Instructions for use

User Manual
GB
iZi Sleep ISOfix
www.izisleep.com
Complies with revised
standard:
ECE R44/04
Tested and Approved
AIRBAG
EXTREME HAZARD:
Do not use on
passenger seats fitted
with activated airbag
04443714
Thank you for choosing BeSafe iZi Sleep ISOfix
!
It is important that you read this user manual BEFORE
installing your iZi Sleep ISOfix. Incorrect installation could
endanger your child.
Safety and convenience
As you and we know, safety comes first when children are
involved. For that reason the iZi Sleep ISOfix complies to
and exceeds the highest safety requirements.
In order to provide as much convenience as possible, the
iZi Sleep seat introduces its innovative reclining-system:
outside the car, your child can comfortably rest and sleep
in the iZi Sleep, being put completely flat.
!
DO NOT use the seat in sleeping position when installed in
your car.
‘Safe-to-drive’ indication
don’t drive
don’t drive
safe-to-drive
‘safe-to-drive’
indication on
handle-rotation
knob
Contents
Vital information
iZi Sleep ISOfix usage
Preparing to install
Fitting your child in the iZi Sleep
ISOfix installation
Warning: Potential misuse
Removing ISOfix Sleeping position
After an accident
Guarantee
Important advise
Point of sale information
3
4
5
6
8
12
13
16
17
17
18
20
Vital information
!
- EXTREME HAZARD - DO NOT use on a passenger
seat fitted with activated airbag.
AIRBAG
- Rear facing installation only.
- DO NOT use the iZi Sleep ISOfix in sleeping position when installed in your car.
- ONLY use the iZi Sleep ISOfix on forward facing car seats.
iZi Sleep ISOfix usage
Check the car manufacturers
handbook f������������
or detailed
information on ISOfix.
safe-to-drive
For belt installation and
product care see iZi Sleep
manual.
Without the ISOfix base the
iZi Sleep can be installed with
the car belt.
Positioning in car:
Rear facing installation:
AIRBAG
The iZi Sleep ISOfix is
Only rear facing installation
suitable for fixing into the
allowed.
seat positions of the cars
listed in the appendix ‘carlist’.
Preparing to install
Crucial parts
1 Instruction label
2 Storage user manual
3 Base
����
4 Connector
��������������������������
release switches
5 Connectors
6 Insertion clips 2x (bottom side)
7 iZi Sleep release switches
8 Floor support release switch
9 Floor support
Second-hand iZi Sleep ISOfix
BeSafe advices that child seats should not be bought or
sold second-hand. Many seats sold through local advertising
have been found to be dangerous.
Fitting your child in the iZi Sleep
When the child weighs over 13kg or the child’s head grows
above the seat, the child should change to the iZi Comfort
group 1 seat or the iZi Combi group 0/1 seat.
You must adjust the shoulder belt of the harness to the
correct position for your child before installing the seat.
The harness must be fastened and adjusted correctly at all
times. Children should be encouraged to remain within the
harness system.
!
1
Too high
2
Too low
Correct
Position of the shoulder belt:
Check that the shoulder belt
slots are level with your
child’s shoulders.
Adjusting the shoulder belts:
Open the storage compartment
on the back of the iZi Sleep.
Detach the shoulder belt
adjuster, and place it in the
correct position by supporting
the belt from the inside. (see
illustration above). Make sure
adjuster is clicked in.
Fastening the harness:
Lay the shoulder belts over
the sides of the iZi Sleep,
before your child is seated.
Put the child in the seat.
3
Place the belts over the
shoulder and close the
harness buckle. Pull the
central adjuster straight
down. Just two fingers
should fit between child and
shoulder belt. Make sure
the belts are not twisted.
ISOfix installation
!
Make sure the indicators on the connector release switches
are green before you drive.
!
Make sure the floor support is fully pushed down.
!
EXTREME HAZARD - DO NOT use on a passenger
seat fitted with activated airbags.
6
1
Clip the insertion clips (6)
onto the ISOfix anchorage
points on the vehicle
seat (between seat and
backrest). The insertion
clips should be removed
when not in use.
6
2
AIRBAG
Release the floor support
(9) from underneath the
base (3).
Do this outside the car.
3
9
3
Place the base on the
car seat. Click the ISOfix
connectors (5) in the ISOfix
anchorages (a). Make
����������
sure
both indicators on the
connector release switches
(4) are GREEN.
click
a
5 4
4
Unlock the floor support
release switch (8) and push
the floor support (9) down
till it has contact with the
floor of the car.
8
click
9
Continue with step 5, on the next page.
5
Place the iZi Sleep on the
base (3). Check if the iZi
Sleep release switches (7)
are up and indicates green.
If the switch is not up and
does not indicate green
check if the floor support
(9) is folded out (step 2).
7
3
9
safe-to-drive
6
Move the carrying handle
to the ‘safe-to-drive’
position by pushing the
handle release buttons on
the inside of the handle.
Push the carrying handle
towards the car seat as
far as possible. There are
two safe-to-drive positions
A and B.
A B
safe-to-drive
Check the ‘safe-to-drive’
indication on the carrying
handle, near the handle
release button.
don’t drive
‘safe-to-drive’ indication on
handle-rotation knob
10
Correct installation
All six indicators (three left and three right) must
show green!
safe-to-drive
11
Warning: Potential misuse
!
Installation behind an
actived airbag is forbidden.
AIRBAG
!
!
Carrying handle in carrying
position is forbidden, “safeto-drive” indication is red.
!
Never use the car seat belt
in combination with the iZi
Sleep ISOfix base.
Always fold out the floor
support. The iZi Sleep
release switch must show
green.
12
Removing iZi Sleep ISOfix
1
Move the carrying handle
to the carrying position by
pushing the handle release
buttons on the inside of the
handle.
2
Remove the iZi Sleep while
pressing one of the
iZi Sleep release switches
(7).
7
13
To release the ISOfix
anchorages, pull the
connector release switches
(4) on both sides.
Afterwards the indicators
should show red.
3
4
4
Unlock the floor support
release switch (8) and push
the floor support (9) fully
up.
8
9
5
Take the iZi Sleep ISOfix
base out of the car.
14
6
Store the floor support (9)
underneath the base (3).
3
click
9
7
Remove the insertion clips
from the vehicle seat and
store them underneath the
base.
15
Sleeping position
!
DO NOT use the seat in sleeping position when installed in
your car.
Your child can comfortably rest and sleep in the iZi Sleep,
when put in the sleeping position (only outside the car) .
To put the iZi Sleep into the sleeping position, push both
handle release buttons on the inside of the carrying handle
and move the handle to the head of the iZi Sleep.
Cleaning the iZi Sleep ISOfix
Do not use any aggresive cleaning products; these may
harm the construction material of the iZi Sleep. Clean by
hand with water and mild soap.
16
After an accident
After an accident, the iZi Sleep and the ISOfix base should
be replaced. Although they may look undamaged, if you
were to have another accident, the iZi Sleep and the ISOfix
base may not be able to protect your child as well as they
should.
Guarantee
All BeSafe products are carefully designed, manufactured
and tested. All BeSafe child safety seats are tested
periodically out of our continuous production in our test
laboratory. Furthermore they are tested by independent
test institutes.
Should this product prove faulty within 24 months of
purchase due to materials or manufacturing fault, except
covers and child safety belt, please return it to the original
place of purchase.
The guarantee is only valid when you use your seat and
ISOfix base appropriately and with care. Please contact
your dealer, he will decide if the seat will be returned to
the manufacturer for repair. Replacement or return cannot
be claimed. The guarantee does not get extended through
repair.
The guarantee expires:
- When there is no receipt.
- When defects are caused by wrong and improper use .
- When defects are caused by abuse, misuse or negligence.
17
Important advice
!
- Be aware of the ‘safe-to-drive’ indication.
- Make sure both the internal child safety belts are
tightened firmly, in order to prevent any unwanted
dislocation of child. Check frequently.
- DO NOT use anything, such as a cushion or coat, to raise
the iZi Sleep ISOfix off the passenger seat. In an accident
the iZi Sleep ISOfix will not be able to protect your child as
well as it should.
- All passengers should be fastened by a safety belt.
- Make sure all passengers are informed on how to release
your child in case of emergency.
- Make sure luggage or other objects are properly secured.
- Unsecured luggage may cause severe injuries to children
and adults in case of accidents
- Rigid items and plastic parts of the iZi Sleep and ISOfix
base must be so located and installed that they are not
liable, during everyday use of the vehicle, to become
trapped by a movable seat or in a door of the vehicle.
- An unoccupied iZi Sleep and ISOfix base should still be
fastened.
- DO keep this user manual in the storage component of the
base.
- DO NOT attempt to dismantle, modify or add any part of
the iZi Sleep ISOfix.
- Warranty will expire if non-original parts or accessories are
used.
18
- DO NOT use the iZi Sleep and ISOfix base for longer than
5 years. Due to ageing, the quality of the material may
change.
- Never leave your child unattended in the iZi Sleep.
- Your child shall allways be secured with the internal child
safety belts when seated in the iZi Sleep, also by carrying
and when used as traveling system.
- DO make sure the handle is upright and locked properly
before carrying your baby in the iZi Sleep.
- DO NOT place the iZi Sleep child safety seat on a table or
worktop as long as your child is seated in the iZi Sleep.
- The cover is a safety feature. Never use the iZi Sleep
without the original cover.
- The cover of the iZi Sleep should be washed in accordance
with the instructions.
- Do not use any aggresive cleaning products; these may
harm the construction material of the iZi Sleep ISOfix.
- iZi Sleep ISOfix can not be placed on the base when the
floor support is folded in.
- We recommend using BeSafe protection cover under your
child safety seat to avoid cuts, marks or decolouring on
the interior of the car and especially in cars with leather
interior.
19
Point of sale information
Notice:
1. This is an ISOFIX CHILD RESTRAINT SYSTEM. It is
approved to Regulation No. 44.04 series of amendments
for general use in vehicles fitted with ISOFIX anchorages
systems.
2. It will fit vehicles with positions approved as ISOfix
positions (as detailed in the vehicle handbook), depending
on the category of the child seat and of the fixture.
3. The mass group and the ISOfix size class for which this
device is intended is: group 0+ (0-13 kg)
4. This child restraint is classified for semi-universal use
and is suitable for fixing into the seat postions of the cars
mentioned in the carlist.
!
!
EXTREME HAZARD - DO NOT use on a passenger seat
fitted with activated airbags.
DO NOT use the seat in sleeping position when installed in
your car.
GB - 2007 - V 6.2
B315_N2000970
for more information:
N-3535 Krøderen, Norway
www.besafe.eu
www.hts.no