Medtronic LIFEPAK CR-T Operating instructions

SETUP INSTRUCTIONS
LIFEPAK® CR–T
AED Trainer
After receiving the LIFEPAK CR–T AED Trainer, carefully remove the Trainer and the operating instructions from the
shipping container. Examine the Trainer and accessories for any sign of damage during shipping.
Shipping container contents include:
•
LIFEPAK CR–T AED Trainer
•
QUIK-PAK™ training electrodes
•
Remote control
•
2 AAA alkaline batteries (for remote control)
•
Remote control cable
•
4 D-cell alkaline batteries (for Trainer)
•
Yellow plastic shock key cover
•
Operating instructions
•
CHARGE-PAK™ Trainer
•
Lid labels (international trainers only)
•
Quick reference card
•
Soft case with identification card
If any components are missing or the Trainer appears to be damaged, contact your dealer or local Medtronic
representative right away. Save the container for reshipping the Trainer if necessary.
Always place the Trainer in a location separate from the defibrillator to avoid confusion in real emergencies.
AAA +
AAA +
–
–
Accessory Bag
Accessory
Bag
+ D-Cell – + D-Cell –
– D-Cell
+
– D-Cell
+
Soft Case
Medtronic, Inc.
11811 Willows Road NE
Redmond, WA 98052-2003 USA
Telephone: 425.867.4000
Toll Free (USA only): 800.442.1142
Fax: 425.867.4121
Internet: www.medtronic-ers.com
Medtronic Europe S.A.
Rte. Du Molliau 31
Case postale 84
1131 Tolochenaz
Switzerland
Telephone: 41.21.802.7000
Fax: 41.21.802.7900
Medtronic and LIFEPAK are registered trademarks of Medtronic, Inc. CHARGE-PAK and QUIK-PAK are trademarks of Medtronic, Inc.
Specifications are subject to change without notice.
© 2002-2007 Medtronic, Inc. All rights reserved.
LIFEPAK CR–T
®
AED Trainer
Operating Instructions
OPERATING INSTRUCTIONS
LIFEPAK® CR–T
AED Trainer
Text Conventions
Throughout these operating instructions, special text characters are used to indicate labels and voice
prompts:
•
Operating control labels: CAPITAL LETTERS such as LID RELEASE/ON-OFF.
•
Voice prompts: CAPITAL ITALICIZED LETTERS such as CALL FOR HELP NOW.
Version History
These operating instructions describe the LIFEPAK CR–T AED Trainer, MIN 3201804-005 or later.
Medtronic , Inc.
11811 Willows Road NE
Redmond, WA 98052-2003 USA
Telephone: 425.867.4000
Toll Free (USA only): 800.442.1142
Fax: 425.867.4121
Internet: www.medtronic-ers.com
Medtronic Europe S.A.
Rte. Du Molliau 31
Case postale 84
1131 Tolochenaz
Switzerland
Telephone: 41.21.802.7000
Fax: 41.21.802.7900
Medtronic and LIFEPAK are registered trademarks of Medtronic, Inc. CHARGE-PAK and QUIK-PAK are trademarks of Medtronic, Inc.
Specifications are subject to change without notice.
©2002-2007 Medtronic, Inc. All rights reserved.
MIN 3201838-003 / CAT. 26500-001156
ii
LIFEPAK CR–T Trainer Operating Instructions
TABLE OF CONTENTS
1
1 Getting Started
Introduction ............................................................................................................................................. 2
Unpacking and Inspecting the LIFEPAK CR–T AED Trainer .................................................................. 2
Controls, Indicators, and Labels ............................................................................................................. 3
Outside Controls, Indicators, and Labels ........................................................................................ 3
Remote Control and Remote Control Cable ................................................................................... 7
Installing and Replacing Batteries .......................................................................................................... 8
Installing and Replacing Trainer Batteries....................................................................................... 8
Installing and Replacing Remote Control Batteries......................................................................... 8
2 Using the LIFEPAK CR–T AED Trainer
Voice Prompts and Tones ..................................................................................................................... 10
Using the Remote Control .................................................................................................................... 10
Remote Control Functions ............................................................................................................ 10
Using the Remote Control Cable .................................................................................................. 12
Preparing for a Training Session ........................................................................................................... 12
Conducting a Training Session ............................................................................................................. 13
Following a Training Session ................................................................................................................ 14
3 Setup
Setup Configuration and Operating Settings ........................................................................................ 16
Changing Options for Operating Settings ............................................................................................. 18
Using the Remote Control and the LED Display ........................................................................... 18
Procedures for Changing Operating Settings................................................................................ 18
Shock Protocol .............................................................................................................................. 18
Selecting Shock Protocols.................................................................................................... 18
Configuring Shock Protocols ................................................................................................ 19
General Operating Settings........................................................................................................... 20
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
iii
CPR Time...................................................................................................................................... 21
Language Option........................................................................................................................... 21
Setup .................................................................................................................................... 22
Resetting Default Settings............................................................................................................. 22
4 Caring for the LIFEPAK CR–T AED Trainer
Replacing Batteries ............................................................................................................................... 24
Troubleshooting ..................................................................................................................................... 24
Cleaning ................................................................................................................................................ 26
Product Recycling Information .............................................................................................................. 26
Recycling Assistance .................................................................................................................... 26
Preparation.................................................................................................................................... 26
Recycling of Training Electrodes ................................................................................................... 26
Packaging...................................................................................................................................... 26
Warranty ............................................................................................................................................... 26
Accessories .......................................................................................................................................... 27
Specifications ........................................................................................................................................ 27
A LIFEPAK CR–T AED Trainer Voice Prompts and Tones ....................................................... 29
B LIFEPAK CR–T AED Trainer Quick Start Reference Card .................................................... 33
C Declaration of Conformity .................................................................................................... 37
Index............................................................................................................................................. 41
iv
LIFEPAK CR–T Trainer Operating Instructions
LIST OF FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
LIFEPAK CR–T AED Trainer Outside Controls, Indicators, and Labels (Top and Bottom) ........ 3
LIFEPAK CR–T AED Trainer Outside Controls, Indicators, and Labels (Back and Side) .......... 4
LIFEPAK CR–T AED Trainer Inside Features ........................................................................... 5
Inside Features after Opening the Electrode Packet ................................................................. 6
Remote Control and Remote Control Cable.............................................................................. 7
LIFEPAK CR–T AED Trainer and Remote Control Battery Placement...................................... 8
Connecting the Training Electrode Packet to the LIFEPAK CR–T AED Trainer....................... 13
Placing Training Electrodes on the Manikin............................................................................. 14
LED Display............................................................................................................................. 18
Custom #1 and #2 Options...................................................................................................... 19
General Operating Setting Options ......................................................................................... 20
CPR Time Options .................................................................................................................. 21
Language Options ................................................................................................................... 22
LIST OF TABLES
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Outside Controls, Indicators, and Labels (Top and Bottom) ..................................................... 3
Outside Controls, Indicators, and Labels (Back and Side) ....................................................... 4
Inside Features......................................................................................................................... 5
Inside Features after Opening the Electrode Packet ................................................................ 6
Remote Control Features (Setup Functions)............................................................................ 7
Remote Control Button Functions .......................................................................................... 10
Trainer Operating Setting Options .......................................................................................... 16
Shock Protocol Options .......................................................................................................... 19
General Operating Setting Options ........................................................................................ 20
Language Groups................................................................................................................... 21
Voice Prompts and Tones Troubleshooting............................................................................. 24
LED Display Troubleshooting ................................................................................................. 24
Setup Options Troubleshooting .............................................................................................. 25
Remote Control Troubleshooting ............................................................................................ 25
Training Electrodes Troubleshooting....................................................................................... 25
LIFEPAK CR–T AED Trainer Accessories .............................................................................. 27
LIFEPAK CR–T AED Trainer Specifications ........................................................................... 27
Remote Control Specifications ............................................................................................... 28
Voice Prompts and Tones....................................................................................................... 31
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
v
Getting Started
1 GETTING STARTED
This section introduces the LIFEPAK® CR–T Automated External Defibrillator (AED) Trainer and
provides an orientation to its features.
Introduction
Unpacking and Inspecting the LIFEPAK CR–T
AED Trainer
Controls, Indicators, and Labels
Installing and Replacing Batteries
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
page 2
2
3
8
1
Getting Started
INTRODUCTION
The LIFEPAK CR–T AED Trainer provides the necessary interface for practical skill demonstration
during a simulated cardiac arrest. The Trainer is designed to assist the instructor with realistic training
on the use of the defibrillator without the actual charge and discharge of electrical energy.
The Trainer simulates voice prompts, audible tones, and readiness display features of all LIFEPAK CR
defibrillator models. These features help guide trainees through simulated analysis, simulated shock
delivery, and prompted CPR time.
An infrared, wireless, remote control allows the instructor to operate the Trainer during training sessions.
Labeled buttons on the remote control are used to define operating settings for training scenarios and,
while training is in progress, pause Trainer operation or interrupt preset training scenarios. Optional
operating settings offer flexibility and a variety of potential setup configurations.
The Trainer and remote control are intended for indoor use under normal room temperature and lighting
conditions.
Note: The Trainer does not provide training for the defibrillator data management functions.
UNPACKING AND INSPECTING THE LIFEPAK CR–T AED TRAINER
After receiving the LIFEPAK CR–T AED Trainer, carefully remove the Trainer and the operating
instructions from the shipping container. Examine the Trainer and accessories for any sign of damage
during shipping.
Shipping container contents include:
•
•
•
•
•
•
LIFEPAK CR–T AED Trainer
QUIK-PAK™ training electrodes
Yellow plastic shock key cover
Remote control
Remote control cable
CHARGE-PAK™ Trainer
•
•
•
•
•
•
Operating instructions
Quick reference card
Soft case with identification card
Lid labels (international trainers only)
4 D-cell alkaline batteries (for Trainer)
2 AAA alkaline batteries (for remote control)
If any components are missing or the Trainer appears to be damaged, contact your dealer or local
Medtronic representative right away. Save the container for reshipping the Trainer if necessary.
Note: Always place the Trainer in a location separate from the defibrillator to avoid confusion in
real emergencies.
2
LIFEPAK CR–T Trainer Operating Instructions
Getting Started
Getting Started
CONTROLS, INDICATORS, AND LABELS
There are several important controls, indicators, and labels on the LIFEPAK CR–T AED Trainer with
which you should become familiar.
Outside Controls, Indicators, and Labels
The outside controls, indicators, and labels are identified in Figure 1 and Figure 2 and described in
Table 1 and Table 2.
1
2
6
3
7
4
5
Top
Bottom
Figure 1 LIFEPAK CR–T AED Trainer Outside Controls, Indicators, and Labels (Top and Bottom)
Table 1 Outside Controls, Indicators, and Labels (Top and Bottom)
1 Carrying handle
The carrying handle is used to transport the Trainer.
2 Readiness display
This display simulates whether the defibrillator is ready for use or needs
attention. The remote control and CHARGE-PAK activate the following
indicators:
OK
OK indicator. Simulates that the defibrillator is ready for use.
CHARGE-PAK indicator. Simulates that the CHARGE-PAK
needs to be replaced or is not installed.
Attention indicator. Simulates that the internal battery of the
defibrillator is low.
Wrench indicator. Simulates that there is a condition that
prevents or could prevent normal operation of the defibrillator.
Service is required.
3 Lid
The top of the Trainer. After the lid is open, the Trainer begins training
scenarios. When the lid is closed, the Trainer simulates the defibrillator
in OFF status.
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
3
Getting Started
Table 1 Outside Controls, Indicators, and Labels (Top and Bottom) (Continued)
4 CHARGE-PAK Trainer
The CHARGE-PAK Trainer is not functional. It is used only to
demonstrate how to remove and replace the CHARGE-PAK.
5 Lid release/On-Off
button
Button that opens the Trainer lid and simulates turning on the
defibrillator. Pressing this button for approximately 2 seconds after the
lid is open simulates turning off the defibrillator.
6 Storage compartment
Storage compartment for the remote control cable and shock button
cover.
7 Battery compartment
Compartment that holds four D-cell alkaline batteries.
11
8
9
12
10
Back
Side
14 13
Figure 2 LIFEPAK CR–T AED Trainer Outside Controls, Indicators, and Labels (Back and Side)
Table 2 Outside Controls, Indicators, and Labels (Back and Side)
8 Remote control signal
sensor
Sensor used for wireless remote control operation. The signal from the
remote control must be detected at this sensor for proper
communication.
9 Light emitting diode
(LED) display
Display containing ten LED bars that are viewed to confirm selections
when operating settings are changed. The LED display is also used to
verify volume level when the volume is adjusted.
10 Remote control
compartment
Storage compartment for the remote control.
11 Software download
receptacle
Connection point for loading software to the Trainer.
12 Remote control
receptacle
Connection point for the remote control cable.
13 Master power switch
Press and release switch that provides power to the Trainer.
14 CHARGE-PAK Trainer
compartment
Compartment that accommodates the removable CHARGE-PAK
Trainer.
4
LIFEPAK CR–T Trainer Operating Instructions
Getting Started
Getting Started
Inside Features
When the Trainer lid is opened, you will see the electrode packet and the release handle shown in
Figure 3. Figure 4 shows the features you see after releasing the electrode packet. Table 3 and Table 4
describe the inside features shown in Figure 3 and Figure 4.
15
16
17
18
19
Figure 3 LIFEPAK CR–T AED Trainer Inside Features
Table 3 Inside Features
15 Quick reference card
An illustrated and condensed guide for using the Trainer.
16 Use By date
Use By date shown: yyyy-mm-dd. This simulated date is visible when
the plastic lid is open or closed.
17 QUIK-PAK electrode
packet
Packet that holds a set of training electrode pads.
18 Electrode packet release Pulling this red handle tears open the training electrode packet and
releases the training electrode pads.
handle
19 Electrode packet anchor
pin
Pin that secures the training electrode packet to the Trainer.
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
5
Getting Started
25
20
21
24
23
22
Figure 4 Inside Features after Opening the Electrode Packet
Table 4 Inside Features after Opening the Electrode Packet
20 Speaker
Speaker that projects the voice prompts and tones.
21 Electrode pad indicators
Indicators that automatically flash red when the Trainer lid is opened,
alerting the trainee that the electrode pads are NOT applied to the
training manikin.
Indicators turn solid green when the instructor presses the ELECTRODE
PADS button to indicate the electrode pads were properly applied during
the training scenario.
Refer to page 10 for information about using the ELECTRODE PADS
button.
22 Training electrode pads
Training electrode pads to be applied to the training manikin.
23 Blue plastic
Blue plastic liner that protects the adhesive until the electrode pads are
used.
24 Training shock button
Pressing this red flashing button simulates the delivery of a shock by the
defibrillator semiautomatic model. (The trainee cannot deliver a
simulated shock unless a Trainer voice prompt instructs them to do so.)
When training simulates the defibrillator automatic model, cover this
button with the yellow shock button cover.
25 Electrode connector
6
Connects the electrode pads to the Trainer. The connection is not
functional—simulated connection/disconnection is initiated by means of
the remote control.
LIFEPAK CR–T Trainer Operating Instructions
Getting Started
Getting Started
Remote Control and Remote Control Cable
The remote control is stored in the remote control compartment (refer to page 4). The dual-function
keys are used to configure the Trainer operating settings prior to a training session and to alter
simulation during training scenarios. The remote control communicates with the Trainer through signals
to the infrared sensor located in the back of the Trainer.
The remote control cable, stored in the storage compartment (refer to pages 3 and 4), can be used as
an alternative to the infrared sensor. Refer to Section 2, beginning on page 9, for information about
connecting the remote control cable.
Figure 5 shows the remote control and remote control cable with the features identified in Table 5.
Remote control button functions are described in Section 2, beginning on page 10.
1
2
3
4
5
6
7
8
9
14
11
10
12
13
Figure 5 Remote Control and Remote Control Cable
Table 5 Remote Control Features (Setup Functions)
1 Feature not available (F1)
8 Pause button (C2)
2 Electrode pads button (F2)
9 Volume control button (OP) (L)
3 No advised shock button (T1)
10 Green select button
4 CHARGE-PAK button (F3)
11 Red select button
5 Service button (F4)
12 Up arrow button
6 Attention button (T2)
13 Right arrow button
7 Motion button (C1)
14 Remote control cable
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
7
Getting Started
INSTALLING AND REPLACING BATTERIES
The following paragraphs provide the procedures for installing or replacing LIFEPAK CR–T AED Trainer
and remote control batteries.
Installing and Replacing Trainer Batteries
Four D-cell alkaline batteries provide power to the Trainer. The batteries are installed in a compartment
in the bottom of the Trainer. Fresh batteries provide approximately 100 hours of continuous Trainer
operation.
To install the batteries:
1 Verify that power to the Trainer has been turned off (using the MASTER POWER switch).
2 Carefully turn the Trainer upside down.
3 Remove the battery compartment cover by depressing both latches on the cover and lifting the
cover.
4 Insert four fresh, identical batteries, taking care to align the (+) and (-) terminals correctly. The
correct battery placement is shown in Figure 6.
5 Replace the cover and press down until you hear the latches snap into place.
Note: Always replace all of the batteries at the same time. Always use four identical batteries.
Note: For permanent storage (longer than six months), remove the batteries from the battery
compartment. If the Trainer is used infrequently (approximately once every six months), the
batteries can remain in the battery compartment.
Installing and Replacing Remote Control Batteries
Two AAA alkaline batteries provide power to the remote control. The batteries are located in a
compartment on the bottom of the remote control. (See Figure 6.)
To replace the remote control batteries:
1 Turn the remote control upside down.
2 Open the battery compartment by sliding the battery compartment cover down with firm thumb
pressure.
3 Insert two fresh, identical batteries, taking care to align the (+) and (-) terminals correctly.
4 Replace the battery compartment cover, sliding it up until it snaps securely into place.
–
+
D-Cell
–
D-Cell
+
–
D-Cell
+
AAA
–-
D-Cell
AAA
+
Figure 6 LIFEPAK CR–T AED Trainer and Remote Control Battery Placement
8
LIFEPAK CR–T Trainer Operating Instructions
Using the LIFEPAK CR–T AED Trainer
2 USING THE LIFEPAK CR–T AED TRAINER
This section provides information and instructions for using the LIFEPAK CR–T AED Trainer.
Voice Prompts and Tones
Using the Remote Control
Preparing for a Training Session
Conducting a Training Session
Following a Training Session
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
page 10
10
12
13
14
9
Using the LIFEPAK CR–T AED Trainer
VOICE PROMPTS AND TONES
The LIFEPAK CR–T AED Trainer voice prompts provide the trainee with step-by-step instructions for
responding to training scenarios. For a complete list of voice prompts, refer to Appendix A.
USING THE REMOTE CONTROL
The remote control allows the instructor to:
•
•
•
•
Preset operating settings in a setup configuration (refer to Section 3, beginning on page 15).
Pause LIFEPAK CR–T AED Trainer operation.
Interrupt preset routines with NO SHOCK ADVISED, CHECK PADS FOR GOOD CONTACT, MOTION, and LOW
BATTERY.
Select any one of the six available shock protocols.
The remote control communicates with the Trainer by using wireless infrared signals or the remote
control cable. The signal indicator acknowledges remote control signals received, both with and without
the remote control cable.
•
•
•
One red flash indicates that a signal was received from the remote control and that the Trainer is
responding accordingly.
Three red flashes indicate that an invalid remote control key was pressed and that Trainer operation
is unchanged.
A continuous red light indicates that the Trainer is in pause mode.
To use the remote control without the cable, the instructor must stand behind the Trainer. During use,
the instructor must hold the remote control level rather than aiming it directly at the Trainer.
Remote Control Functions
Remote control button functions are described in Table 6. The Trainer is designed for maximum
flexibility. Your defibrillator may not have all of the functions identified in Table 6.
Refer to Section 3, Setup Configuration and Operating Settings or a description of the alternate remote
control functions, for example, F1.
Table 6 Remote Control Button Functions
Button
F1
F2
Function
Feature not available
Simulates electrode
pads application
Operation and Description
Refer to Section 3, Setup Configuration and Operating Settings.
The ELECTRODE PADS button is used to indicate whether or not
the electrode pads are properly applied to the manikin.
After the trainee applies the electrode pads to the manikin,
press the ELECTRODE PADS button to change the ELECTRODE PAD
indicators to solid green. Press the ELECTRODE PADS button a
second time to initiate the CHECK PADS FOR GOOD CONTACT
voice prompt and to change the ELECTRODE PAD indicators to
flashing red, indicating that the training electrodes were not
applied properly or were disconnected after they were properly
applied. Press the ELECTRODE PADS button a third time after the
training electrodes are properly applied to continue the training
scenario.
10
LIFEPAK CR–T Trainer Operating Instructions
Using the LIFEPAK CR–T AED Trainer
Table 6 Remote Control Button Functions (Continued)
Button
T1
Function
Change shock to no
shock advised
Operation and Description
The NO SHOCK ADVISED button can be used only during
simulated analysis.
Press the NO SHOCK ADVISED button to change any shock within
a shock protocol to NO SHOCK ADVISED.
F3
Simulates the
CHARGE-PAK needs to
be replaced
The CHARGE-PAK button can be used only when the Trainer is in
simulated OFF status (MASTER POWER switch ON, LID
RELEASE/ON-OFF button OFF).
Press the CHARGE-PAK button once to activate the CHARGE-PAK
indicator in the readiness display.
To clear the CHARGE-PAK indicator from the readiness display,
remove and replace the CHARGE-PAK. The instructor can also
clear the indicator by pressing the button a second time.
F4
Simulates a call for
service situation
The WRENCH button can be used only when the Trainer is in
simulated OFF status.
Press the WRENCH button once to activate the wrench indicator
in the readiness display.
To clear the WRENCH indicator from the readiness display, press
the button a second time.
T2
Attention
The ATTENTION button can be used when the Trainer is ON and
when it is in simulated OFF status.
Press the ATTENTION button once to activate the ATTENTION
indicator in the readiness display. This simulates a low internal
battery condition (simulating a situation in which the actual
defibrillator would have a minimum of 6 shocks or 42 minutes of
monitoring time available for use).
To clear the ATTENTION indicator from the readiness display,
press the ATTENTION button a second time.
C1
C2
Start or stop simulated
motion
Pause
The MOTION button is used only during simulated analysis.
Press the MOTION button to start simulated motion. The Trainer
interrupts simulated analysis and delivers MOTION DETECTED
prompts for 10 seconds or until the instructor presses the
MOTION button again.
The PAUSE button suspends the Trainer in its present state and
causes the LED display to illuminate red until operation is
resumed. This allows the instructor to interject other instruction,
if necessary. The Trainer will pause for approximately
30 minutes before it turns completely off.
Pressing the PAUSE button a second time resumes Trainer
operation.
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
11
Using the LIFEPAK CR–T AED Trainer
The CHARGE-PAK indicator automatically appears on the
readiness display after simulating a patient use.
Using the LIFEPAK CR–T AED Trainer
Table 6 Remote Control Button Functions (Continued)
Button
OP
Function
L Adjust volume of voice
prompts
Operation and Description
Each time the Trainer is turned on, the volume level defaults to
the level used during the previous session.
Three volume levels are available (low, medium, high). Press the
VOLUME CONTROL button to select the volume level desired. As
you press the button, the volume increases. View the LED
display to observe volume changes. When the highest volume is
reached, the next press returns the volume to low.
GREEN SELECT button
The GREEN SELECT button is used to change the shock protocol
and general operating setting options.
When the GREEN SELECT button is pressed, the LED display
flashes green to indicate setup mode is activated.
Press the GREEN SELECT button twice to display the shock
protocol.
For more information, refer to Section 3, beginning on page 15.
RED SELECT button
The RED SELECT button is used to change CPR Time 1,
CPR Time 2, and the Language Option.
When the RED SELECT button is pressed, the LED display flashes
red to indicate setup mode is activated.
For more information, refer to Section 3, beginning on page 15.
UP ARROW button
RIGHT ARROW button
The UP ARROW button is used to select a setting option.
The RIGHT ARROW button is used to advance through the
settings.
Using the Remote Control Cable
To use the remote control cable, insert the cable’s right-angle connector into the remote control
receptacle. Insert the connector on the opposite end of the cable into the receptacle located on the side
of the Trainer (see Figure 2, page 4).
Disconnect the remote control cable by grasping the connector on the side of the Trainer and gently pulling
away from the Trainer. Disconnect the right-angle connector from the remote control in the same way.
PREPARING FOR A TRAINING SESSION
1 Connect the electrode packet to the Trainer as follows:
– Press the LID RELEASE/ON-OFF button to open the Trainer lid.
– Insert the electrode pads connector into the Trainer cable receptacle until it snaps into place
(see Figure 7).
– Insert the black plastic anchor pin on the electrode packet into the anchor receptacle at the upper
left corner of the Trainer (see Figure 7).
– Ensure that the lower edge of the packet is under the fin on the lower front part of the Trainer.
– After the electrode packet is in place, close the Trainer lid.
12
LIFEPAK CR–T Trainer Operating Instructions
Using the LIFEPAK CR–T AED Trainer
2 Slide and release the MASTER POWER switch to provide power to the Trainer.
3 Check to confirm that the existing setup configuration is appropriate for the training scenario. If not,
change the setup configuration as desired (refer to Section 3, beginning on page 15 for setup
information).
4 If preparing for a training session on the automatic model of the defibrillator, place the yellow plastic
cover, stored in the storage compartment (refer to pages 3 and 4), over the SHOCK button.
Two Quick Start Reference Cards are provided in Appendix B, beginning on page 33. These cards
include a condensed description of the steps to complete when preparing the Trainer for a training
scenario. The cards are perforated for easy removal and may be photocopied.
Using the LIFEPAK CR–T AED Trainer
Figure 7 Connecting the Training Electrode Packet to the LIFEPAK CR–T AED Trainer
CONDUCTING A TRAINING SESSION
1 Verify that power to the Trainer is on and the OK indicator appears in the readiness display.
2 Proceed with the training session.
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
13
Using the LIFEPAK CR–T AED Trainer
Note: Ensure that the trainee does not touch the adhesive on the QUIK-PAK training electrodes or
allow a training electrode to fold over on itself. Also ensure that the training electrodes are correctly
oriented on the manikin as shown on the electrode packet (see Figure 8).
Figure 8 Placing Training Electrodes on the Manikin
Note: If the QUIK-PAK training electrodes accidentally detach from the manikin or disconnect from
the Trainer, the CHECK PADS FOR GOOD CONTACT voice prompt will not sound. The instructor must
press the ELECTRODE PADS button on the remote control to indicate that the electrode pads are
disconnected.
3 Upon ending a training scenario, press the lid release/ON-OFF button or close the Trainer lid to
simulate turning off the defibrillator. The CHARGE-PAK indicator automatically appears on the
readiness display. To clear this indicator, the trainee must remove and reinsert the CHARGE-PAK or
the instructor must press the CHARGE-PAK button (F3).
FOLLOWING A TRAINING SESSION
1 Remove the training electrodes from the manikin by grasping the electrode pad at the cable end and
peeling it away from the manikin at a 45° angle. Do not remove the training electrodes from the
manikin by pulling on the cable.
2 Reassemble the QUIK-PAK training electrode packet for the next training session.
3 Slide and release the MASTER POWER switch to turn off the Trainer. (The Trainer automatically turns
off after 15 minutes of inactivity.)
4 Care for the Trainer as appropriate (refer to Section 4, beginning on page 23).
Note: Always place the Trainer in a location separate from the defibrillator to avoid confusion in
real emergencies.
14
LIFEPAK CR–T Trainer Operating Instructions
3 SETUP
This section provides setup configuration instructions for the LIFEPAK CR–T AED Trainer. It also
identifies default settings and describes the setting options, including the procedures for changing those
setting options.
Setup Configuration and Operating Settings
Changing Options for Operating Settings
page 16
18
Setup
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
15
Setup
SETUP CONFIGURATION AND OPERATING SETTINGS
Table 7 lists the operating settings for the LIFEPAK CR-T AED Trainer setup configuration, describes
the options for each setting, and identifies the preset default for each setting. Your defibrillator may not
have all of the functions identified in Table 7.
Table 7 Trainer Operating Setting Options
Operating Settings
Options/Description
Default Setting
SHOCK PROTOCOL
There are six shock protocol options available:
Custom #1
•
•
Four protocols (F1 through F4) are preset and cannot
be modified during setup.
Two protocols (C1 and C2) can be user-defined or
customized by the instructor.
Note regarding
Shock Protocol and
Stack Shocks
settings:
When Stack Shocks is OFF, each shock/no shock decision
is followed by an interval of CPR (interval = time).
•
F1 - Fixed #1
One SHOCK ADVISED followed by three NO SHOCK ADVISED
decisions.
•
F2 - Fixed #2
Two SHOCK ADVISED followed by two NO SHOCK ADVISED
decisions.
•
F3 - Fixed #3
One NO SHOCK ADVISED, followed by one SHOCK ADVISED,
followed by two NO SHOCK ADVISED decisions.
•
F4 - Fixed #4
Four NO SHOCK ADVISED decisions.
•
C1 - Custom #1
Defined by instructor (refer to page 3-19).
When Stack Shocks is ON, each series of consecutive
shocks will be followed by an interval of CPR (refer to the
CPR time settings on page 3-17.
Nine consecutive
SHOCK ADVISED
decisions
•
C2 - Custom #2
Defined by instructor (refer to page 3-19).
Nine consecutive
NO SHOCK
ADVISED
decisions
START PROMPT
When the Trainer lid is opened, two beeping tones confirm
that the Trainer is turned ON and that a training scenario
has begun. A CALL FOR HELP voice prompt can be added
following the beeping tones.
Voice prompt on
PULSE PROMPTS
Three signs of life voice prompt options are available.
CHECK FOR
PULSE
•
CHECK FOR PULSE
This prompt is for the more advanced trainee to check for a
pulse.
•
CHECK FOR
BREATHING
This prompt is for the lay trainee to check for signs of
breathing.
•
CHECK FOR SIGNS
OF CIRCULATION
This prompt is for the lay trainee to check for signs of
circulation.
16
LIFEPAK CR–T Trainer Operating Instructions
Setup
Table 7 Trainer Operating Setting Options (Continued)
Operating Settings
Options/Description
AUTOMATIC/
SEMIAUTOMATIC
MODEL
The Trainer can be set up to simulate a defibrillator,
automatic model (no SHOCK button) or semiautomatic
model (SHOCK button).
•
Automatic
The Trainer automatically delivers a simulated shock. The
shock button cover is stored in the storage compartment
(refer to pages 3 and 4).
•
Semiautomatic
The trainee must press the Trainer SHOCK button to deliver
a simulated shock.
CPR TIME
•
CPR Time 1
CPR Time is the time interval allowed between Trainer
prompts to perform CPR. Seven CPR time intervals (in
seconds) are available for CPR Time 1 and CPR Time 2:
15, 30, 45, 60, 90, 120, 180.
Default Setting
Semiautomatic
120 seconds *
With Stack Shocks OFF: Occurs after every shock.
With Stack Shocks ON: Occurs after a series of
consecutive shocks (stack) and after the first NSA that
follows a shock series.
•
CPR TIme 2
Occurs after all other NSA conditions.
STACK SHOCKS
Stack Shocks can be set to ON or OFF.
•
ON
The Trainer follows a traditional stacked shock protocol and
delivers up to three consecutive SHOCK ADVISED, as
necessary, without interposed CPR.
•
OFF
Allows for an increased emphasis on CPR by prompting the
responder to provide CPR after each SHOCK ADVISED.
Pulse Check can be set to NEVER, AFTER EVERY NSA, AFTER
SECOND NSA, or ALWAYS.
•
NEVER
Increases the time allowed for CPR by removing the prompt
to perform a pulse check after a SHOCK ADVISED and after a
NO SHOCK ADVISED.
•
AFTER EVERY
NSA
Prompts to perform a pulse check after every NO SHOCK
ADVISED.
•
AFTER SECOND
NSA
Only prompts to perform a pulse check after the second
NO SHOCK ADVISED and every NO SHOCK ADVISED after that.
•
ALWAYS
NEVER *
Setup
PULSE CHECK
OFF *
Prompts for a pulse check to be performed after every
SHOCK ADVISED and after every NO SHOCK ADVISED
decision.
LANGUAGE OPTION
This option allows you to select the language spoken for
voice prompts. Refer to Table 10 for available settings.
English
*These default settings are consistent with the 2005 AHA Guidelines for Cardiopulmonary Resuscitation and
Emergency Cardiac Care:
• CPR time = 2 minutes
• One-shock strategy, followed by CPR
• Removal of Pulse Check prompt
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
17
Setup
CHANGING OPTIONS FOR OPERATING SETTINGS
The following paragraphs describe how to change the operating settings identified in Table 7. Included
are paragraphs that discuss using the remote control and LED display when making changes and
paragraphs that explain the procedural steps for completing the changes.
Using the Remote Control and the LED Display
To make changes to the operating settings, you must use the remote control (shown previously in
Figure 5, page 7) and the Trainer LED display.
Before you perform any of the procedures for changing operating settings, complete these steps:
1 If the Trainer is completely turned off, press the MASTER POWER switch forward and release it to
provide power to the Trainer.
2 Stand behind the Trainer and hold the remote control level, unless the remote control cable is
connecting the remote control and the Trainer.
3 As you complete the steps in the procedures that follow, view the LED display to ensure that the
correct bars and colors illuminate.
Note: The LED bars illuminate until you save the setting and continue to the next action.
Figure 9 shows the LED display with its ten LED bars blank. Each bar corresponds to a setting function
and illuminates when you initiate a change.
1 2 3 4
5 6 7 8 9 0
Figure 9 LED Display
Procedures for Changing Operating Settings
The following paragraphs provide the procedural steps for changing operating settings. The procedures
address Shock Protocol, General Operating Settings (including Start Prompt, Pulse Prompts, and
Automatic/Semiautomatic Model), CPR Time, and the Language Option.
Shock Protocol
For most training scenarios, it is easiest to set up the shock protocol before the training session when
the Trainer is in simulated OFF status (MASTER POWER switch ON, LID RELEASE/ON-OFF button OFF).
Selecting Shock Protocols
To select one of the fixed shock protocols, F1 through F4, or custom shock protocols, C1 or C2:
1 Press the GREEN SELECT button.
2 Refer to Table 8 to determine which protocol you want to enter and then press the appropriate
button.
3 Press the GREEN SELECT button to save the selection. The signal sensor flashes, indicating the
selection is saved, and the Trainer enters a simulated OFF status.
18
LIFEPAK CR–T Trainer Operating Instructions
Setup
Table 8 Shock Protocol Options
Button
Shock Protocol
Order
F1
Fixed #1
SNNN
LED Display*
1 2 3 4 5 6 7 8 9 0
F2
Fixed #2
SSNN
1 2 3 4 5 6 7 8 9 0
F3
Fixed #3
NSNN
1 2 3 4 5 6 7 8 9 0
F4
Fixed #4
NNNN
1 2 3 4 5 6 7 8 9 0
C1
Custom #1
SSSSSSSSS
1 2 3 4 5 6 7 8 9 0
C2
Custom #2
NNNNNNNNN
1 2 3 4 5 6 7 8 9 0
*
= Shock (Green)
= No Shock (Red)
= End Scenario (Blank)
Configuring Shock Protocols
You can change the Custom #1 and Custom #2 shock protocols to any configuration of SHOCK and
NO SHOCK ADVISED prompts, up to nine selections.
To change Custom #1 and Custom #2 shock protocols:
1 Press the GREEN SELECT button.
2 Press either the MOTION button (C1) for Custom #1 or the PAUSE button (C2) for Custom #2.
3 Press the UP S ARROW button to select shock or no shock. The first bar can be set only to shock or
no shock.
Setup
4 Press the RIGHT X ARROW button to advance to the next bar and press the UP S ARROW button to
select shock or no shock.
5 Repeat Step 4 until you have set the scenario you want to demonstrate and then press the UP S
ARROW button until remaining LED bars turn blank.
6 Press the GREEN SELECT button to save the change. The signal sensor flashes, indicating the change
has been saved. The Trainer enters simulated OFF status.
Figure 10 shows the LED displaying the following shock protocol: Bar 1, no shock (red); Bar 2, shock
(green); Bar 3, no shock (red); Bar 4, shock (green); Bar 5, end scenario (blank).
Bar Number
1
2
3
4
5
6
7
8
9
0
Figure 10 Custom #1 and #2 Options
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
19
Setup
General Operating Settings
The procedure for changing the general operating settings (Start Prompt, Stack Shocks, Pulse Check,
Pulse Prompts, and Automatic/Semiautomatic Model) is the same for each. Table 9 identifies each
general operating setting, indicates the LED bar that corresponds to the setting, and describes the
options available.
Table 9 General Operating Setting Options
Operating Setting
Bar Number
Options
Automatic/Semiautomatic
Model
1
Green = Semiautomatic; Red = Automatic
Start Prompt
2
Green = Voice ON; Red = Voice OFF
Stack Shocks
3
Green = OFF; Red = ON
Pulse Check
4, 5
Pulse Prompts
Green, Green = NEVER
Red, Red = ALWAYS
Yellow, Yellow = AFTER 2ND NSA
Green, Yellow = AFTER EVERY NSA
6
Green = CHECK FOR PULSE
Red = CHECK FOR BREATHING
Yellow = CHECK FOR SIGNS OF CIRCULATION
To change the general operating settings:
1 Press the GREEN SELECT button.
2 Press the VOLUME button (OP, L).
3 Press the RIGHT X ARROW button to advance to the desired operating setting (LED bar number).
4 Press the UP S ARROW button to select the desired option (LED bar color).
5 Repeat steps 3 and 4 until you have changed all of the desired operating settings.
6 After making your changes, press the GREEN SELECT button to save the selections. The signal sensor
flashes, indicating the selections have been saved. The Trainer enters simulated OFF status.
Figure 11 shows the LED displaying the following option settings:
•
•
•
•
Bar 1, Automatic/Semiautomatic Model: Semiautomatic (green)
Bar 2, Start Prompt: Voice ON (green)
Bar 3, Stack Shocks ON (red)
Bars 4 and 5, Pulse Check OFF (green, green)
Bar Number
1
2
3
4
5
6
7
8
9
0
Figure 11 General Operating Setting Options
20
LIFEPAK CR–T Trainer Operating Instructions
Setup
CPR Time
To change CPR Time 1 or CPR Time 2:
1 Press the RED SELECT button.
2 Press the NO SHOCK ADVISED button (T1) for CPR Time 1 and then proceed with steps 3 and 4.
–or–
Press the ATTENTION button (T2) for CPR Time 2 and then proceed with steps 3 and 4.
3 Press the RIGHT X ARROW button to advance through the possible CPR time intervals. (Each bar
illuminates red as you advance to it.)
4 When the bar corresponding to the desired time illuminates red, press the RED SELECT button to save
the selection. The signal sensor flashes, indicating that the selection has been saved. The Trainer
enters simulated OFF status.
Figure 12 shows the LED displaying the CPR Time set to 90 seconds.
CPR Time
Bar Number
15 30 45 60 90 120 180
1
2
3
4
5
6
7
8
9
0
Figure 12 CPR Time Options
Language Option
You can set the voice prompts to be delivered in any of up to six languages, depending on the language
group ordered with your Trainer. There are nine language groups available. Table 10 lists the language
groups and the languages available in each group.
Table 10 Language Groups
Bar 2
Bar 3
Bar 4
Bar 5
Group 1
English
Norwegian
Danish
Swedish
Finnish
Group 2
English
German
French
Dutch
Group 3
English
Polish
Hungarian
Czech
Group 4
English
Japanese
Cantonese
Mandarin
Group 6
English
Group 7
English
Italian
Spanish
Group 8
English
Iberian
Spanish
Portuguese
Icelandic
Group 9
English
Romanian
Lithuanian
Hebrew
Bar 6
Setup
Configuration Bar 1
Russian
Slovak
Slovenian
To change the language option:
1 Press the RED SELECT button.
2 Press the VOLUME CONTROL button (OP, L).
3 Press the RIGHT X ARROW button until the desired bar illuminates red.
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
21
Setup
4 Press the RED SELECT button to save the selection. The signal sensor flashes, indicating that the
selection has been saved. The Trainer enters simulated OFF status.
Setup
Figure 13 shows an example of a Trainer configured with Group 1, and the desired language is Finnish.
Option
1
2 3 4
5
6
Bar Number
1
2 3 4
5
6
7
8 9
0
Figure 13 Language Options
Resetting Default Settings
To reset all settings to the original factory default, hold the MASTER POWER switch to ON for at least five
seconds. Four yellow bars will appear when the reset is complete.
22
LIFEPAK CR–T Trainer Operating Instructions
Caring for the LIFEPAK CR–T AED Trainer
4 CARING FOR THE LIFEPAK CR–T AED TRAINER
This section provides information about caring for the LIFEPAK CR–T AED Trainer.
Replacing Batteries
Troubleshooting
Cleaning
Product Recycling Information
Warranty
Accessories
Specifications
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
page 24
24
26
26
26
27
27
23
Caring for the LIFEPAK CR–T AED Trainer
REPLACING BATTERIES
When batteries for the LIFEPAK CR–T AED Trainer or the remote control become depleted or
damaged, they should be replaced immediately. Refer to Section 1, page 8 for procedures detailing the
steps for installing and replacing batteries in the Trainer and the remote control.
TROUBLESHOOTING
Tables 11 through 15 provide checklists for troubleshooting LIFEPAK CR–T AED Trainer operating
problems. If you cannot correct a problem, discontinue using the Trainer until the problem is resolved.
Contact your local Medtronic representative.
Note: Do not disassemble the Trainer. There are no operator-serviceable components and
operator disassembly may void the warranty.
Table 11 Voice Prompts and Tones Troubleshooting
Observation
Possible Cause
Low volume; Trainer remains
functional
•
•
D-cell batteries are low •
Speaker grill partially
•
covered
Replace D-cell batteries.
Remove obstruction.
Three beeping tones sound when
the Trainer is turned OFF
•
D-cell batteries are low •
Replace D-cell batteries
immediately.
No sound; Trainer remains
functional
•
•
Speaker grill covered
Speaker damaged
•
•
Remove blockage.
Contact your local Medtronic
representative.
No sound; Trainer does not
function
•
D-cell batteries
depleted or damaged
Trainer damaged
•
Replace D-cell batteries.
•
Contact your local Medtronic
representative.
•
Corrective Action
Table 12 LED Display Troubleshooting
Observation
Possible Cause
Corrective Action
Intensity is fading (or inconsistent)
•
Low battery
•
Replace D-cell batteries.
Unlit when MASTER POWER switch
pressed; Trainer does not function
•
D-cell batteries
depleted or damaged
Trainer damaged
•
Replace D-cell batteries.
•
Contact your local Medtronic
representative.
Trainer detects
interference
Remote control
operation not
appropriate
•
Check for possible obstruction.
•
Install remote control cable to
improve connection.
•
LED display scrolls yellow light
back and forth
•
•
24
LIFEPAK CR–T Trainer Operating Instructions
Caring for the LIFEPAK CR–T AED Trainer
Observation
Possible Cause
Corrective Action
Voice prompts are out of sequence •
Incorrect operating
setting options
selected
•
Review setup procedures in
Section 3, beginning on page 15.
Voice prompts are incomplete
•
Trainer damaged
•
Contact your local Medtronic
representative.
CONNECT ELECTRODES sequence
•
Instructor did not press •
remote control to begin
scenario sequence
Damaged remote
•
control
Infrared sensor not
•
working properly
•
•
repeats after training electrodes
are connected to the Trainer
•
•
Press the ELECTRODE PADS button
once on the remote control to
initiate voice prompts.
Contact your local Medtronic
representative.
Clean or clear the signal sensor, if
obstructed.
Install remote control cable.
Contact your local Medtronic
representative.
Table 14 Remote Control Troubleshooting
Observation
Possible Cause
Trainer does not respond to remote •
control button presses
Infrared sensor is not
receiving remote
control signal
Corrective Action
•
•
Reposition remote control relative
to the Trainer.
Remove anything blocking the
signal sensor.
Install remote control cable.
•
•
D-cell batteries
depleted or damaged
•
Replace D-cell batteries.
•
Remote control
damaged
•
Replace remote control.
•
Remote control
batteries low
•
Replace remote control batteries.
Table 15 Training Electrodes Troubleshooting
Observation
Possible Cause
Corrective Action
Training electrode pads do not
adhere to manikin
•
Adhesive
contaminated
•
Replace training electrode
packet.
Training electrode connector will
not plug into the Trainer
•
Training electrode
connector damaged
Trainer electrode
receptacle damaged
•
Replace training electrode
packet.
Contact your local Medtronic
representative.
•
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
•
25
Caring for the LIFEPAK CR–T AED Trainer
Table 13 Setup Options Troubleshooting
Caring for the LIFEPAK CR–T AED Trainer
CLEANING
Clean the Trainer, remote control, and the remote control cable by wiping surfaces with one of the
following:
•
•
A lint-free, slightly damp cloth moistened with mild soap and water.
A lint-free, slightly damp cloth moistened with denatured alcohol.
Observe the following precautions when cleaning:
•
•
•
Do not immerse or soak the Trainer, remote control, or the cable.
Do not use bleach, bleach dilution, or phenolic compounds.
Do not steam or gas sterilize.
PRODUCT RECYCLING INFORMATION
Recycle the Trainer and its accessories at the end of their useful life.
Recycling Assistance
Items should be recycled according to national and local regulations. Contact your local Medtronic
representative for assistance.
Preparation
Items should be clean and contaminant-free prior to being recycled.
Recycling of Training Electrodes
After training electrodes have reached the end of their useful life, follow your local clinical procedures for
recycling.
Packaging
Packaging should be recycled according to national and local regulations.
WARRANTY
In the USA, call 1.800.442.1142. Outside the USA, contact your local Medtronic representative for
warranty information.
26
LIFEPAK CR–T Trainer Operating Instructions
Caring for the LIFEPAK CR–T AED Trainer
Caring for the LIFEPAK CR–T AED Trainer
ACCESSORIES
The following accessories are available for the LIFEPAK CR–T AED Trainer:
Table 16 LIFEPAK CR–T AED Trainer Accessories
Accessory
Part Number
QUIK-PAK Training Electrode Packet
3201805
Shock Button Cover
3201801
Remote Control and Cable
3201799
Serial Cable
3206630
CHARGE-PAK Trainer
3201800
Quick Reference Card
3201508
Soft Case
3201803
Soft Case Cards
3201792
International Lid Labels
3201755
SPECIFICATIONS
Table 17 lists the specifications for the LIFEPAK CR–T AED Trainer. Table 18 lists the specifications for
the remote control.
Table 17 LIFEPAK CR–T AED Trainer Specifications
General
Device designed for low impact, low stress environments. For use in
temperature-controlled areas protected from precipitation. Capable of
withstanding heavy usage and prolonged periods of operation.
Physical Characteristics
Height: 10.7 cm (4.2 in.)
Width: 20.3 cm (8.0 in.)
Depth: 24.1 cm (9.5 in.), excluding handle
Weight: 2.1 kg (4.6 lb) with batteries
Batteries
6 volts/4 cells, range 3.4 Vdc ~ 6.5 Vdc
Four non-rechargeable D-cell alkaline batteries. New batteries will
provide not less than 100 hours of continuous operation under normal
indoor-environment conditions.
Buttons
Master Power, lid release/ON-OFF, shock
Speaker
Volume output: Hi, Med., Low
Operating Temperature
3° to 38° C (37° to 100° F)
Storage Temperature
–10° to 60° C (14° to 140° F) (remove batteries for storage)
Water Resistance
Spillage resistance per IEC 601-1, part 44.3
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
27
Caring for the LIFEPAK CR–T AED Trainer
Table 18 Remote Control Specifications
Transmission
Wireless infrared signal. Range, 3 meters max
82-inch (2-meter) optional cable attachment
Size
4.57 cm x 3.38 cm x 1.65 cm (1.8 in. x 1.3 in. x .6 in.)
Weight (without batteries)
32 grams (.08 lb)
Batteries
3 volts supplied from two AAA alkaline batteries
Buttons
13-key membrane switch pad labeled for the following functions:
NO SHOCK, SERVICE REQUIRED, ELECTRODE PAD CONTACT,
MOTION, REPLACE CHARGE-PAK, CPSS, PAUSE, VOLUME
CONTROL, LOW INTERNAL BATTERY, SETUP NAVIGATION
BUTTONS
Operating Temperature
3° to 38° C (37° to 100° F)
Storage Temperature
–10° to 60° C (14° to 140° F) (remove batteries for storage)
Water Resistance
Spillage resistance per IEC 601-1, part 44.3
28
LIFEPAK CR–T Trainer Operating Instructions
APPENDIX A
LIFEPAK CR–T AED TRAINER
VOICE PROMPTS AND TONES
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
0
A
29
Appendixes
Appendixes
LIFEPAK CR–T AED Trainer Voice Prompts and Tones
Table 19 Voice Prompts and Tones
Voice Prompt
Tones
CALL FOR HELP NOW
After the AED Trainer lid opens, two beeping tones
sound. If the start option is set to voice prompts, this
voice prompt will sound following the beeping tones.
REMOVE ALL CLOTHING FROM PATIENT’S CHEST
PULL RED HANDLE TO OPEN BAG
LOOK AT PICTURES ON PADS
PEEL ONE PAD OFF BLUE PLASTIC
Appendixes
APPLY PAD TO BARE SKIN EXACTLY AS SHOWN IN
THE PICTURE
PRESS PAD FIRMLY
PEEL OTHER PAD OFF BLUE PLASTIC
CHECK PADS FOR GOOD CONTACT
CHECK CONNECTOR
DO NOT TOUCH PATIENT –
EVALUATING HEART RHYTHM
Two beeping tones sound to simulate heart rhythm
analysis.
MOTION DETECTED
STOP MOTION
STAND BY
PREPARING TO SHOCK
EVERYONE CLEAR
PRESS FLASHING BUTTON
Semiautomatic model only. An alarm tone sounds until
the SHOCK button is pressed.
DO NOT TOUCH PATIENT –
DELIVERING SHOCK
An alarm tone sounds until the SHOCK button is
pressed (semiautomatic model) or until a simulated
shock is delivered (automatic model).
SHOCK DELIVERED
SHOCK NOT DELIVERED
NO SHOCK ADVISED
PROVIDE CHEST COMPRESSIONS AND RESCUE
BREATHS
CHECK FOR PULSE
IF NO PULSE, PROVIDE CHEST COMPRESSIONS
AND RESCUE BREATHS
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
31
LIFEPAK CR–T AED Trainer Voice Prompts and Tones
Table 19 Voice Prompts and Tones (Continued)
Voice Prompt
Tones
CHECK FOR BREATHING
IF NOT BREATHING, PROVIDE CHEST
COMPRESSIONS AND RESCUE BREATHS
CHECK FOR SIGNS OF CIRCULATION
IF NO SIGNS OF CIRCULATION, PROVIDE CHEST
COMPRESSIONS AND RESCUE BREATHS
CONTINUE CARE
32
LIFEPAK CR–T Trainer Operating Instructions
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
B
33
Appendixes
APPENDIX B
LIFEPAK CR–T AED TRAINER
QUICK START REFERENCE CARD
LIFEPAK® CR–T AED TRAINER
Quick Start Reference Card
Quick Start Setup Procedure
1 Turn on the Trainer using the MASTER POWER switch.
2 Press the GREEN SELECT
button on the remote control.
3 Select the desired shock protocol (the default setting is C1) using the buttons referenced in the following table.
4 Press the GREEN SELECT
button again to confirm shock protocol. The Trainer enters simulated OFF status.
5 You are now ready to begin a training session.
6 When the electrode pads are properly placed on the manikin, press the ELECTRODE PADS
remote control.
button (F2) on the
7 Use the remote control to create troubleshooting situations. Refer to the opposite side of this card for details.
Remote Control Button
AED Trainer Shock Protocol
Shock Order*
F1
Fixed #1
SNNN
F2
Fixed #2
SSNN
F3
Fixed #3
NSNN
F4
Fixed #4
NNNN
C1**
Custom #1
SSSSSSSSS
* S: Shock Advised (green LED)
N: No Shock Advised (red LED)
C2**
Custom #2
NNNNNNNNN
** Custom settings, C1 and C2, may be changed
(refer to operating instructions).
LIFEPAK® CR–T AED TRAINER
Quick Start Reference Card
Quick Start Setup Procedure
1 Turn on the Trainer using the MASTER POWER switch.
2 Press the GREEN SELECT
button on the remote control.
3 Select the desired shock protocol (the default setting is C1) using the buttons referenced in the following table.
4 Press the GREEN SELECT
button again to confirm shock protocol. The Trainer enters simulated OFF status.
5 You are now ready to begin a training session.
6 When the electrode pads are properly placed on the manikin, press the ELECTRODE PADS
remote control.
button (F2) on the
7 Use the remote control to create troubleshooting situations. Refer to the opposite side of this card for details.
Remote Control Button
AED Trainer Shock Protocol
Shock Order*
F1
Fixed #1
SNNN
F2
Fixed #2
SSNN
F3
Fixed #3
NSNN
F4
Fixed #4
NNNN
C1**
Custom #1
SSSSSSSSS
* S: Shock Advised (green LED)
N: No Shock Advised (red LED)
C2**
Custom #2
NNNNNNNNN
** Custom settings, C1 and C2, may be changed
(refer to operating instructions).
LIFEPAK® CR–T AED TRAINER
Quick Start Reference Card
Button
Function
Button
Function
Press to change SHOCK ADVISED to NO SHOCK
ADVISED. Function is active only during simulated
analysis.
Press once to activate the ATTENTION
indicator in the readiness display. To clear,
press the button again.
Press to advance the training electrodes to ON or
OFF.
Press any time to suspend device
operation. Press again to resume operation
at point of interruption.
Press to advance MOTION DETECTED to ON or OFF.
This feature is active during simulated analysis only.
Press to change the speaker volume. The
volume level scrolls up, and returns to
lowest level after the highest is reached.
Press to activate WRENCH indicator on the readiness
display (active only when Trainer is in simulated OFF
status). To clear, press the button again.
Press to enter the GREEN SELECT button
operating settings.
Press to activate CHARGE-PAK indicator on the
readiness display (active only when Trainer is in
simulated OFF status). To clear, press the button
again.
Press to enter the RED SELECT button
operating settings.
Press the RIGHT ARROW button to advance
to the next operating setting.
Press the UP ARROW button to select the
desired option.
Feature not available
LIFEPAK® CR–T AED TRAINER
Quick Start Reference Card
Button
Function
Button
Function
Press to change SHOCK ADVISED to NO SHOCK
ADVISED. Function is active only during simulated
analysis.
Press once to activate the ATTENTION
indicator in the readiness display. To clear,
press the button again.
Press to advance the training electrodes to ON or
OFF.
Press any time to suspend device
operation. Press again to resume operation
at point of interruption.
Press to advance MOTION DETECTED to ON or OFF.
This feature is active during simulated analysis only.
Press to change the speaker volume. The
volume level scrolls up, and returns to
lowest level after the highest is reached.
Press to activate WRENCH indicator on the readiness
display (active only when Trainer is in simulated OFF
status). To clear, press the button again.
Press to enter the GREEN SELECT button
operating settings.
Press to activate CHARGE-PAK indicator on the
readiness display (active only when Trainer is in
simulated OFF status). To clear, press the button
again.
Press to enter the RED SELECT button
operating settings.
Feature not available.
Press the RIGHT ARROW button to advance
to the next operating setting.
Press the UP ARROW button to select the
desired option.
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
C
37
Appendixes
APPENDIX C
DECLARATION OF CONFORMITY
Declaration of Conformity
Appendixes
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
39
INDEX
A
Attention Button 7, 11
Attention Indicator 3
Automatic Defibrillator operating setting 17
Automatic/Semiautomatic Shock 17, 20
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
Index
B
Back View of Trainer 4
Battery
Compartment for 4
Replacement of 24
Bottom View of Trainer 3
Buttons
Attention 7, 11
CHARGE-PAK 7, 11
Electrode Pads 6, 7
Green Select 7, 12
Lid Release/ON-OFF 4
Motion 7, 11
No Shock Advised 7, 11
Pause 7, 11
Red Select 7, 12
Remote Control 7, 10–12
Right Arrow 7, 12
Service 7, 11
Shock 6
Up Arrow 7, 12
Volume Control 7, 12
Wrench 7, 11
C
Carrying Handle 3
Changing
Custom Shock Protocols 19
Operating Settings 18
CHARGE-PAK
Button location 7
Button operation 11
Indicator location 3
Trainer description 4
Cleaning the AED Trainer 26
Clearing the CHARGE-PAK Indicator 14
Conducting a Training Session 13
Connecting the Training Electrode Packet 12
Controls, Indicators, and Labels 3–4
CPR Time 17
D
Default Operating Settings 16–17
Default Settings, resetting 22
E
Electrode
Connector location 6
Electrode (QUIK-PAK) Packet
Anchor Pin location 5
Connecting to AED Trainer 12
Release Handle location 5
Removing from manikin following a session 14
41
Index
Electrode Pads
Button location 7
Button operation 10
Indicators description 6
F
Features inside the AED Trainer 5–6
G
General Operating Settings
Automatic/Semiautomatic Shock 17, 20
CPR Time 17
Pulse Check 17, 20
Pulse Prompts 16, 20
Shock Protocol 16
Stack Shocks 17, 20
Start Prompt 16, 20
Green Select Button
Location 7
Operation 12
H
Handle location 3
Handle, carrying 3
I
Inside Features 5, 6
Installing and Replacing Batteries 8, 24
Installing and Replacing Remote Control Batteries 8
L
Language Option 17, 21
LED
Display location 4
Display operation 18–21
Troubleshooting 24
Lid 3
Lid Release/ON-OFF Button 4
LIFEPAK CR–T AED Trainer
Accessories for 27
Back View of 4
Bottom View of 3
Cleaning the 26
Controls, Indicators, and Labels 3–4
Features inside of 5–6
Installing/Replacing Batteries in 8, 24
Operating/Default Settings of 16–17
Remote Control/Remote Control Cable features
7
Specifications for 27
Storing the 2, 14
Troubleshooting 24–25
Warranty 26
42
M
Master Power Switch location 4
Motion Button
Location 7
Operation 11
N
No Shock Advised Button
Location 7
Operation 11
O
OK Indicator location 3
Operating Settings Options 18
Operating Settings/Defaults
Automatic/Semiautomatic Shock 17, 20
CPR Time 17
Language option 17
Pulse Check 17, 20
Pulse Prompts 16, 20
Shock Protocol 16
Stack Shocks 17, 20
Start Prompt 16, 20
Outside Controls, Indicators, and Labels 3
P
Pause Button
Location 7
Operation 11
Power Switch, Master 4
Preparing for a Training Session 12
Product Recycling 26
Pulse Check 17, 20
Pulse Prompts 16, 20
Q
Quick Reference Card 35
QUIK-PAK Training Electrodes location 5
R
Readiness Display location 3
Red Select Button
Location 7
Operation 12
Remote Control
Buttons functions 10–12
Buttons locations 7
Cable connection description 7
Cable connection location 4
Cable connection operation 12
Communication description 10
Functions 10–12
Operation 10
Signal Sensor location 4
Specifications 28
Storage compartment location 4
Troubleshooting 25
LIFEPAK CR–T Trainer Operating Instructions
Index
Replacing Batteries 24
Resetting Default Settings 22
Right Arrow Button
Location 7
Operation 12
S
Semiautomatic Defibrillator operating setting 17
Service Button
Location 7
Operation 11
Setting
CPR Time 21
General Operation 20
Language Option 21
Shock protocol 18
Setup Configuration and Operating Settings 16–17
Setup Options Troubleshooting 25
Shock
Button cover placement 13
Button location 6
Custom protocols 19
Fixed protocols 18
Protocol Operation 16, 18–19
Side View of Trainer 4
Speaker location 6
Specifications 27
Stack Shocks 17, 20
Start Prompt 16, 20
Storing the Trainer following Training Session 14
Using the Remote Control 10
Using the Remote Control Cable 12
V
Voice Prompts and Tones
Description 31
Troubleshooting 24
Volume Control Button
Location 7
Operation 12
W
Warranty 26
Wrench
Button 11
Indicator 3
Index
T
Top View of Trainer 3
Training Electrode Placement 14
Training Electrodes (QUIK-PAK)
Connecting for Training Session 13
Connector location 6
Pads location (packet closed) 5
Pads location (packet open) 6
Placing (electrodes) during Training Session 13
Removing (electrodes) following Training
Session 14
Troubleshooting 25
Training Sessions
Conducting a 13
Following a 14
Preparing for 12
Training Shock Button location 6
Turning On the Trainer 13
U
Unpacking and Inspecting the Trainer 2
Up Arrow Button
Location 7
Operation 12
Use By Date
Location 5
Operation 5
LIFEPAK CR–T Trainer Operating Instructions
©2002-2007 Medtronic, Inc.
43
Medtronic, Inc.
11811 Willows Road NE
Redmond, WA 98052-2003 USA
Telephone: 425.867.4000
Toll Free (USA only): 800.442.1142
Fax: 425.867.4121
Internet: www.medtronic-ers.com
Medtronic Europe S.A.
Rte. du Molliau 31
Case postale 84
1131 Tolochenaz
Switzerland
Telephone: 41.21.802.7000
Fax: 41.21.802.7900
MIN 3201838-003 / CAT. 26500-001156