Dension IPH-9201-5 Instruction manual

2. GETTING STARTED
•
iPod UI: the original user interface of the iPod
remains active (i.e. the click wheel still works) so
you can use it for browsing as normal. In this
mode the id3 tag info will not be displayed, time
counter is not synchronized and only ‘iPod UI’ will
appear on the screen
•
iPod GW: the click wheel or the touch screen
(iPhone, iPod touch) is disabled, iPod displays
the currently played song information, except on
touch and iPhone where ‘Accessory attached’
message is displayed. The iPod playback control
is possible from the car stereo (Head Unit) or the
steering wheel only. In this mode the id3 tag info
and the time is displayed on the radio display
(Radio dependent)
Before you start, please check that your iPod is up to
date. You can get the latest iPod firmware updates via
iTunes.
Gateway 500S BT
(GW52MO1 & GW52MO2)
iPod, USB, Bluetooth (HFP, A2DP) & AUX
3. OPERATION
Switch your car radio ON and select CD changer as
source. If in doubt consult the audio section of your car’s
instruction manual.
•
User Manual
v.1.1
G52-9201-3
1. INTRODUCTION
The Dension Gateway 500S BT lets you connect your
iPod or USB storage (stick, hard drive or mass storage
capable mp3 player) to your original car radio, providing
music playback, menu based control and charging.
The Gateway 500S BT also offers Bluetooth
connectivity for handsfree mobile call and music
streaming (via A2DP) using the original buttons and
screens of your vehicle.
Supported USB devices
USB Flash Memory and Hard Disk Drive
File System: FAT16 or FAT32
Storage capacity: up to 320 GB music content
Music Format: MP3, WMA and WAV
Supported iPod / iPhone devices via 30PIN dock
cable (not included in the package)
th
iPod (4 generation)
iPod nano (1st, 2nd, 3rd, 4th, 5th and 6th generation)
iPod mini
iPod Photo 4G
iPod Video 5G
iPod Classic
iPod Touch (1st, 2nd, 3rd and 4th generation)
iPhone, iPhone 4S /4 / 3GS / 3G and iPhone
Supported iPod / iPhone devices via “Lightning to
USB cable” (not included in the package)
iPod nano 7th generation
iPod Touch 5th generation
iPhone 5s / 5c / 5
Aux: 3.5mm stereo aux input
Depending on your Radio, the music menu can be
browsed with Radio buttons (Next / Back), MMI or iDrive controller (for further details please go to
Section 8).
Connect your iPod to the Gateway. It will start playing
the first song on the device. In case the Gateway has
been in use earlier, music will continue from the last
played point.
Switching off the car or the radio will stop playback and
put the source devices to stand-by (except which is
connected into AUX).
USB: the playback is controlled from the Gateway.
ID3 tag info will be displayed (if that details are
properly filled out)
•
GW AUX: in AUX mode the radio displays ‘AUX
GW’ on the radio screen and cluster display (Car /
Radio dependent). No control function is available
BT Audio: from a paired A2DP streaming capable
phone. The playback is controlled from the phone
or with the Next and Back buttons of your car
(phone dependent). In this mode the id3 tag info
can be displayed too on the radio screen (phone
dependent).
Please note: BT Audio feature is disabled by
default. It can be enabled from the Settings
menu
The volume menu allows you to set the different
volumes in the system:
•
iPod, AUX volumes for music playback
•
Phone and microphone volume for handsfree calls
Language
The language menu allows you to change the menu
language of the Gateway
Phonebook
5. ABOUT GATEWAY MENU
PB display order
Browsing and Selecting Music (iPod or USB)
You can change how your contacts are listed (First, Last
or Last, First)
You can use the other menu items to browse the
content of the iPod or USB device
Paired phone
•
Files, Artists, Albums, Titles, Bookmarks (for
USB only): Provides browsing and selecting the
music files on your USB device
Last four paired phone name (ID) will be listed here.
You can force pairing from this menu too if you click
select the phone from the list
•
Music (for iPod only): Allows browsing and
selecting music in the sub-menus: Playlist,
Artists, Albums, Songs, Genres, Composers,
Audiobooks and Podcasts
BT Audio
You can turn the BT Audio option ON if you want to play
music from mobile phone via A2DP. If you enable that
function, you need to turn the whole system OFF
completely till the blue LED goes OFF on the connector
port. When it happens you can turn the system back ON
and select the A2DP option from the source menu
Ringtone
You can disable all ringtones in phone functions
About
Provides information on the gateway product (SW
versions, serial number, etc.).
If no device is connected then AUX GW is displayed
and the time counter is just counting up.
•
Volume
In the phonebook menu you can switch off the
automatic download of the phone book, which is
required to work with certain phone models
Next / Back and Random / Repeat / Scan buttons (radio
dependent) work as expected.
You can select the music source for playback in the
Source Menu. This can be:
Settings menu
Please note: Gateway returns to playback screen after
15 - 30 seconds (radio dependent) of inactivity in any
other browsing mode.
You can pair a Bluetooth capable mobile phone for
music streaming (requires an A2DP capable phone) and
handsfree use (if that option is active in the Gateway).
Pairing is controlled from the mobile phone the same
way as connecting to other Bluetooth accessories. The
pin code to the Gateway 500S is 0000 (for further
details please see Section 6).
4. ABOUT SOURCES
Please note: In case the current list of the
playlist/album contains more than 30 items (songs) the
whole list cannot be displayed on the same screen due
to the technical limitation of the radio so it will be split to
pages (sub lists) containing 30 items.
6. PHONE FUNCTIONS
When an artist is selected the PLAY menu item, play all
the songs from the given artist. Selecting the ALL menu
option will lists all the songs from the given artists. The
albums from the artist are listed as separate items
afterwards.
When an album is selected, all the songs from the given
album are listed as separate items afterwards.
N.B. If the phone option is programmed and
activated on the car, then the 500S BT provides the
same functions as the factory phone module. Please
consult the owner’s manual for the correct way of
controlling.
•
Play All: plays all the music from the selected
source. The playback starts from the first song on
the device
Turn ON the Bluetooth option, search for available
devices, select GW500S BT and enter 0000 for
pairing. When a phone is connected then, you can
see the connection status on the Radio screen or
cluster display. To enter the phone menu press
‘PHONE’ or ‘TEL’ button or select Communication
option with the iDrive controller.
•
Album play: Plays the full album of the song is
being played, typically used in random play mode
If you are listening to Radio or CD then it works as
usual like the factory phone option.
The following menu items available in the main menu
serve as specific functions for music playback:
7. BT AUDIO PLAYBACK FROM A2DP SOURCE
Gateway 500S supports Advanced Audio Distribution
Profile (A2DP) / Audio / Video Remote Control Profile
(AVRCP) for audio playback. In this mode id3 tag will be
displayed on the radio screen (phone dependent) and
Next / Back / Pause / Play functions are available from
the car radio or the steering wheel (phone dependent).
8. SPECIFIC OPERATION GUIDES
BMW
The menu of the Gateway 500S is displayed on the
iDrive or the radio screen.
You can enter the Gateway main menu by pressing the
disc 6 where you can toggles between different sources
or browse by artist, album etc.
10. SERVICING A CAR
MOST optical system based vehicles have complex
system management capabilities, and servicing may
involve using a diagnostic computer.
Toggling between different menu options is possible
with the next (►►|) or previous track (|◄◄) buttons. In
order to select a menu item, press and hold (about 3
seconds) the next track (►►|) button. You can get back
to the previous menu level if you do the same procedure
with previous back (|◄◄) button.
Note: The Gateway menu can be reached by ‘Magaz.’
button as well where you can use side navigation
buttons also however for browsing and selecting the
same buttons needs to be used as above.
Porsche
To avoid conflict with such diagnostics devices, you can
use the switch on the Connector Port to put the
Gateway in Bypass mode, which temporarily disables
the operation of the Gateway. For normal use put the
switch to Active mode.
You can enter the Gateway main menu by selecting
‘Changer’ by the upper side button and then select
‘Menu’ by using the rotary knob.
The menu of the Gateway is displayed on the PCM
radio.
In order to switch to Bypass mode, turn the mode
selector button to Bypass, then fully turn off the engine
remove the ignition key and wait for the electronics to
switch off completely (Blue LED on the Connector Port
turns OFF). To get back to Active mode, turn everything
off completely till the car goes to sleep and select Active
mode on the Connector Port.
11. DISCLAIMER AND WARRANTY
Disclaimer
If your car’s electrical system begins to behave
erratically, please disconnect the Gateway interface
physically immediately and have it checked by your
installer. Dension and its authorized distributors and
retailers are not liable for any incidental consequential
or indirect damages or loss and do not assume liability
for any diagnostic fees.
The music playback and settings are controlled from the
radio or iDrive controller, but it is also possible to select
the next or the previous track from the steering wheel
buttons (if available).
You can enter the Gateway main menu by selecting disc
6 where you can toggles between different sources or
browse and select different music. For more information,
please Check section #5.
Browsing is possible on non-iDrive cars, by the next
or previous track buttons. In order to select a menu
item, press and hold the Fast Forward button (about 3
seconds). Press and hold the Fast Rewind if you want to
get back to the previous menu.
On iDrive based system turn the iDrive controller left or
right for browsing. Press the iDrive to select a song or
enter a menu, slide the controller UP and push the
iDrive controller to get back to the previous menu.
Mercedes-Benz
The menu of the Gateway is displayed on the Comand
radio.
The music playback and settings are controlled from the
radio, but it is also possible to select the next or the
previous track from the steering wheel (if available).
You can enter the Gateway main menu by selecting ‘CD
List’ and then ‘Menu’ by the right rotary knob. When
you entered to the Gateway Menu you can Toggle
between the different menu options by the next (>) or
previous track (<) buttons. In order to select a menu
item, press and hold (about 3 seconds) the next track
(>) button. You can get back to the previous menu level
if you do the same procedure with previous back (<)
button.
Please note: Depending on the radio type and software
version, you might receive the following error message
during start-up ‘System error: Phone not available.’
This message does not influence radio or Gateway
operations. Press ‘Confirm’ to dismiss this message.
After you will experience flawless operation.
AUDI
How to control
The menu of the Gateway is displayed on the MMI
screen.
The music playback and settings are controlled from the
radio, but it is also possible to select the next or the
previous track from the steering wheel (if available).
The music playback and settings are controlled from the
radio, but it is also possible to select the next or the
previous track from the steering wheel (if available).
Turn left or right the MMI rotary controller for browsing.
Press the same button to select a song or enter a menu.
Alternatively you can use the next track (>) button to
enter or select, if hold it for 3 seconds. You can get back
to the previous menu level, if you select the first menu
item in the list (at the top) or if you press and hold the
previous track (<)button.
9. CONNECTOR PORT
The Connector Port is a convenient glovebox mounted
port for USB and AUX input (3.5mm) and it has a MODE
selector switch and a reset button.
Use the Mode selector button and set Bypass mode to
reach the original CD-Changer functionalities if present.
Please note: You don’t need to use that mode button
on Audi with MMI High (colour) system.
The Connector Port has a reset button for the rare
occasion when a full hardware reset of the Gateway is
necessary.
The use of handheld devices while driving may be
subject to government legislation. Please ensure that
your use of the Dension device complies with applicable
traffic laws. Dension does not assume liability for any
events resulting from the illegal or irresponsible use of
handheld devices while driving.
Dension reserves the right to modify its products or
specifications without prior notice.
Warranty
Dension devices carry a one-year limited warranty that
protects you from defects in material and workmanship
of products sold by Dension or its authorized distributors
and retailers. Dension does not warrant any installation
work or assume liability for any damage caused due to
negligence, improper installation or operation. For
warranty claims, proof of purchase is required
Further assistance
If you need further assistance in using your Dension
product, please contact your local supplier or visit our
website at www.dension.com and check our user
videos. You can ask for the help of our trained
technicians by clicking 'Support'."
Please check the download section for the latest
firmware version and product documentation, as
these may provide additional features or easier use of
the product.