RXV750_U_cv.fm Page 1 Monday, January 19, 2004 10:04 AM
U
SPECIFICATIONS
AUDIO SECTION
VIDEO SECTION
• Minimum RMS Output Power for Front, Center, Surround,
Surround back
20 Hz to 20 kHz, 0.06% THD, 8 Ω .................................... 100 W
• Video Signal Type ......................................................... PAL/NTSC
• Maximum Power (EIAJ)
[China, Korea and General models]
1 kHz, 10% THD, 8 Ω ....................................................... 140 W
• Dynamic Power (IHF)
8/6/4/2 Ω .......................................................135/170/200/245 W
• DIN Standard Output Power [U.K., Europe and Asia models]
1 kHz, 0.7% THD, 4 Ω ...................................................... 150 W
• IEC Output Power [U.K., Asia and Europe models]
1 kHz, 0.06% THD, 8 Ω .................................................... 110 W
• Signal to Noise Ratio ............................................................. 50 dB
• Frequency Response (MONITOR OUT)
Composite, S-Video ................................ 5 Hz to 10 MHz, –3 dB
Component ............................................. 5 Hz to 60 MHz, –3 dB
FM SECTION
• Tuning Range
[U.S.A. and Canada models] ......................... 87.5 to 107.9 MHz
[Asia and General model] ........ 87.5/87.50 to 108.0/108.00 MHz
[Other models] ........................................... 87.50 to 108.00 MHz
• Usable Sensitivity (IHF) ...................................... 1.0 µV (11.2 dBf)
• Damping Factor (IHF)
20 Hz to 20 kHz, 8 Ω ................................................ 100 or more
• Signal to Noise Ratio (IHF)
Mono/Stereo ............................................................ 76 dB/70 dB
• Frequency Response
CD terminal to Front L/R ..................... 10 Hz to 100 kHz, –3 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo .............................................................. 0.2%/0.3%
• Total Harmonic Distortion
PHONO to REC OUT (20 Hz to 20 kHz, 1 V) ................. 0.02%
CD, etc. to Front L/R (20 Hz to 20 kHz, 50 W, 8 Ω) ........ 0.06%
• Stereo Separation (1 kHz) ...................................................... 42 dB
• Signal to Noise Ratio (IHF-A Network)
Phono (5 mV) to REC OUT
[U.K., Europe, Australia and Asia models] ........................ 81 dB
[Other models] .................................................................... 86 dB
CD (250 mV) to Front L/R, Effect Off ............................. 100 dB
AM SECTION
• Residual Noise (IHF-A Network)
Front L/R .............................................................. 150 µV or less
• Usable Sensitivity ........................................................... 300 µV/m
• Channel Separation (1 kHz/10 kHz)
PHONO (shorted) to Front L/R .............................. 60 dB/55 dB
CD (5.1 kΩ terminated) to Front L/R ..................... 60 dB/45 dB
• Tone Control (Front L/R)
BASS Boost/Cut ...................................................... ±6 dB/50 Hz
BASS Turnover Frequency ............................................... 350 Hz
TREBLE Boost/Cut .............................................. ±6 dB/20 kHz
TREBLE Turnover Frequency ......................................... 3.5 kHz
• Phones Output ......................................................... 150 mV/100 Ω
• Input Sensitivity/Input Impedance
PHONO ................................................................. 2.5 mV/47 kΩ
CD, etc. ................................................................ 200 mV/47 kΩ
MULTI CH INPUT .............................................. 200 mV/47 kΩ
• Output Level/Output Impedance
REC OUT ............................................................ 200 mV/1.2 kΩ
PRE OUT ....................................................................2 V/1.2 kΩ
SUB WOOFER .......................................................... 4 V/1.7 kΩ
ZONE 2 OUTPUT
[U.S.A., Canada and Australia models] ........... 200 mV/1.2 kΩ
RX-V750
AV Receiver
• Frequency Response ........................ 20 Hz to 15 kHz, +0.5, –2 dB
• Tuning Range
[U.S.A. and Canada models] ............................ 530 to 1710 kHz
[Asia and General models] ............... 530/531 to 1710/1611 kHz
[Other models] .................................................. 531 to 1611 kHz
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................ AC 120 V, 60 Hz
[Australia model] .............................................. AC 240 V, 50 Hz
[China model] ................................................... AC 220 V, 50 Hz
[Korea model] ................................................... AC 220 V, 60 Hz
[U.K. and Europe models] ................................ AC 230 V, 50 Hz
[General model] .............. AC 110/120/220/230-240 V, 50/60 Hz
[Asia model] ................................. AC 220/230-240 V, 50/60 Hz
• Power Consumption
[U.S.A. and Canada models] ............................... 400 W/500 VA
[Other models] .................................................................. 440 W
• Standby Power Consumption ............................................... 0.1 W
• AC Outlets
[U.K. and Australia models] ............. 1 (Total 100 W maximum)
[China, Asia and General models] ...... 2 (Total 50 W maximum)
[Other models] .................................. 2 (Total 100 W maximum)
• Dimension (W x H x D) ................................ 435 x 171 x 420 mm
(17-1/8” x 6-3/4” x 16-1/2”)
• Weight ............................................................ 12.5 kg (27 lbs 9 oz)
© 2004
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WC85490
00_RXV750_U_EN.book Page i Tuesday, February 17, 2004 10:08 AM
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
10
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
8
9
i
11
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven
surfaces may cause the product and cart
combination to overturn.
12
13
14
15
16
17
18
19
Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
00_RXV750_U_EN.book Page ii Tuesday, February 17, 2004 10:08 AM
IMPORTANT SAFETY INSTRUCTIONS
d)
20
21
22
23
If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in performance - this indicates a need for service.
Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
24
Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
MAST
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2 IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
ii
00_RXV750_U_EN.book Page iii Tuesday, February 17, 2004 10:08 AM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool,
dry, clean place — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
Allow ventilation space of at least 30 cm on the top,
20 cm on the left and right, and 20 cm on the back of
this unit.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this unit
in a environment with high humidity (i.e. a room with
a humidifier) to prevent condensation inside this
unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed to
liquid dripping or splashing. On the top of this unit,
do not place:
– Other components, as they may cause damage
and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause
fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause
fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power plug
from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding that
this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
18 VOLTAGE SELECTOR (Asia and General models
only)
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local main voltage BEFORE
plugging into the AC main supply. Voltages are:
Asia model ...................... 220/230-240 V AC, 50/60 Hz
General model .. 110/120/220/230-240 V AC, 50/60 Hz
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of
power.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
We Want You Listening For A Lifetime
YAMAHA and the Electronic Industries Association's Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion - and, most importantly, without affecting your
sensitive hearing.
iii
Since hearing damage from loud sounds is often
undetectable until it is too late, YAMAHA and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
00_RXV750_U_EN.book Page 1 Tuesday, February 17, 2004 10:08 AM
CONTENTS
INTRODUCTION
INTRODUCTION
SOUND FIELD PROGRAMS
FEATURES............................................................. 2
GETTING STARTED............................................ 3
SOUND FIELD PROGRAM
DESCRIPTIONS...............................................45
Supplied accessories .................................................. 3
Installing batteries in the remote control ................... 3
For movie/video sources.......................................... 45
For music sources .................................................... 48
CONTROLS AND FUNCTIONS ......................... 4
PREPARATION
SPEAKER SETUP ............................................... 12
Speaker placement ................................................... 12
Speaker connections ................................................ 13
Before connecting components................................ 16
Connecting video components................................. 17
Connecting audio components................................. 20
Connecting the antennas .......................................... 22
Connecting the power supply cord .......................... 23
Turning on the power............................................... 25
AUTO SETUP....................................................... 26
Selecting the OSD mode.......................................... 49
Using the sleep timer ............................................... 49
Manually adjusting speaker levels........................... 50
Using the test tone ................................................... 51
SET MENU ............................................................52
Using SET MENU................................................... 53
1 SOUND MENU.................................................... 54
2 INPUT MENU...................................................... 58
3 OPTION MENU................................................... 60
REMOTE CONTROL FEATURES ...................62
Control area ............................................................. 62
Setting manufacturer codes...................................... 63
Controlling other components ................................. 65
Programming codes from other remote controls ..... 66
Changing source names in the display window....... 67
Clearing function sets .............................................. 68
Clearing individual functions .................................. 69
ZONE 2 (U.S.A., Canada and Australia
models only) .......................................................70
SOUND FIELD
PROGRAMS
Introduction.............................................................. 26
Optimizer microphone setup.................................... 26
Starting the setup ..................................................... 27
ADVANCED OPERATIONS ..............................49
BASIC
OPERATION
CONNECTIONS .................................................. 16
ADVANCED OPERATION
PREPARATION
Front panel ................................................................. 4
Remote control........................................................... 6
Using the remote control ........................................... 8
Front panel display .................................................... 9
Rear panel ................................................................ 11
Zone 2 connections .................................................. 70
Remote controlling Zone 2 ...................................... 71
BASIC OPERATION
PLAYBACK.......................................................... 31
Basic operations....................................................... 31
Selecting sound field programs ............................... 33
Selecting input modes.............................................. 37
Automatic and manual tuning.................................. 39
Presetting stations .................................................... 40
Selecting preset stations........................................... 42
Exchanging preset stations ...................................... 43
RECORDING ....................................................... 44
EDITING SOUND FIELD PARAMETERS ......73
What is a sound field ............................................... 73
Changing parameter settings ................................... 73
ADVANCED
OPERATION
TUNING ................................................................ 39
ADDITIONAL INFORMATION
SOUND FIELD PARAMETER
DESCRIPTIONS...............................................75
TROUBLESHOOTING .......................................79
RESETTING THE FACTORY PRESETS ........84
GLOSSARY...........................................................85
ADDITIONAL
INFORMATION
Audio formats .......................................................... 85
Sound field programs............................................... 86
Audio information ................................................... 86
Video signal information ......................................... 87
SPECIFICATIONS............................... Back cover
English
1
00_RXV750_U_EN.book Page 2 Tuesday, February 17, 2004 10:08 AM
FEATURES
FEATURES
Built-in 7-channel power amplifier
Other features
◆ Minimum RMS output power
(0.06% THD, 20 Hz – 20 kHz, 8Ω)
Front: 100 W + 100 W
Center: 100 W
Surround: 100 W + 100 W
Surround back: 100 W + 100 W
◆ YPAO: YAMAHA Parametric Room Acoustic
Optimizer for automatic speaker setup
◆ 192-kHz/24-bit D/A converter
◆ A SET MENU which provides you with items for
optimizing this unit for your audio/video system
◆ 8 additional input jacks for discrete multi-channel input
◆ PURE DIRECT for pure fidelity sound with analog and
PCM sources
◆ On-screen display function helpful in controlling this
unit
◆ S-Video signal input/output capability
◆ Component video input/output capability
◆ Video signal conversion (Composite video ↔ S-Video
→ Component video) capability for monitor out
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ Cinema and music night listening modes
◆ Remote control with preset manufacturer codes and
“learning” capability
◆ Zone 2 custom installation facility (U.S.A., Canada and
Australia models only)
Sound field features
◆ Proprietary YAMAHA technology for the creation of
sound fields
◆ Dolby Digital/Dolby Digital EX decoder
◆ DTS/DTS-ES Matrix 6.1, Discrete 6.1, DTS Neo:6,
DTS 96/24 decoder
◆ Dolby Pro Logic/Dolby Pro Logic II/Dolby Pro Logic
IIx decoder
◆ Virtual CINEMA DSP
◆ SILENT CINEMA™
Sophisticated AM/FM tuner
◆ 40-station random access preset tuning
◆ Automatic preset tuning
◆ Preset station shifting capability (preset editing)
• y indicates a tip for your operation.
• Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the double-D symbol
are trademarks of Dolby Laboratories.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
2
“DTS”, “DTS-ES”, “Neo:6” and “DTS 96/24” are trademarks of
Digital Theater Systems, Inc.
00_RXV750_U_EN.book Page 3 Tuesday, February 17, 2004 10:08 AM
GETTING STARTED
GETTING STARTED
INTRODUCTION
Supplied accessories
Please check that you received all of the following parts.
Remote control
TRANSMIT
RE-NAME
CLEAR
Batteries (4)
(AAA, R03, UM-4)
AM loop antenna
Optimizer microphone
LEARN
SYSTEM
POWER
STANDBY
SLEEP
INPUT MODE
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
SELECT
POWER
POWER
TV
AMP
AV
REC
AUDIO
Indoor FM antenna
(U.S.A., Canada, China,
Asia and General models)
DISC SKIP
VOL
FREQ/RDS
MODE
EON
PTY SEEK
START
SET MENU
LEVEL
TITLE
Indoor FM antenna
(Europe, Australia and
Korea models)
MUTE
MENU
TV VOL
TV INPUT
CH
A/B/C/D/E
TV MUTE
SELECT
CH
PRESET
PRESET
ON SCREEN
TEST
STRAIGHT
TV VOL
RETURN
DISPLAY
EFFECT
STEREO
HALL
JAZZ
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
9
0
10
ROCK
EX/ES
ENTER
CHP/INDEX
Installing batteries in the remote
control
2
1
3
Notes on batteries
• Change all of the batteries if you notice the following
conditions; the operation range of the remote control decreases,
the indicator does not flash or its light becomes dim.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
If the remote control is without batteries for more than
2 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
Press the
part and slide the battery
compartment cover off.
2
Insert four supplied batteries (AAA, R03,
UM-4) according to the polarity markings
(+ and –) on the inside of the battery
compartment.
3
Slide the cover back until it snaps into place.
English
1
3
00_RXV750_U_EN.book Page 4 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
CONTROLS AND FUNCTIONS
Front panel
1
2
3 4 5
6
7
8
9
0
(U.S.A. model)
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
EDIT
A/B/C/D/E
l PRESET/TUNING h
MEMORY
TUNING MODE
NEXT
LEVEL
MAN'L/AUTO FM
AUTO/MAN'L MONO
PROGRAM
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
TONE CONTROL
MULTI CH
INPUT
INPUT MODE
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
VIDEO
RDS MODE/FREQ
L
AUDIO
R
OPTICAL
EON
PTY SEEK
MODE
START
A
B
CD E F
G
H
I
J
K
LM NO
(Europe model only)
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When you
turn on this unit, you will hear a click and there will be a 4
to 5-second delay before this unit can reproduce sound.
Note
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
2 OPTIMIZER MIC jack
Use to connect and input audio signals from the supplied
microphone for use with the AUTO SETUP function (see
page 26).
3 Remote control sensor
Receives signals from the remote control.
4 Front panel display
Shows information about the operational status of this
unit.
5 A/B/C/D/E (NEXT)
Selects one of the 5 preset station groups (A to E) when
the unit is in tuner mode.
Selects the speaker channel to be adjusted when the unit is
not in tuner mode.
4
6 PRESET/TUNING l / h (LEVEL –/+)
Selects preset station number 1 to 8 when the colon (:) is
displayed next to the band indication in the front panel
display when the unit is in tuner mode. Selects the tuning
frequency when the colon (:) is not displayed.
Adjusts the level of the speaker channel selected using
A/B/C/D/E (NEXT) when the unit is not in tuner mode.
7 MEMORY (MAN’L/AUTO FM)
Stores a station in the memory. Hold down this button for
more than 3 seconds to start automatic preset tuning.
8 TUNING MODE (AUTO/MAN’L MONO)
Switches the tuning mode between automatic (AUTO
indicator on) and manual (AUTO indicator off).
9 VIDEO AUX jacks
Input audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select V-AUX as the input
source.
0 VOLUME
Controls the output level of all audio channels.
This does not affect the REC OUT level.
00_RXV750_U_EN.book Page 5 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
B SPEAKERS A/B
Turns on or off the set of front speakers connected to the A
and/or B terminals on the rear panel each time the
corresponding button is pressed.
C PRESET/TUNING (EDIT)
Switches the function of PRESET/TUNING l / h
(LEVEL –/+) between selecting preset station numbers
and tuning.
D STRAIGHT (EFFECT)
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
■ Europe model only
L RDS MODE/FREQ
Press this button when the unit is receiving an RDS station
to cycle the display between the PS mode, PTY mode, RT
mode, CT mode (if the station offers those RDS data
services) and/or the frequency display.
M PTY SEEK MODE
Press this button to set the unit to the PTY SEEK mode.
N PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
INTRODUCTION
A
PHONES (SILENT CINEMA) jack
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down
to the left and right headphone channels.
O EON
Press this button to select a radio program type (NEWS,
INFO, AFFAIRS, SPORT) to tune in automatically.
E FM/AM
Switches the reception band between FM and AM.
F PROGRAM
Use to select sound field programs or adjust the bass/treble
balance (in conjunction with TONE CONTROL).
G TONE CONTROL
Use to adjust the bass/treble balance for the front left and
right, center, presence and subwoofer channels (see
page 32).
H INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 37).
I INPUT selector
Selects the input source you want to listen to or watch.
J MULTI CH INPUT
Selects the source connected to the MULTI CH INPUT
jacks. When selected, the MULTI CH INPUT source takes
priority over the source selected with INPUT (or the input
selector buttons on the remote control).
K PURE DIRECT
Turns on or off PURE DIRECT mode (see page 36).
English
5
00_RXV750_U_EN.book Page 6 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
Remote control
This section describes the function of each control on the
remote control used to control this unit. To operate other
components, see “REMOTE CONTROL FEATURES” on
page 62.
1
2
3
TRANSMIT
RE-NAME
CLEAR
LEARN
SYSTEM
POWER
STANDBY
SLEEP
INPUT MODE
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
4
5
6
SELECT
POWER
POWER
TV
AV
AMP
REC
A
B
C
D
E
6 Display window
Shows the name of the selected source component that
you can control.
7 LEVEL
Selects the speaker channel to be adjusted and sets the
level.
8 Cursor buttons u / d / j / i / SELECT
Use to select and adjust sound field program parameters or
SET MENU items.
Press j / i to select preset station numbers when the unit is
in tuner mode.
G
Q
I
AUDIO
DISC SKIP
VOL
FREQ/RDS
MODE
7
8
PTY SEEK
0
START
SET MENU
TITLE
MUTE
MENU
TV VOL
TV INPUT
A/B/C/D/E
TV MUTE
SELECT
ON SCREEN
TEST
L
STRAIGHT
TV VOL
RETURN
J
K
CH
PRESET
PRESET
9
9 TEST (RETURN)
Outputs the test tone to adjust the speaker levels.
Returns to the previous menu level when adjusting the
SET MENU parameters.
EON
LEVEL
CH
4 SYSTEM POWER
Turns on the power of this unit.
5 Input selector buttons
Select the input source and change the control area.
F
H
3 STANDBY
Sets this unit in the standby mode.
DISPLAY
EFFECT
STEREO
HALL
JAZZ
ROCK
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
EX/ES
9
0
10
ENTER
CHP/INDEX
M
0 Sound field program / Numeric buttons (1 - 8)
Use to select sound field programs.
Use numbers 1 through 8 to select preset stations when the
unit is in tuner mode.
A RE-NAME
Use to change the input source name in the display
window (see page 67).
B CLEAR
Use to clear functions acquired when using the learn and
rename features, or setting manufacturer codes (see
page 68).
N
O
P
C LEARN
Use to set up manufacturer codes or program functions
from other remote controls (see pages 63 and 66).
D SLEEP
Sets the sleep timer.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 TRANSMIT indicator
Flashes while the remote control is sending signals.
6
E INPUT MODE
Sets the priority (AUTO, DTS, ANALOG) for the type of
signals received when one component is connected to two
or more of this unit’s input jacks (see page 37).
00_RXV750_U_EN.book Page 7 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
F MULTI CH IN
Selects MULTI CH INPUT when using an external
decoder (etc.).
■ Europe model only
G SELECT k/n
Selects another component that you can control
independently of the input component selected with the
input selector buttons.
FREQ/RDS
Press this button when the unit is receiving an RDS station
to cycle the display between the PS mode, PTY mode, RT
mode, CT mode (if the station offers those RDS data
services) and/or the frequency display.
I VOL –/+
Increases or decreases the volume level.
J MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level.
K SET MENU (A/B/C/D/E)
Activates the SET MENU function.
Selects preset station groups when the unit is in tuner
mode.
EON
Press this button to select a radio program type (NEWS,
INFO, AFFAIRS, SPORT) to tune in automatically.
INTRODUCTION
H AMP
Selects the AMP mode. You must select the AMP mode to
control the main unit.
Q RDS tuning buttons
PTY SEEK MODE
Press this button to set the unit to the PTY SEEK mode.
PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
L ON SCREEN
Selects the display mode of the on-screen display (OSD)
this unit sends to your video monitor.
M STRAIGHT (EFFECT)
Switches the sound fields off or on. When STRAIGHT is
selected, input signals (2-channel or multi-channel) are
output directly from their respective speakers without
effect processing.
N EX/ES
Switches between 5.1 or 6.1/7.1-channel playback of
multi-channel software.
O NIGHT
Turns on or off the night listening modes (see page 36).
P PURE DIRECT
Turns on or off PURE DIRECT mode (see page 36).
English
7
00_RXV750_U_EN.book Page 8 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
Using the remote control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
A/B/C/D/E
l PRESET/TUNING h
NEXT
EDIT
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
30
30
L
AUDIO
R
OPTICAL
Approximately 6 m (20 ft)
RE–NAME CLEAR LEARN
TRANSMIT
SYSTEM
POWER
VIDEO
STANDBY
SLEEP
INPUT MODE
CD
MULTI CH IN
PHONO
TUNER
V-AUX
CBL/SAT
MD/TAPE
DTV
VCR 1
DVR/VCR2
CD-R
DVD
SELECT
POWER
POWER
AMP
AV
TV
REC
AUDIO
DISC SKIP
VOL
LEVEL
SET MENU
TITLE
MENU
MUTE
TV VOL
TV INPUT
CH
A/B/C/D/E
TV MUTE
SELECT
PRESET
CH
PRESET
TEST
ON SCREEN
STRAIGHT
TV VOL
RETURN
DISPLAY
EFFECT
STEREO
HALL
JAZZ
1
2
3
ENTERTAIN
MUSIC
TV THTR
5
THX
9
6
/DTS
0
7
NIGHT
+10
ROCK
4
MOVIE
8
EX/ES
ENTER
CHP/INDEX
■ Handling the remote control
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity such as near a bath
– high temperature such as near a heater or stove
– extremely low temperatures
– dusty places
8
00_RXV750_U_EN.book Page 9 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
Front panel display
2
t
96
24
q EX
q PL
q PL
q PL x
DVR/VCR2
3
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
4
5
V-AUX
6
DTV/CBL
78
MD/CD-R
DVD
NIGHT ZONE2
90
TUNER
CD
E
PHONO
HiFi DSP
SLEEP
PS
TUNED STEREO MEMORY MUTE VOLUME
OPTIMIZER
PTY RT CT EON
dB
ft
mS
dB
D
B
PTY HOLD AUTO
PCM
C
A
H
F G
O (U.S.A., Canada and
Australia models only)
1 Decoder indicators
When any of this unit’s decoders function, the respective
indicator lights up.
2 SILENT CINEMA indicator
Lights up when headphones are connected and a sound
field program is selected (see page 32).
3 NIGHT indicator
Lights up when you select night listening mode.
4 Input source indicators
A cursor lights to show the current input source.
5 Sound field indicators
Light to indicate the active DSP sound fields.
Presence DSP sound field
Listening position
Left surround
DSP sound field
Right surround
DSP sound field
Surround back DSP sound field
6 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field
program.
7 AUTO indicator
Lights up when this unit is in automatic tuning mode.
8 TUNED indicator
Lights up when this unit is tuned into a station.
9 STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the AUTO indicator is lit.
96/24
L C R
LFE SL SB SR
J KLM
I
P
INTRODUCTION
1
N
(Europe model only)
0 MEMORY indicator
Blinks to show that a station can be stored.
A MUTE indicator
Blinks while the MUTE function is on.
B VOLUME level indication
Indicates the volume level.
C PCM indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
D VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 37).
E Headphones indicator
Lights up when headphones are connected.
F SP A B indicators
Light up according to the set of front speakers selected.
Both indicators light up when both sets of speakers are
selected.
G SLEEP indicator
Lights up while the sleep timer is on.
H HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program.
I Multi-information display
Shows the current sound field program name and other
information when adjusting or changing settings.
English
J OPTIMIZER indicator
Lights up during the auto setup procedure and when the
auto setup speaker settings are used without any
modifications.
9
00_RXV750_U_EN.book Page 10 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
K 96/24 indicator
Lights up when a DTS 96/24 signal is input to this unit.
L LFE indicator
Lights up when the input signal contains the LFE signal.
M Input channel indicators
Indicate the channel components of the current digital
input signal.
N Presence and surround back speaker
indicators
Indicate the connection of presence and/or surround back
speakers when using the SPEAKER LEVEL setting (see
page 56).
O ZONE 2 indicator
(U.S.A., Canada and Australia models only)
Lights up when Zone 2 power is on.
P RDS indicators
(Europe model only)
The name(s) of the RDS data offered by the currently
received RDS station light(s) up.
EON lights up when an RDS station that offers the EON
data service is being received.
PTY HOLD lights up while searching for stations in the
PTY SEEK mode.
10
00_RXV750_U_EN.book Page 11 Tuesday, February 17, 2004 10:08 AM
CONTROLS AND FUNCTIONS
Rear panel
2
3
4
COMPONENT VIDEO
PR
PB
6 7
8
TUNER
Y
75Ω UNBAL.
DVD
AUDIO
5
INTRODUCTION
1
FM
ANT
AUDIO
GND
AM
ANT
DTV
/CBL
PHONO
VIDEO
GND
DIGITAL
INPUT
VIDEO
S VIDEO
REMOTE
MONITOR
OUT
DVD
DVD
CD
ZONE 2
PRE OUT
CENTER
COAXIAL
IN
CD
OUT
OUT
IN
(REC)
VCR 1
FRONT
DVD
MD/CD-R
FRONT
SURROUND
SUB
WOOFER
SURROUND
SPEAKERS
IN
A
DVR/
VCR 2
SURROUND
B
OUT
MD/CD-R
OPTICAL
FRONT
SUB
WOOFER
CENTER
MULTI CH INPUT
ZONE 2
OUT
+12V
15mA MAX.
PRESENCE
/ZONE 2
SURROUND
BACK
OUT
SURROUND
BACK
DIGITAL
OUTPUT
SWITCHED
CONTROL
OUT
MD
/CD-R
OPTICAL
DTV/CBL
AC OUTLETS
IN
DTV
/CBL
(PLAY)
CENTER
SURROUND BACK
VIDEO
S VIDEO
MONITOR OUT
IMPEDANCE SELECTOR
(U.S.A. model)
9
0
A
B
C
D
1 DIGITAL INPUT jacks
See pages 17, 19 and 20 for details.
9 DIGITAL OUTPUT jack
See page 20 for details.
2 Audio component jacks
See page 20 for connection information.
0 MULTI CH INPUT jacks
See page 18 for connection information.
3 Video component jacks
See pages 17 and 19 for connection information.
A ZONE 2 OUTPUT jacks
(U.S.A., Canada and Australia models only)
See page 70 for details.
4 Antenna terminals
See page 22 for connection information.
5 PRESENCE/ZONE 2 speaker terminals
(U.S.A., Canada and Australia models)
PRESENCE speaker terminals
(other models)
See page 14 for connection information.
B PRE OUT jacks
See page 21 for connection information.
C Speaker terminals
See page 14 for connection information.
D IMPEDANCE SELECTOR switch
See page 24.
6 REMOTE IN/OUT jacks
(U.S.A., Canada and Australia models only)
See page 70 for details.
< Asia and General models only >
7 CONTROL OUT jack
(U.S.A., Canada and Australia models only)
This is a control expansion terminal for commercial use.
VOLTAGE SELECTOR
See page 23.
FREQUENCY STEP switch
See page 22.
English
8 AC OUTLET(S)
Use to supply power to your other A/V components (see
page 23).
11
00_RXV750_U_EN.book Page 12 Tuesday, February 17, 2004 10:08 AM
SPEAKER SETUP
SPEAKER SETUP
Surround speakers (SR and SL)
Speaker placement
The speaker layout below shows the standard ITU-R
speaker setting. You can use it to enjoy CINEMA DSP and
multi-channel audio sources.
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
Surround back speakers (SBR and SBL)
PL
PR
C
FR
FL
30˚
SL
SR
60˚
SL
80˚
SBL
SR
SBR
more than 30 cm (12 in)
The surround back speakers supplement the surround
speakers and provide for more realistic front-to-back
transitions. Place these speakers directly behind the
listening position and at the same height as the surround
speakers. They should be positioned at least 30 cm (12 in)
apart. Ideally, they should be positioned at the same width
as the front speakers.
Subwoofer
The use of a subwoofer, such as the YAMAHA Active
Servo Processing Subwoofer System, is effective not only
for reinforcing bass frequencies from any or all channels,
but also for high fidelity reproduction of the LFE (lowfrequency effect) channel included in Dolby Digital and
DTS software. The position of the subwoofer is not so
critical, because low bass sounds are not highly
directional. But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of the
room to reduce wall reflections.
Presence speakers (PR and PL)
1.8 m (6 ft)
1.8 m (6 ft)
Front speakers (FR and FL)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Align the front
face of the center speaker with the front face of your video
monitor. Place the speaker centrally between the front
speakers and as close to the monitor as possible, such as
directly over or under it.
12
Presence speakers supplement the sound from the front
speakers with extra ambient effects produced by CINEMA
DSP (see page 45). These effects include sounds that
filmmakers intend to locate a little farther back behind the
screen in order to create more theater-like ambience. Place
these speakers at the front of the room about 0.5 - 1 m
(1 - 3 ft) outside the front speakers, facing slightly
inwards, and about 1.8 m (6 ft) above the floor.
00_RXV750_U_EN.book Page 13 Tuesday, February 17, 2004 10:08 AM
SPEAKER SETUP
Speaker connections
5
Tighten the knob to secure the wire.
Be sure to connect the left channel (L), right channel (R),
“+” (red) and “–” (black) properly. If the connections are
faulty, no sound will be heard from the speakers, and if the
polarity of the speaker connections is incorrect, the sound
will be unnatural and lack bass.
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals on this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
4
5
Red: positive (+)
Black: negative (–)
■ Connecting to PRESENCE/ZONE 2 or
PRESENCE speaker terminals
2
1
2
3
1
Open the tab.
2
Insert one bare wire into the hole of each
terminal.
3
Return the tab to secure the wire.
10 mm (3/8")
1
PREPARATION
CAUTION
• If you will use 6 ohm speakers, be sure to set
this unit’s speaker impedance setting to 6
ohms before using (see page 24).
• Before connecting the speakers, make sure that the
power of this unit is off.
• Do not let the bare speaker wires touch each other or do
not let them touch any metal part of this unit. This
could damage this unit and/or speakers.
• Use magnetically shielded speakers. If this type of
speakers still creates the interference with the monitor,
place the speakers away from the monitor.
3
■ Banana plug connections
1
Remove approximately 10 mm (3/8") of
insulation from the end of each speaker
cable.
2
Twist the exposed wires of the cable together
to prevent short circuits.
(With the exception of U.K., Europe and Asia models)
First, tighten the knob and then insert the banana plug
connector into the end of the corresponding terminal.
Banana plug
3
Unscrew the knob.
4
Insert one bare wire into the hole in the side
of each terminal.
(With the exception of U.K., Europe
and Asia models)
y
You can also use banana plugs with the PRESENCE/ZONE 2 and
PRESENCE speaker terminals. Open the tab, then insert one
banana plug connector into the hole of each terminal. Do not
attempt to close the tabs after connecting the banana plugs.
English
13
00_RXV750_U_EN.book Page 14 Tuesday, February 17, 2004 10:08 AM
SPEAKER SETUP
Subwoofer
system
Presence speakers
Right
Left
1
2
3
Surround speakers
Right
Left
4
5
PRE OUT
CENTER
FRONT
SURROUND
SUB
WOOFER
PRESENCE
/ZONE 2
SURROUND
BACK
SPEAKERS
A
SURROUND
B
FRONT
CENTER
SURROUND BACK
(U.S.A. model)
6
7
Front
speakers
(B)
8
10
9
Center
speaker
Right
Left
Surround back
speakers
Right
Left
Front speakers (A)
You can connect both surround back and presence speakers to this unit, but they do not output sound simultaneously.
• The surround back speakers output the surround back channel included in Dolby Digital EX and DTS-ES software and only
operate when the Dolby Digital EX or DTS-ES decoder is turned on.
• The presence speakers output ambient effects created by the DSP sound fields. They do not output sound when other sound fields
are selected.
14
00_RXV750_U_EN.book Page 15 Tuesday, February 17, 2004 10:08 AM
SPEAKER SETUP
■ FRONT terminals
Connect one or two speaker systems to these terminals. If
you use only one speaker system, connect it to either the
FRONT A or B terminals.
Note
2
The Canada model cannot output to two separate speaker systems
simultaneously.
■ CENTER terminals
3
6
8
Connect a center speaker to these terminals.
7
1
PREPARATION
■ SURROUND terminals
4
Connect surround speakers to these terminals.
■ SUBWOOFER jack
Connect a subwoofer with built-in amplifier, such as the
YAMAHA Active Servo Processing Subwoofer System,
to this jack.
■ SURROUND BACK terminals
5
10
9
Speaker layout
Connect surround back speakers to these terminals. If you
only connect one surround back speaker, connect it to the
left (L) terminals.
■ PRESENCE terminals
Connect presence speakers to these terminals.
*
If you are using either the U.S.A., Canada or Australia model,
you can also use these speakers as Zone 2 speakers (see
page 61).
English
15
00_RXV750_U_EN.book Page 16 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
CONNECTIONS
Before connecting components
CAUTION
Do not connect this unit or other components to the mains
power until all connections between components are
complete.
Dust protection cap
Pull out the cap from the optical jack before you connect
the fiber optic cable. Do not discard the cap. When you are
not using the optical jack, be sure to put the cap back in
place. This cap protects the jack from dust.
■ Cable indications
■ Video jacks
For analog signals
left analog cables
L
right analog cables
R
For digital signals
optical cables
O
coaxial cables
C
For video signals
video cables
V
S-Video cables
S
This unit has three types of video jacks. Connection
depends on the availability of input jacks on your monitor.
The signals input through the S VIDEO jacks on this unit
are automatically converted for output through the VIDEO
jacks. When V CONV. is set to ON (see page 60), signals
input through the VIDEO jacks can be output through the
S VIDEO and COMPONENT VIDEO jacks. Likewise,
signals input through the S VIDEO jacks can also be
output through the COMPONENT VIDEO jacks.
VIDEO
S VIDEO
COMPONENT VIDEO
PR
PB
Y
V
V
■ Analog jacks
V
You can input analog signals from audio components by
connecting audio pin cable to the analog jacks on this unit.
Connect red plugs to the right jacks and white plugs to the
left jacks.
■ Digital jacks
This unit has digital jacks for direct transmission of digital
signals through either coaxial or fiber optic cables. You
can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. When you connect components to both
the COAXIAL and OPTICAL jacks, priority is given to
the input signals from the COAXIAL jack. All digital
input jacks are compatible with 96-kHz sampling digital
signals.
Note
This unit handles digital and analog signals independently. Thus
audio signals input to the analog jacks are only output to the
analog OUT (REC) jacks. Likewise audio signals input to the
digital (OPTICAL or COAXIAL) jacks are only output to the
DIGITAL OUTPUT jack.
VIDEO jack
For conventional composite video signals.
S VIDEO jack
For S-Video signals, separated into luminance (Y) and
color (C) video signals to achieve high-quality color
reproduction.
COMPONENT VIDEO jacks
For component signals, separated into luminance (Y) and
color difference (PB, PR) to provide the best quality in
picture reproduction.
Signal flow inside this unit
Input
Output
(MONITOR OUT)
COMPONENT
VIDEO
S VIDEO
VIDEO
Only when V CONV. is set to ON
(see page 60).
Note
When signals are input through both the S VIDEO and VIDEO
jacks, signals input through the S VIDEO jack have priority.
16
00_RXV750_U_EN.book Page 17 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
Connecting video components
■ Connections for DVD playback
Optical out
Coaxial out
Video out
DVD player
PREPARATION
Audio out
O
C
R
L
COMPONENT VIDEO
PR
PB
Y
DVD
AUDIO
VIDEO
VIDEO
DIGITAL
INPUT
DVD
S VIDEO
MONITOR
OUT
Video in
DVD
Video
monitor
COAXIAL
DVD
VIDEO
S VIDEO
MONITOR OUT
(U.S.A. model)
English
17
00_RXV750_U_EN.book Page 18 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
■ Connecting to the MULTI CH INPUT jacks
This unit is equipped with 8 additional input jacks (left and right FRONT, CENTER, left and right SURROUND, left and
right SURROUND BACK and SUB WOOFER) for discrete multi-channel input from a multi-format player, external
decoder, sound processor or pre-amplifier.
Connect the output jacks on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to
match the left and right outputs to the left and right input jacks for the front and surround channels.
For 6-channel input
For 8-channel input
(U.S.A. model)
(U.S.A. model)
FRONT
FRONT
SURROUND
SURROUND
SURROUND
BACK
SUB
WOOFER
SUB
WOOFER
CENTER
MULTI CH INPUT
R
L
Subwoofer
out
R
L
R
L
Center
out
Front
out
Multi-format player/
External decoder
CENTER
MULTI CH INPUT
Subwoofer
out
R
L
R
L
Center
out
Surround
out
Front
out
Multi-format player/ Surround
External decoder back out
Surround
out
Notes
• When you select MULTI CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you
cannot select sound field programs.
• This unit does not redirect signals input to the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that
you connect at least a 5.1-channel speaker system before using this feature.
• When headphones are used, only front left and right channels are output.
18
00_RXV750_U_EN.book Page 19 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
■ Connections for other video components
Optical out
Video out
Cable TV or
satellite tuner
Audio out
O
R
L
(U.S.A. model)
PREPARATION
COMPONENT VIDEO
AUDIO
DTV
/CBL
VIDEO
VIDEO
DIGITAL
INPUT
S VIDEO
DVD
DTV
/CBL
OPTICAL
DTV/CBL
IN
VCR 1
OUT
R
L
R
L
Audio in
Audio out
Video in
DVD recorder
or VCR
Video out
■ VIDEO AUX jacks (on the front panel)
Use these jacks to connect any video source, such as a
game console or video camera, to this unit.
VIDEO AUX
S VIDEO
VIDEO
L
S
V
L
AUDIO
R
OPTICAL
R
O
Optical out
Audio out R
Audio out L
S-Video out
19
English
Video out
Game
console or
video
camera
00_RXV750_U_EN.book Page 20 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
Connecting audio components
■ Connections for audio components
Turntable
GND
Audio out
R
AUDIO
L
AUDIO
PHONO
Audio out
CD player
GND
DIGITAL
INPUT
CD
L
R
Audio out
COAXIAL
IN
CD
(PLAY)
L
MD
/CD-R
OPTICAL
C
R
OUT
(REC)
L
Coaxial out
MD recorder or
tape deck
R
Audio in
Optical out
MD/CD-R
O
Optical in
O
MD/CD-R
OPTICAL
DIGITAL
OUTPUT
(U.S.A. model)
■ Connecting a turntable
y
PHONO jacks are for connecting a turntable with an MM
or high-output MC cartridge. If you have a turntable with
a low-output MC cartridge, use an in-line boosting
transformer or MC-head amplifier when connecting to
these jacks.
Connect your turntable to the GND terminal to reduce noise in
the signal. However you may hear less noise without the
connection to the GND terminal for some record players.
20
00_RXV750_U_EN.book Page 21 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
■ Connecting to an external amplifier
If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the PRE OUT jacks as follows.
Notes
1
23
PREPARATION
• When audio pin plugs are connected to the PRE OUT jacks for
output to an external amplifier, do not make connections to the
corresponding SPEAKERS terminals. Set the volume of the
amplifier connected to this unit to the maximum.
• The signals output through the FRONT PRE OUT and
CENTER PRE OUT jacks are affected by the TONE
CONTROL settings.
• If SPEAKERS A is turned off and SP B is set to ZONE B (see
page 61), signals will only be output from the FRONT PRE
OUT jacks.
4
PRE OUT
CENTER
L
R
FRONT
SURROUND
SUB
WOOFER
SURROUND
BACK
5
1 FRONT PRE OUT jacks
Front channel line output jacks.
2 SURROUND PRE OUT jacks
Surround channel line output jacks.
3 CENTER PRE OUT jack
Center channel line output jack.
4 SURROUND BACK PRE OUT jacks
Surround back or presence channel line output jacks.
5 SUB WOOFER PRE OUT jack
Connect a subwoofer with built-in amplifier, such as the
YAMAHA Active Servo Processing Subwoofer System,
to this jack.
Notes
• Each PRE OUT jack outputs the same channel signals as the
corresponding speaker terminals.
• Adjust the volume level of the subwoofer with the control on
the subwoofer. It is also possible to adjust the volume level
using the remote control (see “Manually adjusting speaker
levels” on page 50).
• Some signals may not be output from the SUB WOOFER PRE
OUT jack depending on the SPEAKER SET (see page 54) and
LFE/BASS OUT (see page 55) settings.
English
21
00_RXV750_U_EN.book Page 22 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
Connecting the antennas
Both AM and FM indoor antennas are included with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
Indoor FM antenna
(included)
AM loop antenna
(included)
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality, an
outdoor antenna may improve the quality. Consult the nearest
authorized YAMAHA dealer or service center about outdoor
antennas.
■ FREQUENCY STEP switch
(Asia and General models only)
TUNER
75Ω UNBAL.
FM
ANT
Notes
GND
AM
ANT
Because the interstation frequency
FREQUENCY STEP
spacing differs in different areas, set
AM
FM
the FREQUENCY STEP switch
(locating on the rear panel) according
to the frequency spacing in your area.
• North, Central and South America: 100 kHz/10 kHz
• Other areas: 50 kHz/9 kHz
Before setting this switch, disconnect this unit’s power
cord from the AC wall outlet.
10 KHZ / 100 KHZ
9 KHZ / 50 KHZ
Ground (GND terminal)
For maximum safety and minimum
interference, connect the antenna GND
terminal to a good earth ground. A good
earth ground is a metal stake driven into
moist earth.
■ Connecting the AM loop antenna
1
Set up the AM loop antenna, then connect it
to the terminals on this unit.
2
Press and hold the tab to
insert the AM loop antenna
lead wires into the AM ANT
and GND terminals.
3
Orient the AM loop antenna
for the best reception.
22
00_RXV750_U_EN.book Page 23 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
Connecting the power supply cord
■ Connecting the AC power cord
■ Memory back-up
Plug the power cord into an AC wall outlet.
The memory back-up circuit prevents the stored data from
being lost even if this unit is in the standby mode.
However if the power cord is disconnected from the AC
wall outlet, or the power supply is cut for more than one
week, the stored data will be lost.
■ AC OUTLET(S) (SWITCHED)
U.K. and Australia models ............................. 1 OUTLET
Korea model .............................................................. None
Other models ................................................. 2 OUTLETS
PREPARATION
Use these outlets to connect the power cords from your
other components to this unit. Power to the AC
OUTLET(S) is controlled by this unit’s STANDBY/ON
(or SYSTEM POWER and STANDBY). The outlet(s)
supply power to any connected component whenever this
unit is turned on. The maximum power (total power
consumption of components) that can be connected to the
AC OUTLET(S) is:
China, Asia and General models ............................. 50 W
Korea model ................................................................ N/A
Other models ........................................................... 100 W
■ VOLTAGE SELECTOR
(Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC main supply. Voltages are:
Asia model ......................... 220/230-240 V AC, 50/60 Hz
General model ...... 110/120/220/230-240 V AC, 50/60 Hz
VOLTAGE SELECTOR
VOLTAGE
SELECTOR
(Asia and General models)
English
23
00_RXV750_U_EN.book Page 24 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
■ IMPEDANCE SELECTOR switch
(U.S.A. model)
CAUTION
Do not change the setting of the IMPEDANCE
SELECTOR switch when the unit power is switched on,
as doing so may damage the unit.
If this unit fails to turn on when STANDBY/ON is pressed
on either the front panel or remote control, the
IMPEDANCE SELECTOR switch may not be fully slid to
either position. If this is the case, slide the switch all the
way to either position when this unit is in standby mode.
Select the switch position (left or right) according to the
impedance of the speakers in your system.
SET BEFORE POWER ON
IMPEDANCE SELECTOR
IMPEDANCE SELECTOR switch
Switch position
Speaker
Impedance level
If you use one set (A or B), the impedance of each speaker must be
4 Ω or higher.
Front
If you use two sets (A and B), the impedance of each speaker must be
8 Ω or higher.
Left
Center, Surround, Surround back,
Presence
The impedance of each speaker must be 6 Ω or higher.
If you use one set (A or B), the impedance of each speaker must be
8 Ω or higher.
Front
If you use two sets (A and B), the impedance of each speaker must be
16 Ω or higher.*
Right
Center, Surround, Surround back,
Presence
*
The impedance of each speaker must be 8 Ω or higher.
The Canada model cannot use two separate speaker systems (A and B) simultaneously when the switch is set to the right position.
24
00_RXV750_U_EN.book Page 25 Tuesday, February 17, 2004 10:08 AM
CONNECTIONS
Turning on the power
When all connections are complete, turn on the power of
this unit.
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
EDIT
A/B/C/D/E
l PRESET/TUNING h
NEXT
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
PREPARATION
(U.S.A. model)
1
TRANSMIT
RE-NAME
CLEAR
LEARN
SYSTEM
1
POWER
STANDBY
SLEEP
INPUT MODE
MULTI CH IN
A
B
PHONO
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
SELECT
POWER
POWER
TV
AV
AMP
REC
1
Press STANDBY/ON (SYSTEM POWER on the
remote control) to turn on the power of this
unit.
SYSTEM
STANDBY
/ON
Front panel
2
or
POWER
Remote control
Turn on the video monitor connected to this
unit.
English
25
00_RXV750_U_EN.book Page 26 Tuesday, February 17, 2004 10:08 AM
AUTO SETUP
AUTO SETUP
Introduction
This receiver employs YAMAHA Parametric Room
Acoustic Optimizer (YPAO) technology which lets you
avoid troublesome listening-based speaker setup and
achieves highly accurate sound adjustments. The supplied
optimizer microphone collects and analyzes the sound
your speakers produce in your actual listening
environment.
Optimizer microphone setup
1
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
(U.S.A. model)
Notes
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
EDIT
A/B/C/D/E
l PRESET/TUNING h
NEXT
LEVEL
PROGRAM
• Please be advised that it is normal for loud test tones to be
output during the auto setup procedure.
• If auto setup stops and error messages appear on the screen,
follow the troubleshooting on page 30.
MEMORY
TU
MAN'L/AUTO FM
A
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
TONE CONTROL
INPUT MODE
Y
EFFECT
SILENT CINEMA
YPAO performs the following checks and makes
appropriate adjustments to give you the best possible
sound from your system.
WIRING/LEVEL:
Checks which speakers are connected and the polarity of
each speaker. Also checks and adjusts the sound level
(volume) of each speaker so that the sound level of each
speaker is the same when heard from the listening
position.
DISTANCE/PHASE:
Checks the distance of each speaker from the listening
position and adjusts the delay of each channel so that the
sound from each speaker reaches the listening position at
the same time. Also checks the phase of each speaker.
SIZE:
Checks the speakers frequency response and sets the
crossover/high cut frequency for the subwoofer to improve
the sound relationship between the speakers and the
subwoofer.
26
Notes
• After you have completed the auto setup procedure, be sure to
disconnect the optimizer microphone.
• The optimizer microphone is sensitive to heat.
– Keep it away from direct sunlight.
– Do not place it on top of this unit.
2
Place the optimizer microphone on a flat
level surface with the omni-directional
microphone head upward, at your normal
listening position.
If possible, use a tripod (etc.) to affix the optimizer
mic at the same height as your ears would be when
you are seated in your listening position.
Optimizer microphone position
00_RXV750_U_EN.book Page 27 Tuesday, February 17, 2004 10:08 AM
AUTO SETUP
Starting the setup
6
For best results, make sure the room is as quiet as possible
during the auto setup procedure (YPAO). If there is too
much ambient noise, the results may not be satisfactory.
Press u / d to select SETUP, then press j / i
to select the desired setting.
1 AUTO:MENU
y
p
If your subwoofer has adjustable volume and crossover/high cut
frequency controls, set the volume between 9 and 11 o’clock (as
viewed on a conventional clockface) and set the crossover/high
cut frequency to the maximum.
CROSSOVER/
HIGH CUT
VOLUME
RELOAD
MIN
MAX
MAX
MIN
Subwoofer
UNDO
1
Switch on this unit and your video monitor.
Make sure the OSD is displayed.
2
Press AMP.
DEFAULT
y
You can choose RELOAD or UNDO only if you have
already performed auto setup.
AMP
7
3
Press SET MENU.
SET MENU
MENU
A/B/C/D/E
4
To perform the auto setup procedure
(YPAO).
To reload the last auto setup (YPAO)
settings to override any manual
changes.
To undo the last auto setup (YPAO) and
restore the previous settings.
To restore the factory preset (default)
setup parameters.
PREPARATION
AUTO
p
. SETUP;;;;;;;AUTO
START
Automatic
processing
of all items
[ ]/[ ]:Up/Down
[<]/[>]:Select
Press d to select START, then press SELECT
to start the setup procedure.
• If you selected AUTO in step 6, loud test tones will
be output from each speaker in turn; WAIT appears
during the auto setup procedure.
• If you selected DEFAULT, RELOAD or UNDO in
step 6, no test tones are output.
Press u / d to select AUTO SETUP.
1 AUTO:MENU
+
SET MENU
TV VOL
CH
TV MUTE
SELECT
–
PRESET
.;AUTOSETUP
;MANUALSETUP
CH
+
PRESET
p
p
–
p
p
[ ]/[ ]:Up/Down
[SELECT]:Enter
TV VOL
SETUP;;;;;;;AUTO
.START
Automatic
processing
of all items
[]/[]:Up/Down
[SELECT]:Start
The RESULT:WIRING screen appears after all items
have been measured and set.
5
Press SELECT to enter AUTO SETUP.
RESULT:WIRING
FRONTL;;;;;;;OK
+
TV VOL
CH
–
TV MUTE
SELECT
PRESET
CH
+
PRESET
TV VOL
[<]/[>]:Select
[SELECT]:Return
–
27
English
• If an ERROR screen appears, see “If an error
screen appears” on page 28.
• If a WARNING screen appears, see “If a warning
screen appears” on page 29.
00_RXV750_U_EN.book Page 28 Tuesday, February 17, 2004 10:08 AM
AUTO SETUP
■ If an error screen appears
8
Use the cursor buttons to display the results.
• Press u / d to display information about
individual results.
• Press j / i to switch between each result list.
1
Press SELECT to display detailed
information about the error.
ERROR
RESULT:WIRING
.E-5:NOISY
FRONTL;;;;;;;OK
2
9
When finished, press SELECT.
The RESULT:EXIT screen appears.
10
Press u / d to select SET or CANCEL.
p
p
)RETRYEXIT
[]/[]:Up/Down
[SELECT]:Enter
[<]/[>]:Select
[SELECT]:Return
Press j / i to switch between error
messages.
For details about each message, see page 30.
ERROR: E-5
<
NOISY
>
RESULT:EXIT
Keep
SILENT
SET
CANCEL
11
[SELECT]:Return
p
p
NOWARNING
RESULTLIST
.)SETCANCEL
[]/[]:Up/Down
[SELECT]:Enter
To apply the auto setup (YPAO)
settings.
To cancel the auto setup (YPAO)
without making any changes.
3
When finished, press SELECT to return to
the main error screen.
4
Press u / d to select RETRY or EXIT, then
press SELECT.
Press SELECT to set or cancel the auto
setup settings.
ERROR
E-5:NOISY
y
If you are not satisfied with the result or want to manually adjust
each setup parameter, use the manual setup parameters (see
page 52).
28
RETRY
EXIT
p
• If E-10 appears during testing, restart the procedure from step 3.
• To cancel the auto setup procedure before completion, press
SET MENU.
p
Notes
.)RETRY
EXIT
[
]/[
]:Up/Down
[SELECT]:Enter
To retry the auto setup procedure.
To exit auto setup.
00_RXV750_U_EN.book Page 29 Tuesday, February 17, 2004 10:08 AM
AUTO SETUP
■ If a warning screen appears
1
Press j / i to display detailed information
about each warning.
For details about each message, see page 30.
WARNING:W-1
PREPARATION
<OUTOFPHASE>
ReverseChannel
FLFR
----------[<]/[>]:Select
[SELECT]:Return
y
Warnings let you know about potential problems detected
during auto setup. Warnings will not cancel the auto setup.
2
When you are finished, press SELECT.
The RESULT:EXIT screen appears.
3
Press u / d to select RESULT LIST, then
press SELECT.
RESULT:EXIT
WARNINGLIST
.RESULTLIST
p
p
)SETCANCEL
[]/[]:Up/Down
[SELECT]:Enter
The RESULT:WIRING screen appears.
RESULT:WIRING
FRONTL;;;;;REV.
[<]/[>]:Select
[SELECT]:Return
Continue from step 8 on page 28 to display
each result.
Notes
• If you change speakers, speaker positions, or the layout of your
listening environment, perform auto setup again to re-calibrate
your system.
• If SWFR PHASE:REV appears in RESULT:WIRING, the SET
MENU “SUBWOOFER PHASE” parameter is automatically
set to REVERSE (see page 56).
• In the DISTANCE results, the distance displayed may be longer
than the actual distance depending on the characteristics of your
subwoofer.
English
29
00_RXV750_U_EN.book Page 30 Tuesday, February 17, 2004 10:08 AM
AUTO SETUP
■
Troubleshooting for auto setup procedure
Before auto setup
Error message
Cause
Remedy
Connect MIC!
Optimizer microphone is not connected.
• Connect the supplied optimizer microphone to the
OPTIMIZER MIC jack on the front panel.
Unplug HP!
Headphones are connected.
• Unplug the headphones.
Errors during auto setup
Press SELECT to display detailed information about individual errors. Press j / i to switch between error messages.
Error message
Cause
Remedy
E-1:NO FRONT SP
Front L/R channel signal(s) is (are) not
detected.
• Select the front speakers with SPEAKER A or B.
• Check the front left and right speaker connections.
E-2:NO SURR.SP
A surround channel signal is not detected.
• Check the surround speaker connections.
E-3:NO PRES. SP
A presence channel signal is not detected.
• Check the presence speaker connections.
E-4:SBR->SBL
Only right surround back channel signal is
detected.
• Connect the surround back speaker to the LEFT
SURROUND BACK SPEAKERS terminal if you
only have one surround back speaker.
E-5:NOISY
Background noise is too loud.
• Try the auto setup procedure in a quiet environment.
• Turn off noisy electric equipment like air conditioners
(etc.) or move them away from the optimizer
microphone.
E-6:CHECK SURR.
Surround back speaker(s) is (are) connected,
though surround L/R speakers are not.
• Connect surround speakers when you use (a)
surround back speaker(s).
E-7:NO MIC
The optimizer microphone was unplugged
during the auto setup procedure.
• Do not touch the optimizer microphone during the
auto setup procedure.
E-8:NO SIGNAL
The optimizer microphone does not detect test
tones.
• Check the microphone setting.
• Check the speaker connections and placement.
E-9:USER CANCEL
The auto setup procedure was cancelled due to
user activity.
• Perform the auto setup procedure again. Do not adjust
VOLUME (etc.) during the auto setup procedure.
E-10:OTHER ERROR
A DSP communication error or hangup
occurred.
• Perform the auto setup procedure again.
Warnings after auto setup
Press j / i to display detailed information about individual warnings.
Warning message
•
•
•
•
Cause
Remedy
W-1:OUT OF PHASE
Speaker polarity is not correct. This message
may appear depending on the speakers even
when the speakers are connected correctly.
• Check the speaker connections for proper polarity
(+ or –).
W-2:OVER 24m
(80ft)
The distance between the speaker and the
listening position is over 24 m (80 ft).
• Bring the speaker closer to the listening position.
W-3:LEVEL ERROR
The difference of volume level among speakers
is excessive. (No level correction is made.)
• Readjust the speaker installation so that all speakers
are set in locations with similar conditions.
• Check the speaker connections.
• Use speakers of similar quality and efficiency.
• Adjust the output volume of the subwoofer.
If the ERROR or WARNING screens appears, check the cause of the problem, then perform the auto setup procedure again.
If warning W-1 appears, corrections are made, but they may not be optimal.
If warning W-2 or W-3 appears, no corrections are made.
If error E-10 occurs repeatedly, please contact a qualified YAMAHA service center.
30
00_RXV750_U_EN.book Page 31 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
PLAYBACK
Basic operations
4
(U.S.A. model)
Select the input source.
Use INPUT (or press one of the input selector buttons
on the remote control) to select the input you desire.
INPUT
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
VOLUME
or
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
l PRESET/TUNING h
A/B/C/D/E
NEXT
EDIT
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
1
3
7
VIDEO
CLEAR
SLEEP
INPUT MODE
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
MODE
4
EON
PTY SEEK
TITLE
DVR/VCR2
VCR-1
MUTE
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
TUNER
PTY HOLD AUTO
HiFi DSP
PS
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
10 D VD D AUTOO00
dB
ft
mS
dB
96/24
L C R
LFE SL SB SR
MENU
A/B/C/D/E
TV MUTE
SELECT
Selected input source
CH
Input mode
PRESET
PRESET
ON SCREEN
TEST
STRAIGHT
TV VOL
SELECT
RETURN
DISPLAY
EFFECT
POWER
POWER
TV
AV
STEREO
HALL
JAZZ
ROCK
AMP
REC
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
9
0
10
7
5
Start playback or select a broadcast station
on the source component.
Refer to the operating instructions for the component.
6
Adjust the volume to the desired output level.
EX/ES
ENTER
CHP/INDEX
1
q PL
TV VOL
TV INPUT
CH
7
96
24
q EX
q PL
q PL x
PCM
START
SET MENU
LEVEL
t
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
VOL
FREQ/RDS
BASIC
OPERATION
STANDBY
Remote control
The current input source name and input mode appear
in the front panel display and video monitor for a few
seconds.
6
DISC SKIP
SYSTEM
POWER
Front panel
OPTICAL
AV
LEARN
AUDIO
1
R
6
TV
RE-NAME
AUDIO
4
REC
TRANSMIT
L
Press STANDBY/ON (SYSTEM POWER on the
remote control) to turn on the power.
VOLUME
SYSTEM
STANDBY
/ON
+
POWER
or
or
Front panel
–
Remote control
2
Turn on the video monitor connected to this
unit.
3
Press SPEAKERS A or B on the front panel.
Each press turns the respective speakers on or off.
VOL
Front panel
Remote control
SPEAKERS
B
A
English
31
00_RXV750_U_EN.book Page 32 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
7
Select a sound field program if desired.
Use PROGRAM (or press AMP to select the AMP
mode, then press one of the sound field program
buttons repeatedly) to select a sound field program.
See page 45 for details about sound field programs.
PROGRAM
AMP
or
Front panel
STEREO
HALL
JAZZ
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
9
0
10
ROCK
EX/ES
ENTER
CHP/INDEX
Remote control
To adjust the tone
You can adjust the tonal quality
TONE CONTROL
of your front left and right,
center, presence and subwoofer
speakers or headphones (when
connected).
Press TONE CONTROL on the
PROGRAM
front panel repeatedly to select
TREBLE or BASS, then rotate
PROGRAM to the right or left to
increase or decrease.
• Select TREBLE to adjust the
high frequency response.
• Select BASS to adjust the low frequency response.
To cancel the tone control, press TONE CONTROL
repeatedly to select BYPASS.
y
Speaker and headphone adjustments are stored independently.
Note
To listen with headphones (SILENT CINEMA)
“SILENT CINEMA” allows you to enjoy multi-channel
music or movie sound, including Dolby Digital and DTS
surround, through ordinary headphones. “SILENT
CINEMA” activates automatically whenever you connect
headphones to the PHONES jack while listening to
CINEMA DSP or HiFi DSP sound field programs. When
activated, the “SILENT CINEMA” indicator lights up in
the front panel display.
Notes
• This unit will not be set to “SILENT CINEMA” when MULTI
CH INPUT is selected as the input source.
• “SILENT CINEMA” is not effective when PURE DIRECT or
the 2ch Stereo program is selected, or in STRAIGHT mode.
32
TONE CONTROL is not effective during playback in the PURE
DIRECT mode, or when MULTI CH INPUT is selected
(page 36).
To mute the sound
Press MUTE on the remote control.
The MUTE indicator blinks in the
front panel display.
To resume the audio output, press
MUTE again (or press VOL –/+).
The MUTE indicator disappears
from the display.
y
You can adjust the muting level (see page 57).
MUTE
00_RXV750_U_EN.book Page 33 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
■ Selecting MULTI CH INPUT
Press MULTI CH INPUT so that “MULTI CH INPUT”
appears in the front panel display and video monitor.
MULTI CH
INPUT
Selecting sound field programs
■ Front panel operation
MULTI CH IN
or
VOLUME
Front panel
Remote control
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
A/B/C/D/E
l PRESET/TUNING h
NEXT
LEVEL
EDIT
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
MULTI CH INPUT
VIDEO
L
AUDIO
R
OPTICAL
(U.S.A. model)
PROGRAM
Note
When “MULTI CH INPUT” is shown in the front panel display,
no other source can be played. To select another input source with
INPUT (or one of the input selector buttons), press MULTI CH
INPUT to turn off “MULTI CH INPUT” in the front panel
display.
Rotate PROGRAM to select the desired program.
The name of the selected program appears in the front
panel display and video monitor.
PROGRAM
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Use the input selector buttons on the remote
control to select a video source, then select an
audio source.
PHONO
BASIC
OPERATION
■ Playing video sources in the
background
t
96
24
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q EX
q PL
q PL
q PL x
PCM
V-AUX
DTV/CBL
SLEEP
MD/CD-R
DVD
NIGHT ZONE2
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
10 DJAZZACLUBO00
dB
ft
mS
dB
96/24
L C R
LFE SL SB SR
Program name
MULTI CH IN
A
B
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
Audio sources
Video sources
Note
If you want to enjoy audio from the MULTI CH INPUT jacks
together with a video source, first select the video source, then
press MULTI CH INPUT.
English
33
00_RXV750_U_EN.book Page 34 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
■ Remote control operation
■ Enjoying multi-channel software
SET MENU
LEVEL
TITLE
If you connected a surround back speaker, use this feature
to enjoy 6.1/7.1-channel playback for multi-channel
sources using the Dolby Pro Logic IIx, Dolby Digital
Surround EX or DTS-ES decoders.
MUTE
MENU
TV VOL
TRANSMIT
RE-NAME
CLEAR
TV INPUT
LEARN
SYSTEM
POWER
STANDBY
SLEEP
INPUT MODE
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
A/B/C/D/E
CH
CH
TV MUTE
SELECT
PRESET
PRESET
TEST
ON SCREEN
STRAIGHT
TV VOL
RETURN
DISPLAY
EFFECT
STEREO
HALL
JAZZ
2
3
4
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
9
0
POWER
POWER
TV
AV
Sound field
program
buttons
EX/ES
ENTER
10
CHP/INDEX
SELECT
AMP
ROCK
1
MUSIC
Press AMP to select the AMP mode, then press
EX/ES on the remote control to switch between
5.1 and 6.1/7.1-channel playback.
AMP
EX/ES
REC
ENTER
AUDIO
CHP/INDEX
Press AMP to select the AMP mode, then press
one of the sound field program buttons
repeatedly to select the desired program.
The name of the selected program appears in the front
panel display.
To select a decoder, press j / i repeatedly when
PLIIxMusic (etc.) is displayed.
+
TV VOL
STEREO
HALL
JAZZ
ROCK
CH
1
2
3
4
–
MUSIC
ENTERTAIN
TV THTR
MOVIE
PRESET
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
EX/ES
9
0
AMP
TV MUTE
SELECT
CH
+
PRESET
TV VOL
–
ENTER
10
CHP/INDEX
t
96
24
q EX
q PL
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q PL
q PL x
PCM
V-AUX
DTV/CBL
SLEEP
MD/CD-R
DVD
NIGHT ZONE2
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
10 DJAZZACLUBO00
dB
ft
mS
dB
96/24
L C R
LFE SL SB SR
Program name
y
Choose a sound field program based on your listening preference,
and not on the name of the program.
Notes
• When you select an input source, this unit automatically selects
the last sound field program used with that source.
• Sound field programs cannot be selected when MULTI CH
INPUT is selected.
• Sampling frequencies higher than 48 kHz (except for DTS 96/
24 signals) will be sampled down to 48 kHz, then sound field
programs will be applied.
AUTO (AUTO)
When a signal (flag) that can be recognized by the unit is
input, the unit selects the optimum decoder for playing
back the signal in 6.1/7.1 channels.
If the unit cannot recognize the flag or no flag is present in
the input signal, it cannot automatically be played in 6.1/
7.1 channels.
Decoders (select with j / i)
You can select from the following decoders depending on
the format of the software you are playing.
PLIIxMovie
For playing back Dolby Digital or DTS signals in 6.1/7.1
channels using the Pro Logic IIx movie decoder.
PLIIxMusic
For playing back Dolby Digital or DTS signals in 6.1/7.1
channels using the Pro Logic IIx music decoder.
EX/ES
For playing back Dolby Digital signals in 6.1/7.1 channels
using the Dolby Digital Surround EX decoder.
DTS signals are played back in 6.1/7.1 channels using the
DTS-ES decoder.
EX
For playing back Dolby Digital or DTS signals in 6.1/7.1
channels using the Dolby Digital Surround EX decoder.
OFF (OFF)
Decoders are not used to create 6.1/7.1 channels.
y
When “SURR B L/R SP” is set to SMLx1 or LRGx1 (see
page 55), the surround back channel will be output from the left
SURROUND BACK speaker terminals.
34
00_RXV750_U_EN.book Page 35 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
Notes
Signals input from 2-channel sources can also be played
back on multiple channels.
Press q/DTS on the remote control to select the
decoder.
/DTS
9
You can select from the following decoders depending on
the type of software you are playing and your personal
preference.
PRO LOGIC SUR. STANDARD
Standard processing for Dolby Surround sources.
PRO LOGIC SUR. ENHANCED
CINEMA DSP enhanced processing for Dolby Surround
sources.
PRO LOGIC IIx Movie*
Dolby Pro Logic II/IIx processing for movie software.
BASIC
OPERATION
• Some 6.1-channel compatible discs do not have a signal (flag)
which this unit can automatically detect. When playing these
kinds of discs with 6.1-channel, select a decoder (PLIIx Movie,
PLIIx Music, EX/ES or EX) manually.
• 6.1-channel playback is not possible even if EX/ES is pressed in
the following cases:
– When “SURR L/R SP” (see page 54) or “SURR B L/R SP”
(see page 55) is set to NONE.
– When the source connected to the MULTI CH INPUT jack is
being played.
– When the source being played does not contain surround left
and right channel signals.
– When a Dolby Digital KARAOKE source is being played.
– When “2ch Stereo” or PURE DIRECT is selected.
• When the power of this unit is turned off, the input mode will be
reset to AUTO.
• When the DTS-ES decoder is applied to DTS 96/24 signals, you
cannot use the DTS 96/24 decoding feature.
• The Pro Logic IIx decoder is not available when “SURR B L/R
SP” is set to NONE (see page 55).
• PLIIxMovie cannot be selected when “SURR B L/R SP” is set
to SMLx1 or LRGx1 (see page 55).
■ Enjoying 2-channel software
PRO LOGIC IIx Music*
Dolby Pro Logic II/IIx processing for music software.
PRO LOGIC IIx Game*
Dolby Pro Logic II/IIx processing for game software.
DTS Neo:6 Cinema
DTS processing for movie software.
DTS Neo:6 Music
DTS processing for music software.
*
Use the PLII/PLIIx parameter to select the Pro Logic II or Pro
Logic IIx decoders (see page 78).
Note
The Pro Logic IIx decoder is not available when “SURR B L/R
SP” is set to NONE (see page 55).
English
35
00_RXV750_U_EN.book Page 36 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
■ Listening to high fidelity stereo sound
(PURE DIRECT)
PURE DIRECT allows you to bypass this unit’s decoders
and DSP processors, and turn off the video circuitry and
front panel display to enjoy pure high fidelity sound from
analog and PCM sources.
Press PURE DIRECT to activate pure direct.
The indicator around the front panel button lights up.
PURE DIRECT
or
Front panel
■ Night listening modes
The night listening modes are designed to improve
listenability at lower volumes or at night. Choose either
NIGHT:CINEMA or NIGHT:MUSIC depending on the
type of material you are playing.
Press NIGHT on the remote control repeatedly to
select cinema or music.
When night listening is selected, the NIGHT indicator in
the front panel display lights up.
PURE DIRECT
NIGHT
0
+10
Remote control
Remote control
y
The front panel display switches on momentarily when an
operation is performed.
To cancel, press PURE DIRECT again.
The indicator around the front panel button goes out and
the previous settings are restored.
Notes
• To avoid unexpected noise, do not play DTS-encoded CDs in
this mode.
• When a multi-channel signal (Dolby Digital or DTS) is input,
this unit automatically switches to the corresponding analog
input.
• No sound will be output from the subwoofer.
• The following operations are not possible during PURE
DIRECT operation:
– switching the sound field program
– displaying the OSD
– adjusting SET MENU parameters
– all video functions (video conversion etc.)
• PURE DIRECT is automatically cancelled whenever this unit is
set to the standby mode.
• Select NIGHT:CINEMA when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select NIGHT:MUSIC when listening to music sources
to preserve ease-of-listening for all sounds.
• Select OFF if you do not want to use this function.
Press j / i to adjust the effect level while
NIGHT:CINEMA or NIGHT:MUSIC is displayed.
This adjusts the level of compression.
+
TV VOL
CH
–
TV MUTE
SELECT
PRESET
CH
+
PRESET
TV VOL
–
Remote control
Effect.Lvl:MID
• Select MIN for minimum compression.
• Select MID for standard compression.
• Select MAX for maximum compression.
y
NIGHT:CINEMA and NIGHT:MUSIC adjustments are stored
independently.
Notes
• You cannot use the night listening modes with PURE DIRECT
or MULTI CH INPUT (even though the NIGHT indicator lights
up when PURE DIRECT is selected).
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
36
00_RXV750_U_EN.book Page 37 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
■ Downmixing to 2 channels
You can enjoy 2-channel stereo playback even from multichannel sources.
Rotate PROGRAM (or press STEREO on the
remote control) to select 2ch Stereo.
PROGRAM
STEREO
or
HALL
JAZZ
ROCK
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
EX/ES
9
0
Selecting input modes
This unit comes with a variety of input jacks. Do the
following to select the type of input signals you want to
use.
1
Rotate INPUT to select the input source.
INPUT
ENTER
10
CHP/INDEX
Remote control
Front panel
2
2ch Stereo
Press INPUT MODE to select an input mode.
In most cases, use AUTO.
y
INPUT MODE
You can use a subwoofer with this program when SWFR or
BOTH is selected in “BASS OUT”.
In STRAIGHT mode, two channel stereo sources are
output from only the front left and right speakers. Multichannel sources are decoded straight into the appropriate
channels without any additional effect processing.
t
96
24
q EX
q PL
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q PL
q PL x
PCM
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
10 D VD D AUTOO00
dB
ft
mS
dB
96/24
BASIC
OPERATION
■ Listening to unprocessed input signals
L C R
LFE SL SB SR
Press STRAIGHT (EFFECT) to select STRAIGHT.
Input source
STRAIGHT
STRAIGHT
or
AUTO
EFFECT
EFFECT
Front panel
Remote control
DTS
STRAIGHT
ANALOG
Press STRAIGHT (EFFECT) again so that “STRAIGHT”
disappears from the display when you want to turn the
sound effect back on.
Automatically selects input signals in
the following order:
1) Digital signals*
2) Analog signals
Selects only digital signals encoded in
DTS. If no DTS signals are input, no
sound is output.
Selects only analog signals. If no
analog signals are input, no sound is
output.
* If this unit detects a Dolby Digital or DTS signal, the
decoder automatically switches to the appropriate sound
field program.
■ Virtual CINEMA DSP
Virtual CINEMA DSP allows you to enjoy the CINEMA
DSP programs without surround speakers. It creates
virtual speakers to reproduce the natural sound field.
If you do not connect surround speakers, Virtual CINEMA
DSP activates automatically whenever you select a
CINEMA DSP sound field program.
Input mode
y
You can adjust the default input mode this unit selects when the
power is turned on (see page 59).
Note
English
Virtual CINEMA DSP will not activate, even when “SURR L/R
SP” is set to NONE (see page 54) in the following cases:
– When MULTI CH INPUT is selected as the input source.
– When headphones are connected to the PHONES jack.
37
00_RXV750_U_EN.book Page 38 Tuesday, February 17, 2004 10:08 AM
PLAYBACK
Notes
3
• When you play DTS-encoded CD/LDs with the input mode set
to AUTO:
– This unit automatically switches to the DTS decoding mode.
The unit remains in DTS mode (and the t indicator may
flash) for up to 30 seconds after playback of the DTS source is
complete. To manually release the DTS mode, press INPUT
MODE to reselect AUTO.
– The DTS decoding mode may be released if search or skip
operations are performed for more than 30 seconds. To
prevent this, press INPUT MODE to select DTS.
• If the digital output data of the player has been processed in any
way, you may not be able to perform DTS decoding even if you
make a digital connection between this unit and the player.
Displaying information about the input
source
Press u / d to display the following
information about the input signal.
+
TV VOL
CH
–
2
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
(Format)
in
rate
Press AMP to select the AMP mode, then
press STRAIGHT (EFFECT) so that
“STRAIGHT” appears in the display.
STRAIGHT
AMP
then
EFFECT
STRAIGHT
38
+
–
fs
Select the input source.
CH
PRESET
TV VOL
You can display the type, format and sampling frequency
of the current input signal.
1
TV MUTE
SELECT
PRESET
flg
Signal format display. When the unit
cannot detect a digital signal it
automatically switches to analog input.
Number of source channels in the input
signal. For example, a multi-channel
soundtrack with 3 front channels, 2
surround channels and LFE, is
displayed as “3/2/LFE”.
Sampling frequency. When the unit is
unable to detect the sampling
frequency “Unknown” appears.
Bit rate. When the unit is unable to
detect the bit rate “Unknown” appears.
Flag data encoded with DTS or Dolby
Digital signals that cue this unit to
automatically switch decoders.
00_RXV750_U_EN.book Page 39 Tuesday, February 17, 2004 10:08 AM
TUNING
TUNING
Automatic and manual tuning
3
There are 2 tuning methods; automatic and manual.
Automatic tuning is effective when station signals are
strong and there is no interference.
TUNING MODE
■ Automatic tuning
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
VOLUME
PRESET/TUNING
FM/AM
l PRESET/TUNING h
A/B/C/D/E
NEXT
EDIT
AUTO
Lights up
AUTO/MAN'L MONO
(U.S.A. model)
OPTIMIZER
MIC
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator lights up in the
front panel display.
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
PRESET/TUNING
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EDIT
EFFECT
SILENT CINEMA
S VIDEO
4
1
L
AUDIO
R
OPTICAL
3
R/VCR2
VCR-1
T CINEMA
SP
TUAL
V-AUX
DTV/CBL
MD/CD-R
DVD
NIGHT ZONE2
AB
PTY HOLD AUTO
HiFi DSP
SLEEP
PS
BASIC
OPERATION
3 2
VIDEO
TUNER
TUNED STEREO MEM
PTY RT CT
EON
1A -AAM11440kkHz
1
Rotate INPUT to select TUNER as the input
source.
INPUT
4
Press PRESET/TUNING l / h once to begin
automatic tuning.
Press h to tune into a higher frequency, or press l
to tune into a lower frequency.
l PRESET/TUNING h
LEVEL
2
Press FM/AM to select the reception band.
“FM” or “AM” appears in the front panel display.
R/VCR2
FM/AM
FM
or
AM
VCR-1
T CINEMA
SP
TUAL
AB
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
TUNED STEREO MEM
PTY RT CT
EON
1A -AAM11530kkHz
When tuned into a station, the TUNED indicator
lights up and the frequency of the received station is
shown in the front panel display.
English
39
00_RXV750_U_EN.book Page 40 Tuesday, February 17, 2004 10:08 AM
TUNING
■ Manual tuning
If the signal from the station you want to select is weak,
tune into it manually. Manually tuning into an FM station
will automatically switch the tuner to monaural reception
to increase the signal quality.
1
Select TUNER and the reception band
following steps 1 and 2 as described in
“Automatic tuning”.
2
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator disappears from
the front panel display.
Presetting stations
■ Automatically presetting FM stations
You can use the automatic preset tuning feature to store
FM stations. This function enables this unit to
automatically tune into FM stations with strong signals,
and to store up to 40 (8 stations in 5 groups, A1 through
E8) of those stations in order. You can then recall any
preset station easily by selecting the preset station number.
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
EDIT
A/B/C/D/E
l PRESET/TUNING h
NEXT
LEVEL
PROGRAM
TUNING MODE
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
AUTO
STRAIGHT
SPEAKERS
A
B
TONE CONTROL
INPUT MODE
PURE DIRECT
MULTI CH
INPUT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
Disappears
AUTO/MAN'L MONO
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
(U.S.A. model)
1
1
3
2
Press FM/AM to select the FM band.
PRESET/TUNING
FM/AM
FM
EDIT
R/VCR2
VCR-1
T CINEMA
SP
TUAL
AB
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
TUNED STEREO MEM
PTY RT CT
EON
1A -AAM11440kkHz
2
Press TUNING MODE (AUTO/MAN’L MONO)
so that the AUTO indicator lights up in the
front panel display.
TUNING MODE
3
Press PRESET/TUNING l / h to tune into
the desired station manually.
Hold down the button to
l PRESET/TUNING h
continue searching.
LEVEL
AUTO
Lights up
AUTO/MAN'L MONO
If a colon (:) appears in the front panel display, tuning
is not possible. Press PRESET/TUNING (EDIT) to
turn the colon (:) off.
PRESET/TUNING
EDIT
R/VCR2
VCR-1
T CINEMA
SP
TUAL
AB
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
TUNED STEREO MEM
PTY RT CT
EON
1A -AAM11440kkHz
40
00_RXV750_U_EN.book Page 41 Tuesday, February 17, 2004 10:08 AM
TUNING
■ Manually presetting stations
3
Press and hold MEMORY (MAN’L/AUTO FM)
for more than 3 seconds.
The preset number, the MEMORY and AUTO
indicators flash. After about 5 seconds, automatic
presetting starts from the frequency currently
displayed and proceeds toward the higher
frequencies.
You can also store up to 40 stations (8 stations in 5 groups,
A1 through E8) manually.
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
l PRESET/TUNING h
A/B/C/D/E
NEXT
EDIT
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
MEMORY
SILENT CINEMA
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
MAN'L/AUTO FM
(U.S.A. model)
3
t
96
24
q EX
q PL
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q PL
q PL x
PCM
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
EON
1A 1:FM187.5kMHz
dB
ft
mS
dB
2,5
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
4
96/24
L C R
1
LFE SL SB SR
96
24
q EX
q PL
q PL
q PL x
PCM
Notes
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• If the number of the received stations does not reach 40 (E8),
automatic preset tuning has automatically stopped after
searching all stations.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune into it manually,
and store it by following the procedure in “Manually presetting
stations”.
t
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
1A 1:AM18630kkHz
dB
ft
mS
dB
96/24
L C R
LFE SL SB SR
When tuned into a station, the front panel display
shows the frequency of the station received.
2
Press MEMORY (MAN’L/AUTO FM).
The MEMORY indicator flashes for about 5 seconds.
BASIC
OPERATION
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
Tune into a station.
See page 39 for tuning instructions.
MEMORY
MEMORY
MAN'L/AUTO FM
Flashes
Automatic preset tuning options
You can select the preset number from which this unit will
store FM stations and/or begin tuning toward lower
frequencies.
After pressing MEMORY in step 3:
1 Press A/B/C/D/E, then PRESET/TUNING l / h to
select the preset number under which the first station
will be stored. Automatic preset tuning will stop when
stations have all been stored up to E8.
2 Press PRESET/TUNING (EDIT) to turn off the colon
(:) and then press PRESET/TUNING l to begin
tuning toward the lower frequencies.
Press A/B/C/D/E repeatedly to select a preset
station group (A to E) while the MEMORY
indicator is flashing.
The group letter appears. Check that the colon (:)
appears in the front panel display.
A/B/C/D/E
NEXT
t
96
24
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q EX
q PL
q PL
q PL x
PCM
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
1C 1:AM18630kkHz
dB
ft
mS
dB
96/24
L C R
LFE SL SB SR
Preset group
English
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the preset stations may be cleared. If
so, store the stations again by using the presetting
station methods.
3
41
00_RXV750_U_EN.book Page 42 Tuesday, February 17, 2004 10:08 AM
TUNING
4
Press PRESET/TUNING l / h to select a
preset station number (1 through 8) while the
MEMORY indicator is flashing.
Press h to select a higher preset station number.
Press l to select a lower preset station number.
Selecting preset stations
You can tune any desired station simply by selecting the
preset station number under which it was stored.
l PRESET/TUNING h
VOLUME
LEVEL
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
A/B/C/D/E
l PRESET/TUNING h
NEXT
LEVEL
EDIT
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
STRAIGHT
SPEAKERS
A
B
TONE CONTROL
INPUT MODE
PURE DIRECT
MULTI CH
INPUT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
t
96
24
q EX
q PL
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q PL
q PL x
PCM
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
VIDEO
L
AUDIO
R
OPTICAL
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
(U.S.A. model)
dB
1C 3:AM18630kkHz
ft
mS
dB
96/24
L C R
1 2
LFE SL SB SR
Preset number
MODE
PTY SEEK
START
SET MENU
LEVEL
TITLE
MUTE
MENU
TV VOL
TV INPUT
CH
5
Press MEMORY (MAN’L/AUTO FM) on the
front panel while the MEMORY indicator is
flashing.
The station band and
MEMORY
frequency appear in the front
panel display with the preset
group and number you have
selected.
MAN'L/AUTO FM
t
96
24
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q EX
q PL
q PL
q PL x
PCM
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
1C 3:AM18630kkHz
96/24
ON SCREEN
STRAIGHT
DISPLAY
1
2
EFFECT
When performing this operation with the remote
control, first press TUNER to set the remote to
tuner mode.
1
dB
ft
mS
dB
PRESET
TEST
TV VOL
PHONO
EON
CH
TV MUTE
SELECT
PRESET
RETURN
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
A/B/C/D/E
L C R
LFE SL SB SR
Press A/B/C/D/E to select the preset station
group.
The preset group letter appears in the front panel
display and changes each time you press the button.
A/B/C/D/E
SET MENU
Shows the displayed station has been stored as C3.
or
MENU
NEXT
6
Front panel
Repeat steps 1 to 5 to store other stations.
Notes
• Any stored station data existing under a preset number is
cleared when you store a new station under that preset number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
A/B/C/D/E
2
Remote control
Press PRESET/TUNING l / h (PRESET j / i
on the remote control) to select a preset
station number (1 through 8).
The preset group and number appear on the front
panel display along with the station band, frequency
and the TUNED indicator lights up.
+
TV VOL
l PRESET/TUNING h
or
CH
CH
TV MUTE
SELECT
–
+
LEVEL
PRESET
PRESET
Front panel
TV VOL
–
Remote control
DVR/VCR2
VCR-1
SILENT CINEMA
SP
VIRTUAL
AB
x
42
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
TUNED STEREO MEMORY M
PTY RT CT
EON
1E 1:FM187.5kMHz
ft
mS
dB
9
00_RXV750_U_EN.book Page 43 Tuesday, February 17, 2004 10:08 AM
TUNING
Exchanging preset stations
4
You can exchange the assignment of two preset stations
with each other. The example below describes the
procedure for exchanging preset station “E1” with “A5”.
Press PRESET/TUNING (EDIT) again.
The stations stored at the two preset assignments are
exchanged.
PRESET/TUNING
EDIT
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
A/B/C/D/E
l PRESET/TUNING h
NEXT
EDIT
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
DVR/VCR2
STRAIGHT
SPEAKERS
A
B
TONE CONTROL
INPUT MODE
VCR-1
SILENT CINEMA
SP
VIRTUAL
AB
INPUT
PHONES
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
x
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
VIDEO
L
AUDIO
R
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
TUNED STEREO MEMORY M
PTY RT CT
EON
1E EDIT18E1-A5Hz
ft
mS
dB
9
OPTICAL
(U.S.A. model)
2,4
1,3 1,3
Select preset station “E1” using A/B/C/D/E
and PRESET/TUNING l / h.
See “Selecting preset stations”.
2
Press and hold PRESET/TUNING (EDIT) for
more than 3 seconds.
“E1” and the MEMORY indicator flash in the front
panel display.
BASIC
OPERATION
1
PRESET/TUNING
EDIT
DVR/VCR2
VCR-1
SILENT CINEMA
SP
VIRTUAL
x
3
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
AB
SLEEP
MD/CD-R
TUNER
PTY HOLD AUTO
HiFi DSP
PS
CD
TUNED STEREO MEMORY M
PTY RT CT
EON
1E 1:FM187.5kMHz
ft
mS
dB
9
Select preset station “A5” using A/B/C/D/E
and PRESET/TUNING l / h.
“A5” and the MEMORY indicator flash in the front
panel display.
A/B/C/D/E
l PRESET/TUNING h
NEXT
LEVEL
DVR/VCR2
VCR-1
SILENT CINEMA
SP
VIRTUAL
AB
x
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
TUNED STEREO MEMORY M
PTY RT CT
EON
1A 5:FM190.6kMHz
ft
mS
dB
9
English
43
00_RXV750_U_EN.book Page 44 Tuesday, February 17, 2004 10:08 AM
RECORDING
RECORDING
Recording adjustments and other operations are
performed from the recording components. Refer to the
operating instructions for those components.
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
l PRESET/TUNING h
A/B/C/D/E
NEXT
EDIT
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
(U.S.A. model)
1
2
TRANSMIT
RE-NAME
CLEAR
LEARN
SYSTEM
1
POWER
STANDBY
SLEEP
INPUT MODE
MULTI CH IN
A
B
PHONO
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
2
SELECT
1
Turn on the power of this unit and all
connected components.
2
Select the source component you want to
record from.
INPUT
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
or
Front panel
Remote control
3
Start playback (or select a broadcast station)
on the source component.
4
Start recording on the recording component.
y
Do a test recording before you start an actual recording.
44
Notes
• When this unit is set in the standby mode, you cannot record
between other components connected to this unit.
• The setting of TONE CONTROL, VOLUME, “SPEAKER
LEVEL” (page 56) and programs does not affect recorded
material.
• A source connected to the MULTI CH INPUT jacks of this unit
cannot be recorded.
• S-Video and composite video signals pass independently
through this unit’s video circuits. Therefore, when recording or
dubbing video signals, if your video source component is
connected to provide only an S-Video (or only a composite
video) signal, you can record only an S-Video (or only a
composite video) signal to your VCR.
• Digital signals input to the DIGITAL INPUT jacks are not
output to the analog AUDIO OUT (L/R) jacks for recording.
Likewise, analog signals input to the AUDIO IN (L/R) jacks are
not output to the DIGITAL OUTPUT jack. Therefore, if your
source component is connected to provide only digital (or
analog) signals, you can only record digital (or analog) signals.
• A given input source is not output on the same REC OUT
channel. (For example, the signal input from VCR 1 IN is not
output on VCR 1 OUT.)
• Check the copyright laws in your country to record from
records, CDs, radio, etc. Recording of copyrighted material may
infringe copyright laws.
If you playback a video source that uses scrambled or
encoded signals to prevent it from being dubbed, the
picture itself may be disturbed due to those signals.
■ Special considerations when recording
DTS software
The DTS signal is a digital bitstream. Attempting to
digitally record the DTS bitstream will result in noise
being recorded. Therefore, if you want to use this unit to
record sources that have DTS signals recorded on them,
the following considerations and adjustments need to be
made.
For DVDs and CDs encoded with DTS, when your player
is compatible with the DTS format, follow its operating
instructions to make a setting so that the analog signal will
be output from the player.
00_RXV750_U_EN.book Page 45 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PROGRAM DESCRIPTIONS
SOUND FIELD PROGRAM DESCRIPTIONS
This unit is equipped with a variety of precise digital decoders that allow you to enjoy multichannel playback from
almost any sound source (stereo or multichannel). This unit is also equipped with a YAMAHA digital sound field
processing (DSP) chip containing several sound field programs which you can use to enhance your playback experience.
Most of these sound field programs are precise digital recreations of actual acoustic environments found in famous
concert halls, music venues, and movie theaters.
y
The YAMAHA CINEMA DSP modes are compatible with all Dolby Digital, DTS, and Dolby Surround sources. Set the input mode to
AUTO (see page 37) to enable this unit to automatically switch to the appropriate digital decoder according to the input signal.
Notes
• This unit’s DSP sound field programs are recreations of real-world acoustic environments made from precise measurements taken in
the actual hall, etc. Thus you may notice variations in the strength of the reflections coming from the front, back, left and right.
• Feel free to choose a sound field program based on your listening preference, and not purely on the name of the program itself.
For movie/video sources
You can select from the following sound fields when playing movie or video sources. The sound fields marked “MULTI”
can be used with multi-channel sources, like DVD, digital TV, etc. Those marked “2-CH” can be used with 2-channel
(stereo) sources like TV programs, video tapes, etc.
Program
Features
Downmixes multi-channel sources to 2 channel (left and right) or plays back 2-channel sources
as is.
MUSIC VIDEO
This program lends an enthusiastic atmosphere to the sound, giving you the feeling you are at
an actual jazz or rock concert.
ENTERTAINMENT:
Game
This program adds a deep and spatial feeling to video game sounds.
TV THEATER:
Mono Movie
This program is provided for reproducing monaural video sources (such as old movies). The
program produces the optimum reverberation to create sound depth using only the presernce
sound field.
TV THEATER:
Variety/Sports
Though the presence sound field is relatively narrow, the surround sound field employs the
sound environment of a large concert hall. This effect enhances the experience of watching
various TV programs such as news, variety shows, music programs or sports programs.
MOVIE THEATER:
Spectacle
CINEMA DSP processing. This program creates the extremely wide sound field of a 70-mm
movie theater. It precisely reproduces the source sound in detail, making both the video and the
sound field incredibly real. This is ideal for any kind of video source encoded with Dolby
Surround, Dolby Digital or DTS (especially large-scale movie productions).
MOVIE THEATER:
Sci-Fi
CINEMA DSP processing. This program clearly reproduces dialog and sound effects in the
latest sound form for science fiction films, thus creating a broad and expansive cinematic space
amid silence. You can enjoy science fiction films in a virtual-space sound field that includes
Dolby Surround, Dolby Digital and DTS-encoded software employing the most advanced
techniques.
MOVIE THEATER:
Adventure
CINEMA DSP processing. This program is ideal for precisely reproducing the sound design of
the newest 70-mm and multichannel soundtrack films. The sound field is made to be similar to
that of the newest movie theaters, so the reverberations of the sound field itself are restrained
as much as possible.
MOVIE THEATER:
General
CINEMA DSP processing. This program is for reproducing sounds from 70-mm and
multichannel soundtrack films, and is characterized by soft and extensive sound field.
SOUND FIELD
PROGRAMS
STEREO:
2ch Stereo
Sources
MULTI
2-CH
English
45
00_RXV750_U_EN.book Page 46 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PROGRAM DESCRIPTIONS
Program
Features
DOLBY DIGITAL:
SUR. STANDARD
Standard 5.1-channel processing for Dolby Digital sources.
DOLBY DIGITAL:
SUR. ENHANCED
CINEMA DSP enhanced processing for Dolby Digital sources.
q D+PLIIx Movie:
SUR. STANDARD
Standard 6.1/7.1-channel processing (Dolby Pro Logic IIx Movie) for Dolby Digital sources.
q D+PLIIx Movie:
SUR. ENHANCED
CINEMA DSP enhanced 6.1/7.1-channel processing (Dolby Pro Logic IIx Movie) for Dolby
Digital sources.
DOLBY D EX:
SUR. STANDARD
Standard 6.1-channel processing for Dolby Digital sources.
DOLBY D EX:
SUR. ENHANCED
CINEMA DSP enhanced 6.1-channel processing (Dolby Digital EX) for Dolby Digital
sources.
DTS:
SUR. STANDARD
Standard 5.1-channel processing for DTS sources.
DTS 96/24:
SUR. STANDARD
Standard 5.1-channel processing for 96-kHz/24-bit DTS sources.
DTS:
SUR. ENHANCED
CINEMA DSP enhanced processing for DTS and 96-kHz/24-bit DTS sources.
DTS+PLIIx Movie:
SUR. STANDARD
Standard 6.1/7.1-channel processing (Dolby Pro Logic IIx Movie) for DTS sources.
DTS+PLIIx Movie:
SUR. ENHANCED
CINEMA DSP enhanced 6.1/7.1-channel processing (Dolby Pro Logic IIx Movie) for DTS
sources.
DTS+DOLBY EX:
SUR. STANDARD
Standard 6.1-channel processing (Dolby Digital EX) for DTS sources.
DTS+DOLBY EX:
SUR. ENHANCED
CINEMA DSP enhanced 6.1-channel processing (Dolby Digital EX) for DTS sources.
DTS ES Mtrx6.1:
SUR. STANDARD
Standard 6.1-channel processing (DTS-ES Matrix) for DTS sources.
DTS ES Mtrx6.1:
SUR. ENHANCED
CINEMA DSP enhanced processing (DTS-ES Matrix) for DTS sources.
DTS ES Disc6.1:
SUR. STANDARD
Standard 6.1-channel processing (DTS-ES Discrete) for DTS sources.
DTS ES Disc6.1:
SUR. ENHANCED
CINEMA DSP enhanced processing (DTS-ES Discrete) for DTS sources.
46
Sources
MULTI
00_RXV750_U_EN.book Page 47 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PROGRAM DESCRIPTIONS
Program
Features
PRO LOGIC:
SUR. STANDARD
Standard processing for Dolby Surround sources.
PRO LOGIC:
SUR. ENHANCED
CINEMA DSP enhanced precessing for Dolby Surround sources.
PRO LOGIC IIx:
PLIIx Movie
Dolby Pro Logic IIx processing for movie software.
PRO LOGIC II:
PLII Movie
Dolby Pro Logic II processing for movie software.
PRO LOGIC IIx:
PLIIx Game
Dolby Pro Logic IIx processing for game software.
PRO LOGIC II:
PLII Game
Dolby Pro Logic II processing for game software.
DTS: Neo:6 Cinema
DTS processing for movie software.
* You can select either Pro Logic IIx or Pro
Sources
2-CH
Logic II processing using the PLII/PLIIx parameter on page 78.
SOUND FIELD
PROGRAMS
English
47
00_RXV750_U_EN.book Page 48 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PROGRAM DESCRIPTIONS
For music sources
You can select from the following sound fields when playing music sources, like CD, FM/AM broadcasting, tapes, etc.
Program
Features
CONCERT HALL
HiFi DSP processing. A classic shoe-box type concert hall with approximately 1700 seats.
Pillars and ornate carvings create extremely complex reflections which produce a very full,
rich sound.
JAZZ CLUB
HiFi DSP processing. This is the sound field at stage front in “The Bottom Line”, a famous
New York jazz club. The floor can seat 300 people to the left and right in a sound field offering
a real and vibrant sound.
ROCK CONCERT
HiFi DSP processing. The ideal program for lively, dynamic rock music. The data for this
program was recorded at LA’s “hottest” rock club. The listener’s virtual seat is at the center-left
of the hall.
ENTERTAINMENT:
Disco
HiFi DSP processing. This program recreates the acoustic environment of a lively disco in the
heart of a big city. The sound is dense and highly concentrated. It is also characterized by highenergy, “immediate” sound.
q D+PLIIx Music:
SUR. STANDARD
Standard Dolby Digital and Dolby Pro Logic IIx processing for music sources.
q
D+PLIIx Music:
SUR. ENHANCED
CINEMA DSP enhanced Dolby Digital and Dolby Pro Logic IIx processing for music sources.
DTS+PLIIx Music:
SUR. STANDARD
Standard DTS and Dolby Pro Logic IIx processing for music sources.
DTS+PLIIx Music:
SUR. ENHANCED
CINEMA DSP enhanced DTS and Dolby Pro Logic IIx processing for music sources.
STEREO:
2ch Stereo
2-channel (left and right) playback.
STEREO:
7ch Stereo
Use to increase the output stereo sources (in stereo) from all speakers. This provides a larger
sound field and is ideal for background music at parties, etc.
PRO LOGIC IIx:
PLIIx Music
Dolby Pro Logic IIx processing for music software.
PRO LOGIC II:
PLII Music
Dolby Pro Logic II processing for music software.
DTS: Neo:6 Music
DTS processing for music software.
MULTI
2-CH
MULTI
* You can select either Pro Logic IIx or Pro
48
Sources
Logic II processing using the PLII/PLIIx parameter on page 78.
2-CH
00_RXV750_U_EN.book Page 49 Tuesday, February 17, 2004 10:08 AM
ADVANCED OPERATIONS
ADVANCED OPERATIONS
Selecting the OSD mode
Using the sleep timer
You can display this unit’s operating information on a
video monitor. If you display the SET MENU and sound
field program parameter settings on a monitor, it is much
easier to see the available options and parameters than it is
by reading this information on the front panel display.
1
Turn on the video monitor connected to this
unit.
2
Press ON SCREEN repeatedly to change the
OSD mode.
The OSD mode changes in the
following order: full display, short
DISPLAY
display, and display off.
Use this feature to automatically set this unit in the
standby mode after a certain amount of time. The sleep
timer is useful when you are going to sleep while this unit
is playing or recording a source. The sleep timer also
automatically turns off any external components
connected to the AC OUTLET(S).
■ Setting the sleep timer
TRANSMIT
RE-NAME
CLEAR
LEARN
SYSTEM
POWER
STANDBY
SLEEP
INPUT MODE
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
2
ON SCREEN
SELECT
Full display
Always shows the sound field program parameter settings
as well as the contents of the front panel display.
POWER
POWER
TV
AV
AMP
Short display
Briefly shows the contents of the front panel display at the
bottom of the screen each time you operate this unit.
1
Select a source and start playback on the
source component.
Display off
Only operations performed using ON SCREEN are
displayed. The OSD is displayed when using SET MENU
or the test tone feature, even if the OSD mode is set to
“Display off”.
2
Press SLEEP repeatedly to set
the amount of time.
Each time you press SLEEP, the front
panel display changes as shown
below. The SLEEP indicator flashes
while switching the amount of time
for the sleep timer.
P08 MOVIE THEATER
SLEEP 120min
SLEEP OFF
SLEEP 90min
SLEEP 30min
SLEEP 60min
P08MOVIETHEATER
General
t
Full display
Short display
96
24
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q EX
q PL
q PL
q PL x
PCM
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
1E SLEEP8120minz
dB
ft
mS
dB
96/24
ADVANCED
OPERATION
.General
DSPLEVEL;;;;0dB
P.INIT.DLY;;15ms
P.ROOMSIZE;;1.0
S.INIT.DLY;;20ms
S.ROOMSIZE;;1.0
SLEEP
L C R
LFE SL SB SR
Notes
• The OSD signal is not output to the REC OUT jack, and will
not be recorded.
• You can set the OSD to turn on (gray background) or off when a
video source is not being reproduced (or the source component
is turned off) by using “DISPLAY SET” (see page 60).
The SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound
field program.
SLEEP indicator
t
96
24
q EX
q PL
DVR/VCR2
VCR-1
SILENT CINEMA
MATRIX DISCRETE VIRTUAL
SP
AB
q DIGITAL
q PL
q PL x
PCM
V-AUX
DTV/CBL
DVD
NIGHT ZONE2
SLEEP
MD/CD-R
PTY HOLD AUTO
HiFi DSP
PS
TUNER
CD
PHONO
TUNED STEREO MEMORY MUTE VOLUME
PTY RT CT
EON
1E CONCERT2HALLz
dB
ft
mS
dB
96/24
L C R
LFE SL SB SR
English
49
00_RXV750_U_EN.book Page 50 Tuesday, February 17, 2004 10:08 AM
ADVANCED OPERATIONS
■ Canceling the sleep timer
Press SLEEP repeatedly until “SLEEP OFF” appears in
the front panel display.
After a few seconds, “SLEEP OFF” disappears, and the
SLEEP indicator goes off.
SLEEP
SLEEP OFF
y
Manually adjusting speaker levels
You can adjust the output level of each speaker while
listening to a music source. This is also possible when
playing sources through the MULTI CH INPUT jacks.
Please note that this operation will override the level
adjustments made in “AUTO SETUP” (page 26),
“SPEAKER LEVEL” (page 56) and “Using the test tone”
(page 51).
The sleep timer setting can also be canceled by pressing
STANDBY on the remote control (or STANDBY/ON on the front
panel) to set this unit to the standby mode.
POWER
POWER
TV
AV
AMP
1
REC
AUDIO
DISC SKIP
VOL
FREQ/RDS
MODE
2
EON
PTY SEEK
START
SET MENU
LEVEL
TITLE
MUTE
MENU
4
TV VOL
TV INPUT
CH
A/B/C/D/E
TV MUTE
SELECT
CH
PRESET
PRESET
TEST
ON SCREEN
STRAIGHT
TV VOL
RETURN
DISPLAY
EFFECT
3
1
Press AMP.
2
Press LEVEL repeatedly to select the
speaker you want to adjust.
FRONT L
CENTER
FRONT R
SUR.R
SUR.B.R
SUR.B.L
SUR.L
SWFR
PRES
Front left speaker level
Center speaker level
Front right speaker level
Surround right speaker level
Surround back right speaker level
Surround back left speaker level
Surround left speaker level
Subwoofer level
Presence speaker level
y
Once you press LEVEL, you can also select the speaker by
pressing u / d.
3
Press j / i to adjust the speaker output level.
The control range is from +10 dB to –10 dB.
4
Press SELECT when you have completed
your adjustment.
y
This operation can also be performed using the controls on the
front panel. Press NEXT repeatedly to select the speaker you
want to adjust, then press LEVEL –/+ to adjust the output level.
50
00_RXV750_U_EN.book Page 51 Tuesday, February 17, 2004 10:08 AM
ADVANCED OPERATIONS
■ Outputting the test tone from the
PRESENCE speakers
Using the test tone
You can use the test tone feature to manually balance your
speaker levels. Please note that this operation will override
the level adjustments made in “AUTO SETUP” (page 26),
“SPEAKER LEVEL” (page 56) and “Manually adjusting
speaker levels” (page 50). Use the test tone to set speaker
levels so that the volume from each speaker is identical
when heard from your listening position.
6
Press u / d repeatedly to select the speaker
from which you want to output the test tone.
TEST
TEST
TEST
TEST
FRONT
PRESENCE
PRES L
PRES R
Front speakers
Presence speakers
Left presence speakers
Right presence speakers
Note
You cannot activate the test tone if headphones are connected to
the PHONES jack. Remove the headphones from the PHONES
jack.
POWER
POWER
TV
AV
AMP
1
REC
7
Press j / i to adjust the presence speaker
volumes.
8
Press TEST when you have completed your
adjustment.
The test tone stops.
AUDIO
DISC SKIP
VOL
FREQ/RDS
MODE
EON
START
PTY SEEK
SET MENU
LEVEL
TITLE
4,7
CH
A/B/C/D/E
CH
TV MUTE
SELECT
PRESET
PRESET
2,5,8
MUTE
MENU
TV VOL
TV INPUT
ON SCREEN
TEST
STRAIGHT
TV VOL
RETURN
DISPLAY
3,6
EFFECT
1
Press AMP.
2
Press TEST.
The unit outputs a test tone.
3
Press u / d repeatedly to select the speaker
you want to adjust.
LEFT
CENTER
RIGHT
SUR.R
SUR.B.R
SUR.B.L
SUR.L
SUBWOOFER
Front left speaker
Center speaker
Front right speaker
Right surround speaker
Right surround back speaker
Left surround back speaker
Left surround speaker
Subwoofer
4
Press j / i to adjust the speaker volumes.
5
Press TEST when you have completed your
adjustment.
The test tone stops.
ADVANCED
OPERATION
TEST
TEST
TEST
TEST
TEST
TEST
TEST
TEST
If PRESENCE SP in “SPEAKER SET” is set to YES,
you can adjust the presence speaker volumes
(proceed to step 6).
English
51
00_RXV750_U_EN.book Page 52 Tuesday, February 17, 2004 10:08 AM
SET MENU
SET MENU
You can use the following parameters in SET MENU to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ AUTO SETUP
Use to specify which speaker parameters auto setup will adjust, and to activate the auto setup procedure (see page 26).
■ MANUAL SETUP
Use to manually adjust speaker and system parameters.
1 SOUND MENU
Use to manually adjust any speaker setting, alter the quality and tone of the sound output by the system or compensate for
video signal processing delays when using LCD monitors or projectors.
y
Most of the parameters described in SOUND MENU are set automatically when you run auto setup (see page 26). You can use SOUND
MENU to make further adjustments, but we recommend running auto setup first.
Item
Features
Page
A)SPEAKER SET
Selects the size of each speaker, the speakers for low-frequency signal output, and the cross over
frequency.
54
B)SPEAKER LEVEL
Adjusts the output level of each speaker.
56
C)SP DISTANCE
Adjusts the delay time of each speaker.
56
D)CENTER GEQ
Adjusts the tonal quality of the center speaker.
57
E)LFE LEVEL
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
57
F)DYNAMIC RANGE
Adjusts the dynamic range for Dolby Digital or DTS signals.
57
G)AUDIO SET
Customizes the muting level, audio delay and height of the front and center channel sounds.
57
H)PR/SB SELECT
Selects priority to either surround back or presence speakers when both sets of speakers are
connected to this unit.
58
2 INPUT MENU
Use to reassign digital input/outputs, select the input mode or rename your inputs.
Item
Features
Page
A)I/O ASSIGNMENT Assigns jacks according to the component to be used.
58
B)INPUT MODE
Selects the initial input mode of the source.
59
C)INPUT RENAME
Changes the name of the inputs.
59
3 OPTION MENU
Use to adjust the optional system parameters.
Item
Features
Page
A)DISPLAY SET
Adjusts the brightness of the display and converts video signals.
60
B)MEMORY GUARD
Locks sound field program parameters and other SET MENU settings.
60
C)PARAM. INI
Initializes the parameters of a group of sound field programs.
61
D)ZONE SET
Specifies the location of the speakers connected to the SPEAKERS B terminals.
61
E)ZONE2 SET
Selects how the ZONE 2 speakers will be amplified.
61
52
00_RXV750_U_EN.book Page 53 Tuesday, February 17, 2004 10:08 AM
SET MENU
Using SET MENU
4
Use the remote control to access and adjust each
parameter.
Press SELECT to enter MANUAL SETUP.
1 SOUND MENU appears on the front panel display.
;MANUAL SETUP
+
TV VOL
POWER
POWER
TV
1
AMP
AV
CH
–
REC
AUDIO
TV MUTE
SELECT
+
[]/[]:Up/Down
[SELECT]:Enter
PRESET
VOL
FREQ/RDS
MODE
TV VOL
EON
PTY SEEK
TITLE
–
START
SET MENU
LEVEL
MUTE
2,8
MENU
TV VOL
TV INPUT
3-7
CH
A/B/C/D/E
TV MUTE
SELECT
CH
PRESET
PRESET
ON SCREEN
TEST
STRAIGHT
TV VOL
RETURN
p
PRESET
CH
p
DISC SKIP
.1SOUNDMENU
2INPUTMENU
3OPTIONMENU
DISPLAY
5
Press u / d to select the desired menu.
6
Press SELECT to enter the selected menu.
EFFECT
STEREO
HALL
JAZZ
ROCK
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
EX/ES
9
0
10
ENTER
CHP/INDEX
1 SOUND MENU 1/2
+
TV VOL
y
CH
–
TV MUTE
SELECT
CH
+
PRESET
p
PRESET
p
You can change SET MENU parameters while the unit is
reproducing sound.
.A)SPEAKERSET
B)SPEAKERLEVEL
C)SPDISTANCE
D)CENTERGEQ
[]/[]:Up/Down
[SELECT]:Enter
TV VOL
–
Note
You cannot change some SET MENU parameters while the unit
is in either cinema or music night listening mode.
1
7
Press AMP.
AMP
Press u / d to select the item you want to
adjust, then press j / i to change the setting
of the item.
B)SPEAKER LEVEL
2
-+
.FR
C
SL
Press SET MENU.
SET MENU
MENU
A/B/C/D/E
3
Press u / d to select MANUAL SETUP.
CH
–
TV MUTE
SELECT
SET MENU
PRESET
CH
+
;AUTOSETUP
.;MANUALSETUP
PRESET
To exit, press SET MENU when finished.
SET MENU
[]/[]:Up/Down
[SELECT]:Enter
p
–
p
TV VOL
8
MENU
ADVANCED
OPERATION
+
TV VOL
Repeat this operation to select and adjust each setting.
To return to the previous menu level, press RETURN.
A/B/C/D/E
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, if the power cord is disconnected from the
AC outlet, or the power supply is cut for more than one
week, the stored data will be lost. If so, adjust the
items again.
English
53
00_RXV750_U_EN.book Page 54 Tuesday, February 17, 2004 10:08 AM
SET MENU
1 SOUND MENU
Use to manually adjust any speaker setting or compensate
for video signal processing delays when using LCD
monitors or projectors. Most of the SOUND MENU
parameters are set automatically when you run auto setup
(see page 26).
Front speakers FRONT SP
Choices: SMALL, LARGE
FRONT SP
SMALL)LARGE
1 SOUND MENU 1/2
p
p
.A)SPEAKERSET
B)SPEAKERLEVEL
C)SPDISTANCE
D)CENTERGEQ
[]/[]:Up/Down
[SELECT]:Enter
■ Speaker set A)SPEAKER SET
Use to manually adjust any speaker setting.
y
If you are not satisfied with the bass sounds from your speakers,
you can change these settings according to your preference.
Center speaker CENTER SP
Choices: NONE, SML, LRG
CENTER SP
NONE)SMLLRG
• Select NONE if you do not have a center speaker. The
unit directs all of the center channel signal to the front
left and right speakers.
• Select SML if you have a small center speaker. The
unit directs the low-frequency signals of the center
channel to the speakers selected with “LFE/BASS
OUT”.
• Select LRG if you have a large center speaker. The unit
directs the entire range of the center channel signal to
the center speaker.
54
• Select SMALL if you have small front speakers. The
unit directs the low-frequency signals of the front
channel to the speakers selected with “LFE/BASS
OUT”.
• Select LARGE if you have large front speakers. The
unit directs the entire range of the front left and right
channel signals to the front left and right speakers.
Surround left/right speakers SURR L/R SP
Choices: NONE, SML, LRG
SURR L/R SP
NONE)SMLLRG
• Select NONE if you do not have surround speakers.
This will set the unit to the Virtual CINEMA DSP
mode (see page 37) and automatically set the surround
back speaker setting (SURR B L/R SP) to NONE.
• Select SML if you have small surround left and right
speakers. The low-frequency signals of the surround
channel are directed to the speakers selected with
“LFE/BASS OUT”.
• Select LRG if you have large surround left and right
speakers. The entire range of the surround channel
signal is directed to the surround left and right
speakers.
00_RXV750_U_EN.book Page 55 Tuesday, February 17, 2004 10:08 AM
SET MENU
Surround back speakers SURR B L/R SP
Choices: NONE, SMLx1, SMLx2, LRGx1, LRGx2
SURR B L/R SP
Bass out LFE/BASS OUT
Low-frequency (bass) signals can be directed to the
subwoofer and/or the front left and right speakers
according to the characteristics of your system. This
setting also determines the routing of the LFE (lowfrequency effect) signals found in Dolby Digital or DTS
sources.
Choices: SWFR, FRNT, BOTH
SMLx1)SMLx2
• Select NONE if you do not have a surround back
speaker. The unit directs all of the surround back
channel signal to the surround left and right speakers.
• Select SMLx1 if you have a small surround back
speaker. The low-frequency signals of the surround
back channel are directed to the speakers selected with
“LFE/BASS OUT”, and the rest of the frequency
signals are directed to the left surround back speaker.
• Select SMLx2 if you have 2 small surround back
speakers. The low-frequency signals of the surround
back channels are directed to the speakers selected with
“LFE/BASS OUT”.
• Select LRGx1 if you have a large surround back
speaker. The unit directs the entire range of the
surround back channel signal to the left surround back
speaker.
• Select LRGx2 if you have 2 large surround back
speakers. The unit directs the entire range of the
surround back channel signal to the surround back
speakers.
Note
If you select SMLx1 or LRGx1, connect the speaker to the left
SURROUND BACK speaker terminals.
Presence speakers
Choices: NONE, YES
PRESENCE SP
LFE/BASS OUT
SWFRFRNT)BOTH
• Select SWFR if you connect a subwoofer. LFE and
low-frequency signals from other channels are directed
to the subwoofer according to the speaker settings.
• Select FRNT if you do not use a subwoofer. LFE and
low frequency signals from other channels are directed
to the front speakers according to the speaker settings
(even if you have previously set front speakers to
SML).
• Select BOTH if you connect a subwoofer and you want
to output low-frequency signals from front channels to
both the front speakers and subwoofer. LFE and lowfrequency signals from other channels are also directed
to the subwoofer according to the speaker settings. Use
this function to reinforce low-frequency signals using
the subwoofer when playing back sources such as CDs.
PRESENCE SP
CROSS OVER
ADVANCED
OPERATION
Cross over CROSS OVER
Use this feature to select a cross-over (cut-off) frequency
for all low-frequency signals. All frequencies below the
selected frequency will be sent to the subwoofer.
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
)NONEYES
FREQ;;;80Hz
• Select NONE if you do not have presence speakers.
• Select YES if you have presence speakers.
English
55
00_RXV750_U_EN.book Page 56 Tuesday, February 17, 2004 10:08 AM
SET MENU
Subwoofer phase SUBWOOFER PHASE
If bass sounds are lacking or unclear, use this feature to
switch the phase of your subwoofer.
Choices: NORMAL, REVERSE
02ASUBWOOFER PHASE
■ Speaker distance C)SP DISTANCE
Use this feature to manually input the distance of each
speaker and adjust the delay applied to respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sound will arrive at the listening position at the same time.
C)SP DISTANCE
)NORMALREVERSE
■ Speaker level B)SPEAKER LEVEL
Use these settings to manually balance the speaker levels
between the front left or surround left speakers and each
speaker selected in SPEAKER SET (page 54).
Choices: –10.0 dB to +10.0 dB
B)SPEAKER LEVEL
-+
.FR
C
SL
• FR adjusts the balance of the front left and front right
speakers.
• C adjusts the balance of the front left and center
speakers.
• SL adjusts the balance of the front left and surround
left speakers.
• SBL* adjusts the balance of the surround left and
surround back left speakers.
• SBR* adjusts the balance of the surround left and
surround back right speakers.
• SR adjusts the balance of the surround left and
surround right speakers.
• SWFR adjusts the balance of the front left speaker and
subwoofer.
• PRES adjusts the balance of the front and presence
speakers.
*
SB will be displayed if you selected only one surround back
speaker in SURR B L/R SP (page 55).
y
To calibrate, use the test tone feature (see page 51).
56
p
• Select NORMAL if you do not want to reverse the
phase of your subwoofer.
• Select REVERSE to reverse the phase of your
subwoofer.
p
. UNIT;;;;;;meters
FRONTL;;;;3.00m
FRONTR;;;;3.00m
CENTER;;;;;3.00m
[]/[]:Up/Down
[<]/[>]:Adjust
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
U.S.A. and Canada models: feet (ft)
Other models: meters (m)
• Select meters to input speaker distances in meters.
• Select feet to input speaker distances in feet.
Speaker distances
Choices: 0.3 to 24.00 m (1 to 80 ft)
• FRONT L adjusts the distance of the front left speaker.
Initial setting: 3.0 m (10.0 ft)
• FRONT R adjusts the distance of the front right
speaker. Initial setting: 3.0 m (10.0 ft)
• CENTER adjusts the distance of the center speaker.
Initial setting: 3.0 m (10.0 ft)
• SURR L adjusts the distance of the surround left
speaker. Initial setting: 3.0 m (10.0 ft)
• SURR R adjusts the distance of the surround right
speaker. Initial setting: 3.0 m (10.0 ft)
• SB L* adjusts the distance of the surround back left
speaker. Initial setting: 2.10 m (7.0 ft)
• SB R* adjusts the distance of the surround back right
speaker. Initial setting: 2.10 m (7.0 ft)
• SWFR adjusts the distance of the subwoofer. Initial
setting: 3.0 m (10.0 ft)
• PRES L adjusts the distance of the presence left
speaker. Initial setting: 3.0 m (10.0 ft)
• PRES R adjusts the distance of the presence right
speaker. Initial setting: 3.0 m (10.0 ft)
*
SURR B will be displayed if you selected only one surround
back speaker in SURR B L/R SP (page 55).
00_RXV750_U_EN.book Page 57 Tuesday, February 17, 2004 10:08 AM
SET MENU
■ Center graphic equalizer D)CENTER GEQ
Use this feature to adjust the built-in 5-band graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers.
You can make adjustments listening to the currently
selected source component or a test tone.
You can adjust 5 frequency bands: 100Hz, 300Hz, 1kHz,
3kHz, 10kHz
Choices: –6 to +6 dB
D)CENTER GEQ
F)DYNAMIC RANGE
.SP:MINSTD)MAX
HP:MINSTD)MAX
p
p
[]/[]:Up/Down
[<]/[>]:Select
p
p
.TEST)OFFON
-+
100Hz0dB
300Hz0dB
1kHz0dB
3kHz0dB
10kHz0dB
[]/[]:Up/Down
[<]/[>]:Adjust
■ Dynamic range F)DYNAMIC RANGE
Use to select the amount of dynamic range compression to
be applied to your speakers or headphones. This setting is
effective only when the unit is decoding Dolby Digital and
DTS signals.
Choices: MIN (minimum), STD (standard), MAX
(maximum)
• Select ON to output test tones from the front left and
center speakers, and adjust the tonal quality of the
center speaker.
• Select OFF to stop the test tone and output the
currently selected source component.
• Press u / d to select a frequency band.
• Press j / i to adjust the selected frequency band.
Speaker SP
Select to adjust the speaker compression.
Headphone HP
Select to adjust the headphone compression.
• Select MIN if you regularly listen at low volume levels.
• Select STD for general use.
• Select MAX to preserve the greatest amount of
dynamic range.
■ Low-frequency effect level E)LFE LEVEL
■ Audio set G)AUDIO SET
Use to adjust the output level of the LFE (low-frequency
effect) channel according to the capacity of your
subwoofer or headphones. The LFE channel carries lowfrequency special effects which are only added to certain
scenes. This setting is effective only when this unit
decodes Dolby Digital or DTS signals.
Choices: –20 to 0 dB
Use to customize this units overall audio settings.
G)AUDIO SET
.AUDIOMUTE;;MUTE
AUDIODELAY;;0ms
DIALG.LIFT;;;OFF
p
p
[]/[]:Up/Down
[<]/[>]:Selet
E)LFE LEVEL
.SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
Speaker SPEAKER
Select to adjust the speaker LFE level.
Headphone HEADPHONE
Select to adjust the headphone LFE level.
Note
ADVANCED
OPERATION
p
p
[]/[]:Up/Down
[<]/[>]:Adjust
Audio mute AUDIO MUTE
Use to adjust how much the mute function reduces the
output volume.
Choices: MUTE, –20 dB
• Select MUTE to completely halt all output of sound.
• Select –20 dB to reduce the current volume by 20 dB.
Audio delay AUDIO DELAY
Use to delay the sound output and synchronize it with the
video image. This may be necessary when using certain
LCD monitors or projectors.
Choices: 0 to 160 mS
Depending on the settings of “LFE LEVEL”, some signals may
not be output from the SUB WOOFER OUTPUT jack.
English
57
00_RXV750_U_EN.book Page 58 Tuesday, February 17, 2004 10:08 AM
SET MENU
Dialog lift DIALG.LIFT
Use to turn on and off the DIALG.LIFT parameter (see
page 78). This parameter adjusts the height of the front
and center channel sounds (dialog, vocals, etc.) by
assigning some of the front and center channel elements to
the presence speakers.
Choices: OFF, ON
• Select OFF to turn off DIALG.LIFT effect.
• Select ON to turn on DIALG.LIFT effect.
2 INPUT MENU
Use to reassign digital input/outputs, select the input mode
or rename your inputs.
2 INPUTMENU
.A)I/OASSIGNMENT
B)INPUTMODE
C)INPUTRENAME
p
p
[]/[]:Up/Down
[SELECT]:Enter
Note
“DIALG.LIFT” appears only when “PRESENCE SP” is set
to YES (see page 55).
■ Presence/surround back channel select
H)PR/SB SELECT
You can select to prioritize either the surround back or
presence speakers when playing sources that contain
surround back channel signals using CINEMA DSP sound
field programs.
Choices: PRch, SBch
H)PR/SBSELECT
PRch)SBch
ASSIGNMENT
You can assign jacks according to the component to be
used if this unit’s initial settings do not correspond to your
needs. Change the following parameters to reassign the
respective jacks and effectively connect more components.
Once the inputs have been reassigned, you can select the
corresponding component by using INPUT on the front
panel or the input selector buttons on the remote control.
For COMPONENT VIDEO jacks A and B
Choices: DVD, V-AUX, DTV/CBL, VCR 1, DVR/VCR2
p
p
[]/[]:Select
[SELECT]:Return
■ Input/output assignment A)I/O
CMPNT-VINPUT
• Select PRch to use presence speakers even when
surround back channel signals are input. The signals
for the surround back channel will be output from
surround speakers.
• Select SBch to use surround back speakers when a
surround back channel signal is detected in a CINEMA
DSP program. Presence channel signals will be output
from front speakers.
.[A];;;;;DVD
(DVD)
[B];;;;;DTV/CBL
(DTV/CBL)
For OPTICAL OUTPUT jack 1
Choices: MD/CD-R, CD, V-AUX, DTV/CBL, VCR 1,
DVD, PHONO, DVR/VCR2
OPTICALOUT
.(1);;;;;MD/CD-R
(MD/CD-R )
For OPTICAL INPUT jacks 2, 3 and 4
Choices: CD, DTV/CBL, VCR 1, DVD, PHONO, DVR/
VCR2, MD/CD-R
OPTICALIN
.(2);;;;;MD/CD-R
(MD/CD-R)
(3);;;;; DVD
(DVD )
(4);;;;;DTV/CBL
(DTV/CBL )
58
00_RXV750_U_EN.book Page 59 Tuesday, February 17, 2004 10:08 AM
SET MENU
For COAXIAL INPUT jacks 5 and 6
Choices: CD, V-AUX, DTV/CBL, VCR 1, MD/CD-R,
DVD, PHONO, DVR/VCR2
■ Input rename C)INPUT RENAME
Use this feature to change the name of the inputs on the
OSD and front panel display.
C)INPUTRENAME
COAXIALIN
.(5);;;;;
CD
(
CD
)
(6);;;;; DVD
(DVD )
DVD->DVD
p
p
[<]/[>]:Position
[]/[]:Chara.
Notes
1
• You cannot select a specific item more than once for the same
type of jack.
• When you connect a component to both the COAXIAL and
OPTICAL jacks, priority is given to the input signals from the
COAXIAL jack.
Press an input selector button to select the
input you want to change the name of.
2
Press AMP.
3
Press j / i to place the _ (under-bar) under
the space or the character you want to edit.
4
Press u / d to select the character you want,
then use j / i to move to the next space.
• You can use up to 8 characters for each input.
• Press d to change the character in the following
order, or press u to go in the reverse order:
A to Z, a space, 0 to 9, a space, a to z, a space, #, *,
+, etc.
5
Repeat steps 1 through 4 to rename each
input.
6
To exit, press SET MENU when finished.
■ Input mode B)INPUT MODE
Use this feature to designate the input mode for sources
connected to the DIGITAL INPUT jacks when you turn on
this unit (see page 37 for details about the input mode).
Choices: AUTO, LAST
B)INPUTMODE
)AUTOLAST
[<]/[>]:Select
[SELECT]:Return
• Select AUTO to allow this unit to automatically detect
the type of input signal and select the appropriate input
mode.
• Select LAST to set this unit to automatically select the
last input mode used for that source.
ADVANCED
OPERATION
Note
Even if LAST is selected, the last setting for the EX/ES button
will not be recalled.
English
59
00_RXV750_U_EN.book Page 60 Tuesday, February 17, 2004 10:08 AM
SET MENU
3 OPTION MENU
Use to adjust the optional system parameters.
3 OPTIONMENU1/2
p
p
.A)DISPLAYSET
B)MEMORYGUARD
C)PARAM.INI
D)ZONESET
[]/[]:Up/Down
[SELECT]:Enter
OSD shift OSD SHIFT
Use to adjust the vertical position of the OSD.
Choices: +5 (downward) to –5 (upward)
• Press + to lower the position of the OSD.
• Press – to raise the position of the OSD.
Gray back GRAY BACK
Selecting AUTO for the on-screen display setting displays
a gray background when there’s no video signal input.
Nothing is displayed if OFF is selected.
Choices: AUTO, OFF
Note
■ Display set A)DISPLAY SET
A)DISPLAYSET
p
p
.DIMMER;;;;;;;;;0
VCONV;;;;;;;;ON
OSDSHIFT;;;;;;0
GRAYBACK;;;AUTO
CMPNTOSD;;;;;ON
[]/[]:Up/Down
[<]/[>]:sELECT
Dimmer DIMMER
Use to adjust the brightness of the front panel display.
Choices: –4 to 0
Video conversion V CONV.
Use this feature to turn on/off conversion of composite
(VIDEO) signals to both S-Video and component signals.
This allows you to output converted video signals from the
S VIDEO or COMPONENT VIDEO jacks when no
S-Video or component signals are input. This feature also
converts S-Video signals to component signals when no
component signals are input.
Choices: ON, OFF
• Select OFF not to convert any signals.
• Select ON to convert composite signals to S-Video and
component signals, and to convert S-Video signals to
component signals.
If “GRAY BACK” is set to OFF, no information will be displayed
on the screen when video signals are not being input.
Component OSD CMPNT OSD
Use this feature to turn on/off OSD output to the
COMPONENT VIDEO MONITOR OUT jacks when
using the SET MENU, test tone or parameter functions.
Choices: ON, OFF
• Select ON to output the OSD signals from
COMPONENT VIDEO MONITOR OUT jacks.
• Select OFF if you do not want to output the OSD
signals from COMPONENT VIDEO MONITOR OUT
jacks.
Note
Set menu functions even when OFF is selected.
■ Memory guard B)MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: OFF, ON
B)MEMORYGUARD
)OFFON
[<]/[>]:Select
[SELECT]:Return
Notes
• Converted video signals are only output to the MONITOR OUT
jacks. When recording you must make the same type of video
connections (i.e., S-Video) between each component.
• When converting composite video or S-Video signals from a
VCR to component video signals, the picture quality may suffer
depending on your VCR.
Select ON to protect:
• DSP program parameters
• All SET MENU items
• All speaker levels
• The on-screen display (OSD) mode
Note
When “MEMORY GUARD” is set to ON, you cannot use the test
tone or select any other SET MENU items.
60
00_RXV750_U_EN.book Page 61 Tuesday, February 17, 2004 10:08 AM
SET MENU
■ Parameter initialization C)PARAM. INI
■ Zone set D)ZONE SET
Use this feature to initialize the parameters for each sound
field program within a sound field program group. When
you initialize a sound field program group, all of the
parameter values within that group revert to their initial
settings.
Press the corresponding numeric button for the sound field
program that you want to initialize.
An asterisk (*) next to a program number means that the
parameter values have been changed from their initial
settings.
Use to specify the location of speakers connected to the
SPEAKERS B terminals.
C)PARAM.INI
1234
567*8
9
Notes
• You cannot automatically revert to the previous parameter
settings once you initialize a sound field program group.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any program groups when “MEMORY
GUARD” is set to ON.
D)ZONESET
SPB;;;;;;FRONT
[<]/[>]:Select
[SELECT]:Return
Speaker B set SP B
Use this feature to select the location of the front speakers
connected to the SPEAKERS B terminals.
Choices: FRONT, ZONE B
• Select FRONT to turn on/off SPEAKERS A and B
when the speakers connected to the SPEAKERS B
terminals are set in the main room.
• Select ZONE B if the speakers connected to the
SPEAKERS B terminals are set in another room. If
SPEAKERS A is turned OFF and SPEAKERS B is
turned ON, all the speakers including the subwoofer in
the main room are muted and the unit outputs sound
from SPEAKERS B only.
Notes
• If you connect headphones to the PHONES jack on the unit
when “SP B” is set to ZONE B, the sound is output from both
headphones and SPEAKERS B.
• If a DSP program is selected when “SP B” is set to ZONE B,
the unit automatically enters the Virtual CINEMA DSP mode.
■ Zone 2 setting E)ZONE2 SET
(U.S.A., Canada and Australia models only)
E)ZONE2 SET
ADVANCED
OPERATION
ZONE2 AMP;;;OFF
p
p
/ : Up/Down
-/+ : Select
Zone 2 amplifier ZONE2 AMP
Use to select how the ZONE 2 speakers will be amplified.
Choices: ON, OFF
• Select OFF if you do not use Zone 2 speakers or if you
connect your Zone 2 speakers through an external
amplifiers connected to this unit’s ZONE 2 OUTPUT
jacks.
• Select ON to use this unit’s internal amplifier if you
connect your Zone 2 speakers directly to this unit’s
PRESENCE/ZONE 2 speaker terminals.
English
61
00_RXV750_U_EN.book Page 62 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
REMOTE CONTROL FEATURES
In addition to controlling this unit, the remote control can also operate other A/V components made by YAMAHA and
other manufacturers. To control other components, you must set up remote control with the appropriate manufacturer
codes. This remote control also has a learn feature which allows the remote to acquire functions from other remote
controls equipped with an infrared remote control transmitter.
Control area
■ Controlling this unit
■ Controlling other components
The shaded areas below can be used to control this unit
after pressing AMP to activate the AMP mode.
The shaded areas below can be used to control other
components. Each button has a different function
depending on the selected component. Select the
component you want to control by pressing an input
selector button or SELECT k/n. The name of the selected
component appears in the display window.
TRANSMIT
RE-NAME
CLEAR
LEARN
SYSTEM
POWER
STANDBY
SLEEP
INPUT MODE
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
SELECT
Press AMP
to control
this unit.
POWER
POWER
TV
AV
The buttons in the
dotted lines control
this unit in any
mode. (SYSTEM
POWER,
STANDBY,
SLEEP, INPUT
MODE, MULTI CH
IN, VOLUME +/–
and MUTE)
AMP
REC
AUDIO
DISC SKIP
VOL
FREQ/RDS
EON
MODE
PTY SEEK
START
SET MENU
LEVEL
TITLE
MUTE
MENU
TV VOL
TV INPUT
A/B/C/D/E
CH
CH
TV MUTE
SELECT
PRESET
PRESET
TEST
ON SCREEN
A/B buttons and the input
selector buttons switch the
function of the component
control area below.
* Use the A/B buttons to
control other components
regardless of whether they
are connected to this unit.
Factory setting:
A...LD player
B...CD recorder
SELECT k/n switches
control to another
component without
changing the input source
on this unit.
RE-NAME
STANDBY
B
PHONO
MULTI CH IN
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
SELECT
POWER
TV
REC
JAZZ
ROCK
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
9
0
10
AV
AUDIO
DISC SKIP
VOLAUDIO
MODE
EX/ES
LEVEL
ENTER
Component control
area
You can control up to 11
different components by
setting appropriate
manufacturer codes (see
page 63).
Fixing the remote to AMP mode
You can fix the remote permanently to AMP mode (fixed AMP
mode) so that the shaded areas above always control this unit.
This is useful, if you primarily want to use the remote control in
AMP mode. To fix AMP mode, hold down AMP for at least 3
seconds so that “A:___” appears in the display window.
DVD
Component control mode
To temporarily switch to component control mode, press AMP.
To cancel fixed AMP mode, hold down AMP for at least 3
seconds.
62
DISC SKIP
EON
FREQ/RDS START
PTY SEEK
SET MENU
TITLE
TV INPUT
EON
MUTE
MENU
TV VOLMODE
LEVEL
START
PTY SEEK
A/B/C/D/E
SET MENU
TITLE
CH
PRESET
TEST
TV MUTE
TV INPUT
SELECT
MENU
CHTV VOL
A/B/C/D/E
PRESET
CH
TV MUTESTRAIGHT
ON SCREEN
SELECT
DISPLAY
PRESET
EFFECT
TEST
ON SCREEN
HALL
JAZZTV VOL ROCK
RETURN
DISPLAY
CH
TV VOL
RETURN
PRESET
STEREO
1
MUSIC
A:DVD
REC
FREQ/RDS
CHP/INDEX
Fixed AMP mode
POWER
TV
EFFECT
HALL
AMP
AV
POWER
DISPLAY
1
LEARN
INPUT MODE
A
POWER
STEREO
CLEAR
SLEEP
V-AUX
STRAIGHT
TV VOL
RETURN
TRANSMIT
SYSTEM
POWER
5
q/DTS
9
2
3
4
STEREO
HALL MOVIE
JAZZ
ENTERTAIN
TV THTR
6
1
7
2
3
8
MUSIC NIGHT
ENTERTAIN
TV THTR
PURE DIRECT
EX/ES
0
5
10 6
ENTER 7
ROCK
4
MOVIE
8
CHP/INDEX
q/DTS
PURE DIRECT
9
0
NIGHT
10
EX/ES
ENTER
CHP/INDEX
00_RXV750_U_EN.book Page 63 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
Setting manufacturer codes
2
You can control other components by setting the
appropriate manufacturer codes. Codes can be set up for
each input area.
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object.
“SETUP” and the selected component name appear
alternately in the display window.
The following table shows the factory preset component
(Library: component category) and the manufacturer code
for each area.
Input area
Component
category
(Library)
A
LD
LEARN
Manufacturer
Yamaha (U.K. and Europe models)
Yamaha-1 (Other models)
B
CD-R
PHONO
TV
–
V-AUX
VCR
–
Be sure to press and hold LEARN for at least 3
seconds, otherwise the learning process will start.
Yamaha
y
Complete each of the following steps in 30 seconds.
Otherwise, the learning mode will be automatically
canceled. In this case, press LEARN again.
Yamaha-3 (U.K. and Europe models)
Yamaha-1 (Other models)
TUNER
TUNER
MD/CD-R
MD
Yamaha-1
CD
CD
Yamaha-1
DTV/CBL
TV
–
VCR 1
VCR
–
DVR/VCR2
DVR
Yamaha
DVD
DVD
Yamaha-1
If you want to change a library (component
category), press j / i. You can set a different
type of component.
Library choices: L:DVD, L:DVR, L:LD, L:CD,
L:CDR, L:MD, L:TAP (tape), L:TUN, L:AMP*,
L:TV, L:CAB (cable), L:DBS, L:SAT, L:VCR
* The amplifier Library (L:AMP) code is preset to “YPC”
to operate this unit. However, you can switch between the
following two codes if necessary.
The initial setting for “Amplifier library” is “YPC”.
Note
You may not be able to operate your YAMAHA component even
if a YAMAHA manufacturer code is initially set as listed above.
In this case, try to set other YAMAHA manufacturer code(s).
1
YPC To operate this unit.
ZONE (U.S.A., Canada and Australia models only)
To operate ZONE 2 features.
Press an input selector button to select the
source component you want to set up.
PHONO
MULTI CH IN
B
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
Press u / d to select the name of your
component’s manufacturer.
You will find the names of most worldwide audiovideo manufacturers in alphabetical order in the
display window.
+
TV VOL
CH
–
TV MUTE
SELECT
PRESET
ADVANCED
OPERATION
A
3
CH
+
PRESET
TV VOL
–
English
63
00_RXV750_U_EN.book Page 64 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
4
Press one of the buttons shaded below to
see if you can control your component. If you
can, the manufacturer code is correct.
POWER
POWER
TV
AV
AMP
REC
AUDIO
DISC SKIP
VOL
FREQ/RDS
MODE
EON
PTY SEEK
START
SET MENU
LEVEL
TITLE
MUTE
MENU
TV VOL
TV INPUT
A/B/C/D/E
y
• If the manufacturer of your component has more than one
codes, try each of them until you find the correct one.
• If you continuously want to set up a code for another
component, press TV MUTE/SELECT and repeat steps 1,
3 and 4.
5
Press LEARN again to exit from the setup
mode.
LEARN
Notes
• The supplied remote control does not contain all possible
manufacturer codes for commercially available AV components
(including YAMAHA AV components). If operation is not
possible with any of the manufacturer codes, program the new
remote control function with the Learn feature (see below) or
use the remote control supplied with the component.
• If you have already programmed a remote control function for a
button, the function by learning programming takes priority
over the setup manufacturer code’s function.
• “ERROR” appears in the display window if you press a button
not indicated in the respective step, or when you press more
than one button at the same time.
64
00_RXV750_U_EN.book Page 65 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
Controlling other components
Once you set the appropriate manufacturer codes, you can
use this remote to control your other components. Note
that some buttons may not correctly operate the selected
component. Use the input selector buttons to select the
component you want to operate. The remote control
automatically switches to the appropriate control mode for
that component.
1
2
POWER
POWER
TV
AV
3
REC
AMP
AUDIO
DISC SKIP
VOL
FREQ/RDS
EON
MODE
4
5
6
PTY SEEK
TITLE
8
MUTE
TV INPUT
A/B/C/D/E
CH
TV MUTE
SELECT
CH
PRESET
ON SCREEN
TEST
STRAIGHT
TV VOL
RETURN
DISPLAY
EFFECT
STEREO
HALL
JAZZ
ROCK
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
6
7
8
PURE DIRECT
NIGHT
EX/ES
9
0
10
4
ENTER
7
8
9
0
A
A
DVD player/
VCR
DVD recorder
Digital TV/
Cable TV
LD player
CD player
MD/CD
recorder
Tuner
AV POWER
Power *1
Power *1
VCR power *3
Power *1
Power *1
Power *1
Power *1
TV POWER
TV power *2
TV power *2
TV power
TV power *2
TV power *2
TV power *2
TV power *2
REC/DISC
SKIP
Disc skip (player)
Rec (recorder)
Rec
VCR rec *3
Disc skip
Rec (MD)
h
Play
Play
VCR play *3
Play
Play
Play
ll
Search backward
Search backward
VCR search
backward *3
Search backward
Search backward
Search backward
hh
Search forward
Search forward
VCR search
forward *3
Search forward
Search forward
Search forward
AUDIO
Audio
e
Pause
b
Skip backward
a
Skip forward
Skip forward
Skip forward
Skip forward
s
Stop
Stop
VCR stop *3
Stop
Stop
Stop
TITLE/TV
INPUT
Title
TV input *2
TV input
TV input *2
TV input *2
TV input *2
TV MUTE
Select
TV mute *2
TV mute
TV mute *2
TV mute *2
TV mute *2
TV mute *2
TV VOL +
Up
TV volume + *2
TV volume +
TV volume + *2
TV volume + *2
TV volume + *2
TV volume + *2
Sound
Pause
VCR pause *3
Pause
Pause
Pause
Skip backward
Skip backward
Skip backward
TV input *2
TV VOL –
Down
TV volume – *2
TV volume –
TV volume – *2
TV volume – *2
TV volume – *2
TV volume – *2
CH +/i
Right
VCR channel +
TV channel +
TV channel + *2
TV channel + *2
TV channel + *2
Preset up
CH –/j
Left
VCR channel –
TV channel –
TV channel – *2
TV channel – *2
TV channel – *2
Preset down
RETURN
Return
1-9, 0, +10
Numeric buttons
Numeric buttons
Numeric buttons
Numeric buttons
Numeric buttons
Numeric buttons
MENU
Menu
DISPLAY
Display
ENTER
Title/Index
ADVANCED
OPERATION
5
6
0
MOVIE
5
q/DTS
CHP/INDEX
1
2
3
9
MENU
TV VOL
PRESET
7
START
SET MENU
LEVEL
Preset stations (1-8)
A/B/C/D/E
Enter
Display
Display
Display
Display
Enter
Chapter/Time
Index
Index
*1
This button functions only when the original remote control of the component has a POWER button.
These buttons can operate your TV without switching the input if the manufacturer code is set in DTV/CBL or PHONO. When the
manufacturer code for your TV is set up in both the DTV/CBL and PHONO areas, priority is given to the signal in the DTV/CBL
area.
*3 These buttons can operate your VCR without switching the input to VCR 1 if the manufacturer code is set in VCR 1.
*2
English
65
00_RXV750_U_EN.book Page 66 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
Programming codes from other
remote controls
3
If you want to program functions not included in the basic
operations covered by the manufacturer code, or an
appropriate manufacturer code is not available, do the
following. You can program any of the buttons available in
the component control area (see page 62). The buttons can
be programmed independently for each component.
Press LEARN using a ballpoint pen or similar
object.
Do not press and hold LEARN. If you hold it down
for more than three seconds, the remote enters the
manufacturer code setting mode.
LEARN
Note
This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn most
of its functions. However, you may not be able to program some
special signals or extremely long transmissions. (Refer to the
operating instructions for the remote control of your component.)
1
PHONO
y
Complete each of the following steps in 30 seconds.
Otherwise, the learning mode will be automatically
canceled. In this case, press LEARN again.
4
MULTI CH IN
A
B
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
Press the button at which you want to
program the new function.
“LEARN” is displayed.
MULTI CH IN
INPUT MODE
LEARN
SLEEP
CD
CLEAR
PHONO
DVD
RE-NAME
STANDBY
MD/CD-R
TRANSMIT
POWER
B
DVR/VCR2
SYSTEM
A
VCR 1
TUNER
AMP
SELECT
V-AUX
AV
POWER
VOL
DTV/CBL
TV
REC
POWER
EON
AUDIO
START
Place this remote control about 5 to 10 cm
apart from the other remote control on a flat
surface so that their infrared transmitters are
aimed at each other.
LEARN
INPUT MODE
CLEAR
SLEEP
CD
MULTI CH IN
RE-NAME
STANDBY
PHONO
TRANSMIT
POWER
B
MD/CD-R
SYSTEM
A
DVR/VCR2
DVD
VCR 1
TUNER
AMP
SELECT
V-AUX
AV
POWER
DTV/CBL
TV
POWER
5
Press and hold the button you want to
program on the other remote control until
“OK” appears in the display window.
LEARN
INPUT MODE
CLEAR
SLEEP
CD
MULTI CH IN
RE-NAME
STANDBY
PHONO
TRANSMIT
POWER
B
MD/CD-R
SYSTEM
A
DVR/VCR2
DVD
VCR 1
TUNER
AMP
SELECT
V-AUX
AV
POWER
DTV/CBL
TV
POWER
5 to 10 cm (2 to 4 in)
66
DISC SKIP
MODE
FREQ/RDS
2
Press an input selector button to select a
source component.
Flashes alternately
00_RXV750_U_EN.book Page 67 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
Notes
• “NG” appears in the display window if programming was
unsuccessful. In this case, start over from step 5.
• This remote control can learn approximately 120 functions.
However depending on the signals learned, “FULL” may
appear in the display before you program 120 functions. In this
case, clear unnecessary programmed functions to make room
for further learning.
6
Repeat steps 4 and 5 to program additional
functions.
7
Press LEARN again to exit from the learning
mode.
Changing source names in the
display window
You can change the name that appears in the display
window on the remote control if you want to use a
different name to the one that is set as the factory preset.
This is useful when you have set the input selector to
control a different component.
1
Press an input selector button to select the
source component you want to rename.
The selected component name appears in the display
window.
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
LEARN
Notes
• Learning may not be possible in the following cases:
– When the batteries in the remote control for this unit or other
components are weak.
– When the distance between the two remote controls is too
great or too small.
– When the remote control infrared windows are not facing at
the appropriate angle.
– When the remote control is exposed to direct sunlight.
– When the function to be programmed is continuous or
uncommon.
• “ERROR” appears in the display window if you press more than
one button at the same time.
2
3
Press RE-NAME using a
ballpoint pen or similar
object.
RE-NAME
Press u / d to select and enter a character.
Pressing d changes the character as follows:
A to Z, a to z, 0 to 9, space, -(hyphen), and /(slash).
(Pressing u changes the characters in reverse order.)
+
TV VOL
CH
–
CH
TV MUTE
SELECT
PRESET
+
PRESET
TV VOL
–
ADVANCED
OPERATION
4
Press j / i to move the cursor to the next
position.
+
TV VOL
CH
–
TV MUTE
SELECT
PRESET
CH
+
PRESET
TV VOL
–
y
If you want to continue setting up names for other
components, press TV MUTE/SELECT and repeat steps 1,
3 and 4.
Press RE-NAME again to exit from the
renaming mode.
English
5
RE-NAME
67
00_RXV750_U_EN.book Page 68 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
Clearing function sets
You can clear all changes made in each function set, such
as learned functions, renamed source names and setup
manufacturer codes.
4
Press CLEAR to exit from the clearing mode.
Once you have cleared a learned function for a
button, the button reverts to the factory preset setting.
CLEAR
1
Press CLEAR by using a ballpoint pen or
similar object.
CLEAR
y
Complete each of the following steps in 30 seconds. Other
wise, the learning mode will be automatically canceled. In
this case, press CLEAR again.
2
Press u / d to select the clear mode.
L:DVD (L: name of a component)
L:AMP
L:ALL
RNAME
FCTRY
3
Clears all learned functions in the respective
component control area. Press an input selector
button to select the component.
Clears all learned functions for this unit’s control
area.
Clears all learned functions.
Clears all renamed source names.
Clears all remote functions and returns the remote
to the factory settings.
Press and hold CLEAR again for about 3
seconds.
“C:OK” appears in the display window.
CLEAR
Note
“C:NG” appears in the display window if the operation is
unsuccessful. In this case, start over from step 2.
68
Note
“ERROR” appears in the display window under the following
circumstances:
– When a button other than the cursor is pressed.
– When more than one button is pressed at the same time.
00_RXV750_U_EN.book Page 69 Tuesday, February 17, 2004 10:08 AM
REMOTE CONTROL FEATURES
Clearing individual functions
4
Repeat step 3 to clear other learned
functions.
5
Press LEARN again to exit.
■ Clearing a learned function
You can clear the function learned in a certain
programmed button in each area.
1
2
Press an input selector button to select the
source component containing the function
you want to clear.
The selected component name appears in the display
window.
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
Press LEARN using a ballpoint pen or similar
object.
“LEARN” and the selected component name appear
alternately in the display window.
LEARN
y
Complete each of the following steps in 30 seconds.
Otherwise the learning mode will be automatically canceled.
In this case, press LEARN again.
Press and hold CLEAR using a ballpoint pen
or similar object, then press the button you
want to clear for about 3 seconds.
“C:OK” appears in the display window.
TRANSMIT
RE-NAME
CLEAR
ADVANCED
OPERATION
3
LEARN
SYSTEM
POWER
STANDBY
SLEEP
INPUT MODE
MULTI CH IN
A
B
PHONO
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
When you clear a learned function, the button reverts
to the factory preset setting (or manufacturer setting if
you have set manufacturer codes).
English
69
00_RXV750_U_EN.book Page 70 Tuesday, February 17, 2004 10:08 AM
ZONE 2 (U.S.A., CANADA AND AUSTRALIA MODELS ONLY)
ZONE 2
(U.S.A., CANADA AND AUSTRALIA MODELS ONLY)
This unit allows you to configure a multi-room audio system. You can control this unit from the second room using the
supplied remote control.
Only analog signals are sent to the second room. Any source you want to listen to in the second room must be
connected using the analog (AUDIO L/R) input jacks on this unit.
Zone 2 connections
You need the following additional equipment to use the multi-room functions of this unit:
• An infrared signal receiver in the second room.
• An infrared emitter in the main room. This emitter transmits the infrared signals from the remote control in the second
room to the main room (to a CD player, for example).
• An amplifier and speakers for the second room.
y
• Since there are many possible ways to connect and use this unit in a multi-room installation, we recommend that you consult with the
nearest authorized YAMAHA dealer or service center for the Zone 2 connections which will best meet your requirements.
• Some YAMAHA models are able to connect directly to the REMOTE CONTROL OUT jack of this unit. If you own these products,
you may not need to use an infrared emitter. Up to 6 YAMAHA components can be connected as shown.
OUT
IN
OUT
IN
REMOTE
CONTROL OUT
This unit
•
■ System configuration and connections example
ZONE 2 OUTPUT
Amplifier
DVD player
(or other component)
This unit
Remote control
DVD INPUT
Infrared emitter
Main room
REMOTE CONTROL OUT
Infrared signal
receiver
Second room
ZONE 2 REMOTE IN
Notes
• When not using the main room, turn down the volume of this unit in the main room. Adjust the ZONE 2 volume using the amplifier in
the second room.
• To avoid unexpected noise, DO NOT USE the Zone 2 feature with CDs encoded in DTS.
70
00_RXV750_U_EN.book Page 71 Tuesday, February 17, 2004 10:08 AM
ZONE 2 (U.S.A., CANADA AND AUSTRALIA MODELS ONLY)
Using this unit’s internal amplifier
To use this unit’s internal amplifier, set “ZONE2 AMP” to ON in SET MENU (see page 61).
–
+
L
R
PRESENCE
/ZONE 2
Second room
This unit
Remote controlling Zone 2
4
The supplied remote control can be used to control Zone
2. You can even select the input source and control
components located in the main room directly from the
second room regardless of the listening condition in the
main room.
■ To enable Zone 2 mode on the remote
control
You will be able to switch the remote control mode from
one room to another, and use STANDBY, SYSTEM
POWER, MUTE and VOL –/+ to control the selected
room.
Press LEARN to complete the Zone setup.
The remote control will be able to operate this unit
and Zone 2.
LEARN
■ To control Zone 2
1
Press SELECT k repeatedly to display
“ZONE2” in the display window.
SELECT
1
Repeat steps 1 and 2 of the procedure in
“Setting manufacturer codes” on page 63.
2
Press j / i to select “L:AMP”.
+
TV VOL
–
TV MUTE
SELECT
CH
+
PRESET
TV VOL
–
3
2
Press SYSTEM POWER to turn Zone 2 power
on.
ADVANCED
OPERATION
CH
PRESET
Press u / d to select “ZONE”.
+
TV VOL
CH
–
TV MUTE
SELECT
PRESET
CH
+
PRESET
TV VOL
–
English
71
00_RXV750_U_EN.book Page 72 Tuesday, February 17, 2004 10:08 AM
ZONE 2 (U.S.A., CANADA AND AUSTRALIA MODELS ONLY)
■ Turning this unit to either on or standby
3
4
Press an input selector button to select the
input source you want to listen to in the
second room.
The display window shows “2: name of selected
input” if the remote control is in the Zone 2 mode.
PHONO
MULTI CH IN
A
B
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
You can control Zone 2 using the input
selector, STANDBY, SYSTEM POWER, MUTE
and VOL –/+ buttons.
REC
TRANSMIT
RE-NAME
CLEAR
AUDIO
DISC SKIP
STANDBY
SLEEP
LCD display
SYSTEM POWER/
STANDBY
Normal mode*
Name of component
Turns the main unit
on/standby
Zone 2 mode
“ZONE2” or “2:name
of component”
Turns Zone 2 to on/
standby
System mode
“SYSTM”
Turns everything (the
main unit and Zone
2) on/standby
*
LEARN
SYSTEM
POWER
SYSTEM POWER and STANDBY work differently
depending on the selected mode that appears on the
display window.
• When normal, Zone2 mode is selected, you can turn
the main unit, Zone 2 to on/standby individually.
• When system mode is selected, or when YPC is
selected as the amplifier library (L:AMP) code, you
can turn the main unit, Zone 2 to on/standby all
together simultaneously.
INPUT MODE
VOL
FREQ/RDS
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
MODE
*
EON
PTY SEEK
START
LEVEL
SET MENU
TITLE
MENU
MUTE
“MAIN” appears for a few seconds when SYSTEM POWER
or STANDBY is pressed.
TV VOL
TV INPUT
DTV/CBL
VCR 1
DVR/VCR2
A/B/C/D/E
■ Special considerations for DTS software
DVD
CH
TV MUTE
SELECT
CH
PRESET
PRESET
ON SCREEN
TEST
STRAIGHT
TV VOL
RETURN
DISPLAY
EFFECT
* If “ZONE2 AMP” in OPTION MENU is set to ON, you
can use VOL –/+ to adjust sound output from speakers
connected to the PRESENCE/ZONE 2 speaker terminals
(see page 61). However, VOL –/+ cannot be used to
adjust sound output from the ZONE2 OUTPUT jacks.
5
Press SELECT k/n to exit from the Zone 2
mode.
Notes
• “ZONE2” will appear in the display window only when k is
pressed, and SYSTM only when n is pressed.
• If you press SELECT k when the unit is set to Zone 2 mode, the
unit switches to Zone 3 mode. However, this unit does not
support Zone 3 mode. To exit Zone 3 mode, press SELECT n.
72
The DTS signal is a digital bitstream. If you attempt to
send the DTS signal to the second room you will only hear
digital noise (that may damage your speakers). Thus, the
following considerations and adjustments need to be made
when playing DTS-encoded discs.
For DVDs encoded in DTS
Only 2 channel analog audio signals may be sent to the
second room.
Use the disc menu to set the DVD player’s mixed 2channel left and right audio outputs to the PCM or Dolby
Digital soundtrack.
For CDs encoded in DTS
To avoid unexpected noise, DO NOT USE the Zone 2
feature with CDs encoded in DTS.
00_RXV750_U_EN.book Page 73 Tuesday, February 17, 2004 10:08 AM
EDITING SOUND FIELD PARAMETERS
EDITING SOUND FIELD PARAMETERS
What is a sound field
What really creates the rich, full tones of a live instrument
are the multiple reflections from the walls of the room. In
addition to making the sound “live”, these reflections
enable us to tell where the player is situated, and the size
and shape of the room in which we are sitting.
Changing parameter settings
You can enjoy good quality sound with the factory preset
parameters. Although you do not have to change the initial
settings, you can change some of the parameters to better
suit the input source or your listening room.
TV
■ Elements of a sound field
TRANSMIT
RE-NAME
CLEAR
AUDIO
DISC SKIP
SYSTEM
In any environment, in addition to the direct sound coming
straight to our ears from the player’s instrument, there are
two distinct types of sound reflections that combine to
make up the sound field:
POWER
STANDBY
SLEEP
INPUT MODE
A
B
PHONO
MULTI CH IN
V-AUX
TUNER
MD/CD-R
CD
DTV/CBL
VCR 1
DVR/VCR2
DVD
VOL
FREQ/RDS
MODE
If you could create the appropriate early reflections and
subsequent reverberations in your listening room, you
would be able to create your own listening environment.
The acoustics in your room could be changed to those of a
concert hall, a dance floor, or virtually any size room at
all. This ability to create sound fields at will is exactly
what YAMAHA has done with the digital sound field
processor.
START
PTY SEEK
SET MENU
LEVEL
TITLE
MUTE
MENU
TV VOL
A/B/C/D/E
CH
SELECT
Direct sound, early reflections and subsequent
reverberation taken together help us to determine the
subjective size and shape of the room, and it is this
information that the digital sound field processor
reproduces in order to create sound fields.
EON
TV INPUT
Early reflections
Reflected sounds reach our ears extremely rapidly (50 ms
– 100 ms after the direct sound), after reflecting from one
surface only — for example, from the ceiling or a wall.
Early reflections actually add clarity to the direct sound.
Reverberations
These are caused by reflections from more than one
surface — walls, ceiling, the back of the room — so
numerous that they merge together to form a continuous
sonic “afterglow”. They are non-directional, and lessen
the clarity of the direct sound.
AV
REC
LEARN
1
POWER
POWER
TV
AV
PRESET
TEST
ON SCREEN
STRAIGHT
TV VOL
5
AMP
CH
TV MUTE
SELECT
PRESET
RETURN
DISPLAY
4
2
EFFECT
STEREO
HALL
1
2
3
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
EX/ES
9
0
REC
JAZZ
10
ROCK
3
ENTER
CHP/INDEX
1
Press AMP.
AMP
2
3
Turn on the video monitor and
press ON SCREEN repeatedly
to select the full display
mode.
ON SCREEN
DISPLAY
Select the sound field program you want to
adjust.
STEREO
HALL
JAZZ
1
2
3
ROCK
4
MUSIC
ENTERTAIN
TV THTR
MOVIE
5
6
7
8
q/DTS
PURE DIRECT
NIGHT
9
0
EX/ES
ENTER
10
CHP/INDEX
ADDITIONAL
INFORMATION
Program No.
Program name
P08 MOVIE THEATER
Cursor
.General
DSPLEVEL;;;;0dB
P.INIT.DLY;;15ms
P.ROOMSIZE;;1.0
S.INIT.DLY;;20ms
S.ROOMSIZE;;1.0
English
Parameters
Parameter values
73
00_RXV750_U_EN.book Page 74 Tuesday, February 17, 2004 10:08 AM
EDITING SOUND FIELD PARAMETERS
4
Press u / d to select
the parameters.
+
TV VOL
CH
–
TV MUTE
SELECT
PRESET
CH
+
PRESET
TV VOL
–
5
6
Press j / i to change
the parameter value.
When you set a parameter
to a value other than the
factory-set value, an
asterisk mark (*) appears
by the parameter name on
the front panel display.
+
TV VOL
CH
–
TV MUTE
SELECT
PRESET
CH
+
PRESET
TV VOL
–
Repeat steps 3 through 5 as necessary to
change other program parameters.
Note
You cannot change parameter values when “MEMORY GUARD”
is set to ON. If you want to change the parameter values, set
“MEMORY GUARD” to OFF (see page 60).
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is set in the standby
mode, the power cord is disconnected from the AC
outlet, or the power supply is temporarily cut due to
power failure. However, if the power is cut for more
than one week, the parameter values will return to the
factory settings. If this happens, edit the parameter
value again.
■ Resetting parameters to the factory
presets
To reset a certain parameter
Select the parameter you want to reset, then press j / i
repeatedly until the asterisk mark (*) next to the parameter
name disappears.
To reset all parameters
Use PARAM. INI (see page 61).
74
00_RXV750_U_EN.book Page 75 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PARAMETER DESCRIPTIONS
SOUND FIELD PARAMETER DESCRIPTIONS
You can adjust the values of certain digital sound field parameters so the sound fields are recreated accurately in your
listening room. Not all of the following parameters are found in every program.
■ DSP LEVEL
Function:
Description:
Control range:
This parameter adjusts the level of all the DSP effect sounds within a narrow range.
Depending on the acoustics of your listening room, you may want to increase or decrease the DSP
effect level relative to the level of the direct sound.
–6 dB – +3 dB
■ INIT. DLY (Initial delay)
Function:
Description:
Control range:
This parameter changes the apparent distance from the source sound by adjusting the delay between the
direct sound and the first reflection heard by the listener.
The smaller the value, the closer the sound source seems to the listener. The larger the value, the farther
it seems. For a small room, set to a small value. For a large room, set to a large value.
1 – 99 msec
Source Sound
Level
Level
Level
Early
Reflections
Time
Time
Time
INIT. DLY
INIT. DLY
INIT. DLY
Sound Source
Reflection Face
Small value = 1 ms
Large value = 99 ms
■ ROOM SIZE/P. ROOM SIZE (Room size)
Function:
Description:
Control range:
This parameter adjusts the apparent size of the surround sound field. The larger the value, the larger the
surround sound field becomes.
As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between
the original reflected sound and the subsequent reflections. By controlling the time between the
reflected sounds, you can change the apparent size of the virtual venue. Changing this parameter from
one to two, doubles the apparent length of the room.
0.1 – 2.0
Time
Level
Level
Time
Early
Reflections
ADDITIONAL
INFORMATION
Level
Source Sound
Time
Sound Source
English
Small value = 0.1
Large value = 2.0
75
00_RXV750_U_EN.book Page 76 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PARAMETER DESCRIPTIONS
■ LIVENESS
Function:
Description:
Control range:
This parameter adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the
early reflections decay.
The early reflections of a sound source decay much faster in a room with acoustically absorbent wall
surfaces than in one which has highly reflective surfaces. A room with acoustically absorbent surfaces
is referred to as “dead”, while a room with highly reflective surfaces is referred to as “live”. The
LIVENESS parameter lets you adjust the early reflection decay rate, and thus the “liveness” of the
room.
0 – 10
Source Sound
Time
Small Reflected
Sound
Small value = 0
Level
Dead
Level
Level
Live
Time
Time
Large
Reflected Sound
Large value = 10
■ S. INIT. DLY (Surround initial delay)
Function:
This parameter adjusts the delay between the direct sound and the first reflection on the surround side of
the sound field. You can only adjust this parameter when at least two front channels and two surround
channels are used.
Control Range: 1 – 49 msec
■ S. ROOM SIZE (Surround room size)
Function:
This parameter adjusts the apparent size of the surround sound field.
Control Range: 0.1 – 2.0
■ S. LIVENESS (Surround liveness)
Function:
This parameter adjusts the apparent reflectivity of the virtual walls in the surround sound field.
Control Range: 0 – 10
■ SB INIT. DLY (Surround back initial delay)
Function:
This parameter adjusts the delay between the direct sound and the first reflection in the surround back
sound field.
Control Range: 1 – 49 msec
■ SB ROOM SIZE (Surround back room size)
Function:
This parameter adjusts the apparent size of the surround back sound field.
Control Range: 0.1 – 2.0
■ SB LIVENESS (Surround back liveness)
Function:
This parameter adjusts the apparent reflectivity of the virtual wall in the surround back sound field.
Control Range: 0 – 10
76
00_RXV750_U_EN.book Page 77 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PARAMETER DESCRIPTIONS
■ REV.TIME (Reverberation time)
Function:
This parameter adjusts the amount of time it takes for the dense, subsequent reverberation sound to
decay by 60 dB (at 1 kHz). This changes the apparent size of the acoustic environment over an
extremely wide range.
Description:
Set a longer reverberation time for “dead” sources and listening room environments, and a shorter time
for “live” sources and listening room environments.
Control Range: 1.0 – 5.0 sec
Source Sound
Reverberation
Reverberation
Early Reflections
60 dB
60 dB
REV.TIME
Sound Source
REV.TIME
60 dB
REV.TIME
Long
Reverberation
Short
Reverberation
Large value = 5.0 s
Small value = 1.0 s
■ REV.DELAY (Reverberation delay)
This parameter adjusts the time difference between the beginning of the direct sound and the beginning
of the reverberation sound.
Description:
The larger the value, the later the reverberation sound begins. A later reverberation sound makes you
feel like you are in a larger acoustic environment.
Control Range: 0 – 250 msec
Level
Function:
Source Sound
(dB)
60 dB
Reverberation
Time
REV.DELAY
REV.TIME
■ REV. LEVEL (Reverberation level)
ADDITIONAL
INFORMATION
Function:
This parameter adjusts the volume of the reverberation sound.
Description:
The larger the value, the stronger the reverberation becomes.
Control Range: 0 – 100%
Level
Source Sound
REV. LEVEL
English
Time
77
00_RXV750_U_EN.book Page 78 Tuesday, February 17, 2004 10:08 AM
SOUND FIELD PARAMETER DESCRIPTIONS
■ DIALG.LIFT (Dialog lift)
Function:
Description:
Choices:
This parameter adjusts the height of the front and center channel sounds by assigning some of the front
and center channel elements to the presence speakers.
The larger the parameter, the higher the position of the front and center channel sound.
0/1/2/3/4/5, initial setting is 3.
For 7ch Stereo
Function:
These parameter adjusts the volume level for each channel in 7-channel stereo mode.
Control Range: 0 – 100%
■ CT LEVEL (Center level)
■ SL LEVEL (Surround left level)
■ SR LEVEL (Surround right level)
■ SB LEVEL (Surround back level)
■ PR LEVEL (Presence level)
For PRO LOGIC IIx Music and PRO LOGIC II Music
■ PANORAMA
Function:
Choices:
Extends the front stereo image to include the surround speakers for wraparound effect.
OFF/ON, initial setting is OFF.
■ DIMENSION
Function:
Control range:
Gradually adjusts the sound field either towards the front or towards the rear.
–3 (towards the rear) to +3 (towards the front), initial setting is STD (standard).
■ CT WIDTH (Center width)
Function:
Control range:
Adjusts the center image from all three front speakers to varying degrees. A larger value adjusts the
center image towards the front left and right speakers.
0 (center channel sound is output only from center speaker) to 7 (center channel sound is output only
from front left and right speakers), initial setting is 3.
For PRO LOGIC IIx Movie, Music and Game
■ PLII/PLIIx (Pro Logic II/Pro Logic IIx)
Function:
Choices:
Switches the type of Pro Logic decoding to be used. PLII decoding creates 5.1-channel sound from 2channel sources. PLIIx decoding creates 6.1/7.1-channel sound from 2-channel sources.
PLII, PLIIx
For DTS Neo:6 Music
■ C. IMAGE (Center image)
Function:
Control range:
78
This parameter adjusts the center image from all three front speakers to varying degrees.
0 – 0.5
00_RXV750_U_EN.book Page 79 Tuesday, February 17, 2004 10:08 AM
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and contact the
nearest authorized YAMAHA dealer or service center.
■ General
Problem
This unit fails to turn
on when STANDBY/
ON (or SYSTEM
POWER) is pressed,
or enters in the
standby mode soon
after the power has
been turned on.
On-screen display
does not appear.
No sound
Remedy
Refer to
page
The power cord is not connected or the
plug is not completely inserted.
Connect the power cord firmly.
—
The impedance setting is incorrect.
Set the impedance to match your speakers.
24
The protection circuitry has been
activated.
Make sure all speaker wire connections on this unit
and on all speakers are secure and that the wire for
each connection does not touch anything other than
its respective connection.
This unit has been exposed to a strong
external electric shock (such as lightning
and strong static electricity).
Set this unit in the standby mode, disconnect the
power cord, plug it back in after 30 seconds, then use
it normally.
—
The setting for the on-screen display is set
to “DISPLAY OFF”.
Select the full display or short display mode.
49
“GRAY BACK” in SET MENU is set to
OFF, and no video signal is currently
being received.
Set “GRAY BACK” to AUTO to always show the
OSD.
60
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
The optimizer microphone is connected.
Disconnect the optimizer microphone.
26
The input mode is set to DTS or
ANALOG.
Select AUTO.
37
No appropriate input source has been
selected.
Select an appropriate input source with INPUT,
MULTI CH INPUT or the input selector buttons.
31
Speaker connections are not secure.
Secure the connections.
13
The front speakers to be used have not
been selected properly.
Select the front speakers with SPEAKERS A and/or
B.
31
The volume is turned down.
Turn up the volume.
—
The sound is muted.
Press MUTE or any operation buttons of this unit to
cancel a mute and adjust the volume.
32
The input mode is set to ANALOG while
playing a source encoded with a DTS
signal.
Set the input mode to AUTO or DTS.
37
The signals this unit cannot reproduce are
being received from a source component
e.g.: a CD-ROM.
Play a source whose signals this unit can reproduce.
—
The output and input for the picture are
connected to different types of video
jacks.
Turn on the video conversion function.
60
13-15
17-20
ADDITIONAL
INFORMATION
No picture
Cause
English
79
00_RXV750_U_EN.book Page 80 Tuesday, February 17, 2004 10:08 AM
TROUBLESHOOTING
Problem
The sound suddenly
goes off.
Cause
Remedy
Refer to
page
Check that the impedance selector setting is correct.
24
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned the unit off.
Turn on the power, and play the source again.
—
The sound is muted.
Press MUTE to cancel a mute.
32
Only the speaker on
one side can be
heard.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
13
Incorrect balance settings in SET MENU.
Adjust the SPEAKER LEVEL settings.
56
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound from the
effect speakers.
The sound field programs are turned off.
Press STRAIGHT (EFFECT) to turn them on.
37
You are using a source or program
combination that does not output sound
from all channels.
Try another sound field program.
45
The output level of the center speaker is
set to minimum.
Raise the level of the center speaker.
56
“CENTER SP” in SET MENU is set to
NONE.
Select the appropriate setting for the center speaker.
54
One of the Hi-Fi DSP programs (except
for 7ch Stereo) has been selected.
Try another sound field program.
45
The output level of the surround speakers
is set to minimum.
Raise the output level of the surround speakers.
56
“SURR L/R SP” in SET MENU is set to
NONE.
Select the appropriate setting for the surround left and
right speakers.
54
A monaural source is being played with
STRAIGHT.
Press STRAIGHT (EFFECT) to turn on the sound
fields.
—
Presence speakers are selected.
Select surround back speakers in PR/SB SELECT.
58
“SURR L/R SP” in SET MENU is set to
NONE.
If the surround left and right speakers are set to
NONE, the surround back speaker setting is
automatically set to NONE. Select the appropriate
setting for the surround speakers.
54
“SURR B L/R SP” in SET MENU is set to
NONE.
Select LRGx1 or SMLx1.
55
“LFE/BASS OUT” in SET MENU is set
to FRNT when a Dolby Digital or DTS
signal is being played.
Select SWFR or BOTH.
55
“LFE/BASS OUT” in SET MENU is set
to SWFR or FRNT when a 2-channel
source is being played.
Select BOTH.
55
No sound from the
center speaker.
No sound from the
surround speakers.
No sound from the
surround back
speakers.
No sound from the
subwoofer.
The protection circuitry has been activated
because of a short circuit, etc.
The source does not contain low bass
signals.
80
00_RXV750_U_EN.book Page 81 Tuesday, February 17, 2004 10:08 AM
TROUBLESHOOTING
Problem
Cause
Remedy
Refer to
page
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator on
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operations
instructions for your component.
—
The input mode is set to ANALOG.
Set the input mode to AUTO or DTS.
37
A “humming” sound
can be heard.
Incorrect cable connections.
Firmly connect the audio plugs. If the problem
persists, the cables may be defective.
—
No connection from the turntable to the
GND terminal.
Connect the grounding cord of your turnable to the
GND terminal of this unit.
20
The volume level is
low while playing a
record.
The record is being played on a turntable
with an MC cartridge.
The turntable should be connected to this unit through
an MC-head amplifier.
20
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the OUT
(REC) jacks of this unit is turned off.
Turn on the power to the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by a digital
recording component
connected to this
DIGITAL OUTPUT
jack.
The source component is not connected to
this unit’s DIGITAL INPUT jacks.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT jacks.
Connect the source component to the DIGITAL
INPUT jacks.
17-20, 44
The source component is not connected to
this unit’s analog AUDIO IN jacks.
Connect the source component to the analog AUDIO
IN jacks.
17-20, 44
The sound field
parameters and some
other settings on this
unit cannot be
changed.
“MEMORY GUARD” in SET MENU is
set to ON.
Select OFF.
60
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the AC power cord from the outlet and
then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short circuited.
Make sure all speaker cables are connected correctly.
13
Some components cannot record the
Dolby Digital or DTS sources.
ADDITIONAL
INFORMATION
English
81
00_RXV750_U_EN.book Page 82 Tuesday, February 17, 2004 10:08 AM
TROUBLESHOOTING
Problem
Cause
Remedy
There is noise
interference from
digital or highfrequency equipment,
or this unit.
This unit is too close to the digital or highfrequency equipment.
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
There is noise when
the OSD is displayed.
This unit suddenly
turns into the standby
mode.
Refer to
page
Move this unit further away from such equipment.
—
The OSD may be disturbed when
displaying OSD through component video
connections.
Select OFF in CMPNT OSD.
60
The internal temperature becomes too
high and the overheat protection circuitry
has been activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
—
■ Tuner
Problem
FM stereo reception is
noisy.
FM
AM
82
Cause
Remedy
Refer
to page
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Check the antenna connections.
Try using a high-quality directional FM
antenna.
22
Use the manual tuning method.
40
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multipath interference.
Adjust the antenna position to eliminate
multipath interference.
—
The desired station
cannot be tuned in with
the automatic tuning
method.
The signal is too weak.
Use a high-quality directional FM antenna.
22
Use the manual tuning method.
40
Previously preset
stations can no longer
be tuned in.
This unit has been disconnected for a
long period.
Preset the stations again.
40
The desired station
cannot be tuned in with
the automatic tuning
method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for best reception.
—
Use the manual tuning method.
40
There are continuous
crackling and hissing
noises.
Noises result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
—
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV.
—
00_RXV750_U_EN.book Page 83 Tuesday, February 17, 2004 10:08 AM
TROUBLESHOOTING
■ Remote control
Problem
The remote control
does not work nor
function properly.
The remote control
does not “learn” new
functions.
Cause
Remedy
Refer to
page
Wrong distance or angle.
The remote control will function within a maximum
range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel.
8
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
3
The manufacturer code was not correctly
set.
Set the manufacturer code correctly.
63
Try setting another code for the same manufacturer.
63
Even if the manufacturer code is correctly
set, there are some models that do not
respond to the remote control.
Program the necessary functions independently into
the programmable buttons using the Learn feature.
66
The batteries of this remote control and/or
the other remote control are too weak.
Replace the batteries.
3
The distance between the two remote
controls is too much or too little.
Place the remote controls at the proper distance.
66
The signal coding or modulation of the
other remote control is not compatible
with this remote control.
Learning is not possible.
—
Memory capacity is full.
Delete other unnecessary functions to make room for
the new functions.
69
ADDITIONAL
INFORMATION
English
83
00_RXV750_U_EN.book Page 84 Tuesday, February 17, 2004 10:08 AM
RESETTING THE FACTORY PRESETS
RESETTING THE FACTORY PRESETS
If you want to reset all of your unit’s parameters for any
reason, do the following. This procedure completely resets
ALL parameters, including the SET MENU, level, assign
and tuner presets.
Be sure this unit is in standby mode.
(U.S.A. model)
VOLUME
OPTIMIZER
MIC
PRESET/TUNING
FM/AM
EDIT
A/B/C/D/E
l PRESET/TUNING h
NEXT
LEVEL
PROGRAM
MEMORY
TUNING MODE
MAN'L/AUTO FM
AUTO/MAN'L MONO
INPUT
PHONES
SPEAKERS
A
B
STRAIGHT
TONE CONTROL
INPUT MODE
MULTI CH
INPUT
PURE DIRECT
STANDBY
/ON
VIDEO AUX
EFFECT
SILENT CINEMA
S VIDEO
STANDBY/ON
1
VIDEO
L
AUDIO
R
OPTICAL
STRAIGHT (EFFECT)
Hold down STRAIGHT (EFFECT) on the front
panel and press STANDBY/ON.
“FACTORY PRESET” appears in the front panel
display.
y
To cancel the initialization procedure without making any
changes, press STANDBY/ON.
2
Press STRAIGHT (EFFECT) to select the
desired setting.
Reset
Cancel
3
84
To reset the unit to its factory presets.
To cancel without making any changes.
Press STANDBY/ON to confirm your
selection.
If you selected “Reset”, the unit is reset to its factory
presets and switches to standby mode.
If you selected “Cancel”, the unit switches to standby
mode and nothing is reset.
00_RXV750_U_EN.book Page 85 Tuesday, February 17, 2004 10:08 AM
GLOSSARY
GLOSSARY
Audio formats
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (left, center, and right), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (low frequency effect), the system has
a total of 5.1-channels (LFE is counted as 0.1 channel). By
using 2-channel stereo for the surround speakers, more
accurate moving sound effects and surround sound
environment are possible than with Dolby Surround. The
wide dynamic range (from maximum to minimum
volume) reproduced by the 5 full-range channels and the
precise sound orientation generated using digital sound
processing provide listeners with previously unheard of
excitement and realism.
With this unit, any sound environment from monaural up
to a 5.1-channel configuration can be freely selected for
your enjoyment.
■ Dolby Digital Surround EX
Dolby Digital EX creates 6 full-bandwidth output
channels from 5.1-channel sources. This is done using a
matrix decoder that derives 3 surround channels from the
2 in the original recording. For the best results, Dolby
Digital EX should be used with movie sound tracks
recorded with Dolby Digital Surround EX. With this
additional channel, you can experience more dynamic and
realistic moving sound especially with scenes with
“flyover” and “fly-around” effects.
■ Dolby Pro Logic II
■ Dolby Pro Logic IIx
Dolby Pro Logic IIx is a new technology enabling discrete
multi-channel playback from 2-channel or multi-channel
sources. There is a Music mode for music, a Movie mode
for movies and a Game mode for games.
Dolby Surround uses a 4 channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range.
Dolby Surround is widely used with nearly all video tapes
and laser discs, and in many TV and cable broadcasts as
well. The Dolby Pro Logic decoder built into this unit
employs a digital signal processing system that
automatically stabilizes the volume on each channel to
enhance moving sound effects and directionality.
■ DTS 96/24
DTS 96/24 offers an unprecedented level of audio quality
for multi-channel sound on DVD-Video, and is fully
backward-compatible with all DTS decoders. “96” refers
to a 96 kHz sampling rate (compared to the typical 48 kHz
sampling rate). “24” refers to 24-bit word length. DTS 96/
24 offers sound quality transparent to the original 96/24
master, and 96/24 5.1-channel sound with full-quality fullmotion video for music programs and motion picture
soundtracks on DVD-video.
■ DTS (Digital Theater Systems)
Digital Surround
DTS digital surround was developed to replace the analog
soundtracks of movies with a 6-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. Digital Theater Systems Inc.
has developed a home theater system so that you can enjoy
the depth of sound and natural spatial representation of
DTS digital surround in your home. This system produces
practically distortion-free 6-channel sound (technically, a
left, right and center channels, 2 surround channels, plus
an LFE 0.1 channel as a subwoofer, for a total of 5.1channels). The unit incorporates DTS-ES decoder that
enables 6.1- channel reproduction by adding the surround
back channel to existing 5.1-channel format.
■ Neo:6
Neo:6 decodes the conventional 2-channel sources for 6
channel playback by the specific decoder. It enables
playback with the full-range channels with higher
separation just like digital discrete signal playback. Two
modes are available; “Music mode” for playing music
sources and “Cinema mode” for movies.
ADDITIONAL
INFORMATION
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround software.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels (instead of
only 1 surround channel for conventional Pro Logic
technology). Music and Game modes are also available for
2-channel sources in addition to the Movie mode.
■ Dolby Surround
English
85
00_RXV750_U_EN.book Page 86 Tuesday, February 17, 2004 10:08 AM
GLOSSARY
Sound field programs
Audio information
■ CINEMA DSP
■ ITU-R
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers and designed
for acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it’s inevitable that there are differences in
the sound heard as well. Based on a wealth of actually
measured data, YAMAHA CINEMA DSP uses
YAMAHA original sound field technology to combine
Dolby Pro Logic, Dolby Digital and DTS systems to
provide the visual and audio experience of movie theater
in the listening room of your own home.
ITU-R is the radio communication sector of the ITU
(International Telecommunication Union). ITU-R
recommends a standard speaker placement which is used
in many critical listening rooms, especially for mastering
purposes.
■ SILENT CINEMA
YAMAHA has developed a natural, realistic sound effect
DSP algorithm for headphones.
Parameters for headphones have been set for each sound
field so that accurate representations of all the sound field
programs can be enjoyed on headphones.
■ Virtual CINEMA DSP
YAMAHA has developed a Virtual CINEMA DSP
algorithm that allows you to enjoy DSP sound field
surround effects even without any surround speakers by
using virtual surround speakers.
It is even possible to enjoy Virtual CINEMA DSP using a
minimal two-speaker system that does not include a center
speaker.
86
■ LFE 0.1 channel
This channel is for the reproduction of low bass signals.
The frequency range for this channel is 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low frequency range compared to the full-range
reproduced by the other 5/6 channels in Dolby Digital or
DTS 5.1/6.1-channel systems.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “pulse code
modulation”, the analog signal is encoded as pulses and
then modulated for recording.
■ Sampling frequency and number of
quantized bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits.
The range of rates that can be played back is determined
based on the sampling rate, while the dynamic range
representing the sound level difference is determined by
the number of quantized bits. In principle, the higher the
sampling frequency, the wider the range of frequencies
that can be played back, and the higher the number of
quantized bits, the more finely the sound level can be
reproduced.
00_RXV750_U_EN.book Page 87 Tuesday, February 17, 2004 10:08 AM
GLOSSARY
Video signal information
■ Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal.
A monitor with component input jacks is required in order
to use the component signal for output.
■ Composite video signal
With the composite video signal system, the video signal
is composed of three basic elements of a video picture;
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
■ S-Video signal
With the S-Video signal system, the video signal normally
transmitted using a pin cable is separated and transmitted
as the Y signal for the luminance and the C signal for the
chrominance through the S-Video cable. Using the S
VIDEO jack eliminates video signal transmission loss and
allows recording and playback of even more beautiful
images.
ADDITIONAL
INFORMATION
English
87
RXV750_U_cv.fm Page 1 Monday, January 19, 2004 10:04 AM
U
SPECIFICATIONS
AUDIO SECTION
VIDEO SECTION
• Minimum RMS Output Power for Front, Center, Surround,
Surround back
20 Hz to 20 kHz, 0.06% THD, 8 Ω .................................... 100 W
• Video Signal Type ......................................................... PAL/NTSC
• Maximum Power (EIAJ)
[China, Korea and General models]
1 kHz, 10% THD, 8 Ω ....................................................... 140 W
• Dynamic Power (IHF)
8/6/4/2 Ω .......................................................135/170/200/245 W
• DIN Standard Output Power [U.K., Europe and Asia models]
1 kHz, 0.7% THD, 4 Ω ...................................................... 150 W
• IEC Output Power [U.K., Asia and Europe models]
1 kHz, 0.06% THD, 8 Ω .................................................... 110 W
• Signal to Noise Ratio ............................................................. 50 dB
• Frequency Response (MONITOR OUT)
Composite, S-Video ................................ 5 Hz to 10 MHz, –3 dB
Component ............................................. 5 Hz to 60 MHz, –3 dB
FM SECTION
• Tuning Range
[U.S.A. and Canada models] ......................... 87.5 to 107.9 MHz
[Asia and General model] ........ 87.5/87.50 to 108.0/108.00 MHz
[Other models] ........................................... 87.50 to 108.00 MHz
• Usable Sensitivity (IHF) ...................................... 1.0 µV (11.2 dBf)
• Damping Factor (IHF)
20 Hz to 20 kHz, 8 Ω ................................................ 100 or more
• Signal to Noise Ratio (IHF)
Mono/Stereo ............................................................ 76 dB/70 dB
• Frequency Response
CD terminal to Front L/R ..................... 10 Hz to 100 kHz, –3 dB
• Harmonic Distortion (1 kHz)
Mono/Stereo .............................................................. 0.2%/0.3%
• Total Harmonic Distortion
PHONO to REC OUT (20 Hz to 20 kHz, 1 V) ................. 0.02%
CD, etc. to Front L/R (20 Hz to 20 kHz, 50 W, 8 Ω) ........ 0.06%
• Stereo Separation (1 kHz) ...................................................... 42 dB
• Signal to Noise Ratio (IHF-A Network)
Phono (5 mV) to REC OUT
[U.K., Europe, Australia and Asia models] ........................ 81 dB
[Other models] .................................................................... 86 dB
CD (250 mV) to Front L/R, Effect Off ............................. 100 dB
AM SECTION
• Residual Noise (IHF-A Network)
Front L/R .............................................................. 150 µV or less
• Usable Sensitivity ........................................................... 300 µV/m
• Channel Separation (1 kHz/10 kHz)
PHONO (shorted) to Front L/R .............................. 60 dB/55 dB
CD (5.1 kΩ terminated) to Front L/R ..................... 60 dB/45 dB
• Tone Control (Front L/R)
BASS Boost/Cut ...................................................... ±6 dB/50 Hz
BASS Turnover Frequency ............................................... 350 Hz
TREBLE Boost/Cut .............................................. ±6 dB/20 kHz
TREBLE Turnover Frequency ......................................... 3.5 kHz
• Phones Output ......................................................... 150 mV/100 Ω
• Input Sensitivity/Input Impedance
PHONO ................................................................. 2.5 mV/47 kΩ
CD, etc. ................................................................ 200 mV/47 kΩ
MULTI CH INPUT .............................................. 200 mV/47 kΩ
• Output Level/Output Impedance
REC OUT ............................................................ 200 mV/1.2 kΩ
PRE OUT ....................................................................2 V/1.2 kΩ
SUB WOOFER .......................................................... 4 V/1.7 kΩ
ZONE 2 OUTPUT
[U.S.A., Canada and Australia models] ........... 200 mV/1.2 kΩ
RX-V750
AV Receiver
• Frequency Response ........................ 20 Hz to 15 kHz, +0.5, –2 dB
• Tuning Range
[U.S.A. and Canada models] ............................ 530 to 1710 kHz
[Asia and General models] ............... 530/531 to 1710/1611 kHz
[Other models] .................................................. 531 to 1611 kHz
GENERAL
• Power Supply
[U.S.A. and Canada models] ............................ AC 120 V, 60 Hz
[Australia model] .............................................. AC 240 V, 50 Hz
[China model] ................................................... AC 220 V, 50 Hz
[Korea model] ................................................... AC 220 V, 60 Hz
[U.K. and Europe models] ................................ AC 230 V, 50 Hz
[General model] .............. AC 110/120/220/230-240 V, 50/60 Hz
[Asia model] ................................. AC 220/230-240 V, 50/60 Hz
• Power Consumption
[U.S.A. and Canada models] ............................... 400 W/500 VA
[Other models] .................................................................. 440 W
• Standby Power Consumption ............................................... 0.1 W
• AC Outlets
[U.K. and Australia models] ............. 1 (Total 100 W maximum)
[China, Asia and General models] ...... 2 (Total 50 W maximum)
[Other models] .................................. 2 (Total 100 W maximum)
• Dimension (W x H x D) ................................ 435 x 171 x 420 mm
(17-1/8” x 6-3/4” x 16-1/2”)
• Weight ............................................................ 12.5 kg (27 lbs 9 oz)
© 2004
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
All rights reserved.
OWNER’S MANUAL
Printed in Malaysia
WC85490