should
have a minimum temperature rating of
194° F (90° C).
Disconnect the electrical power supply and
place a tag at the disconnect switch
indicating that you are working on the
circuit.
WARNING
Be sure electrical power is turned off at
circuit breaker or fuse box before servicing
or installing unit. DO NOT use an
extension cord for this appliance.
Grounding Instructions if Hardwired:
This appliance must be connected to a
grounded metal, permanent wiring system;
or an equipment grounding conductor must
be run with the circuit conductors and
connected to the equipment – grounding
terminal or lead on the appliance.
• For a cord connected undercounter
dishwasher:
1. The power supply receptacle for the
appliance should be installed in a
cabinet or on a wall adjacent to the
under counter space in which the
appliance is to be installed;
2. There should be an opening through
the partition between the
compartments mentioned in Item (1),
that is large enough for the attachment
plug to pass through. The longest
dimension of the opening shall not be
more than 1-1/2” (38 mm).
3. The edges of the opening mentioned in
Item (2) should, if the partition is wood,
be smooth and rounded or, if the
partition is metal, be covered with the
grommet provided for this purpose by
the manufacturer; and
WARNING
Improper connection of the equipment –
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or serviceman if you are in
doubt as to whether the appliance is
properly grounded. DO NOT modify the
plug provided with the appliance; if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
9
Hardwire Conduit Option (cont.)
Hardwire Conduit Option
7
2
1
Green
(Ground)
8
2
1
2
3
2
1
Remove any loose items in the dishwasher and carefully
lay the dishwasher on its back. Note: Be careful not to
pinch hoses or power cord beneath dishwasher.
3
3
x4
1
Remove bottom pan. Note: Rapid removal of the bottom pan will
cause damage to the moisture sensor. For installation and servicing,
slowly pull the bottom pan from the unit and disconnect the wire
from the moisture sensor, which is located in the center of the pan.
Connect ground wire. Tighten screws on strain relief.
Note: Reinstall front plate.
Run wire through grommet on bottom pan.
Replace bottom pan.
4
3
3
1
x2
2
Remove front plate.
Remove factory installed power
cable from terminal block.
5
6
Black
(Line)
1
1
1
2
White
(Neutral)
Attach UL approved 3/4” strain relief (not included) to
bottom of terminal box. Run wires through strain relief.
2
Connect wires to terminal block.
10
4 x4
11
Counter Balance Spring Adjustment
1
Installation
(if necessary)
2
1
2
2
1
1
2
2
1
4
x4
1
2
3
2
Carefully lay dishwasher on its back and attach the kick
plate brackets. Screws for the brackets will already be
in the base. Note: Be careful not to pinch hoses or
power cord beneath dishwasher.
Remove spring from dishwasher.
Disconnect cable from hook.
To adjust the depth of the kick plate, loosen screws on
the bracket and position in the required depth. Tighten
screws and repeat for other side.
Increase
tension
3
4
3
4
1
Decrease
tension
1
1
2
x2
Set counter balance spring connector in appropriate
location.
Reconnect cable to hook.
2
Attach brackets with two screws (1 per bracket).
Using tie strap attached to dishwasher, band water line,
drain line, and power cord together.
5
6
1
Note: For custom panel installation,
the door may require adjustment
to the preload of the counterbalance
springs. Follow these steps to
adjust the tension.
2
Position unit in front of cutout.
12
Slide unit into opening; be sure to feed water, electrical
and discharge lines into adjacent cabinet.
13
Final Installation
Leveling
7a
7b
Equal distance
11
Equal distance
12a
1.0”
(2.5 cm)
DO
WN
Cut here for
5/8” (1.6 cm)
DOW
N
UP
UP
DOWN
UP
1
OW
N
UP
For 301 models, place a level on handle, then adjust to
appropriate height. Left and right adjust side to side
and center adjusts front to back.
For 201 models, remove front panel to access the front
leveling legs. Leveling legs will be raised during
shipping. Adjust front leveling legs down using a 1/4
drive ratchet. When the adjustment nut is visible,
complete the lowering of the legs from the top. When
the legs are down, tighten the locking nut on the top
of the leg. To level center rear leg, see Step 7a.
8
Cut here for
3/4” (1.9 cm)
2
12b
To check level, front to back, pull the top rack half-way out of
unit. The rack should remain stationary and not move in or out.
Note: Leveling is important for optimal performance.
9
(Discharge with food waste disposer)
Note: Be sure to remove the knockout or plug from the
fitting of the disposer before connecting drain line.
Identify discharge connection size; cut line to correct
size and connect. Clamp if necessary.
12c
(Standard discharge)
10
12d
Air Gap
(Discharge with air gap)
13
Air Gap
Minimum
20”
(50.8 cm)
from floor
x2
Install High Loop Clip, which is provided, a minimum of
20” (50.8 cm) from the floor. Refer to the Drain section
of "General Information" for proper installation
requirements.
Attach screws through bracket into cabinets.
14
(Discharge with food waste disposer and air gap)
Connect water line.
15
Final Installation (cont.)
Performance Checklist
14
Testing for Leaks
Unit Reset
A qualified installer should carry out the following
checks:
• If the unit should need to be reset for any
reason, push and hold the “START” button for
4 seconds.
h Remove packaging and parts.
h Turn on the water supply and check for leaks.
h Turn the power on at breaker/fuse box and
Install kick plate.
test the dishwasher operation by running a
rinse and hold cycle. (This should take about
12 minutes.)
h Turn off the electrical power and check for
leaks under the dishwasher.
h Make sure that no kinks have developed in
the drain lines.
Final Preparation
• Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
16
17
Service & Registration
Only authorized replacement parts may be used in performing service on the appliance. Do not
repair or replace any part of the appliance unless specifically recommended in the manual. All
servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts
distributor in your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
The serial number and model number for your dishwasher are located on the identification plate mounted
on the bottom left side of the dishwasher door opening.
Record the following information indicated below. You will need it if service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
These installation instructions should remain with the dishwasher for future
reference.
18
19