Eizo FlexScan T966 User`s manual

User’s Manual
FlexScan
T966
‚
Color Display Monitor
Important
Please read this User's Manual carefully to familiarize yourself with safe
and effective usage procedures. Please retain this manual for future
reference.
English
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them
carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and
can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury
and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
Copyright© 2002 by EIZO NANAO CORPORATION. All rights reserved. No part of this
manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any
means, electronic, mechanical, or otherwise, without the prior written permission of Eizo Nanao
Corporation.
Eizo Nanao Corporation is under no obligation to hold any submitted material or information
confidential unless prior arrangements are made pursuant to Eizo Nanao Corporation's receipt of
said information. Although every effort has been made to ensure that this manual provides upto-date information, please note that EIZO monitor specifications are subject to change without
notice.
ENERGY STAR is a U.S. registered mark.
Apple and Macintosh are registered trademarks of Apple Computer, Inc.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards
Association.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager and PowerManager, QuickSet and i·Sound are trademarks of Eizo Nanao
Corporation.
FlexScan, SuperErgoCoat and EIZO are registered trademarks of Eizo Nanao Corporation.
As an ENERGY STAR® Partner, Eizo Nanao Corporation has determined that this
product meets the ENERGY STAR guidelines for energy efficiency.
2
English
TABLE OF CONTENTS
PRECAUTIONS...................................................................................... 4
1. INTRODUCTION ..................................................................................... 8
1-1. Features ........................................................................................................8
1-2. Package Contents..........................................................................................8
1-3. Controls & Connectors ................................................................................9
2. INSTALLATION ..................................................................................... 10
2-1. Connecting the monitor to the PC ..............................................................10
2-2. Getting Ready for Operation ......................................................................12
3. SCREEN ADJUSTMENT ...................................................................... 13
3-1. How to use the ScreenManager ..................................................................13
3-2. Fine Contrast ..............................................................................................15
3-3. Color ..........................................................................................................16
3-4. Power Save .................................................................................................18
3-5. Adjustment Lock ........................................................................................19
3-6. Connecting two PCs to the Monitor ...........................................................20
4. MAKING USE OF USB (Universal Serial Bus) ................................... 21
5. TROUBLESHOOTING........................................................................... 23
6. CLEANING ............................................................................................ 29
7. SPECIFICATIONS ................................................................................. 30
8. GLOSSARY........................................................................................... 33
TABLE OF CONTENTS
3
English
PRECAUTIONS
IMPORTANT!
• This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
• To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).
[Location of the Caution Statements]
WARNING
If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or
equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or
burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers
may result in fire, electric shock, or equipment damage.
4
PRECAUTIONS
English
WARNING
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage.
If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Have the unit checked by a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate place may fall and result in injury or
equipment damage.
If the unit falls, disconnect the power immediately and ask your dealer for
advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock.
OK
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
* Do not place outdoors.
* Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
* Do not place in a dusty or humid environment.
* Do not place in a location where the steam comes directly on the screen.
* Do not place near heat generating devices or a humidifier.
To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.
Use the enclosed power cord and connect to the standard power outlet
of your country. Be sure to remain within the rated voltage of the
power cord.
Not doing so may result in fire or electric shock.
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage the cord and result in fire or electric shock.
OK
PRECAUTIONS
5
English
WARNING
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock.
Use the correct voltage.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may result in fire,
electric shock, or equipment damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
6
PRECAUTIONS
English
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables and remove the optional unit. Moving
the unit with the cord or the option attached is dangerous. It may result in
injury.
Do not move it alone. Always work with another person.
Moving it alone may cause lower back pain. Also note that the unit is heavier
at the front than at the rear.
OK
Do not block the ventilation slots on the cabinet.
* Do not place any objects on the ventilation slots.
* Do not install the unit in a closed space.
* Do not use the unit laid down or upside down.
* Do not remove the tilt-swivel stand.
Blocking the ventilation slots prevents proper airflow and may result in fire,
electric shock, or equipment damage.
Do not sit on the cabinet or place any heavy objects on the cabinet.
A unit with heavy objects on it may fall and result in injury.
Do not touch the plug with wet hands.
Doing so may result in electric shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power switch
for the safety and the power conservation.
PRECAUTIONS
7
English
1. INTRODUCTION
Thank you very much for choosing an EIZO Color Display Monitor.
1-1. Features
• Horizontal scanning frequency of 30-130kHz
Vertical scanning frequency of 50-160 Hz
• Support to sRGB standard (See page 34.)
• Max Brightness 230 cd/m2 bright screen (when the movie mode is selected.)
• The color restoration circuit that can keep stable brightness and color-tone for a long
period supported (See page 17.)
• Fine contrast modes, to adjust the most suitable brightness and contrast of the screen
(See page 15.)
• The EIZO CRT Utility Disk enclosed (See readme.txt in the CD-ROM for details.)
- The utility software “ScreenManager Pro for USB” (for Windows) to control a
monitor from a PC with a mouse and a keyboard
- The software “ActiveGamma” (for Windows/Macintosh) to assign fine contrast
modes to applications
- The software “DesktopViewer” (for Windows) to display bright and clear still
images
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
• Monitor
• Power Cord
• Signal Cable (MD-C87 or MD-C100)
• Setup Guide
• ScreenManager Quick Reference
• EIZO CRT Utility Disk (for Windows/Macintosh)
• EIZO USB Cable (MD-C93)
• LIMITED WARRANTY
NOTE
• Please retain the packing materials for future transference.
• The EIZO USB cable is used when using the software in the EIZO CRT Utility Disk.
For information on the software, refer to the readme.txt in the EIZO CRT Utility Disk.
8
1. INTRODUCTION
English
1-3. Controls & Connectors
Front
Rear
Bottom
(1)
(2)
(3)
(4)
(5)
USB Port*1 with a drop down access lid; Downstream x 1
BNC/D-SUB Selection Button
AUTO/FINE MODE button
Push the button lightly: Fine Contrast Mode Selection button
Press and hold the button more than 2 seconds: AUTO-SIZING button
QuickSet™ Control Pad
(Hereinafter “Control Pad”)
Power Indicator
Green
Power is on (Normal mode)
Flashing Green
Power save (Mode 1)
*2
Advance notice of monitor's Off Timer
Yellow
Power save (Mode 2)
Flashing Yellow
Power save mode with monitor's Off Timer*2
Off
Power is off
(6)
(7)
(8)
(9)
(10)
(11)
(12)
Power Switch
Power Terminal*3 (with a cover)
ScreenManager™
Power Connector
D-Sub mini 15 pin connector
BNC Input Connector
USB Port
Downstream ports x 3
Upstream port*4 x 1
*1
See page 21 for further details.
*2
Regarding the “Off Timer”, see page 19.
*3
*4
Power Terminal can be used with an optional i⋅Sound Sound Unit.
USB Port upstream is used when using the software EIZO CRT Utility Disk. (See page
11.)
1. INTRODUCTION
9
English
2. INSTALLATION
2-1. Connecting the monitor to the PC
NOTE
• Be sure that the power switches of both of the PC and the monitor are OFF.
1.
Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Signal Cable
2.
10
Connector
Signal Cable (enclosed)
D-Sub mini 15 pin
connector
Signal Cable (enclosed) +
Adapter* (optional)
D-Sub 15 pin
connector
PC
Standard Graphics Board
Macintosh G3 (Blue &
White) / G4
Macintosh
* Macintosh Adapter (optional)
Plug the power cord into the power connector at the rear of the
monitor. Then, plug the other end of the cord into a power outlet.
2. INSTALLATION
English
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country. Be sure to remain within the
rated voltage of the power cord.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock.
3.
Turn on the monitor first, then the PC.
Turn on the monitor first, then the PC. The monitor's power indicator will light up
(green).
The monitor will warm up briefly, then display an image.
Whenever finishing your operation, turn off the PC and the monitor. (If an image
does not appear, make sure that all connections have been made properly. Refer to
the “5. TROUBLESHOOTING” (See page 23) for additional advice).
4.
When using the software in the EIZO CRT Utility Disk: Connect the
upstream port of the monitor to the downstream port of the USB
compliant PC or another hub with the USB cable.
After connecting the USB cable, the USB function can be set up automatically. For
further details about the “ScreenManager Pro for USB”, refer to the readme.txt in
the CD-ROM.
To Downstream
Ports of the PC or
Another Hub
USB Cable
NOTE
• Generally, for maximum viewing comfort, position the monitor
slightly below eye level. Staring at the monitor for prolonged
periods can cause eyestrain. Be sure to take adequate rests.
(A 10-minute rest period each hour is suggested).
2. INSTALLATION
11
English
2-2. Getting Ready for Operation
Try each setting procedure if necessary in the following cases.
The display image size and/or position is not appropriate.
→ Press the AUTO/FINE MODE button on the front panel for more
than 2 seconds.
The AUTO-SIZING function centers the displayed image, aligning the image's
borders with respect to the monitor frame. In general, press the AUTO/FINE
MODE button whenever changing the graphics card or the resolution (p. 34), or
when image size and/or position is incorrect.
NOTE
• Pushing the AUTO/FINE MODE button lightly allows changing of the Fine
Contrast mode.
The display area is too large or too small.
→ Readjust the refresh rates.
Readjust the preferred refresh rates in accordance with the following look-up-table.
Refer to the PC or graphics card manuals on how to change the refresh rates.
[The maximum (non-interlaced) vertical refresh rates for the model]
Maximum Vertical Refresh rate (Hz)
640×480 800×600 1024×768 1280×1024 1600×1200 1600×1280 1920×1440
160
160
160
121
104
97
86
2048×1536
80
NOTE
• About Plug & Play of the monitor
When your computer and monitor support VESA DDC, the suitable resolution
and the refresh rate are set by just plugging your monitor into the computer
without any manual settings. When your computer system supports Plug &
Play, the Display Information File is not required except for installing the Color
Profile.
Further adjustment is required
→ Adjust the screen using the ScreenManager. (See page 13.)
12
2. INSTALLATION
English
3. SCREEN ADJUSTMENT
NOTE
• Allow the monitor to stabilize for at least 30 minutes before making image
adjustments.
3-1. How to use the ScreenManager
Use the control pad on the front panel. The control pad can be
pressed in 5 directions, Enter, Up, Down, Left and Right.
1.
Entering the ScreenManager
Up
Left
Right
Down Enter
Display the ScreenManager Main menu by pressing the center of the control pad.
Main menu displays the current connector type and frequency of the input signal.
[Main Menu]
2.
Making Adjustments and Settings
(1)
(2)
(3)
(4)
3.
Select the desired icon by using Up, Down, Left and Right keys.
Press the Eenter key to display each adjustment/setting menu or Sub menu.
Make the required adjustments/settings by using the control pad.
To save the adjustments/settings and return to the Main menu, press the Center
key.
Exiting the ScreenManager
To exit the ScreenManager, select the <Exit> from the Main menu and press the
Enter key.
Pushing the down arrow key twice goes to the <Exit> position instantly.
NOTE
• Leaving the ScreenManager idle for 45 seconds or more will turn the adjustment off
automatically without saving.
• The brightness and contrast can be adjusted by pressing the Up, Down, Left and
Right keys of the control pad directly. Press the center of the control pad to save and
exit the settings after the adjustment.
3. SCREEN ADJUSTMENT
13
English
Adjustments and Settings
Main Menu
Sub menu
Adjustments and Settings
Contrast
-
Screen contrast and brightness
Size
-
Screen Size
-
Position
-
Screen position
-
Screen
Side Pin.
Side pin balance
-
Trapezoidal
Distortion
-
Tilt
Inclination
-
Uniformity
Uniformity (p. 34)
p. 28
Convergence
Convergence (p. 33)
p. 26
Moiré Reduction
Moiré (p. 33)
p. 24
Fine Contrast
To Select Movie Settings (1 to 4)
p. 15
Signal Filter 1
To decrease the slightly shadowed images or
characters
p. 25
Signal Filter 2
To decrease the vertical bars
p. 25
Color Mode
To select the adjustment mode from standard p. 16
custom or sRGB
Color
•Standard
Others
14
See
page
-
p. 16
Temperature
To set the color temperature. (p. 33)
Color Correction
To eliminate disparities in color temperature
p. 16
and brightness due to a irregular video signal
output
p. 16
Color Restoration
To restore the changed brightness and the
color caused by long use to close to those
original ones.
p. 17
•Custom
To adjust each color, (Red, Green and Blue)
p. 17
•sRGB
To select sRGB (p. 34)
p. 17
Power Manager
To set the power save (with PC's power
saving system)
p. 18
Off Timer
To set the power save (with Monitor's off
timer)
p. 19
Degauss
To degauss (p. 33)
p. 26
Beep
To set beeper on/off.
-
Menu Position
To adjust the menu position of the
ScreenManager
-
Language
To select the preferred language to use
-
Input Priority
To select the priority input signal
p. 20
Reset
To return to the factory default setting
p. 26
Information
To know the total usage time
p. 17
3. SCREEN ADJUSTMENT
English
3-2. Fine Contrast
The fine contrast modes differ in brightness and contrast settings. Select the mode that is
the best suited to the application in use. The mode can be changed with the
AUTO/FINE MODE button that is on the front of the monitor.
To select the most suitable brightness mode
→ Push AUTO/FINE MODE button lightly.
Select from the following modes to adjust the most suitable brightness of the
screen. Pushing this button displays the fine contrast modes in the following order.
(Text→ Browser→ Picture→ Graphic→ Movie→ Text…)
Text
Text on word processor or spreadsheet software
Browser
Text and picture image (ex. home page)
Picture
The photo or picture image
Graphic
Animation or illustration (Contrast is not enhanced.)
1
Movie*
The animated image (games or DVDs)
dark still images
NOTE
• When changing the mode or adjusting the contrast, the brightness of the
screen might change for a split second.
• The color temperature and the brightness can be set in the each mode.
• *1There are 4 kinds of movie mode settings. Set the mode by using the <Fine
Contrast> in the <Screen> menu (Refer to the following section for details).
To select proper Movie Mode
→
Select a proper Movie Mode in <Fine Contrast>.
Select a mode from the following 4 options when adjusting the contrast or the
sharpness settings.
Set the mode by using the <Fine Contrast> in the <Screen> menu.
Mode
Enhanced
contrast*2
Enhanced
sharpness
Movie 1
ON
ON
DVDs and TV with full-screen
Movie 2
ON
OFF
DVDs and TV with default screen
Movie 3
OFF
ON
Movie 4
OFF
OFF
When the brightness or sharpness of
the input images has been already
compensated
*2
Suitable for;
To display clear images, the monitor checks the input signal then corrects
the mid-range color tone and further adjusts contrast.
3. SCREEN ADJUSTMENT
15
English
3-3. Color
By using the <Color Mode> in the <Color> menu, the adjustment mode can be selected
from standard mode (to set the color temperature and the color restoration), custom
mode (to adjust each color tone, (Red, Green and Blue) and sRGB mode. These modes
allow you to adjust the color settings according to your preference.
<Standard> mode to set the color temperature and the
color restoration
To set the color temperature
→
Set the <Temperature>.
Temperature can be set from 4,000 K to 10,000 K, in 500 K increments.
(Including the 9,300 K default setting.)
To eliminate disparities in color temperature and brightness due to an
irregular video signal output
→
Execute the <Color Correction>.
Color Correction corrects irregular video signal output levels to eliminate
disparities in color temperature and brightness. Every time the PC (graphics
board) and input signal change, execute color correction.
[Adjustment Procedure]
(1) Open a www browser and the Pattern.html in the EIZO Utility Disk.
Then, maximize the window.
(2) Execute the <Color Correction>. All other adjustments are off during the
correction. (The operation takes about 20 to 30 seconds. Do not change the
“Pattern” during the correction.) When color correction is complete, the result
is displayed.
16
3. SCREEN ADJUSTMENT
English
To restore the changed brightness and the color caused by long use to
close to those original ones.
→
Execute the <Color Restoration>.
The changed brightness and the color caused by long use can be corrected and
restored to close to those factory default settings.
[Adjustment Procedure]
(1) Execute the <Color Restoration>. (The operation takes about one minute.)
(2) When color restoration is completed, the original ScreenManager menu is
displayed.
NOTE
• Allow the monitor to stabilize for at least 60 minutes before executing this
function. Otherwise, the warning message “Warming up!” will appear on the
screen.
• Execute this function in every fixed time (ex. 2000 hours usage), so that you
can keep stable brightness and color-tone for a long period.
• The total usage time (in hour) can be checked as the <Information> in the
<Others> menu.
<Custom> mode: to adjust each color, (Red, Green and
Blue)
→ Adjust the <
Gain (p. 33)>, <
Cutoff (p. 33)>
Change the <Color Mode> to <Custom>. The values shown in percentages (%) for
both the Cutoff and Gain are available only as a reference tool.
[Adjustment Procedure]
(1) First, set the monitor to maximum contrast and brightness.
(2) <Temperature> Set the color temperature that is close to the desired color.
(3) Adjust each color to become a uniform black level by using the <Cutoff>
function.
(4) Adjust each color to the desired white level by using the <Gain> function.
(5) Select <Save> and then press the Enter key. (The adjustment data will be lost, if
the monitor is turned off without saving changes).
<sRGB> mode: To select sRGB
→ Select the <sRGB > in < Color Mode>.
During selecting the <sRGB>, color, brightness and contrast cannot be adjusted.
Likewise, Fine Contrast Mode can not be changed by the AUTO/FINE MODE
button.
3. SCREEN ADJUSTMENT
17
English
3-4. Power Save
There are two power save settings. Choose the setting which matches your
environment.
Set the power saving by using <Others> menu.
NOTE
• Do your part to conserve energy, turn off the monitor when you are finished using it.
Complete energy use can only be accomplished by disconnecting the monitor's
power supply cord from the plug receptacle.
To use the PC's power saving system (VESA DPMS (p.
34))
→ Select “ON” in the <PowerManager> menu.
[Procedure]
(1) Set the PC's power saving settings.
(2) Select “ON” in the <PowerManager> menu.
[Power saving system]
PC Signal
On
Power Indicator
Operation
Green
STAND-BY
Blank screen
Green
SUSPEND
Power save (Mode 1)
Flashing Green
Off
Power save (Mode 2)
Yellow
[To return to a normal screen]
Operate the mouse or keyboard.
18
Screen
3. SCREEN ADJUSTMENT
English
To use the Monitor's off timer system
→ Select “On” in the <Off Timer> menu.
Without the PC's power saving system, the off timer allows the monitor to enter a
power save mode after a predetermined amount of time has lapsed.
[Procedure]
Select “On” and press the left/right keys on the control pad to set the “On period”.
(1 to 23 hours)
[To return to a normal screen]
Press any direction of the control pad or to turn the power off then on again to
return to a normal screen.
[Power saving system]
Timer
Screen
On period (1-23H)
Power Indicator
Operation
Green
Last 15 min. in “On period”
Advance notice *1
Flashing Green
“On period” expired
Power save mode
Flashing Yellow
*1
To delay entering the power save mode, press any direction of the control pad
during the advance notice mode. The monitor will continue to operate for an
additional 90 minutes.
3-5. Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
• Adjust the screen using the ScreenManager.
• AUTO/FINE MODE button.
Unlocked function
• Adjustment of contrast and brightness by the shortcut keys.
• BNC/D-Sub Selection button
[To lock]
Press on the AUTO/FINE MODE button while switching on the monitor's power.
[To unlock]
Switch off the monitor’s power, then hold down the AUTO/FINE MODE button once
again and turn the power back on.
3. SCREEN ADJUSTMENT
19
English
3-6. Connecting two PCs to the Monitor
Two PCs can be connected to the monitor through the BNC/D-Sub input connections on
the rear of the monitor.
(Example)
Power Macintosh G3
(Blue&White) /G4
Standard graphics
board
MD-C53A (Optional)
Selecting the Active input
Every time the BNC/D-Sub selection button is pressed, the input changes in order.
[Automatically selecting the priority input signal for screen]
The monitor will automatically detect the input signal of either the BNC or D-Sub
connection for display. In the following cases, the signal given preference will be
displayed automatically.
• When the monitor is turned on.
• Once a priority is selected in the <Input Priority> function, whenever a change of
signal is detected at the selected input, the monitor will switch the input to that signal.
[How to give priority to the input]
(1) Select <Input Priority> in the <Others> menu.
(2) Select <Auto> and set BNC or D-Sub input.
Saving the adjustment data
The adjustment data can be saved for both signals. However, the following adjustment
and setting data can be saved for each input signal (BNC/D-Sub).
<Contrast>, <Fine Contrast>, <Temperature>, <Custom>, <sRGB>, <Signal Filter 1>,
<Signal Filter 2> and <Color Correction>
20
3. SCREEN ADJUSTMENT
English
4. MAKING USE OF USB
(Universal Serial Bus)
This monitor provides a hub which supports the USB standard. When connecting to a
USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.
Required system environment
• PC equipped with USB ports or another USB hub connected to the USB compliant PC
• Windows 98/2000/XP // Mac OS 8.5.1 or later
• EIZO USB Cable (MD-C93)
NOTE
• The USB hub function may not work properly depending on the PC, OS or
peripherals. Please consult the manufacturer of each device about the USB support.
• When the monitor is not on, the peripherals connected to the downstream ports will
not operate.
• Even if the monitor is in a power saving mode, the devices connected to the
monitor’s USB ports (both the upstream and the downstream) will function.
• The followings are procedures for the Windows 98/Me/2000/XP and Mac OS.
Connecting to the USB HUB
1.
Connect the monitor to the PC with the signal cable (See page 11)
first, then turn on the PC.
2.
Connect the upstream port of the monitor to the downstream port of
the USB compliant PC or another hub by using the USB cable.
Upstream port:
Upstream Ports
Connect the USB compliant PC or
another hub using the USB cable.
To Downstream Ports of the PC or
Another Hub
After connecting the USB cable, the USB function can be set up automatically.
4. MAKING USE OF USB (Universal Serial Bus)
21
English
3.
After setting up, the monitor’s USB hub is available for connecting
USB compliant peripherals to the downstream ports of the monitor.
Connecting Examples
Scanner
Digital
Camera
Monitor
PC
Keyboard
<Front port>
Digital Camera
etc.
Mouse
Printer
<Rear port>
Downstream Port
(with a drop down
access lid)
Downstream
Ports
Keyboard
Printer e
Scanner
etc.
Downstream ports:
Connect the cables from USB
compliant peripherals such as a
mouse, keyboard, etc.
The software in the EIZO CRT Utility Disk
For information on the software, refer to the readme.txt in the EIZO CRT Utility Disk.
22
4. MAKING USE OF USB (Universal Serial Bus)
English
5. TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO dealer.
*The bracket < > indicates the function of ScreenManager
Problems
1. No picture
•
Indicator status: Off
•
Indicator status: Green
•
Indicator status: Flashing Green
•
Indicator status: Flashing Yellow
2. Following messages appear. (Error
messages shown below will remain
on the screen for 30 seconds.)
•
“No signal detected” error
message appears.
•
“Out of range” error message
appears. Whenever an error signal
message appears, the signal
frequency will be displayed in red.
(Example)
Points to check with possible solutions
Check that the power cord is correctly
connected.
If the problem persists, turn off the monitor
power for a few minutes, then turn it back on
and try again.
Check the Contrast and Brightness.
Try pressing a key on the keyboard, or clicking
the mouse. (p. 18)
Try pressing the AUTO/FINE MODE button or
control pad or turn the monitor off and then on.
(p. 19)
These messages appear when the signal is not
input correctly, even if the monitor functions
properly.
When the image is displayed correctly after a
short time, it is not a monitor’s problem. (Some
PCs do not output the signal soon after
powering on).
Check that the PC is turned ON.
Check that the signal cable is properly
connected to the PC or graphics board.
Switch the signal input by pressing the
BNC/D-Sub selection button on the front
control panel.
Use the graphics board’s utility software to
change the frequency setting. (Refer to the
manual of the graphics board).
5. TROUBLESHOOTING
23
English
Problems
3. The image vibrates on the screen.
Points to check with possible solutions
Check that the signal cable is correctly
connected to the PC or graphics board.
The monitor may be located close to a device
that is generating a magnetic field. Such devices
include speakers (other than the EIZO optional
i⋅Sound speaker), electric motors, high-voltage
cables, and other monitors. It may be solved by
turning off or moving the interfering device, or
by relocating the monitor.
Use of the <Moiré Reduction> adjustment may
cause a slight vibration. To eliminate the
vibration, set the adjustment level to lower
percentage or 0%.
If the volume level of the EIZO optional i⋅Sound
speaker is too high, it may, in some cases, cause
a slight vibration. To eliminate, turn down the
volume of the speaker.
4. The image is flickering.
Flicker will occur with interlaced scanning or
non-interlaced scanning with a low refresh rate.
All EIZO monitors are capable of reproducing
high refresh rates for non-interlaced scanning.
If a problem occurs when using a non-interlaced
signal, try adjusting the graphics board to
increased the refresh rate (if possible). Refer to
the graphics board manual for information.
5. Moiré patterns appear.
Reduce the moiré using the <Moiré Reduction>.
Change the horizontal and vertical size of the
display area.
Change the selected desktop or wallpaper
pattern to any solid color pattern. For detailed
information in how to change these patterns,
refer to the PC and operating system manual.
24
5. TROUBLESHOOTING
English
Problems
Points to check with possible solutions
6. The characters and images have a
slight shadow on their right side.
Change the mode of <Signal Filter 1>.
Change the refresh rate. Refer to the PC and
graphics card manual for information.
7. The characters and images have a
slight shadow on their right side.
Adjust to decrease the vertical bars at the
<Signal Filter 2>.
8.
Adjust the <Contrast> (Contrast and
Brightness).
Try changing the setting of the fine contrast
mode. (p. 15)
Turn off the monitor, then hold down the down
arrow key while turning on the monitor again.
Some signal timing can be the cause of this
problem. This will change the signal timing and
brighten the screen. If the above operation is
repeated, the screen becomes dark again.
Execute the <Color Restoration>. (p. 17)
The entire screen appears too dark
or bright.
5. TROUBLESHOOTING
25
English
Problems
9. Color is abnormal.
•
The entire screen appears bluish or
reddish.
•
Color purity is not uniform.
•
Misconvergence of colors (red,
green, blue)
Points to check with possible solutions
When the monitor is not fully warmed up, the
screen may look slightly colored, e.g. bluish or
reddish. This phenomenon is due to the
unstableness of the electron gun during its
warm-up period. Wait for about 30 minutes
until the monitor stabilizes in order to gain its
proper color.
Adjust the <Degauss>.
Return the factory default setting by using
<Reset>. Note that all the ScreenManager
parameters will be returned to the factory
default settings. (p. 31)
Adjust the <Uniformity>. (p. 28)
Try adjusting the <Convergence>. The
<Convergence> function adjusts the entire
screen. It is not possible to limit adjustment to
specific screen areas.
Execute the <Color Correction>. (p. 16)
Execute the <Color Restoration>. (p. 17)
10. <Color Correction> does not work
properly.
Color Correction does not work properly when
the input signal level is lower than 0.5 Vp-p or
higher than
1.0 Vp-p
11. <Color Restoration> does not work
properly.
Allow the monitor to stabilize for at least 60
minutes before executing this function.
Otherwise, the warning message “Warming
up!” will appear on the screen. (p. 17)
12. ScreenManager or AUTO/FINE
MODE button does not operate.
The Adjustment Lock is probably on. To
unlock: Turn off the monitor power, then hold
down the AUTO/FINE MODE button once
again and turn the power back on. (p. 19)
13. The Auto sizing function does not
work properly.
The Auto sizing function is intended for use on
the Macintosh and on AT-compatible PC
running Windows. It may not work properly in
either of the following cases. You are running
an AT-compatible PC on MS-DOS (Not
windows). The background color for the “wall
paper” or “desktop” pattern is set to black.
Some signals from graphics card may not
function properly.
26
5. TROUBLESHOOTING
English
Problems
Points to check with possible solutions
14. Two horizontal hairlines are visible
on the screen.
Filaments
Damper Wires
15. Faint black vertical lines are visible
on the screen.
Filaments
Mis-alignment of the
Aperture Grille
These are damper wires.
Damper wires are used to support the CRT's
aperture grille, and are visible as thin dark lines
across the screen.
All EIZO aperture grille type CRTs include two
such horizontal wires. The aperture grille itself
is a grid of taut metal filaments that spans the
entire screen from top to bottom.
The aperture grille may be misaligned. Shock or
vibration during transport may, in some cases,
cause the aperture grille to fall out of alignment.
The problem will appear as one or more faint
black lines across the screen.
If this problem occurs, it may be solved by:
1. Degaussing the screen.
2. Lightly tapping (do not hit) the side of the
monitor.
If neither of these methods works, try executing
the following procedure.
1. Display a bright white field over the area
where the black line(s) appear, with a
black field over the unaffected areas. (Do
this by opening a bright-white window on
top of a black desktop or wallpaper
background. Position the window so that
it just covers the area of misalignment.)
(Refer to left figure)
2. Set brightness and contrast to maximum
values, and keep the display ON until the
problem is corrected.
3. Try tapping the side of the display lightly
to help expedite realignment. The white
field will heat up the misaligned area of the
grille, returning it to proper alignment.
5. TROUBLESHOOTING
27
English
Problems
Points to check with possible solutions
16. USB Function cannot be setup
Check that the USB cable is correctly connected.
Check that the PC and USB compliant. (Please
consult the manufacturer of each device about
USB support.)
When using the Windows 98 or later, check the
BIOS setting of the PC for the USB. (Refer to
the PC manual for details.)
How to adjust the <Uniformity>
Reduce color uniformity errors at the edges of the screen caused by interference from the
geomagnetic field.
[Adjustment Procedure]
(1)
<Standard>
Select the direction the monitor is facing. Select from the
N, NE, E, SE, S, SW, W, NW and Center (no correction).
The “point” may be different depending on the
environment. Select the “Point” that the maximal
brightness and whiteness is uniformed.
If the uniformity is corrected, continue on to (4). If some color patches
remain in the corners after the adjustment, continue on to (2).
(2)
(3)
<Top/Bottom>
Adjust the top/bottom uniformity.
<Top corner> <Bottom corner>
Adjust the uniformity of the for 4 edges of the screen. Be
sure to adjust the “Top corner” first, then adjust the
“Bottom corner”.
Menu
Top corner
Bottom corner
(4)
Top
Control pad
Uniformity
left/right
Left upper
up/down
Right upper
left/right
Left lower
up/down
Right lower
<Save>
Select “Save” and the press the enter button. (If the settings are not saved, all
adjustments will be lost.)
NOTE
• <Reset>
Resets the uniformity function to the factory default setting.
28
5. TROUBLESHOOTING
Bottom
English
6. CLEANING
Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operational lifetime. Clean the cabinet and CRT areas as follows:
NOTE
• Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),
abrasive cleaners, or other strong solvents, as these may cause damage to the
cabinet or CRT.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly onto the cabinet.
CRT Surface
• The CRT surface can be cleaned with a soft cloth, such as cotton or lens paper.
• If necessary, use a moist cloth to remove stubborn stains.
6. CLEANING
29
English
7. SPECIFICATIONS
CRT
55 cm (21 inch) class, 90° deflection Tension Mask with
Anti-Reflective SuperErgoCoat®, 0.25 mm AG Pitch
Horizontal Scan Frequency
30 kHz – 130 kHz (Automatic)
Vertical Scan Frequency
50 Hz – 160 Hz (Automatic)
Recommended Resolution
1600 dots x 1200 lines
Max .Active Display Area*1
400 mm (H) x 298 mm (V) (15.7 (H) x 11.7 (V))
Viewable image size: 498 mm (19.6”)
Power Supply
100-120/200-240 VAC ± 10%, 50/60 Hz, 2.2 A/1.1 A
Power Consumption
Normal/Max: 160 W/ 200 W**
(**With EIZO optional speaker)
PowerManager Mode 1: Less than 10 W
PowerManager Mode 2: Less than 3 W
Input Connector
D-Sub mini 15 pin connector and BNC x 5 (switchable)
Input Signal
Sync
a) Separate, TTL, Positive/Negative
b) Composite, TTL, Positive/Negative
c) Sync on Green, 0.3 Vp-p, Negative
Input Signal
Video
Analog 0.7 Vp-p/75 Ω, Positive
Signal registration
20 signals (Factory preset 2 modes)
Plug & Play
VESA DDC 2B
Dimensions
494 mm (W) x 486 mm (H) x 520 mm (D)
(19.4” (W) x 19.1” (H) x 20.5” (D))
Weight
36.0 kg (79.4 lbs.)
Temperature
Operating: 0 °C ~ 35 °C (32 °F to 95 °F)
Storage: -20 °C ~ 60 °C (-4 °F to 140 °F)
Humidity
30% to 80 % R.H. Non-condensing
Certifications and Standards
100-120 VAC
NRTL/C-TÜV, FCC-B, DHHS, TCO ’99*2, EPA ENERGY
STAR® Program
200-240 VAC
CE, CB, TÜV Rheinland/GS, TCO ’99*2, EPA ENERGY
®
STAR Program, TÜV Eco Circle 2001
*1
Display size can be set by the user through microprocessor control panel. The actual size
displayed can be dependent on the graphics board or PC utilized.
*2
Applicable to gray (standard) color version only.
30
7. SPECIFICATIONS
English
Factory Defaults
Contrast
100%/50%
Moiré Reduction
0%
Signal Filter 1
Mode 1
Signal Filter 2
100%
Color Mode/Temperature
Standard/9300K
PowerManager
On
Off Timer
Disable
Beep
On
Language
English
Input Priority
Auto D-Sub
Fine Contrast
Text
Preset Timing
Resolution
Horizontal
frequency
(kHz)
Vertical
frequency
(kHz)
Interlace
Sync Polarity
H
V
Video Signal
level
VGA
(Text)
720 x 400
31.47
70.09
Non
Negative
Negative
VESA
1600 x 1200
106.25
85.00
Non
Positive
Positive
Analog
0.7 Vp-p/75 Ω
Analog
0.7 Vp-p/75 Ω
mm
Dimensions
(inches)
368.6
(14.51)
494
(19.4)
400
(15.7)
486
(19.1)
298
(11.7)
127
(5.0)
306
( 12.0)
FRONT
42.8 72.5
(1.69) (2.85)
520
(20.5)
SIDE
TOP
7. SPECIFICATIONS
31
English
Pin Assignment
D-Sub mini 15 pin connector
3
4
5
10
15
9
No.
1
2
8
7
Signal
No.
Signal
No.
Signal
1
Red Video
6
Red ground
11
Ground (shorted with
10 pin)
2
Green Video /
Green composite
sync
7
Green ground
12
Data (SDA)
3
Blue video
8
Blue ground
13
4
5
Ground
-
9
10
Ground
14
15
6
14 13 12 11
H.Sync / HV composite
Sync
V.Sync
Clock (SCL)
BNC-Connector
Connector
H.Sync
V.Sync
Green
Red
Blue
Separate sync
H.Sync
V.Sync
Green
Red
Blue
Composite sync
H/V
composite
synce
N/A
Green
Red
Blue
Sync on Green
N/A
N/A
Green
Composite
sync
Red
Blue
Input signal
32
7. SPECIFICATIONS
English
8. GLOSSARY
Color Temperature
Color temperature is a method to measure the white color tone, generally indicated in
degrees Kelvin. At high temperatures the white tone appears somewhat blue, while at
lower temperatures it appears somewhat red. Computer monitors generally give best
performance at high temperature settings.
5,000K: Often used in printing industry.
6,500K: Good for video-image display.
9,300K: Default setting for your EIZO monitor.
Cutoff and Gain
All colors displayed on the screen are produced by the combination of the light's three
primary colors, red, green, and blue. For example, white will be displayed when the
amount of luminescence of red, green and blue is at the almost same rate.
Theoretically, black will be displayed when red, green and blue don't emit light at all.
However, actually, on the screen the amount of luminescence of each color is not zero
and each color emits light slightly. The luminosity of each color at this time is called
cutoff (Black level), and the luminosity of each color on the basis of the cutoff is
called gain.
Convergence
Convergence is the monitor's ability to precisely illuminate specific phosphors and
line them up properly in order to produce pure color.
Degaussing
“Degaussing” refers to the process of removing magnetic-field effects from the
monitor. Operation of the monitor within a magnetic field may adversely effect color
purity. Degaussing can be used to correct the problem.
Moiré Reduction
Moiré refers to an interference pattern of dark wavy lines on the screen. It is not a
defect, but rather an interference phenomenon caused by the relationship between the
phosphor layout and the imaging signal. Moiré is often an indication of a good focus
level. Moiré is particularly noticeable when using a light-gray or every-other-dot
pattern background. Although moiré cannot be eliminated, it can be reduced with the
moiré reduction feature.
8. GLOSSARY
33
English
Resolution
Resolution is expressed as the number of dots (pixels) displayed on the screen.
A larger number of dots produces a more sharply defined (a higher-resolution) image.
Note that for a given screen size the dot size decreases as the number of dots
increases: a 640 x 480 (dot x line) resolution uses larger pixels than a 1024 x 768
resolution. The display size of a given font therefore varies according to the
resolution. Higher resolutions allow you to display more information on the screen.
sRGB (Standard RGB)
“International Standard for Red, Green, and Blue color space” A color space was
defined with the aim of the color matching between applications and hardware
devices, such as monitors, scanners, printers and digital cameras. As a standard
default space, sRGB allows Internet users to closely match colors.
Uniformity
The uniformity is the purity of the color when a white screen is displayed on screen.
Some monitors have blue or pink tinted areas that exhibit poor white uniformity.
Some monitors have some brighter and darker areas, then this is an indication of
bright uniformity error.
VESA DPMS
The acronym VESA stands for “Video Electronics Standards Association,” and DPMS
stands for “Display Power Management Signaling.” DPMS is a communication
standard that PCs and graphics boards use to implement power savings on the
monitor side.
34
8. GLOSSARY
[Applicable to gray (standard color version only).]
Congratulations!
You have just purchased a TCO’99 approved and labelled product!
Your choice has provided you with a product developed for
professional use. Your purchase has also contributed to reducing
the burden on the environment and also to the further development
of environmentally adapted electronics products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an established method for encouraging
the adaptation of goods and services to the environment. The main problem, as far as computers
and other electronics equipment are concerned, is that environmentally harmful substances are
used both in the products and during their manufacture. Since it is not so far possible to
satisfactorily recycle the majority of electronics equipment, most of these potentially damaging
substances sooner or later enter nature.
There are also other characteristics of a computer, such as energy consumption levels, that are
important from the viewpoints of both the work (internal) and natural (external) environments.
Since all methods of electricity generation have a negative effect on the environment (e.g. acidic
and climate-influencing emissions, radioactive waste), it is vital to save energy. Electronics
equipment in offices is often left running continuously and thereby consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’99 scheme which provides for international
and environmental labelling of personal computers. The labelling scheme was developed as a
joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska
Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens
Energimyndighet (The Swedish National Energy Administration).
Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission
of electric and magnetic fields, energy consumption and electrical and fire safety.
The environmental demands impose restrictions on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among
other things. The product must be prepared for recycling and the manufacturer is obliged to have
an environmental policy which must be adhered to in each country where the company
implements its operational policy.
The energy requirements include a demand that the computer and/or display, after a certain
period of inactivity, shall reduce its power consumption to a lower level in one or more stages.
The length of time to reactivate the computer shall be reasonable for the user.
Labelled products must meet strict environmental demands, for example, in respect of the
reduction of electric and magnetic fields, physical and visual ergonomics and good usability.
You will find a brief summary of the environmental requirements met by this product on the
right. The complete environmental criteria document may be ordered from:
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO’99 approved and labelled products may also be obtained
via the Internet, using the address: http://www.tco-info.com/
Environmental Requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings.
Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in
a computer casing can consist of flame retardant substances. Most flame retardants contain
bromine or chloride, and those flame retardants are chemically related to another group of
environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the
PCBs are suspected of giving rise to severe health effects, including reproductive damage in
fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have
been found in human blood and researchers fear that disturbances in foetus development may
occur.
The relevant TCO’99 demand requires that plastic components weighing more than 25 grams
must not contain flame retardants with organically bound bromine or chlorine. Flame
retardants are allowed in the printed circuit boards since no substitutes are available.
Cadmium**
Cadmium is present in rechargeable batteries and in the colour-generating layers of certain
computer displays. Cadmium damages the nervous system and is toxic in high doses.
The relevant TCO’99 requirement states that batteries, the colour-generating layers of display
screens and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches. It damages the nervous system
and is toxic in high doses.
The relevant TCO’99 requirement states that batteries may not contain any mercury. It also
demands that mercury is not present in any of the electrical or electronics components
associated with the labelled unit.
CFCs (freons)
The relevant TCO’99 requirement states that neither CFCs nor HCFCs may be used during
the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing
printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the
stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks
of skin cancer (malignant melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the
nervous system and in higher doses, causes lead poisoning.
The relevant TCO’99 requirement permits the inclusion of lead since no replacement has yet
been developed.
* Bio-accumulative is defined as substances which accumulate within living organisms.
** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan T966
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Hinweis zur Ergonomie :
Dieser Monitor erfüllt die Anforderungen an die Ergonomie nach EK1-ITB 2000 mit dem
Videosignal, 1600 Punkte × 1200 Zeilen, RGB analog, 0,7 Vp-p und mindestens 85,0 Hz
Bildwiederholfrequenz, non interlaced. Weiterhin wird aus ergonomischen Gründen empfohlen,
die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeit,
Augenbelastung bei zu geringem Zeichenkontrast.)
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland
zusammen mit dem Partner von Roll MBB Recycling GmbH.Dort werden die Geräte in ihre
Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden. Um einen Abholtermin
zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende Rufnummer:
02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse:
www.eizo.de.
Hinweis
Die boldröhre dieses Monitors ist frei von Cadmium.
EIZO NANAO CORPORATION
153 Shimokashiwano, Matto, Ishikawa 924-8566 Japan
Phone: + 81 76 277 6792 Fax: + 81 76 277 6793
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: +1 562 431 5011 Fax: +1 562 431 4811
http://www.eizo.com/
First Edition-July, 2002
Version A
(MA-21D5-EU)