VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
shower
operation
& service guide
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Table of Contents
Current Products
Page
1C Showerheads (Figure 1) 215-1369-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bradtrol Valve (Figure 3) For Individual Showers 215-1369-1A . . . . . . . . . . . . . . . . . . . . . .6
Bradtrol Valve (Figure 4) For Econo-Wall, Wall Saver & Panelons 215-1369-1B . . . . . . . . .7
Bradtrol Valve (Figure 5) For Column Showers 215-1369-1C . . . . . . . . . . . . . . . . . . . . . . . .8
Bradtrol Valves – How they Work 215-1369-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Column Shower & Wall Shower Showerheads (Figure 6) 215-1369-17 . . . . . . . . . . . . . . . . .9
Column Shower Drains (Figure 7) 215-1369-22 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Column Shower Solenoid – Müeller (Figure 8) 215-1369-21 . . . . . . . . . . . . . . . . . . . . . . . .11
Column Shower Covers 215-1369-31 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-13
Compression Valve with Lever Handle – Hot, Cold or Tempered 215-1369-2A . . . . . . . . . .70-71
Compression Valve, Current Style – Hot, Cold or Tempered 215-1369-2B . . . . . . . . . . .72-73
1C Single Compression Valve with Lever Handle 215-1369-2C . . . . . . . . . . . . . . . . . . .74-75
1C Single Compression Valve 215-1369-2D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76-77
Compression Valves 1949 to Present (Figure 27) 215-1369-23 . . . . . . . . . . . . . . . . . . . . . . .89
Diverter Shower Valve (Figure 9) 215-1369-3A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Diverter Valve – In Wall (Figure 11) 215-1369-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Diverter Shower Valves – How they Work 215-1369-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Equa-Flo Valve, Version Prior to 2002 (Figure 10a) 215-1369-5 . . . . . . . . . . . . . . . . . . .16-17
Equa-Flo Valve, March, 2002 to July, 2004 (Figure 10a) 215-1369-5 . . . . . . . . . . . . . . .18-20
Equa-Flo Valve, Current Version (Aug, 2004 to Present) for Individual, Econo-Wall,
Wall Savers, and Panelons 215-1369-32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-22
Equa-Flo Valve, Current Version (Aug, 2004 to Present) for
Column Showers 215-1369-32A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23-24
Equa-Flo HD Pressure Balancing Valve for Individual, Econo-Wall,
Wall Saver and Panelon Showers 215-1369-29 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-26
Equa-Flo HD Pressure Balancing Valve for Column Showers 215-1369-29A . . . . . . . .27-28
Hand Held Shower (215-1369-30) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Infrared Sensor S83-099 (Figure 12) 215-1369-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Metering Air Valve (Figure 13) 215-1369-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44-46
Metering Air Valve For Column Showers (Figure 13a, 13b, 13c) 215-1369-8A . . . . . . .47-51
Micro-Touch™ III (Figure 14) 215-1369-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52-59
Pressure Balancing Mixing Valve S27-022 (Figure 15) 215-1369-7A . . . . . . . . . . . . . . .60-61
Pressure Balancing Mixing Valve S27-025 (Figure 16) 215-1369-7B . . . . . . . . . . . . . . .62-63
Presto Valves & Cartridges (Figure 17) 215-1369-15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Pushbutton Air Valve Repair Parts (Figure 18) 215-1369-11A . . . . . . . . . . . . . . . . . . . . . . .65
Pushbutton Air Valve Repair Parts (Figure 19) 215-1369-11B . . . . . . . . . . . . . . . . . . . . . . .66
Pushbutton Air Valve Repair Parts For Column Showers (Figure 32) 215-1369-11C . . . . .67
Showerheads WS-1X (Figure 20) 215-1369-19A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Showerheads 1WCA, Econowall, 1F, 1K and Panelon (Figure 21) 215-1369-19B . . . . . . .69
Solenoid Valves (Figure 24) 215-1369-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Stainless Steel, Enamel Surface and Drains 215-1369-26 . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Thermostatic Mixing Valve – (Model S59-2005) 215-1369-28 (April, 2003 to Present) 29-32
Thermostatic Mixing Valve For Column Showers 215-1369-28A . . . . . . . . . . . . . . . . . .33-36
2
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Bradley Showers
Current Products...continued
Page
Thermostatic Mixing Valve – (Model S59-2006) 215-1369-28B (2000 to April, 2003) .37-40
Touch 'N Flo Valve, Current Version (Figure 25) 215-1369-6 . . . . . . . . . . . . . . . . . . . . .79-82
TouchTime® (Figure 26) 215-1369-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83-84
TouchTime® With Battery Operation (Figure 33) 215-1369-27 . . . . . . . . . . . . . . . . . . . .85-86
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Discontinued Products
Bradley Thermostatic Mixing Valve (Figure 2) 215-1369-16 . . . . . . . . . . . . . . . . . . . . . . . .88
Metered Shower Valve S27-024 (Figure 28) 215-1369-25A . . . . . . . . . . . . . . . . . . . . . . . . .90
Metered Shower Valves S27-023 215-1369-25B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Pos-I-Pak Valve (Figure 30) 215-1369-24A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Pos-I-Pak Valves (Figure 31) 215-1369-24B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Cleaning of Shower Materials
Stainless Steel, Enamel Surface and Drains 215-1369-26 . . . . . . . . . . . . . . . . . . . . . . . . . . .94
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
3
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
1C Showerheads
(Figure 1)
Operation and Service Instructions
154-030
Showerhead Plate (If used)
154-126
Showerhead Arm
160-133
Screw
(4)160-151
Screws for Showerhead Plate
160-133
Screw
9/16"-18 UNF
Thread
3/8"-18 NPT
Thread
153-320
Adapter
153-321
Adapter
9/16"-18 UNF
Thread
1/2"-14 NPT
Thread
Deluxe Showerheads
Standard Institutional Showerheads
1/2"-14 NPT
3/8"-18 NPT
Standard Showerhead S24-008 *
Ball Joint S24-093
Showerhead w/ Arm and Plate S24-074
Lockable Ball Joint S24-095
Showerhead w/ Arm and Plate S24-175
Showerhead w/ Arm and Plate S24-044 *
3/8"-18 NPT
1/2"-14 NPT
S24-008
S02-058
Allen Key Volume Control S24-111 *
Showerhead w/ Arm and Plate S24-046 *
3/8"-18 NPT
S24-008
SX Showerhead
S24-161 *
Showerhead w/ Arm S24-088 *
Fixed direction
spray pattern
is adjustable
only through
orifice with 1/8"
Allen Key
Allen Key Volume Control Ball Joint S24-099
Showerhead w/ Arm and Plate S24-171
Allen Key Volume Control Lockable Ball Joint S24-101
Showerhead w/ Arm and Plate S24-176
S02-057
Lever Handle Volume Control S24-112 *
Showerhead w/ Arm and Plate S24-045 *
1/2"-14 NPT
3/8"-18 NPT
S24-008
S54-002
Lockable Ball Joint Assembly S24-108 *
Showerhead w/ Arm and Plate S24-127 *
Lever Handle Volume Control Ball Joint S24-096
Showerhead w/ Arm and Plate S24-074D
Lever Handle Volume Control Lockable Ball Joint S24-098
Showerhead w/ Arm and Plate S24-170
1/2"-14 NPT
3/8"-18 NPT
S24-008
S54-002
S02-058
Economy Soft Flow With Ball Joint 269-919
Showerhead w/ Arm and Plate S24-138
Lockable Ball Joint Assembly With Allen Key Volume Control S24-109 *
Showerhead w/ Arm and Plate S24-130 *
3/8"-18 NPT
* Add suffix G for 1.5 GPM Flow Restrictor
(Example: S24-044G)
S54-002
S24-008
S02-057
Lockable Ball Joint Assembly With Lever Handle Volume Control S24-110 *
Showerhead w/ Arm and Plate S24-133 *
4
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Bradtrol Valves
How they Work: Refer to Figure 3.
Counter-clockwise rotation of the handle and cam causes the rubber sleeve & insert to contract which
uncovers the ports in the cartridge allowing water to flow through the valve body.
Troubleshooting
PROBLEM
CAUSE
SOLUTION
Water drips from shower
head.
Mineral or foreign material
build up on cartridge ports
Clean or replace cartridge
and sleeve & insert
Water will not shut off.
Sleeve & insert split
Replace sleeve & insert
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
5
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Bradtrol Valve
Operation and Service Instructions
(Figure 3)
For Individual Showers
Figure 3
Parts List
Assembly
6
Valve Assembly
Part No.
300-0888
Repair Kit
Part No.
300-0760
Item
Part No.
Description
Qty
1
300-0876
Valve Body
1
2
300-0602
Gasket
1
1
1
3
300-0601
Cartridge
1
1
1
4
300-0935
Sleeve & Insert
1
1
1
5
300-1036
Cam
1
1
6
300-0306
Cam Bearing
1
1
7
300-0877
Cam Bearing Cover
1
1
8
300-0312
Screw
3
3
9
300-0379
Escutcheon
1
10
160-290
Screw
2
11
128-032
Handle
1
12
160-225
Screw
1
301-0140
Instructions
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Bradtrol Valve
(Figure 4)
For Econo-Wall, Wall Saver And Panelons
Figure 4
Parts List
Assembly
Valve Assembly
S21-025
Repair Kit
300-0760
Item
Part No.
Description
Qty
1
300-0875
Valve Body
1
2
300-0602
Gasket
1
1
1
3
300-0601
Cartridge
1
1
1
4
300-0935
Sleeve & Insert
1
1
1
5
120-020A
Cam
1
1
6
121-015
Cam Bearing
1
1
7
300-0312
Screw
3
3
8
128-032
Handle
1
9
160-225
Screw
1
301-0140
Instructions
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
7
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Bradtrol Valve
Operation and Service Instructions
(Figure 5)
For Column Showers
1
2
4
3
5
6
8
7
9
10
11
Parts List
Figure 5
Assembly
Item
Valve Assembly
Part No.
S21-023
Repair Kit
Part No.
300-0760
Part No.
Description
1
125-001BS
Gasket
1
2
169-269
Gasket
1
3
118-094
Adapter
1
1
4
300-0602
Gasket
1
1
1
5
300-0601
Cartridge
1
1
1
6
300-0935
Sleeve & Insert
1
1
1
7
120-020
Cam
1
1
8
121-015
Cam Bearing
1
1
9
300-0312
Screw
3
3
10
128-032
Handle
1
11
160-225
Screw
1
301-0140
Instructions
Escutcheon and screws (not shown) must be ordered separately.
as follows:
150-061
150-062
160-176
160-177
Escutcheon, 6-Person Shower
Escutcheon, 2-5 Person Shower
Screw for upper escutcheon note
Screw for lower escutcheon hole
Qty
1
Complete Replacement Valve:
S65-055
(2-5 Person)
S65-055A
(6 Person)
NOTE: If you want to reverse supplies, rotate cam 180° against
cartridge, reassemble handle.
8
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Column Shower & Wall Saver Showerheads
(Figure 6)
Showerhead Adapters For
Flared Connection
Supply Tube
Tube Connector 269-881
Nut 110-072A
Nut 110-072A
153-325
or
or
or
Plastic Head Core Assembly only
(complete with flow control):
S88-001, core w/2.5 GPM max
S88-003, core w/3.0 GPM max
S88-067, core w/1.5 GPM max
1/2"-14
NPT
3/8"-18
NPT
Standard Institutional Showerheads
For vandal prone
areas, substitute
S24-008 and 153-325
Plastic Showerhead in place of S24-072
Assembly S24-072 *
3/8"-18
NPT
Fixed direction
spray pattern
is adjustable
only through
orifice with 1/8"
Allen Key
Standard
Showerhead S24-008 *
3/8"-18 NPT
S24-008
or
1/2"-14
NPT
Showerhead Adapters
153-329, 153-383
for use with
Tube Connector 269-881
Used with Micro-Touch (MT),
Touch Time (TT) and
Air Metering (AST)
Deluxe Showerhead
1/2"-14 NPT
Ball Joint S24-093
Lockable Ball Joint S24-095
SX Showerhead
S02-058
Includes adaptor
and flow Control
S24-090 *
Allen Key Volume Control S24-111 *
3/8"-18 NPT
S24-008
153-383
SX Showerhead
3/8"-18 NPT
Vandal Resistant
153-329
153-319
(For use with
Flared Connection
Supply Tubes)
1/2"-14 NPT
Allen Key Volume Control Ball Joint S24-099
Allen Key Volume Control Lockable Ball Joint S24-101
S02-057
Lever Handle Volume Control S24-112 *
1/2"-14 NPT
3/8"-18 NPT
Lever Handle Volume Control Ball Joint S24-096
Lever Handle Volume Control Lockable Ball Joint S24-098
S54-002
S24-008
Lockable Ball Joint Assembly S24-108 *
3/8"-18 NPT
S24-008
S54-002
SX Showerhead
1/4"-18 NPT
Threaded Connector,
includes adaptor
and flow Control
S24-140 *
S02-058
Lockable Ball Joint Assembly With Allen Key Volume Control
S24-109 *
(For use with
Tube Connector
269-881)
1/2"-14 NPT
Economy Soft Flow With Ball Joint 269-919
3/8"-18 NPT
* Add suffix G for 1.5 GPM Flow Restrictor
(Example: S24-111G)
S24-008
S54-002
S02-057
Lockable Ball Joint Assembly With Lever Handle Volume Control
S24-110 *
Beach Shower
Foot Spray
S24-092
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
9
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Column Shower Drains
Operation and Service Instructions
(Figure 7)
Column Shower Drain Cover
(Less Drain Holes)
Part No. 107-287
10
Column Shower Drain Cover
(With Drain Holes)
Part No. 107-286
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Column Shower Solenoid — Müller
(Figure 8)
2
1
To Showerhead
3
4
1
Solenoid – Complete
2
Parts List
Solenoid
Assembly
S07-053
Item
1
2
3
3
4
Part No.
Description
125-001EB
269-882
R68-60000-11
R68-60000-11
S07-050
O-Ring
Connector
Plastic Tubing (2-5 Person)
Plastic Tubing (6 Person)
Solenoid
Plastic
Tubing
Qty
2
1
1
1
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
11
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
NOTE: CURRENT VERSION EFFECTIVE JANUARY, 2004
(CURRENT AND OLD ASSEMBLIES ARE INTERCHANGEABLE).
Column Shower Covers
SHROUD CLIP
159-413
#10-24 X 1/2"
SCREW
160-245
#10-24 X 3/4"
SCREW
160-142
RETAINERCOLUMN COVER
132-049
2-5 PERSON - NO SHROUD
S04-014A - CURRENT
S04-014A - PRIOR TO 2004
(THIS VERSION NO LONGER AVAILABLE)
PARTS SHOWN ABOVE FOR
CURRENT VERSION ONLY
2-5 PERSON - WITH SHROUD
S04-014A PLUS
(3) 159-413 SHROUD CLIPS
- CURRENT
2-5 PERSON WITH THERMOBLENDER
WITH SHROUD
S04-033 - CURRENT
S04-015A - PRIOR TO 2004
(THIS VERSION NO LONGER AVAILABLE)
S04-033 - PRIOR TO 2004
(THIS VERSION NO LONGER AVAILABLE)
NOTE: WHEN ORDERING A REPLACEMENT
COVER, CUSTOMER MUST ORDER THE
159-413 SHROUD CUP (3 REQUIRED)
IN ADDITION TO THE S04-014A
12
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Column Shower Covers
continued...
NOTE: CURRENT VERSION EFFECTIVE JANUARY, 2004
(CURRENT AND OLD ASSEMBLIES ARE INTERCHANGEABLE).
6 PERSON - NO SHROUD
S04-019A - CURRENT
S04-019A - PRIOR TO 2004
(THIS VERSION NO LONGER AVAILABLE)
6 PERSON - WITH SHROUD
S04-019A PLUS
(3) 159-413 SHROUD CLIPS
- CURRENT
S04-018A - PRIOR TO 2004
(THIS VERSION NO LONGER AVAILABLE)
6 PERSON WITH THERMOBLENDER
WITH SHROUD
S04-032 - CURRENT
S04-032 - PRIOR TO 2004
(THIS VERSION NO LONGER AVAILABLE)
NOTE: WHEN ORDERING A REPLACEMENT
COVER, CUSTOMER MUST ORDER THE
159-413 SHROUD CUP (3 REQUIRED)
IN ADDITION TO THE S04-019A
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
13
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Diverter Shower Valves
How they Work: Refer to Figure 9.
Clockwise rotation of the handle and stem causes the stem and washers (Item 3) to move in the casting
and divert the water flow to the shower head. Counter-clockwise rotation of the handle caused the
water flow to be diverted to the shower hose.
Troubleshooting
PROBLEM
14
CAUSE
SOLUTION
Water drips from handle or
bonnet.
O-Ring worn or bonnet
insufficiently tightened.
Replace O-Ring or tighten
bonnet.
Water will not divert.
Washers (Item 3) worked
loose from seat resulting in
washer not seating properly.
Replace washers
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Diverter Shower Valve
(Figure 9)
For Econo-Walls and Column Showers
Casting (part no. 118-124)
11
4
SHOWER
HOSE
1
IN
5
6
8
9
13
3
14
7
2
10
12
Figure 9
Parts List
Column Valve
Assembly Part No.
S45-323
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15*
124-001BU
124-001K
125-001CJ
118-126
150-035
150-004
120-028
142-002BF
124-001BD
125-001BC
121-012
128-050
153-163
160-225
S45-125
Washer
Washer
Washer
Valve Body
Escutcheon - Flat
Escutcheon - Column
Stem
Washer
Washer
O-Ring
Bonnet
Handle
Insert
Screw
Tube (Lubricant)
NOTE:
Wall Shower Valve
Assembly Part No.
S45-444
Qty
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
Does not include casting.
* Does not include recommended lubricant (Item 15). Order lubricant separately; apply lubricant to O-Rings.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
15
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo Shower Valve, Version Prior to March, 2002
(Figure 10)
For Individual, Econo-Walls, Wall Savers, Panelons and Column Showers
NOTE: Should the rotor come of f the stem, align groove in outer rim of rotor with groove in spline on the stem when reassemblin g. Also, if you
should wish to reverse hot for cold and cold for hot due to inst all error, or back to back inst allation, you can reassemble rot or 180° against stem
and valve will work properly.
Wall Type Showers
Column Type Showers
Escutcheon:
300-1139 (Individual)
300-1147 (Wall Saver)
300-1138 (Panelon
& Econowall)
24
1
2
3
20
4
23
24
1
2
21
4
Escutcheon Screws: (2)
160-278
22
5
12
6
7
8
Escutcheon Screws (2)
160-278
10
9
14
11
16
18
12
13
Figure 10a
19
15
Valves are equipped with a temperature limit stop which can be used to limit the
temperature of tempered water discharged. To adjust the temperature, remove the
handle and loosen the set screw. Remove the limit stop and reposition to desired
setting. Turn the limit stop clockwise for a hotter setting and counterclockwise for a
cooler setting.
NOTE: When replacing the double face seals, lubricate the top face with a small
amount of lubricant reassembling.
Escutcheon:
150-093 (6 person)
150-092 (2-5 person)
(NOTE: These parts have
a satin finish with etched
lettering)
17
to March, 2002
NOTE: This page is for
Equa-Flo Shower Valve
PRIOR
When assembling cap into valve body, use lubricant on 269-031 O-ring to prevent
twisting of O-ring.
If lubricant is not available, a slight film of soap may be used.
16
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo Shower Valve Parts List, Version Prior to March, 2002
Assembly
Item
Part No.
Description
1
2
125-055
S55-009
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
118-145
125-081
120-042
120-133
135-018
125-053
125-001BH
269-031
107-280
160-142
107-279
125-001CY
144-041
144-033
160-252
128-047
160-214
125-001BS
118-143
169-269
169-256
173-015
S27-102
Square Ring (In Rear)
Sleeve & Flapper
(Ear must fit into groove)
Cartridge Housing
Double-face Seal
Rotor
Stem
Spring
Washer
O-Ring
O-Ring
Cap/Clamp
Screws
Cover
O-Ring
OFF Stop
Hot Limit Stop
Set Screw
Handle
Screw
Gasket
Valve Body
Top Seat Gasket
Screws
Screens (Internal)
Stops (Optional)
Cartridge S
Assembly
S67-359
tem
Assembly
S21-065
(Figure 10)
Gasket
Repair Kit
S65-073
Qty
2
2
2
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
4
2
2
1
1
Complete Column Valve Replacement for columns built prior to March, 2002:
S65-075
S65-076
for 2-5 Person
for 6-person
NOTE: This page is for
Equa-Flo Shower Valve
PRIOR to March, 2002
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
17
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo Shower Valve, March, 2002 to July, 2004
(Figure 10)
For Individual, Econo-Walls, Wall Savers, Panelons and Column Showers
NOTE: Should the rotor come of f the stem, align groove in outer rim of rotor with groove in spline on the stem when reassemblin g. Also, if you
should wish to reverse hot for cold and cold for hot due to inst all error, or back to back inst allation, you can reassemble rot or 180° against stem
and valve will work properly.
Wall Type Showers
Column Type Showers
Escutcheon:
300-1140 (Individual & Econowall)
300-1141 (Panelon)
300-1147 (Wall Saver)
24
1
2
3
20
4
23
24
1
2
21
4
Escutcheon Screws: (2)
160-142
22
5
12
6
7
8
Escutcheon Screws (2)
160-278
10
9
14
11
16
18
12
13
Figure 10a
19
15
Escutcheon:
150-206 (6 person)
150-205 (2-5 person)
(NOTE: These parts have
a chrome finish with
cast-in recessed lettering)
17
Valves are equipped with a temperature limit stop which can be used to limit the
temperature of tempered water discharged. To adjust the temperature, remove the
handle and loosen the set screw. Remove the limit stop and reposition to desired
setting. Turn the limit stop clockwise for a hotter setting and counterclockwise for a
cooler setting.
NOTE: When replacing the double face seals, lubricate the top face with a small
amount of lubricant reassembling.
NOTE: This page is for
Equa-Flo Shower Valve
March, 2002 to July, 2004
When assembling cap into valve body, use lubricant on 269-031 O-ring to prevent
twisting of O-ring.
If lubricant is not available, a slight film of soap may be used.
18
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo Shower Valve Parts List, March, 2002 to July, 2004
Assembly
Item
Part No.
Description
1
2
125-055
S55-009
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
118-145
125-081
120-042
120-133
135-018
125-053
125-001BH
269-031
107-280
160-142
107-279
125-001CY
144-041
144-033
160-252
128-161
160-214
125-001BS
118-143
169-269
169-256
173-015
S27-102
Square Ring (In Rear)
Sleeve & Flapper
(Ear must fit into groove)
Cartridge Housing
Double-face Seal
Rotor
Stem
Spring
Washer
O-Ring
O-Ring
Cap/Clamp
Screws
Cover
O-Ring
OFF Stop
Hot Limit Stop
Set Screw
Handle
Screw
Gasket
Valve Body
Top Seat Gasket
Screws
Screens (Internal)
Stops (Optional)
Cartridge S
Assembly
S67-359
tem
Assembly
S21-065
(Figure 10)
Gasket
Repair Kit
S65-073
Qty
2
2
2
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
4
2
2
1
1
Complete Column Valve Replacement for columns built March, 2002 to July , 2004:
S65-235
S65-236
for 2-5 Person
for 6-person
NOTE: This page is for
Equa-Flo Shower Valve
March, 2002 to July, 2004
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
19
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Adjusting the Equa-Flo™ Valve (Figure 10)
NOTE: The maximum temperature limit stop has been preset by the factory for maximum temperature
operation. For temperatures other than the maximum, the stop may be repositioned as shown below.
IMPORTANT: Failure to adjust the maximum temperature limit stop to a safe shower temperature, no more than 105°F, could result in the user being
scalded.
1. Loosen the setscrew in the bottom of the hot limit stop.
2. Remove the outermost stop and reposition to the desired temperature setting (see Figure 10b).
NOTE: Do not remove the inner off-stop.
A. Position the Temperature Limit Stops as shown for Individual Wall Showers.
B. Position the Temperature Limit Stops as shown for Wall-Savers, Panelons and Econo-Walls.
C. Position the Temperature Limit Stops as shown for Column Showers.
Figure 10b
3. If the desired position falls between adjacent positions on the spline, flip the stop over so that the
other face shows. This shifts the stop position by 1/2 spline.
FOR BACK-TO-BACK INSTALLATION: On the valve that is installed "backwards," rotate the
stem 180° so that the "groove in spline" is opposite that shown for tub and shower valves (see
Figure 10c).
ESCUTCHEON
TO SHOWERHEAD
15
18
19
FOR BACK-TO-BACK
INSTALLATION ONLY
(GROOVE
IN SPLINE)
Figure 10c
20
17
16
TUB & SHOWER
VALVES
WALL-SAVER
VALVES
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Equa-Flo Pressure Balancing Valve, August 2004 to Present
For Individual, Econo-Walls, Wall Savers and Panelons Showers
10
ESCUTCHEON:
300-1140(INDIVIDUAL EF & ECONO-WALL)
300-1141(PANELON)
300-1147 (WALL SAVER) AUGUST 2004 TO PRESENT
2
4
7
6
HANDLE
(INDIVIDUAL EF)
128-161
1
ESCUTCHEON
(INDIVIDUAL C5)
150-219
3
9
5
HANDLE
(INDIVIDUAL C5)
128-174
8
ESCUTCHEON SCREWS (2)
160-142 (ECONO-WALL, PANELON, WALL SAVER)
160-279 (INDIVIDUAL)
BACK-TO-BACK
INSTALLATION
TO
SHOWERHEAD
OFF
STOP
ARROW
ON CAP
HOT
LIMIT
STOP
UP
ALIGNMENT
MARK
UP
ARROW
ON CAP
SET
SCREW
Equa-Flo valves are equipped with a temperature limit stop which can be used to limit the temperature of tempered water dischar ged.
IMPORTANT:
The hot limit stop as shown above has been set for maximum temperature operation. For temperatures
other than the maximum, the stop may be repositioned as described below . Failure to adjust the hot limit
stop to a safe shower temperature could result in the user being scalded.
To adjust the temperature, remove the handle and loosen the set screw . Remove the HOT limit stop and reposition to desired sett ing. Turn the
limit stop clockwise for a HOTTER setting and counterclockwise for a COOLER setting.
When assembling the cartridge assembly into the valve body and cap, lubricate the stem and O-rings with S45-125 grease.
If the desired position falls between adjacent positions on the spline, flip the HOT limit stop over so the other face shows. This shifts the stop
position by 1/2 spline.
FOR BACK-TO-BACK INSTALLATION: On the valve that is inst alled “backwards”.
A. Remove (2) screws that hold down cap.
B. Rotate cap and cartridge assembly 180°; re-inst all screws.
C. Remove both limit stops and rotate 180°. Align with Alignment Mark as shown.
D. Adjust hot limit stop the same as for a st andard installation.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
21
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo Pressure Balancing Valve Parts List (August, 2004 to Present)
Individual, Econo-Walls, Wall Savers and Panelons
Assembly
Item
1
2
3
4
5
6
7
8
9
10
Part No.
118-144
269-1785
125-161
107-551
160-454
144-041
144-033
160-252
160-214
S27-102
Description
Valve Body
Cartridge Assembly
O-Ring
Cap
Screw 10-24 x 3/8 Flat Head
Limit Stop, OFF
Limit Stop, HOT
Set Screw 8-32 x 1/4
Screw 10-24 x 1 Flat Head
Check Stop
Gasket
Repair Kit
S65-276
Cartridge Assy.
Repair Kit
S65-277
Qty
1
1 (See Note 4)
—
1
2
1
1
1
1
2
—
—
1 (See Note 3)
—
—
—
—
—
—
—
—
1 (See Note 4)
1 (See Note 4)
—
—
—
—
—
—
—
Notes:
1. Complete Valve Replacement/Retrofit Kit:
S65-265
Individual and Econo-Wall Showers
S65-265A Panelon
S65-265B Wall Saver
Kit part numbers contain all parts necessary to replace/retrofit one station only .
Customer must order proper amount of kits; example:
Three S65-265 kits required for a 3W Econo-W all Shower.
2. Part numbers on this page apply only to Equa-Flo valves built from1983 to Present;
Equa-Flo valves built prior to 1983 must use S65-092 Retrofit Kit.
3. Gasket Repair kit also contains the three external O-rings (not shown on exploded
diagram) supplied with the 269-1785 cartridge assembly .
4. If the 269-1785 Cartridge is disassembled, it cannot be reassembled and must be
replaced. The 269-1785 Cartridge assembly cannot be ordered separately; cartridge
assembly must be ordered as part of the Repair Kit that includes the O-ring.
22
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo Pressure Balancing Valve (August, 2004 to Present)
For Column Showers
UP
Position of Arrow on Cap
Shower
Manifold
Valve shown in "OFF" position
with HOT limit stop shown set
for maximum temperature operation.
11
Notch in Stem
9
12
10
13
Escutcheon:
150-206 (6 Person)
150-205 (2-5 Person)
(Note: These parts have
a chrome finish with
cast-in recessed lettering)
8
1
6
7
5
2
3
4
Escutcheon Screws (2)
160-278
Equa-Flo valves are equipped with a temperature limit stop which can be used to limit the temperature of tempered water dischar ged.
IMPORTANT:
The hot limit stop as shown above has been set for maximum temperature operation. For temperatures
other than the maximum, the stop may be repositioned as described below . Failure to adjust the hot limit
stop to a safe shower temperature could result in the user being scalded.
To adjust the temperature, remove the handle and loosen the set screw . Remove the HOT limit stop and reposition to desired sett ing. Turn the
limit stop clockwise for a HOTTER setting and counterclockwise for a COOLER setting.
When assembling the cartridge assembly into the valve body and cap, lubricate the stem and O-rings with S45-125 grease.
If the desired position falls between adjacent positions on the spline, flip the HOT limit stop over so the other face shows. This shifts the stop
position by 1/2 spline.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
23
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo Pressure Balancing Valve Parts List (August, 2004 to Present)
Column Showers
Assembly
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
Part No.
128-161
160-214
144-033
160-252
144-041
160-454
107-551
125-161
269-1785
169-256
118-143
169-269
125-001BS
Description
Handle
Screw #10-24 x 1 Flat Head
Limit Stop, HOT
Set Screw #8-32 x 1/4
OFF Stop
Screw #10-24 x 3/8 Flat Head
Cap
O-Ring
Cartridge Assembly
Screw #10-24 x 5/8
Valve Body
Gasket
Washer
Gasket
Repair Kit
S65-278
Cartridge Assy.
Repair Kit
S65-277
Qty
1
1
1
1
1
2
1
1
1
4
1
1
1
—
—
—
—
—
—
—
1 (See Note 2)
—
—
—
1 (See Note 2)
1 (See Note 2
—
—
—
—
—
—
—
1 (See Note 3)
1 (See Note 3)
—
—
—
—
Notes:
1. Complete Column Valve Replacement/Retrofit Kit:
S65-266
for 2-5 Person
S65-267
for 6 Person
Kit part numbers contain all parts necessary to replace/retrofit one station only .
Customer must order proper amount of kits; example:
Five S65-266 kits required for a 5 Person Column Shower .
2. Gasket Repair kit also contains the three external O-rings (not shown on exploded
diagram) supplied with the 269-1785 cartridge assembly .
3. 269-1785 Cartridge assembly cannot be ordered separately; cartridge assembly
must be ordered as part of the Repair Kit that includes the O-ring.
24
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo HD Pressure Balancing Valve
For Individual, Econo-Walls, Wall Savers and Panelons Showers (2003 to Present)
UP
19
Set Screw
13
15
18
14
19
11
Align Item 5, Valve Cap
to Item 18, Valve Body
as shown
17
(Introduced
February 2007)
Escutcheon:
300-1140 (Individual & Econowall)
300-1141 (Panelon)
300-1147 (Wall Saver) August 2004 to Present
12
16
20
8
1
10
9
6
4
5
8
7
3
Escutcheon Screws (2)
160-142
2
Valves are equipped with a temperature limit stop which can be used to limit the
temperature of tempered water discharged. To adjust the temperature, remove the
handle and adjust the set screw on the valve cap. Turn the set screw clockwise for
COLDER setting and counterclockwise for W ARMER setting.
NOTE: When replacing the double face seals, lubricate the top face with a small
amount of lubricant when reassembling.
When assembling the valve cap into valve body , use lubricant on 125-154 O-ring to
prevent twisting of O-ring.
If lubricant is not available, a slight film of soap may be used.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
25
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo HD Pressure Balancing Valve Parts List
Individual, Econo-Walls, Wall Savers and Panelons (2003 to Present)
Assembly
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
128-163
160-226
160-225
160-441
107-521
125-154
125-001AY
142-131
135-089
120-150
120-155A
125-081
118-311
153-428
125-001BQ
119-242
125-155
118-144
S27-102
142-130
Handle
Screw
Screw
Set Screw
Valve Cap
O-Ring
O-Ring
Washer
Spring
Stem
Rotor
Double-Face Seal
Cartridge Housing
Retainer
O-Ring
Piston
O-Ring
Valve Body
Stops (Optional)
Washer
Cartridge S
Assembly
S67-602S
tem
Assembly
S21-076
Gasket
Repair Kit
S65-248
Qty
1
1
2
1
1
1
—
—
—
—
1
—
—
—
—
—
—
1
2
—
—
—
—
—
—
—
—
—
—
—
—
2
1
2
2
1
2
—
—
2
—
—
—
—
—
—
1
2
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
—
—
—
—
2
—
—
2
—
2
—
—
2
Complete Valve Replacement/Retrofit Kit:
S65-249
Individual and Econowall Showers
S65-249A
Panelon
S65-249B
Wall Saver
NOTE: Above part numbers contain all parts necessary to
replace/retrofit one station only. Customer must order
proper amount of kits; example:
Three S65-249 kits required for a 3W Econo-W all Shower.
26
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo HD Pressure Balancing Valve
For Column Showers (2003 to Present)
UP
Set Screw
16
Shower
Manifold
14
13
15
Align Item 5, Valve Cap
to Item 19, Valve Body
as shown
Escutcheon:
150-206 (6 Person)
150-205 (2-5 Person)
(Note: These parts have
a chrome finish with
cast-in recessed lettering)
19
12
22
(Introduced
February 2007)
11
18
20
21
17
8
1
10
8
5
7
9
3
4
2
6
Escutcheon Screws (2)
160-278
Valves are equipped with a temperature limit stop which can be used to limit the
temperature of tempered water discharged. To adjust the temperature, remove the
handle and adjust the set screw on the valve cap. Turn the set screw clockwise for
COLDER setting and counterclockwise for W ARMER setting.
NOTE: When replacing the double face seals, lubricate the top face with a small
amount of lubricant when reassembling.
When assembling the valve cap into valve body , use lubricant on 125-154 O-ring to
prevent twisting of O-ring.
If lubricant is not available, a slight film of soap may be used.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
27
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Equa-Flo HD Pressure Balancing Valve Parts List
Column Showers (2003 to Present)
Parts List
Assembly
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
128-163
160-226
160-225
160-441
107-521
125-154
125-001AY
142-131
135-089
120-150
120-155B
125-081
118-311
153-428
125-001BQ
119-242
125-155
169-256
118-143
169-269
125-001BS
142-130
Handle
Screw
Screw
Set Screw
Valve Cap
O-Ring
O-Ring
Washer
Spring
Stem
Rotor
Double-Face Seal
Cartridge Housing
Retainer
O-Ring
Piston
O-Ring
Screw
Valve Body
Gasket
Washer
Washer
Cartridge S
Assembly
S67-602S
tem
Assembly
S21-076
Gasket
Repair Kit
S65-248A
Qty
1
1
2
1
1
1
—
—
—
—
1
—
—
—
—
—
—
4
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
2
1
2
2
1
2
—
—
—
—
2
—
—
—
—
—
—
1
2
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
—
—
—
—
2
—
—
2
—
2
—
—
1
1
2
Complete Column Valve Replacement/Retrofit Kits for columns:
S65-250
S65-251
for 2-5 Person
for 6-person
NOTE: Above part numbers contain all parts necessary to replace/retrofit one
station only. Customer must order proper amount of kits; example:
Five S65-250 kits required for a five person column.
28
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2005 (April, 2003 to Present)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
UP
25
23
22
20
18
16
14
12
24
21
10
19
17
15
13
ORIENT ITEM 4, CAP
RELATIVE TO ITEM 24,
VALVE BODY AS SHOWN
ESCUTCHEON:
300-1144 (INDIVIDUAL
& ECONOWALL)
300-1145 (PANELON)
300-1146 (WALL SAVER)
APRIL 2003 TO JANUARY 2006
300-1148 (WALL SAVER)
FEBRUARY 2006 TO PRESENT
11
9
8
6
1
4
7
5
3
2
ESCUTCHEON SCREWS (2)
160-279
To adjust the valve's temperature to other than the factory preset, follow the procedures outlined below.
1. Turn on the water and let it run until 2.5 – 4 GPM is flowing through the
valve.
2. Remove the shower valve handle and handle screw to expose the set
screw inside the valve stem.
3. Using a 3/32" hex-head Allen key, turn the set screw counterclockwise to
increase the temperature or clockwise to decrease the temperature.
4. When the adjustment is complete, replace the handle and turn of f the
water.
NOTE: When replacing the double face seals, lubricate the top face with a
small amount of lubricant when reassembling.
NOTE: The maximum temperature for this
valve has been set to approximately 110° F
with an incoming hot water temperature of
140° F. This maximum temperature may need
to be adjusted based on the installation conditions or application. See Figure below
for adjustment.
When assembling the valve cap into valve body , use lubricant on 125-154
O-ring to prevent twisting of O-ring.
If lubricant is not available, a slight film of soap may be used.
VALVE SHOWN WITH HANDLE AND
ESCUTCHEON REMOVED FOR CLARITY
SET SCREW
OPTIONAL
STOP/CHECK
COVER SCREWS
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
29
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2005 (April, 2003 to Present)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
Parts List
Assy.
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
128-163
160-226
160-225
107-519
125-154
153-427
125-001CD
120-152
160-408
125-001CM
153-404
142-112
153-406
S39-413
132-044
153-405
135-085
119-245
142-129
160-407
135-074
144-065
125-155
118-144
S27-102
Handle
Set Screw 10-24 x 5/16
Flat Screw 10-24 x 3/4
Cap, TMV-Shower
O-Ring
Retainer, Shower TMV
O-Ring
Stem, Shower TMV
Set Screw 10-24 x 1-1/4
O-Ring
Holder-Shutoff Disk
Disk-Shutoff
Retainer-Shutoff Disk
Thermostat
Retaining Ring
Retainer-Overheat Spring
Spring
Piston
Seal Disk - Hot
Screw 6-32 x 3/16
Spring
Liner, TMV-Shower
O-Ring
Valve Body
Stops (Optional)
Piston Seat
Thermostat Piston/Liner O-Ring/Seat
Assembly Assembly
Kit
Kit
Kit
S64-094
S86-006
S65-257
S65-253
S65-252
Qty
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
—
—
—
—
—
—
—
—
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
1
1
1
1
2
—
—
—
—
—
—
1
—
1
—
—
1
1
1
1
—
—
—
—
—
—
—
—
—
2
—
—
Complete Valve Replacement/Retrofit Kit:
S65-254
Individual and Econowall Showers
S65-254A
Panelon
S65-254B
Wall Saver
NOTE: Above part numbers contain all parts necessary to
replace/retrofit one station only. Customer must order
proper amount of kits; example:
Three S65-254 kits required for a 3W Econo-W all Shower.
30
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2005 (April, 2003 to Present)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
Thermostatic Mixing Valve Maintenance
For maximum efficiency, your thermostatic mixing valve requires a minimum amount of maintenance. Follow
the procedures outlined below to achieve highest performance.
Check the piston for smooth movement
To check the valve's piston for free and smooth movement, follow the procedures outlined below:
1. Remove the handle and escutcheon to expose the valve assembly.
2. Loosen the two screws that hold the valve assembly in the valve body.
3. Remove the valve assembly.
4. Gently pry the retainer off the valve assembly. This will separate the cap and liner exposing other
components.
5. Disassemble components as shown below.
6. Push in on the piston with your finger (the piston should move freely). If the movement is not as it
should be, the piston and liner assembly needs to be cleaned.
• any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable cleaner is not
sufficient to remove debris, a 400-grit sandpaper may be used to polish and hone the piston and liner).
7. Reassemble the valve assembly in reverse manner.
8. If, after a thorough cleaning, the piston does not move freely, the piston/liner assembly must be
replaced. Order a new Piston/Liner Assembly as specified in the parts list.
VALVE BODY
SPRING
PISTON
(PUSH IN, THEN RELEASE
TO CHECK FOR SMOOTH MOVEMENT)
LINER
THERMOSTAT
PUSHROD
SEAT ASSEMBLY
PISTON ASSEMBLY
THERMOSTAT
RETAINER
CAP WITH
STEM
NOTE: Arrow on cap
must point to HOT side.
SCREWS
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
31
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2005 (April, 2003 to Present)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
Thermostatic Mixing Valve Maintenance continued . . .
Check the thermostat for proper operation
To check the valve's thermostat for proper operation, follow the procedure outlined below.
1. At room temperature (80° F or less), remove the valve assembly from the valve body as outlined in the
previous section detailing piston movement.
2. Place the thermostat into a small container filled with 115° water. The thermostat’s pushrod should pop
out of the thermostat approximately 1/10".
3. If the pushrod does not pop out, the thermostat must be replaced (it cannot be repaired). Order a new thermostat kit as specified in the parts list.
Thermostatic Mixing Valve Troubleshooting
NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions:
• if optional stop/check valves are used, make sure that they are fully open
and that all inlet and outlet shut-off valves are open.
• make sure that the hot and cold inlet pipes are connected properly, and that there are no crossconnections or leaking stop/check valves.
• check the hot water heater output to make sure that it is at least 15° F above the set temperature.
Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the
valves after inspection and repair is complete.
Problem: Limited water flow
Cause: The optional stop/check sections of the valve do not move freely.
Solution: Dirt and debris have collected on the stop/check valve seat limiting the movement of the
stop/checks. The stop/checks should be disassembled and cleaned. The components may be brushed
with a small wire brush to remove debris. If the optional stop/check valves need to be replaced, contact your Bradley representative and ask for Stop/Check Valve (part number S27-102).
Problem: External leaks in the system
Cause: Either the NPT joints or O-rings have been damaged.
Solution: Replace the NPT joints and/or O-rings where necessary. For replacement of the O-rings, order the
O-ring/Seat kit as specified in the included parts list.
Problem: Improper water temperature or temperature fluctuation
Cause: Thermostat is slowly failing or not working at all.
Solution: See "Check the thermostat for proper operation" and follow the step-by-step procedure.
Cause: Valve temperature is not properly set.
Solution: See "Adjusting the temperature" found on 215-1369-28 (1 of 4) and follow the step-by-step procedure.
Cause: Inlet supply line to the mixing valve is being shared by other pieces of equipment that are used only
periodically, such as laundry appliances or washdown stations. It may reduce the inlet pressure to the
mixing valve to less than 3 PSI. The supply line size may not be large enough to supply both the valve
and the other appliances.
Solution: Enlarge the supply line size, reconfigure the supply line or regulate the supply usage.
32
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve
For Column Showers
SHOWER
MANIFOLD
27
24
20
ORIENT ITEM 4, CAP
RELATIVE TO ITEM 24, 17
VALVE BODY
AS SHOWN
16
22
19
26
25
15
23
21
18
ESCUTCHEON:
150-206 (6 PERSON)
150-205 (2-5 PERSON)
(NOTE: THESE PARTS HAVE
A CHROME FINISH WITH
CAST-IN RECESSED
LETTERING)
14
10
13
12
1
8
7
11
9
6
5
4
3
2
ESCUTCHEON
SCREWS (2)
160-278
To adjust the valve's temperature to other than the factory preset, follow the procedures outlined below.
1. Turn on the water and let it run until 2.5 – 4 GPM is flowing through the
valve.
2. Remove the handle and handle screw to expose the set screw inside the
valve stem.
3. Using a 3/32" hex-head Allen key, turn the set screw counterclockwise to
increase the temperature or clockwise to decrease the temperature.
4. When the adjustment is complete, replace the handle and turn of f the
water.
NOTE: When replacing the double face seals, lubricate the top face with a
small amount of lubricant when reassembling.
NOTE: The maximum temperature for this
valve has been set to approximately 110° F
with an incoming hot water temperature of
140° F. This maximum temperature may need
to be adjusted based on the installation conditions or application. See Figure below
for adjustment.
When assembling the valve cap into valve body , use lubricant on 125-154
O-ring to prevent twisting of O-ring.
If lubricant is not available, a slight film of soap may be used.
VALVE SHOWN WITH HANDLE AND
ESCUTCHEON REMOVED FOR CLARITY
SET SCREW
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
33
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve
For Column Showers
Parts List
Assy.
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
128-163
160-226
160-225
107-519
125-154
153-427
125-001CD
120-152
160-408
125-001CM
153-404
142-112
153-406
S39-413
132-044
153-405
135-085
119-245
142-129
160-407
135-074
144-065
125-155
169-256
118-143
169-269
125-001BS
Handle
Set Screw 10-24 x 5/16
Flat Screw 10-24 x 3/4
Cap, TMV-Shower
O-Ring
Retainer, Shower TMV
O-Ring
Stem, Shower TMV
Set Screw 10-24 x 1-1/4
O-Ring
Holder-Shutoff Disk
Disk-Shutoff
Retainer-Shutoff Disk
Thermostat
Retaining Ring
Retainer-Overheat Spring
Spring
Piston
Seal Disk - Hot
Screw 6-32 x 3/16
Spring
Liner, TMV-Shower
O-Ring
Screw
Valve Body
Gasket
Washer
Piston Seat
Thermostat Piston/Liner O-Ring/Seat
Assembly Assembly
Kit
Kit
Kit
S64-094
S86-006
S65-257
S65-253
S65-252A
Qty
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
—
—
—
—
—
—
—
—
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
1
1
1
1
2
—
—
—
—
—
—
—
—
1
—
1
—
—
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
1
1
Complete Valve Replacement/Retrofit Kit for columns:
S65-255
for 2-5 Person
S65-256
for 6-Person
NOTE: Above part numbers contain all parts necessary to
replace/retrofit one station only. Customer must order
proper amount of kits; example:
Five S65-255 kits required for a five person column.
34
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve
For Column Showers
Thermostatic Mixing Valve Maintenance
For maximum efficiency, your thermostatic mixing valve requires a minimum amount of maintenance. Follow
the procedures outlined below to achieve highest performance.
Check the piston for smooth movement
To check the valve's piston for free and smooth movement, follow the procedures outlined below:
1. Remove the handle and escutcheon to expose the valve assembly.
2. Loosen the two screws that hold the valve assembly in the valve body.
3. Remove the valve assembly.
4. Gently pry the retainer off the valve assembly. This will separate the cap and liner exposing other
components.
5. Disassemble components as shown below.
6. Push in on the piston with your finger (the piston should move freely). If the movement is not as it
should be, the piston and liner assembly needs to be cleaned.
• any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable cleaner is not
sufficient to remove debris, a 400-grit sandpaper may be used to polish and hone the piston and liner).
7. Reassemble the valve assembly in reverse manner.
8. If, after a thorough cleaning, the piston does not move freely, the piston/liner assembly must be
replaced. Order a new Piston/Liner Assembly as specified in the parts list.
VALVE
MANIFOLD
PISTON
(PUSH IN, THEN RELEASE
TO CHECK FOR SMOOTH MO VEMENT)
SPRING
LINER
THERMOSTAT
PUSHROD
SEAT ASSEMBLY
PISTON ASSEMBLY
RETAINER
THERMOSTAT
CAP WITH
STEM
SCREWS
NOTE: Arrow on cap
must point UP.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
35
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve
For Column Showers
Thermostatic Mixing Valve Maintenance continued . . .
Check the thermostat for proper operation
To check the valve's thermostat for proper operation, follow the procedure outlined below.
1. At room temperature (80° F or less), remove the valve assembly from the valve body as outlined in the
previous section detailing piston movement.
2. Place the thermostat into a small container filled with 115° water. The thermostat’s pushrod should pop
out of the thermostat approximately 1/10".
3. If the pushrod does not pop out, the thermostat must be replaced (it cannot be repaired). Order a new
thermostat kit as specified in the parts list.
Thermostatic Mixing Valve Troubleshooting
NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions:
• make sure all inlet and outlet shut-off valves are open.
• make sure that the hot and cold inlet pipes are connected properly, and that there are no crossconnections or leaking stop valves.
• check the hot water heater output to make sure that it is at least 15° F above the set temperature.
Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the
valves after inspection and repair is complete.
Problem: External leaks in the system
Cause: Either the NPT joints or O-rings have been damaged.
Solution: Replace the NPT joints and/or O-rings where necessary. For replacement of the O-rings, order the
O-ring/Seat kit as specified in the included parts list.
Problem: Improper water temperature or temperature fluctuation
Cause: Thermostat is slowly failing or not working at all.
Solution: See "Check the thermostat for proper operation" and follow the step-by-step procedure.
Cause: Valve temperature is not properly set.
Solution: See "Adjusting the temperature" found on 215-1369-28A (1 of 4) and follow the step-by-step procedure.
Cause: Inlet supply line to the mixing valve is being shared by other pieces of equipment that are used only
periodically, such as laundry appliances or washdown stations. It may reduce the inlet pressure to the
mixing valve to less than 3 PSI. The supply line size may not be large enough to supply both the valve
and the other appliances.
Solution: Enlarge the supply line size, reconfigure the supply line or regulate the supply usage.
36
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2006 (2000 to April, 2003)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
3/8" TUBE CONNECTOR
145-025
140-920
VALVE MOUNTING BRACKET (2) PLACES
160-138
10-24 X 1/2" SCREW (2) PLACES
INDICATES COMPONENTS USED ON ECONOWALLS, PANELONS AND WALLSAVERS.
27
26
INDICATES COMPONENTS USED ON INDIVIDUAL (1C) SHOWERS ONLY.
28
30
25
31
20
24
22
17
19
16
29
27
23
15
21
18
LABEL
204-509 (INDIVIDUAL &
WALLSAVER)
204-509A (ECONOWALL &
PANELON)
169-168
1/2"
PIPE PLUG
6
14
7
4
13
12
2
11
10
9
8
5
1
3
140-921
ESCUTCHEON MOUNTING BRACKET
160-138
10-24 X 1/2" SCREW (2) PLACES
ESCUTCHEON
150-074 (INDIVIDUAL, ECONOWALL & PANELON)
150-083 (WALLSAVER)
SCREWS
160-142 (ECONOWALL, PANELON & WALLSAVER)
160-177 (INDIVIDUAL)
To adjust the valve's temperature to other than the factory preset, follow the procedures outlined below.
1. Turn on the water and let it run until 2.5 – 4 GPM is flowing through the
valve.
2. Remove the shower valve handle and handle screw to expose the set
screw inside the valve stem.
3. Using a 3/32" hex-head Allen key, turn the set screw counterclockwise to
increase the temperature or clockwise to decrease the temperature.
4. When the adjustment is complete, replace the handle and turn of f the
water.
NOTE: The maximum temperature for this
valve has been set to approximately 105° F
with an incoming hot water temperature of
140° F. This maximum temperature may need
to be adjusted based on the installation conditions or application.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
37
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2006 (2000 to April, 2003)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
Parts List
Assembly
S59-2006
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
38
Part No.
Description
160-225
128-078
160-177
204-509
150-074
107-279
110-228A
142-113
160-408
160-392
107-504
125-001CD
120-148A
125-109
125-001CM
153-404
142-112
153-406
S39-413
132-044
153-405
135-085
119-236
135-074
142-129
160-407
144-059
125-001DA
125-150
118-287
S27-102
Flat Screw 10-24 x 3/4
Handle
BTN Screw 10-24 x 1-1/8
Label
Escutcheon
Cover
Nut
Mounting Plate
Set Screw 10-24 x 1-1/4
Screw 1/4-20 x 3/8
Cap
O-Ring
Stem, Shower TMV
O-Ring
O-Ring
Holder - Shutoff Disk
Shutoff Disk
Retainer - Shutoff Disk
Thermostat
Retaining Ring
Retaining - Overheat Spring
Spring
Piston
Spring
Seal Disc - Hot
Screw 6-32 x 3/16
Liner
O-Ring
O-Ring
Valve Body
Stops (Optional)
Piston/Liner
Kit
S65-205
Cover
Kit
S65-206
Thermostat O-Ring/Seal
Kit
Kit
S65-201
S65-202
Qty
1
1
2
1
1
1
1
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
—
—
—
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
—
1
1
—
—
—
—
—
—
—
—
—
1
—
—
1
1
—
—
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2006 (2000 to April, 2003)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
Thermostatic Mixing Valve Maintenance
For maximum efficiency, your thermostatic mixing valve requires a minimum amount of maintenance. Follow
the procedures outlined below to achieve highest performance.
Check the piston for smooth movement
To check the valve's piston for free and smooth movement, follow the procedures outlined below:
1. Remove the valve’s top cap and thermostat.
2. Push in on the piston with your finger (the piston should move freely). If the movement is not as it
should be, the piston and liner assembly needs to be cleaned.
• remove the cap and thermostat
• using a 7/8" socket wrench, loosen the piston/liner assembly from the valve body and lift the
assembly out with a needle-nose pliers.
• disassemble the piston/liner assembly components as shown in the figure below.
• any cleaner suitable for brass and stainless steel may be used (if cleaning with suitable cleaner is not
sufficient to remove debris, a 400-grit sandpaper may be used to polish and hone the piston and
liner).
• reassemble the valve assembly in reverse manner and retest the piston.
3. If, after a thorough cleaning, the piston does not move freely, the piston/liner assembly must be
replaced. Order a new Piston/Liner Assembly as specified in the parts list.
SPRING
PISTON ASSEMBLY
(PUSH IN, THEN RELEASE
TO CHECK FOR SMOOTH
MOVEMENT)
VALVE BODY
LINER
SEAT
ASSEMBLY
TOP CAP
PLATE
THERMOSTAT
PUSHROD
THERMOSTAT
STEM
SCREWS
ADJUSTMENT SET SCREW
LOCATED INSIDE STEM
NUT
COVER
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
39
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Thermostatic Mixing Valve – Model S59-2006 (2000 to April, 2003)
For Individual, Econo-Wall, Wall Saver and Panelon Showers
Thermostatic Mixing Valve Maintenance continued . . .
Check the thermostat for proper operation
To check the valve's thermostat for proper operation, follow the procedure outlined below.
1. At room temperature (80° F or less), remove the top cap and thermostat as outlined in the previous section detailing piston movement.
2. Place the thermostat into a small container filled with 115° water. The thermostat’s pushrod should pop
out of the thermostat approximately 1/10".
3. If the pushrod does not pop out, the thermostat must be replaced (it cannot be repaired). Order a new
thermostat kit as specified in the parts list.
Thermostatic Mixing Valve Troubleshooting
NOTE: Before attempting to troubleshoot the valve or disassemble the components, check for the
following conditions:
• if optional stop/check valves are used, make sure all inlet and outlet shut-off valves are open
(the slotted stem must extend out approximately 1/4" from the valve cap).
• make sure that the hot and cold inlet pipes are connected properly, and that there are no
cross-connections or leaking stop valves.
• check the hot water heater output to make sure that it is at least 15° F above the set temperature.
Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the
valves after inspection and repair is complete.
Problem: Limited water flow
Cause: The optional stop/check sections of the valve do not move freely.
Solution: Dirt and debris have collected on the stop/check valve seat limiting the movement of the stop/checks. The
stop/checks should be disassembled and cleaned. The components may be brushed with a small wire brush to
remove debris. If the optional stop/check valves need to be replaced, contact your Bradley representative and
ask for Stop/Check Valve (part number S27-102).
Problem: External leaks in the system
Cause: Either the NPT joints or O-rings have been damaged.
Solution: Replace the NPT joints and/or O-rings where necessary. For replacement of the O-rings, order the
O-ring/Seat kit as specified in the included parts list.
Problem: Improper water temperature or temperature fluctuation
Cause: Thermostat is slowly failing or not working at all.
Solution: See "Check the thermostat for proper operation" and follow the step-by-step procedure on the previous page.
Cause: Valve temperature is not properly set.
Solution: See "Adjusting the temperature" found on 215-1369-28B (1 of 4) and follow the step-by-step procedure.
Cause: Inlet supply line to the mixing valve is being shared by other pieces of equipment that are used only
periodically, such as laundry appliances or washdown stations. It may reduce the inlet pressure to the
mixing valve to less than 3 PSI. The supply line size may not be large enough to supply both the valve
and the other appliances.
Solution: Enlarge the supply line size, reconfigure the supply line or regulate the supply usage.
40
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Hand Held Shower
1
2
3
7
169-938
24" Deluxe
Slide Bar
(Not included
with S30-067
Hand Held
Shower Prepack)
4
6
5
Parts List
Hand Held
Shower Prepack
S30-067
Item
Part No.
Description
1
2
3
4
5
6
7
169-941
169-988
169-939
169-943
169-937
169-949
169-936
Supply Elbow w/Flange - HN
Back Flow Preventer
Quick Connector
Swivel Connector
S.S. Flex Hose - 60"
Wall Mount - Hand Shower
Hand Shower
Qty
1
1
1
1
1
1
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
41
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Diverter Valve – In Wall
1
2
4
3
Operation and Service Instructions
(Figure 11)
5
10
8
6
7
9
12
11
12
13
12
Parts List
Valve
Assembly
S27-185
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
269-1368
269-413
269-412
269-411
269-410
269-409
269-408
269-407
269-406
269-405
125-001DC
269-415
269-403
Index
Screw
Handle
Spindle Bushing
Collar
Escutcheon
Packing Nut
Packing
Washer
Hub
O-Ring
Repair Kit
Body
42
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
.
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.4
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Infrared Sensor
(Figure 12)
RED
LEAD
BLACK
LEAD
BLUE
LEAD
Infrared Sensor
S83-099
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
43
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Metering Air Valve
(Figure 13)
Manual
Release Button
3
2
Operation and Service Instructions
Air Valve Tubing
4
Locking Slope
5
6
7
8
Tube Connector
Gripping Edge
1
Center Hole
Sealing Ring
21
18
19
17
Timer
9
10
11
20
12
13
14
15
Figure 13
16
Parts List
Assembly
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
44
Part No.
Description
118-183
117-036
269-665
269-664
179-082
135-053
269-662
125-001DT
118-247
135-052
269-660
269-659
135-051
269-657
142-002CR
160-313
S27-254
269-656
269-1186
169-890
269-1188
215-913
Lower Valve Body
Valve Seat
Rubber Diaphragm
Plastic Disk
Stainless Steel Disk
Spring
Divider Plate
O-Ring
Air Valve Body
Spring for Magnet
Magnet Assembly
Air Diaphragm
Diaphragm Spring
Valve Cover
Lockwasher
Screw
Timer Assembly
Cover – Timer Assy.
Fitting — Adj. "L"
Tube Connector
Filter Washer (Inside Flex Hose)
Air Valve Instruction Sheet
Valve Kit
S65-110
Repair Kit
S73-054C
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Bradley Showers
Metering Air Valve Troubleshooting Instructions
(Figure 13)
How They Work
Refer to Figure 13.
1. A pulse of air is created at the air diaphragm by pressing the pushbutton.
2. The pulse of air travels through the 1/8" air tubing into the lower port on the valve, up through
the magnet (housed within Item 9) and diaphragm, and exits through the top cover of the valve.
3. Releasing the pushbutton draws all the air out of the valve creating a vacuum inside the valve.
4. The top diaphragm acts as a check and does not let any air enter the valve through the top cover.
5. The vacuum created allows the magnet to drop down in the valve, attracting the armature plate.
6. The rising armature plate allows the water pressure to push the seat diaphragm off the valve
seat.
7. Water flows through the seat and out to the sprayhead.
8. Air is pulled into the valve through the timer by the vacuum on the inside of the valve.
9. The incoming air breaks the vacuum on the inside of the valve (Item 9).
10. The amount of air entering the valve through the timer determines the metering cycle.
11. When the vacuum is eliminated, the magnet spring pushes the magnet back to its original position.
12. The armature plate drops down to its original position, pushing the seat diaphragm back down
on the seat closing the valve.
13. A small amount of water passes through the diaphragm to equalize the pressure on either side of
the diaphragm.
Adjust Air Valve Meter Time
NOTE: The air valve timer is located next to the tube connector on the air valve body. The timer is
capped with a filter to prevent dirt build-up on the timer. The air valve timing can be adjusting from 5–60
seconds.
1. Remove filter cap and use a screwdriver to tighten or loosen the timer (Figure 13). Turning the
timer clockwise increases the time; turning the timer counterclockwise decreases the time.
2. Continue to adjust until the timer is set at desired length.
3. Replace filter cap over the timer.
Tube Connection Leaks
1. Push in the white manual release button while pulling the tube out (see Figure 13) to disconnect
the tube at the tube fitting. No tools are needed.
2. To correct a leak, press tubing firmly into the tube fitting and make sure it is seated.
3. If leak persists, remove tubing from the fitting, and trim the tubing end square with a razor-sharp
knife. If leak continues, replace the fitting or contact your Bradley representative for assistance.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
45
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Metering Air Valve Troubleshooting Instructions
(Figure 13) continued...
Metering Air Valve Troubleshooting
Problem: Water is dripping from the streamformers
Cause: Debris on valve seat or orifices
Step 1: Clean and inspect valve seat
1. Remove screws and disassemble metering valve.
2. Clean valve seat and inspect for deep gouges or scratches. Replace if necessary.
3. Remove all debris that may be clogging center hole of the plastic diaphragm assembly and offcenter hole in the rubber diaphragm.
Problem: Valve will not shut off
Cause: Timing mechanism is clogged
Step 1: Clean timing mechanism
1. Blow water and debris from perforated metal sleeve of timing mechanism if compressed air is
available.
2. Turn the adjusting screw in all the way but do not force screw.
3. Turn adjusting screw out to desired cycle time.
Problem: Valve will not turn on
Cause: Water is not being supplied to unit
Step 1: Open all stops on the valve assembly
Problem: Timing cannot be adjusted for more than five seconds
Cause: There is an air leak
Step 1: Check assembly
1. Check all tubing and fittings for proper assembly.
2. Tighten all screws which hold valve together.
Problem: Pushbutton does not work properly
Cause: Air volume may not be sufficient to operate valve
Step 1: Check all fittings for air leaks
Problem: Valve cycles properly, but water does not form streams and drip s from
streamformer
Cause: Flow control is clogged or is not seated properly
Step 1: Inspect and clean air flow control assembly
1. Remove 1/4" tubing and 1/4" tube connector fitting from metering air valve (Figure 13).
2. Inspect flow control and remove debris that may be clogging assembly.
3. Replace fitting using Teflon™ tape on pipe threads.
4. Replace 1/4" tubing as follows: cut 1/4" from the end of the tube to make sure the end is square,
then insert into tube connector fitting.
46
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Metering Air Valve
(Figure 13a)
For Column Showers (1998 — 2000) V ersion
1/8" O.D. Air Tubing
R68-600008
(Specify Length
when Ordering)
S07-062A
Air valve,
See Sheet 3 for
Parts Information
269-881 Elbow
Tube Connector
5/16" O.D. Supply Tubing
R68-600015 (Specify Length
when Ordering)
269-881
Elbow Tube Connector
169-076A
1/2" x 3/8"
Reducer
169-215
3/8" x 1/4"
Reducer
6-Person manifold shown.
Manifold will vary depending on showerhead
configuration. Parts identified are typical for
2-6 person columns with metering air valve.
Contact Bradley Representative for part
numbers not listed.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
47
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Metering Air Valve
Operation and Service Instructions
(Figure 13b)
For Column Showers (2000 — Present) V ersion
5/16" O.D. Supply Tubing
R68-600015
(Specify Length
when Ordering)
1/8" O.D. Air Tubing
R68-600008 (Specify
Length when Ordering)
S07-065
Air valve,
See Sheet 3 for
Parts Information
113-1077
Nipple
269-881 Elbow
Tube Connector
269-1674
3/8" x 1/4"
Street Elbow
6-Person manifold shown.
Manifold will vary depending on showerhead
configuration. Parts identified are typical for
2-6 person columns with metering air valve.
Contact Bradley Representative for part
numbers not listed.
48
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Metering Air Valve
2
(Figure 13c)
Manual
Release Button
3
Air Valve Tubing
4
Locking Slope
5
6
7
8
Tube Connector
Gripping Edge
1
Center Hole
Sealing Ring
18
19
1
17
Timer
9
10
11
20
12
13
14
15
Figure 13c
16
Parts List
Assembly
Item
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Part No.
Description
118-183
118-226
117-036
269-665
269-664
179-082
135-053
269-662
125-001DT
118-247
135-052
269-660
269-659
135-051
269-657
142-002CR
160-313
S27-254
269-656
269-1186
169-890
215-913
Lower Valve Body (1998 - 2000)
Lower Valve Body (2000 To Present)
Valve Seat
Rubber Diaphragm
Plastic Disk
Stainless Steel Disk
Spring
Divider Plate
O-Ring
Air Valve Body
Spring for Magnet
Magnet Assembly
Air Diaphragm
Diaphragm Spring
Valve Cover
Lockwasher
Screw
Timer Assembly
Cover – Timer Assy.
Fitting — Adj. "L"
Tube Connector
Air Valve Instruction Sheet
Valve Kit
S65-110
Repair Kit
S73-054C
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
49
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Metering Air Valve Troubleshooting Instructions
(Figure 13c)
How They Work
Refer to Figure 13c.
1. A pulse of air is created at the air diaphragm by pressing the pushbutton.
2. The pulse of air travels through the 1/8" air tubing into the lower port on the valve, up through
the magnet (housed within Item 9) and diaphragm, and exits through the top cover of the valve.
3. Releasing the pushbutton draws all the air out of the valve creating a vacuum inside the valve.
4. The top diaphragm acts as a check and does not let any air enter the valve through the top cover.
5. The vacuum created allows the magnet to drop down in the valve, attracting the armature plate.
6. The rising armature plate allows the water pressure to push the seat diaphragm off the valve
seat.
7. Water flows through the seat and out to the sprayhead.
8. Air is pulled into the valve through the timer by the vacuum on the inside of the valve.
9. The incoming air breaks the vacuum on the inside of the valve (Item 9).
10. The amount of air entering the valve through the timer determines the metering cycle.
11. When the vacuum is eliminated, the magnet spring pushes the magnet back to its original position.
12. The armature plate drops down to its original position, pushing the seat diaphragm back down
on the seat closing the valve.
13. A small amount of water passes through the diaphragm to equalize the pressure on either side of
the diaphragm.
Adjust Air Valve Meter Time
NOTE: The air valve timer is located next to the tube connector on the air valve body. The timer is
capped with a filter to prevent dirt build-up on the timer. The air valve timing can be adjusting from 5–60
seconds.
1. Remove filter cap and use a screwdriver to tighten or loosen the timer (Figure 13c). Turning the
timer clockwise increases the time; turning the timer counterclockwise decreases the time.
2. Continue to adjust until the timer is set at desired length.
3. Replace filter cap over the timer.
Tube Connection Leaks
1. Push in the white manual release button while pulling the tube out (see Figure 13c) to disconnect
the tube at the tube fitting. No tools are needed.
2. To correct a leak, press tubing firmly into the tube fitting and make sure it is seated.
3. If leak persists, remove tubing from the fitting, and trim the tubing end square with a razor-sharp
knife. If leak continues, replace the fitting or contact your Bradley representative for assistance.
50
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Bradley Showers
Metering Air Valve Troubleshooting Instructions
(Figure 13c) continued...
Metering Air Valve Troubleshooting
Problem: Water is dripping from the streamformers
Cause: Debris on valve seat or orifices
Step 1: Clean and inspect valve seat
1. Remove screws and disassemble metering valve.
2. Clean valve seat and inspect for deep gouges or scratches. Replace if necessary.
3. Remove all debris that may be clogging center hole of the plastic diaphragm assembly and offcenter hole in the rubber diaphragm.
Problem: Valve will not shut off
Cause: Timing mechanism is clogged
Step 1: Clean timing mechanism
1. Blow water and debris from perforated metal sleeve of timing mechanism if compressed air is
available.
2. Turn the adjusting screw in all the way but do not force screw.
3. Turn adjusting screw out to desired cycle time.
Problem: Valve will not turn on
Cause: Water is not being supplied to unit
Step 1: Open all stops on the valve assembly
Problem: Timing cannot be adjusted for more than five seconds
Cause: There is an air leak
Step 1: Check assembly
1. Check all tubing and fittings for proper assembly.
2. Tighten all screws which hold valve together.
Problem: Pushbutton does not work properly
Cause: Air volume may not be sufficient to operate valve
Step 1: Check all fittings for air leaks
Problem: Valve cycles properly, but water does not form streams and drip s from
streamformer
Cause: Flow control is clogged or is not seated properly
Step 1: Inspect and clean air flow control assembly
1. Remove 1/4" tubing and 1/4" tube connector fitting from metering air valve (Figure 13c).
2. Inspect flow control and remove debris that may be clogging assembly.
3. Replace fitting using Teflon™ tape on pipe threads.
4. Replace 1/4" tubing as follows: cut 1/4" from the end of the tube to make sure the end is square,
then insert into tube connector fitting.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
51
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Micro-Touch ™
Operation and Service Instructions
(Figure 14)
How Micro-Touch TM III works
See below.
1. Pushbutton sends electrical impulse (millivolts) to circuit board.
2. Circuit board controls metering style and timing sent to solenoid.
3. Solenoid receives signals from circuit board and open/closes water path-way to outlet.
Metering Mode Options
Meter Only:
One press of the activation button activates the cycle and the fixture will complete
its present cycle even if the button is pressed at subsequent times during the cycle.
Typical Application:
Standard operation for most applications and fixtures.
52
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Micro-Touch ™
Bradley Showers
(Figure 14 Continued)
Comby Mode:
Allows the flexibility of setting the timing functions of two stations
(solenoids) independently of the other four.
Typical Application:
Separate timing of two shower stations from timing of four others.Delay
Time: After a cycle is complete, a delay period can be set to prevent the initiation of a second
cycle for a preset length of time.
Typical Application:
For use in public areas where building owner does not want user to
immediately restart timing cycle. Typical uses include physical education
facilities and swimming pool areas.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
53
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Circuit Board Pushbuttons and LEDs
Operation and Service Instructions
(Figure 14 continued)
Pushbuttons
There are two pushbuttons on the circuit board—one labeled MODE, and one labeled SEC. The
MODE button is used to program the metering mode, and the SEC button is used to program the
cycle time for the mode in increments of 1 second. Also, the MODE and SEC buttons can be used
together to program the cycle time in increments of 15 seconds (see Program the Circuit Board on
following pages).
LEDs
• There are five LEDs on the circuit board—they are labeled DS1, DS2, DS3, DS4, and DS5 .
• LED DS5: When the MODE pushbutton is pressed, LED DS5 flashes repeatedly until the MODE
pushbutton is released. The number of times you allow LED DS5 to flash determines the metering
mode programmed (see Program the Circuit Board).
When the SEC pushbutton is pressed, LED DS5 flashes repeatedly until the SEC pushbutton is
released. When programming the cycle time for a metering mode, each flash of LED DS5 equals 1
second of cycle time.
• LEDs DS1, DS2, DS3, and DS4: Different combinations of these LEDs light, and remain lit, once
you have programmed a metering mode using the MODE pushbutton. The combination of lit LEDs
indicates the metering mode you have programmed (see Program the Circuit Board).
Figure 14a
54
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Program the Circuit Board
(Figure 14 Continued)
Factory preset cycle timing
The fixture cycle timing and metering option is preset at the factory. The preset for showers is the
Meter Only mode with a cycle time of 20 seconds. This option also includes a built-in delay from the
completion of the metered cycle of one second until the pushbutton can again be activated. If you
want to change the mode and/or cycle time, see the procedures for the desired mode on the following
pages.
Pressing the MODE and SEC pushbuttons
IMPORTANT: Sharp-tipped tools can puncture the waterproof seal that covers the
pushbuttons. Use only tools with blunt tip s to press the MODE and
SEC pushbuttons.
The MODE and SEC pushbuttons are accessed through a grommet on top of the circuit board housing (see Figure 14b below). To press a button, insert a blunt-tipped tool (i.e.: small screwdriver)
through the hole in the grommet.
Figure 14b
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
55
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Program the Circuit Board
(Figure 14 Continued)
Program Meter Only mode
Program mode:
1. Press MODE until LED DS5 flashes one time.
Result: LED DS2 should be lit to indicate that the circuit board is programmed for the Meter
Only mode.
Program cycle time (if different than factory-set time):
1. Press MODE until LED DS5 flashes four times.
Result: LED DS2 and DS3 should be lit to indicate that you are ready to enter the cycle time.
2. Enter the cycle time in 1-second or 15-second increments.
• 1-second increments: Press SEC until the number of times that LED DS5 flashes equals the number of seconds for the desired cycle time.
• 15-second increments: Remove the circuit board from its housing (see following pages for instructions). Press SEC and MODE at the same time—each flash of LED DS5 equals 15 seconds of cycle
time. Release SEC and MODE when the desired time has been entered.
Result: Only LED DS2 should be lit to indicate that the circuit board is programmed for the
Meter Only mode.
Program Double Touch mode
Program mode:
1. Press MODE until LED DS5 flashes two times.
Result: LED DS1 should be lit to indicate that the circuit board is programmed for the
Double Touch mode.
Program cycle time (if different than factory-set time):
1. Press MODE until LED DS5 flashes four times.
Result: LED DS1 and DS3 should be lit to indicate that you are ready to enter the cycle time.
2. Enter the cycle time in 1-second or 15-second increments.
• 1-second increments: Press SEC until the number of times that LED DS5 flashes equals the number of seconds for the desired cycle time.
• 15-second increments: Remove the circuit board from its housing (see following pages for instructions). Press SEC and MODE at the same time—each flash of LED DS5 equals 15 seconds of cycle
time. Release SEC and MODE when the desired time has been entered.
Result: Only LED DS1 should be lit to indicate that the circuit board is programmed for the
Double Touch mode.
Program Comby mode
Program mode:
1. Press MODE until LED DS5 flashes three times.
Result: LED DS1 and DS2 should be lit to indicate that the circuit board is programmed for
the Comby mode.
Program cycle time (if different than factory-set time):
1. To assign lavatory (long) time, press MODE until LED DS5 flashes four times.
Result: LED DS1, DS2, and DS3 should be lit to indicate that you are ready to enter the
lavatory (long) cycle time.
56
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Bradley Showers
Program the Circuit Board
•
•
•
•
(Figure 14 Continued)
2. Enter the lavatory (long) cycle time in 1-second or 15-second increments.
1-second increments: Press SEC until the number of times that LED DS5 flashes equals the number of seconds for the desired cycle time.
15-second increments: Remove the circuit board from its housing (see following pages for instructions) press SEC and MODE at the same time—each flash of LED DS5 equals 15 seconds of cycle
time. Release SEC and MODE when the desired time has been entered.
Result: LEDs DS1 and DS2 should be lit to indicate that the circuit board is programmed for
the Comby mode.
3. To assign flush (short) cycle time, press MODE until LED DS5 flashes five times.
Result: LED DS1, DS2, and DS4 should be lit to indicate that you are ready to enter the
lavatory (long) cycle time.
4. Enter the flush (short) cycle time in 1-second or 15-second increments.
1-second increments: Press SEC until the number of times that LED DS5 flashes equals the number of seconds for the desired cycle time.
15-second increments: Remove the circuit board from its housing (see following pages for instructions) press SEC and MODE at the same time—each flash of LED DS5 equals 15 seconds of cycle
time. Release SEC and MODE when the desired time has been entered.
Result: LEDs DS1 and DS2 should be lit to indicate that the circuit board is programmed for
the Comby mode.
Program Delay Time
1. Press MODE until LED DS5 flashes six times.
Result: No new LEDs are lit, and you are ready to enter the Delay Time.
2. Enter the flush (short) cycle time in 1-second or 15-second increments.
• 1-second increments: Press SEC until the number of times that LED DS5 flashes equals the number of seconds for the desired Delay Time.
• 15-second increments: Remove the circuit board from its housing (see next page for instructions)
press SEC and MODE at the same time—each flash of LED DS5 equals 15 seconds of cycle time.
Release SEC and MODE when the desired time has been entered.
Result: The Delay Time has been programmed.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
57
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Program the Circuit Board
Operation and Service Instructions
(Figure 14 Continued)
Remove circuit board from housing
NOTE:
Follow the procedure below only when you want to access the SEC
and MODE pushbuttons to program cycle times in increment s of 15
seconds.
1. Remove the pan head screw that secures the access panel to the housing (see Figure below).
IMPORTANT: Do not allow the circuit board to come in cont act with metal surfaces.
Since power is still being supplied to the circuit board, cont act with
metal surfaces can cause the board to short-circuit.
2. Pull the circuit board from the housing to access the MODE and SEC pushbuttons.
Figure 14c
58
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Circuit Board Pushbuttons and LEDs
Bradley Showers
(Figure 14 continued)
Bradlink™Option Description
Bradley offers a unique communications link as standard equipment. The Bradlink™ feature (when
specified) will allow all fixtures utilizing the Micro-Touch™ system to transfer timing information
from one circuit board to another. With two conductor, 22 AWG, twisted pair wire, multiple fixtures
can be "Bradlinked" together. For example, if a facility has a room with 10 fixtures, a maintenance
person can go to any one of the fixtures, set the metering time, and the entire room would be automatically reset to the "new" information. There is no need to time each valve or fixture individually.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
59
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Pressure Balancing Mixing Valve S27-022
(Figure 15)
For Column Showers
15
10
19
16
11
17
20
13
5
8
6
NOTE:
Can be replaced with Bradley
Equa-Flo S65-075 (2-5 Person)
S65-076 (6 Person)
H
1
C
MANIFOLD
NOTE:
Does not include escuthcheon
and screws.
COLUMN
3
7
2
9
4
12
14 18
Parts List
Column Valve
Assembly
S27-022
60
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14
15
16
17
18
19
20
169-264
169-265
169-258
169-267
169-274
169-266
169-257
S27-092
169-263
169-259
169-262
160-177
169-268
150-032
150-034
S27-067
169-269
169-260
169-255
169-261
169-270
Handle
Handle Set Screw
Packing Nut
Lock Nut
Dial
Packing
Cap
Limit Stop Assembly
Dome Cover
Cold Washer Retainer
Cold Washer
Escutcheon Screw
Cap Gasket
Escutcheon, 2-5 Person Column
Escutcheon, 6 Person Column
Flow Control Spindle
Top Seat Gasket
Hot Washer
Body Seat
Hot Washer Screw
Bottom Seat Gasket
Gasket
Kit
S65-013
Qty
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Pressure Balancing Mixing Valve S27-022
Bradley Showers
(Figure 15)
Service Suggestions:
1. Open valve to about warm position.
2. Loosen handle screw and remove handle.
3. Remove escutcheon.
4. Unscrew dial lock nut and remove dome cover.
5. Unscrew Valve Cap with complete assembly.
6. Leave Packing Nut in place while unscrewing cap to avoid distorting end of cap.
7. When cap is unscrewed, entire working unit may be removed.
The perforated cylinder is an integral part of Flow Control Spindle and does not unscrew. The cylinder is hollow and contains a piston. The piston is free-moving and provides pressure-balancing features of valve. By sliding back and forth under any variation of pressure. Piston opens or throttles
Hot and Cold Water ports to control proper delivery ratio of each, and so maintains constant even
temperature. Control action is entirely automatic, the Piston is sealed into cylinder, neither Cylinder
nor Piston should be tampered with. Under no circumstances should wrench or pliers be used on
Cylinder. It is a carefully machined unit and any marking or gouging will destroy it's function.
The Piston should be free inside Cylinder at all times and should click back and forth when assembly is shaken. After long service in "rugged" waters, it is possible that mineral or other deposits may
block the Piston's action. Normally, tapping Handle End of Spindle against a solid object will free
the piston. If it is so solidly plugged that this is not effective, replace entire Spindle Assembly.
Ordinary service requires only replacement of Hot and Cold Washers. To replace Cold Washer,
remove large knurled Washer Retainer. To replace Hot Washer, remove Washer Screw. It is essential
that both Hot and Cold Washers be replaced at the same time, even if only one appears to require
attention. Washer and Gasket Kit should be used for this service. Use only Pressure Balancing Valve
Washers.
In extreme cases or after long years of service, Body Seat may require replacement. Body Seat is
removable after removal of four mounting screws.
NOTE: When reassembling valve after any repairs, be sure Cylinder is drawn close to Cap before
screwing Cap back into position.
Valves are equipped with "LIMIT STOP". This Stop, located below Dome Cover, can be used to
limit temperature of tempered water discharge.
TO ADJUST:
1. Open valve and turn handle to maximum desired discharge temperature.
2. Unscrew LIMIT STOP Cap.
3. Screw in adjusting set screw until it seats.
4. While still holding valve open to desired position, replace LIMIT STOP Cap and tighten securely
against its gasket.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
61
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Pressure Balancing Mixing Valve S27-025
(Figure 16)
For Panelon and Wall Showers
7
6
8
4
1
2
1
9
12
14
11 13
5
15
3
17
NOTE:
Includes escuthcheon and
screws.
10
16
Parts List
Column Valve
Assembly
S27-025
62
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
169-408
169-409
169-261
169-260
169-404
169-262
169-259
169-402
169-401
S27-092
169-266
S27-091
169-399
169-398
169-397
169-265
169-264
Top & Bottom Seat Gasket
Renewable Seat
Hot Washer Screw
Hot Washer
Flow Control Spindle
Cold Washer
Cold Washer Retainer
Cap Gasket
Cap
Limit Stop Assembly
Packing
Escutcheon and Screw
Packing Nut
Dome Cover
Dome Lock Nut
Handle Screw
Handle
Gasket
Kit
S65-048
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Pressure Balancing Mixing Valve S27-025
Bradley Showers
(Figure 16)
Service Suggestions:
1. Open valve to about warm position.
2. Loosen handle screw and remove handle.
3. Remove escutcheon.
4. Unscrew dial lock nut and remove dome cover.
5. Unscrew Valve Cap with complete assembly.
6. Leave Packing Nut in place while unscrewing Cap to avoid distorting end of Cap.
7. When Cap is unscrewed, entire working unit may be removed.
The perforated cylinder is an integral part of Flow Control Spindle and does not unscrew. The
cylinder is hollow and contains a piston. The piston is free-moving and provides pressure-balancing
feature of valve. By sliding back and forth under any variation of pressure, Piston opens or throttles
Hot and Cold Water ports to control proper delivery ratio of each, and so maintains constant even
temperature. Control action is entirely automatic, the Piston is sealed into cylinder, neither Cylinder
nor Piston should be tampered with. Under no circumstances should wrench or pliers be used on
Cylinder. It is a carefully machined unit and any marking or gouging will destroy it's function.
The Piston should be free inside Cylinder at all times and should click back and forth when assembly is shaken. After long service in "rugged" waters, it is possible that mineral or other deposits may
block the Piston's action. Normally, tapping Handle End of Spindle against a solid object will free
the piston. If it is so solidly plugged that this is not effective, replace entire Spindle Assembly.
Ordinary service requires only replacement of Hot and Cold Washers. To replace Cold Washer,
remove large knurled Washer Retainer. To replace Hot Washer, remove Washer Screw. It is essential
that both Hot and Cold Washers be replaced at the same time, even if only one appears to require
attention. Washer and Gasket Kit should be used for this service. Use only Pressure Balancing Valve
Washers.
In extreme cases or after long years of service, Body Seat may require replacement. Body Seat is
removable after removal of four mounting screws.
NOTE: When reassembling valve after any repairs, be sure Cylinder is drawn close to Cap before
screwing Cap back into position.
Valves are equipped with "LIMIT STOP". This Stop, located below Dome Cover, can be used to
limit temperature of tempered water discharge.
TO ADJUST:
1. Open valve and turn handle to maximum desired discharge temperature.
2. Unscrew LIMIT STOP Cap.
3. Screw in adjusting set screw until it seats.
4. While still holding valve open to desired position, replace LIMIT STOP Cap and tighten securely
against its gasket.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
63
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Presto Valves & Cartridges
Operation and Service Instructions
(Figure 17)
Tailpiece Nut
(110-005)
Fiber Washer
(Suppied with Valve)
Presto 50B Valve
for 1C and Wall Showers
(269-161)
Locking Collar
Assembly
(S30-082)
3/8" NPT
Tailpiece
(129-009)
or
1/2" Nominal Copper
Sweat Solder
Connection
Tailpiece (129-057)
Filter on Inlet Side
(Supplied with Valve)
Repair Cartridge for
Presto 50B Valve
in 1C and Wall Showers
(269-1577)
PRESTO 50B VALVE
FOR 1C AND WALL
SHOWERS
Set Screw
Tailpiece Nut
(110-005)
Fiber Washer
(124-001AF)
3/8" NPT
Tailpiece
(129-009)
or
1/2" Nominal Copper
Sweat Solder
Connection
Tailpiece (129-057)
Presto 50B Valve
For Columns
S27-239
Repair Cartridge for
Presto 50B Valve
in Column Showers
(269-1578)
PRESTO 50B VALVE
FOR COLUMN
SHOWERS
Tailpiece Nut
(110-005)
Fiber Washer
(Suppied with Valve)
Presto
Alpha 80
Valve
(269-160)
64
3/8" NPT
Tailpiece
(129-009)
or
1/2" Nominal Copper
Sweat Solder
Connection
Tailpiece (129-057)
Filters on Inlet Sides
(Supplied with Valve)
Repair Cartridge for
Presto Alpha 80 Valve
(269-1800)
PRESTO ALPA 80 VALVE
. 800-875-7952
FOR MORE INFORMATION OR TO PLACE A ORDER CALL
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Pushbutton Air Valve Repair Parts
(Figure 18)
9
10
11
8
12
13
14
6
7
5
4
3
1
2
Parts List
Pushbutton
Assembly
S45-1712
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
110-115
140-743
159-400
204-501
S08-324
169-890
269-1186
118-279
160-165
135-065
119-227
125-099
130-023
S45-125
Hex Nut 1/2 NPSM
Actuator Bracket
Mounting Plate
Decal — Air Valve
Pushbutton Ass'y.
1/8 Tube Connector
Fitting — Adj. "L"
Molded Actuator Body
Screw
Spring
Molded Piston
U-Cup
Wrench
Lubricant
Repair
Kit
S65-223
Qty
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
NOTE: Lubricate "U" cup (Item 12) on plunger with lubricant (S45-125). Apply thin coat all around I.D. - 1" deep.
Do not use spray silicone or petroleum based lubricant s on components.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
65
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Pushbutton Air Valve Repair Parts
(Figure 19)
8
9
10
7
11
12
13
6
5
4
2
1
3
Parts List
Pushbutton
Assembly
S45-1713
Item
Part No.
Description
1
2
3
4
5
6
7
8
9
10
11
12
110-115
140-743
159-400
204-501A
S08-324
169-890
118-279
160-165
135-065
119-227
125-099
130-023
S45-125
Hex Nut 1/2 NPSM
Actuator Bracket
Mounting Plate
Decal — Air Valve
Pushbutton Ass'y.
1/8 Tube Connector
Molded Actuator Body
Screw
Spring
Molded Piston
U-Cup
Wrench
Lubricant
Repair
Kit
S65-224
Qty
1
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
NOTE: Lubricate "U" cup (Item 11) on plunger with lubricant (S45-125). Apply thin coat all around I.D. - 1" deep.
Do not use spray silicone or petroleum based lubricant s on components.
66
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Pushbutton Air Valve Repair Parts For Column Showers
(Figure 32)
9
12
13
10
8
7
11
14
6
5
3
1
2
Parts List
Pushbutton
Assembly
S45-1934A
2-5 Person
Item
Part No.
1
2
3
3
4
5
6
7
8
9
10
11
12
13
110-115
140-743
150-174
150-177
204-522
S08-324
269-1186
169-890
118-279
160-165
135-065
119-227
125-099
130-023
S45-125
Description
Hex Nut 1/2 NPSM
Actuator Bracket
Escutcheon
Escutcheon
Nameplate
Pushbutton Ass'y.
Fitting – Adj “L”
1/8 Tube Connector
Molded Actuator Body
Screw
Spring
Molded Piston
U-Cup
Wrench
Lubricant
Pushbutton
Assembly
S45-1934B
6 Person
Repair
Kit
S65-223
Qty
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
1
1
1
1
NOTE: Lubricate "U" cup (Item 11) on plunger with lubricant (S45-125). Apply thin coat all around I.D. - 1" deep.
Do not use spray silicone or petroleum based lubricant s on components.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
67
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
WS-1X Showerheads
Operation and Service Instructions
(Figure 20)
* Add suffix G for 1.5 GPM Flow Restrictor
(Example: S24-173G)
154-139 Arm
110-015 Nut
269-1679 Head
WS-1X Basic Showerhead S24-172
154-139 Arm
110-015 Nut
153-117 Adaptor
S24-008 Head
Standard Institutional Showerhead S24-173 *
154-139 Arm
110-015 Nut
153-117 Adaptor
S54-002 LBJ
S24-008 Head
Standard Institutional Showerhead
with Lockable Ball Joint S24-174 *
68
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Showerheads
Bradley Showers
(Figure 21)
1WCA, Econowall (2W and 3W), 1F, 1K and Panelons
154-126
Showerhead Arm
Shower Panel
160-111
Screw
142-002CF
Washer
160-111
Screw
9/16"-18 UNF
Thread
3/8"-18 NPT
Thread
153-320
Adapter
153-321
Adapter
9/16"-18 UNF
Thread
1/2"-14 NPT
Thread
Deluxe Showerheads
Standard Institutional Showerheads
1/2"-14 NPT
3/8"-18 NPT
Standard Showerhead S24-008 *
Ball Joint S24-093
Showerhead w/ Arm S24-077
Lockable Ball Joint S24-095
Showerhead w/ Arm S24-077M
Showerhead w/ Arm S24-038 *
3/8"-18 NPT
1/2"-14 NPT
S24-008
S02-058
Allen Key Volume Control S24-111 *
Showerhead w/ Arm S24-040 *
3/8"-18 NPT
S24-008
SX Showerhead
S24-161 *
Showerhead w/ Arm S24-086 *
Fixed direction
spray pattern
is adjustable
only through
orifice with 1/8"
Allen Key
Allen Key Volume Control Ball Joint S24-099
Showerhead w/ Arm S24-159
Allen Key Volume Control Lockable Ball Joint S24-101
Showerhead w/ Arm S24-160
S02-057
Lever Handle Volume Control S24-112 *
Showerhead w/ Arm S24-039 *
1/2"-14 NPT
3/8"-18 NPT
S24-008
S54-002
Lockable Ball Joint Assembly S24-108 *
Showerhead w/ Arm S24-116 *
Lever Handle Volume Control Ball Joint S24-096
Showerhead w/ Arm S24-077D
Lever Handle Volume Control Lockable Ball Joint S24-098
Showerhead w/ Arm S24-163
1/2"-14 NPT
3/8"-18 NPT
S24-008
S54-002
S02-058
Economy Soft Flow With Ball Joint 269-919
Showerhead w/ Arm S24-162
Lockable Ball Joint Assembly With Allen Key Volume Control S24-109 *
Showerhead w/ Arm S24-118 *
3/8"-18 NPT
* Add suffix G for 1.5 GPM Flow Restrictor
(Example: S24-038G)
S54-002
S24-008
S02-057
Lockable Ball Joint Assembly With Lever Handle Volume Control S24-110 *
Showerhead w/ Arm S24-120 *
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
69
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Compression Valve With Lever Handle – Hot, Cold or Tempered
For Individual, Econo-Walls, Wall Savers, Panelons and Column Showers
2
1
3
4
5
6
7
9
8
10
13
12
11
119-052
Valve Stem
Note:
153-257
Adaptor
(Assembled with loctite)
These two parts
replaced by Item 8
(Part 119-244) in
December, 2002
Figure 2A
Parts List
Assembly
S02-031C
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
Part No.
160-225
153-163
128-050
121-012
125-001BC
124-001BD
142-002BF
119-244
120-017
125-001L
160-245
124-001K
117-002
Description
Screw
Insert
Handle
Bonnet
O-Ring
Fiber Washer
Brass Washer
Valve Stem - Single Lever
Valve Stem Extension
Bibb Washer
Screw
Fiber Washer for Valve Body
Valve Seat-H & C
NOTE: It is not recommended that the component of
the stem assemblies be ordered individually. It is likely
that valve stem extension can not be removed without
breaking as it is made of Celcon plastic. If breakage
occurs, that portion of the plastic remaining in valve stem
no. 119-244 will have to be drilled out. It is our
recommendation that valve stem assembly no. S21-070
always be replaced complete.
70
Valve Stem
Assembly
S21-070
Valve Stem
Extension
S21-021
Repair Parts
Kit
S45-048A
Qty
1
1
1
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
1
1
1
1
—
—
—
—
—
—
—
—
—
—
1
1
1
—
—
—
—
—
—
1
1
—
—
1
1
1
1
1
Used in Conjunction With the Following Existing
Parts:
118-009
Valve Body
150-004
Escutcheon, Columns
150-035
Escutcheon, Wall Savers, Panelons
* Use 3/8" Allen Wrench to remove valve seat
NOTE: Older style columns may require a special
bushing for the seat: 153-126
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Compression Valve With Lever Handle – Hot, Cold or T empered
How they Work: Refer to Figure 2A.
Counter-clockwise rotation of the handle and valve stem causes the bibb washer to move away from the
valve seat allowing water to flow through the valve seat.
Troubleshooting
PROBLEM
Water drips from shower
head.
CAUSE
SOLUTION
Worn bibb washer
Replace bibb washer
Mineral or foreign material
build up on valve seat.
Clean or replace valve seat
Water drips from handle or
bonnet.
O-Ring worn or bonnet
insufficiently tightened.
Replace O-Ring or tighten
bonnet.
Water will not shut off.
Bibb washer retaining screw
worked loose resulting in
washer not seating properly.
Tighten or replace washer
retaining screw.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
71
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Compression Valve, Current Style – Hot, Cold or Tempered
For Individual, Econo-Walls, Wall Savers, Panelons and Column Showers
1
3
2
4
5
6
7
9
8
10
11
12
13
14
Figure 2B
Parts List
Assembly
S02-031
Item
Part No.
Description
1
2
2
2
3
4
5
6
7
8
9
10
11
12
13
*14
160-145
142-027
142-027A
142-027B
142-002BL
128-028
121-012
125-001BC
124-001BD
142-002BF
119-052
120-017
125-001L
160-245
124-001K
117-002
Screw
Index Washer (White)
Index Washer (Blue)
Index Washer (Red)
Insert Washer
Handle
Bonnet
O-Ring
Fiber Washer
Brass Washer
Valve Stem
Valve Stem Extension
Bibb Washer
Screw
Fiber Washer for Valve body
Valve Seat-H & C
Valve Stem
Assembly
S21-020
Valve Stem
Extension
S21-021
Repair Parts
Kit
S45-048A
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
1
1
1
—
—
—
—
—
—
—
—
—
1
1
—
—
1
1
1
1
1
NOTE: It is not recommended that the component of the stem assemblies be ordered individually . It is likely that
valve stem extension can not be removed without breaking as it is made of Celcon plastic. If breakage occurs, that
portion of the plastic remaining in valve stem no. 1 19-052 will have to be drilled out. It is our recommendation that
valve stem assembly no. S21-020 always be replaced complete.
S02-031 Complete valve stem and handle assembly with
Used in Conjunction With the Following Existing Parts:
White Index Washer (Tempered).
118-009
Valve Body
150-004
Escutcheon, Columns
S02-031A Complete valve stem and handle assembly with
150-035
Escutcheon, Wall Savers, Panelons
Blue Index Washer (Cold).
S02-031B Complete valve stem and handle assembly with
* Use 3/8" Allen Wrench to remove valve seat
Red Index Washer (Hot)
NOTE: Older style columns may require a special
bushing for the seat:
72
153-126
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Compression Valve, Current Style – Hot, Cold or Tempered
How they Work: Refer to Figure 2B.
Counter-clockwise rotation of the handle and valve stem causes the bibb washer to move away from the
valve seat allowing water to flow through the valve seat.
PROBLEM
Water drips from shower
head.
Troubleshooting
CAUSE
SOLUTION
Worn bibb washer
Replace bibb washer
Mineral or foreign material
build up on valve seat.
Clean or replace valve seat
Water drips from handle or
bonnet.
O-Ring worn or bonnet
insufficiently tightened.
Replace O-Ring or tighten
bonnet.
Water will not shut off.
Bibb washer retaining screw
worked loose resulting in
washer not seating properly.
Tighten or replace washer
retaining screw.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
73
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
1C Single Compression Valve with Lever Handle
For Built-in, Concealed Supply Application
1
1/2" NPT
outlets
(Ref)
2
4
7
8
9
10
6
3
12
13
11
1/2" NPT
inlet (Ref)
5
Figure 2C
14
Turn in Item 5,
valve stem all the way,
back off 1 to 2 turns,
tighten Item 7, bonnet
holding stem in place.
Parts List
Assembly
S67-507
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Part No.
Description
118-146A
117-034
113-430
150-110
119-244
S21-021
121-019
125-001BC
124-001BD
142-002BF
153-163
160-225
128-050
169-168
Mix Chamber
Valve Seat
Escutcheon Sleeve H & C
Escutcheon
Valve Stem - Lever Handle
Valve Stem Ext Comp
Bonnet
O-Ring .818" OD
Flat Washer .641 x .938 x .063
Flat Washer .641 x .813 x .063
Diverter Valve Insert
Screw 10-24 x 3/4 FL
Handle
Pipe Plug - 1/2" Brass
Valve Stem Assembly
S21-070
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
—
—
—
—
1
1
—
—
—
—
—
—
—
—
NOTE: It is not recommended that the component of the stem assemblies be ordered individually . It is likely that
valve stem extension can not be removed without breaking as it is made of Celcon plastic. If breakage occurs, that
portion of the plastic remaining in valve stem no. 1 19-244 will have to be drilled out. It is our recommendation that
valve stem assembly no. S21-070 always be replaced complete.
74
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
1C Single Compression Valve with Lever Handle
How they Work: Refer to Figure 2C.
Counter-clockwise rotation of the handle and valve stem causes the bibb washer to move away from the
valve seat allowing water to flow through the valve seat.
Troubleshooting
PROBLEM
Water drips from shower
head.
CAUSE
SOLUTION
Worn bibb washer
Replace bibb washer
Mineral or foreign material
build up on valve seat.
Clean or replace valve seat
Water drips from handle or
bonnet.
O-Ring worn or bonnet
insufficiently tightened.
Replace O-Ring or tighten
bonnet.
Water will not shut off.
Bibb washer retaining screw
worked loose resulting in
washer not seating properly.
Tighten or replace washer
retaining screw.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
75
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
1C Single Compression Valve
For Built-in, Concealed Supply Application
1
1/2" NPT
outlets
(Ref)
2
7
8
9
10
6
4
13
12
11
14
15
1/2" NPT
inlet (Ref)
5
3
Figure 2D
Turn in Item 5,
valve stem all the way,
back off 1 to 2 turns,
tighten Item 7, bonnet
holding stem in place.
Parts List
Assembly
S67-379
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Part No.
Description
118-146A
117-034
113-430
150-110
119-052
S21-021
121-019
125-001BC
124-001BD
142-002BF
142-002BL
160-145
142-027
128-057
169-168
Mix Chamber
Valve Seat
Escutcheon Sleeve H & C
Escutcheon
Valve Stem - H & C
Valve Stem Ext Comp
Bonnet
O-Ring .818" OD
Flat Washer .641 x .938 x .063
Flat Washer .641 x .813 x .063
Washer .391 x .625 x .078
Screw 1/4-28 x 1/2 FL
Washer - Index - White
Handle - Polished
Pipe Plug - 1/2" Brass
Valve Stem Assembly
S21-020
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
—
—
—
—
1
1
—
—
—
—
—
—
—
—
—
NOTE: It is not recommended that the component of the stem assemblies be ordered individually . It is likely that
valve stem extension can not be removed without breaking as it is made of Celcon plastic. If breakage occurs, that
portion of the plastic remaining in valve stem no. 1 19-052 will have to be drilled out. It is our recommendation that
valve stem assembly no. S21-020 always be replaced complete.
76
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
1C Single Compression Valve
How they Work: Refer to Figure 2D.
Counter-clockwise rotation of the handle and valve stem causes the bibb washer to move away from the
valve seat allowing water to flow through the valve seat.
Troubleshooting
PROBLEM
Water drips from shower
head.
CAUSE
SOLUTION
Worn bibb washer
Replace bibb washer
Mineral or foreign material
build up on valve seat.
Clean or replace valve seat
Water drips from handle or
bonnet.
O-Ring worn or bonnet
insufficiently tightened.
Replace O-Ring or tighten
bonnet.
Water will not shut off.
Bibb washer retaining screw
worked loose resulting in
washer not seating properly.
Tighten or replace washer
retaining screw.
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
77
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Solenoid Valves
Operation and Service Instructions
(Figure 24)
Coverall and Column Solenoid Valves
S07-050 Muller Valve Assembly
4
(Figure 24a)
Repair
Kit
S65-123
3
Item
1
2
3
4
2
1
Description
Qty
Membrane
Membrane Pressure Spring
Plunger
Pressure Spring (Plunger)
1
1
1
1
Figure 24a
All Other Shower Solenoid Valves
269-719 Eaton Valve Assembly
(Figure 24b)
Repair
Kit
S65-113
3
2
1
Item
Part No.
Description
Qty
1
2
3
269-983
269-577
269-578
Diaphragm
Armature
Spring
1
1
1
Figure 24b
78
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Touch 'N Flo Shower Valve, Current Version
(Figure 25)
For Individual, Econo-Walls, Wall Savers, Panelons and Column Showers
22
2
3
4
5
7
8
11
14
16
19
17
20
6
9
10
12
13
18
15
1
21
Figure 25
* Note:
Item #10 includes 125-001BF O-Ring
Item #12 includes 125-001EF O-Ring
Item #18 includes 125-049 Cup W asher
May consider plunger assembly S64-087 if extreme low water pressure condition exist s.
NOTE: Lubricate "U" cup (Item 17) on plunger with Parker "O" Lube (S45-125). Apply thin coat all around I.D. - 1"
deep. Do not use spray silicone or petroleum based lubricant s on components.
Escutcheon & Screws (Not Shown) must be ordered sep arately as follows:
150-033
150-031
160-165
Escutcheon 6-Person Column Shower
Escutcheon 2-5 Person Column Shower
Escutcheon Screw — 1 required
150-077
160-255
Escutcheon for all other Showers
Escutcheon Screw — 2 required
159-107
160-290
Wall Plate for Individual Shower
Wall Plate Screw — 2 required
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
79
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Touch 'N Flo Shower Valve Parts List, Current Version
Assembly
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Part No.
Description
128-048
107-243
107-253
182-065
S21-032
135-034
S88-039
S88-039B
125-001BF
S68-005*
118-210
S64-034*
125-001EF
169-250
135-028
173-012
125-078
S64-088
118-121
117-030
S27-070
S27-180*
S45-125
215-717
Push Button
Cover 1-5/8" Long
Cover (Indiv. only) 2-3/4" Long
Spacer (Indiv. only)
Screw Ass'y
Spring
Standard Fixed Orifice Ass'y
Longer Cycle Orifice Ass'y
O-Ring
Guide
Body
Poppet Ass'y
O-Ring
Gasket
Conical Spring
Filter
U-Cup (Viton, Brown)
Plunger Ass'y
Bottom Body
Seat (Assemble with Teflon Dope)
Internal Stop Core
Bottom Body Ass'y
Parker "O" Lube
Instruction Sheet
Complete
Valve
Kit ➊
S45-320
Body
Ass'y
Kit
S73-019S
(Figure 25)
Repair
Kit
S65-071
Repair
Kit
S65-070
—
—
—
—
1➋
—
1➋
—
—
1➋
1➋
1
—
—
1
1➋
—
1
—
—
—
—
—
—
—
1
—
—
—
—
—
1
1
1
1
—
1
—
—
—
1
—
—
—
1
—
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
—
1
—
1
1
—
—
1➋
1
1➋
—
—
1➋
1➋
1
—
—
1
1➋
—
1
—
—
—
—
—
—
1➋
—
1➋
—
—
1➋
1➋
1
—
—
—
1➋
—
—
—
1
—
1
—
—
—
NOTE: Lubricate "U" cup (Item 17) on plunger with Parker "O" Lube (S45-125). Apply thin coat all around I.D. - 1"
deep. Do not use spray silicone or petroleum based lubricant s on components.
NOTE: ➊ Repair kit S45-320 applies to the "Short Cover" valve version only .
➋ These components part of assembly S73-046.
80
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Touch 'N Flo Shower Valve, Current Version
Bradley Showers
(Figure 25)
For Individual, Econo-Walls, Wall Savers, Panelons and Column Showers
Note:Refer to Illustration and parts list on previous pages.
Valve Timing
Note:Current style valve is supplied with Fixed Orifice Timing Assembly. There is no need to adjust this
valve for timing. If previous version style of adjustable orifice is desired, parts are available.
Consult factory.
Current valve furnished from March of 1988 is equipped with fixed timing orifice assembly (S88039). This will time the valve to approximately 25 to 45 seconds. If a shorter cycle is desired, use
S88-039A, or if longer cycle is desired, use S88-039C. If servicing previous version of valve with
adjustable timing orifice, follow instructions below. It would be desirable, however, to replace both
orifice and O-Ring in valve body with Fixed Orifice Assembly.
1. Remove escutcheon.
2. Remove cover (Items 2 or 3).
Note:The pushbutton, and spring will also come loose with the cover.
3. Check present timing by depressing poppet (Item 12). Measure the time from poppet release to
valve shutoff.
4. Changing timing:
A. Insert 3/32"Allen Key into screw (Item 5).
B. Turn clockwise to lengthen time valve is open.
C. Turn counterclockwise to shorten time valve is open.
D. Recheck timing by as indicated in Step 3, continuing adjustment until desired timing is
reached.
Note:A short turn will change timing considerably when setting valve in excess of 45 seconds.
5. Replace cover and related parts.
6. Retest timing by depressing push button (Item 1). If timing is significantly different than in Step
4D, repeat Step 2 or follow note above referring to Fixed Orifice Assembly.
If Valve Will Not Shut Off
1. Remove escutcheon.
2. Remove cover (Items 2 or 3).
Note:The pushbutton, and spring will also come loose with the cover.
3. Using a 3/32" Allen Key, turn adjusting screw (Item 5) counterclockwise until adjusting screw is
flush with body (Item 11). If valve continues to run, proceed with the next step.
4. Turn integral stop (Item 21) to shut off water, remove body assembly (Item 11) and check for:
A. A loose or worn valve seat (Item 20).
B. Any obstruction between seat and plunger assembly.
C. Loose, missing or plugged filter (Item 16), in body assembly. If either condition exists, replace
entire body assembly (S73-019S).
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
81
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Touch 'N Flo Valve Service Procedures
Operation and Service Instructions
(Figure 25)... (Continued)
D. Missing plunger assembly (Item 18). Conical washer worn on not centered on plunger assembly. Replace if either condition exists.
E. Reassemble valve body assembly S73-019S and turn water on.
F. If valve still continues to run, proceed with Step 5.
5. Shut off water to shower, remove integral stop (Item 21), and check if bibb washer and screw
have become disassembled and have remained in passageway or if any other foreign matter may
be obstructing water flow. If integral stop core is defective, replace with a new unit, reassemble
and test.
If Valve Will Not Turn On
1. Check if all stops are open.
2. Integral stop washer may have slipped off retaining screw, allowing it to obstruct passageway.
Remove washer and replace integral stop (Item 21) with new unit.
3. Poppet guide (Item 10) may be screwed into body (Item 11) too tightly, this applies to older versions only. On current style, seal is made from poppet guide O-Ring 125-001BF to body, and
poppet assembly to guide with 125-001DB O-Ring integral to poppet.
4. Conical piston spring (Item 15) may be in upside down. Narrow end of spring should engage the
piston.
If Valve Timing is Unstable at Cycles In Excess of One Minute
1. Make certain to depress pushbutton (Item1) and hold for one second to test cycle.
2. Listen to shower for evidence of strong flowing fluctuations. If these exist when other showerheads are used, check building supply stops for full open, check if strainers are clean and tempering valves are on.
3. If timing drifts steadily longer or shorter, check to see what style of orifice is used (see note on
previous page regarding type of orifice utilized). If adjustable orifice is used, it is advisable to
select a fixed orifice assembly. If using a fixed orifice, remove and hold up to light to see if
passageway is clear for small amount of water to pass. Replace in cavity with O-Ring side first.
82
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
TouchTime®
Item
Part No.
(Figure 26)
Description
Qty
1
110-115
Nut
1
2
S83-128
Switch Assembly - 60 Second
1
2
S83-128F
Switch Assembly - 180 Second
3
159-354
Escutcheon
1
4
204-465
Decal (on face of escutcheon)
1
2
3
1
4
Figure 26a
Wiring Diagram
Connect volt meter leads,
one to each side of the
terminal block, as shown.
WHITE/GRAY WIRES
(60 SECOND)
BLUE/GRAY WIRES
(180 SECOND)
TOUCHTIME®
SWITCH
Figure 26b
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
83
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Servicing TouchTime® Push Button Unit
Operation and Service Instructions
(Figure 26)
If the TouchTime® push button unit does not function properly
1. Make sure the water supply and the 24 VAC power are both turned on.
If the water supply and the electrical power are both turned on but the push button is still not
functioning, check the wiring following the steps outlined in procedure #2 below.
2. Check the wiring following the procedure outlined below:
a. Turn the electrical power off.
b. Check the wiring for loose connections or corrosion and correct if necessary.
c. Turn the electrical power back on and retest the push button.
If, after checking the wiring, the push button is still not functioning properly, test the transformer
following the steps outlined in procedure #3.
3. Test the transformer with a volt meter following the procedure outlined below:
a. Turn the water supply off (the electrical power should remain on).
b. Set the volt meter scale to be able to read “24 VAC”.
c. Connect the volt meter leads to the terminal block (one on each side) as shown in Figure 26.
d. The voltage reading should indicate 24 VAC ± 10%.
If you are unable to obtain a proper voltage reading, the transformer is not working properly and
needs to be replaced. Contact your Bradley representative to order a replacement transformer (ask
for Bradley part number 269-703A).
If the transformer is working properly, turn the water supply back on and test the solenoid following the steps outlined in procedure #4.
4. Test the solenoid valve following the procedure outlined below:
a. Disconnect the White/Gray wires (60 second) or Blue/Gray wires (180 second) from the
solenoid.
b. Disconnect the brown power cord leads from the terminal block.
c. Connect the brown power cord leads directly to the solenoid. The solenoid coil should activate and you should hear a single click and a humming noise.
If the solenoid coil does not activate, the solenoid valve is not working properly and needs to be
replaced. Contact your Bradley representative to order a replacement solenoid valve assembly
(ask for Bradley part number S07-053).
If, after checking the transformer, the solenoid valve and the wiring, you are unable to activate
the shower sprayhead by pressing the TouchTime® push button, the TouchTime® switch assembly
is not working properly and needs to be replaced. Contact your Bradley representative to order a
replacement switch assembly (ask for Bradley part number S83-139).
84
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Touch Time™ with Battery Operation
1.
2.
3.
4.
5.
(Figure 33)
Insert one CRP2 6-volt lithium battery into each battery holder.
Connect the wires as shown in Figure 33.
Push the buttons on each of the stations to ensure that the valve is in the “closed” position.
Turn the water supply back on and check for leaks.
Push the buttons on each of the stations to flush the air out of the system and verify that the
buttons correspond.
ELECTRONICS PACK
BLACK
TO (-)
269-1612CS (60 seconds)
269-1612DS (180 seconds)
RED
TO (+)
SOLENOID
269-1612VS
S83-169
CRP2 6-Volt LITHIUM
BATTERY REQUIRED
(1) PER BATTERY HOLDER
+
SW1
SW2
INLINE
FILTER
269-1612C (60 seconds)
269-1612D (180 seconds)
BLACK TO
(SW1)
S83-161 FOR
WALL SAVERS
S83-160 FOR
OTHER WALL SHOWERS
WHITE TO
(SW2)
Figure 33
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
85
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Battery Touch Time Troubleshooting
(Figure 33)
Troubleshooting
— Flush supply line before making connections —
PROBLEM
SOLUTION
1.
2.
No Water coming out at all
3.
4.
5.
If Low or No Flow (and you can
hear solenoid click/working).
1.
Water flows only short time length.
1.
2.
3.
2.
3.
1.
Water does not shut off.
If battery has too short of a life.
1.
Hold button in for minium 1 second, then release.
Check battery and connections for loose connections or
corrosion, and battery for low voltage — Correct as needed.
Disconnect switch connectors. Jumper accross switch SW2 to SW1 on valve
for minium 1 second. — Remove jumper.
If valve activates — Replace or service the switch.
Check inline filter in valve — Clean if required.
Remove the electronics pack. — Connect the power to the solenoid directly.—
Reversing the power connections will close the solenoid. — If the solenoid is OK,
replace the electronics pack — If the solenoid is bad, replace the valve assembly.
Check battery and connections for loose connections or
corrosion, and battery for low voltage — Correct as needed.
Check inline filter in valve — Clean if required.
Remove shower/spray head and clean.
Check battery and connections for loose connections or
corrosion, and battery for low voltage — Correct as needed.
Check timing printed on valve.
Replace electronics pack of valve.
2.
3.
4.
Check battery and connections for loose connections or
corrosion, and battery for low voltage — Corrcct as needed.
Check inline filter in valve — Clean if required.
Check timing printed on valve.
Remove the electronics pack.— Connect the power to the solenoid directly. —
Reversing the power connections will close the solenoid. — If the solenoid is OK,
replace the electronics pack — If the solenoid is bad, replace the valve assembly.
1.
2.
Check battery holder, wires and connections for corroision or damage.
Replace electronics pack of valve.
2.
If the solenoid is removed from the valve assembly for ease of service of the electronic pack, the solenoid
must return to its orginal valve base.
If the Power - Battery is removed from the unit, the valve will remain in which ever position it was
in (open or closed). If open, reconnecting power will let the timer continue until the timer closes the valve.
There is no way to change or reset the timer.
*
Warning:
Do not turn screw and/or nut on the top end of the solenoid. This is a precision adjustment
made at the factory.
*
SOLENOID
ELECTRONICS
PACK
VALVE
BASE
+
SW1
86
SW2
INLINE
FILTER
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Bradley Showers
Bradley Shower Warranty Information
Product warranties may be found under “Product Information” on our website at www .bradleycorp.com
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
87
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Bradley Thermostatic Mixing Valve
(Figure 2)
Repair parts are no longer available from Bradley. Contact Powers,a Watts Industries co.,
their model 425 Hydroguard.
Figures courtesy of Powers, a W atts Industries Co.
88
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Compression Shower Valves 1049 to Present
(Figure 27)
NOTE: Complete valve assemblies are not shown. Only those parts reflecting basic design changes are illustrated.
128-011 Handle "Hot"
128-012 Handle "Cold"
125-001L
Bibb Washer
VALVE ASSEMBLY NO. S02-018
Furnished from 1949 to 1963.
Only the 125-001L & 160-146 are still available.
160-001 or
160-146 Screw
119-008 Valve Stem
Valve Assembly S02-031 (Tempered), S0-2031A (Cold), S02-031B (Hot)
125-001L
Bibb Washer
128-021 Handle
160-146
Screw
119-042 Valve Stem
125-001L
Bibb Washer
128-028 Handle
160-146
Screw
119-050 Valve Stem
128-028 Handle
119-052 Valve Stem
125-001L
Bibb Washer
120-017 160-146
Valve Stem Screw
Extension
Available as S21-020
valve stem assembly
First S02-031 Series
Furnished from 1963 to 1968.
Only the 125-001L & 160-146
are still available.
REPAIR KIT NO. S45-048
CONTENTS
Qty
1
1
1
1
1
1
Part No.
160-146
125-001L
124-001BD
125-001BC
117-002
124-001K
Item
Screw
Bibb Washer
Fibre Washer
"O" Ring
Renewable Valve Seat
Valve Body Washer
REPAIR KIT NO. S45-048
CONTENTS
Second S02-031 Series
Furnished from 1968 to 1969.
Only the 128-028, 125-001L
& 160-146 are still available.
Qty
1
1
1
1
1
1
Part No.
160-146
125-001L
124-001BD
125-001BC
117-002
124-001K
Item
Screw
Bibb Washer
Fibre Washer
"O" Ring
Renewable Valve Seat
Valve Body Washer
REPAIR KIT NO. S45-048A
CONTENTS
Third S02-031 Series
Furnished since 1969.
Only the third S02-031
Services can be provided
complete, either as an
assembly, or as individual
parts.
Qty
1
1
1
1
1
1
1
Part No.
120-017
160-146
125-001L
124-001BD
124-001K
125-001BC
117-002
Item
Valve Stem Extension
Screw
Bibb Washer
Fibre Washer
Washer
"O" Ring
Renewable Valve Seat
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
89
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Metered Shower Valve S27-024
Operation and Service Instructions
(Figure 28)
Valve Adjustment:
By referring to the valve diagram, follow these instructions for valve adjustment. The diagram shows
the valve set at maximum time cycles the Allen set screw is holding on the uppermost end of pushrod. To shorten cycle:
1. Loosen the Allen set screw.
2. "Pop out" plug bottom with sharp pointed tool.
3. Insert thin blade screwdriver in center of knob and into the slot of the push-rod.
4. Turn knob clockwise while holding screwdriver firmly. Turn until push-rod is almost flush with
top of knob.
5. Tighten Allen set screw. Insert plug bottom.
This procedure lowers the knob in the cap and effectively allows for shorter stroke when the knob is
pushed to operated the valve.
SERVICE NOTES: Foreign matter in new pipe lines may interfere with proper operation of valve
and may be corrected by removing cartridge and cleaning working parts of valve. If valve has long
idle period between installation and operation, Cup Washer or Push-rod may stick and it may be
necessary to disassemble valve end of cartridge and lightly lubricate these parts. The same procedure may be found necessary on installations which have only seasonal use.
90
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Operation and Service Instructions
Bradley Showers
Metered Shower Valves S27-023
Bradley Metered Shower Valve
S27-023 for column showers &
repair parts is no longer available.
Bradley’s Metering to Touch ’N Flo Conversion Kits are No
Longer Available as well as the On-Site Machining Tool
S45-347:
2 to 5 Person Column . . . . . .S45-321 (No longer availble)
6 Person Column . . . . . . . . . .S45-322 (No longer available)
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
91
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Pos-I-Pak Valves
Operation and Service Instructions
(Figure 30)
Individual Showers — Concealed
Used from January 1978 to March 1983.
Components no longer available.
Single Tempered Supply Uses Washer 142-027
And Valve Unit S27-157.
PARTS LIST
No.
1
2
3
4
5
6
7
8
Part
160-261
128-049
142-002BL
169-743
169-742
169-650
125-001BC
S27-157
9
S27-157A
10
11
12
13
125-001BY
169-741
142-027A
142-027B
Description
Screw
Handle
Washer
Sleeve
Escutcheon
Cap
O-Ring 13/16 x 5/8
Valve Unit
(Includes 169-748 & 169-746)
Valve Unit
(Includes 169-748 & 169-746)
"O" - Ring 1/2 x 3/8
Waterway Sleeve
Washer — Cold (Blue)
Washer — Hot (Red)
HOT & COLD VALVES
Individual Showers — Concealed
Used from March 1983 To Present.
Single Tempered Supply Uses Washer 142-027.
PARTS LIST
No.
1
2
3
4
5
6
8
9
10
11
12
13
14
15
92
Part
119-052
S21-021
142-002BL
160-145
142-027B
142-027A
128-060
121-019
125-001BC
124-001BD
142-002BF
113-430
150-110
117-034
Description
Valve Stem
Extension
Insert Washer
Screw
Red Washer
Blue Washer
Handle
Bonnet
"O" - Ring
Fiber Washer
Brass Washer
Sleeve
Escutcheon
Seat
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Pos-I-Pak Valve
(Figure 31)
(Obsolete)
NOTE: To convert to current style compression, order S45-849
for columns — S45-850
Does not include handle, screw or index washer.
Washer
142-002BL
Escutcheon
150-067
Valve Body
118-111
Washer
124-001K
Valve Seat
*117-026
**117-027
Washer
142-027 Temp.
142-027A Cold
142-027B Hot
Screw
160-145
Handle
128-028
Valve Unit
S27-157
*For Wall-Saver, Econo-Wall and Panelon.
for wall mounted.
Bonnet
121-018
Adaptor
153-139
**For Column Shower
S27-113 Gradual Closing Valve
No longer available, Contact Chicago Faucet — Ref. #333-X-SLO
S27-115A Self-Closing Valve
PARTS LIST
No. Qty. Part
1
1
169-580
2
1
169-581
3
1
169-582
4
1
169-583
5
2
169-584
6
1
169-585
7
1
169-586
8
1
169-587
9
1
169-588
10
1
169-589
11
1
169-590
12
1
169-591
13
1
169-592
14
1
169-593
15
1
169-594
16
1
169-595
17
1
160-118
Description
Cap Nut
Samson Nut Sleeve
Samson Nut, R.H. Thread
Samson Nut, L.H. Thread
Brass Washer
Handle
Ball Race
Centerpiece
Asbestos Washer
Packing
Spring
Gland
Spring
Stem
Seat Washer
Seat Washer Screw
Set Screw
Used in Conjunction With The Following:
118-088
Valve Body
124-001K Fiber Washer
142-028
Ecutcheon Washer
117-002
Valve Seat
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952
93
VDC SPECIALTY PLUMBING PRODUCTS
Web: vdcspecialtyplumbingparts.com
VESCERA DISTRIBUTING COMPANY, Inc.
2910 Burnet Ave ~ Syracuse, NY 13206 ~ (800) 875-7952 ~ Fax: (315) 422-9125 ~ email: sales@vdcspecialtyplumbingparts.com
Bradley Showers
Operation and Service Instructions
Cleaning and Maintenance Instructions
IMPORTANT: Never use ordinary steel wool or steel brushes on st ainless steel.
Always use stainless steel wool or stainless steel brushes.
IMPORTANT: Do not permit salty solutions to evaporate and dry on st ainless steel.
IMPORTANT: Strongly acidic or caustic cleaners may att ack the steel causing a reddish film to appear. The use of these cleaners should be avoided.
Step 1: Cleaning stainless steel
NOTE: Rubbing should be in the direction of polishing lines.
1. Remove ordinary deposits of dirt and grease with soap and water.
2. Thoroughly rinse and dry the metal after washing.
3. Use stainless steel polishing powder to remove tightly adhering deposits.
NOTE: Sometimes the appearance of rust on stainless steel leads to the belief that the stainless steel is
rusting. A steel nail or screw may cause the trouble.
4. Look for sources of rust in some iron or steel not actually a part of the stainless steel structure.
IMPORTANT: Strong alkaline or acid-based chemicals and cleaners should not be
used to clean Terreon®. If these chemicals come in cont act with the
Terreon® surface, wipe off the surface immediately and flush with
soapy water.
Enamel
Enameled fixtures may be cleaned with any commercial detergent, liquid or powered, as long as it
contains no abrasive materials which will scratch the surface.
Enameled pedestal panels and shower columns can be coated with a high grade automobile wax to
protect their finish.
Shower Head Cleaning
If showerhead delivers an uneven spray, remove showerhead, disassemble, and remove foreign
matter.
Shower Drain Cleaning
Drain can be cleaned with plumbers snake inserted through hand hole of column.
94
FOR MORE INFORMATION OR TO PLACE A ORDER CALL 800-875-7952