CMA Dishmachines CMA-180 Specifications

MODEL CMA-180
Installation & Operation
Rev 2.03
CMA DISHMACHINES
12700 KNOTT AVENUE
GARDEN GROVE, CALIFORNIA 92841
800-854-6417
FAX 714-895-2141
www.cmadishmachines.com
Table of Contents
CMA-180
1.
SPECIFICATIONS................................................................................................. 2
1.1
CMA-180/CMA-180T.................................................................................................................... 2
1.1.
CMA-180/CMA-180T.................................................................................................................... 3
2.
GETTING STARTED ............................................................................................ 4
2.1.
Introduction to CMA-180............................................................................................................... 4
2.2.
Receiving and Installation .............................................................................................................. 5
2.2.1.
2.2.2.
2.2.3.
2.2.4.
2.2.5.
2.2.6.
2.2.7.
2.2.8.
Electrical ................................................................................................................................ 5
Plumbing................................................................................................................................. 5
Nova Detergent and Rinse Dispenser..................................................................................... 5
Exhaust Fan Control .............................................................................................................. 8
Water Tempering Kit .............................................................................................................. 9
Installation Checklist ............................................................................................................ 10
Machine Start-Up Procedures .............................................................................................. 11
Electrical Requirements........................................................................................................ 12
3.
WIRING OPTIONS ............................................................................................. 13
4.
QUICK SERVICE GUIDE .................................................................................. 14
5.
INITIAL PARTS KIT P/N 1100.17..................................................................... 15
6.
AUTO-FILL SOLID STATE TIMER ................................................................ 16
7.
WIRE DIAGRAM ................................................................................................ 17
8.
WIRE DIAGRAM FOR CMA-180 BOOSTER ONLY .................................... 18
www.cmadishmachines.com
1. Specifications
1.1
Metric
Equivalent
CMA-180/CMA-180T
WATER CONSUMPTION
PER RACK
.96 GAL.
(3.6 L)
PER HOUR
52 GAL.
(197 L)
WASH TIME-SEC
49
49
RINSE TIME-SEC
12
12
61 MIN.
61 MIN.
60
60
WASH TANK CAPACITY
8 GAL.
(30.3 L)
PUMP CAPACITY
68 GPM
(257 LPM)
OPERATING CYCLE
TOTAL CYCLE
OPERATING CAPACITY
RACKS PER HOUR (NSF rated)
WATER REQUIREMENTS
WITHOUT BOOSTER HEATER
180°F
(82°C)
WITH BOOSTER HEATER
140°F
(60°C)
WATER INLET
¾”
1.9cm
DRAIN CONNECTION
2”
5.1cm
20 PSI
1.41 kg/cm2
RINSE PRESSURE SET
CYCLE TEMPERATURES
WASH-°F
155°F-160°F
(68°C/71°C)
RINSE-°F
180°F-195°F
(82°C/90°C)
DEPTH
25”
(63.5cm)
WIDTH
25 ½”
(65cm)
HEIGHT
59-60
(150-152cm)
STANDARD TABLE HEIGHT
34”
MAX CLEARANCE FOR DISHES
17 ½”
DIMENSIONS
DRAIN CONNECTION (OFF FLOOR)
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
(86.3cm)
11 ½“ – 12 ½“ (29-32cm)
Page 2
1.1. CMA-180/CMA-180T
VOLTS
PHASE
AMPS
208
1
28/35
240
1
30/38
208
3
20/24
240
3
21/26
ELECTRICAL RATING
208
1
71/78
WITH BOOSTER
240
1
80/88
208
3
45/49
240
3
50/55
ELECTRICAL RATING
WITHOUT BOOSTER
SHIPPING WEIGHT
WITHOUT BOOSTER
WITH BOOSTER
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
332#
375#
Page 3
2. Getting Started
2.1.
Introduction to CMA-180
The CMA-180 is a hot water sanitizing, single rack, door-type dishmachine. It is a stand-alone
machine featuring a self-contained booster heater (optional). The only external connections
necessary are power supply, water supply, drainpipe, and chemical dispensers. The machine
utilizes recirculated wash water and fresh water final rinse. The CMA-180 can be converted both
as a straight through and corner with a door handle kit.
Operation of the CMA-180 is automatic. When the door is opened and then closed, the wash
cycle begins automatically. To initially fill the machine daily, open the hand operated fill valve on
the top of the machine. The machine is full when water begins to flow into the scrap trap. The
wash tank heater will maintain the wash water temperature at 155°F. The booster heater will
produce a minimum of 180°F final rinse water each cycle.
This manual is structured to provide a complete reference guide to the CMA-180. It is presented
in a manner that all users will be able to comprehend and use as an effective tool in supporting
the operation and maintenance of the dishmachine. The first section explains how the machine is
packaged and what to look for when receiving the machine.
Instructions are provided in the manual explaining how to unpack the machine and then install
and set up the machine for use. Requirements are given for plumbing, wiring, and space
considerations. These attributes of the machine are always taken into consideration by our welltrained sales representatives prior to the order being placed. In the manual, additional installation
guidance is given to ensure the machine can run at optimum conditions.
The Operation Section of the manual may be used for instruction and procedures when required.
We make this portion of the manual easy to understand so that all levels of operators may be
able to read and comprehend the operation of the machine. The function of the machine itself is
mostly automatic and takes little training to put into full operation. The Operation Section also
includes diagnostic considerations for the machine when problems occur.
We are committed to providing the best machines and customer service in the food industry and
your feedback is welcome.
CMA warranties the workmanship of the machine.
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 4
2.2.
Receiving and Installation
Step 1: Remove packaging material.
Step 2: Remove service manual and machine legs from inside the wash tank.
Step 3: Install legs into dishmachine leg lockets and adjust the feet. Set the
machine in place. Level the machine side – to – side and front – to –
back.
Step 4: It is recommended that a distance of at least eight inches (8”) be
between the table scrap sink and the dishmachine.
2.2.1. Electrical *
The control panel provides a 1” conduit connection point on the rear of the panel.
Refer to Section 3 for wiring options.
This machine is equipped to handle both single and three phase applications.
See Section 1: Specifications 1.1 for the proper electrical ratings.
2.2.2. Plumbing *
Minimum 140°F / Minimum 180°F (if machine ordered without booster heater,
water supply ¾” – minimum 20 psi, 6 gpm flow rate and 60 gph recovery rate.
Plumbing connection located on the top of the machine.
The drain is a two inch (2”) pipe sleeve attached by “No-Hub” plumbing
connection at the bottom of the scrap trap. Account’s drain should be no higher
than 11” to allow the machine to drain properly.
2.2.3. Nova Detergent and Rinse Dispenser
The NOVA Detergent and Rinse Dispenser has its own reference manual.
Familiarize yourself with the dispenser’s reference manual before proceeding with
installation.
1. The NOVA dispenser is pre-wired with a multi-conductor electrical cable that is to
be run through a conduit to the power block inside the control panel drawer. Use
a ½” watertight conduit meeting all local and national codes. A conduit fitting is
present on the bottom of the dispenser where the power cable exits. Use the
same conduit fitting in the back of the control box. The probe is also pre-wired
(see two violet wires routed from the control box to the probe location inside the
wash tank heater thermostat enclosure).
i.
Run an appropriate length of ½” conduit from your dispenser to the control
box where it will be secured. The conduit needs to be of sufficient length and
*
Electrical and pluming connections must be made by qualified person who comply with all
available Federal, State, and Local Health, Electrical, Plumbing and Safety codes
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 5
flexibility to permit the machine to be moved for cleaning without having to
disconnect any wiring.
ii.
Run your dispenser wires through the conduit to the control box.
iii.
Run your probe wires to the control box.
iv.
With the machine’s power “OFF”, connect your detergent and rinse dispenser
wires to the red and blue terminals of the power block supplied inside the control
box. The table that follows lists the function of each conductor of the multiconductor electrical cable.
Wire Colors
Circuit Voltage
Function
Gray/Violet
200 VAC-249 VAC 50/60 Hz
Main AC Power
Brown
200 VAC-249 VAC 50/60 Hz
Main AC Power
Black
No Connection. Insulate this wire!
This wire is LIVE!
Yellow
24 VAC-240 VAC 50/60 Hz
Detergent Signal
White/Yellow
24 VAC-240 VAC 50/60 Hz
Detergent Signal
Violet
24 VAC-240 VAC 50/60 Hz
Rinse Signal
White/Violet
24 VAC-240 VAC 50/60 Hz
Rinse Signal
The individual conductors need to be connected as shown on the wire
diagram below. Probe wires are to be striped, crimped on barrel male and
female connectors provided, and connected to the pre-wired violet wires in
the control box.
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 6
2. Remove the plug from the mixing chamber located by the vacuum breaker on the
back of machine; and install the rinse injection fitting (supplied with your
dispenser).
3. A 7/8” detergent injection hole is provided in the back of the wash tank. Remove
the S.S. plug and install the detergent fitting (supplied with your dispenser).
4. A 7/8” chemical probe hole is provided in the front of the wash tank heater just
below hi limit switch. Insert the probe into the hole from inside the wash tank and
secure it with the probe retaining nut provided. Connect ring connectors to the
probe with nuts and star washers provided.
5. The final step of installing the CMA supplied Detergent and Rinse Dispenser is
programming it to your specific application. The reference manual supplied with
the dispenser shows you how to program it.
Keep in mind while reading the reference manual that the CMA-180 operates
in “probe” mode. (This mode is selected by setting a value of “1” in screen
21).
Screen 22 must be set to “1” (Door).
There are four user functions with this dispenser. Their operation is described in the
reference manual.
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 7
2.2.4. Exhaust Fan Control
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 8
2.2.5. Water Tempering Kit
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 9
2.2.6. Installation Checklist
Dishmachine checked for concealed damage.
Hot water supply is 140° (60°C)
Incoming water supply line is ¾”.
Incoming water supply is 6 gpm minimum capable at 20 psi flow pressure.
Machine circuit breaker is properly sized.
Service voltage and phase type are correct to machine data plate.
High leg of voltage is connected to L2 (three-phase).
Dishmachine is properly ventilated.
Floor drain plumbing is installed with air gap.
Dishmachine is properly grounded.
Dishmachine is properly leveled.
Dishrack guides are adjusted to level of dishtable.
Machine circuit breaker is labeled D/W
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 10
2.2.7. Machine Start-Up Procedures
1. Open doors and install the overflow & scrap trap on the right side of the machine.
2. Place the scrap baskets over the wash tanks.
3. Secure the wash & rinse arms and check the free-spin.
4. Open the control cover and select ‘normal” toggle switch position.
5. Adjust the rinse pressure to 20 psi flow pressure using the regulator and the gauge.
a. Turn the power switch to the “Off” position.
b. Close doors and open the hand-operated fill valve until the water overflows into
the scrap trap.
c.
Turn the power switch to “on” position.
d. While holding “flush” toggle switch, to activate the water solenoid, adjust the
pressure regulator until the gauge reads 20 psi.
6. Connect the detergent and rinse dispenser to the power block supplied & labeled inside
the control box (208-220) volt).
7. Remove the plug from the mixing chamber and install the rinse injection fitting.
8. A 7/8” chemical probe hole is provided in the wash tank.
9. A 7/8” detergent fitting hole is provided in the wash tank.
10. Check the machine operating temperatures. Adjust if necessary.
a. After the machine has warmed up for five to ten minutes (5 – 10 min.), observe
the wash and rinse temperatures. The wash temperature must be 155°F
minimum. The rinse temperature must be 180°F minimum. If necessary, adjust
the temperatures by removing the panel in front of the respective heater and
turning the adjustment post clockwise to increase.
NOTE: Rinse water temperature must be observed during the rinse cycle.
11. Check all water and drain fittings for leaks.
12. Install the wall chart and instruct the machine operator on the proper cleaning and
operation of the CMA-180.
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 11
2.2.8. Electrical Requirements
The CMA-180 comes standard factory, wired for 3-phase operation. Check the electrical data
plate to confirm this. If the account requires 1 phase, refer to “Electrical Requirements”, Section
1-A, for proper wiring instruction for conversion. Also check the wiring diagram to properly wire
the terminal power block, tank heater, and booster heater for 1 phase (or 1B diagram below).
SINGLE PHASE POWER
NOTE: 80 amp service is required when CMA-180 is wired for single-phase with the booster
heater. See “Electrical Requirements” section for DUAL 1-phase power supply. Circuit breaker
requirement (1) 50 amp & 30 amp.
Figure 1-B
Single Phase
Single Phase
Rinse Booster Heater
Wash Tank Heater
1. Install booster heater
wires and bus bars as
1. Install wash heater bus
bars as shown above.
2. Connect wire #59 to
heater L1.
2. Connect wire #15 to
heater L1.
3. Connect wire #57 to
heater L2.
3. Connect wire #17 to
heater L2.
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 12
3. Wiring Options
3-Phase and 1 Phase
Wiring Options
Single-Source
220V 3-Phase
(20 amp/12 g*)
Single-Source
220V 3-Phase
(50 amp/8 g*)
Single-Source
220V 1-Phase
(80 amp/4 g*)
(without Booster)
Two-Source
220V 1-Phase
(50 amp/8 g*)
(30 amp/10 g*)
Single-Source
220V 1-Phase
(30 amp/10 G*)
(without booster)
*g=gauge
DISPENSER HOOK-UP
1. The power signal is 208/230 volts. The power block is labeled inside the control box.
Conduit holes for both detergent & rinse are supplied on the control box.
2. A threaded (1/8”) injection point is provided on the final rinse Teflon mixing chamber
located off the back of the machine.
3. A (7/8”) hole is provided in the tank for a probe access. It is located on the front side of
the wash tank inside the heater cover.
MAIN POWER CONNECTION
Please refer to the machine data plate or choose one of the five (5) power connections illustrated
above (1A). Electrical requirements are shown for machines with or without booster heater, three
or single phase.
WARNING: Insure that the machine is properly grounded and complies to all local and national
codes. Injury or death may occur from shock, if the machine is not properly grounded.
Install power supply wires, L1, L2 and L3 (3-Phase) to the appropriate terminals marked L1, L2,
and L3 on the power block. (If applicable, the high or “wild” leg must be connected to the L2
Terminal.)
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 13
4. Quick service guide
MODEL: CMA 180 HIGH TEMP
TECHNICAL ISSUE
Door magnetic reed switch problem
Door mechanical switch problem
Pump motor not running
Pump motor runs continuous
CAUSE
Faulty magnetic reed switch
SOLUTION
Check wire connections inside control box
Switch alignment issue
Contact factory for new retrofit, corner P/N
00566.10 straight P/N 00566.20
Align switch
Switch button broke
Replace switch, P/N00562.00
Delimer switch is in OFF position
Flip to NORMAL position
Loose wire connections
Check and crimp connectors
Faulty # 3 micro switch in cam timer
Replace micro switch, P/N 00411.00
Faulty contactor
Replace contactor, P/N 00404.85
Faulty wash pump motor
Replace wash pump motor, P/N 00201.00
Faulty # 3 micro switch in cam timer
Replace micro switch, P/N 00411.00
Delimer switch is in DELIME position
Flip to NORMAL position
Faulty contactor
Replace contactor, P/N 00404.85
Booster heater thermostat not properly set
Adjust thermostat
Incoming main water temperature below 140 F Raise water temperature to 140 F
Final rinse water below 180 degree F
Wash tank heater is not operational
Tripped or faulty high limit switch
Reset or replace high limit switch, P/N 17523.51
Faulty contactor
Replace contactor, P/N 13003.17
Faulty booster heater element
Replace heating element, P/N 13417.67
Scaled heating element
Thermostat is not properly adjusted
De- scale heating element
Adjust thermostat
Loose lead connection
Tripped or faulty high limit switch
Check connectors and secure
Reset or replace high limit switch, P/N 17523.51
Faulty float switch
Replace float switch, P/N 13463.00
Faulty contactor
Replace contactor, P/N13003.50
Faulty heating element
Replace heating element, P/N 13417.65
Water regulator not adjusted properly
Adjust regulator to 18-20 PSI
Low water pressure at the final rinse
Clogged final rinse spray jets
Missing final rinse spray end cap
Clean jets
Replace end cap, P/N 00308.17
Increase pressure
Water solenoid leaks
Low incoming water pressure from building
Scaled or dirty solenoid valve
Clean valve
Faulty solenoid valve diaphragm
Thermostat not properly set
Replace diaphragm, P/N 00706.00
Adjust thermostat
Scaled heating element
Clean scale, delime machine
Faulty temperature gauge
Position or proper operation of door switch
Replace gauge, P/N 03202.00
Adjust or replace door switch, P/N 00557.55
Delimer switch is on OFF position
Faulty 1st micro switch in cam timer
Flip to NORMAL position
Replace micro switch, P/N 00411.00
Check cam timer motor
Replace timer if needed, P/N 00409.17
Check ice cube relay
Replace if faulty, P/N 00631.05
Replace contactor, P/N 00404.85
Wash water temperature too low/high
Machine does not operate when the door is
closed
Faulty wash pump contactor
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 14
5. INITIAL PARTS KIT P/N 1100.17
P/N
00121.18
00200.10
00206.00
00302.19
00304.17
00304.19
00308.17
00308.50
00363.00
00404.85
00405.00
00411.00
00475.00
00501.17
00562.00
00602.00
00631.05
00706.00
00735.00
00738.15
03202.00
03202.00
03408.55
13003.17
13003.50
13304.55
13415.00
13417.47
13417.65
13417.67
13417.85
13463.10
13605.00
00421.90
00421.78
17523.51
DESCRIPTION
CMA-180 Drain Stopper O Ring
Pump Assy 110/220V 60 Hz (Open)
Pump Seal Kit
CMA-180 Buna Gasket (#302.17)
CMA-180 Wash Spray Arm
CMA-180 Rinse Arm W/Bearing
CMA-180 Rinse Arm SS End Plug
Spray Arm End Plug SS
Spray Base Lock Pin
Contactor 208.240V 20AMP
Start/Fill Switch Toggle
Micro Switch
Toggle Switch DPDT 15 AMP/Delimer
Timer Motor Assy 60 Sec. 220V/60Hz
Roller Door Switch
Door Spring
Ice Cube Relay 220V
¾ Water Solenoid Repair Kit JE
¾ Vac Breaker Rep Kit Watts
¾ Solenoid Coil JE 220V
Thermometer CMA-180 “Wash”
Thermometer CMA-180 “Rinse”
Counter (Face Mount Sm) 220/50
Contactor 60 AMP 3 Pole
Contactor 30 AMP
SS Final Rinse Spray Jet – HT
EGO Thermostat Retrofit Kit Rinse
CMA-180 Booster Heater Gasket
Immersion Heater 5 Kw 3hp/1ph
Immersion Heater 12 Kw 3PH/1PH
Thermostat Heater CMA-44/CMA-180 Wash
Liquid Level Switch SS – CMA-44
Pressure Gauge
CMA-180 Power Switch
CMA-180 Illuminated Plug
Hi Limit Switch 250 deg
NO. REQ’D
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
NOTE: CMA recommend that this Model CMA-180 initial parts kit be
kept on hand, as a back up supply, in the event your machine should
require emergency service. All the parts included in this kit are
unique to the CMA-180 dishmachine, and are essential to the “quality”
operation and customer service to the CMA-180 unit.
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 15
6. Auto-Fill Solid State Timer
Pre-selected delay period can be adjusted by
turning securely small flat screwdriver. Since
the range of this solid state timer is from 6
seconds to 240 seconds, you should adjust
delay by small increment.
Removal of input power will reset the control.
AUTO-FILL
SWITCH
L2
L1
WASH PUMP
CONTACTOR
6
T2
WATER
SOLENOID
VALVE
T1
1
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
2
3
Page 16
7. Wire Diagram
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 17
DETERGENT
{
L1
L3
GND
L3
L2
L1
L2
L1
L3
L2
L1
HEATER
CONTACTOR
RINSE SIGNAL {
BOOSTER
HEATER
CONTACTOR
L2
GROUND
WASH PUMP
CONTACTOR
8. Wire Diagram for CMA-180 Booster Only
T2
T1
T3
T2
T1
T3
T2
T1
PUMP
MOTOR
HI LIMIT
SWITCH
5kW
ADJ.
THERMOSTAT
WASH TANK
HEATER
12kW
BOOSTER
HEATER
MODEL CMA-180 INSTALLATION & OPERATION Rev. 2.03
Page 18