Clarke C2K-1800HSV Operator`s manual

C2K Series
230V 50Hz
Polisher
UK
Operator's
Manual
READ THIS BOOK
CAUTION: Read the Operator's Manual before using the appliance.
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If your
operator cannot read English, have this manual explained fully before attempting to operate this
machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 70199A 1/02
CLARKE TECHNOLOGY
Printed in the U.S.A.
CONTENTS OF THIS BOOK
Operator Safety Instructions ............................................................................................... 3
Machine Introduction .......................................................................................................... 4
Accessories ....................................................................................................................... 5
Machine Specifications ...................................................................................................... 6
How To Prepare the Machine for Operation ......................................................................... 7
How to Install the Brush or Pad Driver .......................................................................... 7
How to Adjust the Handle ............................................................................................. 7
Instructions for Connection to Power Supply & Elect. Ground, 230 V ................................. 8
How to Operate the Machine .............................................................................................. 9
How To Start/Stop The Machine ................................................................................... 9
How to Control the Machine ......................................................................................... 9
Maintenance ...................................................................................................................... 9
Section II Parts and Service Manual
Maintenance .................................................................................................................... 12
Assembly Drawing ........................................................................................................... 14
Assembly Parts List ................................................................................................. 15
Assembly Drawing ........................................................................................................... 16
Assembly Parts List .................................................................................................. 17
Motor Assembly Drawing & Parts List .............................................................................. 18
Gearbox Assembly Drawing & Parts List ......................................................................... 19
Motor Assembly Drawing & Parts List .............................................................................. 20
Gearbox Assembly Drawing & Parts List ......................................................................... 21
Motor Assembly Drawing and Parts List ........................................................................... 22
Gearbox Assembly Drawing and Parts List ...................................................................... 23
Wiring Diagrams .............................................................................................................. 24
Page -2 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
OPERATOR SAFETY INSTRUCTIONS
WARNING
AVERTISSEMENT
ADVERTENCIA
DANGER means:
Severe bodily injury or death can occur to you or other personnel if the DANGER
statements found on this machine or in this Owner's Manual are ignored or are not
adhered to. Read and observe all DANGER statements found in this Owner's
Manual and on your machine.
WARNING means:
Injury can occur to you or to other personnel if the WARNING statements found on
your machine or in this Owner's Manual are ignored or are not adhered to. Read
and observe all WARNING statements found in this Owner's Manual and on your
machine.
CAUTION means:
Damage can occur to the machine or to other property if the CAUTION statements
found on your machine or in this Owner's Manual are ignored or are not adhered to.
Read and observe all CAUTION statements found in this Owner's Manual and on
your machine.
DANGER:
Failure to read the Owner's Manual prior to operating or attempting any service or maintenance
procedure to your machine could result in injury to you or to other personnel; damage to the
machine or to other property could occur as well. You must have training in the operation of this
machine before using it. If your operator(s) cannot read English, have this manual explained
fully before attempting to operate this machine.
DANGER:
To reduce the risk of fire, use only commercially available floor cleaners and waxes intended for
machine application. Do not use with flammable liquids.
DANGER:
Risk of explosion. Floor sanding can result in an explosive mixture of fine dust and air. To
reduce risk of explosion, use floor sanding machine only in well ventilated area.
DANGER:
Operating a machine that is not completely or fully assembled could result in injury or property
damage. Do not operate this machine until it is completely assembled. Inspect the machine
carefully before operation.
DANGER:
Electrocution could occur if maintenance and repairs are performed on a unit that is not disconnected from the power source. Disconnect the power supply before attempting any maintenance
or service. Always remove the electrical plug from the electrical outlet before changing the brush,
pad or other attachment and before leaving the machine.
DANGER:
Using a machine with a damaged power supply cord could result in an electrocution. Regularly
examine the power supply cord for damage, such as cracking or ageing. Do not use the machine if the power supply cord is damaged. Only replace the power supply cord with the type
specified in the instruction manual.
WARNING:
Maintenance and repairs performed by unauthorized personnel could result in damage or injury.
Maintenance and repairs must be performed by authorized personnel only. Keep all fasteners
tight. Keep adjustments according to specifications.
WARNING:
This appliance is for dry use only and is not to be used or stored outdoors in wet conditions.
WARNING:
Always use a three-wire electrical system connected to the electrical ground. For maximum
protection against electric shock, use a circuit that is protected by a ground fault interrupter. Only
use the socket outlet on the appliance for purposes specified in the instruction manual.
WARNING:
To prevent damage to the power supply cord, do not let the brush, pad, pad driver or wheels
touch the power supply cord when the machine is running. Always lift the cord over the machine.
Do not pull the power supply cord to move the machine.
WARNING:
Operating a machine without observing all labels and instructional information could result in
injury or damage. Read all machine labels before attempting to operate. Make sure all of the
labels and instructional information are attached or fastened to the machine. Get replacement
labels and decals from your authorized distributor.
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
Page - 3 -
OPERATOR SAFETY INSTRUCTIONS (cont.)
WARNING:
Use of this machine as a step or furniture could result in injury or damage. Do not use this
machine as a step or furniture. Do not ride on this machine.
WARNING:
To avoid injury keep hands, feet and loose clothing away from all moving parts of this
machine.
WARNING:
Injury to operator or bystanders could occur if an abrupt change in floor surface texture is
encountered when using this machine. Abrupt change in floor surface texture can cause a
sudden pulling motion by this machine. This sudden pulling motion can result in loss of
control of the machine which could injure the operator or bystanders. Avoid motions that
could cause machine to cross from a smooth floor surface to a carpeted or rough texture
floor surface Avoid motions that could allow the machine to come in contact with low
obstacles, such as floor electrical outlets, door stops or entry molding, etc.
WARNING:
Water solutions or cleaning materials used with this type of machine can leave wet areas
on the floor surface. These areas can cause a dangerous condition for the operator or
other persons. Always put CAUTION signs near the area being cleaned.
WARNING:
Any alterations or modifications of this machine could result in damage to the machine or
injury to the operator or other bystanders. Alterations or modifications not authorized by
the manufacturer voids any and all warranties and liabilities.
CAUTION:
The machine is heavy. Get assistance before attempting to transport or move it.
CAUTION:
This appliance is not suitable for picking up hazardous dust.
MACHINE INTRODUCTION
The CLARKE TECHNOLOGY C2K Series
The ALTO C2K Series are floor maintaining machines that can be used for polishing, spraying, buffing, stripping and
shampooing. The machines can be used on wood, vinyl, terrazzo or cement floors. With the shampoo brush, the
machines can be used to clean carpet and with the sanding disc they can be used to sand floors.
This appliance is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, offices and
rental businesses.
Page -4 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
ACCESSORIES
The following accessories are available.
1. Polishing and waxing brushes.
2. Brushes with natural or synthetic bristles for
scrubbing.
6. Brushes with metal or wood backs and with
holes to let the solution flow through.
7. Solution tank.
3. Brushes with steel wire bristles for concrete.
8. Sanding discs for wood floors.
4. Synthetic pad holders.
9. Spray Buff Accessory.
5. Synthetic pads for polishing, scrubbing,
stripping and spray buffing.
10. Grinding disk for concrete.
Model
C2K Code Number
Solution Tank Assembly
Spray Buff Attachment
Weight Kit
Polyproplene Scrub Brush
High Speed Pad Driver
Perma Grip Pad Driver
Super Grip Drive Pad
Standard Pad Driver
Sanding Disc Driver (Wood)
Abrasive Coated Tynex
Steel Wire Brush (Concrete)
Capture (Carpet) Scrub Brush
Nylon Brush (Carpet)
Grinding Disk Assembly
Dust Skirt
16
01221A
50026A
18
01222A
50026A
160
01223A
50026A
180
01224A
50026A
200
01225A
50026A
1600
01226A
50026A
1800
01227A
50026A
---------51704A
---------51706A
---------51704A
---------51706A
---------51707A
10086A
51704A
10086A
51706A
53159A
37007A
50864A
--------------------410963
------------------------------10087A
53157A
37009A
50865A
--------------------410984
----------------------------10088A
53159A
37007A
50864A
----------51443A
410963
----------------------------10087A
53157A
37009A
50865A
----------51445A
410984
----------------------------10088A
53156A
37011A
50866A
----------51446A
480924
------------------------------10089A
53159A
37007A
50864A
450214
51443A
410963
----------51498A
450212
10087A
53157A
37009A
50865A
460215
51445A
410984
11405A
51701A
500212
10088A
Model
C2K Code Number
Solution Tank Assembly
Spray Buff Attachment
Weight Kit
Polyproplene Scrub Brush
High Speed Pad Driver
Perma Grip Pad Driver
Super Grip Drive Pad
Standard Pad Driver
Sanding Disc Driver (Wood)
Abrasive Coated Tynex
Steel Wire Brush (Concrete)
Capture (Carpet) Scrub Brush
Nylon Brush (Carpet)
Grinding Disk Assembly
Dust Skirt
2000
01228A
50026A
--------10086A
51707A
--------53156A
37011A
50866A
----------51446A
480924
11406A
--------------------10089A
1600HS
01229B
50026A
440570
---------51704A
53154A
53159A
37007A
50864A
------------------------------------------------------------10087A
1800HS
01230B
50026A
440570
---------51706A
53153A
53157A
37009A
50865A
------------------------------------------------------------10088A
2000HS
01231B
50026A
440570
---------51707A
17518A
53156A
37011A
50866A
-----------------------------------------------------------10089A
1600DS
01232B
50026A
440570
10086A
51704A
53154A
53159A
37007A
50864A
----------------------------------------51498A
----------10087A
2000DS
01233B
50026A
440570
10086A
51707A
17518A
53156A
37011A
50866A
------------------------------------------------------------10089A
1800HSV
09234B
------------------------51706A
53153A
52157A
37009A
50865A
------------------------------------------------10088A
WARNING: Use only brushes and accessories supplied by the manufacturer. The
use of other brushes and accessories may impair safety. Large diameter brushes
provided specifically for dry buffing are not intended for general polishing.
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
Page - 5 -
Machine Specifications
Model
Code Number
Voltage (V)
Frequency (Hz)
Current (A)
Power (kW)
Brush Diameter (cm)
Block Diameter (cm)
Brush Speed (rpm)
Cord Length (m)
Weight (kg)
Noise (dBA)
Vibration (m/s2)
C2K-
16
01221A
230
50
8
0.56
41
36
204
15
40
<70
<2.5
18
01222A
230
50
8
0.56
46
41
204
15
40
<70
<2.5
160
01223A
230
50
8
0.75
41
41
204
15
40
<70
<2.5
180
01224A
230
50
8
0.75
46
46
204
15
40
<70
<2.5
Model
Code Number
Voltage (V)
Frequency (Hz)
Current (A)
Power (kW)
Brush Diameter (cm)
Block Diameter (cm)
Brush Speed (rpm)
Cord Length (m)
Weight (kg)
Noise (dBA)
Vibration (m/s2)
C2K-
1600HS
01229B
230
50
8
1.1
41
36
407
15
42
<70
<2.5
1800HS
01230B
230
50
8
1.1
46
41
407
15
42
<70
<2.5
2000HS
01231B
230
50
8
1.1
51
36
407
15
42
<70
<2.5
1800HSV
09234B
230
50
9
1.1
46
41
407
15
44
<70
<2.5
Model
Code Number
Voltage (V)
Frequency (Hz)
Current (A)
Power (kW)
Brush Diameter (cm)
Block Diameter (cm)
Brush Speed (rpm)
Cord Length (m)
Weight (kg)
Noise (dBA)
Vibration (m/s2)
C2K-
1600
01226A
230
50
8
1.1
41
36
204
1800
01227A
230
50
8
1.1
46
41
204
15
42
<70
<2.5
2000
01228A
230
50
8
1.1
51
46
204
15
42
<70
<2.5
1600DS
01232B
230
50
8
1.1
41
36
180/320
15
43
<70
<2.5
Page -6 -
42
<70
<2.5
200
01225A
230
50
8
0.75
51
51
204
15
40
<70
<2.5
2000DS
01233B
230
50
8
1.1
51
46
180/320
15
15
43
<70
<2.5
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
HOW TO PREPARE THE MACHINE FOR
OPERATION
WARNING: Always remove the electrical
plug from the electrical outlet before
installing or changing the pad or brush.
How To Install The Brush Or Pad Driver
To install the brush or pad driver, follow this
procedure:
1. Put the handle in the vertical position.
2. To lock the handle, push the locking lever
down.See figure 1.
Figure 1
3. Tilt the machine backward until the handle is on
the floor. See figure 2.
4. Put one foot on each side of the machine. See
figure 2.
5. Align the lugs (1) on the locking plate into the
pad driver adapter openings (2). See figure 3.
6. To lock the brush or pad into position, turn the
brush or pad driver clockwise.
7. Turn the brush or pad counterclockwise to
unlock and remove the brush.
Figure 2
8. Lift the machine to the vertical position.
NOTE: To prevent damage to the brush or pad
driver, remove the accessory while not in use.
Keep the brush in a cool, dry place.
How To Adjust The Handle
To adjust the handle, follow this procedure:
1. The locking lever is on the lower part of the
handle tube. Use your foot to lift the lever.
See figure 1.
2.
Lower the handle to the best operating position.
NOTE: For the best operating position, keep your
back straight, bend only your arms.
Figure 3
1. The lugs.
2. The drive adpater openings.
3. Using your foot, push the locking lever down.
4. Hold the handle against your body for the best
control.
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
Page - 7 -
230 VOLT MACHINES Instruction for
connection to the power supply and the
electrical ground
.
UK Plug
CAUTION: This machine will operate
only on the AC frequency and electrical
voltage shown on the nameplate. Make sure
you have the correct frequency and voltage
before connecting the power cord to an
outlet.
This machine must be connected to the electrical
ground to protect the operator from electric
shock. The machine has a power cord with two
main conductors and one earthing conductor.
Connect the plug to the type of receptacle shown
in figure 4. The green and yellow conductor in the
cord is the ground wire. Never connect this wire
to any terminal other than the ground terminal.
UK Socket
(UK and Ireland)
Figure 4
WARNING: Always use this machine
with an AC three-conductor electrical
system connected to the electrical
ground. Replace any worn, cut, or
damaged cords. Replace any damaged
plugs, receptacles, or connector
bodies. Do not move the machine over
an electrical cord. Always lift the cord
over the machine.
EXTENSION CORDS
Use only an approved extension cord with two
main conductors and one earthing conductor.
The machine has a power cord with wire size 1.5
mm2.
WARNING: If you use an extension
cord, use an extension cord with minimum
wire size 1.5mm2. Do not use an extension
cord longer than 15 meters. Do not join two
extension cords.
WARNING: Do not cut, remove, or
break the ground terminal. Do not try to fit a
three- terminal plug into a receptacle or
connector body that does not fit the plug.
If the receptacle or connector body does not
fit the plug, see your Authorized person to
make the connection.
Page -8 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
HOW TO OPERATE THE MACHINE
1
How To Start/Stop The Machine
WARNING:
Never start a polisher when
the handle is in the vertical
position.
The following step applies to the C2K-1600DS and C2K2000DS only:Select high or low speed with the switch
located on the motor cover. Moving the switch lever up
selects high speed. Moving the switch lever down
selects low speed.
The following steps apply to all C2K series:
The switch to start and stop the machine is activated
by the interlock button (1) and the levers (2) under the
handle grips. See figure 5.
To start the machine, follow this procedure:
2
2
Figure 5
1. Lower the handle
2. Lock the handle in the best position for operation.
NOTE: Make sure you hold the handle with both
hands.
3. Push the interlock button (1), and apply pressure to
the levers (2). See figure 5.
How To Control The Machine
NOTE: Make sure you hold the handle with both
hands.
The side to side movement of the machine is controlled
by raising the handle and pressing down on the handle.
To move the machine to the left, press down on the
handle slightly. To move the machine to the right, raise
the handle slightly.
MAINTENANCE
WARNING: Maintenance must be done
by authorized personnel
only.
Maintenance Instructions
Return the machine to a Clarke Technology Authorized
Service Location every 12 months for maintenance
inspections.
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
Page - 9 -
NOTES
Page -10 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
C2K Series
230V
Section II
Parts and Service Manual
(70199A)
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
Page - 11 -
MAINTENANCE
WARNING: Maintenance must be done by
authorized personnel only.
CAUTION: Keep all adjustments according
to specifications.
Maintenance Instructions
Return the machine to a Clarke Technology Authorized
Service Location every 12 months for maintenance
inspections.
Switches
WARNING: All electrical repairs must be
done by authorized personnel only. The
machine must be tested after electrical
repairs to make sure it is safe to operate.
Disconnect the electrical plug from the
electrical outlet before doing any
electrical repairs.
The start and stop switch has an interlock which prevents the contacts from being closed. If any part of the
switch is not operating, replace the part. If any part of the
electrical system of the machine is not operating or is
damaged, replace the part. Make sure all connections
are tight. Return the machine to the Clarke Technology
Service Branch or a Clarke Technology Authorized
Service Center for electrical repairs or testing.
Maintenance Of The Motor
Induction type motors do not require motor brushes.
C2K-1600DS and C2K-2000DS require motor brushes.
If repairs to the gear unit or motor are needed, do not
disassemble the gears and motor. Return the machine
to the nearest Clarke Technology Service Branch or
Clarke Technology Authorized Service Center.
For safe operation, and longer life to your Clarke Technology product, use only Clarke Technology parts.
NOTE: The grease (503802) for the gear box needs
to be changed every year. The C2K-1600, C2K1600DS C2K-1600HS, C2K-1800, C2K 1800HS, C2K2000, C2K-2000DS, C2K-2000HS require 8 oz. of
grease. All other C2K series require 9 oz. of grease.
Page -12 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
NOTES
CLARKE TECHNOLOGY Operator's Manual - C2K Series 230V
Page - 13 -
CLARKE TECHNOLOGY
C2K-16, C2K-18, C2K-160, C2K-180, C2K-200,
C2K-1600, C2K-1800, C2K-2000, C2K-160HS, C2K-180HS, C2K-200HS
Assembly Drawing 2/01
1
2
5
4
3
4
6
3
7
10
1
8
13
31
21
38
1
9
11
10
41
22
43
20
24
19
17
29
23 1
44
16
37
14
26
18
42
30
25
26
22
28
25
15
32
1
23
27
33
24
34
36
Page -14 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series
CLARKE TECHNOLOGY
C2K-16, C2K-18, C2K-160, C2K-180, C2K-200,
C2K-1600, C2K-1800, C2K-2000, C2K-1600HS, C2K-1800HS, C2K-2000HS
Assembly Drawing Parts List 2/01
Ref. Part No. Description
1
2
3
4
5
6
7
8
9
10
11
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
36
37
38
41
42
43
44
NI
85383A Screw, 10-32 x 3/4
50779A Handle, Front
50798A Lever, Switch
50820A Spring, Extension
50806A Button, Interlock
40109A Switch
50799A Interlock, Main
50821A Spring, Compression
50780A Handle, Rear
920722 Nut, 10-3 ESNA
962957 Screw
50871A Cord, Interconnect
461404 Cam, Locking (included w/42)
925592 Roll Pin, ¼ (included w/42)
441301 Bolt, Locking Cam (included w/42)
980349 Washer, Wear Cam
50791A Arm Link, RH
50781A Clamp, Handle
50792A Arm Link, LH
980645 Washer, Flat 3/8
920342 Nut, 3/8 -16 ESNA
87035A Washer, Fender #10 SS
50793A Wheel, 5"
87050A Washer, 5/8 Nylon
50794A Bushing, Nylon
80087A Screw, 3/8 -16 x 6
57120A Plug, Button
50993A Motor (16, 18)
44638A Motor (160, 180, 200)
50879A Motor (1600, 1800, 2000)
50880A Motor (1600HS, 1800HS, 2000HS)
50872A Gearbox (16, 18, 160, 180, 200)
50881A Gearbox (1600, 1800, 2000)
51344A Gearbox (1600HS, 1800HS, 2000HS, 1800HSV)
50822A Cover, Motor (16, 18, 160, 180, 200)
50823A Cover, Motor (1600, 1800, 2000, 1600HS,
1800HS, 2000HS)
50790A Frame, Main
50785A Shield, Brush (16, 160, 1600)
50786A Shield, Brush (18, 180, 1800)
50787A Shield, Brush (200, 2000)
51218A Shield (1800HSV)
50782A Bumper, (16, 160, 1600)
50783A Bumper, (18, 180, 1800)
50784A Bumper, (200, 2000)
80098A Screw, 5/16-18 x 21/8
50796A Bushing, Cord
50795A Tube, Handle
50870A Cord Assembly
441401 Cam Assembly (includes 14,15, 16)
747553 Strain Relief
77378A Label
82100A Locknut
CLARKE TECHNOLOGY Operator's Manual - C2K Series
Qty.
12
1
2
2
1
2
1
1
1
7
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
(1)
1
1
1
Page - 15 -
CLARKE TECHNOLOGY
C2K-1600DS and C2K-2000DS
Assembly Drawing 2/01
1
2
3
4
5
4
6
7
3
9
10
13
1
41
8
57
10
54
42
38
21 22
43
45
20
16
19
17
44
49
24
23 1
37
14
46
26
50
31
18
51
25
26
47
22
28
15
11
25
12
53
52
1
23
12
30
32
27
11
24
33
1 56
30a
56
55
10
48
34
36
29 10
Page -16 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series
CLARKE TECHNOLOGY
C2K-1600DS and C2K-2000DS
Assembly Parts List 2/01
Ref. Part No. Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
30a
31
32
33
34
36
37
38
41
42
43
44
45
46
47
48
49
50
51
52
54
55
56
57
NI
NI
85383A
50779A
50798A
50820A
50806A
40109A
50799A
50821A
50780A
920722
40139A
40140A
50875A
461404
925592
441301
980349
50791A
50781A
50792A
980645
920248
87035A
50793A
87050A
50794A
80087A
57120A
50825A
51342A
51343A
50824A
50790A
50785A
50787A
50782A
50784A
80098A
50796A
50795A
85517A
70151A
50877A
51345A
751321
34261A
80201A
747553
70218A
77378A
441401
30605A
50870A
47201A
98458A
962957
82100A
51058A
Screw, 10-32 x 3/4
Handle, Front
Lever, Switch
Spring, Extension
Button, Interlock
Switch
Interlock, Main
Spring, Compression
Handle, Rear
Nut, 10-32 ESNA
Blue Wire Assembly
Brown Wire Assembly
Cord, Interconnect
Cam, Locking (included w/51)
Roll Pin, ¼ (included w/51)
Bolt, Locking Cam (included w/51)
Washer, Wear Cam
Arm Link, RH
Clamp, Handle
Arm Link, LH
Washer, Flat 3/8
Nut, 3/8 -16 ESNA
Washer, Fender #10 SS
Wheel, 5"
Washer, 5/8 Nylon
Bushing, Nylon
Screw, 3/8 -16 x 6
Plug, Button
Bracket
Motor/Gearbox (includes #30a)
Gearbox (included w/#30)
Cover, Motor
Frame, Main
Shield, Brush (1600)
Shield, Brush (2000)
Bumper, (1600)
Bumper, (2000)
Screw, 5/16-18 x 21/8
Bushing, Cord
Tube, Handle
Screw
Label
Switch
Circuit Breaker (Includes #45)
Boot (included w/#44)
Light
Clip
Strain Relief
Label, (High - Low)
Label
Cam Asm (includes 14,15,16)
Baffle
Cord Asm. (w/ strain Relief)
Filter
Bushing
Screw
Locknut
Baffle
CLARKE TECHNOLOGY Operator's Manual - C2K Series
Qty.
12
1
2
2
1
2
1
1
1
10
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
(1)
1
1
1
1
1
1
4
1
1
2
1
1
1
(1)
1
1
1
1
1
(1)
1
1
1
2
2
1
1
Page - 17 -
CLARKE TECHNOLOGY
C2K-16, C2K-18, C2K-160, C2K-180 and C2K-200
230V - 50 Hz Motor Assembly Drawing & Parts List 2/01
Note: If your machine has motor #44638A refer to this
drawing for service part replacement.
13
1
2
8
3
9
10
11
12
14
15
16
7
4
18
17
6
Ref. Part No.
1
2
3
4
6
7
8
9
58030A
52018A
52019A
54330A
53976A
50400A
56461A
902550
Description
Ref.
Qty.
Screw #10-32 x.31
Capacitor Case
Start Capacitor
Gasket, Capacitor Case
Stator Frame Asm
Rotor and Shaft Assembly
Centrifugal Switch Asm. (50 Hz)
Bearing
2
1
1
1
1
1
1
1
10
11
12
13
14
15
16
17
18
Part No.
58673A
58032A
54713A
53523A
58911A
58912A
58034A
50691A
58031A
Description
Washer
Stationary Switch
Stationary Switch Insulation
Bracket Opp. Shaft End
Terminal Board Asm.
Terminal Board
Screw #18-32 X .50
Bolt, .250-28 x 6.75
Screw, #8-32 x .38
230V Motor
Electrical Schematic
L1
L2
Page -18 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series
Qty.
1
1
1
1
1
1
2
4
2
CLARKE TECHNOLOGY
C2K-16, C2K-18, C2K-160, C2K-180 and C2K-200
Gearbox Assembly Drawing & Parts List 1/02
Note:
If your machine has gearbox #50872A refer to this
drawing for service part replacement.
2
3
4
5
6
7
8
9
10
11
4
12
4
Ref.
Part No.
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
19
80141A
56922A
902606
58513A
53524A
962794
54858A
902736
58314A
442473
902737
52020A
58312A
902573
Description
Screw, Socket Hd. Cap
Plate, Retainer
Bearing
Spacer, Sleeve
Endshield
Screw 10-24" x 1"
Cover, Housing
Bearing
Retainer
Coupling
Gear, Pinion
Bearing, Needle
Cage
Gear, Idler
Shaft
Bearing
Housing, Drive
Qty.
6
1
3
1
1
6
1
1
1
1
1
4
1
2
2
1
1
14
15
16
17
14
18
19
CLARKE TECHNOLOGY Operator's Manual - C2K Series
Page - 19 -
CLARKE TECHNOLOGY
C2K-1600, C2K-1800, C2K-2000, C2K-1600HS, C2K-1800HS and C2K-2000HS
Motor Assembly Drawing & Parts List 1/02
Note:
If your machine has motor #50879A or #50880A refer
to this drawing for service part replacements.
1
2
3
4
5
"HS"
machines
Page -20 -
50880A
50879A
Ref.
Part No.
Part No.
Description
Qty
1
2
3
4
5
50861A
40153A
40154A
40155A
40156A
50861A
51054A
51055A
50862A
50863A
Ball Bearing
Centrifugal and Switch
Rotor
Capacitor, Start
Capacitor, Run
1
1
1
1
1
CLARKE TECHNOLOGY Operator's Manual - C2K Series
CLARKE TECHNOLOGY
C2K-1600, C2K-1800, C2K-2000, C2K-1600HS, C2K-1800HS and C2K-2000HS
Gearbox Assembly Drawing & Parts List 1/02
Note:
If your machine has gearbox #50881A or #51344A
refer to this drawing for service part replacement.
50881A
Ref
1
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Part No.
80141A
902606
58520A
50852A
962794
54858A
902736
58314A
442473
902737
N/A
58312A
902573
Description
Screw, Socket Hd. Cap
Bearing, Ball
Spacer, Sleeve
Endshield
Screw 10-24" x 1"
Cover, Housing
Bearing
Retainer
Coupling
Gear, Pinion
Bearing, Needle
Cage
Gear, Idler
Shaft
Bearing, Ball
Housing, Drive
CLARKE TECHNOLOGY Operator's Manual - C2K Series
Qty.
6
3
1
1
6
1
1
1
1
1
6
1
3
3
1
1
51344A
("HS")
Qty.
6
3
1
1
6
1
1
1
1
1
4
1
2
2
1
1
Page - 21 -
CLARKE TECHNOLOGY
C2K-1600DS and C2K-2000DS
230V Motor Assembly Drawing & Parts List 1/02
Note: If your machine has motor/gearbox #51342A
refer to this drawing for service part replacement.
1
1
2
3
15
4
10
14
6
6
5
20
19
6
6
7
16
18
8
9
9
7
9
17
NOTE: ‹ indicates a change has been
made since the last publication of this
manual.
Ref
1
2
3
4‹
5
6
7
8
9
10
11
12
13
14‹
15‹
16
17
18
19
20
21
Part No.
50717A
N/A
56282A
46105A
962399
448396
40819A
40411A
962310
980608
58057A
902550
40323A
58056A
831102
55648A
980076
55647A
59607A
46736A
51343A
Page -22 -
Description
Thru-Bolt
Commutator Bracket
Hex Nut
Rectifier
Screw
Spring (Included with #8)
Brush Asm., (Included w/#8)
Brush Board Asm. (incls. #'s 6,7,16,18,19)
Screw
#8 Flat Washer
Stator Frame
Bearing-Upper (Included w/#13)
Armature Asm. (Includes #12)
Strain Relief
Bushing
Red Lead (included w/#8)
Wave Washer
Yellow Lead (included w/#8)
Varistor (Included w/#8)
Speed Control
Gearbox
Qty.
2
1
1
1
1
(4)
(4)
1
4
1
1
(1)
1
1
1
1
1
1
(1)
1
(1)
11
12
13
21
CLARKE TECHNOLOGY Operator's Manual - C2K Series
CLARKE TECHNOLOGY
C2K-1600DS and C2K-2000DS
Gearbox Assembly Drawing & Parts List 1/02
Note: If your machine has gearbox #51343A
refer to this drawing for service parts.
18
17
16
4
11
4
12
10
8
13
13
14
15
9
7
6
5
4
3
1
2
Ref
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Part No.
80141A
56922A
902606
58520A
53539A
962794
54858A
902736
58314A
442473
902737
N/A
58312A
902573
CLARKE TECHNOLOGY Operator's Manual - C2K Series
Description
Screw, Socket Hd. Cap
Retainer, Bearing
Bearing, Ball
Spacer, Sleeve
Endshield
Screw 10-24" x 1"
Cover, Housing
Bearing
Retainer
Coupling
Gear, Pinion
Bearing, Needle
Cage
Gear, Idler
Shaft
Bearing, Ball
Housing, Drive
Qty.
6
1
3
1
1
6
1
1
1
1
1
4
1
2
3
1
1
Page - 23 -
CLARKE TECHNOLOGY
C2K-16, C2K-18, C2K-160, C2K-180, C2K-200,
C2K-1600, C2K-1800, C2K-2000, C2K-160HS, C2K-180HS, C2K-200HS
Wiring Diagram 230V - 50Hz 3/00
CLARKE TECHNOLOGY
C2K-1600DS and C2K-2000DS
Wiring Diagram 230V 3/00
CLARKE TECHNOLOGY
C2K-1800HSV
Wiring Diagram 230V 2/01
WARNING: All electrical repairs must be performed by qualified personnel only.
Page -24 -
CLARKE TECHNOLOGY Operator's Manual - C2K Series
ALTO® PRODUCT SUPPORT BRANCHES
U. S. A. Locations
HEAD OFFICE
European Locations
PRODUCTION FACILITIES
ALTO U.S. Inc., St. Louis, Missouri
16253 Swingley Ridge Road, Suite 200
Chesterfield, Missouri 63017-1725
PRODUCTION FACILITIES
ALTO U.S. Inc., Springdale, Arkansas
2100 Highway 265
Springdale, Arkansas 72764
(501) 750-1000
Customer Service - 1-800-253-0367
Technical Service - 1-800-356-7274
ALTO U.S. Inc., Bowling Green, Ohio 43402
1100 Haskins
SERVICE FACILITIES
ALTO U.S. Inc., Carlstadt, New Jersey 07072
150 Commerce Road
(201) 460-4774
ALTO U.S. Inc., Elk Grove, Illinois 60007
2280 Elmhurst Road
(847) 956-7900
ALTO U.S. Inc., Denver, Colorado 80204
1955 West 13th Ave.
(303) 623-4367
ALTO U.S. Inc., Houston, Texas 77040
7215 North Gessner Road
SALES AND SERVICE FACILITIES
ALTO U.S. Inc., Madison Heights, Michigan 48071-0158
29815 John R.
(810) 544-6300
ALTO U.S. Inc., Marietta, Georgia 30062
1355 West Oak Common Lane
(770) 973-5225
CLARKE TECHNOLOGY
AMERICAN SANDERS TECHNOLOGY
A.L. COOK TECHNOLOGY
Customer Service Headquarters and Factory
2100 Highway 265
Springdale, Arkansas 72764
(501) 750-1000
Technical Service
1-800-356-7274
ALTO Danmark A/S, Aalborg
Blytaekkervej 2
DK-9000 Aalborg
+45 72 18 21 00
ALTO Danmark A/S, Hadsund
Industrikvarteret
DK-9560 Hadsund
+45 72 18 21 00
SALES SUBSIDIARIES
ALTO Canada Ltd., Rexdale Ontario
24 Constellation Ct.
(416) 675-5830
ALTO Overseas Inc., Sydney (Australia)
1B/8 Resolution Drive
Caringbah NSW 2229
+61 2 9524 6122
ALTO Cleaning Systems Asia Pte Ltd., Singapore
No. 17 Link Road
Singapore 619034
+65 268 1006
ALTO Deutschland GmbH, Bellenberg (Germany)
Guido-Oberdorfer-Straße 2-8
89287 Bellenberg
+49 0180 5 37 37 37
ALTO Cleaning Systems (UK) Ltd., Penrith
Gilwilly Industrial Estate
Penrith
Cumbria CA11 9BN
+44 1768 868 995
ALTO France S.A. Strasbourg
B.P. 44, 4 Place d’Ostwald
F-67036 Strasbourg
Cedex 2
+33 3 8828 8400
ALTO Nederland B.V. Vianen
Stuartweg 4C
NL-4131 NJ Vianen
+31 347 324000
ALTO Sverige AB, Molndal (Sweden)
Aminogatan 18
Box 4029
S-431 04 Molndal
+46 31 706 73 00
ALTO Norge A/S, Oslo (Norway)
Bjornerudveien 24
N-1266
+47 2275 1770
CLARKE TECHNOLOGY U.S. LIMITED WARRANTY
This ALTO Industrial/Commercial Product is warranted to be free from defects in materials and
workmanship under normal use and service for a period of five years from the date of purchase, when
operated and maintained in accordance with Clarke Technology's Maintenance and Operations Instructions.
This warranty is extended only to the original purchaser for use of the product. It does not cover
normal wear parts such as electrical cable, rubber parts and motor brushes.
Clarke Technology's liability under this warranty is limited to repair of the product and/or replacement of parts and is given to purchaser in lieu of all other remedies, including INCIDENTAL AND
CONSEQUENTIAL DAMAGES.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN. THERE
ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. NO
WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY, SHALL BE
IMPLIED. A warranty registration card is provided with your Clarke Technology floor machine. Return
the card to assist Clarke Technology in providing the performance you expect from your new floor
machine.
If a difficulty develops with the product, you should: (a) Contact the nearest authorized Clarke
Technology repair location or contact the Clarke Technology Service Operations Department, 2100
Highway 265, Springdale, AR 72764, for the nearest authorized Clarke Technology repair location.
Only these locations are authorized to make repairs to the product under this warranty. (b) Return the
product to the nearest Clarke Technology repair location. Transportation charges to and from the
repair location must be prepaid by the purchaser. Clarke Technology will repair the product and/or
replace any defective parts without charge within a reasonable time after receipt of the product.
ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
ALTO reserves the right to make changes or improvements to
its machine without notice.
Always use genuine Clarke Technology Parts for repair.
CLARKE TECHNOLOGY
2100 Highway 265
Springdale, Arkansas, 72764