Vizio VW46LFHDTV10A User manual

VIZIO VW46L FHDTV10A User Manual
Dear VIZIO Customer,
Congratulations on your new VIZIO VW46L
FHDTV10A High Definition LCD Television
purchase. Thank you for your support. For
maximum benefit of your set, please read these
instructions before making any adjustments, and
retain them for future reference. We hope you will
experience many years of enjoyment from your
new VIZIO VW46L FHDTV10A High Definition
Television.
For assistance, please call (877) 698-4946 or email us at techsupport@vizio.com.
To purchase or inquire about accessories and
installation services for your VIZIO LCD HDTV,
please visit our website at www.VIZIO.com or
call toll free at 888-VIZIOCE (888-849-4623).
We recommend you register your VIZIO VW46L
FHDTV10A
either
at
our
website
www.VIZIO.com or fill in your registration card
and mail it in. For peace of mind and to protect
your investment beyond the standard warranty,
VIZIO offers on-site extended warranty service
plans. These plans give additional coverage
during the standard warranty period. Visit our
website or call us to purchase a plan.
Write down the serial number located on the back
of your VW46L FHDTV10A.
__ __ __ __ __ __ __ __ __ __ __ __ __ __
Purchase Date _____________________
VIZIO is a registered trademark of V, Inc.
HDMI logo and “High Definition Multimedia Interface” are registered trademarks of HDMI Licensing LLC.
Manufactured under license from Dolby Laboratories
Dolby and the double-D symbol are trademarks of Dolby Laboratories
Version 12/7/2007
1
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
THIS PRODUCT HAS BEEN DESIGNED AND TESTED FOR COMPLIANCE WITH REGULATORY SAFETY CERTIFICATIONS
This product is designed and manufactured to operate within defined design limits, and misuse may result in electric
shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation,
use and maintenance of the product. Read the following safety instructions before operating the display. Keep these
instructions in a safe place for future reference.
•
•
•
•
•
•
•
•
•
•
•
To avoid the risk of electric shock or component damage, switch off the power before connecting other components to the VW46L
FHDTV10A.
Unplug the power cord before cleaning the VW46L FHDTV10A. A damp cloth is sufficient for cleaning the VW46L FHDTV10A. Do not
use a liquid or a spray cleaner for cleaning the product. Do not use abrasive cleaners.
Always use the accessories recommended by the manufacturer to insure compatibility.
When moving the VW46L FHDTV10A from an area of low temperature to an area of high temperature, condensation may form on the
housing. Do not turn on the VW46L FHDTV10A immediately after this to avoid causing fire, electric shock or component damage.
Do not place the VW46L FHDTV10A on an unstable cart, stand, or table. If the VW46L FHDTV10A falls, it can injure a person and
cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the VW46L
FHDTV10A.
A distance of at least 3 feet should be maintained between the VW46L FHDTV10A and any heat source, i.e. radiator, heater, oven,
amplifier etc. Do not install the product close to smoke. Operating the product close to smoke or moisture may cause fire or electric
shock.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the VW46L
FHDTV10A and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the VW46L
FHDTV10A in a bookcase or cabinet unless proper ventilation is provided.
Never push any object into the slot on the VW46L FHDTV10A cabinet. Do not place any objects on the top of the product. It could
short circuit parts causing a fire or electric shock. Never spill liquids on the VW46L FHDTV10A.
The VW46L FHDTV10A should be operated only from the type of power source indicated on the label. If you are not sure of the type of
power supplied to your home, consult your dealer or local power company.
The power cable must be replaced when using different voltage from that specified in the User Manual. For more information, contact
your dealer.
The VW46L FHDTV10A is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only
into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install
the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the
grounded plug.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
The wall socket shall be installed near the equipment and shall be easily accessible.
Only the marked power source can be used for the product. Any power source other than the specified one may cause fire or electric
shock.
Do not touch the power cord during lightning. To avoid electric shock, avoid handling the power cord during electrical storms.
Unplug the unit during a lightening storm or when it will not be used for long period of time. This will protect the VW46L FHDTV10A
from damage due to power surges.
Do not attempt to repair or service the product yourself. Opening or removing the back cover may expose you to high voltages, the risk
of electric shock, and other hazards. If repair is required, please contact your dealer and refer all servicing to qualified service
personnel.
Keep the product away from moisture. Do not expose this appliance to rain or moisture. If water penetrates into the product, unplug
the power cord and contact your dealer. Continuous use in this case may result in fire or electric shock.
Do not use the product if any abnormality occurs. If any smoke or odor becomes apparent, unplug the power cord and contact your
dealer immediately. Do not try to repair the product yourself.
Avoid using dropped or damaged appliances. If the product is dropped and the housing is damaged, the internal components may
function abnormally. Unplug the power cord immediately and contact your dealer for repair. Continued use of the product may cause
fire or electric shock.
Do not install the product in an area with heavy dust or high humidity. Operating the product in environments with heavy dust or high
humidity may cause fire or electric shock.
Follow instructions for moving the product. Ensure that the power connector and any other cables are unplugged before moving the
product.
Hold the power connector when removing the power cable. Pulling the power cable itself may damage the wires inside the cable and
cause fire or electric shock. When the product will not be used for an extended period of time, unplug the power connector.
To avoid risk of electric shock, do not touch the connector with wet hands.
Insert batteries in accordance with instructions. Incorrect polarities may cause damage and leakage of the batteries, operator injury
and contamination the remote controller.
If any of the following occurs please contact the dealer:
o
The power connector fails or frays.
o
Liquid sprays or any object drops into the VW46L FHDTV10A.
o
The Display is exposed to rain or other moisture.
o
The Display is dropped or damaged in any way.
o
The performance of the Display changes substantially.
Version 12/7/2007
2
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Television Antenna Connection Protection
External Television Antenna Grounding
If an outside antenna/satellite dish or cable system is to be connected to the TV, make sure that the
antenna or cable system is electrically grounded to provide some protection against voltage surges and
static charges.
Article 810 of the National Electrical Code, ANSI/NFPSA 70, provides information with regard to proper
grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge
unit, size of the grounding conductors, location of antenna discharge unit, connection to grounding
electrodes, and requirements of the grounding electrode.
Lightning Protection
For added protection of the TV during a lightning storm or when it is left unattended or unused for long
periods of time, unplug the TV from the wall outlet and disconnect the antenna or cable system.
Power Lines
Do not locate the antenna near overhead light or power circuits, or where it could fall into such power
lines or circuits.
Version 12/7/2007
3
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Opening the Package
Your VIZIO VW46L FHDTV10A and it accompanying accessories are carefully packed in a cardboard
carton that has been designed to protect it from transportation damage. Now you have opened the carton
check that the VW46L FHDTV10A is in good condition and that all of the accessories are included.
The VW46L FHDTV10A weighs approximately 75lbs and is nearly 45” wide and we advise that you take
sensible lifting precautions when you unpack and install the HDTV.
The screen can easily be scratched or broken so please handle the product gently and never place the
HDTV with the glass facing downwards on a surface without protective padding.
IMPORTANT: Save the carton and packing material for future shipping.
Package Contents
VIZIO VW46L FHDTV10A
VIZIO Remote Control
Power Cord
This User Manual
Quick Setup Guide
Registration Card
VIP Services Brochure
2 (Double A) Batteries for the Remote Control
VIZIO Warranty and Repair Information
Version 12/7/2007
4
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Additional Certified Accessories for the VIZIO
VW46L FHDTV10A are sold separately
Wall Mounts
High Definition Cables
Extra or replacement Remote
VIZIO also offers Installation Services and Extended Warranty Services for your VIZIO VW46L
FHDTV10A
To purchase or inquire about additional accessories and services for your VIZIO product, visit our web
site at www.VIZIO.com or call us toll free at 888-VIZIOCE (888-849-4623)
Installation Preparation
Please read this user manual carefully before installing your VIZIO HDTV.
The power consumption of the TV is about 320W, please use the power cord designated for TV. When
an extension cord is required, use one with the correct power rating. The cord must be grounded and the
grounding feature must not be defeated.
The TV should be installed on a flat surface to avoid tipping. For proper ventilation, you must allow space
between the back of the TV and the wall. If you would like to mount your TV on the wall, please see
below ‘Preparing Your LCD HDTV for Wall Mounting’ for additional information. Avoid installing the TV in
places with high humidity, dust or smoke so as not to shorten the service life of the electronic components.
Install the TV in landscape orientation; any 90˚ clockwise or counter-clockwise installation may induce
poor ventilation and excessive component damage.
VIZIO offers professional installation services. Please contact VIZIO for more information on these
services at 888-VIZIOCE (888-849-4623) or www.VIZIO.com.
Attaching the Safety Strap
For when the VW46L FHDTV10A is not mounted on the wall with a Wall Mount, a Safety Strap has been
included to attach the HDTV to the wall to reduce the chance of the HDTV being pulled over. The Safety
Strap should be used with common sense practice such as ensuring that children (or adults) do not climb
up, grabbing the top of the HDTV and pulling it onto themselves.
1.
Fix one end of the strap to the wall. If you have a drywall
finish it is preferable to fix it to a stud if it is a drywall finish,
using a washer underneath the screw head. If you have a
solid wall you should use a lag bolt, again using a washer
under the nut.
2.
Fix the other end of the Safety
Strap to one of the upper wall
mounting holes on the back of
the HDTV, using a washer
under
the
screw
head.
Version 12/7/2007
5
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Preparing Your LCD HDTV for Wall Mounting
The VIZIO VW46L FHDTV10A can either be kept on the stand base or mounted on the wall for viewing.
If you choose to mount the VW46L FHDTV10A on the wall, please follow the instructions below for
removing the stand base.
To remove the stand base
1. Unplug all of the cables and cords
from your VW46L FHDTV10A.
2. Place the VW46L FHDTV10A face
down on a soft and flat surface
(blanket, foam, cloth, etc) to prevent
any damage to the TV.
3. Remove the eight (8) screws holding
the base to the TV.
4. Carefully remove the stand base.
Note: The specs for these screws are M4,
15mm long, .7 pitch.
5. Now, the VW46L FHDTV10A can fit
securely to a mount (sold separately) by
utilizing the mounting holes in the center of
the back panel of the TV. Please make sure to
read the instructions of your specific mount to
properly hang the VW46L FHDTV10A.
The pitch of the mounting holes is 630mm
horizontally and 200mm vertically.
The screw type required is metric M8,
1.25mm pitch. The length of the screws will
depend on the thickness plate being attach to
the TV set; our brackets come with different
length screws.
To find the perfect mount for the VIZIO
VW46L FHDTV10A, browse VIZIO’s certified
mount selection at www.VIZIO.com or call directly 888-VIZIOCE (888-849-4623).
Version 12/7/2007
6
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Table of Contents
Chapter 1 Basic Controls and Connections .................................................................. 9
1.1 Front Panel..........................................................................................................................................................9
1.2 Right Side Panel Controls ...................................................................................................................................9
1.3 Rear Panel Connections ...................................................................................................................................10
1.4 VIZIO Remote Control.......................................................................................................................................11
1.4.1 Insertion of Batteries in the Remote Control ..............................................................................................12
1.4.2 Remote Control Range ..............................................................................................................................12
1.4.3 VIZIO Remote Control Precautions ...........................................................................................................12
Chapter 2 Connecting Equipment .................................................................................. 13
2.1 Which Video Connection Should I Use?............................................................................................................13
2.2 Connecting Coaxial (RF) ...................................................................................................................................14
2.2.1 Using Your Antenna or Digital Cable for DTV /TV .....................................................................................14
2.2.2 Using the Antenna or Cable through your VCR .........................................................................................14
2.3 Connecting Your HDTV Set-Top Box ................................................................................................................15
2.3.1 Using HDMI ...............................................................................................................................................15
2.3.2 Using Component Video............................................................................................................................17
2.4 Connecting Your Basic Set-Top Box .................................................................................................................18
2.4.1 Using Composite Video .............................................................................................................................18
2.4.2 Using Coax (RF) ........................................................................................................................................18
2.5 Connecting Your DVD Player ............................................................................................................................19
2.5.1 Using HDMI ...............................................................................................................................................19
2.5.2 Using Component Video............................................................................................................................20
2.5.3 Using S-Video (AV)....................................................................................................................................21
2.5.4 Using Composite (AV) Video .....................................................................................................................21
2.6 Connecting Your VCR or Video Camera ..........................................................................................................22
2.7 Connecting an external Receiver/Amp ..............................................................................................................23
2.7.1 Optical Output of Audio received with HD Programs .................................................................................23
2.8 Connecting a PC Computer ..............................................................................................................................24
2.8.1 Preset PC Resolutions...............................................................................................................................25
2.8.2 Resolution (1920x1080) through RGB (15-Pin VGA) Input........................................................................25
Chapter 3 Setting Up to Watch Television...................................................................26
3.1 Basic LCD HDTV Start Up ................................................................................................................................26
3.2 Watching a TV Program ....................................................................................................................................31
3.3 Adjusting Basic HDTV Settings .........................................................................................................................32
3.4 Program Information..........................................................................................................................................33
3.5 Information on HDTV Status .............................................................................................................................33
Chapter 4 Advanced Adjustment of HDTV................................................................... 34
4.1 Using the On Screen Display (OSD) .................................................................................................................34
4.2 DTV / TV Input Picture Adjustment....................................................................................................................35
4.2.1 Picture Mode .............................................................................................................................................35
4.2.2 Backlight ....................................................................................................................................................36
4.2.3 Brightness..................................................................................................................................................36
4.2.4 Contrast .....................................................................................................................................................37
4.2.5 Color ..........................................................................................................................................................37
4.2.6 Tint.............................................................................................................................................................37
4.2.7 Sharpness .................................................................................................................................................38
4.2.8 Color Temperature.....................................................................................................................................38
4.2.9 Advanced Video ........................................................................................................................................39
4.3 DTV / TV Input Audio Adjustment......................................................................................................................41
4.3.1 Volume ......................................................................................................................................................41
4.3.2 Bass...........................................................................................................................................................41
4.3.3 Treble ........................................................................................................................................................42
4.3.4 Balance......................................................................................................................................................42
4.3.5 Surround....................................................................................................................................................42
4.3.6 Digital Audio Out........................................................................................................................................42
4.3.7 Speakers ...................................................................................................................................................43
4.3.8 Lip Sync.....................................................................................................................................................43
4.4 DTV / TV Tuner Setup.......................................................................................................................................44
4.4.1 Tuner Mode ...............................................................................................................................................44
Version 12/7/2007
7
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.4.2 Auto Search...............................................................................................................................................44
4.4.3 Skip Channel .............................................................................................................................................44
4.4.4 MTS ...........................................................................................................................................................45
4.4.5 Time Zone .................................................................................................................................................45
4.4.6 Daylight Saving..........................................................................................................................................45
4.5 DTV / TV Input Setup ........................................................................................................................................46
4.5.1 Language...................................................................................................................................................46
4.5.2 Sleep Timer ...............................................................................................................................................46
4.5.3 Wide ..........................................................................................................................................................46
4.5.4 Input Naming .............................................................................................................................................47
4.5.5 Closed Caption (CC)..................................................................................................................................48
4.5.6 Closed Caption On Mute ...........................................................................................................................48
4.5.7 Digital Closed Caption ...............................................................................................................................49
4.5.8 Reset All Settings ......................................................................................................................................49
4.6 DTV / TV Input Parental Control........................................................................................................................50
4.6.1 Channel Block ...........................................................................................................................................50
4.6.2 TV Rating...................................................................................................................................................51
4.6.3 Movie Rating..............................................................................................................................................52
4.6.4 Check for New DTV Rating........................................................................................................................52
4.6.5 Blocked Unrated Programming..................................................................................................................53
4.6.6 Change the Password ...............................................................................................................................53
4.7 HDMI Input Picture Adjustment .........................................................................................................................54
4.8 HDMI Input Audio Adjustment ...........................................................................................................................54
4.9 HDMI Input Setup..............................................................................................................................................54
4.10 Video Input Picture Adjustment .......................................................................................................................55
4.11 Video Input Audio Adjustment .........................................................................................................................55
4.12 Video Input Setup............................................................................................................................................55
4.13 Video Input Parental Control ...........................................................................................................................56
4.14 PC Input Picture Adjustment ...........................................................................................................................56
4.14.1 Auto Adjust ..............................................................................................................................................56
4.14.2 Backlight ..................................................................................................................................................56
4.14.3 Brightness................................................................................................................................................57
4.14.4 Contrast ...................................................................................................................................................57
4.14.5 Color Temperature...................................................................................................................................58
4.14.6 H-SIZE.....................................................................................................................................................58
4.14.7 H. Position ...............................................................................................................................................59
4.14.8 V. Position ...............................................................................................................................................59
4.14.9 Fine Tune ................................................................................................................................................59
4.15 PC Input Audio Adjustment .............................................................................................................................60
4.16 PC Input Setup ................................................................................................................................................60
4.17 Understanding Viewing Features ....................................................................................................................61
4.17.1 Viewing Modes ........................................................................................................................................61
4.17.2 Using a Cable or Satellite Remote...........................................................................................................62
Chapter 5 Maintenance and Troubleshooting............................................................. 63
5.1 Maintenance......................................................................................................................................................63
5.2 Troubleshooting Guide ......................................................................................................................................64
5.3 Telephone & Technical Support ........................................................................................................................65
5.4 Compliance .......................................................................................................................................................66
5.5 FCC Class B Radio Interference Statement......................................................................................................66
Chapter 6 Miscellaneous Information ........................................................................... 67
6.1 Specifications ....................................................................................................................................................67
6.2 Glossary – Standard Definitions ........................................................................................................................68
6.3 Index .................................................................................................................................................................69
Version 12/7/2007
8
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Chapter 1 Basic Controls and Connections
1.1 Front Panel
Power ‘VIZIO’ light – The VIZIO name lights white when
powered on and orange when powered off.
Remote Control Sensor – This is the window through which all
of the remote control signals pass to the sensor. Point the
remote control directly at this window for the best response to
the remote signal.
1.2 Right Side Panel Controls
POWER (
) – Switch the VW46L FHDTV10A on by pressing the button once. Press the button again
to the VW46L FHDTV10A off.
MENU – This button activates the On Screen Display (OSD). If
a sub-menu is active, pressing this button will return to the
previous menu level.
CHANNEL +/- – Use these buttons to step up or down the TV
channels. While the OSD is active, these buttons function as
up and down controls in the OSD menus.
VOLUME +/- – Use these buttons to increase or decrease to
the speaker volume. While the OSD is active, these buttons
function as left and right controls in the OSD menus.
INPUT (ENTER) – Repeated
pressing of this buttons steps
through the input sources in
the following sequence: TV,
AV/S-Video,
Component1,
Component2, RGB, HDMI1,
HDMI2, and HDMI3. Once
you have stepped through the
entire sequence, you will
return to the beginning.
Version 12/7/2007
9
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
1.3 Rear Panel Connections
1
6
3
2
4
5
7
1.
8
12
10
9
11
SERVICE – This custom communication port is for factory service only. Use of this input for
any purpose other than factory authorized service will void the manufacturer’s
warranty of this equipment.
2.
HDMI 1 – Connect the primary source for digital video such as a DVD multimedia player or
set top box through this all digital connector. The white color band on the rear of the TV
indicates this connection.
3.
HDMI 2 – Connect the secondary source for digital video such as a DVD multimedia player
or set top box through this all digital connector. The white color band on the rear of the TV
indicates this connection.
4.
HDMI 3 – Connect a third source for digital video such as a DVD multimedia player or set top
box through this all digital connector. The white color band on the rear of the TV indicates
this connection. For users who want to connect to a DVI enabled device, use a DVI-HDMI
cable and connect the Analog Audio output of the device to the L+R AUDIO here. . Your
VIZIO Certified HDMI and HDMI-DVI cables are available for purchase from www.VIZIO.com
or by calling 888-VIZIOCE (888-849-4623).
5.
RGB PC – Connect the video and audio from a computer here. The blue color band on the
rear of the TV indicates this connection. A cable with a 1/8” mini plug stereo connector at the
end connecting to the TV is needed if sound is also transmitted with this signal.
6.
COMPONENT 1 (YPb/CbPr/Cr with Audio L/R) – Connect the primary source for
component video devices such as a DVD Player or set top box here. From left to right, use
green for Y, blue for Pb (or Cb), red for Pr (or Cr), white for left audio and red for right audio
inputs. The green color band on the rear of the TV indicates this connection.
7.
COMPONENT 2 (YPb/CbPr/Cr with Audio L/R) – Connect the secondary source for
component video devices such as a DVD Player or set top box here. From left to right, use
green for Y, blue for Pb (or Cb), red for Pr (or Cr), white for left audio and red for right audio
inputs. The purple color band on the rear of the TV indicates this connection.
8.
AV/S-VIDEO IN – Connect a source for composite or S-video image devices, such as a VCR
or video game. Use the white and red connectors to connect the external audio from the
same source, if S-Video is connected; such signal will take priority over the input. The yellow
and red color band on the rear of the TV indicates this connection.
9.
DTV/TV – Connect to an antenna or digital cable (no Cable Box) for Digital TV.*
10.
OPTICAL DIGITAL AUDIO OUT –When a digital audio signal is associated with an input
which is selected for viewing, the digital audio associated with digital programming will be
available on this SPDIF Optical connector for connection to your home theatre system. The
white color band on the rear of the TV indicates this connection.
11.
ANALOG AUDIO OUT – Connect the audio from the LCD HDTV to an external device, such
as a home theatre system, external amplifier or stereo. Speakers cannot be connected
directly to here. The white color band on the rear of the TV indicates this connection.
12.
AC IN – Plug-in the supplied AC Power Cord here.
* For digital TV stations in your area visit www.antennaweb.org.
Version 12/7/2007
10
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
1.4 VIZIO Remote Control
GUIDE – This button displays program information. Press this button once when in TV mode and the
information of the program being viewed is shown. Press it a second time and the Electronic
Programming Guide will appear in the screen. In any other mode when this button is pressed, the screen
will display the selected input plus the definition of the signal; i.e. HDMI 720p, HDMI 1080i, etc.
POWER – Press this button to turn the TV on from the Standby mode. Press it again to return to the
Standby mode.
HDMI – Press this button to select the HDMI input. By pressing it
repeatedly you will go through the three (HDMI 1, HDMI 2 and HDMI 3)
inputs in sequence.
MUTE – This button turns the sound on and off.
TV – Press this button to select TV.
COMPONENT – Press this button to select the Component (YPbPr)
input. By pressing this button repeatedly you will be switching from
Component 1 to Component 2 and vice versa.
LAST – This button recalls the previously viewed channel. If the OnScreen Display (OSD) menu is being used, this button will allow you to
get back to previous menu screen or out to your program when you
press it repeatedly.
AV – Press this button to select AV (either Composite or S-Video) input.
MENU – Use this button for the On-Screen Display (OSD) menu. When
it is used within a menu selection, pressing this key will help you to
make the selection of the feature to be adjusted after it has been
highlighted.
-These labeled buttons are used to navigate the OSD
menu. When navigating the OSD menu, the arrows control the direction
up and down or left and right. They will also be used as value settings
when the slide bar is shown on the screen and option settings to turn a
feature off or on.
hen
NUMBER BUTTON PAD – Use these
buttons to select a channel or enter a
password.
INPUT – This button allows the user to cycle
through the inputs. Repeatedly pressing of
this button will step you through the input
sources in the following sequence: TV,
AV/S-VIDEO, Component1, Component2,
RGB, HDMI1, HDMI2, and HDMI3. Once
you have stepped through the entire
sequence, you will return to the beginning.
- (DASH) – When selecting a digital channel
directly use this button for the separation of
main and sub-channels.
For example,
channel 28-2 would be selected by the
button sequence 2 8 ENTER 2.
Version 12/7/2007
11
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
1.4.1 Insertion of Batteries in the Remote Control
Insert two AA batteries into the remote control. Make sure that you match the (+) and (-) symbols on the
batteries with the (+) and (-) symbols inside the battery compartment. Re-attach the battery cover.
Precautionary Tips for Inserting the Batteries:
Only use the specified AA batteries.
Do not mix new and old batteries. This may result in cracking or leakage
that may pose a fire risk or lead to personal injury.
Inserting the batteries incorrectly may also result in cracking or leakage
that may pose a fire risk or lead to personal injury.
Dispose of the batteries in accordance with local laws and regulations.
Keep the batteries away from children and pets.
1.4.2 Remote Control Range
Point the remote control at the remote control sensor to transmit the commands.
Do not place any obstacles between the remote control and the receiver window.
The effective range of the remote control is approximately 30 feet (10 meters) from the front of the
receiver window, 30° to the left and right, 20° up and down.
1.4.3 VIZIO Remote Control Precautions
The remote control should be kept dry and away from heat sources. Avoid humidity.
If the TV responds erratically to the remote control or does not respond at all, check the batteries. If the
batteries are low or exhausted, replace them with fresh batteries.
When not using the remote control for a long period of time, remove the batteries.
Do not take the batteries apart, heat them, or throw them into a fire.
Do not subject the remote control to undue physical stress, such as striking or dropping it.
Do not attempt to clean the remote control with a volatile solvent. Wipe it with a clean, damp cloth.
Version 12/7/2007
12
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Chapter 2 Connecting Equipment
2.1 Which Video Connection Should I Use?
The VIZIO VW46L FHDTV10A has six different ways to connect your video equipment from a basic
connection to the most advanced for digital displays.
Rear
Panel
Color
Codes
Description
White
HDMI (High-Definition Multimedia Interface) - It is the
first and only industry-supported, uncompressed, alldigital audio/video interface. HDMI provides an
interface between any audio/video source, such as a
set-top box, DVD player, or A/V receiver and an
audio and/or video monitor, such as a digital
television (DTV), over a single cable.
Black
DTV Coaxial RF. When used for MPEG2 encoded
bit streams from ATSC broadcast programming, this
input takes advantage of the High Definition content.
-------------------------------------TV Coaxial RF. This is the connection for standard
NTSC TV using antenna or cable.
Best
(analog)
Blue
RGB PC (VGA) – This video input has separate red,
green and blue color components. The signal carries
horizontal and vertical sync information on the green
signal. This is most commonly used for PC input.
Better
(analog)
Green
and
Purple
Component - The video signal is separated into three
signals, one containing the black-and-white
information and the other two containing the color
information. This enhancement over S-Video takes
advantage of the superior picture provided by
progressive scan DVD players and HDTV formats.
Yellow
and
Red
AV/S-Video – 1. Composite: The complete video
signal is carried through this single (yellow) pin
connector. This is the most commonly used video
connection. 2. S-Video: The video signal is separated
into two signals, one containing the black-and-white
information and the other containing the color
information. Separating the color in this way avoids
‘cross color’ effects where closely spaced black and
white lines are erroneously displayed in color. It also
enables text to be displayed more sharply.
Connection
Quality
(type)
Best
(digital)
Best
(digital)
-----------Good
(analog)
Good
(analog)
Connector
Note: For more info refer to the Quick Start Guide
Version 12/7/2007
13
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.2 Connecting Coaxial (RF)
2.2.1 Using Your Antenna or Digital Cable for DTV
/TV
1.
2.
3.
4.
Turn off the power to the HDTV.
Connect the coaxial (RF) connector from your
antenna or digital cable (out-of-the-wall, not from
the Cable Box) to the DTV/TV CABLE/ANTENNA
connector.
Turn on the power to the HDTV.
Select DTV using the INPUT button on the
remote or side of the HDTV, or directly by
pressing the TV button on the Remote Control.
Note:
a)
Not all digital TV broadcasts are High Definition (HD). Refer to the
program guides, or consult your cable, satellite or TV station operator.
Digital broadcasts are not available in all areas.
Refer to
www.antennaweb.org for detailed information.
Make sure the antenna and coaxial cable are correctly grounded.
For Professional antenna installation contact us at www.VIZIO.com or
call 1-888-VIZIOCE (1-888-849-4623).
b)
c)
d)
2.2.2 Using the Antenna or Cable through your
VCR
1.
2.
3.
4.
Turn off the power to the HDTV and VCR.
Connect the “Output to TV”, “RF Out” or “Antenna
Out” connector on the rear of your VCR to the
DTV/TV CABLE/ANTENNA connector at the rear
of the HDTV.
Turn on the power to the HDTV and VCR.
Select TV using the INPUT button on the remote
or side of the HDTV, or directly by pressing the
TV button on the Remote Control.
Note: If you have an off-air antenna or cable TV, connect
it to the “Antenna In” connector on the rear of your VCR.
Version 12/7/2007
14
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.3 Connecting Your HDTV Set-Top Box
2.3.1 Using HDMI
HDTV Set-Top Boxes that have a HDMI digital interface should be connected to the HDMI input of the
LCD HDTV for optimal results.
Note: To maintain the display quality, use a VIZIO certified HDMI cable that is 10 meters.
See www.VIZIO.com or call 1-888-VIZIOCE (1-888-849-4623) for details.
Connecting your HDTV Set-Top Box (Best):
1.
2.
3.
4.
5.
Turn off the power to the HDTV and HDTV Set-Top Box.
Connect a HDMI cable to the HDMI output of your HDTV Set-Top Box and the other end to
the HDMI Input (white color area) at the rear of the HDTV.
Turn on the power to the HDTV and HDTV Set-Top Box.
Select HDMI using the INPUT button on the remote or side of the HDTV, or directly by
pressing the HDMI button on the Remote Control.
If HDMI 1 is been used, you can use either HDMI 2 or HDMI 3; follow the above steps (1
through 3) and then select the desired input number in step 4.
Note:
a)
b)
Version 12/7/2007
The HDMI input on the HDTV supports High-bandwidth Digital Content Protection
(HDCP). HDCP encrypts the transmission between the video source and the
digital display for added security and protection.
Refer to your HDTV Set-Top Box user manual for more information about the
video output requirements of the product or consult your cable or satellite operator.
15
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
For HDTV Set-Top Boxes with DVI:
1.
2.
3.
4.
5.
Turn off the power to the HDTV and HDTV Set-Top Box.
Using a HDMI-DVI cable, connect the DVI end to your HDTV Set-Top Box and the HDMI end
to the HDMI Input (white color area) at the rear of the HDTV.
Using an audio cable (white and red connectors), connect the cable to the audio output
connectors associated with the DVI output on your HDTV Set-Top Box and connect the other
end to the audio connectors associated with the HDMI input (white area) at the rear of the
HDTV.
Turn on the power to the HDTV and HDTV Set-Top Box.
Select HDMI using the INPUT button on the remote or side of the HDTV, or directly by
pressing the HDMI button on the Remote Control.
Note:
a)
b)
c)
Version 12/7/2007
The HDMI input on the HDTV supports High-bandwidth Digital Content Protection
(HDCP). HDCP encrypts the transmission between the video source and the
digital display for added security and protection.
Refer to your HDTV Set-Top Box user manual for more information about the
video output requirements of the product or consult your cable or satellite
operator.
All three HDMI inputs can be used with the audio (right and left) inputs as long as
the input (HDMI) number matches the connection.
16
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.3.2 Using Component Video
Connecting your HDTV Set-Top Box (Better):
1.
2.
3.
4.
5.
6.
7.
Turn off the power to the HDTV and HDTV Set-Top Box.
Connect the Y (green color) connector on your HDTV Set-Top Box to the corresponding Y
(green color) connector in the Component 1 group (green color area - row of connectors
nearest to you when viewing from the rear of the TV) at the rear of the HDTV.
Connect the Pb (blue color) connector on your HDTV Set-Top Box to the corresponding Pb
(blue color) connector in the Component 1 group (green color area - row of connectors
nearest to you when viewing from the rear of the TV) at the rear of the HDTV.
Connect the Pr (red color) connector on your HDTV Set-Top Box to the corresponding Pr (red
color) connector in the Component 1 group (green color area - row of connectors nearest to
you when viewing from the rear of the TV) at the rear of the HDTV.
Using an audio cable (white and red connectors), connect the cable to the audio output
connectors associated with the Component output on your HDTV Set-Top Box and connect
the other end to the audio connectors associated with the Component 1 input (green color
area) at the rear of the HDTV.
Turn on the power to the HDTV and HDTV Set-Top Box.
Select Component 1 using the INPUT button on the remote or side of the HDTV, or directly
by pressing the Component button on the Remote Control.
Note:
Refer to your HDTV Set-Top Box user manual for more information about the
video output requirements of the product or consult your cable or satellite operator.
Version 12/7/2007
17
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.4 Connecting Your Basic Set-Top Box
2.4.1 Using Composite Video
1.
2.
3.
4.
5.
Turn off the power to the HDTV and Set-Top
Box.
Using the AV Cable, connect the Video
(yellow color) connector on your Set-Top Box
to the corresponding Video (yellow color)
connector in the AV/S-Video group
(yellow/red color area) at the rear of the
HDTV.
Using the white and red connectors, connect the cable to the audio output connectors
associated with the Video output on your Set-Top Box and connect the other end to the audio
connectors associated with the AV/S-Video input (yellow/red color area) at the rear of the
HDTV.
Turn on the power to the HDTV and Set-Top Box.
Select AV using the INPUT button on the remote or side of the HDTV, or directly by pressing
the AV button on the Remote Control.
2.4.2 Using Coax (RF)
1.
2.
3.
4.
5.
Turn off the power to the HDTV and Set-Top Box.
Using a Coax (RF) cable, connect one end to the TV
OUT (RF) on your Set Top Box and the other end to the DTV/TV input at the rear of the
HDTV.
Turn on the power to the HDTV and Set-Top Box.
Select TV using the INPUT button on the remote or side of the HDTV, or directly by pressing
the TV button on the Remote Control.
The most common channels; in which the TV must be at, are either channel3 or channel 4.
Please contact your signal provider to verify what channel the TV must be at.
Note: Refer to your Set Top Box user manual for more information
about selecting the video or RF output of the product.
Version 12/7/2007
18
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.5 Connecting Your DVD Player
You have several options for connecting your DVD player to your VW46L FHDTV10A; HDMI, Component,
AV (S-Video or Composite) inputs. Based on your configuration, you can decide which option is right for
you.
2.5.1 Using HDMI
DVD players that have a digital interface such as HDMI (High Definition Multimedia Interface) should be
connected to the HDMI input of the VIZIO VW46L FHDTV10A for optimal results.
Note: To maintain the display quality, use a VIZIO certified HDMI cable available up to 10 meters.
See www.VIZIO.com or call 1-888-VIZIOCE (1-888-849-4623) for details.
Connecting your DVD Player (Best):
1.
2.
3.
4.
Turn off the power to the HDTV and DVD player.
Connect a HDMI cable to the HDMI output of your DVD player and the
other end to the HDMI Input (white color area) at the rear of the HDTV.
Turn on the power to the HDTV and DVD player.
Select HDMI using the INPUT button on the remote or side of the HDTV,
or directly by pressing the HDMI button on the Remote Control.
5.
If HDMI 1 input is already being used, please select either HDMI
2 or HDMI3 and follow Steps 1through 4.
For DVD Players with DVI:
Note: Refer to
your
DVD
player
user
manual
for
moreinformatio
n about the
video
output
requirements of
the product.
5.
1.
2.
3.
Turn off the HDTV and DVD player.
Using a HDMI-DVI cable, connect the DVI end to your
DVD player and the HDMI end to the HDMI Input
(white color area) at the rear of the HDTV.
Connect an audio cable (white and red connectors) to
the audio output connectors associated with the DVI
output of the DVD player and connect the other end
to the audio connectors by the HDMI input (white
area) at the rear of the HDTV.
4.
Turn on the power to the HDTV and your DVD
player.
Select HDMI using the INPUT button on the remote or side of the HDTV, or directly by
pressing the HDMI button on the Remote.
Version 12/7/2007
19
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.5.2 Using Component Video
Connecting your DVD Player (Better):
1.
2.
3.
4.
5.
6.
7.
8.
Turn off the power to the HDTV and DVD player.
Connect the Y (green color) connector on your DVD player to the corresponding Y (green
color) connector in the Component 1 group (green color area - row of connectors nearest to
you when viewing from the rear of the TV) at the rear of the HDTV.
Connect the Pb (blue color) connector on your DVD player to the corresponding Pb (blue
color) connector in the Component 1 group (green color area - row of connectors nearest to
you when viewing from the rear of the TV) at the rear of the HDTV.
Connect the Pr (red color) connector on your DVD player to the corresponding Pr (red color)
connector in the Component 1 group (green color area - row of connectors nearest to you
when viewing from the rear of the TV) at the rear of the HDTV.
Using an audio cable (white and red connectors), connect the cable to the audio output
connectors associated with the Component output on your DVD player and connect the other
end to the audio connectors associated with the Component 1 input (green color area) at the
rear of the HDTV.
Turn on the power to the HDTV and DVD player.
Select Component using the INPUT button on the remote or side of the HDTV, or directly by
pressing the Component button on the Remote Control.
If Component 1 is already being used or you decide to use Component 2; please make the
cable connections and follow the steps 1 through 7 to have the DVD player playing through
your TV.
Note: Refer to your DVD player user manual for more
information about the video output requirements of the product.
Version 12/7/2007
20
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.5.3 Using S-Video (AV)
Connecting your DVD Player (Good):
1.
2.
3.
4.
5.
Turn off the power to the HDTV and DVD
player.
Connect the S-Video jack on the rear of your
DVD player to the S-Video jack in the AV/SVideo group on the side of the HDTV.
Connect an audio cable (white and red connectors) to the audio output connectors
associated with the S-Video output on your DVD player and connect the other end to the
audio connectors associated with the AV/S-Video input on the rear of the HDTV.
Turn on the power to the HDTV and DVD player.
Select AV using the INPUT button on the remote or side of the HDTV, or directly by pressing
the AV button on the Remote Control.
2.5.4 Using Composite (AV) Video
Connecting your DVD Player (Good):
1.
2.
3.
4.
5.
Turn off the power to the HDTV and DVD
player.
Connect the Video (yellow/red color area)
connector on your DVD player to the Video
(yellow color) connector in the AV/S-Video
group (yellow/red color area).
Connect the R (red color) and L (white
color) audio connectors on your DVD
player to the corresponding R (red color)
and L (white color) audio input connectors
in the AV/S-Video group (yellow/red color area).
Turn on the power to the HDTV and DVD Player.
Select AV using the INPUT button on the remote or side of the HDTV, or directly by pressing
the AV button on the Remote Control.
Note:
a)
Version 12/7/2007
Refer to your DVD player user manual for more information
about the video output requirements of the product.
21
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.6 Connecting Your VCR or Video Camera
1.
2.
3.
4.
5.
Turn off the HDTV and VCR or Video
Camera.
Connect the S-Video jack on the rear of your
VCR or Video Camera to the S-Video jack in
the AV/S-Video group on the rear side of the
HDTV.
Connect an audio cable (white and red connectors) cable to the audio output connectors
associated with the S-Video output on your VCR or Video Camera and connect the other end
to the audio connectors associated with the AV input on the side of the HDTV.
Turn on the power to the HDTV and VCR or Video Camera.
Select AV using the INPUT button on the remote or side of the HDTV, or directly by pressing
the AV button on the Remote Control.
Note: Refer to your VCR or Video Camera user manual for more
information about the video output requirements of the product.
Version 12/7/2007
22
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.7 Connecting an external Receiver/Amp
1.
2.
Turn off the power to the LCD HDTV and Receiver/Amp.
Using an audio cable (white and red connectors), connect the cable to the audio input
connectors on the Receiver/Amp and connect the other end to the ANALOG OUT (white
area) audio connectors at the rear of the LCD HDTV.
3.
Turn on the power to the LCD HDTV
and Receiver/Amp.
4.
Then press the MENU button on the
remote control to open the On-Screen
Display (OSD) menu.
5.
Press the
on the remote control to
select the Audio menu.
6.
Press the
on the remote control
to select SPEAKERS.
7.
Press the
on the remote control to
select OFF so that the sound from the
LCD HDTV will now be routed
through your Receiver/Amp system.
Press the LAST key once to return to the previous screen or repeatedly to return to your program if task
has been completed.
Note:
a)
b)
Refer to your Receiver/Amp user manual to select the corresponding audio input.
The audio output is not amplified and cannot be connected directly to external speakers.
2.7.1 Optical
Programs
Output
of
Audio
received
with
HD
If your sound system has a SPDIF (optical) digital audio input you can connect it to the optical DIGITAL
AUDIO OUT (white area) at the rear of the LCD HDTV. This is active when receiving digital audio with
the program being viewed no matter what input (TV, AV, Component or HDMI) is being used.
Version 12/7/2007
23
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.8 Connecting a PC Computer
1.
2.
3.
4.
5.
Note:
a)
b)
Turn off the power to the HDTV and PC
Computer.
Connect a 15-pin D-Sub RGB (VGA) cable to the
RGB output of your pc computer and the other
end to the RGB PC input (blue area) at the rear of
the HDTV.
Connect the Audio Out on your pc computer to
the RGB PC Audio input (blue area) at the rear of
the HDTV. This connection must have a 1/8’
stereo mini plug at one end of the cable to fit into
the computer’s input jack.
Turn on the HDTV and PC Computer.
Select RGB using the INPUT button on the remote or side of the HDTV.
For the best picture quality when connecting a pc computer through RGB PC, please refer
to the pc or graphic card’s user guide to find out if it is capable of an output of 1920x1080
at 60Hzwhen using the parameters and values given to you on Section 2.8.2 of this User’s
Manual by way of VESA Reduce Blanking timing.
A RGB (VGA) cable and stereo mini jack cable are not included and can be purchased at
an electronics store.
Version 12/7/2007
24
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
2.8.1 Preset PC Resolutions
If connecting to a PC through the RGB PC input, set the TV timing mode to VESA 1920x1080 at
60Hz for best picture quality (refer to the graphic card’s user guide for questions on how to set this
timing mode). Please see the table below for the factory preset resolutions.
Resolution
Refresh (Hz)
H.Freq (kHz)
V.Freq (Hz)
H.Sync
V.Sync
Pixel Freq (MHz)
640x480
60
31.5
59.94
N
N
25.175
640x480
75
37.5
75.00
N
N
31.500
720x400
70
31.46
70.08
N
P
28.320
800x600
60
37.9
60.317
P
P
40.000
800x600
72
48.077
72.188
P
P
50.000
800x600
75
46.9
75
P
P
49.500
1024x768
60
48.4
60.01
N
N
65.000
1024x768
70
56.476
70.069
N
N
75.000
1024x768
75
60.0
75.03
P
P
78.750
1360x768
60
47.7
60.00
P
N
85.500
1920x1080
60
66.5
60.00
P
P
136.5
NOTES: N = Negative, P = Positive.
2.8.2 Resolution (1920x1080) through RGB (15-Pin
VGA) Input
If your PC supports VESA Reduce Blanking timing via the VGA card drive program (usually offered by the
VGA Card Manufacturer), your TV set is equipped to have the 1920X1080 resolution display through this
connection using the following timing 136.5MHz. The following parameters are often the values required
by the software or programs to set up the display:
Parameters
Address
Vertical Values
(Lines)
1920
1080
Front Porch
32
1
Sync Width
32
3
Back Porch
64
27
2048
1111
Total
Frequency
Sync Polarity
Version 12/7/2007
Horizontal Values
(Pixels)
66.5 kHz
P
Pixel Rate (MHz)
136.5
Refresh Rate (Hz)
60
25
www.VIZIO.com
60 Hz
P
VIZIO VW46L FHDTV10A User Manual
Chapter 3 Setting Up to Watch Television
For ‘Preparing Your LCD HDTV for Wall Mounting’, see page 6.
3.1 Basic LCD HDTV Start Up
1. Connecting the Power Cable
Connect the power cord to the power cord connector on the back of the HDTV, and then plug the
power cord into an AC wall socket.
2. Connect Audio and Video Cables to the HDTV
(see pages 13 ~ 24 for detailed steps)
3. Turning Power On
Once all the components are connected, press the Power ON button on the side of the HDTV, or
press the Power ON (Red) button on the remote control.
4. Initial Setup
After powering on the TV set, the Initial
Setup screen will come up; please press
the
button on the remote control.
a. The Language choice screen will
be displayed; the default English
option is highlighted. If you wish
to change the OSD language to
Español or Français, press the
button on the remote control to
select the language you want.
Press the MENU button on the
remote to go to the next screen.
Note: At this point, if a Set-Top Box from your Local Cable or Satellite Service Company or other
equipment is been used; please press the LAST key on the remote control and skip to Step 5. If this is
not your case, please continue at Step b.
Version 12/7/2007
26
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
b. The Tuner screen will be
displayed; default choice is
Antenna. If you are using Cable
(No Box) Service, press the
button on the remote control to
highlight CABLE.
Press the
button on the
remote to go to the next screen.
c.
The Channel Scan screen will be
displayed; default choice is Scan.
Press the
button on the
remote control to commence the
search for available channels to
be stored into memory.
If you do not want to scan for
channels at this time, press the
button on the remote to highlight
Skip Scan and then press the
button.
Note: If you select Skip Scan, next time that you decide to complete this procedure; you will need to
select the TV as input (through the Input key) and then go through the Menu option to select the Tuner
setup to get the option of scanning the channels again.
Version 12/7/2007
27
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
d. The screen will now change to
show the progress of the search
for Analog (NTSC) and Digital
(ATSC) channels.
Note: DTV digital broadcast is not available in all areas. Refer to www.antennaweb.org to get information
about availability in your area, type of antenna and in which direction to point your antenna. The channel
availability through cable depends upon which channels your cable operator supplies in Clear QAM;
consult your cable operator for more information.
e. When finished, the Complete
screen will be displayed to inform
you that the HDTV has completed
the Initial Setup.
Press the
button on the
remote control to exit and begin
watching TV.
5. Select Input Source
Select the Input Source for the HDTV by pressing the
INPUT button on the side of the TV or using the Input button on
the remote control. Pressing this button will cycle you through
the following options: TV, AV/S-VIDEO, Component1,
Component2, RGB, HDMI1, HDMI2 and HDMI3.
Now follow the procedure below to display channels from a
different signal (External TV Tuner, VCR, Cable Box or Satellite
Receiver) source, using different inputs at the back of you TV
set.
Version 12/7/2007
28
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
a. Select the correct input connection; RF (DTV/TV) connector, Composite (Yellow, Red
and White) connectors, Component (Red, Green, Blue plus Red and White) connectors, HDMI
connectors or Separate-Video (S-Video) plus Red and White connectors (if applicable). Make the
physical connection or hook up.
b. If you have an HD service you must use the HDMI (best) or Component connection.
Note: Composite (AV) and S-Video Cables can only be used for SD (480i) pictures.
c. Turn on your Cable Box, VCR, External TV Tuner or Satellite Receiver and you will see
a picture on your TV set. If there is no picture, make sure you have selected the correct input on the TV
set.
d. If the selected input is RF, you should be aware that the TV set needs to be on either
channel 3 or channel 4, matching the channel which has been selected on the back of
the VCR, Cable Box, External TV Tuner or Satellite Receiver. Please refer to Owner’s or
User’s Manual of the equipment for details.
Note: The TV set will be displaying any television station or program selected by the Cable Box, VCR,
External Tuner or Satellite Receiver. The TV set will not be able to change programs or channels; this is
controlled by the equipment sending the signal. If the service being used is the one which setup
includes a box with two different outputs for two different (distant) rooms, then scanning
channels would help you to find the signal. Be aware that the channel to be selected varies from
provider to provider; meaning that, you may have to call your provider company so they could
provide you the specific channel when using high definition made TV sets. Some examples of
these channels are: 105, 106, 115 and 116.
6. Fine Tuning your TV set for Home Use.
After completing Procedure 4 or
Procedure 5; please follow the steps
below to optimize your TV set display:
a. Press the MENU key to bring up
the Menu display. Use the
or
button to scroll to the Color Temperature
option.
b. Press the
button to select it.
c. Press either
or
button to change setting to
Normal, and then press the LAST key again to go
back to previous screen.
Version 12/7/2007
29
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
d. Press either
or
button to
select the Picture Mode option.
e. Press either
or
button to change the
Picture Mode option to Standard.
f. Press the LAST key to exit the on screen
display Menu.
Note: If Procedure 4 had been done, you would like to do the following to ensure that the correct
program times are shown when pressing the Guide key:
Press the MENU key; this will bring up the picture
mode menu.
Pressing either
or
button scroll across to the
icon showing the little satellite dish or antenna. The
next screen will appear showing Time Zone.
Press either
or
button to select it,
Press either
or
button to choose the proper Time
Zone of your area.
Press LAST key repeatedly to exit On-Screen Display
menu.
Your new TV set is now ready to automatically
reproduce the best picture quality out of the input signal which is been fed into it. Enjoy your TV
watching!!
Version 12/7/2007
30
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
3.2 Watching a TV Program
Before you start watching TV, please make sure that any cable, satellite or off-air antenna connections
are secure. Also, verify that the power cord is plugged into a correctly grounded electrical outlet or surge
protector.
1.
2.
Press the power button on the remote or on the side of the HDTV. The VIZIO logo on the
front will change from orange to white.
There are 3 options for selecting your programming:
a. If you are using an antenna or cable connected through the DTV/TV CABLE/ANTENNA
input, you can select TV directly by pressing the TV button on the remote, or by pressing
the INPUT button on the remote or on the side of the HDTV.
b. If you are watching broadcasts through a cable or satellite set-top box connected by an
HDMI cable, select HDMI directly by pressing the HDMI button on the remote, or by
pressing the INPUT button on the remote or on the side of the HDTV.
c. If you are watching broadcasts through a cable or satellite set-top box connected by a
Component (YPbPr) cable, select Component directly by pressing the Component button
on the remote, or by pressing the INPUT button on the remote or on the side of the HDTV.
Note: You should be able to see a picture. If you do not,
make sure that all of the HDTV connections are secure and
you have selected the correct video input source.
3.
When using option 2a, press the Channel buttons on the remote or the CH+ / CH- buttons on
the side of the HDTV to change the channel. Note: The Channel buttons, on the side of the
HDTV and on the remote, control will not work if you are watching a program using HDMI,
Component and AV inputs.
Version 12/7/2007
31
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
3.3 Adjusting Basic HDTV Settings
Volume
To increase the volume, press and hold the VOL+ or
VOL- button on the side of the LCD HDTV or remote
control until the desired level is reached.
TV Channels
To step up or down through the available TV
channels, press the CH+ or CH- button on the side
of the HDTV or remote control once for the next or
previous channel, or hold it depressed until the
desired channel is reached. Note: Channel up and
down will only operate in DTV and TV modes.
Wide
Using this feature, you can watch video content in
different size modes on the HDTV. Press the MENU button on the
remote control to bring up the OSD screen.
Press either the
or
button to select Setup (wrench look alike
icon) options.
Press the
button scroll down to Wide and select it.
Press either the
or
button to select among the modes.
Fore more information see Section 4.17.1 – Viewing Modes, on page 61.
Version 12/7/2007
32
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
3.4 Program Information
Press the GUIDE button on the remote and program information for the channel you are watching will be
displayed on the screen with the live program content in a small window in the lower left corner.
Press the GUIDE button twice and the followings screen will appear showing you the Electronic
Programming Guide.
Press the
or
button to scroll up or down the channels. Each time you pause at a channel, the
program list will update with the program schedule for the channel and the window will show the live
program for that channel. Press the GUIDE button to exit this feature or wait for it to disappear
automatically.
3.5 Information on HDTV Status
When you change TV channels or inputs, an Information Banner is displayed for a few seconds to tell you
the status of the LCD HDTV.
Program Information:
Provided by Broadcaster
Program
Rating
Closed Caption
is available
Version 12/7/2007
Audio is Stereo
TV Channel
Number
Station Name: provided
by Broadcaster
NTSC SDTV (Standard Definition TV)
33
www.VIZIO.com
Source
is Cable
VIZIO VW46L FHDTV10A User Manual
Chapter 4 Advanced Adjustment of HDTV
4.1 Using the On Screen Display (OSD)
The remote control or the control buttons on the right hand side of the TV can control all the function
settings. The On Screen Display (OSD) allows you to adjust the save contrast, brightness and other
settings. The TV will save changes made to the settings, even if the TV is turned off.
The OSD consists of several menu options: Picture Adjust, Audio Adjust, Setup, TV Tuner Setup and
Parental Controls. The main menu options may very depending on your selected input source.
Note: Some of the main menu options may have
additional submenus, i.e. the TV Rating submenu
for Parental Controls.
1.
2.
Press the MENU button on the remote
control or the side of the TV and the
Picture Adjust menu will be shown on
the screen.
Press the
or
button on the
remote control or the VOL + or VOL –
button on the side of the HDTV to
select one of the other menu options.
Picture Adjust
3.
Audio Adjust
TV Tuner Setup
Setup
Parental Controls
Once the menu option is displayed, press the
or
button on the remote control or the
CH + or CH – button on the side of the TV to select one of the items to adjust.
4.
Press the
button on the remote control or the VOL – button on the side of the HDTV to
begin adjustment of the item.
5.
Press MENU when finished.
6.
Repeat steps 2 through 5 to adjust additional options within this menu.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
34
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.2 DTV / TV Input Picture Adjustment
4.2.1 Picture Mode
When the MENU button is pressed, the On Screen
Display (OSD) appears on the PICTURE
adjustment page.
Press the
button to highlight the Picture Mode
selection.
Use the
or
button to choose from Custom,
Standard, Movie and Game.
If Standard, Movie or Game is chosen for the
Picture Mode, still the Picture adjustments are
available for you to set or adjust them to your
preferred settings.
Version 12/7/2007
35
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.2.2 Backlight
Press the
selection.
button to highlight the Backlight
Press the
button to start adjusting the
brightness of the Backlight and the menu page will
disappear and be replaced by a small Backlight Indicator Bar so you can see the light level between the
minimum and maximum available levels.
Use the
or
button to adjust the level.
The Backlight level does not affect the Brightness (black level) or Contrast (white level) of the picture, it
adjusts the lamp current and this affects the overall brilliance of the picture.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.2.3 Brightness
Press the
button to highlight the Brightness selection.
Press the
button to start adjusting the brightness and the menu page will disappear and be replaced
by a small Brightness Indicator Bar so you can see the brightness level between the minimum and
maximum available levels.
Use the
or
button to adjust the level.
The Brightness adjusts the black levels in the picture. If the brightness is too low you will not be able to
see the detail in darker parts of the picture and if the brightness is too high the picture will look washed
out.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
36
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.2.4 Contrast
Press the
button to highlight the Contrast selection.
Press the
button to start adjusting the contrast and the menu page will disappear and be replaced by
a small Contrast Indicator Bar so you can see the contrast level between the minimum and maximum
available levels.
Use the
or
button to adjust the level.
The Contrast adjusts the white levels in the picture. If the contrast is too low the picture will look washed
out and if the contrast is too high you will not be able to see any detail in the bright parts of a picture.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.2.5 Color
Press the
button to highlight the Color selection.
Press the
button to start adjusting the color and the menu page will disappear and be replaced by a
small Color Indicator Bar so you can see the color level between the minimum and maximum available
levels.
Use the
or
button to adjust the level.
The Color adjusts the amount of color in the picture.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.2.6 Tint
Press the
button to highlight the Tint
selection.
Press the
button to start adjusting the tint and
the menu page will disappear and be replaced by
a small Tint Indicator Bar so you can see the tint
adjustment to the left or right of the nominal
position.
Use the
or
button to adjust the level.
The Tint adjusts the hue of the picture. The easiest way to set tint is to look at flesh tones and adjust for
a realistic appearance. In most cases, the default middle position is correct. If people’s faces look too
orange try reducing the level of color first as the case of this is often too much color.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
37
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.2.7 Sharpness
Press the
button to highlight the Sharpness selection.
Press the
button to start adjusting the sharpness and the menu page will disappear and be replaced
by a small Sharpness Indicator Bar so you can see the sharpness level between the minimum and
maximum available levels.
Use the
or
button to adjust the level.
The Sharpness adjusts the sharpness of the picture.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.2.8 Color Temperature
Press the
button to highlight the option for
Color Temperature selection.
The default is COOL; this is the 9300K setting.
Press the
or
button if you want to choose
the Warm, Normal or Custom option.
If you choose the Custom option, then a new menu will be displayed showing the primary color items,
Red, Green and Blue.
Press the
button to highlight the color you wish to adjust.
Press the
button to start adjusting the color
and the menu page will disappear and be replaced
by a small Color (Red, Green or Blue) Indicator
Bar as before.
Use the
or
button to adjust the color.
Press the LAST button when finished. Repeat the
procedure to adjust the other colors if desired.
Version 12/7/2007
38
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.2.9 Advanced Video
Press the
button to highlight the option for Advanced Video selection.
Press either the
or
button to select it. A
new menu will be displayed showing the advanced
functions available for fine tuning of the picture.
DNR
Press the
button to highlight DNR (Dynamic
Noise Reduction). Use this feature to diminish
picture artifacts caused by the digitizing of image
motion content that may be present in the picture.
Press the
or
button to choose from the Off,
Low, Medium or Strong setting.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Black Level Extender
Press the
button to highlight Black Level Extender. Use this feature to increase the picture
reproduction performance in the dark areas of the picture.
Press the
or
button to turn this feature On or Off.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
White Peak Limiter
Press the
button to highlight White Peak Limiter. Use this feature to limit excessive white in bright
areas of the picture, caused by a lower sync level for a channel being received from the antenna or cable.
Press the
or
button to turn this feature On or Off.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
CTI
Press the
button to highlight CTI (Color Transient Improvement). This feature can be used to reduce
the time taken to transition from one color to another. The effect will be seen as sharpening the border
between colors.
Press the
or
button to choose from the Off, Low, Medium or Strong setting.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
39
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Flesh Tone
Press the
button to highlight Flesh Tone. In
some cases, activation of this feature can result in
a more pleasing production of sky and flesh color.
Press the
or
button to turn this feature On
or Off.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
Adaptive Luma
Press the
button to highlight Adaptive Luma. Large areas of darkness in a picture will result in a
lower Average Picture Level (APL) and the overall picture will look too dark; activation of this feature will
raise the APL to counteract this effect.
Press the
or
button to turn this feature On or Off.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
40
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.3 DTV / TV Input Audio Adjustment
4.3.1 Volume
When the MENU button is pressed, the On Screen
Display (OSD) appears on the PICTURE
adjustment page.
Press the
button to display the AUDIO
ADJUST page.
Press the
button to highlight the Volume
selection.
Press the
button to start adjusting the volume
and the menu page will disappear and be replaced
by a small Volume Indicator Bar so you can see
the volume level between the zero and maximum
available levels.
Use the
or
button to adjust the level.
The Volume Indicator Bar will also appear when watching a program on your TV is the Volume button on
the remote or the side of the TV is pressed.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.3.2 Bass
Press the
button to highlight the Bass selection.
Press the
button to start adjusting the bass and the menu page will disappear and be replaced by a
small Bass Indicator Bar, as before, so you can see the bass level between the zero and maximum
available levels.
Use the
or
button to adjust for bass boost or
attenuation.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
Version 12/7/2007
41
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.3.3 Treble
Press the
button to highlight the Treble selection.
Press the
button to start adjusting the treble and the menu page will disappear and be replaced by a
small Treble Indicator Bar, as before, so you can see the treble level between the zero and maximum
available levels.
Use the
or
button to adjust for treble boost or attenuation.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.3.4 Balance
Press the
button to highlight the Balance
selection.
Press the
button to start adjusting the balance
and the menu page will disappear and be
replaced by a small Balance Indicator Bar, as
before, so you can see the balance adjustment to
the left or right of the nominal position.
Use the
or
button to adjust the left/right
balance.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.3.5 Surround
Press the
button to highlight the Surround selection.
Press the
button to select for the simulated surround sound feature to be On or Off.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.3.6 Digital Audio Out
Press the
button to highlight the Digital Audio Out selection.
Press the
or
button to make the proper selection. The options being OFF, Dolby Digital and PCM.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
42
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.3.7 Speakers
Press the
button to highlight the Speakers selection.
Press the
button to turn the internal speakers On or Off. You may want to turn-off the internal
speakers when listening to the audio through your Home Theatre System.
4.3.8 Lip Sync
Included with the advanced technology of your TV, a feature which will compensate the shortcomings of
signal transmission called audio sync (Lip Sync). Lip Sync is designed to adjust the audio of the program
being viewed so that it matches the movement of the lips of someone talking on the screen. This feature
is built into your set, and it can be applied to all inputs. To use this feature, follow the steps below.
Press the MENU key to bring up the OSD.
Using either the
or
button scroll across to
the microphone icon, the Audio menu will be
displayed.
Press either
or
button to scroll either up or
down to Lip Sync.
Press either
or
button to make the
appropriated adjustment.
Press the LAST key once to return to the previous
screen or repeatedly to return to your program if
task has been completed.
Version 12/7/2007
43
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.4 DTV / TV Tuner Setup
When you first used your VW46L FHDTV10A you will have setup your TV for DTV / TV channels using
the Initial Setup screens. If you did not do this or if your setup has changed, you can do this from the TV
TUNER SETUP menu.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.4.1 Tuner Mode
When the MENU button is pressed, the On Screen
Display (OSD) appears on the PICTURE
adjustment page. Press the
button to display
the TV page.
Press the
button to highlight the Tuner Mode
selection.
Press either the
or
button to choose Cable
or Air (Antenna) depending upon which equipment
you have attached to the DTV / TV Input.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.4.2 Auto Search
Press the
button to highlight the Auto Search
selection.
Press the
button to Auto Search for TV
channels available. The TV will automatically
search for analog and digital channels.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.4.3 Skip Channel
After the TV has stored all of the available DTV channels in memory you will find that some channels will
be too weak to watch comfortably or they may be channels you do not want to see. Select the channel
you wish to remove, press the MENU key
.
Press the
buttons to open the TV TUNER SETUP menu.
Press the
button to highlight SKIP CHANNEL.
Press the
button to select this channel to be skipped when using the CH+ or CH- button. You will still
be able to select this channel using the number buttons on the remote control.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
44
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.4.4 MTS
This feature allows you, the user to select the different languages in which the signal provider or
broadcaster is transmitting the audio with the program you are watching. This signal is usually or in most
cases Spanish language.
Press the
button repeatedly to scroll down to this option and get it highlighted.
Press either
or
button to go through the settings of this feature to make your selection.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.4.5 Time Zone
Setting the correct Time Zone for your area will ensure that the correct program times are shown after
pressing the GUIDE button on the remote control.
Press the
button to highlight the Time Zone selection.
Press the
button to select your area.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.4.6 Daylight Saving
As for Time Zone, setting the daylight saving time
for your area will ensure that the correct program
times are shown after pressing the GUIDE button
on the remote control.
Press the
button to highlight the Daylight
Saving selection.
Press the
button to select On or Off.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
Version 12/7/2007
45
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.5 DTV / TV Input Setup
4.5.1 Language
When the MENU button is pressed, the On Screen
Display (OSD) appears on the PICTURE
adjustment page. Press the
button until the
SETUP page is displayed.
Press the
button to highlight the Language
selection. The default is English.
Press the
button to select Español or Français.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.5.2 Sleep Timer
Press the
button to highlight the Sleep Timer selection.
Press the
button to select the timer to turn-off the TV in 30, 60, 90 or 120 minutes.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.5.3 Wide
The Wide option is the feature which allows you to select how your display would be size wise. When in
TV mode; the selections are Normal, Wide and Panoramic views.
Press the
button as many times as it takes to scroll down to this option and highlight it.
Press either or button to make the correct selection, you will see the screen adjusting to the different
sizes which apply to this feature.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
46
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.5.4 Input Naming
This feature has been added to facilitate you, the
user in identifying or label the input and signal
which is being watched. You could use up to 8
characters; either letters or numbers or
combinations of both.
Press
button to highlight this option.
Press
button to obtain the next screen which
shows the different inputs.
Press
button to select the desired input which
you want to label or name (Examples: VCR, DVD,..,
etc.) it with any name which will make easier for
you to recognize it.
Press the MENU key to go to the first space (_) in
the bracket.
Press either the
or
button and select either
the letter or number belongs to this place.
Press the
button to go to the next space (_) and
again
Using either the
or
button select the second
character of the name given to this Input.
Repeat the last previous two steps until the name of
the input is completed.
Press the MENU key to accept the name of the
input or the LAST key to cancel the setting.
Press the LAST key when you have finished to go
back to the previous menu.
Since you are already in this feature; it is
recommendable to name all the Inputs which are
being used as well as these for which you have an
idea what their name is going to be.
Press the LAST key once to return to the previous
screen or repeatedly to return to your program if
task has been completed.
Version 12/7/2007
47
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.5.5 Closed Caption (CC)
When watching regular analog (NTSC) TV, the Analog CC feature is available in the Setup menu.
Press the
button to highlight the Analog CC selection.
Press the
button to select CC1, CC2, CC3 or CC4.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Closed Caption for regular TV is usually CC1 or CC2.
4.5.6 Closed Caption On Mute
When selecting Closed Caption as a feature to be used; Closed Caption On Mute will provide you with
the option to obtain closed captioning when you press the key labeled mute on your Remote Control.
Press
button as many times as it takes to get this option highlighted.
Press either
or
button to toggle between Off and On to make the correct selection.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
48
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.5.7 Digital Closed Caption
When watching DTV, the Digital CC Style feature is available in the Setup menu.
Press the
button to highlight the Digital CC Style selection.
Press the
button to go to the next screen.
Press either
or
button to toggle between the two options; As Broadcaster and Custom.
If Custom is selected then you will have the way of
customize the way Closed Caption will be
displayed by changing these different parameters
to your like: Font Size (letters size), Font Color
(letters color) Font Opacity (transparency of the
letters), Background Color (color of the
background area where Closed Caption is going to
be displayed), Background Opacity (allows to
either see through at the scene being played or it
could be a solid screen), Window Color (it gives
the color to the area where characters will be
displayed on) and finally Window Opacity (allows
the area to be of the characters to be changed).
There are no recommendations of setting these parameters since you, the user would have your own
taste or like of them.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.5.8 Reset All Settings
Press the
button to highlight the Reset All Settings selection.
Press the
button to reset the TV to the default factory settings.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Note: This does NOT reset the Parental Control Password.
Version 12/7/2007
49
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.6 DTV / TV Input Parental Control
4.6.1 Channel Block
If you want to restrict certain channel and program viewing, you can do this by turning on the Parental
Control. Selected programs, movies and channels
can then be made available only after an
authorized password has been entered and
accepted by the TV.
When the MENU button is pressed, the On Screen
Display (OSD) appears on the PICTURE
adjustment page.
Press the
button to display the PARENTAL
page.
Press the
button to highlight the PASSWORD
selection.
The Password must be entered before the TV will continue with Parental settings. The default password
set in the factory is 0 0 0 0. If you are going to use the Parental Control feature you should change the
password.
Note: Make sure you write down and store the new password in a secure place.
The Reset All Settings feature (see page 49) does NOT reset the password.
Press the
button to highlight the Channel Block
selection.
Press the
button to turn it on or off.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
Version 12/7/2007
50
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.6.2 TV Rating
Follow the procedure in the previous section 4.6.1
to display the Parental Control menu and then
press the
button to highlight the TV Rating
selection.
Press the
button and the Block TV Rating
panel will be displayed.
In the Block TV Rating panel you can customize
the program blocking of the following TV ratings:
Y – All children
Y7 – Older children
G – General audience
PG – Guidance suggested
14 – Strongly cautioned
MA – Mature audience
You can also customize the TV ratings for the
following content:
A – Sexual dialog
D – Sexual dialog
L – Adult language
S – Sexual situations
V - Violence
FV – Fantasy violence
Press the
or
button to navigate through the
TV rating options.
Press the MENU button to block (locked) or allow (unlocked).
Version 12/7/2007
51
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.6.3 Movie Rating
Press the
button to highlight the Movie Rating selection.
Press the
button and the Block Movie Rating panel will be displayed.
In the Block Movie Rating panel you can
customize the program blocking of the following
Movie ratings:
G – General audience
PG – Parental guidance suggested
PG-13 – Recommended for children 13 years of
age or older
R – Mature audience
NC-17 – No one under 17 years of age
X – No one under 17 years of age
Press the
or
button to navigate through the
Movie rating options.
Press the MENU button to block (locked) or allow (unlocked).
4.6.4 Check for New DTV Rating
This option is designed to update the TV or Movie table of different ratings for programs being viewed in
your local or regional area. It will allow the parental
guidance control feature in your TV to have the
most current parental control database for a digital
signal. This option may be available in the future
for activation. This option works as follows:
Whenever you decide to use the Parental Control
feature and this option has been activated in your
area, the Check for New DTV Rating will be a solid
color indicating that an update is available for the
TV Rating or Movie Rating table. After entering the
password, the Parental menu will appear on the
screen, and then do the following.
Observe the status of the Check for New DTV
Rating. If option is faded out, no update is available (the option is not activated in your area). If it is not
faded out,
press either
or
button to select this option.
Press
button to execute this operation. Please follow the on screen instructions to complete this
procedure.
Press either
or
to select and then adjust any other option in this menu.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
52
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.6.5 Blocked Unrated Programming
Follow the procedure in the previous section 4.6.1
to display the Parental Control menu and then
press the
button to highlight the Block Unrated
TV selection.
Press the
button to turn-on or turn-off the
blocking of programming that does not have a
rating.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.6.6 Change the Password
Press the
button to highlight the Access Code
Edit selection.
Press the
button and the new Password panel
will be displayed.
Enter the new, 4-digit password using the number
buttons on the remote. Enter it a second time to
confirm you entered it correctly.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
Note: Make sure you write down and store the new password in a secure place.
The Reset All Settings feature (see page 49) does NOT reset the password.
Version 12/7/2007
53
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.7 HDMI Input Picture Adjustment
The Picture Adjust menu operates in the same
way for the HDMI Input as for the DTV / TV input
in section 4.2. The menu difference is that there
is no icon along the top for DTV / TV or Parental
Control adjustments.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.8 HDMI Input Audio Adjustment
The Audio Adjust menu operates in the same way
for the HDMI Input as for the DTV / TV input in
section 4.3. The menu difference is that there is
no icon along the top for DTV / TV or Parental
Control adjustments.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.9 HDMI Input Setup
The Setup menu operates in the same way for the
HDMI Input as for the TV input in section 4.4. The
menu difference is that there is no icon along the
top for DTV / TV or Parental Control adjustments.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
Version 12/7/2007
54
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.10 Video Input Picture Adjustment
The Picture Adjust menu operates in the same
way for Video Inputs (Component and AV) as for
the DTV / TV input in section 4.2. The menu
difference is that there is no icon along the top for
DTV / TV adjustments.
4.11 Video Input Audio Adjustment
The Audio Adjust menu operates in the same way
for Video Inputs (Component and AV) as for the
DTV / TV input in section 4.3.
The menu
difference is that there is no icon along the top for
DTV / TV adjustments.
4.12 Video Input Setup
The Setup menu operates in the same way for
Video Inputs (Component and AV) as for the TV
input in section 4.4. The menu difference is that
there is no icon along the top for TV adjustments.
Version 12/7/2007
55
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.13 Video Input Parental Control
The Parental Control menu operates in the same
way for Video Inputs (Component and AV) as for
the DTV / TV input in section 4.6. The menu
difference is that there is no icon along the top for
DTV / TV adjustments.
4.14 PC Input Picture Adjustment
The Picture Adjust menu operates in the same way for the PC Input as for the DTV / TV input in section
4.2 for Backlight, Contrast, Brightness and Color Temperature.
4.14.1 Auto Adjust
When the MENU button is pressed, the On Screen
Display (OSD) appears on the PICTURE
adjustment page.
Press the
button to highlight the Auto Adjust
selection.
Press the
button for the LCD HDTV to adjust to
the PC signal timing automatically.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.14.2 Backlight
Press the
button to highlight the Backlight selection.
Press the
button to start adjusting the brightness of the Backlight and the menu page will disappear
and be replaced by a small Backlight Indicator Bar so you can see the light level between the minimum
and maximum available levels.
Use the or
button to adjust the level.
The Backlight level does not affect the Brightness (black level) or Contrast (white level) of the picture, it
adjusts the lamp current and this affects the overall brilliance of the picture.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
56
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.14.3 Brightness
Press the
button to highlight the Brightness selection.
Press the
button to start adjusting the brightness and the menu page will disappear and be replaced
by a small Brightness Indicator Bar so you can see the brightness level between the minimum and
maximum available levels.
Use the
or
button to adjust the level.
The Brightness adjusts the black levels in the picture. If the brightness is too low you will not be able to
see the detail in darker parts of the picture and if the brightness is too high the picture will look washed
out.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.14.4 Contrast
Press the
button to highlight the Contrast
selection.
Press the
button to start adjusting the contrast
and the menu page will disappear and be replaced
by a small Contrast Indicator Bar so you can see
the contrast level between the minimum and
maximum available levels.
Use the
or
button to adjust the level.
The Contrast adjusts the white levels in the picture. If the contrast is too low the picture will look washed
out and if the contrast is too high you will not be able to see any detail in the bright parts of a picture.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
57
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.14.5 Color Temperature
Press the
button to highlight the option for
Color Temperature selection.
The default is COOL; this is the 9300K setting.
Press the or
button if you want to choose the
Warm, Normal or Custom option.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
If you choose the Custom option, then a new menu will be displayed showing the primary color items,
Red, Green and Blue. Press the
button to highlight the color you wish to adjust.
Press the
button to start adjusting the color and the menu page will disappear and be replaced by a
small Color (Red, Green or Blue) Indicator Bar as before.
Use the
or
button to adjust the color.
Press the LAST button when finished. Repeat the procedure to adjust the other colors if desired.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.14.6 H-SIZE
Press the
button to highlight the H-Size
selection.
Press the
button to start adjusting the
horizontal size of the picture.
Use the
or
button to adjust the horizontal
size.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
Version 12/7/2007
58
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.14.7 H. Position
Press the
button to highlight the Horizontal Shift selection.
Press the
button to start adjusting the horizontal position of the picture.
Use the
or
button to adjust the horizontal position.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
4.14.8 V. Position
Press the
button to highlight the Vertical Shift
selection.
Press the
button to start adjusting the vertical
position of the picture.
Use the
or
button to adjust the vertical
position.
Once the adjustments are completed press the
LAST button repeatedly to exit the OSD
completely.
4.14.9 Fine Tune
Press the
button to highlight the Fine Tune selection.
Press the
button to start tuning the to the PC signal.
Use the
or
button to adjust the tuning.
Once the adjustments are completed press the LAST button repeatedly to exit the OSD completely.
Version 12/7/2007
59
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.15 PC Input Audio Adjustment
The Audio Adjust menu operates in the same way
for the PC Input as for the DTV / TV input in
section 4.3. The menu difference is that there are
no icons along the top for DTV / TV and Parental
Control adjustments.
4.16 PC Input Setup
The Setup menu operates in the same way for the
PC Input as for the DTV / TV input in section 4.4.
The menu difference is that there is no icon along
the top for TV adjustments and no Closed Caption.
Version 12/7/2007
60
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.17 Understanding Viewing Features
Your HDTV features four viewing modes. You can switch viewing modes using the remote control; please
see instructions in page 32.
4.17.1 Viewing Modes
Normal Mode
The original 4:3 aspect ratio (1.33:1 source) is preserved, so black bars are
added to the left and right of the display image. Standard TV broadcasts are
displayed with a 4:3 Aspect Ratio. Movies in 4:3 Aspect Ratio may be referred
to as pan-and-scan or full frame. These movies were originally filmed in 16:9
(widescreen), and then modified to fit a traditional TV screen (4:3).
Wide Mode
When watching a standard broadcast or full-frame movie in this mode,
the display image is stretched proportionately to fill the TV screen.
When watching a widescreen (1.78:1 source) program or movie, the
display image fills the TV screen. If you are watching a widescreen
(1.85:1 or 2.35:1 source) program or movie, there will still be black
bars at the top and bottom.
When watching a standard definition 4:3 aspect ratio (1.33:1 source)
the picture will fill the screen but will be stretched horizontally; people
will look fatter than they are.
Zoom Mode
When watching a widescreen (1.78:1, 1.85:1, or 2.35:1 source)
program or movie, the display image is zoomed proportionally to fill the
width of the screen. The top and bottom are cut off to remove most of
the source material’s black bars. This mode is good for programs or
movies with sub-titles.
Panoramic Mode
When watching a standard broadcast or full frame movie in this mode,
the 4:3 Aspect Ratio (1.33:1 source) display image is stretched
horizontally on the left and right sides to fill the TV screen. The center of
the image is not stretched.
Note: Viewing modes are saved based on input. For example, you lasted
watched a DVD in widescreen mode and then watched TV in standard mode.
When you switch back to DVD input, the viewing mode will return to widescreen.
Version 12/7/2007
61
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
4.17.2 Using a Cable or Satellite Remote
Your VIZIO remote uses codes 11758 and 10178 to work your LCD HDTV. To use a cable or satellite
remote to work the LCD HDTV, refer to your cable or satellite remote user guide for more information on
how to program the remote. If your cable or satellite remote uses a 5-digit code (like most Direct TV
units), first try 11758 and then, if that does not work, 10178. If your cable or satellite remote uses a 4digit code, try 1758 and then 0178 as an alternative. If your cable or satellite remote uses a 3-digit code
(Echostar or Dish Network for example), use code 627.
Note: Some buttons may not function as expected on your cable or satellite remote. Typically power,
volume and mute will work.
Version 12/7/2007
62
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Chapter 5 Maintenance and Troubleshooting
5.1 Maintenance
Important
1.
2.
Make sure that the power cable is removed from the socket before cleaning the TV.
Do not use volatile solvent (such as toluene, rosin and alcohol) to clean the TV. Such
chemicals may damage the housing, screen glass and remote control, and cause paint to
peel.
Cleaning the Housing and Remote Control
1.
2.
Use a soft cotton cloth for cleaning.
If the housing or remote control is seriously contaminated, use a soft cloth moistened with
diluted neutral cleaner to clean the display. Wring water out of the cloth before cleaning to
prevent water from penetrating into the housing. Wipe the display with a dry cloth after
cleaning.
Cleaning the Screen
1.
2.
Use a soft cotton cloth to gently clean the screen.
The screen glass is very fragile. Do not scrape it with any sharp object. Do not press or tap
the screen to avoid cracking. When the screen is seriously contaminated, use a soft cloth
moistened with diluted neutral cleaner to clean the display. Wring water out of the cloth
before cleaning to prevent water from penetrating into the housing. Wipe the display with a
dry cloth after cleaning.
Version 12/7/2007
63
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
5.2 Troubleshooting Guide
If the TV fails or the performance changes dramatically, check the display in accordance with the
following instructions. Remember to check the peripherals to pinpoint the source of the failure. If the
display still fails to perform as expected, contact the VIZIO for assistance by calling 1-(949) 428-2525 or
e-mail us at techsupport@vizio.com.
Problem
Solution
No power.
Make sure the power button is ON (White VIZIO Logo).
Make sure AC power cord is securely connected to the AC socket.
Plug another electrical device (like a radio) to the power outlet to verify that the
outlet is supplying the proper voltage.
No sound.
Check your audio connection
Press MUTE on the remote control, so that mute symbol disappears from the screen
Check your audio settings, your TV audio may be set to SAP, min or speakers off
Press the Volume + (Up) key on your remote control
Make sure that headphones are not connected
If the screen is black.
Check your input connections.
Power is ON but no screen
image.
Make sure the video cable supplied with the TV is secured to the correct video
output port on the back of the VCR and the TV. Make any cable you have attached
to the TV is secured to the correct output your Set-Top Box, DVD, etc.
Adjust brightness and contrast.
Check Source settings.
Wrong or abnormal colors
appear.
If any colors (red, green, or blue) are missing, check the video cable to make sure it
is securely connected.
Control buttons do not work.
Press only one button at a time.
Remote
work.
Make sure batteries are inserted correctly
Batteries could be weak.
Control
does
not
There appears to be image
quality issues.
For best image quality, view HD wide screen programs where possible. If HD
content is not available view “Standard Definition” from a digital source. Standard,
analog TV will always be noticeably inferior to HD because your digital flat panel TV
has video that is many times better than old TV’s and so you can see interference
and deficiencies you did not know you had.
You cannot see a picture.
Make sure that the power cord is plugged into a grounded electrical outlet.
Make sure that the power button is turned on.
Make sure that the selected input source is connected to a working input source.
If your TV is connected to your computer in RGB or HDMI mode, press any key on
your keyboard to “wake” your computer.
You see a distorted picture or
hear unusual sound.
You may be getting interference from electrical appliances, cars, motorcycles, or
fluorescent lights. If you have not mounted it on the wall, try moving your TV to
another location to see if this is the cause of the problem.
The picture has abnormal
patterns.
Make sure that the input source cable is attached securely and correctly to the back
of your TV.
Make sure that the video input source is within the range of your TV. Compare the
video input source’s specifications with your TV specifications.
The display image does not
cover the entire screen.
If you are using RGB mode, make sure that H Size and V Position in the On Screen
Display (OSD) are set correctly.
Version 12/7/2007
64
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Problem
Solution
If you are using TV, AV-C, AV-S or Component with 480i input, please follow the
instructions on page 32 on how to scroll through various screen modes.
You can see a picture but you
cannot hear sound.
Make sure that the volume is not turned down.
Make sure that the sound is not muted.
Make sure that your audio input source cables are connected securely and correctly.
The TV has pixels that are
always dark or colored.
Your LCD HDTV is manufactured using an extremely high level of precision
technology, however, sometimes some pixels of your LCD HDTV may not display.
Pixel defects within industry specifications are inherent to this type of product and do
not constitute a defective product.
You see “noise” or “trash” on
the screen.
When your LCD HDTV’s digital capabilities exceed a digital broadcast signal, the
signal is up-converted (increased) to match your TV’s display capabilities. Upconverting can cause noise or trash.
You switch to a different input
and the volume changes.
The TV remembers the volume level from the last time you adjusted it. If the sound
level is higher or lower from another source, then the loudness will change.
You switch to a different input
and the screen size changes.
The TV remembers the viewing mode from the last time you used a particular input
(AV, Component, HDMI and TV).
Tips for High-Definition Users.
The LCD HDTV is an ideal platform for viewing High Definition Content.
Best Image Quality will be achieved by the HDMI Input, then YPbPr, then RGB.
However, due to variances in broadcast practices, it is possible some image
distortions can occur.
Tips for Letterbox Content
Users.
Letterboxed (or “Widescreen”) versions of DVD movies are most commonly
formatted for standard 4:3 Televisions. The LCD HDTV has the capability of
expanding this content so the entire screen is filled at the expense of image
accuracy. Follow the instructions in page 32.
5.3 Telephone & Technical Support
Products are often returned due to a technical problem rather than a defective product that may result in
unnecessary shipping charges billed to you. Our trained support personnel can often resolve the problem
over the phone. For more information on warranty service or repair, after the warranty period, please
contact our Support Department at the number below.
Customer support and quality service are integral parts of VIZIO’s commitment to service excellence.
For technical assistance contact our VIZIO Technical Support Department via email or phone.
E-mail: techsupport@vizio.com
Tel: (877) 698-4946
Hours of operations:
6:00am – 6:00pm PST Monday – Friday
10:00am – 2:00pm PST Saturday – Sunday
Please have your VIZIO model number, serial number and date of purchase available before you call.
VIZIO
39 Tesla, Irvine, CA 92618, USA
Tel: (949) 428-2525 Fax: (949) 585-9514
Web: www.VIZIO.com
Version 12/7/2007
65
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
5.4 Compliance
Caution: Always use a power cable that is properly grounded. Please use the AC cords listed below for
each area.
USA
Canada
Germany
UK
Japan
UL
CSA
VDE
BASE/BS
Electric Appliance Control Act
5.5 FCC Class B Radio Interference Statement
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1.
Reorient or relocate the receiving antenna.
2.
Increase the separation between the equipment and receiver.
3.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4.
Consult the dealer or an experienced radio/TV technician for help.
Notice:
1.
2.
3.
The changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Shielded interface cables and AC power cord, if any, must be used in order to comply with
the emission limits.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment. It is the responsibilities of the user to correct such
interference.
Version 12/7/2007
66
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
Chapter 6 Miscellaneous Information
6.1 Specifications
Specifications
Panel
46” Diagonal, 16:9 Aspect Ratio
Resolution
1920 x 1080 pixels
Pixel (Dot) Pitch
0.530 mm (H) x 0.530 mm (V)
Display/Signal
Compatibility
1080p (FHDTV), 720p (HDTV), 480i (SDTV), 480p (EDTV), 1080i (HDTV)
Colors
16.77 Million (8-bit)
Brightness
550 cd/m2 (typical)
Contrast
2000 : 1 (typical)
Viewing Angle
Up to 178° (horizontal and vertical)
Inputs
1x Co-axial RF (ATSC/QAM/NTSC)
3x v1.3 HDMI™** with HDCP,1 with Stereo Audio RCA
2x Component YPbPr plus Stereo Audio
1x RGB PC plus Stereo Audio
1x Composite Video /S-Video plus Stereo Audio
Outputs
1x SPDIF Digital Audio (Optical). 1x Stereo Analog Audio
Features
Full HD, CC, V-Chip, 3D Comb Filter, Motion Adaptive De-Interlace, 3:2 or 2:2 Reverse Pulldown, ATSC, with 8VSB & QAM demodulation, with MPEG-2 decoding, NTSC Video decoding
via RF (Antenna or Cable) or Video (CVBS, S-Video or Component), Progressive Scan Video
via Component YPbPr, VGA or HDMI, HDTV via HDMI or Component YPbPr, Computer
640x480, 800x600, 1024x768, 1360x768, 1920x 1080 via VGA or 640x480, 1920x 1080 via
HDMI, Color Temperature of 6500K, 5400K and 9300K(Default), Independent Red, Green and
Blue adjustment for user fine tuning of color temperature, Sound Enhancement,
Speakers
Built-in, 2x10W
Panel Life
50,000 hours to half the original brightness
Power
Input
IEC Connector for direct power line connection
Voltage Range
100 ~ 240Vac at 50/60Hz
Power Consumption
340W (Max)
Environmental Conditions
Operating
Temperature: 5°C~35°C, Relative Humidity: 20~80%, Altitude: 0~14,000 ft
Non-Operating
Temperature: -20°C~50°C, Relative Humidity: 10~90%, Altitude: 0~40,000 ft
Dimensions
44.3” W X 30.5” H X 9.7” D with stand
44.3” W X 29.4” H X 4.0” D without stand
Net Weight
61.3lbs with stand; 59.1lbs without stand
Gross Weight
93lbs
Certifications
CSA/CSA-US, FCC Class B
*Product specifications may change without notice or obligation.
Version 12/7/2007
67
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
6.2 Glossary – Standard Definitions
Analog TV: Today’s TV system using radio frequency waves to transmit and display pictures and sound.
Aspect Ratio (4x3): Traditional TV “aspect ratio”, that is, the screen’s width as compared to its height.
For example, a “32 inch TV screen” would be 25 inches wide and 19 inches tall.
Aspect Ratio (16x9): “Wide screen TV” aspect ratio which is more like a movie screen than a traditional
TV. For example, a “32 inch TV screen” would be 28 inches wide and 16 inches tall.
Digital TV (DTV): Television delivered and displayed using radio frequency waves that contain
information that is digitally encoded for improved quality and efficiency.
Enhanced Definition TV (EDTV): A better digital television transmission than SDTV with at least 480P,
in a 16x9 or 4x3 display and Dolby digital surround sound. 480P is the quality used by most DVD players.
EDTV provides 300-400,000 pixels.
HDTV Monitor (sometimes called HDTV Ready): A set that can display HDTV programming if you have
a separate HDTV tuner, HD Cable Set-Top Box or HD Satellite Set-Top-Box Receiver.
HDTV Tuner (also decoder, receiver, set-top box): A device capable of receiving and outputting HDTV
signals for display. It may be stand-alone or integrated in the set.
High-Definition Television (HDTV): The best quality picture, wide screen (16x9) display with at least
720 progressively scanned lines (720P) or 1080 interlaced lines (1080i) and Dolby digital surround sound.
HDTV provides 900,000-2.1 million pixels.
Integrated HDTV: An HDTV that has the digital tuner built into the set. It does not need a separate settop box to receive over-the-air DTV signals.
Interlace Scan: A way to scan vertical lines onto a TV picture by scanning all the odd lines first, then
filling the in the even lines (this happens instantaneously).
Plug-and-Play or Digital Cable Ready: A DTV or other device for digital cable consumers that plugs
directly into the cable jack and does not require a separate set-top box. Plug-and-Play TV owners must
obtain a CableCARD from their cable company in order to view scrambled programming services.
Progressive Scan: A way to scan vertical lines onto a TV picture by scanning all the lines consecutively
(progressively). The 1080P is the latest best quality picture display at the present time.
Standard Definition TV (SDTV): Basic digital television transmission that may be displayed with fewer
than 480 progressively scanned lines (480P) in 16 x 9 or 4 x 3 format. 480 interlaced (480i) is the quality
of today’s analog TV system.
Source: Buying a Digital Television, CEA, HDTV Guide, 2005
Note: The Federal Communications Commission (FCC), the Consumer Electronics Association (CEA)
and the Consumer Electronics Retailers Coalition (CERC) have made a new tip sheet available for digital
television (DTV) retailers to reproduce and distribute to consumers on the sales floor. The file may be
downloaded online at www.dtv.gov. While you’re there, check out the other useful information in the FCC
is making available to consumers interested in learning more about the analog to digital transition.
Version 12/7/2007
68
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
6.3 Index
A
Accessories, 5
Adjustments
Selecting the Screen Size, 32, 61, 68
Stepping through TV Channels, 32
Volume, 9, 32, 64
Advanced Video Features
Adaptive Luma, 40
Black Level Extender, 39
CTI (Color Transient Improvement, 39
DNR (Dynamic Noise Reduction, 39
Flesh Tone, 40
White Peak Limiter, 39
C
Cleaning your VIZIO TV, 63
Coax (RF)
Connecting for DTV, 14
Connecting your Basic Set Top Box, 18
Component
Connecting your DVD Player, 20
Connecting your HDTV Set-Top Box, 17
Composite (AV)
Connecting your Basic Set-Top Box, 18
Connecting your DVD Player, 21
Controls
Front Panel, 9
Side Panel, 9
D
DTV
Audio Adjustment, 41
Parental Control, 50
Picture Adjustment, 35
Special Features, 46
Tuner Setup, 44
DTV Audio Adjust
Balance, 42
Bass, 41
Simulated Surround Sound, 42
Speakers On/Off, 42
Treble, 42
Volume, 41
DTV Picture Adjust
Advanced Video, 39
Backlight, 36, 56
Brightness, 36, 57
Color, 37
Color Temperature, 38, 58
Contrast, 37, 57
Picture Mode, 35
Sharpness, 38
Tint, 37
DTV Special Features
Version 12/7/2007
Closed Caption, 49
Language, 46
Reset, 49
Sleep Timer, 46
DTV Tuner Setup
Auto Search, 44
Daylight Saving, 45
Skip Channel, 44
Time Zone, 45
Tuner Mode, 44
DVI
Connecting your DVD Player, 19
Connecting your HDTV Set-Top Box, 16
G
Glossary, 68
H
HDMI
Connecting your DVD Player, 19
Connecting your HDTV Set-Top Box, 15
HDMI Input
Audio Adjustment, 54
Picture Adjustment, 54
Setup, 54
I
Inputs
Antenna, 3
Connectors, 13
Rear Label, 10
Installation
Base removal, 6
Preparation, 5
Safetey Strap, 5
Safety Instructions, 2
Wall Mounting, 5, 6, 26
O
OSD
Brightness Adjustment, 67
Color Adjustment, 13
Contrast Adjustment, 67
Outputs
Using 5.1 Surround with a Home Theatre System, 23
P
Parental Control
Block Unrated Programming, 53
Channel Block, 50
Movie Rating, 52
Password change, 53
69
www.VIZIO.com
VIZIO VW46L FHDTV10A User Manual
TV Rating, 51
PC Input
Audio Adjustment, 60
Picture Adjustment, 56
Setup, 60
PC Picture Adjust
Auto Adjust, 56
Fine Tune, 59
Horizontal Position, 59
Horizontal Size, 58
Vertical Position, 59
PC Resolutions, 25
R
Remote
Batteries, 12
Range, 12
Remote Control
Using your Cable or Satellite Remote to Operate your
VIZIO TV, 62
RGB
Connecting your PC, 24
S
Screen Size explanation, 61
S-Video
Connecting your DVD Player, 21
Connecting your VCR, 22
Connecting your Video Camera, 22
T
Technical Specifications, 67
Troubleshooting Guide, 64
TV
Audio Adjustment, 41
Parental Control, 50
Picture Adjustment, 35
Special Features, 46
TV Audio Adjust
Balance, 42
Version 12/7/2007
Bass, 41
Simulated Surround Sound, 42
Speakers On/Off, 42
Treble, 42
Volume, 41
TV Picture Adjust
Advanced Video, 39
Backlight, 36, 56
Brightness, 36, 57
Color, 37
Color Temperature, 38, 58
Contrast, 37, 57
Picture Mode, 35
Sharpness, 38
Tint, 37
TV Special Features
Closed Caption, 48
Language, 46
Reset, 49
Sleep Timer, 46
TV Tuner Setup, 44
Auto Search, 44
Skip Channel, 44
Tuner Mode, 44
V
Video Input
Audio Adjustment, 55
Parental Control, 56
Picture Adjustment, 55
Setup, 55
W
Watching TV
Basic Adjustments, 32
Basic connections, 26
First Startup, 26
Getting your Programs, 31
Program Information, 33
Status Information, 33
70
www.VIZIO.com