HT-E6500W
5.1CH Blu-ray™
Home Entertainment System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HT-E6500W_ZA_0315.indd 1
2012-03-15 오후 4:34:26
Safety Information
Warning
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER (OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash and Arrowhead
within the triangle is a warning sign
alerting you of dangerous voltage
inside the product.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The explanation point within the triangle
is a warning sign alerting you of important
instructions accompanying the product.
WARNING
CLASS 1 LASER PRODUCT
• To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
This Compact Disc player is classified as a CLASS
1 LASER product. Use of controls, adjustments
or performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
Complies with 21CFR 1040.10 except for
deviations pursuant to Laser Notice No. 50, dated
June 24, 2007.
DANGER :
• VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID DIRECT EXPOSURE TO
BEAM. (FDA 21 CFR)
CAUTION :
• CLASS 3B VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. AVOID EXPOSURE
TO THE BEAM (IEC 60825-1)
• THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVER AND DO
NOT REPAIR YOURSELF. REFER SERVICING
TO QUALIFIED PERSONNEL.
FCC NOTE (for U.S.A)
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and on.
The user is encouraged to try to correct the
interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect this equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
• This class B digital product meets all
requirements of the Canadian Interference Causing Equipment Regulations.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
PRODUCTO
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
| 2 English
HT-E6500W_ZA_0315.indd 2
2012-03-15 오후 4:34:35
Precautions
1 . Read these instructions.
Safety Information
Read these operating instructions carefully before
using the unit. Follow all the safety instructions
listed below.
Keep these operating instructions handy for future
reference.
14 . Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or plug
is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
01
Important Safety Instructions
13 . Unplug this apparatus during lightning storms
or when unused for long periods of time.
2 . Keep these instructions.
3 . Heed all warnings.
4 . Follow all instructions.
5 . Do not use this apparatus near water.
6 . Clean only with a dry cloth.
7 . Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8 . Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including AV receivers) that
produce heat.
9 . Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
10 . Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where it exits the
apparatus.
11 . Only use attachments/accessories specified
by the manufacturer.
12 . Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
Disc Storage & Management
• Holding Discs
- Fingerprints or scratches on
a disc may reduce sound and
picture quality or cause skipping.
- Avoid touching the surface of a disc where
data has been recorded.
- Hold the disc by the edges so that fingerprints
will not get on the surface.
- Do not stick paper or tape on the disc.
• Cleaning Discs
- If you get fingerprints or dirt on a
disc, clean it with a mild detergent
diluted in water and wipe with a
soft cloth.
- When cleaning, wipe gently from the inside to
the outside of the disc.
- Disc Storage
 Do not keep in direct sunlight.
 Keep in a cool ventilated area.
 Keep in a clean protection jacket and store
vertically.
Handling Cautions
• Do not expose this apparatus to dripping or
splashing. Do not put objects filled with liquids,
such as vases, on the apparatus.
• To turn this apparatus off completely, you must
pull the power plug out of the wall socket.
Consequently, the power plug must be easily
and readily accessible at all times.
• Do not touch the power plug with a wet hand.
It can cause an electric shock.
English
HT-E6500W_ZA_0315.indd 3
3|
2012-03-15 오후 4:34:35
Safety Information
• Do not plug multiple electric devices into the
same wall socket. Ovedrloading a socket can
cause it to overheat, resulting in a fire.
• Maintenance of the Cabinet
- Before connecting other components to this
product, be sure to turn them off.
- If you move your product suddenly from a
cold place to a warm place, condensation
may occur on the operating parts and lens
and cause abnormal disc playback. If this
occurs, unplug the product, wait for two
hours, and then connect the plug to the
power outlet. Then, insert the disc, and try to
play back again.
• If the product makes an abnormal noise or
produces a burning smell or smoke, turn off
the power switch immediately and disconnect
the power plug from the wall outlet. Then,
contact the nearest customer service center for
technical assistance. Do not use the product.
Using the product as it is may cause a fire or an
electric shock.
• To turn this apparatus off completely, you must
pull the power plug out of the wall socket.
Consequently, the power plug must be easily
and readily accessible at all times.
Using the 3D Function
IMPORTANT HEALTH AND SAFETY
INFORMATION FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
• Some viewers may experience discomfort while
viewing 3D TV such as dizziness, nausea, and
headaches.
If you experience any such symptom, stop
viewing 3D TV, remove the 3D Active Glasses,
and rest.
• Watching 3D images for an extended period of
time may cause eye strain. If you feel eye strain,
stop viewing 3D TV, remove your 3D Active
Glasses, and rest.
• A responsible adult should frequently check on
children who are using the 3D function.
If there are any reports of tired eyes, headaches,
dizziness, or nausea, have the child stop viewing
3D TV and rest.
• Do not use the 3D Active Glasses for other
purposes (such as general eyeglasses,
sunglasses, protective goggles, etc.)
• Do not use the 3D function or 3D Active Glasses
while walking or moving around. Using the 3D
function or 3D Active Glasses while moving
around may cause you to bump into objects,
trip, and/or fall, and cause serious injury.
• If you want to enjoy 3D content, connect a 3D
device (3D compliant AV receiver or TV) to the
product’s HDMI OUT port using a high-speed
HDMI cable. Put on 3D glasses before playing
the 3D content.
• The product outputs 3D signals only through
HDMI cable connected to the HDMI OUT port.
• As the video resolution in 3D play mode is fixed
according to the resolution of the original 3D
video, you can not change the resolution to your
preference.
• Some functions such as BD Wise, screen size
adjustment, and resolution adjustment may not
operate properly in 3D play mode.
• You must use a high-speed HDMI cable for
proper output of the 3D signal.
• Stay at least three times the width of the screen
from the TV when watching 3D images. For
example, if you have a 46 inch screen, stay 138
inches (11.5 feet) from the screen.
- Place the 3D video screen at eye level for the
best 3D picture.
• When the product is connected to some 3D
devices, the 3D effect may not function properly.
• This product does not convert 2D content into
3D.
• “Blu-ray 3D” and “Blu-ray 3D” logo are
trademarks of the Blu-ray Disc Association.
Copyright
© 2012 Samsung Electronics Co.,Ltd.
All rights reserved; No part or whole of this user’s
manual may be reproduced or copied without the
prior written permission of Samsung Electronics
Co.,Ltd.
| 4 English
HT-E6500W_ZA_0315.indd 4
2012-03-15 오후 4:34:36
License
01
• Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,226,616;
6,487,535; 7,392,195; 7,272,567; 7,333,929;
7,212,872 & other U.S. and worldwide patents
issued & pending. DTS-HD, the Symbol, & DTSHD and the Symbol together are registered
trademarks & DTS-HD Master Audio | Essential
is a trademark of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved.
• The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
• Oracle and Java are registered trademarks of
Oracle and/or its affiliates. Other names may be
trademarks of their respective owners.
• This item incorporates copy protection
technology that is protected by U.S. patents
and other intellectual property rights of
Rovi Corporation. Reverse engineering and
disassembly are prohibited.
• This product uses Cinavia technology to
limit the use of unauthorized copies of some
commercially-produced film and videos and
their soundtracks. When a prohibited use of an
unauthorized copy is detected, a message will
be displayed and playback or copying will be
interrupted.
More information about Cinavia technology
is provided at the Cinavia Online Consumer
Information Center at http://www.cinavia.com.
To request additional information about Cinavia
by mail, send a postcard with your mailing
address to: Cinavia Consumer Information
Center, P.O. Box 86851, San Diego, CA, 92138,
USA.”
This product incorporates proprietary technology
under license from Verance Corporation and is
protected by U.S. Patent 7,369,677 and other
U.S. and worldwide patents issued and pending
as well as copyright and trade secret protection
for certain aspects of such technology. Cinavia
is a trademark of Verance Corporation.
Copyright 2004-2010 Verance Corporation. All
rights reserved by Verance. Reverse engineering
or disassembly is prohibited.
Safety Information
• Dolby and the double-D symbol are registered
trademarks of Dolby Laboratories.
• iPad, iPhone, iPod, iPod classic, iPod nano,
iPod shuffle, and iPod touch are trademarks
of Apple Inc., registered in the U.S. and other
countries.
• Open Source License Notice
- In the case of using open source software,
Open Source Licenses are available on the
product menu.
• Blu-ray Disc™, Blu-ray™, and the logos are
trademarks of Blu-ray Disc Association.
English
HT-E6500W_ZA_0315.indd 5
5|
2012-03-15 오후 4:34:36
Contents
SAFETY INFORMATION
2
3
3
3
4
4
5
Warning
Precautions
Disc Storage & Management
Handling Cautions
Using the 3D Function
Copyright
License
SETTINGS
22
24
25
26
31
31
36
GETTING STARTED
7
8
11
12
12
13
Disk and Format Compatibility
Logos of Discs the product can play
Accessories
Front Panel
Rear Panel
Remote Control
CONNECTIONS
15
15
16
16
18
18
18
18
19
19
19
20
20
20
20
21
21
21
Attaching the Toroidal Ferrite Core to the
Power Cord of the Main Unit
Connecting the Speakers
Speaker Components
Connecting The Speakers
Connecting the FM Antenna
Connecting to an iPod/iPhone
Using a USB Cable
Using a Dock
Connecting to a TV
Method 1 Connecting to a TV
with an HDMI Cable - Best Quality
(Recommended)
Method 2 Connecting to a TV with a
Video Cable - Good Quality
Connecting to External Devices
Method 1 HDMI IN : Connecting to
an External Component with an HDMI
Cable
Method 2 OPTICAL : Connecting an
External Digital Audio Component
Method 3 AUX IN : Connecting an
External Analog Component
Connecting to a Network Router
Wired Network
Wireless Network
The Initial Settings Procedure
The Home Screen
Accessing the Settings Screen
Settings Menu Functions
Auto Sound Calibration
Networks and the Internet
Upgrading Software
MEDIA PLAY
38
39
39
40
40
40
41
41
43
45
46
47
49
49
The AllShare Play Screen
Playing Files on a USB Storage Device or
iPod/iPhone
iPod/iPhone Models You Can Use with
This Product
The Function Screen
Playing Commercial Video Discs
Playing Commercial Audio Discs
Playing a Disc with User Recorded
Content
Using the AllShare Network Function
Controlling Video Playback
Controlling Music Playback
Controlling Photo Playback
Using the Tools Menu when a File is
Highlighted
Listening to Radio
Using the Special Effects Remote Control
Buttons
NETWORK SERVICES
51
53
53
Using Smart Hub
BD-LIVE™
Using Disc to Digital
55
61
64
Additional Information
Troubleshooting
Specifications
APPENDIX
| 6 English
HT-E6500W_ZA_0315.indd 6
2012-03-15 오후 4:34:37
Getting Started
Disk and Format Compatibility
02
Disc types and contents your product can play
Disc Type
Blu-ray Disc
3D Blu-ray Disc
VIDEO
DVD-VIDEO, DVD-RW,
DVD-R, DVD+RW,
DVD+R
Getting Started
Media
Details
BD-ROM or BD-RE/-R disc recorded in the BD-RE format.
DVD-VIDEO, recorded DVD+RW/DVD-RW(V)/DVD-R/+R discs that have
been recorded and finalized, or a USB storage media containing MKV, MP4
contents.
MUSIC
CD-RW/-R, DVD-RW/-R, Music recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage
BD-RE/-R
media containing MP3 or WMA contents.
PHOTO
CD-RW/-R, DVD-RW/-R, Photos recorded on CD-RW/-R, DVD-RW/-R, BD-RE/-R discs or a USB storage
BD-RE/-R
media containing JPEG contents.
| NOTE |
The product may not play certain CD-RW/-R and DVD-R because of the disc type or recording conditions.
If a DVD-RW/-R disc has not been recorded properly in DVD video format, it will not be playable.
Your product will not play content that has been recorded on a DVD-R at a bitrate that exceeds 10 Mbps.
Your product will not play content that has been recorded on a BD-R or USB device at a bitrate that exceeds 30 Mbps.
Playback may not work for some types of discs, or when you use specific operations, such as angle change and aspect ratio
adjustment. Information about the discs is written in detail on the disc box. Please refer to this if necessary.
When you play a BD-J title, loading may take longer than a normal title or some functions may perform slowly.
Disc types your product cannot play
• HD DVD
• DVD-ROM/PD/MVDisc, etc
• DVD-RAM
• Super Audio CD
(except CD layer)
• DVD-RW(VR mode)
• CVD/CD-ROM/CDV/
CD-G/CD-I/LD
(CD-Gs play audio
only, not graphics.)
• 3.9 GB DVD-R Disc
for Authoring.
| NOTE |
This product may not respond to all operating commands because some Blu-ray Disc, DVD, and CD discs allow specific or
limited operation and provide only certain features during playback.
Please note that this is not a defect in the product.
Samsung cannot guarantee that this product will play every disc bearing the Blu-ray Disc, DVD or CD logo because disc
formats evolve, and problems and errors may occur during the creation of Blu-ray Disc, DVD, and CD software and/or the
manufacture of discs.
Please contact the SAMSUNG Customer Care Center at 1-800-726-7864 if you have questions or encounter difficulty when
playing Blu-ray Disc, DVD, or CD discs in this product. Also, refer to rest of this user manual for additional information on
playback restrictions.
Some commercial discs and DVD discs purchased outside your region may not play on this product.
English
HT-E6500W_ZA_0315.indd 7
7|
2012-03-15 오후 4:34:38
Getting Started
Region Code
Logos of Discs the product can play
Both products and discs are coded by region.
These regional codes must match for a disc to
play. If the codes do not match, the disc will not
play.
The Region Number for this product is displayed
on the rear panel of the product.
Disc Type
Blu-ray Disc
DVD-VIDEO
Region
Code
Area
A
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
C
India, China, Russia, Central and
South Asia.
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America,
Central America, Australia,
New Zealand, Pacific Islands,
Caribbean
5
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
6
China
| NOTE |
If the Region number of a Blu-ray Disc/DVDs does not
correspond to the Region number of this product, the
product cannot play the disc.
Blu-ray Disc
3D Blu-ray Disc
BD-LIVE
Dolby
DTS
NTSC broadcast system in
U.S.A, Canada, Korea, Japan
Java
Supported Formats
Music File Support
File
Extension
Container
Audio
Codec
Support Range
*.mp3
MP3
MP3
-
WMA
Compliant with
WMA version 10
* Sampling rates (in
kHz) - 8, 11, 16,
22, 32, 44.1, 48
* Bitrates - All
bitrates in the
range 5kbps to
384kbps
*.wma
WMA
| 8 English
HT-E6500W_ZA_0315.indd 8
2012-03-15 오후 4:34:39
Video File Support
*.avi
AVI
*.mkv
Video Codec
Resolution
Frame rate
(fps)
Bitrate
(Mbps)
H.264 BP/MP/HP
1920x1080
6 ~ 30
25
MPEG4 SP/ASP
1920x1080
6 ~ 30
8
H.264 BP/MP/HP
1920x1080
6 ~ 30
25
MPEG4 SP/ASP
1920x1080
6 ~ 30
8
H.264 BP/MP/HP
1920x1080
6 ~ 30
25
MPEG4 SP/ASP
1920x1080
6 ~ 30
8
Window Media
Video v9
1920x1080
6 ~ 30
25
WMA
H.264 BP/MP/HP
1920x1080
6 ~ 30
25
MPEG4 SP/ASP
1920x1080
6 ~ 30
8
MP3
AAC
H.264 BP/MP/HP
1920x1080
6 ~ 30
25
MPEG4 SP/ASP
1920x1080
6 ~ 30
8
MPEG2
1920x1080
24/25/30
25
MPEG1
1920x1080
24/25/30
25
MPEG1
1920x1080
24/25/30
25
MPEG2
1920x1080
24/25/30
25
H.264
1920x1080
6 ~ 30
25
MPEG2
1920x1080
24/25/30
25
H.264
1920x1080
6 ~ 30
25
VC1
1920x1080
6 ~ 30
25
MKV
*.asf
ASF
*.wmv
WMV (wmv9)
*.mp4
MP4
*.3gp
*.vro
*.mpg
*.mpeg
*.ts
*.tp
*.trp
PS
TS
MP3
AC3
LPCM
DTS Core
MP3
AC3
LPCM
DTS Core
MP3
AC3
LPCM
WMA
AAC
3GPP
VRO
VOB
Audio Codec
Getting Started
Container
02
File Extension
AC3
MPEG
LPCM
AC3
MPEG
LPCM
AAC
AC3
AAC
MP3
DD+
 Limitations
- Even when a file is encoded by a supported codec listed above, the file might not be played if its
content has a problem.
- Normal playback is not guaranteed if the file’s container information is wrong or the file itself is
corrupted.
- Files having higher bit or frame rates than standard may stutter when played back.
English
HT-E6500W_ZA_0315.indd 9
9|
2012-03-15 오후 4:34:41
Getting Started
- The Seek (skip) function is not available if the
file’s index table is damaged.
- When you playback a file remotely through a
network connection, video playback may stutter
depending on the network speed.
 Video decoder
- Supports up to H.264 Level 4.1
- Does not support H.264 FMO/ASO/RS, VC1
SP/MP/AP L4 and AVCHD
- MPEG4 SP, ASP :
Below 1280 x 720 : 60 frames max
Above 1280 x 720 : 30 frames max
- Does not support GMC 2 or higher
 Audio decoder
- Supports WMA 7, 8, 9 and STD
- Does not support WMA 9 PRO multi-channel
files if the number of channels is more than 2 or
the files require lossless audio decoding.
- Does not support WMA sampling rate of
22050Hz mono
Notes on the USB connection
• Your product supports USB storage media,
MP3 players, digital cameras, and USB card
readers.
• The product does not support folder or file
names longer than 128 characters.
• Some USB/digital camera devices may not be
compatible with the product.
• Your product supports the FAT 16, FAT 32, and
NTFS files systems.
• Connect USB devices directly to the product’s
USB port. Connecting through a USB cable
may cause compatibility problems.
• Inserting more than one memory device into
a multi-card reader may cause the reader to
operate improperly.
• The product does not support the PTP protocol.
• Do not disconnect a USB device during a
“loading” process.
• The bigger the image resolution, the longer the
image takes to display.
• This product cannot play MP3 files with DRM
(Digital Rights Management) downloaded from
commercial sites.
• Your product only supports video that is under
30fps (frame rate).
• Your product only supports USB Mass Storage
Class (MSC) devices such as thumb drives and
USB HDD. (HUB is not supported.)
• Certain USB HDD Devices, multi-card readers
and thumb drives may not be compatible with
this product.
• If some USB devices require excessive power,
they may be limited by the circuit safety device.
• If playback from a USB HDD is unstable, provide
additional power by plugging the HDD into a
wall socket. If the problem continues, contact
the USB HDD manufacturer.
• You must remove the USB storage device safely
(by performing the “Safely Remove USB”
function) to prevent possible damage to the
USB memory.
Press the HOME button to move to the home
menu, press the YELLOW (C) button, and then
press the E button.
• SAMSUNG is not responsible for any data file
damage or data loss.
AVCHD
(Advanced Video Codec High Definition)
• This product can play back AVCHD format
discs. These discs are normally recorded and
used in camcorders.
• The AVCHD format is a high definition digital
video camera format.
• The MPEG-4 AVC/H.264 format compresses
images with greater efficiency than the
conventional image compressing format.
• Some AVCHD discs use the “x.v.Color” format.
This product can play back AVCHD discs that
use the “x.v.Color” format.
• “x.v.Color” is a trademark of Sony Corporation.
• “AVCHD” and the AVCHD logo are trademarks
of Matsushita Electronic Industrial Co., Ltd. and
Sony Corporation.
| 10 English
HT-E6500W_ZA_0315.indd 10
2012-03-15 오후 4:34:42
| NOTE |
Some AVCHD format discs may not play, depending on the recording conditions.
02
AVCHD format discs need to be finalized.
Getting Started
“x.v.Color” offers a wider color range than normal DVD camcorder discs.
Some MKV and MP4 format discs may not play, depending on their video resolution and frame rate.
Accessories
Check for the supplied accessories below.
(For Power cord)
Video Cable
(AH39-40001T)
FM Antenna
(AH42-00021A)
Soft Cloth
(AH81-02286C)
Toroidal Ferrite Core
(3301-000144)
FUNCTION
TV
SOURCE
RECEIVER
SLEEP
BD
TV
1
2
3
4
5
6
7
8
9
DISC MENU
TITLE MENU
0
POPUP
MUTE
VOL
S/W LEVEL
TUNING
/ CH
HOME
REPEAT
TOOLS
INFO
EXIT
RETURN
TUNER
MEMORY
A
SMART
B
C
MO/ST
D
SEARCH 'ĺ' 3D SOUND
HUB
Disc2Digital PANDORA SUBTITLE
SOUND
EFFECT
User Manual
(AH68-02463A)

iPod Dock
(AH96-00051C)
ASC microphone
(AH30-00099A)
Remote Control (AH59-02402A)/
Batteries (AAA size) (4301-000116)
Figures and illustrations in this User Manual are provided for reference only and may differ from actual
product appearance.
English
HT-E6500W_ZA_0315.indd 11
11 |
2012-03-15 오후 4:34:42
Getting Started
Front Panel
VACUUM
TUBE AMP
VOLUME CONTROL
OPEN/CLOSE
ENTER
PLAY/PAUSE
DISC TRAY
STOP
FUNCTION
POWER
ASC IN
5V 500mA
DISPLAY
ASC IN
REMOTE CONTROL SENSOR
USB HOST
| NOTE |
If Cellular phone or mobile device is near vacuum tube amp, or put other electronic products on the top of the product would
cause noise from the audio.
Please be careful that children do not touch the product's surface When the set is on working. It would be hot.
To upgrade the product's software through the USB Host jack, you must use a USB memory stick.
When the product displays the Blu-ray Disc menu, you cannot start the movie by pressing the 6 button on the product or
the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the E button.
Rear Panel
AUX
IN
SPEAKERS OUT
COOLING FAN
VIDEO
OUT
FM ANT
FM ANTENNA
OPTICAL
SPEAKER IMPEDANCE : 3
iPod
LAN
WIRELESS
HDMI OUT
1
HDMI IN
DIGITAL
AUDIO IN
2
VIDEO OUT
iPod
AUX IN
AUX
IN
SPEAKERS OUT
VIDEO
OUT
FM ANT
OPTICAL
SPEAKER IMPEDANCE : 3
SPEAKER OUTPUT
CONNECTORS
iPod
LAN
LAN TERMINAL
WIRELESS
HDMI OUT
HDMI OUT
TX CARD CONNECTION
(WIRELESS)
1
HDMI IN
2
DIGITAL
AUDIO IN
HDMI IN
EXTERNAL DIGITAL
AUDIO IN (OPTICAL)
| NOTE |
Maintain a minimum of 4 inches of clear space on all sides of the home theater to ensure adequate ventilation. Do not
obstruct the cooling fan or ventilation holes.
| 12 English
HT-E6500W_ZA_0315.indd 12
2012-03-15 오후 4:34:46
Remote Control
02
Tour of the Remote Control
FUNCTION
TV
SOURCE
To change to TV mode, press the
TV button.
RECEIVER
To change to Home Theater,
press the BD button.
Press numeric buttons to operate
options.
SLEEP
BD
To open and close the disc tray.
1
2
3
4
5
6
7
8
9
TITLE MENU
0
Press to view the disc menu.
POPUP
Press to stop/play a disc.
Press to pause a disc.
Cut off the sound temporarily.
MUTE
VOL
S/W LEVEL
TUNING
/ CH
Press to use Netflix.
HOME
REPEAT
Press to move to the Home screen.
These buttons are used both for
menus on the product and also
several Blu-ray Disc functions.
TOOLS
Use to adjust the level of the
subwoofer.
INFO
Use to display the playback
information when playing
a Blu-ray/DVD disc.
EXIT
RETURN
A
SMART
B
MO/ST
C
D
SEARCH 'ĺ' 3D SOUND
Disc2Digital PANDORA SUBTITLE
Press to exit the menu.
Use to set a preset radio frequency.
TUNER
MEMORY
HUB
Press to use Smart Hub.
Search for active FM stations and
to change channels.
Allows you to repeat a title,
chapter, track or disc.
Select on-screen menu items and
change menu values.
Return to the previous menu.
Use to enter the Popup menu/
Title menu.
Press to search backwards or
forwards.
Press to skip backwards or forwards.
Press to use the Tools menu.
Set a Sleep time to shut off the
product.
TV
DISC MENU
Adjust the volume.
Getting Started
Turn the product on and off.
Press to select Blu-ray's mode
(HDMI1, AUX, BD/DVD, etc.).
or
Press to select TV's video mode.
SOUND
Select MONO or STEREO for radio
broadcasts.
Press to apply 3D sound effect.
EFFECT
Press to use Disc2Digital.
Press to apply sound effects.
Press to search contents.
Press to enjoy an ordinary 2D video
in 3D mode.
Press to use Pandora.
Selects the disc subtitle language.
English
HT-E6500W_ZA_0315.indd 13
13 |
2012-03-15 오후 4:34:49
Getting Started
Installing batteries in the Remote
Control
Battery size: AAA
1
TV Control Codes
Brand
Code
Brand
Code
Admiral
(M.Wards)
56, 57, 58
Mitsubishi/
MGA
18, 40, 59, 60, 75
A Mark
01, 15
MTC
18
NEC
18, 19, 20, 40, 59, 60
Anam
01, 02, 03, 04, 05,
06, 07, 08, 09, 10, 11,
12, 13, 14
Nikei
03
Onking
03
AOC
01, 18, 40, 48
Onwa
03
Bell & Howell
(M.Wards)
57, 58, 81
Panasonic
06, 07, 08, 09, 54, 66,
67, 73, 74
Brocsonic
59, 60
Penney
18
Candle
18
Philco
03, 15, 17, 18, 48, 54,
59, 62, 69, 90
2
| NOTE |
Cetronic
03
Make sure to match the “+” and “–” ends of the batteries
with the diagram inside the compartment.
Citizen
03, 18, 25
Cinema
97
Classic
03
Assuming typical TV usage, the batteries last for about
one year.
Concerto
18
Contec
46
The remote control can be used up to approximately 23
feet (7 meters) from the product in a straight line.
Coronado
15
Craig
03, 05, 61, 82, 83, 84
Setting up the Remote Control
You can control certain functions of your TV with
this remote control.
To operate a TV with the Remote Control
Philips
15, 17, 18, 40, 48,
54, 62, 72
Pioneer
63, 66, 80, 91
Portland
15, 18, 59
Proton
40
Quasar
06, 66, 67
Radio Shack
17, 48, 56, 60, 61, 75
18, 59, 67, 76, 77, 78,
92, 93, 94
03, 19
62
RCA/Proscan
Crown
03
Realistic
Curtis Mates
59, 61, 63
Sampo
40
CXC
03
Samsung
Daewoo
02, 03, 04, 15, 16, 17,
18, 19, 20, 21, 22, 23,
24, 25, 26, 27, 28,
29, 30, 32, 34, 35, 36,
48, 59, 90
00, 15, 16, 17, 40, 43,
46, 47, 48, 49,
59, 60, 98
Croslex
Sanyo
19, 61, 65
Scott
03, 40, 60, 61
1 . Press the TV button to set the remote control
to TV mode.
Daytron
40
Sears
15, 18, 19
Dynasty
03
Sharp
15, 57, 64
2 . Turn on your TV.
Emerson
03, 15, 40, 46, 59, 61,
64, 82, 83, 84, 85
19, 65
Signature
2000
(M.Wards)
57, 58
Fisher
3 . While holding down the POWER button,
enter the code corresponding to your brand
of TV.
• If there is more than one code listed for
your TV in the table, enter one at a time to
determine which code works.
• Example : For a Samsung TV
While holding down the POWER button,
use the number buttons to enter 00. If that
does not work, try 15, then 16, etc.
4 . If the TV turns off, the setting is complete.
• You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
| NOTE |
The remote control may not work on some brands of TV's.
Also, some operations may not be possible, depending on
your brand of TV.
The remote control will work with Samsung TVs by
default.
Funai
03
Sony
50, 51, 52, 53, 55
Futuretech
03
Soundesign
03, 40
General
Electric (GE)
06, 40, 56, 59, 66,
67, 68
Spectricon
01
Hall Mark
40
Hitachi
15, 18, 50, 59, 69
SSS
18
Sylvania
18, 40, 48, 54, 59,
60, 62
Inkel
45
Symphonic
61, 95, 96
JC Penny
56, 59, 67, 86
Tatung
06
JVC
70
Techwood
18
KTV
59, 61, 87, 88
Teknika
03, 15, 18, 25
KEC
03, 15, 40
TMK
18, 40
KMC
15
Toshiba
19, 57, 63, 71
01, 15, 16, 17, 37,
38, 39, 40, 41, 42,
43, 44
Vidtech
18
LG (Goldstar)
Videch
59, 60, 69
Luxman
18
Wards
15, 17, 18, 40, 48,
54, 60, 64
LXI (Sears)
19, 54, 56, 59, 60, 62,
63, 65, 71
Yamaha
18
Magnavox
15, 17, 18, 48, 54, 59,
60, 62, 72, 89
York
40
Yupiteru
03
Marantz
40, 54
Zenith
58, 79
Matsui
54
Zonda
01
MGA
18, 40
Dongyang
03, 54
| 14 English
HT-E6500W_ZA_0315.indd 14
2012-03-15 오후 4:34:51
Connections
This section describes various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
03
Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit
SPEAKERS OUT
CENTER
FRONT
SUBWOOFER
FRONT
SPEAKER IMPEDANCE : 3
iPod
LAN
WIRELESS
1. Pull the fixing tab of the Toroidal ferrite core to open
it.
2. Double loop the main unit power cord.
3. Attach the Toroidal ferrite core to the main unit power
cord as the figure shows and press it until it clicks.
Connections
If you attach a Toroidal ferrite core to the power cord of
the main unit, it will help to prevent RF interference from
radio signals.
Connecting the Speakers
Position of the product
Place it on a stand or cabinet shelf, or
under the TV stand.
Center
Subwoofer
Product
Front (R)
Selecting the Listening Position
Surround (R)
Front (L)
Surround (L)
The listening position should be
located about 2.5 to 3 times the
TV's screen size away from the TV.
For example, if you have a 46 inch
screen, locate the listening position
115 to 138 inches (9.6 to11.5 feet)
from the screen.
Wireless
Receiver Module
Front
Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward
you. Place the front speakers so that their tweeters will be at the same height as your
ear. Align the front face of the front speakers with the front face of the center speaker or
place them slightly in front of the center speakers.
Center Speaker
It is best to install the Center Speaker at the same height as the front speakers. You can
also install it directly over or under the TV.
Surround
Speakers
Subwoofer
Place these speakers to the side of your listening position. If there isn't enough room,
place these speakers so they face each other. Position them about 2 to 3 feet (60 to
90cm) above your ear, facing slightly downward.
the front and center speakers, the surround speakers are used mainly for
* Unlike
sound effects. Sound will not come from them all the time.
The position of the subwoofer is not so critical. Place it anywhere you like.
* Surround speakers must be connected to the wireless receiver module.
English
HT-E6500W_ZA_0315.indd 15
15 |
2012-03-15 오후 4:34:53
Connections
Speaker Components
(L)
(R)
(L)
(R)
SURROUND
FRONT
CENTER
SUBWOOFER
SPEAKER CABLE
SWA-5000
Wireless Receiver Module
TX Card
Speaker Cable (2EA)
Connecting The Speakers
1. Match each speaker cable bundle to the correct speaker by matching the
color coded plug on each bundle to the colored sticker on the bottom of
each speaker.
2. To attach speaker wire to each speaker:
a. Press down the red tab on the back of the speaker, insert the red wire,
Black
and then release the tab.
b. Press down the black tab on the back of the speaker, insert the black
wire, and then release the tab.
3. Connect the speaker wire plugs from each speaker to the back of the
product by matching the colors of the speaker plugs to the colors of
the speaker jacks.
4. With the product turned off, insert the TX card into the TX Card
Connection (WIRELESS) on the back of the product.
• Hold the TX card so that the label "WIRELESS" faces upward and
insert the card into the port.
• The TX card enables communication between the product and the
wireless receiver module.
5. Connect the left and right surround speakers to the wireless receiver
module. Again, match the color of the plugs to the jacks on the
wireless receiver module.
TX card
6. Plug the power cord of the wireless receiver module into a wall outlet.
7. Turn on the product. The product and wireless receiver module will
now communicate with each other and you will hear sound from the
Surround speakers.
LAN
Red
WIRELESS
HDMI OUT
| 16 English
HT-E6500W_ZA_0315.indd 16
2012-03-15 오후 4:34:55
Center Speaker
03
Subwoofer
CENTER
FRONT
SUBWOOFER
FRONT
Connections
Front Speaker (L)
SPEAKERS OUT
SPEAKER IMPEDANCE : 3
Front Speaker (R)
SPEAKERS OUT
CENTER
Surround
Speaker (L)
Surround
Speaker (R)
FRONT
SUBWOOFER FRONT
SPEAKER IMPEDANCE : 3
iPod
LAN
WIRELESS
Wireless Receiver Module
This product should be connected with the SWA-5000 only.
| CAUTION |
If you want to install the product on the wall, fasten the screws or nails on the wall firmly and use the holes on the rear of speaker to install.
However, when you install it, accessories (nails or screws) and installation is not provided by the company.
Do not let children play with or near the speakers. They could get hurt if a speaker falls.
When connecting the speaker wires to the speakers, make sure that the polarity (+/–) is correct.
Keep the subwoofer speaker out of reach of children to prevent children from inserting their hands or alien substances into the duct (hole)
of the subwoofer speaker.
Do not hang the subwoofer on the wall using the duct (hole).
Do not insert any other card except the TX card dedicated to the product.
If you insert a different TX card, you can damage the product and may not be able to remove the card easily.
Do not insert the TX card upside down or in the reverse direction.
Insert the TX card when the product is turned off. Inserting the card when it is turned on may cause a problem.
The wireless receiving antenna is built into the wireless receiver module. Keep it away from water and moisture.
For optimal listening performance, make sure that the area around the wireless receiver module location is clear of any obstructions.
If you hear no sound from the wireless surround speakers, switch the mode to Dolby Pro Logic II.
In 2-CH mode, you will hear no sound from the wireless surround speakers.
English
HT-E6500W_ZA_0315.indd 17
17 |
2012-03-15 오후 4:34:59
Connections
| NOTE |
If you place a speaker near your TV set, the screen color may be distorted because of the magnetic field.
Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close to the product, sound
from the speakers may be disrupted because of interference.
If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment or any other device that uses the 2.4/5.8GHz
frequencies near the product, sound from the speakers may be disrupted because of interference.
The maximum transmission distance from the product to the wireless receiver module is about 33 feet (10m), but may vary depending on
your operating environment. If a steel-concrete wall or metallic wall is between the product and the wireless receiver module, the system
may not operate at all, because the radio wave cannot penetrate metal.
If the product doesn't make a wireless connection, you need to run an ID Set between the product and wireless receiver module. With the
product turned off, press "0""1""3""5" on the remote control. Turn on the wireless receiver module. Then, press and hold the “ID
SET” button on the back of the wireless receiver module for 5 seconds, and then turn the product on.
Connecting the FM Antenna
FM Antenna (supplied)
1 . Connect the FM antenna supplied to the FM
ANTENNA Jack.
2 . Slowly move the antenna wire around until
you find a location where reception is good,
then fasten it to a wall or other rigid surface.
AUX
IN
VIDEO
OUT
FM ANT
OPTICAL
HDMI OUT
1
HDMI IN
DIGITAL
AUDIO IN
2
| NOTE |
This product does not receive AM broadcasts.
Connecting to an iPod/iPhone
Using a USB Cable
Using a Dock
Connect an iPod/iPhone using the USB cable to
the front USB port.
To view a video from your iPod on your TV, you must
also connect the Video Out jack on the product to
the Video In jack on your TV. See page 19.
SPEAKERS OUT
AUX
IN
ASC IN
VIDEO
OUT
5V 500mA
CENTER
FRONT
SUBWOOFER
FRONT
SPEAKER IMPEDANCE : 3
FM ANT
OPTICAL
iPod
LAN
WIRELESS
HDMI OUT
1
HDMI IN
2
DIGITAL
AUDIO IN
5V 500mA
iPod
| NOTE |
Make sure to connect the dock connector so that the label “” faces upward.
| 18 English
HT-E6500W_ZA_0315.indd 18
2012-03-15 오후 4:35:01
Connecting to a TV
03
Select either Method 1 or Method 2.
AUX
IN
Connections
• If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote control, and
then select the source the product is connected to (HDMI, Video In, etc.) to view video from the home theater.
VIDEO
OUT
FM ANT
AUX
IN
SPEAKERS OUT
CENTER
FRONT
SUBWOOFER
FRONT
SPEAKER IMPEDANCE : 3
VIDEO
OUT
FM ANT
OPTICAL
iPod
LAN
WIRELESS
HDMI OUT
1
HDMI IN
2
DIGITAL
AUDIO IN
OPTICAL
HDMI OUT
1
HDMI IN
2
DIGITAL
AUDIO IN
(Cable not supplied.)
Method 2
Method 1
HDMI IN
VIDEO IN
Method 1 Connecting to a TV with an HDMI Cable - Best Quality (Recommended)
Connect an HDMI cable (not supplied) from the HDMI OUT jack on the back of the product to the HDMI IN
jack on your TV.
Method 2 Connecting to a TV with a Video Cable - Good Quality
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO IN
jack on your TV.
| NOTE |
The VIDEO Out jack always outputs in the 480i resolution regardless of the resolution set in the Setup menu.
Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by copyright protection systems and
the picture will be distorted on the television.
You can connect the product to your TV using both the HDMI and Video connections.simultaneously.
To view videos from an iPod connected to the product on your TV, you must connect the product to the TV using the Video
connection. If you connect the product to the TV using the Video connection, you can also connect the product to the TV
using the HDMI connection.
English
HT-E6500W_ZA_0315.indd 19
19 |
2012-03-15 오후 4:35:04
Connections
Connecting to External Devices
To select the correct mode for an external device, press the FUNCTION button. Each time you press the button,
the mode changes in this order : BD/DVD D. IN AUX R. IPOD HDMI1 HDMI2 FM
R
W
Red
AUX
IN
White
VIDEO
OUT
FM ANT
SPEAKERS OUT
CENTER
FRONT
SUBWOOFER
FRONT
SPEAKER IMPEDANCE : 3
AUX
IN
VIDEO
OUT
FM ANT
OPTICAL
iPod
LAN
WIRELESS
HDMI OUT
1
HDMI IN
2
OPTICAL
1
DIGITAL
AUDIO IN
HDMI IN
DIGITAL
AUDIO IN
2
(Cable not supplied.)
Method 3
(Cable not supplied.)
Method 2
(Cable not supplied.)
Method 1
External Devices
HDMI OUT
OPTICAL OUT
AUDIO OUT
Method 1 HDMI IN : Connecting to an External Component with an HDMI Cable
Connect an HDMI cable (not supplied) from the HDMI IN jack on the back of the product to the HDMI
OUT jack on your digital device.  Select the HDMI1 or HDMI2 mode.
Method 2 OPTICAL : Connecting an External Digital Audio Component
To connect the digital audio output of digital signal components such as Cable Boxes and Satellite
Receivers (Set-Top-Boxes).
Using a digital optical cable (not supplied), connect the Optical Digital Audio In jack on the product to the
Digital Optical Out jack of the external digital device.
 Select the D. IN mode.
Method 3 AUX IN : Connecting an External Analog Component
Using an RCA audio cable (not supplied), connect the AUDIO In jack on the product to the AUDIO Out
jack on the external analog component.  Select the AUX mode.
• Be sure to match the colors on the cable plugs to the colors on the input and output jacks.
| NOTE |
To see video from your Cable Box/Satellite receiver, you must connect its video output directly to your TV.
This system supports Digital sampling frequencies of 32 kHz or higher from external digital components.
This system supports only DTS and Dolby Digital audio. MPEG audio, a bitstream format, is not supported.
| 20 English
HT-E6500W_ZA_0315.indd 20
2012-03-15 오후 4:35:05
Connecting to a Network Router
Wireless Network
03
Connections
You can connect your product to your network
router using one of the methods illustrated below.
Wired Network
AUX
IN
SPEAKERS OUT
CENTER
FRONT
SUBWOOFER
FRONT
SPEAKER IMPEDANCE : 3
VIDEO
OUT
FM ANT
OPTICAL
iPod
LAN
WIRELESS
HDMI OUT
1
HDMI IN
2
DIGITAL
AUDIO IN
Wireless IP sharer
Broadband modem
(with integrated router)
Broadband
service
Broadband
service
Or
Router
| NOTE |
Broadband
service
Broadband
modem
| NOTE |
Internet access to Samsung’s Software Update server
may not be allowed, depending on the router you use or
your ISP’s policy. For more information, contact your ISP
(Internet Service Provider).
DSL users, please use a router to make a network
connection.
To use the AllShare Play function, you must connect your
PC to your network as shown in the illustrations on the
left.
The connection can be wired or wireless.
If your wireless IP router supports DHCP, this product can
use a DHCP or static IP address to connect to the wireless
network.
Set your wireless IP router to Infrastructure mode. Ad-hoc
mode is not supported.
The product supports only the following wireless security
key protocols:
- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES), WPA2-PSK
(TKIP/AES)
Select a channel on the wireless IP router that is not
currently being used. If the channel set for the wireless IP
router is currently being used by another device nearby, it
will result in interference and communication failure.
If you select the Pure High-throughput (Greenfield)
802.11n mode and set the Encryption type on your router
or AP to WEP, TKIP or TKIP-AES (WPS2Mixed), the product
will not support a connection in compliance with new WiFi certification specifications.
Wireless LAN, by its nature, may cause interference,
depending on the operating conditions (AP performance,
distance, obstacles, interference by other radio devices,
etc).
English
HT-E6500W_ZA_0315.indd 21
21 |
2012-03-15 오후 4:35:06
Settings
The Initial Settings Procedure
• The Home menu will not appear if you do not configure
the initial settings.
• The OSD (On Screen Display) may change in this
product after you upgrade the software version.
• The access steps may differ depending on the menu
you selected.
1 . Turn on your TV after connecting the product,
and then turn on the product. When you turn
on the product for the first time, the product
automatically displays the Initial Settings
Language screen.
| NOTE |
The product starts the wireless network connection
procedure by default. If you want to set up a wired
connection, select Skip, and then go to "Configuring
Your Network Connection" on page 31 after you have
completed the Initial Settings Procedure.
If you skip wireless network setup here, go to "Wireless
Network" on page 32 to set up the product's wireless
network connection later.
5 . The product searches for and then displays
all available wireless router network
connections.
Initial Settings > Network Settings (2/5)
Initial Settings > On-Screen Language
Select your wireless router from the list:
KIMING_VTOWER
Select a language for the on-screen
displays.
TIAS
▲
Dansk
Nederlands
English
Eesti keel
Suomi
Français
Deutsch
Ελληνικά
Magyar
Italiano
Қазақ
Select English as the
on-screen menu
language.
si-ap
1/4
Refresh
WPS(PBC)
Previous
surlwang5
Next
Next
Add Network
Skip
한국어
▼
2 . Use the ▲▼◄► buttons on the remote
to select the desired language, and then
press the E button twice. The Start screen
appears.
3 . Press the E button to start setup. The
Network Settings screen appears.
6 . Use the ▲▼ buttons to select a router, and
then press the E button. The Next button
is highlighted.
7 . Press the E button to continue. The
Security Key screen appears.
| NOTE |
If you have a WPS(PBC) compatible router, select
WPS(PBC) instead, press the E button, and then follow
the directions on the screen. When done, go to Step 10.
Initial Settings > Network Settings (1/5)
The next step is to set up a wireless network using an
internal LAN Adapter.
Previous
Next
Skip
If you want to connect to your wired network, plug in a
network cable.
4 . Press the E button to set up the product's
wireless network connection or select
Skip, and then press the E button to skip
network setup. If you selected Skip, go to
Step 12.
| 22 English
HT-E6500W_ZA_0315.indd 22
2012-03-15 오후 4:35:10
Initial Settings > Network Settings (4/5)
0 entered
-
WPS PIN
b
c
d
e
f
1
2
3
Previous
g
h
i
j
k
l
4
5
6
Next
m
n
o
p
q
r
7
8
9
s
t
u
v
w
x
y
z
0



A/a

Space
Skip
8 . Enter your network's security key. When
done, use the ▲▼◄► buttons to select
Next, and then press the E button.
| NOTE |
Enter numbers by pressing the number buttons on your
remote.
Enter letters by selecting a letter using the ▲▼◄►
buttons, and then pressing E button.
To display capital letters (or redisplay small letters if
capital letters are displayed), select A/a, and then press
the E button.
To display symbols and punctuation, select , and then
press the E button. To redisplay letters, select , and
then press the E button.
9 . If the connection is successful, the
Connection Complete screen appears. Select
Next, and then press the E button. The
Software Update screen appears.
| NOTE |
If the connection is not successful, select Next, and then
press the E button. After you have completed the Initial
Settings procedure, go to "Wireless Network" on page 32
to set up the product's wireless network connection.
10 . To upgrade the software, select Update
now, and then press the E button. To skip
the upgrade, select Update later, press the
E button, and go to Step 12.
| NOTE |
If you skipped network set up, you must skip Software
Update also.
Initial Settings > TV Aspect Ratio
Set to match the type of television connected.
16:9 Original
16:9 Full
4:3 Letter Box
4:3 Pan-Scan
Previous
Select when connecting to a
16:9 TV Screen. All content
will be displayed at original
aspect ratio. Content
formatted in 4:3 will be
displayed with black bars on
left and right.
Next
12 . Using the ▲▼ buttons, select the aspect ratio
that matches your TV screen, and then press
the E button. Select Next, and then press
the E button.
You have four choices:
16:9 Original - For widescreen TVs. Displays
widescreen pictures in their original 16:9
format and 4:3 pictures (the old, standard
format) in 4:3 pillar box format with black bars
on the left and right.
16:9 Full - For widescreen TVs. Displays
widescreen pictures in their original 16:9
format and expands 4:3 pictures to fill the
16:9 screen.
4:3 Letter Box - For older, standard screen
analog TVs. Displays 4:3 pictures in full
screen and 16:9 pictures in letter box format
that retains the 16:9 aspect ratio but puts
black bars above and below the picture.
4:3 Pan-Scan - For older, standard screen
analog TVs. Displays 4:3 pictures in full
screen and 16:9 pictures in Pan-Scan format
that fills the screen, but cuts off the left and
right sides of the picture and enlarges the
middle vertically.
English
HT-E6500W_ZA_0315.indd 23
Settings
a
04
Enter security key.
11 . If there is a Software Update available,
the product downloads and installs the
upgrade. This can take some time. If there
is no Software Update available, the "There
are no new software updates for you to
download. You already have the most up
to date version." message appears. And
then press the E button. The TV Aspect
Ratio screen appears.
23 |
2012-03-15 오후 4:35:11
Settings
The Home Screen
Initial Settings > Auto Sound Calibration
Connect the calibration microphone
to the ASC IN jack and set up all
speakers correctly as shown before
starting.
Note: Please be aware that this
process outputs a loud test sound
that is needed for proper calibration.
AllShare Play
Previous
Play videos, photos, or music from Disc or connected devices.
Place Calibration Mic.
Here

User
Press Next to set the best speaker
output level.
Press Skip to configure later.
1/4
Next
Skip
3
4
5
2
1
Smart Hub
Disc to Digital
Function
Settings
13 . The Auto Sound Calibration screen appears.
Plug the ASC microphone into the ASC IN
jack on the product.
14 . Press the E button to select the Next
button. Setting the Auto Sound Calibration
function takes about 3 minutes. Select Next,
and then press the E button.
1
Smart Hub. Starts Smart Hub. From Smart Hub,
you can access Netflix, Pandora, YouTube, games,
and other apps.
2
AllShare Play. Play videos, photos or music content
from Disc, USB, PC or mobile devices.
3
Disc to Digital. Upload DVD movies to your
personal Internet Disc to Digital repository. Once
movies are uploaded, they can be streamed to other
devices connected to the Internet.
4
Function. Select the audio/video input source.
5
Settings. Set various functions to suit your personal
preferences.
Initial Settings > Complete
Setup completed.
On-Screen Language

Network Settings

Software Update
-
TV Aspect

Auto sound calibration

Press Smart Hub to
enjoy variety of
Internet content.
OK
Smart Hub
15 . The Setup completed screen appears. Check
the settings to confirm they are correct.
Select OK, and then press the E button.
The Home screen appears.
| NOTE |
If you want to display the Initial Setting screen again and
make changes, select the Reset option. (See page 30)
 Selecting an Option on the Home Screen
1 . To select an option on the Home screen,
move the cursor using the ◄► buttons until it
highlights the option of your choice, and then
press the E button.
If you use an HDMI cable to connect the product to an
Anynet+ (HDMI-CEC)-compliant Samsung TV and 1.) You
have set the Anynet+ (HDMI-CEC) feature to ON in both
the TV and the product and 2.) You have set the TV to a
language supported by the product, the product will select
that language as the preferred language automatically.
| 24 English
HT-E6500W_ZA_0315.indd 24
2012-03-15 오후 4:35:12
Accessing the Settings Screen
4
EXIT Button : Press to exit the current menu.
3D Settings
Display
TV Aspect Ratio
16:9 Original
Smart Hub Screen Size
Audio
BD Wise
Network
System
Support
Size 3
Settings
3
E (Enter) / DIRECTION Button :
~ Press ▲▼◄► to move the cursor or select
an item.
~ Press the E button to activate the currently
selected item or confirm a setting.
04
1 . Select Settings on the Home screen, and
then press E. The Settings screen appears.
Off
Resolution
Auto
Movie Frame (24Fs)
Auto
HDMI Color Format
Auto
HDMI Deep Color
Auto
Progressive Mode
Auto
| NOTE |
The E button on the product's front panel can be
used for same purpose as the E button on the remote
control.
Detailed Function Information
2 . To access the menus, sub-menus, and
options on the Settings screen, please refer
to the remote control illustration below.
| NOTE |
If you leave the product in the stop mode for more than
5 minutes without using it, a screen saver will appear on
your TV. If the product is left in the screen saver mode for
more than 20 minutes, the power will automatically turn
off.
Each Settings function, menu item, and individual
option is explained in detail on-screen. To view an
explanation, use the ▲▼◄► buttons to select the
function, menu item, or option.
The explanation will usually appear on the right of
the screen. A short description of each Settings
function starts on the next page. Additional
information on some of the functions is also in the
Appendix of this manual.
Buttons on the Remote Control Used
for the Settings Menu
VOL
S/W LEVEL
TUNING
/ CH
HOME
REPEAT
1
TOOLS
INFO
RETURN
EXIT
3
2
A
B
TUNER
MEMORY
MO/ST
C
D
4
1
HOME Button : Press to move to the Home screen.
2
RETURN Button : Return to the previous menu.
English
HT-E6500W_ZA_0315.indd 25
25 |
2012-03-15 오후 4:35:17
Settings
Settings Menu Functions
Display
3D Settings
Set up the 3D related functions.
 3D Blu-ray Playback Mode: Select whether to play a Bluray Disc with 3D contents in 3D Mode. If you move to the
Home or Smart Hub Home menu while in 3D mode, the
product will switch to 2D automatically.
 Screen Size: Enter the size of the TV attached to the
product. The product will automatically adjust the 3D output
to the screen size of the TV.
TV Aspect
Ratio
Lets you adjust the output of the product to the screen size of
your TV. See page 23, Step 12 for a description of the screen
size options.
Smart Hub
Screen Size
Lets you select the optimal size for the Smart Hub Screen.
BD Wise
BD Wise is Samsung’s latest inter-connectivity feature.
When you connect a Samsung product and a Samsung TV
with BD Wise to each other via HDMI, and BD Wise is on in
both the product and TV, the product outputs video at the
video resolution and frame rate of the Blu-ray/DVD Disc.
Resolution
Lets you set the output resolution of the HDMI video signal to
Auto, 1080p, 1080i, 720p, 480p. If Composite is connected,
the resolution supports only 480i. The number indicates
the number of lines of video per frame. The i and p indicate
interlaced and progressive scan, respectively. The more lines,
the higher quality.
Movie Frame
(24Fs)
Setting the Movie Frame (24Fs) feature to Auto lets the product
adjust its HDMI output to 24 frames per second automatically
for improved picture quality if attached to a 24Fs compatible
TV.
• You can enjoy the Movie Frame (24Fs) feature only on a TV
supporting this frame rate.
• Movie Frame is only available when the product is in the
HDMI 1080i or 1080p output resolution modes.
HDMI Color
Format
Lets you set the color space format for the HDMI output to match
the capabilities of the connected device (TV, monitor, etc).
HDMI Deep
Color
Lets you set the product to output video from the HDMI OUT
jack with Deep Color. Deep Color provides more accurate
color reproduction with greater color depth.
Progressive
Mode
Lets you improve picture quality when viewing DVDs.
| 26 English
HT-E6500W_ZA_0315.indd 26
2012-03-15 오후 4:35:24
Audio
Speaker
Settings
You can set the speaker options.
04
Equalizer
The product automatically creates a sound field optimized for
your environment. See page 31.
Lets you configure the Equalizer settings manually.
Smart Volume
Lets you set the product so that the volume remains stable
when a scene change occurs or when you change the
channel.
Speaker
Selection
Lets you select which speakers you want active, either the
TV's speakers or the Home theater's speakers.
Audio Return
Channel
Lets you direct the sound from the TV to the Home Theater
speakers. Requires an HDMI connection and an Audio Return
Channel (ARC) compatible TV.
• If Audio Return Channel is set to on and you are using an
HDMI cable to connect the product to the TV, digital optical
input will not work.
• If Audio Return Channel is set to auto and you are using an
HDMI cable to connect the product to the TV, ARC and
digital optical input are selected automatically.
Digital Output
Lets you set the Digital Output to match the capabilities of the
AV receiver you’ve connected to the product. For more details,
please refer to the digital output selection table. (See page 60)
Settings
Auto Sound
Calibration
Lets you apply dynamic range control to Dolby Digital, Dolby
Digital Plus, and Dolby True HD audio.
Dynamic
Range Control
Audio Sync
 Auto: Automatically controls the dynamic range of Dolby
TrueHD audio, based on information in the Dolby TrueHD
soundtrack. Also turns dynamic range control on for Dolby
Digital and Dolby Digital Plus.
 Off: Leaves the dynamic range uncompressed, letting you
hear the original sound.
 On: Turns dynamic range control on for all three Dolby
formats. Quieter sounds are made louder and the volume of
loud sounds is reduced.
When the product is attached to a digital TV, lets you adjust
the audio delay so that the audio syncs with the video. You
can set the delay between 0 and 300 milliseconds.
English
HT-E6500W_ZA_0315.indd 27
27 |
2012-03-15 오후 4:35:25
Settings
Network
Network
Settings
For more information about Network Settings and network
functions, see "Networks and the Internet" starting on page
31.
Network
Status
Lets you check whether a connection to the network and the
Internet have been established.
Wi-Fi Direct
Lets you connect a Wi-Fi Direct device to the product using a
Peer-to-Peer network, without a wireless router. You can use
the device to control the product.
Soft AP
Lets you connect other types of Wi-Fi devices to the product
wirelessly. Requires that you create a security key which
you must enter into the other Wi-Fi devices when you are
connecting them to the network.
AllShare
Settings
Lets you permit external devices such as smart phones to
connect to the product and share content with or control the
product.
Device Name
Lets you assign an identifying name to the product. You use
this name to identify the product when you are connecting
external Wi-Fi devices (smart phones, tablets, etc.) to it.
BD-Live
Settings
Lets you allow, limit, or prohibit an Internet connection for the
BD-Live service.
Disc to Digital
App
Lets you select your default Disc to Digital application after
you have downloaded it. For more information about Disc to
Digital, see page 53.
| NOTE |
Disc to Digital lets you upload DVD movies to your own personal, Internet
Disc to Digital repository and then stream them in HD format to other
Internet connected devices.
| 28 English
HT-E6500W_ZA_0315.indd 28
2012-03-15 오후 4:35:25
System
Initial Settings
Lets you re-run the Initial Settings procedure. See page 22 for
details.
04
Settings
You can connect a wireless USB keyboard or mouse to
the USB port on the front of the product.
 Keyboard Settings: Lets you configure a wireless USB
keyboard connected to the product.
| NOTE |
You can use the keyboard only when a QWERTY keyboard screen or
window appears in the Web Browser.
 Mouse Settings: Lets you configure a wireless USB mouse
connected to the product. You can use the mouse in the
product's menu in the same way you use a mouse on your
PC.
Device
Manager
 To use a mouse with the product's menu:
1 . Connect the USB mouse to the product.
2 . Click the primary button you selected in Mouse Settings.
The Simple Menu appears.
3 . Click the menu options you want.
| NOTE |
Depending on the model of the USB HID keyboard and mouse may not
be compatible with your product.
Some HID keyboard keys may not work.
Wired USB keyboards are not supported.
Some applications may not be supported.
If a wireless HID Keyboard does not operate because of interference,
move the keyboard closer to the product.
Anynet+
(HDMI-CEC
nynet+ is a convenient function that offers linked operations
with other Samsung products that have the Anynet+ feature
and lets you control those products with one Samsung TV
remote. To operate this function, you must connect this
product to an Anynet+ Samsung TV using an HDMI cable.
Language
You can select the language you prefer for the On-Screen
menu, disc menu, subtitles, etc.
• The language you select for the disc menu, disc audio, or
subtitles will only appear if it is supported on the disc.
English
HT-E6500W_ZA_0315.indd 29
29 |
2012-03-15 오후 4:35:26
Settings
The default PIN is 0000. Enter the default PIN to access the
security function if you haven't created your own PIN.
Security
 BD Parental Rating: Prevents playback of Blu-ray Discs
with a rating equal to or above a specific age rating you
enter unless the PIN is entered.
 DVD Parental Rating: Prevents playback of DVDs with a
rating above a specific numerical rating you select unless
the PIN is entered.
 Change PIN: Change the 4-digit PIN used to access
security functions.
 If you forget your PIN
1 . Remove any disc or USB storage device.
2 . Press and hold the 5 button on the front panel for 5
seconds or more.
All settings will revert to the factory settings.
| NOTE |
When the factory default settings are restored, all the user stored BD
data will be deleted.
You can specify the display brightness and time zone.
General
Support
Software Update
Contact
Samsung
Remote
Management
Reset
 Front Display: Lets you change the brightness of the front
panel.
 Time Zone: You can specify the time zone that is applicable
to your area.
 Menu Transparency: Adjust the transparency of the menu
box.
For more information about the Software Update function, see
"Upgrading Software" on page 36.
Provides contact information for assistance with your product.
When activated, lets Samsung Call Center agents diagnose and
fix problems with the product remotely. Requires an active Internet
connection. Remote Management service might not be available in
some countries.
All settings will revert to the default except for the network
and Smart Hub settings. The default security password is 0000.
| 30 English
HT-E6500W_ZA_0315.indd 30
2012-03-15 오후 4:35:26
Auto Sound Calibration
Settings
When you connect this product to a network,
you can use network based applications and
functions such as Smart Hub and BD-LIVE, and
upgrade the product's software through the
network connection. For more information about
accessing and using Internet services, see the
Network Services chapter of this manual on pages
51~54. Instructions for configuring the network
connection start below.
04
By running the Auto Sound Calibration (ASC)
function just once when you relocate or install the
product, you can have the product automatically
recognize the distance between speakers, levels
between channels, and frequency characteristics
to create a 5.1-channel sound field optimized for
your environment.
Networks and the Internet
ASC IN
5V 500mA
Configuring Your Network Connection
ASC
microphone
Auto Sound Calibration Mode
After you have run the Auto Sound Calibration
function, turn on the Auto Sound Calibration Mode
to listen to the calibrated sound.
• Off: Listen to uncalibrated audio.
• On: Listen to calibrated audio, optimized for
your environment.
Running Auto Sound Calibration
To run the Auto Sound Calibration function, follow
these steps:
1 . Plug the ASC microphone into the ASC IN
jack.
2 . Place the ASC microphone at the listening
position.
• Auto Sound Calibration runs automatically
in the following sequence: Front L 
Front R  Center  Surround L 
Surround R  Subwoofer
• To exit the Auto Sound Calibration function,
press the left arrow button (◄ ).
• To cancel the Auto Sound Calibration
Setting, press the RETURN (') button.
Before you begin, contact your ISP to find out
if your IP address is static or dynamic. If it is
dynamic, and you have a wired or wireless
network, we recommend using the Automatic
configuration procedures described below.
If you are connecting to a wired network, connect
the product to your router using a LAN cable
before you start the configuration procedure.
If you are connecting to a wireless network,
disconnect any wired network connection before
you begin.
To begin configuring your network connection,
follow these steps:
1 . In the Home screen, select Settings, and
then press the E button.
2 . Select Network, and then press the E
button.
3 . Select Network Settings, and then press the
E button.
4 . Go to the instructions for Wired networks
starting below or the instructions for Wireless
networks starting on page 32.
Wired Network
Wired – Automatic
After following Steps 1 to 3 above:
1 . Select Start in the Network Settings screen,
and then press the E button. The product
detects the wired connection, verifies the
network connection and then connects to the
network.
English
HT-E6500W_ZA_0315.indd 31
31 |
2012-03-15 오후 4:35:27
Settings
< Getting the Network Settings Values >
Wired - Manual
If you have a static IP address or the Automatic
procedure does not work, you'll need to set the
Network Settings values manually.
You can view your Network Settings values on
most Windows computers. To view the Network
Settings values, follow these steps:
After following Steps 1 to 3 above:
• In Windows XP
1 . Select Start in the Network Settings screen,
and then press the E button. The Network
Status screen appears. The product attempts
to verify the network connection and fails.
1 . Right click the Network icon on the bottom
right of the Windows desktop.
Network Settings
2 . In the pop-up menu, click Status.
3 . On the dialog that appears, click the Support
tab.
4 . On the Support tab, click the Details button.
Wired network connection failed.
MAC Address
IP Address
Subnet Mask
Gateway
DNS Server
5 . The Network settings are displayed.
XX:XX:XX:XX:XX:XX
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Unable to connect to the network. Try the following:
check if your IP address is set correctly in IP Settings.
Contact your Internet Service Provider for more information.
Previous
• In Windows 7
IP Settings
Retry
OK
1 . Click the Network icon on the bottom right of
the Windows desktop.
2 . In the pop-up menu, click Network and
Sharing Center.
2 . Select IP Settings on the right of the screen,
and then press E button.
The IP Settings screen appears.
3 . On the dialog that appears, click the Local
Area Connection or Wireless Network
Connection depending on your network
connection.
3 . Select the IP Mode field, and then set it to
Manual.
4 . On the Support tab, click the Details button.
The Network settings are displayed.
4 . Use the number keypad on your remote to
enter the Network values. Use the ▲▼◄►
buttons on the remote to move from entry
field to entry field.
| NOTE |
| NOTE |
Wireless Network
You can get these values from your Internet provider. You
can also view these values on most Windows computers.
For instructions, see "Getting the Network Settings
Values." on this page.
5 . When done, highlight OK, and then press
E button. The product verifies the network
connection and then connects to the
network.
Depending on your Windows version, the information may
differ.
You can setup a wireless network connection in
three ways:
- Wireless Automatic
- Wireless Manual
- WPS(PBC)
When you configure the wireless network
connection, any wireless network devices currently
connected through the product or, if applicable,
the product's current wired connection, will be
disconnected.
| 32 English
HT-E6500W_ZA_0315.indd 32
2012-03-15 오후 4:35:28
Wireless (General) - Automatic
Network Settings
Select your wireless router from the list:
1/10
iptime23
Refresh
ELT
WPS(PBC)
JSY
Previous
KT_WLAN_C361
Mirhenge_edu
Next
Cancel
SO070VOIP
2 . Select the desired network, and then press
the E button.
3 . Select Next, and then press the E button
again.
4 . On the Security screen, enter your network's
Security Code or Pass Phrase.
Enter numbers directly using the number
buttons on your remote control. Enter letters
by selecting a letter with an arrow button, and
then pressing E button.
5 . When done, select Next at the right of the
screen. The product verifies the network
connection and then connects to the
network.
| NOTE |
You should be able to find the Security Code or Pass
Phrase on one of the set up screens you used to set up
your router or modem.
Wireless (General) - Manual
If you have a static IP address or the Automatic
procedure does not work, you'll need to set the
Network Settings values manually.
After folloiwng Steps 1 to 3 in "Configuring Your
Network Connection" on page 31:
• Enter numbers directly using the number
buttons on your remote control.
• Enter letters by selecting a letter with the
▲▼◄► buttons, and then pressing the
E button.
• To display capital letters (or redisplay small
letters if capital letters are displayed), select
A/a, and then press the E button.
• To display symbols and punctuation, select
, and then press the E button. To
redisplay letters, select , and then press
the E button.
When done, select Next, and then press the
E button.
6 . Select the Security Type, select Next, and
then press the E button.
7 . On the Security screen, enter your network's
Security Code or Pass Phrase.
• Enter numbers directly using the number
buttons on your remote control.
• Enter letters by selecting a letter with the
▲▼◄► buttons, and then pressing the
E button.
8 . When done, select Next at the right of the
screen, and then press the E button.
9 . The Network Status screen appears.
The product attempts to verify the network
connection and fails.
10 . Select IP Settings on the right of the screen,
and press the E button. The IP Settings
screen appears.
English
HT-E6500W_ZA_0315.indd 33
Settings
1 . Select Start in the Network Settings screen,
and then press the E button.
The product searches for and then displays a
list of the available networks.
04
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 31:
1 . Select Start in the Network Settings screen,
and then press the E button. The product
searches for and then displays a list of the
available networks.
2 . Select the desired network or Add Network,
and then press the E button.
3 . Select Next, and then press the E button
again.
4 . If you selected a network in Step 2, go to
Step 7. If you selected Add Network, go to
Step 5.
5 . Enter your wireless network or wireless
router's name.
33 |
2012-03-15 오후 4:35:29
Settings
11 . Select the IP Mode field, and then set it to
Manual.
12 . Use the number keypad on your remote to
enter the Network values. Use the ▲▼◄►
buttons on the remote to move from entry
field to entry field.
| NOTE |
You can get these values from your Internet provider. You
can also view these values on most Windows computers.
For instructions, see "Getting the Network Settings
Values." on page 32.
13 . When done, highlight OK, and then press E
button. The Network Status screen appears.
The product verifies the network connection
and then connects to the network. When it
is done, highlight OK, and then press E
button.
Wi-Fi Direct
The Wi-Fi Direct function allows you to connect
Wi-Fi Direct devices to the product and each other
using a peer-to-peer network, without a wireless
router.
1 . Turn on the Wi-Fi direct device and activate
its Wi-Fi Direct function.
2 . In the Home screen, select Settings, and
then press the E button.
3 . Select Network, and then press the E
button.
4 . Select Wi-Fi Direct, and then press the E
button.
The Wi-Fi Direct devices that you can
connect appear.
Wi-Fi Direct
Device
Name : [HTS]E6500W
Display
Select your Wi-Fi Direct device to connect to.
WPS(PBC)
One of the easiest ways to set up the wireless
network connection is using the WPS(PBC)
function. If your wireless router has a WPS(PBC)
button, follow these steps:
After following Steps 1 to 3 in "Configuring Your
Network Connection" on page 31:
1 . Select Start in the Network Settings screen,
and then press the E button.
AndroidXXXXXXX
Disconnected
Network
Refresh
System
Close
Support
m Move
" Enter ' Return
5 . You have three ways to complete the Wi-Fi
connection:
• Through the Wi-Fi device.
• Through the product using PBC.
• Through the product using a PIN.
Network Settings
Select your wireless router from the list:
Audio
1/10
iptime23
Refresh
ELT
WPS(PBC)
Each is covered below.
JSY
Previous
KT_WLAN_C361
Mirhenge_edu
Next
Through the Wi-Fi Device
Cancel
SO070VOIP
2 . Select WPS(PBC), and then press the E
button.
3 . Press the WPS(PBC) button on your
router within two minutes. Your product
automatically acquires all the network
settings values it needs and connects to your
network.
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
1 . On the Wi-Fi device, follow the devices
procedure for connecting to another Wi-Fi
Direct device. See the device's user manual
for instructions.
2 . When you have completed the procedure,
you should see a pop-up on your TV screen
saying that a device that supports Wi-Fi
Direct has requested to connect. Select OK,
and then press the E button to accept.
3 . The Connecting pop-up appears, followed
by the Connected pop-up. When it closes,
you should see the device listed on the Wi-Fi
Direct screen as connected.
| 34 English
HT-E6500W_ZA_0315.indd 34
2012-03-15 오후 4:35:30
1 . On the Soft AP screen, select Security Key,
and then press the E button. The Security
Key screen appears.
2 . Select PBC, and then press the E button.
The PBC pop-up appears.
2 . On the Security key screen, enter a security
key. Enter numbers directly using the number
buttons on your remote control. Enter
letters by selecting a letter with the ▲▼◄►
buttons, and then pressing the E button.
3 . Press the PBC button on the Wi-Fi Direct
device within 2 minutes.
4 . The Connecting pop-up appears, followed
by the Connected pop-up. When it closes,
you should see the device listed on the Wi-Fi
Direct screen as connected.
Through the Product Using a PIN
1 . Select the Wi-Fi Direct device you want to
connect to this product, and then press the
E button. The PBC/PIN pop up appears.
2 . Select PIN, and then press the E button.
The PIN pop-up appears.
3 . Note the PIN code in the pop-up, and then
enter it into the appropriate field in the Wi-Fi
Direct device you want to connect.
4 . The Connecting pop-up appears, followed
by the Connected pop-up. When it closes,
you should see the device listed on the Wi-Fi
Direct screen as connected.
3 . When done, use the ▲▼◄► buttons to
move to DONE at the bottom of the screen,
and then press the E button.
When you connect a Wi-Fi device through the
connection procedure on the device, you must
enter the security key you created here into the
appropriate field.
AllShare Settings
The AllShare Settings screen lists your network
connected AllShare devices and their IP
addresses. Through this screen, you can allow
a device to access the product, deny access, or
delete the device from the AllShare list.
1 . In the Home screen, select Settings, and
then press the E button.
| NOTE |
2 . Select Network, and then press the E
button.
The wired or wireless network connection will be
disconnected when you use the Wi-Fi Direct function.
3 . Select AllShare Settings, and then press the
E button.
Soft AP
Soft AP lets you connect other Wi-Fi devices to
your network through the product and lets them
access the Internet.
It requires that you create a security key which you
must enter into the other Wi-Fi devices when you
are connecting them to the network.
1 . In the Home screen, select Settings, and
then press the E button.
Settings
< To Set the Soft AP Security Key >
1 . Select the Wi-Fi Direct device you want to
connect to this product, and then press the
E button. The PBC/PIN pop up appears.
04
Through the Product Using PBC
4 . Select a device, and then press the E
button. The AllShare Settings pop-up
appears.
5 . Select Allow, Deny, or Delete from List, and
then press the E button.
The AllShare Settings screen only displays devices
if you have established networked connections
to AllShare devices. For more information about
AllShare networked devices, see pages 38~39.
2 . Select Network, and then press the E
button.
3 . Select Soft AP, and then press the E
button.
4 . Select On or Off, and then press the E
button.
English
HT-E6500W_ZA_0315.indd 35
35 |
2012-03-15 오후 4:35:36
Settings
Upgrading Software
The Software Update menu allows you to
upgrade the product’s software for performance
improvements or additional services.
• Never turn the product off or back on manually during
the update process.
4 . If you select Update now, the product
upgrades the software, turns off, and then
turns on automatically.
5 . If you do not make a selection in one minute
or select Update later, the product stores
the new upgrade software. You can upgrade
the software later using the By downloaded
function.
1 . In the Home menu, select Settings, and then
press the E button.
6 . If you select Don’t update, the product
cancels the upgrade.
2 . Select Support, and then press the E
button.
By USB
3 . Select Software Update, and then press the
E button.
1 . Visit www.samsung.com.
4 . Select one of the following methods:
• Online
3 . Enter the product's model number into the
search field, and then click Find Product.
• By USB
• By Disc
2 . Click SUPPORT on the top right of the page.
4 . Click Get downloads in the center of the
page below the Downloads header.
• By downloaded
5 . Click Firmware in the center of the page.
• Standby Mode Upgrade
6 . Click the ZIP icon in the File column on the
right side of the page.
5 . Press the E button.
Directions for each method begin below.
| NOTE |
The upgrade is complete when the product turns off, and
then turns on again by itself.
Samsung Electronics takes no legal responsibility for product
malfunction caused by an unstable Internet connection or
consumer negligence during a Software Update.
7 . Click OK in the pop-up that appears to
download and save the firmware file to your
PC.
8 . Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
9 . Copy the folder to a USB flash drive.
If you want to cancel the upgrade while the upgrade
software is downloading, press the E button.
10 . Make sure no disc is inserted in the product,
and then insert the USB flash drive into the
USB port of the product.
Online
11 . In the product’s menu, go to Settings >
Support > Software Update.
Your product must be connected to the Internet to
use the Online function.
1 . Select Online, and then press the E button.
The Connecting to Server message appears.
2 . If there is a download available, the Download
pop-up appears with a progress bar and the
download starts.
3 . When the download is complete, the
Upgrade Query window appears with three
choices: Update now, Update later or
Don’t update.
12 . Select By USB.
| NOTE |
There should be no disc in the product when you upgrade
the software using the USB Host jack.
When the Software Update is done, check the software
details in the Software Update menu.
Do not turn off the product during the Software Update. It
may cause the product to malfunction.
Software Updates using the USB Host jack must be
performed with a USB flash memory stick only.
| 36 English
HT-E6500W_ZA_0315.indd 36
2012-03-15 오후 4:35:36
4 . When the update is complete, the product
turns off automatically, and then turns on.
1 . Visit www.samsung.com.
| NOTE |
2 . Click SUPPORT on the top right of the page.
When the system upgrade is done, check the software
details in the Software Update menu.
4 . Click Get downloads in the center of the
page below the Downloads header.
Do not turn off the product during the Software Update. It
may cause the product to malfunction.
5 . Click Firmware in the center of the page.
Standby Mode Upgrade
6 . Click the ZIP icon in the File column on the
right side of the page.
You can set the Standby Mode Upgrade function
so that the product downloads new upgrade
software when it is in Standby mode.
In Standby mode, the product is off, but its
Internet connection is active. This allows
the product to download upgrade software
automatically, when you are not using it.
7 . Click OK in the pop-up that appears to
download and save the firmware file to your
PC.
8 . Unzip the zip archive to your computer. You
should have a single .RUF file.
9 . Write the RUF file onto a disc. We
recommend a CD-R or DVD-R.
10 . Finalize the disc before you remove it from
your computer.
11 . Insert the disc into the product.
12 . In the product’s menu, go to Settings >
Support > Software Update.
13 . Select By Disc.
| NOTE |
When the system upgrade is done, check the software
details in the Software Update menu.
Do not turn off the product during the Software Update.
It may cause the product malfunction.
Media Play
3 . Enter the product's model number into the
search field, and then click Find Product.
05
By Disc
1 . Press the ▲▼ buttons to select Standby
Mode Upgrade, and then press the E
button.
2 . Select On or Off.
If you select On, the product will automatically
download new upgrade software when it
is in Standby mode with the power off. If
it downloads new upgrade software, the
product will ask you if you want to install it
when you turn the product on.
| NOTE |
To use Standby Mode Upgrade function, your product
must be connected to the Internet.
If this function does not appear, you can upgrade to the
latest software and use it.
By downloaded
The By downloaded option lets you upgrade using
a file the product downloaded earlier but you
decided not to install immediately.
1 . If upgrade software has been downloaded,
you will see the software version number to
the right of By downloaded.
2 . Select By downloaded, and then press the
E button.
3 . The product displays a message asking if you
want to upgrade. Select Yes. The product
begins the upgrade.
English
HT-E6500W_ZA_0315.indd 37
37 |
2012-03-15 오후 4:35:37
Media Play
Your Blu-ray product can play Disc and USB
contents and the contents located on your PC,
DLNA compatible mobile phone, or NAS using the
AllShare Play function. For more information about
AllShare Play, refer to page 41.
The AllShare Play Screen
• Use the ◄► buttons to select an item, press
the TOOLS button to display the Tools menu,
select Play, and then press the E button. To
view or play another item, press the RETURN
(') button, and then repeat the process
described in the first sentence.
Playing Video, Photo, or Music Content
To access the AllShare Play screen, select the
AllShare Play icon on the Main screen, and then
press the E button.
1 . Make sure that the source of the content
you want to play or view is connected to or
inserted into the product.
Using the AllShare Play Screen
2 . Use the ▲▼ buttons to select Videos,
Photos, or Music, and then press the E
button. The first source selection on the right
side is highlighted.
AllShare Play / My List /
3 . Use the ▲▼ buttons to select the source of
the content, and then press the E button.
Latest play
My List
Videos
Recently played files will be displayed here.
What's New
Recently Updated 09.Jan.2012
View More
Photos
SAM_0001
SAM_0002
SAM_0003
SAM_0004
Sources displayed for each content type may differ.
SAM_0005
Playlist
Music
| NOTE |
No playlists have been created.
Create a playlist to quickly and easily access your content.
a Login ' Return
4 . To control the playing of Videos, Photos, or
Music, see:
• Controlling Video Playback on page 43.
• Controlling Music Playback on page 45.
When the AllShare Play screen appears, it displays
My List and a list of content types - Videos,
Photos, and Music - on the left side. On the right,
it displays, by default, the content in My List: a
list of recently played or viewed items, a list of the
newest items you have viewed or listened to, and
your most recent Playlist. If you have never played
or viewed any items, or created a Playlist, this area
will be empty.
Playing My List Items
To play displayed My List items, you must have
the source of the items connected to or inserted
in the product. For example, if recently played My
List photos came from a DVD disc, you must have
that disc in the product to view them.
• Playing Photo Contents and Using the Tools
Menu when a File is Highlighted on pages
46~49.
| NOTE |
Depending on how and when you attach a content source
to the product and the content type, the product may
display a different series of screens to start playback.
For alternative playback methods see:
• Playing Files on a USB Storage Device or iPod/iPhone
on page 39.
• Playing Commercial Video Discs on page 40.
• Playing Commercial Audio Discs on page 40.
• Playing a Disc with User Recorded Content on page 41.
To play or view My List items, perform one of the
actions below:
• Use the ◄► buttons to select an item you
want to view or play, and then press the E
button. To view or play another item, press
the RETURN (') button, and then repeat the
process described in the first sentence.
| 38 English
HT-E6500W_ZA_0315.indd 38
2012-03-15 오후 4:35:39
Playing Files on a USB Storage
Device or iPod/iPhone
2 . Turn on the product. When the Main screen
appears, select AllShare Play > Videos,
Photos or Music > Connected Device, and
then press the E button.
4 . Using the ▲▼◄► buttons on your remote,
select the desired contents. To open a folder,
select it, and then press the E button.
To play a file, select it, and then press the E
button.
5 . Press the RETURN (') button to exit a folder
or to return to the Main screen.
Media Play
1 . With the product turned off, connect a USB
storage device or an iPod/iPhone.
05
You can play multimedia files located on a
connected USB device.
3 . The kind of content you selected on the
connected device is displayed. Depending
on how the contents is arranged, you will see
either folders, individual files, or both.
| CAUTION |
AllShare Play
Play videos, photos, or music from Disc or connected devices.
You can only play videos from an iPod when you use the
iPod Dock.
| NOTE |
OR
To prevent possible damage to the USB memory, you
must remove the USB storage device safely using the
“Safely Remove USB” function. Press the HOME button
to move to the Home menu, select the YELLOW (C)
button, and then press the E button.
The Photos menu does not support iPods or iPhones.
1-1. With the product turned on, connect a USB
storage device or an iPod/iPhone.
Only the playback screen will appear on the TV. View other
iPod screens on the iPod player.
2-1. When screen below appears, use the ▲▼
buttons to select the kind of content you
want to view or play, and then press the E
button.
If the connected iPod does not support video playback, the
"Playing video files is not supported on this iPod model."
message appears when you select the Video menu.
Smart Hub
Disc to Digital
Function
Settings
b Disc to Digital FAQs Safely Remove USB
AllShare Play
New device connected.
Play videos,
ss, photos, or music from Disc or connecte
connected
ed devices.
iPod/iPhone Models You Can Use
with This Product
USB DISK
Videos
Photos
Music
" Enter ' Return
Smart Hub
Disc to Digital
Function
Settings
b Disc to Digital FAQs Safely Remove USB
| NOTE |
iPod touch 3rd/2nd/1st generation
iPod classic / iPod with video
iPod with dock connector
iPod with Click Wheel
iPod nano 5th/4th/3rd/2nd generation
iPhone 4S / iPhone 4
iPhone 3GS / iPhone 3G / iPhone
Even though the product will display all available folders,
it will only display files of the content type you selected
in Step 2 or 2-1. For example, if you selected music, you
will only be able to see music files. You can change this
selection using AllShare Play.
English
HT-E6500W_ZA_0315.indd 39
39 |
2012-03-15 오후 4:35:43
Media Play
The Function Screen
On the Function Screen, you can select the audio
and/or video input source to view or listen to.
| NOTE |
You can also change sources by pressing the Function button
in the upper right of the remote.
Playing Commercial Audio Discs
1 . Place a pre-recorded, commercial audio disc
into the disc tray with the disc’s label facing up,
and then close the tray. The AllShare Play Music
screen appears listing the tracks. Playback of
the first track starts automatically.
AllShare Play / Music /
To access the Function Screen, select the
Function icon on the Main screen, and then press
the E button.
Options on the Function Screen
To select, highlight an option using the ▲▼
buttons, and then press the E button.
1 / 17
Audio CD
► TRACK 001
03:59
TRACK 002
04:34
04
34
TRACK 003
04:24
TRACK 004
04:01
TRACK 005
04:26
TRACK 006
05:07
TRACK 007
04:47
TRACK 008
03:59
TRACK 009
04:34
TRACK 010
04:02
‫ ٭‬TRACK 001
00:00 / 03:59
b Page Move / Tools ' Return
Digital In
AUX
Remote iPod
Select to listen to the digital audio
source connected to Digital Audio In.
Select to listen to audio from the
analog audio source connected to
Audio In.
2 . To play a particular track, use the ▲▼ buttons
on the remote to select the track, and then
press the E button.
Music Screen Controls
Select to listen to music or view video
from the iPod connected to the iPod
jack.
Pause a track.
Play a track.
HDMI IN 1
Select to view video from the device
connected to HDMI IN 1.
HDMI IN 2
Select to view video from the device
connected to HDMI IN 2.
Display the Equalizer.
Select to listen to the FM radio.
Adjust the equalizer manually.
(Only when equalizer mode is On)
Tuner
Playing Commercial Video Discs
1 . Place a disc into the disc tray with the disc’s
label facing up and then close the disc tray.
Playback starts automatically.
If playback does not start automatically, press
the 6 button on your remote or select the
AllShare Play option on the Main screen,
and then press the E button. See "Playing
Video, Photo, or Music Content" on page 38.
Repeat one track or all tracks.
Play tracks in random order.
| NOTE |
The Music Screen controls are only accessible when a track
is playing.
All controls do not appear at the same time.
For more information about playing music, go to "Controlling
Music Playback" on page 45.
| 40 English
HT-E6500W_ZA_0315.indd 40
2012-03-15 오후 4:35:52
Playing a Disc with User Recorded
Content
Using the AllShare Network
Function
05
1 . Place a user recorded disc into the disc
tray with the disc’s label facing up, and then
close the tray. The Device Connected pop-up
appears.
2 . Use the ▲▼ buttons to select the type of
content you want to view or play - Videos,
Photos, or Music - and then press the E
button.
| NOTE |
Even though the product will display folders for all content
types, it will only display files of the content type you selected
in Step 2. For example, if you selected music, you will only
be able to see music files. You can change this selection
using AllShare Play.
3 . Use the ▲▼◄► buttons to select the folder
containing the content type you selected in Step
2, and then press the E button.
4 . If you selected Music, the AllShare Play Music
screen appears listing the music files on the
disc. Use the ▲▼ buttons to select the file you
want to play, and then press the E button.
5 . If you selected Photos, the AllShare Play Photos
screen appears listing the photos on the disc.
Use the ▲▼◄► buttons to select the photo you
want to view, and then press the Ebutton.
6 . If you selected Videos, the AllShare Play Videos
screen appears listing the video files on the disc.
Use the ▲▼◄► buttons to select the video you
want to watch, and then press the E button.
| NOTE |
For the Music and Video folders, you can also push the
TOOLS button on your remote, and then select Play Folder to
play or view all the files in the folder automatically. Select the
folder first before pushing the TOOLS button.
AllShare lets you play Videos, Photos, or Music
located on your PC or your DLNA compatible
device through the product using a wireless
network connection.
To Download the AllShare Software
Media Play
You can play multimedia files you have recorded
on DVD or CD discs.
To use AllShare with your PC or DLNA device, you
must install AllShare software on your PC.
You can download the PC software and get
detailed instructions for using AllShare from the
Samsung.com website.
1 . Go to www.samsung.com.
2 . Click Support at the top of the page.
3 . On the Support page, enter the model
number of your product into the Model
Number field.
4 . On the page that appears, click Get
downloads on the left side under Downloads.
The Download Center appears.
5 . On the Download Center page, click the
Software tab.
6 . On the software tab, click the File icon on the
right side of the AllShare line.
7 . In the pop-up that appears, click Save File.
8 . Find the AllShare install file on your disk, and
then double click the file.
9 . In the pop-up that appears, click Run, and
then follow the directions that appear on your
screen.
Download the AllShare Installation/Instruction
manual from the same Software Tab by clicking
the corresponding PDF file symbol in the File
column on the right. The file, in PDF format, will
download and open. You can view and/or save
the file.
For more information about playing music, go to Controlling
Music Playback on page 45.
For more information about playing photo contents, go to
Playing Photo Contents and Using the Tools Menu when a
File is Highlighted on pages 46~49.
For more information about playing video contents, go to
Controlling Video Playback on page 43.
English
HT-E6500W_ZA_0315.indd 41
41 |
2012-03-15 오후 4:35:57
Media Play
Playing Content Located on Your PC or
DLNA Device through the Product
Controlling the Playback of Content
Located on Your PC with Your Smart
Phone
PC
Product
PC
Product
Play back
PC's files
Play back
PC's files
AllShare Connection
1 . Connect the product, your PC, and/or your
DLNA compatible cell phone to the same
wireless network.
2 . Follow the directions in the AllShare software
Installation/Instruction manual to set up
devices and files for playing or viewing.
3 . Select AllShare Play in the product's Home
screen, and then press the E button. The
AllShare Play screen appears.
4 . Select the connected DLNA compatible
device or your PC, and then press the E
button. A screen listing the available files
appears.
5 . Select the file you want to play or view, and
then press the E button.
AllShare
Connection
Control PC's files to
Product
Smart Phone
(Only available with Samsung phones supporting
AllShare functionality.)
1 . Connect the product, your PC, and your
DLNA compatible cell phone to the same
wireless network.
2 . Follow the directions in the AllShare software
Installation/Instruction manual to set up
devices and files for playing or viewing.
3 . On your computer, using the AllShare
software, confirm your phone is connected.
4 . On the phone, select the file you want to view
or play, and then select the Blu-ray product
as the playback device.
5 . On the phone, start playback.
| 42 English
HT-E6500W_ZA_0315.indd 42
2012-03-15 오후 4:35:58
Controlling Video Playback
You can control the playback of video files located on Blu-ray, DVD, and CD discs, and on USB storage
devices. Depending on the disc, some of the functions described in this manual may not be available.
05
Buttons on the Remote Control used for Video Playback
Media Play
DISC MENU
TITLE MENU
0

POPUP
Using the disc menu, title menu, popup
menu and title list
DISC MENU
During playback, press this button to
display the Disc menu.
TITLE MENU
During playback, press this button to
display the Title menu.
• If your disc has a playlist, press the
GREEN (B) button to go to the playlist.
POPUP MENU
During playback, press this button to
display the Pop-up menu.
MUTE
HOME

REPEAT
Repeat Playback
1 . During playback, press the REPEAT
button on the remote control.
2 . Press the ▲▼ buttons to select a
Chapter, All or Title, then press the
E button.
| NOTE |
Repeat a Title The screen may not display Chapter or Title
or Chapter
immediately. Continue to press the ▲▼
buttons until your choice is inside the blue
field.
3 . To return to normal play, press the
REPEAT button again, press the
▲▼ buttons to select Off, and then
press the E button.
1 . During playback, press the REPEAT
button on the remote control.
2 . Press the ▲▼ buttons to select
Repeat A-B.
| NOTE |
Repeat a
Section
The screen may not display Repeat A-B
immediately. Continue to press the ▲▼
buttons until Repeat A-B is inside the blue
field.
3 . Press the E button at the point
where you want repeat play to start (A).
4 . Press the E button at the point
where you want repeat play to stop (B).
5 . To return to normal play, press the
REPEAT button again.
6 . Press the E button.
| NOTE |
DISC MENU or During playback, press this button to
TITLE MENU display the title list.

Playback related buttons
The product does not play sound in Search, Slow,
or Step mode.
6
Starts playback.
5
Stops playback.
7
Pauses playback.
Fast Motion
Play
During playback, press the 3 or button.
Each time you press the 3 or button, the playback speed will change.
Slow Motion
Play
In pause mode, press the button.
Each time you press the button, the
playback speed will change.
Step Motion
Play
In pause mode, press the 7 button.
Each time you press the 7 button, a
new frame appears.
Skip Motion
Play
During playback, press the 1 or 2
button.
Each time you press the 1 or 2
button, the disc moves to the previous or
next chapter or file.
You must set point (B) at least 5 seconds of
playing time after point (A).
English
HT-E6500W_ZA_0315.indd 43
43 |
2012-03-15 오후 4:36:02
Media Play
Using the TOOLS Menu
Menu that appears only when a BD/DVD
During playback, press the TOOLS button.
disc is playing
Title Search
Time Search
Select to move to a desired title if
the disc has more than one title, to a
desired scene, or, using Time Search,
to a specific point in a movie or video.
With Time Search, you designate
the specific point by entering a time
coordinate in the following format
00:00:00 (hours, minutes, seconds)
using the remote.
Repeat Mode
Select to repeat a specific Title, Chapter
(BD/DVD discs only) or marked section.
Works the same as the REPEAT button.
See page 43.
Full Screen
Select to set the desired full screen
size. You can select Original, Mode1
(larger), and Mode2 (largest).
Picture Mode
Select to set the picture mode.
- Dynamic : Choose this setting to
increase sharpness.
- Standard : Choose this setting for
most viewing applications.
- Movie : This is the best setting for
watching movies.
- User : Lets you adjust the sharpness
and noise reduction function
respectively.
| NOTE |
When you select User, the User
Settings screen appears. Select an
option, press E, use the ◄►
buttons to make an adjustment, and
then press E. Press the RETURN
(') button to go back to the TOOLS
menu.
When you use the BD wise function,
this menu will not appear.
Play from the
beginning
Select to play the movie from the
beginning.
Chapter Search
Select to move to a chapter that you
desire to watch.
Audio
Select to set the desired audio
language.
- You can also operate this function
by pressing the AUDIO button on the
remote control.
Subtitle
Select to set the desired subtitle
language.
- You can also operate this function
by pressing the SUBTITLE button on
the remote control.
Angle
To view a scene from another angle.
The Angle option displays the number
of angles available to view (1/1, 1/2,
1/3, etc.).
BONUSVIEW
Video /
BONUSVIEW
Audio
Select to set the desired bonusview
option.
Menu that appears only when a file is playing
Go to Videos
List
Move to video list screen.
Scene Search
Search the video file by the scene.
Information
Check the video file's information.
| NOTE |
Depending on the disc or storage device, the Tools menu
may differ. All options may not be displayed.
Equalizer Mode Select to use the Equalizer.
Select to set the Equalizer.
Equalizer
Settings
| NOTE |
It only appears when equalizer
mode is on.
| 44 English
HT-E6500W_ZA_0315.indd 44
2012-03-15 오후 4:36:05
Shuffling Tracks on an Audio CD
Controlling Music Playback
Buttons on the Remote Control used
for Music Playback
1 . During playback, use the ► button to select
in the lower right corner of the screen,
and then press the E button.
6
1
2
3
4
5
6
7
8
DISC MENU
POPUP
5
1
Creating a Playlist
9
TITLE MENU
0
MUTE
4
2 . Use the ▲▼ to set the Shuffle Mode On or
Off, and then press the E button.
1
AllShare Play / Music /
2
3
Fast Play (Audio CD (CD-DA) only)
During playback, press the 3 or button.
Each time you press the 3 or button, the
playback speed will change.
2 7 button : Pause a track.
3 6 button : Plays the currently selected track.
4 5 button : Stops a track.
Skip : During playback, press the 1 or 2 button
5 to move to the previous or next music of listed.
NUMBER buttons : During Playlist playback, press
6 the desired track number. The selected track is
played.
Repeating Tracks on an Audio CD
You can set the product to repeat tracks on an
audio CD (CD-DA/MP3).
1 . During playback, use the ► button to select
in the lower right corner of the screen,
and then press the E button.
2 . Use the ▲▼ to select the repeat mode you
want - Off, One Song, or All - and then
press the E button.
1 / 17
Audio CD
► TRACK 001
03:59
TRACK 002
04:34
04
34
TRACK 003
04:24
TRACK 004
04:01
TRACK 005
04:26
TRACK 006
05:07
TRACK 007
04:47
TRACK 008
03:59
TRACK 009
04:34
TRACK 010
04:02
‫ ٭‬TRACK 001
00:00 / 03:59
b Page Move / Tools ' Return
1 . With the Playback screen displayed, press
the TOOLS button. The Tools menu appears.
2 . Use the ▲▼ buttons to select Selection
Play, and then press the E button. The
Selection Play screen appears.
3 . Use the ▲▼ buttons to select a track, and
then press the E button. A check appears
to the left of the track.
4 . Repeat Step 3 to select and check additional
tracks.
5 . To remove a track from the list, move to the
track, and then press the E button again.
The check on the track is removed.
6 . When done, press the ► button to select
Play, and then press the E button. The
Music Playback screen reappears listing only
the tracks you checked. The selected tracks
play automatically.
| NOTE |
You can create a playlist with up to 99 tracks on Audio
CDs (CD-DA).
If you have created a playlist, Selection Play is replaced
by Edit Playlist on the Tools menu.
On the Selection Play screen, you can also choose Select
All, Deselect All, and Cancel.
English
HT-E6500W_ZA_0315.indd 45
Media Play
You can set the product to play tracks on an audio
CD (CD-DA/MP3) at random.
05
You can control the playback of music content
located on a DVD, CD, or a USB storage device.
45 |
2012-03-15 오후 4:36:06
Media Play
• Use Select All to select all tracks. This cancels
your individual track selections. When you press the
RETURN (') button on your remote or select PLAY and
then press the E button, all tracks will appear on the
Music Playback screen, and the product will begin to
play all tracks from Track 001.
| NOTE |
• Use Deselect All to deselect all selected tracks at once.
Then, select individual tracks or use Select All to select
all the tracks, and then press the RETURN (') button
on your remote or select PLAY and then press the E
button. If you do not use Select All or select individual
tracks, the Playlist will not change.
You can control the playback of photo contents
located on a DVD, CD, or a USB storage device.
• Cancel cancels any changes you made on the Play
Select screen. When you return to the Playback screen,
the Playlist will be unchanged.
Ripping
You can rip music from a music CD to a USB
device inserted in the USB jack.
1 . Insert a USB device into the USB jack on
the front of the product, and then press the
RETURN (') button on your remote.
2 . Insert the disc you want to rip from into the
product and close the disc tray.
3 . With the Playback screen displayed, press
the TOOLS button. The Tools menu appears.
4 . Use the ▲▼ buttons to select Rip, and
then press the E button. The Rip screen
appears.
5 . Use the ▲▼ buttons to select a track, and
then press the E button. A check appears
to the left of the track.
6 . Repeat Step 5 to select and check additional
tracks.
7 . To remove a track from the list, move to the
track, and then press the E button again.
The check on the track is removed.
8 . When done, press the ► button to select
Rip, and then press the E button. The Rip
pop-up appears.
9 . Press the E button to begin the ripping
process. The Ripping Completion Bar pop-up
appears.
10 . When ripping is complete, the “Ripping is
completed.” message appears. Press the
E button.
11 . Press the RETURN (') button to go back to
the Playback screen.
When Ripping is done, a folder called MP is created in the
USB.
Controlling Photo Playback
Using the Tools Menu
During playback, press the TOOLS button.
Go to Photos
List
Select to go to the list of photos on the
current media.
Start Slide
Show
Select to start the slide show.
Slide Show
Speed
Select to set a slide show's speed.
Slide Show
Effect
Select to set a slide show's special
effects.
Background
Music On
Select to listen to music while viewing
a slide show.
Background
Music Setting
Select to set the background music
setting.
Picture Mode
Select to set the picture settings.
- Dynamic : Choose to increase
Sharpness.
- Standard : Choose for most viewing
applications.
- Movie : This is the best setting for
watching movies.
- User : Lets you adjust the sharpness
and noise reduction function
respectively.
| NOTE |
When you use the BD wise function,
this menu will not appear.
Zoom
Select to enlarge the current picture.
(Enlarge up to 4 times)
Rotate
Select to rotate the picture. (This will
rotate the picture either clockwise or
counter clockwise.)
Information
Shows the picture information.
| 46 English
HT-E6500W_ZA_0315.indd 46
2012-03-15 오후 4:36:12
| NOTE |
To enable the background music function, the photo file
must be in the same storage media as the music file.
However, the sound quality can be affected by the bitrate
of the MP3 file, the size of the photo, and the encoding
method.
Monthly
Appears on the View function screen.
Select to sort all photo or video files on
a storage device by the month created.
Selection Play lets you select specific
music, video, and photo files to play.
It works essentially the same for all
media. The example below is for
photos.
You can't enlarge the subtitle and PG graphic in the full
screen mode.
Using the Tools Menu when a File
is Highlighted
1. On the Thumbnail View screen,
highlight a photo, and then press
the TOOLS button on the remote.
When a file is highlighted, press the TOOLS
button.
View
Select to access the sort options: Artist,
Genre, Monthly, Latest Date, etc. The
sort options that appear depend on the
storage and media type.
Folder view
Appears in the View function screen.
Select to display the folders on the
storage device.
Title
Appears on the View function screen.
Select to sort all photo or video files on
a storage device by title.
Artist
Appears on the View function screen.
Select Artist to sort and then display
all music tracks on a storage device by
artist.
Album
Appears on the View function screen.
Select Album to sort and then display
all music tracks on a storage device by
album.
Genre
Appears on the View function screen.
Select Genre to sort and then display
all music tracks on a storage device by
genre.
Latest Date
Appears on the View function screen.
Select to sort and then display all photo
or video files on a storage device from
the latest to earliest date.
2. In the Tools menu, select Selection
Play, and then press the E
button.
3. On the selection screen, use the
▲▼◄► buttons to select a
photo you want to view, and then
press the E button.
A check mark appears to the left
of the picture.
4. Repeat Step 3 for each photo you
want to view.
Selection Play
5. To de-select a photo, highlight it,
and then press the E button.
6. When done, use the ◄► buttons
to select Play, and then press
the E button. A slide show
containing the photos you selected
begins.
7. To pause the slide show, press the
E button once. To restart the
slide show, press the E button
again.
8. To stop the slide show, press the
RETURN (') button.
| NOTE |
After the slide show begins, you can
control the slide show by pressing
the TOOLS button and displaying
the Slide Show menu. See " Using
the Tools Menu" page 46.
English
HT-E6500W_ZA_0315.indd 47
Media Play
Earliest Date
Appears on the View function screen.
Select to sort and then display all photo
or video files on a storage device from
the earliest to latest date.
05
Depending on the disc or storage device, the Tools menu
may differ. All options may not be displayed.
47 |
2012-03-15 오후 4:36:13
Media Play
• Select Create New, and then press
the E button. On the keyboard
pop-up that appears, create a name
for the new playlist. Enter numbers
using the numbers on the remote.
Enter letters by using the ▲▼◄►
buttons to move the cursor, and
then pressing the E button.
When finished, move to DONE at
the bottom of the screen, and then
press the E button.
Select Send to upload selected files
to Picasa, Facebook, Cloud Storage, N
Drive, or Family Story.
To use Send, you need to establish an
account with the on-line site, and then
log in using the Log In function.
1. Use the ▲▼◄► buttons to
select a file, and then press the
E button.
Send
2. Repeat for each track or file you
want to upload.
| NOTE |
You can also move to Select All on
the right, and then press the E
button to select all tracks or files.
Depending on the screen you are
viewing, select Delete to erase a file
Delete (Playlist)
from erasable media (such as a USB
device) or to delete a playlist.
Select Edit Playlist to remove files or
tracks from an existing playlist. The
storage device containing the playlist
must be inserted into or attached to
the product.
3. Select Send on the right side, and
then press the E button.
4. Use the ▲▼ buttons to select the
on line site you want to upload the
files or tracks to, and then press
the E button.
Login / Out
The Log In/Out function lets you log in
to your online Samsung account.
Edit Playlist
Select to create a playlist or add files
or tracks to a playlist.
You can also move to Select All on
the right, and then press the E
button to select all tracks or files.
2. Use the ▲▼◄► buttons to
highlight a track or file, and then
press the E button.
3. Select Remove on the right side,
and then press the E button.
3. Repeat for each track or file you
want to add.
4. Select Add on the right, and then
press the E button.
5. On the screen that appears,
perform one of the following
actions:
• Select the Playlist to which you want
to add the tracks or files and then
press E button.
2. Repeat for each track or file you
want to remove.
| NOTE |
1. Select Add to Playlist, and then
press the E button.
Add to Playlist
1. Use the ▲▼◄► buttons to
select a file, and then press the
E button.
Play Current
Group
After you have sorted by Artist, Genre,
Album,Title, Latest Date, Earliest Date,
or Monthly, select a group that is the
result of the sort (for example, all
pictures taken in August), and then
select Play Current Group to play or
view the files in that group only.
Go to Playlist
Select to go to the Playlist section of
the Main AllShare screen.
| 48 English
HT-E6500W_ZA_0315.indd 48
2012-03-15 오후 4:36:13
Displays media file and content
information.
| NOTE |
Depending on the disc or storage device, the Tools menu
may differ. All options may not be displayed.
Listening to Radio
Using Buttons on the Remote Control
1 . Press the FUNCTION button to select FM.
2 . Tune to the desired station.
• Preset Tuning 1 : Press the 5 button
to select PRESET and then press the
TUNING/CH (,.) button to select the
preset station.
- Before you can tune to preset stations,
you must add preset stations to the
product's memory.
• Manual Tuning : Press the 5 button
to select MANUAL and then press the
TUNING/CH (,.) button to tune to a
lower or higher frequency.
• Automatic Tuning : Press the 5 button
to select MANUAL and then press and
hold the TUNING/CH (,.) button to
automatically search the band.
Example : Presetting FM 89.10 into memory.
1 . Press the FUNCTION button to select FM.
2 . Press the TUNING/CH (,.) button to
select <89.10>.
3 . Press the TUNER MEMORY button.
• NUMBER flashes on the display.
4 . Press the TUNER MEMORY button again.
• Press the TUNER MEMORY button before
NUMBER disappears from the display on its
own.
• After you press the TUNER MEMORY
button, NUMBER disappears from the
display and the station is stored in memory.
5 . To preset another station, repeat steps 2 to 4.
• To tune to a preset station, press the
TUNING/CH (,.) button.
Media Play
Information
Presetting Stations
05
Encoding
Encoding - which changes by language
or by geographical area - modifies
how the product sorts, arranges, and
presents files or tracks, displays dates,
etc. Select Encoding to change the
encoding to match your language or
geographical area.
Using the Special Effects Remote
Control Buttons
SOUND
SOUND EFFECT Function
EFFECT
Lets you select a mode that optimizes the sound.
1. Press the SOUND EFFECT button.
2. Press the ▲▼ button to select the desired mode:
DSP, Dolby Pro Logic II or SFE Mode.
3. Press the ◄► buttons to select the desired sound
effect.
DSP
MP3 Enhancer  Power Bass  Virtual 7.1 Off
Setting Mono/Stereo
Press the MO/ST button.
• Each time the button is pressed, the sound
switches between STEREO and MONO.
• In a poor reception area, select MONO for a
clear, interference-free broadcast.
• MP3 Enhancer : Helps enhance your sound experience
(ex. mp3 music). You can upscale your MP3 level sound
(24 kHz, 8bit) to CD level sound (44.1 kHz, 16bit).
• Power Bass : Increases the volume level of bass tones
and provides thudding sound effects.
• Virtual 7.1 : Applies the 7.1 CH sound effect using the
5.1 CH speaker system.
• Off : Select this for normal listening.
English
HT-E6500W_ZA_0315.indd 49
49 |
2012-03-15 오후 4:36:14
Media Play
Dolby Pro Logic II
Movie  Music  Game  Matrix  Prologic  Off
Playing a 2D video in 3D mode
• Movie : Adds realism to a movie soundtrack.
• Music : When listening to music, you can experience
sound effects as if you are listening to the actual
performance.
• Game : Enhances the excitement of the game’s sound.
• Matrix : Select to hear multi channel surround sound.
• Prologic : Select to listen to a 2CH sound source in
5.1CH surround sound with all speakers active.
- A specific speaker(s) may not output depending on
the input signal.
• Off : Select this for normal listening.
You can enjoy an ordinary 2D video in 3D mode.
| NOTE |
If you move to the Home or Smart Hub Home menu
when the product is in 3D mode, it will switch to 2D
automatically.
SFE Mode
Symphony Hall in Boston (Hall 1)  Philharmonic
Hall in Bratislava (Hall 2)  Jazz Club in Seoul B 
Church in Seoul  Amphitheater (Rock)  Off
• Symphony Hall in Boston (Hall 1) : Provides a clear
vocal as if listening in a concert hall.
• Philharmonic Hall in Bratislava (Hall 2) : Also
provides a clear vocal as if listening in a concert hall
but, less powerful than HALL1.
• Jazz Club in Seoul B : Recommended setting for Jazz.
• Church in Seoul : Gives the feel of being in a grand
church.
• Amphitheater (Rock) : Recommended setting for
Rock.
• Off : Select this for normal listening.
3D Sound
You can enjoy more natural and vivid surround sound
with enriched tones by adjusting the depth of sound
using the level options.
Off  High  Medium  Low
| NOTE |
3D Sound is not available in FM mode.
| 50 English
HT-E6500W_ZA_0315.indd 50
2012-03-15 오후 4:36:14
Network Services
Smart Hub at a Glance
1
34
Network Services
To use network services, you must first:
2
06
You can enjoy various network services such as
Smart Hub or BD-LIVE by connecting the product
to your network.
Search
1 . Connect the product to the network.
(See page 21)
2 . Configure the network settings.
(See pages 31~35)
0
9
Samsung Apps
Your Video
Family Story
Fitness
Kids
5
6
Contents 1
Contents 2
Contents 3
Contents 4
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
7
Using Smart Hub
Using Smart Hub, you can download movies,
videos, and music from the Internet, and access
various for pay or free-of-charge applications
and view them on your TV. Application content
includes news, sports, weather forecasts, stock
market quotes, maps, photos, and games.
For instructions that explain how to use Smart
Hub, follow these steps:
a Login b WallPaper / Tools ' Return
1
Your Video : Provides recommendations for videos
based on your tastes.
2
Search : Provides an integrated search of your
video providers and connected AllShare devices.
3
Recommended : Displays recommended contents
managed by Samsung.
4
Commercial : Displays the Smart Hub Guide, an
introduction to the product, and new application
introductions.
5
Family Story : An effortless way to access family
content.
• Provides access to family photos, messages, and
events, anytime and anywhere.
6
Fitness : Gateway to the Unified Self-Care Service.
• Presents fitness videos from various content
partners with feedback on calories burned after
every workout.
7
Kids : Kids service gives kids an easy and safe way
to enjoy their favorite content.
• Provides a wide variety of fun and safe content
for children.
8
Navigation Help : Displays the remote control
buttons you can use to navigate in Smart Hub.
• RED (A) : To log in to Smart Hub.
• GREEN (B) : To display the background screen.
• Tools : To display the settings window.
• Return : To return to the previous menu.
1 . Go to www.samsung.com.
2 . Click Support at the top of the page.
3 . On the Support page, enter the model
number of your product into the Model
Number field.
4 . On the page that appears, click Get
downloads on the left side under Downloads.
The Download Center appears.
5 . On the Download Center page, click the
Manuals tab.
6 . On the Manuals tab, click the file icon to the
right of Smart Hub Users Manual. The manual
downloads.
| NOTE |
The web location of the Smart Hub manual is subject to
change without notice.
English
HT-E6500W_ZA_0315.indd 51
8
51 |
2012-03-15 오후 4:36:15
Network Services
9
My Applications : Displays your personal gallery
of applications which you can add to, modify, and
delete.
0
Samsung Apps : Open Samsung Apps to download
various for pay or free-of-charge application
services.
Web Browser at a Glance
1
http://www.google.com/
Using the Web Browser
You can access the internet using the Web
Browser application which is installed in the Smart
Hub screen by default.
Google Search
b Control Panel Link Browsing / Tools ' Exit
1 . Select Smart Hub on the Home screen, and
then press the E button.
2 . Select the Web Browser application in Smart
Hub, and then press the E button.
| NOTE |
When you run the Web Browser with the product
connected by HDMI to a BD Wise compatible TV - and BD
Wise is on - the browser is maximized to fill the screen
and the TV's resolution is set to the optimal resolution
automatically.
The Web Browser is not compatible with Java
applications.
If you attempt to download a file, and the file can not be
saved, an error message will appear.
The playback of Flash videos is not supported.
E-commerce, for purchasing products online, is not
supported.
ActiveX is not supported.
I’m Feeling Lucky
1
2
Control Panel : Displays the various Web Browser
functions.
•
: Moves to the previous page.
: Moves to the last page before going back.
•
• : Reloads the current page so that it is
refreshed on the screen.
•
: Moves to the Home screen of the Web
Browser.
• : Allows you to zoom in or out of the screen at
various percentages.
•
: Allows you to bookmark specific pages so
that you can move to them easily.
: Allows you to view the history of your visited
•
pages by date, name, or frequency.
http://www.google.com/
•
: Allows you to enter a
page address manually or select a page from the
visited page list to move to that page.
•
: Allows you to switch easily between
multiple, currently open Web Browser windows.
: Allows you to search for information by
•
entering words.
•
: Lets you share the current site with your
family group by sending a message.
•
: Allows you to configure all settings for using
the Web Browser.
| 52 English
HT-E6500W_ZA_0315.indd 52
2012-03-15 오후 4:36:17
Once the product is connected to your network,
you can enjoy various movie-related service
contents available on BD-LIVE compliant discs.
1 . Attach a USB memory stick to the USB jack
on the front of the product, and then check
its remaining memory. The memory device
must have at least 1GB of free space to
accommodate the BD-LIVE services.
2 . Select Settings on the Home screen, and
then press the E button.
3 . Select Network, and then press the E
button.
4 . Select BD-Live Settings, and then press the
E button.
5 . Select BD Data Management, and then
press the E button.
6 . Select Select Device, and then press the
E button.
Disc to Digital lets you upload DVD movies
to your own personal, Internet Disc to Digital
repository and then stream them in HD format to
other Internet connected devices including smart
phones, tablet PCs, and Smart TVs.
To use Disc to Digital, you must first download
the Disc to Digital application. To download the
application, follow these steps.
1 . Make sure the product is connected to the
network. (see pages 31~35)
2 . On the Home screen, select Smart Hub, and
then press the E button.
3 . Select Samsung Apps, and then press the
E button.
4 . In Samsung Apps, select and then download
one of the Disc to Digital applications. There
can be up to three.
5 . Press the HOME button on the remote
control to come back to the Home screen.
6 . Select Settings > Network > Disc to Digital
App, and then select an application to be the
default application for Disc to Digital. (See
page 28)
Disc to Digital App
Select a default application to use for this service.
7 . Select USB, and then press the E button.
Digital Copy
Locker
8 . Insert a Blu-ray Disc that supports BD-LIVE.
Flixster
Fli
i t AApp
9 . Select an item from the list of BD-LIVE service
contents provided by the disc manufacturer.
Network Services
BD-LIVE™
Using Disc to Digital
06
2
Navigation Help : Displays the remote control
buttons you can use to navigate in Web Browser.
• GREEN (B) : To display the Control Panel.
• YELLOW (C) : To search a link.
• Tools : To display Tools window.
• Exit : To return to the previous menu.
Digital Copy
Locker
B
A
Digital Copy
Locker B
Digital Copy
Locker A
Close
' Return
| NOTE |
The way you use BD-LIVE and the provided contents may
differ, depending on the disc manufacturer.
7 . Go to www.flixster.com (or the home site for
Disc to Digital application you downloaded)
and create an account.
English
HT-E6500W_ZA_0315.indd 53
53 |
2012-03-15 오후 4:36:18
Network Services
Registering a DVD Movie in Disc to
Digital
Playing a Registered Disc to Digital
Movie
Before you can stream a DVD movie to other
Internet connected devices, you must register
the movie using your Disc to Digital software and
purchase the right to stream it to other devices.
1 . On a PC or other Internet connected device,
access the Flixster website, and then access
your Flixster account. Enter your account PIN
number as necessary.
1 . Insert the DVD movie you want to register
with Disc to Digital.
2 . Find your movie, and then enter the Activation
Code.
2 . On the Home screen, select Disc to Digital,
and then press the E button.
3 . If you see a play icon, click the play icon.
The movie plays.
3 . Disc to Digital verifies the disc. Once the
DVD's information is verified, the default
application for Disc to Digital opens (in this
example, Flixster).
Section Title Here: Some Title Here
XXXXXXXXXXXXXX
XXXXXX (2010)
AV Rating:
96%
Xxxxxxxx xxx Xxxxxxxxxxxx Xxxxxxxx xx
Xxx xx Xxxxxx Xxxxxxxx
Xxxxxxxx xxx Xxxxxxxx
Xxxxxxx xxx Xxxxxxxxxxxx
Length: XXX xxxxxx Rating: xxxxxx
Genre: Xxx xx Xxxxxx
Synopsis
Movie information
Rent & Own
Cast & Crew
Rent in HD form $x.xx All Cast & Crew Bios
Trailer & Clips
4 Clips
Follow d Share ' Back
| NOTE |
You can also start the Disc to Digital function by pressing
the Disc 2D Digital button on the remote control.
If you don't have a Flixster account, visit "www.flixster.
com" to create your account.
If you've downloaded one or more Disc to Digital
applications, you must set one of them as the default
application.
See "Disc to Digital App" on page 28.
4 . In the Flixster application, find your movie and
then click the Purchase button. The Activation
Code appears.
Disc to Digital only works with commercial DVD-VIDEOs.
Blu-ray Discs, Audio-CD, and Data discs are not
supported.
| NOTE |
Some commercial discs purchased outside of your region
or that do not meet required specifications may not be
supported by this function.
Section Title Here: Some Title Here
XXXXXXXXXXXXXX
XXXXXX (2010)
XXXX
Activate Your Account to Create A Digital Copy
To create a digital copy, you must first activate your account. Go to
www.flixster.com/activate and enter the above code.
Cancel
/ Open Menu
' Back
5 . Record the activation code. You now have
the right to stream your movie in HD quality
resolution to most other Internet connected
devices.
| 54 English
HT-E6500W_ZA_0315.indd 54
2012-03-15 오후 4:36:19
Appendix
Additional Information
07
Note
Connections
• Certain HDMI output resolutions may not work, depending on your TV.
• You must have an HDMI connection to enjoy videos with 3D technology.
• A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Color to Off in the
menu.
Appendix
HDMI OUT
3D Settings
• For some 3D discs, to stop a movie during 3D playback, press the 5 button once. The movie
stops and the 3D mode option is de-activated.
To change a 3D option selection when you are playing a 3D movie, press the 5 button once.
The Blu-ray menu appears. Press the 5 button again, then select 3D Settings in the Blu-ray
menu.
• Depending on the content and the position of the picture on your TV screen, you may see vertical
black bars on the left side, right side, or both sides.
TV Aspect
• Depending on the disc type, some aspect ratios may not be available.
• If you select an aspect ratio and option which is different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
• If you select 16:9 Original, your TV may display 4:3 Pillarbox (black bars on sides of picture).
BD Wise (Samsung Products only)
Settings
• When BD Wise is on, the Resolution setting automatically defaults to BD Wise and BD Wise
appears in the Resolution menu.
• If the product is connected to a device that does not support BD Wise, you can not use the BD
Wise function.
• For proper operation of BD Wise, set the BD Wise option in both the product and the TV to On.
Digital Output
• Be sure to select the correct Digital Output or you will hear no sound or just loud noise.
• If the HDMI device (AV receiver, TV) is not compatible with compressed formats (Dolby digital,
DTS), the audio signal outputs as PCM.
• Regular DVDs do not have BONUSVIEW audio and Navigation Sound Effects.
• Some Blu-ray Discs do not have BONUSVIEW audio and Navigation Sound Effects.
• This Digital Output setup does not affect the analog (L/R) audio or HDMI audio output to your TV.
It affects the optical and HDMI audio output when your product is connected to an AV receiver.
• If you play MPEG audio soundtracks, the audio signal outputs as PCM regardless of your Digital
Output selections (PCM or Bitstream).
BD-LIVE Internet Connection
• The Internet connection may be restricted while you are using BD-LIVE contents.
English
HT-E6500W_ZA_0315.indd 55
55 |
2012-03-15 오후 4:36:23
Appendix
Anynet+ (HDMI-CEC)
• Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user
manual of your TV.
• This function is not available if the HDMI cable does not support CEC.
• If your Samsung TV has an Anynet+ logo, then it supports the Anynet+ function.
BD Data Management
• In the external memory mode, disc playback may be stopped if you disconnect the USB device in
the middle of playback.
• Only those USB devices formatted in the FAT file system (DOS 8.3 volume label) are supported.
We recommend you use USB devices that support USB 2.0 protocol with 4 MB/sec or faster
read/write speed.
• The Resume Play function may not work after you format the storage device.
• The total memory available to BD Data Management may differ, depending on the conditions.
Front Display
• You cannot change the brightness of the
button and the VOL +, - button.
Speaker Settings
Settings
•
•
•
•
When Speaker Selection is set to TV Speaker, audio is produced through the TV speakers.
Running the Auto Sound Calibration function takes about 3 minutes.
Make sure there is no disc in the product when you run the Auto Sound Calibration function.
If the ASC microphone is disconnected during the Auto Sound Calibration setup, the setup will be
canceled.
• When the Auto Sound Calibration function is activated, the DSP, Dolby Pro Logic ll and SFE Mode
will not work.
• If the product is connected to external devices or other components (such as an iPod, AUX,
D. IN), the Auto Sound Calibration Setup may not work properly.
HDMI audio
• When HDMI audio is output to the TV speakers, it is automatically down-mixed to 2 channels.
Audio Return Channel
• When Anynet+ (HDMI-CEC) is Off, the Audio Return Channel function is not available.
• Using an HDMI cable not certified for ARC (Audio Return Channel) may cause a compatibility
problem.
• The ARC function is only available if an ARC-compliant TV is connected.
Digital Output
• Digital Output can be activated when Speaker Selection is set to TV Speaker.
| 56 English
HT-E6500W_ZA_0315.indd 56
2012-03-15 오후 4:36:24
Playing Video files
• The ◄► indicator will not appear on the screen if the BONUSVIEW section does not contain any
BONUSVIEW audio settings.
• The languages available through the Audio Language function depend on the languages that are
encoded on the disc. This function or certain languages may not be available.
• Some Blu-ray Discs may allow you to select either the PCM or Dolby digital audio soundtrack in
English.
Playback
Appendix
Selecting the Audio Language
07
• Video files with high bitrates of 20Mbps or more strain the product’s capabilities and may stop
playing during playback.
Selecting the Subtitle Language
• Depending on the Blu-ray Disc / DVD, you may be able to change the subtitle language in the
Disc Menu. Press the DISC MENU button.
• This function depends on the selection of subtitles that are encoded on the disc and may not be
available on all Blu-ray Discs/DVDs.
• Information about the main feature BONUSVIEW mode will also appear if the Blu-ray Disc has a
BONUSVIEW section.
• This function changes both the primary and secondary subtitles at the same time.
• The total number of primary and secondary subtitles are displayed respectively.
Playing JPEG files
• You can’t enlarge the subtitle and PG graphic in the full screen mode.
Dolby Pro Logic II Mode
• Before selecting Dolby Pro Logic II mode, connect your external device to the AUDIO INPUT jacks
(L and R) on the product. If you connect to only one of the inputs (L or R), you cannot listen to
surround sound.
Using the TOOLS button while playing pictures
AllShare Play
• If the system is connected to a BD Wise compliant TV that has set BD Wise to On, the Picture
Settings menu will not appear.
• The Background Music function will not work unless the music file and the photo file are located
on the same storage media. Also, sound quality can be impacted by the bitrate of the MP3 music
file, the size of the photos, and the encoding method.
Playing back a USB Storage Device
• You must remove the USB storage device safely (by performing the “Safely Remove USB”
function) to prevent possible damage to the USB memory. Press the HOME button to move to the
Home menu, select the YELLOW (C) button, and then press the E button.
English
HT-E6500W_ZA_0315.indd 57
57 |
2012-03-15 오후 4:36:25
Appendix
Playing Music
• Adjust the volume to a moderate level before you connect your iPod to the product.
• When the product is on and you connect an iPod, the product will charge the iPod's battery.
Watching a Movie
AllShare Play
• You must have the VIDEO output (Composite) connected to your TV to view iPod video (See page
19).
• If you want to play iPod video via VIDEO output, set Anynet+ (HDMI-CEC) to off.
• Only the playback screen will appear on the TV. View other iPod screens on the iPod player.
• If you want to return to the iPod menus while the iPod player is connected using the dock, press
FUNCTION on the remote control or press
on the front panel of the system and select
R. IPOD.
The Function mode switches as follows :
BD/DVD  D. IN  AUX  R. IPOD  HDMI1  HDMI2  FM
iPod/iPhone Models You Can Use with This Product
iPod
• The volume control may not operate normally with iPod and iPhone models not listed on page
39. If you have a problem with any of the models listed there, please update the software of the
iPod/iPhone to the lastest version.
• Depending on the software version of the iPod, control problems may occur. This is not a
malfunction of the Home Theater.
• Depending on the software version or the type of iPod, some operations may differ. Install the
latest iPod software. (recommended)
• You can enjoy music or videos through the Blu-ray/DVD disc function and enjoy music, videos
through the Remote iPod function. You need to use the iPod Dock to enjoy videos.
• Playback of applications' contents through the product is not guaranteed. We recommend
playing contents downloaded to the iPod.
• If you have a problem using your iPod, please visit www.apple.com/support/ipod.
| 58 English
HT-E6500W_ZA_0315.indd 58
2012-03-15 오후 4:36:25
Resolution according to the output mode
Blu-ray Disc/E-contents/Digital Contents playback
07
Setup
HDMI/not connected
HDMI Mode
Blu-ray Disc
E-contents/
Digital contents
VIDEO Mode
VIDEO Mode
BD Wise
Resolution of Bluray Disc
1080p@60F
480i
-
Auto
Max. Resolution of
TV input
Max. Resolution of TV
input
480i
-
1080p@60F
1080p@60F
1080p@60F
480i
-
Movie Frame : Auto
(24Fs)
1080p@24F
1080p@24F
480i
-
1080i
1080i
1080i
480i
480i
720p
720p
720p
480i
480i
480p
480p
480p
480i
480i
480i
-
-
-
480i
Appendix
HDMI/connected
Output
DVD playback
HDMI/connected
Output
Setup
HDMI/not connected
HDMI Mode
VIDEO Mode
VIDEO Mode
BD Wise
480i
480i
-
Auto
Max. Resolution of TV input
480i
-
1080p@60F
1080p@60F
480i
-
1080i
1080i
480i
480i
720p
720p
480i
480i
480p
480p
480i
480i
480i
-
-
480i
English
HT-E6500W_ZA_0315.indd 59
59 |
2012-03-15 오후 4:36:26
Appendix
Digital Output Selection
Setup
PCM
Connection
Bitstream
(Re-encoded DTS)
Bitstream
(Re-encoded
Dolby D)
HDMI supported AV receiver
PCM
Up to PCM 7.1ch
PCM
DTS re-encoded
Re-encoded
Dolby Digital *
Dolby Digital
Up to PCM 7.1ch
Dolby Digital
DTS re-encoded
Re-encoded
Dolby Digital *
Dolby Digital
Plus
Up to PCM 7.1ch
Dolby Digital Plus
DTS re-encoded
Re-encoded
Dolby Digital *
Up to PCM 7.1ch
Dolby TrueHD
DTS re-encoded
Re-encoded
Dolby Digital *
Up to PCM 6.1ch
DTS
DTS re-encoded
Re-encoded
Dolby Digital *
DTS-HD High
Resolution
Audio
Up to PCM 7.1ch
DTS-HD High
Resolution Audio
DTS re-encoded
Re-encoded
Dolby Digital *
DTS-HD
Master Audio
Up to PCM 7.1ch
DTS-HD Master Audio
DTS re-encoded
Re-encoded
Dolby Digital *
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
Up to PCM 5.1ch
Dolby Digital
Dolby Digital
Dolby Digital
Up to PCM 6.1ch
DTS
DTS
DTS
Decodes the main feature
audio and BONUSVIEW
audio stream together
into PCM audio and adds
Navigation Sound Effects,
then re-encodes the PCM
audio into DTS bitstream.
Decodes the main
feature audio and
BONUSVIEW audio
stream together into
PCM audio and adds
Navigation Sound
Effects, then reencodes the PCM
audio into Dolby digital
bitstream or PCM.
Audio Stream
Dolby TrueHD
on Blu-ray
Disc
DTS
PCM
Audio Stream
Dolby Digital
on DVD
DTS
Definition for
Blu-ray Disc
Bitstream
(Unprocessed)
Any
Decodes the main
feature audio and
BONUSVIEW audio
stream together into
PCM audio and adds
Navigation Sound
Effects.
Outputs only the main
feature audio stream
so that your AV
receiver can decode
the audio bitstream.
You will not hear
BONUSVIEW audio
or Navigation Sound
Effects.
* If the Source Stream is 2ch or mono, “Re-encoded Dolby D” Setting are not applied. Output will be
PCM 2ch.
Blu-ray Discs may include three audio streams :
- Main Feature Audio : The audio soundtrack of the main feature.
- BONUSVIEW audio : An additional soundtrack such as the director or actor’s commentary.
- Navigation Sound Effects : When you choose some menu navigation, Navigation Sound Effects may
sound. Navigation Sound Effects are different on each Blu-ray Disc.
| 60 English
HT-E6500W_ZA_0315.indd 60
2012-03-15 오후 4:36:27
Troubleshooting
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
The iPod fails to connect.
• Check the condition of the iPod connector and Dock.
• Keep the iPod software version up to date.
Playback does not start.
• Check the region number of the Blu-ray/DVD disc.
Blu-ray/DVD disc purchased from abroad may not be playable.
• CD-ROMs and DVD-ROMs cannot be played on this product.
• Make sure that the rating level is correct.
Playback does not start
immediately when the
Play/Pause button is
pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
• The home theater does not play sound during fast playback, slow playback,and step motion
playback.
• Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
Sound can be heard only
from a few speakers and not
all 6.
•
•
•
•
Dolby Digital 5.1 CH
Surround Sound is not
produced.
• Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital 5.1 CH Surround Sound is
produced only if the disc is recorded with 5.1 channel sound.
• Is the audio language correctly set to Dolby Digital 5.1-CH in the information display?
The remote control does not
work.
• Are you operating the remote within its operational range and within the proper angle relative to
the sensor?
• Are the batteries drained?
• Have you selected the mode (TV/BD) functions of the remote control (TV or BD) correctly?
• The disc is rotating but no
picture is produced.
•
•
•
•
• Picture quality is poor and
the picture is shaking.
Audio language and subtitles
do not work.
On certain Blu-ray/DVD discs, sound is output from the front speakers only.
Check if the speakers are connected properly.
Adjust the volume.
When listening to a CD, radio or TV, sound is output to the front speakers only.
Is the TV power on?
Are the video cables connected properly?
Is the disc dirty or damaged?
A poorly manufactured disc may not be playable.
• Audio language and subtitles will not work if the disc does not contain them.
English
HT-E6500W_ZA_0315.indd 61
Appendix
Symptom
07
Refer to the table below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instructions below do not help, turn off the product, disconnect
the power cord, and contact Samsung Electronics at 1-800-SAMSUNG (1-800-726-7864).
61 |
2012-03-15 오후 4:36:27
Appendix
Symptom
The menu screen does not
appear even when the menu
function is selected.
The aspect ratio cannot be
changed.
• The product is not working.
(Example: The power goes
out or a strange noise is
heard.)
Check/Remedy
• Are you using a disc that does not contain menus?
• You can play 16:9 Blu-ray/DVD discs in 16:9 Full mode, 4:3 Letter Box mode, or
4:3 Pan-Scan mode, but 4:3 Blu-ray/DVD discs are played in 4:3 ratio only. Refer to the
Blu-ray Disc jacket and then select the appropriate function.
• Press and hold the remote control's 5 button for 5 seconds in STANDBY mode.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• The Product is not working
normally.
You have forgotten the rating
level password.
• With no disc in the product, press and hold the product's 5 button for longer than 5
seconds. INIT appears on the display and all settings will return to the default values.
Then, press the POWER button.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio
broadcasts.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an area with
good reception.
While listening to TV audio
through the Product, no
sound is heard.
• If the OPEN/CLOSE ^ button is pressed while listening to TV audio using the D. IN or
AUX functions, the Blu-ray/DVD disc functions are turned on and the TV audio is muted.
"Not Available" appears on
screen.
• The features or action cannot be completed at this time because:
1. The Blu-ray/DVD disc's software restricts it.
2. The Blu-ray/DVD disc's software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
If the HDMI output is set to a
resolution your TV cannot
support (for example, 1080p),
you may not see a picture on
your TV.
• Press and hold the 5 button on front panel for more than 5 seconds with no disc in
the product. All settings will revert to the factory settings.
No HDMI output.
• Check the connection between the TV and the HDMI jack of the product.
• Check if your TV supports 480p/720p/1080i/1080p HDMI input resolution.
Abnormal HDMI output
screen.
• If random noise appears on the screen, it means that TV does not support HDCP (Highbandwidth Digital Content Protection).
| 62 English
HT-E6500W_ZA_0315.indd 62
2012-03-15 오후 4:36:28
Symptom
Check/Remedy
07
AllShare Play function
• AllShare Play shows only files corresponding to the Photo, Music, and Movie categories.
Files that do not correspond to these categories may not be displayed.
Video is played intermittently.
• Check if the network is stable.
• Check if the network cable is properly connected and if the network is not overloaded.
• The wireless connection between the server and the product is unstable.
Check the connection.
The AllShare Play connection
between the TV and PC is
unstable.
• IP address under the same subnetwork should be unique, otherwise IP collision can
results in such a phenomenon.
• Check if you have a firewall enabled.
If so, disable the firewall function.
Appendix
I can see folders shared
through AllShare Play,
but I cannot see the files.
BD-LIVE
I cannot connect to the
BD-LIVE server.
• Test whether the network connection is active by using the Network Status function.
• Check whether a USB memory device is connected to the product.
• The memory device must have at least 1GB of free space to accommodate the BD-LIVE
service.
You can check the available size in BD Data Management. (See page 56)
• See if the BD-LIVE Internet Connection option is set to Allow(All).
• If all above fails, contact the contents provider or update to the latest firmware.
When using the BD-LIVE
service, an error occurs.
• The memory device must have at least 1GB of free space to accommodate the BD-LIVE
service.
You can check the available size in BD Data Management. (See page 56)
| NOTE |
When the factory default settings are restored, all stored user BD data will be deleted.
Repairs
If you contact us to repair your product, an administration fee may be charged if either:
1. An engineer is called out to your home at your request and there is no defect in the product.
2. You bring the unit to a repair center and there is no defect in the product.
We will provide you with the amount of the administration fee before we make a home visit or begin
any work on your product.
We recommend you read this manually thoroughly, search for a solution on line at www.samsung.
com, or contact Samsung Customer Care at 1-800-SAMSUNG (726-7864) before seeking to repair
your product.
English
HT-E6500W_ZA_0315.indd 63
63 |
2012-03-15 오후 4:36:28
Appendix
Specifications
Power Requirements
General
FM Tuner
127.7 W
Weight
8.6 Ibs
Dimensions
16.93 (W) x 2.56 (H) x 12.74 (D) inches
Operating Temperature Range
+41°F to +95°F
Operating Humidity Range
10 % to 75 %
Signal/noise ratio
55 dB
Usable sensitivity
12 dB
Total harmonic distortion
0.5 %
BD (Blu-ray Disc)
Reading Speed : 9.834 m/sec
DVD (Digital Versatile Disc)
Disc
CD : 5 inches (COMPACT DISC)
CD : 3 1/2 inches (COMPACT DISC)
Video Output
Video/Audio
Amplifier
AC 120V, 60Hz
Power Consumption
Composite Video
HDMI
Reading Speed : 6.98 ~ 7.68 m/sec.
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
Blu-ray Disc : 480i
PCM multichannel audio, Bitstream audio, PCM audio
Front speaker output
165W x 2(3Ω)
Center speaker output
170W(3Ω)
Surround speaker output
165W x 2(3Ω)
Subwoofer speaker output
170W(3Ω)
Frequency response
DVD : 480i
1080p, 1080i, 720p, 480p
Analog input
20Hz~20kHz (±3dB)
Digital input
20Hz~40kHz (±4dB)
S/N Ratio
70dB
Channel separation
60dB
Input sensitivity
(AUX)500mV
| 64 English
HT-E6500W_ZA_0315.indd 64
2012-03-15 오후 4:36:29
5.1ch speaker system
Speaker system
Surround
Center
Subwoofer
Impedance
3Ω
3Ω
3Ω
3Ω
Frequency range
140Hz~20kHz
140Hz~20kHz
140Hz~20kHz
40Hz ~ 160Hz
Output sound
pressure level
87dB/W/M
87dB/W/M
87dB/W/M
88dB/W/M
Rated input
165W
165W
170W
170W
Maximum input
330W
330W
340W
340W
Dimensions
(W x H x D)
Front : 3.70 x 11.02 x 2.75 inches
Surround : 3.54 x 5.57 x 2.69 inches
Center : 14.17 x 2.93 x 2.69 inches
Subwoofer : 6.61 x 13.78 x 11.22 inches
Weights
Front : 2.09 Ibs, Surround : 1.34 Ibs
Center : 1.94 Ibs, Subwoofer : 8.09 Ibs
07
Appendix
Speaker
Front
•
•
•
•
Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
Weight and dimensions are approximate.
Design and specifications are subject to change without prior notice.
Dispose unwanted electronics through an approved recycler.
To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877)
278 - 0799
SWA-5000
Power Requirements
AC 120V ~60Hz
Power Consumption
50 W
Weight
2.52 lbs
Dimensions (W x H x D)
3 x 9 x 6 inches
Operating Temperature Range
+41°F to +95°F
Operating Humidity Range
10% ~ 75%
Output
165W x 2 CH
Frequency range
20Hz~20KHz
S/N Ratio
65dB
English
HT-E6500W_ZA_0315.indd 65
65 |
2012-03-15 오후 4:36:29
Rovi Flow-Down License Terms (Terms of Use)
- This application incorporates software and technology of Rovi Corporation (“Rovi”). The Rovi software
and technology (collectively, the “Rovi Technology”) allows End Users to access music-related data
(“Rovi Data”) over the Internet and otherwise from proprietary Rovi databases (the “Rovi Databases”)
located on Rovi servers (the “Rovi Servers”) and to perform other functions. You may access and use
Rovi Data only by means of the intended End User functions of this application software.
- You agree that you will use the Rovi Data, the Rovi Technology, and the Rovi Servers for your own
personal non-commercial use only. You agree not to assign, copy, transfer or transmit the Rovi Data to
any third party. You agree not to use or exploit Rovi Data, the Rovi Technology, the Rovi Databases, or
the Rovi Servers, except as expressly permitted herein.
- You agree that your non-exclusive License to access the Rovi Databases and to use the Rovi Data,
the Rovi Technology, and the Rovi Servers will terminate if you violate these restrictions. If your License
terminates, you agree to cease any and all use of the Rovi Data, the Rovi Technology, and the Rovi
Servers. Rovi reserves all rights in Rovi Data, the Rovi Technology, and Rovi Servers, including all
ownership rights. You agree that Rovi may enforce its rights under this Agreement against you directly
in its own name.
- Rovi reserves the right to delete data from the Rovi Databases or to change data categories for any
cause that Rovi deems sufficient. No warranty is made that the Rovi Technology or Rovi Servers are
error-free or that functioning of Rovi Technology or Rovi Servers will be uninterrupted. Rovi is not
obligated to provide you with any new enhanced or additional data types or categories that Rovi may
choose to provide in the future and is free to discontinue its online services at any time.
- The data you submit to use will not be personal data or personally identifiable data, but rather only
data respecting music albums and associated data that does not appear in the Rovi Lookup Database.
You certify that to the best of its knowledge the album to which the submitted data corresponds is
commercially available and that you End User are lawfully permitted to submit the data.
- To the extent that you, the End User, provide any information or original works of authorship to be
added to Rovi Databases, you represent and warrant that you are the sole author of such work(s) and
further hereby assign to Rovi all rights of copyright therein, including the right to register the copyright
in such work(s) as part of the Rovi Database.
- THE ROVITECHNOLOGY AND EACH ITEM OF ROVI DATA ARE LicenseD TO YOU “AS IS.” ROVI
MAKES NO REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, REGARDING THE
ACCURACY OF ANY ROVI DATA ON THE ROVI SERVERS. ROVI DISCLAIMS ALL WARRANTIES
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE AND NON-INFRINGEMENT.
ROVI DOES NOT WARRANT THE RESULTS THAT WILL BE OBTAINED BY YOUR USE OF THE ROVI
TECHNOLOGY OR ANY ROVI SERVER. IN NO CASE WILL ROVI BE LIABLE TO YOU OR ANY THIRD
PARTY FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES OR FOR ANY LOST PROFITS OR
LOST REVENUES RESULTING FROM YOUR USE OF ROVI DATA, THE ROVI TECHNOLOGY OR
OTHERWISE.
HT-E6500W_ZA_0315.indd 66
2012-03-15 오후 4:36:30
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG and delivered new, in the original carton to the original
consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited
warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United
States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be
presented upon request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the
product to and from the service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts
or products if found to be defective during the limited warranty period specified above. All replaced parts and products become
the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.
SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set
forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an “AS
IS” basis.
Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the
extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following,
including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this
product was not intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect,
fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories,
applications, installations, repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this
product or result in service problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure
to follow operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the
instruction book; product removal or reinstallation; reception problems and distortion related to noise, echo, interference or other
signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH
RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS
LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS
NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
To obtain warranty service, please contact SAMSUNG customer care center.
HT-E6500W_ZA_0315.indd 67
2012-03-15 오후 4:36:30
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
IN THE US
1-800-SAMSUNG
(726-7864)
www.samsung.com
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park,
NJ 07660-2112
AH68-02463A-01
HT-E6500W_ZA_0315.indd 68
2012-03-15 오후 4:36:30