ACS-2695 Box PC
User Manual
Release Date
Revision
Nov. 2012
® 2012 Aplex Technology, Inc.
V1.0
All Rights Reserved.
Published in Taiwan
Aplex Technology, Inc.
15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan
Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw
ACS-2695 User Manual
URL: www.aplex.com.tw
1
Warning!_______________________________
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used in accordance with the instructions manual, it may cause interference to radio
communications.
It has been tested and found to comply with the limits for a Class A computing device pursuant to
FCC Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely
to cause interference in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed. There are
dangerous high voltages inside.
Disclaimer
This information in this document is subject to change without notice. In no event shall Aplex
Technology Inc. be liable for damages of any kind, whether incidental or consequential, arising
from either the use or misuse of information in this document or in any related materials.
ACS-2695 User Manual
2
Packing List
Accessories (as ticked) included in this package are:
□ AC power cable
□ Driver & manual CD disc
□ Other.___________________(please specify)
Safety Precautions
Follow the messages below to avoid your systems from damage:
◆ Avoid your system from static electricity on all occasions.
◆ Prevent electric shock. Don‘t touch any components of this card when the card is
power-on. Always disconnect power when the system is not in use.
◆ Disconnect power when you change any hardware devices. For instance, when you
connect a jumper or install any cards, a surge of power may damage the electronic
components or the whole system.
ACS-2695 User Manual
3
Table of Contents______________________
Warning!…………………………………………………………………………….……..….2
Disclaimer………………………………………………………………….…………………2
Packing List...................................................................................................................3
Safety Precautions........................................................................................................3
Chapter 1
Getting Started
1.1 Specifications………………………………………….………….……...…..6
1.2 Dimensions…………………………………...……………….…………......7
1.3 Brief Description ……………….……..………………….………………11
1.4 Installation of HDD................................................................................12
1.5 Installation of PCI Add-on.....................................................................13
1.6 Installation of Wall Mount Bracket.........................................................14
Chapter 2
Hardware Installation
2.1 Mainboard Specifications………………………..…………….…………19
2.2 Jumpers Setting and Connectors………………………….……………24
Chapter 3
BIOS Setup
3.1 Operations after POST Screen.............................................................55
3.2 BIOS SETUP UTILITY..........................................................................55
3.3 Main Settings........................................................................................56
3.4 Advanced Settings................................................................................57
3.5 Chipset Settings................................................................................... 66
3.6 Boot Settings........................................................................................75
3.7 Security Settings...................................................................................76
3.8 Save & Exit Settings.............................................................................77
Chapter 4
Installation of Drivers
4.1 Intel Chipset Driver.…………………………...………….………………81
4.2 Intel VGA Chipset Driver..…....…......……………………………….......84
4.3 Intel 82574L Network adapter Driver……..............................................90
4.4 Realtek HD Audio Driver Installation………………………….….……93
ACS-2695 User Manual
4
4.5 Microsoft .NET Framework 3.5 Service Installation…………………...95
Figures
Figure 1.1: Dimensions of the ACS-2695 (DC input)………………………...7
Figure 1.2: Dimensions of the ACS-2695 (DC input / DVD Device)…………8
Figure 1.3: Dimensions of the ACS-2695 (AC input).....................................9
Figure 1.4: Dimensions of the ACS-2695 (AC input / DVD Device).............10
Figure 1.5: Left-front View of ACS-2695……………………………….......11
Figure 1.6: Right-front View of ACS-2695………….………………………....11
Figure 1.7: Wall Mount of ACS-2695 Type 1...............................................14
Figure 1.8: Wall Mount of ACS-2695 with DVD Device Type 2....................15
Figure 1.9: Wall Mount of ACS-2695 with DVD Device Type 3....................16
Figure 1.10: Wall Mount of ACS-2695 Type 4.............................................17
Figure 1.11: Wall Mount of ACS-2695 Type 5..............................................18
Figure 2.1: Mainboard Overview………………………………..……..………19
Figure 2.2: Mainboard Dimensions……………………………………………19
Figure 2.3: Jumpers and Connectors Location-TOP…………………...……20
Figure 2.4: Jumpers and Connectors Location- Bottom………………….…21
ACS-2695 User Manual
5
Chapter 1________________Getting Started
1.1 Specifications
Specs
ACS-2695
CPU
Socket G2, 2nd Generation Intel Core i7/i5/i3, up to i7 2620M
System Chipset
Intel QM67 PCH
System Memory
2 x 204 Pin DDR3 SO-DIMM, default 4GB (one slot), up to 16GB
1066/1333MHz
External I/O Port
2 x DB9 RS-232 (COM1.2)
1 x DVI-I
2 x RJ45 GbE LAN
4 x USB 2.0
1 x Mic-in, Line-Out
1 x DC Power 3 Pin terminal block connector
1 x 2 pin power switch connector
1 x Power button switch
1 x COM RS-422/485 (COM3, default:RS-485)
1 x COM RS-232 (COM4)
1 x 10 Pin terminal block for 1 Ground/VCC/ 4 in & out DIDO
Expansion Slots
Storage
1 x PCIe x16 and 1 x PCI Slot
2 x 2.5" SATA HDD Space
1 x External CF Slot
Power Supply
Construction / Color
Mounting
Dimensions(WxHxD)
9~32V DC, AC Power Input for option
Steel and Aluminum Heatsink
Wall Mount, Din Rail Mount for option
211.2x203.5x155 mm
211.2x203.5x177 mm (with DVD Device)
Net Weight
Operating Temperature
Storage Temperature
Storage Humidity
Vibration
5.9kgs
0~50 °C
-20~60 °C
10%~90%@ 40℃, non-condensing
5G, 5-500MHz, 3 Axes (with CF or SSD)
0.5G 5-500MHz, 3 Axes (with HDD)
Shock
Drop
Certificate
ACS-2695 User Manual
50G Half sine (11 msec. duration)/operation with SSD
92cm (1 Corner, 3 Edge, 6 Surface)
CE / FCC Class A
6
1.2 Dimensions
Figure 1.1: Dimensions of the ACS-2695 (DC input)
ACS-2695 User Manual
7
Figure 1.2: Dimensions of the ACS-2695 (DC input with DVD Device)
ACS-2695 User Manual
8
Figure 1.3: Dimensions of the ACS-2695 (AC input)
ACS-2695 User Manual
9
Figure 1.4: Dimensions of the ACS-2695 (AC input with DVD Device)
ACS-2695 User Manual
10
1.3 Brief Description of the ACS-2695
The ACS-2695 is a Fan-less High-efficiency Thermal Solution Box PC, powered by Socket G2, 2nd
Generation Intel Core i7/i5/i3 processor and supporting 4 x USB 2.0 ports, 4 x COM Ports, 1 x DVI-I,
support 2 x SATA HDD space, 1 x external CF slot, 9~32V wide-ranging power input etc. It is ideal for
Industrial Automation, Factory Automation, Machine Vision, Process Control, Data Terminal, TI,
Surveillance, etc. and running factory operations from small visual interface and maintenance
applications to large control process applications. The ACS-2695 works very well along with any of our
Display series and it absolutely can provide an easy way to perform control and field maintenance.
Figure 1.5: Left-front View of ACS-2695
Figure 1.6: Right-front View of ACS-2695
ACS-2695 User Manual
11
1.4 Installation of HDD
Step 1
There is one screw which connects to the
chassis. Pull out the chassis towards the I/O
side after unscrewing as shown in the picture
ACS-2695
Step 2
There are 2 screws to deal with when
enclosing or removing the HDD bracket as
shown in the picture ACS-2695
Loosen screw and draw the HDD bracket
out as shown in the picture ACS-2695
Step 3
Tighten the 1 screw as shown in the picture.
That’s how it should look after it has been
installed.
ACS-2695 User Manual
12
1.5 Installation of PCI Add-on
Step 1
There is one screw which connects to the
chassis. Pull out the chassis towards the I/O
side after unscrewing as shown in the picture
ACS-2695
Step 2
Now slide the add on into the PCI slot,
making sure the golden part faces the slot.
When the part that is interfaced together
come into the right contact, slightly push the
add on into the rail of the slot.
After sliding the add on into the PCI
expansion slot, get the one screw as circled
tightened to finish the connection.
** Half Expansion-card limit to be not more
than 175mm length
Step 3
Tighten the 1 screw as shown in the picture.
That’s how it should look after it has been
installed.
ACS-2695 User Manual
13
1.6 Installation of Wall Mount Bracket
Figure 1.7: Wall Mount of ACS-2695 Type 1
ACS-2695 User Manual
14
Figure 1.8: Wall Mount of ACS-2695 with DVD Device Type 2
ACS-2695 User Manual
15
Figure 1.9: Wall Mount of ACS-2695 with DVD Device Type 3
ACS-2695 User Manual
16
Figure 1.10: Wall Mount of ACS-2695 Type 4
ACS-2695 User Manual
17
Figure 1.11: Wall Mount of ACS-2695 Type 5
ACS-2695 User Manual
18
Chapter 2__________Hardware Installation
2.1 Mainboard Specifications
Figure 2.1: Mainboard Overview
Figure 2.2: Mainboard Dimensions
ACS-2695 User Manual
19
Figure 2.3: Jumpers and Connectors Location-TOP
ACS-2695 User Manual
20
Figure 2.4: Jumpers and Connectors Location- Bottom
ACS-2695 User Manual
21
Specifications
Board Size
170mm x 170mm
CPU Support
Support Socket G2,2nd Gen Intel Core i3/i5/i7 Processor
Chipset
Intel QM67
Memory
Support
2 x SO-DIMM (204pins), up to 16GB DDRIII
1066/1333/1600MHz FSB
Graphics
Intel HD Grapics 2000/3000
Super I/O
Winbond W83627UHG
BIOS
AMIBIOS 16M
Storage
1 x SATA2.0 Connector
1 x SATA2.0 Connector
(option)
2 x SATA3.0 Connector
1 x CFAST Slot (option)
1 x MSATA Connector
(option)
Ethernet
2 x PCIe Gbe LAN by Intel 82574L
USB
4 x USB 2.0 stack ports for external
3 x USB 2.0 box Pin header for MIO1
4 x USB 2.0 box Pin header for MIO2
1 x USB 2.0 internal for mini PCIe
1 x RS232/422/485 port, DB9 connector for external (COM1)
pin 9 w/5V/12V/Ring select
Serial
1 x RS232 port, DB9 connector for external (COM2)
pin 9 w/5V/12V/Ring select
1 x RS232 header for internal (COM5)
1 x RS232 header for internal (COM6), pin 9 w/5V/12V select
I/O Card TB-522 (option):
1 x 422/485 select header for internal MIO1 (COM3)
1 x RS232 header for internal MIO1 (COM4)
I/O Card TB-523 (option):
1 x 422/485 select header for internal MIO1 (COM3)
1 x RS232/422/485 select header for internal MIO1 (COM4)
Digital I/O
8-bit digital I/O by Pin header by MIO2
4-bit digital Input
4-bit digital Output
Battery
Support CR2477 Li battery by 2-pin header
Support CR2032 Li battery (option)
Audio
Support Audio via Realtek ALC662 HD audio codec
ACS-2695 User Manual
22
Support Line-out, MIC by JACK1
Support Line-in, Line-out, MIC by 2x6-pin header
Keyboard
/Mouse
PS2 K/B and Mouse by MIO2
1 x PS/2 keyboard
1 x PS/2 mouse
Expansion Bus
1 x PCI-express x16 extend by 4x30 pin socket
2 x PCI-express x1 extend by 4x10 pin socket
1 x mini-PCI-express slot
1 x CRT 2x5 Pin Header
Power
Management
1 x 3-pin power input connector (Wide range DC+9V~32V)
1 x ATX Power Input (2x2Pin and 3Pin, option)
DC5V/12V output by 1x4 pin Connectors
Switches and
LED Indicators
Power on/off switch by TB-522 or TB-523
Reset switch by MIO2
Power LED status by MIO2
HDD LED status by MIO2
External I/O
port
Watchdog
Timer
2 x COM Ports (COM1/COM2)
4 x USB 2.0 Ports (stack)
2 x RJ45 GbE LAN Ports
1 x DVI-I Port
1 x Audio Ports (Mic, Line out)
Software programmable 1 – 255 second by Super I/O
Temperature
Operating: -20℃ to 70℃
Storage: -40℃ to 85℃
Humidity
10% - 90%, non-condensing, operating
Power
Consumption
EMI/EMS
ACS-2695 User Manual
12V/3.80A (Intel i5-2430M 2.4GHz Processor with 4GB
DDR3)
19V/2.0A (Intel i5-2540 2.6GHz Processor with 8GB DDR3)
19V/2.2A(Intel i7-2620 2.7GHz Processor with 8GB DDR3)
Meet CE/FCC class A
23
2.2
Jumpers Setting and Connectors
1.
RTC1/SRTC1:
(2.0mm Pitch 1X2 Pin Header)CMOS clear jumper, CMOS clear operation will
permanently reset old BIOS settings to factory defaults.
RTC1/SRTC1
CMOS
Open or
(RTC1Pin1-SRTC1 Pin
close)
NORMAL (Default)
Close 1-2
Clear CMOS
Procedures of CMOS clear:
a) Turn off the system and unplug the power cord from the power outlet.
b) To clear the CMOS settings, use the jumper cap to close pins1 and 2 for about 3
seconds then reinstall the jumper clip back to pins open.
c) Power on the system again.
d) When entering the POST screen, press the <DEL> key to enter CMOS Setup
Utility to load optimal defaults.
e) After the above operations, save changes and exit BIOS Setup.
2.
BAT1 :
(1.25mm Pitch 1X2 box Pin Header) 3.0V Li battery is embedded to provide power for
CMOS.
3.
Pin#
Signal Name
Pin1
VBAT
Pin2
Ground
PS_SEL:
(2.0mm Pitch 1X3 Pin Header),ATX Power and AT Power jumper setting.
PS_SEL
Close 1-2
Close 2-3
ACS-2695 User Manual
Mode
ATX Power
(Default)
AT Power
24
4.
PS_ON:
(2.0mm Pitch 1X3 Pin Header),ATX Power and Auto Power on jumper setting.
5.
PS_ON
Mode
Close 1-2
Auto Power on
(Default)
Close 2-3
ATX Power
DCIN:
(5.08mm Pitch 1x3 Pin Connector),DC9V ~ DC32V System power input connector。
6.
ATX12V_IN
Pin#
Power Input
Pin1
DC+9V~32V
Pin2
Ground
Pin3
FG
(ATX Power option):
(2x2 Pin Connector),DC12V System power input connector.
ACS-2695 User Manual
Pin#
Power input
Pin1
Ground
Pin2
Ground
Pin3
DC+12V
Pin4
DC+12V
25
7.
ATX (ATX Power option):
(2.0mm Pitch 1X3 box Pin Header), connect PSON and 5VSB and Ground
signal,support ATX Power model. Reserved.
8.
Pin#
Signal Name
Pin1
ATX PSON
Pin2
ATX Ground
Pin3
ATX 5VSB
DC_OUT:
(2x2 Pin Connector),DC12V and DC5V System power output connector.
9.
Pin#
Power output
Pin1
DC+12V
Pin2
Ground
Pin3
Ground
Pin4
DC+5V
U1:
(Socket G2), installing the 2nd GEN intel Core i3/i5/i7CPU Socket.
10.
CPU_FAN1/SYS_FAN1:
(2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected directly
for use. You may set the rotation condition of cooling fan in menu of BIOS CMOS
Setup.
Pin#
ACS-2695 User Manual
Signal Name
1
Ground
2
VCC
26
3
Rotation
detection
Note:
Output power of cooling fan must be limited under 5W.
11.
A-DDR3/B-DDR3:
(SO-DIMM 204Pin socket), DDRIII memory socket, the socket is located at the top of the
board and supports 204Pin 1.5V DDRIII 1066/1333/1600MHz FSB SO-DIMM memory
module up to 16GB.
12.
VGA1:
(CRT 2.0mm Pitch 2X5 Pin Header), Video Graphic Array Port, Provide 2x5Pin cable
to VGA Port.
Signal Name
Pin#
Pin#
Signal Name
CRT_RED
1
2
Ground
CRT_GREEN
3
4
Ground
CRT_BLUE
5
6
Ground
CRT_H_SYN
C
7
8
CRT_DDCDAT
A
CRT_V_SYNC
9
10
CRT_DDCCL
K
13.
INVT1:
(2.0mm Pitch 1x6 box Pin Header), Backlight control connector for LVDS1.
Pin#
ACS-2695 User Manual
Signal Name
1
+DC12V
2
+DC12V
3
Ground
4
Ground
5
BKLT_EN
27
6
BKLT_CTRL
Note:
Pin6 is backlight control signal, support DC or PWM mode, mode select at BIOS CMOS
menu.
14.
LVDS1:
(1.25mm Pitch 2x20 Connector), For 18/24-bit LVDS output connector, Fully supported
by Intel QM67 chipset, the interface features dual channel 18/24-bit output.
Signal Name
Pin#
Pin#
VDD5
2
1
VDD5
Ground
4
3
Ground
VDD33
6
5
VDD33
LB_D0_N
8
7
LA_D0_N
LB_D0_P
10
9
LA_D0_P
Ground
12
11
Ground
LB_D1_N
14
13
LA_D1_N
LA_D1_P
16
15
LA_D1_P
Ground
18
17
Ground
LB_D2_N
20
19
LA_D2_N
LB_D2_P
22
21
LA_D2_P
Ground
24
23
Ground
LB_CLK_N
26
25
LA_CLK_N
LB_CLK_P
28
27
LA_CLK_P
Ground
30
29
Ground
32
31
LVDS_DOC_CLK
Ground
34
33
Ground
LB_D3_N
36
35
LA_D3_N
LB_D3_P
38
37
LA_D3_P
NC
40
39
NC
LVLVDS_DDC_DAT
A
ACS-2695 User Manual
Signal Name
28
17.
JP_DVI:
(2.0mm Pitch 1x2 Pin Header), Reserved.
18.
DVI-I:
(DVI-I Connector), Digital Visual Interface-Integrated connector.
19.
BT1:
POWER on/off Button, They are used to connect power switch button. The two pins
are
disconnected under normal condition. You may short them temporarily to realize
system
startup & shutdown or awaken the system from sleep state.
20.
JP1:
(2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select
signal out of pin 9 of COM1 port.
JP1 Pin#
21.
Function
Close 1-2
COM1 RI (Ring Indicator) (default)
Close 3-4
COM1 Pin9=+5V
(option)
Close 5-6
COM1 Pin9=+12V
(option)
JP1A:
(2.0mm Pitch 2x10 Pin Header),COM1 jumper setting, it provides selectable RS232 or
RS422 or RS485 serial signal output.
Function
RS232
ACS-2695 User Manual
JP1A Pin#
Close:
29
(Default)
22.
Pin1-3, Pin2-4,
Pin13-14
Pin7-9,
Pin8-10,
RS422
Close:
(option)
Pin3-5, Pin6-8, Pin9-11, Pin10-12,
Pin17-18
RS485
(option)
Close:
Pin3-5,
Pin6-8, Pin9-11, Pin10-12,
Pin15-16
Pin19-20
COM1:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a
direct connection to serial devices.
RS232 (Default):
Pin#
Signal Name
1
DCD#
(Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP1 select Setting
(RI/5V/12V)
RS422 (option):
Pin#
ACS-2695 User Manual
Signal Name
1
422_R+
2
422_R-
3
422_T-
4
422_T+
5
Ground
6
NC
30
7
NC
8
NC
9
NC
RS485 (option):
Pin#
23.
Signal Name
1
NC
2
NC
3
485-
4
485+
5
Ground
6
NC
7
NC
8
NC
9
NC
JP2:
(2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select
signal out of pin 9 of COM2 port.
JP2 Pin#
24.
Function
Close 1-2
COM2 RI (Ring Indicator) (default)
Close 3-4
COM2 Pin9=+5V
(option)
Close 5-6
COM2 Pin9=+12V
(option)
COM2:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a
direct connection to serial devices.
Pin#
ACS-2695 User Manual
Signal Name
1
DCD#
(Data Carrier Detect)
2
RXD (Received Data)
31
25.
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
JP2 select Setting
(RI/5V/12V)
COM5:
(2.0mm Pitch 2X5 Pin Header),COM5 Port, standard RS232 ports are provided. They
can be used directly via COM cable connection.
Signal
Pin# Pin#
Signal Name
Name
26.
DCD
1
2
RXD
TXD
3
4
DTR
Ground
5
6
DSR
RTS
7
8
CTS
RI
9
10
NC
JP3:
(2.0mm Pitch 1x3 Pin Header) COM6 setting jumper, pin 1~3 are used to select signal
out of pin 9 of COM6 port.
JP3 Pin#
27.
Function
Close 1-2
COM6 RI (Ring Indicator)
(default)
Close 3-4
COM6 Pin9=+5V
(option)
Close 5-6
COM6 Pin9=+12V
(option)
COM6:
(2.0mm Pitch 2x5 Pin Header), COM6 Port, standard RS232 ports are provided. They
can be used directly via COM cable connection. COM6 port is controlled by pins
No.1~3 of JP3,select output Signal 5V or 12v, For details, please refer to description of
JP3.
Signal Name
ACS-2695 User Manual
Pin#
Pin#
Signal Name
32
28.
DCD
1
2
RXD
TXD
3
4
DTR
Ground
5
6
DSR
RTS
7
8
CTS
JP3select
Setting
(RI/5V/12V)
9
10
NC
USB_LAN1/USB_LAN2:
USB4/USB5/USB12/USB13:(Double stack USB type A), Rear USB connector, it
provides up to 4 USB2.0 ports, speed up to 480Mb/s.
Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A.
If the external USB device current exceeds 1.5A, please separate connectors
into different Receptacle.
LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M RJ-45
Ethernet ports are provided. Used Intel 82574L chipset, LINK LED (green) and
ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the
Ethernet port indicate the activity and transmission state of LAN.
29.
JACK1:
(Diameter 3.5mm Double stack Jack), HD Audio port, An onboard Realtek ALC662
codec is used to provide high quality audio I/O ports. Line Out can be connected to a
headphone or amplifier, MIC is the port for microphone input audio.
ACS-2695 User Manual
33
30.
AUDIO1:
(2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 codec is
used to provide high-quality audio I/O ports. Line Out can be connected to a
headphone or amplifier. Line In is used for the connection of external audio source via
a Line in cable. MIC is the port for microphone input audio.
Signal Name
31.
Pin#
Pin#
Signal Name
SPK_OUTL_P
1
2
SPK_OUTR_P
SPK_OUTL_N
3
4
SPK_OUTR_N
FRONT_JD
5
6
LINE1_JD
LINE_IN_L
7
8
LINE-IN-R
MIC2_IN_L
9
10
MIC2-IN-R
Ground_AUD
11
12
MIC2_JD
LED3:
LED STATUS. Green LED for Motherboard Standby Power Good status, Yellow LED for
HDD status.
32.
LED2:
LED STATUS. Green LED for Motherboard Standby Power Good status.
33.
LED1:
LED STATUS. Green LED for Motherboard Power status,
ACS-2695 User Manual
34
34.
PCIE_16X (option):
(4x30 Pin), Riser Card expansion connector. Can expand support one PCIeX16 or two
PCIeX8 Signal.
ASB-M8671T:PCIE_16X connector in the top.
ASB-M8671B:PCIE_16X connector in the Bottom.
35.
PCIE1X (option):
(4x10 Pin),Riser Card expansion connector.Can expand support two PCIe Signal.
ASB-M8671T:PCIE1X connector in the top.
ASB-M8671B:PCIE1X connector in the Bottom.
36.
MODEL
PCIE16X / PCIE1X
ASB-M8671T
Top
ASB-M8671B
Bottom
M-PCIE1:
(Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices
with USB2.0, SMBUS and PCIe signal. MPCIe card size is 30x30mm or 30x50.95mm.
37.
H1/H2:
MPCIE1 SCREW HOLES, H1 for mini PCIE card (30mmx30mm) assemble. H2 for mini PCIE
card (30mmx50.95mm) assemble.
38.
BUZZER1:
Onboard buzzer.
39.
MIO1:
(DF13-40P Connector),For expand output connector, It provides two RS232 ports or
one RS485 port, three USB ports, one power led, one power button, via a dedicated
cable connected to TB-522 MIO1or TB-523 MIO1.
ACS-2695 User Manual
35
Function
Signal Name
Pin# Pin#
Signal Name
485+ /
422TX+
2
1
422RX+
485- / 422TX-
4
3
422RX-
3P3V_S0
6
5
Ground
WAN_LED
8
7
NC
5V_S5
10
9
5V_S5
RXD4
12
11
DCD4-
DTR4-
14
13
TXD4
DSR4-
16
15
Ground
CTS4-
18
17
RTS4-
5V_S5
20
19
RI4-
5V_USB_101
22
21
5V_S5
USB10_N
24
23
USB9_N
USB10_P
26
25
USB9_P
Ground
28
27
Ground
Ground
30
29
Ground
Power
LED
3P3V_S0
32
31
5V_USB_1011
PWR_LED-
34
33
USB11_N
Power
Button
MIO_PSON
36
35
USB11_P
Ground
38
37
Ground
NC
40
39
NC
COM3
RS422
or
RS485
COM4
Function
COM3
COM4
1
USB10
40.
USB9
USB11
MIO2:
(DF13-40P Connector),Front panel connector.
Function
Signal Name
Pin#
Pin#
Signal Name
Function
H_LED+
P_LED+
PWR-LED
2
1
HDD_LED
P_LED-
Ground
4
3
USB01_OC-
PSON+
MIO_PSON-
6
5
USB23_OC-
PSON-
Ground
8
7
RESET
RESET+
BUZZER-
10
9
BUZZER+
BUZZER+
GPIO_OUT PCH_GPIO68
1
12
11
PCH_GPIO12
GPIO_IN1
GPIO_OUT PCH_GPIO69
2
14
13
PCH_GPIO15
GPIO_IN2
GPIO_OUT PCH_GPIO70
3
16
15
PCH_GPIO58
GPIO_IN3
BUZZER-
ACS-2695 User Manual
36
GPIO_OUT PCH_GPIO71
4
PS2_Mous
e
USB3
USB1
18
17
PCH_GPIO75
5V_S5_USB
20
19
Ground
PS2_MSDAT
A
22
21
PS2_KBDATA
PS2_MSCLK
24
23
PS2_KBCLK
5V_S5_USB
26
25
5V_S5_USB
USB3_N
28
27
USB2_N
USB3_P
30
29
USB2_P
Ground
32
31
Ground
5V_S5_USB
34
33
5V_S5_USB
USB1_N
36
35
USB0_N
USB1_P
38
37
USB0_P
Ground
40
39
Ground
GPIO_IN4
PS2_K/B
USB2
USB0
Pin1- Ground: HDD LED, They are used to connect hard disk activity LED. The LED
blinks when the hard disk is reading or writing data.
Pin2- Pin4:
POWER LED, They are used to connect power LED. When the system
is
powered on or under S0/S1 state, the LED is normally on, when the system
is
under S4/S5 state, the LED is off.
Pin3:
USB01 OC-, “USB01_OC-“ Signal.
Pin5:
USB23 OC-,“USB23_OC-“ Signal.
Pin7- Ground: RESET Button, They are used to connect reset button. The two pins
are disconnected under normal condition. You may short them temporarily to
realize system reset.
Pin6- Pin8: POWER on/off Button, They are used to connect power switch button.
The two pins are disconnected under normal condition. You may short them
temporarily to realize system startup & shutdown or awaken the system from
sleep state.
Pin9- Pin10:
BUZZER, They are used to connect an external buzzer.
Pin11~Pin18: GPIO IN/GPIO OUT, General-purpose input/output port, it provides a
group of self-programming interfaces to customers for flexible use.
Pin19~Pin24: PS2 KB/MS, PS/2 keyboard and mouse port, the port can be connected
ACS-2695 User Manual
37
to
PS/2 keyboard and mouse via a dedicated cable for direct used.
Pin25~40: USB0/USB1/USB2/USB3, Front USB connector, it provides 4 USB ports
via
a dedicated USB cable, speed up to 480Mb/s.
Note:
When connecting LEDs and buzzer and GPIO and USB, pay special attention to the
signal polarity. Make sure that the connector pins have a one-to-one correspondence
with chassis wiring, or it may cause boot up failure.
41.
SATA_P1/SATA_P3:
(2.5mm Pitch 1x2 box Pin Header), Two onboard 5V output connectors are reserved to
provide power for SATA devices.
Pin#
Signal
Name
1
+DC5V
2
Ground
Note:
Output current of the connector must not be above 1A.
42.
SATA_P2/SATA_P4:
(2.5mm Pitch 1x4 box Pin Header), Two onboard 5V and 12V output connectors are
reserved to provide power for SATA devices.
SATA_P2 (2Pin or 4Pin)
Pin#
Signal Name
1
+DC5V
2
Ground
3
Ground
(NC)
4
+DC12V
(NC)
SATA_P4 (option)
Pin#
ACS-2695 User Manual
Signal Name
38
1
+DC5V
(NC)
2
Ground
(NC)
3
Ground
(NC)
4
+DC12V
(NC)
Note:
Output current of the connector must not be above 1A.
43.
SATA1/SATA2/SATA3/SATA4:
(SATA 7P), SATA Connectors, Four SATA connectors are provided,SATA3 and SATA4
transfer speed up to 3.0Gb/s, SATA1 and SATA2 transfer speed up to 6.0Gb/s,
RAID controller supporting RAID 0/1/5/10.
44.
Position
Function
Color
SATA1
SATA3.0
white
SATA2
SATA3.0
white
SATA3
SATA2.0
black
SATA4
SATA2.0
Black
(NC)
CFAST (option):
(CFAST Card socket), it is located at the bottom of the board and serves as an insert
interface for CFAST card.
45.
SIM (option):
(SIM Socket 7Pin), Support SIM Card devices.
ACS-2695 User Manual
39
46.
M_SATA1(option):
(50.95mmx30mm Socket 52Pin), mSATA socket, it is located at the top, it supports mini
PCI-e devices with LPC bus, B2 mSATA bus for flash disk signal.
47.
H3/H4 (option):
M_SATA1 SCREW HOLES.
H3 and H4 for mini MSATA card (50.95mmx30mm Socket 52 Pin) assemble.
48.
HS1/HS2/HS3/HS4(CPU SCREW HOLES):
CPU FAN SCREW HOLES, Four screw holes for fixed CPU Cooler assemble.
49.
H5/H6:
U4 SCREW HOLES.
50.
TB-522:
ASB-M8671 I/O Card, via a dedicated cable connected to ASB-M8671
MIO1.
LED2:
CF Card LED status.
ACS-2695 User Manual
40
S1:
PWR BT: POWER on/off Button, They are used to connect power switch button. The
two pins are disconnected under normal condition. You may short them temporarily to
realize system startup & shutdown or awaken the system from sleep state.
PWR LED: POWER LED status.
COM3:
(Type DB9),I/O serial port, it provides selectable RS422/RS485 serial signal
output.
RS422 Type (option)
RS485 Type (option)
Signal Name
Pin#
Pin#
Signal Name
422_RX+
1
1
NC
422_RX-
2
2
NC
422_TX-
3
3
485-
422_TX+
4
4
485+
Ground
5
5
Ground
NC
6
6
NC
NC
7
7
NC
NC
8
8
NC
NC
9
9
NC
Note:
Use COM3 RS422 or RS485 Function, please enter BIOS CMOS Setup. Path:
BIOS Setup Utility \ Advanced /Super IO Configuration \ Serial Port3 Type:
[RS-485]
[RS-422]
COM4:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a
direct connection to serial devices.
ACS-2695 User Manual
41
Pin#
Signal Name
1
DCD#
(Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
RI (Ring Indicator)
USB10,USB11:
(Double stack USB type A), I/O USB connector, it provides up to 2 USB2.0 ports,
speed up to 480Mb/s.
Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A.
If the external USB device current exceeds 1.5A, please separate connectors
into different Receptacle.
CF:
(CF Card socket), it is located at TB-522 and serves as an insert interface for Type I
and Type II Compact Flash card. The operating voltage of CF card can be set as 3.3V
or 5V. The default setting of the product is 5V.
MIO1:
(DF13-40P) TB-522 MIO1 via a dedicated cable connected to ASB-M801 MIO1.
ACS-2695 User Manual
42
Signal Name
51.
Pin#
Signal Name
422_RX+
1
2
485+_422TX+
422_RX-
3
4
485-_422TX-
Ground
5
6
NC
NC
7
8
NC
NC
9
10
5V_S5
DCD4-
11
12
RXD4
TXD4
13
14
DTR4-
Ground
15
16
DSR4-
RTS4-
17
18
CTS4-
RI4-
19
20
5V_S5
5V_USB9
21
22
5V_USB1011
USB9_N
23
24
USB10_N
USB9_P
25
26
USB10_P
Ground
27
28
Ground
Ground
29
30
Ground
5V_USB1011
31
32
PWR_LED+
USB11_N
33
34
PWR_LED-
USB11_P
35
36
PS_ON-
Ground
37
38
Ground
Ground
39
40
Ground
TB-523:
ASB-M8671 I/O Card, via a dedicated cable connected to ASB-M8671 MIO1 and
MIO2.
TB-523 Top:
ACS-2695 User Manual
43
TB-523 Bottom:
LED2:
CF Card LED status.
S1:
PWR BT: POWER on/off Button, They are used to connect power switch button. The
two pins are disconnected under normal condition. You may short them temporarily to
realize system startup & shutdown or awaken the system from sleep state.
PWR LED: POWER LED status.
COM3:
(Type DB9),I/O serial port, it provides selectable RS422/RS485 serial signal
output.
RS422 Type (option)
ACS-2695 User Manual
RS485 Type (option)
Signal Name
Pin#
Pin#
Signal Name
422_RX+
1
1
NC
422_RX-
2
2
NC
422_TX-
3
3
485-
422_TX+
4
4
485+
Ground
5
5
Ground
NC
6
6
NC
NC
7
7
NC
NC
8
8
NC
NC
9
9
NC
44
Note:
Use COM3 RS422 or RS485 Function, please enter BIOS CMOS Setup. Path:
BIOS Setup Utility \ Advanced /Super IO Configuration \ Serial Port3 Type:
[RS-485]
[RS-422]
JP4:
(2.0mm Pitch 2x10 Pin Header) COM4 function setting jumper.
Function
JP4 Pin#
RS232
Close: 3-5,4-6,10-12,11-13
(Default)
RS422
Close: 1-3,2-4,5-7,8-10,9-11,12-14,18-20
(option)
RS485
Close: 5-7,8-10,9-11,12-14,16-18
(option)
COM4:
(Type DB9), I/O serial port, it provides selectable RS232/RS422/RS485 serial
signal output.
COM4 RS232 Type (Default):
Pin#
ACS-2695 User Manual
Signal Name
1
DCD# (Data Carrier Detect)
2
RXD (Received Data)
3
TXD (Transmit Data)
4
DTR (Data Terminal Ready)
5
Ground
6
DSR (Data Set Ready)
7
RTS (Request To Send)
8
CTS (Clear To Send)
9
RI (Ring Indicator)
COM4 RS422 Type
(option)
COM4 RS485 Type (option)
Signal Name
Pin#
Pin#
Signal Name
45
422_RX+
1
1
NC
422_RX-
2
2
NC
422_TX-
3
3
485-
422_TX+
4
4
485+
Ground
5
5
Ground
NC
6
6
NC
NC
7
7
NC
NC
8
8
NC
NC
9
9
NC
USB10:
(Single stack USB type A), I/O USB connector, it provides one USB2.0 port, speed up
to 480Mb/s.
USB11:
(2.0mm Pitch 1x4 box Pin Header), I/O USB connector, it provides one USB2.0 port,
speed up to 480Mb/s.
Pin#
Signal Name
1
5V_USB1011
2
USB11_N
3
USB11_P
4
Ground
USB10 and USB11 current limited value is 1.5A.
If the external USB device current exceeds 1.5A, please separate connectors
into different Receptacle.
CF:
(CF Card socket), it is located at TB-523 and serves as an insert interface for Type I
and Type II Compact Flash card. The operating voltage of CF card can be set as 3.3V
or 5V. The default setting of the product is 5V.
ACS-2695 User Manual
46
GPIO:
(3.5mm Pitch 2x5 Pin Connector),General-purpose input/output port, it provides a group
of self-programming interfaces to customers for flexible use.
Function
+5V
Pin#
Function
1
2
Ground
GPIO_IN1
3
4
GPIO_IN2
GPIO_IN3
5
6
GPIO_IN4
GPIO_OUT1
7
8
GPIO_OUT2
GPIO_OUT3
9
10
GPIO_OUT4
MIO1:
(DF13-40P) TB-523 MIO1 via a dedicated Y cable connected to ASB-M801 MIO1 and
MIO2.
Signal Name
ACS-2695 User Manual
Pin#
Signal Name
422_RX+
1
2
485+_422TX+
422_RX-
3
4
485-_422TX-
Ground
5
6
GPIO_IN1
GPIO_IN2
7
8
GPIO_IN3
GPIO_IN4
9
10 5V_S5
DCD4-
11
12 RXD4
TXD4
13
14 DTR4-
Ground
15
16 DSR4-
RTS4-
17
18 CTS4-
RI4-
19
20 5V_S5
5V_USB9
21
22 5V_USB1011
USB9_N
23
24 USB11_N
USB9_P
25
26 USB11_P
Ground
27
28 Ground
47
52.
GPIO_OUT1
29
30 GPIO_OUT2
5V_USB1011
31
32 SO_POWER_SENS
E
USB10_N
33
34 PWR_LED-
USB10_P
35
36 PS_ON-
Ground
37
38 Ground
GPIO_OUT3
39
40 GPIO_OUT4
TB-525E11:
TB-525E11 connect to ASB-M8671T PCIE1X connector, PCIE1X is located at the
top,It provides one PCIE X1 slot.
ACS-2695 User Manual
48
53.
TB-525E12:
TB-525E12 connect to ASB-M8671T PCIE1X connector, PCIE1X is located at the
top,It provides two PCIE X1 slot.
54.
TB-525E161:
TB-525E161 connect to ASB-M8671T PCIE_16X connector, PCIE_16X is located at
the top,It provides one PCIE X16 slot.
ACS-2695 User Manual
49
55.
TB-525P1:
TB-525P1 connect to ASB-M8671T PCIE1X connector, PCIE1X is located at the top,It
provides one PCI slot.
56.
TB-525P1E161:
TB-525P1E161 connect to ASB-M8671T PCIE_16X and PCIE1X connector,
PCIE_16X and PCIE1X is located at the top,It provides one PCIE X16 and one PCI
slot.
ACS-2695 User Manual
50
57.
TB-526E11:
TB-526E11 connect to ASB-M8671B PCIE1X connector, PCIE1X is located at the
Bottom, It provides one PCIE X1 slot.
58.
TB-526E12:
TB-526E12 connect to ASB-M8671B PCIE1X connector, PCIE1X is located at the
Bottom, It provides two PCIE X1 slot.
ACS-2695 User Manual
51
59.
TB-526E161:
TB-526E161 connect to ASB-M8671B PCIE_16X connector, PCIE_16X is located at
the Bottom,It provides one PCIE X16 slot.
60.
TB-526P1:
TB-526P1 connect to ASB-M8671B PCIE1X connector, PCIE1X is located at the
Bottom, It provides one PCI slot.
ACS-2695 User Manual
52
61.
TB-526P1E161:
TB-526P1E161 connect to ASB-M8671B PCIE_16X and PCIE1X connector,
PCIE_16X and PCIE1X is located at the bottom,It provides one PCIE X16 and one
PCI slot.
62.
TB-526P2E161:
TB-526P2E161 connect to ASB-M8671B PCIE_16X and PCIE1X connector,
PCIE_16X and PCIE1X is located at the bottom,It provides one PCIE X16 and two PCI
slot.
ACS-2695 User Manual
53
63.
TB-526P1E82:
TB-526P1E82 connect to ASB-M8671B PCIE_16X and PCIE1X connector, PCIE_16X
and PCIE1X is located at the bottom,It provides two PCIE X8 and one PCI slot.
ACS-2695 User Manual
54
Chapter 3
BIOS Setup
BIOS Setup Description
3.1 Operations after POST Screen
After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS
Setup.
Version 2.10.1208. Copyright (C) 2010 American Megatrends, Inc.
( M8671V15 )
Press 〈DEL〉or〈F2〉to enter setup
CMOS Checksum fail。Press <DEL> to enter setup。
A3
After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is
as follows and includes basic information on BIOS, CPU, memory, and storage devices.
Press F11 to load default values and continue
0085
3.2 BIOS SETUP UTILITY
Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu
containing system summary information will appear.
ACS-2695 User Manual
55
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Main
Advanced
Chipset
BIOS Information
BIOS Vendor
Core Version
Compliancy
Project Version
Build Date and Time
System Language
Boot
Security
Save & Exit
Choose the system
American Megatrends
4.6.4.0
UEFI 2.1
M8671V15 X64
09/21/2012 01:44:36
[English]
Default language
→←: Select Screen
System Date
[Tue 08/21/2012]
↑↓
System Time
[00:00:08]
Enter:
: Select Item
Select
+/- : Charge Opt.
Access Level
Administrator
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC
Exit
Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
3.3 Main Settings
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Main
Advanced
Chipset
BIOS Information
BIOS Vendor
Core Version
Compliancy
Project Version
Build Date and Time
System Language
ACS-2695 User Manual
Boot
Security
Save & Exit
Choose the system
American Megatrends
4.6.4.0
UEFI 2.1
M8671V15 X64
09/21/2012 01:44:36
[English]
Default language
56
→←: Select Screen
System Date
System Time
↑↓
[Tue 07/10/2012]
[00:00:08]
: Select Item
Enter:
Select
+/- : Charge Opt.
Access Level
Administrator
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC
Exit
Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
System Time:
Set the system time, the time format is:
Hour :
Minute :
0 to 23
0 to 59
Second : 0 to 59
System Date:
Set the system date, the date format is:
Day:
Month:
Date:
Year:
3.4
Note that the ‘Day’ automatically changes when you set the date.
01 to 12
01 to 31
1998 to 2099
Advanced Settings
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Main
Advanced
Chipset
Legacy OpROM Support
Launch Storage OpROM
Launch Storage OpROM
Boot
Security
Save & Exit
Enable or Disable Boot
[Disabled]
[Enabled]
Option for Legacy
Network Devices.
►PCI Subsystem Settings
►ACPI Settings
►CPU Configuration
►SATA Configuration
►Thermal Configuration
►PCH-FW Configuration
ACS-2695 User Manual
57
►USB Configuration
►W83627UHG Super IO Configuration
► HW Monitor
→←: Select Screen
►Sandybridge PPM Configuration
+/- : Charge Opt.
↑↓
: Select Item
Enter:
Select
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC
Exit
Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
3.4.1 PCI Subsystem Settings
PCI Bus Driver Versio V2.03.00
PCI ROM Priority:
[EFI Compatible ROM]
[Legacy ROM]
PCI Common Settings:
PCI Latency Timer:
[32 PCI Bus Clocks]
[64 PCI Bus Clocks]
[96 PCI Bus Clocks]
[128 PCI Bus Clocks]
[160 PCI Bus Clocks]
[192 PCI Bus Clocks]
[224 PCI Bus Clocks]
[248 PCI Bus Clocks]
PCI Express Device Settings:
Relaxed Ordering:
[Disabled]
[Enabled]
Extended Tag:
[Disabled]
[Enabled]
No Snoop:
[Enabled]
[Disabled]
Maximum Payload:
[Auto]
[128 Bytes]
ACS-2695 User Manual
58
[256 Bytes]
[512 Bytes]
[1024 Bytes]
[2048 Bytes]
[4096 Bytes]
Maximum Read Request:
[Auto]
[128 Bytes]
[256 Bytes]
[512 Bytes]
[1024 Bytes]
[2048 Bytes]
[4096 Bytes]
PCI Express Link Settings:
ASPM Support:
[Disabled]
[Enabled]
WARNING:Ebabling ASPM may cause some
PCI-E devices to fail
Extended Synch:
[Disabled]
[Enabled]
3.4.2
ACPI Settings
Enable ACPI Auto Configuration:
[Disabled]
[Enabled]
Enable Hibernation:
[Enabled]
[Disabled]
ACPI Sleep State:
[S3 (Suspend to RAM)]
[Suspend Disabled]
[S3 (Suspend to RAM)]
Lock Legacy Resources:
[Disabled]
[Enabled]
ACS-2695 User Manual
59
3.4.3
CPU Configuration
Socket 0 CPU Information:
Intel(R) Core(TM) i5-2430M CPU @2.40GHz
CPU Signature
Microcode Patch
Max CPU Speed
Min CPU Speed
Processor Cores
Intel HT Technology
Intel VT-x Technology
L1 Data Cache
L1 Code Cache
L2 Cache
L3 Cache
CPU Speed
64-bit
206a7
25
2400 MHz
800 Mhz
2
Supported
Supported
32 KB x 2
32 KB x 2
256 KB x 2
3072 KB
2400 MHz
Supported
Hyper-Threading:
[Enabled]
[Disabled]
Active Processor Cores
[All]
[1]
Limit CPUID Maximum:
[Enabled]
[Disabled]
Execute Disable Bit:
[Enabled]
[Disabled]
Hardware Prefetcher
[Enabled]
[Disabled]
Adjacent Cache Line Prefetch
[Enabled]
[Disabled]
ACS-2695 User Manual
60
Intel Virtualization Technology
[Enabled]
[Disabled]
3.4.4
SATA Configuration
SATA Controller(S):
[Enabled]
[Disabled]
SATA Mode Selection:
[IDE]
[AHCI]
[RAID]
SATA Test Mode:
[Disabled]
[Enabled]
ISRT Support
[Enabled]
[Disabled]
Delay of the OROM UI Splash Screen
[2 SEC]
[4 SEC]
[6 SEC]
[8 SEC]
ACS-2695 User Manual
Serial ATA Port 0
Software Preserve
Empty
Unknown
Serial ATA Port 1
Software Preserve
Empty
Unknown
Serial ATA Port 2
Software Preserve
Empty
Unknown
Serial ATA Port 3
Empty
Software Preserve
Unknown
Serial ATA Port 4
Software Preserve
Empty
Unknown
Serial ATA Port 5
Empty
61
Software Preserve
3.4.5
Unknown
Thermal Configuration
Platform Thermal Configuration
Critical Trip Point
[POR]
[15 C]
[23 C]
[31 C]
[39 C]
[47 C]
[55 C]
[63 C]
[71 C]
[79 C]
[87 C]
[95 C]
[103 C]
[111 C]
[119 C]
Active Trip Point Hi Fan Speed
[71 C]
[15 C]
[23 C]
[31 C]
[39 C]
[47 C]
[55 C]
[63 C]
[79 C]
[87 C]
[95 C]
[103 C]
[111 C]
[119 C]
Active Trip Point 0 Fan Speed
Active Trip Point Lo Fan Speed
ACS-2695 User Manual
100
[55 C]
[15 C]
[23 C]
[31 C]
[39 C]
62
[47 C]
[63 C]
[71 C]
Active Trip Point 1 Fan Speed
Passive Trip Point
[79 C]
[87 C]
[95 C]
[103 C]
[111 C]
[119 C]
75
[95 C]
[15 C]
[23 C]
[31 C]
[39 C]
[47 C]
[55 C]
[63 C]
[71 C]
[79 C]
[87 C]
[95 C]
[103 C]
[111 C]
[119 C]
Passive TC1 Value
Passive TC2 Value
Passive TSP Value
ME SEBus Thermal Reporting
[Disabled]
[Enabled]
PCH Thermal Device
[Disabled]
[Enabled]
MCH Temp Read
[Disabled]
[Enabled]
PCH Temp Read
[Disabled]
[Enabled]
CPU Energy Read
[Disabled]
[Enabled]
CPU Temp Read
[Disabled]
[Enabled]
Alert Enable Lock
ACS-2695 User Manual
1
5
10
[Disabled]
63
[Enabled]
3.4.6
PCH-FW Configuration
ME FW Version
7.1.52.1176
ME Firmware Mode
Normal Mode
ME Firmware Type
Full Sku Firmware
ME Firmware SKU
Unidentified
Firmware Update Configuration
ME FW Image Re-Flash
[Disabled]
[Enabled]
3.4.7
USB Configuration
USB Configuration
USB Devices:
1 keyboard, 2 Hubs
Legacy USB Support:
[Enabled]
[Disabled]
EHCI Hand-off:
[Disabled]
[Enabled]
Port 60/64 Emulation
[Enabled]
[Disabled]
USB hardware delays and time-outs:
USB transfer time-out:
[20 sec]
[10 sec]
[5 sec]
[1 sec]
Device reset time-out:
[20 sec]
[10 sec]
[30 sec]
[40 sec]
Device power-up delay
[Auto]
[Manual]
ACS-2695 User Manual
64
3.4.8
W83627UHG Super IO Configuration
W83627UHG Super IO Configuration
Super IO Chip
Winbond W83627UHG
COM1 Configuration
COM2 Configuration
COM3 Configuration
COM4 Configuration
COM5 Configuration
COM6 Configuration
3.4.9
3.4.10
HW Monitor
PC Health Status
System temperature
:
CPU temperature
CPU Fan Speed
VCORE
: +56
: 7000 RPM
: +1.145V
+12V
+3.3V
+1.5V
5VSB
VBAT
:
:
:
:
:
+42 C
+11.556 V
+3.280 V
+1.520 V
+5.125 V
+3.136 V
Sandybridge PPM Configuration
Sandybridge PPM Configuration
EIST
[Enabled]
[Disabled]
Turbo Mode
[Enabled]
[Disabled]
CPU C3 Report
[Enabled]
[Disabled]
CPU C6 report
[Enabled]
[Disabled]
CPU C7 report
[Enabled]
[Disabled]
ACS-2695 User Manual
65
Long duration power limit
Long duration maintained
Short duration power limit
0
28
0
TCC active offset
3.5
0
Chipset Settings
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Save & Exit
System Agent (SA)
►System Agent (SA) Configuration
►PCH-IO Configuration
Parameters
→←: Select Screen
↑↓
: Select Item
Enter:
Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC
Exit
Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
3.5.1 ► System Agent (SA) Configuration
►PCH-IO Configuration
System Agent (SA) Configuration
System Agent RC Version
VT-d Capability
2.7.0.0
Unsupported
►Graphics Configuration
IGFX VBIOS Version
ACS-2695 User Manual
2120
66
IGFX Frequency
Graphics Turbo IMON Current
Primary Display
650 MHz
31
[Auto]
[IGFX]
[PEG]
[PCI]
Internal Graphics
[Auto]
[Disabled]
[Enabled]
GTT Size
[2MB]
[1MB]
Aperture Size
[256MB]
[128MB]
[512MB]
DVMT Pre-allocated
[64MB]
[0MB]
[32MB]
[96MB]
[128MB]
[160MB]
[192MB]
[224MB]
[256MB]
[288MB]
[320MB]
[352MB]
[384MB]
[416MB]
[448MB]
[480MB]
[512MB]
Dvmt Total Gfx Mem
[256MB]
[128MB]
[MAX]
GFX Low Power Mode
ACS-2695 User Manual
67
[Enabled]
[Disabled]
LCD Control:
Primary IGFX Boot Display
[VBIOS Default]
[CRT]
[DVI]
[LVDS]
LCD Panel Type
[1280 X 1024 24bit 2ch]
[640 X 480 18bit 1ch]
[800 X 480 18bit 1ch]
[800 X 600 18bit 1ch]
[800 X 600 24bit 1ch]
[1024 X 768 18bit 1ch]
[1024 X 768 24bit 1ch]
[1280 X 800 18bit 1ch]
[1366 X 768 18bit 1ch]
[1440 X 900 24bit 2ch]
[1600 X 900 24bit 2ch]
[1600 X 1200 24bit 2ch]
[1680 X 1050 24bit 2ch]
[16800 X 1050 24bit 2ch]
[1920 X 1080 24bit 2ch]
[2048 X 1536 24bit 2ch]
Panel Scaling
[Auto ]
[Off ]
[Force Scaling ]
Backlight Control
[DC ]
[PWM]
Backlight Logic
[Positive ]
[Negaive]
Backlight Control Control Level
[Level 8 ]
[Level 0 ]
ACS-2695 User Manual
68
[Level 1 ]
[Level 2 ]
[Level 3 ]
[Level 4 ]
[Level 5 ]
[Level 6 ]
[Level 7 ]
[Level 9 ]
[Level 10 ]
[Level 11 ]
[Level 12 ]
[Level 13]
[Level 14 ]
[Level 15]
[Level 16 ]
BIA
[Auto ]
[Disabled ]
[Level 1 ]
[Level 2 ]
[Level 3 ]
[Level 4 ]
[Level 5 ]
Spread Spectrum clock chip
[Off ]
[Hardware ]
[Software ]
ALS Support
[Disabled]
[Enabled]
Panel Color Depth
[18 Bit]
[24 Bit]
►DMI Configuration
►NB PCIe Configuration
PEG0
PEG0 – Gen X
ACS-2695 User Manual
[Not Present]
[Auto]
69
[Gen1]
[Gen2]
PEG1
PEG1 – Gen X
[Not Present]
[Auto]
[Gen1]
[Gen2]
PEG2
PEG2 – Gen X
[Not Present]
[Auto]
[Gen1]
[Gen2]
PEG3
[Not Present]
PEG3 – Gen X
[Auto]
[Gen1]
[Gen2]
Always Enable PEG
[Enabled]
[Disabled]
PEG ASPM
[Disabled]
[Auto]
[ASPM LOs]
[ASPM L1]
[ASPM LOsL1]
ASPM LOs
[Root Port Only]
[Endpoint Port Only]
[Both Root and Endpoint Ports]
De-emphasis Control
[-3.5 dB]
[-6 dB]
►Memory Configuration
Memory RC Version
Memory Frequency
ACS-2695 User Manual
1.2.2.0
1333 Mhz
70
Total Memory
DIMM#0
DIMM#1
2048 MB (DDR3)
2048 MB (DDR3)
Not Present
DIMM#2
DIMM#3
CAS Latency (tCL)
Minimum delay time
CAS to RAS (tRPmin)
Row Precharge (tRPmin)
Active to Precharge (tRPmin)
DIMM profile
Not Present
Not Present
7
7
7
20
[Default DIMM profile]
[XMP profile 1]
[XMP profile 2]
Memory Frofile
[Auto]
[1067]
[1333]
[1600]
[1867]
[2133]
Max TOLUD
[Dynamic]
[1GB]
[1.25GB]
[1.5GB]
[1.75GB]
[2GB]
[2.25GB]
[2.5GB]
[2.75GB]
[3GB]
[3.25GB]
NMode Support
[Auto]
[1N Mode]
[2N Mode]
Memory Scrambler
[Enabled]
[Disabled]
ACS-2695 User Manual
71
RMT Crosser Support
Memory Scrambler
[Disabled]
[Enabled]
MRC Fast Boot
[Enabled]
[Disabled]
Force Cold Reset
[Enabled]
[Disabled]
Scrambler Seed Generation off
[Disabled]
[Enabled]
Memory Remap
[Disabled]
[Enabled]
Channel A DIMM Control
[Enabled Both DIMMS]
[Disabled DIMM0]
[Disabled DIMM1]
[Disabled Both DIMMS]
►GT-Power Management Control
GT Info
RC6 (Render Standby)
GT2 (0X116)
[Enabled]
[Disabled]
GT overClocking Support
[Disabled]
[Enabled]
►PCH-IO Configuration
Intel PCH RC Version
Intel PCH SKU Name
Intel PCH Rev ID
1.2.1.0
QM67
05/B3
PCH LAN Controller
[Disabled]
[Enabled]
Board Capability
[SUS_PWR_DN_ACK]
[Deepsx]
ACS-2695 User Manual
72
EC Turbo Control Mode
[Disabled]
[Enabled]
Azalia
[Auto]
[Disabled]
[Enabled]
Azalia Internal Codec
[Enabled]
[Disabled]
BIOS Security Configuration
High Precision Event Timer Configuration
High Precision Timer
[Enabled]
[Disabled]
SLP_S4 Assertion Width
[4-5 Seconds]
[1-2 Seconds]
[2-3 Seconds]
[3-4 Seconds]
Restore AC Power Loss
[Last State]
[Power off]
[Power on]
Set NAND Management Override
[Enabled]
[Disabled]
►USB Configuration
EHCI1
[Enabled]
[Disabled]
EHCI2
[Enabled]
[Disabled]
USB Ports Per-Port Disable Control
[Disabled]
[Enabled]
►PCI Express Configuration
PCI Express Clock Gating
ACS-2695 User Manual
73
[Enabled]
[Disabled]
DMI Link ASPM Control
[LOSL1]
[LOS]
[Disabled]
DMI Link Extended Synch Control
[Disabled]
[Enabled]
Subtractive Decode
[Disabled]
[Enabled]
►PCI Express Root Port 1
►PCI Express Root Port 2
►PCI Express Root Port 3
►PCI Express Root Port 4
►PCI Express Root Port 5
►PCI Express Root Port 6
►PCI Express Root Port 7
►PCI Express Root Port 8
ACS-2695 User Manual
74
3.6 Boot Settings
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Boot Configuration
Setup Prompt Timeout
Bootup Numlock State
Security
Save & Exit
Number of seconds to
1
[On]
Wait for setup
Activation key.
65535(0xFFFF)means
Fast Boot
[Enabled]
CSM16 Module Version
Indef inite waiting.
07.64
Gatea20 Active
Option ROM Messages
Interrupt 19 Capture
[Upon Request]
[Force BIOS]
[Enabled]
→←: Select Screen
↑↓
Boot Option Priorities
Boot Option #1
Hitachi…]
Hard Drive BBS Priorities
: Select Item
Enter:
[SATA PM:
Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC
Exit
Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
Setup Prompt Timeout
Bootup Numlock State
[1]
[On]
[off]
Quiet Boot
[Disabled]
[Enabled]
CSM16 Module Verison
Gatea20 Active
07.64
[Upon Request]
[Always]
ACS-2695 User Manual
75
Option ROM Messages
[Force BIOS]
[Keep Current]
Interrupt 19 Capture
[Disabled]
[Enabled]
Boot Override
SATA PM: ST9320423AS
……
Launch EFI Shell from filesystem device
3.7 Security Settings
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Main
Advanced
Chipset
Boot
Security
Password Description
Save & Exit
Set Administrator
Password
If ONLY the Administrator’s password is set,
Then this only limits access to Setup and is
Only asked for when entering Setup.
If ONLY the User’s password is set, then this
Is a power on password and must be entered to
Is a power on password and must be entered to
Boot or enter Setup. In Setup the User will
Have Administrator rights.
The password length must be 3 to 20 Characters
long.
→←: Select Screen
↑↓
: Select Item
Enter:
Select
+/- : Charge Opt.
Administrator Password
User Password
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC
Exit
Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
3.7.1
ACS-2695 User Manual
Administrator Password
76
3.7.2
User Password
Type the password with up to 20 characters and then press Enter key. This will
clear all previously typed CMOS passwords. You will be requested to confirm the
password. Type the password again and press Enter key. You may press Esc
key to abandon password entry operation.
To clear the password, just press Enter key when password input window pops up.
A confirmation message will be shown on the screen as to whether the password will
be disabled. You will have direct access to BIOS setup without typing any password
after system reboot once the password is disabled.
Once the password feature is used, you will be requested to type the password each
time you enter BIOS setup. This will prevent unauthorized persons from changing
your system configurations.
Also, the feature is capable of requesting users to enter the password prior to system
boot to control unauthorized access to your computer. Users may enable the feature
in Security Option of Advanced BIOS Features. If Security Option is set to System,
you will be requested to enter the password before system boot and when entering
BIOS setup; if Security Option is set to Setup, you will be requested for password for
entering BIOS setup.
3.8 Save & Exit Settings
Aptio Setup Utility – Copyright (C) 2010 American Megatrends, Inc.
Main
Advanced
Chipset
Save Changes and Exit
Discard Changes and Exit
Save Changes and Reset
Discard Changes and Reset
Boot
Security
Save & Exit
Exit system setup after
Saving the changes.
Save Options
Save Changes
Discard Changes
ACS-2695 User Manual
77
→←: Select Screen
Restore Defaults
Save user Defaults
Restore user Defaults
↑↓
: Select Item
Enter:
Select
+/- : Charge Opt.
Boot Override
SATA PM:*** …
Launch EFI Shell from filesystem device
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC
Exit
Version 2.10.1208. Copyright (C) 2010 American Megatrends , Inc.
Save Changes and Exit
Save & Exit Setup save Configuration and exit ?
[Yes]
[No]
Discard Changes and Ext
Exit Without Saving Quit without saving?
[Yes]
[No]
Save Changes and Reset
Save & reset Save Configuration and reset?
[Yes]
[No]
Discard Changes and Reset
Reset Without Saving Reset without saving?
[Yes]
[No]
Save Changes
Save Setup Values Save configuration?
[Yes]
[No]
Discard Changes
Load Previous Values Load Previous Values?
[Yes]
[No]
Restore Defaults
Load Optimized Defaults Load optimized Defaults?
[Yes]
[No]
Save user Defaults
Save Values as User Defaults Save configuration?
ACS-2695 User Manual
78
[Yes]
[No]
Restore user Defaults
Restore User Defaults Restore User Defaults?
[Yes]
[No]
Launch EFI Shell from filesystem device
WARNING Not Found
[ok]
--------------------------------------------------------------------------------------------------------------------
ACS-2695 User Manual
79
Chapter 4
Installation of Drivers
This chapter describes the installation procedures for software and drivers under the windows XP. The
software and drivers are included with the motherboard. The contents include Intel chipset driver,
VGA driver, LAN driver, Audio driver, .NET framework 3.5 driver
Installation instructions are given below.
Important Note:
After installing your Windows operating system (Windows XP), you must install
first the Intel Chipset Software Installation Utility before proceeding with the
installation of drivers.
I
ACS-2695 User Manual
80
4.1 Intel Chipset Driver
To install the Intel chipset driver, please follow the steps below.
Step 1: Select Chipset from the list
Follow the step-by-step installation process to install the driver.
ACS-2695 User Manual
81
ACS-2695 User Manual
82
ACS-2695 User Manual
83
Click Finish, when the installation process is complete, the Setup Complete screen appears. See as
picture.
4.2 Intel VGA Chipset Driver
To install the VGA drivers, follow the steps below to proceed with the installation.
1. Click Intel VGA Chipset Driver.
ACS-2695 User Manual
84
Follow the step-by-step installation process to install the Graphics Media Accelerator driver.
ACS-2695 User Manual
85
ACS-2695 User Manual
86
ACS-2695 User Manual
87
ACS-2695 User Manual
88
Click FINISH; A Driver Installation Complete.
ACS-2695 User Manual
89
4.3 Intel 82574L Network adapter Driver
To install the Intel 82574L Network adapter Driver, please follow the steps below.
Select LAN from the list
Follow the step-by-step installation process to install the LAN driver.
ACS-2695 User Manual
90
ACS-2695 User Manual
91
ACS-2695 User Manual
92
Click FINISH; A Driver Installation Complete.
4.4 Realtek HD Audio Driver Installation
To install the Realtek High Definition (HD) Audio driver, please follow the steps below.
Select Audio from the list
ACS-2695 User Manual
93
Follow the step-by-step installation process to install the Realtek HD Audio driver.
ACS-2695 User Manual
94
Click FINISH; A Driver Installation Complete.
4.5 Microsoft .NET Framework 3.5 Service Installation
To install the Microsoft .NET Framework 3.5 Service, please follow the steps below.
ACS-2695 User Manual
95
ACS-2695 User Manual
96
ACS-2695 User Manual
97