Siemens OpenStage 15 User guide

Documentation
OpenScape Voice
OpenStage15 SIP
User Guide
Communication for the open minded
V1 R3.x
V1 R4.x
Siemens Enterprise Communications
www.siemens-enterprise.com
Important information
Important information
For safety reasons, the telephone should only be supplied with power:
• using the original power supply unit.
Part number: L30250-F600-C14x (x: 1=EU, 2=US,
3=UK) or
• in a LAN with PoE (Power over Ethernet), which
complies with the IEEE 802.3af standard.
Q
Never open the telephone or a key module. Should you
encounter any problems, contact the responsible service personnel.
Use only original Siemens accessories. The use of other accessories may be hazardous and will render the
warranty, extended manufacturer’s liability and the CE
marking invalid.
Trademarks
The device conforms to the EU directive 1999/5/EC as attested by the CE marking.
All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
Proper disposal and separate collection of your old appliance will help prevent potential damage to the environment
and human health. It is a prerequisite for reuse and recycling
of used electrical and electronic equipment.
For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service, the shop where you purchased the product or your
sales representative.
The statements quoted above are only fully valid for equipment which is installed and sold in the countries of the European Union and is covered by the directive 2002/96/EC.
Countries outside the European Union may impose other
regulations regarding the disposal of electrical and electronic equipment.
2
Important information
Location of the telephone
•
•
•
•
•
The telephone should be operated in a controlled environment with an
ambient temperature between 5°C and 40°C.
To ensure good speakerphone quality, the area in front of the microphone (front right) should be kept clear. The optimum speakerphone
distance is 50 cm.
Do not install the telephone in a room where large quantities of dust
accumulate; this can considerably reduce the service life of the telephone.
Do not expose the telephone to direct sunlight or any other source of
heat, as this is liable to damage the electronic components and the
plastic casing.
Do not operate the telephone in damp environments such as bathrooms.
Product support on the internet
Information and support for our products can be found on the Internet at:
http://www.siemens-enterprise.com/.
Technical notes, current information about firmware updates, frequently
asked questions and lots more can be found on the Internet at:
http://wiki.siemens-enterprise.com/.
3
Contents
Important information . . . . . . . . . . . . . . . . . . . . . . . . . .2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Location of the telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product support on the internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General information. . . . . . . . . . . . . . . . . . . . . . . . . . .11
About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols used in the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephone type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speakerphone quality and display legibility . . . . . . . . . . . . . . . . . . . . . .
Single-line telephone/multi-line telephone. . . . . . . . . . . . . . . . . . . . . . .
11
11
12
12
12
12
13
Getting to know your OpenStage phone . . . . . . . . .14
The user interface of your OpenStage 15 . . . . . . . . . . . . . . . . . . . . . . .
Ports on the underside of the phone. . . . . . . . . . . . . . . . . . . . . . . . . . .
Using network ports more efficiently . . . . . . . . . . . . . . . . . . . . . . .
OpenStage Key Module 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mailbox key and Menu key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigation keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunk keys (on multi-line phones only). . . . . . . . . . . . . . . . . . . . . . .
Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Context-dependent displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program/Service menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control and monitoring function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
14
15
16
17
18
18
18
18
19
20
22
24
24
26
28
28
28
29
29
30
31
Basic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Secure voice transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call via the handset . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call via the loudspeaker (speakerphone mode) . . . . . .
Directed pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accept call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Picking up the held call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching from handset to speakerphone mode . . . . . . . . . . . . . . . . .
Switching from speakerphone mode to the handset . . . . . . . . . . . . . .
Open listening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating the microphone . . . . . . . . . . . . . . . . . . . . . . . .
Ending a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Group call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Listening to voicemail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Two calls simultaneously . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
While dialling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Off-hook dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-hook dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Immediate dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing using the hot or warm line function . . . . . . . . . . . . . . . . . . .
Redial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consulting a second party . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ending a consultation call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching to the held party (alternating) . . . . . . . . . . . . . . . . . . . . .
Putting on hold and retrieving successively or simultaneously . . . .
Connecting parties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activate or deactivate immediate forwarding . . . . . . . . . . . . . . . . .
Saving destination phone numbers for call forwarding . . . . . . . . . .
Activate/deactivate call forwarding . . . . . . . . . . . . . . . . . . . . . . . . .
Call forwarding chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requesting callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Responding to a callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Allow callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling back missed calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
32
33
33
34
34
35
36
37
37
38
38
39
42
43
43
43
45
45
46
47
48
49
50
51
51
52
53
54
55
56
58
61
62
62
63
64
65
5
Programmable keys. . . . . . . . . . . . . . . . . . . . . . . . . . .66
List of available functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming a key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beginning programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Beginning programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming enhanced functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repertory dial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature toggle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring a fixed forwarding key . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring a variable call forwarding key . . . . . . . . . . . . . . . . . . . .
Using programmed keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example 1: Calling saved number . . . . . . . . . . . . . . . . . . . . . . . . . .
Example 2: Call Waiting toggle Activating/deactivating . . . . . . . . . .
Example 3: Immediate ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting programmable keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
67
67
68
68
68
70
71
72
73
73
73
73
74
Enhanced phone functions. . . . . . . . . . . . . . . . . . . . .75
Incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Deflecting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Rejecting a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Configuring call forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Placing a call on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Call waiting (second call) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Transferring a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
CTI calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Making calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Dialing with the DDS key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Dialing a phone number from a list . . . . . . . . . . . . . . . . . . . . . . . . . 93
Using autodial delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Local conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
System-based conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Call lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Dial entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Delete all entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
6
Making calls with multiple lines . . . . . . . . . . . . . . 103
Incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accepting calls for the primary line . . . . . . . . . . . . . . . . . . . . . . . .
Accepting calls for secondary lines . . . . . . . . . . . . . . . . . . . . . . . .
Making calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual trunk seizure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic trunk seizure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing the last dialed number . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forwarding calls for primary line . . . . . . . . . . . . . . . . . . . . . . . . . .
During calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making and receiving calls on a single line . . . . . . . . . . . . . . . . . .
Making and receiving calls with multiple lines. . . . . . . . . . . . . . . .
Putting a line on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lines with hot or warm line function . . . . . . . . . . . . . . . . . . . . . . .
Busy override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Direct station selection keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling a station directly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deflecting a call to a DSS station . . . . . . . . . . . . . . . . . . . . . . . . .
LED display on DSS keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making calls in an executive-secretary team . . . . . . . . . . . . . . . . . . . .
Sample scenarios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accepting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSS keys can be used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings for MultiLine (keyset) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the time for a delayed ringer . . . . . . . . . . . . . . . . . . . . . . .
Line preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rollover for a line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
103
103
103
104
104
104
105
105
106
106
106
107
108
109
110
110
111
112
112
113
113
114
115
116
117
117
118
119
Privacy/security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Deactivating the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Do not disturb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling do not disturb via a key . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling do not disturb via the idle menu . . . . . . . . . . . . . . . . . . .
Allowing "Do not disturb" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phone locking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
120
121
121
121
122
123
123
126
7
Mobility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Mobility scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging on and off at the same phone . . . . . . . . . . . . . . . . . . . . .
Logging on and off at different phones . . . . . . . . . . . . . . . . . . . . .
Logging on and off at the same phone . . . . . . . . . . . . . . . . . . . . . . . .
Logging on to the phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging off from the phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging on at different telephones . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging on with forced logoff at a remote phone . . . . . . . . . . . . .
Logging on with forced, delayed logoff at a remote- phone . . . . .
128
128
128
129
129
130
131
131
132
OpenScape Voice functions. . . . . . . . . . . . . . . . . . .133
Feature toggle key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making anonymous calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temporarily activating anonymous calling for the next call . . . . . .
Temporarily deactivating anonymous calling for the next call . . . .
Creating a list for selective calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For call acceptance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For call rejection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anonymous calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rejecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accepting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using abbreviated dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call tracing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hunt group functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a line busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Marking the last line in the hunt group chain. . . . . . . . . . . . . . . . .
Reachability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unparking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Silent Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Active silent monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Muted silent monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Code table for OpenScape Voice functions. . . . . . . . . . . . . . . . . . . . .
8
133
134
134
134
135
135
136
136
137
138
138
138
139
139
140
140
141
142
142
143
145
145
145
146
146
147
148
Individual phone configuration . . . . . . . . . . . . . . . 149
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting daylight saving time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic daylight saving time . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time display format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date display format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volumes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tone and indication with an unsecured voice connection . . . . . . .
Key click. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the language and country . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Country-specific settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting user data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initiating the reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
149
149
150
150
150
151
152
152
153
154
154
155
158
159
160
160
162
163
164
164
Call recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
Call recording modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanations of recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recordable calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Non-recordable calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enhanced functions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The following features are not supported:. . . . . . . . . . . . . . . . . . .
Recording tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recording calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the call recording feature . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic call recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual call recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call recording with AutoStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controlling call recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consultation during call recording . . . . . . . . . . . . . . . . . . . . . . . . .
Second call during call recording . . . . . . . . . . . . . . . . . . . . . . . . . .
Call recording while alternating . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your call is paused and reconnected during the recording. . . . . . .
Setting up a conference during recording . . . . . . . . . . . . . . . . . . .
Adding conference participants . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your call is included in a conference during the recording. . . . . . .
Putting a line on hold manually during the recording . . . . . . . . . . .
Diagnostic information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
165
166
166
166
167
167
167
167
167
168
169
169
170
171
171
172
172
173
173
174
174
176
9
Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .178
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling up the Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administrator Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
178
178
178
179
180
Fixing problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . .183
Caring for your telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact partner in the case of problems . . . . . . . . . . . . . . . . . . . . . . .
Labeling keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
183
183
183
184
Local user menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .185
Opening the user menu on the phone . . . . . . . . . . . . . . . . . . . . . . . . 185
User menu display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Key functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .195
10
General information
General information
About this manual
This document contains general descriptions of the technical options,
which may not always be available in individual cases. The respective features must therefore be individually defined in the terms of the contract.
If a particular function on your phone is not available to you, this may be
due to one of the following reasons:
• The function is not configured for you or your telephone. Please contact your system support representative.
• Your communications platform does not feature this function. Please
contact your Siemens sales partner for information on how to upgrade.
This user guide is intended to help you familiarize yourself with OpenStage
and all of its functions. It contains important information on the safe and
proper operation of your OpenStage phone. These instructions should be
strictly complied with to avoid operating errors and ensure optimum use of
your multifunctional telephone in the network.
These instructions should be read and followed by every person installing,
operating or programming an OpenStage phone.
For your own protection, please read the section dealing with safety
in detail. Follow the safety instructions carefully in order to avoid endangering yourself or other persons and to prevent damage to the
unit.
This user guide is designed to be simple and easy to understand, providing
clear step-by-step instructions for operating your OpenStage phone.
Administrative tasks are dealt with in a separate manual. The Quick Reference Guide contains quick and reliable explanations of frequently used
functions.
Symbols used in the manual
Settings
Operations and settings that can be made both at the phone and over the
Web interface are indicated by an icon and page reference.
V
z
is a reference to an operation or setting performed directly on the
phone
is a reference to an operation or setting performed via the Web-interface
11
General information
Call recording
.
~
/
@
Switch on recorder (standby mode)
Switch off recorder
Start recording
Stop recording
Service
The Siemens service department can only help you if you experience problems or defects with the phone.
Should you have any questions regarding operation, your specialist
retailer or network administrator will gladly help you.
For queries regarding connection of the telephone, please contact
your network provider.
If you experience problems or defects with the phone, please dial the service number for your country.
Intended use
The OpenStage phone is a desktop unit designed for voice transmission
and for connection to the LAN. It can also be used as a workstation device.
Any other use is regarded as unauthorized.
Telephone type
The phone name data can be found on the name plate on the base of the
device; The exact product name and serial number are specified here. Specific details concerning your communications platform can be obtained
from your service technician.
Please have this information ready when you contact our service department regarding faults or problems with the product.
Speakerphone quality and display legibility
•
•
12
To ensure good speakerphone quality, the area in front of the telephone
(front right) should be kept clear). The optimum distance is
approx. 50 cm.
Proceed as follows to optimize display legibility:
– Turn the phone to tilt the display to ensure you have a frontal view of
the display while eliminating light reflexes.
– Adjust the contrast as required ! page 149.
General information
Single-line telephone/multi-line telephone
Your OpenStage 15 is a "multi-line telephone". This means that multiple
lines can be configured, which is not the case with single-line phones.
Each line is assigned an individual phone number which you can use to
make and receive calls.
The programmable keys function as line keys on multi-line phones
! page 20.
A number of specific features must be considered when using a multi-line
phone to make and receive calls ! page 106.
13
Getting to know your OpenStage phone
Getting to know your OpenStage phone
The following sections describe the most frequently used operating elements and the displays on your OpenStage phone.
The user interface of your OpenStage 15
1
2
3
4
5
6
14
7
1
You can make and receive calls as normal using the handset.
2
The display provides intuitive support for telephone operation (two
lines with up to 33 characters each).
3
Audio keys are also available, allowing you to optimally configure
the audio features on your telephone ! page 18.
4
O mailbox key and N menu key.
5
The keypad is provided for input of phone numbers/codes.
6
The navigation keys is used to operate the phone ! page 18.
7
The programmable sensor keys can be programmed with functions ! page 66.
Getting to know your OpenStage phone
Ports on the underside of the phone
Power supply unit
(if necessary)
PC
Network switch
Local
cable type
Key module
Handset
Properties of your OpenStage 15
Display type
Full-duplex speakerphone function
10/100 Mbps Ethernet switch ! page 16
Wall mounting
LCD display, 24 x 2 characters
;
;
;
15
Getting to know your OpenStage phone
Using network ports more efficiently
OpenStage 15 has a built-in 10/100 Mbps Ethernet switch. This means that
you can connect a PC to the LAN directly via the phone. The telephone-PC
connection option must first be activated on the telephone by service personnel.
Network switch
OpenStage 15
PC
Using this connection option saves one network port for each switch used
and requires fewer or shorter network cables when arranged correctly.
16
Getting to know your OpenStage phone
OpenStage Key Module 15
The OpenStage Key Module 15 is a key module attached to the side of the
phone that provides an additional 18 illuminated, programmable sensor
keys.
Like keys on the phone, these keys can be programmed and used according to your needs ! page 19.
You can only attach one OpenStage Key Module 15 to your OpenStage 15.
17
Getting to know your OpenStage phone
Keys
Audio keys
Key
Function when key is pressed
- Set the volume lower ! page 154.
n Turn speaker on/off (with red LED key) ! page 37.
+ Set the volume higher ! page 154.
Mailbox key and Menu key
Key
Function when key is pressed
O Open the menu for voicemail or missed calls (with red LED key).
N Open the phone’s main menu (with red LED key).
Navigation keys
These are used to manage most of your phone’s functions and display.
Key
Function when key is pressed
< In lists and menus: Scroll up. Set lighter contrast ! page 149.
input
= •• Confirm
Perform action
:
18
In idle mode: Open the idle menu ! page 24.
In lists and menus: Scroll down. Set darker contrast ! page 149.
Getting to know your OpenStage phone
Programmable function keys
Your OpenStage 15 has eight illuminated keys to which you can assign
functions or numbers.
Increase the number of programmable function keys by connecting
a OpenStage Key Module 15 ! page 17.
Peter Fox
Destinations?
Depending on how they are programmed, you can use the keys as:
• Function key ! page 66
• Selected dialling ! page 68
Each key can be programmed with one function.
Press the key briefly to activate the programmed function or dial the stored
number.
If you hold the key down, you will be prompted as to whether you want to
program this function key.
If the prompt is not displayed or a programmed function is not executed, then you can only launch key programming via the user menu
! page 67 (ask your service personnel about the current setting).
Your OpenStage is delivered with label strips. Write functions or names in
the white fields on the label strips.
The status of a function is shown by the LED on the corresponding function key.
Line and DDS keys can only be programmed by service personnel
via the service menu.
Meaning of LED displays on function keys
LED
Meaning of function key
S Off
The function is deactivated.
R On
The function is activated.
T Flashing1 Indicates the function status.
[1] In this manual, flashing sensor keys are identified by this icon, regardless of the flashing interval. The flashing interval represents different statuses, which are described in detail in
the corresponding sections of the manual.
The programmable keys on multi-line phones function as trunk keys
! page 20.
19
Getting to know your OpenStage phone
Trunk keys (on multi-line phones only)
The programmable keys on multi-line phones function as line keys. Each
key that is assigned the function "line" is handled as a line. This means up
to seven lines can be configured.
A distinction is drawn here between primary, secondary and phantom
lines. Each of these line types can be used on a private or shared basis
! page 20.
Primary line
All multi-line telephones have a primary line. This line can be reached in the
usual manner via your public phone number. Incoming calls are signaled on
this line.
To avoid conflict between individual multi-line phones, the functions
"Do not disturb" and "Call forwarding" can only be used for the primary line.
Secondary line
The secondary line on your phone is used as a primary line by another subscriber of the line trunk group. Your primary line, which is configured on another telephone in the line trunk group, simultaneously functions as the
secondary line on that telephone.
Phantom line
Phantom lines are not used as primary lines by any telephones in the line
trunk group. Phantom lines are established when the number of lines provided by a communications system exceeds the number of available
telephones.
Line utilization
• Private line: A line that is used by a single telephone. This line cannot
be used as a secondary line by another telephone.
• Shared line: A line that is configured on multiple telephones. The line
status is displayed for all telephones that share this line. If, for example,
a shared line is being used by a telephone, a status message indicating
that this line is busy is displayed on all other telephones (! page 21).
• Direct call line: A line with a direct connection to another telephone.
20
Getting to know your OpenStage phone
You can see the status of the line from the LED:
LED display
LED
S
T
R
Explanation
Not lit
The phone is in idle mode.
Flashing
•
•
Incoming call on the line (! page 106)
"Hold reminder" is activated (! page 80)
•
•
Outgoing call on the line
The incoming call was prioritized and selected
in accordance with the "Automatic line selection for incoming calls" option
Flickering
Fast blinking
The line is on "Hold".
Blinking
Call forwarding is activated
Illuminated The line is busy
21
Getting to know your OpenStage phone
Keypad
You can only use the digits 1 to 9 and 0 as well as the * and # characters
when dialing a number. To delete digits, select "Back" with the navigation
keys and confirm with =.
In situations where text input is possible, for example, when entering the
user password, you can also use the dial keys to enter text in addition to
the digits and special characters mentioned. To do this, press the numerical keys repeatedly.
Example: To enter the letter "h", press the number 4 key on the keypad
twice. When entering text, all characters available for the key pressed and
the character selected are briefly displayed.
Character overview (depends on the current language setting)
Key
1x
2x
1
]
1
a
b
c
2
3 d
e
f
3
g
h
i
4
j
k
l
5
n
o
6
ö
7 p
q
r
s
7
t
u
v
8
ü
9 w
x
y
z
9
2
4
5
6 m
8
0
(
3x
4x 5x 6x
ä
ß
0
1
2
[1] Next letter in upper case (active for maximum one second)
[2] Switch to digit input
) .
22
,
? !
’
"
-
(
)
@ /
:
_
Getting to know your OpenStage phone
Multi-function keys
Key Function during text input
) Write special characters.
Function when held down
Deactivate the ring tone
between upper and
Activate the telephone lock.
( Switch
lower case
Alphabetic labeling of dial keys is also useful when entering vanity numbers (letters associated with the phone number’s digits as indicated on the
telephone spell a name, e.g. 0700 - PATTERN = 0700 - 7288376).
Text editor
Additional options are available in the text editor. This is used when programming a forwarding destination, for example. In this way, you can,
for example, move the cursor freely and copy or insert text.
You can select further editor functions via the navigation keys and confirm
each one using =:
• OK: Applies changes and closes the editor
• Delete: Deletes characters from right to left
• Cancel: Discards changes and exits the editor
• Mode (here ( can also be used to switch):
– 123: Digits only
– ABC: Upper-case letters only
– Abc: First letter in upper case, subsequent letters in lower case
– abc: Lower case letters only
• Move cursor left: Moves the cursor to the left
• Move cursor right: Moves the cursor to the right
• Copy: Copies the entire content to the clipboard
• Paste: Inserts the entire content from the clipboard to the cursor position
23
Getting to know your OpenStage phone
Display
Your OpenStage 15 comes with a black-and-white LCD display. Adjust the
contrast to suit your needs (! page 149).
Idle mode
If there are no calls taking place or settings being made, your
OpenStage 15 is in idle mode.
Press the O key to return to the idle display again, for example,
from a call list (! page 28). To return to the idle display again from
the Service menu (! page 29), press the N key. You can also
configure a "Show telephone screen" function however for both
cases (see ! page 66) to return to the idle mode screen again.
Example:
Time
10:29
220870
SO 05
. . 08.07
:
l
Date
Open the idle menu
Own phone number
Idle menu
In idle mode press navigation keys :. The current function is displayed
in the second display line, or = ! page 18, then the idle menu opens.
You can call up various functions here. Entries may vary.
The idle menu may contain the following entries:
• Redial?
• Ringer off?
• Do not disturb on?
• Mobile logon?
• Cancel callbacks?
• Directed pickup
• Back?
24
Getting to know your OpenStage phone
Icons in the idle display
In the first and second line, the time, weekday, and date are displayed in
addition to icons for different situations and switches:
Icon
Explanation
The ring tone is deactivated.
The phone lock is activated.
The "Do not disturb" function is activated.
A mobile user is logged on to the telephone.
25
Getting to know your OpenStage phone
Context-dependent displays
Depending on the situation at hand, the display on your OpenStage phone
displays different content, to which you can respond intuitively.
Information on actual events
The following icons appear centered on the display when your phone is idle
and signal current properties or events.
Example: You missed two calls in your absence.
02
You have two new voice messages that you can open by pressing O
! page 28.
Icons for events
Icon
Explanation
You received new voice messages.
New entries have been added to the call lists.
Local call forwarding is active.
Context menus
If an arrow appears beside an entry in the second line, a context menu
whose options you can select using navigation keys < or :
(! page 18). The range of functions available is situation-specific.
Consultation?
First menu entry
(selected on callup)
Start conference?
Hold?
Blind transfer call?
Disconnect?
Directed pickup?
26
Other menu options
(hidden)
Getting to know your OpenStage phone
Press the O key to return to the telephony interface again, for
example, from a call list (! page 28). To return to the telephony
interface again from the Service menu (! page 29), press the N
key. You can also configure a "Show telephone screen" function
however for both cases (see ! page 66) to return to the telephony
interface screen again.
Idle display context menu
You receive the following functions (if activated) by pressing navigation
keys = or : . The current funtion is displayed in the second display
line. The other functions are hidden and can be selected using navigation
keys : or <:
Redial {1} 1234
Ringer off
First entry (selected when you call
up the menu, if you have already
dialed a phone number)
Do not disturb off
Mobile logon
Other menu options (hidden)
Cancel call backs
Directed pickup
Functions during a call
In many operating situations you are offered appropriate functions or notes
in the second line of the display. Other available functions remain hidden
and can be selected using navigation keys : or <:
Example: You set up a consultation call. The second line displays the first
of three dependant functions. Select the appropriate function and confirm
this with =.
012345|
First display line
Dial
Second display line
(current option)
Redial {1}
Retrieve held call
Other menu options
(hidden)
The menu with the functions closes automatically after you have executed
an action.
To delete info-only messages, press touche de navigation =.
27
Getting to know your OpenStage phone
Records
Entries in the call list and messages in your mailbox system (if configured)
are known as records.
The LED on the O key flashes to signal new missed calls or messages
! page 18.
Press the O key and use the navigation keys to select the required submenu.
• Messages
• Calls
You can use the navigation keys to navigate through the menus as described on ! page 18.
Messages
If configured (contact the relevant service personnel), this provides you
with access to your mailbox system e.g. HiPath Xpressions.
If your system is appropriately configured, activating this function opens
the menu for voicemail ! page 42.
Calls
This list appears as soon as you receive new missed calls if you select the
option Calls in the Records menu. You can then scroll up or down to reach
the Calls menu. The following calls or call attempts are logged as call lists:
• Missed: Missed calls
• Dialed: Dialed calls (with or without connection)
• Received: Answered calls
• Forwarded: Forwarded calls
The number of missed calls and unchecked calls is shown on the idle display.
Call lists
Each call list may contain up to 30 entries. Once this limit is reached, the
oldest entry in the log is deleted. Multiple calls from the same number are
only listed once.
The following data is saved, e.g. for missed calls:
• Phone number/name depending on available data.
• Number of call attempts.
• The date and time of the last call attempt from each user listed.
Entries can only be saved if the caller ID is displayed as a name, number
or both. If the caller ID is not transferred, the call is saved as "Unknown".
You can delete all the entries in the respective call list ! page 102.
After selecting an entry, you can dial it immediately by confirming
! page 93.
28
Getting to know your OpenStage phone
Program/Service menu
You can make local settings here.
Press the N key and confirm the User menu. If configured, enter and
confirm your personal user password.
You can use the navigation keys to navigate through the menus as described on ! page 18. Once the admin password has been entered, the
Admin menu is available to the relevant service personnel.
User settings
In the User menu (see ! page 185), settings options are provided that allow you to adapt the telephone to your individual requirements.
Select a menu using the navigation keys:
• "Date and time" ! page 150
• "Audio" ! page 154
• "Configuration" e.g. ! page 122 or ! page 75
• "Phone" ! page 149
• "Locality" ! page 154
• "Security" ! page 123 or ! page 126
• "Network information" ! page 163
• "Diagnostic information" ! page 176
• "Reset" ! page 164
If you are in one of these menus or submenus, depending on the situation,
you have the following options to leave the menus:
• Save & exit (If you have made a setting and want to keep it)
• Exit (no save) (If you have made a setting which you do not want to
use after all or if you do not want set any of the options)
• Back (If you want to leave the main menu or submenu)
• Press and hold the : key to access the option to leave the current
menu level.
• You exit the menu by pressing the N key and return to idle mode
! page 24.
29
Getting to know your OpenStage phone
Interrupting editing in the menu
You can interrupt editing in the menu, for example, to call someone or to
answer a call. Then press the N key. This takes you back to the point in
the menu from which you exited.
This is however only possible for a limited period which is by service personnel using the inactivity timeout setting. If the configured time expires,
you need to reenter your password when opening the menu and manually
go to the required point in the menu.
Interrupting the editing:
•
•
By pressing the N key you interrupt the editing, leave the menu and
return to idle mode ! page 24.
If you receive a call during editing and you answer it, you automatically
change to the call view (see also ! page 27).
To go back to editing mode in the menu, press the N key again.
Network information
Information about the IP address or name which was assigned to the
phone in the network and therefore the HTML address of the web interface.
V View information on the phone ! page 163
Contact your service personnel or refer to the OpenStage Administration Manual for more on the network information values listed
here.
Diagnostic.Information
V Provides information on all the main settings for the telephone. Can provide valuable help in support situations! page 176
Reset phone
V Personal settings made via the telephone menu or the web interface can
be reset to factory settings ! page 164.
Administration
You can access the administration area via the "Admin" function and by entering the administration password.
Refer to the administration manual supplied with your phone for more detailed information on this topic.
30
Getting to know your OpenStage phone
Control and monitoring function
A control or monitoring function can be activated on your phone for service
purposes by remote maintenance.
Control function
Service personnel have the option to activate and deactivate features of
the phone via remote maintenance. During maintenance the handset, microphone, loudspeaker and headset are deactivated. You are additionally
informed on the display that the control function is active.
Monitoring function
In order to detect malfunctioning of a phone for example, the service personnel install a monitoring function. You can use your phone as normal during monitoring. However you will first be informed about the operation
with a message on the display and prompted to allow monitoring.
If service personnel have activated a function on your phone, which continuously transmits operating data to a server, you will see the flashing
icon
in the upper display line.
31
Basic functions
Step by step
Basic functions
Please read the introductory chapter "Getting to
know your OpenStage phone" ! page 14 carefully before performing any of the steps described here on your phone.
Secure voice transmission
Prerequisite: The secure voice communication option
must be activated by your service personnel.
If you call a party or receive a call from a party over a secure connection, a padlock icon appears on the display.1
appears on the other party’s line. You can opt to have
voice connections that are no longer secure indicated
by a brief alerting tone and the message "Unencrypted
call" appears on the second line for two seconds (see
! page 158).
Answering a call
Your OpenStage phone rings with the tone signal set
when an incoming call is received. The call is also visually signaled on the call display.
If transmitted, calling party information (name, phone
number) appears on the display.
If you have set a pattern melody ! page 156 on
your phone, it is possible that service personnel
have preset a different pattern melody or pattern
sequence or deactivated the ringtone, depending on the call type (e.g. an external or internal
call).
An incoming call will interrupt any ongoing telephone setting operations. When the call ends,
you can press the N key to return to the point
in the menu structure where you were interrupted.
1. Closed for secure or open for nonsecure voice communication
32
Basic functions
Step by step
Answering a call via the handset
The phone is ringing. The caller is displayed.
^ Lift the handset.
if nec. + or - Set the call volume.
Answering a call via the loudspeaker
(speakerphone mode)
The phone is ringing. The caller is displayed.
Accept?
l
Confirm. The n key lights up.
or
n Press the key shown. The key lights up. The speakerphone function is activated.
if nec. + or - Set the call volume.
Suggestions for using speakerphone mode:
• Tell the other party that speakerphone mode is active.
• Adjust the call volume while speakerphone mode is
active.
• The ideal distance between the user and the phone
in speakerphone mode is about 50 cm.
33
Basic functions
Step by step
Directed pickup
You can pick up a call signaled at an absent coworker’s
phone. If a colleague has placed a call on hold on their
multi-line phone you can also pick up this call.
Accept call
Prerequisite: You know the coworker’s internal phone
number and the function is configured for you in
OpenScape Voice.
A coworker’s phone rings.
Directed pickup?
f
Select and confirm the option shown in the idle phone’s
context menu.
or.
^ Lift the handset.
or
n Press the key shown.
Directed pickup?
f
Select and confirm the option shown.
j Enter and confirm the relevant phone’s internal number.
You are connected to the calling party either via the
handset or in speakerphone mode.
34
Basic functions
Step by step
Picking up the held call
Prerequisite: Your colleague has placed a call on hold
on their multiline phone ! page 107. You know the coworker’s internal phone number and the function is configured for you in OpenScape Voice.
Directed pickup?
f
Select and confirm the option shown in the idle phone’s
context menu.
or.
^ Lift the handset.
or
n Press the key shown.
Directed pickup?
f
Select and confirm the option shown.
j Enter and confirm the relevant phone’s internal number.
You are connected to your colleague’s held call either via
the handset or in speakerphone mode.
35
Basic functions
Step by step
Switching from handset to speakerphone mode
Make note of the two different processes and activate, if necessary, your preferred setting
! page 157.
Prerequisite: You are conducting a call via the handset
and the microphone and loudspeaker functions have
been activated by service personnel.
Standard mode
n and \ Hold down the key and replace the handset. Then release the key and proceed with your call.
US mode
If the country setting is set to US, you do not have to
hold down the loudspeaker key when replacing the
handset to switch to speakerphone mode.
n Press the key shown.
\ Replace the handset. Proceed with your call.
{ or }
36
A secure voice communication is indicated by a
closed padlock icon on the graphic display; a nonsecure voice communication is indicated by an
open padlock icon on the graphic display (see
also ! page 32)
Basic functions
Step by step
Switching from speakerphone mode to
the handset
Prerequisite: You are conducting a call in speakerphone mode.
^ Lift the handset. The n key goes out.
Open listening
You can let other people in the room join in on the call.
Let the other party know that you have turned on the
loudspeaker.
Prerequisite: You are conducting a call via the handset.
Activating
n Press the key shown.
Deactivating
n Press the lit key.
Switch to speakerphone mode
n and \ Hold down the key and replace the handset. Then release the key and proceed with your call.
37
Basic functions
Step by step
Activating/deactivating the microphone
To prevent the other party from listening in while you
consult with someone in your office, you can temporarily switch off the handset microphone or the handsfree
microphone.
Prerequisite: You are conducting a call. The "Mute" key
is configured.
Deactivating the microphone
S Press the "Mute" key.
Activating the microphone
R Press the illuminated "Mute" key.
Ending a call
Disconnect?
m
Select and confirm the option shown.
or If you are conducting a call via the handset:
\ Replace the handset.
or In speakerphone mode:
n Press the lit key.
38
Basic functions
Step by step
Group call
Your service personnel can incorporate multiple telephones in a call pickup group. If your telephone belongs
to a pickup group, you can also accept calls intended for
other members of the group.
A group call is displayed on the phone. Service personnel may have made the following settings for signaling:
Telephone status
Ring on group call
= Yes
Ring on group call
= No
Ringer on
Ringtone
Loudspeaker
Beep
Loudspeaker
Ringtone
Loudspeaker
Beep
Handset
Silent
in
Connection
Ringtone
off
Handset
Handset
Beep
Open listening Handset and loudspeaker
Beep
Handset and loudspeaker
Open listening Beep
Loudspeaker
Beep
Loudspeaker
Speakerphone mode
Beep
Loudspeaker
Beep
Loudspeaker
Nothing
Nothing
Nothing
Beep
Handset
Silent
in
Connection
Handset
Handset
Beep
Open listening Handset and loudspeaker
Beep
Handset and loudspeaker
Open listening Beep
Loudspeaker
Beep
Loudspeaker
Speakerphone mode
Beep
Loudspeaker
Beep
Loudspeaker
The volume settings can be found from ! page 154.
39
Basic functions
Step by step
Further service personnel settings for group calls:
• The group call can be picked up both by lifting the
handset and via the "Pickup call" menu option.
• The group call be picked up via the "Pickup call"
menu option but not by just lifting the handset.
• A key is programmed for call pickup.
• Open a pop-up menu with the Call pickup key when
a group call is waiting.
Picking up a group call with the call pickup key
Prerequisite: The Call pickup key is configured. Your
service personnel have set up the group call such that it
is only displayed through flashing of the Call pickup key.
The phone can also ring when idle.
A group call is waiting. The Call pickup key flashes. The
group call is not shown on the display.
R Press the key with the "Call pickup" function.
The group call is now shown on the display with
Pickup: Caller
for: Party
The pop-up menu opens:
Picking up a group call immediately via the pop-up
menu
Prerequisite: Your service personnel have set up the
group call such that it will be shown immediately on the
display and the pop-up menu will open.
• A group call is waiting and is shown on the display
with
Pickup: Caller
for: Party
40
Basic functions
Step by step
Picking up a group call
The pop-up menu opens:
Pickup call?
l
Confirm.
or
^ Lift the handset (only if the appropriate function is set
by your service personnel)
or
R Press the key with the "Call pickup" function or press it
again if call answering was initiated via the key. The
speakerphone function is activated.
Ignoring a group call
Ignore?
f
Select and confirm the option shown. The phone stops
signaling the group call.
41
Basic functions
Step by step
Listening to voicemail
To use this function, you need to have a voice mailbox
set up on your communication platform for voicemails
(see ! page 28).
The message key O flashes to indicate new messages and the F icon appears on the display. The LED
only extinguishes when all new messages have been
picked up and there are no missed calls.
Picking up messages
O Press this key when the phone is in idle mode. The
menu for data records opens.
Messages
Select and confirm to open the menu for voicemail.
If messages are waiting, you will be shown a list with
the new messages and the messages you have already
listened to, sorted by status. The number of the respective messages is indicated. You can browse the list using the cursor keys.
Call Mailbox
Confirm the option shown to call the mailbox. Follow
the voice instructions. You may need to enter a password.
Calling the mailbox directly
You can also call the mailbox directly without using the
menu. The mailbox answers even if there are no messages waiting.
^ Lift the handset.
O Press this key. The mailbox answers. Follow the voice
instructions. You may need to enter a password.
You can call the mailbox any time you see the
"Please dial" prompt on the display.
42
Basic functions
Step by step
Call control
To ensure that you do not miss any important calls, service personnel can configure a key that blinks when a
call is waiting, for instance, when you are dialling a number or when two calls come in simultaneously.
Call control does not work with MultiLine telephones
Two calls simultaneously
Prerequisite:The call control key (2nd alert) is configured and call waiting is allowed (! page 86).
Y Y two calls ring at the same time.
Caller information from the first caller is displayed and
you have the following options:
• Accept
• Reject
• Deflect
T The "Call control" key is blinking and you hear a notification tone.
Display second caller
T Pressing the blinking "Call control" key will display the
second caller's information and you again have three
options to choose from.
Return to first caller
T Press the blinking "Call control" key again to return to the
first caller's displayed information.
Accept a call
If you accept one of the calls, the other call is treated as
a second call (see ! page 83)
While dialling
Please note that the "Busy when dialing"
! page 96 function is disabled after call control
is configured. The exception is if you dial a number during a Consult ! page 50.
43
Basic functions
Step by step
Prerequisite: The "Call control" key (2nd alert) is configured and call waiting is allowed (! page 86).
^ j You receive a call while you are dialling. The "Call control" key is blinking and you hear a notification tone.
T Press the blinking "Call control" key. Dialling is interrupted. The caller's information is displayed and you have
the following options:
• Accept
• Reject
• Deflect
44
Basic functions
Step by step
Making calls
If you selected the option "Busy When Dialing"
! page 96, you will not be interrupted by an incoming call. In this case, the caller hears the busy
signal.
Off-hook dialing
^ Lift the handset.
j Enter the station number. If nec. Correct input using the
navigation keys ! page 18.
Dial
Confirm or wait until the dial delay expires (see
! page 94).
or
Redial {1} ##?
l
Confirm. ## represents the last number dialed.
The connection is set up.
If you are using a dial plan and Immediate dialing
is set (see ! page 47, dialing is automatically
performed as soon as the character string entered matches an entry in the dial plan.
45
Basic functions
Step by step
On-hook dialing
The connection is set up with on-hook dialing via the
loudspeaker (speakerphone mode).
n Press the key shown.
j Enter the station number. If nec. Correct input using the
navigation keys ! page 18.
= Press or wait until the dial delay expires (see
! page 94).
or
Redial {1} ##?
l
Confirm. ## represents the last number dialed.
First enter the number
First enter the number. The loudspeaker key illuminates
when you enter the first digit.
j Enter the station number. If nec. Correct input using the
navigation keys ! page 18.
Dial
Confirm or wait until the dial delay expires (see
! page 94).
The connection is set up.
If you are using a dial plan and Immediate dialing
is set (see ! page 47), dialing is automatically
performed as soon as the character string entered matches an entry in the dial plan.
46
Basic functions
Step by step
Immediate dialing
Immediate dialing should only be activated if service
personnel has configured and approved a dial plan.
Immediate dialing is deactivated by default. For this reason after entering the number you must either confirm
the "Dial" option or wait until the dial delay expires to set
up the connection. If Immediate dialing is configured,
your call is automatically dialed as soon as the string entered matches an entry in the dial plan.
Activating or deactivating immediate dialing
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Immediate dialing = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Confirm.
47
Basic functions
Step by step
Dialing using the hot or warm line function
Your service personnel can configure a hot or warm line
for your phone.
If you lift the handset of the phone or press the loudspeaker key
• with a hot line immediately or
• with a warm line after a defined period of time,
• a number specified by service personnel is dialed.
Examples:
• The phone in the lift immediately dials the reception
number.
• The phone at a patient’s bed dials the ward number
e.g. after a minute if no other number is dialed.
48
Basic functions
Step by step
Redial
Redialing from the call list
Only calls to the primary line are received on
multi-line phones (! page 13).
O Press the key. The "Records" menu opens.
Calls
l
Select and confirm (see also ! page 28).
Dialed
l
Select and confirm the option shown. The Dialed call list
opens
01.01 f
If entries are saved, select and confirm the required entry.
l
Confirm. The phone number associated with the list entry is dialed.
998324
Dial
Redialing from the display dialog
^ Lift the handset.
or
n Press the key shown.
Redial {1} ##?
l
Confirm. The last phone number entered is dialed.
Redialing from the idle menu
: or = press the key shown to open the idle menu
Redial {1} ##?
l
{ or }
Confirm. The last phone number entered is dialed.
A secure voice communication is indicated by a
closed padlock icon on the graphic display; a nonsecure voice communication is indicated by an
open padlock icon on the graphic display (see
also ! page 32).
49
Basic functions
Step by step
Consulting a second party
You can call a second party while a call is in progress.
The connection to the first party is on hold.
Prerequisite: You are conducting a call.
Consult?
l
Confirm.
or Start conference
Konferenz starten
Select and confirm the option shown in the context
menu for the call connection when you intend to set up
a conference with the new participant. You can also use
an already configured Conference key in this instance.
j Enter and confirm the second party’s phone number.
If you want to use a call list for the consultation,
select Hold in the context menu instead of
Consult or press the Hold key and then select
the required call list (! page 93).
Alternatively you can select a call list without
using the Hold functions - the active call is
automatically placed on Hold.
50
Basic functions
Step by step
Ending a consultation call
You end the consultation
Disconnect & return?
f
Select and confirm the option shown.
The consultation call is disconnected. The call with the
first party is resumed.
The second party hangs up
Once the second party hangs up, you are prompted to
resume the first call.
Retrieve held call
Confirm the option shown. You are reconnected with
the first party.
Switching to the held party (alternating)
Prerequisite: You are conducting a consultation call.
Alternate?
l
Select and confirm the option shown.
In the first display line, the phone number or name and
the duration of the active connection are displayed.
You can switch back and forth between two subscribers by repeatedly selecting and confirming
"Alternate".
Ending an alternate operation
Disconnect & return?
f
Select and confirm the option shown.
The active call is disconnected and the held call is restored.
51
Basic functions
Step by step
Putting on hold and retrieving successively or
simultaneously
Putting an active call on hold
Prerequisite: You are conducting a consultation call
! page 50 or have accepted a second call ! page 83.
The "Hold" key must be configured ! page 66
S Press the "Hold" key. The key lights up. The consultation
or second call and the first call are put on hold.
Retrieving the first call
< Switch to the first call.
R Press the illuminated "Hold" key. You are connected
with the other party. The consultation or second call
continues on hold.
Retrieving the second call
: Switch to the held consultation or second call
R Press the illuminated "Hold" key. You are connected
with the other party. The first called is put on "Hold"
again.
52
Basic functions
Step by step
Connecting parties
You can connect the first party with the party you consulted, clearing down your connection to both parties in
the process.
Prerequisite: You are conducting a consultation call
! page 50 and call joining is allowed ! page 53.
Complete Xfer?
f
Select and confirm the option shown.
The active and held calls are joined. You are disconnected from the call.
or Connect by hanging up
] or n Replace the handset or, if you are in speakerphone
mode, press the loudspeaker key. The other two parties
are now connected to one another.
Allowing call joining
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Confirm.
if nec.j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Allow call joining = Yes
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
l
Select and confirm the option shown.
Save & exit
53
Basic functions
Step by step
Call forwarding
You can forward calls for your phone to another phone.
You can also change, activate and deactivate call forwarding during a call. The function Forwarding must be
authorized by service personnel.
Prerequisite: The call forwarding function is programmed (! page 55).
Three forwarding conditions can be programmed in the
forwarding menu:
• All Calls
• Busy
• On no reply
Because of its direct impact, "All Calls" call forwarding
has the highest priority followed by "No reply" and
"Busy".
If active, "All Calls" call forwarding is indicated on the display when the phone is idle.
Forwarded calls can be logged in a call list (see
! page 28).
The menu Forwarding offers you three types of call forwarding:
" All calls
" Busy
Destination phone number
Destination phone number
" No reply
Destination phone number
A phone number may already be assigned to each call
forwarding type. For example, one Destination could be
Destination 12345.
54
Basic functions
Step by step
Activate or deactivate immediate forwarding
Prerequisite:You have configured the key for "Variable
call forwarding" (see ! page 72). Otherwise you can
configure the settings for call forwarding via the user
menu (! page 77). It is recommended to configure the
key so that you can use the following convenience functions.
S Press the "Variable call forwarding" key.
Deactivating call forwarding
If call forwarding was activated for All calls it will now
be automatically deactivated.
or Activate forwarding to last destination.
The pop-up menu opens:
The message:
"Umleitung aktivieren nach" is displayed with the
number of the last forwarding destination and you have
the following options:
• Accept
• Umleitungsziel festlegen
• Edit call forwarding
• Cancel
Use last forwarding destination
Accept?
l
Select and confirm the option to use the last saved destination for All calls again. Call forwarding to this destination is immediately activated for All calls and the key
R illuminates.
or Activate with variable destination phone numbers
If you want to use a new forwarding destination:
Umleitungsziel festlegen
f
Select and confirm the option shown.
j Enter and confirm the new destination phone number.
or Confirm saved destination phone number (displayed).
Call forwarding to this destination is immediately activated for All calls and the key R illuminates.
55
Basic functions
Step by step
Saving destination phone numbers for call
forwarding
You can also enter the call forwarding settings via
the user menu (! page 77) or via the WEB-Oberfläche ! page 178.
Prerequisite:You have configured the key for "Variable
call forwarding" (see ! page 72).
S Press the "Variable call forwarding" key.
The pop-up menu opens:
The message:
"Umleitung aktivieren nach" is displayed with the
number of the last forwarding destination and you have
the following options:
• Accept
• Umleitungsziel festlegen
• Edit call forwarding
• Cancel
Edit call forwarding?
f
Select and confirm the option shown.
Three types of call forwarding are offered in the settings
menu:
• All calls
• Busy
• No reply
You can check whether Busy or No reply call forwarding is activated.
Save destination phone number
" All calls?
l
Select and confirm type of forwarding (here for instance
All calls)
Enter destination?
f
Select and confirm the option shown.
j Enter/edit and confirm the destination phone number.
56
Basic functions
Step by step
or Edit favourites
You can configure up to five destination phone numbers for call forwarding. These destination phone numbers can then be assigned different forwarding conditions.
" All calls
l
Select and confirm type of forwarding (here for instance
All calls)
Edit favorites?
f
Select and confirm the option shown.
Destination 1
l
E.g. select and confirm first destination.
j Enter/edit and confirm the destination phone number.
If necessary, define additional destination phone numbers.
Save & exit
l
Select and confirm the option shown
Copy and insert destination phone numbers
The current destination phone number for a call forwarding type is copied. For example, the current destination phone number for All calls should also become
the current destination phone number for No reply.
Prerequisite:You have configured the key for "Variable
call forwarding" (see ! page 72).
S Press the "Variable call forwarding" key.
The pop-up menu opens:
Edit call forwarding?
f
Select and confirm the option shown.
Three types of call forwarding are offered in the settings
menu:
• All calls
• Busy
• No reply
1. Copy
" All calls: 3339
l
Select and confirm type of forwarding (here for instance
All calls)
Copy?
f
Select and confirm the option shown.
2. Insert
57
Basic functions
Step by step
" No reply
f
Select and confirm type of destination forwarding (here
for instance No reply)
Paste?
f
Select and confirm the option shown.
# No reply: 3339
f
Both types of call forwarding now have the same destination phone number. The call forwarding type No reply
is automatically activated.
Assign a destination phone number for call forwarding
Prerequisite: At least one destination phone number
has already been saved.
" All calls: 3339
l
Select and confirm type of forwarding (here for instance
All calls)
3336
f
Select and confirm a saved destination.
# All calls: 3336
l
Call forwarding is activated and the new destination is
displayed.
N Press the illuminated key to open the call display. If All
calls was activated, the forwarding destination is displayed with the forwarding symbol and the R key illuminates. The Busy and No reply types of call forwarding are not displayed.
Activate/deactivate call forwarding
Prerequisite: There is already a forwarding destination
configured for the relevant forwarding type and you
have configured the key for "Variable call forwarding"
(see ! page 72).
S Press the "Variable call forwarding" key.
The pop-up menu opens:
The message:
"Umleitung aktivieren nach" is displayed with the
number of the last forwarding destination and you have
the following options:
• Accept
• Umleitungsziel festlegen
• Edit call forwarding
• Cancel
58
Basic functions
Step by step
Edit call forwarding?
f
Select and confirm the option shown.
" All calls: 3339
l
Choose one of the forwarding types offered
"
"
"
All calls: 3339 (deactivated is the default setting)
Busy: 3335
No reply: 3336
and confirm your selection. Here for example All calls.
Turn on:
l
Select and confirm the option shown. Call forwarding is
activated. This type of call forwarding is deactivated
with Turn off.
Call forwarding settings can appear as follows:
"
#
#
All calls: 3339 (default setting is off)
Busy: 3335
No reply: 3336
N Press the illuminated key to open the call display. If All
calls was activated, the forwarding destination is displayed with the forwarding symbol and the R key illuminates. The Busy and No reply types of call forwarding are not displayed.
59
Basic functions
Step by step
Defining the ring duration before call forwarding on
no reply
You can define how often the phone should ring before
the "No reply" call forwarding is activated.
This setting is only available if the "Server features" function was deactivated by the service
personnel.
z You can also configure this setting via the Web interface
! page 178.
Prerequisite: You have configured the key for "Variable
call forwarding" (see ! page 72). Otherwise you can
configure the settings for call forwarding via the user
menu (! page 77).
S Press the "Variable call forwarding" key.
Within three seconds:
Edit call forwarding
f
Select and confirm the option shown.
" No reply: 3335
f
Select and confirm the type of call forwarding.
Set delay
m
Select and confirm the option shown.
j Enter the desired time in seconds and confirm your entry. The set time is displayed with the option. Call forwarding is activated.
N Press the illuminated key to open the call display.
60
Basic functions
Step by step
Call forwarding chain
Sometimes calls to a station are forwarded to another
station which also has call forwarding or DND activated.
This can create a call forwarding chain consisting of several telephones where the last member of the chain is
your phone.
A popup window opens on your phone’s screen with
the following information:
• Who is calling
• Who forwarded first or last.
• The reason for the forwarding is displayed by an
icon.
You can set whether the station that forwarded first or
last is displayed (see ! page 78).
61
Basic functions
Step by step
Callback
You can request a callback if the station called is busy or
if nobody answers.
You receive a callback when the other party’s line becomes free.
This option must be activated by your service
personnel.
This option is only available if both you and service personnel have activated the function
(! page 64).
Requesting callback
Prerequisite: The station called is busy or nobody answers.
Call back?
m
Select and confirm the option shown.
Deleting callback requests
You can delete scheduled callback requests if you no
longer need to return a call, for example, at the end of
the working day.
Prerequisite: At least one callback was requested. The
phone is idle.
Cancel call backs?
f
Select and confirm the option shown.
Disconnect?
m
All callback requests are deleted.
62
Basic functions
Step by step
Responding to a callback
Prerequisite: A callback was requested. Your phone
rings and the station information appears on the screen.
Accepting a callback
Accept
l
Select and confirm the option shown.
Rejecting a callback
Prerequisite: The function Reject is authorized by service personnel.
Reject?
f
Select and confirm the option shown.
The callback request is deleted. The caller hears the
busy signal. The caller’s phone number is added to the
missed calls list.
Forwarding a callback
Prerequisite: The function Deflect is authorized by service personnel.
Deflect?
m
Select and confirm the option shown.
j Enter and confirm the phone number.
63
Basic functions
Step by step
Allow callback
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Confirm.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Outgoing calls?
Confirm.
Callback = No
f
Select and confirm the option shown.
Yes
l
Select and confirm to activate the callback function.
Save & exit
l
Select and confirm the option shown.
64
Basic functions
Step by step
Calling back missed calls
Calls received while you are absent are indicated by a
message on the idle display (! page 25). The O function key also lights up.
Missed calls are logged in the missed calls list. This list
provides information on the missed call and lets you call
back the number directly (call lists ! page 28).
O Press the key shown.
Calls
m
Select and confirm the option shown.
Missed
l
Select and confirm the option shown.
998324
Dial
01.01m
l
Select and confirm the entry you want.
Confirm
The phone number associated with the entry is dialed.
65
Programmable keys
Step by step
Programmable keys
The phone features a range of functions that can, if required, be stored on programmable keys.
The phone comes with eight programmable keys, all of
which can be programmed on two separate levels.
The "Shift" programmable key to switch between the
two key levels is already preassigned. You should keep
this key if possible to be able to switch between the
two key levels.
The keys can also be programmed via the Web interface
(! page 178).
List of available functions
1.
2.
3.
4.
Unallocated
Selected dialing
Repeat dialing
Forward all calls
5. Forward no reply
6. Forward busy
7. Mute
8. Ringer off
9. Hold
10. Alternate
11. Blind transfer call
12. Transfer call
13. Deflecting
14. Shift
15. Conference
16. Headset
17. Do not disturb
66
18. Group pickup
19. Repertory dial
20. Feature toggle
21. Show telephone
screen
22. Mobility
23. Directed pickup
24. Release (disconnect)
25. Callback
26. Cancel callbacks
27. Consultation
28. Call Waiting toggle
29. Immediate ring
30. Call recording
31. PreView
32. Start application
33. Built in fwd
34.
Programmable keys
Step by step
Programming a key
z You can also configure this setting via the Web interface
! page 178.
Beginning programming
Directly via the key
S Hold down the programmable key you want to assign a
function to until the programming prompt is displayed.
If the prompt is not displayed or a programmed
function is not executed, then you can only
launch key programming via the user menu (ask
your service personnel about the current setting).
OK
Confirm to begin programming. The key illuminates
continuously.
or Via the user menu
You can also program keys via the user menu.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the User password.
Phone
Select and confirm the option shown.
Program keys
Select and confirm the option shown. You are prompted
to press the key you wish to program.
S Press the key you want to program until the input field
opens. The key illuminates continuously.
67
Programmable keys
Step by step
Beginning programming
Normal
Select and confirm the option shown to program the
first level.
or
Shifted
Select and confirm the option shown to program the
second level.
Do not disturb
Select and confirm the required function in the list (e. g.
Do not disturb).
Save & exit
Select and confirm the option shown.
Programming enhanced functions
Repertory dial
S Hold down the key you want to assign a function to until
the programming prompt is displayed.
If the prompt is not displayed or a programmed
function is not executed, then you can only
launch key programming via the user menu (ask
your service personnel about the current setting).
OK
Confirm to begin programming. The key illuminates
continuously.
z You can also configure this setting via the Web interface
! page 178.
Normal =
f
Select and confirm the option shown to program the
first level for instance.
Repertory dial
f
Select and confirm the required function.
Setting
f
Select and confirm this option to enter a destination
phone number.
j Enter and confirm a stations’s destination phone number.
You can select and insert special characters in the dialing sequence:
« Clear call
68
Programmable keys
Step by step
~ Make consultation
» Make normal call
¬ Pause
The menu also offers the following functions:
• Move cursor right and left
• Copy
• Paste
• Mode selection
• Cancel
• OK
Save & exit
l
Select and confirm the option shown.
The repertory dial can be up to 40 characters
long.
69
Programmable keys
Step by step
Feature toggle
Only available for Hunt group functions (! page 140).
S Hold down the key you want to assign a function to until
the programming prompt is displayed.
If the prompt is not displayed or a programmed
function is not executed, then you can only
launch key programming via the user menu (ask
your service personnel about the current setting).
OK
Confirm to begin programming. The key illuminates
continuously.
z You can also configure this setting via the Web interface
! page 178.
Normal =
f
Select and confirm the option shown to program the
first level for instance.
Feature toggle
f
Select and confirm the required function.
f
Select and confirm this option to enter a code.
l
Select and confirm the option shown.
Setting
Save & exit
70
j Enter and confirm the code (see ! page 148)
Programmable keys
Step by step
Configuring a fixed forwarding key
S Hold down the programmable key you want to assign a
function to until the programming prompt is displayed.
If the prompt is not displayed or a programmed
function is not executed, then you can only
launch key programming via the user menu (ask
your service personnel about the current setting).
OK
Confirm to begin programming. The key illuminates
continuously.
z You can also configure this setting via the Web interface
! page 178.
Normal =
f
Select and confirm the option shown to program the
first level for instance.
Forward all calls
f
Select a forwarding type:
• Forward all calls
• Forward no reply
• Forward busy
Select and confirm the required function.
Setting
f
Select and confirm this option to enter the forwarding
destination.
j Enter and confirm the phone number of the forwarding
destination.
Save & exit
l
Select and confirm the option shown.
71
Programmable keys
Step by step
Configuring a variable call forwarding key
With the "Variable call forwarding" key you can
• Immediately activate or deactivate the call forwarding for "All calls" ! page 55
• Edit the call forwarding ! page 56
S Hold down the programmable key you want to assign a
function to until the programming prompt is displayed.
If the prompt is not displayed or a programmed
function is not executed, then you can only
launch key programming via the user menu (ask
your service personnel about the current setting).
OK
Confirm to begin programming. The key illuminates
continuously.
z You can also configure this setting via the Web interface
! page 178.
Normal =
f
Select and confirm the option shown to program the
first level for instance.
Integ. forward
f
Select and confirm the option shown
Save & exit
l
Select and confirm the option shown.
72
Programmable keys
Step by step
Using programmed keys
The use of programmed functions depends on the
phone’s status. The relevant display appears once you
have pressed a key.
Example 1: Calling saved number
Prerequisite: The idle menu is displayed on the graphic
display.
S Press key for stored contact. Connection setup is
shown in the display.
Example 2: Call Waiting toggle Activating/
deactivating
You can press a key to activate or deactivate call waiting
functionality, even during a call. The perquisite for this is
that a second call is permitted (! page 86). By default
a second call is permitted.
T Press the "Call Waiting toggle" key. The key goes out.
The second call function is deactivated. The call is rejected or forwarded.
Example 3: Immediate ring
This function allows you to switch the preset delay
(! page 117) on and off for all line keys. By default the
delay is set, the key does not illuminate.
S Press the "Immediate ring" key. The key lights up. The
delay ringtone is disabled. An incoming call rings immediately regardless of what delay time is configured.
73
Programmable keys
Step by step
Resetting programmable keys
Here you can reset keys you configured back to factory
settings (see also ! page 164).
N Press the key shown.
User
Confirm.
if nec.j Enter and confirm the user password.
Reset
Select and confirm the option shown to switch to the
Reset user data menu.
Function key data
m
Yes
f
Reset phone
Select the option shown.
Select and confirm the option shown to delete the content of all keys.
Select and confirm "Reset selected user data." The contents of the keys you configured are deleted.
Keys which can only be configured by service
personnel remain unchanged.
74
Enhanced phone functions
Step by step
Enhanced phone functions
Incoming calls
Deflecting a call
Using call deflection
Prerequisite: An incoming call is displayed or signaled.
"Deflect" must be allowed.
Deflect?
m
Select and confirm the option shown.
089008844
l
If a destination phone number is stored (! page 75),
you can select and confirm it. The call is deflected.
or If you did not set a phone number when programming
call deflection, you are now prompted to enter a destination phone number for call deflection.
j Enter and confirm the destination phone number. The
call is deflected.
Permitting call deflection
z You can also configure this setting via the Web interface
! page 178. "Deflect" must be authorized by service
personnel.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
Deflecting?
Select and confirm the option shown.
Allow deflection = No
f
Select and confirm the option shown.
75
Enhanced phone functions
Step by step
Yes
l
Confirm.
Default destination =
f
Select and confirm the option shown.
j Enter and confirm the phone number to which the station should be deflected.
Entering a destination phone number is not mandatory when call deflection is active. If you want
to deflect an incoming call, you are prompted to
enter a destination phone number if there is
none stored.
or Deflecting to a DSS number
A call can be deflected to a direct station selection
(DSS) subscriber using the DSS key, if the key is configured and the deflect function is activated by your service personnel ! page 112.
Deflect to DSS = Yes
m
Information only, as set by service personnel: Yes or No.
Rejecting a call
You can reject an incoming call.
Prerequisite: An incoming call is displayed or signaled.
"Reject" must be authorized by service personnel.
Reject?
f
Select and confirm the option shown.
The caller hears a busy signal.
If the rejected caller’s phone number is transmitted, it is saved in the call list. You can then call
this party back at a later time.
76
Enhanced phone functions
Step by step
Configuring call forwarding
You can also enter the call forwarding settings via
the Forwarding key (! page 55).
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
Forwarding?
Select and confirm the option shown.
Configuring forwarding
Settings?
Select and confirm the option shown.
For a description of the settings, see chapter ”Call forwarding” ! page 54.
77
Enhanced phone functions
Step by step
Setting alerts
Use the Call forward alerts menu to enable and disable
visual and audible alerts for call forwarding (not possible
with the Forwarding key).
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
Forwarding?
Select and confirm the option shown.
Alerts
Select and confirm the option shown.
Visual alerts= No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown in the Yes/No context menu.
or.
Audible alerts= No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
or.
Forwarding station...
m
Select the option shown.
Display last
f
Select and confirm Display last/Display first.
Save & exit
l
Select and confirm the option shown.
78
Enhanced phone functions
Step by step
Placing a call on hold
You can use this function to place an ongoing call on
hold, for instance, to prevent the other party overhearing a conversation with a colleague in the same room.
Prerequisite: You are conducting a call.
Hold ?
f
Select and confirm the option shown in the connections’s context menu.
or
S Press the "Hold" key. The key lights up. (The "Hold" key
must be configured ! page 66.)
Retrieving a held call
Reconnect ?
l
Select and confirm the option shown in the connections’s context menu.
or
R Press the illuminated "Hold" key. (The "Hold" key must
be configured ! page 66.)
Using line keys
On multi-line telephones you can use the line keys to
place ongoing calls on hold.
R Press the corresponding line key. The line key LED
starts flickering. The call is now on hold.
Retrieving a held call:
T Press the corresponding line key. The line key LED
lights up. The call is retrieved.
The LED display ! page 21 indicates that the
call is on hold to other multi-line telephones
where this line is also configured. These phones
can then pick up the call.
79
Enhanced phone functions
Step by step
Held call wait status
After placing a call on hold, you can replace the handset
and then decide if the call should be retrieved or disconnected.
Prerequisite: You placed a call on hold and replaced the
handset.
Retrieve held call ?
l
Select and confirm the option shown to resume the call
in speakerphone mode.
or
Disconnect ?
f
Select and confirm the option shown to disconnect the
call.
The held call is signaled as an incoming call after
a specified period of time.
Activating/deactivating the hold reminder tone
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Allow hold rem. = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
80
Enhanced phone functions
Step by step
Setting the hold reminder time
Use the "Hold reminder" function to set the time after
which you want to receive an automatic reminder about
a held call.
The minimum value is 1, that is, the reminder is output
after one minute. The maximum value is 99 minutes.
Press 0 to deactivate the delay.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Hold rem. delay=3
f
Select and confirm the option shown.
j Enter a value between 1 and 99 in the input mask and
confirm.
Save & exit
l
Select and confirm the option shown.
81
Enhanced phone functions
Step by step
Music on hold
If the Music on hold option is active, music is played
back when you are placed on hold by another party.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Music on hold = No
f
Select and confirm the option shown
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
82
Enhanced phone functions
Step by step
Call waiting (second call)
You can accept a second incoming call in the course of
an ongoing call. The caller hears the on-hook signal
while you hear a call-waiting signal tone. A bell appears
on the display and next to it the phone number of the
caller is shown.
You can ignore or accept the second call. Before you accept the second call, you can end the first call or place
it on hold for subsequent retrieval.
You can block the second call or the signal tone
(! page 86).
Accepting a second call
Prerequisite: You are conducting a call and call waiting
is allowed (! page 86).
Accept
l
Select and confirm the option shown.
You can talk to the second party.
The connection to the first party is on hold.
During the call with the second party, additional functions are available for selection:
• Alternate (see ! page 51),
• Complete transfer (see ! page 53),
• Conference (see ! page 97),
• Blind transfer (see ! page 88),
• Hold (see ! page 79).
• put on hold and retrieve second and first call successively ! page 52
Consultation call from second call
If the second call is your active call you can initiate a
consultation call from it.
From a consultation call in the second call you can
• initiate a conference
• toggle between the second call and a consultation
call
• put on hold and retrieve second and first call successively ! page 52
• transfer a call
• disconnect the calls again
During a consultation in the second call, the first call is
parked and can only be unparked when the consultation
or second call ends or these calls were connected.
83
Enhanced phone functions
Step by step
Disconnect & return?
m
Select and confirm the option shown.
The call with the second party is disconnected and the
connection to the first party is retrieved.
Ignoring second call
Prerequisite: You are conducting a call and call waiting
is allowed (! page 86).
Ignore?
f
Select and confirm the option shown.
The caller still hears the on-hook signal. You can subsequently Accept, Reject or Deflect the second call.
While the ignored second call continues to wait, from
the active call you can:
• make a consultation call
• initiate a conference
• toggle between the consultation call and your call
party
• transfer a call
A third call would be rejected with the busy signal
If you have disconnected the first call, the ignored second call rings like a normal call.
Rejecting a second call
Prerequisite: You are conducting a call and call waiting
is allowed (! page 86).
Reject?
f
Select and confirm the option shown.
The second call is rejected. The caller hears the busy
signal. The caller’s phone number is added to the
missed calls list.
84
Enhanced phone functions
Step by step
Deflecting a second call
Prerequisite: You are conducting a call and call waiting
is allowed (! page 86).
Deflect?
m
Select and confirm the option shown.
If a destination phone number is stored (! page 75),
you can select and confirm it. The call is deflected.
or If you did not set a phone number when programming
call deflection, you are now prompted to enter a destination phone number for call deflection.
j Enter and confirm the destination phone number.
The second call is deflected to the destination specified. You are reconnected with the first party.
Connecting parties
Complete Xfer
Select and confirm the option shown. The other two
parties are now connected to one another. You can now
hang up or dial another number for instance.
or Connect by hanging up
Prerequisite: Connecting by hanging up is activated
(ask your service personnel) and "Switch assignment"
must be set to "Yes" (! page 87). Before you can be
connected by hanging up you must have toggled at
least twice (! page 51).
] or n Replace the handset or, if you are in speakerphone
mode, press the loudspeaker key. The other two parties
are now connected to one another.
85
Enhanced phone functions
Step by step
Allowing call waiting
If the Call waiting (second call) function is deactivated, a caller hears the busy signal if you are already conducting a call.
z You can also configure this setting via the Web interface
! page 178.
Prerequisite: The option was programmed by your service personnel.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Incoming calls?
Select and confirm the option shown.
Handling?
f
Select and confirm the option shown.
Allow call waiting = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
Assuming Allow call waiting is generally activated,
you can toggle the configured sensor key to switch call
waiting on/off (! page 73).
86
Enhanced phone functions
Step by step
Toggling associate
Set the "Toggle associate" function to Yes if you want to
connect to a second or pickup call by hanging up.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Toggle associate = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
87
Enhanced phone functions
Step by step
Transferring a call
You can transfer your current call to another party with
or without consultation.
Blind transfer
Prerequisite: You are conducting a call. The options "Allow Call Transfer" and "Transfer on Ring" were selected
(! page 89).
Blind transfer call?
f
Select and confirm the option shown.
j Enter the phone number of the second party to whom
you want to transfer the call.
Start transfer?
f
Confirm or wait until the autodial delay expires.
The display returns to idle following successful
transfer.
Transferring with consultation
You can announce a call to a recipient before transferring it.
Prerequisite: You are conducting a call. The options "Allow Call Transfer" and "Transfer on Ring" were selected
(! page 89).
Consultation?
l
Select and confirm the option shown. The call is placed
on hold.
j Enter the phone number of the party to whom you want
to transfer the call.
Dial
Confirm.
If the party answers:
Announce the call you want to transfer.
Complete Xfer?
88
f
Select and confirm the option shown.
Enhanced phone functions
Step by step
If the party does not answer:
You do not have to wait for the second party to answer
before you can transfer the call.
Replace the handset or, if speakerphone mode is active,
press the lit n key to transfer the call.
If the party does not answer, you will be called back by
the first party.
Allowing call transfer
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Allow call transfer = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
89
Enhanced phone functions
Step by step
Allowing "Transfer on Ring"
If this option is allowed, you can activate call transfer by
replacing the handset even before the called party answers.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Transfer on ring = No
m
Select and confirm the option shown.
Yes
l
Confirm the option shown to activate the callback function.
Save & exit
l
Select and confirm the option shown.
90
Enhanced phone functions
Step by step
CTI calls
Beep on auto-answer
Speakerphone mode automatically activates on your
phone if you use a CTI application such as Outlook to
dial a number when Auto-answer is active. If Auto-answer is not active, the phone rings first and you have to
press the loudspeaker key or lift the handset to set up
the call. This setting also defines whether or not incoming calls are automatically accepted. If the function is
active, an alert beep sounds when an incoming call is
automatically accepted.
Information on the operation of the configured CTI application can be found in the corresponding user guide.
z You can also configure this setting via the Web interface
! page 178.
Prerequisite: The option was programmed by your service personnel.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Incoming calls?
Select and confirm the option shown.
CTI calls?
f
Select and confirm the option shown.
AutoAnswer = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
AutoAnswer beep = No
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
91
Enhanced phone functions
Step by step
Beep on auto-reconnect
You can reconnect a held call both via the CTI application and via the phone. A beep sounds when you toggle
between an active call and a held call when the function
is active.
Prerequisite: The option was programmed by your service personnel.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Incoming calls?
Select and confirm the option shown.
CTI calls?
f
Select and confirm the option shown.
AutoReconnect beep = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
92
Enhanced phone functions
Step by step
Making calls
Dialing with the DDS key
You can program frequently used phone numbers on
programmable keys (! page 66). If you press a direct
destination selection key briefly, the associated contact
or phone number appears and dialing is initiated.
Prerequisite: A direct destination key is programmed
! page 66.
R Press the programmed DDS key. Dialing is initiated.
Dialing a phone number from a list
The following call lists are available in the "Calls" directory:
• Missed
• Dialed
• Received
• Forwarded
For a detailed description of the call lists, see
! page 28.
O Press the key shown.
Calls
m
Select and confirm the option shown.
Dialed
f
Select and confirm the option shown.
Niels, Bohr
30.05. 07:06am
Select and confirm the appropriate list entry.
The phone number associated with the list entry is dialed. If you have not already lifted the handset, conduct
the call now in speakerphone mode.
93
Enhanced phone functions
Step by step
Using autodial delay
A number is automatically dialed after a set delay starting from the entry of the number’s last digit. The autodial delay can be used:
• when dialing in idle mode
• Consultation
• when transferring an answered call.
The delay can be reduced by performing one of the following activities:
= • Pressing the key =. This always works.
^ • lifting the handset. This only works if the phone number was entered when the phone was idle or if it was
entered for a consultation call when the handset was
off hook.
n • pressing the loudspeaker key. This only works if the
phone number was entered when the phone was
idle and the loudspeaker key was not lit or if the
phone number was entered for a consultation call
and the loudspeaker key was not lit.
If an emergency number is preset by your service personnel, the autodial delay for this phone
number is reduced to one second.
Automatic dial delay does not work if you are using a dial plan and Immediate dialing is configured (see ! page 47). The number is automatically dialed as soon as the string entered
matches an entry in the dial plan.
94
Enhanced phone functions
Step by step
Settings for autodial delay
The setting does not affect automatic emergency
number dialing.
If you select Autodial delay, you must either confirm
the "Dial" option, press the loudspeaker key or wait until
the autodial delay expires to set up a call when dialing
with the handset on hook.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Autodial delay = 8
f
Select and confirm the option shown.
j Enter a value in the input mask and confirm.
Save & exit
l
Select and confirm the option shown.
95
Enhanced phone functions
Step by step
Allowing "Busy When Dialling"
If you activate this function, an incoming call received
while you are performing dialing is rejected. The caller
then hears the busy signal.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Busy when dialing = No
m
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
96
Enhanced phone functions
Step by step
Conference
Local conference
This type of conference is also referred to as a threeparty conference. It involves up to three participants.
Prerequisite: You are conducting a consultation call
! page 50 or have accepted a second call ! page 83,
and the conference function is active ! page 98.
Initiating a local conference
Conference?
Select and confirm the option shown in the menu. You
are connected to both parties at once. Alternatively you
can press an already configured Conference key.
Conducting one-on-one calls
1: Party
f
On the display, select and confirm the first connection
you want to clear down.
or
2: Party
m
On the display, select and confirm the second connection you want to clear down.
Disconnect?
l
Select and confirm the option shown. You are now involved in a one-to-one call with the remaining call party.
{ or }
If you already are involved in a secure connection
with a party when you initiate a consultation call,
the original party is placed on hold. The new consultation connection can be either secure or nonsecure. However, the first connection remains
secure even if all three parties are now joined together in a conference.
The entire conference is nonsecure if the connection to at least one of the parties is not secure
(see also ! page 32).
The relevant padlock icon appears on the "Conference" row.
97
Enhanced phone functions
Step by step
Ending a local conference
Allowing call partners to continue a conference after you exit
Prerequisite: The "”Allowing joining in a local conference” ! page 99" function is activated.
Exit Conf?
l
Select and confirm the option shown in the menu. Both
call partners remain connected. You are disconnected
from the conference call.
or
^ or n Replace the handset or, if you are in speakerphone
mode, press the loudspeaker key. Both call partners remain connected. You are disconnected from the conference call.
Disconnecting a party
End Conf?
f
Select and confirm the option shown in the menu.
Both connections are cleared down – the conference is
cleared down.
Allowing a local conference
This option allows or blocks the "Conference" function.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Allow conferences = No
m
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
98
Enhanced phone functions
Step by step
Allowing joining in a local conference
You can use this option to decide whether or not your
call partners are allowed to join calls after you exit the
conference call.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Allow exit conf = No
m
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
99
Enhanced phone functions
Step by step
System-based conference
This type of conference is also referred to as a large conference. It can include up to ten parties.
Prerequisite: You are conducting a consultation call
! page 50 or you have accepted a second call
! page 83, and the "System conference" feature was
configured by your service personnel.
Establishing a conference
Conference?
f
Select and confirm the option shown in the connection’s context menu. You are connected to the first two
parties at once. The conference is displayed with the
current participants. You can now:
• initiate a consultation call
• put the conference on hold
• leave the conference.
Conducting a consultation call
Consult?
f
Select and confirm the option shown in the "Conference" context menu. If the party answers, you can:
• toggle between the party and the conference
• connect the consultation call to another called party
• end the consultation call and return to the conference
• add the consultation call party to the conference.
If you intend to include the consultation call party
in the conference, you can also use the
"Hinzufügen zu Konferenz" option instead of the
"Consultation" option.
If you want to use a call list for the consultation,
select Hold in the context menu instead of
Consult (or Hinzufügen zu Konferenz) or press
the Hold key and then select the required call list
(! page 102).
Alternatively you can select a call list without
using the Hold functions - the conference call is
automatically placed on Hold.
Add party
Prerequisite: You are conducting a consultation call and
the conference is on hold.
100
Enhanced phone functions
Step by step
Conference?
f
Select and confirm the option shown in the consultation
call’s context menu. The party is added to the conference. Only the conference and all current participants
are now displayed. You can scroll through the list of participants.
You can also use an already configured
Conference key instead of the Conference
option in the context menu.
Putting the conference on hold
Hold?
f
Select and confirm the option shown in the "Conference" context menu. The conference is placed on hold
and you can consult with someone in your office, for instance.
Leaving a conference
Exit Conf?
f
{ or }
Select and confirm the option shown in the "Conference" context menu. You are disconnected from the
conference call and can dial another number, for instance. The other call partners remain connected.
If using the "System conference" option, the Conference line contains a closed padlock icon for a
secure voice connection and an open padlock
icon for a nonsecure voice connection
! page 32).
The display depends on whether the conference
server supports secure voice communication.
The appropriate display is set by the conference
server.
101
Enhanced phone functions
Step by step
Call lists
For a detailed description of the different call lists, see
! page 28.
Dial entry
O Press the key shown.
Calls
m
Select and confirm the option shown.
Missed
l
For instance, select and confirm the list of missed calls.
The list is sorted chronologically, with the most recent
caller first.
You can use the Navigator keys to browse through the
list.
Niels, Bohr
13:22
Select and confirm the appropriate list entry. The phone
number is dialed.
Delete all entries
O Press the key shown.
Calls
m
Select and confirm the option shown.
Dialed
l
For instance, select and confirm the list of dialed numbers.
Delete All
l
Select and confirm the option shown. All entries in the
list displayed are deleted.
102
Making calls with multiple lines
Step by step
Making calls with multiple lines
You can use your OpenStage 20 E as a multi-line phone.
If you have any questions regarding how to configure
your OpenStage phone as a multi-line phone, please
contact your service personnel.
The following is a description of the telephony scenarios for multi-line phones. To facilitate comprehension,
you should familiarize yourself with the enhanced telephony application and how to use the line keys beforehand. You can make further individual settings for your
multi-line phone. Refer to the following sections for a
detailed description of the individual components:
• Introduction to multi-line phones ! page 13
• Lines and line keys ! page 20
Incoming calls
Depending on your individual settings, you will be notified of incoming calls ! page 155.
Accepting calls for the primary line
In this case, the telephone behaves in the same way as
a single-line telephone. See ! page 32 and ! page 75.
Accepting calls for secondary lines
Prerequisite: The secondary line is configured on your
multi-line telephone.
Using the handset
^ Lift the handset.
[ Conduct call.
The line used for the ringtone is selected automatically. If there are calls on several lines, you
are connected with the line that has been ringing
the longest.
103
Making calls with multiple lines
Step by step
Using the line keys
T Press the flashing line key. Speakerphone mode.
or
Accept?
l
Confirm. Speakerphone mode.
Making calls
You must seize a line before you can make calls on a
multi-line telephone.
Trunk seizure can be configured on an individual basis.
Your service personnel can determine if the lines on
your telephone can be automatically seized and with
which priority.
If you have seized a secondary line, this line is
reserved for you for making calls for a specific
period as defined by the service personnel. No
other user can seize this line during this period,
even if the line is also assigned to this user’s
telephone.
Manual trunk seizure
^ or n Lift the handset or press speakerphone key.
S Press the required line key.
j Enter the phone number or use redial, for example. The
connection is set up.
Automatic trunk seizure
Prerequisite: Your service personnel has configured
automatic trunk seizure.
^ or n Lift the handset or press speakerphone key.
R The line defined during configuration is seized.
j Enter the station number. The connection is set up.
104
Making calls with multiple lines
Step by step
Dialing the last dialed number
Regardless of the line used, the last number dialed on
your telephone is displayed for redialing in the selected
number’s context menu.
^ or n Lift the handset or press speakerphone key.
S Press the required line key (! page 104).
Redal is offered on the display as long as a number has
been dialed previously:
Redial {1} 12345?
l
Confirm. The connection is set up.
Forwarding calls for primary line
The call forwarding can only be activated for the primary
line. Which call forwards are possible, how they are configured and activated can be found from ! page 54.
Call forwarding information
Prerequisite: Your service personnel has activated "Forwarding shown".
If you have activated one of the forwarding types on
your phone for the primary line and a station calls, a
popup window with the following information opens:
• Who is calling
• The forwarding destination.
105
Making calls with multiple lines
Step by step
During calls
Making and receiving calls on a single line
If you only use one line on your multi-line telephone to
make calls, and you receive calls on the same line, the
phone operates in the same way as a single-line telephone:
• Redial ! page 49
• Consultation ! page 50
• Alternate ! page 51
• Callback! page 62
• Hold ! page 79
• Call waiting (second call) ! page 83
• Transferring a call ! page 88
• Conference ! page 97
Functions available exclusively for the primary line:
• Call lists ! page 28
• Voicemail ! page 28
• Call forwarding ! page 54
• Do not disturb ! page 121
Depending on your individual settings, you will
be notified of incoming calls ! page 154.
Making and receiving calls with multiple
lines
Accepting a waiting call
Depending on the settings for "Rollover", you will
be notified of incoming calls ! page 119.
Prerequisite: You are conducting a call. At the same
time, a call is incoming on another line.
[ Call on line 1.
T Press the line key for line 2. The call on line 1 is placed
on hold.
106
Making calls with multiple lines
Step by step
All multi-line users that share the line on which
the call is being held (! page 20) can now pick
up the held call. To prevent other users from answering the held call, you must place the call on
"Consultation" hold ! page 50.
Depending on the setting made by your service
personnel, you may have to press the trunk key
twice to accept the call on the other line. The first
call is either placed on hold or released depending on the setting.
[ Conduct call on line 2.
\ End call on line 2.
T Press line key for line 1.
[ Retrieve call on line 1.
Putting a line on hold
On a multiline telephone you can use the line keys to
place calls on hold.
Prerequisite: You are conducting a call.
R Press the call-line key.
T • The LED line key flashes.
•
•
The LED line displays the hold status on all multi-line
phones to which the line is connected.
On phones connected to the line, a user can press
the relevant line key and accept the held call.
During a consultation call or after accepting a waiting
call the hold function cannot be used.
107
Making calls with multiple lines
Step by step
Lines with hot or warm line function
Your service personnel can configure a hot or warm line
for the primary and secondary line.
The function is activated when on
• The Primary line
you pick up the phone’s handset or press the line or
loudspeaker key
• the secondary line
you press the line key.
A number specified by you is dialed with a hot line immediately and with a warm line after a specific time.
Examples:
• The phone in the lift immediately dials the reception
number.
• The phone at a patient’s bed dials the ward number
e.g. after a minute if no other number is dialed.
Entering a number for the hot and warm line function
Specify which number should be dialed when the hot or
warm line function is activated.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Keyset
Select and confirm the option shown.
Lines?
Select and confirm the option shown.
Line
f
Select and confirm the line you want.
Hot warm dest? = nnnn
f
Select and confirm the option shown.
108
Making calls with multiple lines
Step by step
j Enter and confirm the destination.
Save & exit
l
Select and confirm the option shown.
Busy override
A station of a line trunk group is on a call. It’s primary
line is configured as a secondary line on your phone.
This line now has the status "busy." You can join in the
call by pressing the illuminated key of this line (see also
! page 20).
Prerequisite: A secondary line is configured on your
multiline phone and busy override is enabled for you.
The key of secondary line illuminates – it is busy. You
want to join in the call.
R Press the lit key. A conference is established. You are
connected to the parties on the secondary line. The key
continues to illuminates and the conference is shown
on the display.
If there is already a conference on the secondary
line you are connected to this conference. The
conference is shown on the display.
You can now:
• Put the secondary line on hold
• Leave the conference on the secondary line
• Make consultation call
• Accept a second call
• Alternate between a new call party and a conference on the secondary line.
• Include a call party from a consultation or a second
call in the conference.
109
Making calls with multiple lines
Step by step
Direct station selection keys
Apart from line keys, service personnel can also configure direct station selection (DSS) keys. You can use a
DSS key to call an internal station directly, pick up calls
for this station or forward calls directly to it.
Calling a station directly
You cannot use DSS if the user is on another call (flashing LED).
Calling from the idle menu
S Press the relevant DSS key.The key lights up and a connection is established.
Service personnel can configure the DSS key so
that the connection is also established when the
DSS station has activated do-not-disturb or call
forwarding.
Consultation with the DSS station
Prerequisite: You are conducting a call and service personnel have configured the DSS key for consultation.
S Press the relevant DSS key for the consultation. The key
lights up and a connection is established.If the station
answers, you can toggle, transfer the first call or initiate
a conference.
If service personnel have configured transfer instead of consultation, you can only transfer the
current call to the DSS station.
110
Making calls with multiple lines
Step by step
Call pickup
You can pick up calls for another DSS station. If a call is
waiting on their line, the LED flashes.
Indirect pickup
Prerequisite: The auto-answer function must be deactivated ! page 91.
T Press the DSS key. The call is routed to your primary line
and rings.
^ or n Lift the handset or press speakerphone key. You are
connected with the other party.
Rejecting a call
Prerequisite: Service personnel must activate the reject option for DSS keys and auto-answer must be deactivated ! page 91.
T Press the DSS key. The call is routed to your primary line
and rings.
Reject
f
Select and confirm the option shown in the pop-up
menu.
The caller hears a busy signal.
Direct pickup
Prerequisite: The auto-answer function must be activated ! page 91.
T Press the DSS key. The call is routed to your primary line
and you are immediately connected with the other party via speakerphone.
111
Making calls with multiple lines
Step by step
Deflecting a call to a DSS station
Prerequisite: The deflect function must be approved
for DSS keys. For information on the current setting,
see ! page 76.
If you receive a call on one of your lines, you can immediately deflect it to the DSS station.
T Your phone rings and a line key flashes.
S Press the relevant DSS key. The call is deflected to the
DSS station. If the DSS station does not answer, you
can pick up the call by pressing the DSS key.
LED display on DSS keys
112
DSS Key
Explanation
S
Off: The line is in idle mode.
T
Flashes: You can accept a call for the DSS
station via the key. The call is routed to
your primary line when the call is accepted.
R
Illuminates: The line is busy. Provided
that second call is activated you can still
reach the DSS station via the key. It can
accept your call as a second call.
Making calls with multiple lines
Making calls in an executive-secretary team
An executive-secretary team is configured by the relevant service personnel and may include up to four executive and up to two secretary telephones.
Sample scenarios
This example assumes that two executive and two secretary phones are
configured. Calls for the executives are forwarded immediately to the respective secretary phone. A secretary then connects the call with or without consultation to the responsible executive using the direct station selection key.
Secretary 1
Secretary 2
Line
Line
Executive 1
Executive 2
Secretary 2
Call waiting
Executive 1
Executive 2
Secretary 1
Call waiting
Shift
Executive 1
Line
Shift
Executive 2
Line
Secretary 1
Secretary 2
Secretary 2
Secretary 1
Shift
Shift
Prerequisites:
The following call forwards are configured (! page 54 ):
• For All calls from Executive 1 to Secretary 1
• For All calls from Executive 2 to Secretary 2
• Forward on Busy and forward on No reply from Secretary 1
to Secretary 2
• Forward on Busy and forward on No reply from Secretary 2
to Secretary 1
"Allow call waiting" should be activated on the secretaries’ phones
(! page 86). This function can optionally be activated and deactivated using a key if a key has been configured for it.
Line and direct station selection keys have been configured by service personnel and "Transfer on hangup" and server features have been activated.
113
Making calls with multiple lines
Step by step
Accepting a call
Incoming calls for the executives should be forwarded
immediately to the assigned secretary and answered
there.
Accepting calls at the secretary phone
An incoming call for "Executive 1" rings at the assigned
"Secretary 1".
The line key of the "Secretary 1" phone flashes.
The "Secretary 1" direct station selection key on
the "Executive 1" phone also flashes.
T Press the line key to answer the call. The station answers. The line key flashes rapidly.
The "Secretary 1" direct station selection key on
the "Executive 1" phone illuminates.
Early call pickup by Executive 1
An incoming call for "Executive 1" rings on "Secretary 1".
The "Secretary 1" direct station selection key on the "Executive 1" phone flashes. The "Secretary 1" has not yet
answered the call. Before the call is forwarded to
"Secretary 2", "Executive 1" picks up the call early.
T Press the "Secretary 1" direct station selection key on
the "Executive 1" key to answer the call.
If for example a call for "Executive 2" on
"Secretary 2" is not answered, "Secretary 1" or
"Executive 1" can pick up the call early
114
Making calls with multiple lines
Step by step
Forward to Secretary 2
An incoming call for "Executive 1" rings at the assigned
"Secretary 1" . The call is not answered. After a specified period the call is forwarded to "Secretary 2". The
line key of the "Secretary 2" flashes and it rings.
T Press the line key on the "Secretary 2" phone to answer
the call. The station answers. The "Secretary 2" direct
station selection key on the "Executive 1" phone illuminates.
If "Secretary 1" is busy, the call is forwarded immediately to "Secretary 2" if:
• a consultation call is being made or
• "Allow call waiting" is deactivated.
Second call
If "Secretary 1" receives a second call, this can be accepted, ignored, forwarded or rejected. Detailed information on this can be found from ! page 83.
If the second call is ignored, it is forwarded to
"Secretary 2" after a certain period of time.
If the second call was answered, it can be forwarded using consultation or the direct station selection keys.
Connecting a call
If e. g. the "Secretary 1" answered a call, it can forward
the call using the direct station selection keys to the following telephones:
• Executive 1
• Executive 2
• Secretary 2.
The following examples show connections to "Executive 1".
Connecting with consultation
S Press the DSS "Executive 1" key. "Executive 1" answers.
Announce the call.
\ or n Hang up or press the loudspeaker key.
You can also select "Complete Xfer" from the context ment.
115
Making calls with multiple lines
Step by step
Connecting without consultation
S Press the DSS "Executive 1" key. "Executive 1" does not
answer.
Complete transfer
f
Select and confirm the option shown in the pop-up
menu.
\ or n Hang up or press the loudspeaker key. The "Executive 1"
phone rings.
If "Executive 1" does not answer the call, so erfolgt ein
Wiederanruf ( see also ! page 88) nach einer eingestellten Zeit.
The "Executive 1" direct station selection key on
the "Secretary 1" phone illuminates.
Consultation without connecting
S Press the DSS "Executive 1" key. "Executive 1" answers.
Transferring is not required. The "Secretary 1" takes the
call back
Disconnect & return?
f
Select and confirm in the options menu. The
"Secretary 1" is reconnected with the caller.
Toggle, disconnect or conference
During a consultation call "Secretary 1" can toggle between "Executive 1" and the caller, can initiate a conference or disconnect one of the two call parties. More on
this subject can be found on pages ! page 51 and
! page 97.
DSS keys can be used
These keys are configured in such a way that every
phone can be reached by every phone in the group. The
DSS keys are also used for consultation calls.
S Press a team member’s DSS key. The relevant phone
rings and the party answers.
116
Making calls with multiple lines
Step by step
Settings for MultiLine (keyset)
The details for each keyset line contain supplementary
information for the user. The following uneditable fields
are displayed:
• Address
– Displays the phone number for the line
• Ringtone on/off
– Displays whether this line’s ringtone is active
• Selection sequence
– Displays the priority of each line seizure when the
handset is lifted or the loudspeaker key for this
line is pressed
Setting the time for a delayed ringer
Specify the length of time before a held call should be
signaled on a line.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Keyset
Select and confirm the option shown.
Lines
Select and confirm the option shown.
Line 1
f
Select and confirm the required line (for example, line
1).
Ring delay
f
Select and confirm the option shown.
j Enter and confirm a delay value.
Save & exit
l
Select and confirm the option shown.
You can activate and deactivate the set delay time for all
line keys using a function key ! page 73.
117
Making calls with multiple lines
Step by step
Line preview
Activating via the line keys
Prerequisite: You are already on a call on one line and a
further call rings on the secondary line. Service personnel have activated line preview.
T Press the flashing line key. A popup window opens and
you receive information about the caller.
T Press the flashing line key to answer the second call.
If service personnel have deactivated the line
preview, a call is answered immediately on a second line when the line key is pressed, without
showing caller information.
Activating via preview key
Prerequisite: You have programmed a key with the
"Preview" function ! page 66. Your service personnel
have activated the preview function.
Preview for a call:
You are already conducting a call on one line. A further
call rings on a secondary line.
S
Press the "Preview" key. A popup window opens and
you receive information about the caller.
R Press the "Preview" key again to hide the preview or
wait until the popup closes itself after a specified period
of time.
Permanent preview
S Press the "Preview" key in idle mode. This way the preview for all lines with "preview mode" remains active until you press the "Preview" key again.
118
Making calls with multiple lines
Step by step
Rollover for a line
Your service personnel can determine how rollover calls
are to be signaled.
T Only the relevant line key blinks.
or
Z T You hear a special advisory tone via the currently acor
tive microphone and the corresponding line key blinks.
Z T The ringer melody set sounds briefly (approx.
or
3 seconds) via the loudspeaker and the corresponding
line key blinks.
Z T You hear a short notification tone
The ringer melody is not played in speakerphone
mode.
Z T k The telephone rings using the configured call signal, the
corresponding line key blinks, and a pop-up menu containing the available information is displayed.
119
Privacy/security
Step by step
Privacy/security
Deactivating the ringer
You can deactivate your ring tone if you do not want to
be disturbed by your phone ringing.
) Hold down the key in idle mode until the "Ringer off"
icon appears on the display.
or You can also deactivate the function using the option in
the idle menu (! page 24).
Ringer off
f
Select and confirm the option shown.
Reactivating the ringer
) Hold down the key in idle mode until the "Ringer off"
icon disappears from the display.
The ringer is reactivated.
or You can also activate the function using the option in the
idle menu (! page 24).
Ringer on
f
Select and confirm the option shown.
or
Deactivating the ringtone with a key
Prerequisite: The "Ringer off" key must be programmed (! page 66).
S Press the "Ringer off" key.
An incoming call is signaled by a single ring tone burst.
R Press the illuminated key once more to deactivate the
"Ringer off" function.
120
Privacy/security
Step by step
Do not disturb
If "Do not disturb" is activated, your telephone will not
ring. The caller hears the busy signal. The "Do not disturb" function is activated/deactivated via the idle
menu.! page 24
On multi-line telephones (! page 13) you can
only activate the "Do not disturb" function for
your primary line.
Prerequisite: A programmable key is assigned the
function "Do Not Disturb" (see ! page 66). "Do not disturb" must be activated (! page 122).
Enabling do not disturb via a key
S Press the "Do not disturb" programmable key.
R Press the lit programmable key once more to deactivate
the "Do not disturb" function.
You can also use the programmable key to activate the "Do not disturb" function during a call or
deactivate it when an incoming call is being signaled.
or
Enabling do not disturb via the idle menu
Do not disturb on
f
Select and confirm the option shown in the idle menu.
The "Do not disturb" icon appears ! page 25.
or.
Do not disturb off
f
Select and confirm the option shown. The do not disturb icon is deleted.
121
Privacy/security
Step by step
Allowing "Do not disturb"
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Configuration
Select and confirm the option shown.
Incoming calls?
Select and confirm the option shown.
Handling?
f
Select and confirm the option shown.
Allow DND = No
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
122
Privacy/security
Step by step
Security
User password
Your User password protects your individual configurations, including your language settings. You can also use
the User password to lock your telephone ! page 126.
Service personnel may have configured the following settings:
• The password is deactivated: You do not have the
option of configuring user settings. The message
"Password is disabled" is displayed.
• The password is temporarily blocked: You do not
have the option of configuring user settings at this
time. The message "Password.suspended" is displayed.
• After initially logging onto a user area, you may have
to replace the default password with a new password.
• A password can have a predefined period of validity:
You will have to create a new password when the
period ends. The message "Change Password ({1}
days left)" will alert you to this at the appropriate
time. The message "Password has expired" appears
when the validity period is over. Confirm "Change
password" and change the password as described
in this section.
• If you repeatedly enter the wrong password (2 to 5
times), additional attempts are blocked. You can
make another attempt after a predefined time.
• It is possible that you will not be able to re-use a previously used password for a long time, so you will
have to create another "new password". The message "Password requires change" is displayed. This
does not affect deactivation of the user password
! page 125.
• Your service personnel can tell you about the rules
for what and how many characters can or must be
used in the password.
The preset password "000000" corresponds to a
blank password. In other words, the phone cannot be locked and the user menu is not password-protected (see also ! page 125)
z The User password can also be modified via the Web interface ! page 178.
123
Privacy/security
Step by step
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Security?
Select and confirm the option shown.
Change user password
l
Select and confirm the option shown.
Current password
l
Select and confirm the option shown.
j Enter the current password (at least six characters, text
entry, see ! page 22) and confirm your entry.
New user password
f
Select and confirm the option shown.
j Enter a new password (at least six characters) and confirm (text entry, see ! page 22).
Confirm new user password
f
Select and confirm the option shown.
j Enter the new password again and confirm with OK.
Save & exit
124
l
Select and confirm the option shown.
Privacy/security
Step by step
Deactivating the user password
You can deactivate the phone’s password prompt if a
password has already been configured.
The deactivation of the password prompt does
not affect the Web interface ! page 178 or
CTI applications that use a password prompt.
As long as the user password is deactivated, you
do not have access to user settings via the Web
interface.
If you deactivate the user password, you are not
able to lock the phone ! page 126 and the user
menu is not password-protected.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Security?
Select and confirm the option shown.
Change user password
l
Select and confirm the option shown.
Current password
l
Select and confirm the option shown.
j Enter the current password (at least six characters, text
entry, see ! page 22) and confirm your entry.
New user password
f
Select and confirm the option shown.
j Enter six zeros ("000000") to deactivate the password.
Confirm entry (at least 6 characters, (text entry, see
! page 22).
Confirm new user password
f
Select and confirm the option shown.
j Enter six zeros ("000000") to deactivate the password
(for text input, see ! page 22) and confirm.
Save & exit
l
Select and confirm the option shown.
125
Privacy/security
Step by step
Phone locking
You can lock your phone to protect it against unauthorized access. In this way, no one can make calls or
change your user settings unless they know your user
password.
If an emergency number has been entered on the
phone by service personnel, "emergency call" is then offered as an option on the display when the lock is activated. You can also enter the emergency number via
the keypad.
You can only lock the phone if you set a user
password (! page 123). The password for this
must not be the default setting "000000".
Check if necessary whether the telephone lock
function has been activated for you by service
personnel.
Activating the phone lock
( Hold down the key shown.
Confirm lock?
Confirm. The "Locked phone" icon appears on the display ! page 25.
or
N Press the key shown.
User
Select and confirm the option shown.
j Enter and confirm the user password.
Security?
Select and confirm the option shown.
Phone lock?
f
Select and confirm the option shown.
Phone lock = No
l
Select and confirm the option shown.
Yes
l
Select and confirm the option shown.
Save & exit
l
Select and confirm the option shown.
The phone is locked.
126
Privacy/security
Step by step
If an emergency number has been entered on
the telephone by service personnel, Emergency
call will be offered on the display once you have
activated the phone lock. You can also dial the
emergency number via the keypad.
Unlocking the phone
The following is displayed: Phone locked.
There are two options available for unlocking the phone:
• User unlock
• Admin unlock
Select and confirm if you know the user password. You
are prompted to enter the user password.
User unlock?
or
Admin unlock?
Select and confirm if you only know the administrator
password. You are prompted to enter the administrator
password.
j User password or enter and confirm the administrator
password. The phone is unlocked if the password is correct.
If the telephone is locked, an emergency number
entered by service personnel can be dialled using
the keypad or the option Emergency call.
If the telephone is locked repdial keys cannot be
used. This also applies if the emergency number
is saved on it.
127
Mobility
Step by step
Mobility
Prerequisite: Your phone is configured to support mobility by service personnel. A DLS server is available in
the LAN and its address is entered in the phone.
Mobility scenarios
When you log on to your phone, or any other mobilityenabled phone, the following scenarios are possible:
Logging on and off at the same phone
•
•
Log on as a mobility user ! page 129.
Log off as a mobility user ! page 130.
Logging on and off at different phones
In these cases, service personnel may have made the
following settings:
• Log on at a remote phone with forced logon, when
the user is still logged on at that phone ! page 131.
• Delayed logon at a remote phone with forced logon,
when the user is still logged on at that phone and
the phone is busy ! page 132.
128
Mobility
Step by step
Logging on and off at the same phone
Logging on to the phone
Prerequisite: No other mobility user is logged on.
Logon via a key
If a program key is configured for Mobility.
S Press the "Mobility" program key.
or Logon via the context menu
Mobile logon?
f
Select from the idle display context menu (! page 24)
and confirm.
The Mobility logon dialog appears.
Mobility ID
You are prompted to enter your mobility ID.
j Enter and confirm Mobility ID, usually a telephone number.
Enter password
You are prompted to enter the password.
j Enter and confirm the user password.
The following messages appear on the display:
• Logging on mobile user
• Validating
• Registering
• Downloading user data
Once you have completed logon, the mobility icon is
shown in the display.
.
129
Mobility
Step by step
Logging off from the phone
Prerequisite: You are logged on as a mobility user.
Logoff via key
If a program key is configured for Mobility.
R Press the "Mobility" program key.
or Logon via the context menu
Mobile logoff?
Mobile logoff
f
Select and confirm! page 24 the option shown in the
idle display context menu.
Is displayed. You briefly have the option to cancel the
logoff, otherwise the logoff process is launched.
In the graphic display, the following messages appear:
• Logging off mobile user
• Uploading user profile
• Registering
• Downloading user data
After you have logged off, the mobility icon
den.
130
is hid-
Mobility
Step by step
Logging on at different telephones
An attempted login is rejected if the user is already
logged on to another phone and "Logon with forced
logoff" is disabled for the mobility user.
Logging on with forced logoff at a remote
phone
If the user is already logged on at another phone and
the remote phone is busy, the logon is rejected.
If however, your service personnel enabled "Forced
logoff during call" without setting a time, the system
does not consider whether or not the remote phone is
busy.
Logon via a key
If a program key is configured for Mobility.
S Press the "Mobility" program key.
or Logon via the context menu
Mobile logon
Select and confirm the option shown in the idle display
context menu ! page 24.
Mobility ID
You are prompted to enter your mobility ID.
j Enter and confirm Mobility ID, usually a telephone number.
Enter password
You are prompted to enter the password.
j Enter and confirm the user password.
The following mobility messages appear in the display:
• Validating
• Logging off elsewhere
• Registering
The logoff is simultaneously displayed on the remote
phone. Once logon is complete, the "Mobility" program
key LED lights up and the mobility icon appears in the
display
.
131
Mobility
Step by step
Logging on with forced, delayed logoff at a
remote- phone
If the remote phone is busy and your service personnel
enabled "Forced logoff during call" with a set timeout,
forced logoff does not occur until this timeout expires.
Logon via a key
If a program key is configured for Mobility.
S Press the "Mobility" program key.
or Logon via the context menu
Mobile logon
Select and confirm the option shown in the idle display
context menu ! page 24.
Mobility ID
You are prompted to enter your mobility ID.
j Enter and confirm Mobility ID, usually a telephone number.
Enter password
You are prompted to enter the password.
j Enter and confirm the user password.
The following mobility messages appear in the display:
• Validating
• Logging off elsewhere
At the same time, the display on the busy remote phone shows "Forced logoff pending".After
the set timeout the active call is ended and remote logoff is performed.
•
•
Registering
Downloading user data
Once logon is complete, the "Mobility" program key
LED lights up and the mobility icon appears in the display
.
132
OpenScape Voice functions
Step by step
OpenScape Voice functions
The OpenScape Voice supports a number of functions
that you can activate and deactivate from your phone.
On multi-line telephones, the full scope of
OpenScape Voice functions is only available for
the primary line.
Feature toggle key
You can pick a programmable key and program it as a
feature toggle key for activating the "make line busy"
and "stop hunt" functions.
You can then use the programmable key to activate or deactivate the relevant OpenScape Voice function on the
server for this phone.
You can only program first-level programmable keys because those linked to LEDs are used to display the function status as either on (LED on) or off (LED off). The
LED indicates the status of the function on the server
and can therefore change without any of the programmable keys being pressed.
Example:
Switching between "Line busy" and "Line free" (see also
! page 140).
S
Prerequisite: Your service personnel configured a programmable key with the function "Busy" ("make line
busy" for the hunt group) ! page 70.
Press the programmable key – the key lights up.
R Press the illuminated programmable key once again to
release the line - the keys stops illuminating.
133
OpenScape Voice functions
Step by step
Making anonymous calls
Your service personnel decides whether or not your caller ID (name and phone number) is displayed on a called
party’s station. Anonymous calling is when your data is
not transmitted. The settings configured can be deactivated, however, for specific calls.
•
•
If your caller ID is transmitted: your caller ID is
displayed.
If your caller ID is suppressed: "unknown" is
displayed.
Deactivating
If your service personnel permanently activated anonymous calling for your phone, you can deactivate this
setting as follows:
^ Lift the handset.
j Enter the code (see the table of codes ! page 148) to
transmit the caller information.
Z You hear a confirmation tone.
Activating
If your service personnel activated caller ID transmission for your phone, you can deactivate this setting as
follows:
^ Lift the handset.
j Enter the code (see the table of codes ! page 148) to
suppress the caller ID.
Z Wait until you hear the confirmation tone.
Caller ID transfer is suppressed. "Private/Anonymous"
appears on the called party’s display instead of the caller ID.
134
OpenScape Voice functions
Step by step
Temporarily activating anonymous calling for
the next call
If your service personnel activated caller ID transmission for your phone, you can deactivate this setting for
the next call as follows:
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Z Wait until you hear the confirmation tone.
j Dial the phone number of the party you want to contact.
Caller ID transmission is reactivated after this call.
Temporarily deactivating anonymous calling
for the next call
If your service personnel suppressed caller ID transmission for your phone, you can enable this setting for the
next call as follows:
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Z Wait until you hear the confirmation tone.
j Dial the phone number of the party you want to contact.
When you end this call, caller ID transmission is suppressed once again for the next call.
135
OpenScape Voice functions
Step by step
Creating a list for selective calls
For call acceptance
You can create a list of the phone numbers from which
you are willing to accept calls (also known as a selection
list). Your service personnel know how long this list may
be in the OpenScape Voice used on site in your facility.
A connection is set up if a caller’s phone number matches a number in the selection list. If there is a match:
• the caller receives a message that the party refuses
to accept any calls with this number,
or •
the call is forwarded to an external phone number.
Contact your service personnel for information on how
your OpenScape Voice is configured on site.
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Various announcements deliver the following information:
• the name of the feature (selective call acceptance)
• the current status (active or inactive)
• the current scope of the selection list.
These announcements are followed by verbal user
prompts that let you:
• add entries to the selection list
• delete entries in the selection list
• check the selection list
• activate or deactivate the function.
136
OpenScape Voice functions
Step by step
For call rejection
As for selective call acceptance, you can create a selection list with the phone numbers of parties from whom
you are not willing to accept calls. Your service personnel know how long this list may be in the
OpenScape Voice used on site in your facility.
A call is not connected if the caller’s phone number
matches a number in the selection list; the caller is notified that the called party rejects calls from this number. If the caller’s number is not in the selection list, the
call is to you as usual.
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Various announcements deliver the following information:
• the name of the feature (selective call rejection)
• the current status (active or inactive)
• the current scope of the selection list.
These announcements are followed by verbal user
prompts that let you:
• add entries to the selection list
• delete entries in the selection list
• check the selection list
• activate or deactivate the function.
137
OpenScape Voice functions
Step by step
Anonymous calls
Rejecting
You can reject all calls from parties that activated a data
protection feature (for example, caller ID suppression)
to prevent their phone number from being transmitted.
In this case, you are not informed that a call was rejected.
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Accepting
You can also accept calls from parties that activated a
data protection feature (for example, caller ID suppression) to prevent their phone number from being transmitted.
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
138
OpenScape Voice functions
Step by step
Using abbreviated dialing
Abbreviated dialing gives you access to a central list of
frequently dialed phone numbers.
You can dial a specific phone number by simply entering
a digit string. As these are three-digit numbers, you can
store up to 1000 phone numbers. This list is stored centrally and managed by your service personnel.
^ Lift the handset.
j Enter the code (see the table of codes ! page 148) followed by a number between 0 and 999 for the phone
number you want to dial.
The number is automatically dialed.
Call tracing
You can request automatic tracing of the last received
internal call. This is particularly suitable for identifying
malicious, irritating or troublesome calls.
n Lift the handset.
o Enter the code (see the table of codes ! page 148).
The phone number is determined. Ask your service personnel for the result.
139
OpenScape Voice functions
Step by step
Hunt group functions
To ensure optimum handling of specific calls, your telephone can be assigned to a pickup group ! page 39
and/or a hunt group.
Your service personnel can incorporate multiple telephones in a hunt group. If your telephone is assigned to
a hunt group, OpenScape Voice forwards calls for the
members of your group in accordance with specific
rules defined by your service personnel. Hunt groups
are a simple solution for distributing calls to a group of
telephones.
If you want another member of the group to pick up an
incoming call, you can set your telephone to signal the
busy status for your line to the other members of the
hunt group. Hunt group calls will then no longer be forwarded to your telephone.
Making a line busy
This prevents this line being used for calls in a hunt
group.
Activating
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Z Wait until you hear the confirmation tone.
Deactivating
Make the line free once more for the hunt group.
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Z Wait until you hear the confirmation tone.
140
OpenScape Voice functions
Step by step
Marking the last line in the hunt group chain
Sets the "stop hunt" line in the hunt group chain. The
system will stop looking for a free line in the hunt group
chain after it reaches this line.
Activating
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Z Wait until you hear the confirmation tone.
Deactivating
Unmark the line as the end of the hunt group chain.
^ Lift the handset.
j Enter the code (see the table of codes ! page 148).
Z Wait until you hear the confirmation tone.
141
OpenScape Voice functions
Step by step
Reachability
You can make either serial calls or simultaneous calls on
several sites. The features for this are
• Serial call
• Parallel call
Prerequisite: The service personnel has configured the
respective feature for your main number in OpenScape
Voice.
Serial call
Managing number lists/activating serial call
Before the serial call number can be activated, a serial
call list much be created. This can be prepared either by
service personnel or you can create it yourself later. Up
to six numbers can be entered in the list for sites on
which incoming calls including your main number
should be signaled sequentially. Each number can consist of up to 30 digits.
^ Lift the handset.
j Enter the code for the edit mode (see code table
! page 148).
The edit mode opens and you hear an announcement
with the following information:
• Feature name
• Current status (active/inactive)
• Number of numbers currently on the serial call list
You are prompted to do one of the following:
• Activate/deactivate the feature (only if numbers are
already entered in the list)
• Call up the numbers currently entered in the list.
• Add or delete numbers
• Repeat the options in edit mode
If the serial call list is still empty, you are prompted to
enter numbers in the list. As soon as you have entered
a valid number, the serial call can be activated.
If the serial call is activated, incoming calls are first routed to your phone. If you do not answer within the timeframe defined by the service personnel, the next destination phone rings for the configured period of time.
142
OpenScape Voice functions
Step by step
The caller is informed that the call is being routed to another station. The connection is established with the
first phone that accepts the call.
If the call is not answered by any phone, it is forwarded
to the configured forwarding destination (on no reply) or
to a "rejection announcement".
Parallel call
Managing number lists/activating parallel call
Before the parallel call feature can be activated, a parallel call list must be created. This can be prepared either
by service personnel or you can create it yourself later.
Up to six numbers can be entered in the list for sites on
which incoming calls including your main number
should be signaled sequentially. Each number can consist of up to 30 digits.
^ Lift the handset.
j Enter the code for the edit mode (see code table
! page 148).
The edit mode opens and you hear an announcement
with the following information:
• Feature name
• Current status (active/inactive)
• Number of numbers currently on the parallel call list
You are prompted to do one of the following:
• Activate/deactivate the feature (only if numbers are
already entered in the list)
• Call up the numbers currently entered in the list.
• Add or delete numbers
• Repeat the options in edit mode
If the parallel call list is still empty, you are prompted to
enter numbers in the list. As soon as you have entered
a valid number, the parallel call can be activated.
If the parallel call is activated, incoming calls are routed
to your phone and all other destination phones in the
parallel call list. The connection is established with the
first phone that accepts the call.
If the call is not answered by any phone, it is forwarded
to the configured forwarding destination (on no reply) or
to a "rejection announcement".
143
OpenScape Voice functions
Step by step
Activating/deactivating parallel call via code
You can activate/deactivate the parallel call without having to change to edit mode.
Prerequisite: You have already entered numbers in the
parallel call list.
^ Lift the handset.
j Enter the code to activate or deactivate the parallel call
(see code table ! page 148).
144
OpenScape Voice functions
Step by step
Parking a call
If you have answered a call for a colleague and cannot
forward it to him, you can park the call.
Call park
[ You are conducting the call. Let the other party know,
e.g. that you are trying to connect him.
j Enter the code for parking followed by a line number
(see code table ! page 148).
You receive a confirmation tone. The caller hears a waiting melody.
] Replace the handset
Tell your colleague that a call for him is parked and give
him the line number.
Unparking
To unpark the call, your colleague must proceed as follows:
^ Lift the handset.
j Enter the unparking code (see code table ! page 148).
He is prompted to enter a line number.
j Enter the specified line number.
[ Your colleague is now connected with the waiting caller.
145
OpenScape Voice functions
Step by step
Silent Monitoring
If this function has been configured by service personnel and enabled for the destination phone, you can join
an active call of an internal station and listen in unnoticed (muted) or with the knowledge of the target station (active).
Active silent monitoring
Station A and B are on a call. You want to listen to the
call but so that Station B does not notice but so that you
can still talk to Station A.
Your phone
internal station A
internal or external station B
•
•
•
You can hear and talk to station A.
You can hear station B but cannot talk to him because he cannot hear you.
Station A and B can hear and speak to each other.
^ Lift the handset.
j Enter the code for active silent monitoring and the destination number (see code table ! page 148). You are
connected to the call and can listen. If necessary notify
station A.
] End the silent monitoring unnoticed by replacing the
handset.
146
OpenScape Voice functions
Step by step
Muted silent monitoring
Station A and B are on a call. You want to monitor a call
but so that neither station notices.
Your phone
internal station A
internal or external station B
•
•
•
You can hear station A but cannot talk to him because he cannot hear you
You can hear station B but cannot talk to him because he cannot hear you.
Station A and B can hear and speak to each other
^ Lift the handset.
j Enter the code for active silent monitoring and the destination number (see code table ! page 148). You are
connected to the call and can listen.
] End the silent monitoring unnoticed by replacing the
handset.
147
OpenScape Voice functions
Code table for OpenScape Voice functions
Ask your service personnel to enter the latest codes in the following table.
Print this page as an overview.
Function
148
Code
Description
Making anonymous calls off
! page 134
Making anonymous calls on
! page 134
Making anonymous calls temporarily on
! page 135
Making anonymous calls temporarily off
! page 135
List for selective call acceptance
! page 136
List for selective call rejection
! page 137
Rejecting anonymous calls
! page 138
Accepting anonymous calls
! page 138
Using abbreviated dialing
! page 139
Call tracing
! page 139
Making a line busy on
! page 140
Making a line busy off
! page 140
End of hunt group chain on
! page 141
End of hunt group chain off
! page 141
Edit mode for serial call
! page 142
Edit mode for parallel call
! page 143
Activating a parallel call
! page 144
Deactivating a parallel call
! page 144
Parking a call
! page 145
Unparking a call
! page 145
Active silent monitoring
! page 146
Muted silent monitoring
! page 147
Individual phone configuration
Step by step
Individual phone configuration
Display
Setting contrast
The display has multiple contrast levels that you can set
according to your light conditions.
z You can also configure this setting via the Web interface
z ! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Phone?
Select and confirm the option shown.
Display ?
f
Select and confirm the option shown.
Contrast: =
f
Select and confirm the option shown.
< or : Set and confirm the contrast
Save & exit
l
Select and confirm the option shown.
149
Individual phone configuration
Step by step
Date and time
This function allows you to select one of three different
display modes for the date and manually set the time if
necessary.
z You can also configure these settings via the Web interface ! page 178.
Setting the time
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Date and time?
Time = 14:44
Select and confirm the option shown.
f
Select and confirm the option shown. The time set is
displayed.
j Enter and confirm the time.
Save & exit
l
Select and confirm the option shown.
Setting the date
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Date and time?
Date = 20.02.2007
Select and confirm the option shown.
f
Select and confirm the option shown. The date set is
displayed.
j Enter and confirm the date.
Save & exit
150
l
Select and confirm the option shown.
Individual phone configuration
Step by step
Setting daylight saving time
Prerequisite: Auto DST is deactivated ! page 152.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Date and time?
Select and confirm the option shown.
Daylight saving = No
f
Select and confirm the option shown. The time set is
displayed.
Yes
l
Confirm.
Save & exit
l
Select and confirm the option shown.
Setting the difference between daylight saving and
standard time
Prerequisite: Auto DST is deactivated ! page 152.
Enter the difference to be used for daylight saving time.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Date and time?
Difference (mins) = 60
Select and confirm the option shown.
f
Select and confirm the option shown. The difference
set is displayed.
j Enter and confirm the difference between daylight and
standard time in minutes.
Save & exit
l
Select and confirm the option shown.
151
Individual phone configuration
Step by step
Automatic daylight saving time
The Auto DST setting is provided for information purposes and can only be changed by your service personnel.
z You can also access this information via the Web interface ! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Date and time?
Select and confirm the option shown.
Daylight saving time must be manually set if a No is entered for Auto DST ! page 151.
Time display format
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Locality?
Select and confirm the option shown.
Time format = 24 hours
m
Select and confirm the option shown. The format set is
displayed.
12 hours (AM/PM)
f
Select and confirm the time format (12- or 24-hour display).
Save & exit
l
Select and confirm the option shown.
152
Individual phone configuration
Step by step
Date display format
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Locality?
Select and confirm the option shown.
Date format = dd/mm/yyyy
f
Select and confirm the option shown. The format set is
displayed.
yyyy/mm/dd
f
Select and confirm the format you want.
Save & exit
l
Select and confirm the option shown.
153
Individual phone configuration
Step by step
Audio
Volumes
Use this selection to set the following volumes:
• Loudspeaker
• Ringer
• Handset
• Handsfree
• Rollover
z You can also configure this setting via the Web interface
! page 178.
Example: Handset:
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Audio
Select and confirm the option shown.
Volumes?
Select and confirm the option shown.
Handset
f
Select and confirm the option shown.
< or : Set and confirm the volume.
Save & exit
154
l
Select and confirm the option shown.
Individual phone configuration
Step by step
Settings
Room character
To ensure that the other party can hear you properly in
speakerphone mode, you can adjust the phone to the
room acoustics by choosing one of the following room
character conditions: "Normal", "Echoing", "Muffled" .
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Audio
Select and confirm the option shown.
Settings?
Select and confirm the option shown.
Room character = Normal
f
Select and confirm the room character in the context
menu (for example, "Normal").
Save & exit
l
Select and confirm the option shown.
Ringtone
If your service personnel has loaded suitable files to the
phone, you can select a realtone file in *.mp3 or *.wav
format for the ringer tone. If no individual audio files are
available the "pattern" ringtone is preset.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Audio
Select and confirm the option shown.
Settings?
Select and confirm the option shown.
155
Individual phone configuration
Step by step
Ringer file = Ring file
f
Select and confirm the option shown.
Ring file?
f
Confirm. Required ringtone file[1Select ] or "pattern." You
will immediately hear the associated ringer melody.
Confirm current ringtone file.
Save & exit
l
Select and confirm the option shown.
Pattern melody
z You can also configure this setting via the Web interface
! page 178.
Prerequisite: You have choosen the "pattern" ringtone,
see ! page 155.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Audio
Select and confirm the option shown.
Settings?
Select and confirm the option shown.
Ringer melody = 2
f
Select the required pattern melody[] between 1 and 8
(e. g. 4). You will immediately hear the corresponding
Ringer melody. Confirm the selected Ringer melody.
Save & exit
l
Select and confirm the option shown.
Pattern sequence
z You can also configure this setting via the Web interface
! page 178.
Prerequisite: You have choosen the "pattern" ringtone,
see ! page 155.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
1. The phone displays the current setting.
156
Individual phone configuration
Step by step
Audio
Select and confirm the option shown.
Settings?
Select and confirm the option shown.
Ringer tone sequence = 2
f
Select the required Ringer tone sequence between 1
and 3 (e. g. 2) You immediately hear the set Ringer melody with the select Ringer tone sequence. Confirm the
selected setting.
Save & exit
l
Select and confirm the option shown.
Country setting for speakerphone mode
Enter the country setting you prefer for speakerphone
mode here (see ! page 36).
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Audio
Select and confirm the option shown.
Settings?
Select and confirm the option shown.
Open listening = Standard mode
Select and confirm the setting you want in the context
menu ("Standard mode" or "US mode.
Save & exit
Select and confirm the option shown.
l
157
Individual phone configuration
Step by step
Tone and indication with an unsecured voice
connection
Use this option to activate an alerting tone that you hear
when a secure voice connection with the party you are
currently talking to ceases to be secure. The message
"Nonsecure connection" also appears.
Prerequisite: Secure connection setup is the preference set by your service personnel.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Secure call alert = No
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & exit
Select and confirm the option shown.
158
Individual phone configuration
Step by step
Key click
You can configure whether a key click should be audible
when a key is pressed. You can also decide whether
this should apply for all keys or only for the keys on the
keypad. In addition, you can adjust the click volume or
disable the sound.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
Settings
Select and confirm the option shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Phone
Select and confirm the option shown.
Key click
Select and confirm the option shown.
Adjusting the volume for the Key click
Volume
Select and confirm the option shown.
Medium
For instance, select and confirm a medium volume
level. You can also select one of the following three
options:
• Low
• Medium
• High
• Off (for no click)
Key selection
Keys
Select and confirm the option shown.
Keypad only
Select and confirm if the setting is only to apply for the
character input keys.
or
All keys
Select and confirm the option shown.
Save & exit
Confirm the option shown.
159
Individual phone configuration
Step by step
Setting the language and country
Selecting a language
Use this menu option to select the language for operator prompting.
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Locality?
Select and confirm the option shown.
Language = Deutsch
f
Select and confirm the option shown. The language set
is displayed.
English
f
Select and confirm to set the required language, in
our example, English.
Save & exit
l
Select and confirm the option shown.
160
Individual phone configuration
Step by step
You may choose from the following languages:
1. Bahasa Indonesia
2. Bahasa Malaysia
3. Brasileiro
4. Catal‡
5. Ceština
6. Dansk
7. Deutsch
8. Eesti keel
9. English
10. English(US)
11. EspaÒol
12. FranÁais
13. Hrvatski
14. Italiano
15. Latvieöu Valoda
16. Lietuviu Kalba
17. Magyar
18. Nederlands
19. Norsk
20. Polski
21. PortuguÍs
22. Rom‚na
23. Slovencina
24. Slovenski Jezik
25. Srpski Jezik
26. Suomi
27. Svenska
28. T¸rkÁe
29.
30.
31.
32. Русски
33.
34.
35.
161
Individual phone configuration
Step by step
Country-specific settings
Adapt your phone settings to suit the relevant countryspecific conditions (for example, transmission parameters).
z You can also configure this setting via the Web interface
! page 178.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Locality?
Select and confirm the option shown.
Country = Germany
f
Select and confirm the option shown. The country set
is displayed.
United States
f
Select and confirm to set the country[1], here US,
for instance.
Save & exit
l
Select and confirm the option shown.
You may choose from the following countries
1. Argentinien
2. Australia
3. Austria
4. Belgium
5. Brazil
6. Canada
7. China
8. Chile
9. Croatia
10. Czech Republic
11. Denmark
12. Finland
13. France
14. Germany
15. Hungary
16. India
17. Ireland
18. Italy
19. Japan
AR
AT
AU
BE
BR
CA
CN
CL
HR
CZ
DK
FI
FR
DE
HU
IN
IE
IT
JP
20. Luxembourg
LU
21. Mexico
MX
22. Netherlands
NL
23. New Zealand
NZ
24. Norway
NO
25. Poland
PL
26. Portugal
PT
27. Russian FederationRU
28. Singapore
SG
29. Slovakia
SK
30. South Africa
ZA
31. Spain
ES
32. Sweden
SE
33. Switzerland
CH
34. Thailand
TH
35. Turkey
TR
36. United Kingdom GB
37. United States
US
38. Vietnam
VN
1. The phone displays the current setting.
162
Individual phone configuration
Step by step
Network information
This overview in the user area of the Service menu provides you with information about the IP address of the
phone and the HTML address of the Web interface. It
also provides real-time data about the network activity
of the phone.
N Press the key shown.
User
Select and confirm the option shown.
if nec.j Enter and confirm the user password.
Network information
Select and confirm the option shown. You can browse
the following overview:
IP Address: Displays the IP address or name which was
assigned to the phone in the network.
WBM URL: HTTP address of the Web interface. This
address is specified in the address line of the Internet
browser and is used to call the Web interface of the
phone in the browser.
DNS domain: The DNS domain that can be assigned to
the telephone in addition to the IP address (e.g. http://
my-openStage.phone/).
LAN/PC-RX: The network or PC interface data packets
received are illustrated dynamically as columns.
LAN/PC-TX: The network or PC interface data packets
sent are illustrated dynamically as columns.
LAN/PC autonegotiated: [Yes|No]: Displays whether
the network or PC interface data transfer rate is set to
automatic (Yes) or manual (?No).
LAN/PC information: [10|100|1000] Mbit/s: Data
transfer rate of the network or PC interface. If an interface is not in use, Link down is displayed.
163
Individual phone configuration
Step by step
Resetting user data
The following user-specific settings changed via the
phone menu or the Web interface can be reset to factory settings.
• Display contrast
• Language setting
• Audio settings
– Volumes
– Settings
• Call lists
– All entries are deleted
• Programmable keys
– All personalized programming is deleted (see also
! page 74).
Attention: All data is reset without a warning tone.
Initiating the reset
v Press the key shown until the "Menu" tab is active.
User
Confirm.
if nec. j Enter and confirm the user password.
Reset
Select and confirm the option shown.
Reset all user data?
Select and confirm the option shown. The user data is
reset to factory settings.
or
Cancel?
164
To cancel the process.
Call recording
Step by step
Call recording
A central voice recorder is installed in the network for
recording calls to which your telephone connects in
order to record the current voice traffic. The recorder
records the entire voice flow of two or more
participants.
Call recording modes
The service personnel can configure the following
operating modes for call recording:
• Manual
• AutoStart
• All Calls
• Disabled
The following settings are possible to audibly signal the
recording:
• Repeated
• Single Shot
• Off
Check with your service personnel as to which settings
were made for your phone.
Mode: ALL CALLS:
The telephone starts and stops the recorder
automatically in order to ensure that all calls are being
recorded.
Mode: MANUAL
You decide when the recorder is started and stopped or
paused. If the recorder is switched on, all further calls
will be recorded. If you pause the recorder then nothing
will be recorded. If there are no calls, then the recorder
likewise pauses.
Mode: AUTOSTART
The telephone starts the recorder automatically. You
can stop or pause the recorder yourself however and
restart it. If a call has already been recorded, new
incoming and outgoing calls will also be recorded. If you
pause the recorder during a call, special calls such as
consultation calls, call pickups and second calls will not
165
Call recording
Step by step
be recorded as long as the recorder is paused. If the
telephone reverts to idle status, the AutoStart process
is set up again for the next call.
Explanations of recording
Recordable calls
A recordable call is any call that has a call connection
status on the telephone. This can be any incoming or
outgoing call. It is immaterial here whether a call is set
up directly via the telephone or via an application.
• Outgoing
• Incoming
• Consultation
• Pickup
• Reconnect
• Second call
• Connected call
• Conference1
• Automatic call acceptance
• Secured or unsecured line
Non-recordable calls
•
166
•
Outgoing calls that have not yet reached full
connection status, such as a ringing call.
Calls on hold
1.
Server-based conference only
Call recording
Step by step
Enhanced functions:
1. A conference1 can be set up or cleared down during
recording.
2. A consultation can be performed during recording.
3. Call transfer is also available during recording.
4. A second call can be accepted during recording.
The following features are not supported:
1. Playing back recordings over the telephone.
2. Deleting recordings over the telephone.
3. Functions for editing recordings over the telephone.
Recording tips
You will receive the following advisories while a call is
being recorded:
• The recording symbol | on the display
(permanent)
• Beep (repeated at intervals for you and your call
partner)
• Beep (single at the start of recording for you and
your call partner)
The audible advisory can also be switched off. Please
check with the relevant service personnel.
Recording calls
Using the call recording feature
The recording function can be used in a similar way to a
recorder, for example for recording music. The recorder
can be:
• switched on (standby .)
• switched off or stopped (~)
• started (/)
• paused (@)
The symbols used here by way of example can be found
on practically any hardware and software recorder.
1.
Server-based conference only
167
Call recording
Step by step
Automatic call recording
This is the simplest mode. If you have accepted a call or
called a subscriber and the subscriber answers, the call
is recorded automatically. Refer to ! page 166 to check
which calls this can be.
As soon as the recording starts, you will see the
recording symbol | and hear a beep (see also
! page 167).
You cannot pause the recording manually in this mode.
168
Call recording
Step by step
Manual call recording
Activating or deactivating call recording when the
telephone is in idle mode.
Prerequisite: Manual mode is selected. The recording
button is configured and indicates the status.
Recording on
Select the option shown in the telephone's context
menu to enable the option.
Recording off
or disable the option.
or
S Press the recording button to enable the option - the
LED key lights up.
R or press the key shown to disable the option - the LED
extinguishes.
The recording button also indicates the status change if
you activated or deactivated call recording via the
context menu.
Call recording with AutoStart
Standby mode is activated in principle in idle mode. The
recording button LED lights up. You cannot switch off
the recorder. As soon as a call is set up, call recording
starts automatically.
^ Lift the handset.
or
n Press the key shown.
[ The station answers. You hear a beep, the recording
symbol | is shown on the display and the recording
button LED remains lighting. The call is now being
recorded (see also ! page 167)
You can pause the recording at any time and continue it
again.
] or n If you end the call, the AutoStart process is set up again
for the next call.
169
Call recording
Step by step
Controlling call recording
Starting call recording manually during a call
Prerequisite: Manual mode or AutoStart is selected.
You are conducting a call. Recording has not started.
The recording button LED is not lighting.
[ You are conducting a call (see also ! page 166).
S Press the recording button to start the recording - the
LED key lights up.
You hear a beep and the recording symbol | is shown
on the display. The call is now being recorded (see also
! page 167)
Pausing call recording manually during a call
Prerequisite: Manual mode or AutoStart is selected.
You are conducting a call. Recording has started. The
recording button LED lights up.
[ You are conducting a call (see also ! page 166).
R Press the recording button to pause the recording - the
LED extinguishes and the recording symbol | on the
display disappears.
You can start the recording again at any time, for
example to continue recording the current call.
Ending call recording automatically
Prerequisite: You are conducting a call. Recording has
started. The recording button LED lights up.
] or n The recording is ended automatically as soon as the call
is terminated or if the call status changes so that the call
is no longer being recorded - for example if a line is
placed on manual hold and another line is seized
(Multiline).
The LED extinguishes and the recording symbol | on
the display disappears.
170
Call recording
Step by step
Consultation during call recording
Prerequisite: You are conducting a call. Recording has
started. The recording button LED is lighting.
You initiate a consultation – your main call is placed on
hold as a result while the consultation is being
performed.
j The recording is paused while you initiate the
consultation. The recording symbol | on the display
disappears.
[ If the consultation partner answers, the consultation
call is recorded. You hear a beep and the recording
symbol | is shown on the display again.
You can now terminate the consultation call or for
example switch back to the first call party (alternate)
while the consultation call is placed on hold.
Second call during call recording
Prerequisite: You are conducting a call. Recording has
started. The recording button LED is lighting.
[ You are conducting a call. You hear a beep and the
recording symbol | is shown on the display. The call
is now being recorded.
A second call party camps on ! page 83.
In the pop-up menu:
Accept
Select and confirm the option shown.
You are connected with the second party. You hear a
beep and the recording symbol | is shown in the line
for the second call – this call is now being recorded. The
first party is placed on hold.
171
Call recording
Step by step
Call recording while alternating
Prerequisite: You have an active or held consultation or
second call. Recording has started. The recording
button LED is lighting.
[ You are connected with the second party. You hear a
beep and the recording symbol | is shown in the line
for the second call.
Alternate
Select and confirm the option shown in the context
menu for this connection.
[ You are switched to the main call. You hear a beep and
the recording symbol | is shown in the line for the
main call – this call is now being recorded.
You can pause and restart the recording at any time in
manual and auto start modes.
Your call is paused and reconnected during
the recording.
Prerequisite: You are conducting a call that is being
recorded.
Z Your call partner has placed the call on hold. You hear
the music on hold. The recording is paused and the
recording symbol | has disappeared from the display.
[ Your call partner resumes the call. You hear a beep and
the recording symbol | is shown on the display.
172
Call recording
Step by step
Setting up a conference during recording
Prerequisite: You are conducting a consultation call
! page 50 or you have accepted a second call
! page 83 and the "System conference" feature was
configured by the service personnel. Recording has
started. The main call is placed on hold. The recording
button LED is lighting.
Conference
Select and confirm the option shown in the
connection's context menu. You are connected to both
parties at once. The conference is displayed with the
current participants.
You hear a beep and the recording symbol | is shown
in the line for the conference call.
Adding conference participants
Prerequisite: You have set up a conference. The
"System conference" feature was configured by the
service personnel. The conference call is now being
recorded.
[ You have performed a consultation or accepted a
second call (! page 50 or ! page 83). The conference
call is placed on hold.
You hear a beep and the recording symbol | is shown
in the line for the consultation or second call. The call is
now being recorded.
Conference
Select the option shown in the context menu for the
consultation or second call in order to include the new
participant in the conference. The conference is
displayed with all current participants.
You hear a beep and the recording symbol | is shown
again in the line for the conference call.
173
Call recording
Step by step
Your call is included in a conference during
the recording.
Prerequisite: You are conducting a call that is being
recorded. You are to be included in a conference by your
call partner. You are placed on hold while the
conference is being set up.
Z You hear the music on hold while your call partner is
setting up the conference. The recording is paused and
the recording symbol | has disappeared from the
display.
[ Your call partner answers again and you are connected
to the conference. You hear a beep and the recording
symbol | is shown in the "Conference" line. The
conference call is now being recorded.
Putting a line on hold manually during the
recording
There are two options for placing a line manually on
hold:
• You place the active line on hold during the call
recording and then resume the call on this line.
• You seize a different line during call recording. The
first line is placed on manual hold.
Prerequisite: The telephone has more than one line
configured. The active line is being recorded. The
recording button LED is lighting.
Holding and retrieving the call on the line
[ You are conducting a call, for example on line A. You
hear a beep and the recording symbol | is shown on
the display. The call is now being recorded.
R Press line key A. The line key LED starts flickering. The
call is placed on hold. The recording is paused while the
call is on hold. The recording symbol | on the display
disappears.
174
Call recording
Step by step
Retrieving a held call:
T Press line key A. The line key LED lights up. The call is
retrieved. You hear a beep and the recording symbol
| is shown on the display again. Call recording is
continued.
Holding a call on the line and conducting a call on a
different line
S Press line key B – the LED lights up. You hear a beep
and the recording symbol | is shown on the display
for line B – this call on line B is being recorded. Line A
is placed on hold, call recording of line A has been
terminated.
T Press line key A to resume the call. You hear a beep and
the recording symbol | is shown on the display for
line A – a new recording of line A commences.
175
Call recording
Step by step
Diagnostic information
This information overview in the user area of the service
menu provides you with information on the current configuration of the telephone:
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the user password.
Diagnostic information
Select and confirm the option shown.
You see a numbered list of telephone parameters with
the current settings.
You can see a more structured view of the list via the
WEB-Oberfläche ! page 178:
Example:
Diagnostic.Information
2011-05-23 12:24:00
176
00
terminal.number:
3334
01
sip.server:
192.168.1.240
02
sip.port:
5060
03
sip.registrar:
192.168.1.240
04
sip.registrar.port:
5060
05
sip.gateway:
192.168.1.240
06
sip.transport:
UDP
07
sip.gateway.port:
5060
08
server.features:
No
09
dns.results:
5060
10
multiline:
No
11
registered.lines:
5060
12
backup.active:
Yes
13
backup.proxy:
14
software.version:
V3 R0.24.0 SIP
110514
15
display.message:
None
16
last.restart:
2011-0519T13:42:02
Call recording
Step by step
Diagnostic.Information
17
memory.free:
18
ip.adress:
23131K free
192.168.1.203
19
subnet.mask:
255.255.255.0
20
default.route:
192.168.1.2
21
primary.dns:
192.168.1.105
22
secondary.dns:
192.168.1.2
23
route.1.ip:
24
route.1.gateway:
None
25
route.1.mask:
None
26
route.2.ip:
None
27
route.2.gateway:
None
28
route.2.mask:
None
29
mac-address:
0001e32c680c
30
discovery.mode:
Manual
31
dhcp.reuse:
No
32
lan.port.type:
0
33
pc.port.status:
None
34
pc.port.type:
0
35
pc.port.autoMDIX:
No
36
vlan.id:
37
qos.layer.2:
38
qos.layer.2.voice:
39
qos.layer.2.signalling:
None
40
qos.layer.2.default:
0
41
qos.layer.3:
Yes
42
qos.layer.3.voice:
13
43
qos.layer.3.signalling:
7
44
lldp.med.operation:
5
177
Web interface
Web interface
General
You can configure a number of settings for your phone via the Web interface. Communication is via a secure HTTPS connection. Access to the
Web interface must be activated by service personnel.
Calling up the Web interface
For more information on the IP address, the Web interface address,
and how to connect the telephone to the network, refer to the section entitled "Network information" ! page 163.
To call up the interface, open a Web browser and enter the following:
https://[IP address of the phone]
[IP address of the phone] is the IP address of your phone.
https://[Name of the phone]
[Name of the phone] which was assigned by service personnel.
You might receive a certificate notification from the browser. Follow
the instructions to download the certificate.
You will be prompted to configure a user password the first time you
call up the Web interface ! page 123. You must log on with this
password in future every time you want to open the User Pages.
Administrator Pages
This area lets you configure settings for administering your phone and the
network environment. Access to the Administrator Pages is protected by
the admin password. For more information, contact your service personnel
or refer to the administration manual.
178
Web interface
User pages
The Web interface homepage opens once you have entered and confirmed
the phone’s IP address:
User menu
User selection
Phone information
User login
Highlighted entry (current page)
Menu heading
Menu entry
1. Click a menu heading to display the individual menu entries. Click the
menu heading again to close the menu.
2. Click a menu entry to open the corresponding form.
3. Make the desired changes.
4. Click the corresponding button to save or discard your changes.
Button functions
• "Login": Log on to the phone after you have entered the user password
• "Submit": Apply changes
• "Reset": Reset original values
• "Refresh": Update the values.
• "Logout": Log off the phone
179
Web interface
User menu
All settings that you can make via the Web interface’s user menu can also
be made via the phone’s user menu
User Pages
User login V ! page 123
Date and Time
– Local time V ! page 150
– Local date (day, month, year) V ! page 150
– Allow daylight saving V ! page 151
– Difference (minutes) V ! page 151
– Auto time change V ! page 152
Audio
– Ringer melody (V ! page 156)
– Ringer tone sequence (V ! page 156)
– Ring file (V ! page 155)
– Room Character (V ! page 155)
– Open listening (V ! page 157
Configuration
– Outgoing calls
– Autodial delay (seconds) V ! page 94
– Callback option V ! page 64
– Allow busy when dialing V ! page 96
– Allow transfer on ring V ! page 90
– Allow immediate dialing ! page 47
– Incoming calls
– Deflecting
– Allow deflection (V ! page 75
– Default deflect destination V ! page 75
– Deflect to DSS V ! page 76
– Forwarding
– Settings
– Forwarding Favorites Destination 1 to Destination 5
V ! page 56
– Forward all calls allowed V ! page 58
– to V ! page 58
– Direct destination V ! page 55
– Forward on busy allowed V ! page 58
– to V ! page 58
– Direct destination V ! page 55
– Forward on no reply allowed V ! page 58
– to V ! page 58
– Direct destination V ! page 55
– No reply delay (seconds)[1] V ! page 60
[1]. Only if "Server features" was deactivated by your administrator
180
Web interface
– Alerts
– Visual alerts V ! page 78
– Audible alerts V ! page 78
– Forwarding party ! page 61
– Handling
– Allow call waiting V ! page 86
– Allow DND V ! page 122
– Allow busy when dialing V ! page 96
– CTI calls
– Allow auto-answer V ! page 91
– Allow beep on auto-answer V ! page 91
– Allow auto-reconnect V ! page 92
– Allow beep on auto-reconnect V ! page 92
– Connected calls
– Allow call transfer V ! page 89
– Allow call joining V ! page 53
– Allow exit conferenceV ! page 99
– Allow hold reminder V ! page 80
– Hold reminder delay (minutes) V ! page 81
– Allow music on hold V ! page 82
– Allow conferences V ! page 98
– Allow secure call alert V ! page 158
– Toggle associate ! page 87
– Keyset
– Lines
– Ring delay (seconds) V ! page 117
– Address[1]
– Primary line[1]
– Ring on/off[1]
– Hot-/Warmline[1]
– Hot warm destination V ! page 108
– Overview
– BLF
– Busy Lamp Field: not for OpenScape Voice
Phone
– Display settings
– Contrast V ! page 149
– Program keys
– Normal
– Edit V ! page 67 .
– Shifted
– Edit V ! page 67.
– Key Module (if available such as Program keys)
– Key click
– Volume
– Off
[1]. Information - read only
181
Web interface
– Low
– Medium
– High
– Keys
– Keypad only
– All keys
Locality
– Country V ! page 162
– Language V ! page 160
– Date format V ! page 153
– Time format V ! page 152
Security
– Password
– Current Password
– New password V ! page 123
– Confirm password
Diagnostic information V ! page 176
182
Fixing problems
Fixing problems
Caring for your telephone
•
•
•
•
Never allow the telephone to come into contact with coloring, oily or
aggressive agents.
Always use a damp or antistatic cloth to clean the telephone. Never
use a dry cloth.
If the telephone is very dirty, clean it with a diluted neutral cleaner containing surfactants, such as a dish detergent. Afterwards remove all
traces of the cleaner with a damp cloth (using water only).
Never use cleaning fluids containing alcohol or plastic-damaging detergents to clean the telephone. The use of scouring agents is also forbidden.
Troubleshooting
Pressed key does not respond:
• Check if the key is stuck.
• If the telephone is locked repdial keys cannot be used. This also applies
when an emergency number is saved on it.
Check whether your telephone is locked ("Phone locked. To unlock enter
the PIN" appears on the screen). If the phone is locked, unlock it.
The phone does not ring on call:
Check whether the ringtone is deactivated (see icon in the status bar on
the display ! page 121). If it is deactivated, activate the ringtone
You cannot dial a number:
Check whether your telephone is locked ("Phone locked. To unlock enter
the PIN" appears on the screen ). If the phone is locked, unlock it.
To correct any other problems:
First contact the relevant service personnel. If the service personnel are
unable to correct the problem, contact Customer Service.
Contact partner in the case of problems
Contact your service personnel if a fault persists for more than five minutes, for example.
183
Fixing problems
Labeling keys
The following options are available for labeling keys of the OpenStage 15
and/or OpenStage Key Module 15 with the functions assigned to them or
the saved numbers on them:
Labeling
• By hand:
Labeling strips are supplied with your OpenStage 15 and
OpenStage Key Module 15. Note the function or name in the white
field on the strip and insert the strip on your OpenStage 15 or
OpenStage Key Module 15.
• With a computer via the Internet:
You can find the "online labeling tool" together with the user interface at
http://wiki.siemens-enterprise.com/index.php/Key_Labelling_Tool.
• Select the appropriate key labeling tool in your language. You can use
the tool online via the browser or you can download it for local use.
184
Local user menu
Local user menu
Opening the user menu on the phone
To open the user menu, press the N key.
On the Settings tab, select the User menu option. You are prompted to
enter the User password ! page 123. Confirm this with OK. The options
of the user menu are available.
User menu display
The majority of settings that can be made via the user menu on the phone,
can also be made via the web interface ! page 178.
Changes are usually confirmed using the Save & exit option or discarded
using the Exit (no save) option.
The options grayed out are not available on the OpenStage 15 or have no
function.
! User
Date and time?
– Time = hh:mm
– Date = DD.MM.YYYY
– Daylight saving = Yes
– No?
– Return?
– Difference (mins) = mm
– Auto DST = Yes/No
– Save & exit
– Exit (no save)
! page 150
! page 150
! page 151
! page 151
! page 152
! Audio?
– Volumes?
– Loudspeaker =
– Ringer =
– Handset =
– Headset =
– Handsfree =
– Rollover =
– Save & exit
– Exit (no save)
– Settings?
– Ringtone = Ring file
– Pattern?
– Ringer1.wav?
– Ringer2.wav?
! page 154
! page 154
! page 154
! page 154
! page 154
! page 155
185
Local user menu
– Ringer3.wav?
– Ringer4.wav?
– Ringer5.wav?
– Ringer6.wav?
– Return?
– Ringer melody = 2
– 1?
– 2?
– 3?
– 4?
– 5?
– 6?
– 7?
– 8?
– Return?
– Ringer tone sequence= 1
– 1?
– 2?
– 3?
– Return?
– Room character = Normal
– Normal?
– Echoing?
– Muffled?
– Return?
– Open listening = Standard mode
– Standard mode?
– US mode?
– Return?
– Save & exit
– Exit (no save)
– Return?
! page 156
! page 156
! page 155
! page 157
! User Configuration?
– Outgoing calls?
– Autodial delay = 6
– 1?
– 2?
– 3?
– 4?
– 5?
– 6?
– 7?
– 8?
– 9?
– Return?
– Callback = No
– Yes?
186
! page 95
! page 64
Local user menu
– Return?
– Busy when dialing = Yes
– No?
– Return?
– Transfer on ring = Yes
– No?
– Return?
– Immediate dialing = Yes
– No?
– Return?
– Save & exit
– Exit (no save)
– Incoming calls?
– Deflecting?
– Allow deflection = Yes
– No?
– Return?
– Default destination =
– Deflect to DSS = Yes/No[1]
– Save & exit
– Exit (no save)
– Forwarding?
– Settings?
– " All calls: 12345
– Turn on?
– Enter destination
– List of saved numbers, if applicable
– Edit favorites?
– Destination 1
– Destination 2
– Destination 3
– Destination 4
– Destination 5
– Save & exit
– Exit (no save)
– Copy
– Paste (if copying is active)
– Return
– " Busy: 12345
– Turn on?
– Enter destination
– List of saved numbers, if applicable
– Edit favorites?
– Destination 1
– Destination 2
– Destination 3
! page 96
! page 90
! page 47
! page 75
! page 75
! page 76
! page 58
! page 56
! page 57
! page 57
! page 57
! page 58
! page 56
! page 57
[1]. Information - read only
187
Local user menu
– Destination 4
– Destination 5
– Save & exit
– Exit (no save)
– Copy
– Paste (if copying is active)
– Return
– " No reply: 12345
– Turn on?
– Enter destination
– List of saved numbers, if applicable
– Edit favorites?
– Destination 1
– Destination 2
– Destination 3
– Destination 4
– Destination 5
– Save & exit
– Exit (no save)
– Copy
– Paste (if copying is active)
– Set delay = 16[1]
– Alerts
– Visual alerts = No
– On?
– Return?
– Audible alerts = No
– On?
– Return?
– Forwarding party = Display last
– Display first?
– Display last?
– Return?
– Save & exit
– Exit (no save)
– Handling?
– Allow call waiting = Yes
– No?
– Return?
– Allow DND = Yes
– No?
– Return?
– Busy when dialing = Yes
– No?
– Return?
– Save & exit
– Exit (no save)
[1]. Only if "Server features" was deactivated by your administrator
188
! page 57
! page 57
! page 58
! page 56
! page 57
! page 57
! page 57
! page 60
! page 78
! page 78
! page 61
! page 86
! page 122
! page 96
Local user menu
– CTI calls?
– AutoAnswer = Yes
– No?
– Return?
– AutoAnswer beep = Yes
– No?
– Return?
– AutoReconnect beep = Yes
– No?
– Return?
– Save & exit
– Exit (no save)
– Return?
– Connected calls?
– Allow call transfer = Yes
– No?
– Return?
– Allow call joining = Yes
– No?
– Return?
– Allow exit conf = Yes
– No?
– Return?
– Allow hold rem. = Yes
– No?
– Return?
– Hold rem. delay = 8
– 3?
– 4?
– 5?
– 6?
– 7?
– 8?
– 9?
– 10?
– 11?
– 12?
– 13?
– 14?
– 15?
– Return?
– Music on hold = Yes
– No?
– Return?
– Allow conferences =Yes
– No?
– Return?
! page 91
! page 91
! page 92
! page 89
! page 53
! page 99
! page 80
! page 81
! page 82
! page 98
189
Local user menu
–
–
–
–
– Secure call alert = Yes
– No?
– Return?
– Toggle associate =Yes
– No?
– Return?
– Save & exit
– Exit (no save)
! Keyset?
– Lines?
– Line (one of eight possible)
– Ring delay = 0
– Allow in overview = Yes
– No?
– Return?
– Hot warm action[1] = No Action
– Hot warm dest = nnnn
– Address[1] = nnnn
– Ring on/off[1] = On
– Selection order[1] = 1
– Save & exit
– Exit (no save)
– Return?
– Overview?
– Line (up to eight lines)
– Move down?
– Move to bottom?
– Use FPK order?
– Add all lines?
– Return?
– Save
– Do not save
– Return?
– Return?
BLF?
Busy Lamp Field: not for OpenScape Voice
Return?
! page 158
! page 87
! page 117
! page 108
! Phone?
– Display settings?
– Contrast =
– Save & exit
– Exit (no save)
– Program keys
Press the key to be programmed
– Normal = Unallocated
– Unallocated?
[1]. Information - read only
190
! page 149
! page 67
Local user menu
– Further functions, see
– Label = predefined or customized
– Settings = function-dependent
– Shifted = Unallocated
– Unallocated?
– Further functions, see
– Label = predefined or customized
– Settings = function-dependent
– Save & exit
– Exit (no save)
– Key Module (if available such as Program keys)
– Key click
– Options
Save & exit
– Exit (no save)
– Volume
– Off
– Low
– Medium
– High
– Keys
– Keypad only
– All keys
– Return?
Locality?
– Country = DE
– DE?
– Further countries, see
– Return?
– Language = Deutsch
– Deutsch?
– Further languages, see
– Return?
– Date format = dd/mm/yyyy
dd/mm/yyyy?
yyyy/mm/dd?
– mm/dd/yyyy?
– Return?
– Time format = 24 hour
– 24 hour?
– 12 Hour (AM/PM)?
– Return?
– Save & exit
– Exit (no save)
Security?
– Change user password?
– Current password =
! page 193
! page 67
! page 194
! page 159
! page 159
! page 162
! page 162
! page 160
! page 161
! page 153
! page 152
! page 123
191
Local user menu
– New user password =
– Confirm New user password =
– Save & exit
– Exit (no save)
– Phone lock?
– Save & exit
– Exit (no save)
– Phone lock =
No
– Yes
Network information?
– Phone address =
– Web address =
– IP address =
– LAN RX =
– LAN TX =
– PC RX =
– PC TX =
– LAN autonegotiated = Yes
– LAN information = 10 Mbps full duplex
– PC autonegotiated = Yes
– PC information = Link down
– Exit (no save)
Diagnostic information
Reset?
– Reset all user data?
– Function key data = No?
– Yes?
– Return?
– Reset selected user data?
– Cancel?
Back?
192
! page 126
! page 163
! page 176
! page 164
! page 74
! page 74
Local user menu
Key functions
Normal
You can program the following functions on the Normal of the function
keys:
• Selected dialing
• Repeat dialing
• Forward all calls
• Forward no reply
• Forward busy
• Mute
• Ringer off
• Hold
• Alternate
• Blind transfer call
• Transfer call
• Deflecting
• Shift
• Conference
• Headset
• Do not disturb
• Group pickup
• Repertory dial
• Feature toggle
• Mobility
• Directed pickup
• Release
• Callback
• Cancel callbacks
• Consultation
• Call Waiting toggle
• Immediate ring
• PreView
• Call recording
• Start application
• Built in fwd
193
Local user menu
Shifted
You can program the following functions on the Shifted of the function
keys:
• Selected dialing
• Repeat dialing
• Alternate
• Blind transfer call
• Transfer call
• Deflecting
• Conference
• Repertory dial
• Release
• Callback
• Cancel callbacks
• Consultation
• Start application
194
Index
Index
Numerics
2nd alert ....................................................... 43
A
Accepting calls
multi-line ................................................ 103
Administration ............................................ 30
Allowing call joining ................................... 53
Alternate ...................................................... 51
Application ................................................... 91
Audio
room character ..................................... 155
Autodial delay ............................................. 94
AutoReconnect ........................................... 92
B
Busy override ............................................ 109
Busy tone while dialling ............................ 43
C
Call
accepting ................................................. 33
deflect ...................................................... 75
ending ...................................................... 38
forwarding ............................................... 54
holding ...................................................... 79
incoming .................................................. 32
rejecting ................................................... 76
transfer ..................................................... 88
Call control .................................................. 43
Call forwarding
Activate/deactivate ................................ 58
Copy and insert destination phone numbers ........................................................... 57
Destination phone number ................... 55
Favourites ................................................ 57
last destination ....................................... 55
Save destination phone number .......... 56
Variable .................................................... 55
Call forwarding chain ................................. 61
Call forwarding favourites ......................... 57
Call forwarding information .................... 105
Call list .......................................................... 65
Call lists ...................................................... 102
Call log ................................................... 28, 65
Call recording
alternating .............................................. 172
automatic ............................................... 168
AutoStart ................................................ 169
call types ................................................ 166
conference ............................................ 173
consultation ........................................... 171
controlling .............................................. 170
line key ................................................... 174
manual .................................................... 169
modes .................................................... 165
second call ............................................. 171
symbols .................................................. 167
tips .......................................................... 167
using ....................................................... 167
Call settings
CTI calls .................................................. 155
MultiLine ................................................ 117
Call waiting ............................................ 43, 83
Call waiting (second call) ........................... 83
Callback ........................................................ 62
Calls .............................................................. 91
CE marking .................................................... 2
Conference .................................................. 97
starting conference ................................ 50
Connecting parties ..................................... 53
Connection options .................................... 15
Consultation .......................................... 43, 50
Consultation call from second call .......... 83
Context ........................................................ 47
Context menus ........................................... 26
Contrast ..................................................... 149
Copy and insert destination phone numbers ............................................................... 57
CTI ................................................................ 91
D
Date and time ........................................... 150
Date format ............................................... 153
Daylight saving ......................................... 151
Destination phone number ....................... 55
Dial plan ....................................... 94, 126, 127
Display contrast ........................................ 149
Do not disturb ........................................... 121
DSS call
call deflection ........................................ 112
195
Index
DSS key
consultation ........................................... 110
indirect pickup ...................................... 111
reject call ............................................... 111
During calls
multi-line ................................................ 106
E
Emergency call ................................. 126, 127
Emergency number ......................... 126, 127
F
Forced logoff ............................................ 132
Forwarding .................................................. 54
Forwarding primary line .......................... 105
Function key
programmable ........................................ 19
G
General information ................................... 11
Group call .................................................... 39
H
Hold reminder tone ................................... 80
Holding ......................................................... 79
Hot line ........................................................ 48
for lines .................................................. 108
I
Idle mode .................................................... 24
Immediate dialing ................................ 47, 94
Important information ............................. 2, 3
Incoming calls
multi-line ................................................ 103
K
Key
Immediate ring ....................................... 73
Key click ..................................................... 159
Keypad ......................................................... 22
196
L
Language settings ................................... 160
LED display
direct station selection keys ................. 19
function keys ........................................... 19
Line preview ............................................. 118
Line utilization ............................................. 20
Lines
hot/warm line ........................................ 108
Locality ............................................... 157, 162
Location of the telephone .......................... 3
Logging on and off
as a mobility user ......................... 129, 131
M
Mailbox key ........................................... 14, 18
Making calls
multi-line ................................................ 104
Menu key .............................................. 14, 18
Microphone ................................................. 38
Missed calls ................................................ 65
Mobility ...................................................... 128
forced logoff .......................................... 132
logon, logoff .................................. 129, 131
Multi-line
accepting calls ...................................... 103
LED display ..................................... 21, 112
Multiline
busy override ........................................ 109
Multi-line telephone ................................... 13
Music on hold ............................................. 82
N
Normal dialing ............................................. 47
Index
O
Open listening ............................................ 37
OpenScape Voice .................................... 133
accepting anonymous calls ................ 138
call tracing .............................................. 139
creating a list for selective calls ......... 136
Feature toggle key ............................... 133
functions ................................................ 133
hunt group ............................................. 140
making anonymous calls ..................... 134
parallel call ............................................. 143
parking .................................................... 145
reachability ............................................ 142
rejecting anonymous calls .................. 138
serial call ................................................ 142
silent monitoring ................................... 146
Operating instructions ................................. 2
P
Padlock icon ................................................ 32
Parallel call ................................................. 143
Parking ....................................................... 145
Party connection ........................................ 53
Phantom line ............................................... 20
Phone
locking .................................................... 126
Phone settings ......................................... 149
Picking up the held call ............................. 35
Primary line ................................................. 20
Privacy ........................................................ 120
Private line ................................................... 20
Program/Service menu ............................. 29
Programmable function key ..................... 19
Programmable keys ................................... 66
R
Reachability ............................................... 142
Redial ........................................................... 49
Redialing
multi-line ................................................ 105
Repdial keys ................................................ 93
Ringer melody .......................................... 156
Ringer off ................................................... 120
Ringtone sequence .................................. 156
S
Save destination phone number ............. 56
Second call
ignoring .................................................... 84
Second call with consultation call ........... 83
Secondary line ............................................ 20
Security .............................................. 120, 123
Serial call .................................................... 142
Service menu .............................................. 29
Setting the time ........................................ 150
Settings ................................................ 29, 149
Shared line ................................................... 20
Silent monitoring ...................................... 146
Single-line telephone ................................. 13
Speakerphone distance .............................. 3
Speakerphone mode ........................... 33, 36
T
Telephone maintenance ......................... 183
Time display format ................................. 152
Troubleshooting ........................................ 183
U
Unlocking the phone ............................... 127
User interface
OpenStage 15 ......................................... 14
User password ......................................... 123
User support ............................................... 12
Using Ethernet switches .......................... 16
Using network ports more efficiently ..... 16
V
Variable call forwarding ............................. 55
W
Warm line .................................................... 48
for lines .................................................. 108
Web interface ................................... 178, 185
197
Copyright © Siemens Enterprise
Communications GmbH & Co. KG
Hofmannstr. 51
80200 München
Deutschland
Siemens Enterprise
Communications GmbH & Co. KG
is a Trademark Licensee of Siemens AG
Reference No:
A31003-S2030-U103-1-7619
Communication for the open minded
Siemens Enterprise Communications
www.siemens-enterprise.com
The information provided in this document
contains merely general descriptions or characteristics of performance which in case of
actual use do not always apply as described
or which may change as a result of further
development of the products.
An obligation to provide the respective characteristics shall only exist if expressly agreed
in the terms of contract. Availability and
technical specifications are subject to
change without notice. OpenScape,
OpenStage and HiPath are registered trademarks of Siemens Enterprise
Communications GmbH & Co. KG.
All other company, brand, product and service names are trademarks or registered
trademarks of their respective holders.