Yamaha GP800Y WaveRunner GP Service manual

WaveRunner
GP800R
SERVICE MANUAL
*LIT186160226*
LIT-18616-02-26
F0W-28197-1A-11
E
NOTICE
This manual has been prepared by Yamaha primarily for use by Yamaha dealers and their
trained mechanics when performing maintenance procedures and repairs to Yamaha equipment. It has been written to suit the needs of persons who have a basic understanding of the
mechanical and electrical concepts and procedures inherent in the work, for without such
knowledge attempted repairs or service to the equipment could render it unsafe or unfit for
use.
Because Yamaha has a policy of continuously improving its products, models may differ in
detail from the descriptions and illustrations given in this publication. Use only the latest edition of this manual. Authorized Yamaha dealers are notified periodically of modifications and
significant changes in specifications and procedures, and these are incorporated in successive editions of this manual.
A10001-0*
WaveRunner GP800R
SERVICE MANUAL
©2000 by Yamaha Motor Corporation, USA
1st Edition, November 2000
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, USA
is expressly prohibited.
Printed in USA
LIT-18616-02-26
E
HOW TO USE THIS MANUAL
MANUAL FORMAT
All of the procedures in this manual are organized in a sequential, step-by-step format. The
information has been compiled to provide the mechanic with an easy to read, handy reference that contains comprehensive explanations of all disassembly, repair, assembly, and
inspection operations.
In this revised format, the condition of a faulty component will precede an arrow symbol and
the course of action required will follow the symbol, e.g.,
● Bearings
Pitting/scratches → Replace.
To assist you in finding your way through this manual, the section title and major heading is
given at the top of every page.
ILLUSTRATIONS
The illustrations within this service manual represent all of the designated models.
CROSS REFERENCES
The cross references have been kept to a minimum. Cross references will direct you to the
appropriate section or chapter.
E
IMPORTANT INFORMATION
In this Service Manual particularly important information is distinguished in the following
ways.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
WARNING
Failure to follow WARNING instructions could result in severe injury or death to the machine
operator, a bystander, or a person inspecting or repairing the watercraft.
CAUTION:
A CAUTION indicates special precautions that must be taken to avoid damage to the watercraft.
NOTE:
A NOTE provides key information to make procedures easier or clearer.
IMPORTANT:
This part has been subjected to change of specification during production.
E
HOW TO USE THIS MANUAL
1 To help identify parts and clarify procedure steps, there are exploded diagrams at the start
of each removal and disassembly section.
2 Numbers are given in the order of the jobs in the exploded diagram.
3 Symbols indicate parts to be lubricated or replaced (see “SYMBOLS”).
4 A job instruction chart accompanies the exploded diagram, providing the order of jobs,
names of parts, notes in jobs, etc.
5 Dimension figures and the number of parts, are provided for fasteners that require a tightening torque.
Example:
Bolt or screw size
10 × 25 mm
: M10 (D) × 25 mm (L)
D
L
6 Jobs requiring more information (such as special tools and technical data) are described
sequentially.
E
1
A50001-1-4
2
GEN
INFO
SYMBOLS
Symbols 1 to 9 are designed as thumbtabs to indicate the content of a chapter.
SPEC
3
1
2
3
4
5
6
7
8
9
4
INSP
ADJ
FUEL
5
6
JET
PUMP
POWR
7
General Information
Specifications
Periodic Inspection and Adjustment
Fuel System
Power Unit
Jet Pump Unit
Electrical System
Hull and Hood
Trouble analysis
8
–
ELEC
9
+
HULL
HOOD
Symbols 0 to E indicate specific data:
0
0
A
B
C
D
E
TRBL
ANLS
A
B
C
D
Symbol F to H in an exploded diagram
indicate the grade of lubricant and the location of lubrication point:
T.
R.
E
F
E
G
Special tool
Specified liquid
Specified engine speed
Specified torque
Specified measurement
Specified electrical value
[Resistance (Ω), Voltage (V), Electric current
(A)]
F Apply YAMALUBE 2-W oil or TC-W3 cirtified
outboard oil
G Apply water resistant grease
(Yamaha grease A, Yamaha marine grease)
H Apply molybdenum disulfide grease
H
M
A
I
J
Symbols I to N in an exploded diagram
indicate the grade of the sealing or locking
agent, and the location of the application
point:
LT
LT
271
242
I Apply Gasket Maker®
J Apply Yamabond #4
(Yamaha bond number 4)
K Apply LOCTITE® No. 271 (Red LOCTITE)
L Apply LOCTITE® No. 242 (Blue LOCTITE)
M Apply LOCTITE® No. 572
N Apply silicone sealant
SS
LT
NOTE:
In this manual, the above symbols may not
be used in every case.
4
GM
K
L
M
N
LT
572
E
A30000-0
INDEX
GENERAL INFORMATION
SPECIFICATIONS
PERIODIC INSPECTION AND
ADJUSTMENT
FUEL SYSTEM
POWER UNIT
JET PUMP UNIT
GEN
INFO
SPEC
INSP
ADJ
FUEL
POWR
JET
PUMP
–
ELECTRICAL SYSTEM
HULL AND HOOD
TROUBLE ANALYSIS
+
ELEC
HULL
HOOD
TRBL
ANLS
1
2
3
4
5
6
7
8
9
GEN
INFO
E
CHAPTER 1
GENERAL INFORMATION
IDENTIFICATION NUMBERS ......................................................................... 1-1
PRIMARY l.D. NUMBER........................................................................... 1-1
ENGINE SERIAL NUMBER ...................................................................... 1-1
JET PUMP UNIT SERIAL NUMBER ........................................................ 1-1
HULL IDENTIFICATION NUMBER (H.l.N.).............................................. 1-1
SAFETY WHILE WORKING ...................................................................... 1-2
FIRE PREVENTION ................................................................................... 1-2
VENTILATION........................................................................................... 1-2
SELF-PROTECTION.................................................................................. 1-2
OILS, GREASES AND SEALING FLUIDS................................................ 1-2
GOOD WORKING PRACTICES ................................................................ 1-3
DISASSEMBLY AND ASSEMBLY ........................................................... 1-4
SPECIAL TOOLS ............................................................................................. 1-5
MEASURING ............................................................................................ 1-5
REMOVAL AND INSTALLATION ............................................................ 1-6
1
2
3
4
5
6
7
8
9
GEN
INFO
IDENTIFICATION NUMBERS
E
A60700-0*
IDENTIFICATION NUMBERS
PRIMARY l.D. NUMBER
The primary l.D. number is stamped on a
label attached to the inside of the engine
compartment.
Starting primary l.D. number:
F0W: 800101–
ENGINE SERIAL NUMBER
The engine serial number is stamped on a
label attached to the cylinder head.
Starting serial number:
68A: 000101–
JET PUMP UNIT SERIAL NUMBER
The jet pump unit serial number is stamped
on a label attached to the intermediate
housing.
Starting serial number:
68A: 800101–
HULL IDENTIFICATION NUMBER
(H.l.N.)
The H.l.N. is stamped on a plate attached to
the aft deck.
1-1
GEN
INFO
SAFETY WHILE WORKING
E
SAFETY WHILE WORKING
The procedures given in this manual are
those recommended by Yamaha to be followed by Yamaha dealers and their
mechanics.
FIRE PREVENTION
Gasoline (petrol) is highly flammable.
Gasoline vapor is explosive if ignited.
Do not smoke while handling gasoline
(petrol) and keep it away from heat, sparks,
and open flames.
VENTILATION
Gasoline vapor is heavier than air and is
deadly if inhaled in large quantities. Engine
exhaust gases are harmful to breathe.
When test-running an engine indoors,
maintain good ventilation.
SELF-PROTECTION
Protect your eyes with suitable safety spectacles or safety goggles when grinding or
doing any operation which may cause particles to fly off.
Protect hands and feet by wearing safety
gloves or protective shoes if appropriate to
the work you are doing.
OILS, GREASES AND SEALING
FLUIDS
Use only genuine Yamaha oils, greases,
and sealing fluids or those recommended
by Yamaha.
1-2
GEN
INFO
SAFETY WHILE WORKING
E
Under normal conditions of use there
should be no hazards from the use of the
lubricants mentioned in this manual, but
safety is all-important, and by adopting
good safety practises any risk is minimized.
A summary of the most important precautions is as follows:
1. While working, maintain good standards of personal and industrial
hygiene.
2. Clothing which has become contaminated with lubricants should be
changed as soon as practicable and
laundered before further use.
3. Avoid skin contact with lubricants (e.g.,
do not place a soiled rag in your
pocket).
4. Hands and any other part of the body
which have been in contact with lubricants or lubricant-contaminated clothing should be thoroughly washed with
hot water and soap as soon as practicable.
5. To protect the skin, the application of a
suitable barrier cream to the hands
before working is recommended.
6. A supply of clean lint-free cloths should
be available for wiping purposes.
GOOD WORKING PRACTICES
1. The right tools
Use the recommended special tools to
protect parts from damage. Use the
right tool in the right manner – do not
improvise.
2. Tightening torque
Follow the tightening torque instructions. When tightening bolts, nuts and
screws, tighten the larger sizes first and
tighten inner-positioned fixings before
outer-positioned ones.
1-3
GEN
INFO
SAFETY WHILE WORKING
E
3. Non-reusable items
Always use new gaskets, packings, Orings, oil seals, split-pins, circlips, etc.,
on reassembly.
DISASSEMBLY AND ASSEMBLY
1. Clean parts with compressed air when
disassembling.
2. Oil the contact surfaces of moving parts
during assembly.
3. After assembly, check that moving parts
operate normally.
4. Install bearings with the manufacturer’s
markings on the side exposed to view
and liberally oil the bearings.
CAUTION:
Do not spin bearings with compressed air
because this will damage their surfaces.
5. When installing oil seals, apply a light
coat of water-resistant grease to the
outside diameter.
1-4
GEN
INFO
SPECIAL TOOLS
E
SPECIAL TOOLS
Using the correct special tools recommended by Yamaha, will aid the work and
enable accurate assembly and tune-up.
Improvisations and using improper tools
can damage the equipment.
1 YU-8036-A
NOTE:
● For U.S.A. and Canada, use part numbers
starting with “J-”, “YB-”, “YM-”, “YU-” or
“YW-”.
● For other countries, use part numbers
starting with “90890-”.
90890-06760
MEASURING
2 YU-03097
1 Engine tachometer
P/N. YU-8036-A
90890-06760
2 Dial gauge and stand
P/N. YU-03097, YU-01256
90890-01252
3 Pocket tester
P/N. YU-03112
90890-03112
4 Cylinder gauge set
P/N. YU-03017
90890-06759
5 Compression gauge
P/N. YU-33223
90890-03160
6 Digital tester
P/N. J-39299
90890-06752
7 Peak voltage adapter
P/N. YU-39991
90890-03169
8 Peak voltage test harness
P/N. YW-06779
90890-06779
9 Spark gap tester
P/N. YM-34487
90890-06754
90890-01252
YU-01256
3 YU-03112
90890-03112
5 YU-33223
4
90890-03160
6 J-39299
7 YU-39991
90890-03169
9 YM-34487
YU-03017
90890-06759
90890-06752
8
YW-06779
90890-06779
90890-06754
1-5
GEN
INFO
1
SPECIAL TOOLS
2
YW-06551
E
REMOVAL AND INSTALLATION
YW-06550 90890-06550
1 Coupler wrench
P/N. YW-06551
90890-06551
2 Flywheel holder
P/N. YW-06550
90890-06550
3 Flywheel puller
P/N. YB-06117
90890-06521
4 Drive shaft holder (impeller)
P/N. YB-06151
90890-06519
5 Slide hammer set (jet pump bearing)
P/N. YB-06096
6 Stopper guide plate (jet pump bearing)
P/N. 90890-06501
7 Bearing puller (jet pump bearing)
P/N. 90890-06535
8 Bearing puller claw 1 (jet pump bearing)
P/N. 90890-06536
9 Stopper guide stand (jet pump bearing)
P/N. 90890-06538
0 Drive rod L3 (jet pump bearing)
P/N. 90890-06652
A Needle bearing attachment
(jet pump bearing and oil seal)
P/N. YB-06112, YB-06196
90890-06614, 90890-06653
B Ball bearing attachment
(jet pump oil seal)
P/N. YB-06156
90890-06634
C Driver rod
(intermediate shaft and jet pump)
P/N. YB-06071
90890-06606
D Bearing inner/outer race attachment
(jet pump bearing)
P/N. YB-34474
E Shaft holder (intermediate shaft)
P/N. YB-06552
90890-06552
F Bearing outer race attachment
(intermediate shaft)
P/N. YB-06016
90890-06626
90890-06551
3
YB-06117
4
YB-06151
6
90890-06521
5
YB-06096
90890-06501
7
90890-06535
8
90890-06536
9
90890-06538
0
90890-06652
B
YB-06156
C
YB-06071
E
YB-06552
90890-06552
90890-06519
A
YB-06112
YB-06196
90890-06614
90890-06653
90890-06634
90890-06606
F
D
YB-06016
YB-34474
90890-06626
1-6
SPEC
E
CHAPTER 2
SPECIFICATIONS
GENERAL SPECIFICATIONS.......................................................................... 2-1
MAINTENANCE SPECIFICATIONS................................................................ 2-3
ENGINE..................................................................................................... 2-3
JET PUMP UNIT....................................................................................... 2-4
HULL AND HOOD .................................................................................... 2-4
ELECTRICAL ............................................................................................. 2-5
TIGHTENING TORQUES ................................................................................ 2-7
SPECIFIED TORQUES .............................................................................. 2-7
GENERAL TORQUE ............................................................................... 2-10
CABLE AND HOSE ROUTING...................................................................... 2-11
1
2
3
4
5
6
7
8
9
SPEC
GENERAL SPECIFICATIONS
E
GENERAL SPECIFICATIONS
Item
MODEL CODE
Hull
Engine
DIMENSIONS
Length
Width
Height
Dry weight
Watercraft capacity
PERFORMANCE
Maximum output
Maximum fuel consumption
Cruising range
ENGINE
Engine type
Number of cylinders
Displacement
Bore × stroke
Compression ratio
Intake system
Carburetor model
(manufacturer) × quantity
Enrichment control
Scavenging system
Lubrication system
Cooling system
Starting system
Ignition system
Ignition timing
Spark plug model
(manufacturer)
Battery capacity
Lighting coil
Propulsion system
DRIVE UNIT
Jet pump type
Impeller rotation (from rear)
Transmission
Nozzle angle (horizontal)
Nozzle angle (vertical)
Trim system
Model
GP800R
Unit
F0W
68A
mm (in)
mm (in)
mm (in)
kg (lb)
2,930 (115.4)
1,150 (45.3)
1,020 (40.2)
268 (591)
2
kW (PS) @ r/min
R/h (US gal/h,
lmp gal/h)
h
88.2 (120) @ 7,000
49 (12.9, 10.8)
cm3 (cu. in)
mm (in)
1.2
2-stroke
2
784 (47.8)
80.0 × 78.0 (3.15 × 3.07)
6.6:1
Reed valve
BN44 (Mikuni) × 2
Choke valve
Loop charge
Oil injection
Water
Electric
Digital CDI
15 BTDC–20 BTDC
BR8ES (NGK)
Degree
V/Ah (kC)
max. A @ r/min
12/19 (68.4)
8 @ 6,000
Jet pump
Axial flow, single stage
Counterclockwise
Direct drive from engine
23 + 23
–5, 0, 5, 10, 15
Manual 5 positions
Degree
Degree
2-1
SPEC
GENERAL SPECIFICATIONS
Item
FUEL AND OIL
Fuel
Fuel rating
Model
GP800R
Unit
Regular unleaded gasoline
86
90
YAMALUBE 2-W or an equivalent TC-W3
certified outboard oil
30:1
PON*
RON*
Oil
Fuel/oil mixing ratio
(wide open throttle)
Fuel tank capacity
Fuel tank reserve capacity
Oil tank capacity
E
R(US gal,
Imp gal)
R(US gal,
Imp gal)
R(US gal,
Imp gal)
60 (15.9, 13.2)
10 (2.6, 2.2)
5.5 (1.45, 1.21)
PON*: Pump Octane Number = (Motor Octane Number + Research Octane Number)/2
RON*: Research Octane Number
2-2
SPEC
MAINTENANCE SPECIFICATIONS
E
MAINTENANCE SPECIFICATIONS
ENGINE
Item
CYLINDER HEAD
Warpage limit
Compression pressure*1
CYLINDERS
Bore size
Taper limit
Out-of-round limit
Wear limit
PISTONS
Diameter
Measuring point*
Piston-to-cylinder clearance
Wear limit
Piston pin bore inside
diameter
PISTON RINGS
Top
Type
Dimensions (B)
Dimensions (T)
End gap
Ring groove clearance
2nd*2
Type
Dimensions (B)
Dimensions (T)
End gap
Ring groove clearance
PISTON PINS
Diameter
Wear limit
Unit
Model
GP800R
mm (in)
kPa (kg/cm2)
0.1 (0.004)
560 (5.6)
mm (in)
mm (in)
mm (in)
mm (in)
80.000–80.018 (3.1496–3.1503)
0.08 (0.003)
0.05 (0.002)
Original cylinder bore + 0.04 (0.0016)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
Red: 79.899–79.902 (3.1456–3.1457)
Orange: 79.903–79.906 (3.1458–3.1459)
Green: 79.907–79.910 (3.1459–3.1461)
Purple: 79.911–79.914 (3.1461–3.1462)
22 (0.87)
0.100–0.105 (0.0039–0.0041)
Cylinder bore – 0.105 (0.0041)
22.004–22.025 (0.8663–0.8671)
mm (in)
mm (in)
mm (in)
mm (in)
Keystone
1.2 (0.05)
2.85 (0.112)
0.30–0.45 (0.012–0.018)
0.03–0.05 (0.001–0.002)
mm (in)
mm (in)
mm (in)
mm (in)
Keystone
1.2 (0.05)
2.85 (0.112)
0.30–0.45 (0.012–0.018)
0.03–0.05 (0.001–0.002)
mm (in)
mm (in)
21.995–22.000 (0.8659–0.8661)
21.990 (0.8657)
*1: At 760 mmHg and 20 ˚C (68 ˚F)
*2: The top ring and 2nd ring are of the same type.
2-3
SPEC
MAINTENANCE SPECIFICATIONS
Item
CRANKSHAFT ASSEMBLY
Crank width A
Deflection limit B
Big end side clearance C
Maximum small end axial
play D
CARBURETORS
Type
Identification mark
Main nozzle
Main jet
Pilot jet
Throttle valve
Valve seat size
Trolling speed
REED VALVES
Thickness
Reed valve stopper height
Reed valve warpage limit
E
Unit
Model
GP800R
mm (in)
mm (in)
mm (in)
mm (in)
72.95–73.00 (2.872–2.874)
0.05 (0.002)
0.25–0.75 (0.010–0.030)
2.0 (0.08)
mm (in)
r/min
Floatless
#1: 68A-01, #2: 68A-02
3.0 (0.12)
150
90
120
1.2 (0.05)
1,300 ± 50
mm (in)
mm (in)
mm (in)
0.52 (0.020)
10.8–11.4 (0.43–0.45)
0.2 (0.01)
Unit
Model
GP800R
mm (in)
JET PUMP UNIT
Item
JET PUMP
Impeller material
Number of impeller blades
Impeller pitch angle
Impeller clearance
Impeller clearance limit
Drive shaft runout limit
Nozzle diameter
Stainless steel
3
13.2
0.35–0.45 (0.014–0.018)
0.6 (0.024)
0.3 (0.012)
86.8 (3.42)
Degree
mm (in)
mm (in)
mm (in)
mm (in)
HULL AND HOOD
Item
FREE PLAY
YPVS cable slack
Throttle lever free play
Unit
Model
GP800R
mm (in)
mm (in)
0.5–1.5 (0.02–0.06)
4–7 (0.16–0.28)
2-4
SPEC
MAINTENANCE SPECIFICATIONS
E
ELECTRICAL
Item
BATTERY
Type
Capacity
CDI UNIT
(O – B)
Output peak voltage lower
limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
STATOR
Charge coil
(Br – L)
Output peak voltage
lower limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
Pickup coil (W/R – W/B)
Output peak voltage
lower limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
Lighting coil
(G – G)
Output peak voltage
lower limit
@cranking 1
@cranking 2
@2,000 r/min
@3,500 r/min
Charge coil resistance
Pickup coil resistance
Lighting coil resistance
Minimum charging current
IGNITION COIL
Minimum spark gap
Primary coil resistance
Secondary coil resistance
Model
GP800R
Unit
V/Ah (kC)
Fluid
12/19 (68.4)
V
V
V
V
85
110
205
200
V
V
V
V
90
120
220
210
V
V
V
V
5
3
7
11
V
V
V
V
Ω (color)
Ω (color)
Ω (color)
A @ r/min
8.5
8.5
13
13
299–365 (Br – L)
446–545 (W/R – W/B)
0.86–1.06 (G – G)
9 @ 6,000
mm (in)
Ω (color)
kΩ
10 (0.39)
0.078–0.106 (O – B)
14.3–30.5
(#1 Spark plug cap – #2 Spark plug cap)
Cranking 1: unloaded
Cranking 2: loaded
2-5
SPEC
MAINTENANCE SPECIFICATIONS
Item
RECTIFIER/REGULATOR
(R – B)
Output peak voltage lower
limit (unloaded)
@cranking
@2,000 r/min
@3,500 r/min
THERMO SWITCH
On temperature
Off temperature
STARTER MOTOR
Brush length
Wear limit
Commutator undercut
Limit
Commutator diameter
Limit
FUSE
Rating
E
Unit
Model
GP800R
V
V
V
7.5
12.5
12.5
˚C (˚F)
˚C (˚F)
80 (177)
70 (159)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
12.5 (0.49)
6.5 (0.26)
0.7 (0.03)
0.2 (0.01)
28.0 (1.10)
27.0 (1.06)
V/A
12/10
2-6
SPEC
TIGHTENING TORQUES
E
TIGHTENING TORQUES
SPECIFIED TORQUES
2-7
M8
2
M10
8
M3
M6
2
10
1.0
7.2
M6
M5
M4
M14
6
2
2
2
M8
10
M10
8
10
4
3
25
15
37
22
39
1.0
0.4
0.3
2.5
1.5
3.7
2.2
3.9
7.2
2.9
2.2
18
11
27
16
28
M6
1
5
0.5
3.6
M10
1
74
7.4
53
LT
1
572
M10
LT
5
271
M8
LT
1
271
M10
LT
3
271
M8
LT
2
271
M8
LT
1
271
M10
LT
1
271
M10
LT
2
242
M10
LT
4
572
M10
LT
2
572
M10
LT
12
1.4
37
1.4
28
1.4
37
1.4
35
1.4
35
11
28
11
24
11
37
12
24
1.4
35
1.4
27
17
37
0.58
271
1.7
0.2
5.1
0.2
3.9
0.2
5.1
0.2
4.9
0.2
4.9
1.5
3.9
1.5
3.3
1.5
5.1
1.7
3.4
0.2
4.9
0.2
3.7
2.3
5.1
0.08
LT
16
17
2
51
2
39
2
51
2
49
2
49
15
39
15
33
15
51
17
34
2
49
2
37
23
51
0.8
242
4
LT
1st
Bolt
4th
2nd
Bolt
6th
Exhaust chamber
3rd
Nut
assembly – muffler stay 1
5th
– muffler stay 3
7th
Bolt
9th
8th
Bolt
10th
1st
Nut
2nd
1st
Exhaust chamber –
Bolt
muffler
2nd
1st
Nut
2nd
1st
Exhaust chamber joint –
Bolt
exhaust manifold
2nd
1st
Bolt
3rd
Exhaust chamber joint –
muffler stay
2nd
Bolt
4th
1st
Exhaust manifold –
Bolt
cylinder
2nd
Reed valve – reed valve seat
Screw
YPVS cable bracket – YPVS cover
Bolt
– cylinder
YPVS cover – cylinder
Bolt
YPVS valve assembly – cylinder
Bolt
YPVS valve lever – shaft
Bolt
Spark plug – cylinder head
Spark plug
1st
Cylinder head – cylinder
Bolt
2nd
1st
Cylinder – crankcase
Bolt
2nd
Starter motor lead – starter
Nut
motor
Flywheel magneto – crankshaft
Bolt
assembly
M8
Remarks
572
Bolt
Tightening torque
N•m kgf•m ft•lb
LT
Thread
Q’ty
size
572
ENGINE UNIT
Engine unit – engine mount
Part name
E
Part to tightened
TIGHTENING TORQUES
Driven coupling – shaft
Grease nipple – intermediate
housing
HULL AND HOOD
Handlebar cover – handlebar
cover stay
Handlebar cover stay – steering
column
Upper handlebar holder/lower
handle holder – steering column
QSTS converter – hull
QSTS cable 1, 2 locknut
Throttle lever assembly –
handlebar
M16
1
74
7.4
53
Impeller
M22
1
18
1.8
13
Nut
Screw
Bolt
Driven
coupling
M10
M5
M8
4
1
3
26
4
17
2.6
0.4
1.7
19
2.9
12
M27
1
36
3.6
25
Nipple
—
1
5
0.5
3.6
Screw
M6
4
1.1
0.11
0.8
Screw
M6
4
2.9
0.29
2.1
Bolt
M8
4
16
1.6
11
Nut
Nut
M6
M8
2
2
5
16
0.5
1.6
3.6
11
Screw
M5
2
3
0.3
2.2
2-8
LT
Nut
572
5.1
LT
0.7
271
7
LT
4
242
M6
LT
Bolt
242
12
12
5.1
2.9
11
11
LT
1.7
1.7
0.7
0.4
1.5
1.5
242
17
17
7
4
15
15
LT
4
4
4
4
2
2
572
M8
M8
M6
M5
M8
M8
LT
5.1
271
0.7
LT
7
242
Bolt
Bolt
Bolt
Screw
Bolt
Bolt
1
LT
M6
572
Nut
LT
6
572
M8
LT
Bolt
572
7
LT
M6
242
13
LT
M8
Bolt
271
2
2
3
11
19
3.6
10
10
11
19
8.0
11
19
LT
M5
M6
M6
1.5
2.7
0.5
1.4
1.4
1.5
2.7
1.1
1.5
2.7
271
Bolt
Bolt
Bolt
15
27
5
14
14
15
27
11
15
27
LT
8
25
572
M8
3.6
LT
Bolt
36
572
1
LT
M27
Remarks
572
Drive
coupling
Tightening torque
N•m kgf•m ft•lb
LT
1st
Mount bracket –
crankcase
2nd
JET PUMP UNIT
Steering cable joint – nozzle
deflector
Ride plate – hull
Intake duct – hull
Intake grate – hull
Speed sensor – ride plate
Nozzle ring – nozzle
Nozzle deflector – nozzle ring
Water inlet cover – water inlet
strainer – impeller duct
Drive shaft nut – drive shaft
Impeller (left-hand threads) –
drive shaft
Transom plate – hull
Bilge strainer holder – bulkhead
Intermediate housing – bulkhead
Thread
Q’ty
size
572
Drive coupling – crankshaft
assembly
1st
Generator cover –
crankcase
2nd
Pickup coil – generator cover
Cable holder – generator cover
Stator coil – generator cover
1st
Lower crankcase – upper
2nd
crankcase
Part name
LT
Part to tightened
E
572
SPEC
TIGHTENING TORQUES
Handlebar switch assembly –
handlebar
QSTS grip assembly – handlebar
Grip end – handlebar
Choke lever assembly –
handlebar
QSTS cable housing – cover
Plate/steering column assembly
– deck
Steering column assembly – deck
Steering arm – steering column
Steering cable ball joint –
steering arm
Handlebar stopper – steering
column housing
QSTS cable locknut
(nozzle ring side)
QSTS cable – hull
QSTS cable end – pin – QSTS
converter
Steering cable locknut
(nozzle deflector side)
Steering cable – hull
Steering cable holder – bracket
Speed sensor lead – hull
Hinge assembly – front hood
Wind shield – front hood
Hood lock – front hood
Hinge assembly – deck
Steering console cover assembly
– deck
Multifunction meter – holder
Steering console cover – side
cover
Steering console cover – glove
compartment
Steering cable bracket – deck
Buzzer bracket – deck – steering
cable bracket
Hood lock assembly – deck
Seat lock assembly – seat
Bracket/deck – notch
Bracket/deck – hand grip
Part name
Thread
Q’ty
size
Tightening torque
N•m kgf•m ft•lb
Screw
M5
2
3
0.3
2.2
Screw
Bolt
M6
M5
1
2
3
1
0.3
0.1
2.2
0.7
Screw
M5
2
3
0.3
2.2
Screw
M4
1
1
0.1
0.7
Nut
M8
2
16
1.6
11
Nut
Nut
M8
M8
2
1
16
16
1.6
1.6
11
11
Nut
M6
1
5
0.5
3.6
Nut
M10
1
26
2.6
19
Nut
M5
1
3
0.3
2.2
Nut
—
1
6
0.6
4.3
Nut
M6
1
4
0.4
2.9
Nut
M6
1
6
0.6
4.3
Nut
Bolt
Nut
Bolt
Screw
Bolt
Nut
Nut
Bolt
Screw
Nut
Nut
—
M6
—
M6
M5
M6
M8
M6
M6
M5
M8
M5
1
1
1
2
8
2
2
2
4
2
2
2
6
6
6
12
1
5
16
5
3
2
16
2
0.6
0.6
0.6
1.2
0.1
0.5
1.6
0.5
0.3
0.2
1.6
0.2
4.3
4.3
4.3
8.7
0.7
3.6
11
3.6
2.2
1.4
11
1.4
Screw
M6
4
3
0.3
2.2
Screw
M5
4
1
0.1
0.7
Bolt
M6
1
6
0.6
4.3
Bolt
M6
2
6
0.6
4.3
Nut
Bolt
Nut
Bolt
M6
M6
M10
M8
2
2
1
2
6
6
26
5
0.6
0.6
2.6
0.5
4.3
4.3
19
3.6
2-9
Remarks
LT
Part to tightened
E
572
SPEC
TIGHTENING TORQUES
Part name
Hand grip – deck
Seat bracket – deck
Battery box/stay – holder
Battery box – bracket/deck
Battery box – electrical box
Extension bolt – battery negative
terminal
Exhaust outlet – hull
Sponson – hull
Spout – hull
Rope hole – hull
Bow eye – hull
Flap – hull
Drain plug/packing – hull
Engine mount – hull
Engine damper – hull
Nut
Nut
Nut
Nut
Bolt
Nut A
Bolt B
8 mm
10 mm
12 mm
14 mm
17 mm
M5
M6
M8
M10
M12
Thread
Q’ty
size
M8
2
M8
2
M6
2
M8
2
M8
3
Tightening torque
N•m kgf•m ft•lb
5
0.5
3.6
15
1.5
11
9
0.9
6.5
13
1.3
9.4
15
1.5
11
Bolt
M6
1
6
0.6
4.3
Bolt
Bolt
Nut
Nut
Bolt
Bolt
Nut
Bolt
Bolt
M6
M8
M24
M24
M6
M6
M5
M8
M6
3
6
1
2
2
8
4
8
2
6
18
5
5
13
6
2
17
6
0.6
1.8
0.5
0.5
1.3
0.6
0.2
1.7
0.6
4.3
13
3.6
3.6
9.4
4.3
1.4
12
4.3
Remarks
LT
Part to tightened
E
572
SPEC
GENERAL TORQUE
General torque
specifications
N•m kgf•m ft•lb
5.0
0.5
3.6
8.0
0.8
5.8
18
1.8
13
36
3.6
25
43
4.3
31
This chart specifies tightening torques for
standard fasteners with a standard ISO
thread pitch. Tightening torque specifications for special components or assemblies
are provided in applicable sections of this
manual. To avoid warpage, tighten multifastener assemblies in a crisscross fashion
and progressive stages until the specified
tightening torque is reached. Unless otherwise specified, tightening torque specifications require clean, dry threads.
Components should be at room temperature.
2-10
SPEC
CABLE AND HOSE ROUTING
E
CABLE AND HOSE ROUTING
2
A
F
2
A
1
B
CB
L
20˚
K
K
E
D
E
2
E
E
B
D
2
C
F
K
F
2
L
A
3
D-D
J
I
K-K
K
K
9
0
I
9
0
A
J
J
J
J
G
G
4
I
H
H
H
J-J
E-E
C
G
D
9
0
E
F
I-I
5
6
7
F-F
9
4
8
H-H
1
2
3
4
5
6
7
8
Fuel filter
Fuel tank breather hose
Fuel hose
Cooling water hose
Choke cable
Throttle cable
Oil return hose
Bilge hose
G-G
9
0
A
B
C
D
E
F
Speed sensor lead
Electrical box lead
YPVS cables
Cooling water pilot outlet
Battery negative lead
Battery
Steering cable
QSTS cable
2-11
G
H
I
J
K
Battery breather hose
Battery positive lead
Starter motor lead
Generator lead
YPVS servomotor
SPEC
CABLE AND HOSE ROUTING
E
D
1
2 3
D
E
A
E
D
E
C
B
H
I
2J
K
A
B
L
I
F
M
5
J
C
J
E A
0 A
8
G
F
4
7
4
G-G
E
A
F
G
9
H
G
H
G
J-J
F
E D C B
7
I
1
2
3
4
5
6
7
8
Oil delivery hose
Fuel return hose
Fuel suction hose
Speed sensor lead
QSTS cable
Cooling water hose
Steering cable
Flushing hose
H-H
9
0
A
B
C
D
E
Bilge hoses
To multifunction meter
To stator assembly
To cylinder #1
To cylinder #2
To battery positive terminal
To starter motor positive
terminal
2-12
65
4
F
F
G
H
I
J
K
L
M
To thermoswitch
Battery negative lead
Buzzer lead
Choke cable
YPVS servomotor
YPVS cables
Battery positive lead
Battery breather hose
INSP
ADJ
E
CHAPTER 3
PERIODIC INSPECTION AND ADJUSTMENT
MAINTENANCE INTERVAL CHART .............................................................. 3-1
PERIODIC SERVICE ........................................................................................ 3-2
CONTROL SYSTEM ................................................................................. 3-2
Steering column inspection ............................................................. 3-2
Steering cable inspection and adjustment ..................................... 3-2
Throttle cable inspection and adjustment ...................................... 3-3
Choke cable inspection and adjustment ......................................... 3-4
QSTS cable inspection and adjustment .......................................... 3-5
YPVS cable adjustment .................................................................... 3-6
FUEL SYSTEM.......................................................................................... 3-7
Fuel line inspection ........................................................................... 3-7
Trolling speed check and adjustment ............................................. 3-8
OIL INJECTION SYSTEM......................................................................... 3-9
Oil line inspection ............................................................................. 3-9
POWER UNIT............................................................................................ 3-9
Spark plug inspection ....................................................................... 3-9
ELECTRICAL ........................................................................................... 3-10
Battery inspection ........................................................................... 3-10
JET PUMP UNIT..................................................................................... 3-13
Impeller inspection ......................................................................... 3-13
Water inlet strainer inspection....................................................... 3-14
Bilge strainer inspection................................................................. 3-14
GENERAL................................................................................................ 3-14
Drain plug inspection...................................................................... 3-14
Lubrication points ........................................................................... 3-15
1
2
3
4
5
6
7
8
9
INSP
ADJ
MAINTENANCE INTERVAL CHART
E
MAINTENANCE INTERVAL CHART
The following chart should be considered strictly as a guide to general maintenance intervals.
Depending on operating conditions, the intervals of maintenance should be changed.
Initial
Item
CONTROL SYSTEM
Steering cable
Steering column
Throttle cable
Carburetor throttle shaft
Choke cable
QSTS cable
YPVS cable
FUEL SYSTEM
Fuel tank
Fuel filter
Fuel line
Trolling speed
Carburetor setting
OIL INJECTION SYSTEM
Oil injection system
Oil pump cable
POWER UNIT
Spark plugs
Cooling water passage
Rubber coupling
ELECTRICAL
Battery
JET PUMP UNIT
Impeller
Water inlet strainer
Bilge strainer
GENERAL
Bolts and nuts
Drain plugs
Lubrication points
Intermediate housing
Remarks
Every
10 hours 50 hours 100 hours 200 hours
(Break-in) (3 months) (6 months) (1 year)
Refer to
page
Inspect/adjust
Inspect
Inspect/adjust
Inspect/adjust
Inspect/adjust
Inspect/adjust
Inspect/adjust
3-2
3-2
3-3
—
3-4
3-5
3-6
Clean
Clean/replace
Inspect
Check/adjust
Inspect/adjust
4-9
3-7
3-7
3-8
4-18
Check/clean
Inspect/adjust
3-9
4-30
Inspect/clean/adjust
Inspect/clean
Inspect
*1
3-9
—
—
Inspect
*2
3-10
Inspect
Clean
Clean
3-13
3-14
3-14
Retighten
Inspect/replace
Grease
Grease
—
3-14
3-15
3-17
*3
*1: After every ride
*2: Inspect fluid level before every ride
*3: Grease capacity 33.0–35.0 cm3 (1.11–1.18 oz)
*4: Grease capacity 6.0–8.0 cm3 (0.20–0.27 oz)
3-1
*4
INSP
ADJ
CONTROL SYSTEM
E
PERIODIC SERVICE
CONTROL SYSTEM
Steering column inspection
1. Inspect:
● Steering column
Excessive play → Replace the steering column.
Refer to “STEERING COLUMN” in
chapter 8.
Inspection steps:
● Move the handlebar up and down and
back and forth.
● Check the excessive play of the handlebar.
Steering cable inspection and adjustment
1. Inspect:
● Distance a, b (between the nozzle
and nozzle deflector)
Out of specification → Adjust.
Inspection steps:
● Set the control grip in the neutral position.
● Turn the handlebar from lock to lock.
● Measure distances a and b.
● If the difference is not within specification, adjust the cable joint.
Difference of distances a and b:
Maximum 5 mm (0.2 in)
2. Adjust:
● Steering cable joint
(steering column side)
Adjustment steps:
● Loosen the locknut 1.
● Disconnect the steering cable joint 2
from the ball joint 3.
● Turn the cable joint in or out for adjusting the distances a and b.
2
1
3
3-2
Turn in
Distance a is increased.
Turn out
Distance b is increased.
INSP
ADJ
CONTROL SYSTEM
E
WARNING
The cable joint must be screwed in more
than 8 mm (0.31 in).
●
Connect the cable joint and tighten the
locknut.
T.
Locknut:
6 N • m (0.6 kgf • m, 4.3 ft • lb)
R.
NOTE:
If the steering cable cannot be properly
adjusted at the steering column side, make
sure the steering cable at the jet pump side
is set to the specified length. Refer to
“REMOTE CONTROL CABLES AND SPEED
SENSOR LEAD” in chapter 8.
Throttle cable inspection and adjustment
NOTE:
Before adjusting the throttle lever free play,
adjust the trolling speed.
1. Measure:
● Throttle lever free play a
Out of specification → Adjust.
Throttle lever free play:
4–7 mm (0.16–0.28 in)
2. Adjust:
● Throttle lever free play
Adjustment steps:
Loosen the locknut 1.
● Turn the adjuster 2 in or out until the
specified free play is obtained.
●
Turn in
Free play is increased.
Turn out
Free play is decreased.
●
3-3
Tighten the locknut.
INSP
ADJ
CONTROL SYSTEM
E
WARNING
After adjusting the free play, turn the handlebar to the right and left and make sure
that the trolling speed does not increase.
Choke cable inspection and adjustment
1. Check:
● Choke lever operation
Incorrect operation → Adjust.
Checking steps:
● Check that the choke lever moves back
slightly when it is fully opened.
● Check that the inner cable has some
slack when the choke lever is completely closed.
2. Adjust:
● Choke lever operation
Adjustment steps:
● Loosen the locknut 1.
● Screw the adjuster 2 fully into the
bracket.
● Align the choke lever end a within the
line marks b.
● Turn out the adjuster 2 until the inner
cable is taut.
NOTE:
If the inner cable is difficult to make taut
using the adjuster 2, adjust the choke
lever so that the cable is taut. The cable
must be taut when the choke lever end
a is positioned within the line marks b.
Reset the adjuster if necessary.
●
3-4
Tighten the locknut 1.
INSP
ADJ
CONTROL SYSTEM
E
QSTS cable inspection and adjustment
1. Measure:
● Nozzle deflector set length a, b
Difference → Adjust.
Measurement steps:
Set the control grip in the neutral position.
● Measure the nozzle deflector set
length a and b.
● If a and b length are not even, adjust
the cable joint.
●
2. Adjust:
● QSTS cable
Adjustment steps:
● Set the control grip in the neutral position.
● Loosen the locknut 1.
● Remove the nut 2 and pivot pin 3.
● Set the nozzle deflector in the center
position.
● Turn the cable joint 4 for adjusting.
Turn in
Length b is increased.
Turn out
Length a is increased.
WARNING
The cable joint must be screwed in more
than 8 mm (0.31 in).
●
Connect the cable joint 4 and pivot
pin 3 and tighten the nut 2.
T.
Nut:
4 N • m (0.4 kgf • m, 2.9 ft • lb)
R.
●
Tighten the locknut 1.
T.
R.
3-5
Locknut:
4 N • m (0.4 kgf • m, 2.9 ft • lb)
INSP
ADJ
CONTROL SYSTEM
E
NOTE:
If the QSTS cable cannot be properly
adjusted at the QSTS converter side, make
sure the QSTS cable at the jet pump side is
set to the specified length.
Refer to “REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD” in chapter 8.
YPVS cable adjustment
1. Check:
● YPVS valve position
Incorrect position → Adjust the YPVS
cable.
Checking steps:
● Start the engine and then stop it.
NOTE:
When the engine has been stopped for 3
seconds, the YPVS valve assembly will
retract and extend one time.
●
Check that the hole a in the pulley is
aligned with the hole in the cylinder
when the YPVS valve is fully closed.
2. Measure:
● YPVS cable slack a
Out of specification → Adjust.
YPVS cable slack:
0.5–1.5 mm (0.02–0.06 in)
3-6
INSP
ADJ
CONTROL SYSTEM/FUEL SYSTEM
E
3. Adjust:
● YPVS cables 1 and 2
4
1
3
2
Adjustment steps:
Loosen locknuts 1 and 2.
● Turn in adjusters 3 and 4 until there
is slack in the cables.
● Align the hole a in the pulley with the
hole in the cylinder.
● Insert a 4-mm-diameter pin through
the holes in the pulley and cylinder.
● Turn adjusters 3 and 4 in or out until
the specified slack is obtained.
●
Turn in
Slack is increased.
Turn out
Slack is decreased.
●
●
●
●
●
●
Finger tighten locknuts 1 and 2.
Remove the pin.
Start and stop the engine.
Recheck the hole alignment.
If the hole alignment is correctly,
tighten the locknuts.
If the hole alignment is incorrect,
repeat the above steps.
FUEL SYSTEM
WARNING
● Stop
the engine, set the fuel cock to
“OFF” before servicing the fuel system.
● When removing fuel system parts, wrap
them in a cloth and take care that no fuel
spills into the engine compartment.
Fuel line inspection
1. Inspect:
● Fuel filter 1
Contaminants → Replace.
Cracks/damage → Replace.
Water contamination → Replace and
check the fuel tank.
● Fuel hoses
● Fuel tank
● Fuel hoses through part
● Fuel filler cap
Cracks/damage → Replace.
3-7
INSP
ADJ
FUEL SYSTEM
E
2. Inspect:
● Water separator 1
Water accumulation → Drain.
NOTE:
If need the water draining, remove the drain
plug 2.
Trolling speed check and adjustment
1. Check:
● Trolling speed
Out of specification → Adjust.
Trolling speed:
1,300 ± 50 r/min
Checking steps (with the watercraft in
the water):
● Start the engine and allow it to warm
up for several minutes.
● Attach the engine tachometer to the
spark plug lead.
Engine tachometer:
YU-8036-A/90890-06760
●
Measure the engine trolling speed.
2. Adjust:
● Trolling speed
Adjustment steps:
Start the engine and allow it to warm
up for several minutes.
● Attach the engine tachometer to the
spark plug lead.
●
1
Engine tachometer:
YU-8036-A/90890-06760
●
3-8
Turn the throttle stop screw 1 in or
out until the specified trolling speed is
obtain.
INSP
ADJ
OIL INJECTION SYSTEM/POWER UNIT
E
OIL INJECTION SYSTEM
Oil line inspection
1. Inspect:
● Oil filter
Contaminants → Clean.
Frays/tears → Replace.
● Rubber seal
Cracks/wear → Replace.
● Oil hoses
● Oil tank
● Oil filler cap
Cracks/damage → Replace.
● Check valve
Malfunction → Replace.
CAUTION:
Do not allow the oil tank to become completely empty. If the oil tank becomes
empty the oil injection pump must be bled
to ensure proper oil flow, otherwise engine
damage may occur. Refer to “OIL PUMP” in
chapter 4.
POWER UNIT
Spark plug inspection
1. Inspect:
● Electrodes 1
Damage/wear → Replace.
● Insulator color 2
Distinctly different color → Check the
engine condition.
Color guide:
Medium to light tan color:
Normal
Whitish color:
Lean fuel mixture
Air leak
Incorrect settings
Blackish color:
Overly rich mixture
Electrical malfunction
Excessive oil use
Defective spark plug
2. Clean:
● Spark plug
(with a spark plug cleaner or wire
brush)
3-9
INSP
ADJ
POWER UNIT/ELECTRICAL
E
3. Measure:
● Spark plug gap a
Out of specification → Regap.
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
4. Tighten:
● Spark plug
T.
Spark plug:
25 N • m (2.5 kgf • m, 18 ft • lb)
R.
NOTE:
● Before installing the spark plug, clean the
gasket surface and spark plug surface.
Also, it is suggested to apply a thin film of
anti-seize compound to the spark plug
threads to prevent thread seizure.
● If a torque wrench is not available, a good
estimate of the correct tightening torque
for a new spark plug is to finger tighten a
the spark plug and then tighten it another
1/4 to 1/2 of a turn b.
ELECTRICAL
Battery inspection
WARNING
Battery electrolyte is dangerous; it contains
sulfuric acid which is poisonous and highly
caustic.
Always follow these preventive measures:
● Avoid bodily contact with electrolyte as it
can cause severe burns or permanent eye
injury.
● Wear protective eye gear when handling
or working near batteries.
Antidote (EXTERNAL):
● SKIN - Wash with water.
● EYES - Flush with water for 15 minutes
and get immediate medical attention.
3-10
INSP
ADJ
ELECTRICAL
E
Antidote (INTERNAL):
● Drink large quantities of water or milk followed with milk of magnesia, beaten egg
or vegetable oil. Get immediate medical
attention.
Batteries generate explosive, hydrogen
gas. Always follow these preventive measures:
● Charge batteries in a well-ventilated area.
● Keep batteries away from fire, sparks or
open flames (e.g., welding equipment,
lighted cigarettes).
● DO NOT SMOKE when charging or handling batteries.
KEEP BATTERIES AND ELECTROLYTE OUT
OF REACH OF CHILDREN.
CAUTION:
● Do
not place the battery on its side.
● Before adding electrolyte or recharging,
be sure to remove the battery from the
battery box.
● Make sure that the battery breather hose
is properly connected and is not pinched
or damaged.
1. Remove:
● Band
● Battery negative lead 1
● Battery positive lead 2
● Battery
● Battery breather hose 3
WARNING
● When
removing the battery, disconnect
the negative lead first.
● Remove the battery to prevent acid loss
during turning the machine on its side for
the impeller service.
3-11
INSP
ADJ
ELECTRICAL
E
2. Inspect:
● Electrolyte level
Low → Add distilled water.
The electrolyte level should be
between the upper a and lower b
level marks.
Filling steps:
Remove each filler cap.
● Add distilled water.
● When the electrolyte level reaches the
upper level mark, allow the cell to
stand for 20 minutes. If the electrolyte
level drops, add more distilled water
so the level reaches the upper level
mark.
●
CAUTION:
Use only distilled water. Other types of
water contain minerals which are harmful
to batteries.
3. Inspect:
● Specific gravity
Out of specification → Charge.
Specific gravity at 20 ˚C (68 ˚F):
1.28
Charging current:
1.9 amps × 10 hrs (68.4 kC)
4. Install:
● Filler caps
CAUTION:
Before installation, rinse off any fluid from
the battery box and battery and make sure
that the battery is dry before installing it.
3-12
INSP
ADJ
ELECTRICAL/JET PUMP UNIT
E
5. Install:
● Battery breather hose 1
● Battery
● Battery positive lead 2
● Battery negative lead 3 (with terminal extension at battery negative terminal)
● Band
CAUTION:
● Connect
the positive lead to the battery
terminal first.
● Make sure the battery leads are connected properly. Reversing the leads can
seriously damage the electrical system.
● Make sure that the battery breather hose is
properly connected and is not obstructed.
● Coat the terminals with a water resistant
grease to minimize terminal corrosion.
JET PUMP UNIT
Impeller inspection
1. Check:
● Impeller 1
Damage/wear → Replace.
Nicks/scratches → File or grind.
2. Measure:
● Impeller-to-housing clearance a
Out of specification → Replace.
Max. impeller-to-housing
clearance:
0.6 mm (0.02 in)
Measurement steps:
● Remove the battery leads.
● Remove the intake grate 1 and intake
duct 2.
● Measure the clearance at each impeller blade as shown (a total of three
measurements).
● Install the intake grate and intake duct.
T.
R.
●
3-13
Bolt:
M6: 7 N • m
(0.7 kgf • m, 5.1 ft • lb)
M8: 17 N • m
(1.7 kgf • m, 12 ft • lb)
Install the battery leads.
INSP
ADJ
JET PUMP UNIT/GENERAL
E
Water inlet strainer inspection
1. Inspect:
● Water inlet strainer
Contaminants → Clean.
Cracks/damage → Replace.
a
Inspection steps:
Remove the water inlet cover 1.
● Inspect the water inlet strainer mesh
a.
● Install the water inlet cover.
●
1
Bilge strainer inspection
1. Inspect:
● Bilge strainer
Contaminants → Clean.
Cracks/damage → Replace.
Inspection steps:
● Disconnect the bilge strainer 1 from
the bilge strainer holder.
● Inspect the bilge strainer.
1
GENERAL
Drain plug inspection
1. Inspect:
● Drain plugs
Cracks/damage → Replace.
● O-rings
Cracks/wear → Replace.
● Screw threads
Contaminants → Clean.
3-14
INSP
ADJ
GENERAL
E
Lubrication points
1. Lubricate:
● Throttle cable (handlebar side)
Recommended lubricant:
Rust inhibitor
NOTE:
Before lubricating the throttle cable,
squeeze the throttle lever and remove the
rubber seal 1.
2. Lubricate:
● QSTS control cables (handlebar side)
Recommended lubricant:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
NOTE:
Before lubricating the QSTS control cables,
remove the QSTS cable housing cover.
Spray the rust inhibitor into the outer
cables, and apply grease to the inner
cables.
3. Lubricate:
● Choke cable (handlebar side)
Recommended lubricant:
Rust inhibitor
3-15
INSP
ADJ
GENERAL
E
4. Lubricate:
● Throttle cable (carburetor side)
● Oil pump cable
● QSTS cables (pulley side)
● YPVS cables
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
5. Lubricate:
● Nozzle pivot shaft
● Steering cable (nozzle side)
● QSTS cable (nozzle side)
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
3-16
INSP
ADJ
GENERAL
E
6. Lubricate:
● Steering cable
● Steering cable joint
NOTE:
Disconnect the joints and apply a small
amount of grease.
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
7. Fill:
● Intermediate housing
Recommended grease:
Yamaha marine grease,
Yamaha grease A
(Water resistant grease)
NOTE:
Fill the intermediate housing with the recommended grease through the grease nipples.
3-17
FUEL
E
CHAPTER 4
FUEL SYSTEM
FUEL COCK AND FUEL FILTER ..................................................................... 4-1
EXPLODED DIAGRAM ............................................................................. 4-1
REMOVAL AND INSTALLATION CHART ............................................... 4-1
SERVICE POINTS ..................................................................................... 4-2
Fuel filter inspection ......................................................................... 4-2
Fuel cock inspection.......................................................................... 4-2
OIL TANK ........................................................................................................ 4-3
EXPLODED DIAGRAM ............................................................................. 4-3
REMOVAL AND INSTALLATION CHART ............................................... 4-3
SERVICE POINTS ..................................................................................... 4-5
Oil line inspection ............................................................................. 4-5
Oil level sensor inspection ............................................................... 4-5
Oil tank inspection ............................................................................ 4-5
FUEL TANK ..................................................................................................... 4-6
EXPLODED DIAGRAM ............................................................................. 4-6
REMOVAL AND INSTALLATION CHART ............................................... 4-6
SERVICE POINTS ..................................................................................... 4-9
Check valve inspection ..................................................................... 4-9
Fuel level sensor inspection............................................................. 4-9
Fuel tank inspection .......................................................................... 4-9
Pipe joint inspection ......................................................................... 4-9
INTAKE SILENCER ....................................................................................... 4-10
EXPLODED DIAGRAM ........................................................................... 4-10
REMOVAL AND INSTALLATION CHART ............................................. 4-10
CARBURETOR UNIT..................................................................................... 4-11
EXPLODED DIAGRAM ........................................................................... 4-11
REMOVAL AND INSTALLATION CHART ............................................. 4-11
SERVICE POINTS ................................................................................... 4-18
Throttle valve synchronization inspection and adjustment ........ 4-18
Choke cable and throttle cable installation................................... 4-19
Oil pump cable installation ............................................................ 4-19
Carburetor assembly ...................................................................... 4-19
FUEL
CARBURETOR .............................................................................................. 4-20
EXPLODED DIAGRAM ........................................................................... 4-20
REMOVAL AND INSTALLATION CHART ............................................. 4-20
SERVICE POINTS ................................................................................... 4-23
Diaphragm inspection .................................................................... 4-23
Accelerator pump body inspection ............................................... 4-23
Arm inspection ................................................................................ 4-23
Regulator body inspection ............................................................. 4-24
Needle valve inspection ................................................................. 4-24
Jet and carburetor body inspection .............................................. 4-24
Carburetor assembly ...................................................................... 4-24
FUEL PUMP .................................................................................................. 4-25
EXPLODED DIAGRAM ........................................................................... 4-25
REMOVAL AND INSTALLATION CHART ............................................. 4-25
SERVICE POINTS ................................................................................... 4-27
Fuel pump inspection ..................................................................... 4-27
Fuel filter inspection ....................................................................... 4-27
OIL PUMP...................................................................................................... 4-28
EXPLODED DIAGRAM ........................................................................... 4-28
REMOVAL AND INSTALLATION CHART ............................................. 4-28
SERVICE POINTS ................................................................................... 4-30
Oil pump inspection........................................................................ 4-30
Oil hose inspection ......................................................................... 4-30
Check valve inspection ................................................................... 4-30
Oil pump cable adjustment ............................................................ 4-30
Oil injection pump air bleeding ..................................................... 4-31
E
1
2
3
4
5
6
7
8
9
FUEL
FUEL COCK AND FUEL FILTER
E
FUEL COCK AND FUEL FILTER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
FUEL COCK AND FUEL FILTER
REMOVAL
Screw
Knob
Nut
Fuel cock assembly
Fuel hose
Holder
Fuel filter
Fuel hose
Q’ty
Service points
Follow the left “Step” for removal.
1
1
1
1
3
1
1
1
Reverse the removal steps for installation.
4-1
FUEL
FUEL COCK AND FUEL FILTER
E
SERVICE POINTS
Fuel filter inspection
Refer to “FUEL SYSTEM” in chapter 3.
Fuel cock inspection
1. Check:
● Fuel cock
Contaminants → Clean.
Rough movement → Replace.
4-2
FUEL
OIL TANK
E
OIL TANK
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Procedure/Part name
OIL TANK REMOVAL
Engine unit
Steering console cover assembly
Q’ty
1
2
Oil level sensor coupler
Band
1
1
3
4
5
Nut
Oil filler neck
Rubber seal
1
1
1
4-3
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT” in chapter 5.
Refer to “STEERING CONSOLE COVER”
in chapter 8.
Not reusable
Disconnect the oil filler hose from the oil
filler neck.
FUEL
OIL TANK
E
EXPLODED DIAGRAM
Step
6
7
8
9
10
11
12
13
Procedure/Part name
Breather hose
Oil hose
Bolt
Tank belt
Oil tank assembly
Hose clamp
Oil filler hose
Oil level sensor
Q’ty
1
1
2
2
1
1
1
1
Service points
Reverse the removal steps for installation.
4-4
FUEL
OIL TANK
E
SERVICE POINTS
Oil line inspection
1. Inspect:
● Oil filter
Contaminants → Clean.
Frays/tears → Replace.
● Rubber seal
Cracks/wear → Replace.
● Oil hoses
● Oil tank
● Oil filler cap
Cracks/damage → Replace.
● Check valve
Malfunction → Replace.
Oil level sensor inspection
Refer to “INDICATION SYSTEM” in
chapter 7.
Oil tank inspection
1. Inspect:
● Oil tank
Cracks/damage → Replace.
4-5
FUEL
FUEL TANK
E
FUEL TANK
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
Procedure/Part name
FUEL TANK REMOVAL
Oil tank
Fuel level sensor coupler
Hose clamp
3
4
5
6
Nut
Fuel filler neck
Rubber seal
Fuel reserve hose
Q’ty
1
1
1
1
1
1
4-6
Service points
Follow the left “Step” for removal.
Refer to “OIL TANK”.
Disconnect the fuel filler hose from the
fuel filler neck.
FUEL
FUEL TANK
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
14
Procedure/Part name
Fuel hose
Fuel return hose
Fuel tank breather hose
Fuel tank assembly
Hose clamp
Fuel filler hose
Hose clamp
Fuel sensor assembly
Q’ty
1
1
1
1
1
1
1
1
4-7
Service points
FUEL
FUEL TANK
E
EXPLODED DIAGRAM
Step
15
16
17
18
19
20
21
22
Procedure/Part name
One way valve
Screw/washer
Filter
Screw/washer
Sleeve
Floatation
Bolt
Tank belt
Q’ty
1
1/1
1
1/1
1
1
2
2
Service points
Reverse the removal steps for installation.
4-8
FUEL
FUEL TANK
E
SERVICE POINTS
A
B
A
B
Check valve inspection
1. Check:
● Check valve
Faulty → Replace.
Checking steps:
● Connect a hose to the end of check
valve “A” and blow into it.
Air should come out from end “B”.
● Connect the hose to the end of check
valve “B” and blow into it.
Air should not come out from end “A”.
Fuel level sensor inspection
Refer to “INDICATION SYSTEM” in
chapter 7.
Fuel tank inspection
1. Inspect:
● Fuel tank
Cracks/damage → Replace.
Pipe joint inspection
1. Inspect:
● Pipe
Contaminants → Clean.
Bends/damage → Replace.
4-9
FUEL
INTAKE SILENCER
E
INTAKE SILENCER
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
INTAKE SILENCER REMOVAL
Bolt
Intake silencer cover
Bolt
Spark arrester
Intake silencer
O-ring
Q’ty
Service points
Follow the left “Step” for removal.
3
1
4
1
1
2
Reverse the removal steps for installation.
4-10
FUEL
CARBURETOR UNIT
E
CARBURETOR UNIT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Q’ty
1
2
3
4
Procedure/Part name
CARBURETOR REMOVAL
Battery box
Intake silencer
Bolt
Thermoswitch
Clamp/cooling water hose
Grease hose
5
Clamp/cooling water hose
1/1
6
Clamp/cooling water hose
1/1
2
1
1/1
1
4-11
Service points
Follow the left “Step” for removal.
Refer to “BATTERY BOX” in chapter 8.
Refer to “INTAKE SILENCER”.
NOTE:
When removing the carburetor, the
exhaust chamber assembly does not
need to be removed if the engine unit has
already been removed.
Å For cooling water pilot outlet on
starboard side
ı For cooling water pilot outlet on port
side
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
14
15
Procedure/Part name
Hose clamp
Hose clamp
Floatation
Water lock band
Bolt
Bolt
Muffler stay 3
Bolt
Nut/washer
Q’ty
2
2
1
1
1
1
1
4
2/2
4-12
Service points
Slide the outer exhaust joint.
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
Step
16
Procedure/Part name
Muffler stay 1
Q’ty
2
17
18
19
20
21
22
Bolt
Hose clamp
Exhaust chamber assembly
Rubber joint
Outer exhaust joint
Inner exhaust joint
2
2
1
1
1
1
4-13
Service points
NOTE:
Make sure to remove spark plugs before
removing the muffler stay 1.
Slide the water lock to back
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
Step
23
Procedure/Part name
Fuel hose
Q’ty
2
Service points
Å suction
ı return
NOTE:
Use the white marks a on the fuel hoses
to distinguish the hose ends.
24
25
26
27
Oil feed hose
Choke cable
Throttle cable
Oil pump cable
2
1
1
1
4-14
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
Step
28
29
30
31
32
33
Procedure/Part name
Pulse hose
Bolt
Bolt
Carburetor unit
Gasket
Dowel pin
Q’ty
2
2
4
1
1
2
Service points
Not reusable
Reverse the removal steps for installation.
4-15
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Q’ty
1
2
Procedure/Part name
CARBURETOR UNIT
SEPARATION
Pulse hose
Fuel hose
3
4
5
6
Oil feed hose
Accelerator pump fuel hose
Throttle link
Choke link
2
3
1
1
2
4
4-16
Service points
Follow the left “Step” for removal.
Å suction
ı return
FUEL
CARBURETOR UNIT
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
14
Procedure/Part name
Bolt
Cable bracket
Bolt
Carburetor
Gasket
Carburetor joint
Bolt/washer
Fuel hose guide
Q’ty
3
1
4
2
2
1
2/2
1
Service points
Not reusable
Reverse the removal steps for installation.
4-17
FUEL
CARBURETOR UNIT
E
SERVICE POINTS
Throttle valve synchronization inspection
and adjustment
1. Check:
● Throttle valve synchronization
Different clearances → Adjust.
a
Checking steps:
● Loosen the throttle stop screw 1 until
untouched the screw end from the
throttle lever.
● Check the each throttle valve is fully
closed a.
a
2. Adjust:
● Throttle valve synchronization
Adjustment steps:
● Loosen the throttle stop screw 1 until
untouched the screw end from the
throttle lever.
● Loosen the screws 2.
NOTE:
Make sure that the throttle valves are in
the fully closed position.
●
Tighten the screws 2.
T.
Screw:
2 N • m (0.2 kgf • m, 1.4 ft • lb)
R.
●
4-18
Turn in the throttle stop screw to the
original position.
FUEL
CARBURETOR UNIT
E
Choke cable and throttle cable installation
1. Install:
● Choke cable 1
● Throttle cable 2
Choke cable guide installation
position a:
13–15 mm (0.51–0.59 in)
Throttle cable guide installation
position a:
18–20 mm (0.71–0.79 in)
2. Adjust:
● Throttle lever free play
● Choke lever operation
Refer to “CONTROL SYSTEM” in
chapter 3.
Oil pump cable installation
1. Adjust:
● Oil pump cable
Refer to “OIL PUMP”.
Carburetor assembly
1. Adjust:
● Trolling speed
Refer to “FUEL SYSTEM” in chapter 3.
4-19
FUEL
CARBURETOR
E
CARBURETOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
CARBURETOR DISASSEMBLY
Accelerator pump fuel hose
Screw
Accelerator pump/carburetor
cover
Diaphragm
Screw
Regulator body
Gasket
Main jet
Pilot jet
Q’ty
1
4
1/1
1
2
1
1
1
1
4-20
Service points
Follow the left “Step” for disassembly.
Carburetor #1
Carburetor #1/carburetor #2
FUEL
CARBURETOR
E
EXPLODED DIAGRAM
Step
10
11
12
13
14
15
16
17
18
Procedure/Part name
Screw
Arm
Arm pin
Spring
Screw
Needle valve seat holder
Needle valve
Needle valve seat
O-ring
Q’ty
1
1
1
1
1
1
1
1
1
Service points
Reverse the disassembly steps for
assembly.
4-21
FUEL
CARBURETOR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
ACCELERATOR PUMP
DISASSEMBLY
Screw
Stay
Spring
Spring seat
Screw
Accelerator pump cover
Spring
Diaphragm
Accelerator pump body
Q’ty
Service points
Follow the left “Step” for disassembly.
1
1
1
1
4
1
1
1
1
Reverse the disassembly steps for
assembly.
4-22
FUEL
CARBURETOR
E
SERVICE POINTS
NOTE:
Before disassembling the carburetor, make
sure to note the number of times the pilot
screw is turned in from its set position to
the seated position.
CAUTION:
Do not use steel wire for cleaning the jets.
This may enlarge the jet diameters and
seriously affect performance.
Diaphragm inspection
1. Inspect:
● Diaphragm
Damage → Replace.
Accelerator pump body inspection
1. Inspect:
● One way valve
Crack/damage → Replace the accelerator pump body.
● Fuel passage
Clog → Clean or replace.
Arm inspection
1. Inspect:
● Arm 1
Bends/damage → Repair or replace.
2. Measure:
● Arm height a
Arm height:
0–0.2 mm (0–0.008 in)
NOTE:
● Measure the distance between the surface
of the carburetor body b and the top surface of the arm.
● The arm should be resting on the needle
valve, but not compressing it.
4-23
FUEL
CARBURETOR
E
Regulator body inspection
1. Inspect:
● Regulator body
Contaminants → Clean.
Damage → Replace.
● Valve (clear film) 1
Damage → Replace.
Needle valve inspection
1. Inspect:
● Needle valve
● Needle valve seat
Contaminants a → Clean.
Wear b → Replace.
NOTE:
Always replace the needle valve and needle
valve seat as a set.
Jet and carburetor body inspection
1. Inspect:
● Main jet
● Pilot jet
● Carburetor body
Clog/contaminants → Clean.
Damage/wear → Replace.
CAUTION:
Do not use a steel wire to clean the jets.
This may enlarge the jet diameters and
seriously affect performance.
Carburetor assembly
NOTE:
Before assembling the carburetor, make
sure to turn out the pilot screw the same
number of times, as noted before disassembly, from the seated position to the set position.
1. Adjust:
● Trolling speed
Refer to “FUEL SYSTEM” in chapter 3.
4-24
FUEL
FUEL PUMP
E
FUEL PUMP
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
FUEL PUMP DISASSEMBLY
Carburetors
Screw
Fuel pump cover
Gasket
Diaphragm
O-ring
Diaphragm body
Q’ty
4
1
1
1
1
1
4-25
Service points
Follow the left “Step” for disassembly.
Refer to “CARBURETOR UNIT”.
Not reusable
FUEL
FUEL PUMP
E
EXPLODED DIAGRAM
Step
7
8
9
10
Procedure/Part name
Rubber diaphragm
Diaphragm
Packing
Fuel filter
Q’ty
1
1
1
1
Service points
Reverse the disassembly steps for
assembly.
4-26
FUEL
FUEL PUMP
E
SERVICE POINTS
Fuel pump inspection
1. Inspect:
● Diaphragm
● Rubber diaphragm
● Diaphragm body
Damage → Replace.
Fuel filter inspection
1. Inspect:
● Fuel filter
Clog/contaminants → Clean.
Damage → Replace.
4-27
FUEL
OIL PUMP
E
OIL PUMP
EXPLODED DIAGRAM
1
4
5
2
3
LT
572
572
6 × 20 mm
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
Procedure/Part name
OIL PUMP REMOVAL
Exhaust chamber assembly
Oil pump cable and oil feed
hoses
Oil return hose
Oil hose
Bolt
Oil pump assembly
5
Gasket
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “CARBURETOR UNIT”.
Refer to “CARBURETOR UNIT”.
1
1
2
1
NOTE:
When removing the oil pump, the exhaust
chamber assembly does not need to be
removed if the engine unit has already
been removed.
1
Not reusable
Reverse the removal steps for installation.
4-28
FUEL
OIL PUMP
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
OIL PUMP HOSES AND CABLE
REMOVAL
Air bleed screw
Gasket
Oil feed hose 1
Check valve
Oil feed hose 2
Hose joint
Oil return hose
Oil pump cable
Oil pump
Q’ty
Service points
Follow the left “Step” for removal.
1
1
2
2
2
1
2
1
1
Reverse the removal steps for installation.
4-29
FUEL
OIL PUMP
E
SERVICE POINTS
Oil pump inspection
1. Inspect:
● Oil pump
Contaminants → Clean.
Damage/wear → Replace.
● Oil pump joint piece
Damage/wear → Replace.
Oil hose inspection
1. Inspect:
● Oil hose
Cracks/damage → Replace.
CAUTION:
If the oil feed hoses are not full of oil, fill
them up.
Check valve inspection
1. Check:
● Check valve
Faulty → Replace.
Checking steps:
Connect a hose to the end of check
valve “A” and blow into it.
Air should come out from end “B”.
● Connect the hose to the end of check
valve “B” and blow into it.
Air should not come out from end “A”.
●
Oil pump cable adjustment
1. Check:
● Oil pump lever position
Incorrect → Adjust.
Checking steps:
● Fully close the carburetor throttle
valves.
● Check that the mark a on the oil pump
lever is aligned with the mark b on the
oil pump body.
4-30
FUEL
OIL PUMP
E
2. Adjust:
● Oil pump cable
Adjustment steps:
Loosen the locknut 1 and the adjusting nut 2.
● Fully close the carburetor throttle
valves.
● Adjust the oil pump cable so that the
mark a on the oil pump lever is
aligned with the mark b on the oil
pump body.
● Tighten the adjusting nut and locknut.
●
1
2
Oil injection pump air bleeding
1. Bleed:
● Air
Air bleeding steps:
Place rags around the air bleed screw
1 to catch any oil that might spill.
● Fill the oil tank with the recommended
oil.
1
●
NOTE:
If the oil pump is replaced or the oil suction hose is removed, bleed air from the
oil suction hose by removing it from the
oil pump.
After bleeding the air, reconnect the
hose with a locking tie.
Recommended engine oil:
YAMALUBE 2-W or an
equivalent TC-W3 certified
outboard oil
●
●
●
4-31
Loosen the air bleed screw 1 two full
turns and make sure that both the oil
and air bubbles flow out.
When there are no air bubbles left,
tighten the air bleed screw.
Wipe up any spilt oil.
FUEL
OIL PUMP
E
T.
Air bleed screw:
5 N • m (0.5 kgf • m, 3.6 ft • lb)
R.
CAUTION:
Do not run the engine if oil does not
flow out of the air bleed screw. Inspect
the oil pump hoses for proper routing
and make sure there are no restrictions
in the line.
4-32
POWR
E
CHAPTER 5
POWER UNIT
ENGINE UNIT ................................................................................................. 5-1
EXPLODED DIAGRAM ............................................................................. 5-1
REMOVAL AND INSTALLATION CHART ............................................... 5-1
SERVICE POINTS ..................................................................................... 5-5
Shim removal .................................................................................... 5-5
Engine mount inspection ................................................................. 5-5
Coupling clearance inspection......................................................... 5-5
EXHAUST CHAMBER ASSEMBLY................................................................ 5-6
EXPLODED DIAGRAM ............................................................................. 5-6
REMOVAL AND INSTALLATION CHART ............................................... 5-6
EXHAUST CHAMBER JOINT....................................................................... 5-10
EXPLODED DIAGRAM ........................................................................... 5-10
REMOVAL AND INSTALLATION CHART ............................................. 5-10
EXHAUST MANIFOLD ................................................................................. 5-12
EXPLODED DIAGRAM ........................................................................... 5-12
REMOVAL AND INSTALLATION CHART ............................................. 5-12
REED VALVES .............................................................................................. 5-13
EXPLODED DIAGRAM ........................................................................... 5-13
REMOVAL AND INSTALLATION CHART ............................................. 5-13
SERVICE POINTS ................................................................................... 5-14
Reed valve inspection..................................................................... 5-14
YPVS ............................................................................................................. 5-15
EXPLODED DIAGRAM ........................................................................... 5-15
REMOVAL AND INSTALLATION CHART ............................................. 5-15
SERVICE POINTS ................................................................................... 5-17
YPVS valve inspection .................................................................... 5-17
YPVS valve installation................................................................... 5-17
CYLINDER HEAD .......................................................................................... 5-18
EXPLODED DIAGRAM ........................................................................... 5-18
REMOVAL AND INSTALLATION CHART ............................................ 5-18
SERVICE POINTS ................................................................................... 5-19
Cylinder head inspection................................................................ 5-19
POWR
CYLINDERS................................................................................................... 5-20
EXPLODED DIAGRAM ........................................................................... 5-20
REMOVAL AND INSTALLATION CHART ............................................. 5-20
SERVICE POINTS ................................................................................... 5-21
Cylinder inspection ......................................................................... 5-21
PISTONS ....................................................................................................... 5-22
EXPLODED DIAGRAM ........................................................................... 5-22
REMOVAL AND INSTALLATION CHART ............................................. 5-22
SERVICE POINTS ................................................................................... 5-24
Piston pin clip removal and installation........................................ 5-24
Piston inspection............................................................................. 5-24
Cylinder and piston combination .................................................. 5-25
Piston ring inspection ..................................................................... 5-25
Piston pin and bearing inspection ................................................. 5-26
STARTER MOTOR ........................................................................................ 5-28
EXPLODED DIAGRAM ........................................................................... 5-28
REMOVAL AND INSTALLATION CHART ............................................ 5-28
FLYWHEEL MAGNETO ................................................................................ 5-29
EXPLODED DIAGRAM ........................................................................... 5-29
REMOVAL AND INSTALLATION CHART ............................................. 5-29
SERVICE POINTS ................................................................................... 5-34
Drive coupling removal and installation ....................................... 5-34
Flywheel magneto removal and installation ................................ 5-34
Drive coupling inspection............................................................... 5-35
Flywheel magneto inspection ........................................................ 5-35
Starter clutch assembly inspection ............................................... 5-35
CRANKCASE................................................................................................. 5-36
EXPLODED DIAGRAM ........................................................................... 5-36
REMOVAL AND INSTALLATION CHART ............................................. 5-36
SERVICE POINTS ................................................................................... 5-38
Crankcase inspection ...................................................................... 5-38
Crankcase installation..................................................................... 5-38
CRANKSHAFT............................................................................................... 5-39
EXPLODED DIAGRAM ........................................................................... 5-39
REMOVAL AND INSTALLATION CHART ............................................. 5-39
SERVICE POINTS ................................................................................... 5-40
Crankshaft inspection ..................................................................... 5-40
E
1
2
3
4
5
6
7
8
9
POWR
ENGINE UNIT
E
ENGINE UNIT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
Procedure/Part name
ENGINE UNIT REMOVAL
Battery box
YPVS cables and YPVS
servomotor
Intake silencer
Choke cable, throttle cable and
fuel hoses
Coupler
Band
Clamp/Cooling water hose
Q’ty
3
6
1
5-1
Service points
Follow the left “Step” for removal.
Refer to “BATTERY BOX” in chapter 8.
Refer to “YPVS SERVOMOTOR” in
chapter 7.
Refer to “INTAKE SILENCER” in
chapter 4.
Refer to “CARBURETOR UNIT” in
chapter 4.
POWR
ENGINE UNIT
E
EXPLODED DIAGRAM
Step
4
5
6
Procedure/Part name
Grease hose
Clamp/cooling water hose
Clamp/cooling water hose
Q’ty
1
1/1
1/1
7
Clamp/cooling water hose
1/1
8
9
Oil hose
Oil return hose
1
1
5-2
Service points
Å For cooling water pilot outlet on
starboard side
ı For cooling water pilot outlet on port
side
POWR
ENGINE UNIT
E
EXPLODED DIAGRAM
Step
10
11
12
13
14
15
Procedure/Part name
Bolt/collar
Coupling cover
Floatation
Water lock band
Hose clamp
Bolt/washer
Q’ty
1/1
1
1
1
2
4/4
5-3
Service points
NOTE:
● Before removing the engine unit, fix the
choke valves to the choke link with a
plastic band, etc. to the fully closed
position.
● When lifting the engine unit, hook the
hoister on the bow side of muffler stay
1.
● Lift the engine unit carefully trying not
hit it on the deck.
POWR
ENGINE UNIT
E
EXPLODED DIAGRAM
Step
16
17
18
Procedure/Part name
Shim
Engine unit
Rubber joint
Q’ty
*
1
1
*: As required
5-4
Service points
Slide the water lock to back.
Reverse the removal steps for installation.
POWR
ENGINE UNIT
E
SERVICE POINTS
Shim removal
1. Remove:
● Shims
NOTE:
To ease reassembly and coupling alignment, remove the shims and organize them
in their respective groups (e.g., front right,
rear left) prior to removing the mounting
bolts.
Engine mount inspection
1. Inspect:
● Engine mounts
Cracks/damage → Replace.
Coupling clearance inspection
1. Measure:
● Clearance a
● Clearance b
(with the rubber damper)
Out of specification → Adjust.
NOTE:
Measure the clearances with a straightedge
and thickness gauge.
Clearance a:
0–0.5 mm (0–0.020 in)
Clearance b:
2–4 mm (0.079–0.157 in)
2. Adjust:
● Clearance a and b
Adjustment steps:
● Adjust the clearance a by adding or
removing shims.
● Adjust the clearance b by moving the
engine unit position.
5-5
POWR
EXHAUST CHAMBER ASSEMBLY
EXHAUST CHAMBER ASSEMBLY
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
EXHAUST CHAMBER
ASSEMBLY REMOVAL
Engine unit
Bolt
Thermoswitch
Hose clamp
Hose clamp
Bolt
Bolt
Muffler stay 3
Bolt
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT”.
2
1
2
2
1
1
1
4
5-6
Slide the outer exhaust joint.
E
POWR
EXHAUST CHAMBER ASSEMBLY
E
EXPLODED DIAGRAM
Step
9
10
Procedure/Part name
Nut/washer
Muffler stay 1
Q’ty
2/2
2
11
12
13
14
Bolt
Exhaust chamber assembly
Outer exhaust joint
Inner exhaust joint
2
1
1
1
Service points
NOTE:
Make sure to remove spark plugs before
removing the muffler stay 1.
Reverse the removal steps for installation.
5-7
POWR
EXHAUST CHAMBER ASSEMBLY
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
EXHAUST CHAMBER
DISASSEMBLY
Nut/washer
Bolt
Nut/washer
Exhaust chamber
Gasket
Pin
Q’ty
1/1
3
2/2
1
1
2
5-8
Service points
Follow the left “Step” for disassembly.
Not reusable
POWR
EXHAUST CHAMBER ASSEMBLY
E
EXPLODED DIAGRAM
Step
7
8
9
10
Procedure/Part name
Muffler
Screw
Plate
Gasket
Q’ty
1
3
1
1
5-9
Service points
Not reusable
Reverse the disassembly steps for
assembly.
POWR
EXHAUST CHAMBER JOINT
EXHAUST CHAMBER JOINT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
EXHAUST CHAMBER JOINT
REMOVAL
Exhaust chamber assembly
Q’ty
Clamp/cooling water hose
Bolt
Bolt
Muffler stay
Bolt
2/1
2
1
1
1
5-10
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER
ASSEMBLY”.
a white mark
E
POWR
EXHAUST CHAMBER JOINT
E
EXPLODED DIAGRAM
Step
6
7
8
9
10
Procedure/Part name
Bolt
Bolt
Exhaust chamber joint
Gasket
Pin
Q’ty
2
2
1
1
2
Service points
Not reusable
Reverse the removal steps for installation.
5-11
POWR
EXHAUST MANIFOLD
E
EXHAUST MANIFOLD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
EXHAUST MANIFOLD REMOVAL
Exhaust chamber joint
Bolt
Bolt
Wire harness bracket
Exhaust manifold
Gasket
Pin
Clamp/cooling water hose
Q’ty
4
4
2
1
1
2
2/2
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST CHAMBER JOINT”.
Not reusable
Reverse the removal steps for installation.
5-12
POWR
REED VALVES
E
REED VALVES
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
REED VALVE REMOVAL
Carburetor unit
Bolt
Reed valve plate
Reed valve assembly
Screw
Valve stopper
Reed valve
Q’ty
12
1
2
16
4
4
Service points
Follow the left “Step” for removal.
Refer to “CARBURETOR UNIT” in
chapter 4.
NOTE:
Tighten the bolts in the proper sequence
as shown.
Reverse the removal steps for installation.
5-13
POWR
REED VALVES
E
SERVICE POINTS
Reed valve inspection
1. Inspect:
● Reed valves
Cracks/damage → Replace.
2. Measure:
● Valve bending a
Out of specification → Replace.
Max. valve bending:
0.2 mm (0.01 in)
3. Measure:
● Valve stopper height b
Out of specification → Adjust or
replace.
Valve stopper height:
10.8–11.4 mm (0.43–0.45 in)
5-14
POWR
YPVS
E
YPVS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
YPVS REMOVAL
Exhaust manifold
Bolt
YPVS valve cover
Gasket
Spacer
Link joint/cover
Circlip
Washer
Q’ty
8
2
2
1
1/1
3
3
5-15
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST MANIFOLD”.
Not reusable
Not reusable
POWR
YPVS
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
Procedure/Part name
Bolt
Shaft 2
Shaft 1
YPVS valve lever
Bolt
YPVS valve assembly
Oil seal
Q’ty
2
1
1
2
2
2
4
Service points
NOTE:
During installation, align the hole a in
the YPVS shaft with the bolt.
NOTE:
If the YPVS shaft is removed, the oil seal
must be replaced.
Reverse the removal steps for installation.
5-16
POWR
YPVS
E
SERVICE POINTS
YPVS valve inspection
1. Eliminate:
● Carbon deposits
(with a rounded scraper 1)
CAUTION:
Do not use a sharp instrument to avoid
damaging or scratching the surfaces.
2. Inspect:
● YPVS valve assembly
Crack/damage/wear → Replace.
YPVS valve installation
1. Install:
● Oil seal
Distance a:
1.0–1.5 mm (0.04–0.06 in)
5-17
POWR
CYLINDER HEAD
E
CYLINDER HEAD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
Procedure/Part name
CYLINDER HEAD REMOVAL
Exhaust manifold
Bolt
2
3
Cylinder head
Gasket
Q’ty
10
1
1
5-18
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST MANIFOLD”.
NOTE:
Tighten the bolts in the proper sequence
as shown and in two stages.
Not reusable
Reverse the removal steps for installation.
POWR
CYLINDER HEAD
E
SERVICE POINTS
Cylinder head inspection
1. Eliminate:
● Carbon deposits
(with a rounded scraper 1)
CAUTION:
Do not use a sharp instrument to avoid
damaging or scratching the cylinder head
or spark plug bore threads.
2. Inspect:
● Cylinder head water jacket
Corrosion/mineral deposits → Clean
or replace.
3. Measure:
● Cylinder head warpage
(with a straightedge and thickness
gauge)
Out of specification/score marks →
Resurface.
Warpage limit:
0.1 mm (0.004 in)
NOTE:
Place a 400–600 grit wet sandpaper on a
surface plate and resurface the cylinder
head using a figure-eight sanding pattern.
5-19
POWR
CYLINDERS
E
CYLINDERS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
Procedure/Part name
CYLINDER REMOVAL
YPVS
Cylinder head
Bolt
Q’ty
2
Cylinder
2
NOTE:
Install the original position.
3
4
Cylinder gasket
Pin
2
4
Not reusable
8
Service points
Follow the left “Step” for removal.
Refer to “YPVS”.
Refer to “CYLINDER HEAD”.
NOTE:
Tighten the bolts in a crisscross pattern
and in two stages.
Reverse the removal steps for installation.
5-20
POWR
CYLINDERS
E
SERVICE POINTS
Cylinder inspection
1. Eliminate:
● Carbon deposits
(with a rounded scraper 1)
2. Inspect:
● Cylinder water jacket
Corrosion/mineral deposits → Clean
or replace.
● Cylinder inner surface
Score marks → Replace.
3. Measure:
● Cylinder bore “D”
(with a cylinder gauge)
Out of specification → Replace cylinder and piston as a set.
NOTE:
Measure the cylinder bore in parallel and at
a right angle to the crankshaft. Then, average the measurements.
Standard
Cylinder
bore “D”
Limit
80.000–
Original cylinder
80.018 mm
bore + 0.04 mm
(3.1496–
(0.0016 in)
3.1503 in)
Taper “T”
—
0.08 mm
(0.003 in)
Out of
round “R”
—
0.05 mm
(0.002 in)
D = Maximum (D1–D6)
T = (Maximum D1 or D2) – (Maximum D5
or D6)
R = (Maximum D1, D3 or D5) – (Minimum
D2, D4 or D6)
5-21
POWR
PISTONS
E
PISTONS
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
Procedure/Part name
PISTON REMOVAL
Cylinders
Piston pin clip
Q’ty
2
Service points
Follow the left “Step” for removal.
Refer to “CYLINDERS”.
CAUTION:
Do not align the open end of the clip
with the piston pin slot a.
2
3
4
Piston pin
Piston
Washer
1
1
2
5-22
NOTE:
Make sure that the arrow b faces
towards the exhaust side.
POWR
PISTONS
E
EXPLODED DIAGRAM
Step
5
6
Procedure/Part name
Bearing
Piston ring
Q’ty
1
2
Service points
CAUTION:
Align each end gap with its respective
locating pin.
Reverse the removal steps for installation.
5-23
POWR
PISTONS
E
SERVICE POINTS
Piston pin clip removal and installation
1. Remove and install:
● Piston pin clip
NOTE:
Before removing or installing the piston pin
clip, cover the crankcase opening with a
clean rag to prevent the piston pin clip from
falling into the crankcase.
Piston inspection
1. Eliminate:
● Carbon deposits
(from the piston crown and piston
ring grooves)
2. Inspect:
● Piston wall
Score marks → Repair with 600–800
grit wet sandpaper or replace.
NOTE:
Lightly sand the piston wall in a crisscross
pattern.
3. Measure:
● Piston skirt diameter
(with a micrometer)
Out of specification → Replace.
Piston diameter
79.899–79.914 mm
(3.1456–3.1462 in)
5-24
Distance a
22 mm
(0.87 in)
POWR
PISTONS
E
4. Calculate:
● Piston-to-cylinder clearance
Out of specification → Replace the
piston, piston rings and cylinder as a
set.
PISTON
CYLINDER
PISTON
=
–
DIAMETER
CLEARANCE
BORE
Piston-to-cylinder clearance:
0.100–0.105 mm
(0.0039–0.0041 in)
Cylinder and piston combination
Select the appropriate piston to match the
cylinder size by the table as follows.
Cylinder size
indication a
Piston color mark
0–5
Red
6–10
Orange
11–15
Green
16–18
Purple
NOTE:
New cylinder bore size = 80.000 + a/1,000
Example: a = 12 → 80.012 mm.
Piston ring inspection
1. Measure:
● Side clearance
(with a thickness gauge 1)
Out of specification → Replace the
piston and piston rings as a set.
Side clearance:
0.03–0.05 mm (0.001–0.002 in)
5-25
POWR
PISTONS
E
2. Measure:
● End gap
(with a thickness gauge 1)
Out of specification → Replace the
piston rings as a set.
End gap:
0.30–0.45 mm (0.012–0.018 in)
NOTE:
Push the piston ring into the cylinder with
the piston crown.
Piston pin and bearing inspection
1. Inspect:
● Piston pins
● Bearings
Signs of heat discoloration → Replace.
2. Measure:
● Piston pin outside diameter
(with a micrometer 1)
Out of specification → Replace.
Piston pin outside diameter:
Standard:
21.995–22.000 mm
(0.8659–0.8661 in)
Limit:
21.990 mm (0.8657 in)
3. Check:
● Piston pin-to-piston free play
(with the piston pin in the piston as
shown)
Free play → Replace the piston pin,
piston or both.
5-26
POWR
PISTONS
E
4. Check:
● Piston pin-to-small end bearing-toconnecting rod free play
(at the small end of the connecting
rod as shown)
Free play/small end wear → Replace
the piston pin, connecting rod, or
small end bearing.
5-27
POWR
STARTER MOTOR
E
STARTER MOTOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
STARTER MOTOR REMOVAL
Engine unit
Nut/washer
Starter motor lead
Bolt
Battery negative lead
Starter motor
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT”.
1/1
1
2
1
1
Reverse the removal steps for installation.
5-28
POWR
FLYWHEEL MAGNETO
E
FLYWHEEL MAGNETO
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
FLYWHEEL MAGNETO
REMOVAL
Engine unit
Oil pump
Bolt
Bolt
Generator cover
Packing
Pin
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT”.
Refer to “OIL PUMP” in chapter 4.
2
6
1
1
2
5-29
POWR
FLYWHEEL MAGNETO
E
EXPLODED DIAGRAM
Step
6
7
8
9
10
Procedure/Part name
Drive coupling
Bolt
Flywheel magneto
Woodruff key
Starter clutch assembly
Q’ty
1
1
1
1
1
Service points
Reverse the removal steps for installation.
5-30
POWR
FLYWHEEL MAGNETO
E
EXPLODED DIAGRAM
14 N • m (1.4 kgf • m, 10 ft • Ib)
6 × 14 mm
4
3
7
LT
8
242
1
2
LT
5
242
6
14 N • m (1.4 kgf • m, 10 ft • Ib)
6 × 30 mm
LT
242
5 N • m (0.5 kgf • m, 3.6 ft • Ib)
5 × 14 mm
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
GENERATOR COVER
DISASSEMBLY
Bolt
Stator coil
Bolt
Cable holder
Bolt/washer
Bolt
Pickup coil
Generator cover
Q’ty
3
1
2
1
1/1
1
1
1
Service points
Follow the left “Step” for disassembly.
NOTE:
This washer holds the pickup coil lead.
Make sure to not pinch the lead between
the projection and the washer when
installing the bolt.
Reverse the disassembly steps for
assembly.
5-31
POWR
FLYWHEEL MAGNETO
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
STARTER CLUTCH
DISASSEMBLY
Clip
Clip stopper
Spring seat
Spring
Washer
Idle gear
Circlip
Q’ty
1
1
1
1
1
1
1
5-32
Service points
Follow the left “Step” for disassembly.
Not reusable
POWR
FLYWHEEL MAGNETO
E
EXPLODED DIAGRAM
Step
8
9
10
Procedure/Part name
Plate
Weight
Spring ring
Q’ty
1
3
1
11
Pinion gear
1
Service points
NOTE:
Install the spring ring after installing the
weights, plate and circlip.
Reverse the disassembly steps for
assembly.
5-33
POWR
FLYWHEEL MAGNETO
E
SERVICE POINTS
Drive coupling removal and installation
1. Remove:
● Drive coupling
Coupler wrench:
YW-06551/90890-06551
Flywheel holder:
YW-06550/90890-06550
NOTE:
Install the drive coupling with the same
special tools that were used for removal.
Flywheel magneto removal and installation
1. Remove:
● Flywheel magneto bolt
Flywheel holder:
YW-06550/90890-06550
NOTE:
Install the bolt with the same special tool
that was used for removal.
Å
2. Remove:
● Flywheel magneto
Flywheel puller:
YB-06117/90890-06521
Set bolt:
M8 × 60 mm
Å For USA and Canada
ı For worldwide
ı
CAUTION:
To prevent damage to the engine or tools,
screw in the flywheel puller set bolts
evenly and completely so that the puller
plate is parallel to the flywheel magneto.
5-34
POWR
FLYWHEEL MAGNETO
Drive coupling inspection
1. Inspect:
● Drive coupling
Damage/wear → Replace.
Flywheel magneto inspection
1. Inspect:
● Ring gear
Damage/wear → Replace.
Starter clutch assembly inspection
1. Inspect:
● Pinion gear 1
● Idle gear 2
Damage/wear → Replace.
2. Check:
● Gear movement
Rough movement → Replace the
defective part(s).
5-35
E
POWR
CRANKCASE
E
CRANKCASE
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
CRANKCASE DISASSEMBLY
Pistons
Starter motor
Generator cover
Bolt
Mount bracket 1
Pin
Bolt
Pin
Mount bracket 2
Bolt
Q’ty
3
1
2
3
2
1
4
5-36
Service points
Follow the left “Step” for disassembly.
Refer to “PISTONS”.
Refer to “STARTER MOTOR”.
Refer to “FLYWHEEL MAGNETO”.
POWR
CRANKCASE
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
15
Procedure/Part name
Bolt
Bolt
Bolt
Bolt
Lower crankcase
Pin
Crankshaft assembly
Upper crankcase
Q’ty
3
1
10
2
1
2
1
1
Service points
NOTE:
Tighten the bolts in sequence as shown.
Reverse the disassembly steps for
assembly.
5-37
POWR
CRANKCASE
E
SERVICE POINTS
Crankcase inspection
1. Inspect:
● Mating surfaces
Scratches → Replace the crankcase.
● Crankcase
Cracks/damage → Replace.
Crankcase installation
1. Apply:
● Gasket Maker®
(onto the crankcase mating surfaces)
NOTE:
Before applying Gasket Maker®, clean the
crankcase mating surfaces.
2. Check:
● Crankshaft
Rough movement → Recheck.
NOTE:
Make sure that the crankshaft rotates
smoothly after installing it.
5-38
POWR
CRANKSHAFT
E
CRANKSHAFT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
CRANKSHAFT REMOVAL
Crankcase
Oil seal
Bearing
Oil seal
Bearing clip
Bearing
Crankshaft
Q’ty
1
1
2
1
1
1
Service points
Follow the left “Step” for removal.
Refer to “CRANKCASE”.
CAUTION:
Install the bearing locating pins into the
grooves in the crankcase body.
Reverse the removal steps for installation.
5-39
POWR
CRANKSHAFT
E
SERVICE POINTS
Crankshaft inspection
1. Measure:
● Crank width A
Out of specification → Replace.
Crank width:
72.95–73.00 mm (2.872–2.874 in)
2. Measure:
● Deflection B
(with a dial gauge)
Out of specification → Replace.
Max. deflection:
0.05 mm (0.002 in)
3. Measure:
● Big end side clearance C
(with a thickness gauge)
Out of specification → Replace.
Big end side clearance:
0.25–0.75 mm (0.010–0.030 in)
4. Measure:
● Small end free play D
(with a dial gauge)
Out of specification → Replace.
Small end free play:
2.0 mm (0.08 in)
5-40
POWR
CRANKSHAFT
E
5. Inspect:
● Bearings
Damage/pitting → Replace.
NOTE:
● Before
inspection, thoroughly clean the
bearings.
● Immediately after inspection, lubricate the
bearings to prevent rust.
6. Inspect:
● Oil seals
Damage/wear → Replace.
5-41
JET
PUMP
E
CHAPTER 6
JET PUMP UNIT
JET PUMP UNIT ............................................................................................. 6-1
EXPLODED DIAGRAM ............................................................................. 6-1
REMOVAL AND INSTALLATION CHART ............................................... 6-1
NOZZLE DEFLECTOR AND NOZZLE RING................................................... 6-4
EXPLODED DIAGRAM ............................................................................. 6-4
REMOVAL AND INSTALLATION CHART ............................................... 6-4
IMPELLER DUCT, IMPELLER HOUSING, AND INTAKE DUCT.................... 6-5
EXPLODED DIAGRAM ............................................................................. 6-5
REMOVAL AND INSTALLATION CHART ............................................... 6-5
IMPELLER DUCT AND DRIVE SHAFT........................................................... 6-7
EXPLODED DIAGRAM ............................................................................. 6-7
REMOVAL AND INSTALLATION CHART ............................................... 6-7
SERVICE POINTS ..................................................................................... 6-9
Drive shaft removal........................................................................... 6-9
Impeller inspection ......................................................................... 6-10
Drive shaft inspection ..................................................................... 6-10
Drive shaft installation.................................................................... 6-10
TRANSOM PLATE AND HOSES.................................................................. 6-13
EXPLODED DIAGRAM ........................................................................... 6-13
REMOVAL AND INSTALLATION CHART ............................................. 6-13
SERVICE POINTS ................................................................................... 6-15
Bilge strainer inspection................................................................. 6-15
Bilge hose inspection...................................................................... 6-15
BEARING HOUSING..................................................................................... 6-16
EXPLODED DIAGRAM ........................................................................... 6-16
REMOVAL AND INSTALLATION CHART ............................................. 6-16
SERVICE POINTS ................................................................................... 6-19
Driven coupling removal and installation..................................... 6-19
Intermediate drive shaft removal .................................................. 6-19
Bearing removal.............................................................................. 6-19
Bearing, driven coupling shaft, and grease hose inspection ...... 6-20
Driven coupling inspection ............................................................ 6-20
Bearing installation ......................................................................... 6-20
Oil seal installation.......................................................................... 6-20
Intermediate housing installation.................................................. 6-21
1
2
3
4
5
6
7
8
9
JET
PUMP
JET PUMP UNIT
E
JET PUMP UNIT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
JET PUMP UNIT REMOVAL
Bolt
Bolt
Intake grate
Bolt
Intake duct
Screw
Speed sensor
Q’ty
2
2
1
4
1
4
1
6-1
Service points
Follow the left “Step” for removal.
NOTE:
Route the speed sensor lead between the
jet pump unit and the bilge hose.
JET
PUMP
JET PUMP UNIT
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
15
16
Procedure/Part name
Bolt
Ride plate
QSTS cable joint
Bilge hose
Nut/washer
Steering cable joint
Clamp/spout hose
Bolt
Bolt
Q’ty
4
1
1
1
1/2
1
1/1
1
4
6-2
Service points
JET
PUMP
JET PUMP UNIT
E
EXPLODED DIAGRAM
Step
17
18
Procedure/Part name
Jet pump unit assembly
Dowel pin
Q’ty
1
2
Service points
NOTE:
● Pull the jet pump unit straight back.
● When installing the jet pump unit, align
the drive shaft spline (male) with the
intermediate drive shaft spline (female).
Reverse the removal steps for installation.
6-3
JET
PUMP
NOZZLE DEFLECTOR AND NOZZLE RING
E
NOZZLE DEFLECTOR AND NOZZLE RING
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
NOZZLE DEFLECTOR AND
NOZZLE RING REMOVAL
Jet pump unit
Bolt
Collar
Nozzle deflector
Bolt
Collar
Nozzle ring
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “JET PUMP UNIT”.
2
2
1
2
2
1
Reverse the removal steps for installation.
6-4
JET
PUMP
IMPELLER DUCT, IMPELLER HOUSING,
AND INTAKE DUCT
E
IMPELLER DUCT, IMPELLER HOUSING, AND INTAKE DUCT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
IMPELLER DUCT AND IMPELLER
HOUSING REMOVAL
Nozzle ring
Bolt
Nozzle
Pin
Impeller duct assembly
Impeller housing
Pin
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “NOZZLE DEFLECTOR AND
NOZZLE RING”.
4
1
2
1
1
2
6-5
NOTE:
Clean the matching surfaces before
applying the Gasket Maker®.
JET
PUMP
IMPELLER DUCT, IMPELLER HOUSING,
AND INTAKE DUCT
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
Procedure/Part name
Bolt
Water inlet cover
Packing
Water inlet strainer
Packing
Q’ty
4
1
1
1
1
Service points
Reverse the removal steps for installation.
6-6
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
E
IMPELLER DUCT AND DRIVE SHAFT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
*1:
Procedure/Part name
IMPELLER DUCT AND DRIVE
SHAFT DISASSEMBLY
Impeller
Spacer
Bolt
Cap
O-ring
Nut
Washer
Q’ty
1
1
3
1
1
1
1
EPNOC grease AP #0
6-7
Service points
Follow the left “Step” for disassembly.
Left-hand threads
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
*1:
Procedure/Part name
Drive shaft
Rear bearing
Spacer
Front bearing
Oil seal
Oil seal
Q’ty
1
1
1
1
1
1
EPNOC grease AP #0
6-8
Service points
Not reusable
Not reusable
Not reusable
Not reusable
Reverse the disassembly steps for
assembly.
E
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
E
SERVICE POINTS
Drive shaft removal
1. Remove:
● Impeller
Drive shaft holder:
YB-06151/90890-06519
NOTE:
The impeller has left-hand threads. Turn the
impeller clockwise to loosen it.
2. Remove:
● Nut 1
Drive shaft holder:
YB-06151/90890-06519
3. Remove:
● Drive shaft 1
NOTE:
Remove the drive shaft with a press.
4. Remove:
● Rear bearing
Å
Slide hammer set:
YB-06096
Stopper guide plate:
90890-06501
Bearing puller:
90890-06535
Bearing puller claw 1:
90890-06536
Stopper guide stand:
90890-06538
ı
Å For USA and Canada
ı For worldwide
6-9
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
5. Remove:
● Front bearing
Driver rod L3:
YB-06071/90890-06652
Needle bearing attachment:
YB-06112/90890-06614
NOTE:
Remove the front bearing with a press.
6. Remove:
● Oil seals
Driver rod L3:
YB-06071/90890-06652
Needle bearing attachment:
YB-06196/90890-06653
NOTE:
Remove the oil seals with press.
Impeller inspection
Refer to “JET PUMP UNIT” in
chapter 3.
Drive shaft inspection
1. Inspect:
● Drive shaft
Damage/wear → Replace.
Drive shaft installation
1. Install:
● Oil seals
Driver rod:
YB-06071/90890-06606
Ball bearing attachment:
YB-06156/90890-06634
6-10
E
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
E
2. Install:
● Front bearing
● Drive shaft
NOTE:
Install the front bearing and drive shaft with
a press.
a
Distance a:
23 ± 0.1 mm (0.91 ± 0.004 in)
3. Install:
● Drive shaft (with front bearing)
● Spacer
● Impeller duct
NOTE:
Press the spacer and the front bearing with
a 36-mm deep socket.
4. Add:
● EPNOC grease AP #0
(between the drive shaft and spacer)
Quantity:
Approximately 1/3 of capacity
5. Install:
● Rear bearing
Bearing inner/outer race
attachment:
YB-34474
NOTE:
● Press the bearing inner/outer race at the
same time holding the drive shaft and
impeller duct.
● If a bearing inner/outer race attachment is
not available, use a washer or pipe with
an outer diameter of 46 mm (1.81 in) and
an inner diameter of 20 mm (0.79 in).
6-11
JET
PUMP
IMPELLER DUCT AND DRIVE SHAFT
E
6. Add:
● EPNOC grease AP #0 (into the cap)
Quantity:
Approximately 1/3 of capacity
7. Install:
● Nut
● Impeller
Drive shaft holder:
YB-06151/90890-06519
6-12
JET
PUMP
TRANSOM PLATE AND HOSES
E
TRANSOM PLATE AND HOSES
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
Procedure/Part name
TRANSOM PLATE AND HOSES
REMOVAL
Exhaust system
Jet pump unit
Hose clamp
Cooling water hose
Bilge hose 1
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “EXHAUST SYSTEM” in
chapter 8.
Refer to “JET PUMP UNIT”.
3
1
1
6-13
Cooling water outlet
NOTE:
Route the bilge hose 1 under the drive
shaft tube.
JET
PUMP
TRANSOM PLATE AND HOSES
E
EXPLODED DIAGRAM
Step
4
5
6
7
8
9
10
Procedure/Part name
Cooling water hose
Nut/washer
Transom plate
Clamp/bilge hose 2
Screw
Bilge strainer holder
Bilge strainer
Q’ty
1
4/4
1
1/1
1
1
1
Service points
Cooling water inlet
Reverse the removal steps for installation.
6-14
JET
PUMP
TRANSOM PLATE AND HOSES
SERVICE POINTS
Bilge strainer inspection
Refer to “JET PUMP UNIT” in
chapter 3.
Bilge hose inspection
1. Inspect:
● Bilge hoses
Cracks/damage/wear → Replace.
6-15
E
JET
PUMP
BEARING HOUSING
E
BEARING HOUSING
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
BEARING HOUSING REMOVAL
Engine unit
Rubber coupling
Bolt
Intermediate housing assembly
Pin
Shim
Q’ty
1
3
1
2
*
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT” in chapter 5.
NOTE:
Install the shims in their original locations.
Reverse the removal steps for installation.
*: As required
6-16
JET
PUMP
BEARING HOUSING
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
BEARING HOUSING
DISASSEMBLY
Grease hose
Nipple
Driven coupling
Washer
Intermediate drive shaft
O-ring
Oil seal
Q’ty
1
1
1
1
1
2
1
6-17
Service points
Follow the left “Step” for disassembly.
Not reusable
JET
PUMP
BEARING HOUSING
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
Procedure/Part name
Oil seal
Oil seal
Circlip
Bearing
Circlip
Q’ty
1
1
1
1
1
Service points
Not reusable
Not reusable
Not reusable
Reverse the disassembly steps for
assembly.
6-18
JET
PUMP
BEARING HOUSING
E
SERVICE POINTS
Driven coupling removal and installation
1. Remove and install:
● Driven coupling
Coupler wrench:
YW-06551/90890-06551
Shaft holder:
YB-06552/90890-06552
NOTE:
Install the driven coupling with the same
special tools that were used for removal.
Intermediate drive shaft removal
1. Remove:
● Intermediate drive shaft
Removal steps:
Temporarily install the driven coupling
to the intermediate drive shaft.
● Insert the long rod to the driven coupling shaft.
● Press out the intermediate drive shaft
by pushing the rod.
1
●
NOTE:
Support the intermediate housing with
steel blocks 1 and press the driven coupling shaft.
Bearing removal
1. Remove:
● Bearing
Driver rod:
YB-06071/90890-06606
Bearing outer race attachment:
YB-06016/90890-06626
NOTE:
● Install the bearing with the same special
tools that were used for removal.
● Support the intermediate housing with
steel blocks 1 and press the bearing.
6-19
JET
PUMP
BEARING HOUSING
E
Bearing, driven coupling shaft, and grease
hose inspection
1. Inspect:
● Bearing
Rotate the inner race by hand.
Damage/rough movement → Replace.
● Intermediate drive shaft
Damage/pitting → Replace.
● Grease hose
Cracks/wear → Replace.
Driven coupling inspection
1. Inspect:
● Driven coupling
● Driven coupling damper
Damage/wear → Replace.
Bearing installation
1. Install:
● Circlip (rear)
2. Install:
● Bearing
Driver rod:
YB-06071/90890-06606
Bearing outer race attachment:
YB-06016/90890-06626
Oil seal installation
1. Install:
● Oil seal
Driver rod:
YB-06071/90890-06606
Bearing outer race attachment:
YB-06016/90890-06626
NOTE:
Before installing the oil seal, lubricate the
clip glove with water resistant grease.
Distance a:
6.8–7.2 mm (0.27–0.28 in)
6-20
JET
PUMP
BEARING HOUSING
E
2. Install:
● Intermediate drive shaft
Distance a:
9.5–10.5 mm (0.37–0.41 in)
NOTE:
Support the intermediate housing with
steel blocks 1 and press the driven coupling shaft.
3. Install:
● Oil seal 1 [8 mm (0.31 in)]
● Oil seal 2 [10 mm (0.39 in)]
Distance a:
10.3–10.7 mm (0.41–0.42 in)
Distance b:
1.6–2.0 mm (0.06–0.08 in)
Intermediate housing installation
1. Install:
● Intermediate housing
● Shim
Installation steps:
Install the intermediate housing.
● Measure the clearance a at each bolt
hole.
● Install the suitable shim from the table
below.
●
Clearance a
Shim thickness
0–0.2 mm
(0–0.008 in)
No need
0.3–0.7 mm
(0.012–0.028 in)
0.5 mm
0.8–1.2 mm
(0.031–0.047 in)
1.0 mm
1.3–2.0 mm
(0.051–0.079 in)
1.5 mm
NOTE:
Install the shim(s) to the original position if
the intermediate housing is not replaced.
6-21
ELEC
–
+
E
CHAPTER 7
ELECTRICAL SYSTEM
ELECTRICAL COMPONENTS......................................................................... 7-1
ELECTRICAL BOX........................................................................................... 7-2
EXPLODED DIAGRAM ............................................................................. 7-2
REMOVAL AND INSTALLATION CHART ............................................... 7-2
ELECTRICAL ANALYSIS ................................................................................ 7-6
INSPECTION............................................................................................. 7-6
Digital tester ...................................................................................... 7-6
Low resistance measurement .......................................................... 7-6
Peak voltage measurement.............................................................. 7-7
Peak voltage adaptor ........................................................................ 7-7
Test harness ..................................................................................... 7-8
IGNITION SYSTEM......................................................................................... 7-9
WIRING DIAGRAM................................................................................... 7-9
IGNITION SPARK GAP........................................................................... 7-10
IGNITION SYSTEM PEAK VOLTAGE.................................................... 7-11
SPARK PLUGS ....................................................................................... 7-12
SPARK PLUG CAPS ............................................................................... 7-12
IGNITION COIL ....................................................................................... 7-12
ENGINE STOP SWITCH ......................................................................... 7-13
THERMOSWITCH................................................................................... 7-13
STARTING SYSTEM..................................................................................... 7-14
WIRING DIAGRAM................................................................................. 7-14
BATTERY ................................................................................................ 7-15
WIRING CONNECTIONS ....................................................................... 7-15
FUSE ....................................................................................................... 7-15
STARTER SWITCH ................................................................................. 7-15
STARTER RELAY.................................................................................... 7-16
STARTER MOTOR ........................................................................................ 7-17
EXPLODED DIAGRAM ........................................................................... 7-17
REMOVAL AND INSTALLATION CHART ............................................ 7-17
SERVICE POINTS ................................................................................... 7-20
Armature inspection ....................................................................... 7-20
Brush holder inspection ................................................................. 7-21
Starter motor front cover inspection............................................. 7-21
ELEC
–
+
CHARGING SYSTEM.................................................................................... 7-22
WIRING DIAGRAM................................................................................. 7-22
FUSE ....................................................................................................... 7-23
BATTERY ................................................................................................ 7-23
RECTIFIER/REGULATOR PEAK VOLTAGE ........................................... 7-23
LIGHTING COIL PEAK VOLTAGE.......................................................... 7-23
YPVS ............................................................................................................. 7-24
WIRING DIAGRAM................................................................................. 7-24
FUSE ....................................................................................................... 7-25
BATTERY ................................................................................................ 7-25
PICKUP COIL .......................................................................................... 7-25
CDI UNIT................................................................................................. 7-25
YPVS SERVOMOTOR .................................................................................. 7-26
EXPLODED DIAGRAM ........................................................................... 7-26
REMOVAL AND INSTALLATION CHART ............................................. 7-26
SERVICE POINTS ................................................................................... 7-27
YPVS cable removal and installation ............................................ 7-27
YPVS cable inspection .................................................................... 7-27
YPVS servomotor inspection ......................................................... 7-27
YPVS cable adjustment .................................................................. 7-28
INDICATION SYSTEM.................................................................................. 7-29
WIRING DIAGRAM................................................................................. 7-29
FUSE ....................................................................................................... 7-30
BATTERY ................................................................................................ 7-30
LIGHTING COIL ...................................................................................... 7-30
RECTIFIER/REGULATOR........................................................................ 7-30
CDI UNIT................................................................................................. 7-30
THERMOSWITCH................................................................................... 7-30
BUZZER .................................................................................................. 7-30
OIL LEVEL SENSOR ............................................................................... 7-30
FUEL LEVEL SENSOR............................................................................ 7-31
MULTIFUNCTION METER ..................................................................... 7-31
Multifunction meter ........................................................................ 7-31
MULTIFUNCTION METER REMOVAL .................................................. 7-31
Display function .............................................................................. 7-32
Fuel level gauge .............................................................................. 7-33
Oil level gauge................................................................................. 7-34
Overheat warning indicator ........................................................... 7-35
Speed meter .................................................................................... 7-36
Speed sensor................................................................................... 7-36
E
1
2
3
4
5
6
7
8
9
ELEC
–
+
ELECTRICAL COMPONENTS
E
ELECTRICAL COMPONENTS
1
C
2
B
3
A
=
4
5
9
8
6
7
1
2
3
4
5
6
7
8
Buzzer
Fuel level sensor
Multifunction meter
YPVS servomotor
Spark plugs
Electrical box
Speed sensor
Battery
Thermoswitch
Starter motor
Stator coil and pickup coil
Engine stop switch, engine stop lanyard
switch and starter switch
C Oil level sensor
9
0
A
B
7-1
ELEC
–
+
ELECTRICAL BOX
E
ELECTRICAL BOX
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
ELECTRICAL BOX DISASSEMBLY
Electrical box
Plastic locking tie
Bolt/collar
Plastic clamp
Bolt
Electrical box cover
Gasket
Q’ty
2
1/1
1
14
1
1
7-2
Service points
Follow the left “Step” for disassembly.
Refer to “BATTERY BOX” in chapter 8.
Not reusable
NOTE:
To separate the battery box from the
engine unit, refer to “ENGINE UNIT”,
“STARTER MOTOR” and “FLYWHEEL
MAGNETO” in Chapter 5 to disconnect
the leads.
ELEC
–
+
ELECTRICAL BOX
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
14
Procedure/Part name
Nut
Starter motor lead/
battery positive lead
Fuse
Plastic locking tie
Screw
Ignition coil
Screw
Starter relay
Q’ty
2
1/1
1
1
2
1
2
1
7-3
Service points
Not reusable
ELEC
–
+
ELECTRICAL BOX
E
EXPLODED DIAGRAM
Step
15
16
17
18
19
20
Procedure/Part name
Bolt
Rectifier/regulator
Thermoswitch
Wire harness
CDI unit
Electrical box housing
Q’ty
1
1
1
2
1
1
Service points
Reverse the disassembly steps for
assembly.
7-4
ELEC
1
2
3
4
5
6
–
+
CDI unit
Starter relay
Fuse (10A)
Ignition coil
Rectifier/regulator
Spark plug caps
ELECTRICAL BOX
B
Br
G
P
R
W
E
: Black
: Brown
: Green
: Pink
: Red
: White
7-5
ELEC
–
+
ELECTRICAL ANALYSIS
E
ELECTRICAL ANALYSIS
INSPECTION
CAUTION:
● All
measuring instruments should be handled with special care. Damaged or mishandled instruments will not measure
properly.
● On an instrument powered by dry batteries, check the battery’s voltage periodically and replace the batteries if
necessary.
Digital tester
NOTE:
Throughout this chapter the digital tester’s
part number has been omitted. Refer to the
following part number.
Digital tester:
J-39299/90890-06752
NOTE:
“
” indicates a continuity of electricity; i.e., a closed circuit at the respective
switch position.
Low resistance measurement
NOTE:
● When measuring a resistance of 10 Ω or
less with the digital tester, the correct
measurement
cannot
be
obtained
because of the tester’s internal resistance.
● To obtain the correct value, subtract the
internal resistance from the displayed
measurement.
● The internal resistance of the tester can be
obtained by connecting both of its terminals.
Correct value =
Displayed measurement –
Internal resistance
7-6
ELEC
–
+
ELECTRICAL ANALYSIS
E
Peak voltage measurement
NOTE:
● When checking the condition of the ignition system it is vital to know the peak
voltage.
● Cranking speed is dependant on many
factors (e.g., fouled or weak spark plugs, a
weak battery). If one of these is defected,
the peak voltage will be lower than specification.
● If the peak voltage measurement is not
within specification the engine will not
operate properly.
● A low peak voltage will also cause components to prematurely wear.
Peak voltage adaptor
NOTE:
● Throughout this chapter the peak voltage
adaptor’s part number has been omitted.
Refer to the following part number.
● The peak voltage adaptor should be used
with the digital tester.
Peak voltage adaptor:
YU-39991/90890-03169
●
Å
When measuring the peak voltage, connect the peak voltage adaptor to the digital tester and switch the selector to the
DC voltage mode.
NOTE:
● Make sure that the adaptor leads are
properly installed in the digital tester.
● Make sure that the positive pin (the “+”
mark facing up as shown) on the adaptor
is installed into the positive terminal of
the tester.
● The test harness is needed for the following tests.
ı
Å Voltage measurement
ı Peak voltage measurement
7-7
ELEC
–
+
ELECTRICAL ANALYSIS
E
Test harness
YW-
90890-
Pin
06779
06779
8
Usage
Charge coil and
pickup coil
Checking steps:
● Disconnect the coupler connections.
● Connect the test harness between the
couplers.
● Connect the tester terminals to the terminals which are being checked.
● Run the engine and observe the measurement.
NOTE:
● Make sure the output lead (red lead) of the
rectifier/regulator is disconnected when
measuring the peak voltage of the lighting
coil and rectifier/regulator.
● If the charge coil and pickup coil are measured unloaded, disconnect the test harness on the output side coupler.
7-8
ELEC
–
+
IGNITION SYSTEM
E
IGNITION SYSTEM
WIRING DIAGRAM
3
L
B
W/B
1
B
Br
O
P
4
5
W
SET
PULL
W
W/R
W/B W/R
2
Br
W/B
B
L
L
W
B
P
O
Br
B
L
W/R O
W
Br W/B P
B
O
O
W
P
W
B
B
W
B
7
8
B
P
B
P
B
6
1
2
3
4
5
6
7
8
Pickup coil
Charge coil
CDI unit
Engine stop switch
Engine stop lanyard switch
Thermoswitch
Ignition coil
Spark plugs
B
Br
L
O
P
R
W
W/B
W/R
7-9
: Black
: Brown
: Blue
: Orange
: Pink
: Red
: White
: White/black
: White/red
B
R
Br
ELEC
–
+
IGNITION SYSTEM
E
IGNITION SPARK GAP
WARNING
● When
checking the spark gap, do not
touch any of the connections of the spark
gap tester lead wires.
● When performing the spark gap test, take
special care not to let sparks leak out of
the removed spark plug cap.
● When performing the spark gap check,
keep flammable gas or liquids away,
since this test can produce sparks.
Å
1. Check:
● Ignition spark gap
Below specification → Check the CDI
unit output peak voltage.
Check the ignition coil for resistance.
Spark gap:
10 mm (0.39 in)
ı
Checking steps:
Connect the spark plug cap to the
spark gap tester.
● Set the spark gap length on the adjusting knob.
●
Spark gap tester:
YM-34487/90890-06754
Å
●
Crank the engine and observe the ignition system spark through the discharge window.
Å For USA and Canada
ı For worldwide
ı
7-10
ELEC
–
+
IGNITION SYSTEM
E
IGNITION SYSTEM PEAK VOLTAGE
WARNING
When checking the electrical components,
do not touch any of the connections of the
digital tester lead wires.
NOTE:
● If there is no spark or the spark is weak,
continue with the ignition system test.
● If a good spark is obtained, the problem is
not with the ignition system, but possibly
with the spark plug(s) or another component.
1. Measure:
● CDI unit output peak voltage
Below specification → Measure the
charge coil output peak voltage or
replace the CDI unit.
CDI unit output peak voltage:
Orange (O) – Black (B)
r/min
V
Unloaded
Loaded
Cranking
85
110
2,000
3,500
205
200
2. Measure:
● Charge coil output peak voltage
Below specification → Replace the
charge coil.
Charge coil output peak voltage:
Brown (Br) – Blue (L)
r/min
V
Unloaded
Loaded
Cranking
90
120
2,000
3,500
220
210
Test harness (8-pin):
YW-06779/90890-06779
7-11
ELEC
–
+
IGNITION SYSTEM
E
3. Measure:
● Pickup coil output peak voltage
Below specification → Replace the
pickup coil.
Pickup coil output peak voltage:
White/red (W/R) –
White/black (W/B)
r/min
V
Unloaded
Loaded
Cranking
5
3
2,000
3,500
7
11
Test harness (8-pin):
YW-06779/90890-06779
SPARK PLUGS
Refer to “POWER UNIT” in chapter 3.
SPARK PLUG CAPS
1. Inspect:
● Spark plug cap
Loose → Tighten.
Cracks/damage → Replace.
IGNITION COIL
1. Measure:
● Primary coil resistance
Out of specification → Replace.
Primary coil resistance:
Orange (O) – Black (B)
0.078–0.106 Ω at 20 ˚C (68 ˚F)
NOTE:
When measuring a resistance of 10 Ω or
less with the digital tester, the correct measurement cannot be obtained because of
the tester’s internal resistance.
Refer to “Low resistance measurement”.
7-12
ELEC
–
+
IGNITION SYSTEM
E
2. Measure:
● Secondary coil resistance
Out of specification → Replace.
Secondary coil resistance:
Spark plug cap – Spark plug cap
14.3–30.5 kΩ at 20 ˚C (68 ˚F)
ENGINE STOP SWITCH
1. Check:
● Engine stop switch continuity
Out of specification → Replace.
Engine stop switch continuity
(black coupler)
Lock plate
Position
Installed
Removed
Lead color
White
Black
Free
Push
Free
Push
THERMOSWITCH
1. Measure:
● Thermoswitch continuity
Out of specification → Replace.
Thermoswitch continuity
temperature:
Pink (P) – Black (B)
a 80 ˚C (177 ˚F)
b 70 ˚C (159 ˚F)
1 No continuity
2 Continuity
Å Temperature
ı Time
Measurement steps:
● Suspend the thermostat in a container
filled with water.
● Place a thermometer in the water.
● Slowly heat the water.
● Measure the continuity when the specified temperature is reached.
7-13
ELEC
–
+
STARTING SYSTEM
E
STARTING SYSTEM
WIRING DIAGRAM
1
R
2
W
M
B
3
R
Br
SET
PULL
Br
B
R
Br
Br
R
Br
R
R
4
Br
R
R
B
R
B
5
1
2
3
4
5
6
6
Starter motor
Engine stop lanyard switch
Starter switch
Fuse (10A)
Starter relay
Battery
B
Br
R
W
7-14
: Black
: Brown
: Red
: White
Br
ELEC
–
+
STARTING SYSTEM
E
BATTERY
Refer to “ELECTRICAL” in chapter 3.
WIRING CONNECTIONS
1. Check:
● Wiring connections
Poor connections → Properly connect.
FUSE
1. Check:
● Fuse holder continuity
No continuity → Check the fuse
holder leads.
2. Check:
● Fuse holder lead continuity
No continuity → Replace the fuse
holder.
Continuity → Check the fuse.
3. Check:
● Fuse broken
Broken → Replace.
Fuse rating:
10A
STARTER SWITCH
1. Check:
● Continuity
Out of specification → Replace.
Starter continuity
(natural coupler)
Lock plate
Installed
Removed
7-15
Position
Free
Push
Free
Push
Leads
Red
Brown
ELEC
–
+
STARTING SYSTEM
E
STARTER RELAY
1. Inspect:
● Brown lead terminal
● Black lead terminal
Loose → Tighten.
2. Check:
● Starter relay
Faulty → Replace.
Checking steps:
Connect the tester leads between the
starter relay terminals as shown.
● Connect the brown lead terminal to
the positive battery terminal.
● Connect the black lead terminal to the
negative battery terminal.
● Check that there is continuity between
the starter relay terminals.
● Check that there is no continuity after
the brown or black lead is removed.
●
7-16
ELEC
–
+
STARTER MOTOR
E
STARTER MOTOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
STARTER MOTOR
DISASSEMBLY
Starter motor
O-ring
Bolt
Starter motor front cover
O-ring
Oil seal retainer
Washer
Shim
Q’ty
1
2
1
1
1
1
*
*: As required
7-17
Service points
Follow the left “Step” for disassembly.
Refer to “STARTER MOTOR”
in chapter 5.
Not reusable
Not reusable
t = 0.2 mm, 0.5 mm
ELEC
–
+
STARTER MOTOR
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
15
16
17
Procedure/Part name
Starter motor rear cover
O-ring
Shim
Armature assembly
Nut/spring washer/washer
O-ring
Brush holder
Brush spring
Bolt
Brush assembly
Q’ty
1
1
*
1
1/1/4
1
1
4
1
1
*: As required
7-18
Service points
Not reusable
t = 0.2 mm, 0.8 mm
Not reusable
ELEC
–
+
STARTER MOTOR
E
EXPLODED DIAGRAM
Step
18
19
20
Procedure/Part name
Spacer
Holder
Starter motor yoke
Q’ty
1
1
1
Service points
Reverse the disassembly steps for
assembly.
7-19
ELEC
–
+
STARTER MOTOR
E
SERVICE POINTS
Armature inspection
1. Inspect:
● Armature shaft 1
Damage/wear → Replace.
1
2. Inspect:
● Commutator
Dirt → Clean with 600 grit sandpaper.
3. Measure:
● Commutator diameter
Out of specification → Replace.
Min. commutator diameter:
27.0 mm (1.06 in)
4. Check:
● Commutator undercut
Contaminants → Clean.
NOTE:
Remove all mica and metal particles with
compressed air.
5. Measure:
● Commutator undercut
Out of specification → Replace.
Min. commutator undercut:
0.2 mm (0.01 in)
7-20
ELEC
–
+
STARTER MOTOR
E
6. Inspect:
● Armature coil continuity
Out of specification → Replace.
Armature coil continuity:
Commutator segments 1 Continuity
Segment - Laminations 2 No continuity
Segment - Armature shaft No continuity
Brush holder inspection
1. Measure:
● Brush length a
Out of specification → Replace.
Min. brush length:
6.5 mm (0.26 in)
2. Check:
● Brush holder continuity
Out of specification → Replace.
Brush holder continuity:
Brush holder - Base
No continuity
Starter motor front cover inspection
1. Inspect:
● Starter motor front cover bushing
Damage/wear → Replace the starter
motor front cover.
7-21
ELEC
–
+
CHARGING SYSTEM
E
CHARGING SYSTEM
WIRING DIAGRAM
1
G
G
M
B
B
G G
R
G G
R
2
3
R
4
R
R
B
1
2
3
4
Lighting coil
Battery
Fuse (10A)
Rectifier/regulator
B
G
R
G/W
7-22
: Black
: Green
: Red
: Green/white
ELEC
–
+
CHARGING SYSTEM
E
FUSE
Refer to “STARTING SYSTEM”.
BATTERY
Refer to “ELECTRICAL” in chapter 3.
RECTIFIER/REGULATOR PEAK
VOLTAGE
1. Measure:
● Rectifier/regulator output peak
voltage
Below specification → Measure the
lighting coil output peak voltage or
replace the rectifier/regulator.
1
Rectifier/regulator output peak
voltage:
Red (R) – Black (B)
r/min
V
Unloaded
Cranking
2,000
3,500
7.5
12.5
12.5
NOTE:
Make sure the output lead (red lead) 1 of
the rectifier/regulator is disconnected when
measuring the output peak voltage.
LIGHTING COIL PEAK VOLTAGE
1. Measure:
● Lighting coil output peak voltage
Below specification → Replace the
lighting coil.
Lighting coil output peak voltage:
Green (G) – Green (G)
r/min
V
Unloaded
Loaded
Cranking
8.5
8.5
2,000
3,500
13
13
NOTE:
Make sure the output lead (red lead) 1 of
the rectifier/regulator is disconnected when
measuring the output peak voltage.
1
7-23
ELEC
–
+
YPVS
E
YPVS
WIRING DIAGRAM
1
B
W/B
W/R
2
L
B
W/B
Br
O
P
W
W/R
W/B
B
L
Gy
G
P
O
Br
B
W/R
Gy
W/B
R
3
R
B Gy
R
B
4
M
R
B
R
5
1
2
3
4
5
Pickup coil
CDI unit
YPVS servomotor
Fuse (10A)
Battery
B
Br
G
Gy
L
O
P
R
W
W/B
W/R
7-24
: Black
: Brown
: Green
: Gray
: Blue
: Orange
: Pink
: Red
: White
: White/black
: White/red
Gy
ELEC
–
+
YPVS
E
FUSE
Refer to “STARTING SYSTEM”.
BATTERY
Refer to “ELECTRICAL” in chapter 3.
PICKUP COIL
Refer to “IGNITION SYSTEM”.
CDI UNIT
Refer to “IGNITION SYSTEM”.
7-25
ELEC
–
+
YPVS SERVOMOTOR
E
YPVS SERVOMOTOR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Q’ty
1
2
3
4
5
6
Procedure/Part name
YPVS SERVOMOTOR REMOVAL
Bolt
Cable holder
YPVS servomotor coupler
Nut/washer
YPVS servomotor
YPVS cable
7
8
9
Cover
Nut/washer
YPVS servomotor bracket
1
3/3
1
2
1
1
2/2
1
2
Service points
Follow the left “Step” for removal.
Slide the cover.
White paint mark a is for No. 2 cable.
Reverse the removal steps for installation.
7-26
ELEC
–
+
YPVS SERVOMOTOR
E
SERVICE POINTS
YPVS cable removal and installation
1. Remove:
● YPVS cables 1 and 2
Removal steps:
● Remove the YPVS cable holder 1.
● Remove the YPVS cables 2 from the
both drams.
NOTE:
● There is a white paint mark a on YPVS
cable 2.
● When installing the YPVS cable, make
sure that the YPVS cable locknuts 3 are
fully turned in.
YPVS cable inspection
1. Inspect:
● YPVS cables 1 and 2
Frays/kinks/rough movement →
Replace.
YPVS servomotor inspection
1. Check:
● YPVS servomotor
YPVS servomotor does not move →
Replace.
Checking steps:
● Connect the battery (12 V) to the YPVS
servomotor coupler as shown.
Battery positive terminal →
Red (R) terminal 1
Battery negative terminal →
Black (B) terminal 2
●
Install a jumper lead 4 between the
black 2 and gray 3 terminals as
shown. Only install the jumper lead for
1 or 2 seconds.
Black (B) terminal 2 ↔
Gray (Gy) terminal 3
7-27
ELEC
–
+
YPVS SERVOMOTOR
E
●
Make sure the servomotor operates
properly.
NOTE:
Make sure the pulley operates three seconds after the jumper lead is removed.
CAUTION:
Do not disassemble the YPVS servomotor
unit. It is a sealed unit and if it is faulty it
must be replaced.
YPVS cable adjustment
Refer to “CONTROL SYSTEM” in
chapter 3.
7-28
–
ELEC
+
INDICATION SYSTEM
E
INDICATION SYSTEM
WIRING DIAGRAM
L
W/L
1
G
G
L
B
W
W/B
B
B
B
O
P
W/R
L
4
Br
B
W/B
L
W/L
B
W/L
2
Gy
G
B
B
3
L
B
B
P
O
L
Br
P
B
G
P
B
P
G G
G
R
P
B
P
P
8
R
B
R
G
B
L/R
6
L/R
L/B
R
R/Y
B/Y
B
L/B
B
R/W
Y
B
R/Y
R/W
W
B
R
Br
SET
PULL
R
Br
R
0
Br
R
R
R
Br
Br
R
R
R
M
R
Br
R
B
R
A
B
1
2
3
4
5
6
7
8
9
0
A
Lighting coil
CDI unit
Fuel level sensor
Oil level sensor
Buzzer
Multifunction meter
Speed sensor
Thermoswitch
Rectifier/regulator
Fuse (10A)
Battery
5
Y
R/Y
Y
B/Y
7
B
R
B
B
Y
9
R
B
Br
G
Gy
L
O
P
R
W
Y
B/Y
: Black
: Brown
: Green
: Gray
: Blue
: Orange
: Pink
: Red
: White
: Yellow
: Black/yellow
7-29
L/B
L/R
R/B
R/W
R/Y
W/B
W/L
W/R
: Blue/black
: Blue/red
: Red/black
: Red/white
: Red/yellow
: White/black
: White/blue
: White/red
Br
ELEC
–
+
INDICATION SYSTEM
E
FUSE
Refer to “STARTING SYSTEM”.
BATTERY
Refer to “ELECTRICAL” in chapter 3.
LIGHTING COIL
Refer to “CHARGING SYSTEM”.
RECTIFIER/REGULATOR
Refer to “CHARGING SYSTEM”.
CDI UNIT
Refer to “IGNITION SYSTEM”.
THERMOSWITCH
Refer to “IGNITION SYSTEM”.
BUZZER
1. Check:
● Buzzer
Buzzer does not sound → Replace.
Checking steps:
● Connect the battery (12 V) to the
buzzer coupler as shown.
Battery positive terminal →
Red (R) terminal 1
Battery negative terminal →
Black (B) terminal 2
OIL LEVEL SENSOR
1. Measure:
● Oil level sensor resistance
Out of specification → Replace.
Blue (L) – Black (B)
Float position
7-30
Resistance (Ω)
A
292–308
B
97–103
C
0–3
ELEC
–
+
INDICATION SYSTEM
E
FUEL LEVEL SENSOR
1. Measure:
● Fuel level sensor resistance
Out of specification → Replace.
White/blue (W/L) – Black (B)
Float position
Resistance (Ω)
A
757–803
B
0–8
MULTIFUNCTION METER
Multifunction meter
1. Check:
● Multifunction meter
Cracked meter housing → Replace
the multifunction meter.
Meter is fogged/shows signs of water
intrusion → Replace the multifunction
meter.
MULTIFUNCTION METER REMOVAL
Refer to “STEERING
COVER” in chapter 8.
7-31
CONSOLE
ELEC
–
+
INDICATION SYSTEM
E
Display function
1. Check:
● Display function
Not operate → Replace the multifunction meter.
1
2
3
4
5
Oil level sensor
Fuel level sensor
Buzzer
Battery
Speed sensor
B
G
L
P
R
Y
L/B
L/R
R/W
W/L
7-32
: Black
: Green
: Blue
: Pink
: Red
: Yellow
: Blue/black
: Blue/red
: Red/white
: White/blue
–
ELEC
+
INDICATION SYSTEM
E
Fuel level gauge
1. Check:
● Fuel level gauge
Not operating → Replace the multifunction meter.
NOTE:
When inspecting the multifunction meter
unit or emptying the oil tank, connect the
blue and black terminals (white two-pin
connector) with a jumper lead 1 to prevent
the oil warning indicator from being activated.
Checking steps:
● Supply DC 12 voltage to the white
four-pin connector (+: red, –: black)
with a battery.
● Disconnect the green two-pin connector (white/blue and black leads).
● Connect the white/blue and black terminals with a jumper lead 2.
● Connect the green and red terminals
with a jumper lead 3.
NOTE:
If the jumper lead is installed for more
than 30 seconds, the display will automatically turn off.
●
●
YAMAHA
8
MPH
7
HOUR
FUEL
6
5
4
MULTI
DISPLAY
3
2
RESET
●
WARNING
●
1
x1000r/min
YAMAHA
8
7
MPH
HOUR
FUEL
6
5
4
MULTI
DISPLAY
3
2
WARNING
1
x1000r/min
5 4
6
7-33
Check the fuel level segments is full
indicated.
Remove the jumper lead 2 from the
green two-pin connector.
Disconnect the jumper lead 3 and
then connect it to green and red terminal again.
Make sure the fuel level segment 4,
fuel symbol 5 and “WARNING” lamp
6 blinks, and the buzzer sounds intermittently.
ELEC
–
+
INDICATION SYSTEM
E
Oil level gauge
1. Check:
● Oil level gauge
Not operating → Replace the multifunction meter.
NOTE:
When inspecting the multifunction meter
unit or emptying the fuel tank, connect the
white/blue and black terminals (green twopin connector) with a jumper lead 1 to prevent the fuel warning indicator from being
activated.
Checking steps:
● Supply DC 12 voltage to the white
four-pin connector (+: red, –: black)
with a battery.
● Disconnect the white two-pin connector (blue and black leads).
● Connect the blue and black terminals
with a jumper lead 2.
● Connect the green and red terminals
with a jumper lead 3.
NOTE:
If the jumper lead is installed for more
than 30 seconds, the display will automatically turn off.
●
●
YAMAHA
8
7
MPH
FUEL
HOUR
6
5
4
●
MULTI
DISPLAY
3
2
WARNING
1
x1000r/min
4
5
7-34
Remove the jumper lead 2 from the
white two-pin connector.
Disconnect the jumper lead 3 and
then connect it to green and red terminal again.
Make sure the oil symbol 4 and
“WARNING” lamp 5 blinks, and the
buzzer sounds intermittently.
ELEC
–
+
INDICATION SYSTEM
E
Overheat warning indicator
1. Check:
● Overheat warning indicator
Not operating → Replace the multifunction meter.
NOTE:
● When
inspecting the multifunction meter
unit or emptying the fuel tank, connect the
white/blue and black terminals (green
two-pin connector) with a jumper lead 1
to prevent the fuel warning indicator from
being activated.
● When inspecting the multifunction meter
unit or emptying the oil tank, connect the
blue and black terminals (white two-pin
connector) with a jumper lead 2 to prevent the oil warning indicator from being
activated.
Checking steps:
● Supply DC 12 voltage to the white
four-pin connector (+: red, –: black)
with a battery.
● Connect the green and red terminals
with a jumper lead 3.
● Connect the pink and black terminals
with a jumper lead 4.
● Make sure the water temperature symbol 5 and “WARNING” lamp 6
blinks, and the buzzer sounds intermittently.
YAMAHA
8
7
MPH
HOUR
6
5
4
FUEL
MULTI
DISPLAY
3
2
WARNING
1
x1000r/min
5
6
7-35
ELEC
–
+
INDICATION SYSTEM
E
Speed meter
1. Check:
● Speed meter output voltage
Within specification → Check the speed
sensor output voltage and pulses.
Out of specification → Replace.
Speed meter output voltage:
10.5 V
NOTE:
● When
inspecting the multifunction meter
unit or emptying the fuel tank, connect the
white/blue and black terminals (green
two-pin connector) with a jumper lead 1
to prevent the fuel warning indicator from
being activated.
● When inspecting the multifunction meter
unit or emptying the oil tank, connect the
blue and black terminals (white two-pin
connector) with a jumper lead 2 to prevent the oil warning indicator from being
activated.
Checking steps:
Supply DC 12 voltage to the white
four-pin connector (+: red, –: black)
with a battery.
● Connect the green and red terminals
with a jumper lead 1.
● Measure the voltage on the speed sensor connector (white three-pin connector) between the red/white and black
leads.
●
7-36
ELEC
–
+
INDICATION SYSTEM
E
Speed sensor
1. Check:
● Speed sensor output voltage and
pulses
Out of specification → Replace.
Speed sensor output voltage
(dependant on the paddle wheel
position):
Less than 400 mV/
More than 11.6 V
Output pulse:
2 pulses/one-full turn
Checking steps:
● Apply DC 12 voltage to the white
three-pin connector (between the red/
yellow and black/yellow leads).
● Rotate the paddle wheel by hand and
measure the voltage between the yellow and black/yellow leads.
NOTE:
As the paddle wheel is rotated, a squarewave voltage signal a is produced.
●
7-37
Two pulses occur every time the paddle wheel makes one-full turn.
HULL
HOOD
E
CHAPTER 8
HULL AND HOOD
HANDLEBAR................................................................................................... 8-1
EXPLODED DIAGRAM ............................................................................. 8-1
REMOVAL AND INSTALLATION CHART ............................................... 8-1
SERVICE POINTS ..................................................................................... 8-7
Handlebar inspection........................................................................ 8-7
Handlebar switch inspection............................................................ 8-7
Handlebar assembly installation ..................................................... 8-7
QSTS GRIP.................................................................................................... 8-10
EXPLODED DIAGRAM ........................................................................... 8-10
REMOVAL AND INSTALLATION CHART ............................................. 8-10
SERVICE POINTS ................................................................................... 8-12
QSTS cable inspection.................................................................... 8-12
QSTS grip inspection...................................................................... 8-12
STEERING COLUMN.................................................................................... 8-13
EXPLODED DIAGRAM ........................................................................... 8-13
REMOVAL AND INSTALLATION CHART ............................................. 8-13
SERVICE POINTS ................................................................................... 8-16
Steering column bushing inspection ............................................ 8-16
REMOTE CONTROL CABLES AND SPEED SENSOR LEAD ...................... 8-17
EXPLODED DIAGRAM ........................................................................... 8-17
REMOVAL AND INSTALLATION CHART ............................................. 8-17
SERVICE POINTS ................................................................................... 8-20
Remote control cables inspection ................................................. 8-20
Steering cable (jet pump side) installation ................................... 8-20
Steering cable stopper installation................................................ 8-20
QSTS cable (jet pump side) installation........................................ 8-21
QSTS cable stopper installation .................................................... 8-21
FRONT HOOD ............................................................................................... 8-22
EXPLODED DIAGRAM ........................................................................... 8-22
REMOVAL AND INSTALLATION CHART ............................................. 8-22
STEERING CONSOLE COVER ..................................................................... 8-24
EXPLODED DIAGRAM ........................................................................... 8-24
REMOVAL AND INSTALLATION CHART ............................................. 8-24
HULL
HOOD
E
BUZZER AND HOOD LOCK ......................................................................... 8-28
EXPLODED DIAGRAM ........................................................................... 8-28
REMOVAL AND INSTALLATION CHART ............................................. 8-28
HOSES........................................................................................................... 8-31
EXPLODED DIAGRAM ........................................................................... 8-31
REMOVAL AND INSTALLATION CHART ............................................. 8-31
SERVICE POINTS ................................................................................... 8-33
Check valve inspection ................................................................... 8-33
Ventilation hose installation........................................................... 8-33
SEATS AND HAND GRIP ............................................................................. 8-34
EXPLODED DIAGRAM ........................................................................... 8-34
REMOVAL AND INSTALLATION CHART ............................................. 8-34
SERVICE POINTS ................................................................................... 8-36
Seat lock inspection ........................................................................ 8-36
BATTERY BOX.............................................................................................. 8-37
EXPLODED DIAGRAM ........................................................................... 8-37
REMOVAL AND INSTALLATION CHART ............................................. 8-37
EXHAUST SYSTEM...................................................................................... 8-39
EXPLODED DIAGRAM ........................................................................... 8-39
REMOVAL AND INSTALLATION CHART ............................................. 8-39
SERVICE POINTS ................................................................................... 8-41
Exhaust system inspection............................................................. 8-41
Exhaust component parts sub-assembly...................................... 8-41
DECK AND HULL .......................................................................................... 8-42
EXPLODED DIAGRAM ........................................................................... 8-42
REMOVAL AND INSTALLATION CHART ............................................. 8-42
ENGINE MOUNT .......................................................................................... 8-44
EXPLODED DIAGRAM ........................................................................... 8-44
REMOVAL AND INSTALLATION CHART ............................................. 8-44
HULL REPAIR ......................................................................................... 8-45
Shallow scratches ........................................................................... 8-45
Deep scratches ................................................................................ 8-45
Cracks and punctures ..................................................................... 8-46
Insert nut.......................................................................................... 8-47
Graphic removal.............................................................................. 8-49
Graphic installation......................................................................... 8-49
1
2
3
4
5
6
7
8
9
HULL
HOOD
HANDLEBAR
E
HANDLEBAR
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
HANDLEBAR COVER REMOVAL
Screw
Handlebar cover
Screw
Handlebar cover stay
Spiral tube
Band
Q’ty
4
1
4
1
1
1
8-1
Service points
Follow the left “Step” for removal.
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
Procedure/Part name
Throttle cable
Choke cable
Bolt
Upper handlebar holder
Handlebar assembly
Lower handlebar holder
Q’ty
1
1
4
2
1
2
Service points
Reverse the removal steps for installation.
8-2
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
Procedure/Part name
HANDLEBAR REMOVAL
QSTS cable (to jet nozzle)
Q’ty
1
Grommet
1
2
3
Handlebar switch coupler
QSTS cable 2
2
1
8-3
Service points
Follow the left “Step” for removal.
Refer to “REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD”.
NOTE:
Apply soapy water to the grommet for
easier installation.
with white tape a
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
Step
4
5
6
7
8
9
Procedure/Part name
QSTS cable 1
Q’ty
1
Handlebar assembly
Nut/washer
QSTS converter
Throttle cable
Choke cable
1
2/2
1
1
1
Service points
NOTE:
Route the QSTS cables behind of the oil
filler hose.
Reverse the removal steps for installation.
8-4
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
Procedure/Part name
HANDLEBAR DISASSEMBLY
Band
Bolt
Grip end
Spacer
Screw/washer/spring washer
QSTS grip assembly
Screw
Handlebar switch assembly
Cable holder
Q’ty
1
2
2
1
1/1/1
1
2
1
1
8-5
Service points
Follow the left “Step” for disassembly.
HULL
HOOD
HANDLEBAR
E
EXPLODED DIAGRAM
Step
10
11
12
13
14
15
Procedure/Part name
Screw
Throttle lever assembly
Screw
Choke lever assembly
Handlebar grip
Handlebar
Q’ty
2
1
2
1
1
Service points
NOTE:
Apply adhesive to the handlebar and the
inner surface of the handlebar grip.
1
Reverse the disassembly steps for
assembly.
8-6
HULL
HOOD
HANDLEBAR
E
SERVICE POINTS
Handlebar inspection
1. Inspect:
● Handlebar
Bends/cracks/damage → Replace.
Handlebar switch inspection
Refer to “IGNITION SYSTEM” and
“STARTING SYSTEM” in chapter 7.
Handlebar assembly installation
1. Adjust:
● QSTS cable length a
QSTS cable length:
77 ± 0.5 mm (3.03 ± 0.02 in)
NOTE:
● Before
adjusting the QSTS cables, set the
control grip to the neutral position.
● Adjust the QSTS cable lengths a to the
specified length and be sure to take up
any slack.
2. Install:
● Upper handlebar holder 1
NOTE:
● Align the punch marks a on the handlebar with the top surface of the handlebar
holder.
● The upper handlebar holder should be
installed with the punch mark b facing
forward.
CAUTION:
Clearance c should be narrower than
clearance d.
8-7
HULL
HOOD
HANDLEBAR
E
3. Install:
● Throttle cable
NOTE:
Fit the seal into the glove in the bracket.
4. Install:
● Band 1
NOTE:
After inserting the QSTS cables into the
grommet, tie the end of grommet with the
band.
5. Install:
● Spiral tube 1
NOTE:
Be sure to install the spiral tube, containing
the throttle cable, choke cable and handlebar switch lead, at least 50 mm (1.97 in) a
into the steering column.
6. Install:
● Handlebar cover 1
NOTE:
When the handlebar cover is in contact with
the steering console cover, adjust the handlebar mount angle so that the clearance a
and b are equal.
8-8
HULL
HOOD
HANDLEBAR
E
7. Adjust:
● Choke lever operation
Refer to “CONTROL SYSTEM” in
chapter 3.
8. Adjust:
● Throttle lever free play
Refer to “CONTROL SYSTEM” in
chapter 3.
9. Adjust:
● QSTS cable
Refer to “CONTROL SYSTEM” in
chapter 3.
8-9
HULL
HOOD
QSTS GRIP
E
QSTS GRIP
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
QSTS GRIP DISASSEMBLY
QSTS grip assembly
Screw/washer
Cover
Ball
Spring
QSTS cable 1
QSTS cable 2
Q’ty
1/1
1
2
2
1
1
8-10
Service points
Follow the left “Step” for disassembly.
Refer to “HANDLEBAR”.
with white tape a
HULL
HOOD
QSTS GRIP
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
13
Procedure/Part name
Screw/washer
Collar
QSTS shift lock lever
Spring
Spacer
QSTS cable housing cover
QSTS shift grip
Q’ty
2/2
1
1
1
1
1
1
Service points
Reverse the disassembly steps for
assembly.
8-11
HULL
HOOD
QSTS GRIP
E
SERVICE POINTS
QSTS cable inspection
1. Inspect:
● QSTS cables
Frays/kinks/rough movement →
Replace.
QSTS grip inspection
1. Inspect:
● QSTS grip
Damage/wear → Replace.
8-12
HULL
HOOD
STEERING COLUMN
E
STEERING COLUMN
EXPLODED DIAGRAM
16 N • m (1.6 kgf • m, 11 ft • Ib)
1
2
3
4
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
Procedure/Part name
STEERING COLUMN REMOVAL
Steering console cover assembly
Steering cable end
Nut
Plate
Steering column assembly
Rubber seal
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “STEERING CONSOLE COVER”.
Refer to “REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD”.
4
1
1
1
Reverse the removal steps for installation.
8-13
HULL
HOOD
STEERING COLUMN
E
EXPLODED DIAGRAM
6
8
1
7
2
5
7
4
8 × 60 mm
16 N • m (1.6 kgf • m, 11 ft • Ib)
3
26 N • m (2.6 kgf • m, 19 ft • Ib)
5 N • m (0.5 kgf • m, 3.6 ft • Ib)
2
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
Procedure/Part name
STEERING COLUMN
DISASSEMBLY
Grommet
Bolt/washer/nut
Steering arm
Shim
Q’ty
Service points
Follow the left “Step” for disassembly.
1
1/2/1
1
*
*: Be sure to install the same number of shim(s) as installed originally at factory.
8-14
HULL
HOOD
STEERING COLUMN
E
EXPLODED DIAGRAM
6
8
1
7
2
5
7
4
8 × 60 mm
16 N • m (1.6 kgf • m, 11 ft • Ib)
3
26 N • m (2.6 kgf • m, 19 ft • Ib)
5 N • m (0.5 kgf • m, 3.6 ft • Ib)
2
Step
5
6
7
8
Procedure/Part name
Washer
Steering column
Bushing
Steering column housing
Q’ty
1
1
2
1
Service points
Reverse the disassembly steps for
assembly.
8-15
HULL
HOOD
STEERING COLUMN
E
SERVICE POINTS
Steering column bushing inspection
1. Inspect:
● Bushings
Damage/wear → Replace.
2. Inspect:
● Steering column inspection
Refer to “CONTROL SYSTEM” in
chapter 3.
8-16
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
REMOTE CONTROL CABLES AND SPEED SENSOR LEAD
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD
REMOVAL
Speed sensor coupler
Cap
Nut
Screw
Speed sensor
Steering cable end
Bolt
Steering cable holder
Q’ty
1
1
1
4
1
1
1
1
8-17
Service points
Follow the left “Step” for removal.
E
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
EXPLODED DIAGRAM
Step
9
10
11
12
13
14
15
16
17
Procedure/Part name
Cap
Nut
Steering cable
Nut
Pin
QSTS cable end
Cap
Nut
QSTS cable
Q’ty
1
1
1
1
1
1
1
1
1
Service points
Reverse the removal steps for installation.
8-18
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
EXPLODED DIAGRAM
1
2
FWD
REMOVAL AND INSTALLATION CHART
Step
1
2
Procedure/Part name
SPEED SENSOR DISASSEMBLY
Paddle wheel set
Speed sensor housing
Q’ty
1
1
Service points
Follow the left “Step” for disassembly.
Not reusable
Reverse the disassembly steps for
assembly.
8-19
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
HULL
HOOD
E
SERVICE POINTS
WARNING
When routing the cables, do not grasp the
cable by the outer crimped sheath or steel
end. This could deform or loosen the cable
end due to extreme angles and or pressure.
Always hold the cables by the bracket or
outer cover below the crimp.
If a cable becomes damaged replace it.
Never attempt to repair a damaged cable.
Remote control cables inspection
1. Inspect:
● Steering cable
● QSTS cable
Frays/kinks/rough movement →
Replace.
Steering cable (jet pump side) installation
1. Install:
● Steering cable a
Steering cable set length
(jet pump side):
13.5–15.5 mm (0.53–0.61 in)
WARNING
The steering cable must be screwed in at
least 8 mm (0.31 in).
Steering cable stopper installation
1. Install:
● Steering cable stopper
1
WARNING
Be sure to fit the steering cable into the
glove 1 in the steering cable bracket.
8-20
HULL
HOOD
REMOTE CONTROL CABLES AND
SPEED SENSOR LEAD
E
QSTS cable (jet pump side) installation
1. Install:
● QSTS cable (jet pump side) a
QSTS cable set length
(jet pump side):
12.0–14.0 mm (0.47–0.55 in)
WARNING
The QSTS cable must be screwed in more
than 8 mm (0.31 in).
QSTS cable stopper installation
1. Install:
● QSTS cable stopper
WARNING
Be sure to fit the projection 1 on the QSTS
cable stopper into the glove in the outer
cable.
8-21
HULL
HOOD
FRONT HOOD
E
FRONT HOOD
EXPLODED DIAGRAM
6 × 14 mm
5 N • m (0.5 kgf • m, 3.6 ft • Ib)
6
7
6 × 14 mm
12 N • m (1.2 kgf • m, 8.7 ft • Ib)
1
11
3
2
5
4
8
5 × 20 mm
1 N • m (0.1 kgf • m, 0.7 ft • Ib)
10
9
16 N • m (1.6 kgf • m, 11 ft • Ib)
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
FRONT HOOD REMOVAL
Bolt
Screw
Seal washer
Visor
Pop nut
Bolt
Q’ty
2
8
8
1
8
2
8-22
Service points
Follow the left “Step” for removal.
HULL
HOOD
FRONT HOOD
E
EXPLODED DIAGRAM
6 × 14 mm
5 N • m (0.5 kgf • m, 3.6 ft • Ib)
6
7
6 × 14 mm
12 N • m (1.2 kgf • m, 8.7 ft • Ib)
1
11
2
3
5
4
8
5 × 20 mm
1 N • m (0.1 kgf • m, 0.7 ft • Ib)
10
9
16 N • m (1.6 kgf • m, 11 ft • Ib)
Step
7
8
9
10
11
Procedure/Part name
Hood lock
Front hood
Nut
Plate
Hinge assembly
Q’ty
1
1
2
1
1
Service points
Reverse the removal steps for installation.
8-23
HULL
HOOD
STEERING CONSOLE COVER
E
STEERING CONSOLE COVER
EXPLODED DIAGRAM
8 × 25 mm
8
2 N • m (0.2 kgf • m, 1.4 ft • Ib)
5 × 19 mm
5
9
6
4
2
3 N • m (0.3 kgf • m, 2.2 ft • Ib)
6 × 25 mm
3
1
7
5 N • m (0.5 kgf • m, 3.6 ft • Ib)
16 N • m (1.6 kgf • m, 11 ft • Ib)
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
STEERING CONSOLE COVER
REMOVAL
Handlebar assembly
Knob (fuel cock)
Q’ty
Band
Multifunction meter coupler
Nut/washer
Bolt/washer
Screw
1
5
2/2
4/4
2
Service points
Follow the left “Step” for removal.
Refer to “HANDLEBAR”.
Refer to “FUEL COCK AND FUEL FILTER”
in chapter 4.
8-24
HULL
HOOD
STEERING CONSOLE COVER
E
EXPLODED DIAGRAM
8 × 25 mm
8
2 N • m (0.2 kgf • m, 1.4 ft • Ib)
5 × 19 mm
5
9
6
4
2
3 N • m (0.3 kgf • m, 2.2 ft • Ib)
6 × 25 mm
3
1
7
5 N • m (0.5 kgf • m, 3.6 ft • Ib)
16 N • m (1.6 kgf • m, 11 ft • Ib)
Step
6
7
8
9
Procedure/Part name
Plate
Nut/washer
Bolt/square-ring
Steering console cover assembly
Q’ty
1
2/2
2/2
1
Service points
NOTE:
Remove the oil filler cap to remove the
steering console cover assembly easier.
Reverse the removal steps for installation.
8-25
HULL
HOOD
STEERING CONSOLE COVER
E
EXPLODED DIAGRAM
1 N • m (0.1 kgf • m, 0.7 ft • Ib)
5 × 20 mm
5
6
2
9
1
8
3 N • m (0.3 kgf • m, 2.2 ft • Ib)
6 × 18 mm
2
7
4
3
2 N • m (0.2 kgf • m, 1.4 ft • Ib)
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
STEERING CONSOLE COVER
DISASSEMBLY
Screw
Side cover
Nut
Holder
Multifunction meter
Q’ty
4
2
2
1
1
8-26
Service points
Follow the left “Step” for disassembly.
HULL
HOOD
STEERING CONSOLE COVER
E
EXPLODED DIAGRAM
1 N • m (0.1 kgf • m, 0.7 ft • Ib)
5 × 20 mm
5
6
2
9
1
8
3 N • m (0.3 kgf • m, 2.2 ft • Ib)
6 × 18 mm
2
7
4
3
Step
6
7
8
9
2 N • m (0.2 kgf • m, 1.4 ft • Ib)
Procedure/Part name
Screw
Glove compartment
Pop nut
Steering console cover
Q’ty
4
1
4
1
Service points
Reverse the disassembly steps for
assembly.
8-27
HULL
HOOD
BUZZER AND HOOD LOCK
E
BUZZER AND HOOD LOCK
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
Procedure/Part name
BUZZER AND HOOD LOCK
REMOVAL
Steering console cover assembly
Steering cable
Ring nut
Buzzer
Bolt
Bracket
Bracket
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “STEERING CONSOLE COVER”.
Refer to “REMOTE CONTROL CABLES
AND SPEED SENSOR LEAD”.
1
1
3
1
1
8-28
HULL
HOOD
BUZZER AND HOOD LOCK
E
EXPLODED DIAGRAM
Step
6
7
8
9
Procedure/Part name
Nut
Bolt
Hood lock assembly
Grommet
Q’ty
2
2
1
1
Service points
Reverse the removal steps for installation.
8-29
HULL
HOOD
BUZZER AND HOOD LOCK
E
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
Procedure/Part name
HOOD LOCK DISASSEMBLY
Screw
Hood lock button assembly
Circlip
Washer
Pin
Hook lever
Spring
Hood lock body
Q’ty
Service points
Follow the left “Step” for disassembly.
2
1
1
1
1
1
1
1
Reverse the disassembly steps for
assembly.
8-30
HULL
HOOD
HOSES
E
HOSES
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
Procedure/Part name
HOSES REMOVAL
Engine unit
Steering console cover assembly
Band
Ventilation hose (stern side)
Ventilation hose (bow side)
Q’ty
2
1
1
8-31
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT” in chapter 5.
Refer to “STEERING CONSOLE COVER”.
NOTE:
● Route the ventilation hose (bow side) in
front of the fuel level sensor lead.
● Route the ventilation hose (stern side)
front the oil level sensor lead and the oil
tank breather hose.
HULL
HOOD
HOSES
E
EXPLODED DIAGRAM
Step
4
5
6
7
Procedure/Part name
Band
Check valve
Oil tank breather hose
Fuel tank breather hose
Q’ty
1
1
1
2
Service points
Reverse the removal steps for installation.
8-32
HULL
HOOD
HOSES
E
SERVICE POINTS
Check valve inspection
1. Check:
● Check valve
Faulty → Replace.
Checking steps:
Connect a hose to the end of check
valve “A” and blow into it.
Air should come out from end “B”.
● Connect the hose to the end of check
valve “B” and blow into it.
Air should not come out from end “A”.
●
Ventilation hose installation
1. Install:
● Ventilation hose
a
NOTE:
Insert the ventilation hose into the ventilation fitting until it reaches the bend a in the
fitting.
a
8-33
HULL
HOOD
SEATS AND HAND GRIP
SEATS AND HAND GRIP
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
Procedure/Part name
SEATS AND HAND GRIP
REMOVAL
Seat assembly
Bolt
Seat lock assembly
Nut
Notch
Washer
Q’ty
1
2
1
1
1
1
8-34
Service points
Follow the left “Step” for removal.
E
HULL
HOOD
SEATS AND HAND GRIP
E
EXPLODED DIAGRAM
Step
7
8
9
10
11
12
Procedure/Part name
Rubber ring
Nut/washer
Bolt
Bolt
Hand grip
Bracket
Q’ty
1
2/2
2
2
1
1
Service points
Reverse the removal steps for installation.
8-35
HULL
HOOD
SEATS AND HAND GRIP
SERVICE POINTS
Seat lock inspection
1. Inspect:
● Seat lock
Damage/wear → Replace.
8-36
E
HULL
HOOD
BATTERY BOX
E
BATTERY BOX
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
8
9
10
11
Procedure/Part name
BATTERY BOX REMOVAL
Band
Fire extinguisher container
Band
Bolt
Battery negative lead
Terminal extension
Bolt
Battery positive lead
Clip/breather hose
Battery
Bolt
Q’ty
1
1
1
1
1
1
1
1
1/1
1
3
8-37
Service points
Follow the left “Step” for removal.
HULL
HOOD
BATTERY BOX
E
EXPLODED DIAGRAM
Step
12
13
14
15
16
17
18
Procedure/Part name
Electrical box
Cap nut/washer
Holder
Holder
Cap nut/washer
Battery box
Stay
Q’ty
1
2/2
1
1
2/2
1
Service points
NOTE:
Before installing the battery box, route
the battery leads and battery breather
hose through the holes of the battery box.
1
Reverse the removal steps for installation.
8-38
HULL
HOOD
EXHAUST SYSTEM
E
EXHAUST SYSTEM
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
EXHAUST SYSTEM REMOVAL
Battery box
Jet pump unit assembly
Floatation
Floatation
Water lock band
Hose clamp
Rubber joint
Hose clamp
Rubber hose
Q’ty
1
1
1
2
1
2
1
8-39
Service points
Follow the left “Step” for removal.
Refer to “BATTERY BOX”.
Refer to “JET PUMP UNIT” in chapter 6.
HULL
HOOD
EXHAUST SYSTEM
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
Procedure/Part name
Water lock
Bolt
Packing
Hose clamp
Water tank
Rubber hose
Exhaust outlet
Q’ty
1
3
1
2
1
1
1
Service points
NOTE:
Remove parts 11 to 14 as a set.
Reverse the removal steps for installation.
8-40
HULL
HOOD
EXHAUST SYSTEM
E
SERVICE POINTS
Exhaust system inspection
1. Inspect:
● Water lock band
Cracks/damage → Replace.
2. Inspect:
● Rubber hoses
Burns/cracks/damage → Replace.
3. Inspect:
● Water lock
Cracks/leaks → Replace.
4. Inspect:
● Water tank
Cracks/damage/leaks → Replace.
Exhaust component parts sub-assembly
1. Install:
● Exhaust outlet
● Rubber hose
● Water tank
NOTE:
the exhaust outlet 45 mm (1.8 in) a
into the rubber hose.
● Make sure that there is a surface distance
of 10 mm (0.4 in) b between the parting
lines of the exhaust outlet and the rubber
hose.
● Insert the water tank 45 mm (1.8 in) c into
the rubber hose.
● Make sure that there is a surface distance
of 45 mm (1.8 in) d between the parting
lines of the water tank and rubber hose.
● Insert
b
d
8-41
HULL
HOOD
DECK AND HULL
E
DECK AND HULL
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
5
6
7
Procedure/Part name
DECK AND HULL DISASSEMBLY
Bolt
Bow eye
Nut
Rope hole fitting
Nut
Spout
Bolt
Q’ty
2
1
2
2
1
1
6
8-42
Service points
Follow the left “Step” for disassembly.
HULL
HOOD
DECK AND HULL
E
EXPLODED DIAGRAM
Step
8
9
10
11
12
13
14
Procedure/Part name
Sponson
Q’ty
2
Bolt
Flap
Nut/washer
Screw/washer
Drain plug
Packing
8
2
4/4
4/4
2
2
Service points
NOTE:
Make sure install the starboard and port
side sponsons to the same position.
Reverse the disassembly steps for
assembly.
8-43
HULL
HOOD
ENGINE MOUNT
E
ENGINE MOUNT
EXPLODED DIAGRAM
REMOVAL AND INSTALLATION CHART
Step
1
2
3
4
Procedure/Part name
ENGINE MOUNT REMOVAL
Engine unit
Bolt
Damper
Bolt
Engine mount
Q’ty
Service points
Follow the left “Step” for removal.
Refer to “ENGINE UNIT” in chapter 5.
2
1
8
4
Reverse the removal steps for installation.
8-44
HULL
HOOD
ENGINE MOUNT
E
HULL REPAIR
Shallow scratches
1. Sand the scratches with 400 grit sandpaper (either wet or dry) until the
scratches are smooth. Then, sand the
scratches once again with 600 grit sandpaper (either wet or dry).
Deep scratches
1. Remove any sharp or rough edges from
the hull surface.
2. Sand the scratches and a 1-inch circumference around them with 80 grit sandpaper (either wet or dry).
3. Clean the entire area with acetone and
let it completely dry.
4. Mix gel-coat and gel-coat thickener to
form a putty, and then add the catalyst
to the putty.
5. Apply the putty, spread it with a squeegee, and then cover the putty with wax
paper.
6. When the putty has set, sand it. Smooth
the area with 80–400 grit sandpaper
(either wet or dry) and a sanding block.
7. Clean the area with a dry cloth and then
polish it.
WARNING
Resins, catalysts, and solvents are flammable and toxic; only use them in a well-ventilated area and keep them away from open
flames and sparks. Always follow the manufacturer’s instructions and warnings.
8-45
HULL
HOOD
ENGINE MOUNT
E
Cracks and punctures
NOTE:
Before attempting to repair any cracks or
punctures, refer to “WATERCRAFT FRP
REPAIR MANUAL”.
1. Remove any damaged fiberglass.
2. Cut the damaged area and separate it
approximately 0.25 inch.
3. On the outside of the hull, grind the
separated edge of the area to less than
5˚ as shown.
4. Working from inside the hull, grind the
damaged area approximately 4 inches
beyond the damage.
5. Clean the area with acetone, apply BP-1
or an equivalent primer onto both sides
of the damaged area, and then allow it
to cure for approximately 30 minutes.
6. Cover a piece of cardboard with wax
paper 1 and then cover the damaged
area with it.
7. Combine the polyester resin and the
catalyst, and then apply the mixture
onto the hull.
8. Install a glass mat 2 (2 inches smaller
than the ground area).
9. Apply the resin.
10. Install a 20 oz. fiberglass cloth 3 (1 inch
smaller than the glass mat).
11. Apply the resin.
12. Install another glass mat 4 (1 inch
smaller than the ground area).
13. When the resin has hardened remove
the piece of cardboard.
14. Finish the outer surface.
Refer to steps (3)–(7) in the “Deep
scratches” section.
8-46
HULL
HOOD
ENGINE MOUNT
E
Insert nut
NOTE:
Use the insert nut when:
● A pop nut which was attached to the hull
slipped off or,
● When a bolt which was fastened to an
insert nut or pop nut broke.
Part No.
Part
name
Remarks
EW2-62733-09
Nut
Stainless
steel, M6
●
●
●
Nut 1
Thread direction 2
Slot to be threaded 3
NOTE:
Drilling size
Material
Pilot hole diameter
FRP or SMC
9.1–9.2 mm (0.36 in)
Brass
9.4 mm (0.37 in)
Example 1:
NOTE:
Before attempting to install the insert nut,
refer to “WATERCRAFT FRP REPAIR MANUAL”.
The insert nut is used to repair the pop nut
designed for the ride plate.
(By repairing the FRP portion, the insert nut
can be used for all models.)
1. Remove:
● Pop nut
2. Clean the surface to be scarfed and the
inside of the hull with acetone.
3. Scarf the shaded portion of the hull.
8-47
HULL
HOOD
ENGINE MOUNT
E
4. First, apply tape 1 to the inner surface
of the hull and then laminate fiberglass
mats over the tape with resin.
NOTE:
When it is possible to work inside the hull,
laminate the mats from the inside.
5. Sand the outer surface of the hull until it
is smooth.
6. Install the ride plate.
7. Drill a 20 mm (0.79 in) deep hole in the
center of the laminated fiberglass layers
with a 9.2 mm (0.36 in) diameter drill
bit.
8. Pass the bolt 2 through the insert nut
and lock the bolt with the nut 3 as
shown.
9. Screw in the insert nut so that the top is
flush with the FRP surface.
10. Loosen the locknut and remove the
bolt.
CAUTION:
● Only
use a steel bolt with a tensile
strength of 8T or more.
● If the bolt is inferior in strength or is
made of stainless steel it may break.
Bolt 2
● Locknut 3
Example 2:
The brass insert nut, which is designed for
the Super Jet ride plate or the intake screen,
is used as follows.
●
NOTE:
If the bolt is broken, drill it out.
1. Drill a hole in the hull.
NOTE:
● First, use a small-diameter drill bit followed by drill bits of gradually increasing
diameter.
● Use a 9.4 mm (0.37 in) drill bit for the final
drilling.
8-48
HULL
HOOD
ENGINE MOUNT
E
2. To prevent water from entering the urethane foam, apply silicone sealant to
the inside of the hole as shown.
3. Install the insert nut as explained in
“Example 1”.
● Brass insert nut 1
● Hull 2
● Urethane foam 3
● Silicone sealant 4
Graphic removal
1. Hold a hair dryer approximately 1.5
inches above the graphic 1.
2. Apply heat to one corner of the graphic.
3. Slowly peel off the heated portion of the
graphic and continue working until you
reach the opposite corner and the entire
graphic is removed.
4. After the graphic is removed, clean the
entire bow area with isopropyl alcohol
to remove any residual adhesive.
Graphic installation
1. Mix 1 tablespoon of liquid detergent
and water in a 1-quart spray bottle.
2. Remove the backing from the new
graphic.
3. Spray the soap and water mixture onto
both sides of the graphic, and also onto
the hull area where the graphic will be
installed.
NOTE:
Spraying the front of the graphic with the
soap and water mixture will protect it from
being scratched during installation.
4. Align the graphic onto the fitting area of
the hull and position it with a squeegee.
NOTE:
Be sure to remove any air bubbles from the
graphic with the squeegee. Work from the
top of the graphic down and slide the
squeegee outwards from the graphic’s center line.
5. Allow the graphic to dry before waxing
or using the watercraft.
8-49
TRBL
ANLS
E
CHAPTER 9
TROUBLE ANALYSIS
TROUBLE ANALYSIS ..................................................................................... 9-1
TROUBLE ANALYSIS CHART ................................................................. 9-1
1
2
3
4
5
6
7
8
9
TRBL
ANLS
TROUBLE ANALYSIS
E
TROUBLE ANALYSIS
NOTE:
The following items should be checked before the “Trouble analysis” chart is consulted.
1. The battery is charged and its specified gravity is within specification.
2. There are no incorrect wiring connections.
3. Wiring connections are properly secured and not rusty.
4. The lock plate is attached to the engine stop lanyard switch.
5. Fuel is reaching the carburetors.
TROUBLE ANALYSIS CHART
YPVS SERVOMOTOR DOES NOT MOVE
POOR BATTERY CHARGING
IRREGULAR WARNING INDICATION
Items to be checked
BILGE INCREASE
LOOSE STEERING
OVERHEATING
POOR PERFORMANCE
ENGINE WILL NOT STOP
ENGINE STALLS
ROUGH IDLING
ENGINE WILL NOT START
Problems
Items
FUEL SYSTEM
Fuel tank
Fuel tank breather hose
Fuel hose
Fuel filter
Fuel pump
Carburetors
Carburetor synchronization
Trolling speed
POWER UNIT
Spark plug(s)
Compression
Reed valves
Cylinder head gasket
Piston rings
Cylinder block
Seals
Crankcase
Pistons
Bearings
Bearing housing
Drive couplings
Rubber coupling
9-1
Reference
chapter
4
4
4
4
4
4
4
3
3
5
5
5
5
5
5
5
5
5
5
5
5
TRBL
ANLS
TROUBLE ANALYSIS
YPVS SERVOMOTOR DOES NOT MOVE
POOR BATTERY CHARGING
IRREGULAR WARNING INDICATION
Items to be checked
BILGE INCREASE
LOOSE STEERING
OVERHEATING
POOR PERFORMANCE
ENGINE WILL NOT STOP
ENGINE STALLS
ROUGH IDLING
ENGINE WILL NOT START
Problems
E
Items
Pilot water hose
Water hose
Water passage
JET PUMP UNIT
Duct
Impeller
Intake grate
Bearings
Intake duct
Water inlet hose
Bilge hose
Bilge strainer
Bilge hose joint
Valve body
ELECTRICAL
CDI unit
Lighting coil
Charge coil
Pickup coil (Pulser coil)
Ignition coil
Rectifier/regulator
Electrical sensor(s)
Starter relay, starter motor
YPVS unit
Battery
Fuse(s)
Wire harness, electrical coupler(s)
HULL AND HOOD
Steering column
Water lock
Exhaust hose
Muffler
Drain plugs
9-2
Reference
chapter
5
5
5
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
3
7
7
8
8
8
8
8
YAMAHA MOTOR CORPORATION, USA
Printed in USA
Nov. 2000 — ?.? × 1 CR
F0W-28197-1A-11
(GP800A)
WIRING DIAGRAM
COLOR CODE
B : Black
Br : Brown
G : Green
Gy : Gray
L : Blue
O : Orange
P : Pink
R : Red
W : White
GP800R
Y
: Yellow
B/Y : Black/yellow
L/B : Blue/black
L/R : Blue/red
R/W : Red/white
R/Y : Red/yellow
W/B : White/black
W/L : White/blue
W/R : White/red
3 Lighting coil
4 Pickup
coil
C Oil level sensor
G G
L
L
W/B
W/R
5 Charge coil
Br
B
L
L
B
B
B
W/L
B
B
B
W/L
W/L
B
W/L
D Fuel level sensor
7 Starter motor
M
6 CDI unit
1 Thermoswitch
B
Br
O
L
B
P
W/R
W
W/B
P
B
E Multifunction
meter
P
G G
R B
B/Y
Br
O
B
R/Y
R/Y
Y
B/Y
F Speed
sensor
Br W/B
P
L
W/R O
W
R/W
Y
B
Y
H Engine stop
G Engine stop switch lanyard switch I Start switch
G G
W B R Br
SET
PULL
Gy
G
W
B
R
P
B
O
P
P
P
B
B
R
P
B
W W
W
B
B
W
W
B
B
R
R
R
R
R
R
R
Br
Br
Br
R
R
Br
Br
8 Rectifier/
regulator
B
B
Br
R
R
B
0 Fuse (10A)
B
R
R
R
R
R
R
Gy
B
R
Gy
B
Gy
9 Starter relay
A Battery
B YPVS servomotor
R
R
B
P
Y
B
L/B
B
G R P B
L
B
L/R
L/R
L/B
R/W
W
O
W/B Br
B
G G W/R
L
B
G
G
2 Ignition coil
R
G
R
P
B
Gy
W/R
B
R
Gy
Br
J Buzzer