Samsung SCO-2370 User manual

High Resolution 37x
Weatherproof Camera
User Manual
SCO-2370
safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
High Resolution 37x Weatherproof Camera
User Manual
Copyright
©2010 Samsung Techwin Co., Ltd. All rights reserved.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
• Use only the 24V, 60Hz AC adaptor for power supply.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on
the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document
without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers
filled with water on top of the camera. Doing so may cause personal injury due to fire,
electric shock, or falling objects.
English_3
● SAFETY INFORMATION
CAUTION:
safety information
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or
electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way. (SAMSUNG is not liable for problems
caused by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may
cause fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a location
subject to excessive vibration or magnetic interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may
cause undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in
a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (below
-50°F), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so
may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any
time.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
4_ safety information
English_5
● SAFETY INFORMATION
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued use in
such a condition may cause fire or electric shock.
FCC Statement
important safety instructions
contents
1. Read these instructions.
INTRODUCTION
2. Keep these instructions.
8
3. Heed all warnings.
4. Follow all instructions.
Features
What’s included
Component names and functions
13
14
15
16
Connecting to Monitor
Connecting to Power
RS-485 Communication control
Using Coaxial Communications
17
18
Menu Configuration
Menu Setup
38
Troubleshooting
39
41
Specifications
Dimension
42
STW Protocol Command Description
5. Clean only with dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
INSTALLATION & CONNECTION
7. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
13
8. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or the third prong is provided
for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
SETUP
9. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long
periods of time. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
17
TROUBLESHOOTING
38
SPECIFICATIONS
39
STW PROTOCOL COMMAND
DESCRIPTION
42
6_ important safety instructions
English_7
● CONTENTS
8
9
10
introduction
WHAT’S INCLUDED
y 37x Optical Zoom
The built-in SCO-2370 optical zoom lens is a highly durable component. It features auto
focus, auto iris, and zoom functions.
Check if the following items are included in the product package.
y High Resolution
By adopting a diagonal 1/4” 410,000 (NTSC) pixel, 470,000(PAL) pixel SONY CCD, the
camera produces clear picture quality with a horizontal resolution of 600TV lines for color
and a horizontal resolution of 700TV lines for BW mode.
y SSNR3 (Samsung Super Noise Reduction) Function
The high-performance W-V DSP chip effectively removes low-light gain noise and
ghosting to provide clear images even in dark environments.
‫ڋڒ‬
‫ڎڍڈ‬
‫ڪڞڮ‬
SCO-2370
Sunshield
High Resolution 37x
Weatherproof Camera
y DAY&NIGHT(ICR)
This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions.
The COLOR mode operates in daytime conditions to provide optimum colors, and BW
mode operates in night-time conditions to enhance the definition of the image.
y IP68 Approved/Dust and Rain Resistant
With dust and rain resistant design, the camera can be installed outside under building
eaves or places that are exposed to the dust and rain.
L-type hexagon wrenches
(4.0mm)
User Manual
Sunshield Adaptor (1EA)
Tapping Screw (3EA)
SCO-2370
User Guide
y SSDR (Samsung Super Dynamic Range)
For images with high contrast between bright and dark Areas from difficult lighting
conditions such as backlighting, this camera selectively illuminates darker Areas while
retaining the same light level for brighter Areas to even out the overall brightness.
y Communication
RS-485, Coaxial communication methods are supported.
- RS-485 Communications : SAMSUNG-T, SAMSUNG-E, Pelco-P, Pelco-D, Vicon,
Panasonic, Bosch, Honeywell, AD
- Coaxial Communications : Pelco Coaxitron
Installation Video Output Cable
y Temperature control
The built-in heater & fan enables normal operation under a severe condition of -50°C.
y OSD
The camera’s OSD is complimented by 18 foreign languages.
- NTSC : Korean, English, French, Spanish, Japanese, Portuguese, Taiwanese
- PAL : English, French, German, Spanish, Italian, Chinese, Russian, Czech, Polish,
Portuguese, Romanian, Serbian, Swedish, Danish, Turkish
8_ introduction
English_9
● INTRODUCTION
FEATURES
introduction
COMPONENT NAMES AND FUNCTIONS
Back
Front
➋
● INTRODUCTION
❶
➌
➍
‫ڋڒ‬
‫ڎڍ‬
‫ڈڪ‬
➎
‫ڞڮ‬
➏
❶
➊ Camera Sunshield
➋ Sunshield adaptor : Fixing the sunshield onto the camera.
➌ Lens
➍ Video Output Terminal to Monitor : Used for monitoring of video output When
➋
➌
➍
camera installation.
➎ Function Setup Switch : Display the menu on the screen and move the cursor
to four directions to confirm status or after changing a
selected item.
➏ Front cover
➊ Power input terminal : Connect the power as specified for each model here.
➋ MD Output Terminal : Motion detection signals are output through this terminal.
➌ RS-485 control terminal : You can control SETUP MENU through this port by using
external controllers like a Remote controller that RS-485
Communication is supported. For details, see page 15.
➍ Video output terminal : Video signals are output through this port. Connect this port
to the Video IN port of a monitor.
M
Connector
MD
Signal Level
0V
There is no motion
5±0.5sec
← →
I/O
USER Vcc
There is motion
Output
 MD(Motion Detection) Output format is open collector.
10_ introduction
English_11
introduction
installation & connection
COMPONENT NAMES AND FUNCTIONS
CONNECTING TO MONITOR
Please connect the video output terminal located on the back of the camera to the monitor.
Heater & Fan
● INSTALLATION & CONNECTION
This product is equipped with a built-in heater & fan that helps maintaining operational
temperature and humidity.
Monitor
Fan
CCD Camera
Front cover
Heater
y The connection method varies depending on the type of monitor and accessories.Please
refer to the user’s manual for each instrument.
y Please turn off the power when connecting.
1. While powered, the heater & fan operates according to the camera’s internal temperature.
Check heater & fan operation with given internal temperature by referring to the below:
y While the camera is powered, the heater & fan operates if its internal temperature drops
below -10 °C. When the camera’s internal temperature reaches -5 °C, the heater & fan
stops operating.
y While the camera is powered and its internal temperature is between -50 °C ~ -15 °C,
the message “Low Temperature Wait” appears. When it reaches -15 °C, the camera is
initialized and video begins output.
y When the camera’s internal temperature reaches 40 °C, the fan starts operating.
If the camera’s internal temperature reaches 80 °C, it will be initialized.
M
 Be careful not to touch the heater while installing if the ambient temperature is below than -10°C,
since the heater may operate immediately after applying the power.
 If the front cover is cross threaded or not correctly tightened the camera housing will not be weatherproof.
 When you combine the front cover, combine the triangle of front cover and triangle of main body
confront each other.
12_ introduction
English_13
installation & connection
RS-485 COMMUNICATION CONTROL
CONNECTING TO POWER
The recommended adaptor specification for SCO-2370N/P is AC 24V/1.5A over.
Please check the standard power requirement before connecting the power.
Connecting to RS-485 Control Cable
SPEC
WHITE
RS-485+
BLUE
RS-485-
Using RS-485 communication will enable you to control the OSD menu from a
SAMSUNG TECHWIN System Controller or DVR.
(1) Connection to a PC.
Connect the camera to the PC via a RS-485 converter using RS-485 and a serial cable.
EX) SERIAL PORT OF THE PC(COM1) p SERIAL CABLE p RS-485 CONVERTER
p RS-485 CONTROL CABLE
---- Power Input Terminal
(2) Connection to a DVR or System Controller.
Connect the RS-485 cable to the connection ports of the DVR or System Controller.
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size(AWG)
#24(0.22mm²)
#22(0.33mm )
#20(0.52mm )
#18(0.83mm )
Resistance value(Ω/m)
0.078
0.050
0.030
0.018
Voltage drop(V/m)
0.028
0.018
0.011
0.006
2
2
y As shown in the table above, voltage decreases as the wire gets longer.
Therefore having an excessively long distance between the power adaptor and the
camera may affect the camera’s performance.
 There may be some deviation in voltage drop depending on the type of wire and the
manufacturer.
M
M
14_ installation & connection
RS-485 Control Port
(+) CONNECTION TERMINAL
WHITE (TRX+)
(-) CONNECTION TERMINAL
BLUE (TRX-)
* RS-485 Communication establishment initial value
 Standard voltage for camera operation : DC 12V±10% / AC 24V±10%
 Please use a power adaptor that meets the required standards.
 Please connect the power after installation.
485 Control Board Connection Port
2
Item
Camera ID
BAUD RATE
UART MODE
RET PKT
Initial value
1
9600
8-NONE-1
DISABLE
 When making a control system to control the camera, please use to the protocol(SAMSUNG-T,
SAMSUNG-E, PELCO-P, PELCO-D, VICON, PANASONIC, BOSCH, HONEYELL,AD).
 When you connecting to RS-485 CONTROL TERMINAL, please peel off the outer skin inside the
RS-485 CONTROL TERMINAL.
English_15
● INSTALLATION & CONNECTION
CONTROL CABLE
installation & connection
setup
USING COAXIAL COMMUNICATIONS
MENU CONFIGURATION
y Coaxial Communications System
MAIN SETUP MENU
y OSD Control method
DVR
CONTROLLER
SET
MENU/ENTER
OSD KEY
UP
UP KEY
JOYSTICK UP
DOWN
DOWN KEY
JOYSTICK DOWN
LEFT
LEFT KEY
JOYSTICK LEFT
RIGHT
RIGHT KEY
JOYSTICK RIGHT
● OFF
● ON
● ATW
● MANUAL
● OUTDOOR
● INDOOR
BACKLIGHT
● OFF
● BLC
MOTION DET
● OFF
● ON
● MODE
● ZOOM TRACK
● ZOOM SPEED
● D-ZOOM
● ZOOM POS INIT
● USER PRESET
● LENS INIT
● RETURN
● BRIGHTNESS
● IRIS
● SHUTTER
● AGC
● SSNR3
● SENS-UP
● PRIVACY
● DAY/NIGHT
● DIS
● SYNC
● COMM ADJ
● IMAGE ADJ
● MONITOR
● DISPLAY
● RETURN
SSDR
WHITE BAL
FOCUS
DVR
DVD
‫ڪڞڮ‬
‫ڎڍڈ‬
‫ڋڒ‬
EXPOSURE
● SETUP
CAMERA
● AWC ˆ SET
● HLC
● RETURN
: BNC
•
• ---- : RS-485
- Video Cable
The camera’s video output port is connected to the monitor with a BNC coaxial
cable, shown below : If the distance between the camera and the monitor exceeds
the recommended maximum, please use an auxiliary video amp.
M
Distance
Recommended Cable
Specification
300m
3C2V(RG-59/U)
450m
5C2V(RG-6/U)
600m
7C2V(RG-11/U)
SPECIAL
RESET
EXIT
 If the camera is controlled through coaxial communication, please use a video amp intended for
coaxial communications. Regular video amps do not transfer coaxial signals.
16_ installation & connection
English_17
setup
SSDR (Samsung Super Dynamic Range)
MENU SETUP
SSDR illuminates darker spots of an image while retaining the same light level for brighter
spots to even out the overall brightness of images with high contrast between bright and
dark spots.
Use the Function Setup switch within the camera.
Function Setup switch
2. Use the switch to change the SSDR level
according to the contrast between bright and
dark areas.
1. Press the Function Setup switch for 2 seconds. (Short-pressing the Function Setup
Switch activates the AUTO FOCUS).
y Main setup menu is displayed on the monitor screen.
Select the function
using the Function
Setup switch.
MAIN SETUP
君SSDR
WHITE BAL
BACKLIGHT
MOTION DET
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
MAIN SETUP
䯝 SSDR
WHITE BAL
BACKLIGHT
MOTION DET
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
Change the status
using the Function
Setup switch.
SSDR ON
SSDR OFF
White Balance (WHITE BAL)
Use the White Balance function to adjust the screen color.
2. Select the desired feature using the Function Setup switch.
y Each pressing of the Function Setup switch moves the indicator to the next or
previous feature.
y Move the arrow indicator to the desired feature item.
3. Change the status of the selected feature using the Function Setup switch.
4. When completed, move the arrow indicator to ‘EXIT’ and press the Function Setup
switch.
M
18_ setup
 Features marked with a have an accessible submenu.
 An item with the - - - icon is unavailable due to function settings.
1. When the SETUP menu screen is displayed,
select ‘WHITE BAL’ by using the Function
Setup switch so that the arrow indicates
‘WHITE BAL’.
2. Select a desired mode using the Function
Setup switch.
MAIN SETUP
SSDR
䯝 WHITE BAL
BACKLIGHT
MOTION DET
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
English_19
● SETUP
1. When the SETUP menu screen is displayed,
select ‘SSDR’ by using the Function Setup
switch so that the arrow indicates ‘SSDR’.
setup
M
 White Balance may not work properly under the following conditions. In this case select the AWC
mode.
➊ When the color temperature of the environment surrounding the subject is out of the control
range (e.g. clear sky or sunset).
➋ When the ambient illumination of the subject is dim.
➌ If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become unstable.
BACKLIGHT
Unlike conventional cameras, the SCO-2370 is designed to deliver a distinctive subject
and background at the same time, even when the subject is backlight, by using the
features of the proprietary W-V DSP chip.
1. When the SETUP menu screen is displayed,
select ‘BACKLIGHT’ by using the Function
Setup switch so that the arrow indicates
‘BACKLIGHT’.
20_ setup
MAIN SETUP
SSDR
WHITE BAL
䯝 BACKLIGHT
MOTION DET
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
2. Select a desired mode using the Function Setup switch depending on the camera
purpose.
y OFF : Not being used
y BLC : Enables a user to directly select a
desired area from a picture, and to view
the area more clearly.
y HLC (HIGH LIGHT COMPENSATION) :
If the scene contains extremely bright light
areas such as; from car headlight, the
light can mask out much of the on-screen
detail.
- LEVEL : Adjust level of the HLC function.
(LOW,MIDDLE,HIGH)
- MASK TONE : Change the brightness
BLC SETUP
䯝LEVEL
LOW
TOP
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
30
BOTTOM
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
75
LEFT
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
30
RIGHT
RETURN
IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
70
3. Select a desired mode using the Function Setup switch and press the Function Setup
switch.
y Select ‘BLC’ to adjust the area to be enhanced then adjust the level.
M
 Since the following symptoms may occur according to the ambient illumination when BLC is
selected, set it to OFF.
➊ Color or screen changes unnaturally.
➋ Noise appears in the bright part of the screen.
 Since the performance of the BLC function may be affected by the area of the bright part of the
screen, optimize the installation angle for the best BLC performance.
 If you increase LIMIT, the screen display may be distorted.
 For high performance of BLC function, We recommend that you set IRIS to AUTO in the
EXPOSURE setup.
 Activating BLC may cause the camera to repeat the Auto Focus operation depending on lighting
conditions. It is recommended that you use the Focus Setup menu in One-Push or Manual
mode.
 Smart Zoom and BLC cannot be used in conjunction with each other:
 Setting up Smart Zoom and then BLC automatically cancels Smart Zoom.
English_21
● SETUP
y Select one of the following 5 modes, as appropriate for your purpose.
- ATW : Select this when the color temperature is between 1,800˚K and 10,500˚K.
- MANUAL : Select this to fine-tune White Balance manually. Set White Balance
first by using the ATW or AWC mode. After that switch to MANUAL
mode, fine-tune the White Balance and then press the Function
Setup switch.
- AWC€SET : To find the optimal luminance level for the current environment,
point the camera towards a sheet of white paper and press the
Function Setup switch. If the environment changes, readjust it.
- OUTDOOR : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)
- INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
setup
y HLC : Enable the user to change the level,
mask tone area.
MOTION DETECTION
HLC SETUP
䯝LEVEL
MASK TONE
MIDDLE
IIIIIIIIIIIIIIIIIIIIÂIIIIIIIIIIIIIIIIIIIII
7
1. When the SETUP menu screen is displayed,
select ‘MOTION DETECTION’ by using the
Function Setup switch so that the arrow
indicates ‘MOTION DETECTION’.
M
 For effective viewing of license plates, there is a minimum required illumination and the shutter
speed needs to be faster than 1/200sec.
 Because there can be a difference in the effectiveness of HLC according to the amount of light
area in the screen, optimize the installation angle for the best HLC performance.
 When dark, the HLC is only activated when a bright light exceeding a specific size. (In NIGHT
ONLY mode.)
 The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY mode.)
 The HLC is not activated when the D-ZOOM mode is ‘ON’ or DIS mode is ‘ON’.
22_ setup
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
䯝 MOTION DET
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
y OFF : MOTION DETECTION mode is cancelled.
y ON : Any motion in the selected areas is observed.
- AREA SEL : You can select the area
MD SETUP
you wish to observe from
the 8 area.
AREA 1
䯝AREA SEL
AREA MODE
ON
- AREA MODE : Determines whether
LOW
SENSITIVITY
to use the MD area
OFF
SMART ZOOM
selected in SENSITIVITY
RETURN
- SENSITIVITY : You can select low
or high level. When
SENSITIVITY is high,
motion detection
sensitivity is increased to recognize even small movement
- SMART ZOOM : Smart zoom is operated in connection with MOTION
DETECTION. When the SMART ZOOM function is ‘ON’ while
the MOTION DETECTION mode is ‘ON’, the zoom goes to
the TARGET ZOOM position once motion is detected. Once
the zoom action is finished and ‘DWELL TIME’ has passed,
the zoom returns to the ‘SMART ZOOM’ position.
English_23
● SETUP
RETURN
This product has a feature that will detect movements of objects in 8 different areas on
the screen. The camera detects an object’s movement by sensing disparity of outline,
brightness levels and color. The camera sends a detection signal out via the MD output
terminal and will zoom into a pre-determined point.
setup
y START ZOOM : By moving the Function
Setup switch in the ‘SMART ZOOM’ item
to select the zoom position from 1x to 37x
to be returned after the ‘SMART ZOOM’
action is over.
SMART ZOOM SETUP
X1
X5
5 SEC
y DWELL TIME : Use the Function Setup
switch in the ‘DWELL TIME’ item to select a time between 5 and 60 seconds
for the dwell time before the zoom is returned to the ‘SMART ZOOM’ position.
(5,7,10,15,20,30,40,60 sec)
M




Tips on Using the Motion Detection Feature
The feature may not function properly under flickering light conditions.
The camera interprets sudden changes in lighting and subsequent change in brightness of an
object as motion.
With the feature enabled, other algorithms may require additional time to operate.
This system does not guarantee prevention of fire or theft. The manufacturer shall not be held responsible
for any accident or damage incurred.
FOCUS
1. Press the Function Setup switch to access the main setup menu and then position
the indicator over FOCUS using the Function Setup switch.
2. Press the Function Setup switch.
y MODE : You can select the most suitable zoom mode. Move the arrow indicator
to ’MODE‘ using Function Setup switch.
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
MOTION DET
䯝 FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
24_ setup
FOCUS SETUP
ON
ATW
OFF
OFF
䯝 MODE
ZOOM TRACK
ZOOM SPEED
D-ZOOM
ZOOM POS INIT
USER PRESET
LENS INIT
RETURN
AUTO
AUTO TRACK
FAST
OFF
OFF
OFF
MANUAL
- ONE PUSH : Focus is automatically adjusted
just once, after zoom position
is changed. Select ‘ONE
PUSH’ and the Function Setup
switch to confirm. Increase or
decrease optical zoom (ZOOM)
or digital zoom (D-ZOOM)
positions using the directional
key of Function Setup Switch
while verifying the changes
on screen. Press the Function
Setup switch once the desired
image quality is obtained.
- MANUAL : Select ‘MANUAL’ and press
the Function Setup switch to
confirm. Increase or decrease
optical zoom (ZOOM) or digital
zoom (D-ZOOM) positions
moving directional key of
Function Setup Switch while
verifying the changes on screen.
Press the Function Setup switch
once desired image quality
is obtained. Focus can be
manually adjusted, independent
of moving zoom.
ZOOM POS SETUP
m : TELE n : WIDE
ZOOM/FOCUS POS SETUP
m : TELE n : WIDE
: NEAR → : FAR
←
ZOOM/FOCUS POS SETUP
m : TELE n : WIDE
: NEAR → : FAR
←
English_25
● SETUP
y TARGET ZOOM : Use the Function Setup
switch in the ‘TARGET ZOOM’ item to
select the zoom position from 1x to 37x to
be used during MOTION DETECTION.
䯝START ZOOM
TARGET ZOOM
DWELL TIME
RETURN
- AUTO : Select AUTO and press the
Function Setup switch to confirm.
Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM)
positions using the Function Setup
switch while verifying the changes
on screen. Enabling D-ZOOM
(ON) means that digital zoom will
activate once optical zoom ends.
The focus automatically adjusts
when the lens zooms in and out.
setup
y ZOOM SPEED : Configure zoom tracing
speed using this feature. Position the
indicator over ‘ZOOM SPEED’ using the
Function Setup switch and then set to
desired mode using the Function Setup
switch.
- FAST : To move zoom fast.
- SLOW : To move zoom slowly.
- MEDIUM : To move zoom at medium speed.
y D-ZOOM : Configure magnification limit
from x2~x16 using this feature. Position
the indicator over ‘D-ZOOM’ using the
Function Setup switch Set ‘D-ZOOM’ to
‘ON’ and press the Function Setup switch
to confirm.
- Set ‘ZOOM LIMIT’ to the desired level
using the Function Setup switch.
FOCUS SETUP
MODE
AUTO
ZOOM TRACK
AUTO TRACK
FAST
䯝 ZOOM SPEED
D-ZOOM
OFF
ZOOM POS INIT
OFF
USER PRESET
OFF
LENS INIT
MANUAL
RETURN
MODE
ZOOM TRACK
ZOOM SPEED
䯝 D-ZOOM
ZOOM POS INIT
USER PRESET
LENS INIT
RETURN
AUTO
AUTO TRACK
FAST
OFF
OFF
OFF
MANUAL
26_ setup
D-ZOOM.
RETURN
X2
FOCUS SETUP
MODE
AUTO
ZOOM TRACK
AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
OFF
䯝 ZOOM POS INIT
USER PRESET
OFF
LENS INIT
MANUAL
RETURN
 The zoom postion is saved after 5 seconds when you set zoom function.
y USER PRESET : Preset user-designated
configurations using this feature. Position
the indicator over ‘USER PRESET’ using
the Function Setup switch and then set
to ‘ON’ using the Function Setup switch.
Press the Function Setup switch to confirm.
FOCUS SETUP
MODE
AUTO
ZOOM TRACK
AUTO TRACK
ZOOM SPEED
FAST
D-ZOOM
OFF
ZOOM POS INIT
OFF
OFF
䯝 USER PRESET
LENS INIT
MANUAL
RETURN
- PRESET NO : Up to 128 preset
configuratons are supported.
- PRESET SAVE : Save configured preset.
- PRESET CLEAR : Clear configured preset.
- RETURN : Revert to the FOCUS SETUP menu.
ZOOM POS SETUP
D-ZOOM LIMIT SETUP
 When the DIS is enabled, you cannot use the
M
FOCUS SETUP
䯝LIMIT
M
y ZOOM POS INIT : Moves to the controlled
ZOOM position when the power is truned on
and the initial ZOOM position has been set.
- AUTO : If you turn the power off and on,
the zoom magnification level is
set to the previous level that was
set before the power went off.
- MANUAL : The zoom magnification level
can be set from 1x to 37X.
m : TELE
X1
n : WIDE
USER PRESET SETUP
ÂIIIIIIIIIIIIIIIIIIIII 3
䯝PRESET NO
PRESET SAVE
PRESET CLEAR
RETURN
PRESET NOT DEFINED
y LENS INIT : Use the Function Setup
LENS INIT SETUP
switch in the ‘Lens initialization’ item select
DAY
1
‘AUTO’ or ‘MANUAL’ and then press the
RETURN
Function Setup switch.
- AUTO : Initialize the lens by setting the
date. Initializing time can be set to 1 ~ 7
days, and the lens is initialized at the specified time interval since the setting.
- MANUAL : The Lens will reset when you press the Function Setup switch.
English_27
● SETUP
y ZOOM TRACK : Select ‘ON’ for the
FOCUS SETUP
‘SMART ZOOM’ item in the MOTION
MODE
AUTO
DETECTION menu and press Function
AUTO TRACK
䯝 ZOOM TRACK
Setup switch to change the settings for the
ZOOM SPEED
FAST
‘SMART ZOOM’ function.
D-ZOOM
OFF
Use the Function Setup switch in the
ZOOM POS INIT
OFF
USER PRESET
OFF
‘ZOOM’ item to select ‘AUTOTRACK’ or
LENS INIT
MANUAL
‘TRACK’ and press Function Setup switch
RETURN
to activate the zoom action focus function.
- AUTO TRACK : Zooming in while
deciding or adjusting the status of the focus.
- TRACK : The camera moves the focus track which is established.
- OFF : Only the zoom lens moves.
setup
EXPOSURE
2. Press the Function Setup switch to confirm.
y BR IGHTNESS : Use this feature to adjust
image brightness. Position the indicator
over ‘BRIGHTNESS’ using the Function
Setup switch. Then increase or decrease
brightness level using the Function Setup
switch while verifying the changes on
screen. Set END once desired level is
obtained.
y IRIS : Set ‘IRIS’ to ‘AUTO’ or ‘MANUAL’.
Position the indicator over ‘IRIS’ using the
Function Setup switch and then select the
desired iris mode using the Function Setup
switch.
- AUTO : The iris is automatically activated
upon illumination.
- MANUAL : Manual iris configuration. Set
‘IRIS’ to ‘MANUAL’ using the
Function Setup switch and
then press the Function Setup
switch. Increase or decrease
iris level using the Function
Setup switch while verifying
the changes on screen.
28_ setup
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
MOTION DET
FOCUS
䯝 EXPOSURE
SPECIAL
RESET
EXIT
ON
ATW
OFF
OFF
EXPOSURE SETUP
䯝 BRIGHTNESS IIIIIIIIIIÂIIIIIIIIIII
50
IRIS
AUTO
SHUTTER
--AGC
HIGH
SSNR3
MEDIUM
SENS-UP
OFF
RETURN
EXPOSURE SETUP
BRIGHTNESS IIIIIIIIIIÂIIIIIIIIIII
50
䯝 IRIS
AUTO
SHUTTER
--AGC
HIGH
SSNR3
MEDIUM
SENS-UP
OFF
RETURN
IRIS MANUAL SETUP
䯝IRIS F-No
RETURN
F1.6
M
 Image may become unstable if the camera is set to ‘ESC’ mode and faces a strong fluorescent light.
 Under ‘ESC’ mode, the brightness can be adjusted using the Function Setup switch.
y AGC (Auto Gain Control) : For brighter images.
➊ Position the indicator over ‘AGC’ using
the Function Setup switch.
➋ Set ‘AGC’ to the desired mode using
the Function Setup switch.
- HIGH : Wide range gain value
adjustment
- MANUAL : Selecting gain value range.
(5dB ~ 41dB)
- OFF : Disabled
- LOW : Narrow range gain value
adjustment
- MEDIUM : MEDIUM range gain value
adjustment
EXPOSURE SETUP
50
BRIGHTNESS IIIIIIIIIIÂIIIIIIIIIII
IRIS
AUTO
SHUTTER
--䯝 AGC
HIGH
SSNR3
MEDIUM
SENS-UP
OFF
RETURN
GAIN MANUAL SETUP
䯝AGC VAL
F1.6
RETURN
English_29
● SETUP
1. Press the Function Setup switch to access
the main setup menu and then position the
indicator over ‘EXPOSURE’ using the Function
Setup switch.
y SHUTTER : Control image brightness by
EXPOSURE SETUP
adjusting shutter speed.
50
BRIGHTNESS IIIIIIIIIIÂIIIIIIIIIII
➊ Position the indicator over ‘SHUTTER’ using
IRIS
AUTO
the Function Setup switch. Then select
䯝 SHUTTER
--the desired shutter mode (A.FLK, ESC,
AGC
HIGH
MANUAL) using the Function Setup switch.
SSNR3
MEDIUM
- MANUAL : Manual shutter speed setting.
SENS-UP
OFF
- A.FLK (NTSC: 1/100, PAL: 1/120) :
RETURN
Flicker-free mode.
- ESC : Automatic shutter speed setting
(optimal).
Auto operation is possible only when
SHUTTER MANUAL SETUP
the IRIS is set to MANUAL.
䯝SHUTTER VAL
1/50
➋ Position the indicator over ‘SHUTTER’
RETURN
using the Function Setup switch. Then
select the desired shutter mode (A.FLK,
ESC, MANUAL) using the Function
Setup switch.
➌ Press the Function Setup switch to complete.
setup
y SSNR3 (Samsung Super Noise Reduction): On screen noise reduction.
SPECIAL
- LOW : Low noise reduction
- MEDIUM : Medium noise reduction
- HIGH : High noise reduction
- OFF : Disabled
2. Press the Function Setup switch to confirm.
M
 Changing the ‘AGC’ setting from LOW to HIGH results in greater sensitivity, as well as on screen noise.
 Setting ‘AGC’ to OFF locks ‘SSNR3’ configuration.
y SENS-UP : This feature ensures clear images
at night or under low light conditions.
➊ Position the indicator over ‘SENS-UP’ using
the Function Setup switch.
SENS-UP LIMIT SETUP
䯝LIMIT
X2
RETURN
➋ Set ‘SENS-UP’ to the desired mode using
the Function Setup switch.
- AUTO : Select this mode for use in night
time or under low light conditions.
- OFF : Disabled
M
➊ When the SPECIAL menu screen is
displayed, using the Function Setup
switch so that the arrow indicates
‘PRIVACY’.
➋ Set up the mode using the 4 direction
buttons..
 Once ‘AUTO’ mode is set, the user can configure the SENS-UP limit by increasing/decreasing
ON
ATW
OFF
OFF
SPECIAL SETUP
䯝 PRIVACY
OFF
DAY/NIGHT
AUTO
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
MONITOR
LCD
DISPLAY
RETURN
the shutter speed (e.g.: X2, X4....... X32, X64, X128, X256, X512).
 The bigger ratio setting brightens darker area, but it may blur image of moving object and the
Auto Focus may not appear to be optimal.
30_ setup
y PRIVACY : Hide an area you want to hide
on the screen.
MAIN SETUP
SSDR
WHITE BAL
BACKLIGHT
MOTION DET
FOCUS
䯝 EXPOSURE
SPECIAL
RESET
EXIT
- AREA SEL : You can select up to 12 areas.
- AREA MODE : Determines whether to use
the area selected in the
AREA SEL.
- MASK COLOR : Determine area color. You
can select Green, Red,
Blue, Black, White, Gray.
PRIVACY SETUP
䯝AREA SEL
AREA MODE
MASK COLOR
IIIIIIIÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
TOP
BOTTOM IIIIIIIIIIIIIÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
ÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
LEFT
IIIIIII
ÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII
RIGHT
RETURN
AREA1
ON
GRAY
39
79
14
53
English_31
● SETUP
1. Press the Function Setup switch to access the
main setup menu and then position the indicator
over ‘EXPOSURE’ using the Function Setup
switch.
setup
y DAY/NIGHT : You can display pictures in
color or black and white.
➋ Select a desired mode using the Function
Setup switch according to the picture
display you want.
# PRIVACY
䯝 DAY/NIGHT
DIS
SYNC
COMM ADJ
IMAGE ADJ
MONITOR
DISPLAY
RETURN
OFF
AUTO
OFF
INT
5 SEC
SLOW
- DWELL TIME : You can select tday/
night switching delay time from.
p 5,7,10,15,20,30,40, 60(sec)
- DURATION : You can select the day/night switching point(lux).
Slow
Color p B/W
B/W p Color
2.6Lux
4.2Lux
1.2Lux
6.0Lux
 When AGC is middle mode.
y EXT : This mode allows you to apply a desired filter to external signals.
M
32_ setup
M
 When DIS is operating, D-ZOOM does not
operate.
LCD
y AUTO : The mode is switched to ‘Color’ in
a normal environment, but switches to
AUTO SETUP
‘B/W’ mode when ambient illumination
is low. To set up the switching time
䯝DWELL TIME
or speed for AUTO mode, press the
DURATION
Function Setup switch.
RETURN
y COLOR : The picture is always
displayed in color.
y B/W : The picture is always displayed in
black and white.
Fast
y DIS : The DIS mode can compensate for
vibration of the camera.
 You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is ‘OFF’.
At this time, the exchange between DAY mode and NIGHT mode operates as like selecting
‘COLOR’ mode.
 The OSD key does not work for 3 seconds when switching to Color or B/W, to ensure stable
camera operation.
 The camera may focus less well under infrared illumination than under normal illumination.
 The brightness of illumination is changeable by installed environment.
SPECIAL SETUP
PRIVACY
OFF
DAY/NIGHT
AUTO
䯝 DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
MONITOR
LCD
DISPLAY
RETURN
y SYNC : Two synchronization modes are available INTERNAL and EXTERNAL
LINE-LOCK.
In LINE-LOCK mode, it synchronizes the camera’s video out signal to the
external SYNC signal.
- INT : Internal synchronization
- LL : External line-lock synchronization
➊ If you choose ‘LL’, you can adjust the desired phase.
Press the Function Setup switch.
➋ You can adjust the desired phase from 0 to 359.
y COMM ADJ (Communication Adjustment) :
This function sets up the camera
communication status when controlling the
camera through an external controlled device.
➊ When the SPECIAL menu screen is
displayed, using the Function Setup
switch so that the arrow indicates
‘COMM ADJ’.
COMMUNICATION SETUP
䯝 PROTOCOL
SAMSUNG-T
ÂIIIIIIIIIIIIIIIIIIIIIIIIIIIII
1
CAM ID
BAUD RATE
UART MODE
RET PKT
9600
8-N-1
DISABLE
RETURN
➋ Set up the mode moving the 4 direction
of the Function Setup switch.
- PROTOCOL : Select the communication PROTOCOL. (SAMSUNG-T/PELCO-D/
PELCO-P/ BOSCH/HONEYWELL/VICON/AD/SAMSUNG-E/PANASONIC)
- CAM ID : Determines the camera's identification number (between 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
English_33
● SETUP
➊ When the SETUP menu screen is
displayed, select ‘DAY/NIGHT’ using the
Function Setup switch so that the arrow
indicates ‘DAY/NIGHT’.
SPECIAL SETUP
setup
- H-REV : You can flip the picture
horizontally on the screen.
CONTROLLER
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
CONTROLLER
‫ڋ‬
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
- SHARPNESS : As you increase this
value, the picture outline
becomes stronger and clearer.
‫ڒڎڍڈڪڞڮ‬
M
 When the SHARPNESS level is too high, video
output may be unnatural or noisy.
OFF
OFF
ON
V-REV
SHARPNESS
RETURN
● SETUP
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
- V-REV : You can flip the picture
vertically on the screen.
IMAGE SETUP
䯝H-REV
SHARPNESS SETUP
䯝LEVEL
IIIIIIIIIIIIIIIIIIIIIIIÂIIIIIIIIIIIIIIIIIIIII
16
RETURN
‫ڋ‬
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
‫ڒڎڍڈڪڞڮ‬
y Monitor : Please change the settings value of video appropriate to your monitor.
CONTROLLER
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
‫ڋ‬
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
‫ڒڎڍڈڪڞڮ‬
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
SPECIAL SETUP
# PRIVACY
OFF
DAY/NIGHT
AUTO
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
䯝 MONITOR
LCD
DISPLAY
RETURN
‫ڋ‬
‫ڒڎڍڈڪڞڮ‬
CONTROLLER
- RET PKT : You can choose whether to send an ACK signal when the
communication control command is issued to the camera.
y IMAGE ADJ : Includes image quality or
special function factors.
➊ When the SETUP menu screen is displayed, select
‘IMAGE ADJ.’ using the Function Setup switch so
that the arrow indicates 'IMAGE ADJ.
➋ Select a desired mode using the Function Setup
switch.
34_ setup
SPECIAL SETUP
# PRIVACY
OFF
DAY/NIGHT
AUTO
DIS
OFF
SYNC
INT
COMM ADJ
䯝 IMAGE ADJ
MONITOR
LCD
DISPLAY
RETURN
- LCD : Please select this menu item
when using an LCD monitor.
- CRT : Please select this menu item
when using a CRT monitor.
LCD MONITOR SETUP
䯝GAMMA
0.45
IIIIIIIIÂIIIIIIIIIIIIIIIIIIIII
17
PED LEVEL
COLOR LEVEL IIIIIIIIIIIIIIIIIÂIIIIIIIIIIII
50
RETURN
CRT MONITOR SETUP
IIIIIIIIÂIIIIIIIIIIIIIIIIIIIII
䯝PED LEVEL
17
IIIIIIIIIIIIIIIII
IIIIIIIIIIII
Â
50
COLOR LEVEL
RETURN
English_35
setup
- USER : Please use this menu item when using
a monitor other than standard ones.
You can change the gamma, PED
level, and color gain in the sub menus.
USER MONITOR SETUP
䯝GAMMA
0.55
PED LEVEL
IIIIIIIIÂIIIIIIIIIIIIIIIIIIIII
17
COLOR LEVEL
IIIIIIIIIIIIIIIIIÂIIIIIIIIIIII
50
M
 Correcting Mistakes
RETURN
y DISPLAY : Use this feature to designate a
name for the camera, which will display on
the monitor screen.
- CAM TITLE : If the camera is named, it is
displayed on the monitor.
➊ Press the Function Setup switch to display the main
setup menu and move the arrow indicator to ‘CAM
TITLE’ using the Function Setup switch.
➋ Set ‘CAM TITLE’ to ‘ON’ using the Function Setup
switch.
M
 If the CAM TITLE feature is set to ‘OFF’, the name
will not displayed in the monitor
➌ Press the Function Setup switch.
➍ You can enter up to 15 characters.
a. Move the cursor to the character entry field
using the Function Setup switch.
b. Use the 4 direction of Function Setup Switch
to select a desired character.
c. Press the Function Setup switch to confirm
the selection of the blinking character. The
character is then saved, and the cursor in the
entry field moves to the next position.
d. Repeat steps 'a' through 'c' until the desired
name has been entered.
36_ setup
SPECIAL SETUP
# PRIVACY
OFF
DAY/NIGHT
AUTO
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
MONITOR
LCD
䯝 DISPLAY
RETURN
➎ Enter a title, move the cursor to ‘POS’ and press
the Function Setup Switch. The entered title
appears on the screen. Select the position to
display the title on the screen by moving the 4
direction of Function Setup Switch and press
the Function Setup Switch. When the position is
determined, select.
- CAM ID : Displays camera ID on top left corner of the screen.
- CAM INFO : Displays camera information on screen.
- MOTION ALARM : You can toggle the use of the camera alarm.
- ZOOM MAG : Use th is feature to display the current zoom magnification level on
screen. Position the indicator over ‘ZOOM MAG’ using the Function
Setup switch. Then set to ON using the Function Setup switch.
DISPLAY SETUP
䯝CAM TITLE
OFF
CAM ID
ON
CAM INFO
ON
MOTION ALARM
OFF
ZOOM MAG
ON
FONT COLOR
WHITE
ENGLISH
LANGUAGE
RETURN
CAMERA TITLE SETUP
A B C D EF G H I J K L M
N O P Q R S T U V WXY Z
abcdefghi j klm
n o p q r s t u v wxy z
- . 0123456789
← → CLR POS END
FRONT DOOR
- FONT COLOR : You can select the font color(white,yellow,green,red,blue)
- LANGUAGE : You can select the menu language according to your requirements.
• NTSC : Korean, English, French, Spanish, Japanese, Portuguese,
Taiwanese
• PAL : English, French, German, Spanish, Italian, Chinese, Russian, Czech,
Polish, Portuguese, Romanian, Serbian, Swedish, Danish, Turkish
- END : Select this to save the SPECIAL menu settings and return to the
SPECIAL menu.
RESET
To reset your camera to factory default condition.
EXIT
To finish setup menu.
English_37
● SETUP
Move the cursor th ‘CLR’ and press the Function Setup switch to clear the entire entry.
To modify one character, use LEFT or RIGHT to position the cursor above the character to be
modified and click the Function Setup switch after selecting the character to enter.
troubleshooting
specifications
TROUBLESHOOTING
SPECIFICATIONS
SCO-2370N
If the product does not function properly, please see the below for trouble shooting.
SCO-2370P
POWER
PROBLEM
The image on the screen is dim.
The image on the screen is dark.
The camera is not working
properly, and the surface of the
camera is hot.
f Check that the power cord and line connection between the
camera and monitor are fixed properly.
f Check that you have properly connected VIDEO cable to the
camera VIDEO output jack.
Power Consumption
Max. 3.8W, 4.8W ( DC12V / AC 24V, Fan & Heater Off )
Max. 28W ( Heater & Fan On, AC 24V )
Video
1/4” Super HAD CCD
f Is lens stained with dirt? Clean your lens with soft, clean cloth.
f Set the monitor to proper condition.
f If the camera is exposed to too strong light, change the camera
position.
Total Pixels
811(H) x 508(V)
795(H) x 596(V)
Effective Pixels
768(H) x 494(V)
752(H) x 582(V)
Scanning System
2 : 1 Interlace
2 : 1 Interlace
Synchronization
Internal / Line lock
f Adjust the contrast feature of the monitor.
f If you have an intermediate device, set the 75Ω / Hi-z properly.
Frequency
H : 15.734KHz / V : 59.94Hz
Horizontal Resolution
Color : 600 TV Lines, B/W : 700 TV Lines
f Check that you have properly connected the camera to an
appropriate power source.
Min. Illumination
Color : 0.2 Lux (50IRE@F1.2), 0.0004 Lux (Sens-up, 512x)
B/W : 0.02 Lux (50IRE@F1.2)
f Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
f Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or
‘MANUAL’.
The Motion Detection function does
not work.
f Check that MOTION DET of SPECIAL SETUP menu is ‘OFF’.
Color is not correct.
f Check the setting of WHITE BAL SETUP menu .
The screen flickers continually.
f Check that direction of camera turns toward the Sun.
38_ troubleshooting
Dual ( AC 24V, DC12V )
Imaging Device
The SENS-UP function does not
work.
When coaxial communication is
not available:
Input Voltage
f Make sure that the camera and monitor are installed within the
recommended distance.
f Use the video amplifier equivalent to coaxitron if the
recommended installation distance is exceeded.
● SPECIFICATIONS
Nothing appears on the screen.
SOLUTION
S / N (Y signal)
52dB (AGC off, Weight on)
Video Output
CVBS : 1.0 Vp-p / 75Ω composite
H : 15.625KHz / V : 50Hz
Lens
Zoom Ratio
37x (Optical), 16x (Digital)
Focal Length
3.5 ~ 129.5mm (F1.6 ~ 3.9)
Max. Aperture Ratio
1 : 1.6(Wide) ~ 3.9(Tele)
Angular Field of View
H : 55.5°(Wide) ~ 1.59°(Tele) / V : 42.5°(Wide) ~ 1.19°(Tele)
Min. Object Distance
150cm (Tele)
Focus
Auto / Manual / One push
Zoom Movement Speed
2.8 sec ( Wide to Tele )
Operational
On Screen Display
English, Japanese, Spanish, French,
Portuguese, Taiwanese, Korean
Camera Title
Off / On ( Displayed 15 characters )
Backlight Compensation
BLC/HLC/Off
SSDR
On / Off
Digital Noise Reduction (2D+3D)
On / Off
Digital Image Stabilization
On / Off
English, Spanish, French, Italian,
German, Polish, Russian, Czech,
Chinese, Danish, Portuguese, Romanian,
Serbian, Swedish, Danish, Turkish
English_39
specifications
DIMENSION
SCO-2370N
SCO-2370P
On / Off ( 8 Area )
Privacy Function
On / Off (12 Areas, Rectangle Type )
Sens-up (Frame Integration)
Auto / Off (Selectable x2 ~ x512)
Gain Control
Low / Medium / High / Manual / Off
White Balance
AWC/Manual/Outdoor/Indoor/ATW (1700°K~11,000°K)
Electronic Shutter Speed
1/60 ~ 1/1200,000
Digital Zoom
On / Off (2x ~ 16x)
Flip / Mirror
On / Off
Communication
RS-485 & Coaxial Control (Pelco Coaxitron)
Protocol
Samsung-T, Samsung-E, Pelco-D, Pelco-P, AD, Bosch, Honeywell, Vicon, Panasonic
● SPECIFICATIONS
Motion Detection
ENVIRONMENTAL
Operating Temperature / Humidity
-50°C to +50°C / Less than 90% RH (AC 24V)
-30°C to +50°C / Less than 90% RH (DC 12V)
Weather Proof
IP68
MECHANICAL
Dimension
Ø114 x 378mm
Weight
1.95Kg(4.29lb)
 The specification for this product may change without prior notice for product improvement.
40_ Specifications
English_41
STW protocol command description
STW PROTOCOL COMMAND DESCRIPTION
Reset
Byte2
Byte3
Command Packet
STX
CAM ID
HOST ADDR
Return Packet
STX
CAM ID
HOST ADDR
Checksum
CHECKSUM CALCULATION : UNARY OPERATION OF SUMMAT
ION FROM BYTE2 TO BYTE9.
EX) CHECKSUM = ~(BYTE2+BYTE3+... +BYTE8+ BYTE9);
Function
Reset all data to factory default value.
Byte9
Byte10
Byte11
CAMMAND
DATA3
DATA4
DATA5
DATA6
ETX
CHECKSUM
CAMMAND
DATA3
DATA4
DATA5
DATA6
ETX
CHECKSUM
HOST ADDR
000Fh
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
000Fh
00h
00h
00h
00h
AFh
CHECK SUM
Move focus lens to far direction.
Command Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Move focus lens to near direction.
Command Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
Move zoom lens to wide direction.
Command Packet
A0h
CAM ID
HOST ADDR
0040h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0040h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Zoom Tele
Byte8
CAM ID
Function
Zoom Wide
Byte7
A0h
Function
Focus Near
Byte 6
Command Packet
Function
Focus Far
B yte4 ll Byte5
Move zoom lens to tele direction.
Command Packet
A0h
CAM ID
HOST ADDR
0020h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0020h
00h
00h
00h
00h
AFh
CHECK SUM
42_ STW Protocol Command Description
English_43
● STW PROTOCOL COMMAND DESCRIPTION
Command Name
Byte1
STW protocol command description
Function
ZOOM Direct
A0h
CAM ID
HOST ADDR
00FFh
P1
P2
P3
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
00FFh
P1
P2
P3
00h
AFh
CHECK SUM
Parameter
P1, P2 : OPTICAL ZOOM = 0000h~06EAh
P3 : DIGITAL ZOOM = ((256*10)/Ratio)-1
EX) D-ZOOM 1.1x : P3 = E7h = ((256*10)/11)-1, Ratio 11 me ans 1.1x.
D-ZOOM 2.0x : P3 = 7Fh = ((256*10)/20)-1, Ratio 20 me ans 2.0x.
Function
Stop zoom & focus lens moving.
Command Packet
A0h
CAM ID
HOST ADDR
0000h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0000h
00h
00h
00h
00h
AFh
CHECK SUM
Function
One push AF
Unconditionally execute auto focus.
Command Packet
A0h
CAM ID
HOST ADDR
0045h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0045h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Save current user preset configuration information.
Command Packet
A0h
CAM ID
HOST ADDR
0003h
P1
00h
00h
00h
Afh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0003h
P1
00h
00h
00h
Afh
CHECK SUM
User Preset Save
Parameter
P1:00h(USER PRESET 1) ~ 80h(USER PRES ET 128)
Function
Execute selected user preset.
Command Packet
A0h
CAM ID
HOST ADDR
0007h
P1
00h
00h
00h
Afh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0007h
P1
00h
00h
00h
Afh
CHECK SUM
User Preset Exec.
Parameter
P1:00h(USER PRESET 1) ~ 80h(USER PRES ET 128)
Function
Clear selected user preset.
Command Packet
A0h
CAM ID
HOST ADDR
0005h
P1
00h
00h
00h
Afh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0005h
P1
00h
00h
00h
Afh
CHECK SUM
User Preset Clear
Parameter
P1:00h(USER PRESET 1) ~ 80h(USER PRES ET 128)
44_ STW Protocol Command Description
English_45
● STW PROTOCOL COMMAND DESCRIPTION
AF Stop
Command Packet
STW protocol command description
Function
Display OSD menu on the screen.
Clear OSD menu and save current menu setup.
Command Packet
A0h
CAM ID
HOST ADDR
00B1h
P1
00h
00h
00h
Afh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
00B1h
P1
00h
00h
00h
Afh
CHECK SUM
OSD Menu On/Off
P1 : 00h = ON
01h = OFF
Function
Move OSD arrow to up.
Command Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
Function
OSD Menu Down
Command Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Function
OSD Menu Left
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Move to inside menu
Command Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Function
OSD Menu ESC
Move OSD arrow to right.
Command Packet
Function
OSD Menu Set
Move OSD arrow to left.
Command Packet
Function
OSD Menu Right
Move OSD arrow to down.
Move to upper menu.
Command Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
46_ STW Protocol Command Description
English_47
● STW PROTOCOL COMMAND DESCRIPTION
OSD Menu Up
Parameter
MEMO
DECLARATION OF CONFORMITY
Application of Council Directive(s)
2004 / 108 / EC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
European Representative Name
European Representative Address
Equipment Type/Environment
CCTV Camera
Model Name
SC0-2370P
Beginning Serial NO.
C54N6V3Z300001X
Year of Manufacture
2010.03.24
Conformance to
EN 55022 : 2006
EN 50130-4 : 2003
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer
SAMSUNG TECHWIN CO., LTD
Signature
Legal Representative in Europe
Signature
Full Name
BONJENG GU
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place
CHANGWON, KOREA
Place
Date
2010.03.24
Date
MEMO
MEMO
MEMO
MEMO
MEMO
MEMO
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222, FAX : +1-310-632-2195
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300, FAX : +44-1932-45-5325
P/NO. : Z6806134201A/01