Fixtured Nutrunners and Components for Assembly Catalog

FIXTURED NUTRUNNERS
AND COMPONENTS
FOR ASSEMBLY
TA B L E O F C O N T E N T S
About AIMCO . . . . . . . . . . . . . . . . . . . . . . . 3
DC Multi-Spindle Systems . . . . . . . . . . . . 4
DC InLine Nutrunners . . . . . . . . . . . . . . . . 5
Inline Spindle Options. . . . . . . . . . . . . . . 6
DC Angle Nutrunners . . . . . . . . . . . . . . . . 7
Evolution Controller . . . . . . . . . . . . . . . . 8
Network Connectivity . . . . . . . . . . . . . . 9
URYU F-Series . . . . . . . . . . . . . . . . . . . . . 10
URYU F-Series Network Connectivity . . 13
URYU Nutrunners . . . . . . . . . . . . . . . . . . 14
ABOUT AIMCO
Founded in 1970, AIMCO is an experienced
leader in producing turnkey assembly
solutions. AIMCO specializes in fixtured tools
as well as other critical fastening technologies
used in manufacturing. By combining the
AIMCO customizes and monitors
your project from concept all the way
through final assembly, installation
and production start-up.
strengths of AcraDyne and URYU Seisaku, Ltd.,
AIMCO has the unique ability to offer the
most complete line of fixtured nutrunners in
the industry.
Whether integrating our nutrunners into your
own system or allowing us to design and
assemble a complete system for you, AIMCO
is there to support your requirements from
conception to implementation. From hand
guided simple two spindle powerheads to
fully integrated logic controlled robotic
assembly stations, AIMCO has the skill and
talent required to provide you with a system
that will exceed your expectations.
AIMCO’s expert attention provides you with
manufacturing efficiency, high productivity,
cost-savings and value! We are committed to
being your source for the highest quality
products, unsurpassed service and exemplary
industry expertise.
Let us be a part of your solution, today!
Call today for a free consultation.
Let us put our state-of-the-art products to work for you!
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
3
DC MULTI-SPINDLE SYSTEMS
FE A TUR E S
M U L T I P L E N U T RU NN I N G S Y S TE M S
AIMCO is able to integrate the
AcraDyne tool into a customized
Multiple Nutrunning System. From
simple systems vertically suspended
above the part to assembly stations that
integrate with your line, AIMCO can
handle your project.
Tell us your requirements and we’ll
propose a solution tailored to your needs.
Nutrunner sequencing — This allows nutrunners to be sequenced at
each phase of the tightening process allowing even distribution of
torque and load to each fastener.
Even torque distribution — Where there is uneven torque distribution,
part damage or distortion could occur with possible fastener failure or
loss of residual torque.
Snug, threshold, final torque in one pass — No need for multiple
torque stage sequencing as with a single nutrunner tool. Fixtured
nutrunners save time and effort from start to finish.
No missed fasteners — With multiple nutrunners there is a spindle
dedicated to each location, ensuring quality on every rundown on
every bolt.
Better residual torques — Synchronized controlled fastening allows
residual torque levels to be more consistent with the dynamic torque
specification.
Saving in cycle time — Compared with using a single nutrunner tool
with many rundowns, running all fasteners simultaneously reduces instation cycle time.
Cost saving benefits — Saving installation cycle time frees up operators
to handle additional tasks and potentially reduce labor requirements, at
the same time eliminating bottle necks.
Collect data — Most common methods of collecting data for quality
control and statistical analysis can be implemented from serial data
string using RS232 to formatted data from a network database.
E N G I NE M A NU F A C T U R E R
Gasoline generator assembly
Six (6) spindle 30 Nm
Replaced hand assembly with
rotation pattern to simultaneous
rundown
Custom display panel showing
application
Cpk range of 3.2 - 6.9 far
exceeded quality requirements
A U T O MO T I V E
M A NU F A C TU R E R
Wheel lug nut assembly
Four (4) spindle 105 Nm
Rotating spindle trunnion
Replaced competitive system
Built-in PC for data storage
7-Spindle Auto Down Assembly System
4
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
DC INLINE NUTRUNNERS
A C R A D YN E I NL I N E NU T R U N NE R S
When you require functionality, durability and flexibility, AIMCO’s complete
line of fixtured nutrunners provide the solution for automated, semi-automated
or manually operated fixtured installations. AcraDyne can design from 2 to 20
spindle systems.
AcraDyne Ti-Series nutrunners are engineered for performance and long life.
Our factory uses an innovative transducer technology unmatched in the industry.
N O N- C O N T AC T TR A N S D U C E R
Our innovative transducer utilizes
a permanent magnet bonded to
the gear carrier. Changes in the
magnetic field under load
determine the torque.
SM A L L DIA M E TE R B O DIE S
Smaller diameter tools mean tighter
bolt center-to-center dimension can
be achieved without off set heads.
AEM-2010
AEM-2020
AEM-2025
Minimum Pitch Circle
Refer to the chart for minimum side to center without offset heads.
AEM-2038
AEM-2068
AEM-3040
AEM-3060
AEM-3100
AEM-3150
AEM-3230
MODEL
TORQUE RANGE
(approx)
Nm
AEM-2010
AEM-2020
AEM-2025
AEM-2038
AEM-2068
AEM-3040
AEM-3060
AEM-3100
AEM-3150
AEM-3230
4 - 10
8 - 20
10 - 25
15 - 38
27 - 68
16 - 40
24 - 60
40 - 100
60 - 150
92 - 230
ft-lb
3-7
5 - 14
7 - 18
11 - 28
19 - 50
12 - 30
17 - 44
30 - 73
44 - 110
68 - 170
FREE SPEED
(approx)
rpm
OVERALL
LENGTH
SIDE TO
CENTER
in
mm
in
mm
2,600
1,500
1,025
700
400
1650
1125
620
415
280
11.5
11.5
11.5
14.4
14.4
15.9
15.9
20.3
20.3
20.3
292
292
292
365
365
404
404
515
515
515
.92
.92
.92
.92
.92
1.0
1.0
1.0
1.0
1.0
23.4
23.4
23.4
23.4
23.4
25.4
25.4
25.4
25.4
25.4
WEIGHT
LESS SOCKET
lb
kg
2.2
2.2
2.2
3.2
3.2
4.7
4.7
7.6
7.6
7.6
1.0
1.0
1.0
1.4
1.4
2.1
2.1
3.4
3.4
3.4
OUTPUT
DRIVE
in
3/8 sq. dr.
3/8 sq. dr.
3/8 sq. dr.
3/8 sq. dr.
3/8 sq. dr.
1/2 sq. dr.
1/2 sq. dr.
1/2 sq. dr.
1/2 sq. dr.
1/2 sq. dr.
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
5
INLINE SPINDLE OPTIONS
SL IDIN G SPIN DLES
Sliding spindles use a fast-lead or standard
socket with a soft-start spring benefit built
into the spindle.
S P R I N G L O A D E D S O CK ET S
DESIGN YOU R OWN DUAL DRIV E
Spring-loaded sockets allow for
self-alignment during a soft-start,
limiting the number of bad torques
because of sockets not properly
engaging. Spring-loaded sockets work
well where a sliding spindle may be
too long.
As easy as 1-2-3!
1. Supply the distance from center
point to center point of two fasteners
2. Select optional spring loaded socket
or sliding spindle
3. Supply application torque range
4. We can machine a custom plate that
fits into our off-the-shelf system
O F F SE T H E A D S/O P T I O NS
For systems where the center radius is
closer than our tool’s center radius, we
can incorporate offset heads — geared
fixtures that move the center drive
into a narrower center radius.
S Y NC H R O N I Z AT I O N VS .
N O N- S Y N C H R O NI Z A TI ON
Systems can be designed to fasten until
snug and then tighten to final torque
thus synchronizing the clamp load or
the system can be designed to tighten
each fastener at its own rate. All
AcraDyne systems by default are
synchronized for optimal quality.
R E M O TE ST A R T
Using logic inputs on our controllers
we can integrate any standard remote
switch from single contact to optical.
Whatever switch suits the purpose can
be integrated into the system.
Let us help design
your system!
6
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
DC RIGHT ANGLE NUTRUNNERS
D C R I G H T A NG L E NU TR U N NE R S
Right angle nutrunners are commonly thought
of as hand operated tools. Where vertical space
or access issues exist, AcraDyne right angle
nutrunners can be fixtured for custom solutions.
Lightweight angle heads smoothly transfer
torque to your application. We provide tools
from 6 to 450 Nm with many programmable
strategies to make for a perfect solution to meet
your assembly requirements.
AEN-2015
AEN-2025
FE A TUR E S
Simple yet sophisticated
Fast cycle times
Broad torque range of tools
Less than 50 parts per tool
Non-contacting transducers
Easy service and repair
AEN-2030
AEN-2040
AEN-2055
AEN-3055*
AEN-3060
AEN-3090
AEN-3120*
AEN-3200*
AEN-3300
AEN-3450
* Not ShowN
MODEL
AEN-2015
AEN-2025
AEN-2030
AEN-2040
AEN-2055
AEN-3055
AEN-3060
AEN-3090
AEN-3120
AEN-3200
AEN-3300
AEN-3450
TORQUE RANGE
(approx)
Nm
ft-lb
6 - 15
10 - 25
12 - 30
16 - 40
22 - 55
22 - 55
24 - 60
36 - 90
50 - 120
80 - 200
120 - 300
180 - 450
4 - 11
7 - 18
8 - 22
11 - 30
16 - 40
16 - 41
18 - 44
27 - 66
37 - 88
59 - 147
63 - 221
132 - 330
FREE SPEED
(approx)
rpm
OVERALL
LENGTH
in
mm
1,725
975
950
675
450
1,075
1,075
725
530
310
190
125
12.3
12.3
12.2
12.2
15.4
16.6
17.1
17.1
18.7
20.9
21.3
21.3
311
311
308
308
391
421
434
434
475
530
541
541
ANGLE HEAD
HEIGHT
in
mm
1.3
1.3
1.6
1.6
1.6
1.6
1.8
1.8
2.2
2.2
2.6
2.6
33
33
41
41
39
39
46
46
55
55
67
67
CENTER TO
OUTSIDE
in
mm
0.5
0.5
0.7
0.7
0.7
0.7
0.8
0.8
1.1
1.1
1.3
1.3
13
13
18
18
18
18.0
20.0
20.0
27.0
27.0
32.0
32.0
WEIGHT
LESS SOCKET
lb
kg
2.2
2.2
2.6
2.6
3.5
4.9
5.2
5.2
6.5
6.5
9.6
9.6
1.0
1.0
1.1
1.1
1.5
2.2
2.3
2.3
3.0
3.0
4.3
4.3
OUTPUT
DRIVE
in
3/8 sq. dr.
3/8 sq. dr.
3/8 sq. dr.
3/8 sq. dr.
3/8 sq. dr.
3/8 sq. dr.
1/2 sq. dr.
1/2 sq. dr.
1/2 sq. dr.
3/4 sq. dr.
3/4 sq. dr.
3/4 sq. dr.
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
7
EVOLUTION CONTROLLER
FE A TUR E S
Only one controller is required to
run all the range of the AcraDyne
DC electric tools — no need to
match tools to controllers, especially
during line changes
Three models of controller from
simple to sophisticated
Menu driven keypad makes
on-board changes easy
Quick Start for one step
programming
For Plug-n-Play, AcraDyne
accessories are installed via an
RJ45 connection
Panel mounted, remote mounted
or handheld, the KDM program
module is convenient
Standard ISA PC architecture is
expandable for future needs
Logic I/O is available, providing
fully programmable functions
Three ISA expansion slots available
Common external controls, such
as remote start/stop, annunciation,
and parameter select can be
pre-programmed
Power to operate lights, line control
devices or annunciators is built-in
for up to 4 amps
8
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
Password protection available
Eight parameter sets with 17
programmable features each —
accessible through 3-position
lightring, socket tray, or keypad
Optional internal PC with hard
drive for virtually unlimited data
storage and communications
(EV-III models)
Displays statistics of Cp, Cpk, 6
sigma range, mean and range of
last 100 readings
Easy to use with ToolWare software
for programming, fastening curve
analysis, and troubleshooting
Controller automatically reads tool’s
ID board for torque capacity,
calibration values, serial number,
and correct operation
Patented safety features of tubenut
wrenches are pre-programmed and
embedded
GFCI (ground fault circuit
interrupter) is provided on all 110V
units as standard equipment
Available for 110V-230V, 50/60 Hz
Adaptable for bottom or top cable connections
NETWORK CONNECTIVITY
AcraDyne Evolution Controller
DESCRIPTION
EV-I
EV-II
EV-III
• Digital readouts of torque, angle or fastener count
• operator interface via KDM (Keypad Display Module) for
programming or laptop PC with toolware™
• Plug-N-Play CAN architecture
All features of the EV-I plus:
• 24 I/o programmable interface. 24 VDC contact closure
• Screw terminals and built in power supply rated to deliver 4 amps
All features of the EV-I and EV-II plus:
• Pentium™ PC with hard drive
• windows® operating system. Supports networking
• three open ISA expansion slots
MODEL
KDM*
INPUT
HARD DRIVE
H XW X D
I/O
AEC-1110K
oPt
110V
EV-III only
14 x 8 x 12
AEC-1220K
oPt
220V
EV-III only
14 x 8 x 12
AEC-2110K
AEC-2220K
oPt
oPt
110V
220V
EV-III only
EV-III only
14 x 8 x 12
14 x 8 x 12
YES
YES
AEC-3110K
AEC-3220KXP
oPt
oPt
110V
220V
YES
YES
14 x 8 x 12
14 x 8 x 12
YES
YES
EV-II, EV-III
only
EV-II, EV-III
only
* to order controller without KDM, remove “K” from model number
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
9
URYU F-SERIES
Integrated type SPINDLE UNIT
(spindle controller and driver
unit) model UEC-F120 with
optional display unit UEC-MKB2
FE A TUR E S
Reduced Cable Numbers — Integral type tube containing torque sensor
cable and resolver cable.
Enhanced Memory Capacity — We have increased memory capacity to
get better efficiency of assembly line and tightening data control.
Open Network Communication — We have prepared all types of
communication boards for your various specifications (M-NET, Device
net, Inter-bas, CC-link).
Automatic Setting (Automatic recommended value input) — Advance
value preparation per application will help you simplify your parameter
setting.
Space Saving — One piece structure contained spindle controller and
driver unit has reduced volume space occupancy by 40% to 60% of
ordinary elements.
NO. OF SPINDLES
1-Spindle
2-Spindle
5-Spindle
10-Spindle
PRODUCTIVITY
the speed and efficiency
of assembly.
ERGONOMICS
the physical relationship
between personnel and
mechanisms they use in the
assembly process.
RELIABILITY
Expected service life for its
intended job.
QUALITY
the adherence to engineering
specifications during the
assembly process.
10
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
VOLUME & WIDTH
BEFORE
cm
mm
16,800
24,360
47,040
84,840
200
290
560
1,010
VOLUME & WIDTH WITH F-SERIES
UEC-F024
UEC-F120
cm
mm
cm
mm
6,360
8,904
16,536
29,256
150
210
390
690
8,268
12,084
24,804
48,336
195
285
585
1,140
URYU F-SERIES
1
10
2
3
1
2
4
2
8
5
9
3
4
7
5
6
8
6
7
1
1
2
3
4
5
6
7
8
9
10
Power Socket
AC100~220V single phase
External Input/Output Connector
PLC1: input signal connector for control signal
input (fixed allocation)
PLC2: output signal connector for judgement
result and status output (free allocation)
Serial Port (Data Input Connector)
RS232C DAtA-IN accepts serial numbers, etc.
provided by external equipment such as a
barcode reader then outputs tightening data
together with serial numbers.
Serial Port (Data Output Connector)
RSC232C PRINtER outputs tightening result data
to your printer (free format)
Serial Port (Data Output Connector)
RSC232C PLC outputs tightening result data to
PLC (free format)
Serial Port (Data Output Connector)
RS485 outputs tightening result data to an
external exclusive display unit
PC Connector
RSC232C for communication with a PC
Spindle-to-Spindle Communication Connector
RS485 for internal spindle unit to spindle unit
communications
Manual Switches
RESEt, StARt, REVERSE and CAL
LED Display
PowER, M RUN, ACCEPt, REjECt and ALARM
1
2
3
4
5
6
7
8
Status Change Switch
RUN/BYPASS change switch
RUN: operation possible status
BYPASS: Non-operation status
External Communication Device
RS485 connector
Resolver Connector
tool and resolver connection
MON Connector (Monitor Output)
Analog torque electric pressure and angle
pulse output
T/D Connector
tools torque sensor connection
I/O Connector
External input and output control
connection
MOTOR Connector
Connection with tools magnet motor
AC IN Connector
AC200V~220V 3-phase power socket
1
2
Manual Operation Switches
StARt: manual start switch
REVERSE: Manual reverse switch
CAL: Manual calibration switch
RESEt: Manual reset switch
Data Display Operation Switch
MoDE switch
SEt switch
DAtA UP switch
DAtA DowN switch
NotE: Display unit (UEC-MKB) is an option.
The “F” Series Nutrunner System will satisfy multiple tightening patterns.
Torque Tightening
Torque
Angle Tightening
Angle
Plastic Range Monitor
Spline Press Ft Tightening
Pin Hole Alignment Tightening
Pre-Load Detection
Idle Operation Check
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
11
URYU F-SERIES
6-SPINDLE F-SERIES MULTIPLE SYSTEM
12
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
URYU F-SERIES NETWORK CONNECTIVITY
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
13
URYU NUTRUNNERS
INLINE NUTRUNNERS
TYPE
UNR-F015-45Nt
UNR-F015-65Nt
UNR-F015-200Nt
UNR-F015-280Nt
UNR-F015-350Nt
UNR-F050-270Nt
UNR-F050-630Nt
UNR-F050-730Nt
UNR-F050-880Nt
UNR-F050-1400Nt
UNR-F100-1300Nt
UNR-F100-1900Nt
UNR-F100-2500Nt
UNR-F100-3700Nt
UNR-F100-5400Nt
L1
L2
371
371
400
400
400
453.5
500.5
500.5
512.5
512.5
519.5
515.5
515.5
589
704.5
41
41
41
41
41
41
41
41
45
45
45
45
45
57
80
EXTERNAL DIMENSIONS (mm)
L3
D1
D2
P
12
12
12
12
12
12
16.5
16.5
20
20
20
20
20
30
40
40.5
40.5
40.5
40.5
40.5
50
50
50
50
50
62
62
62
62
62
38
38
38
38
38
38
38
38
48
48
48
48
48
58
70
51
51
51
51
51
51
62
62
62
62
62
76
76
76
90
A
B
TORQUE
SENSOR
MOTOR
TYPE
FLANGE
DESIGN
M6
M6
M6
M6
M6
M6
M8
M8
M8
M8
M8
M8
M8
M10
M10
9.5
9.5
9.5
9.5
9.5
9.5
12.7
12.7
15.88
15.88
15.88
15.88
15.88
19
25.4
tM-035
tM-035
tM-035
tM-035
tM-035
tM-035
tM-085
tM-085
tM-150
tM-150
tM-150
tM-250
tM-250
tM-400
tM-700
F015
F015
F015
F015
F015
F050
F050
F050
F050
F050
F100
F100
F100
F100
F100
(a)
(a)
(a)
(a)
(a)
(a)
(a)
(a)
(a)
(a)
(a)
(b)
(b)
(b)
(b)
Torque Sensor Specifications
TYPE
CAPACITY (Nm)
tM-035
tM-085
tM-150
tM-250
tM-400
tM-700
tM-1000
34.3
83.3
147
245
392
686
980
Rated Strain
2000X10–6
output Voltage
1.0mV/V
Non-Lineality
±0.5% R.o.
Influence on Zero Point ±0.1% R.o./°C
Due to temperature
temperature Rating
–10~+65°C
Input output Resistance
480Ω
Maximum Input Voltage
16V
Insulation Resistance Greater than 300Ω
overload Capacity
150%
Inline Motor Specifications
TYPE
UNR-F015-45Nt
UNR-F015-65Nt
UNR-F015-200Nt
UNR-F015-280Nt
UNR-F015-350Nt
UNR-F050-270Nt
UNR-F050-630Nt
UNR-F050-730Nt
14
TIGHTENING
TORQUE (Nm)
FREE SPEED
(rpm)
WEIGHT
(kg)
SPINDLE
UNIT
4.5
6.5
20
28
35
27
63
73
3,200
2,200
730
500
410
1,750
750
650
2.48
2.48
2.73
2.73
2.73
4.86
5.08
5.08
UEC-F024
UEC-F024
UEC-F024
UEC-F024
UEC-F024
UEC-F060
UEC-F060
UEC-F060
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
TYPE
UNR-F050-880Nt
UNR-F050-1400Nt
UNR-F100-1300Nt
UNR-F100-1900Nt
UNR-F100-2500Nt
UNR-F100-3700Nt
UNR-F100-5400Nt
TIGHTENING
TORQUE (Nm)
FREE SPEED
(rpm)
WEIGHT
(kg)
SPINDLE
UNIT
88
140
130
190
250
370
540
540
340
730
500
370
260
175
5.47
5.47
7.42
7.94
7.94
9.55
17.0
UEC-F060
UEC-F060
UEC-F120
UEC-F120
UEC-F120
UEC-F120
UEC-F120
URYU NUTRUNNERS
“F” Nutrunner Motors’ Minimum Pitch Circle
TYPE
Refer to minimum pitch circles for designing your machine.
UNR-F015-45Nt
UNR-F015-65Nt
UNR-F015-200Nt
UNR-F015-280Nt
UNR-F015-350Nt
UNR-F050-270Nt
UNR-F050-630Nt
UNR-F050-730Nt
UNR-F050-880Nt
UNR-F050-1400Nt
UNR-F100-1300Nt
UNR-F100-1900Nt
UNR-F100-2500Nt
UNR-F100-3700Nt
UNR-F100-5400Nt
UNR-F100-7000Nt
UNR-F100-10000Nt
DIMENSIONS (mm)
C
D
E
A
B
43
43
43
43
43
59
59
59
59
59
66
70
70
76
94
94
94
52
52
52
52
52
72
72
72
72
72
75
100
100
100
125
125
125
64
64
64
64
64
90
90
90
90
90
92
110
110
110
143
143
143
46
46
46
46
46
64
64
64
64
64
65
78
78
78
102
102
102
74
74
74
74
74
108
108
108
108
108
116
115
115
120
166
166
166
F
G
92
92
92
92
92
122
122
122
122
122
130
132
132
140
188
188
188
122
122
122
122
122
160
160
160
160
160
170
174
174
184
257
257
257
RIGHT ANGLE NUTRUNNERS
TYPE
UNR-F015-25NtC
UNR-F015-55NtC
UNR-F050-95NtC
UNR-F050-130NtC
UNR-F100-200NtC
UNR-F100-250NtC
UNR-F100-380NtC
UNR-F100-550NtC
EXTERNAL DIMENSIONS (mm)
H1
H2
D1
D2
L1
L2
507
521
643
649
681.5
677.5
716.5
784
120
130
150
150
170
170
200
200
49
58
73.5
73.5
85.5
85.5
109.5
114.5
10.6
18
20
20
20
20
25
29
70
70
85
85
85
100
110
110
28
36
45
45
56
56
74
74
P
A
B
85
85
102
102
102
120
134
134
M6
M6
M6
M6
M6
M8
M10
M10
9.5
12.7
15.88
15.88
15.88
15.88
19
25.4
TYPE
STRAIGHT MOTORS
SENSOR
MOTOR
tM-035
tM-035
tM-085
tM-150
tM-150
tM-250
tM-250
tM-400
F015
F015
F050
F050
F100
F100
F100
F100
UNR-F015-200Nt
UNR-F015-350Nt
UNR-F050-630Nt
UNR-F050-880Nt
UNR-F100-1300Nt
UNR-F100-1900Nt
UNR-F100-2500Nt
UNR-F100-3700Nt
Right Angle Motor Specifications
TYPE
UNR-F015-25NtC
UNR-F015-55NtC
UNR-F050-95NtC
UNR-F050-130NtC
TIGHTENING
TORQUE (Nm)
FREE SPEED
(rpm)
WEIGHT
(kg)
SPINDLE
UNIT
25
55
95
130
460
260
480
340
4.18
4.37
8.08
8.3
UEC-F024
UEC-F024
UEC-F060
UEC-F060
TYPE
UNR-F100-200NtC
UNR-F100-250NtC
UNR-F100-380NtC
UNR-F100-550NtC
TIGHTENING
TORQUE (Nm)
FREE SPEED
(rpm)
WEIGHT
(kg)
SPINDLE
UNIT
200
250
380
550
460
340
235
165
11.92
12.3
15.92
17.43
UEC-F120
UEC-F120
UEC-F120
UEC-F120
AIMCO / 1 - 8 0 0 - 8 5 2 - 1 3 6 8
15
POWER TOOLS
DC CO NTR OL LED FA ST EN ING T OOL S
TOR QUE MEA SUR EMENT SYST EM S
ASSEM BL Y SYST EMS
CORPORA TE HE ADQUART E RS
TOO L S UPPORT SYSTEMS
10000 S.E. Pine St.
Portland, OR 97216
(800) 852-1368
FAX (800) 582-9015
1204 E. Maple Rd.
Troy, MI 48083
(800) 852-1368
FAX (800) 582-9015
Ave. Morones Prieto 2110 Pte.
Col. Loma Larga
Monterrey, NL CP 64710, Mexico
52-81 1001-1600
FAX 52-81 1001-1630
FASTENER TOO LS
LIT-AD140
Printed 2.5k-10/06-CR-USA
Printed in USA
©2006 AIMCO
w w w .a im c o - glo ba l.c o m