Samsung SDZ-300 Instruction manual

High Sensitivity, Day & Night
30X Zoom Color Camera
SALES NETWORK
•
•
SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do 462-703, Korea
TEL : +82-31-740-8137~8141 FAX : +82-31-740-8145
•
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.
7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China
TEL : +86-22-2761-4724(33821) FAX : +86-22-2761-6514
SDZ-300
SAMSUNG OPTO-ELECTRONICS UK, LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey KT16 OPS
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
INSTRUCTION MANUAL
P/No. : Z6806-0709-01A
VAN 06. 05
About this manual
Please read this manual carefully before installing and using the camera. Be sure to keep the manual handy for later reference.
Thank you for purchasing a SAMSUNG CCD CAMERA.
Before operating the camera, confirm the camera model and proper input
power voltage. In order to that you can understand this manual thoroughly,
we'll introduce our model description.
■ SDZ-300 SERIES
•NTSC MODEL
SDZ-300ND
SDZ-300N
•PAL MODEL
SDZ-300PD
SDZ-300P
■ MODEL DESCRIPTION
• SDZ-300X
_ _X
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
POWER SOURCE
SIGNAL SYSTEM
• SIGNAL SYSTEM
N NTSC MODEL
PAL MODEL
P
• POWER SOURCE
D DC 12V
-- DC 12V/AC 24V~ DUAL TYPE
INFORMATION -This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other
household wastes at the end of its working life. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
could void the user’s authority to operate the equipment.
WARNING - To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Features
Warning
The camera requires regular maintenance.
30x Optical Zoom
Day & Night
Contact an authorized technician for maintenance and/or servicing.
The built-in SDZ-300 optical zoom lens is a
highly durable component. It features auto
focus, auto iris, and zoom functions.
The camera automatically determines whether
it is night time or day time, selecting operating
mode automatically. The camera operates in
color mode during day light conditions and BW
mode in night conditions for clearer identification.
Do not continue to use if malfunctioning.
SSNR (Samsung Super Noise
Reduction)
By using built-in SSNR function manufactured
by SAMSUNG TECHWIN, the amount of low
illuminance noise has been significantly
reduced, and the signal-to-noise ratio (S/N)
as well as horizontal resolution have been
improved, resulting in a clear and sharp
image display even in the dark.
Fine Picture Quality under Ultra Low
Lighting
1/4" high density CCD allows the user to
capture bright, high-quality images under
ultra low lighting conditions.
DIS(Digital Image Stabilizer)
The DIS function can compensate for vibration of
the camera. so it helps you obtain more
stabilized image under the shaking conditions.
Do not Install the camera on a surface that can not support it.
Installation on an unsuitable surface may cause the camera to fall and/or other hazards.
Motion Detection
Once motion is detected, the camera sends
an alert signal to the processing unit, which, if
used in conjunction with an optional alarm,
can provide effective surveillance of your
property.
Miscellaneous Functions
Other miscellaneous functions of the camera
include privacy zone masking, digital zoom,
line lock synchronization (INT/LL), freeze,
horizontal inversion, and user-configured
presets.
High Resolution
Control via OSD Menu and RS-485
Featuring 520TV line horizontal resolution in
color mode and 570TV line horizontal resolution
in BW mode, the camera features Sony's
410,000 pixel CCD and captures clean,
noiseless, high-quality images.
Prolonged use of the camera in abnormal operating conditions (produces
smoke, overheats, etc.) may result in a fire.
The OSD menu and RS-485 pins allow for
remote control of the camera.
The user can also directly control the lens
using external control connection.
Do not handle the power cable with wet hands.
May result in an electric shock.
Do not disassemble the camera.
May result in a fire, electric shock, and/or other hazards.
Do not place the camera in the vicinity of inflammables.
May result in a fire and/or other hazards.
Contents
Precautions
8
• CAM TITLE
18
18
19
20
• WHITE BALANCE
23
• BACKLIGHT
24
25
26
Operating Your Camera
Menu Configuration
Menu Setup
Components and Accessories
Overview
Top
Bottom
Back
10
11
11
12
13
• MOTION DETECTION
• FOCUS
• EXPOSURE
• SPECIAL
• RESET
• EXIT
Connection
Connecting To Monitor
Connecting To Power
Connecting To Connection
14
14
15
16
30
35
41
41
Troubleshooting
42
Specification
44
STW Protocol Command Description
46
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Use only under temperature conditions
between -10˚C and +50˚C. Provide good
ventilation when using in high temperature
conditions.
Do not install under unstable
lighting conditions.
May lower image quality.
Do not drop the camera or
subject it to physical shock.
May cause a product malfunction.
Never keep the camera face to
strong light directly.
May damage the CCD.
Do not expose the camera to
rain or other types of liquids.
Do not expose the camera to
radioactivity.
Avoid touching the camera lens.
Wipe dry any liquids. Liquids may contain
minerals that are corrosive to electronic
components.
Radioactivity exposure may damage the
CCD.
Notes
Severe lighting changes or flickering may
hinder normal camera operation.
COLOR CCD CAMERA
8
The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.
User’s Manual
• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.
• Ensure that the power source complies with normal specifications before supplying
it to the camera.
COLOR CCD CAMERA
9
User’s Manual
Components and Accessories
Overview
Top
1. 30x Zoom Color Camera
SDZ-300
2. Instruction Manual
Tripod Mounting Bracket Screw Hole
Used to fix tripod mounting bracket on top of the camera.
3. 6-Pin Connection Cable
4. Remote Controller (Optional)
COLOR CCD CAMERA
10 User’s Manual
COLOR CCD CAMERA
11 User’s Manual
Overview
Bottom
Back
Tripod Mounting Hole
Used to install the camera on an optional tripod.
The tripod must be equipped with screws with
specifications shown on the right.
L
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
Key Buttons
· Following buttons control zoom, focus, and auto focus functions.
WIDE button : To widen the view. (ZOOM OUT)
TELE button : To close in on a far object. (ZOOM IN)
F-NEAR button : To see a near object clearly.
F-FAR button : To see a far object clearly.
AF button
: To activate auto focus just once.
Pressing the 'SET' button locks the zoom control function of these buttons and
prompts the main setup menu.
Notes
• The zoom postion is saved after 5 seconds when you set zoom function.
Attach the bracket to the top of the camera. Use screws
included in the package or their equivalent (less than
6mm). Otherwise, the bracket may not assemble to the
camera properly.
COLOR CCD CAMERA
12 User’s Manual
· Main setup menu can be navigated using these buttons.
SET : To access the main setup menu.
UP (WIDE button)
: To move the arrow indicator to up.
DOWN (TELE button) : To move the arrow indicator to down.
LEFT (F-NEAR button) : To move the arrow indicator to left.
RIGHT (F-FAR button) : To move the arrow indicator to right.
COLOR CCD CAMERA
13 User’s Manual
Overview
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate
device.
Power Input Terminal
Power supply terminal (DC12V±10%).
CCD Camera
Power LED
Illuminates when power is supplied.
Intermediate
End monitor
Video Output Jack
Used to connect an external video monitor in jack.
Communication Control Connector
Used to connect the Remote Controller (Optional). Includes external 'SYNC' signal
input pin, which is used for the line lock function.
Includes the RS-485 communication pin.
External Control Connector
Relates to the motion detection output signal.
Zoom and focus functions can be controlled using external siganals.
Connecting to Power
Connection
Each model has a different power input specification.
Please check the model type and standard power requirement before
connecting to power.
Connecting to Monitor
Use DC 12V/500mA power source for SDZ-300ND/PD.
DC Power Type (DC 12V, 500mA)
Connect Video Out Jack to the monitor's Video In jack as shown below.
CCD Camera
Monitor
Power Input Terminal
AC/DC Power Type
Use AC24V/500mA or DC 12V/500mA power
source for SDZ-300N/P.
Notes
• Connection methods may vary depending on the video equipment. Please
refer to the model specific instruction manual.
• Connect cables with the unit powered down.
COLOR CCD CAMERA
14 User’s Manual
• Connect the power once the installation is complete.
• The wire is polarized. Match '+' and '-' terminals properly.
COLOR CCD CAMERA
15 User’s Manual
Connection
Connecting to connection
External Control Connector
GND
MD
COM
FOCUS
ZOOM
Function
Connector
Signal Level
Tele
ZOOM
I/O
SCC-3000
+6V~+12V
COM
* Communication Control Connector Pin Description .
+6V~+12V
Far
FOCUS
COM
I
COM
-6V~-12V
Near
COM
COM
SCC-100
I
COM
-6V~-12V
Wide
Number
Name
Description
Number
Name
Description
1
GND
-
4
TRX +
RS-485 Communication
5
TRX -
RS-485 Communication
6
Output Power
Remote Controller only
2
3
-
EXT.SYNC External ‘SYNC’ Signal
GND
-
3V or 5V
* EXT. SYNC
0V
Min: 500ns
MD
0V
There is no motion
5±0.5sec
+4.0V~+5.0V
There is motion
6-Pin Connection
Cable
Remote Controller
O
* MD (Motion Detection) Output Signal Level (less than 10mA)
* When using the MD function, the 'GND' should be connected to the frame ground.
Communication Control Connector
The camera can be controlled by using external controllers like a Remote
controller. (RS-485 Communication)
60Hz ± 0.1Hz(NTSC), 50Hz ± 0.1Hz(PAL)
* Communication Setting can set the communication setting as shown in the table below.
When you use to connect SCC-100 or SCC-3000, the default sets for SCC-3000
ITEM
MODE
Data Bit
Bit/Sec
Parity
CAM ID NO.
RETURN PACKET
SCC-100
Serial
8 bit
9600bps
EVEN
0
ENABLE
Notes
• Contact an authorized technician for inspection.
COLOR CCD CAMERA
16 User’s Manual
COLOR CCD CAMERA
17 User’s Manual
SCC-3000
Serial
8 bit
9600bps
NONE
1~255
See the SCC-3000 manual
Operating Your Camera
Menu Configuration
Menu Setup
Use the six buttons on back of the camera.
MAIN SETUP MENU
CAM TITLE
•
OFF
•
ON
WHITE BALANCE
•
ATW(OUTDOOR)
•
AWC
BACKLIGHT
•
OFF
•
LOW
SET
•
MANUAL
•
MIDDLE
•
HIGH
MOTION DET
•
OFF
•
ON
FOCUS
•
MODE
•
ZOOM TRK
•
ZOOM SPEED
•
D-ZOOM
•
DISP ZOOM MAG
•
ZOOM POS INIT
•
LENS INIT
•
END
•
BRIGHTNESS
•
IRIS
•
SHUTTER
•
AGC
•
SSNR
•
SENS-UP
•
END
•
USER PRESET
•
PRIVACY
•
DAY/NIGHT
•
DIS
•
SYNC
•
COMM ADJ
•
IMAGE ADJ
•
END
EXPOSURE
SPECIAL
RESET
UP button
SET button
LEFT button
AF button
DOWN button
RIGHT button
1. Press the SET button to access the main setup mode.
• Main setup menu is displayed on the monitor screen.
MAIN SETUP
CAM TITLE
OFF
WHIET BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
EXIT
2. Select the desired feature using the UP or DOWN button.
• Each pressing of the UP or DOWN button moves the indicator to the next
or previous feature.
• Move the arrow indicator to the desired feature item.
COLOR CCD CAMERA
18 User’s Manual
COLOR CCD CAMERA
19 User’s Manual
Operating Your Camera
Select feature using the UP
or DOWN button.
3. Press SET button.
MAIN SETUP
CAM TITLE
OFF
WHIET BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
Change the status using the
LEFT or RIGHT button.
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.
Notes
• Features marked with a have an accessible submenu.
• Access the submenu by pressing the SET button.
4. You can enter up to 20 characters.
Move the cursor to the character entry field using the LEFT or RIGHT
button.
Use UP, DOWN, LEFT, and RIGHT buttons to select a desired character.
Cam Title
Use this feature to designate a name for the camera, which will display on the
monitor screen.
1. Press the SET button to display the main setup menu and move the arrow
indicator to 'CAM TITLE' using the UP or DOWN button.
2. Set 'CAM TITLE' to 'ON' using the LEFT or RIGHT button.
Notes
• If the CAM TITLE feature is set to 'OFF',
the name will not displayed in the monitor.
COLOR CCD CAMERA
20 User’s Manual
MAIN SETUP
CAM TITLE
OFF
WHIET BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
SPECIAL
RESET
EXIT
Press the SET button to confirm selection of the blinking character. The
character is then saved, and the cursor in the entry field moves to the
next position.
Repeat steps through until the desired name has been entered.
Notes
• Correcting Mistakes
Move the cursor to 'CLR' and press the SET button to clear the entire entry.
To modify one character, use or to position the cursor above the character
to be modified and click the SET button after selecting the character to enter.
COLOR CCD CAMERA
21 User’s Manual
Operating Your Camera
5. Select on screen position of the CAM TITLE.
Move the cursor to 'POS' and press SET button.
White Balance Control
Your camera provides three 'WHITE BAL' control modes for your choosing in
adjusting the white balance.
1. Press the SET button to access the main setup menu and move the indicator
to 'WHITE BAL' using the UP or DOWN button.
2. Set 'WHITE BAL' using the LEFT or RIGHT button.
The CAM TITLE is displayed on the top-left of the monitor screen.
(Default position)
FRONT DOOR
MAIN SETUP
CAM TITLE
OFF
WHIET BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
The three white balance control modes are as follows :
to Locate, then SET
Select the position by using the 4-directional buttons, then press the SET
button to confirm the position.
FRONT DOOR
to Locate, then SET
6. When completed, move the cursor to 'END' and press SET button.
COLOR CCD CAMERA
22 User’s Manual
ATW(Auto Tracking White Balance):
• OUTDOOR: This mode can be used within the color temperature range 1800~10500˚K
(Ex: fluorescent light, outdoor, sodium vapor lamp or inside tunnels)
• INDOOR : This mode can be used within the color temperature range 3000K~10500˚K.
AWC(Auto White balance Control):
The white balance is automatically adjusted in a specific environment. In order to
obtain the best result, press the SET button while the camera focuses on white
paper. If the environment including the light source is changed, you have to adjust
the white balance again.
Manual:
To fine adjust, select the Manual mode. You can increase or decrease the red or
blue factor while monitoring the difference on the screen. Set to 'MANUAL' mode
and press the SET button. Increase or decrease the value for red(R-Gain) and
blue(B-Gain), watching the color of the picture, and press the SET button when you
obtain the best color.
COLOR CCD CAMERA
23 User’s Manual
Operating Your Camera
Notes
Motion Detection
• Proper White Balance may not be obtained under the following conditions.
When the scene contains mostly high color temperature object, such as a blue
sky or sunset.
When the scene is dim.
If your camera directly faces a fluorescent lamp or is used in an environment of
varying lighting conditions.
Backlight
When there is a strong backlight behind the object, clear images of the background
as well as the object can still be obtained by using the BACKLIGHT function.
1. Please position the arrow to point to 'BACKLIGHT' on the SETUP menu by
using the UP and DOWN buttons.
2. Please select the mode you wish to operate by pressing the LEFT or RIGHT
button.
MAIN SETUP
CAM TITLE
OFF
WHIET BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
HIGH/MIDDLE/LOW: You can adjust the sensitivity of Backlight Compensation.
OFF: BACKLIGHT function does not operate.
Backlight ON
COLOR CCD CAMERA
This product has a feature that allows you to observe movements of objects in
4 different areas on the screen, and the words ‘MOTION DETECTED’ appear on
the screen when movement is detected; hence a single individual can conduct
supervision efficiently. The camera detects an object’s movement by sensing
disparity of outline, and level of brightness and color. The camera receives
detection signal from MD output terminal.
•Please press the SETUP button.
-OFF: MOTION DETECTION mode is cancelled.
-ON: Any motion in the selected areas is observed.
•Please press the SETUP button.
-OFF: MOTION DETECTION mode is cancelled.
-ON: Any motion in the selected areas is observed.
•Please select the area you wish to observe from the 4 areas in AREA SEL mode.
•Please select ON mode for the chosen area.
•Please adjust the size of the area to be observed by using the UP, DOWN, LEFT
or RIGHT button.
•Please press the SETUP button to save changes and complete the setting.
Notes
Tips on Using the Motion Detection Feature
• The feature may not function properly under flickering light conditions.
• The camera interprets sudden changes in lighting and subsequent change in
brightness of an object as motion.
• With the feature enabled, other algorithms may require
additional time to operate than usual.
• This system does not guarantee prevention of fire or
theft. The manufacturer shall not be held responsible for
any accident or damage incurred.
• Connect an external alarm device to MD Out on back of
the camera.
Backlight OFF
24 User’s Manual
COLOR CCD CAMERA
25 User’s Manual
Operating Your Camera
FOCUS
MAIN SETUP
CAM TITLE
OFF
WHIET BAL
ATW
BACKLIGHT
OFF
MOTION DET
OFF
FOCUS
EXPOSURE
SPECIAL
1. Press the SET button to access the main setup manu and then position the
indicator over FOCUS using the UP or DOWN button.
2. Press the SET button.
MODE: You can select the most suitable zoom mode. Move the arrow indicator to
‘MODE’ using UP or DOWN button.
FOCUS SETUP
MODE
ZOOM TRK
ZOOM SPEED
D-ZOOM
DISP ZOOM MAG
ONE-PUSH
ON
FAST
OFF
ON
•AUTO : Select AUTO and press the SET button to confirm. Increase or decrease
optical zoom (ZOOM) or digital zoom (DZOOM) positions using the UP or DOWN
button while verifying the changes on
screen. Enabling D-ZOOM (ON) means that
digital zoom will activate once optical zoom
ends. Focus is automatically adjusted with
moving zoom.
COLOR CCD CAMERA
26 User’s Manual
•ONE PUSH : Focus is automatically adjusted just once,
after zoom position is changed. Select '
ONE PUSH' and press the SET button to
confirm. Increase or decrease optical
zoom (ZOOM) or digital zoom (D-ZOOM)
positions using the directional buttons
while verifying the changes on screen. Press the SET button once
desired image quality is obtained.
•MANUAL : Select 'MANUAL' and press the SET button
to confirm. Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM) positions
using the directional buttons while verifying
the changes on screen. Press the SET button
once desired image quality is obtained. Focus
can be manually adjusted, independent of moving zoom.
ZOOM TRK: You can select to use ‘ZOOM TRK’. Move the arrow indicator to ‘ZOOM
TRK’ using UP or DOWN button. Set ‘ZOOM TRK’ to on using LEFT or
RIGHT button.
FOCUS SETUP
MODE
ZOOM TRK
ZOOM SPEED
ONE-PUSH
ON
FAST
ZOOM SPEED: Configure zoom tracing speed using this feature. Position the indicator
over 'ZOOM SPEED' using the UP or DOWN button and then set to
desired mode using the LEFT or RIGHT button.
FOCUS SETUP
MODE
ZOOM TRK
ZOOM SPEED
D-ZOOM
COLOR CCD CAMERA
ONE-PUSH
ON
FAST
OFF
27 User’s Manual
Operating Your Camera
•FAST: To move zoom fast.
•SLOW: To move zoom slowly.
Notes
• The 'ZOOM SPEED' mode cannot be used if 'MODE' is set to 'AUTO' and 'ZOOM
TRK' is 'ON'.
D-ZOOM: Configure magnification limit from x2~x10 using this feature. Position the
indicator over 'D-ZOOM' using the UP or DOWN button. Set 'D-ZOOM' to
'ON' and press the SET button to confirm.
FOCUS SETUP
MODE
ZOOM TRK
ZOOM SPEED
D-ZOOM
DISP ZOOM MAG
ONE-PUSH
ON
FAST
ON
ON
· Set 'ZOOM LIMIT' to the desired level using the LEFT or
RIGHT button.
DISP ZOOM MAG: Use this feature to display the current zoom magnification level on
screen. Position the indicator over 'DISP ZOOM MAG' using the UP
or DOWN button. Then set to ON using the LEFT or RIGHT button.
ZOOM POS INIT: Moves to the controlled ZOOM position when the power truned
on and is a function of the initial ZOOM position control.
FOCUS SETUP
MODE
ZOOM TRK
ZOOM SPEED
D-ZOOM
DISP ZOOM MAG
ZOOM POS INIT
LENS INIT
ONE-PUSH
ON
FAST
ON
ON
ON
ON
LENS INIT : Use this feature to initialize the lens. Position the indicator over LENS
INIT. using the UP or DOWN button. Press the SET button to confirm.
FOCUS SETUP
MODE
ZOOM TRK
ZOOM SPEED
D-ZOOM
DISP ZOOM MAG
ZOOM POS INIT
LENS INIT
END
ONE-PUSH
ON
FAST
OFF
ON
OFF
ON
FOCUS SETUP
MODE
ZOOM TRK
ZOOM SPEED
D-ZOOM
DISP ZOOM MAG
COLOR CCD CAMERA
ONE-PUSH
ON
FAST
OFF
ON
28 User’s Manual
END: To revert to the main setup menu.
COLOR CCD CAMERA
29 User’s Manual
Operating Your Camera
EXPOSURE
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
SENS-UP
END
50.......
AUTO
--MIDDLE
MIDDLE
AUTO
IRIS: Set 'IRIS' to 'AUTO' or 'MANUAL'. Position the indicator over 'IRIS' using the UP
or DOWN button and then select the desired iris mode using the LEFT or RIGHT
button.
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
50.......
AUTO
--MIDDLE
•AUTO: The iris is automatically activated upon illumination.
•MANUAL: Manual iris configuration. Set 'IRIS' to 'MANUAL' using the LEFT or
RIGHT button and then press the SET button. Increase or decrease iris
level using the LEFT or RIGHT button while verifying the changes on screen.
1. Press the SET button to access the main setup menu and then position the
indicator over 'EXPOSURE' using the UP or DOWN button.
2. Press the SET button to confirm.
BRIGHTNESS: Use this feature to adjust image brightness. Position the
indicator over 'BRIGHTNESS' using the UP or DOWN button.
Then increase or decrease brightness level using the LEFT or
RIGHT button while verifying the changes on screen. Set END
once desired level is obtained.
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
SENS-UP
END
COLOR CCD CAMERA
50.......
AUTO
--MIDDLE
MIDDLE
AUTO
30 User’s Manual
SHUTTER : Control image brightness by adjusting shutter speed.
1. Position the indicator over 'SHUTTER' using the UP or DOWN button. Then select
the desired shutter mode (A.FLK, ESC, MANUAL) using the LEFT or RIGHT button.
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
COLOR CCD CAMERA
50.......
AUTO
--MIDDLE
MIDDLE
31 User’s Manual
Operating Your Camera
•A.FLK (NTSC: 1/100, PAL: 1/120): Flicker-free mode
•ESC: Automatic shutter speed setting (optimal)
•MANUAL: Manual shutter speed setting
2. If you choose ‘MANUAL’, select the optimal shutter speed.
· In MANUAL mode, the optimal shutter speed needs to be designated. Select from 1/60
to 1/120,000 (NTSC) or from 1/50 to 1/120,000 (PAL).
* 'Sens-Up' mode can be configured manually (2x to 128x).
· Verify changes made to the shutter speed by referencing to changes in on screen
brightness.
AGC (Auto Gain Control): For brighter images.
1. Position the indicator over 'AGC' using the UP or DOWN button.
2. Set 'AGC' to the desired mode using the LEFT or RIGHT button.
•HIGH
: Wide range gain value adjustment
•MIDDLE : Middle range gain value adjustment
•LOW
: Narrow range gain value adjustment
•OFF
: Disabled
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
50.......
AUTO
--MIDDLE
MIDDLE
SSNR(Samsung Super Noise Reduction): On screen noise reduction.
3. Press the SET button to complete.
Notes
• Image may become unstable if the camera is set to 'ESC' mode and faces a strong
fluorescent light.
• Under 'ESC' mode, the brightness can be adjusted using the LEFT or RIGHT button.
• The WDR feature is not available under MANUAL mode.
• Sens-up is disabled under 'MANUAL' or 'A.FLK' mode.
COLOR CCD CAMERA
32 User’s Manual
1. Position the indicator over 'SSNR' using the UP or DOWN button.
2. Set 'SSNR' to the desired mode using the LEFT or RIGHT button.
•LOW : Low noise reduction
•MIDDLE : Medium noise reduction
•HIGH : High noise reduction
•OFF
: Disabled
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
SENS-UP
COLOR CCD CAMERA
50.......
AUTO
--MIDDLE
MIDDLE
AUTO
33 User’s Manual
Operating Your Camera
SPECIAL
Notes
• Changing 'AGC' setting from LOW to HIGH results in greater sensitivity, as well as
on screen noise.
• Setting 'AGC' to OFF locks 'SSNR' configuration.
SENS-UP : This feature ensures clear images at night or under low lighting
conditions.
1. Position the indicator over 'SENS-UP' using the UP or DOWN button.
2. Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button.
•AUTO : Select this mode for use in night time or under low lighting conditions.
•OFF : Disabled
EXPOSURE SETUP
BRIGHTNESS
IRIS
SHUTTER
AGC
SSNR
SENS-UP
END
50.......
AUTO
--MIDDLE
MIDDLE
AUTO
Notes
• Once 'AUTO' mode is set, the user can configure Sens-Up limit by increasing
/decreasing the shutter speed (e.g.: x2,...,x32, x64,..., x128).
• Enabling Sens-Up increases camera sensitivity and may result in additional noise
and/or other phenomenons. This is normal.
COLOR CCD CAMERA
34 User’s Manual
SPECIAL SETUP
USER PRESET
OFF
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
END
1. Press the SET button to access the main setup menu and then position the
indicator over 'SPECIAL' using the UP or DOWN button.
2. Press the SET button to confirm.
USER PRESET:
Preset user-designated configurations using this feature. Position the indicator
over 'USER PRESET' using the UP or DOWN button and then set to 'ON' using the
LEFT or RIGHT button. Press the SET button to confirm.
SPECIAL SETUP
USER PRESET
OFF
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
END
COLOR CCD CAMERA
35 User’s Manual
Operating Your Camera
•PRESET NO : Up to eight different preset configurations are supported.
USER PRESET SETUP
PRESET NO.
NO. 1
PRESET MODE
ON
PRESET SAVE
PRESET CLEAR
END
PRESET DEFINED
•PRESET MODE: Configure initial settings under FOCUS, EXPOSURE, etc.
•PRESET CLEAR: Clear configured preset.
USER PRESET SETUP
PRESET NO.
NO. 1
PRESET MODE
ON
PRESET SAVE
PRESET CLEAR
END
PRESET DEFINED
•END: Revert to the SPECIAL SETUP menu.
USER PRESET SETUP
PRESET NO.
NO. 1
PRESET MODE
ON
PRESET SAVE
PRESET CLEAR
END
PRESET DEFINED
•PRESET SAVE: Save configured preset.
USER PRESET SETUP
PRESET NO.
NO. 1
PRESET MODE
ON
PRESET SAVE
PRESET CLEAR
END
PRESET DEFINED
COLOR CCD CAMERA
36 User’s Manual
PRIVACY: Mask privacy area using this feature. The mask area expand/contract
upon the zoom position.
SPECIAL SETUP
USER PRESET
OFF
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
COLOR CCD CAMERA
37 User’s Manual
Operating Your Camera
•GROUP SEL : Choose up to eight groups. Each group can consist of four mask
areas.
•MASK COLOR : Adjust desired mask color level.
•AREA SEL
: Configure eight mask areas.
•AREA MODE : Mask area display.
•TOP
: To move the mask area up.
•BOTTOM
: To move the mask area down.
•LEFT
: To move the mask area left.
•RIGHT
: To move the mask area right.
DIS : The DIS mode can compensate for vibration of the camera.
SPECIAL SETUP
USER PRESET
OFF
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
Notes
• When DIS is operating, D-ZOOM does not operate.
SYNC : Two synchronization modes are available INTERNAL and EXTERNAL LINE-LOCK.
In LINE-LOCK mode, it synchronizes the camera’s video out signal to the external
SYNC signal.
DAY/NIGHT: Select from COLOR, BW or AUTO modes.
SPECIAL SETUP
USER PRESET
OFF
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
COMM ADJ
IMAGE ADJ
•COLOR : Color mode.
•B/W : BW mode.
•AUTO : The camera automatically detects lighting conditions and selects the mode
accordingly.
COLOR CCD CAMERA
38 User’s Manual
SPECIAL SETUP
USER PRESET
OFF
PRIVACY
OFF
DAY/NIGHT
COLOR
DIS
OFF
SYNC
INT
COMM ADJ
•INT : Internal synchronization
•LL : External line-lock synchronization
· If you choose ‘LL’, you can adjust the desired phase.
Press the SET button.
· You can adjust the desired phase from 0 to 359.
COLOR CCD CAMERA
39 User’s Manual
Operating Your Camera
Notes
• For NTSC models, the line-lock mode can be used if the external SYNC signal
frequency is at 60Hz.
• For PAL models, the line-lock mode can be used if the external SYNC signal
frequency is at 50Hz.
COMM ADJ: Use this feature to select communication
protocol (refer to p.46~ p.51 for details).
Position the indicator over
'COMMUNICATION' using the UP or
DOWN button.
•FREEZE: Use this feature to freeze capture an image.
•H-REV: Use this feature to horizontally inverse the screen.
•V-REV: Use this feature to vertically inverse the screen.
•SHARPNESS : Increasing this value sharpens object edges. Too high of a setting,
however, produces noise and may obscure the image.
•COLOR
: Adjusting this value affects the chroma level only; the burst level is
unaffected.
END: evert back to the USER PRESET menu.
RESET
To reset your camera to factory default condition.
•CAM ID : Assign an ID number to the camera (1 to 255).
Identification number zero is used for Remote controller setup.
•DISP CAM ID: Displays camera ID on top left corner of the screen.
•BAUD RATE : Configure baud rate from 2400/4800/9600/19200/38400/57600 bps.
•UART MODE : Configure parity bit to NON, EVEN, or ODD. Data bit is set to 8bit,
and stop bit to 1bit. Set the UART MODE to EVEN if using the Remote
Controller.
•RET PKT : Used to transfer a packet.
•END
EXIT
To finish setup menu.
IMAGE ADJ: Includes image quality or special function
factors.
COLOR CCD CAMERA
40 User’s Manual
COLOR CCD CAMERA
41 User’s Manual
Troubleshooting
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
Problem
Solution
No display
• Check the power cable and the wiring between the
camera and the monitor.
• Ensure proper video cable connection (Video Out
Jack).
Dim display
• The lens could be dirty. Clean with a soft, clean
piece of cloth.
• Adjust monitor settings.
• Adjust camera position if exposed to a strong light
source.
Dark display
• Adjust the monitor's contrast level.
• Set the intermediate device, if in use, to 75Ω/ Hi-z
(refer to p.15).
The camera is not
functioning properly and
its surface is hot
• Check the power source for compliance with
specifications.
Motion Detection
feature is not active.
• Ensure that the feature is set to ON.
COLOR CCD CAMERA
42 User’s Manual
Problem
Solution
Uneven colors
Flickering
• Adjust and configure WHITE BAL.
• The camera may be facing the sun or a fluorescent
light. Adjust the position of the camera.
Can't select LL mode
• The camera may be connected to a DC power
source. Connect to an AC power source.
LL is not function
properly.
• Check external SYNC signal frequency (should be
60Hz for NTSC, 50Hz for PAL).
COLOR CCD CAMERA
43 User’s Manual
Specifications
SDZ-300ND
Input Voltage
P
O
W
E
R
DC 10V~14V
(Recommended :
12V)
Input Current
C
C
D
O
P
T
I
C
S
S
y
n
c.
E
L
E
C
T
R
I
C
A
L
Size
Total Pixels
Effective Pixels
Optics
Min. Focus Distance
D. ZOOM
Angle Field of view
Scanning System
Synchronization
Frequency
Camera Title
Camera ID
Resolution
Video Output
S/N (Y signal)
Min. Illumination
Backlight Compensation
Day & Night
SDZ-300PD
SDZ-300P
DC 10V~14V
(Recommended :
12V)
DC 12V(±15%)
AC 24V(±15%)
250mA:
Steady-state
416mA:
Max (Zoom, Focus,
Day&night motor
operating)
Power Consumption 3W: Normal
5W: Max (Zoom,
Focus, Day &
Night motor
operating,
at 12V)
SDZ-300N
DC 12V(±15%)
AC 24V(±15%)
DC 12V
333mA:
Steady-state
500mA:
Max (Zoom, Focus,
Day&night motor
operating)
250mA:
Steady-state
416mA:
Max (Zoom, Focus,
Day&night motor
operating)
DC 12V
333mA:
Steady-state
500mA:
Max (Zoom, Focus,
Day&night motor
operating)
DC12V:
Normal 3W/Max
5W
AC 24V:
Normal 4W/Max
6W
3W: Normal
5W: Max (Zoom,
Focus, Day &
Night motor
operating,
at 12V)
DC12V:
Normal 3W/Max
5W
AC 24V:
Normal 4W/Max
6W
1/4 inch, Color Super HAD CCD
811(H) x 508(V)
795(H) x 596(V)
768(H) x 494(V)
752(H) x 582(V)
30X, f=3.3 to 99.0mm (F 1.6 to 3.2)
1000mm
OFF/ON (Limit 10x)
H : Appr. 58.0˚(Wide) to 2.22˚(Tele) V : Appr. 44.8˚(Wide) to 1.68˚(Tele)
2:1 Interlace
Internal / Line Lock
Horizontal:15.734 KHz/Vertical :59.94 Hz
Horizontal: 15.625 KHz/Vertical : 50.00 Hz
ON/OFF (Displayed 20 characters)
255 ID Selectable
520 TV Lines(Min.) : Color 570 TV Lines(Min.) : B/W
CVBS : 1.0Vp-p/75Ω
50 dB (AGC Off, Weight ON)
0.6 Lux @ F1.6: Color / 0.1 Lux @F1.6: B/W
LOW/MIDDLE/HIGH/OFF Selectable
AUTO/COLOR / B/W(ICR type)
COLOR CCD CAMERA
44 User’s Manual
SDZ-300ND
SDZ-300N
SDZ-300PD
SDZ-300P
Gain Control
Low, Middle, High,OFF Selectable
White Balance
ATW (INDOOR (3,000K~10,500K), OUTDOOR (1,800K~10,500K))/AWC/MANUAL
Electronic shutter speed AUTO/MANUAL (X128 ~ 1/60sec ~ 1/120,000sec) AUTO/MANUAL (X128 ~1/50sec ~ 1/120,000sec)
Sens-up Limit is selectable
E
L
E
C
T
R
I
C
A
L
O.S.D
Motion Detection
SSNR
Focus
Zoom Movement Speed
Lens Initialize
Preset
DIS
Privacy Function
FLIP
FREEZE
IRIS Control
Communication
Control Output
Operating
Temperature/Humidity
Dimension
Weight
Option
Sens-up Limit is selectable
Built-In
ON/OFF (Built-in alarm output connector)
LOW/MIDDLE/HIGH/OFF Selectable (Noise Control)
Auto / Manual / One Push
5.2 Sec : Wide to Tele
5.4 Sec : Wide to Tele
Built-In
8-Positions
ON / OFF
ON/OFF(32 Zones, 8 Group / 4 Programmable Zone per Screen)
LEFT/RIGHT, UP/DOWN
On/Off
Auto/Manual
RS-485(2,400bps, 4800bps, 9600bps, 19200bps, 38,400bps, 57,600bps Selectable)
STW PROTOCOL AVAILABLE (refer to p46 STW Protocol Command Description)
PELC0-D PROTOCOL AVAILABLE
External Control by Voltage (ZOOM, FOCUS)
-10˚C to +50˚C / 30% to 90% RH
64(W) X 64(H) X 140(D)mm
410g
Remote Controller(RS-485 type)
COLOR CCD CAMERA
45 User’s Manual
STW Protocol Command Description
Command Name
Reset
Focus Far
Focus Near
Zoom Wide
Zoom Tele
ZOOM Direct
AF Stop
One push AF
Command Packet
Return Packet
Checksum
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Parameter
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
COLOR CCD CAMERA
46 User’s Manual
Byte1
Byte2
Byte3
STX
CAM ID
HOST ADDR
STX
CAM ID
HOST ADDR
CHECKSUM CALCULATION: UNARY OPERATION
C SOURCE EX) CHECKSUM = ~(BYTE2+BYTE3+...
Reset all data to factory default value.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move focus lens to far direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move focus lens to near direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move zoom lens to wide direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move wide lens to tele direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move ZOOM lens to specific position directly
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
P1, P2: OPTICAL ZOOM = 0000h~06EAh
P3: DIGITAL ZOOM = ((256*10)/Ratio)-1
ex) D-ZOOM 1.1x : P3 = E7h = ((256*10)/11)-1,
D-ZOOM 2.0x : P3 = 7Fh = ((256*10)/20)-1,
Stop zoom & focus lens moving.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Unconditionally execute auto focus.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Byte4 ll Byte5
Byte 6
Byte7
CAMMAND
DATA3
DATA4
CAMMAND
DATA3
DATA4
OF SUMMATION FROM BYTE2 TO BYTE9.
+BYTE8+BYTE9);
Byte8
DATA5
DATA5
Byte9
DATA6
DATA6
Byte10
ETX
ETX
Byte11
CHECKSUM
CHECKSUM
000Fh
000Fh
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0100h
0100h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0200h
0200h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0040h
0040h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0020h
0020h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
00FFh
00FFh
P1
P1
P2
P2
P3
P3
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0000h
0000h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0045h
0045h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
Ratio 11 means 1.1x.
Ratio 20 means 2.0x.
COLOR CCD CAMERA
47 User’s Manual
STW Protocol Command Description
USER PRESET Save
Function
Save current user preset configuration information.
Command Packet
A0h
CAM ID
HOST ADDR
0003h
P1
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0003h
P1
00h
00h
00h
AFh
CHECK SUM
Parameter
P1: 00h = USER PRESET 1
01h = USER PRESET 2
02h = USER PRESET 3
03h = USER PRESET 4
04h = USER PRESET 5
05h = USER PRESET 6
06h = USER PRESET 7
07h = USER PRESET 8
USER PRESET EXEC.
Function
Execute selected user preset.
Command Packet
A0h
CAM ID
HOST ADDR
0007h
P1
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0007h
P1
00h
00h
00h
AFh
CHECK SUM
Parameter
P1: 00h = USER PRESET 1
01h = USER PRESET 2
02h = USER PRESET 3
03h = USER PRESET 4
04h = USER PRESET 5
05h = USER PRESET 6
06h = USER PRESET 7
07h = USER PRESET 8
OSD Menu On/Off
Function
Display OSD menu on the screen.
Clear OSD menu and save current menu setup.
Command Packet
A0h
CAM ID
HOST ADDR
00B1h
P1
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
00B1h
P1
00h
00h
00h
AFh
CHECK SUM
Parameter
P1: 00h = ON
01h = OFF
COLOR CCD CAMERA
48 User’s Manual
COLOR CCD CAMERA
49 User’s Manual
STW Protocol Command Description
OSD Menu Up
OSD Menu Down
OSD Menu Left
OSD Menu Right
OSD Menu Set
OSD Menu ESC
Function
Move OSD arrow to up.
Command Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to down.
Command Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to left.
Command Packet
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to right.
Command Packet
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Functio
Move to inside menu
Command Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move to upper menu.
Command Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
COLOR CCD CAMERA
50 User’s Manual
COLOR CCD CAMERA
51 User’s Manual
DECLARATION OF CONFORMITY
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
European Representative Name
European Representative Address
Equipment Type/Environment
CCTV Camera
Model Name
SDZ-300PD, SDZ-300P
Beginning Serial NO.
S6400001
Year of Manufacture
2006. 4. 1
Conformance to
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
SAMSUNG TECHWIN CO., LTD
Legal Representative in Europe
Full Name
YOUNG TAEK SON
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place
CHANGWON, KOREA
Place
Date
2006. 4. 1
Date
Manufacturer
Signature
Signature
MEMO
MEMO
MEMO