Raritan Dominion KX II User guide

Dominion KX II
User Guide
Release 2.3
Copyright © 2010 Raritan, Inc.
DKX2-v2.3.0-0M-E
July 2010
255-62-4023-00
This document contains proprietary information that is protected by copyright. All rights reserved. No
part of this document may be photocopied, reproduced, or translated into another language without
express prior written consent of Raritan, Inc.
© Copyright 2010 Raritan, Inc. All third-party software and hardware mentioned in this document are
registered trademarks or trademarks of and are the property of their respective holders.
FCC Information
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a commercial installation. This equipment generates, uses, and can
radiate radio frequency energy and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. Operation of this equipment in a residential
environment may cause harmful interference.
VCCI Information (Japan)
Raritan is not responsible for damage to this product resulting from accident, disaster, misuse, abuse,
non-Raritan modification of the product, or other events outside of Raritan's reasonable control or not
arising under normal operating conditions.
Contents
Chapter 1
Introduction
1
Dominion KX II Help....................................................................................................................... 1
Related Documentation ....................................................................................................... 1
What's New in the Help ....................................................................................................... 2
Dominion KX II Overview ............................................................................................................... 3
Client Applications that Can Be Used with the Dominion KX II ..................................................... 5
Virtual Media .................................................................................................................................. 6
Product Photos .............................................................................................................................. 7
Product Features ........................................................................................................................... 9
Hardware ............................................................................................................................. 9
Software............................................................................................................................. 10
Terminology ................................................................................................................................. 10
Package Contents........................................................................................................................ 12
Chapter 2 Installation and Configuration
13
Overview ...................................................................................................................................... 13
Default Login Information ............................................................................................................. 13
Getting Started ............................................................................................................................. 14
Step 1: Configure KVM Target Servers ............................................................................. 14
Step 2: Configure Network Firewall Settings ..................................................................... 25
Step 3: Connect the Equipment......................................................................................... 26
Step 4: Configure the Dominion KX II ............................................................................... 29
Valid Special Characters for Target Names ...................................................................... 32
Step 5 (Optional): Configure Keyboard Language ............................................................ 35
Chapter 3 Working with Target Servers
36
Interfaces ..................................................................................................................................... 36
Dominion KX II Local Console Interface ............................................................................ 37
Dominion KX II Remote Console Interface........................................................................ 37
Proxy Server Configuration for use with Dominion KX II, MPC, VKC and AKC .......................... 50
Multi-Platform Client Interface ..................................................................................................... 51
Launching MPC from a Web Browser ............................................................................... 51
Virtual KVM Client ........................................................................................................................ 52
Overview ............................................................................................................................ 52
Connecting to a KVM Target Server ................................................................................. 52
VKC Toolbar ...................................................................................................................... 53
Switching Between KVM Target Servers .......................................................................... 54
Power Controlling a Target Server .................................................................................... 54
Disconnecting KVM Target Servers .................................................................................. 55
Choosing USB Profiles ...................................................................................................... 56
iii
Contents
Connection Properties ....................................................................................................... 57
Connection Information ..................................................................................................... 59
Keyboard Options .............................................................................................................. 59
Video Properties ................................................................................................................ 62
Mouse Options................................................................................................................... 68
VKC Virtual Media ............................................................................................................. 73
Smart Cards (VKC, AKC and MPC) .................................................................................. 74
Tool Options ...................................................................................................................... 76
View Options...................................................................................................................... 79
Help Options ...................................................................................................................... 80
Active KVM Client (AKC) ............................................................................................................. 80
Overview ............................................................................................................................ 80
AKC Supported Operating Systems and Browsers ........................................................... 81
Prerequisites for Using AKC .............................................................................................. 82
Chapter 4 Power Strip (Rack PDU) Outlet Control
83
Overview ...................................................................................................................................... 83
Turning Outlets On/Off and Cycling Power ................................................................................. 84
Chapter 5 Virtual Media
87
Overview ...................................................................................................................................... 88
Prerequisites for Using Virtual Media .......................................................................................... 91
Using Virtual Media via VKC and AKC in a Windows Environment ............................................ 92
Using Virtual Media ...................................................................................................................... 93
File Server Setup (File Server ISO Images Only) ........................................................................ 94
Connecting to Virtual Media ......................................................................................................... 96
Local Drives ....................................................................................................................... 96
Conditions when Read/Write is Not Available ................................................................... 97
CD-ROM/DVD-ROM/ISO Images...................................................................................... 97
Disconnecting Virtual Media ........................................................................................................ 99
Chapter 6 USB Profiles
100
Overview .................................................................................................................................... 100
CIM Compatibility ....................................................................................................................... 101
Available USB Profiles ............................................................................................................... 101
Selecting Profiles for a KVM Port .............................................................................................. 107
Mouse Modes when Using the Mac OS-X USB Profile with a DCIM-VUSB ................... 107
Chapter 7 User Management
108
User Groups............................................................................................................................... 108
User Group List................................................................................................................ 109
Relationship Between Users and Groups ....................................................................... 109
Adding a New User Group............................................................................................... 109
Modifying an Existing User Group ................................................................................... 116
iv
Contents
Users .......................................................................................................................................... 117
User List........................................................................................................................... 117
Adding a New User .......................................................................................................... 118
Modifying an Existing User .............................................................................................. 118
Logging a User Off (Force Logoff) ................................................................................... 119
Authentication Settings .............................................................................................................. 120
Implementing LDAP/LDAPS Remote Authentication ...................................................... 121
Returning User Group Information from Active Directory Server .................................... 125
Implementing RADIUS Remote Authentication ............................................................... 126
Returning User Group Information via RADIUS .............................................................. 128
RADIUS Communication Exchange Specifications......................................................... 128
User Authentication Process ........................................................................................... 130
Changing a Password ................................................................................................................ 131
Chapter 8 Device Management
132
Network Settings ........................................................................................................................ 132
Network Basic Settings.................................................................................................... 133
LAN Interface Settings ..................................................................................................... 135
Device Services ......................................................................................................................... 137
Enabling SSH .................................................................................................................. 138
HTTP and HTTPS Port Settings ...................................................................................... 138
Entering the Discovery Port ............................................................................................. 138
Configuring and Enabling Tiering .................................................................................... 139
Enabling Direct Port Access ............................................................................................ 143
Enabling the AKC Download Server Certificate Validation ............................................. 144
Configuring Modem Settings ..................................................................................................... 145
Configuring Date/Time Settings ................................................................................................. 146
Event Management .................................................................................................................... 148
Configuring Event Management - Settings...................................................................... 148
Event Management - Destinations .................................................................................. 150
Power Supply Setup .................................................................................................................. 154
Configuring Ports ....................................................................................................................... 156
Configuring Standard Target Servers .............................................................................. 157
Configuring KVM Switches .............................................................................................. 158
Configuring Power Strip (Rack PDU) Targets ................................................................. 159
Configuring Blade Chassis .............................................................................................. 165
Configuring USB Profiles (Port Page) ............................................................................. 185
Configuring Dominion KX II Local Port Settings .............................................................. 188
Chapter 9 Security Management
193
Security Settings ........................................................................................................................ 193
Login Limitations .............................................................................................................. 194
Strong Passwords ........................................................................................................... 195
User Blocking................................................................................................................... 196
Encryption & Share .......................................................................................................... 197
Enabling FIPS 140-2 ....................................................................................................... 200
v
Contents
Configuring IP Access Control ................................................................................................... 202
SSL Certificates ......................................................................................................................... 205
Security Banner ......................................................................................................................... 207
Chapter 10 Maintenance
209
Audit Log .................................................................................................................................... 209
Device Information ..................................................................................................................... 210
Backup and Restore .................................................................................................................. 211
USB Profile Management .......................................................................................................... 214
Handling Conflicts in Profile Names ................................................................................ 215
Upgrading CIMs ......................................................................................................................... 215
Upgrading Firmware .................................................................................................................. 216
Upgrade History ......................................................................................................................... 219
Rebooting................................................................................................................................... 219
Stopping CC-SG Management .................................................................................................. 221
Chapter 11 Diagnostics
223
Network Interface Page ............................................................................................................. 223
Network Statistics Page ............................................................................................................. 223
Ping Host Page .......................................................................................................................... 226
Trace Route to Host Page ......................................................................................................... 226
Device Diagnostics .................................................................................................................... 228
Chapter 12 Command Line Interface (CLI)
230
Overview .................................................................................................................................... 230
Accessing the Dominion KX II Using CLI................................................................................... 231
SSH Connection to the Dominion KX II ..................................................................................... 231
SSH Access from a Windows PC .................................................................................... 231
SSH Access from a UNIX/Linux Workstation .................................................................. 232
Telnet Connection to the Dominion KX II................................................................................... 232
Enabling Telnet ................................................................................................................ 232
Access Telnet from a Windows PC ................................................................................. 232
Logging In .................................................................................................................................. 233
Navigation of the CLI ................................................................................................................. 234
Completion of Commands ............................................................................................... 234
CLI Syntax -Tips and Shortcuts ....................................................................................... 234
Common Commands for All Command Line Interface Levels ........................................ 235
Initial Configuration Using CLI ................................................................................................... 235
Setting Parameters .......................................................................................................... 235
Setting Network Parameters............................................................................................ 236
CLI Prompts ............................................................................................................................... 236
CLI Commands .......................................................................................................................... 236
Security Issues ................................................................................................................ 237
Administering the Dominion KX II Console Server Configuration Commands .......................... 237
Configuring Network .................................................................................................................. 238
Interface Command ......................................................................................................... 238
Name Command ........................................................................................................... 239
vi
Contents
IPv6 Command ................................................................................................................ 239
Chapter 13 Dominion KX II Local Console
240
Overview .................................................................................................................................... 240
Using the Dominion KX II Local Console ................................................................................... 240
Simultaneous Users ........................................................................................................ 240
Dominion KX II Local Console Interface .................................................................................... 241
Security and Authentication ....................................................................................................... 241
Local Console Smart Card Access ............................................................................................ 242
Smart Card Access in KX2 8 Devices ............................................................................. 243
Local Console USB Profile Options ........................................................................................... 243
Available Resolutions................................................................................................................. 244
Port Access Page (Local Console Server Display) ................................................................... 245
Hot Keys and Connect Keys ...................................................................................................... 247
Connect Key Examples ................................................................................................... 247
Special Sun Key Combinations ................................................................................................. 248
Accessing a Target Server ........................................................................................................ 249
Returning to the Dominion KX II Local Console Interface ......................................................... 249
Local Port Administration ........................................................................................................... 250
Configuring Dominion KX II Local Console Local Port Settings ...................................... 250
Dominion KX II Local Console Factory Reset ................................................................. 254
Resetting the Dominion KX II Using the Reset Button .............................................................. 255
Appendix A Specifications
256
Physical Specifications .............................................................................................................. 256
Environmental Requirements .................................................................................................... 258
Computer Interface Modules (CIMs).......................................................................................... 259
Supported CIMs and Operating Systems (Target Servers) ....................................................... 261
Supported Paragon CIMS and Configurations .......................................................................... 267
Dominion KX II to Dominion KX II Guidelines ................................................................. 268
Dominion KX II to Paragon II Guidelines ......................................................................... 269
Supported Operating Systems (Clients) .................................................................................... 271
Supported Browsers .................................................................................................................. 272
Certified Modems ....................................................................................................................... 272
Devices Supported by the KX2-832 and KX2-864 Extended Local Port ................................... 273
Target Server Connection Distance and Video Resolution ....................................................... 273
KX2-832 and KX2-864 Extended Local Port Recommended Maximum Distances .................. 273
Remote Connection ................................................................................................................... 274
Supported Video Resolutions .................................................................................................... 274
Supported Keyboard Languages ............................................................................................... 275
Smart Card Readers .................................................................................................................. 276
Supported and Unsupported Smart Card Readers ......................................................... 276
Minimum System Requirements...................................................................................... 278
vii
Contents
TCP and UDP Ports Used ......................................................................................................... 279
Network Speed Settings ............................................................................................................ 281
Appendix B Updating the LDAP Schema
283
Returning User Group Information............................................................................................. 283
From LDAP ...................................................................................................................... 283
From Microsoft Active Directory ...................................................................................... 283
Setting the Registry to Permit Write Operations to the Schema ............................................... 284
Creating a New Attribute ............................................................................................................ 284
Adding Attributes to the Class ................................................................................................... 285
Updating the Schema Cache ..................................................................................................... 287
Editing rciusergroup Attributes for User Members ..................................................................... 287
Appendix C Informational Notes
291
Overview .................................................................................................................................... 291
Java Runtime Environment (JRE) ............................................................................................. 291
IPv6 Support Notes .................................................................................................................... 292
Keyboards .................................................................................................................................. 293
Non-US Keyboards .......................................................................................................... 293
Macintosh Keyboard ........................................................................................................ 295
Mouse Pointer Synchronization (Fedora) .................................................................................. 296
Dell Chassis Cable Lengths and Video Resolutions ................................................................. 296
Fedora ........................................................................................................................................ 297
Resolving Fedora Core Focus ......................................................................................... 297
VKC and MPC Smart Card Connections to Fedora Servers ........................................... 297
Resolving Issues with Firefox Freezing when Using Fedora .......................................... 297
Video Modes and Resolutions ................................................................................................... 297
SUSE/VESA Video Modes .............................................................................................. 297
Supported Video Resolutions Not Displaying.................................................................. 298
USB Ports and Profiles .............................................................................................................. 298
VM-CIMs and DL360 USB Ports ..................................................................................... 298
Help for Choosing USB Profiles ...................................................................................... 298
Changing a USB Profile when Using a Smart Card Reader ........................................... 300
CIMs ........................................................................................................................................... 300
Windows 3-Button Mouse on Linux Targets.................................................................... 300
Windows 2000 Composite USB Device Behavior for Virtual Media................................ 301
Virtual Media .............................................................................................................................. 301
Virtual Media Not Refreshed After Files Added............................................................... 301
Accessing Virtual Media on a Windows 2000 Server Using a D2CIM-VUSB ................. 302
Target BIOS Boot Time with Virtual Media ...................................................................... 302
Virtual Media Connection Failures Using High Speed for Virtual Media Connections .... 302
CC-SG ....................................................................................................................................... 302
Virtual KVM Client Version Not Known from CC-SG Proxy Mode .................................. 302
Single Mouse Mode - Connecting to a Dominion KX II Target Under CC-SG Control Via
VKC Using Firefox ........................................................................................................... 302
Proxy Mode and MPC ..................................................................................................... 303
Moving Between Ports of the Dominion KX II ................................................................. 303
viii
Contents
Appendix D FAQs
304
General Questions ..................................................................................................................... 305
Remote Access .......................................................................................................................... 307
Universal Virtual Media .............................................................................................................. 309
USB Profiles............................................................................................................................... 310
Bandwidth and KVM-over-IP Performance ................................................................................ 312
Ethernet and IP Networking ....................................................................................................... 317
IPv6 Networking ......................................................................................................................... 320
Servers ....................................................................................................................................... 322
Blade Servers ............................................................................................................................ 323
Installation .................................................................................................................................. 326
Local Port ................................................................................................................................... 328
Extended Local Port (Dominion KX2-832 and KX2-864 Models Only) ..................................... 330
Power Control ............................................................................................................................ 331
Scalability ................................................................................................................................... 333
Computer Interface Modules (CIMs).......................................................................................... 335
Security ...................................................................................................................................... 336
Smart Cards and CAC Authentication ....................................................................................... 338
Manageability ............................................................................................................................. 339
Miscellaneous ............................................................................................................................ 340
Index
341
ix
Chapter 1
Introduction
In This Chapter
Dominion KX II Help ..................................................................................1
Dominion KX II Overview...........................................................................3
Client Applications that Can Be Used with the Dominion KX II .................5
Virtual Media ..............................................................................................6
Product Photos ..........................................................................................7
Product Features .......................................................................................9
Terminology .............................................................................................10
Package Contents ...................................................................................12
Dominion KX II Help
The Dominion KX II help provides information on how to install, set up,
and configure the Dominion KX II. It also includes information on
accessing target servers and power strips, using virtual media, managing
users and security, and maintaining and diagnosing the Dominion KX II.
A PDF version of the help can be downloaded from the Raritan
Firmware and Documentation page
http://www.raritan.com/support/firmware-and-documentation/ on the
Raritan website. Raritan recommends that you refer to the Raritan
website for the most up-to-date user guides available.
In order to use online help, Active Content must be enabled in your
browser. If you are using Internet Explorer 7, you must enable Scriplets.
Consult your browser help for information on enabling these features.
Related Documentation
The Dominion KX II help is accompanied by a Dominion KX II Device
Quick Setup Guide and a Dominion KX II VMWare Quick Setup Guide,
which can be found on the Raritan Firmware and Documentation page
http://www.raritan.com/support/firmware-and-documentation/ of
Raritan's website. Installation requirements and instructions for client
applications used with the Dominion KX II can be found in the KVM and
Serial Access Clients Guide, also found on the Raritan website. Where
applicable, specific client functions used with the Dominion KX II are
included in the help.
1
Chapter 1: Introduction
What's New in the Help
The following information has been added based on enhancements and
changes to the equipment and/or user documentation.

You are now able to use a tiering configuration in which a base
Dominion KX II device is used to access multiple other tiered
devices. See Configuring and Enabling Tiering (on page 139) for
more information on tiering.

You are now able to configure HTTP and/or HTTPS ports used by
the Dominion KX II. See HTTP and HTTPS Port Settings (on page
138).

A security banner feature has been added that allows you to create
and display a security banner and optionally require users to accept
or decline a security agreement during the Dominion KX II login
process. See Security Banner (on page 207).

The Dominion KX II supports the P2CIM-APS2DUAL and
P2CIM-AUSBDUAL CIMs, which provide two RJ45 connections to
different KVM switches. See Supported Paragon CIMS and
Configurations (on page 267).

A new tab has been added to the Port Access page that allows you
to search for a server by name. See Port Access Page (on page
42).

Additional prerequisite information has been added to the help
regarding using AKC. See Prerequisites for Using AKC (on page
82).

You are now able to select the active USB profile from the local
console. See Local Console USB Profile Options (on page 243).
Please see the release notes for a more detailed explanation of the
changes applied to this version of the help.
2
Chapter 1: Introduction
Dominion KX II Overview
The Dominion KX II is an enterprise-class, secure, digital KVM
(Keyboard, Video, Mouse) switch that provides BIOS-level (and up)
access and control of servers from anywhere in the world via a web
browser. Up to 64 servers can be controlled with a standard Dominion
KX II. With the Dominion KX II 8-user model, up to 32 servers can be
controlled with the KX2-832 and up to 64 servers can be controlled with
the KX2-864.
The Dominion KX II supports up to 8 video channels, allowing up to eight
concurrent users to connect to eight different video targets at any given
point in time. At the rack, the Dominion KX II provides BIOS-level control
of up to 64 servers and other IT devices from a single keyboard, monitor,
and mouse. The integrated remote access capabilities of the Dominion
KX II provide the same levels of control of your servers via a web
browser.
The Dominion KX II is easily installed using standard UTP (Cat 5/5e/6)
cabling. Its advanced features include virtual media, 128-bit encryption,
dual power supplies, remote power control, dual Ethernet, LDAP,
RADIUS, Active Directory®, Syslog integration, external modem
capabilities, and web management. The Dominion KX II 8-user model
also provides an extended local port located on the back of the device.
These features enable you to deliver higher up-time, better productivity,
and bulletproof security - at any time from anywhere.
The Dominion KX II products can operate as standalone appliances and
do not rely on a central management device. For larger data centers and
enterprises, numerous Dominion KX II devices (along with Dominion SX
devices for remote serial console access and Dominion KSX for
remote/branch office management) can be integrated into a single logical
solution using Raritan's CommandCenter Secure Gateway (CC-SG)
management unit.
3
Chapter 1: Introduction
4
Chapter 1: Introduction
Diagram key
Cat5 cable
Remote virtual media USB
drive(s)
Computer Interface
Module (CIM)
Power strip
Dominion KX II
Local access
Note: KX2-832 and
KX2-864 also use an
extended local port.
Remote KVM and serial
devices
IP LAN/WAN
Modem
PSTN
Remote (network)
access
Client Applications that Can Be Used with the Dominion KX II
The following client applications can be used in the Dominion KX II:
Product
Works with...
MPC
RRC
VKC
RSC
AKC
KX II (Generation 2)
KX II 2.2 (or later)
See the KVM and Serial Client Guide for additional information on the
client applications. Also see the Working with Target Servers (on page
36) section of this guide, which contains information on using the clients
with the Dominion KX II.
Note: MPC and VKC require the Java™ Runtime Environment (JRE™).
AKC is .NET based.
5
Chapter 1: Introduction
Virtual Media
All Dominion KX II models support virtual media. The benefits of virtual
media - mounting of remote drives/media on the target server to support
software installation and diagnostics - are now available in all of the
Dominion KX II models.
Each Dominion KX II comes equipped with virtual media to enable
remote management tasks using the widest variety of CD, DVD, USB,
internal and remote drives and images. Unlike other solutions, the
Dominion KX II supports virtual media access of hard drives and
remotely mounted images for added flexibility and productivity.
Virtual media sessions are secured using 128-bit AES or RC4
encryption.
The D2CIM-VUSB CIM and D2CIM-DVUSB (computer interface module)
support virtual media sessions to KVM target servers supporting the USB
2.0 interface. These CIMs also support Absolute Mouse
Synchronization™ as well as remote firmware update.
Note: The black connector on the DVUSB CIM is used for keyboard and
mouse. The gray connector is used for virtual media. Keep both plugs of
the CIM connected to the device. The device may not operate properly if
both plugs are not connected to the target server.
6
Chapter 1: Introduction
Product Photos
Dominion KX II
KX2-832
7
Chapter 1: Introduction
KX2-864
8
Chapter 1: Introduction
Product Features
Hardware

Integrated KVM-over-IP remote access

1U or 2U rack-mountable (brackets included)

Dual power supplies with failover; autoswitching power supply with
power failure warning

8, 16, 32, or 64 (on KX2-464) server ports

32 (KX2-832) or 64 (KX2-864) server ports

Support for tiering in which a base Dominion KX II device is used to
access multiple other tiered devices. See Configuring and
Enabling Tiering (on page 139) for more information on tiering.

Up to 8 video channels, depending on the device model, that allows
up to 8 users to connect to the Dominion KX II at once

Multiple user capacity (1/2/4/8 remote users; 1 local user)

UTP (Cat5/5e/6) server cabling

Dual Ethernet ports (10/100/1000 LAN) with failover

Field upgradable

Local User port for in-rack access

PS/2 keyboard/mouse ports. KX2-832 and KX2-864 are USB
only.

One front and three back panel USB 2.0 ports for supported USB
devices

Fully concurrent with remote user access

Local graphical user interface (GUI) for administration

Extended local port provides extended reach to in-rack access on
KX2 devices

Centralized access security

Integrated power control

LED indicators for dual power status, network activity, and remote
user status

Hardware Reset button

Serial port to connect to an external modem
9
Chapter 1: Introduction
Software

Virtual media with D2CIM-VUSB and D2CIM-DVUSB CIMs

Absolute Mouse Synchronization with D2CIM-VUSB CIM and
D2CIM-DVUSB CIMs

Plug-and-Play

Web-based access and management

Intuitive graphical user interface (GUI)

128-bit encryption of complete KVM signal, including video and
virtual media

LDAP, Active Directory®, RADIUS, or internal authentication and
authorization

DHCP or fixed IP addressing

Smart card/CAC authentication

SNMP and Syslog management

IPv4 and IPv6 support

Power control associated directly with servers to prevent mistakes

Integration with Raritan's CommandCenter Secure Gateway
(CC-SG) management unit

CC Unmanage feature to remove device from CC-SG control
Terminology
This manual uses the following terminology for the components of a
typical Dominion KX II configuration:
10
Chapter 1: Introduction
Diagram Key
TCP/IP
IPv4 and/or IPv6
KVM (Keyboard, Video, Mouse)
UTP Cable (Cat5/5e/6)
Dominion KX II
Local Access Console
Local User - an optional user console (consisting of a
keyboard, mouse, and multi-sync VGA monitor)
attached directly to the Dominion KX II to control KVM
target servers (directly at the rack, not through the
network). A USB smart card reader can also be
attached at the Local port to mount onto a target
server. An extended local port is also provided on the
DKX2-832 and DKX2-864 models.
Remote PC
Networked computers used to access and control KVM
target servers connected to the Dominion KX II. A USB
smart card reader can also be attached to the remote
PC and attached to a target server via the Dominion
KX II.
CIMS
Dongles that connect to each target server or power
strip. Available for all of the supported operating
systems.
Target Servers
KVM Target Servers - servers with video cards and
user interfaces (for example, Windows® operating
system®, Linux®, Solaris™, etc.) accessed remotely via
the Dominion KX II.
Dominion PX Power Strips
Raritan power strips accessed remotely via the
Dominion KX II.
See Supported CIMs and Operating Systems (Target Servers) (on
page 261) for a list of the supported operating systems and CIMs, and
see Supported Operating Systems (Clients) (on page 271) for a list of
the operating systems supported by the Dominion KX II remotely.
11
Chapter 1: Introduction
Package Contents
Each Dominion KX II ships as a fully-configured stand-alone product in a
standard 1U (2U for DKX2-864) 19" rackmount chassis. Each Dominion
KX II device ships with the following contents:
12
Amount
included
Item
1
Dominion KX II device
1
Dominion KX II Quick Setup Guide
1
Rackmount kit
1
AC power cords
1
Cat5 network cable
1
Cat5 network crossover cable
1
Set of 4 rubber feet (for desktop use)
1
Application note
1
Warranty card
Chapter 2
Installation and Configuration
In This Chapter
Overview ..................................................................................................13
Default Login Information ........................................................................13
Getting Started ........................................................................................14
Overview
This section provides a brief overview of the installation process. Each
step is further detailed in the remaining sections of this chapter.
To install and configure the Dominion KX II:

Step 1: Configure KVM Target Servers (on page 14)

Step 2: Configure Network Firewall Settings (on page 25)

Step 3: Connect the Equipment (on page 26)

Step 4: Configure the Dominion KX II (on page 29)

Step 5 (Optional): Configure Keyboard Language (on page 35)
Also included in this section is the default login information you will need.
Specifically, the default IP address, user name, and password. See
Default Login Information (on page 13).
Default Login Information
Default
Value
User name
The default user name is admin. This user has
administrative privileges.
Password
The default password is raritan.
Passwords are case sensitive and must be entered in the
exact case combination in which they were created. For
example, the default password raritan must be entered
entirely in lowercase letters.
The first time you start the Dominion KX II, you are
required to change the default password.
IP address
The Dominion KX II ships with the default IP address of
192.168.0.192.
Important: For backup and business continuity purposes, it is strongly
recommended that you create a backup administrator user name and
password and keep that information in a secure location.
13
Chapter 2: Installation and Configuration
Getting Started
Step 1: Configure KVM Target Servers
KVM target servers are the computers that will be accessed and
controlled via the Dominion KX II. Before installing the Dominion KX II,
configure all KVM target servers to ensure optimum performance. This
configuration applies only to KVM target servers, not to the client
workstations (remote PCs) used to access the Dominion KX II remotely.
See Terminology (on page 10) for additional information.
Desktop Background
For optimal bandwidth efficiency and video performance, KVM target
servers running graphical user interfaces such as Windows®, Linux®,
X-Windows, Solaris™, and KDE require configuration. The desktop
background need not be completely solid but desktop backgrounds
featuring photos or complex gradients might degrade performance.
Mouse Settings
The Dominion KX II operates in several mouse modes:

Absolute Mouse Mode™ (D2CIM-VUSB only)

Intelligent Mouse Mode (do not use an animated mouse)

Standard Mouse Mode
Mouse parameters do not have to be altered for Absolute Mouse
Synchronization but D2CIM-VUSB or D2CIM-DVUSB is required for this
mode. For both the Standard and Intelligent mouse modes, mouse
parameters must be set to specific values, which are described here.
Mouse configurations will vary on different target operating systems.
Consult your OS documentation for additional detail.
Intelligent mouse mode generally works well on most Windows
platforms. Intelligent mouse mode may produce unpredictable results
when active desktop is set on the target. For additional information on
Intelligent mouse mode settings, see Intelligent Mouse Mode (on page
71).
Servers with internal KVM switches inside the blade chassis typically do
not support absolute mouse technology.
14
Chapter 2: Installation and Configuration
Windows 7, Windows XP, Windows 2003 and Windows 2008 Settings
To configure KVM target servers running Microsoft® Windows
7®, Windows XP® operating system, Windows 2003® operating
system or Windows 2008® operating systems:
1. Configure the mouse settings:
a. Choose Start > Control Panel > Mouse.
b. Click the Pointer Options tab.
c.
In the Motion group:

Set the mouse motion speed setting to exactly the middle
speed.

Disable the "Enhance pointer precision" option.

Disable the Snap To option.

Click OK.
Note: When you are running Windows 2003 on your target server, if
you access the server via KVM and perform any one off the actions
listed below, mouse synchronization may be lost if it has been
previously enabled. You will need to select the Synchronize Mouse
command from the Mouse menu in the client to enable it again.
Following are the actions that may cause this to occur:
- Opening a text editor.
- Accessing the Mouse Properties, Keyboard Properties, and Phone
and Mode Options from the Windows Control Panel.
2. Disable transition effects:
a. Select the Display option from the Control Panel.
b. Click the Appearance tab.
c.
Click the Effects button.
d. Deselect the "Use the following transition effect for menus and
tooltips" option.
e. Click OK.
3. Close the Control Panel.
15
Chapter 2: Installation and Configuration
Note: For KVM target servers running Windows XP, Windows 2000 or
Windows 2008, you may wish to create a user name that will be used
only for remote connections through the Dominion KX II. This will enable
you to keep the target server's slow mouse pointer motion/acceleration
settings exclusive to the Dominion KX II connection.
Windows XP, 2000, and 2008 login pages revert to preset mouse
parameters that differ from those suggested for optimal Dominion KX II
performance. As a result, mouse synchronization may not be optimal for
these screens.
WARNING! Proceed only if you are comfortable adjusting the registry on
Windows KVM target servers. You can obtain better Dominion KX II
mouse synchronization at the login pages by using the Windows registry
editor to change the following settings: HKey_USERS\.DEFAULT\Control
Panel\Mouse: > MouseSpeed = 0;MouseThreshold
1=0;MouseThreshold 2=0.
Windows 2000 Settings
To configure KVM target servers running Microsoft® Windows
2000® operating system:
1. Configure the mouse settings:
a. Choose Start > Control Panel > Mouse.
b. Click the Motion tab.

Set the acceleration to None.

Set the mouse motion speed setting to exactly the middle
speed.

Click OK.
2. Disable transition effects:
a. Select the Display option from the Control Panel.
b. Click the Effects tab.

Deselect the "Use the following transition effect for menus
and tooltips" option.
3. Click OK and close the Control Panel.
16
Chapter 2: Installation and Configuration
Note: For KVM target servers running Windows XP, Windows 2000 or
Windows 2008, you may wish to create a user name that will be used
only for remote connections through the Dominion KX II. This will enable
you to keep the target server's slow mouse pointer motion/acceleration
settings exclusive to the Dominion KX II connection.
Windows XP, 2000, and 2008 login pages revert to preset mouse
parameters that differ from those suggested for optimal Dominion KX II
performance. As a result, mouse synchronization may not be optimal for
these screens.
WARNING! Proceed only if you are comfortable adjusting the registry on
Windows KVM target servers. You can obtain better Dominion KX II
mouse synchronization at the login pages by using the Windows registry
editor to change the following settings: HKey_USERS\.DEFAULT\Control
Panel\Mouse: > MouseSpeed = 0;MouseThreshold
1=0;MouseThreshold 2=0.
Windows Vista Settings
To configure KVM target servers running Windows Vista®
operating system:
1. Configure the mouse settings:
a. Choose Start > Settings > Control Panel > Mouse.
b. Click the Pointer Options tab.
c.
In the Motion group:

Set the mouse motion speed setting to exactly the middle
speed.

Disable the "Enhanced pointer precision" option.

Click OK.
2. Disable animation and fade effects:
a. Select the System option from the Control Panel.
b. Select Performance Information then Tools > Advanced Tools >
Adjust to adjust the appearance and performance of Windows.
c.
Click the Advanced tab.
d. Click the Settings button in the Performance group to open the
Performance Options dialog.
e. Under Custom options, deselect the following checkboxes:


Animation options:

Animate controls and elements inside windows

Animate windows when minimizing and maximizing
Fade options:
17
Chapter 2: Installation and Configuration

Fade or slide menus into view

Fade or slide ToolTips into view

Fade out menu items after clicking
3. Click OK and Close the Control Panel.
Linux Settings (Red Hat 9)
Note: The following settings are optimized for Standard Mouse mode
only.
To configure KVM target servers running Linux® (graphical user
interface):
1. Configure the mouse settings:
a. Choose Main Menu > Preferences > Mouse. The Mouse
Preferences dialog appears.
b. Click the Motion tab.
c.
Within the Speed group, set the Acceleration slider to the exact
center.
d. Within the Speed group, set the Sensitivity towards low.
e. Within the Drag & Drop group, set the Threshold towards small.
f.
Close the Mouse Preferences dialog.
Note: If these steps do not work, issue the xset mouse 1 1 command
as described in the Linux command line instructions.
2. Configure the screen resolution:
a. Choose Main Menu > System Settings > Display. The Display
Settings dialog appears.
b. From the Display tab, select a Resolution supported by the
Dominion KX II.
c.
From the Advanced tab, verify that the Refresh Rate is
supported by the Dominion KX II.
Note: Once connected to the target server, in many Linux graphical
environments, the <Ctrl> <Alt> <+> command will change the video
resolution, scrolling through all available resolutions that remain enabled
in the XF86Config or /etc/X11/xorg.conf, depending on your X server
distribution.
To configure KVM target servers running Linux (command line):
1. Set the mouse acceleration to exactly 1 and set the threshold to
exactly 1. Enter this command: xset mouse 1 1. This should be set
for execution upon login.
18
Chapter 2: Installation and Configuration
2. Ensure that each target server running Linux is using a resolution
supported by the Dominion KX II at a standard VESA resolution and
refresh rate.
3. Each Linux target server should also be set so the blanking times are
within +/- 40% of VESA standard values:
a. Go to the Xfree86 Configuration file XF86Config.
b. Using a text editor, disable all non-Dominion KX II supported
resolutions.
c.
Disable the virtual desktop feature (not supported by the
Dominion KX II).
d. Check blanking times (+/- 40% of VESA standard).
e. Restart computer.
Note: If you change the video resolution, you must log off of the target
server and log back in for the video settings to take effect.
Note for Red Hat 9 KVM Target Servers
If you are running Red Hat® 9 on the target server using a USB CIM, and
are experiencing problems with the keyboard and/or mouse, there is an
additional configuration setting you can try.
Tip: You might have to perform these steps even after a fresh OS
installation.
To configure Red Hat 9 servers using USB CIMs:
1. Locate the configuration file (usually /etc/modules.conf) in your
system.
2. Using the editor of your choice, make sure that the alias
usb-controller line in the modules.conf file is as follows:
alias usb-controller usb-uhci
Note: If there is another line using usb-uhci in the /etc/modules.conf
file, it needs to be removed or commented out.
3. Save the file.
4. Reboot the system in order for the changes to take effect.
Linux Settings (Red Hat 4)
Note: The following settings are optimized for Standard Mouse mode
only.
To configure KVM target servers running Linux® (graphical user
interface):
1. Configure the mouse settings:
19
Chapter 2: Installation and Configuration
a. Choose Main Menu > Preferences > Mouse. The Mouse
Preferences dialog appears.
b. Open the Motion tab.
c.
Within the Speed group, set the Acceleration slider to the exact
center.
d. Within the Speed group, set the Sensitivity towards low.
e. Within the Drag & Drop group, set the Threshold towards small.
f.
Close the Mouse Preferences dialog.
Note: If these steps do not work, issue the xset mouse 1 1 command
as described in the Linux command line instructions.
2. Configure the screen resolution:
a. Choose Main Menu > System Settings > Display. The Display
Settings dialog appears.
b. On the Settings tab, select a Resolution supported by the
Dominion KX II.
c.
Click OK.
Note: Once connected to the target server, in many Linux graphical
environments, the <Ctrl> <Alt> <+> command will change the video
resolution, scrolling through all available resolutions that remain enabled
in the XF86Config or /etc/X11/xorg.conf, depending on your X server
distribution
Note: If you change the video resolution, you must log out of the target
server and log back in for the video settings to take effect.
SUSE Linux 10.1 Settings
Note: Do not attempt to synchronize the mouse at the SUSE Linux® login
prompt. You must be connected to the target server to synchronize the
mouse cursors.
To configure the mouse settings:
1. Choose Desktop > Control Center. The Desktop Preferences dialog
appears.
2. Click Mouse. The Mouse Preferences dialog appears.
3. Open the Motion tab.
4. Within the Speed group, set the Acceleration slider to the exact
center position.
5. Within the Speed group, set the Sensitivity slider to low.
6. Within the Drag & Drop group, set the Threshold slider to small.
20
Chapter 2: Installation and Configuration
7. Click Close.
To configure the video:
1. Choose Desktop Preferences > Graphics Card and Monitor. The
Card and Monitor Properties dialog appears.
2. Verify that a Resolution and Refresh Rate is in use that is supported
by the Dominion KX II. See Supported Video Resolutions (on page
274) for more information.
Note: If you change the video resolution, you must log out of the
target server and log back in for the video settings to take effect.
Make Linux Settings Permanent
Note: These steps may vary slightly depending on the specific version of
Linux® in use.
To make your settings permanent in Linux (prompt):
1. Choose System Menu > Preferences > Personal > Sessions.
2. Click the Session Options tab.
3. Select the "Prompt on log off" checkbox and click OK. This option
prompts you to save your current session when you log out.
4. Upon logging out, select the "Save current setup" option from the
dialog.
5. Click OK.
Tip: If you do not want to be prompted upon log out, follow these
procedures instead.
To make your settings permanent in Linux (no prompt):
1. Choose Desktop > Control Center > System > Sessions.
2. Click the Session Options tab.
3. Deselect the "Prompt on the log off" checkbox.
4. Select the "Automatically save changes to the session" checkbox
and click OK. This option automatically saves your current session
when you log out.
Sun Solaris Settings
To configure KVM target servers running Sun™ Solaris™:
1. Set the mouse acceleration value to exactly 1 and the threshold to
exactly 1. This can be performed from:
21
Chapter 2: Installation and Configuration

The graphical user interface.

The command line xset mouse a t where a is the acceleration
and t is the threshold.
2. All KVM target servers must be configured to one of the display
resolutions supported by the Dominion KX II. The most popular
supported resolutions for Sun machines are:
Display resolution
Vertical refresh rate
Aspect ratio
1600 x 1200
60 Hz
4:3
1280 x 1024
60,75,85 Hz
5:4
1152 x 864
75 Hz
4:3
1024 x 768
60,70,75,85 Hz
4:3
800 x 600
56,60,72,75,85 Hz
4:3
720 x 400
85 Hz
9:5
640 x 480
60,72,75,85 Hz
4:3
3. KVM target servers running the Solaris operating system must output
VGA video (H-and-V sync, not composite sync).
To change your Sun video card output from composite sync to
the nondefault VGA output:
1. Issue the Stop+A command to drop to bootprom mode.
2. Issue the following command to change the output resolution: setenv
output-device screen:r1024x768x70
3. Issue the boot command to reboot the server.
You can also contact your Raritan representative to purchase a video
output adapter:
22
If you have:
Use this video output adapter:
Sun 13W3 with composite
sync output
APSSUN II Guardian converter
Chapter 2: Installation and Configuration
If you have:
Use this video output adapter:
Sun HD15 with composite
sync output
1396C converter to convert from
HD15 to 13W3 and an APSSUN II
Guardian converter to support
composite sync
Sun HD15 with separate sync
output
APKMSUN Guardian converter
Note: Some of the standard Sun background screens may not center
precisely on certain Sun servers with dark borders. Use another
background or place a light colored icon in the upper left hand corner.
Mouse Settings
To configure the mouse settings (Sun Solaris 10.1):
1. Choose Launcher. Application Manager - Desktop Controls opens.
2. Choose Mouse Style Manager. The Style Manager - Mouse dialog
appears.
3. Set the Acceleration slider to 1.0.
4. Set the Threshold slider to 1.0.
5. Click OK.
Accessing the Command Line
1. Right click.
2. Choose Tools > Terminal. A terminal window opens. (It is best to be
at the root to issue commands.)
Video Settings (POST)
Sun systems have two different resolution settings: a POST resolution
and a GUI resolution. Run these commands from the command line.
Note: 1024x768x75 is used as an example here; substitute the resolution
and refresh rate you are using.
To check current POST resolution:

Run the following command as the root: # eeprom output-device
To change POST resolution:
1. Run # eeprom output-device=screen:r1024x768x75.
2. Log out or restart computer.
23
Chapter 2: Installation and Configuration
Video Settings (GUI)
The GUI resolution can be checked and set using different commands
depending on the video card in use. Run these commands from the
command line.
Note: 1024x768x75 is used as an example here; substitute the resolution
and refresh rate you are using.
Card
To check resolution:
To change resolution:
32-bit
# /usr/sbin/pgxconfig -prconf
1. # /usr/sbin/pgxconfig -res
1024x768x75
2. Log out or restart computer.
64-bit
# /usr/sbin/m64config -prconf
1. # /usr/sbin/m64config -res
1024x768x75
2. Log out or restart computer.
32-bit
and
64-bit
# /usr/sbin/fbconfig -prconf
1. # /usr/sbin/fbconfig -res
1024x768x75
2. Log out or restart computer.
IBM AIX 5.3 Settings
Follow these steps to configure KVM target servers running IBM® AIX™
5.3.
To configure the mouse:
1. Go to Launcher.
2. Choose Style Manager.
3. Click Mouse. The Style Manager - Mouse dialog appears.
4. Use the sliders to set the Mouse acceleration to 1.0 and Threshold to
1.0.
5. Click OK.
To configure the video:
1. From the Launcher, select Application Manager.
2. Select System_Admin.
3. Choose Smit > Devices > Graphic Displays > Select the Display
Resolution and Refresh Rate.
4. Select the video card in use.
5. Click List. A list of display modes is presented.
24
Chapter 2: Installation and Configuration
6. Select a resolution and refresh rate supported by the Dominion KX II.
See Supported Video Resolutions (on page 274) for more
information.
Note: If you change the video resolution, you must log out of the target
server and log back in for the video settings to take effect.
Make UNIX Settings Permanent
Note: These steps may vary slightly depending on the type of UNIX® (for
example, Solaris™, IBM® AIX™) and the specific version in use.
1. Choose Style Manager > Startup. The Style Manager - Startup
dialog appears.
2. On the Logout Confirmation dialog, select the On option. This option
prompts you to save your current session when you log out.
Apple Macintosh Settings
For KVM target servers running an Apple Macintosh® operating system,
the preferred method is to use the D2CIM-VUSB and Absolute Mouse
Synchronization.
Note: 'USB Profile 'Mac OS-X, version 10.4.9 and later' must be select
from the USB Profile menu or the Port Configuration page.
Step 2: Configure Network Firewall Settings
To access Dominion KX II through a network firewall via Multi-Platform
Client or through the Port Access page, your firewall must allow
communication on TCP Port 5000 or another port that you designate.
To take advantage of the
Dominion KX II:
The firewall must allow
inbound communication on:
Web-access capabilities
Port 443 - standard TCP port for
HTTPS communication
Automatic redirection of HTTP
requests to HTTPS
(so the more common
“http://xxx.xxx.xxx.xxx” can be
used instead of
“https://xxx.xxx.xxx.xxx”)
Port 80 - standard TCP port for
HTTP communication
See Network Settings (on page 132) for additional information about
designating another discovery port.
25
Chapter 2: Installation and Configuration
Step 3: Connect the Equipment
Connect the Dominion KX II to the power supply, network, local PC, and
target servers. The letters in the diagram correspond to the topics in this
section that describe the connection.
A. AC Power
To connect the power supply:
1. Attach the included AC power cord to the Dominion KX II and plug
into an AC power outlet.
2. For dual power failover protection, attach the second included AC
power cord and plug it into a different power source than the first
power cord.
26
Chapter 2: Installation and Configuration
Note: If you only attach one power cord, the power LED on the Dominion
KX II front panel will be red because the system is set to automatically
detect both sources. See Power Supply Setup (on page 154) for
information about turning off automatic detection for the power source
that is not in use.
B. Modem Port (Optional)
The Dominion KX II features a dedicated modem port for remote access
even when the LAN/WAN is unavailable. Using a straight-through serial
(RS-232) cable, connect an external serial modem to the port labeled
MODEM on the back of the Dominion KX II (see Specifications (on
page 256) for a list of certified modems and Configuring Modem
Settings (on page 145) for information on configuring the modem).
Note: Raritan recommends configuring the modem by enabling the CD
(carrier detect) setting.
C. Network Port
The Dominion KX II provides two Ethernet ports for failover purposes
(not for load-balancing). By default, only LAN1 is active and the
automatic failover is disabled. When enabled, if the Dominion KX II
internal network interface or the network switch to which it is connected
becomes unavailable, LAN2 will be enabled using the same IP address.
Note: Because a failover port is not activated until after a failover has
actually occurred, Raritan recommends that you either not monitor the
failover port or monitor it only after a failover occurs.
To connect the network:
1. Connect a standard Ethernet cable (included) from the network port
labeled LAN1 to an Ethernet switch, hub, or router.
2. To make use of the optional Dominion KX II Ethernet failover
capabilities:

Connect a standard Ethernet cable from the network port labeled
LAN2 to an Ethernet switch, hub, or router.

Enable Automatic Failover on the Network Configuration page.
Note: Use both network ports only if you want to use one as a failover
port.
27
Chapter 2: Installation and Configuration
D. Local Access Port (Local PC)
For convenient access to target servers while at the rack, use the
Dominion KX II Local Access port. While the Local Access port is
required for installation and setup, it is optional for subsequent use. The
Local Access port also provides a graphical user interface from the
Dominion KX II Local Console for administration and target server
access.
The KX2-832 and KX2-864 also provide you with an Extended Local
port, labeled EXT LOCAL on the back of the device, for access to target
servers while at the rack. The Extended Local port is not required for the
initial installation and setup. It is configured from the Local Console and
Remote Console. See Configuring Dominion KX II Local Port
Settings (on page 188) for additional information.
To connect the local port:

28
Attach a multi-sync VGA monitor, mouse, and keyboard to the
respective Local User ports using either a PS/2 or USB keyboard
and mouse (DKX2-832 and DKX2-864 provide USB only). The
physical connections for the Local User and Extended Local ports
can be found on the back panel of the Dominion KX II.
Connection
Description
Monitor
Attach a standard multi-sync VGA
monitor to the HD15 (female) video
port.
Keyboard
Attach either a standard PS/2
keyboard to the Mini-DIN6 (female)
keyboard port, or a standard USB
keyboard to one of the USB Type A
(female) ports.
Mouse
Attach either a standard PS/2 mouse
to the Mini-DIN6 (female) mouse port
or a standard USB mouse to one of
the USB Type A (female) ports.
Chapter 2: Installation and Configuration
E. Target Server Ports
The Dominion KX II uses standard UTP cabling (Cat5/5e/6) to connect to
each target server.
To connect a target server to the Dominion KX II:
1. Use the appropriate Computer Interface Module (CIM). See
Supported CIMs and Operating Systems (Target Servers) (on
page 261) for more information about the CIMs to use with each
operating system.
2. Attach the HD15 video connector of your CIM to the video port of
your target server. Ensure that your target server's video has already
been configured to a supported resolution and refresh rate. For Sun
servers, also ensure that your target server's video card has been
set to output standard VGA (H-and-V sync) and not composite sync.
3. Attach the keyboard/mouse connector of your CIM to the
corresponding ports on your target server. Using a standard
straight-through UTP (Cat5/5e/6) cable, connect the CIM to an
available server port on the back of your Dominion KX II device.
Note: The DCIM-USB G2 provides a small slide switch on the back of the
CIM. Move the switch to P for PC-based USB target servers. Move the
switch to S for Sun USB target servers.
A new switch position takes effect only after the CIM is power-cycled. To
power-cycle the CIM, remove the USB connector from the target server
and plug it back in a few seconds later.
Step 4: Configure the Dominion KX II
The first time you power up the Dominion KX II device, there is some
initial configuration that you need to perform through the Dominion KX II
Local Console:

Change the default password.

Assign the IP address.

Name the KVM target servers.
Changing the Default Password
The Dominion KX II ships with a default password. The first time you
start the Dominion KX II you are required to change that password.
To change the default password:
1. Power on the Dominion KX II using the power switch(s) at the back
of the unit. Wait for the Dominion KX II unit to boot. (A beep signals
that the boot is complete.)
29
Chapter 2: Installation and Configuration
2. Once the unit has booted, the Dominion KX II Local Console is
visible on the monitor attached to the Dominion KX II local port. Type
the default username (admin) and password (raritan) and click Login.
The Change Password screen is displayed.
3. Type your old password (raritan) in the Old Password field.
4. Type a new password in the New Password field and retype the new
password in the Confirm New Password field. Passwords can be up
to 64 characters in length and can consist of English, alphanumeric
characters as well as special characters.
5. Click Apply.
6. You will receive confirmation that the password was successfully
changed. Click OK. The Port Access page is displayed.
Note: The default password can also be changed from the Raritan
Multi-Platform Client (MPC).
Assigning an IP Address
These procedures describe how to assign an IP address on the Network
Settings page. For complete information about all of the fields and the
operation of this page, see Network Settings (on page 132).
1. Choose Device Settings > Network. The Network Settings page
opens.
2. Specify a meaningful Device Name for your Dominion KX II device.
Up to 32 alphanumeric characters using valid special characters and
no spaces.
3. In the IPv4 section, enter or select the appropriate IPv4-specific
network settings:
a. Enter the IP Address if needed. The default IP address is
192.168.0.192.
b. Enter the Subnet Mask. The default subnet mask is
255.255.255.0.
c.
Enter the Default Gateway if None is selected from the IP Auto
Configuration drop-down.
d. Enter the Preferred DHCP Host Name if DHCP is selected from
the IP Auto Configuration drop-down.
e. Select the IP Auto Configuration. The following options are
available:

None (Static IP) - This option requires that you manually specify
the network parameters.
This is the recommended option because the Dominion KX II is
an infrastructure device and its IP address should not change.
30
Chapter 2: Installation and Configuration

DHCP - Dynamic Host Configuration Protocol is used by
networked computers (clients) to obtain unique IP addresses
and other parameters from a DHCP server.
With this option, network parameters are assigned by the DHCP
server. If DHCP is used, enter the Preferred host name (DHCP
only). Up to 63 characters.
4. If IPv6 is to be used, enter or select the appropriate IPv6-specific
network settings in the IPv6 section:
a. Select the IPv6 checkbox to active the fields in the section.
b. Enter a Global/Unique IP Address. This is the IP address
assigned to the Dominion KX II.
c.
Enter the Prefix Length. This is the number of bits used in the
IPv6 address.
d. Enter the Gateway IP Address.
e. Link-Local IP Address. This address is automatically assigned to
the device. It is used for neighbor discovery or when no routers
are present. Read-Only
f.
Zone ID. This identifies the device with which the address is
associated. Read-Only
g. Select the IP Auto Configuration. The following options are
available:

None - Use this option if you do not want an auto IP configuration
and prefer to set the IP address yourself (static IP). This is the
default and recommended option.
If None is selected for the IP auto configuration, the following
Network Basic Settings fields are enabled: Global/Unique IP
Address, Prefix Length, and Gateway IP Address allowing you to
manually set the IP configuration.

Router Discovery - Use this option to automatically assign IPv6
addresses that have Global or Unique Local significance beyond
that of the Link Local, which only applies to a directly connected
subnet.
5. Select Obtain DNS Server Address Automatically if DHCP is
selected and Obtain DNS Server Address is enabled. When Obtain
DNS Server Address Automatically, the DNS information provided by
the DHCP server will be used.
6. If Use the Following DNS Server Addresses is selected, regardless
of whether DHCP is selected or not, the addresses entered in this
section will be used to connect to the DNS server.
Enter the following information if the Following DNS Server
Addresses option is selected. These addresses are the primary and
secondary DNS addresses that will be used if the primary DNS
server connection is lost due to an outage.
31
Chapter 2: Installation and Configuration
a. Primary DNS Server IP Address
b. Secondary DNS Server IP Address
7. When finished, click OK. Your Dominion KX II device is now network
accessible.
See LAN Interface Settings (on page 135) for information in configuring
this section of the Network Settings page.
Note: In some environments, the default LAN Interface Speed & Duplex
setting Autodetect (autonegotiator) does not properly set the network
parameters, which results in network issues. In these instances, setting
the Dominion KX II LAN Interface Speed & Duplex field to 100 Mbps/Full
Duplex (or whatever option is appropriate to your network) addresses the
issue. See the Network Settings (on page 132) page for more
information.
Naming Target Servers
To name the target servers:
1. Connect all of the target servers if you have not already done so.
See Step 3: Connect the Equipment (on page 26) for a description
of connecting the equipment.
2. Using the Dominion KX II Local Console, choose Device Settings >
Port Configuration. The Port Configuration page opens.
3. Click the Port Name of the target server you want to rename. The
Port Page opens.
4. Assign a name to identify the server connected to that port. The
name can be up to 32 characters, and alphanumeric and special
characters are allowed.
5. Click OK.
Valid Special Characters for Target Names
32
Character
Description
Character
Description
!
Exclamation point ;
Semi-colon
"
Double quote
=
Equal sign
#
Pound sign
>
Greater than sign
$
Dollar sign
?
Question mark
%
Percent sign
@
At sign
&
Ampersand
[
Left bracket
(
Left parenthesis
\
Backward slash
Chapter 2: Installation and Configuration
Character
Description
)
Right parenthesis ]
Character
Description
Right bracket
*
Asterisk
^
Caret
+
Plus sign
_
Underscore
,
Comma
`
Grave accent
-
Dash
{
Left brace
.
Period
|
Pipe sign
/
Forward slash
}
Right brace
<
Less than sign
~
Tilde
:
Colon
Specifying Power Supply Autodetection
The Dominion KX II provides dual power supplies and can automatically
detect and provide notification regarding the status of these power
supplies. Proper configuration ensures that the Dominion KX II sends the
appropriate notifications should a power supply fail.
The Power Supply Setup page is configured to automatically detect both
power supplies when two power supplies are used. If only one power
supply is used in your configuration, you can disable automatic detection
from the Power Supply Setup page.
To enable automatic detection for the power supplies in use:
1. Choose Device Settings > Power Supply Setup. The Power Supply
Setup page opens.
2. If you are plugging power input into power supply number one
(left-most power supply at the back of the device), select the
Powerln1 Auto Detect option.
3. If you are plugging power input into power supply number two
(right-most power supply at the back of the device), select the
Powerln2 Auto Detect option.
4. Click OK.
Note: If either of these checkboxes is selected and power input is not
actually connected, the power LED at the front of the device turns red.
To disable power supply autodetection for the power supply not
in use:
1. Using the Dominion KX II Local Console, choose Device Settings >
Power Supply Setup. The Power Supply Setup page opens.
33
Chapter 2: Installation and Configuration
2. Clear autodetection for the power supply that you are not using.
For more information, see Power Supply Setup (on page 154).
Note to CC-SG Users
If you are using the Dominion KX II in a CC-SG configuration, perform
the installation steps, and when finished, consult the CommandCenter
Secure Gateway User Guide, Administrator Guide, or Deployment
Guide to proceed (all found on Raritan's website, www.raritan.com,
under Support).
Note: The remainder of this help applies primarily to deploying the
Dominion KX II device(s) without the integration functionality of CC-SG.
Remote Authentication
Note to CC-SG Users
When the Dominion KX II is controlled by CommandCenter Secure
Gateway, CC-SG authenticates users and groups, except for local users
requiring Local port access. When CC-SG is controlling the Dominion KX
II, Local port users will be authenticated against the local user database
or the remote authentication server (LDAP/LDAPS or RADIUS)
configured on the Dominion KX II. They will not be authenticated against
the CC-SG user database.
For additional information about CC-SG authentication, see the
CommandCenter Secure Gateway User Guide, Administrator Guide, or
Deployment Guide, which can be downloaded from the Support section
of the Raritan website http://www.raritan.com.
Supported Protocols
To simplify management of usernames and passwords, the Dominion KX
II provides the ability to forward authentication requests to an external
authentication server. Two external authentication protocols are
supported: LDAP/LDAPS and RADIUS.
Note on Microsoft Active Directory
Microsoft® Active Directory® uses the LDAP/LDAPS protocol natively, and
can function as an LDAP/LDAPS server and authentication source for
the Dominion KX II. If it has the IAS (Internet Authorization Server)
component, a Microsoft Active Directory server can also serve as a
RADIUS authentication source.
34
Chapter 2: Installation and Configuration
Create User Groups and Users
As part of the initial configuration, you must define user groups and users
in order for users to access the Dominion KX II.
The Dominion KX II uses system-supplied default user groups and
allows you to create groups and specify the appropriate permissions to
suit your needs.
User names and passwords are required to gain access to the Dominion
KX II. This information is used to authenticate users attempting to access
your Dominion KX II.
See User Management for details on adding and editing user groups and
users.
Step 5 (Optional): Configure Keyboard Language
Note: This step is not required if you are using the US/International
language keyboard.
If you are using a non-US language, the keyboard has to be configured
for the appropriate language. In addition, the keyboard language for the
client machine and the KVM target servers has to match.
Consult the documentation for your operating system for additional
information about changing the keyboard layout.
Changing the Keyboard Layout Code (Sun Targets)
Use this procedure if you are using a DCIM-SUSB and would like the
keyboard layout changed to another language.
To change the keyboard layout code (DCIM-SUSB only):
1. Open a Text Editor window on the Sun™ workstation.
2. Check that the Num Lock key is active and press the left Ctrl key and
the Del key on your keyboard. The Caps Lock light starts to blink,
indicating that the CIM is in Layout Code Change mode. The text
window displays: Raritan Computer, Inc. Current keyboard
layout code = 22h (US5 UNIX).
3. Type the layout code desired (for example, 31 for the Japanese
keyboard).
4. Press Enter.
5. Shut down the device and power on once again. The DCIM-SUSB
performs a reset (power cycle).
6. Verify that the characters are correct.
35
Chapter 3
Working with Target Servers
In This Chapter
Interfaces .................................................................................................36
Proxy Server Configuration for use with Dominion KX II, MPC, VKC and
AKC .........................................................................................................50
Multi-Platform Client Interface .................................................................51
Virtual KVM Client ...................................................................................52
Active KVM Client (AKC) .........................................................................80
Interfaces
There are several user interfaces in the Dominion KX II, providing you
with easy access any time, anywhere. These include the Dominion KX II
Local Console, the Dominion KX II Remote Console, and the
Multi-Platform Client (MPC). The following table identifies these
interfaces and their use for target server access and administration
locally and remotely:
User Interface
Local
Access
Remote
Admin
Access
Admin
Dominion KX II Local
Console
Dominion KX II Remote
Console
Virtual KVM Client
Multi-Platform Client
(MPC)
Active KVM Client (AKC)
The following sections of the help contain information about using
specific interfaces to access the Dominion KX II and manage targets:

Local Console

Remote Console

Virtual KVM Client

Multi-Platform Client
36
Chapter 3: Working with Target Servers
Dominion KX II Local Console Interface
When you are located at the server rack, the Dominion KX II provides
standard KVM management and administration via the Dominion KX II
Local Console. The Dominion KX II Local Console provides a direct KVM
(analog) connection to your connected servers; the performance is
exactly as if you were directly connected to the server's keyboard,
mouse, and video ports.
There are many similarities among the Dominion KX II Local Console
and the Dominion KX II Remote Console graphical user interfaces.
Where there are differences, they are noted in the help.
The Dominion KX II Local Console Factory Reset option is available in
the Dominion KX II Local Console but not the Dominion KX II Remote
Console.
Dominion KX II Remote Console Interface
The Dominion KX II Remote Console is a browser-based graphical user
interface that allows you to log in to KVM target servers and serial
targets connected to the Dominion KX II and to remotely administer the
Dominion KX II.
The Dominion KX II Remote Console provides a digital connection to
your connected KVM target servers. When you log into a KVM target
server using the Dominion KX II Remote Console, a Virtual KVM Client
window opens.
There are many similarities among the Dominion KX II Local Console
and the Dominion KX II Remote Console graphical user interfaces, and
where there are differences, they are noted in the user manual. The
following options are available in the Dominion KX II Remote Console
but not the Dominion KX II Local Console:

Virtual Media

Favorites

Backup/Restore

Firmware Upgrade

Upgrade Report

Diagnostics

USB Profile Selection

USB Profile Management

SSL Certificates
Launching the Dominion KX II Remote Console
Important: Regardless of the browser used, you must allow
pop-ups from the Dominion device's IP address to launch the
37
Chapter 3: Working with Target Servers
Dominion KX II Remote Console.
Depending on your browser and security settings, you may see various
security and certificate warnings. It is necessary to accept these
warnings to launch the Dominion KX II Remote Console.
You can reduce the number of warning messages during subsequent log
ins by checking the following options on the security and certificate
warning messages:

In the future, do not show this warning.

Always trust content from this publisher.
To launch the Dominion KX II Remote Console:
1. Log in to any workstation with network connectivity to your Dominion
KX II and Java Runtime Environment installed (JRE is available on
the Java website http://java.sun.com/).
2. Launch a supported web browser such as Internet Explorer (IE) or
Firefox.
3. Type the following URL: http://IP-ADDRESS, where IP-ADDRESS is
the IP address assigned to your Dominion KX II. You can also use
https, the DNS name of the Dominion KX II assigned by the
administrator (provided that a DNS server has been configured), or
just simply type the IP address in the browser (Dominion KX II
always redirects the IP address from HTTP to HTTPS.) The Login
page opens.
4. Type your user name and password. If this is the first time logging in,
log in with the factory default user name (admin) and password
(raritan, all lower case). You will be prompted to change the default
password. See Changing the Default Password (on page 29) for
more information. Click Login.
Note: If your administrator requires you read and/or accept a security
agreement in order to access the device, a security banner will be
displayed after you have entered your login credentials and clicked
Login.
See Virtual KVM Client (on page 52) for information on the Dominion
KX II functions available via the Remote Console.
38
Chapter 3: Working with Target Servers
Interface and Navigation
Dominion KX II Console Layout
Both the Dominion KX II Remote Console and the Dominion KX II Local
Console interfaces provide an HTML (web-based) interface for
configuration and administration, as well as target server list and
selection. The options are organized into various tabs.
After successful login, the Port Access page opens listing all ports along
with their status and availability. Two tabs are provided on the page
allowing you to view by port or view by group. You can sort by Port
Number, Port Name, Status (Up and Down), and Availability (Idle,
Connected, Busy, Unavailable, and Connecting) by clicking on the
column heading. See Port Access Page (on page 42) for more
information.
39
Chapter 3: Working with Target Servers
Left Panel
The left panel of the Dominion KX II interface contains the following
information. Note that some information is conditional and will only be
displayed if you are a certain of user, are using certain features, and so
on. This conditional information is noted here.
40
Information
Description
When displayed?
Time & Session
The date and time the
current session started.
Always
User
Username
Always
State
The current state of the
application, either idle or
active. If idle, the
application tracks and
displays the time the
session has been idle.
Always
Your IP
The IP address used to
access the Dominion KX
II.
Always
Last Login
The last login date and
time.
Always
Under CC-SG
Management
The IP address of the
CC-SG device managing
the Dominion KX II.
When the Dominion KX
II is being managed by
CC-SG.
Device Information
Information specific to the Always
Dominion KX II you are
using.
Device Name
Name assigned to the
device.
Always
IP Address
The IP address of the
Dominion KX II.
Always
Firmware
Current version of
firmware.
Always
Device Model
Model of the Dominion
KX II
Always
Network
The name assigned to
the current network.
Always
PowerIn1
Status of the power 1
outlet connection. Either
on or off.
When connected.
Chapter 3: Working with Target Servers
Information
Description
When displayed?
PowerIn2
Status of the power 2
outlet connection. Either
on or off.
When connected.
Configured As
If you are using a tiering When the Dominion KX
Base or Configured configuration, this
II is part of a tiered
As Tiered
indicates if the Dominion configuration.
KX II you are accessing is
the base device or a
tiered device.
Port States
The statuses of the ports
being used by the
Dominion KX II.
Always
Connect Users
The users, identified by
Always
their username and IP
address, who are
currently connected to the
Dominion KX II.
Help - User Guide
Links to online help.
Favorite Devices
See Managing Favorites Always
(on page 45).
FIPS Mode
FIPS Mode: EnabledSSL
Certificate: FIPS Mode
Compliant
Always
When FIPS is enabled.
Dominion KX II Console Navigation
The Dominion KX II Console interfaces provide many methods for
navigation and making your selections.
To select an option (use any of the following):

Click on a tab. A page of available options appears.

Hover over a tab and select the appropriate option from the menu.

Click the option directly from the menu hierarchy displayed
(breadcrumbs).
To scroll through pages longer than the screen:

Use Page Up and Page Down keys on your keyboard.

Use the scroll bar on the right.
41
Chapter 3: Working with Target Servers
Port Access Page
After successfully logging on to the Dominion KX II Remote Console, the
Port Access page appears. This page lists all of the Dominion KX II
ports, the connected KVM target servers, and their status and
availability. The Port Access page provides access to the KVM target
servers connected to the Dominion KX II. KVM target servers are servers
that you want to control through the Dominion KX II device. They are
connected to the Dominion KX II ports at the back of the device.
Note: For each connection to a KVM target server, a new Virtual KVM
Client page is opened.
If you are using a tiered configuration in which a base Dominion KX II
device is used to access multiple other tiered devices, the tiered devices
are viewed on the Port Access page by clicking on the Expand Arrow
icon
to the left of the base device name. See Configuring and
Enabling Tiering (on page 139) for more information on tiering.
Also displayed on the Port Access page are blade chassis that have
been configured in the Dominion KX II. The blade chassis is displayed in
an expandable, hierarchical list on the Port Access page, with the blade
chassis at the root of the hierarchy and the individual blades labeled and
displayed below the root. Use the Expand Arrow icon next to the root
chassis to display the individual blades.
Note: To view the blade chassis in a hierarchal order, blade-chassis
subtypes must be configured for the blade server chassis.
By default, the View by Port tab will be displayed on the Port Access
page. The View by Group tab displays port groups and can be
expandable to display ports that are assigned to the port group. The
View by Search tab allows you to search by port name. The search
feature supports the use of an asterisk (*) as a wildcard, and full and
partial names.
To use the Port Access page:
1. From the Dominion KX II Remote Console, click the Port Access tab.
The Port Access page opens.
The KVM target servers are initially sorted by Port Number. You can
change the display to sort on any of the columns.
42

Port Number - Numbered from 1 to the total number of ports
available for the Dominion KX II device. Note that ports
connected to power strips will not be among those listed,
resulting in gaps in the Port Number sequence.

Port Name - The name of the Dominion KX II port. Initially, this is
set to Dominion-KX2-Port# but you can change the name to
something more descriptive. When you click a Port Name link,
the Port Action Menu appears.
Chapter 3: Working with Target Servers
Note: Do not use apostrophes for the Port (CIM) Name.

Status - The status for standard servers is either up or down.

Type - The type of server or CIM. For blade chassis, the type can
be Blade Chassis, Blade, BladeChassisAdmin, and
BladeChassisURL. Type also includes TierDevice and
KVMSwitch.

Availability - The Availability can be Idle, Connected, Busy, or
Unavailable. Blade servers will have an availability of either
shared or exclusive when a connection to that blade is in place.
2. Click View by Port, View by Group or View by Search to switch
between views.
3. Click the Port Name of the target server you want to access. The
Port Action Menu appears. See Port Action Menu (on page 44) for
details on available menu options.
4. Choose the desired menu command from the Port Action Menu.
To change the display sort order:

Click the column heading by which you want to sort. The list of KVM
target servers is sorted by that column.
43
Chapter 3: Working with Target Servers
Port Action Menu
When you click a Port Name in the Port Access list, the Port Action menu
appears. Choose the desired menu option for that port to execute it. Note
that only currently available options, depending on the port's status and
availability, will be listed in the Port Action menu:

Connect - Creates a new connection to the target server. For the
Dominion KX II Remote Console, a new Virtual KVM Client (on
page 52) page appears. For the Dominion KX II Local Console, the
display switches to the target server and switches away from the
local user interface. On the local port, the Dominion KX II Local
Console interface must be visible in order to perform the switch. Hot
key switching is also available from the local port.
Note: This option is not available from the Dominion KX II Remote
Console for an available port if all connections are busy.

Switch From - Switches from an existing connection to the selected
port (KVM target server). This menu item is available only for KVM
targets. This option is visible only when a Virtual KVM Client is
opened.
Note: This menu item is not available on the Dominion KX II Local
Console.

Disconnect - Disconnects this port and closes the Virtual KVM Client
page for this target server. This menu item is available only when the
port status is up and connected, or up and busy.
Note: This menu item is not available on the Dominion KX II Local
Console. The only way to disconnect from the switched target in the
Local Console is to use the hot key.
44

Power On - Powers on the target server through the associated
outlet. This option is visible only when there are one or more power
associations to the target.

Power Off - Powers off the target server through the associated
outlets. This option is visible only when there are one or more power
associations to the target, when the target power is on (port status is
up), and when user has permission to operate this service.

Power Cycle - Power cycles the target server through the associated
outlets. This option is visible only when there are one or more power
associations to the target, and when the user has permission to
operate this service.
Chapter 3: Working with Target Servers
Managing Favorites
A Favorites feature is provided so you can organize and quickly access
the devices you use frequently. The Favorite Devices section is located
in the lower left side (sidebar) of the Port Access page and provides the
ability to:

Create and manage a list of favorite devices

Quickly access frequently-used devices

List your favorites either by Device Name, IP Address, or DNS
hostname

Discover Dominion KX II devices on its subnet (before and after
login)

Retrieve discovered Dominion KX II devices from the connected KX
device (after login)
Note: This feature is available only on the Dominion KX II Remote
Console (not the Dominion KX II Local Console or AKC).
To access a favorite Dominion KX II device:

Click the device name (listed beneath Favorite Devices). A new
browser opens to that device.
To display favorites by name:

Click Display by Name.
To display favorites by IP Address:

Click Display by IP.
To display favorites by the host name:

Click Display by Host Name.
45
Chapter 3: Working with Target Servers
Note: Both IPv4 and IPv6 addresses are supported.
Manage Favorites Page
To open the Manage Favorites page:

Click the Manage button in the left panel. The Manage Favorites
page appears and contains the following:
Use:
To:
Favorites List
Manage your list of favorite
devices.
Discover Devices - Local Subnet
Discover Raritan devices on the
client PC's local subnet.
Discover Devices - Dominion KX
II Subnet
Discover the Raritan devices on
the Dominion KX II device subnet.
Add New Device to Favorites
Add, edit, and delete devices from
your list of Favorites.
Favorites List Page
From the Favorites List page, you can add, edit, and delete devices from
your list of favorites.
To open the Favorites List page:

46
Choose Manage > Favorites List. The Favorites List page opens.
Chapter 3: Working with Target Servers
Discovering Devices on the Local Subnet
This option discovers the devices on your local subnet, which is the
subnet where the Dominion KX II Remote Console is running. These
devices can be accessed directly from this page or you can add them to
your list of favorites. See Favorites List Page (on page 46).
To discover devices on the local subnet:
1. Choose Manage > Discover Devices - Local Subnet. The Discover
Devices - Local Subnet page appears.
2. Choose the appropriate discovery port:

To use the default discovery port, select the Use Default Port
5000 checkbox.

To use a different discovery port:
a. Deselect the Use Default Port 5000 checkbox.
b. Type the port number in the Discover on Port field.
c.
Click Save.
3. Click Refresh. The list of devices on the local subnet is refreshed.
To add devices to your Favorites List:
1. Select the checkbox next to the device name/IP address.
2. Click Add.
Tip: Use the Select All and Deselect All buttons to quickly select all (or
deselect all) devices in the remote console subnet.
To access a discovered device:

Click the device name or IP address for that device. A new browser
opens to that device.
47
Chapter 3: Working with Target Servers
Note: Both IPv4 and IPv6 addresses are supported.
Discovering Devices on the Dominion KX II Subnet
This option discovers devices on the device subnet, which is the subnet
of the Dominion KX II device IP address itself. You can access these
devices directly from this the Subnet page or add them to your list of
favorites. See Favorites List Page (on page 46).
This feature allows multiple Dominion KX II devices to interoperate and
scale automatically. The Dominion KX II Remote Console automatically
discovers the Dominion KX II devices, and any other Raritan device, in
the subnet of the Dominion KX II.
To discover devices on the device subnet:
1. Choose Manage > Discover Devices - Dominion KX II Subnet. The
Discover Devices - Dominion KX II Subnet page appears.
2. Click Refresh. The list of devices on the local subnet is refreshed.
To add devices to your Favorites List:
1. Select the checkbox next to the device name/IP address.
2. Click Add.
Tip: Use the Select All and Deselect All buttons to quickly select all (or
deselect all) devices in the Dominion KX II device subnet.
To access a discovered device:

Click the device name or IP address for that device. A new browser
opens to that device.
Note: Both IPv4 and IPv6 addresses are supported.
Adding, Deleting and Editing Favorites
To add a device to your favorites list:
1. Choose Manage > Add New Device to Favorites. The Add New
Favorite page appears.
48
Chapter 3: Working with Target Servers
2. Type a meaningful description.
3. Type the IP Address/Host Name for the device.
4. Change the discovery Port (if necessary).
5. Select the Product Type.
6. Click OK. The device is added to your list of favorites.
To edit a favorite:
1. From the Favorites List page, select the checkbox next to the
appropriate Dominion KX II device.
2. Click the Edit button. The Edit page appears.
3. Update the fields as necessary:

Description

IP Address/Host Name - Type the IP address of the Dominion KX
II device

Port (if necessary)

Product Type
4. Click OK.
To delete a favorite:
Important: Exercise caution in the removal of favorites. You are not
prompted to confirm their deletion.
1. Select the checkbox next to the appropriate Dominion KX II device.
49
Chapter 3: Working with Target Servers
2. Click the Delete button. The favorite is removed from your list of
favorites.
Note: Both IPv4 and IPv6 addresses are supported.
Logging Out
To quit the Dominion KX II Remote Console:

Click Logout in the upper right-hand corner of the page.
Note: Logging out also closes any open Virtual KVM Client and serial
client sessions.
Proxy Server Configuration for use with Dominion KX II, MPC, VKC and
AKC
When the use of a Proxy Server is required, a SOCKS proxy must also
be provided and configured on the remote client PC.
Note: If the installed proxy server is only capable of the HTTP proxy
protocol, you will not be able to connect.
To configure the SOCKS proxy:
1. On the client, select Control Panel > Internet Options.
a. On the Connections tab, click 'LAN settings'. The Local Area
Network (LAN) Settings dialog opens.
b. Select 'Use a proxy server for your LAN'.
c.
Click Advanced. The Proxy Settings dialog opens.
d. Configure the proxy servers for all protocols. IMPORTANT: Do not
select 'Use the same proxy server for all protocols'.
Note: The default port for a SOCKS proxy (1080) is different from
HTTP proxy (3128).
2. Click OK at each dialog to apply the settings.
3. Next, configure the proxies for Java™ applets by selecting Control
Panel > Java.
e. On the General tab, click Network Settings. The Network Settings
dialog opens.
f.
Select Use Proxy Server.
g. Click Advanced. The Advanced Network Settings dialog opens.
h. Configure the proxy servers for all protocols. IMPORTANT: Do not
select 'Use the same proxy server for all protocols'.
50
Chapter 3: Working with Target Servers
Note: The default port for a SOCKS proxy (1080) is different from
HTTP proxy (3128).
4. If you are using standalone MPC, you must also do the following:
i.
Open the start.bat file in MPC directory with a text editor.
j.
Insert the following parameters to the command line. Add them
before "-classpath": -DsocksProxyHost=&lt;socks proxy ip addr&gt;
-DsocksProxyPort=&lt;socks proxy port&gt;
The parameters should look as follows:
start javaw -Xmn128M -Xmx512M -XX:MaxHeapFreeRatio=70
-XX:MinHeapFreeRatio=50 -Dsun.java2d.noddraw=true
-DsocksProxyHost=192.168.99.99 -DsocksProxyPort=1080
-classpath .\sdeploy.jar;.\sFoxtrot.jar;.\jaws.jar;.\sMpc.jar
com.raritan.rrc.ui.RRCApplication %1
Multi-Platform Client Interface
Raritan Multi-Platform Client (MPC) is a graphical user interface for the
Raritan product lines, providing remote access to target servers
connected to Raritan KVM over IP devices. For details on using MPC,
see the KVM and Serial Access Clients Guide available on Raritan's
website on the same page as the user guide. Instructions on launching
MPC are provided there.
Launching MPC from a Web Browser
Important: Regardless of the browser you use, you must allow
pop-ups from the Dominion device's IP address in order to open
MPC.
Important: Only Mac 10.5 and 10.6 with an Intel® processor can run
JRE 1.6 and, therefore, be used as a client. Mac 10.4.11 and 10.5.8
do not support MPC as a standalone client.
1. To open MPC from a client running any supported browser, type
http://IP-ADDRESS/mpc into the address line, where IP-ADDRESS
is the IP address of your Raritan device. MPC will open in a new
window.
Note: The Alt+Tab command will toggle between windows only on
the local system.
When MPC opens, the Raritan devices that were automatically
detected and which are found on your subnet are displayed in the
Navigator in tree format.
2. If your device is not listed by name in the navigator, add it manually:
a. Choose Connection > New Profile. The Add Connection window
opens.
51
Chapter 3: Working with Target Servers
b. In the Add Connection window, type a device Description,
specify a Connection Type, add the device IP address, and click
OK. These specifications can be edited later.
3. In the Navigator panel on the left of the page, double-click the icon
that corresponds to your Raritan device to connect to it.
Note: Depending on your browser and browser security settings, you
may see various security and certificate check and warning messages. It
is necessary to accept the options in order to open MPC.
Note: If you are using Firefox 3.0.3, you may experience problems
launching the application. If this occurs, clear the browser cache and
launch the application again.
Virtual KVM Client
Overview
Whenever you access a target server using the Remote Console, a
Virtual KVM Client (VKC) window opens. There is one Virtual KVM Client
for each target server connected. These windows can be accessed via
the Windows® task bar.
Virtual KVM Client windows can be minimized, maximized, and moved
around your computer desktop.
Note: Refreshing your HTML browser will close the Virtual KVM Client
connection, so exercise caution.
Note: If you are using Firefox 3.0.3, you may experience problems
launching the application. If this occurs, clear the browser cache and
launch the application again.
Connecting to a KVM Target Server
To connect to a KVM target server:
1. From the Dominion KX II Remote Console, click the Port Access tab
to open it. The Port Access page opens.
2. Click the Port Name of the target you want to access. The Port
Action menu appears.
3. Click Connect. A Virtual KVM Client (on page 52) window opens to
the target server connected to that port.
52
Chapter 3: Working with Target Servers
VKC Toolbar
Note: The KX II-101 VKC interface is different from the other Dominion
KX products. See VKC Toolbar for the KX II-101.
Button
Button
Name
Connection
Properties
Description
Video
Settings
Opens the Video Settings dialog, allowing you to
manually adjust video conversion parameters.
Color
Calibration
Adjusts color settings to reduce excess color
noise.
Opens the Modify Connection Properties dialog
from which you can manually adjust bandwidth
options (such as connection speed, color depth,
and so forth).
Same as choosing Video > Color Calibrate.
Target
Screenshot
Click to take a screenshot of the target server
and save it to a file of your choosing.
Synchronize
Mouse
In dual-mouse mode, forces realignment of the
target server mouse pointer with the mouse
pointer.
Refresh
Screen
Forces a refresh of the video screen.
Auto-sense
Video
Settings
Forces a refresh of the video settings (resolution,
refresh rate).
Smart Card
Opens a dialog that allows you to select from a
list of smart card readers connected to a client
PC.
Note: This function is only available on the KX II
2.1.10 or later.
Send
Ctrl+Alt+Del
Sends a Ctrl+Alt+Del hot key combination to the
target server.
Single Cursor Starts Single Cursor mode in which the local
Mode
mouse pointer no longer appears onscreen.
Press Ctrl+Alt+O to exit this mode.
Alternatively, choose Single/Double Cursor
from the shortcut menu, which is opened by
pressing Ctrl+Left Alt+M.
Full Screen
Mode
Maximizes the screen real estate to view the
target server desktop.
53
Chapter 3: Working with Target Servers
Button
Button
Name
Scaling
Description
Increases or reduces the target video size so you
can view the entire contents of the target server
window without using the scroll bar.
Switching Between KVM Target Servers
With the Dominion KX II, you can access several KVM target servers.
The Dominion KX II provides the ability to switch from one target server
to another.
Note: This feature is available in the Dominion KX II Remote Console
only.
To switch between KVM target servers:
1. While already using a target server, access the Dominion KX II Port
Access page.
2. Click the port name of the target you want to access. The Port Action
menu appears.
3. Choose Switch From in the Port Action menu. The Virtual KVM
Client window switches to the new target server you selected.
Power Controlling a Target Server
Note: These features are available only when you have made power
associations.
To power cycle a KVM target server:
1. From the Dominion KX II Remote Console, click the Port Access tab.
The Port Access page opens.
2. Click the Port Name of the appropriate target server. The Port Action
menu appears.
3. Choose Power Cycle. A confirmation message appears.
To power on a target server:
1. From the Dominion KX II Remote Console, click the Port Access tab.
The Port Access page opens.
2. Click the port name of the appropriate target server. The Port Action
menu appears.
3. Choose Power On. A confirmation message appears.
54
Chapter 3: Working with Target Servers
To power off a target server:
1. From the Dominion KX II Remote Console, click the Port Access tab
to open it. The Port Access page opens.
2. Click the port name of the appropriate target server. The Port Action
menu appears.
3. Choose Power Off. A confirmation message appears.
Disconnecting KVM Target Servers
Note: This item is not available on the Dominion KX II Local Console.
The only way to disconnect from the switched target in the Local Console
is to use the hot key.
To disconnect a target server:
1. Click the port name of the target you want to disconnect. The Port
Action menu appears.
2. Choose Disconnect.
Tip: You can also close the Virtual KVM Client window by selecting
Connection > Exit from the Virtual KVM menu.
55
Chapter 3: Working with Target Servers
Choosing USB Profiles
When you connect to a KVM target server for the first time, as described
in Connecting to a KVM Target Server (on page 52), the preferred
USB profile for the port is automatically used. If you have connected to
the target server previously using a different profile, the USB profile from
the last connection is used. You are alerted to the use of a profile other
than the preferred profile by a warning similar to the following:
After you have connected to a target server, you can change the USB
profile as necessary. By default, the profiles that appear under the USB
Profile menu in the VKC are those that you are most likely to use. These
profiles have been preselected by the administrator for use with the
connected target server, based on your operational requirements.
However, all profiles are available to be selected via the Other Profiles
option on the USB Profile menu.
To choose a USB profile:
1. Connect to a KVM target server as described in Connecting to a
KVM Target Server (on page 52).
2. In VKC, choose a USB profile from the USB Profile menu.
The name of the profile indicates the operating system or server with
which it should be used. See USB Profiles (on page 100) for details
on USB profiles.
56
Chapter 3: Working with Target Servers
Connection Properties
The dynamic video compression algorithms maintain KVM console
usability under varying bandwidth constraints. The devices optimize KVM
output not only for LAN use, but also for WAN use. These devices can
also control color depth and limit video output, offering an optimal
balance between video quality and system responsiveness for any
bandwidth.
The parameters in the Properties dialog can be optimized to suit your
needs for different operating environments. Connection properties are
saved across subsequent connections to generation 2 devices once they
are set and saved.
Note: VKC for the KX II-101 uses an icon set that differs from the icon
set used in VKC for other Dominion KX products. See VKC Toolbar for
the KX II-101 for additional information.
To set the connection properties:
1. Choose Connection > Properties or click the Connection Properties
button
in the toolbar. The Properties dialog appears.
Note: KX II-101 does not support 1G Ethernet.
Note: VKC for the KX II-101 uses an icon set that differs from the
icon set used in VKC for other Dominion KX products. See VKC
Toolbar for the KX II-101 for additional information.
2. Choose the Connection Speed from the drop-down list. The device
can automatically detect available bandwidth and not limit bandwidth
use. However, you can also adjust this usage according to
bandwidth limitations.

Auto

1G Ethernet

100 Mb Ethernet
57
Chapter 3: Working with Target Servers

10 Mb Ethernet

1.5 Mb (MAX DSL/T1)

1 Mb (Fast DSL/T1)

512 Kb (Medium DSL/T1)

384 Kb (Slow DSL/T1)

256 Kb (Cable)

128 Kb (Dual ISDN)

56 kb (ISP Modem)

33 kb (Fast Modem)

24 kb (Slow Modem)
Note that these settings are an optimization for specific conditions
rather than an exact speed. The client and server always attempt to
deliver video as quickly as possible on the network regardless of the
current network speed and encoding setting. But the system will be
most responsive when the settings match the real world environment.
3. Choose the Color Depth from the drop-down list. The device can
dynamically adapt the color depth transmitted to remote users in
order to maximize usability in all bandwidths.

15-bit RGB Color

8-bit RGB Color

4-bit Color

4-bit Gray

3-bit Gray

2-bit Gray

Black and White
Important: For most administrative tasks (server monitoring,
reconfiguring, and so on), the full 24-bit or 32-bit color spectrum
made available by most modern video graphics cards is not
necessary. Attempting to transmit such high color depths wastes
network bandwidth.
4. Use the slider to select the desired level of Smoothing (15-bit color
mode only). The level of smoothing determines how aggressively to
blend screen regions with small color variation into a single smooth
color. Smoothing improves the appearance of target video by
reducing displayed video noise.
5. Click OK to set these properties.
58
Chapter 3: Working with Target Servers
Connection Information
To obtain information about your Virtual KVM Client
connection:

Choose Connection > Connection Info. The Connection Info window
opens.
The following information is displayed about the current connection:

Device Name - The name of the device.

IP Address - The IP address of the device.

Port - The KVM communication TCP/IP port used to access the
target device.

Data In/Second - Data rate in.

Data Out/Second - Data rate out.

Connect Time - The duration of the connect time.

FPS - The frames per second transmitted for video.

Horizontal Resolution - The screen resolution horizontally.

Vertical Resolution - The screen resolution vertically.

Refresh Rate - How often the screen is refreshed.

Protocol Version - RFB Protocol version.
To copy this information:

Click Copy to Clipboard. The information is available to be pasted
into the program of your choice.
Keyboard Options
Keyboard Macros
Keyboard macros ensure that keystroke combinations intended for the
target server are sent to and interpreted only by the target server.
Otherwise, they might be interpreted by the computer on which the
Virtual KVM Client is running (your client PC).
Macros are stored on the client PC and are PC-specific. Therefore, if you
use another PC, you will not see your macros. In addition, if another
person uses your PC and logs in under a different name, that user will
see your macros since they are computer-wide.
Keyboard macros created in the Virtual KVM Client are available in MPC
and vice versa. However, keyboard macros created in AKC cannot be
used in VKC or MPC, and vice versa.
59
Chapter 3: Working with Target Servers
Building a Keyboard Macro
To build a macro:
1. Click Keyboard > Keyboard Macros. The Keyboard Macros dialog
appears.
2. Click Add. The Add Keyboard Macro dialog appears.
3. Type a name for the macro in the Keyboard Macro Name field. This
name will appear in the Keyboard menu after it is created.
4. From the Hot-Key Combination field, select a keyboard combination
from the drop-down list. This allows you to execute the macro with a
predefined keystroke. Optional
5. In the Keys to Press drop-down list, select each key you would like to
use to emulate the keystrokes that will be used to perform the
command. Select the keys in the order by which they are to be
pressed. After each selection, select Add Key. As each key is
selected, it will appear in the Macro Sequence field and a Release
Key command will automatically be added after each selection.
6. To use the Send Text to Target function for the macro, click the
Construct Macro from Text button.
7. For example, create a macro to close a window by selecting Left Ctrl
+ Esc. This will appear in the Macro Sequence box as follows:
Press Left Ctrl
Release Left Ctrl
Press Esc
Release Esc
8. Review the Macro Sequence field to be sure the macro sequence is
defined correctly.
a. To remove a step in the sequence, select it and click Remove.
b. To change the order of steps in the sequence, click the step and
then click the up or down arrow buttons to reorder them as
needed.
9. Click OK to save the macro. Click Clear to clear all field and start
over. When you click OK, the Keyboard Macros dialog appears and
lists the new keyboard macro.
60
Chapter 3: Working with Target Servers
10. Click Close to close the Keyboard Macros dialog. The macro will now
appear on the Keyboard menu in the application. Select the new
macro on the menu to run it or use the keystrokes you assigned to
the macro.
Running a Keyboard Macro
Once you have created a keyboard macro, execute it using the keyboard
macro you assigned to it or by choosing it from the Keyboard menu.
Run a Macro from the Menu Bar
When you create a macro, it appears under the Keyboard menu.
Execute the keyboard macro by clicking on it in the Keyboard menu.
Run a Macro Using a Keyboard Combination
If you assigned a keyboard combination to a macro when building it, you
can execute the macro by pressing its assigned keystrokes. For
example, press the keys Ctrl+Alt+0 simultaneously to minimize all
windows on a Windows target server.
Modifying and Removing Keyboard Macros
To modify a macro:
1. Choose Keyboard > Keyboard Macros. The Keyboard Macros dialog
appears.
2. Choose the macro from among those listed.
3. Click Modify. The Add/Edit Macro dialog appears.
4. Make your changes.
5. Click OK.
61
Chapter 3: Working with Target Servers
To remove a macro:
1. Choose Keyboard > Keyboard Macros. The Keyboard Macros dialog
appears.
2. Choose the macro from among those listed.
3. Click Remove. The macro is deleted.
Hot-key combinations that coincide with blade chassis switching key
sequences will not be sent to blades housed in those chassis.
Setting CIM Keyboard/Mouse Options
To access the DCIM-USBG2 setup menu:
1. Put the mouse focus on a window such as Note Pad (Windows®
operating system) or an equivalent.
2. Select Set CIM Keyboard/Mouse options. This is the equivalent of
sending the Left-Control and Num Lock to the target. The CIM setup
menu options are then displayed.
3. Set the language and mouse settings.
4. Exit the menu to return to normal CIM functionality.
Video Properties
Refresh Screen
The Refresh Screen command forces a refresh of the video screen.
Video settings can be refreshed automatically in several ways:

The Refresh Screen command forces a refresh of the video screen.

The Auto-sense Video Settings command automatically detects the
target server's video settings.

The Calibrate Color command calibrates the video to enhance the
colors being displayed.
In addition, you can manually adjust the settings using the Video Settings
command.
Note: VKC for the KX II-101 uses an icon set that differs from the icon
set used in VKC for other Dominion KX products. See VKC Toolbar for
the KX II-101 for additional information.
To refresh the video settings, do one of the following:

Choose Video > Refresh Screen or click the Refresh Screen button
in the toolbar.
62
Chapter 3: Working with Target Servers
Auto-Sense Video Settings
The Auto-sense Video Settings command forces a re-sensing of the
video settings (resolution, refresh rate) and redraws the video screen.
Note: VKC for the KX II-101 uses an icon set that differs from the icon
set used in VKC for other Dominion KX products. See VKC Toolbar for
the KX II-101 for additional information.
To automatically detect the video settings, do the following:

Choose Video > Auto-sense Video Settings or click the Auto-Sense
Video Settings button
in the toolbar. A message stating that the
auto adjustment is in progress appears.
Calibrating Color
Use the Calibrate Color command to optimize the color levels (hue,
brightness, saturation) of the transmitted video images. The color
settings are on a target server-basis.
Note: The Calibrate Color command applies to the current connection
only.
Note: The KX II-101 does support color calibration.
To calibrate the color, do the following:

Choose Video > Calibrate Color or click the Calibrate Color button
in the toolbar. The target device screen updates its color
calibration.
Adjusting Video Settings
Use the Video Settings command to manually adjust the video settings.
To change the video settings:
1. Choose Video > Video Settings or click the Video Settings button
in the toolbar to open the Video Settings dialog.
2. Adjust the following settings as required. As you adjust the settings
the effects are immediately visible:
a. Noise Filter
63
Chapter 3: Working with Target Servers
The device can filter out the electrical interference of video output
from graphics cards. This feature optimizes picture quality and
reduces bandwidth. Higher settings transmit variant pixels only if
a large color variation exists in comparison to the neighboring
pixels. However, setting the threshold too high can result in the
unintentional filtering of desired screen changes.
Lower settings transmit most pixel changes. Setting this
threshold too low can result in higher bandwidth use.
b. PLL Settings
Clock - Controls how quickly video pixels are displayed across
the video screen. Changes made to clock settings cause the
video image to stretch or shrink horizontally. Odd number
settings are recommended. Under most circumstances this
setting should not be changed because the autodetect is usually
quite accurate.
Phase - Phase values range from 0 to 31 and will wrap around.
Stop at the phase value that produces the best video image for
the active target server.
c.
Brightness: Use this setting to adjust the brightness of the target
server display.
d. Brightness Red - Controls the brightness of the target server
display for the red signal.
e. Brightness Green - Controls the brightness of the green signal.
f.
Brightness Blue - Controls the brightness of the blue signal.
g. Contrast Red - Controls the red signal contrast.
h. Contrast Green - Controls the green signal.
i.
Contrast Blue - Controls the blue signal.
If the video image looks extremely blurry or unfocused, the
settings for clock and phase can be adjusted until a better image
appears on the active target server.
Warning: Exercise caution when changing the Clock and Phase
settings. Doing so may result in lost or distorted video and you may
not be able to return to the previous state. Contact Raritan Technical
Support before making any changes.
j.
Horizontal Offset - Controls the horizontal positioning of the
target server display on your monitor.
k.
Vertical Offset - Controls the vertical positioning of the target
server display on your monitor.
3. Select Automatic Color Calibration to enable this feature.
4. Select the video sensing mode:
64
Chapter 3: Working with Target Servers

Best possible video mode
The device will perform the full Auto Sense process when
switching targets or target resolutions. Selecting this option
calibrates the video for the best image quality.

Quick sense video mode
With this option, the device will use a quick video Auto Sense in
order to show the target's video sooner. This option is especially
useful for entering a target server's BIOS configuration right after
a reboot.
5. Click OK to apply the settings and close the dialog. Click Apply to
apply the settings without closing the dialog.
65
Chapter 3: Working with Target Servers
Note: Some Sun background screens, such as screens with very dark
borders, may not center precisely on certain Sun servers. Use a different
background or place a lighter colored icon in the upper left corner of the
screen.
Note: VKC for the KX II-101 uses an icon set that differs from the icon
set used in VKC for other Dominion KX products. See VKC Toolbar for
the KX II-101 for additional information.
66
Chapter 3: Working with Target Servers
Using Screenshot from Target
You are able to take a screenshot of a target server using the
Screenshot from Target server command. You can then save this
screenshot to a file location of your choosing as a bitmap, JPEG or PNG
file.
Note: The Screenshot from Target function is not available for the KX
II-101.
To take a screenshot of the target server:
1. Select Video > Screenshot from Target or click the Screenshot from
Target button
on the toolbar.
2. In the Save dialog, choose the location to save the file, name the file,
and select a file format from the 'Files of type' drop-down.
3. Click Save to save the screenshot.
67
Chapter 3: Working with Target Servers
Changing the Maximum Refresh Rate
If the video card you are using on the target uses custom software and
you are accessing the target through MPC or VKC, you may need to
change the maximum refresh rate of the monitor in order for the refresh
rate to take affect on the target.
To adjust the monitor refresh rate:
1. In Windows®, select Display Properties > Settings > Advanced to
open the Plug and Play dialog.
2. Click on the Monitor tab.
3. Set the 'Screen refresh rate' to any rate above 100Hz.
4. Click OK and then OK again to apply the setting.
Mouse Options
When controlling a target server, the Remote Console displays two
mouse cursors: one belonging to your client workstation and the other
belonging to the target server.
You can operate in either single mouse mode or dual mouse mode.
When in dual mouse mode, and provided the option is properly
configured, the mouse cursors will align.
When there are two mouse cursors, the device offers several mouse
modes:
68

Absolute (Mouse Synchronization)

Intelligent (Mouse Mode)

Standard (Mouse Mode)
Chapter 3: Working with Target Servers
Mouse Pointer Synchronization
When remotely viewing a target server that uses a mouse, you will see
two mouse cursors: one belonging to your remote client workstation and
the other belonging to the target server. When the mouse pointer lies
within the Virtual KVM Client target server window, mouse movements
and clicks are directly transmitted to the connected target server. While
in motion, the client mouse pointer slightly leads the target mouse pointer
due to mouse acceleration settings.
On fast LAN connections, you may want to disable the Virtual KVM
Client mouse pointer and view only the target server's pointer. You can
toggle between these two modes (single mouse and dual mouse).
Note: VKC for the KX II-101 uses an icon set that differs from the icon
set used in VKC for other Dominion KX products. See VKC Toolbar for
the KX II-101 for additional information.
Mouse Synchronization Tips
Be sure to follow these steps when configuring mouse synchronization:
1. Verify that the selected video resolution and refresh rate are among
those supported by the device. The Virtual KVM Client Connection
Info dialog displays the actual values that the device is seeing.
2. Verify that the cable length is within the specified limits for the
selected video resolution.
3. Verify that the mouse and video have been properly configured
during the installation process.
4. Force an auto-sense by clicking the Virtual KVM Client auto-sense
button.
5. If that does not improve the mouse synchronization (for Linux, UNIX,
and Solaris KVM target servers):
a. Open a terminal window.
b. Enter the xset mouse 1 1 command.
c.
Close the terminal window.
6. Click the "Virtual KVM Client mouse synchronization" button
.
69
Chapter 3: Working with Target Servers
Additional Notes for Intelligent Mouse Mode

Be sure that there are no icons or applications in the upper left
section of the screen since that is where the synchronization routine
takes place.

Do not use an animated mouse.

Disable active desktop on KVM target servers.
Synchronize Mouse
In dual mouse mode, the Synchronize Mouse command forces
realignment of the target server mouse pointer with Virtual KVM Client
mouse pointer.
To synchronize the mouse, do one of the following:

Choose Mouse > Synchronize Mouse or click the Synchronize
Mouse button
in the toolbar.
Standard Mouse Mode
Standard Mouse mode uses a standard mouse synchronization
algorithm using relative mouse positions. Standard Mouse mode requires
that mouse acceleration is disabled and other mouse parameters are set
correctly in order for the client and server mouse to stay synchronized.
Standard Mouse mode is the default.
To enter Standard Mouse mode:

70
Choose Mouse > Standard.
Chapter 3: Working with Target Servers
Intelligent Mouse Mode
In Intelligent Mouse mode, the device can detect the target mouse
settings and synchronize the mouse cursors accordingly, allowing mouse
acceleration on the target. In this mode, the mouse cursor does a
“dance” in the top left corner of the screen and calculates the
acceleration. For this mode to work properly, certain conditions must be
met.
To enter intelligent mouse mode:

Choose Mouse > Intelligent.
Intelligent Mouse Synchronization Conditions
The Intelligent Mouse Synchronization command, available on the
Mouse menu, automatically synchronizes mouse cursors during
moments of inactivity. For this to work properly, however, the following
conditions must be met:

The active desktop should be disabled on the target.

No windows should appear in the top left corner of the target page.

There should not be an animated background in the top left corner of
the target page.

The target mouse cursor shape should be normal and not animated.

The target mouse speeds should not be set to very slow or very high
values.

Advanced mouse properties such as “Enhanced pointer precision" or
“Snap mouse to default button in dialogs” should be disabled.

Choose “Best Possible Video Mode” in the Video Settings window.

The edges of the target video should be clearly visible (that is, a
black border should be visible between the target desktop and the
remote KVM console window when you scroll to an edge of the
target video image).

When using the intelligent mouse synchronization function, having a
file icon or folder icon located in the upper left corner of your desktop
may cause the function not to work properly. To be sure to avoid any
problems with this function, Raritan recommends you do not have file
icons or folder icons in the upper left corner of your desktop.
After autosensing the target video, manually initiate mouse
synchronization by clicking the Synchronize Mouse button on the toolbar.
This also applies when the resolution of the target changes if the mouse
cursors start to desync from each other.
If intelligent mouse synchronization fails, this mode will revert to standard
mouse synchronization behavior.
71
Chapter 3: Working with Target Servers
Please note that mouse configurations will vary on different target
operating systems. Consult your OS guidelines for further details. Also
note that intelligent mouse synchronization does not work with UNIX
targets.
Absolute Mouse Mode
In this mode, absolute coordinates are used to keep the client and target
cursors in sync, even when the target mouse is set to a different
acceleration or speed. This mode is supported on servers with USB
ports.
To enter absolute mouse mode:

Choose Mouse > Absolute.
Note: The absolute mouse setting requires a USB target system and is
the recommended mouse setting for KX II-101.
Note: Absolute Mouse Synchronization is available for use with the
virtual media-enabled USB CIM (D2CIM-VUSB and D2CIM-DVUSB)
only.
Single Mouse Cursor
Single Mouse mode uses only the target server mouse cursor and the
local mouse pointer no longer appears onscreen. While in single mouse
mode, the Synchronize Mouse command is not available (there is no
need to synchronize a single mouse cursor).
Note: VKC for the KX II-101 uses an icon set that differs from the icon
set used in VKC for other Dominion KX products. See VKC Toolbar for
the KX II-101 for additional information.
To enter single mouse mode, do the following:
1. Choose Mouse > Single Mouse Cursor.
72
Chapter 3: Working with Target Servers
2. Click the Single/Double Mouse Cursor button
in the toolbar.
To exit single mouse mode:
1. Press Ctrl+Alt+O on your keyboard to exit single mouse mode.
VKC Virtual Media
See the chapter on Virtual Media for complete information about setting
up and using virtual media.
73
Chapter 3: Working with Target Servers
Smart Cards (VKC, AKC and MPC)
Using the KX II 2.1.10 or later, you are able to mount a smart card reader
onto a target server to support smart card authentication and related
applications. For a list of supported smart cards, smart card readers, and
additional system requirements, see Supported and Unsupported
Smart Card Readers (on page 276).
When accessing a server remotely, you will have the opportunity to
select an attached smart card reader and mount it onto the server. Smart
card authentication is used with the target server, it is not used to log into
the device. Therefore, changes to smart card PIN and credentials do not
require updates to device accounts. When mounted onto the target
server, the card reader and smart card will cause the server to behave
as if they had been directly attached. Removal of the smart card or smart
card reader will cause the user session to be locked or you will be logged
out depending on how the card removal policy has been setup on the
target server OS. When the KVM session is terminated, either because it
has been closed or because you switch to a new target, the smart card
reader will be automatically unmounted from the target server.
When PC-Share mode is enabled on the device, multiple users can
share access to a target server. However, when a smart card reader is
connected to a target, the device will enforce privacy regardless of the
PC-Share mode setting. In addition, if you join a shared session on a
target server, the smart card reader mounting will be disabled until
exclusive access to the target server becomes available.
After a KVM session is established to the target server, a Smart Card
menu and button are available in the Virtual KVM Client and
Multi-Platform Client. Once the menu is opened or the Smart Card button
is selected, the smart card readers that have been detected as attached
to the remote client are displayed. From this dialog you can attach
additional smart card readers, refresh the list of smart card readers
attached to the target, and detach smart card readers. You are also able
to remove or reinsert a smart card. This function can be used to provide
notification to a target server OS that requires a removal/reinsertion in
order to display the appropriate login dialog. Using this function allows
the notification to be sent to a single target without affecting other active
KVM sessions.
To mount a smart card reader:
1. Click the Smart Card menu and then select Smart Card Reader.
Alternatively, click the Smart Card button
in the toolbar.
2. Select the smart card reader from the Select Smart Card Reader
dialog.
3. Click Mount.
74
Chapter 3: Working with Target Servers
4. A progress dialog will open. Check the 'Mount selected card reader
automatically on connection to targets' checkbox to mount the smart
card reader automatically the next time you connect to a target. Click
OK to begin the mounting process.
To update the smart card in the Select Smart Card Reader
dialog:

Click Refresh List if a new smart card reader has been attached to
the client PC.
To send smart card remove and reinsert notifications to the
target:

Select the smart card reader that is currently mounted and click the
Remove/Reinsert button.
To unmount a smart card reader:

Select the smart card reader to be unmounted and click the Unmount
button.
Smart card reader mounting is also supported from the Local Console.
See Local Console Smart Card Access (on page 242) in the KX II
Help.
75
Chapter 3: Working with Target Servers
Tool Options
From the Tools menu, you can specify certain options for use with the
Virtual KVM Client, including logging, setting the keyboard type, and
defining hot keys for exiting Full Screen mode and Single Cursor mode.
To set the tools options:
1. Choose Tools > Options. The Options dialog appears.
2. Select the Enable Logging checkbox only if directed to by Technical
Support. This option creates a log file in your home directory.
3. Choose the Keyboard Type from the drop-down list (if necessary).
The options include:

US/International

French (France)

German (Germany)

Japanese

United Kingdom

Korean (Korea)

Belgian (Belgium)

Norwegian (Norway)

Portuguese (Portugal)

Danish (Denmark)

Swedish (Sweden)

German (Switzerland)

Hungarian (Hungary)

Spanish (Spain)

Italian (Italy)

Slovenian

Translation: French - US

Translation: French - US International
Note: In AKC, the keyboard type defaults to the local client, so this
option does not apply.
4. Exit Full Screen Mode - Hotkey. When you enter Full Screen mode,
the display of the target server becomes full screen and acquires the
same resolution as the target server. This is the hot key used for
exiting this mode.
76
Chapter 3: Working with Target Servers
5. Exit Single Cursor Mode - Hotkey. When you enter single cursor
mode, only the target server mouse cursor is visible. This is the hot
key used to exit single cursor mode and bring back the client mouse
cursor. Click OK.
Client Launch Settings
KX II users can also configure client launch settings that allow you to
define the size of the screen for a KVM session.
6. Select the Client Launch Settings tab.
a. To configure the target window settings:

Select 'Standard - sized to target Resolution' to open the window
using the target's current resolution. If the target resolution is
greater than the client resolution, the target window covers as
much screen area as possible and scroll bars are added (if
needed).

Select Full Screen to open the window in full screen mode.
a. To configure the monitor on which the target viewer is launched:

Select 'Monitor Client Was Launched from' if you want the target
viewer to be launched using the same display as the application
that is being used on the client (for example, a web browser or
applet).
7. Use Select From Detected Monitors to select from a list of target
monitors that are currently detected by the application. If a previously
selected monitor is no longer detected, 'Currently Selected Monitor
Not Detected' is displayed.
8. Click OK.
Keyboard Limitations
Slovenian Keyboards
The < key does not work on Slovenian keyboards due to a JRE
limitation.
Language Configuration on Linux
Because the Sun JRE on Linux has problems generating the correct Key
Events for foreign-language keyboards configured using System
Preferences, Raritan recommends that you configure foreign keyboards
using the methods described in the following table.
Language
Configuration method
US Intl
Default
French
Keyboard Indicator
German
System Settings (Control Center)
Japanese
System Settings (Control Center)
77
Chapter 3: Working with Target Servers
Language
Configuration method
UK
System Settings (Control Center)
Korean
System Settings (Control Center)
Belgian
Keyboard Indicator
Norwegian
Keyboard Indicator
Danish
Keyboard Indicator
Swedish
Keyboard Indicator
Hungarian
System Settings (Control Center)
Spanish
System Settings (Control Center)
Italian
System Settings (Control Center)
Slovenian
System Settings (Control Center)
Portuguese
System Settings (Control Center)
Note: The Keyboard Indicator should be used on Linux systems using
Gnome as a desktop environment.
78
Chapter 3: Working with Target Servers
View Options
View Toolbar
You can use the Virtual KVM client with or without the toolbar display.
To toggle the display of the toolbar (on and off):

Choose View > View Toolbar.
Scaling
Scaling your target window allows you to view the entire contents of the
target server window. This feature increases or reduces the size of the
target video to fit the Virtual KVM Client window size, and maintains the
aspect ratio so that you see the entire target server desktop without
using the scroll bar.
To toggle scaling (on and off):

Choose View > Scaling.
Target Screen Resolution
When you enter Full Screen mode, the target's full screen is displayed
and acquires the same resolution as the target server. The hot key used
for exiting this mode is specified in the Options dialog (the default is
Ctrl+Alt+M). While in Full Screen mode, moving your mouse to the top of
the screen will display the Full Screen mode menu bar.
To enter full screen mode:

Choose View > Full Screen.
To exit full screen mode:

Press the hot key configured in the Tools Options dialog. The default
is Ctrl+Alt+M. For AKC, select Connection/Exit from the hidden menu
bar, which is accessed by hovering your mouse at the top of the
screen.
Alternatively, if you want to access the target in full screen mode at all
times, you can make Full Screen mode the default.
To set Full Screen mode as the default mode:
1. Click Tools > Options to open the Options dialog.
2. Select Enable Launch in Full Screen Mode and click OK.
79
Chapter 3: Working with Target Servers
Help Options
About Raritan Virtual KVM Client
This menu command provides version information about the Virtual KVM
Client, in case you require assistance from Raritan Technical Support.
To obtain version information:
1. Choose Help > About Raritan Virtual KVM Client.
2. Use the Copy to Clipboard button to copy the information contained
in the dialog to a clipboard file so it can be accessed later when
dealing with support (if needed).
Active KVM Client (AKC)
Overview
The Microsoft Windows .NET-based Active KVM Client (AKC) is
available with the KX II 2.2 (or later) and supports all KX II models,
although the KX2-101 and KSX2 models are not currently supported.
AKC is based on Microsoft Windows .NET technology and allows users
to run the client in Windows environments without the use of the Java
Runtime Environment (JRE), which is required to run Raritan's Virtual
KVM and Multi-Platform clients. AKC also works with CC-SG.
AKC and VKC share similar features with the exception of the following:

Minimum system requirements

Supported operating systems and browsers

Keyboard macros created in AKC cannot be used in VKC.
See the Virtual KVM Client (on page 52) section for information on
using the available features of the application. If there is a difference
between how AKC functions as compared to VKC, it is noted in the topic.
Also see Enabling Direct Port Access (on page 143)and Enabling
the AKC Download Server Certificate Validation (on page 144) for
configuration information on using AKC.
Note: If you are using direct port access with AKC, you must open a new
browser window or browser tab for each target you want to access. If you
try to access another target by entering the DPA URL into the same
browser window or browser tab you are currently accessing a target
from, you will not be able to connect and may receive an error.
80
Chapter 3: Working with Target Servers
AKC Supported Operating Systems and Browsers
.NET Framework
AKC requires Windows .NET® version 3.5, and will work with both 3.5
and 4.0 installed.
Operating Systems
When launched from Internet Explorer® or as a standalone application,
AKC allows you to reach target servers via the KX II 2.2 (or later). AKC is
compatible with the following platforms running .NET Framework 3.5:

Windows XP® operating system

Windows Vista® operating system (up to 64 bit)

Windows 7® operating system (up to 64 bit)
Note: You must be using Windows 7 if WINDOWS PC FIPs is turned
on and you are accessing a target using AKC and a smartcard.
Since .NET is required to run AKC, if you do not have .NET installed or
you have an unsupported version of .NET installed, you will receive a
message instructing you to check the .NET version.
Browser

Internet Explorer 6 or later
If you attempt to open AKC from a browser other than IE 6 or later, you
will receive an error message instructing you to check your browser and
to switch to Internet Explorer.
81
Chapter 3: Working with Target Servers
Prerequisites for Using AKC
In order to use AKC:

Ensure the cookies from the IP address of the device that is being
accessed are not currently being blocked.

Windows Vista, Windows 7 and Windows 2008 server users should
ensure that the IP address of the device being accessed is included
in their browser's Trusted Sites Zone and that Protected Mode is not
on when accessing the device.
Enable AKC Download Server Certificate Validation
If the KX II (or CC-SG) administrator has enabled the Enable AKC
Download Server Certificate Validation option:

Administrators must upload a valid certificate to the KX II or generate
a self-signed certificate on the KX II. The certificate must have a
valid host designation.

Each user must add the CA certificate (or a copy of self-signed
certificate) to the Trusted Root CA store in their browser.
When launching AKC from the CC-SG Admin Client, you must have
JRE™ 1.6.0_10 or above.
82
Chapter 4
Power Strip (Rack PDU) Outlet
Control
In This Chapter
Overview ..................................................................................................83
Turning Outlets On/Off and Cycling Power .............................................84
Overview
The Dominion KX II allows you to control Raritan PX and RPC series
power strip outlets connected to the Dominion KX II through a
D2CIM-PWR.
Once a PX or RPC series is setup and then attached to the Dominion KX
II, the power strip and its outlets can be controlled from the Powerstrip
page in the Dominion KX II interface. This page is accessed by clicking
on the Power menu at the top of the page.
The Powerstrip page will display power strips attached to the Dominion
KX II for which the user has been granted appropriate port access
permissions. In the case of tiered configurations, the Powerstrip page will
display both power strips attached to the base and tiered Dominion KX
IIs, for which the user has been granted appropriate port access
permissions.
Note: For information on setting up a PX, see the Dominion PX User
Guide.
From the Powerstrip page, you are able to turn the outlets on and off, as
well as cycle their power. You are also able to view the following power
strip and outlet information:


Powerstrip Device Information:

Name

Model

Temperature

Current Amps

Maximum Amps

Voltage

Power in Watts

Power in Volts Ampere
Outlet Display Information:

Name - Named assigned to the outlet when it was configured.
83
Chapter 4: Power Strip (Rack PDU) Outlet Control

State - On of Off status of the outlet.

Control - Turn outlets on or off, or cycle their power.

Association - The ports associated with the outlet.
Initially, when you open the Powerstrip page, the power strips that are
currently connected to the Dominion KX II are displayed in the
Powerstrip drop-down. Additionally, information relating to the currently
selected power strip is displayed. If no power strips are connected to the
Dominion KX II, a message stating "No powerstrips found" will be
displayed in the Powerstrip Device section of the page.
Turning Outlets On/Off and Cycling Power
To turn an outlet on:
1. Click the Power menu to access the Powerstrip page.
2. From the Powerstrip drop-down, select the PX power strip you want
to turn on.
3. Click Refresh to view the power controls.
84
Chapter 4: Power Strip (Rack PDU) Outlet Control
4. Click On.
5. Click OK to close the Power On confirmation dialog. The outlet will
be turned on and its state will be displayed as 'on'.
To turn an outlet off:
1. Click Off.
2. Click OK on the Power Off dialog.
3. Click OK on the Power Off confirmation dialog. The outlet will be
turned off and its state will be displayed as 'off'.
To cycle the power of an outlet:
1. Click the Cycle button. The Power Cycle Port dialog opens.
85
Chapter 4: Power Strip (Rack PDU) Outlet Control
2. Click OK. The outlet will then cycle (note that this may take a few
seconds).
3. Once the cycling is complete the dialog will open. Click OK to close
the dialog.
86
Chapter 5
Virtual Media
In This Chapter
Overview ..................................................................................................88
Prerequisites for Using Virtual Media ......................................................91
Using Virtual Media via VKC and AKC in a Windows Environment ........92
Using Virtual Media .................................................................................93
File Server Setup (File Server ISO Images Only) ...................................94
Connecting to Virtual Media ....................................................................96
Disconnecting Virtual Media ....................................................................99
87
Chapter 5: Virtual Media
Overview
Virtual media extends KVM capabilities by enabling KVM target servers
to remotely access media from a client PC and network file servers. With
this feature, media mounted on a client PC and network file servers is
essentially "mounted virtually" by the target server. The target server can
then read from and write to that media as if it were physically connected
to the target server itself. In addition to data file support via virtual media
files are supported by virtual media via a USB connection.
Virtual media can include internal and USB-mounted CD and DVD
drives, USB mass storage devices, PC hard drives, and ISO images
(disk images).
Note: ISO9660 is the standard supported by Raritan. However, other ISO
standards can be used.
Virtual media provides the ability to perform additional tasks remotely,
such as:

Transferring files

Running diagnostics

Installing or patching applications

Complete installation of the operating system
This expanded KVM control eliminates most trips to the data center,
saving time and money, thereby making virtual media very powerful.
88
Chapter 5: Virtual Media
89
Chapter 5: Virtual Media
Diagram key
90
Desktop PC
CD/DVD drive
Dominion KX II
USB mass storage device
CIM
PC hard drive
Target server
Remote file server (ISO
images)
Chapter 5: Virtual Media
Prerequisites for Using Virtual Media
With the virtual media feature, you can mount up to two drives (of
different types) that are supported by the USB profile currently applied to
the target. These drives are accessible for the duration of the KVM
session.
For example, you can mount a specific CD-ROM, use it, and then
disconnect it when you are done. The CD-ROM virtual media “channel”
will remain open, however, so that you can virtually mount another
CD-ROM. These virtual media “channels” remain open until the KVM
session is closed as long as the USB profile supports it.
To use virtual media, connect/attach the media to the client or network
file server that you want to access from the target server. This need not
be the first step, but it must be done prior to attempting to access this
media.
The following conditions must be met in order to use virtual media:
Dominion Device

For users requiring access to virtual media, the device permissions
must be set to allow access to the relevant ports, as well as virtual
media access (VM Access port permission) for those ports. Port
permissions are set at the group-level.

A USB connection must exist between the device and the target
server.

If you want to use PC-Share, Security Settings must also be enabled
in the Security Settings page. Optional

You must choose the correct USB profile for the KVM target server
you are connecting to.
Client PC

Certain virtual media options require administrative privileges on the
client PC (for example, drive redirection of complete drives).
Note: If you are using Microsoft Vista or Windows 7, disable User
Account Control or select Run as Administrator when starting
Internet Explorer. To do this, click the Start Menu, locate IE,
right-click and select Run as Administrator.
Target Server

KVM target servers must support USB connected drives.

KVM target servers running Windows 2000 must have all of the
recent patches installed.

USB 2.0 ports are both faster and preferred.
91
Chapter 5: Virtual Media
Using Virtual Media via VKC and AKC in a Windows Environment
Windows XP® operating system Administrator and standard user
privileges vary from those of the Windows Vista® operating system and
the Windows 7® operating system.
When enabled in Vista or Windows 7, User Access Control (UAC) will
provide the lowest level of rights and privileges a user needs for an
application. For example, a Run as Administrator option is provided for
Internet Explorer® form Administrator level tasks, otherwise these will not
be accessible even though the user has an Administrator login.
Both of these features affect the types of virtual media that can be
accessed by users via Virtual KVM Client (VKC) and Active KVM Client
(AKC). See your Microsoft® help for additional information on these
features and how to use them.
Following is a list virtual media types users can access via VKC and AKC
when running in a Windows environment. The features are broken down
by client and the virtual media features that are accessible to each
Windows user role.
Windows XP
 If you are running VKC and AKC in a Windows XP environment,
users must have Administrator privileges to access any virtual media
type other than CD-ROM connections, ISOs and ISO images.
Windows Vista and Windows 7
 If you are running VKC and AKC in a Windows Vista or Windows 7
environment and UAC is enabled, the following virtual media types
can be accessed depending on the Windows role of the user:
Client
Administrator
AKC and Access to:
VKC
 Fixed drives and fixed
drive partitions
92
Standard User
Access to:

Removable drives


CD/DVD drives
Removable drives


ISO images
CD/DVD drives


Remote ISO images
ISO images

Remote ISO images
Chapter 5: Virtual Media
Using Virtual Media
See Prerequisites for Using Virtual Media before proceeding with using
virtual media.
To use virtual media:
1. If you plan to access file server ISO images, identify those file
servers and images through the Remote Console File Server Setup
page. See File Server Setup (File Server ISO Images Only).
Note: ISO9660 format is the standard supported by Raritan.
However, other CD-ROM extensions may also work.
2. Open a KVM session with the appropriate target server.
a. Open the Port Access page from the Remote Console.
b. Connect to the target server from the Port Access page:

Click the Port Name for the appropriate server.

Choose the Connect command from the Port Action menu. The
target server opens in a Virtual KVM Client window.
3. Connect to the virtual media.
For:
Select this VM option:
Local drives
Local Drives
Local CD/DVD drives
CD-ROM/DVD-ROM/ISO Images
ISO Images
Connect CD-ROM/ISO Image
File Server ISO Images
Connect CD-ROM/ISO Image
Upon completion of your tasks, disconnect the virtual media. See
Disconnecting Virtual Media (on page 99).
93
Chapter 5: Virtual Media
File Server Setup (File Server ISO Images Only)
Note: This feature is only required when using virtual media to access file
server ISO images.
ISO9660 format is the standard supported by Raritan. However, other
CD-ROM extensions may also work.
Use the Remote Console File Server Setup page to designate the files
server(s) and image paths that you want to access using virtual media.
File server ISO image(s) specified here will become available for
selection in the Remote Server ISO Image Hostname and Image
drop-down lists in the Map Virtual Media CD/ISO Image dialog. See
CD-ROM/DVD-ROM/ISO Images (on page 97).
To designate file server ISO images for virtual media access:
1. Choose Virtual Media from the Remote Console. The File Server
Setup page opens.
2. Check the Selected checkbox for all media that you want accessible
as virtual media.
3. Enter information about the file server ISO images that you want to
access:

IP Address/Host Name - Host name or IP address of the file
server.

Image Path - Full path name of the location of the ISO image.
Note: The host name cannot exceed 232 characters in length.
4. Click Save. All media specified here will now be available for
selection in the Map Virtual Media CD/ISO Image dialog.
94
Chapter 5: Virtual Media
Note: You cannot access a remote ISO image via virtual media using an
IPv6 address due to technical limitations of third-party software used by
the KX2.
Note: If you are connecting to a Windows 2003 Server and attempt to
load an ISO image from the server, you may receive an error stating
"Virtual Media mounting on port failed. Unable to connect to the file
server or incorrect File Server username and password". If this occurs,
disable the "Microsoft Network Server: Digitally Sign Communications"
option on the server under the Domain Controllers policies.
95
Chapter 5: Virtual Media
Connecting to Virtual Media
Local Drives
This option mounts an entire drive, which means the entire disk drive is
mounted virtually onto the target server. Use this option for hard drives
and external drives only. It does not include network drives, CD-ROM, or
DVD-ROM drives. This is the only option for which Read/Write is
available.
Note: KVM target servers running certain versions of the Windows
operating system may not accept new mass storage connections after an
NTFS-formatted partition (for example, the local C drive) has been
redirected to them.
If this occurs, close the Remote Console and reconnect before
redirecting another virtual media device. If other users are connected to
the same target server, they must also close their connections to the
target server.
Note: In the Dominion KX II 2.1.0 and above, when you mount an
external drive, such as a floppy drive, the LED light on the drive will
remain on because the device is checking the drive every 500
milliseconds to verify the drive is still mounted.
To access a drive on the client computer:
1. From the Virtual KVM Client, choose Virtual Media > Connect Drive.
The Map Virtual Media Drive dialog appears.
2. Choose the drive from the Local Drive drop-down list.
3. If you want Read and Write capabilities, select the Read-Write
checkbox. This option is disabled for nonremovable drives. See the
Conditions when Read/Write is Not Available (on page 97) for
more information. When checked, you will be able to read or write to
the connected USB disk.
96
Chapter 5: Virtual Media
WARNING: Enabling Read/Write access can be dangerous!
Simultaneous access to the same drive from more than one entity
can result in data corruption. If you do not require Write access,
leave this option unselected.
4. Click Connect. The media will be mounted on the target server
virtually. You can access the media just like any other drive.
Conditions when Read/Write is Not Available
Virtual media Read/Write is not available in the following situations:

For all hard drives.

When the drive is write-protected.

When the user does not have Read/Write permission:

Port Permission Access is set to None or View.

Port Permission VM Access is set to Read-Only or Deny.
CD-ROM/DVD-ROM/ISO Images
This option mounts CD-ROM, DVD-ROM, and ISO images.
Note: ISO9660 format is the standard supported by Raritan. However,
other CD-ROM extensions may also work.
To access a CD-ROM, DVD-ROM, or ISO image:
1. From the Virtual KVM Client, choose Virtual Media > Connect
CD-ROM/ISO Image. The Map Virtual Media CD/ISO Image dialog
appears.
97
Chapter 5: Virtual Media
2. For internal and external CD-ROM or DVD-ROM drives:
a. Choose the Local CD/DVD Drive option.
b. Choose the drive from the Local CD/DVD Drive drop-down list.
All available internal and external CD and DVD drive names will
be populated in the drop-down list.
c.
Click Connect.
3. For ISO images:
a. Choose the ISO Image option. Use this option when you want to
access a disk image of a CD, DVD, or hard drive. ISO format is
the only format supported.
b. Click the Browse button.
c.
Navigate to the path containing the disk image you want to use
and click Open. The path is populated in the Image Path field.
d. Click Connect.
4. For remote ISO images on a file server:
a. Choose the Remote Server ISO Image option.
b. Choose Hostname and Image from the drop-down list. The file
servers and image paths available are those that you configured
using the File Server Setup page. Only items you configured
using the File Server Setup page will be in the drop-down list.
c.
File Server Username - User name required for access to the file
server.
d. File Server Password - Password required for access to the file
server (field is masked as you type).
e. Click Connect.
The media will be mounted on the target server virtually. You can
access the media just like any other drive.
Note: If you are working with files on a Linux target, use the Linux Sync
command after the files are copied using virtual media in order to view
the copied files. Files may not appear until a sync is performed.
Note: If you are working with Windows 7, Removable Disk is not
displayed by default in the Window's My Computer folder when you
mount a Local CD/DVD Drive or Local or Remote ISO Image. To view
the Local CD/DVD Drive or Local or Remote ISO Image in this folder,
select Tools > Folder Options > View and deselect "Hide empty drives in
the Computer folder".
Note: You cannot access a remote ISO image via virtual media using an
IPv6 address due to technical limitations of third-party software used by
the KX2.
98
Chapter 5: Virtual Media
Disconnecting Virtual Media
To disconnect the virtual media drives:

For local drives, choose Virtual Media > Disconnect Drive.

For CD-ROM, DVD-ROM, and ISO images, choose Virtual Media >
Disconnect CD-ROM/ISO Image.
Note: In addition to disconnecting the virtual media using the Disconnect
command, simply closing the KVM connection closes the virtual media
as well.
99
Chapter 6
USB Profiles
In This Chapter
Overview ................................................................................................100
CIM Compatibility ..................................................................................101
Available USB Profiles...........................................................................101
Selecting Profiles for a KVM Port ..........................................................107
Overview
To broaden the Dominion KX II's compatibility with different KVM target
servers, Raritan provides a standard selection of USB configuration
profiles for a wide range of operating system and BIOS-level server
implementations.
The Generic (default) USB profile meets the needs of the vast majority of
deployed KVM target server configurations. Additional profiles are
provided to meet the specific needs of other commonly deployed server
configurations (for example, Linux® and Mac OS X®). There are also a
number of profiles (designated by platform name and BIOS revision) to
enhance virtual media function compatibility with the target server, for
example, when operating at the BIOS level.
USB profiles are configured on the Device Settings > Port Configuration
> Port page of the Dominion KX II Remote and Local Consoles. A device
administrator can configure the port with the profiles that best meet the
needs of the user and the target server configuration.
A user connecting to a KVM target server chooses among these
preselected profiles in the Virtual KVM Client (on page 52), depending
on the operational state of the KVM target server. For example, if the
server is running and the user wants to use the Windows® operating
system, it would be best to use the Generic profile. But if the user wants
to change settings in the BIOS menu or boot from a virtual media drive,
depending on the target server model, a BIOS profile may be more
appropriate.
Should none of the standard USB profiles provided by Raritan work with
a given KVM target, please contact Raritan Technical Support for
assistance.
100
Chapter 6: USB Profiles
CIM Compatibility
In order to make use of USB profiles, you must use a D2CIM-VUSB or
D2CIM-DVUSB with updated firmware. A VM-CIM that has not had its
firmware upgraded will support a broad range of configurations
(Keyboard, Mouse, CD-ROM, and Removable Drive) but will not be able
to make use of profiles optimized for particular target configurations.
Given this, existing VM-CIMs should be upgraded with latest firmware in
order to access USB profiles. Until existing VM-CIMs are upgraded, they
will be able to provide functionality equivalent to the „Generic‟ profile.
VM-CIM firmware is automatically upgraded during a Dominion KX II
firmware upgrade, but VM-CIMs that have not had their firmware
upgraded can be upgraded as described in Upgrading CIMs (on page
215).
See Computer Interface Modules (CIMs) (on page 259) for additional
information.
Available USB Profiles
The current release of the Dominion KX II comes with the selection of
USB profiles described in the following table. New profiles are included
with each firmware upgrade provided by Raritan. As new profiles are
added, they will be documented in the help.
USB profile
BIOS Dell® PowerEdge®
1950/2950/2970/6950/R200
Description
Dell PowerEdge
1950/2950/2970/6950/R200 BIOS
Use either this profile or 'Generic'
profile for Dell PowerEdge
1950/2950/2970/6950/R200 BIOS.
Restrictions:

BIOS DellOptiplex Keyboard
Only
None
Dell Optiplex BIOS Access (Keyboard
Only)
Use this profile to have keyboard
functionality for the Dell Optiplex BIOS
when using D2CIM-VUSB. When using
the new D2CIM-DVUSB, use 'Generic'
profile.
Notice:

Optiplex 210L/280/745/GX620
requires D2CIM-DVUSB with
'Generic' profile to support virtual
media
101
Chapter 6: USB Profiles
USB profile
BIOS DellPowerEdge
Keyboard Only
Description
Restrictions:

USB bus speed limited to
full-speed (12 MBit/s)

No virtual media support
Dell PowerEdge BIOS Access
(Keyboard Only)
Use this profile to have keyboard
functionality for the Dell PowerEdge
BIOS when using D2CIM-VUSB. When
using the new D2CIM-DVUSB, use
'Generic' profile.
Notice:

PowerEdge
650/1650/1750/2600/2650 BIOS
do not support USB CD-ROM and
disk drives as a bootable device

PowerEdge
750/850/860/1850/2850/SC1425
BIOS requires D2CIM-DVUSB with
'Generic' profile to support virtual
media

Use 'BIOS Dell PowerEdge
1950/2950/2970/6950/R200' or
'Generic' profile for PowerEdge
1950/2950/2970/6950/R200 when
operating in the BIOS
Restrictions:
BIOS Generic

USB bus speed limited to
full-speed (12 MBit/s)

Absolute mouse synchronization™
not supported

No virtual media support
BIOS Generic
Use this profile when Generic OS
profile does not work on the BIOS.
WARNING: USB enumeration will
trigger whenever virtual media is
connected or disconnected.
Restrictions:
102
Chapter 6: USB Profiles
USB profile
BIOS HP® Proliant™ DL145
Description
 USB bus speed limited to
full-speed (12 MBit/s)

Absolute mouse synchronization™
not supported

Virtual CD-ROM and disk drives
cannot be used simultaneously
HP Proliant DL145 PhoenixBIOS
Use this profile for HP Proliant DL145
PhoenixBIOS during OS installation.
Restrictions:

BIOS HP Compaq®
DC7100/DC7600
USB bus speed limited to
full-speed (12 MBit/s)
BIOS HP Compaq DC7100/DC7600
Use this profile to boot the HP Compaq
DC7100/DC7600 series desktops from
virtual media.
Restrictions:

BIOS IBM ThinkCentre
Lenovo
Virtual CD-ROM and disk drives
cannot be used simultaneously
IBM Thinkcentre Lenovo BIOS
Use this profile for the IBM®
Thinkcentre Lenovo system board
(model 828841U) during BIOS
operations.
Restrictions:
BIOS Lenovo ThinkPad T61
& X61

USB bus speed limited to
full-speed (12 MBit/s)

Virtual CD-ROM and disk drives
cannot be used simultaneously
BIOS Lenovo ThinkPad T61 and X61
(boot from virtual media)
Use this profile to boot the T61 and
X61 series laptops from virtual media.
Restrictions:

BIOS Mac
USB bus speed limited to
full-speed (12 MBit/s)
BIOS Mac
Use this profile for Mac® BIOS.
103
Chapter 6: USB Profiles
USB profile
Generic
Description
Restrictions:

Absolute mouse synchronization™
not supported

Virtual CD-ROM and disk drives
cannot be used simultaneously
The generic USB profile resembles the
behavior of the original KX2 release.
Use this for Windows 2000® operating
system, Windows XP® operating
system, Windows Vista® operating
system and later.
Restrictions:

None
HP Proliant DL360/DL380 G4 HP Proliant DL360/DL380 G4 (HP
(HP SmartStart CD)
SmartStart CD)
Use this profile for the HP Proliant
DL360/DL380 G4 series server when
installing OS using HP SmartStart CD.
Restrictions:

USB bus speed limited to
full-speed (12 MBit/s)

Absolute mouse synchronization™
not supported
HP Proliant DL360/DL380 G4 HP Proliant DL360/DL380 G4
(Windows 2003® Server
(Windows 2003 Server Installation)
Installation)
Use this profile for the HP Proliant
DL360/DL380 G4 series server when
installing Windows 2003 Server
without the help of HP SmartStart CD.
Restrictions:

Linux®
USB bus speed limited to
full-speed (12 MBit/s)
Generic Linux profile
This is the generic Linux profile; use it
for Redhat Enterprise Linux, SuSE
Linux Enterprise Desktop and similar
distributions.
Restrictions:

104
Absolute mouse synchronization™
not supported
Chapter 6: USB Profiles
USB profile
Description
MAC OS X® (10.4.9 and later) Mac OS-X, version 10.4.9 and later
This profile compensates the scaling of
mouse coordinates introduced in
recent versions of Mac OS-X. Select
this if the remote and local mouse
positions get out of sync near the
desktop borders.
Restrictions:

RUBY Industrial Mainboard
(AwardBIOS)
Virtual CD-ROM and disk drives
cannot be used simultaneously
RUBY Industrial Mainboard
(AwardBIOS)
Use this profile for the
RUBY-9715VG2A series industrial
mainboards with Phoenix/AwardBIOS
v6.00PG.
Restrictions:
Supermicro Mainboard
Phoenix (AwardBIOS)

USB bus speed limited to
full-speed (12 MBit/s)

Virtual CD-ROM and disk drives
cannot be used simultaneously
Supermicro Mainboard Phoenix
AwardBIOS
Use this profile for the Supermicro
series mainboards with Phoenix
AwardBIOS.
Restrictions:

Suse 9.2
Virtual CD-ROM and disk drives
cannot be used simultaneously
SuSE Linux 9.2
Use this for SuSE Linux 9.2
distribution.
Restrictions:
Troubleshooting 1

Absolute mouse synchronization™
not supported

USB bus speed limited to
full-speed (12 MBit/s)
Troubleshooting Profile 1

Mass Storage first
105
Chapter 6: USB Profiles
USB profile
Description
 Keyboard and Mouse (Type 1)

USB bus speed limited to
full-speed (12 MBit/s)

Virtual CD-ROM and disk drives
cannot be used simultaneously
WARNING: USB enumeration will
trigger whenever virtual media is
connected or disconnected.
Troubleshooting 2
Troubleshooting Profile 2

Keyboard and Mouse (Type 2) first

Mass Storage

USB bus speed limited to
full-speed (12 MBit/s)

Virtual CD-ROM and disk drives
cannot be used simultaneously
WARNING: USB enumeration will
trigger whenever virtual media is
connected or disconnected.
Troubleshooting 3
Troubleshooting Profile 3

Mass Storage first

Keyboard and Mouse (Type 2)

USB bus speed limited to
full-speed (12 MBit/s)

Virtual CD-ROM and disk drives
cannot be used simultaneously
WARNING: USB enumeration will
trigger whenever virtual media is
connected or disconnected.
Use Full Speed for Virtual
Media CIM
Use Full Speed for virtual media CIM
This profile resembles the behavior of
the original KX2 release with Full
Speed for virtual media CIM option
checked. Useful for BIOS that cannot
handle High Speed USB devices.
Restrictions:

106
USB bus speed limited to
Chapter 6: USB Profiles
USB profile
Description
full-speed (12 MBit/s)
Selecting Profiles for a KVM Port
The Dominion KX II comes with a set of USB profiles that you can assign
to a KVM port based on the characteristics of the KVM target server it
connects to. You assign USB profiles to a KVM port in the Device
Settings > Port Configuration > Port page in either the Dominion KX II
Remote or Local Console.
It is the administrator that designates the profiles that are most likely to
be needed for a specific target. These profiles are then available for
selection via MPC/VKC. If a profile has not been made available, you
can access any of the available profiles by selecting USB Profile > Other
Profiles.
Assigning USB profiles to a KVM port makes those profiles available to a
user when connected to a KVM target server. If required, the user can
select a USB profile from the USB Profile menu in VKC or MPC.
For information about assigning USB profiles to a KVM port, see
Configuring USB Profiles (Port Page) (on page 185).
Mouse Modes when Using the Mac OS-X USB Profile with a
DCIM-VUSB
If you are using a DCIM-VUSB, using a Mac OS-X® USB profile, and
running Mac OS-X 10.4.9 (or later), when you reboot you must be in
Single Mouse mode to use the mouse at the Boot menu.
To configure the mouse to work at the Boot menu:
1. Reboot the Mac and press the Option key during the reboot to open
the Boot menu. The mouse will not respond at this point.
2. Select Intelligent Mouse mode and then select Single Mouse mode.
The mouse will respond.
Note: Mouse speed may be slow while in Single Mouse mode.
3. Once you are out of the Boot menu and have booted to the operating
system, exit Single Mouse mode and switch back to Absolute Mouse
mode for better mouse performance.
107
Chapter 7
User Management
In This Chapter
User Groups ..........................................................................................108
Users .....................................................................................................117
Authentication Settings ..........................................................................120
Changing a Password ...........................................................................131
User Groups
The Dominion KX II stores an internal list of all user and group names to
determine access authorization and permissions. This information is
stored internally in an encrypted format. There are several forms of
authentication and this one is known as local authentication. All users
have to be authenticated. If the Dominion KX II is configured for
LDAP/LDAPS or RADIUS, that authentication is processed first, followed
by local authentication.
Every Dominion KX II is delivered with three default user groups. These
groups cannot be deleted:
User
Admin
Description
Users that are members of this group have full
administrative privileges. The original, factory-default
user is a member of this group and has the complete
set of system privileges. In addition, the Admin user
must be a member of the Admin group.
Unknown
This is the default group for users who are
authenticated externally using LDAP/LDAPS or
RADIUS or who are unknown to the system. If the
external LDAP/LDAPS or RADIUS server does not
identify a valid user group, the Unknown group is
used. In addition, any newly created user is
automatically put in this group until assigned to
another group.
Individual
Group
An individual group is essentially a “group” of one.
That is, the specific user is in its own group, not
affiliated with other real groups. Individual groups can
be identified by the “@” in the Group Name. The
individual group allows a user account to have the
same rights as a group.
Up to 254 user groups can be created in the Dominion KX II.
108
Chapter 7: User Management
User Group List
User groups are used with local and remote authentication (via RADIUS
or LDAP/LDAPS). It is a good idea to define user groups before creating
individual users since, when you add a user, you must assign that user
to an existing user group.
The User Group List page displays a list of all user groups, which can be
sorted in ascending or descending order by clicking on the Group Name
column heading. From the User Group List page, you can also add,
modify, or delete user groups.
To list the user groups:

Choose User Management > User Group List. The User Group List
page opens.
Relationship Between Users and Groups
Users belong to a group and groups have privileges. Organizing the
various users of your Dominion KX II into groups saves time by allowing
you to manage permissions for all users in a group at once, instead of
managing permissions on a user-by-user basis.
You may also choose not to associate specific users with groups. In this
case, you can classify the user as “Individual.”
Upon successful authentication, the device uses group information to
determine the user's permissions, such as which server ports are
accessible, whether rebooting the device is allowed, and other features.
Adding a New User Group
To add a new user group:
1. Open the Group page by selecting User Management > Add New
User Group or clicking the Add button from the User Group List
page.
109
Chapter 7: User Management
The Group page is organized into the following categories: Group,
Permissions, Port Permissions, and IP ACL.
2. Type a descriptive name for the new user group into the Group
Name field (up to 64 characters).
3. Set the permissions for the group. Select the checkboxes before the
permissions you want to assign to all of the users belonging to this
group. See Setting Permissions (on page 112).
4. Set the port permissions. Specify the server ports that can be
accessed by users belonging to this group (and the type of access).
See Setting Port Permissions (on page 113).
5. Set the IP ACL. This feature limits access to the Dominion KX II
device by specifying IP addresses. It applies only to users belonging
to a specific group, unlike the IP Access Control list feature that
applies to all access attempts to the device (and takes priority).
Optional. See Group-Based IP ACL (Access Control List) (on
page 114).
6. Click OK.
110
Chapter 7: User Management
Note: Several administrative functions are available within MPC and from
the Dominion KX II Local Console. These functions are available only to
members of the default Admin group.
Note: Both IPv4 and IPv6 addresses are supported.
111
Chapter 7: User Management
Setting Permissions
Important: Selecting the User Management checkbox allows the
members of the group to change the permissions of all users,
including their own. Carefully consider granting these permissions.
Permission
Description
Device Access
While Under
CC-SG
Management
Allows users and user groups with this
permission to directly access the Dominion KX
II using an IP address when Local Access is
enabled for the device in CC-SG. The device
can be accessed from the Local Console,
Remote Console, MPC, VKC, and AKC.
When a device is accessed directly while it is
under CC-SG management, access and
connection activity is logged on the Dominion
KX II. User authentication is performed based
on Dominion KX II authentication settings.
Note: The Admin user group has this
permission by default.
Device Settings
Network settings, date/time settings, port
configuration (channel names, power
associations), event management (SNMP,
Syslog), virtual media file server setups.
Diagnostics
Network interface status, network statistics,
ping host, trace route to host, Dominion KX II
diagnostics.
Maintenance
Backup and restore database, firmware
upgrade, factory reset, reboot.
Modem Access
Permission to use the modem to connect to the
Dominion KX II device.
PC-Share
Simultaneous access to the same target by
multiple users.
If you are using a tiered configuration in which
a base Dominion KX II device is used to access
multiple other tiered devices, all devices must
share the same PC-Share setting. See
Configuring and Enabling Tiering (on page
139) for more information on tiering.
Security
112
SSL certificate, security settings (VM Share,
PC-Share), IP ACL.
Chapter 7: User Management
Permission
Description
User
Management
User and group management, remote.
authentication (LDAP/LDAPS/RADIUS), login
settings.
If you are using a tiered configuration in which
a base Dominion KX II device is used to access
multiple other tiered devices, user, user group
and remote authentication settings must be
consistent across all devices. See Configuring
and Enabling Tiering (on page 139) for more
information on tiering.
Setting Port Permissions
For each server port, you can specify the access type the group has, as
well as the type of port access to the virtual media and the power control.
Please note that the default setting for all permissions is Deny.
Port access
Option
Description
Deny
Denied access completely
View
View the video (but not interact with) the connected
target server
Control
Control the connected target server. Control must be
assigned to the group if VM and power control access
will also be granted.
VM access
Option
Description
Deny
Virtual media permission is denied altogether for the
port
Read-Only
Virtual media access is limited to read access only
Read-Write
Complete access (read, write) to virtual media
113
Chapter 7: User Management
Power control access
Option
Description
Deny
Deny power control to the target server
Access
Full permission to power control on a target server
For blade chassis, the port access permission will control access to the
URLs that have been configured for that blade chassis. The options are
Deny or Control. In addition, each blade housed within the chassis has
its own independent Port Permissions setting.
If you are using a tiered configuration in which a base Dominion KX II
device is used to access multiple other tiered devices, the tiered device
enforces individual port control levels. See Configuring and Enabling
Tiering (on page 139) for more information on tiering.
Setting Permissions for an Individual Group
To set permissions for an individual user group:
1. Locate the group from among the groups listed. Individual groups
can be identified by the @ in the Group Name.
2. Click the Group Name. The Group page opens.
3. Select the appropriate permissions.
4. Click OK.
Note: See Alternate RADIUS Authentication Settings for information on
additional settings if you are using Alternate RADIUS Authentication.
Group-Based IP ACL (Access Control List)
Important: Exercise caution when using group-based IP access
control. It is possible to be locked out of your Dominion KX II if your
IP address is within a range that has been denied access.
This feature limits access to the Dominion KX II device by users in the
selected group to specific IP addresses. This feature applies only to
users belonging to a specific group, unlike the IP Access Control List
feature that applies to all access attempts to the device, is processed
first, and takes priority.
Important: The IP address 127.0.0.1 is used by the Dominion KX II
Local Port and cannot be blocked.
114
Chapter 7: User Management
Use the IP ACL section of the Group page to add, insert, replace, and
delete IP access control rules on a group-level basis.
To add (append) rules:
1. Type the starting IP address in the Starting IP field.
2. Type the ending IP address in the Ending IP field.
3. Choose the action from the available options:

Accept - IP addresses set to Accept are allowed access to the
Dominion KX II device.

Drop - IP addresses set to Drop are denied access to the
Dominion KX II device.
4. Click Append. The rule is added to the bottom of the rules list.
Repeat steps 1 through 4 for each rule you want to enter.
To insert a rule:
1. Enter a rule number (#). A rule number is required when using the
Insert command.
2. Enter the Starting IP and Ending IP fields.
3. Choose the action from the Action drop-down list.
4. Click Insert. If the rule number you just typed equals an existing rule
number, the new rule is placed ahead of the exiting rule and all rules
are moved down in the list.
To replace a rule:
1. Specify the rule number you want to replace.
2. Type the Starting IP and Ending IP fields.
3. Choose the Action from the drop-down list.
4. Click Replace. Your new rule replaces the original rule with the same
rule number.
To delete a rule:
1. Specify the rule number you want to delete.
115
Chapter 7: User Management
2. Click Delete.
3. When prompted to confirm the deletion, click OK.
Important: ACL rules are evaluated in the order in which they are
listed. For instance, in the example shown here, if the two ACL
rules were reversed, Dominion would accept no communication at
all.
Tip: The rule numbers allow you to have more control over the order in
which the rules are created.
Note: Both IPv4 and IPv6 addresses are supported.
Modifying an Existing User Group
Note: All permissions are enabled (and cannot be changed) for the
Admin group.
To modify an existing user group:
1. From the Group page, change the appropriate fields and set the
appropriate permissions.
2. Set the Permissions for the group. Select the checkboxes before the
permissions you want to assign to all of the users belonging to this
group. See Setting Permissions.
3. Set the Port Permissions. Specify the server ports that can be
accessed by users belonging to this group (and the type of access).
See Setting Port Permissions (on page 113).
4. Set the IP ACL (optional). This feature limits access to the Dominion
KX II device by specifying IP addresses. See Group-Based IP ACL
(Access Control List) (on page 114).
5. Click OK.
To delete a user group:
Important: If you delete a group with users in it, the users are
automatically assigned to the <unknown> user group.
116
Chapter 7: User Management
Tip: To determine the users belonging to a particular group, sort the User
List by User Group.
1. Choose a group from among those listed by checking the checkbox
to the left of the Group Name.
2. Click Delete.
3. When prompted to confirm the deletion, click OK.
Users
Users must be granted user names and passwords to gain access to the
Dominion KX II. This information is used to authenticate users attempting
to access your Dominion KX II. Up to 254 users can be created for each
user group.
If you are using a tiered configuration in which a base Dominion KX II
device is used to access multiple other tiered devices, users will need
permission to access the base device and permissions to access each
individual tiered device (as needed). When users log on to the base
device, each tiered device is queried and the user can access each
target server they have permissions to. See Configuring and Enabling
Tiering (on page 139) for more information on tiering.
User List
The User List page displays a list of all users including their user name,
full name, and user group. The list can be sorted on any of the columns
by clicking on the column name. From the User List page, you can also
add, modify, or delete users.
To view the list of users:

Choose User Management > User List. The User List page opens.
117
Chapter 7: User Management
Adding a New User
It is a good idea to define user groups before creating Dominion KX II
users because, when you add a user, you must assign that user to an
existing user group. See Adding a New User Group (on page 109).
From the User page, you can add new users, modify user information,
and reactivate users that have been deactivated.
Note: A user name can be deactivated when the number of failed login
attempts has exceeded the maximum login attempts set in the Security
Settings page. See Security Settings.
To add a new user:
1. Open the User page by choosing User Management > Add New
User or clicking the Add button on the User List page.
2. Type a unique name in the Username field (up to 16 characters).
3. Type the person's full name in the Full Name field (up to 64
characters).
4. Type a password in the Password field and retype the password in
the Confirm Password field (up to 64 characters).
5. Choose the group from the User Group drop-down list. The list
contains all groups you have created in addition to the
system-supplied default groups. <Unknown>, which is the default
setting, Admin, Individual Group.
If you do not want to associate this user with an existing User Group,
select Individual Group from the drop-down list. For more information
about permissions for an Individual Group, see Setting Permissions
for an Individual Group (on page 114).
6. To activate the new user, select the Active checkbox. The default is
activated (enabled).
7. Click OK.
Modifying an Existing User
To modify an existing user:
1. Open the User List page by choosing User Management > User List.
2. Locate the user from among those listed on the User List page.
3. Click the user name. The User page opens.
4. On the User page, change the appropriate fields. See Adding a New
User (on page 118) for information about how to get access the User
page.
118
Chapter 7: User Management
5. To delete a user, click Delete. You are prompted to confirm the
deletion.
6. Click OK.
Logging a User Off (Force Logoff)
If you are an administrator, you are able to log out another locally
authenticated user who is logged on to the Dominion KX II.
To log out a user:
1. Open the User List page by choosing User Management > User List
or click the Connected User link in the left panel of the page.
2. Locate the user from among those listed on the User List page and
select the checkbox next to their name.
3. Click the Force User Logoff button.
4. Click OK on the Logoff User dialog to forcefully log the user off.
5. A confirmation message will then be displayed to indicate that the
user was logged off. This message contains the date and time the
log out occurred. Click OK to close the message.
119
Chapter 7: User Management
Authentication Settings
Authentication is the process of verifying that a user is who he says he
is. Once a user is authenticated, the user's group is used to determine
his system and port permissions. The user's assigned privileges
determine what type of access is allowed. This is called authorization.
When the Dominion KX II is configured for remote authentication, the
external authentication server is used primarily for the purposes of
authentication, not authorization.
If you are using a tiered configuration in which a base Dominion KX II
device is used to access multiple other tiered devices, the base device
and the tiered devices must using the same authentication settings.
From the Authentication Settings page you can configure the type of
authentication used for access to your Dominion KX II.
Note: When remote authentication (LDAP/LDAPS or RADIUS) is
selected, if the user is not found, the local authentication database will
also be checked.
To configure authentication:
1. Choose User Management > Authentication Settings. The
Authentication Settings page opens.
2. Choose the option for the authentication protocol you want to use
(Local Authentication, LDAP/LDAPS, or RADIUS). Choosing the
LDAP option enables the remaining LDAP fields; selecting the
RADIUS option enables the remaining RADIUS fields.
3. If you choose Local Authentication, proceed to step 6.
4. If you choose LDAP/LDAPS, read the section entitled Implementing
LDAP Remote Authentication for information about completing the
fields in the LDAP section of the Authentication Settings page.
5. If you choose RADIUS, read the section entitled Implementing
RADIUS Remote Authentication for information about completing the
fields in the RADIUS section of the Authentication Settings page.
6. Click OK to save.
To return to factory defaults:

120
Click the Reset to Defaults button.
Chapter 7: User Management
Implementing LDAP/LDAPS Remote Authentication
Lightweight Directory Access Protocol (LDAP/LDAPS) is a networking
protocol for querying and modifying directory services running over
TCP/IP. A client starts an LDAP session by connecting to an
LDAP/LDAPS server (the default TCP port is 389). The client then sends
operation requests to the server, and the server sends responses in turn.
Reminder: Microsoft Active Directory functions natively as an
LDAP/LDAPS authentication server.
To use the LDAP authentication protocol:
1. Click User Management > Authentication Settings to open the
Authentication Settings page.
2. Select the LDAP radio button to enable the LDAP section of the
page.
3. Click the
icon to expand the LDAP section of the page.
Server Configuration
4. In the Primary LDAP Server field, type the IP address or DNS name
of your LDAP/LDAPS remote authentication server (up to 256
characters). When the Enable Secure LDAP option is selected and
the Enable LDAPS Server Certificate Validation option is selected,
the DNS name must be used to match the CN of LDAP server
certificate.
5. In the Secondary LDAP Server field, type the IP address or DNS
name of your backup LDAP/LDAPS server (up to 256 characters).
When the Enable Secure LDAP option is selected, the DNS name
must be used. Note that the remaining fields share the same settings
with the Primary LDAP Server field. Optional
6. Type of External LDAP Server.
7. Type the name of the Active Directory Domain. For example,
testradius.com. Consult your Active Directive Administrator for a
specific domain name.
8. In the User Search DN field, enter the Distinguished Name of where
in the LDAP database you want to begin searching for user
information. Up to 64 characters can be used. An example base
search value might be: cn=Users,dc=raritan,dc=com. Consult
your authentication server administrator for the appropriate values to
enter into these fields.
121
Chapter 7: User Management
9. Enter the Distinguished Name of the Administrative User in the DN of
Administrative User field (up to 64 characters). Complete this field if
your LDAP server only allows administrators to search user
information using the Administrative User role. Consult your
authentication server administrator for the appropriate values to type
into this field. An example DN of Administrative User value might be:
cn=Administrator,cn=Users,dc=testradius,dc=com.
Optional
10. If you entered a Distinguished Name for the Administrative User, you
must enter the password that will be used to authenticate the
Administrative User's DN against the remote authentication server.
Enter the password in the Secret Phrase field and again in the
Confirm Secret Phrase field (up to 128 characters).
LDAP/Secure LDAP
122
Chapter 7: User Management
11. Select the Enable Secure LDAP checkbox if you would like to use
SSL. This will enable the Enable LDAPS Server Certificate Validation
checkbox. Secure Sockets Layer (SSL) is a cryptographic protocol
that allows Dominion KX II to communicate securely with the
LDAP/LDAPS server.
12. The default Port is 389. Either use the standard LDAP TCP port or
specify another port.
13. The default Secure LDAP Port is 636. Either use the default port or
specify another port. This field is only used when the Enable Secure
LDAP checkbox is selected.
14. Select the Enable LDAPS Server Certificate Validation checkbox to
use the previously uploaded root CA certificate file to validate the
certificate provided by the server. If you do not want to use the
previously uploaded root CA certificate file, leave this checkbox
deselected. Disabling this function is the equivalent of accepting a
certificate that has been signed by an unknown certifying authority.
This checkbox is only available when the Enable Secure LDAP
checkbox has been enabled.
Note: When the Enable LDAPS Server Certificate Validation option is
selected, in addition to using the Root CA certificate for validation,
the server hostname must match the common name provided in the
server certificate.
123
Chapter 7: User Management
15. If needed, upload the Root CA Certificate File. This field is enabled
when the Enable Secure LDAP option is selected. Consult your
authentication server administrator to get the CA certificate file in
Base64 encoded X-509 format for the LDAP/LDAPS server. Use the
Browse button to navigate to the certificate file. If you are replacing a
certificate for the LDAP/LDAPS server with a new certificate, you
must reboot the Dominion KX II in order for the new certificate to
take effect.
Test LDAP Server Access
16. The Dominion KX II provides you with the ability to test the LDAP
configuration from the Authentication Settings page due to the
complexity sometimes encountered with successfully configuring the
LDAP server and Dominion KX II for remote authentication. To test
the LDAP configuration, enter the login name and password in the
"Login for testing" field and the "Password for testing" field
respectively. This is the username and password you entered to
access the Dominion KX II and that the LDAP server will use to
authenticate you. Click Test.
124
Chapter 7: User Management
Once the test is completed, a message will be displayed that lets you
know the test was successful or, if the test failed, a detailed error
message will be displayed. It will display successful result or detail
error message in failure case. It also can display group information
retrieved from remote LDAP server for the test user in case of
success.
Returning User Group Information from Active Directory Server
The Dominion KX II supports user authentication to Active Directory®
(AD) without requiring that users be defined locally on the Dominion KX
II. This allows Active Directory user accounts and passwords to be
maintained exclusively on the AD server. Authorization and AD user
privileges are controlled and administered through the standard
Dominion KX II policies and user group privileges that are applied locally
to AD user groups.
IMPORTANT: If you are an existing Raritan, Inc. customer, and have
already configured the Active Directory server by changing the AD
schema, the Dominion KX II still supports this configuration and
you do not need to perform the following operations. See Updating
the LDAP Schema for information about updating the AD
LDAP/LDAPS schema.
To enable your AD server on the Dominion KX II:
1. Using the Dominion KX II, create special groups and assign proper
permissions and privileges to these groups. For example, create
groups such as KVM_Admin and KVM_Operator.
2. On your Active Directory server, create new groups with the same
group names as in the previous step.
3. On your AD server, assign the Dominion KX II users to the groups
created in step 2.
4. From the Dominion KX II, enable and configure your AD server
properly. See Implementing LDAP/LDAPS Remote Authentication.
Important Notes:
125
Chapter 7: User Management

Group Name is case sensitive.

The Dominion KX II provides the following default groups that cannot
be changed or deleted: Admin and <Unknown>. Verify that your
Active Directory server does not use the same group names.

If the group information returned from the Active Directory server
does not match a Dominion KX II group configuration, the Dominion
KX II automatically assigns the group of <Unknown> to users who
authenticate successfully.

If you use a dialback number, you must enter the following
case-sensitive string: msRADIUSCallbackNumber.

Based on recommendations from Microsoft, Global Groups with user
accounts should be used, not Domain Local Groups.
Implementing RADIUS Remote Authentication
Remote Authentication Dial-in User Service (RADIUS) is an AAA
(authentication, authorization, and accounting) protocol for network
access applications.
To use the RADIUS authentication protocol:
1. Click User Management > Authentication Settings to open the
Authentication Settings page.
2. Click the RADIUS radio button to enable the RADIUS section of the
page.
3. Click the
page.
icon to expand the RADIUS section of the
4. In the Primary Radius Server and Secondary Radius Server fields,
type the IP address of your primary and optional secondary remote
authentication servers, respectively (up to 256 characters).
5. In the Shared Secret fields, type the server secret used for
authentication (up to 128 characters).
The shared secret is a character string that must be known by both
the Dominion KX II and the RADIUS server to allow them to
communicate securely. It is essentially a password.
6. The Authentication Port default is port is 1812 but can be changed
as required.
7. The Accounting Port default port is 1813 but can be changed as
required.
8. The Timeout is recorded in seconds and default timeout is 1 second,
but can be changed as required.
The timeout is the length of time the Dominion KX II waits for a
response from the RADIUS server before sending another
authentication request.
126
Chapter 7: User Management
9. The default number of retries is 3 Retries.
This is the number of times the Dominion KX II will send an
authentication request to the RADIUS server.
10. Choose the Global Authentication Type from among the options in
the drop-down list:

PAP - With PAP, passwords are sent as plain text. PAP is not
interactive. The user name and password are sent as one data
package once a connection is established, rather than the server
sending a login prompt and waiting for a response.

CHAP - With CHAP, authentication can be requested by the
server at any time. CHAP provides more security than PAP.
127
Chapter 7: User Management
Note: Both IPv4 and IPv6 addresses are supported.
Returning User Group Information via RADIUS
When a RADIUS authentication attempt succeeds, the Dominion KX II
determines the permissions for a given user based on the permissions of
the user's group.
Your remote RADIUS server can provide these user group names by
returning an attribute, implemented as a RADIUS FILTER-ID. The
FILTER-ID should be formatted as follows: Raritan:G{GROUP_NAME}
where GROUP_NAME is a string denoting the name of the group to
which the user belongs.
Raritan:G{GROUP_NAME}:D{Dial Back Number}
where GROUP_NAME is a string denoting the name of the group to
which the user belongs and Dial Back Number is the number associated
with the user account that the Dominion KX II modem will use to dial
back to the user account.
RADIUS Communication Exchange Specifications
The Dominion KX II sends the following RADIUS attributes to your
RADIUS server:
Attribute
Data
Log in
Access-Request (1)
NAS-Port-Type (61)
VIRTUAL (5) for network connections.
NAS-IP-Address (4)
The IP address for the Dominion KX II.
User-Name (1)
The user name entered at the login screen.
Acct-Session-ID (44)
Session ID for accounting.
User-Password(2)
The encrypted password.
Accounting-Request(4)
128
Acct-Status (40)
Start(1) - Starts the accounting.
NAS-Port-Type (61)
VIRTUAL (5) for network connections.
NAS-Port (5)
Always 0.
NAS-IP-Address (4)
The IP address for the Dominion KX II.
User-Name (1)
The user name entered at the login screen.
Chapter 7: User Management
Attribute
Data
Log in
Acct-Session-ID (44)
Session ID for accounting.
Log out
Accounting-Request(4)
Acct-Status (40)
Stop(2) - Stops the accounting
NAS-Port-Type (61)
VIRTUAL (5) for network connections.
NAS-Port (5)
Always 0.
NAS-IP-Address (4)
The IP address for the Dominion KX II.
User-Name (1)
The user name entered at the login screen.
Acct-Session-ID (44)
Session ID for accounting.
129
Chapter 7: User Management
User Authentication Process
Remote authentication follows the process specified in the flowchart
below:
130
Chapter 7: User Management
Changing a Password
To change your password:
1. Choose User Management > Change Password. The Change
Password page opens.
2. Type your current password in the Old Password field.
3. Type a new password in the New Password field. Retype the new
password in the Confirm New Password field. Passwords can be up
to 64 characters in length and can consist of English alphanumeric
characters and special characters.
4. Click OK.
5. You will receive confirmation that the password was successfully
changed. Click OK.
Note: If strong passwords are in use, this page displays information
about the format required for the passwords. For more information about
passwords and strong passwords, see Strong Passwords (on page
195).
131
Chapter 8
Device Management
In This Chapter
Network Settings ...................................................................................132
Device Services .....................................................................................137
Configuring Modem Settings .................................................................145
Configuring Date/Time Settings ............................................................146
Event Management ...............................................................................148
Power Supply Setup ..............................................................................154
Configuring Ports ...................................................................................156
Network Settings
Use the Network Settings page to customize the network configuration
(for example, the IP address, discovery port, and LAN interface
parameters) for your Dominion KX II.
There are two options available to set up your IP configuration:

None (default) - This is the recommended option (static IP). Since
the Dominion KX II is part of your network infrastructure, you most
likely do not want its IP address to change frequently. This option
allows you to set the network parameters.

DHCP - With this option, the IP address is automatically assigned by
a DHCP server.
To change the network configuration:
1. Choose Device Settings > Network. The Network Settings page
opens.
2. Update the Network Basic Settings. See Network Basic Settings.
3. Update the LAN Interface Settings. See LAN Interface Settings.
4. Click OK to set these configurations. If your changes require
rebooting the device, a reboot message appears.
To reset to factory defaults:

Click Reset to Defaults.
Note: Both IPv4 and IPv6 addresses are supported.
132
Chapter 8: Device Management
Network Basic Settings
These procedures describe how to assign an IP address on the Network
Settings page. For complete information about all of the fields and the
operation of this page, see Network Settings (on page 132).
1. Choose Device Settings > Network. The Network Settings page
opens.
2. Specify a meaningful Device Name for your Dominion KX II device.
Up to 32 alphanumeric characters using valid special characters and
no spaces.
3. In the IPv4 section, enter or select the appropriate IPv4-specific
network settings:
a. Enter the IP Address if needed. The default IP address is
192.168.0.192.
b. Enter the Subnet Mask. The default subnet mask is
255.255.255.0.
c.
Enter the Default Gateway if None is selected from the IP Auto
Configuration drop-down.
d. Enter the Preferred DHCP Host Name if DHCP is selected from
the IP Auto Configuration drop-down.
e. Select the IP Auto Configuration. The following options are
available:

None (Static IP) - This option requires that you manually specify
the network parameters.
This is the recommended option because the Dominion KX II is
an infrastructure device and its IP address should not change.

DHCP - Dynamic Host Configuration Protocol is used by
networked computers (clients) to obtain unique IP addresses
and other parameters from a DHCP server.
With this option, network parameters are assigned by the DHCP
server. If DHCP is used, enter the Preferred host name (DHCP
only). Up to 63 characters.
4. If IPv6 is to be used, enter or select the appropriate IPv6-specific
network settings in the IPv6 section:
a. Select the IPv6 checkbox to active the fields in the section.
b. Enter a Global/Unique IP Address. This is the IP address
assigned to the Dominion KX II.
c.
Enter the Prefix Length. This is the number of bits used in the
IPv6 address.
d. Enter the Gateway IP Address.
133
Chapter 8: Device Management
e. Link-Local IP Address. This address is automatically assigned to
the device. It is used for neighbor discovery or when no routers
are present. Read-Only
f.
Zone ID. This identifies the device with which the address is
associated. Read-Only
g. Select the IP Auto Configuration. The following options are
available:

None - Use this option if you do not want an auto IP configuration
and prefer to set the IP address yourself (static IP). This is the
default and recommended option.
If None is selected for the IP auto configuration, the following
Network Basic Settings fields are enabled: Global/Unique IP
Address, Prefix Length, and Gateway IP Address allowing you to
manually set the IP configuration.

Router Discovery - Use this option to automatically assign IPv6
addresses that have Global or Unique Local significance beyond
that of the Link Local, which only applies to a directly connected
subnet.
5. Select Obtain DNS Server Address Automatically if DHCP is
selected and Obtain DNS Server Address is enabled. When Obtain
DNS Server Address Automatically, the DNS information provided by
the DHCP server will be used.
6. If Use the Following DNS Server Addresses is selected, regardless
of whether DHCP is selected or not, the addresses entered in this
section will be used to connect to the DNS server.
Enter the following information if the Following DNS Server
Addresses option is selected. These addresses are the primary and
secondary DNS addresses that will be used if the primary DNS
server connection is lost due to an outage.
a. Primary DNS Server IP Address
b. Secondary DNS Server IP Address
7. When finished, click OK. Your Dominion KX II device is now network
accessible.
134
Chapter 8: Device Management
See LAN Interface Settings (on page 135) for information in configuring
this section of the Network Settings page.
Note: In some environments, the default LAN Interface Speed & Duplex
setting Autodetect (autonegotiator) does not properly set the network
parameters, which results in network issues. In these instances, setting
the Dominion KX II LAN Interface Speed & Duplex field to 100 Mbps/Full
Duplex (or whatever option is appropriate to your network) addresses the
issue. See the Network Settings (on page 132) page for more
information.
LAN Interface Settings
1. The current parameter settings are identified in the Current LAN
interface parameters field.
2. Choose the LAN Interface Speed & Duplex from the following
options:
135
Chapter 8: Device Management

Autodetect (default option)

10 Mbps/Half - Both LEDs blink

10 Mbps/Full - Both LEDs blink

100 Mbps/Half - Yellow LED blinks

100 Mbps/Full - Yellow LED blinks

1000 Mbps/Full (gigabit) - Green LED blinks

Half-duplex provides for communication in both directions, but
only one direction at a time (not simultaneously).

Full-duplex allows communication in both directions
simultaneously.
Note: Occasionally there are problems running at 10 Mbps in either
half or full duplex. If you are experiencing problems, try another
speed and duplex setting.
See Network Speed Settings (on page 281) for more information.
3. Select the Enable Automatic Failover checkbox to allow the
Dominion KX II to automatically recover its network connection using
a second network port if the active network port fails.
Note: Because a failover port is not activated until after a failover has
actually occurred, Raritan recommends that you not monitor the port
or monitor it only after a failover occurs.
When this option is enabled, the following two fields are used:

Ping Interval (seconds) - Ping interval determines how often the
Dominion KX II checks the status of the network path to the
designated gateway. The default ping interval is 30 seconds.

Timeout (seconds) - Timeout determines how long a designated
gateway remains unreachable via the network connection before
a fail over occurs.
Note: The ping interval and timeout can be configured to best meet
the local network conditions. The timeout should be set to allow for at
least two or more ping requests to be transmitted and responses
returned. For example, if a high rate of failover is observed due to
high network utilization, the timeout should be extended to 3 or 4
times the ping interval.
4. Select the Bandwidth from the following options:
136

100 Megabit

10 Megabit

5 Megabit

2 Megabit
Chapter 8: Device Management

512 Kilobit

256 Kilobit

128 Kilobit
5. Click OK to apply the LAN settings.
Device Services
The Device Services page allows you to configure the following
functions:

Enable SSH access.

Enable tiering for the base Dominion KX II.

Enter the discovery port.

Enable direct port access.

Enable the AKC Download Server Certificate Validation feature if you
are using AKC.
137
Chapter 8: Device Management
Enabling SSH
Enable SSH access to allow administrators to access the Dominion KX II
via the SSH v2 application.
To enable SSH access:
1. Choose Device Settings > Device Services. The Device Service
Settings page appears.
2. Select Enable SSH Access.
3. Enter the SSH Port information. The standard SSH TCP port number
is 22 but the port number can be changed to provide a higher level of
security operations.
4. Click OK.
HTTP and HTTPS Port Settings
You are now able to configure HTTP and/or HTTPS ports used by the
Dominion KX II. For example, if you are using the default HTTP port 80
for another purpose, changing the port will ensure the Dominion KX II
does not attempt to use it.
To change the HTTP and/or HTTPS port settings:
1. Choose Device Settings > Device Services. The Device Service
Settings page appears.
2. Enter the new ports in the HTTP Port and/or HTTPS Port fields.
3. Click OK.
Entering the Discovery Port
The Dominion KX II discovery occurs over a single, configurable TCP
Port. The default is Port 5000, but you can configure it to use any TCP
port except 80 and 443. To access the Dominion KX II from beyond a
firewall, your firewall settings must enable two-way communication
through the default Port 5000 or a non-default port configured here.
To enable the discovery port:
1. Choose Device Settings > Device Services. The Device Service
Settings page appears.
2. Enter the Discovery Port.
3. Click OK.
138
Chapter 8: Device Management
Configuring and Enabling Tiering
The tiering feature allows you to access Dominion KX II targets and
PDUs through one base Dominion KX II device. This feature is available
for standard Dominion KX II devices as well as KX2-832 and KX2-864
devices. Devices can be added and removed from a configuration as
needed up to a maximum of two tiered levels.
When setting up the devices, you will use specific CIMS for specific
configurations. See Tiering - Target Types, Supported CIMS and
Tiering Configurations (on page 141) for a description of the targets
that can be included in a tiered configuration, CIM compatibility and
device configuration information.
Before adding tiered devices, you must enable tiering for the base device
and the tiered devices. Enable base devices on the Device Settings
page. Enable tiered devices on the Local Port Settings page. Once
devices are enabled and configured, they appear on the Port Access
page (Port Access Page (on page 42)).
When a Dominion KX II is configured to function as a base device or
tiered device, they will be displayed as:

Configured As Base Device in the Device Information section of the
left panel of the Dominion KX II interface for base devices.

Configured As Tier Device in the Device Information section of the
left panel of the Dominion KX II interface for tiered devices.

The base device will be identified as Base in the left panel of the
tiered device's interface under Connect User.

Target connections to a tier port from the base will be displayed as 2
ports connected.
The base device provides remote and local access over a consolidated
port list from the Port Access page. Tiered devices provide remote
access from their own port lists. Local access is not available on the
tiered devices when Tiering is enabled.
Tiering also supports the use of KVM switches to switch between
servers. See Configuring KVM Switches (on page 158).
139
Chapter 8: Device Management
Enabling Tiering
Connect from a target server port on the base device to the tier Dominion
KX II Local Access port video/keyboard/mouse ports using a
D2CIM-DVUSB.
If the tier device is a KX2-832 or KX2-864, connect from a target server
port on the base device directly to the tier KX2-832/KX2-864 Extended
Local port.
To enable tiering:
1. From the tier base, choose Device Settings > Device Services. The
Device Service Settings page appears.
2. Select Enable Tiering as Base.
3. In the Base Secret field, enter the secret shared between the base
and the tiered devices. This secret is required for the tiered devices
to authenticate the base device. You will enter the same secret word
for the tiered device.
4. Click OK.
5. Enable the tiered devices. From the tiered device, choose Device
Settings > Local Port Settings.
6. In the Enable Local Ports section of the page, select Enable Local
Port Device Tiering.
7. In the Tier Secret field, enter the same secret word you entered for
the base device on the Device Settings page.
8. Click OK.
140
Chapter 8: Device Management
Tiering - Target Types, Supported CIMS and Tiering Configurations
Blade Chassis
Blade chassis that attached directly to the base are accessible.
Power Control
You can power on and off targets that are a part of the tiered
configuration. These targets are accessed from the Port Access page.
Dominion KX II PDU outlets can be accessed and controlled via a tiered
configuration with either the Dominion KX II or KXII-832 and KXII-864
models. If targets and outlets are associated, power control is available
from the Port Access page. Targets and PDU outlet associations are
limited to those attached to the same Dominion KX II.
PDUs attached to the base or tiered Dominion KX IIs are displayed on
the Power page drop-down along with the statistics for the selected
powerstrip.
Outlet level control is available as well. Specifically, you can power off
and power on outlets that are currently on, but you cannot power cycle
outlets that are currently off.
Dominion KX II to Dominion KX II or KXII-8xx Local Port
Configuration - Compatible CIMS
The following CIMS are compatible when you are configuring a base
Dominion KX II to access and control either additional Dominion KX II or
KXII-832 and KXII-864 models, as well as Dominion KX II PDUs and
blade chassis.
If you are using a Dominion KX II to Dominion KX II configuration, the
D2CIM-DVUSB must be used. If you are using a Dominion KX II to
KXII-8xx configuration, only the extended local port can be used.
If you are using a configuration that consists of a Dominion KX II and
KXII-832 or KXII-864, each device must be running the same firmware.
Where blade chassis are a part of a configuration, each blade chassis
counts as one target port.
Unsupported and Limited Features on Tiered Targets
The following features are not supported on tiered targets:

Blade chassis on tiered devices

Smartcards on tiered devices

Virtual media tiered devices

MCCAT as a tiered device
Port group management is limited to creating port groups of members
directly attached to the base.
141
Chapter 8: Device Management
Cabling Example in Tiered Configurations
The following diagram illustrates the cabling configurations between a
Dominion KX II tiered device and a Dominion KX II base device. Connect
from a target server port on the base device to the tier Dominion KX II
Local Access port video/keyboard/mouse ports using a D2CIM-DVUSB.
If the tier device is a KX2-832 or KX2-864, connect from a target server
port on the base device directly to the tier KX2-832/KX2-864 Extended
Local port.
Diagram key
Target server
CIM from target server to the Dominion
KX II tiered device
Dominion KX II tiered device
D2CIM-DVUSB CIM from the Dominion
KX II tiered device to the Dominion KX II
base device
Dominion KX II base device
142
Chapter 8: Device Management
Enabling Direct Port Access
Direct port access allows users to bypass having to use the device's
Login dialog and Port Access page. This feature also provides the ability
to enter a username and password directly and proceed to the target if
the username and password is not contained in the URL.
The following is important URL information regarding direct port access:
If you are using VKC and direct port access:

https://IPaddress/dpa.asp?username=username&password=passwo
rd&port=port number
If you are using AKC and direct port access:

https://IPaddress/dpa.asp?username=username&password=passwo
rd&port=port number&client=akc
Where:

Username and password are optional. If they are not provided, a
login dialog will be displayed and, after being authenticated, the user
will be directly connected to the target.

The port may be a port number or port name. If you are using a port
name, the name must be unique or an error is reported. If the port is
omitted altogether, an error is reported.

For blade chassis, the port is designated <port number>'-'<slot
number>. For example, 1-2 for blade chassis connected to port 1,
slot 2.

Client=akc is optional unless you are using the AKC client. If
client=akc is not included, VKC is used as the client.
To enable direct port access:
1. Choose Device Settings > Device Services. The Device Service
Settings page appears.
2. Select Enable Direct Port Access via URL if you would like users to
have direct access to a target via the Dominion KX II by passing in
the necessary parameters in the URL.
3. Click OK.
143
Chapter 8: Device Management
Enabling the AKC Download Server Certificate Validation
If you are using the AKC client, you can choose to use the Enable AKC
Download Server Certificate Validation feature or opt not to use this
feature.
Option 1: Do Not Enable AKC Download Server Certificate
Validation (default setting)
If you do not enable AKC Download Server Certificate Validation, all KX
II users and CC-SG Bookmark and Access Client users must:

Ensure the cookies from the IP address of the device that is being
accessed are not currently being blocked.

Windows Vista, Windows 7 and Windows 2008 server users should
ensure that the IP address of the device being accessed is included
in their browser's Trusted Sites Zone and that Protected Mode is not
on when accessing the device.
Option 2: Enable AKC Download Server Certificate Validation
If you do enable AKC Download Server Certificate Validation:

Administrators must upload a valid certificate to the Dominion KX II
or generate a self-signed certificate on the Dominion KX II. The
certificate must have a valid host designation.

Each user must add the CA certificate (or a copy of self-signed
certificate) to the Trusted Root CA store in their browser.
To install the self-signed certificate when using Windows Vista®
operating system and Windows 7® operating system:
1. Include the Dominion KX II IP address in the Trusted Site zone and
ensure 'Protected Mode' is off.
2. Launch Internet Explorer® using the Dominion KX II IP address as
the URL. A Certificate Error message will be displayed.
3. Select View Certificates.
4. On the General tab, click Install Certificate. The certificate is then
installed in the Trusted Root Certification Authorities store.
5. After the certificate is installed, the Dominion KX II IP address can be
removed from the Trusted Site zone.
To enable AKC download server certificate validation:
1. Choose Device Settings > Device Services. The Device Service
Settings page appears.
2. Select the Enable AKC Download Server Certificate Validation
checkbox or you can leave the feature disabled (default).
3. Click OK.
144
Chapter 8: Device Management
Configuring Modem Settings
To configure modem settings:
1. Click Device Settings > Modem Settings to open the Modem Settings
page.
2. Select the Enable Modem checkbox. This will enable the Serial Line
Speed and Modem Init String field.
3. The Serial Line Speed of the modem is set to 115200. Read-only
4. Enter the initial modem string in the Modem Init String field. If the
modem string is left blank, the following string is sent to the modem
by default: ATZ OK AT OK.
This information is used to configure modem settings. Because
different modems have different ways of settings these values, this
document does not specify how to set these values, rather the user
should refer to the modem to create the appropriate modem-specific
string.

Modem Settings:

Enable RTS/CTS flow control

Send data to the computer on receipt of RTS

CTS should be configured to only drop if required by flow
control.

DTR should be configured for Modem resets with DTR
toggle.

DSR should be configured as always on.

DCD should be configured as enabled after a carrier signal is
detected. (that is, DCD should only be enabled when modem
connection is established with the remote side)
5. Enter the IPv4 modem server address in the Modem Server IPv4
Address field and the client modem address in the Modem Client
IPv4 Address field.
Note: The modem client and server IP addresses must be on the
same subnet and cannot overlap the KX LAN subnet.
145
Chapter 8: Device Management
6. Click OK to commit your changes or click Reset to Defaults to return
the settings to their defaults.
See Certified Modems (on page 272) for information on certified
modems that work with the Dominion KX II. For information on settings
that will give you the best performance when connecting to the Dominion
KX II via modem, see Creating, Modifying and Deleting Profiles in MPC Generation 2 Devices in the KVM and Serial Access Clients Guide.
Note: Modem access directly to the Dominion KX II HTML interface is not
supported. You must use standalone MPC to access the Dominion KX II
via modem.
Configuring Date/Time Settings
Use the Date/Time Settings page to specify the date and time for the
Dominion KX II. There are two ways to do this:

Manually set the date and time.

Synchronize the date and time with a Network Time Protocol (NTP)
server.
To set the date and time:
1. Choose Device Settings > Date/Time. The Date/Time Settings page
opens.
146
Chapter 8: Device Management
2. Choose your time zone from the Time Zone drop-down list.
3. To adjust for daylight savings time, check the "Adjust for daylight
savings time" checkbox.
4. Choose the method you would like to use to set the date and time:

User Specified Time - Choose this option to input the date and
time manually.
For the User Specified Time option, enter the date and time. For
the time, use the hh:mm format (using a 24-hour clock).

Synchronize with NTP Server - Choose this option to synchronize
the date and time with the Network Time Protocol (NTP) Server.
5. For the Synchronize with NTP Server option:
a. Enter the IP address of the Primary Time server.
b. Enter the IP address of the Secondary Time server. Optional
6. Click OK.
Note: Both IPv4 and IPv6 addresses are supported.
147
Chapter 8: Device Management
Event Management
The Dominion KX II Event Management feature provides a set of
screens for enabling and disabling the distribution of system events to
SNMP Managers, Syslog, and the audit log. These events are
categorized, and for each event you can determine whether you want the
event sent to one or several destinations.
Configuring Event Management - Settings
SNMP Configuration
Simple Network Management Protocol (SNMP) is a protocol governing
network management and the monitoring of network devices and their
functions. The Dominion KX II offers SNMP Agent support through Event
Management.
To configure SNMP (enable SNMP logging):
1. Choose Device Settings > Event Management - Settings. The Event
Management - Settings page appears.
2. Select SNMP Logging Enabled. This enables the remaining SNMP
fields.
3. In the Name, Contact, and Location fields, type the SNMP agent's
name (that is, the device's name) as it appears in the Dominion KX II
Console interface, a contact name related to this device, and where
the Dominion device is physically located.
4. Type the Agent Community String (the device's string). An SNMP
community is the group to which devices and management stations
running SNMP belong. It helps define where information is sent. The
community name is used to identify the group. The SNMP device or
agent may belong to more than one SNMP community.
5. Specify whether the community is Read-Only or Read/Write using
the Type drop-down list.
6. Configure up to five SNMP managers by specifying their Destination
IP/Host Name, Port #, and Community.
7. Click the Click here to view the Dominion SNMP MIB link to access
the SNMP Management Information Base.
8. Click OK.
To configure the Syslog (enable Syslog forwarding):
1. Select Enable Syslog Forwarding to log the device's messages to a
remote Syslog server.
148
Chapter 8: Device Management
2. Type the IP Address/Host Name of your Syslog server in the IP
Address field.
3. Click OK.
To reset to factory defaults:

Click Reset To Defaults.
Note: Both IPv4 and IPv6 addresses are supported.
Note: IPv6 addresses cannot exceed 80 characters in length for the host
name.
149
Chapter 8: Device Management
Event Management - Destinations
System events, if enabled, can generate SNMP notification events
(traps), or can be logged to Syslog or Audit Log. Use the Event
Management - Destinations page to select the system events to track
and where to send this information.
Note: SNMP traps will be generated only if the SNMP Logging Enabled
option is selected. Syslog events will be generated only if the Enable
Syslog Forwarding option is selected. Both of these options are in the
Event Management - Settings page. See Configuring Event Management
- Settings.
To select events and their destinations:
1. Choose Device Settings > Event Management - Destinations. The
Event Management - Destinations page opens.
System events are categorized by Device Operation, Device
Management, Security, User Activity, and User Group Administration.
2. Select the checkboxes for those event line items you want to enable
or disable, and where you want to send the information.
Tip: Enable or disable entire Categories by checking or clearing the
Category checkboxes, respectively.
150
Chapter 8: Device Management
3. Click OK.
151
Chapter 8: Device Management
To reset to factory defaults:

Click Reset To Defaults.
Warning: When using SNMP traps over UDP, it is possible for the
Dominion KX II and the router that it is attached to to fall out of
synchronization when the Dominion KX II is rebooted, preventing the
reboot completed SNMP trap from being logged.
SNMP Agent Configuration
SNMP-compliant devices, called agents, store data about themselves in
Management Information Bases (MIBs) and return this data to the SNMP
managers. Use the Event Logging page to configure the SNMP
connection between the Dominion KX II (SNMP Agent) and an SNMP
manager.
SNMP Trap Configuration
SNMP provides the ability to send traps, or notifications, to advise an
administrator when one or more conditions have been met. The following
table lists the Dominion KX II SNMP traps:
Trap Name
Description
bladeChassisCommError
A communications error with blade chassis device
connected to this port was detected.
Note: Not supported by the KX II-101.
152
configBackup
The device configuration has been backed up.
configRestore
The device configuration has been restored.
deviceUpdateFailed
Device update has failed.
deviceUpgradeCompleted
The Dominion KX II has completed update via an
RFP file.
deviceUpgradeStarted
The Dominion KX II has begun update via an RFP
file.
factoryReset
The device has been reset to factory defaults.
firmwareFileDiscarded
Firmware file was discarded.
firmwareUpdateFailed
Firmware update failed.
firmwareValidationFailed
Firmware validation failed.
groupAdded
A group has been added to the Dominion KX II
system.
groupDeleted
A group has been deleted from the system.
groupModified
A group has been modified.
Chapter 8: Device Management
Trap Name
Description
ipConflictDetected
An IP Address conflict was detected.
ipConflictResolved
An IP Address conflict was resolved.
networkFailure
An Ethernet interface of the product can no longer
communicate over the network.
networkParameterChanged
A change has been made to the network
parameters.
passwordSettingsChanged
Strong password settings have changed.
portConnect
A previously authenticated user has begun a KVM
session.
portConnectionDenied
A connection to the target port was denied.
portDisconnect
A user engaging in a KVM session closes the
session properly.
portStatusChange
The port has become unavailable.
powerNotification
The power outlet status notification: 1=Active,
0=Inactive.
powerOutletNotification
Power strip device outlet status notification.
rebootCompleted
The Dominion KX II has completed its reboot.
rebootStarted
The Dominion KX II has begun to reboot, either
through cycling power to the system or by a warm
reboot from the OS.
securityViolation
Security violation.
startCCManagement
The device has been put under CommandCenter
Management.
stopCCManagement
The device has been removed from
CommandCenter Management.
userAdded
A user has been added to the system.
userAuthenticationFailure
A user attempted to log in without a correct
username and/or password.
userConnectionLost
A user with an active session has experienced an
abnormal session termination.
userDeleted
A user account has been deleted.
userForcedLogout
A user was forcibly logged out by Admin
userLogin
A user has successfully logged into the Dominion
KX II and has been authenticated.
userLogout
A user has successfully logged out of the Dominion
KX II properly.
153
Chapter 8: Device Management
Trap Name
Description
userModified
A user account has been modified.
userPasswordChanged
This event is triggered if the password of any user
of the device is modified.
userSessionTimeout
A user with an active session has experienced a
session termination due to timeout.
userUploadedCertificate
A user uploaded a SSL certificate.
vmImageConnected
User attempted to mount either a device or image
on the target using Virtual Media. For every
attempt on device/image mapping (mounting) this
event is generated.
vmImageDisconnected
User attempted to unmount a device or image on
the target using Virtual Media.
Power Supply Setup
The Dominion KX II provides dual power supplies, and can automatically
detect and provide notification regarding the status of these power
supplies. Use the Power Supply Setup page to specify whether you are
using one or both of the power supplies. Proper configuration ensures
that the Dominion KX II sends the appropriate notifications should a
power supply fail. For example, if power supply number one fails, the
power LED at the front of the unit will turn red.
To enable automatic detection for the power supplies in use:
1. Choose Device Settings > Power Supply Setup. The Power Supply
Setup page opens.
154
Chapter 8: Device Management
2. If you are plugging power input into power supply number one
(left-most power supply at the back of the unit), then select the
Powerln1 Auto Detect option.
3. If you are plugging power input into power supply number two
(right-most power supply at the back of the unit), then select the
Powerln2 Auto Detect option.
4. Click OK.
Note: If either of these checkboxes is selected and power input is not
actually connected, the power LED at the front of the unit turns red.
To turn off the automatic detection:
 Deselect the checkbox for the appropriate power supply.
To reset to factory defaults:

Click the Reset To Defaults button.
Note: The Dominion KX II does NOT report power supply status to
CommandCenter. Dominion I (generation 1), however, does report
power supply status to CommandCenter.
155
Chapter 8: Device Management
Configuring Ports
The Port Configuration page displays a list of the Dominion KX II ports.
Ports connected to KVM target servers (blades and standard servers)
and power strips are displayed in blue and can be edited. For ports with
no CIM connected or with a blank CIM name, a default port name of
Dominion-KX2_Port# is assigned, where Port# is the number of the
Dominion KX II physical port.
To access a port configuration:
1. Choose Device Settings > Port Configuration. The Port Configuration
Page opens.
This page is initially displayed in port number order, but can be
sorted on any of the fields by clicking on the column heading.

Port Number - Numbered from 1 to the total number of ports
available for the Dominion KX II device.

Port Name - The name assigned to the port. A port name
displayed in black indicates that you cannot change the name
and that the port cannot be edited; port names displayed in blue
can be edited.
Note: Do not use apostrophes for the Port (CIM) Name.
156
Chapter 8: Device Management

Port Type
Port type
Description
DCIM
Dominion CIM
Not Available
No CIM connected
PCIM
Paragon CIM
PowerStrip
Power CIM
VM
Virtual media CIM (D2CIM-VUSB and
D2CIM-DVUSB)
Blade Chassis
Blade chassis and the blades associated
with that chassis (displayed in a
hierarchical order)
2. Click the Port Name for the port you want to edit.

For KVM ports, the Port page is opened. From this page, you can
name the ports and create power associations.

For power strips, the Port page for power strips is opened. From
this page, you can name the power strips and their outlets. name
the power strips and their outlets.
Configuring Standard Target Servers
To name the target servers:
1. Connect all of the target servers if you have not already done so.
See Step 3: Connect the Equipment (on page 26) for a description
of connecting the equipment.
2. Choose Device Settings > Port Configuration. The Port Configuration
page opens.
3. Click the Port Name of the target server you want to rename. The
Port Page opens.
4. Assign a name to identify the server connected to that port. The
name can be up to 32 characters, and alphanumeric and special
characters are allowed.
5. Select Standard KVM Port as the subtype for the port.
6. In the Target Settings section, select 720x400 Compensation if you
are experiencing display issues when the target is using this
resolution.
7. Select 'Use international keyboard for scan code set 3' if connecting
to the target with a DCIM-PS2 and require the use of scan code set 3
with an international keyboard.
157
Chapter 8: Device Management
8. Click OK.
Configuring KVM Switches
The Dominion KX II also supports use of hot key sequences to switch
between targets. In addition to using hot key sequences with standard
servers, KVM switching is supported by blade chassis and in tiered
configurations.
To configure KVM switches:
1. Choose Device Settings > Port Configuration. The Port Configuration
page opens.
2. Click the Port Name of the target server you want to rename. The
Port Page opens.
3. Select KVM Switch.
4. Select the KVM Switch Model.
Note: Only one switch will appear in the drop-down.
5. Select KVM Switch Hot Key Sequence.
6. Enter the Maximum Number of Target Ports (2-32).
7. In the KVM Switch Name field, enter the name you want to use to
refer to this port connection.
158
Chapter 8: Device Management
8. Activate the targets that the KVM switch hot key sequence will be
applied to. Indicate the KVM switch ports have targets attached by
selecting „Active‟ for each of the ports.
9. In the KVM Managed Links section of the page, you are able to
configure the connection to a web browser interface if one is
available.
a. Active - To activate the link once it is configured, select the
Active checkbox. Leave the checkbox deselected to keep the
link inactive. Entering information into the link fields and saving
can still be done even if Active is not selected. Once Active is
selected, the URL field is required. The username, password,
username field and password field are optional depending on
whether single sign-on is desired or not.
b. URL Name - Enter the URL to the interface.
c.
Username - Enter the username used to access the interface.
d. Password - Enter the password used to access the interface.
e. Username Field - Enter the username parameter that will be
used in the URL. For example username=admin, where
username is the username field.
f.
Password Field - Enter the password parameter that will be used
in the URL. For example password=raritan, where password is
the password field.
10. Click OK.
To change the active status of a KVM switch port or URL:
1. Choose Device Settings > Port Configuration. The Port Configuration
page opens.
2. Click the Port Name of the target server you want to rename. The
Port Page opens.
3. Deselect the Active checkbox next to the KVM switch target port or
URL to change its active status.
4. Click OK.
Configuring Power Strip (Rack PDU) Targets
The KX II allows you to connect power strips (rack PDUs) to KX II ports.
KX II power strip configuration is done from the KX II Port Configuration
page.
159
Chapter 8: Device Management
Connecting a Power Strip
Raritan PX series power strips are connected to the KX II using the
D2CIM-PWR CIM.
To connect the power strip:
1. Connect the male RJ-45 of the D2CIM-PWR to the female RJ-45
connector on the serial port of the power strip.
2. Connect the female RJ-45 connector of the D2CIM-PWR to any of
the available female system port connectors on the KX II using a
straight through Cat5 cable.
3. Attach an AC power cord to the target server and an available power
strip outlet.
4. Connect the power strip to an AC power source.
5. Power on the device.
160
Chapter 8: Device Management
Naming the Power Strip in the KX II (Port Page for Power Strips)
Note: PX power strips can be named in the PX as well as in KX II.
The Port page opens when you select a port from the Port Configuration
page that is connected to a Raritan remote power strip. The Type and
the Name fields are prepopulated.
Note: The (CIM) Type cannot be changed.
The following information is displayed for each outlet in the power strip:
[Outlet] Number, Name, and Port Association.
Use this page to name the power strip and its outlets. All names can be
up to 32 alphanumeric characters and can include special characters.
Note: When a power strip is associated with a target server (port), the
outlet name is replaced by the target server name (even if you assigned
another name to the outlet).
To name the power strip (and outlets):
Note: CommandCenter Service Gateway does not recognize power strip
names containing spaces.
1. Enter the Name of the power strip (if needed).
2. Change the [Outlet] Name if desired. (Outlet names default to the
outlet #.)
161
Chapter 8: Device Management
3. Click OK.
162
Chapter 8: Device Management
Associating Outlets with Target Servers on KX II
The Port page opens when you click on a port on the Port Configuration
page. From this page, you can make power associations, change the
port name to something more descriptive, and update target server
settings if you are using the D2CIM-VUSB CIM. The (CIM) Type and the
(Port) Name fields are prepopulated; note that the CIM type cannot be
changed.
A server can have up to four power plugs and you can associate a
different power strip with each. From this page, you can define those
associations so that you can power on, power off, and power cycle the
server from the Port Access page.
To use this feature, you will need:

Raritan remote power strip(s)

Power CIMs (D2CIM-PWR)
To make power associations (associate power strip outlets to
KVM target servers):
Note: When a power strip is associated to a target server (port), the
outlet name is replaced by the target server name (even if you assigned
another name to the outlet).
1. Choose the power strip from the Power Strip Name drop-down list.
2. For that power strip, choose the outlet from the Outlet Name
drop-down list.
3. Repeat steps 1 and 2 for all desired power associations.
4. Click OK. A confirmation message is displayed.
To change the port name:
1. Type something descriptive in the Name field. For example, the
name of the target server would be a likely candidate. The name can
be up to 32 alphanumeric characters and can include special
characters.
2. Click OK.
163
Chapter 8: Device Management
Removing Power Associations
When disconnecting target servers and/or power strips from KXII, all
power associations should first be deleted. When a target has been
associated with a power strip and the target is removed from the KX II,
the power association remains. When this occurs, you are not able to
access the Port Configuration for that disconnected target server in
Device Settings so that the power association can be properly remove.
To remove a power strip association:
1. Select the appropriate power strip from the Power Strip Name
drop-down list.
2. For that power strip, select the appropriate outlet from the Outlet
Name drop-down list.
3. From the Outlet Name drop-down list, select None.
4. Click OK. That power strip/outlet association is removed and a
confirmation message is displayed.
To remove a power strip association if the power strip has been
removed from the target:
1. Click Device Settings > Port Configuration and then click on the
active target.
2. Associate the active target to the disconnected power port. This will
break the disconnected target's power association.
3. Finally, associate the active target to the correct power port.
164
Chapter 8: Device Management
Configuring Blade Chassis
In addition to standard servers and power strips, the Dominion KX II
offers you the ability to control blade chassis that are plugged into a
Dominion KX II port. Up to eight blade chassis can be managed through
the Dominion KX II at a given time.
As with standard servers, blade chassis are autodetected by the
Dominion KX II once they are connected. When a blade server chassis is
detected by the Dominion KX II, a default name is assigned to it and it is
displayed on the Port Access page along with standard target servers
and power strips (see Port Access Page (on page 42)). The blade
chassis is displayed in an expandable, hierarchical list on the Port
Access page, with the blade chassis at the root of the hierarchy and the
individual blades labeled and displayed below the root. Use the Expand
Arrow icon next to the root chassis to display the individual blades.
Note: To view the blade chassis in a hierarchal order, blade-chassis
subtypes must be configured for the blade server chassis.
With the exception of HP® blade chassis, generic, IBM®, and Dell® blade
chassis are configured on the Port page. The port connected to the blade
chassis must be configured with the blade chassis model. The specific
information you are able to configure for a blade server will depend on
the brand of blade server you are working with. For specific information
on each of these supported blade chassis, see their corresponding topics
in this section of the help.
The following blade chassis are supported:

IBM BladeCenter® Models E and H

Dell PowerEdge® 1855, 1955 and M1000e
A Generic option allows you to configure a blade chassis that is not
included in the above list. HP BladeSystem c3000 and c7000 are
supported via individual connections from the Dominion KX II to each
blade. The ports are 'grouped' together into a chassis representation
using the Port Group Management feature.
Note: Dell PowerEdge 1855/1955 blades also provide the ability to
connect from each individual blade to a port on the Dominion KX II.
When connected in that manner, they can also be grouped to create
blade server groups.
Two modes of operation are provided for blade chassis: manual
configuration and auto-discovery, depending on the blade chassis
capabilities. If a blade chassis is configured for auto-discovery, the
Dominion KX II tracks and updates the following:

When a new blade server is added to the chassis.

When an existing blade server is removed from the chassis.
165
Chapter 8: Device Management
Note: In the case of IBM Blade Center Models E and H, the Dominion KX
II only supports auto-discovery for AMM[1] as the acting primary
management module.
The Dominion KX II also supports use of hot key sequences to switch
KVM access to a blade chassis. For blade chassis that allow users to
select a hot key sequence, those options will be provided on the Port
Configuration page. For blade chassis that come with predefined hot key
sequences, those sequences will be prepopulated on the Port
Configuration page once the blade chassis is selected. For example, the
default hot key sequence to switch KVM access to an IBM BladeCenter
H is NumLock + NumLock + SlotNumber, so this hot key sequence is
applied by default when IBM BladeCenter H is selected during the
configuration. See your blade chassis documentation for hot key
sequence information.
You are able to configure the connection to a blade chassis web browser
interface if one is available. At the chassis level, up to four links can be
defined. The first link is reserved for connection to the blade chassis
administrative module GUI. For example, this link may be used by
technical support to quickly verify a chassis configuration.
Blade chassis can be managed from the Dominion KX II Virtual KVM
Client (VKC), Raritan's Multi-Platform Client (MPC), and CC-SG.
Managing blade severs via VKC and MPC is the same as managing
standard target servers. See Working with Target Servers (on page
36) and the CC-SG Administrators Guide for more information. Any
changes made to the blade chassis configuration in Dominion KX II will
be propagated to these client applications.
Important: When the CIM connecting the blade chassis to the
Dominion KX II is powered down or disconnected from the
Dominion KX II, all established connections to the blade chassis
will be dropped. When the CIM is reconnected or powered up you
will need to re-establish the connection(s).
If you move a blade chassis from one KX II port to another KX II
port, interfaces that were added to the blade chassis node in CC-SG
will be lost in CC-SG. All other information will be retained.
Generic Blade Chassis Configuration
The Generic Blade Chassis' selection provides only a manual
configuration mode of operation. See Supported Blade Chassis
Models (on page 179), Supported CIMs for Blade Chassis (on page
180), and Required and Recommended Blade Chassis
Configurations (on page 182) for important, additional information when
configuring the blade chassis.
1. Connect the blade chassis to the Dominion KX II. See Step 3:
Connect the Equipment (on page 26) for details.
166
Chapter 8: Device Management
2. Select Device Settings > Port Configuration to open the Port
Configuration page.
3. On the Port Configuration page, click on the name of the blade
chassis you want to configure. The Port page will open.
4. Select the Blade Chassis radio button. The page will then display the
necessary fields to configure a blade chassis.
5. Select Generic from the Blade Server Chassis Model drop-down.
6. Configure the blade chassis as applicable.
a. Switch Hot Key Sequence - Define the hot key sequence that will
be used to switch from KVM to the blade chassis. The Switch
Hot Key Sequence must match the sequence used by the KVM
module in the blade chassis.
b. Administrative Module Primary IP Address/Host Name - Not
applicable.
c.
Maximum Number of Slots - Enter the default maximum number
of slots available on the blade chassis.
d. Port Number - The default port number for the blade chassis is
22. Not applicable.
e. Username - Not applicable.
f.
Password - Not applicable.
7. Change the blade chassis name if needed.
8. Indicate the blades that are installed in the blade chassis by
checking the Installed checkbox next to each slot that has a blade
installed. Alternatively, use the Select All checkbox. If needed,
change the blade server names.
9. In the Blade Chassis Managed Links section of the page, you are
able to configure the connection to a blade chassis web browser
interface if one is available. Click the Blade Chassis Managed Links
icon
page.
to expand the section on the
The first URL link is intended for use to connect to the blade chassis
Administration Module GUI.
Note: Access to the URL links entered in this section of the page is
governed by the blade chassis port permissions.
a. Active - To activate the link once it is configured, select the
Active checkbox. Leave the checkbox deselected to keep the
link inactive. Entering information into the link fields and saving
can still be done even if Active is not selected. Once Active is
selected, the URL field is required. The username, password,
username field and password field are optional depending on
whether single sign-on is desired or not.
167
Chapter 8: Device Management
b. URL - Enter the URL to the interface. Required
c.
Username - Enter the username used to access the interface.
Optional
d. Password - Enter the password used to access the interface.
Optional
Note: Leave the username and password fields blank for DRAC, ILO,
and RSA web applications or the connection will fail.
e. The Username Field and Password Field, which are both
optional, contain the labels that are expected to be associated
with the username and password entries. It is in these fields you
should enter the field names for the username and password
fields used on the login screen for the web application. You can
view the HTML source of the login screen to find the field names,
not the field labels. See Tips for Adding a Web Browser
Interface (on page 176) for tips on adding a web browser
interface. Optional
10. USB profile information does not apply to a generic configuration.
11. In the Target Settings section, select 720x400 Compensation if you
are experiencing display issues when the target is using this
resolution.
12. Select 'Use international keyboard for scan code set 3' if connecting
to the target with a DCIM-PS2 and require the use of scan code set 3
with an international keyboard.
13. Click OK to save the configuration.
Dell Blade Chassis Configuration
See Supported Blade Chassis Models (on page 179), Supported
CIMs for Blade Chassis (on page 180), and Required and
Recommended Blade Chassis Configurations (on page 182) for
important, additional information when configuring the blade chassis.
See Dell Chassis Cable Lengths and Video Resolutions (on page
296) for information on cable lengths and video resolutions when using
Dell® chassis with the Dominion KX II.
1. Connect the blade chassis to the Dominion KX II. See Step 3:
Connect the Equipment (on page 26) for details.
2. Select Device Settings > Port Configuration to open the Port
Configuration page.
3. On the Port Configuration page, click on the name of the blade
chassis you want to configure. The Port page will open.
4. Select the Blade Chassis radio button. The page will then display the
necessary fields to configure a blade chassis.
168
Chapter 8: Device Management
5. Select the Dell blade chassis model from the Blade Server Chassis
Model drop-down.
To configure a Dell PowerEdge M1000e:
1. If you selected Dell PowerEdge® M1000e, auto-discovery is
available. Configure the blade chassis as applicable. Prior to
configuring a blade chassis that can be auto-discovered, it must be
configured to enable SSH connections on the designated port
number (see Device Services (on page 137)). Additionally, a user
account with the corresponding authentication credentials must be
previously created on the blade chassis.
a. Switch Hot Key Sequence - Select the hot key sequence that will
be used to switch from KVM to the blade server. The Switch Hot
Key Sequence must match the sequence used by the KVM
module in the blade chassis.
b. Maximum Number of Slots - The default maximum number of
slots available on the blade chassis is automatically entered.
c.
Administrative Module Primary IP Address/Host Name - Enter
the primary IP address for the blade chassis. Required for
auto-discovery mode
d. Port Number - The default port number for the blade chassis is
22. Change the port number if applicable. Required for
auto-discovery mode
e. Username - Enter the username used to access the blade
chassis. Required for auto-discovery mode
f.
Password - Enter the password used to access the blade
chassis. Required for auto-discovery mode
2. If you want the Dominion KX II to auto-discover the chassis blades,
select the Blade Auto-Discovery checkbox and then click the
Discover Blades on Chassis Now button. Once the blades are
discovered, they will be displayed on the page.
3. Change the blade chassis name if needed. If the chassis is already
named, that information automatically populates this field. If it is not
already named, the Dominion KX II assigns the chassis a name. The
default naming convention for the blade chassis by the Dominion KX
II is # Blade_Chassis_Port#.
4. If operating in Manual mode, indicate the blades that are installed in
the blade chassis by checking the Installed checkbox next to each
slot that has a blade installed. Alternatively, use the Select All
checkbox. If needed, change the blade server names
If operating in Auto-discovery mode, the Installed box will display the
slots containing blades during discovery.
169
Chapter 8: Device Management
5. In the Blade Chassis Managed Links section of the page, you are
able to configure the connection to a blade chassis web browser
interface if one is available. Click the Blade Chassis Managed Links
icon
page.
to expand the section on the
The first URL link is intended for use to connect to the blade chassis
Administration Module GUI.
Note: Access to the URL links entered in this section of the page is
governed by the blade chassis port permissions.
a. Active - To activate the link once it is configured, select the
Active checkbox. Leave the checkbox deselected to keep the
link inactive. Entering information into the link fields and saving
can still be done even if Active is not selected. Once Active is
selected, the URL field is required. The username, password,
username field and password field are optional depending on
whether single sign-on is desired or not.
b. URL - Enter the URL to the interface. See Blade Chassis
Sample URL Formats (on page 184) for sample configurations
for the Dell M1000e.
c.
Username - Enter the username used to access the interface.
d. Password - Enter the password used to access the interface.
Note: Leave the username and password fields blank for DRAC, ILO,
and RSA web applications or the connection will fail.
e. The Username Field and Password Field, which are both
optional, contain the labels that are expected to be associated
with the username and password entries. It is in these fields you
should enter the field names for the username and password
fields used on the login screen for the web application. You can
view the HTML source of the login screen to find the field names,
not the field labels. See Tips for Adding a Web Browser
Interface (on page 176) for tips on adding a web browser
interface.
6. USB profiles do not apply to Dell chassis.
7. In the Target Settings section, select 720x400 Compensation if you
are experiencing display issues when the target is using this
resolution.
8. Select 'Use international keyboard for scan code set 3' if connecting
to the target with a DCIM-PS2 and require the use of scan code set 3
with an international keyboard.
9. Click OK to save the configuration.
170
Chapter 8: Device Management
To configure a Dell PowerEdge 1855/1955:
1. If you selected Dell 1855/1955, auto-discovery is not available.
Configure the blade chassis as applicable.
a. Switch Hot Key Sequence - Select the hot key sequence that will
be used to switch from KVM to the blade server.
b. Maximum Number of Slots - The default maximum number of
slots available on the blade chassis is automatically entered.
c.
Administrative Module Primary IP Address/Host Name - Not
applicable.
d. Port Number - The default port number for the blade chassis is
22. Not applicable.
e. Username - Not applicable.
f.
Password - Not applicable.
2. Change the blade chassis name if needed.
3. Indicate the blades that are installed in the blade chassis by
checking the Installed checkbox next to each slot that has a blade
installed. Alternatively, use the Select All checkbox. If needed,
change the blade server names.
4. In the Blade Chassis Managed Links section of the page, you are
able to configure the connection to a blade chassis web browser
interface if one is available. Click the Blade Chassis Managed Links
icon
page.
to expand the section on the
The first URL link is intended for use to connect to the blade chassis
Administration Module GUI.
Note: Access to the URL links entered in this section of the page is
governed by the blade chassis port permissions.
a. Active - To activate the link once it is configured, select the
Active checkbox. Leave the checkbox deselected to keep the
link inactive. Entering information into the link fields and saving
can still be done even if Active is not selected. Once Active is
selected, the URL field is required. The username, password,
username field and password field are optional depending on
whether single sign-on is desired or not.
b. URL - Enter the URL to the interface. See Blade Chassis
Sample URL Formats (on page 184) for sample configurations
for the Dell PowerEdge 1855/1955.
c.
Username - Enter the username used to access the interface.
d. Password - Enter the password used to access the interface.
171
Chapter 8: Device Management
Note: Leave the username and password fields blank for DRAC, ILO,
and RSA web applications or the connection will fail.
e. The Username Field and Password Field, which are both
optional, contain the labels that are expected to be associated
with the username and password entries. It is in these fields you
should enter the field names for the username and password
fields used on the login screen for the web application. You can
view the HTML source of the login screen to find the field names,
not the field labels. See Tips for Adding a Web Browser
Interface (on page 176) for tips on adding a web browser
interface.
5. USB profiles do not apply to Dell chassis.
6. Click OK to save the configuration.
IBM Blade Chassis Configuration
See Supported Blade Chassis Models (on page 179), Supported
CIMs for Blade Chassis (on page 180), and Required and
Recommended Blade Chassis Configurations (on page 182) for
important, additional information when configuring the blade chassis.
1. Connect the blade chassis to the Dominion KX II. See Step 3:
Connect the Equipment (on page 26) for details.
2. Select Device Settings > Port Configuration to open the Port
Configuration page.
3. On the Port Configuration page, click on the name of the blade
chassis you want to configure. The Port page will open.
4. Select the Blade Chassis radio button. The page will then display the
necessary fields to configure a blade chassis.
5. Select the IBM® blade chassis model from the Blade Server Chassis
Model drop-down.
To configure a IBM BladeCenter H and E:
1. If you selected IBM BladeCenter® H or E, auto-discovery is available.
Configure the blade chassis as applicable. Prior to configuring a
blade chassis that can be auto-discovered, it must be configured to
enable SSH connections on the designated port number (see Device
Services (on page 137)). Additionally, a user account with the
corresponding authentication credentials must be previously created
on the blade chassis. The Dominion KX II only supports
auto-discovery for AMM[1].
a. Switch Hot Key Sequence - Predefined.
b. Maximum Number of Slots - The default maximum number of
slots available on the blade chassis is automatically entered.
172
Chapter 8: Device Management
c.
Administrative Module Primary IP Address/Host Name - Enter
the primary IP address for the blade chassis. Required for
auto-discovery mode
d. Port Number - The default port number for the blade chassis is
22. Change the port number if applicable. Required for
auto-discovery mode
e. Username - Enter the username used to access the blade
chassis. Required for auto-discovery mode
f.
Password - Enter the password used to access the blade
chassis. Required for auto-discovery mode
2. If you want the Dominion KX II to auto-discover the chassis blades,
select the Blade Auto-Discovery checkbox and then click the
Discover Blades on Chassis Now button. Once the blades are
discovered, they will be displayed on the page.
3. Change the blade chassis name if needed. If the chassis is already
named, that information automatically populates this field. If it is not
already named, the Dominion KX II assigns the chassis a name. The
default naming convention for the blade chassis by the Dominion KX
II is # Blade_Chassis_Port#.
4. If operating in Manual mode, indicate the blades that are installed in
the blade chassis by checking the Installed checkbox next to each
slot that has a blade installed. Alternatively, use the Select All
checkbox. If needed, change the blade server names
If operating in Auto-discovery mode, the Installed box will display the
slots containing blades during discovery.
5. In the Blade Chassis Managed Links section of the page, you are
able to configure the connection to a blade chassis web browser
interface if one is available. Click the Blade Chassis Managed Links
icon
page.
to expand the section on the
The first URL link is intended for use to connect to the blade chassis
Administration Module GUI.
Note: Access to the URL links entered in this section of the page is
governed by the blade chassis port permissions.
a. Active - To activate the link once it is configured, select the
Active checkbox. Leave the checkbox deselected to keep the
link inactive. Entering information into the link fields and saving
can still be done even if Active is not selected. Once Active is
selected, the URL field is required. The username, password,
username field and password field are optional depending on
whether single sign-on is desired or not.
b. URL - Enter the URL to the interface. See Blade Chassis
Sample URL Formats (on page 184) for sample configurations
for the IBM BladeCenter.
173
Chapter 8: Device Management
c.
Username - Enter the username used to access the interface.
d. Password - Enter the password used to access the interface.
Note: Leave the username and password fields blank for DRAC, ILO,
and RSA web applications or the connection will fail.
e. The Username Field and Password Field, which are both
optional, contain the labels that are expected to be associated
with the username and password entries. It is in these fields you
should enter the field names for the username and password
fields used on the login screen for the web application. You can
view the HTML source of the login screen to find the field names,
not the field labels. See Tips for Adding a Web Browser
Interface (on page 176) for tips on adding a web browser
interface.
6. If applicable, define the USB profile for the blade chassis or select an
existing USB profile. Click the USB Profiles Select USB Profiles for
Port icon
or the Apply Select Profiles
to Other Ports icon
to
expand these sections of the page. See Configuring USB Profiles
(Port Page) (on page 185).
7. Click OK to save the configuration.
To configure a IBM BladeCenter (Other):
1. If you selected IBM BladeCenter (Other), auto-discovery is not
available. Configure the blade chassis as applicable.
a. Switch Hot Key Sequence - Select the hot key sequence that will
be used to switch from KVM to the blade server.
b. Administrative Module Primary IP Address/Host Name - Enter
the primary IP address for the blade chassis. Not applicable.
c.
Maximum Number of Slots - Enter the default maximum number
of slots available on the blade chassis.
d. Port Number - The default port number for the blade chassis is
22. Not applicable.
e. Username - Not applicable.
f.
Password - Not applicable.
2. Change the blade chassis name if needed.
3. Indicate the blades that are installed in the blade chassis by
checking the Installed checkbox next to each slot that has a blade
installed. Alternatively, use the Select All checkbox. If needed,
change the blade server names. If it is not already named, the
Dominion KX II assigns a name to the blade server. The default
blade server naming convention is # Blade_Chassis_Port#_Slot#.
174
Chapter 8: Device Management
4. In the Blade Chassis Managed Links section of the page, you are
able to configure the connection to a blade chassis web browser
interface if one is available. Click the Blade Chassis Managed Links
icon
page.
to expand the section on the
The first URL link is intended for use to connect to the blade chassis
Administration Module GUI.
Note: Access to the URL links entered in this section of the page is
governed by the blade chassis port permissions.
a. Active - To activate the link once it is configured, select the
Active checkbox. Leave the checkbox deselected to keep the
link inactive. Entering information into the link fields and saving
can still be done even if Active is not selected. Once Active is
selected, the URL field is required. The username, password,
username field and password field are optional depending on
whether single sign-on is desired or not.
b. URL - Enter the URL to the interface. See Blade Chassis
Sample URL Formats (on page 184) for sample configurations
for the IBM BladeCenter.
c.
Username - Enter the username used to access the interface.
d. Password - Enter the password used to access the interface.
Note: Leave the username and password fields blank for DRAC, ILO,
and RSA web applications or the connection will fail.
e. The Username Field and Password Field, which are both
optional, contain the labels that are expected to be associated
with the username and password entries. It is in these fields you
should enter the field names for the username and password
fields used on the login screen for the web application. You can
view the HTML source of the login screen to find the field names,
not the field labels. See Tips for Adding a Web Browser
Interface (on page 176) for tips on adding a web browser
interface.
5. USB profiles are not used by IBM (Other) configurations.
6. In the Target Settings section, select 720x400 Compensation if you
are experiencing display issues when the target is using this
resolution.
7. Select 'Use international keyboard for scan code set 3' if connecting
to the target with a DCIM-PS2 and require the use of scan code set 3
with an international keyboard.
8. Click OK to save the configuration.
175
Chapter 8: Device Management
Tips for Adding a Web Browser Interface
You can add a Web Browser Interface to create a connection to a device
with an embedded web server. A Web Browser interface can also be
used to connect to any web application, such as the web application
associated with an RSA, DRAC or ILO Processor card.
You must have DNS configured or URLs will not resolve. You do not
need to have DNS configured for IP addresses.
To add a web browser interface:
1. The default name for a Web Browser Interface is provided. If
needed, change the name in the Name field.
2. Enter the URL or domain name for the web application in the URL
field. You must enter the URL at which the web application expects
to read the username and password.
Follow these examples for correct formats:

http(s)://192.168.1.1/login.asp

http(s)://www.example.com/cgi/login

http(s)://example.com/home.html
3. Enter the username and password that will allow access to this
interface. Optional
4. If username and password were entered, in the Username Field and
Password Field, type the field names for the username and
password fields that are used in the login screen for the web
application. You must view the HTML source of the login screen to
find the field names, not the field labels.
Tip for locating field names:
176

In the HTML source code for the login page of the web application,
search for the field's label, such as Username and Password.

When you find the field label, look in the adjacent code for a tag that
looks like this: name="user". The word in quotes is the field name.
Chapter 8: Device Management
HP Blade Chassis Configuration (Port Group Management)
The Dominion KX II supports the aggregation of ports connected to
certain types of blades into a group representing the blade chassis.
Specifically, HP® BladeServer blades and Dell® PowerEdge® 1855/1955
blades when the Dell PowerEdge 1855/1955 is connected from each
individual blade to a port on the Dominion KX II.
The chassis is identified by a Port Group Name and the group is
designated as a Blade Server Group on the Port Group Management
page. Port Groups consist solely of ports configured as standard KVM
ports, not ports configured as blade chassis. A port may only be a
member of a single group.
Ports connected to integrated KVM modules in a blade chassis are
configured as blade chassis subtypes. These ports are eligible to be
included in port groups.
When Dominion KX II ports are connected to integrated KVM modules in
a blade chassis and not to individual blades, the ports are configured as
blade chassis subtypes. These ports are not eligible to be included in
port groups and will not appear in the Select Port for Group, Available
list.
If a standard KVM port has been included in a port group, and then is
subsequently repurposed for use as a blade chassis subtype, it must first
be removed from the port group.
Port Groups are restored using the Backup and Restore option (see
Backup and Restore (on page 211)).
To add a port group:
1. Click Device Settings > Port Group Management to open the Port
Group Management page.
2. Click the Add button to open the Port Group page.
177
Chapter 8: Device Management
3. Enter a Port Group Name. The port group name is not case sensitive
and can contain up to 32 characters.
4. Select the Blade Server Group checkbox.
If you want to designate that these ports are attached to blades
housed in a blade chassis (for example, HP c3000 or Dell
PowerEdge 1855), select the Blade Server Group checkbox.
Note: This is especially important to CC-SG users who want HP
blades to be organized on a chassis basis, although each blade has
its own connection to a port on the Dominion KX II.
5. Click on a port in the Available box in the Select Ports for Group
section. Click Add to add the port to the group. The port will be
moved to the Selected box.
6. Click OK to add the port group.
To edit port group information:
1. On the Port Group Management page, click on the link of the port
group you want to edit. The Port Group page opens.
2. Edit the information as needed.
3. Click OK to save the changes.
178
Chapter 8: Device Management
To delete a port group:
1. Click on the Port Group Management page, select the checkbox of
the port group you want to delete.
2. Click the Delete button.
3. Click OK on the warning message.
Supported Blade Chassis Models
This table contains the blade chassis models that are supported by the
Dominion KX II and the corresponding profiles that should be selected
per chassis model when configuring them in the Dominion KX II
application. A list of these models can be selected on the Port
Configuration page from the Blade Server Chassis Model drop-down,
which appears when the Blade Chassis radio button is selected. For
details on how to configure each blade chassis model, see their
corresponding topics in this section of the help.
Blade chassis model
®
Dell PowerEdge
1855/1955
®
Dell PowerEdge 1855/1955
Dell PowerEdge M1000e
®
Dominion KX II Profile
®
Dell PowerEdge M1000e
IBM BladeCenter S
IBM (Other)
IBM BladeCenter H
IBM BladeCenter H
IBM BladeCenter T
IBM (Other)
IBM BladeCenter HT
IBM (Other)
IBM BladeCenter E
IBM BladeCenter E
HP®
Configure using Port Group
Management functions. See HP Blade
Chassis Configuration (Port Group
Management) (on page 177).
179
Chapter 8: Device Management
Supported CIMs for Blade Chassis
The following CIMs are supported for blade chassis being managed
through the Dominion KX II:

DCIM-PS2

DCIM-USBG2

D2CIM-VUSB

D2CIM-DVUSB
Following is a table containing supported CIMs for each blade chassis
model that the Dominion KX II supports.
Blade chassis
Connection method
Generic
If a D2CIM-VUSB or D2CIM-DVUSB is used
when connecting to a blade-chassis configured 
as Generic, you will be able to select the USB
profiles from the Port Configuration page and
the client's USB Profile menu. However, virtual
media is not supported for generic blade
chassis and the Virtual Media menu is disabled
on the client.
Dell® PowerEdge®
1855
Includes one of the three KVM modules :

Analog KVM Ethernet switch module
(standard)

Digital Access KVM switch module
(optional)

KVM switch module (standard on systems
sold prior to April, 2005)
Recommended CIM(s)
 DCIM-PS2
DCIM-USBG2

DCIM-PS2

DCIM-PS2

DCIM-USBG2
These switches provide a custom connector
that allows two PS/2 and one video device to
be connected to the system.
Source: Dell PowerEdge 1855 User Guide
Dell PowerEdge
1955
One of two types of KVM modules may be
installed:

Analog KVM switch module

Digital Access KVM switch module
Both modules enable you to connect a
PS/2-compatible keyboard, mouse and video
monitor to the system (using a custom cable
provided with the system).
Source: Dell PowerEdge 1955 Owner's Manual
Dell PowerEdge
180
The KVM Switch Module (iKVM) is Integrated
Chapter 8: Device Management
Blade chassis
M1000e
Connection method
with this chassis.
Recommended CIM(s)
The iKVM is compatible with the following
peripherals:

USB keyboards, USB pointing devices

VGA monitors with DDC support.
Source: Dell Chassis Management Controller,
Firmware Version 1.0, User Guide
HP® BladeSystem
c3000
The HP c-Class Blade SUV Cable enables you 
to perform blade chassis administration,

configuration, and diagnostic procedures by

connecting video and USB devices directly to
the server blade.
Source: HP Proliant™ BL480c Server Blade
Maintenance and Service Guide
HP BladeSystem
c7000
The HP c-Class Blade SUV Cable enables you 
to perform server blade administration,

configuration, and diagnostic procedures by

connecting video and USB devices directly to
the server blade.
Source: HP ProLiant BL480c Server Blade
Maintenance and Service Guide
IBM® BladeCenter®
S
The Advanced Management Module (AMM)
provides system management functions and
keyboard/video/mouse (KVM) multiplexing for
all blade chassis.
DCIM-USBG2
D2CIM-VUSB
D2CIM-DVUSB (for
standard KVM port
operation without a
KVM option)
DCIM-USBG2
D2CIM-VUSB
D2CIM-DVUSB (for
standard KVM port
operation)

DCIM-USBG2

DCIM-USBG2

D2CIM-DVUSB

DCIM-USBG2

D2CIM-DVUSB
The AMM connections include: a serial port,
video connection, remote management port
(Ethernet), and two USB v2.0 ports for a
keyboard and mouse.
Source: Implementing the IBM BladeCenter S
Chassis
IBM BladeCenter H
The BladeCenter H chassis ships standard
with one Advanced Management Module.
Source: IBM BladeCenter Products and
Technology
IBM BladeCenter E
The current model BladeCenter E chassis
(8677-3Rx) ships standard with one Advanced
Management Module.
Source: IBM BladeCenter Products and
Technology
IBM BladeCenter T
The BladeCenter T chassis ships standard with 
DCIM-PS2
181
Chapter 8: Device Management
Blade chassis
Connection method
one Advanced Management Module.
Recommended CIM(s)
In contrast to the standard BladeCenter
chassis, the KVM module and the
Management Module in the BladeCenter T
chassis are separate components. The front of
the Management Module only features the
LEDs for displaying status. All Ethernet and
KVM connections are fed through to the rear to
the LAN and KVM modules.
The KVM module is a hot swap module at the
rear of the chassis providing two PS/2
connectors for keyboard and mouse, a
systems-status panel, and a HD-15 video
connector.
Source: IBM BladeCenter Products and
Technology
IBM BladeCenter HT The BladeCenter HT chassis ships standard
with one Advanced Management Module. This
module provides the ability to manage the
chassis as well as providing the local KVM
function.

DCIM-USBG2
Source: IBM BladeCenter Products and
Technology
Note: In order to support Auto-discovery, IBM BladeCenter Models H and
E must use AMM with firmware version BPET36K or later.
Note: In the case of IBM Blade Center Models E and H, the Dominion KX
II only supports auto-discovery for AMM[1] as the acting primary
management module.
Required and Recommended Blade Chassis Configurations
This table contains information on limitations and constraints that apply
to configuring blade chassis to work with the Dominion KX II. Raritan
recommends that all of the information below is followed.
Blade chassis
®
Dell PowerEdge
M1000e
182
®
Required/recommended action
 Disable the iKVM GUI screensaver. An authorize dialog will
appear, preventing iKVM from working correctly, if this is not
done.

Exit the iKVM GUI menu before attaching Dell's chassis to a
Raritan CIM. iKVM may not work correctly if this is not done.

Configure the iKVM GUI Main menu to select target blades by
Chapter 8: Device Management
Blade chassis
Dell PowerEdge
1855/1955
IBM®/Dell
Auto-Discovery
Required/recommended action
Slot, not by Name. iKVM may not work correctly if this is not
done.

Do not designate any slots for scan operations in the iKVM GUI
Setup Scan menu. iKVM may not work correctly otherwise.

Do not designate any slots for broadcast keyboard/mouse
operations in the iKVM GUI Setup Broadcast menu. iKVM may
not work correctly otherwise.

Designate a single key sequence to invoke the iKVM GUI. This
key sequence must also be identified during Dominion KX II
port configuration. Otherwise, indiscriminate iKVM operation
may occur as a result of client key entry.

Ensure that Front Panel USB/Video Enabled is not selected
during iKVM configuration via the Dell CMC GUI. Otherwise,
connections made at the front of chassis will take precedence
over the Dominion KX II connection at the rear, preventing
proper iKVM operation. A message will be displayed stating
'User has been disabled as front panel is currently active.'

Ensure that 'Allow access to CMC CLI from iKVM' is not
selected during iKVM configuration via the Dell CMC GUI.

To avoid having the iKVM GUI display upon connecting to the
blade chassis, set the Screen Delay Time to 8 seconds.

Recommend that 'Timed' and 'Displayed' be selected during
iKVM GUI Flag Setup. This will allow you to visually confirm the
connection to the desired blade slot.

Disable the iKVM GUI screensaver. An Authorize dialog will
appear if this is not done and will prevent the iKVM from
operating correctly.

Exit the iKVM GUI menu before attaching Dell's chassis to a
Raritan CIM. iKVM may not work correctly if this is not done.

Configure the iKVM GUI Main menu to select target blades by
Slot, not by Name. iKVM may not work correctly if this is not
done.

Do not designate any slots for scan operations in the iKVM GUI
Setup Scan menu or the iKVM may not work properly.

To avoid having the iKVM GUI display upon connecting to the
blade chassis, set the Screen Delay Time to 8 seconds.

Recommend that 'Timed' and 'Displayed' be selected during
iKVM GUI Flag Setup. This will allow you to visually confirm
the connection to the desired blade slot.

It is recommended that Auto-Discovery be enabled when
applying blade level access permissions. Otherwise, set access
permissions on a blade-chassis wide basis.

Secure Shell (SSH) must be enabled on the blade chassis
183
Chapter 8: Device Management
Blade chassis
IBM KX2 Virtual
Media
Required/recommended action
management module.

The SSH port configured on the blade chassis management
module and the port number entered on the Port Configuration
page must match.

Raritan Dominion KX II virtual media is supported only on IBM
BladeCenter® Models H and E. This requires the use of the
D2CIM-DVUSB. The black D2CIM-DVUSB Low-Speed USB
connector is attached to the Administrative Management
Module (AMM) at the rear of the unit. The gray D2CIM-DVUSB
High-Speed USB connector is attached to the Media Tray (MT)
at the front of the unit. This will require a USB extension cable.
Note: All IBM BladeCenters that use AMM must use AMM firmware
version BPET36K or later to work with the Dominion KX II.
Note: In the case of IBM Blade Center Models E and H, the Dominion KX
II only supports auto-discovery for AMM[1] as the acting primary
management module.
Blade Chassis Sample URL Formats
This table contains sample URL formats for blade chassis being
configured in the Dominion KX II.
Blade chassis
®
Dell M1000e
Dell 1855
IBM®
BladeCenter® E
or H
184
Sample URL format
 URL: https://192.168.60.44/cgi-bin/webcgi/login

Username: root

Username Field: user

Password: calvin

Password Field: password

URL: https://192.168.60.33/Forms/f_login

Username: root

Username Field: TEXT_USER_NAME

Password: calvin

Password Field: TEXT_PASSWORD

http://192.168.84.217/private/welcome.ssi
Chapter 8: Device Management
Configuring USB Profiles (Port Page)
You choose the available USB profiles for a port in the Select USB
Profiles for Port section of the Port page. The USB profiles chosen in the
Port page become the profiles available to the user in VKC when
connecting to a KVM target server from the port. The default is the
Windows 2000® operating system, Windows XP® operating system,
Windows Vista® operating system profile. For information about USB
profiles, see USB Profiles (on page 100).
Note: To set USB profiles for a port, you must have a VM-CIM connected
with firmware compatible with the current firmware version of the
Dominion KX II. See Upgrading CIMs (on page 215).
The profiles available to assign to a port appear in the Available list on
the left. The profiles selected for use with a port appear in the Selected
list on the right. When you select a profile in either list, a description of
the profile and its use appears in the Profile Description field.
In addition to selecting a set of profiles to make available for a KVM port,
you can also specify the preferred profile for the port and apply the
settings set for one port other KVM ports.
Note: See Mouse Modes when Using the Mac OS-X USB Profile with
a DCIM-VUSB (on page 107) for information on using the Mac OS-X®
USB profile if you are using a DCIM-VUSB or DCIM-DVUSB.
To open the Port page:
1. Choose Device Settings > Port Configuration. The Port Configuration
page opens.
2. Click the Port Name for the KVM port you want to edit. The Port
page opens.
To select the USB profiles for a KVM port:
1. In the Select USB Profiles for Port section, select one or more USB
profiles from the Available list.

Shift-Click and drag to select several continuous profiles.
185
Chapter 8: Device Management

Ctrl-Click to select several discontinuous profiles.
2. Click Add. The selected profiles appear in the Selected list. These
are the profiles that can be use for the KVM target server connected
to the port.
To specify a preferred USB profile:
1. After selecting the available profiles for a port, choose one from the
Preferred Profile for Port menu. The default is Generic. The selected
profile will be used when connecting to the KVM target server. You
can change to any other USB profile as necessary.
To remove selected USB profiles:
1. In the Select USB Profiles for Port section, select one or more
profiles from the Selected list.
186

Shift-Click and drag to select several continuous profiles.

Ctrl-Click to select several discontinuous profiles.
Chapter 8: Device Management
2. Click Remove. The selected profiles appear in the Available list.
These profiles are no longer available for a KVM target server
connected to this port.
To apply a profile selection to multiple ports:
1. In the Apply Selected Profiles to Other Ports section, select the
Apply checkbox for each KVM port you want to apply the current set
of selected USB profiles to.

To select all KVM ports, click Select All.

To deselect all KVM ports, click Deselect All.
187
Chapter 8: Device Management
Configuring Dominion KX II Local Port Settings
From the Local Port Settings page, you can customize many settings for
the Dominion KX II Local Console including keyboard, hot keys, video
switching delay, power save mode, local user interface resolution
settings, and local user authentication. Further, you can change a USB
profile from the local port.
For the KX2-832 and KX2-864, you are also able to configure the
extended local port from the Local Port Settings page. The extended
local port may be connected to a Paragon switch or User Station to
extend the reach of the Local port. Like the standard local port, you are
able configure keyboard, hot keys, video switching delay, power save
mode, local user interface resolution settings, and local user
authentication settings. The extended local port can be configured from
both the Remote Console and the Local Console. See KX2-832 and
KX2-864 Standard and Extended Local Port Settings (on page 192)
for more information on the standard local port and extended local port.
Note: If the extended local port is enabled on the KX2-832 and KX2-864
and nothing is connected to the port, you will experience a delay of 2-3
seconds when switching to a target via the local port.
To configure the local port settings:
Note: Some changes you make to the settings on the Local Port Settings
page will restart the browser you are working in. If a browser restart will
occur when a setting is changed, it is noted in the steps provider here.
1. Choose Device Settings > Local Port Settings. The Local Port
Settings page opens.
2. Select the checkbox next to the Enable Standard Local Port to
enable it. Deselect the checkbox to disable it. By default, the
standard local port is enabled but can be disabled as needed. The
browser will be restarted when this change is made. If you are using
the tiering feature, this feature will be turned off since both features
cannot be used at the same time.
3. If you are using a KX2-832 or KX2-864 device, select the checkbox
next to the Extended Local Port to enable it. Deselect the
checkbox(s) to disable it. If you are using the smart card feature, the
extended local port be must be disabled. The browser will be
restarted when this change is made.
If both the standard local port and extended local port are disabled,
the local ports cannot be accessed. If you attempt to access a
KX2-832 or KX2-864 through a disabled local port, a message will be
displayed indicating that the device is under remote management
and that the login is disabled.
188
Chapter 8: Device Management
Note: If you are using KX2-832 and KX2-864 as tiered devices, you
must connect them to the base Dominion KX II via the extended local
port.
Note: If you connect a Paragon device to the KX2-832 and KX2-864
extended local port, you must use the remote client to change the
USB profile.
4. If you are using the tiering feature, select the Enable Local Port
Device Tiering checkbox and enter the tiered secret word in the Tier
Secret field. In order to configure tiering, you must also configure the
base device on the Device Services page. See Configuring and
Enabling Tiering (on page 139) for more information on tiering.
5. Choose the appropriate keyboard type from among the options in the
drop-down list. The browser will be restarted when this change is
made.

US

US/International

United Kingdom

French (France)

German (Germany)

JIS (Japanese Industry Standard)

Simplified Chinese

Traditional Chinese

Dubeolsik Hangul (Korean)

German (Switzerland)

Portuguese (Portugal)

Norwegian (Norway)

Swedish (Sweden)

Danish (Denmark)

Belgian (Belgium)
Note: Keyboard use for Chinese, Japanese, and Korean is for
display only. Local language input is not supported at this time for
Dominion KX II Local Console functions.
6. Choose the local port hotkey. The local port hotkey is used to return
to the Dominion KX II Local Console interface when a target server
interface is being viewed. The default is to Double Click Scroll Lock,
but you can select any key combination from the drop-down list:
Hot key:
Take this action:
Double Click Scroll Lock
Press Scroll Lock key twice quickly
189
Chapter 8: Device Management
Hot key:
Take this action:
Double Click Num Lock
Press Num Lock key twice quickly
Double Click Caps Lock
Press Caps Lock key twice quickly
Double Click Left Alt key
Press the left Alt key twice quickly
Double Click Left Shift key
Press the left Shift key twice quickly
Double Click Left Ctrl key
Press the left Ctrl key twice quickly
7. Select the Local Port Connect key. Use a connect key sequence to
connect to a target and switch to another target. You can then use
the hot key to disconnect from the target and return to the local port
GUI. The connect key works for both standard servers and blade
chassis. Once the local port connect key is created, it will appear in
the Navigation panel of the GUI so you can use it as a reference.
See Connect Key Examples (on page 247) for examples of connect
key sequences.
8. Set the Video Switching Delay from between 0 - 5 seconds, if
necessary. Generally 0 is used unless more time is needed (certain
monitors require more time to switch the video).
9. If you would like to use the power save feature.
a. Select the Power Save Mode checkbox.
b. Set the amount of time (in minutes) in which Power Save Mode
will be initiated.
10. Choose the resolution for the Dominion KX II Local Console from the
drop-down list. The browser will be restarted when this change is
made.

800x600

1024x768

1280x1024
11. Choose the refresh rate from the drop-down list. The browser will be
restarted when this change is made.

60 Hz

75 Hz
12. Choose the type of local user authentication.
190

Local/LDAP/RADIUS. This is the recommended option. For more
information about authentication, see Remote Authentication
(on page 34).

None. There is no authentication for Local Console access. This
option is recommended for secure environments only.
Chapter 8: Device Management

Select the "Ignore CC managed mode on local port" checkbox if
you would like local user access to the Dominion KX II even
when the device is under CC-SG management.
Note: If you initially choose not to ignore CC Manage mode on the
local port but later want local port access, you will have to remove
the device from under CC-SG management (from within CC-SG).
You will then be able to check this checkbox.
Note: In order to use the standard local port and extended local port
while the Dominion KX II is under CC-SG management, "Ignore CC
managed mode on local port" option must be selected. Select the
"Ignore CC managed mode on local port" checkbox if you would like
local user access, via the standard or extended local port, to the
Dominion KX II when the device is under CC-SG management.
Alternatively, use the direct device access while under CC-SG
management feature.
13. Click OK.
191
Chapter 8: Device Management
KX2-832 and KX2-864 Standard and Extended Local Port Settings
The KX2-832 and KX2-864 provides you with two local port options: the
standard local port and the extended local port. Each of these port
options is enabled and disabled from the Remote Console on the Port
Configuration page or from the Local Console on the Local Port Settings
page. For more information, see Configuring Dominion KX II Local
Port Settings (on page 188).
By default, the standard local port is enabled and the extended local port
is disabled. If you would like to extend the reach of the local port, enable
the extended local port and use a Cat5/5e/6 cable to connect to the
DKX2-832 or DKX2-864 from a Paragon II UMT, EUST, UST or
URKVMG.
Note: If the extended local port is enabled on the KX2-832 and KX2-864
and nothing is connected to the port, you will experience a delay of 2-3
seconds when switching to a target via the Local port.
You must have Administrator privileges to configure these options. To
access a port, you only need to enter your username and password
once. You do not have to enter these credentials for each port you
access.
See the Specifications (on page 256) section for details on the devices
supported by the extended local port, as well as distance specifications
and supported CIMs.
KX2-832 and KX2-864 Connection Limitations
The standard and extended local ports share access to a target. When
both are enabled, the keyboard, video and mouse are shared between
the standard and extended local ports. Both will be connected to or
disconnected from the target.
When either the standard or extended local ports is disabled, the
keyboard, video and mouse for the ports will be disabled and a message
is displayed you that the local ports have been disabled.
192
Chapter 9
Security Management
In This Chapter
Security Settings....................................................................................193
Configuring IP Access Control ..............................................................202
SSL Certificates .....................................................................................205
Security Banner .....................................................................................207
Security Settings
From the Security Settings page, you can specify login limitations, user
blocking, password rules, and encryption and share settings.
Raritan SSL certificates are used for public and private key exchanges,
and provide an additional level of security. Raritan web server certificates
are self-signed. Java applet certificates are signed by a VeriSign
certificate. Encryption guarantees that your information is safe from
eavesdropping and these certificates ensure that you can trust that the
entity is Raritan, Inc.
To configure the security settings:
1. Choose Security > Security Settings. The Security Settings page
opens.
2. Update the Login Limitations (on page 194) settings as
appropriate.
3. Update the Strong Passwords (on page 195) settings as
appropriate.
4. Update the User Blocking (on page 196) settings as appropriate.
5. Update the Encryption & Share settings as appropriate.
6. Click OK.
193
Chapter 9: Security Management
To reset back to defaults:

Click Reset to Defaults.
Login Limitations
Using login limitations, you can specify restrictions for single login,
password aging, and the logging out idle users.
Limitation
Description
Enable single login
limitation
When selected, only one login per user name is
allowed at any time. When deselected, a given
user name/password combination can be
connected into the device from several client
workstations simultaneously.
Enable password
aging
When selected, all users are required to change
their passwords periodically based on the
number of days specified in Password Aging
Interval field.
This field is enabled and required when the
194
Chapter 9: Security Management
Limitation
Description
Enable Password Aging checkbox is selected.
Enter the number of days after which a password
change is required. The default is 60 days.
Log out idle users,
After (1-365
minutes)
Select the "Log off idle users" checkbox to
automatically disconnect users after the amount
of time you specify in the "After (1-365 minutes)"
field. If there is no activity from the keyboard or
mouse, all sessions and all resources are logged
out. If a virtual media session is in progress,
however, the session does not timeout.
The After field is used to set the amount of time
(in minutes) after which an idle user will be
logged out. This field is enabled when the Log
Out Idle Users option is selected. Up to 365
minutes can be entered as the field value
Strong Passwords
Strong passwords provide more secure local authentication for the
system. Using strong passwords, you can specify the format of valid
Dominion KX II local passwords such as minimum and maximum length,
required characters, and password history retention.
Strong passwords require user-created passwords to have a minimum of
8 characters with at least one alphabetical character and one
nonalphabetical character (punctuation character or number). In addition,
the first four characters of the password and the user name cannot
match.
When selected, strong password rules are enforced. Users with
passwords not meeting strong password criteria will automatically be
required to change their password on their next login. When deselected,
only the standard format validation is enforced. When selected, the
following fields are enabled and required:
Field
Description
Minimum length of strong
password
Passwords must be at least 8
characters long. The default is 8, but it
can be up to 63.
Maximum length of strong
password
The default is 16, but can be up to 64
characters long.
Enforce at least one lower
case character
When checked, at least one lower case
character is required in the password.
Enforce at least one upper
When checked, at least one upper case
195
Chapter 9: Security Management
Field
case character
Description
character is required in the password.
Enforce at least one
numeric character
When checked, at least one numeric
character is required in the password.
Enforce at least one
printable special character
When checked, at least one special
character (printable) is required in the
password.
Number of restricted
This field represents the password
passwords based on history history depth. That is, the number of
prior passwords that cannot be
repeated. The range is 1-12 and the
default is 5.
User Blocking
The User Blocking options specify the criteria by which users are blocked
from accessing the system after the specified number of unsuccessful
login attempts.
The three options are mutually exclusive:
196
Option
Description
Disabled
The default option. Users are not blocked
regardless of the number of times they fail
authentication.
Chapter 9: Security Management
Option
Description
Timer Lockout
Users are denied access to the system for the
specified amount of time after exceeding the
specified number of unsuccessful login attempts.
When selected, the following fields are enabled:
 Attempts - The number of unsuccessful login
attempts after which the user will be locked
out. The valid range is 1 - 10 and the default
is 3 attempts.
 Lockout Time - The amount of time for which
the user will be locked out. The valid range is
1 - 1440 minutes and the default is 5 minutes.
Note: Users in the role of Administrator are
exempt from the timer lockout settings.
Deactivate User-ID When selected, this option specifies that the user
will be locked out of the system after the number
of failed login attempts specified in the Failed
Attempts field:
 Failed Attempts - The number of unsuccessful
login attempts after which the user's User-ID
will be deactivated. This field is enabled when
the Deactivate User-ID option is selected. The
valid range is 1 - 10.
When a user-ID is deactivated after the specified number of failed
attempts, the administrator must change the user password and activate
the user account by selecting the Active checkbox on the User page.
Encryption & Share
Using the Encryption & Share settings you can specify the type of
encryption used, PC and VM share modes, and the type of reset
performed when the Dominion KX II Reset button is pressed.
WARNING: If you select an encryption mode that is not supported by
your browser, you will not be able to access the Dominion KX II from
your browser.
1. Choose one of the options from the Encryption Mode drop-down list.
When an encryption mode is selected, a warning appears, stating
that if your browser does not support the selected mode, you will not
be able to connect to the Dominion KX II. The warning states "When
the Encryption Mode is specified please ensure that your browser
supports this encryption mode; otherwise you will not be able to
connect to the Dominion KX II."
197
Chapter 9: Security Management
Encryption mode
Description
Auto
This is the recommended option. The
Dominion KX II autonegotiates to the highest
level of encryption possible.
You must select Auto in order for the device
and client to successfully negotiate the use of
FIPS compliant algorithms.
RC4
Secures user names, passwords and KVM
data, including video transmissions using the
RSA RC4 encryption method. This is a
128-bit Secure Sockets Layer (SSL) protocol
that provides a private communications
channel between the Dominion KX II device
and the Remote PC during initial connection
authentication.
If you enable FIPS 140-2 mode and RC4 has
been selected, you will receive an error
message. RC4 is not available while in FIPS
140-2 mode.
AES-128
The Advanced Encryption Standard (AES) is
a National Institute of Standards and
Technology specification for the encryption of
electronic data. 128 is the key length. When
AES-128 is specified, be certain that your
browser supports it, otherwise you will not be
able to connect. See Checking Your
Browser for AES Encryption (on page 200)
for more information.
AES-256
The Advanced Encryption Standard (AES) is
a National Institute of Standards and
Technology specification for the encryption of
electronic data. 256 is the key length. When
AES-256 is specified, be certain that your
browser supports it, otherwise you will not be
able to connect. See Checking Your
Browser for AES Encryption (on page 200)
for more information.
Note: MPC will always negotiate to the highest encryption and will
match the Encryption Mode setting if not set to Auto.
Note: If you are running Windows XP® operating system with Service
Pack 2, Internet Explorer® 7 cannot connect remotely to the
Dominion KX II using AES-128 encryption.
198
Chapter 9: Security Management
2. Apply Encryption Mode to KVM and Virtual Media. When selected,
this option applies the selected encryption mode to both KVM and
virtual media. After authentication, KVM and virtual media data is
also transferred with 128-bit encryption.
3. For government and other high security environments, enable FIPS
140-2 Mode by selecting the Enable FIPS 140-2 checkbox. See
Enabling FIPS 140-2 (on page 200) for information on enabling
FIPS 140-2.
4. PC Share Mode. Determines global concurrent remote KVM access,
enabling up to eight remote users to simultaneously log into one
Dominion KX II and concurrently view and control the same target
server through the device. Click the drop-down list to select one of
the following options:

Private - No PC share. This is the default mode. Each target
server can be accessed exclusively by only one user at a time.

PC-Share - KVM target servers can be accessed by up to eight
users (administrator or non-administrator) at one time. Each
remote user has equal keyboard and mouse control, however,
note that uneven control will occur if one user does not stop
typing or moving the mouse.
5. If needed, select VM Share Mode. This option is enabled only when
PC-Share mode is enabled. When selected, this option permits the
sharing of virtual media among multiple users, that is, several users
can access the same virtual media session. The default is disabled.
6. If needed, select the Disable Local Port Output checkbox. If this
option is selected, there is no video output on the local port. This
setting applies only to the KX2 832 and KX2 864. If you are using
smart card readers, the local port must be disabled.
7. If needed, select Local Device Reset Mode. This option specifies
which actions are taken when the hardware Reset button (at the
back of the device) is depressed. For more information, see
Resetting the Dominion KX II Using the Reset Button. Choose one of
the following options:
Local device reset
mode
Description
Enable Local Factory Returns the Dominion KX II device to the
Reset (default)
factory defaults.
Enable Local Admin
Password Reset
Resets the local administrator password only.
The password is reset to raritan.
Disable All Local
Resets
No reset action is taken.
199
Chapter 9: Security Management
Note: When using the P2CIM-AUSBDUAL or P2CIM-APS2DUAL to
attach a target to two Dominion KX IIs, if Private access to the targets is
required, both KVM switches must have Private set as their PC Share
Mode.
See Supported Paragon CIMS and Configurations (on page 267) for
additional information on using Paragon CIMs with the Dominion KX II.
Checking Your Browser for AES Encryption
The Dominion KX II supports AES-256. If you do not know if your
browser uses AES, check with the browser manufacturer or navigate to
the https://www.fortify.net/sslcheck.html website using the browser with
the encryption method you want to check. This website detects your
browser's encryption method and displays a report.
Note: IE6 does not support AES 128 or 256-bit encryption.
AES 256 Prerequisites and Supported Configurations
AES 256-bit encryption is supported on the following web browsers only:

Firefox® 2.0.0.x and 3

Mozilla® 1.7.13

Internet Explorer® 7 and 8
In addition to browser support, AES 256-bit encryption requires the
installation of Java™ Cryptography Extension (JCE) Unlimited Strength
Jurisdiction Policy Files.
Jurisdiction files for various JREs™ are available at the “other downloads”
section of the following link:

JRE1.6 - http://java.sun.com/javase/downloads/index_jdk5.jsp
Enabling FIPS 140-2
For government and other high security environments, enabling FIPS
140-2 mode may be desirable. The Dominion KX II uses an embedded
FIPS 140-2-validated cryptographic module running on a Linux® platform
per FIPS 140-2 Implementation Guidance section G.5 guidelines. Once
this mode is enabled, the private key used to generate the SSL
certificates must be internally generated; it cannot be downloaded or
exported.
To enable FIPS 140-2:
1. Access the Encryption & Share page (see Encryption & Share (on
page 197)).
200
Chapter 9: Security Management
2. Enable FIPS 140-2 Mode by selecting the Enable FIPS 140-2
checkbox in the Encryption & Share section of the Security Settings
page. You will utilize FIPS 140-2 approved algorithms for external
communications once in FIPS 140-2 mode. The FIPS cryptographic
module is used for encryption of KVM session traffic consisting of
video, keyboard, mouse, virtual media and smart card data.
3. Reboot the Dominion KX II. Required
Once FIPS mode is activated, 'FIPS Mode: Enabled' will be displayed
in the Device Information section in the left panel of the screen.
For additional security, you can also create a new Certificate Signing
Request once FIPS mode is activated. This will be created using the
required key ciphers. Upload the certificate after it is signed or create
a self-signed certificate. The SSL Certificate status will updated from
'Not FIPS Mode Compliant' to 'FIPS Mode Compliant'.
When FIPS mode is activated, key files cannot be downloaded or
uploaded. The most recently created CSR will be associated
internally with the key file. Further, the SSL Certificate from the CA
and its private key are not included in the full restore of the
backed-up file. The key cannot be exported from Dominion KX II.
FIPS 140-2 Support Requirements
The Dominion KX II supports the use of FIPS 140-20 approved
encryption algorithms. This allows an SSL server and client to
successfully negotiate the cipher suite used for the encrypted session
when a client is configured for FIPS 140-2 only mode.
Following are the recommendations for using FIPS 140-2 with the
Dominion KX II:
Dominion KX II
 Set the Encryption & Share to Auto on the Security Settings page.
See Encryption & Share.
Microsoft Client
 FIPS 140-2 should be enabled on the client computer and in Internet
Explorer.
To enable FIPS 140-2 on a Windows client:
1. Select Control Panel > Administrative Tools > Local Security Policy
to open the Local Security Settings dialog.
2. From the navigation tree, select Select Local Policies > Security
Options.
3. Enable "System Cryptography: Use FIPS compliant algorithms for
encryption, hashing and signing".
4. Reboot the client computer.
201
Chapter 9: Security Management
To enable FIPS 140-2 in Internet Explorer:
1. In Internet Explorer, select Tools > Internet Options and click on the
Advanced tab.
2. Select the Use TLS 1.0 checkbox.
3. Restart the browser.
Configuring IP Access Control
Using IP access control, you can control access to your Dominion KX II.
By setting a global Access Control List (ACL) you are ensuring that your
device does not respond to packets being sent from disallowed IP
addresses. The IP access control is global, affecting the Dominion KX II
as a whole, but you can also control access to your device at the group
level. See Group-Based IP ACL (Access Control List) (on page 114)
for more information about group-level control.
Important: IP address 127.0.0.1 is used by the Dominion KX II local
port. When creating an IP Access Control list, 127.0.0.1 should not
be within the range of IP addresses that are blocked or you will not
have access to the Dominion KX II local port.
To use IP access control:
1. Open the IP Access Control page by selecting Security > IP Access
Control. The IP Access Control page opens.
2. Select the Enable IP Access Control checkbox to enable IP access
control and the remaining fields on the page.
3. Choose the Default Policy. This is the action taken for IP addresses
that are not within the ranges you specify.

Accept - IP addresses are allowed access to the Dominion KX II
device.

Drop - IP addresses are denied access to the Dominion KX II
device.
Note: Both IPv4 and IPv6 addresses are supported.
To add (append) rules:
1. Type the IP address and subnet mask in the IPv4/Mask or
IPv6/Prefix Length field.
Note: The IP address should be entered using CIDR (Classless
Inter-Domain Routing notation, in which the first 24 bits are used as
a network address).
2. Choose the Policy from the drop-down list.
202
Chapter 9: Security Management
3. Click Append. The rule is added to the bottom of the rules list.
To insert a rule:
1. Type a rule #. A rule # is required when using the Insert command.
2. Type the IP address and subnet mask in the IPv4/Mask or
IPv6/Prefix Length field.
3. Choose the Policy from the drop-down list.
4. Click Insert. If the rule # you just typed equals an existing rule #, the
new rule is placed ahead of the exiting rule and all rules are moved
down in the list.
Tip: The rule numbers allow you to have more control over the order in
which the rules are created.
To replace a rule:
1. Specify the rule # you want to replace.
2. Type the IP address and subnet mask in the IPv4/Mask or
IPv6/Prefix Length field.
3. Choose the Policy from the drop-down list.
4. Click Replace. Your new rule replaces the original rule with the same
rule #.
To delete a rule:
1. Specify the rule # you want to delete.
2. Click Delete.
203
Chapter 9: Security Management
3. You are prompted to confirm the deletion. Click OK.
204
Chapter 9: Security Management
SSL Certificates
The Dominion KX II uses the Secure Socket Layer (SSL) protocol for any
encrypted network traffic between itself and a connected client. When
establishing a connection, the Dominion KX II has to identify itself to a
client using a cryptographic certificate.
It is possible to generate a Certificate Signing Request (CSR) and install
a certificate signed by the Certificate Authority (CA) on the Dominion KX
II. The CA verifies the identify of the originator of the CSR. The CA then
returns a certificate containing its signature to the originator. The
certificate, bearing the signature of the well-known CA, is used to vouch
for the identity of the presenter of the certificate.
To create and install a SSL certificate:
1. Select Security > SSL Certificate.
205
Chapter 9: Security Management
2. Complete the following fields:
a. Common name - The network name of the Dominion KX II once
it is installed in the user's network (usually the fully qualified
domain name). It is identical to the name that is used to access
the Dominion KX II with a web browser but without the prefix
“http://”. In case the name given here and the actual network
name differ, the browser will pop up a security warning when the
Dominion KX II is accessed using HTTPS.
b. Organizational unit - This field is used for specifying to which
department within an organization the Dominion KX II belongs.
c.
Organization - The name of the organization to which the
Dominion KX II belongs.
d. Locality/City - The city where the organization is located.
e. State/Province - The state or province where the organization is
located.
f.
Country (ISO code) - The country where the organization is
located. This is the two-letter ISO code, e.g. DE for Germany, or
US for the U.S.
g. Challenge Password - Some certification authorities require a
challenge password to authorize later changes on the certificate
(e.g. revocation of the certificate). The minimum length of this
password is four characters.
h. Confirm Challenge Password - Confirmation of the Challenge
Password.
i.
Email - The email address of a contact person that is responsible
for the Dominion KX II and its security.
j.
Key length - The length of the generated key in bits. 1024 is the
default.
3. Click Create to generate the Certificate Signing Request (CSR).
To download a CSR certificate:
1. The CSR and the file containing the private key used when
generating it can be downloaded by click the Download button.
Note: The CSR and the private key file are a matched set and should
be treated accordingly. If the signed certificate is not matched with
the private key used to generate the original CSR, the certificate will
not be useful. This applies to uploading and downloading the CSR
and private key files.
2. Send the saved CSR to a CA for certification. You will get the new
certificate from the CA.
206
Chapter 9: Security Management
To upload a CSR:
1. Upload the certificate to the Dominion KX II by clicking the Upload
button.
Note: The CSR and the private key file are a matched set and should
be treated accordingly. If the signed certificate is not matched with
the private key used to generate the original CSR, the certificate will
not be useful. This applies to uploading and downloading the CSR
and private key files.
After completing these three steps the Dominion KX II has its own
certificate that is used for identifying the card to its clients.
Important: If you destroy the CSR on the Dominion KX II there is no
way to get it back! In case you deleted it by mistake, you have to
repeat the three steps as described above. To avoid this, use the
download function so you will have a copy of the CSR and its
private key.
Security Banner
Dominion KX II provides you with the ability to add a security banner to
the Dominion KX II login process. This feature requires users to either
accept or decline a security agreement before they can access the
Dominion KX II. The information provided in a security banner will be
displayed in a Restricted Service Agreement dialog after users access
Dominion KX II using their login credentials.
The security banner heading and wording can be customized, or the
default text can be used. Additionally, the security banner can be
configured to require that a user accepts the security agreement before
they are able to access the Dominion KX II or it can just be displayed
following the login process. If the accept or decline feature is enabled,
the user's selection is logged in the audit log.
To configure a security banner:
1. Click Security > Banner to open the Banner page.
2. Select Display Restricted Service Banner to enable the feature.
207
Chapter 9: Security Management
3. If you want to require users to acknowledge the banner prior to
continuing the login process, select Require Acceptance of
Restricted Service Banner. In order to acknowledge the banner,
users will select a checkbox. If you do not enable this setting, the
security banner will only be displayed after the user logs in and will
not require users acknowledge it.
4. If needed, change the banner title. This information will be displayed
to users as part of the banner. Up to 64 characters can be used.
5. Edit the information in the Restricted Services Banner Message text
box. Up to 6000 characters can be entered or uploaded from a text
file. To do this, do one of the following:
a. Edit the text by manually typing in the text box. Click OK.
b. Upload the information from .txt file by selecting the Restricted
Services Banner File radio button and using the Browse feature
to locate and upload the file. Click OK. Once the file is uploaded,
the text from the file will appear in the Restricted Services
Banner Message text box.
Note: You cannot upload a text file from the local port.
208
Chapter 10 Maintenance
In This Chapter
Audit Log................................................................................................209
Device Information.................................................................................210
Backup and Restore ..............................................................................211
USB Profile Management ......................................................................214
Upgrading CIMs .....................................................................................215
Upgrading Firmware ..............................................................................216
Upgrade History .....................................................................................219
Rebooting ..............................................................................................219
Stopping CC-SG Management ..............................................................221
Audit Log
A log is created of the Dominion KX II system events.
To view the audit log for your Dominion KX II:
1. Choose Maintenance > Audit Log. The Audit Log page opens.
The Audit Log page displays events by date and time (most recent
events listed first). The Audit Log provides the following information:

Date - The date and time that the event occurred based on a
24-hour clock.

Event - The event name as listed in the Event Management
page.

Description - Detailed description of the event.
To save the audit log:
Note: Saving the audit log is available only on the Dominion KX II
Remote Console, not on the Local Console.
1. Click Save to File. A Save File dialog appears.
2. Choose the desired file name and location and click Save. The audit
log is saved locally on your client machine with the name and
location specified.
To page through the audit log:

Use the [Older] and [Newer] links.
209
Chapter 10: Maintenance
Device Information
The Device Information page provides detailed information about your
Dominion KX II device and the CIMs in use. This information is helpful
should you need to contact Raritan Technical Support.
To view information about your Dominion KX II and CIMs:

Choose Maintenance > Device Information. The Device Information
page opens.
The following information is provided about the Dominion KX II:

Model

Hardware Revision

Firmware Version

Serial Number

MAC Address
The following information is provided about the CIMs in use:
210

Port (number)

Name

Type of CIM - DCIM, PCIM, Power Strip, or VM

Firmware Version

Serial Number
Chapter 10: Maintenance
Backup and Restore
From the Backup/Restore page, you can backup and restore the settings
and configuration for your Dominion KX II.
In addition to using backup and restore for business continuity purposes,
you can use this feature as a time-saving mechanism. For instance, you
can quickly provide access to your team from another Dominion KX II by
backing up the user configuration settings from the Dominion KX II in use
and restoring those configurations to the new Dominion KX II. You can
also set up one Dominion KX II and copy its configuration to multiple
Dominion KX II devices.
To access the Backup/Restore page:

Choose Maintenance > Backup/Restore. The Backup/Restore page
opens.
Note: Backups are always complete system backups. Restores can be
complete or partial depending on your selection.
If you are using Firefox® or Internet Explorer® 5 or lower, to
backup your Dominion KX II:
1. Click Backup. A File Download dialog appears.
2. Click Save. A Save As dialog appears.
3. Choose the location, specify a file name, and click Save. A
Download Complete dialog appears.
4. Click Close. The backup file is saved locally on your client machine
with the name and location specified.
211
Chapter 10: Maintenance
If you are using Internet Explorer 6 or higher, to backup your
Dominion KX II:
1. Click Backup. A File Download dialog appears that contains an Open
button. Do not click Open.
In IE 6 and higher, IE is used as the default application to open files,
so you are prompted to open the file versus save the file. To avoid
this, you must change the default application that is used to open
files to Wordpad.
2. To do this:
a. Save the backup file. The backup file is saved locally on your
client machine with the name and location specified.
b. Once saved, locate the file and right-click on it. Select properties.
c.
In general tab, click Change and select Wordpad.
To restore your Dominion KX II:
WARNING: Exercise caution when restoring your Dominion KX II to
an earlier version. Usernames and password in place at the time of
the backup will be restored. If you do not remember the old
administrative usernames and passwords, you will be locked out of
the Dominion KX II.
In addition, if you used a different IP address at the time of the
backup, that IP address will be restored as well. If the configuration
uses DHCP, you may want to perform this operation only when you
have access to the local port to check the IP address after the update.
1. Choose the type of restore you want to run:
212
Chapter 10: Maintenance

Full Restore - A complete restore of the entire system. Generally
used for traditional backup and restore purposes.

Protected Restore - Everything is restored except device-specific
information such as IP address, name, and so forth. With this option,
you can setup one Dominion KX II and copy the configuration to
multiple Dominion KX II devices.

Custom Restore - With this option, you can select User and Group
Restore, Device Settings Restore, or both:

User and Group Restore - This option includes only user and
group information. This option does not restore the certificate
and the private key files. Use this option to quickly set up
users on a different Dominion KX II.

Device Settings Restore - This option includes only device
settings such as power associations, USB profiles, blade
chassis related configuration parameters, and Port Group
assignments. Use this option to quickly copy the device
information.
1. Click Browse. A Choose File dialog appears.
2. Navigate to and select the appropriate backup file and click Open.
The selected file is listed in the Restore File field.
3. Click Restore. The configuration (based on the type of restore
selected) is restored.
213
Chapter 10: Maintenance
USB Profile Management
From the USB Profile Management page, you can upload custom
profiles provided by Raritan tech support. These profiles are designed
to address the needs of your target server‟s configuration, in the event
that the set of standard profiles does not already address them. Raritan
tech support will provide the custom profile and work with you to verify
the solution for your target server‟s specific needs.
To access the USB Profile Management page:

Choose > Maintenance > USB Profile Management. The USB Profile
Management page opens.
To upload a custom profile to your Dominion KX II:
1. Click the Browse button. A Choose File dialog appears.
2. Navigate to and select the appropriate custom profile file and click
Open. The file selected is listed in the USB Profile File field.
3. Click Upload. The custom profile will be uploaded and displayed in
the Profile table.
Note: If an error or warning is displayed during the upload process (for
example. overwriting an existing custom profile), you may decided to
continue with the upload by clicking on Upload or cancel by clicking on
Cancel.
To delete a custom profile to your Dominion KX II:
1. Check the box corresponding to the row of the table containing the
custom profile to be deleted.
2. Click Delete. The custom profile will be deleted and removed from
the Profile table.
214
Chapter 10: Maintenance
As noted, you may delete a custom profile from the system while it is still
designated as an active profile. Doing so will terminate any virtual
media sessions that were in place.
Handling Conflicts in Profile Names
A naming conflict between custom and standard USB profiles may occur
when a firmware upgrade is performed. This may occur if a custom
profile that has been created and incorporated into the list of standard
profiles has the same name as a new USB profile that is downloaded as
part of the firmware upgrade.
Should this occur, the preexisting custom profile will be tagged as 'old_'.
For example, if a custom profile called GenericUSBProfile5 has been
created and a profile with the same name is downloaded during a
firmware upgrade, the existing file will then be called
'old_GenericUSBProfile5'.
You can delete the existing profile if needed. See USB Profile
Management (on page 214) for more information.
Upgrading CIMs
Use this procedure to upgrade CIMs using the firmware versions stored
in the memory of your Dominion KX II device. In general, all CIMs are
upgraded when you upgrade the device firmware using the Firmware
Upgrade page.
In order to make use of USB profiles, you must use a D2CIM-VUSB or
D2CIM-DVUSB with updated firmware. A VM-CIM that has not had its
firmware upgraded will support a broad range of configurations
(Windows®, Keyboard, Mouse, CD-ROM, and Removable Device) but will
not be able to make use of profiles optimized for particular target
configurations. Given this, existing VM-CIMs should be upgraded with
the latest firmware in order to access USB profiles. Until existing
VM-CIMs are upgraded, they will be able to provide functionality
equivalent to the „Generic‟ profile.
Note: Only D2CIM-VUSB can be upgraded from this page.
To upgrade CIMs using the Dominion KX II memory:
1. Choose Maintenance > CIM Firmware Upgrade. The CIM Upgrade
from page opens.
The Port (number), Name, Type, Current CIM Version, and Upgrade
CIM Version are displayed for easy identification of the CIMs.
2. Check the Selected checkbox for each CIM you want to upgrade.
Tip: Use the Select All and Deselect All buttons to quickly select all
(or deselect all) of the CIMs.
215
Chapter 10: Maintenance
3. Click the Upgrade button. You are prompted to confirm the upgrade.
4. Click OK to continue the upgrade. Progress bars are displayed
during the upgrade. Upgrading takes approximately 2 minutes or less
per CIM.
Upgrading Firmware
Use the Firmware Upgrade page to upgrade the firmware for your
Dominion KX II and all attached CIMs. This page is available in the
Dominion KX II Remote Console only.
Important: Do not turn off your Dominion KX II unit or disconnect
CIMs while the upgrade is in progress - doing so will likely result in
damage to the unit or CIMs.
To upgrade your Dominion KX II unit:
1. Locate the appropriate Raritan firmware distribution file (*.RFP) on
the Raritan website http://www.raritan.com on the Firmware
Upgrades web page.
2. Unzip the file. Please read all instructions included in the firmware
ZIP files carefully before upgrading.
Note: Copy the firmware update file to a local PC before uploading.
Do not load the file from a network drive.
3. Choose Maintenance > Firmware Upgrade. The Firmware Upgrade
page opens.
4. Click the Browse button to navigate to the directory where you
unzipped the upgrade file.
5. Select the Review CIM Version Information? checkbox if you would
like information displayed about the versions of the CIMs in use.
216
Chapter 10: Maintenance
6. Click Upload from the Firmware Upgrade page. Information about
the upgrade and version numbers is displayed for your confirmation
(if you opted to review CIM information, that information is displayed
as well):
Note: At this point, connected users are logged out, and new login
attempts are blocked.
7. Click Upgrade. Please wait for the upgrade to complete. Status
information and progress bars are displayed during the upgrade.
Upon completion of the upgrade, the unit reboots (1 beep sounds to
signal that the reboot has completed).
8. As prompted, close the browser and wait approximately 5 minutes
before logging in to the Dominion KX II again.
217
Chapter 10: Maintenance
For information about upgrading the device firmware using the
Multi-Platform Client, see Upgrading Device Firmware in the KVM and
Serial Access Clients Guide.
Note: Firmware upgrades are not supported via modem.
Note: If you are using a tiered configuration in which a base Dominion
KX II device is used to access multiple other tiered devices, you may
receive a low memory error during a firmware upgrade if you have a
large number of user groups. If you receive this error, reboot the device
and then perform the upgrade again. If you continue to receive this error
after rebooting, disable tiering on the base device and perform the
upgrade again.
218
Chapter 10: Maintenance
Upgrade History
The Dominion KX II provides information about upgrades performed on
the Dominion KX II and attached CIMS.
To view the upgrade history:

Choose Maintenance > Upgrade History. The Upgrade History page
opens.
Information is provided about the Dominion KX II upgrade(s) that have
been run, the final status of the upgrade, the start and end times, and the
previous and current firmware versions. Information is also provided
about the CIMS, which can be obtained by clicking the show link for an
upgrade. The CIM information provided is:

Type - The type of CIM.

Port - The port where the CIM is connected.

User - The user who performed the upgrade.

IP - IP address firmware location.

Start Time - Start time of the upgrade.

End Time - end time of the upgrade.

Previous Version - Previous CIM firmware version.

Upgrade Version - Current CIM firmware version.

CIMs - Upgraded CIMs.

Result - The result of the upgrade (success or fail).
Rebooting
The Reboot page provides a safe and controlled way to reboot your
Dominion KX II. This is the recommended method for rebooting.
Important: All KVM and serial connections will be closed and all
users will be logged off.
219
Chapter 10: Maintenance
To reboot your Dominion KX II:
1. Choose Maintenance > Reboot. The Reboot page opens.
2. Click Reboot. You are prompted to confirm the action. Click Yes to
proceed with the reboot.
220
Chapter 10: Maintenance
Stopping CC-SG Management
While the Dominion KX II is under CC-SG management, if you try to
access the device directly, you are notified that it the device is under
CC-SG management.
If you are managing the Dominion KX II through CC-SG and connectivity
between CC-SG and the Dominion KX II is lost after the specified
timeout interval (typically 10 minutes), you are able to end the CC-SG
management session from the Dominion KX II console.
Note: You must have the appropriate permissions to end CC-SG
management of the Dominion KX II. Additionally, the Stop CC-SG
Management option will not be provided unless you are currently using
CC-SG to manage the Dominion KX II.
To stop CC-SG management of a Dominion KX II:
1. Click Maintenance > Stop CC-SG Management. A message
indicating that the device is being managed by CC-SG will be
displayed. An option to remove the device from CC-SG management
will also be displayed.
2. Click Yes to begin the processing of removing the device from
CC-SG management. A confirmation message will then displayed
asking you to confirm that you want the remove the device from
CC-SG management.
221
Chapter 10: Maintenance
3. Click Yes to remove the device CC-SG management. Once CC-SG
management has ended, a confirmation will be displayed.
222
Chapter 11 Diagnostics
In This Chapter
Network Interface Page .........................................................................223
Network Statistics Page.........................................................................223
Ping Host Page ......................................................................................226
Trace Route to Host Page .....................................................................226
Device Diagnostics ................................................................................228
Network Interface Page
The Dominion KX II provides information about the status of your
network interface.
To view information about your network interface:

Choose Diagnostics > Network Interface. The Network Interface
page opens.
The following information is displayed:

Whether the Ethernet interface is up or down.

Whether the gateway is pingable or not.

The LAN port that is currently active.
To refresh this information:

Click the Refresh button.
Network Statistics Page
The Dominion KX II provides statistics about your network interface.
To view statistics about your network interface:
1. Choose Diagnostics > Network Statistics. The Network Statistics
page opens.
2. Choose the appropriate option from the Options drop-down list:
223
Chapter 11: Diagnostics
224

Statistics - Produces a page similar to the one displayed here.

Interfaces - Produces a page similar to the one displayed here.
Chapter 11: Diagnostics

Route - Produces a page similar to the one displayed here.
3. Click Refresh. The relevant information is displayed in the Result
field.
225
Chapter 11: Diagnostics
Ping Host Page
Ping is a network tool used to test whether a particular host or IP
address is reachable across an IP network. Using the Ping Host page,
you can determine if a target server or another Dominion KX II is
accessible.
To ping the host:
1. Choose Diagnostics > Ping Host. The Ping Host page appears.
2. Type either the hostname or IP address into the IP Address/Host
Name field.
Note: The host name cannot exceed 232 characters in length.
3. Click Ping. The results of the ping are displayed in the Result field.
Note: Both IPv4 and IPv6 addresses are supported.
Trace Route to Host Page
Trace route is a network tool used to determine the route taken to the
provided hostname or IP address.
To trace the route to the host:
1. Choose Diagnostics > Trace Route to Host. The Trace Route to Host
page opens.
226
Chapter 11: Diagnostics
2. Type either the IP address or host name into the IP Address/Host
Name field.
Note: The host name cannot exceed 232 characters in length.
3. Choose the maximum hops from the drop-down list (5 to 50 in
increments of 5).
4. Click Trace Route. The trace route command is executed for the
given hostname or IP address and the maximum hops. The output of
trace route is displayed in the Result field.
227
Chapter 11: Diagnostics
Device Diagnostics
Note: This page is for use by Raritan Field Engineers or when you are
directed by Raritan Technical Support.
Device diagnostics downloads the diagnostics information from the
Dominion KX II to the client machine. Two operations can be performed
on this page:

Execute a special diagnostics script provided by Raritan Technical
Support during a critical error debugging session. The script is
uploaded to the device and executed. Once this script has been
executed, you can download the diagnostics messages through the
Save to File button.

Download the device diagnostic log for a snapshot of diagnostics
messages from the Dominion KX II device to the client. This
encrypted file is then sent to Raritan Technical Support. Only Raritan
can interpret this file.
Note: This page is accessible only by users with administrative
privileges.
To run the Dominion KX II System diagnostics:
1. Choose Diagnostics > Dominion KX II Diagnostics. The Dominion KX
II Diagnostics page opens.
2. To execute a diagnostics script file emailed to you from Raritan
Technical Support:
a. Retrieve the diagnostics file supplied by Raritan and unzip as
necessary.
b. Use the Browse button. A Choose File dialog box opens.
c.
Navigate to and select the diagnostic file.
d. Click Open. The file is displayed in the Script File field.
e. Click Run Script. Send this file to Raritan Technical Support.
3. To create a diagnostics file to send to Raritan Technical Support:
228
Chapter 11: Diagnostics
a. Click the Save to File button. The File Download dialog opens.
b. Click Save. The Save As dialog box opens.
c.
Navigate to the desired directory and click Save.
d. Email this file as directed by Raritan Technical Support.
229
Chapter 12 Command Line Interface (CLI)
In This Chapter
Overview ................................................................................................230
Accessing the Dominion KX II Using CLI ..............................................231
SSH Connection to the Dominion KX II .................................................231
Telnet Connection to the Dominion KX II ..............................................232
Logging In ..............................................................................................233
Navigation of the CLI .............................................................................234
Initial Configuration Using CLI ...............................................................235
CLI Prompts ...........................................................................................236
CLI Commands ......................................................................................236
Administering the Dominion KX II Console Server Configuration
Commands ............................................................................................237
Configuring Network ..............................................................................238
Overview
The Command Line Interface(CLI) can be used to configure the
Dominion KX II network interface and perform diagnostic functions
provided you have the appropriate permissions to do so.
The following figures describe an overview of the CLI commands. See
CLI Commands (on page 236) for a list of all the commands, which
include definitions and links to the sections in this chapter that give
examples of these commands.
The following common commands can be used from all levels of the CLI
to the preceding figure: top, history, log off, quit, show, and help.
Note: Both IPv4 and IPv6 addresses are supported.
230
Chapter 12: Command Line Interface (CLI)
Accessing the Dominion KX II Using CLI
Access the Dominion KX II by using one of the following methods:

Telnet via IP connection

SSH (Secure Shell) via IP connection

Local Port-via RS-232 serial interface
A number of SSH/Telnet clients are available and can be obtained from
the following locations:

Putty - http://www.chiark.greenend.org.uk/~sgtatham/putty/
http://www.chiark.greenend.org.uk/~sgtatham/putty/

SSH Client from ssh.com - www.ssh.com http://www.ssh.com

Applet SSH Client - www.netspace.org/ssh
http://www.netspace.org/ssh

OpenSSH Client - www.openssh.org http://www.openssh.org
SSH Connection to the Dominion KX II
Use any SSH client that supports SSHv2 to connect to the Dominion KX
II. You must enable SSH access from the Devices Services page.
Note: For security reasons, SSH V1 connections are not supported by
the Dominion KX II.
SSH Access from a Windows PC
To open an SSH session from a Windows® PC:
1. Launch the SSH client software.
2. Enter the IP address of the Dominion KX II server. For example,
192.168.0.192.
3. Choose SSH, which uses the default configuration port 22.
4. Click Open.
The login as: prompt appears.
See Logging In (on page 233).
Note: Both IPv4 and IPv6 addresses are supported.
231
Chapter 12: Command Line Interface (CLI)
SSH Access from a UNIX/Linux Workstation
To open an SSH session from a UNIX®/Linux® workstation and
log in as the user admin, enter the following command:
ssh -l admin 192.168.30.222
The Password prompt appears.
See Logging In (on page 233).
Note: Both IPv4 and IPv6 addresses are supported.
Telnet Connection to the Dominion KX II
Due to the lack of security, user name, password and all traffic is in
clear-text on the wire. Telnet access is disabled by default.
Enabling Telnet
If you wish to use Telnet to access the Dominion KX II, first access the
Dominion KX II from the CLI or a browser.
To enable Telnet:

Enable Telnet access in the Device Settings > Device Services
menu.
Once Telnet access is enabled, you can use it to access the Dominion
KX II and set up the remaining parameters.
Access Telnet from a Windows PC
To open a Telnet session from a Windows® PC:
1. Choose Startup > Run.
2. Type Telnet in the Open text box.
3. Click OK. The Telnet page opens.
4. At the prompt enter the following command: Microsoft Telnet>
open <IP address> where <IP address> is the Dominion KX II IP
address.
5. Press the Enter key. The following message appears: Connecting
To <IP address>... The login as prompt appears.
See Logging In (on page 233).
Note: Both IPv4 and IPv6 addresses are supported.
232
Chapter 12: Command Line Interface (CLI)
Logging In
To log in, enter the user name admin as shown:
1. Log in as admin
2. The Password prompt appears. Enter the default password: raritan
The welcome message displays. You are now logged on as an
administrator.
After reviewing the following Navigation of the CLI (on page 234)
section, perform the Initial Configuration tasks.
233
Chapter 12: Command Line Interface (CLI)
Navigation of the CLI
Before using the CLI, it is important to understand CLI navigation and
syntax. There are also some keystroke combinations that simplify CLI
use.
Completion of Commands
The CLI supports the completion of partially-entered commands. After
entering the first few characters of an entry, press the Tab key. If the
characters form a unique match, the CLI will complete the entry.

If no match is found, the CLI displays the valid entries for that level.

If multiple matches are found, the CLI displays all valid entries.
Enter additional text to make the entry unique and press the Tab key to
complete the entry.
CLI Syntax -Tips and Shortcuts
Tips

Commands are listed in alphabetical order.

Commands are not case sensitive.

Parameter names are single word without underscore.

Commands without arguments default to show current settings for
the command.

Typing a question mark ( ? ) after a command produces help for that
command.

A pipe symbol ( | ) indicates a choice within an optional or required
set of keywords or arguments.
Shortcuts
234

Press the Up arrow key to display the last entry.

Press Backspace to delete the last character typed.

Press Ctrl + C to terminate a command or cancel a command if you
typed the wrong parameters.

Press Enter to execute the command.

Press Tab to complete a command. For example, Admin Port >
Conf. The system then displays the Admin Port > Config >
prompt.
Chapter 12: Command Line Interface (CLI)
Common Commands for All Command Line Interface Levels
Following are the commands that are available at all CLI levels. These
commands also help navigate through the CLI.
Commands
top
Description
Return to the top level of the CLI hierarchy, or the
“username” prompt.
history
Display the last 200 commands the user entered
into the Dominion KX II CLI.
help
Display an overview of the CLI syntax.
quit
Places the user back one level.
logout
Logs out the user session.
Initial Configuration Using CLI
Note: These steps, which use the CLI, are optional since the same
configuration can be done via KVM. See Getting Started (on page 14)
for more information.
Dominion KX II devices come from the factory with default factory
settings. When you first power up and connect to the device, you must
set the following basic parameters so the device can be accessed
securely from the network:
1. Reset the administrator password. All Dominion KX II devices are
shipped with the same default password. Therefore, to avoid security
breaches it is imperative that you change the admin password from
raritan to one customized for the administrators who will manage the
Dominion KX II device.
2. Assign the IP address, subnet mask, and gateway IP address to
allow remote access.
Note: Both IPv4 and IPv6 addresses are supported.
Setting Parameters
To set parameters, you must be logged on with administrative privileges.
At the top level, you will see the "Username" > prompt, which for the
initial configuration is "admin". Enter the top command to return to the
top menu level.
Note: If you have logged on with a different user name, that user name
will appear instead of admin.
235
Chapter 12: Command Line Interface (CLI)
Setting Network Parameters
Network parameters are configured using the interface command.
admin > Config > Network > interface enable true if lan1
ip 192.16.151.12 mask 255.255.255 gw 192.168.51.12
When the command is accepted, the device automatically drops the
connection. You must reconnect to the device using the new IP address
and the user name and password you created in the resetting factory
default password section.
Important: If the password is forgotten, the Dominion KX II will need
to be reset to the factory default from the Reset button on the back
of the Dominion KX II. The initial configuration tasks will need to be
performed again if this is done.
The Dominion KX II now has the basic configuration and can be
accessed remotely via SSH, GUI, or locally using the local serial port.
The administrator needs to configure the users and groups, services,
security, and serial ports to which the serial targets are attached to the
Dominion KX II.
Note: Both IPv4 and IPv6 addresses are supported.
CLI Prompts
The Command Line Interface prompt indicates the current command
level. The root portion of the prompt is the login name. For a direct admin
serial port connection with a terminal emulation application, Admin Port
is the root portion of a command.
admin >
For TELNET/SSH, admin is the root portion of the command:
admin > config > network >
0
CLI Commands

236
Enter admin > help.
Command
Description
config
Change to config sub menu.
diagnostics
Change to diag sub menu.
help
Display overview of commands.
Chapter 12: Command Line Interface (CLI)

Command
Description
history
Display the current session's command line history.
listports
List accessible ports.
logout
Logout of the current CLI session.
top
Return to the root menu.
userlist
List active user sessions.
Enter admin > config > network.
Command
Description
help
Display overview of commands.
history
Display the current session's command line history.
interface
Set/get network parameters.
ipv6_interface
Set/get IPv6 network parameters.
logout
Logout of the current CLI session.
name
Device name configuration.
quit
Return to previous menu.
stop
Return to the root menu.
Security Issues
Elements to consider when addressing security for console servers:

Encrypting the data traffic sent between the operator console and the
Dominion KX II device.

Providing authentication and authorization for users.

Security profile.
The Dominion KX II supports each of these elements; however, they
must be configured prior to general use.
Administering the Dominion KX II Console Server Configuration
Commands
Note: CLI commands are the same for SSH, Telnet, and Local Port
access sessions.
The Network command can be accessed in the Configuration menu for
the Dominion KX II.
237
Chapter 12: Command Line Interface (CLI)
Configuring Network
The network menu commands are used to configure the Dominion KX II
network adapter.
Commands
interface
Description
Configure the Dominion KX II device network
interface.
name
Network name configuration
ipv6
Set/get IPv6 network parameters.
Interface Command
The Interface command is used to configure the Dominion KX II network
interface. The syntax of the interface command is:
interface [ipauto <none|dhcp>] [ip <ipaddress>] [mask
<subnetmask>] [gw <ipaddress>] [mode <mode>]
Set/Get ethernet parameters
ipauto <none|dhcp> IP auto configuration (none/dhcp)
ip <ipaddress> IP Address
mask <subnetmask> Subnet Mask
gw <ipaddress> Gateway IP Address
mode <mode> Set Ehternet Mode
(auto/10hdx/10fdx/100hdx/100fdx/1000fdx)
Interface Command Example
The following command enables the interface number 1, sets the IP
address, mask, and gateway addresses, and sets the mode to auto
detect.
Admin > Config > Network > interface ipauto none ip
192.16.151.12 mask 255.255.255.0 gw 192.168.51.12 mode
auto
Note: Both IPv4 and IPv6 addresses are supported.
238
Chapter 12: Command Line Interface (CLI)
Name Command
The name command is used to configure the network name. The syntax
of the name is:
name [devicename <devicename>] [hostname <hostname>]
Device name configuration
devicename <devicename>
hostname
only)
<hostname>
Device Name
Preferred host name (DHCP
Name Command Example
The following command sets the network name:
Admin > Config > Network > name devicename My-KSX2
IPv6 Command
Use the IPv6 command to set IPv6 network parameters and retrieve
existing IPv6 parameters.
239
Chapter 13 Dominion KX II Local Console
In This Chapter
Overview ................................................................................................240
Using the Dominion KX II Local Console ..............................................240
Dominion KX II Local Console Interface................................................241
Security and Authentication ...................................................................241
Local Console Smart Card Access ........................................................242
Local Console USB Profile Options .......................................................243
Available Resolutions ............................................................................244
Port Access Page (Local Console Server Display) ...............................245
Hot Keys and Connect Keys..................................................................247
Special Sun Key Combinations .............................................................248
Accessing a Target Server ....................................................................249
Returning to the Dominion KX II Local Console Interface .....................249
Local Port Administration.......................................................................250
Resetting the Dominion KX II Using the Reset Button ..........................255
Overview
The Dominion KX II provides at-the-rack access and administration via
its local port, which features a browser-based graphical user interface for
quick, convenient switching between servers. The Dominion KX II Local
Console provides a direct analog connection to your connected servers,
which provides the same performance is as if you were directly
connected to the server's keyboard, mouse, and video ports. The
Dominion KX II Local Console provides the same administrative
functionality as the Dominion KX II Remote Console.
Using the Dominion KX II Local Console
Simultaneous Users
The Dominion KX II Local Console provides an independent access path
to the connected KVM target servers. Using the Local Console does not
prevent other users from simultaneously connecting over the network.
And even when remote users are connected to the Dominion KX II, you
can still simultaneously access your servers from the rack via the Local
Console.
240
Chapter 13: Dominion KX II Local Console
Dominion KX II Local Console Interface
When you are located at the server rack, the Dominion KX II provides
standard KVM management and administration via the Dominion KX II
Local Console. The Dominion KX II Local Console provides a direct KVM
(analog) connection to your connected servers; the performance is
exactly as if you were directly connected to the server's keyboard,
mouse, and video ports.
There are many similarities among the Dominion KX II Local Console
and the Dominion KX II Remote Console graphical user interfaces.
Where there are differences, they are noted in the help.
The Dominion KX II Local Console Factory Reset option is available in
the Dominion KX II Local Console but not the Dominion KX II Remote
Console.
Security and Authentication
In order to use the Dominion KX II Local Console, you must first
authenticate with a valid username and password. The Dominion KX II
provides a fully-integrated authentication and security scheme, whether
your access is via the network or the local port. In either case, the
Dominion KX II allows access only to those servers to which a user has
access permissions. See User Management (on page 108) for
additional information on specifying server access and security settings.
If your Dominion KX II has been configured for external authentication
services (LDAP/LDAPS, RADIUS, or Active Directory), authentication
attempts at the Local Console also are authenticated against the external
authentication service.
Note: You can also specify no authentication for Local Console access;
this option is recommended only for secure environments.
To use the Dominion KX II Local Console:
1. Connect a keyboard, mouse, and video display to the local ports at
the back of the Dominion KX II.
2. Start the Dominion KX II. The Dominion KX II Local Console
interface displays.
241
Chapter 13: Dominion KX II Local Console
Local Console Smart Card Access
To use a smart card to access a server at the Local Console, plug a USB
smart card reader into the Dominion KX II using one of the USB ports
located on the Dominion KX II. Once a smart card reader is plugged in or
unplugged from the Dominion KX II, the Dominion KX II autodetects it.
For a list of supported smart cards and additional system requirements,
see Supported and Unsupported Smart Card Readers (on page 276)
and Minimum System Requirements (on page 278).
When mounted onto the target server, the card reader and smart card
will cause the server to behave as if they had been directly attached.
Removal of the smart card or smart card reader will cause the user
session to be locked or you will be logged out depending on how the
card removal policy has been setup on the target server OS. When the
KVM session is terminated, either because it has been closed or
because you switch to a new target, the smart card reader will be
automatically unmounted from the target server.
To mount a smart card reader onto a target via the Dominion KX
II Local console:
1. Plug a USB smart card reader into the Dominion KX II using one of
the USB ports located on the device. Once attached, the smart card
reader will be detected by the Dominion KX II.
2. From the Local Console, click Tools.
3. Select the smart card reader from the Card Readers Detected list.
Select None from the list if you do not want a smart card reader
mounted.
4. Click OK. Once the smart card reader is added, a message will
appear on the page indicating you have completed the operation
successfully. A status of either Selected or Not Selected will appear
in the left panel of the page under Card Reader.
242
Chapter 13: Dominion KX II Local Console
To update the Card Readers Detected list:

Click Refresh if a new smart card has been mounted. The Card
Readers Detected list will be refreshed to reflect the newly added
smart card reader.
Smart Card Access in KX2 8 Devices
If you are using a smart card reader to access a server from the Local
Console through a KX2-832 or KX2-864 device, the extended local port
(Local Port Settings page) must be disabled. The extended local port
does not support smart card authentication.
Local Console USB Profile Options
From the USB Profile Options section of the Tools page, you can choose
from the available USB profiles for a local port.
The ports that can be assigned profiles are displayed in the Port Name
field and the profiles that are available for a port appear in the Select
Profile To Use field after the port is selected. The profiles selected for
use with a port appear in the Profile In Use field.
To apply a USB profile to a local console port:
1. In the Port Name field, select the port you want to apply the USB
profile to.
243
Chapter 13: Dominion KX II Local Console
2. In the Select Profile To Use field, select the profile to use from
among those available for the port.
3. Click OK. The USB profile will be applied to the local port and will
appear in the Profile In Use field.
Available Resolutions
The Dominion KX II Local Console provides the following resolutions to
support various monitors:

800x600

1024x768

1280x1024
Each of these resolutions supports a refresh rate of 60Hz and 75Hz.
244
Chapter 13: Dominion KX II Local Console
Port Access Page (Local Console Server Display)
After you login to the Dominion KX II Local Console, the Port Access
page opens. This page lists all of the Dominion KX II ports, the
connected KVM target servers, and their status and availability.
Also displayed on the Port Access page are blade chassis that have
been configured in the Dominion KX II. The blade chassis is displayed in
an expandable, hierarchical list on the Port Access page, with the blade
chassis at the root of the hierarchy and the individual blades labeled and
displayed below the root. Use the Expand Arrow icon next to the root
chassis to display the individual blades.
Note: To view the blade chassis in a hierarchal order, blade-chassis
subtypes must be configured for the blade server chassis.
If you are using a tiered configuration in which a base Dominion KX II
device is used to access multiple other tiered devices, the tiered devices
are viewed on the Port Access page by clicking on the Expand Arrow
icon
to the left of the base device name. See Configuring and
Enabling Tiering (on page 139) for more information on tiering.
By default, the View by Port tab will be displayed on the Port Access
page. The View by Group tab displays port groups and can be
expandable to display ports that are assigned to the port group. The
View by Search tab allows you to search by port name. The search
feature supports the use of an asterisk (*) as a wildcard, and full and
partial names.
245
Chapter 13: Dominion KX II Local Console
To use the Port Access page:
1. Log in to the Local Console.
The KVM target servers are initially sorted by Port Number. You can
change the display to sort on any of the columns.

Port Number - Numbered from 1 to the total number of ports
available for the Dominion KX II device. Note that ports
connected to power strips will not be among those listed,
resulting in gaps in the Port Number sequence.

Port Name - The name of the Dominion KX II port. Initially, this is
set to Dominion-KX2-Port# but you can change the name to
something more descriptive. When you click a Port Name link,
the Port Action Menu appears.
Note: Do not use apostrophes for the Port (CIM) Name.
246

Status - The status for standard servers is either up or down.

Type - The type of server or CIM. For blade chassis, the type can
be Blade Chassis, Blade, BladeChassisAdmin, and
BladeChassisURL. Type also includes TierDevice and
KVMSwitch.
Chapter 13: Dominion KX II Local Console

Availability - The Availability can be Idle, Connected, Busy, or
Unavailable. Blade servers will have an availability of either
shared or exclusive when a connection to that blade is in place.
2. Click View by Port or View by Group to switch between views.

In addition to the Port Number, Port Name, Status, Type, and
Availability, a Group column is also displayed on the View by
Group tab. This column contains the port groups that are
available.
3. Click the Port Name of the target server you want to access. The
Port Action Menu appears. See Port Action Menu (on page 44) for
details on available menu options.
4. Choose the desired menu command from the Port Action Menu.
To change the display sort order:

Click the column heading by which you want to sort. The list of KVM
target servers is sorted by that column.
Hot Keys and Connect Keys
Because the Dominion KX II Local Console interface is completely
replaced by the interface for the target server you are accessing, a hot
key is used to disconnect from a target and return to the local port GUI. A
connect key is used to connect to a target or switch between targets.
The Local Port hot key allows you to rapidly access the Dominion KX II
Local Console user interface when a target server is currently being
viewed. The default is to press the Scroll Lock key twice in rapid
succession, but you can designate another key combination (available in
the Local Port Settings page) as the hot key. See Dominion KX II Local
Console Local Port Settings for more information.
Connect Key Examples
Standard servers
Connect key action Key sequence example
Access a port from
the local port GUI
Access port 5 from the local port GUI:
Switch between
ports
Switch from target port 5 to port 11:
Disconnect from a
target and return to
the local port GUI
Disconnect from target port 11 and return to the
local port GUI (the page from which you
connected to target):


Press Left ALT > Press and Release 5 >
Release Left ALT
Press Left ALT > Press and Release 1 >
Press and Release 1 > Release Left ALT
247
Chapter 13: Dominion KX II Local Console
Standard servers
Connect key action Key sequence example
 Double Click Scroll Lock
Blade chassis
Connect key action Key sequence example
Access a port from
the local port GUI
Access port 5, slot 2:
Switch between
ports
Switch from target port 5, slot 2 to port 5, slot
11:


Disconnect from a
target and return to
the local port GUI
Press Left ALT > Press and Release 5 >
Press and Release - > Press and Release 2
> Release Left ALT
Press Left ALT > Press and Release 5 >
Press and Release - > Press and Release 1
> Press and Release 1 > Release Left ALT
Disconnect from target port 5, slot 11 and return
to the local port GUI (the page from which you
connected to target):

Double Click Scroll Lock
Special Sun Key Combinations
The following key combinations for Sun Microsystems server‟s special
keys operate on the local port. These special are available from the
Keyboard menu when you connect to a Sun™ target server:
248
Sun key
Local port key combination
Again
Ctrl+ Alt +F2
Props
Ctrl + Alt +F3
Undo
Ctrl + Alt +F4
Stop A
Break a
Front
Ctrl + Alt + F5
Copy
Ctrl + Alt + F6
Open
Ctrl + Alt + F7
Find
Ctrl + Alt + F9
Chapter 13: Dominion KX II Local Console
Sun key
Local port key combination
Cut
Ctrl + Alt + F10
Paste
Ctrl + Alt + F8
Mute
Ctrl + Alt + F12
Compose
Ctrl+ Alt + KPAD *
Vol +
Ctrl + Alt + KPAD +
Vol -
Ctrl + Alt + KPAD -
Stop
No key combination
Power
No key combination
Accessing a Target Server
To access a target server:
1. Click the Port Name of the target you want to access. The Port
Action Menu is displayed.
2. Choose Connect from the Port Action menu. The video display
switches to the target server interface.
Returning to the Dominion KX II Local Console Interface
Important: The Dominion KX II Local Console default hot key is to
press the Scroll Lock key twice rapidly. This key combination can
be changed in the Local Port Settings page. See Dominion KX II
Local Console Local Port Settings.
To return to the Dominion KX II Local Console from the target
server:

Press the hot key twice rapidly (the default hot key is Scroll Lock).
The video display switches from the target server interface to the
Dominion KX II Local Console interface.
249
Chapter 13: Dominion KX II Local Console
Local Port Administration
The Dominion KX II can be managed by either the Dominion KX II Local
Console or the Dominion KX II Remote Console. Note that the Dominion
KX II Local Console also provides access to:

Factory Reset

Local Port Settings(available in the Remote Console, as well)
Note: Only users with administrative privileges can access these
functions.
Configuring Dominion KX II Local Console Local Port Settings
From the Local Port Settings page, you can customize many settings for
the Dominion KX II Local Console including keyboard, hot keys, video
switching delay, power save mode, local user interface resolution
settings, and local user authentication.
Note: Only users with administrative privileges can access these
functions.
To configure the local port settings:
Note: Some changes you make to the settings on the Local Port Settings
page will restart the browser you are working in. If a browser restart will
occur when a setting is changed, it is noted in the steps provider here.
1. Choose Device Settings > Local Port Settings. The Local Port
Settings page opens.
2. Choose the appropriate keyboard type from among the options in the
drop-down list. The browser will be restarted when this change is
made.
250

US

US/International

United Kingdom

French (France)

German (Germany)

JIS (Japanese Industry Standard)

Simplified Chinese

Traditional Chinese

Dubeolsik Hangul (Korean)
Chapter 13: Dominion KX II Local Console

German (Switzerland)

Portuguese (Portugal)

Norwegian (Norway)

Swedish (Sweden)

Danish (Denmark)

Belgian (Belgium)
Note: Keyboard use for Chinese, Japanese, and Korean is for
display only. Local language input is not supported at this time for
Dominion KX II Local Console functions.
3. Choose the local port hotkey. The local port hotkey is used to return
to the Dominion KX II Local Console interface when a target server
interface is being viewed. The default is to Double Click Scroll Lock,
but you can select any key combination from the drop-down list:
Hot key:
Take this action:
Double Click Scroll Lock
Press Scroll Lock key twice quickly
Double Click Num Lock
Press Num Lock key twice quickly
Double Click Caps Lock
Press Caps Lock key twice quickly
Double Click Left Alt key
Press the left Alt key twice quickly
Double Click Left Shift key
Press the left Shift key twice quickly
Double Click Left Ctrl key
Press the left Ctrl key twice quickly
4. Select the Local Port Connect key. Use a connect key sequence to
connect to a target and switch to another target. You can then use
the hot key to disconnect from the target and return to the local port
GUI. The connect key works for both standard servers and blade
chassis. Once the local port connect key is created, it will appear in
the Navigation panel of the GUI so you can use it as a reference.
See Connect Key Examples (on page 247) for examples of connect
key sequences.
5. Set the Video Switching Delay from between 0 - 5 seconds, if
necessary. Generally 0 is used unless more time is needed (certain
monitors require more time to switch the video).
6. If you would like to use the power save feature.
a. Select the Power Save Mode checkbox.
b. Set the amount of time (in minutes) in which Power Save Mode
will be initiated.
7. Choose the resolution for the Dominion KX II Local Console from the
drop-down list. The browser will be restarted when this change is
made.

800x600
251
Chapter 13: Dominion KX II Local Console

1024x768

1280x1024
8. Choose the refresh rate from the drop-down list. The browser will be
restarted when this change is made.

60 Hz

75 Hz
9. Choose the type of local user authentication.

Local/LDAP/RADIUS. This is the recommended option. For more
information about authentication, see Remote Authentication
(on page 34).

None. There is no authentication for Local Console access. This
option is recommended for secure environments only.

Select the "Ignore CC managed mode on local port" checkbox if
you would like local user access to the Dominion KX II even
when the device is under CC-SG management.
Note: If you initially choose not to ignore CC Manage mode on the
local port but later want local port access, you will have to remove
the device from under CC-SG management (from within CC-SG).
You will then be able to check this checkbox.
252
Chapter 13: Dominion KX II Local Console
10. Click OK.
Configuring Dominion KX II Local Port Settings from the Local Console
The standard local port and the extended local port can be configured
from the Remote Console on the Port Configuration page or from the
Local Console on the Local Port Settings page. See Configuring
Dominion KX II Local Port Settings (on page 188) for details on
configuring these ports.
253
Chapter 13: Dominion KX II Local Console
Dominion KX II Local Console Factory Reset
Note: This feature is available only on the Dominion KX II Local Console.
The Dominion KX II offers several types of reset modes from the Local
Console user interface.
Note: It is recommended that you save the audit log prior to performing a
factory reset. The audit log is deleted when a factory reset is performed
and the reset event is not logged in the audit log. For more information
about saving the audit log, see Audit Log.
To perform a factory reset:
1. Choose Maintenance > Factory Reset. The Factory Reset page
opens.
2. Choose the appropriate reset option from the following options:

Full Factory Reset - Removes the entire configuration and resets the
device completely to the factory defaults. Note that any management
associations with CommandCenter will be broken. Because of the
complete nature of this reset, you will be prompted to confirm the
factory reset.

Network Parameter Reset - Resets the network parameters of the
device back to the default values (click Device Settings > Network
Settings to access this information):

IP auto configuration

IP address

Subnet mask

Gateway IP address

Primary DNS server IP address

Secondary DNS server IP address

Discovery port

Bandwidth limit

LAN interface speed & duplex

Enable automatic failover

Ping interval (seconds)

Timeout (seconds)
1. Click Reset to continue. You will be prompted to confirm the factory
reset because all network settings will be permanently lost.
2. Click OK button proceed. Upon completion, the Dominion KX II
device is automatically restarted.
254
Chapter 13: Dominion KX II Local Console
Resetting the Dominion KX II Using the Reset Button
On the back panel of the device, there is a Reset button. It is recessed to
prevent accidental resets (you will need a pointed object to press this
button).
The actions that are performed when the Reset button is pressed are
defined in the graphical user interface. See Encryption & Share.
Note: It is recommended that you save the audit log prior to performing a
factory reset. The audit log is deleted when a factory reset is performed
and the reset event is not logged on the audit log. For more information
about saving the audit log, see Audit Log.
To reset the device:
1. Power off the Dominion KX II.
2. Use a pointed object to press and hold the Reset button.
3. While continuing to hold the Reset button, power the Dominion KX II
device back on.
4. Continue holding the Reset button for 10 seconds. Once the device
has been reset, two short beeps signal its completion.
255
Appendix A Specifications
In This Chapter
Physical Specifications ..........................................................................256
Environmental Requirements ................................................................258
Computer Interface Modules (CIMs) .....................................................259
Supported CIMs and Operating Systems (Target Servers) ..................261
Supported Paragon CIMS and Configurations ......................................267
Supported Operating Systems (Clients) ................................................271
Supported Browsers ..............................................................................272
Certified Modems ..................................................................................272
Devices Supported by the KX2-832 and KX2-864 Extended Local Port273
Target Server Connection Distance and Video Resolution ...................273
KX2-832 and KX2-864 Extended Local Port Recommended Maximum
Distances ...............................................................................................273
Remote Connection ...............................................................................274
Supported Video Resolutions ................................................................274
Supported Keyboard Languages ...........................................................275
Smart Card Readers..............................................................................276
TCP and UDP Ports Used .....................................................................279
Network Speed Settings ........................................................................281
Physical Specifications
Dominion KX II Specifications
Part
number
Line item
description
UPC code
Power
DKX2-108
8-Port
Dominion KX
II with 1-user
network
access and
local port,
virtual media,
dual power
785813624109
16-Port
Dominion KX
II with 1-user
network
access and
local port,
virtual media,
dual power
785813624055
DKX2-116
Weight
Product
dimensions
(WxDxH)
Shipping
weight
Shipping
dimensions
(WxDxH)
Dual power 8.58 lbs
100/240 V
50/60 Hz
0.6A
3.9 kg
25 Watts
1.75" x
17.32" x
11.4"
14.3 lbs
22" x 16.6" x
6.5"
44mm x
439mm x
290mm
6.5 kg
559mm x
422mm x
165mm
Dual power 8.65 lbs
100/240 V
50/60 Hz
3.9 kg
0.6A
25.4 Watts
1.75" x 17.3"
x 11.4"
14.85 lbs
22" x 16.6" x
6.5"
44mm x
439mm x
290mm
6.7 kg
559mm x
422mm x
165mm
256
Appendix A: Specifications
Part
number
Line item
description
UPC code
Power
DKX2-132
32-Port
Dominion KX
II with 1-user
network
access and
local port,
virtual media,
dual power
785813624079
16-Port
Dominion KX
II with 2-user
network
access and
local port,
virtual media,
dual power
785813624086
32-Port
Dominion KX
II with 2-user
network
access and
local port,
virtual media,
dual power
785813625021
16-Port
Dominion KX
II with 4-user
network
access and
local port,
virtual media,
dual power
785813625359
32-Port
Dominion KX
II with 4-user
network
access and
local port,
virtual media,
dual power
785813625380
DKX2-216
DKX2-232
DKX2-416
DKX2-432
Weight
Product
dimensions
(WxDxH)
Shipping
weight
Shipping
dimensions
(WxDxH)
Dual power 9.0 lbs
100/240 V
50/60 Hz
4.1 kg
0.6A
26 Watts
1.75" x 17.3"
x 11.4"
14.9 lbs
22" x 16.6" x
6.5"
44mm x
439mm x
290mm
6.8 kg
559mm x
422mm x
165mm
Dual power 8.65 lbs
100/240 V
50/60 Hz
3.9 kg
0.6A
26.3 Watts
1.75" x 17.3"
x 11.4"
14.49 lbs
22" x 16.6" x
6.5"
44mm x
439mm x
290mm
6.6 kg
559mm x
422mm x
165mm
Dual power 9.0 lbs
100/240 V
50/60 Hz
(optimal 47 4.1 kg
- 63 Hz)
0.6A
27 Watts
1.75" x 17.3"
x 11.4"
14.9 lbs
22" x 16.6" x
6.5"
44mm x
439mm x
290mm
6.8 kg
559mm x
422mm x
165mm
Dual power 9.04 lbs
100/240 V
50/60 Hz
4.1 kg
1A
62 Watts
17.3” x 11.6”
x 1.75”
14.94 lbs
22” x 16.5” x
6.5”
Dual power 9.48 lbs
100/240 V
50/60 Hz
4.3 kg
1A
64 Watts
17.3” x 11.6”
x 1.75”
440 mm x
6.8 kg
295 mm x 44
mm
560 mm x 420
mm x 165 mm
15.38 lbs 22” x 16.5” x
6.5”
440 mm x
7.0 kg
295 mm x 44
mm
560 mm x 420
mm x 165 mm
257
Appendix A: Specifications
Part
number
Line item
description
UPC code
Power
Weight
Product
dimensions
(WxDxH)
Shipping
weight
Shipping
dimensions
(WxDxH)
DKX2-464
64-Port
Dominion KX
II with 4-user
network
access and
local port,
virtual media,
dual power
785813625298
Dual power 11.29
100/240 V lbs
50/60 Hz
5.12 kg
1A
64 Watts
17.3” x 11.6”
x 3.5”
19.8 lbs
22” x 16.5” x
6.5”
440 mm x
9 kg
295 mm x 88
mm
560 mm x 420
mm x 165 mm
KX2-8 Specifications
Part
number
Line item
description
UPC code
Power
Weight Product
dimensions
(WxDxH)
DKX2-83 32-Port
0785813620019
2
Dominion KX II
with 8-user
network access,
standard local
port, extended
local port, virtual
media, dual
power
Dual power 10.57
100/240 V lbs
50/60 Hz
DKX2-86 64-Port
0785813620026
4
Dominion KX II
with 8-user
network access,
standard local
port, extended
local port, virtual
media, dual
power
Dual power 13.22
100/240 V lbs
50/60 Hz
1.2A
6.0 kg
64 Watts
Environmental Requirements
Operating
Temperature
0°C- 40°C (32°F - 104°F)
Humidity
20% - 85% RH
258
1A (0.5A)
64 Watts
4.8 kg
17.3” x 14.2”
x 1.73”
Shipping
weight
Shipping
dimensions
(WxDxH)
35.90 lbs 22” x 18.5” x
11”
440 mm x
16.3 kg
360 mm x 44
mm
560 mm x 470
mm x 280 mm
17.3” x 14.6”
x 3.5”
21.7” x 20.1” x
7.5”
22.47 lbs
440 mm x
10.2 kg
370 mm x 88
mm
550 mm x 510
mm x 190 mm
Appendix A: Specifications
Operating
Altitude
N/A
Vibration
5-55-5 HZ, 0.38mm, 1 minutes per cycle;
30 minutes for each axis (X, Y, Z)
Shock
N/A
Non-Operating
Temperature
0°C- 50°C (32°F - 122°F)
Humidity
10% - 90% RH
Altitude
N/A
Vibration
5-55-5 HZ, 0.38mm, 1 minutes per cycle;
30 minutes for each axis (X, Y, Z)
Shock
N/A
Computer Interface Modules (CIMs)
Part number
Line item
description
D2CIM-VUSB
Product
weight
Product
dimensions
(WxDxH)
Shipping
weight
Shipping
dimensions
(WxDxH)
UPC code
Dominion KX II 0.2 lbs
Computer
Interface Module
[USB Port with
Virtual Media]
1.3" x 3.0" x 0.6"
0.2 lbs
7.2" x 9" x
0.6"
785813332004
DCIM-PS2
Dominion KX I & 0.2 lbs
II Computer
Interface Module
[PS/2 Port]
1.3" x 3.0" x 0.6"
0.2 lbs
7.2" x 9" x
0.6"
785813338532
DCIM-USB
Dominion KX I & 0.2 lbs
II Computer
Interface Module
[USB Port]
1.3" x 3.0" x 0.6"
0.2 lbs
7.2" x 9" x
0.6"
785813338518
DCIM-SUSB
Dominion KX I & 0.2 lbs
II Computer
Interface Module
[USB Port for
Sun]
1.3" x 3.0" x 0.6"
0.2 lbs
7.2" x 9" x
0.6"
785813338556
DCIM-USBG2 Dominion KX I & 0.2 lbs
II Computer
1.3” x 3.0” x 0.6”
0.2 lbs
7.2” x 9” x 0.6 785813338884
259
Appendix A: Specifications
Part number
Line item
description
Product
weight
Product
dimensions
(WxDxH)
Shipping
weight
Shipping
dimensions
(WxDxH)
UPC code
Interface Module
[USB and Sun
USB Port] G2
CIM
DCIM-SUN
Dominion KX I & 0.2 lbs
II Computer
Interface Module
[Sun Port, HD15
Video]
1.3" x 3.0" x 0.6"
0.2 lbs
7.2" x 9" x
0.6"
785813338549
D2CIM-PWR
Dominion KX II 0.2 lbs
Computer
Interface Module
for Remote
Power strips
1.3" x 3.0" x 0.6"
0.2 lbs
7.2" x 9" x
0.6"
785813332011
D2CIM-VUSB- Bulk pack of 32
32PAC
D2CIM-VUSB
6.4 lb
(1.3" x 3.0" x
0.6")*32
8.01 lb
21.65"x12.20 785813332028
"x4.33"
D2CIM-VUSB
-64PAC
12.8 lb
(1.3" x 3.0" x
0.6")*64
18.13 lb
22.64"x9.45"
x12.99"
785813332035
D2CIM-DVUS Dominion KX II 0.23 lbs,
B
Computer
105 g
Interface Module
[Dual USB Port
with Virtual
Media]
3.53”x1.68”x.76”
.25 lbs,
112.5 g
3.9”x5.7”x
1.0”
785813339508
D2CIM-DVUS Bulk pack of 32
B-32PAC
D2CIM-DVUSB
21.9”x12.2”x4.3”
Bulk pack of 64
D2CIM-VUSB
D2CIM-DVUS Bulk pack of 64
B -64PAC
D2CIM-DVUSB
260
10.1 lbs,
4.6 kg
22.5 lbs,
10.2 kg
89.7x42.7x19.3
(mm)
555x310x110
(mm)
9.4”x22.6”x13.0”
240x575x330
(mm)
100*145*27
(mm)
10.1 lbs, 4.6 21.9”x12.2”x4 785813332080
kg
.3”
555x310x110
(mm)
22.5 lbs,
10.2 kg
9.4”x22.6”x13 785813332097
.0”
240*575*330
(mm)
Appendix A: Specifications
Supported CIMs and Operating Systems (Target Servers)
In addition to the new Dominion KX II D2CIMs, most Paragon® and
Dominion KX I CIMs are supported. The following table displays the
supported target server operating systems, CIMs, virtual media, and
mouse modes.
Note: Only 32 BIT operating systems for Windows® and Linux® target
servers are supported for Generation 1 devices.
261
Appendix A: Specifications
Supported
Paragon CIMs

P2CIM-PS2
Operating system and
serial devices (where
applicable)
 Windows XP®

Windows 2000®

Windows 2000
Server®

Windows 2003
Server®

Windows Vista®

Windows 7®

Windows 2008®

Red Hat® Enterprise
Linux® 4 ES

Red Hat Enterprise
Linux 5

Open SUSE 10, 11

Fedora® 8 - 11

IBM® AIX™

HP UX

P2CIM-AUSB

Windows XP

UUSBPD

Windows 2000

Windows 2000
Server

Windows 2003
Server

Windows Vista

Windows 7

Windows 2008

Red Hat Enterprise
Linux 4 ES

Red Hat Enterprise
Linux 5

Open SUSE 10, 11

Fedora 8 - 11

IBM AIX

HP UX

Mac® OS
262
Virtual
media
Absolute
Mouse
mode
Intelligent
Standard
Mouse mode Mouse mode
Appendix A: Specifications
Supported
Paragon CIMs

UKVMPD
(version 0C4)
Note: Version 0C5
does not work with
Dominion KX II.

P2CIM-SUN

P2CIM-SUSB

P2CIM-SER
Operating system and
serial devices (where
applicable)
 Windows XP

Windows 2000

Windows 2000
Server

Windows 2003
Server

Windows Vista

Windows 7

Windows 2008

Red Hat Enterprise
Linux 4 ES

Red Hat Enterprise
Linux 5

Open SUSE 10, 11

Fedora 8 - 11

All Solaris™ OSs
supported in
Dominion KX I

Serial devices
Virtual
media
Absolute
Mouse
mode
Intelligent
Standard
Mouse mode Mouse mode
263
Appendix A: Specifications
Supported
Dominion KX I
DCIMs
 DCIM-PS2

264
DCIM-USB
Target server

Windows XP

Windows 2000

Windows 2000
Server

Windows 2003
Server

Windows Vista

Windows 7

Windows 2008

Red Hat Enterprise
Linux 4 ES

Red Hat Enterprise
Linux 5

Open SUSE 10, 11

Fedora Core 3
and above

IBM AIX

HP UX

Windows XP

Windows 2000

Windows 2000
Server

Windows 2003
Server

Windows Vista

Windows 7

Windows 2008

Red Hat Enterprise
Linux 4 ES

Red Hat Enterprise
Linux 5

Open SUSE 10, 11

Fedora 8 - 11

Mac OS

IBM AIX

HP UX
Virtual
media
Absolute
Intelligent
Standard
Mouse mode Mouse mode Mouse
mode
Appendix A: Specifications
Supported
Dominion KX I
DCIMs
 DCIM-USBG2
Target server

Windows XP

Windows 2000

Windows 2000
Server

Windows 2003
Server

Windows Vista

Windows 7

Windows 2008

Red Hat Enterprise
Linux 4 ES

Red Hat Enterprise
Linux 5

Open SUSE 10, 11

Fedora 8 - 11

Mac OS

All Solaris OSs
supported in
Dominion KX I

IBM AIX

HP UX
Virtual
media
Absolute
Intelligent
Standard
Mouse mode Mouse mode Mouse
mode
Note: The DCIM-USBG2 and P2CIM-AUSB provide a small slide switch on the back of the CIM. Move
the switch to P for PC-based USB target servers; move the switch to S for Sun USB target servers. A
new switch position takes effect only after the CIM is power-cycled. To power-cycle the CIM, remove the
USB connector from the target server and plug it back in a few seconds later.

DCIM-SUN

DCIM-SUSB

All Solaris OSs
supported in
Dominion KX I
265
Appendix A: Specifications
Supported
Dominion KX II
D2CIMs
 D2CIM-VUSB
Target server and
remote power strips
(where applicable)
 Windows XP

Windows 2000

Windows 2000
Server

Windows 2003
Server

Windows Vista

Windows 7

Windows 2008

Open SUSE 10, 11

Fedora Core 3
and above

Red Hat Enterprise
Linux 4 ES

Red Hat Enterprise
Linux 5

Mac OS
Virtual
media
Absolute
Mouse mode
Note: D2CIM-VUSB is not supported on Sun™ (Solaris) targets.
*The Linux OS does not support Absolute Mouse mode.


266
D2CIM-DVUSB
D2CIM-PWR

Windows XP

Windows 2000

Windows 2000
Server

Windows 2003
Server

Windows Vista

Windows 7

Windows 2008

Open SUSE 10, 11

Fedora 8 - 11

Mac OS

Remote power strips
*
Intelligent
Mouse
mode
Standard
Mouse
mode
Appendix A: Specifications
Supported Paragon CIMS and Configurations
The Dominion KX II supports the P2CIM-APS2DUAL and
P2CIM-AUSBDUAL CIMs, which provide two RJ45 connections to
different KVM switches. Support of these CIMs provides a second path
to access the target in the event that one of the KVM switches is blocked
or fails.
Paragon CIM
Supports
Does not support
 Virtual media
P2CIM-APS2DUA  Servers with IBM®
PS/2-type keyboard  Smart cards
L
and mouse ports
 Absolute Mouse mode
 Automatic skew
 Use with blade chassis
compensation
(when the CIMs are  Cascaded KVM
connected to
configurations
Paragon II, not
from a Dominion
KX II)

Intelligent Mouse
mode

Standard Mouse
mode
P2CIM-AUSBDUA 
L


Virtual media

Smart cards

Absolute Mouse mode

Automatic skew
compensation

(when the CIMs are
connected to
Paragon II, not
from a Dominion
KX II)
Use with blade chassis
Servers with USBor Sun™ USB-type
keyboard and
mouse ports

Intelligent Mouse
mode

Standard Mouse
mode
Cascaded KVM
configurations
267
Appendix A: Specifications
Dominion KX II to Dominion KX II Guidelines
The following system configuration guidelines should be followed when
you are using Paragon CIMs in a Dominion KX II to Dominion KX II
configuration:
Concurrent Access
Concurrent access guarantees that concurrent access to targets is
prohibited for all targets by all user groups.

Both Dominion KX II KVM switches should be configured with the
same policy for concurrent access to targets.

If Private access to targets is required, both KVM switches must
have PC Share Mode set to Private. See Encryption & Share (on
page 197).
Note: User Group PC Share permissions must not be relied on if privacy
must be guaranteed when using the P2CIM-APS2DUAL or
P2CIM-AUSBDUAL with the Dominion KX II.
CIM Name Updates
The P2CIM-APS2 and P2CIM-AUSB names are stored within the CIM‟s
memory. There are two memory locations provided to accommodate
the Paragon naming convention (12 characters) and the Dominion KX II
naming convention (32 characters).
When first connected to a Dominion KX II, the Paragon name will be
retrieved from memory and written into the CIM memory location used by
Dominion KX II. Subsequent queries for the CIM name or updates to the
CIM name from the Dominion KX II will be made to the memory location
used by the Dominion KX II. Updates will not be made by the Dominion
KX II to the memory location used by Paragon II.
When the CIM name is updated by one Dominion KX II, the other
Dominion KX II will detect and retrieve the updated name on the next
attempt to connect to that target. Until that time, the name will not be
updated on the other Dominion KX II.
Port Status and Availability
The port status, displayed on the Dominion KX II Port Access page as
either Up or Down, is updated to show whether the CIM is powered up
and connected to the Dominion KX II port.
The port availability, as displayed on the Dominion KX II Port Access
page as Idle, Busy or Connected, is only updated to reflect activity on a
target that has been initiated from that same Dominion KX II.
268
Appendix A: Specifications
If a connection to the target is in place from the other Dominion KX II, the
availability is checked when a connection is attempted. Access is denied
or allowed consistent with the PC-Share policy in place for the Dominion
KX II. Until that time, the availability is not be updated on the other
Dominion KX II.
If access is denied because the target is busy, a notification is displayed.
Working from CC-SG
Operations initiated from CC-SG are based on the Status, Availability
and CIM name reported by the managed Dominion KX II. When the
target is connected to two managed Dominion KX IIs and the devices are
added to CC-SG, two nodes will be created. Each node will have its own
oob-kvm interface associated with it. Alternatively, a single node can be
configured with an oob-kvm interface from each Dominion KX II.
If the Dominion KX IIs are configured for „Private‟ mode, when a second
connection is attempted the user is notified that they cannot connect and
access is denied.
When a port name change is initiated via the CC-SG Port Profile pane,
the changed name is pushed to the managed Dominion KX II. The
corresponding port name of the other Dominion KX II will not be updated
in CC-SG until a connection is attempted to the target port via the other
Dominion KX II‟s oob-kvm interface.
Dominion KX II to Paragon II Guidelines
The P2CIM-APS2DUAL or P2CIM-AUSBDUAL can be connected to a
Dominion KX II and Paragon II.
Concurrent Access
Both the Dominion KX II and Paragon II must be configured with the
same policy for concurrent access to targets.
Paragon II
operation
mode
Private
Mode description
Supported?
A server or other device
on a specific channel
port can be accessed
exclusively by only one
user at a time.
Supported.
Both Paragon II and the
Dominion KX II must be set
to Private. The Private
setting is applied on to
Dominion KX II device, not
per user group.
The Paragon II uses Red to
indicate „busy‟ or Green to
269
Appendix A: Specifications
Paragon II
operation
mode
Mode description
Supported?
indicate „available‟.
PC Share
A server or other device
on a specific channel
port can be selected and
controlled by more than
one user, but only one
user has keyboard and
mouse control at any
one time.
Supported.
However, PC Share Idle
Timeout, which is configured
on the Paragon II, is not
supported. Both users will
have concurrent keyboard
and mouse control.
The Paragon II uses Green
to indicate „available‟. This
will also be true if another
user is already accessing
the target.
Public View
While one user is
accessing a server or
other device on a
specific channel port,
other users can select
that channel port and
view the video output
from that device.
However, only the first
user will have keyboard
and mouse control until
they disconnect or
switch away.
Not supported.
This mode cannot be used
when connecting the CIM to
a Paragon II and the
Dominion KX II.
The Paragon II uses Yellow
to indicate it is in P-View
mode.
CIM Name Updates
270

CIM names updated from Paragon II are stored and retrieved from
the CIM memory location corresponding to the Paragon naming
convention.

CIM names updated from the Dominion KX II are stored and
retrieved from the CIM memory location corresponding to the
Dominion KX II naming convention.

CIM name updates do not propagate between the Paragon II and the
Dominion KX II.
Appendix A: Specifications
Supported Operating Systems (Clients)
The following operating systems are supported on the Virtual KVM Client
and Multi-Platform Client (MPC):
Client operating system
Windows 7
Virtual media (VM) support on client
®
Yes
®
Windows XP
Yes
Windows 2008®
Yes
®
Yes
Windows Vista
Windows 2000 SP4® Server
Yes
®
Windows 2003 Server
Yes
Windows 2008® Server
Yes
Red Hat® Desktop 5.0
Yes. Locally held ISO image, Remote
File Server mounting directly from
Dominion KX II.
Red Hat Desktop 4.0
Yes. Locally held ISO image, Remote
File Server mounting directly from
Dominion KX II.
Open SUSE 10, 11
Yes. Locally held ISO image, Remote
File Server mounting directly from
Dominion KX II.
Fedora® 8 - 11
Yes. Locally held ISO image, Remote
File Server mounting directly from
Dominion KX II.
Mac® OS
No
Solaris
™
No
The JRE™ plug-in is available for the Windows® 32-bit and 64-bit
operating systems. MPC and VKC can be launched only from a 32-bit
browser, or 64-bit IE7 or IE8 browser.
Following are the Java™ 32-bit and 64-bit Windows operating system
requirements.
Mode
Windows x64
32-bit mode
Operating system
®
Windows XP
Browser
 Internet Explorer® 6.0
SP1+ or 7.0, IE 8

Mozilla® 1.4.X or 1.7+

Netscape® 7.X

Firefox® 1.06 - 3
271
Appendix A: Specifications
Mode
Operating system
Windows Server 2003
Windows Vista
®
Windows 7®
Windows XP
Windows x64
64-bit mode
Windows XP
Professional®
Windows XP Tablet®
Windows Vista
Windows Server 2003
Windows Server 2008
Windows 7
®
Browser
 Internet Explorer 6.0
SP1++, IE 7, IE 8

Mozilla 1.4.X or 1.7+

Netscape 7.X

Firefox 1.06 - 3

Internet Explorer 7.0 or
8.0

Internet Explorer 7.0 or
8.0

Firefox 1.06 - 3
64bit OS, 32bit browsers:

Internet Explorer 6.0
SP1+, 7.0 or 8.0

Mozilla 1.4.X or 1.7+

Netscape 7.X

Firefox 1.06 - 3
64bit mode, 64bit browsers:

Internet Explorer 7.0 or
8.0
Supported Browsers
Dominion KX II supports the following browsers:

Internet Explorer® 6, 7 and 8

Firefox® 1.5, 2.0, and 3.0 (up to build 3.0.10)

Mozilla® 1.7

Safari® 2.0

USRobotics® 56K 5686E

ZOOM® v90

ZOOM v92

USRobotics Sportster® 56K

USRobotics Courier™ 56K
Certified Modems
272
Appendix A: Specifications
Devices Supported by the KX2-832 and KX2-864 Extended Local Port
The extended local port supports attachment from the following devices:

KX2-832 and KX2-864.

Paragon II User Station (P2-UST) connected directly to extended
local port.

Paragon II Enhanced User Station (P2-EUST) connected directly to
extended local port.

Cat5Reach URKVMG Receiver connected directly to extended local
port.

Paragon II analog KVM switch (UMT) target port connected to
extended local port. Provides furthest possible access to extended
local port, when used together with the Paragon II Enhanced User
Station.
Target Server Connection Distance and Video Resolution
The maximum supported distance is a function of many factors including
the type/quality of Cat5 cable, server type and manufacturer, video driver
and monitor, environmental conditions, and user expectations. The
following table summarizes the maximum target server distance for
various video resolutions and refresh rates:
Video resolution
Refresh rate
Maximum distance
1600x1200
60
50 ft (15 m)
1280x1024
60
100 ft (30 m)
1024x768
60
150 ft (45 m)
Note: Due to the multiplicity of server manufacturers and types, OS
versions, video drivers, and so forth and the subjective nature of video
quality, Raritan cannot guarantee performance across all distances in all
environments.
See the Supported Video Resolutions (on page 274) for the video
resolutions supported by the Dominion KX II.
KX2-832 and KX2-864 Extended Local Port Recommended Maximum
Distances
Extended device
1024x768, 60 Hz
1280x1024, 60 Hz
Paragon II UMT using
1000
900
273
Appendix A: Specifications
EUST
Paragon EUST
500
400
URKVM
650
250
Paragon UST
500
200
Remote Connection
Remote
connection
Details
Network
10BASE-T, 100BASE-T, and 1000BASE-T (Gigabit)
Ethernet
Protocols
TCP/IP, UDP, SNTP, HTTP, HTTPS, RADIUS,
LDAP/LDAPS
Supported Video Resolutions
Ensure that each target server's video resolution and refresh rate are
supported by the Dominion KX II and that the signal is noninterlaced.
Video resolution and cable length are important factors in the ability to
obtain mouse synchronization. See Target Server Connection
Distance and Video Resolution (on page 273).
The Dominion KX II supports these resolutions:
Resolutions
640x350 @70Hz
1024x768 @75Hz
640x350 @85Hz
1024x768 @90Hz
640x400 @56Hz
1024x768 @100Hz
640x400 @84Hz
1152x864 @60Hz
640x400 @85Hz
1152x864 @70Hz
640x480 @60Hz
1152x864 @75Hz
640x480 @66.6Hz 1152x864 @85Hz
274
640x480 @72Hz
1152x870 @75.1Hz
640x480 @75Hz
1152x900 @66Hz
640x480 @85Hz
1152x900 @76Hz
720x400 @70Hz
1280x720@60Hz
Appendix A: Specifications
Resolutions
720x400 @84Hz
1280x960 @60Hz
720x400 @85Hz
1280x960 @85Hz
800x600 @56Hz
1280x1024 @60Hz
800x600 @60Hz
1280x1024 @75Hz
800x600 @70Hz
1280x1024 @85Hz
800x600 @72Hz
1360x768@60Hz
800x600 @75Hz
1366x768@60Hz
800x600 @85Hz
1368x768@60Hz
800x600 @90Hz
1400x1050@60Hz
800x600 @100Hz 1440x900@60Hz
832x624 @75.1Hz 1600x1200 @60Hz
1024x768 @60Hz 1680x1050@60Hz
Note: Composite Sync and Sync-on-Green video require an additional
adapter.
Note: Some resolutions may not be available by default. If you do not
see a resolution, plug in the monitor first, remove the monitor and then
plug in the CIM.
Note: If the 1440x900 and 1680x1050 resolutions are not displayed but
are supported by the target server's graphics adapter card, a DDC-1440
or DDC-1680 adapter may be required.
Supported Keyboard Languages
The Dominion KX II provides keyboard support for the languages listed
in the following table.
Note: You can use the keyboard for Chinese, Japanese, and Korean for
display only; local language input is not supported at this time for the
Dominion KX II Local Console functions. For more information about
non-US keyboards, see Informational Notes (on page 291).
Note: Raritan strongly recommends that you use system-config-keyboard
to change languages if you are working in a Linux environment.
Language
Regions
Keyboard layout
US English
United States of America and
most of English-speaking
countries: for example, Canada,
Australia, and New Zealand.
US Keyboard layout
275
Appendix A: Specifications
Language
Regions
Keyboard layout
US English
International
United States of America and
most of English-speaking
countries: for example,
Netherlands
US Keyboard layout
UK English
United Kingdom
UK layout keyboard
Chinese
Traditional
Hong Kong S. A. R., Republic of
China (Taiwan)
Chinese Traditional
Chinese
Simplified
Mainland of the People‟s
Republic of China
Chinese Simplified
Korean
South Korea
Dubeolsik Hangul
Japanese
Japan
JIS Keyboard
French
France
French (AZERTY)
layout keyboard.
German
Germany and Austria
German keyboard
(QWERTZ layout)
Belgian
Belgium
Belgian
Norwegian
Norway
Norwegian
Danish
Denmark
Danish
Swedish
Sweden
Swedish
Hungarian
Hungary
Hungarian
Slovenian
Slovenia
Slovenian
Italian
Italy
Italian
Spanish
Spain and most Spanish
speaking countries
Spanish
Portuguese
Portugal
Portuguese
Smart Card Readers
Supported and Unsupported Smart Card Readers
Only USB type external smart card readers are supported by the KX II.
Supported Smart Card Readers
276
Appendix A: Specifications
Type
Vendor
Model
Verified
USB
SCM
Microsystems
SCR331
Verified on local
and remote
USB
ActivIdentity®
ActivIdentity USB
Reader v2.0
Verified on local
and remote
USB
ActivIdentity
ActivIdentity USB
Reader v3.0
Verified on local
and remote
USB
Gemalto®
GemPC USB-SW
Verified on local
and remote
USB
Keyboard/Card
reader Combo
Dell®
USB Smart Card
Reader Keyboard
Verified on local
and remote
USB
Keyboard/Card
reader Combo
Cherry GmbH
G83-6744
SmartBoard
Verified on local
and remote
USB reader for Omnikey
SIM-sized cards
6121
Verified on local
and remote
Integrated (Dell
Latitude D620)
O2Micro
OZ776
Remote only
PCMCIA
ActivIdentity
ActivIdentity
PCMCIA Reader
Remote only
PCMCIA
SCM
Microsystems
SCR243
Remote only
Note: SCM Microsystems SCR331 smart card readers must be using
SCM Microsystems firmware v5.25.
Unsupported Smart Card Readers
This table contains a list of readers that Raritan has tested with the KX II
and we know not to work, therefore they are unsupported. If a smart card
reader does not appear in the supported smart card readers table or in
the unsupported smart card readers table, Raritan cannot guarantee it
will function with the KX II.
Type
Vendor
®
Model
Notes
USB Keyboard/Card
reader Combo
HP
ED707A
No interrupt endpoint
=> not compatible with
Microsoft® driver
USB Keyboard/Card
reader Combo
SCM
Microsystems
SCR338
Proprietary card
reader implementation
(not CCID-compliant)
USB Token
Aladdin®
eToken
Proprietary
277
Appendix A: Specifications
Type
Vendor
Model
PRO™
Notes
implementation
Minimum System Requirements
Local Port Requirements
The basic interoperability requirement for local port attachment to the
Dominion KX II is:

All devices (smart card reader or token) that are locally attached
must be USB CCID-compliant.
Target Server Requirements
When using smart card readers, the basic requirements for
interoperability at the target server are:

The IFD (smart card reader) Handler must be a standard USB CCID
device driver (comparable to the generic Microsoft® USB CCID
driver).

A D2CIM-DVUSB (Dual-VM CIM) is required and must be using
firmware version 3A6E or later.

Blade chassis server connections, where a CIM per blade is used,
are supported.

Blade chassis server connections, where a CIM per chassis is used,
is only supported for IBM® BladeCenter® models H and E with
auto-discovery enabled.
Windows XP Targets
Windows XP® operating system targets must be running Windows XP
SP3 in order to use smart cards with the Dominion KX II. If you are
working with .NET 3.5 in a Windows XP environment on the target
server, you must be using SP1.
Linux Targets
If you are using a Linux® target, the following requirements must be met
to use smart card readers with the Dominion KX II.

CCID Requirements
If the Raritan D2CIM-DVUSB VM/CCID is not recognized as a smart
card reader by your Linux target, you may need to update the CCID
driver version to 1.3.8 or above and update the driver configuration
file (Info.plist).
278
Appendix A: Specifications
Operating system
CCID requirements
RHEL 5
ccid-1.3.8-1.el5
SuSE 11
pcsc-ccid-1.3.8-3.12
Fedora® Core 10
ccid-1.3.8-1.fc10.i386
Remote Client Requirements
The basic requirements for interoperability at the remote client are:

The IFD (smart card reader) Handler must be a PC/SC compliant
device driver.

The ICC (smart card) Resource Manager must be available and be
PC/SC compliant.

The JRE™ 1.6.x with smart card API must be available for use by the
Raritan client application.
Linux Clients
If you are using a Linux® client, the following requirements must be met
to use smart card readers with the Dominion KX II.
Note: User login to client, on smart card insertion, may take longer when
1 or more KVM sessions are actively in place to targets. As the login
process to these targets is also under way.

PC/SC Requirements
Operating system
RHEL 5
Required PC/SC
pcsc-lite-1.4.4-0.1.el5
SuSE 11
pcsc-lite-1.4.102-1.24
Fedora® Core 10

pcsc-lite-1.4.102.3.fc10.i386
™
Create a Java Library Link
A soft link must be created to the libpcsclite.so after upgrading RHEL
4, RHEL 5 and FC 10. For example, ln –s /usr/lib/libpcsclite.so.1
/usr/lib/libpcsclite.so, assuming installing the package places the
libraries in /usr/lib or /user/local/lib.

PC/SC Daemon
When the pcsc daemon (resource manager in framework) is
restarted, restart the browser and MPC, too.
TCP and UDP Ports Used
279
Appendix A: Specifications
Port
Description
HTTP, Port 80
This port can be configured as needed. See HTTP and HTTPS Port
Settings (on page 138). By default, all requests received by the
Dominion KX II via HTTP (port 80) are automatically forwarded to
HTTPS for complete security. The Dominion KX II responds to Port 80
for user convenience, relieving users from having to explicitly type in
the URL field to access the Dominion KX II, while still preserving
complete security.
HTTPS, Port 443
This port can be configured as needed. See HTTP and HTTPS Port
Settings (on page 138). By default, this port is used for multiple
purposes, including the web server for the HTML client, the download
of client software (MPC/VKC) onto the client's host, and the transfer of
KVM and virtual media data streams to the client.
Dominion KX II
(Raritan
KVM-over-IP)
Protocol,
Configurable Port
5000
This port is used to discover other Dominion devices and for
communication between Raritan devices and systems, including
CC-SG. By default, this is set to Port 5000, but you may configure it to
use any TCP port not currently in use. For details on how to configure
this setting, see Network Settings.
SNTP (Time Server) The Dominion KX II offers the optional capability to synchronize its
on Configurable
internal clock to a central time server. This function requires the use of
UDP Port 123
UDP Port 123 (the standard for SNTP), but can also be configured to
use any port of your designation. Optional
LDAP/LDAPS on
Configurable Ports
389 or 636
If the Dominion KX II is configured to remotely authenticate user logons
via the LDAP/LDAPS protocol, ports 389 or 636 will be used, but the
system can also be configured to use any port of your designation.
Optional
RADIUS on
Configurable Port
1812
If the Dominion KX II is configured to remotely authenticate user logons
via the RADIUS protocol, either port 1812 will be used, but the system
can also be configured to use any port of your designation. Optional
RADIUS Accounting If the Dominion KX II is configured to remotely authenticate user logons
on Configurable Port via the RADIUS protocol, and also employs RADIUS accounting for
1813
event logging, port 1813 or an additional port of your designation will be
used to transfer log notifications.
SYSLOG on
Configurable UDP
Port 514
If the Dominion KX II is configured to send messages to a Syslog
server, then the indicated port(s) will be used for communication - uses
UDP Port 514.
SNMP Default UDP
Ports
Port 161 is used for inbound/outbound read/write SNMP access and
port 162 is used for outbound traffic for SNMP traps. Optional
TCP Port 21
Port 21 is used for the Dominion KX II command line interface (when
you are working with Raritan Technical Support).
280
Appendix A: Specifications
Network Speed Settings
Dominion KX II network speed setting
Network
switch port
setting
Auto
Auto
Highest
Available
Speed
1000/Full
1000/Full
100/Full
Dominion
KX II:
100/Full
100/Half
100/Half
Switch:
100/Half
1000/Full
100/Full
100/Half
10/Full
Dominion
KX II:
10/Full
10/Half
10/Half
Switch:
10/Half
1000/Full
1000/Full
No
No
No
No
Communica Communicat Communica Communicat
tion
ion
tion
ion
Dominion
KX II:
100/Half
Dominion
KX II:
100/Half
100/Full
Switch:
100/Full
Switch:
100/Full
100/Half
100/Half
Dominion
KX II:
100/Half
No
No
Communica Communicat
tion
ion
Switch:
100/Full
Dominion
KX II:
100/Full
100/Half
No
No
Communica Communicat
tion
ion
Switch:
100/Half
10/Full
Dominion
KX II:
10/Half
No
No
No
10/Full
Communica Communica Communicat
tion
tion
ion
Switch:
10/Full
10/Half
10/Half
Dominion
KX II:
10/Half
Switch:
10/Full
No
No
No
Dominion
Communica Communica Communicat KX II:
tion
tion
ion
10/Full
10/Half
Switch:
10/Half
Legend:
Does not function as expected
Supported
281
Appendix A: Specifications
Functions; not recommended
NOT supported by Ethernet specification; product will
communicate, but collisions will occur
Per Ethernet specification, these should be “no
communication,” however, note that the Dominion KX II
behavior deviates from expected behavior
Note: For reliable network communication, configure the Dominion KX II
and the LAN switch to the same LAN Interface Speed and Duplex. For
example, configure both the Dominion KX II and LAN Switch to
Autodetect (recommended) or set both to a fixed speed/duplex such as
100MB/s/Full.
282
Appendix B Updating the LDAP Schema
Note: The procedures in this chapter should be attempted only by
experienced users.
In This Chapter
Returning User Group Information ........................................................283
Setting the Registry to Permit Write Operations to the Schema ...........284
Creating a New Attribute .......................................................................284
Adding Attributes to the Class ...............................................................285
Updating the Schema Cache.................................................................287
Editing rciusergroup Attributes for User Members ................................287
Returning User Group Information
Use the information in this section to return User Group information (and
assist with authorization) once authentication is successful.
From LDAP
When an LDAP/LDAPS authentication is successful, the Dominion KX II
determines the permissions for a given user based on the permissions of
the user's group. Your remote LDAP server can provide these user group
names by returning an attribute named as follows:
rciusergroup
attribute type: string
This may require a schema extension on your LDAP/LDAPS server.
Consult your authentication server administrator to enable this attribute.
From Microsoft Active Directory
Note: This should be attempted only by an experienced Active Directory®
administrator.
Returning user group information from Microsoft's® Active Directory for
Windows 2000® server requires updating the LDAP/LDAPS schema. See
your Microsoft documentation for details.
1. Install the schema plug-in for Active Directory. See Microsoft Active
Directory documentation for instructions.
2. Run Active Directory Console and select Active Directory Schema.
283
Appendix B: Updating the LDAP Schema
Setting the Registry to Permit Write Operations to the Schema
To allow a domain controller to write to the schema, you must set a
registry entry that permits schema updates.
To permit write operations to the schema:
1. Right-click the Active Directory® Schema root node in the left pane of
the window and then click Operations Master. The Change Schema
Master dialog appears.
2. Select the "Schema can be modified on this Domain Controller"
checkbox. Optional
3. Click OK.
Creating a New Attribute
To create new attributes for the rciusergroup class:
1. Click the + symbol before Active Directory® Schema in the left pane
of the window.
2. Right-click Attributes in the left pane.
284
Appendix B: Updating the LDAP Schema
3. Click New and then choose Attribute. When the warning message
appears, click Continue and the Create New Attribute dialog
appears.
4. Type rciusergroup in the Common Name field.
5. Type rciusergroup in the LDAP Display Name field.
6. Type 1.3.6.1.4.1.13742.50 in the Unique x5000 Object ID field.
7. Type a meaningful description in the Description field.
8. Click the Syntax drop-down arrow and choose Case Insensitive
String from the list.
9. Type 1 in the Minimum field.
10. Type 24 in the Maximum field.
11. Click OK to create the new attribute.
Adding Attributes to the Class
To add attributes to the class:
1. Click Classes in the left pane of the window.
285
Appendix B: Updating the LDAP Schema
2. Scroll to the user class in the right pane and right-click it.
3. Choose Properties from the menu. The user Properties dialog
appears.
4. Click the Attributes tab to open it.
5. Click Add.
286
Appendix B: Updating the LDAP Schema
6. Choose rciusergroup from the Select Schema Object list.
7. Click OK in the Select Schema Object dialog.
8. Click OK in the User Properties dialog.
Updating the Schema Cache
To update the schema cache:
1. Right-click Active Directory® Schema in the left pane of the window
and select Reload the Schema.
2. Minimize the Active Directory Schema MMC (Microsoft®
Management Console) console.
Editing rciusergroup Attributes for User Members
To run the Active Directory® script on Windows 2003® server, use the
script provided by Microsoft® (available on the Windows 2003 server
installation CD). These scripts are loaded onto your system with a
Microsoft Windows 2003 installation. ADSI (Active Directory Service
Interface) acts as a low-level editor for Active Directory, allowing you to
perform common administrative tasks such as adding, deleting, and
moving objects with a directory service.
To edit the individual user attributes within the group
rciusergroup:
1. From the installation CD, choose Support > Tools.
2. Double-click SUPTOOLS.MSI to install the support tools.
287
Appendix B: Updating the LDAP Schema
3. Go to the directory where the support tools were installed. Run
adsiedit.msc. The ADSI Edit window opens.
4. Open the Domain.
288
Appendix B: Updating the LDAP Schema
5. In the left pane of the window, select the CN=Users folder.
6. Locate the user name whose properties you want to adjust in the
right pane. Right-click the user name and select Properties.
289
Appendix B: Updating the LDAP Schema
7. Click the Attribute Editor tab if it is not already open. Choose
rciusergroup from the Attributes list.
8. Click Edit. The String Attribute Editor dialog appears.
9. Type the user group (created in the Dominion KX II) in the Edit
Attribute field. Click OK.
290
Appendix C Informational Notes
In This Chapter
Overview ................................................................................................291
Java Runtime Environment (JRE) .........................................................291
IPv6 Support Notes ...............................................................................292
Keyboards .............................................................................................293
Mouse Pointer Synchronization (Fedora) ..............................................296
Dell Chassis Cable Lengths and Video Resolutions .............................296
Fedora ...................................................................................................297
Video Modes and Resolutions ...............................................................297
USB Ports and Profiles ..........................................................................298
CIMs ......................................................................................................300
Virtual Media ..........................................................................................301
CC-SG ...................................................................................................302
Overview
This section includes important notes on Dominion KX II usage. Future
updates will be documented and available online through the Help link in
the Dominion KX II Remote Console interface.
Java Runtime Environment (JRE)
Important: It is recommended that you disable Java™ caching and
clear the Java cache. Please refer to your Java documentation or
the KVM and Serial Access Clients Guide for more information.
The Dominion KX II Remote Console and MPC require the Java Runtime
Environment™ (JRE) to function. The Dominion KX II Remote Console
checks the Java version. If the version is incorrect or outdated, you will
be prompted to download a compatible version.
Raritan recommends using JRE version 1.6 for optimum performance,
but the Dominion KX II Remote Console and MPC will function with JRE
version 1.6.x and higher with the exception of 1.6.2.
Note: In order for multi-language keyboards to work in the Dominion KX
II Remote Console (Virtual KVM Client), install the multi-language
version of JRE.
291
Appendix C: Informational Notes
IPv6 Support Notes
Java
Java™ 1.6 supports IPv6 for the following:

Solaris™ 8 and higher

Linux® kernel 2.1.2 and higher (RedHat 6.1 and higher)
Java 5.0 and above supports the IPv6 for the following:

Solaris 8 and higher

Linux kernel 2.1.2 and higher (kernel 2.4.0 and higher recommended
for better IPv6 support)

Windows XP® SP1 and Windows 2003®, Windows Vista® operating
systems
The following IPv6 configurations are not supported by Java:

J2SE 1.4 does not support IPv6 on Microsoft® Windows®.
Linux

It is recommended that Linux kernel 2.4.0 or higher is used when
using IPv6.

An IPv6-enabled kernel will need to be installed or the kernel will
need to be rebuilt with IPv6 options enabled.

Several network utilities will also need to be installed for Linux when
using IPv6. For detailed information, refer to
http://www.bieringer.de/linux/IPv6/IPv6-HOWTO/IPv6-HOWTO.html
Windows

Windows XP and Windows 2003 users will need to install the
Microsoft IPV6 service pack to enable IPV6.
Mac Leopard

IPv6 is not supported in Dominion KX II version 2.0.20 for Mac®
Leopard®.
Samba

292
IPv6 is not supported for use with virtual media when using Samba.
Appendix C: Informational Notes
Keyboards
Non-US Keyboards
French Keyboard
Caret Symbol (Linux® Clients Only)
The Virtual KVM Client and the Multi-Platform Client (MPC) do not
process the key combination of Alt Gr + 9 as the caret symbol (^) when
using French keyboards with Linux clients.
To obtain the caret symbol:
From a French keyboard, press the ^ key (to the right of the P key), then
immediately press the space bar.
Alternatively, create a macro consisting of the following commands:
1. Press Right Alt
2. Press 9.
3. Release 9.
4. Release Right Alt.
Note: These procedures do not apply to the circumflex accent (above
vowels). In all cases, the ^ key (to the right of the P key) works on French
keyboards to create the circumflex accent when used in combination with
another character.
Accent Symbol (Windows XP® Operating System Clients Only)
From the Virtual KVM Client and the Multi-Platform Client, the key
combination of Alt Gr + 7 results in the accented character displaying
twice when using French keyboards with Windows XP clients.
Note: This does not occur with Linux clients.
Numeric Keypad
From the Virtual KVM Client and the Multi-Platform Client, the numeric
keypad symbols display as follows when using a French keyboard:
Numeric keypad symbol
Displays as
/
;
.
;
293
Appendix C: Informational Notes
Tilde Symbol
From the Virtual KVM Client and the Multi-Platform Client, the key
combination of Alt Gr + 2 does not produce the tilde (~) symbol when
using a French keyboard.
To obtain the tilde symbol:
Create a macro consisting of the following commands:

Press right Alt.

Press 2.

Release 2.

Release right Alt.
Keyboard Language Preference (Fedora Linux Clients)
Because the Sun™ JRE™ on Linux® has problems generating the correct
KeyEvents for foreign-language keyboards configured using System
Preferences, Raritan recommends that you configure foreign keyboards
using the methods described in the following table.
294
Language
Configuration method
US Intl
Default
UK
System Settings (Control Center)
French
Keyboard Indicator
German
Keyboard Indicator
Hungarian
System Settings (Control Center)
Spanish
System Settings (Control Center)
Swiss-German
System Settings (Control Center)
Norwegian
Keyboard Indicator
Swedish
Keyboard Indicator
Danish
Keyboard Indicator
Japanese
System Settings (Control Center)
Korean
System Settings (Control Center)
Slovenian
System Settings (Control Center)
Italian
System Settings (Control Center)
Portuguese
System Settings (Control Center)
Appendix C: Informational Notes
Note: The Keyboard Indicator should be used on Linux systems using
Gnome as a desktop environment.
When using a Hungarian keyboard from a Linux client, the Latin letter U
with Double Acute and the Latin letter O with Double Acute work only
with JRE 1.6.
There are several methods that can be used to set the keyboard
language preference on Fedora® Linux clients. The following method
must be used in order for the keys to be mapped correctly from the
Virtual KVM Client and the Multi-Platform Client (MPC).
To set the keyboard language using System Settings:
1. From the toolbar, choose System > Preferences > Keyboard.
2. Open the Layouts tab.
3. Add or select the appropriate language.
4. Click Close.
To set the keyboard language using the Keyboard Indicator:
1. Right-click the Task Bar and choose Add to Panel.
2. In the Add to Panel dialog, right-click the Keyboard Indicator and
from the menu choose Open Keyboard Preferences.
3. In the Keyboard Preferences dialog, click the Layouts tab.
4. Add and remove languages as necessary.
Macintosh Keyboard
When a Macintosh® is used as the client, the following keys on the Mac®
keyboard are not captured by the Java™ Runtime Environment (JRE™):

F9

F10

F11

F14

F15

Volume Up

Volume Down

Mute

Eject
As a result, the Virtual KVM Client and the Multi-Platform Client (MPC)
are unable to process these keys from a Mac client's keyboard.
295
Appendix C: Informational Notes
Mouse Pointer Synchronization (Fedora)
When connected in dual mouse mode to a target server running Fedora®
7, the target and local mouse pointers may lose synchronization after
some time.
To resynchronize the mouse cursors:

Use the Synchronize Mouse option from the Virtual KVM Client.
The following table summarizes the Dominion KX II mouse modes, and
whether or not these modes remain synchronized when accessing KVM
target servers running Fedora:
Mouse mode
Fedora Core 5
Fedora Core 6
Absolute Mouse
Synchronization
No
No
Intelligent Mouse mode
No
Yes
Standard Mouse mode
Yes
No
Dell Chassis Cable Lengths and Video Resolutions
In order to maintain video quality, Raritan recommends using the
following cable lengths and video resolutions when you are connecting to
Dell® blade chassis from the Dominion KX II:
296
Cable length
Video resolution
50 ft.
1024x768x60
50 ft.
1280x1024x60
30 ft.
1600x1200x60
Appendix C: Informational Notes
Fedora
Resolving Fedora Core Focus
Using the Multi-Platform Client (MPC), occasionally there is an inability to
log in to a Dominion KX II device or to access KVM target servers
(Windows®, SUSE, and so forth). In addition, the Ctrl+Alt+M key
combination may not bring up the Keyboard Shortcut menu. This
situation occurs with the following client configuration: Fedora® Core 6
and Firefox® 1.5 or 2.0.
Through testing, it has been determined that installation of libXp resolves
window focusing issues with Fedora Core 6. Raritan has tested with
libXp-1.0.0.8.i386.rpm; this resolved all of the keyboard focus and
popup-menu problems.
Note: libXp is also required for the SeaMonkey (formerly Mozilla®)
browser to work with the Java™ plug in.
VKC and MPC Smart Card Connections to Fedora Servers
If you are using a smart card to connect to a Fedora® server via MPC or
VKC and you remove the smart card once you are connected, the
pcsc-lite library on FC7 and FC8 servers is not released and you must
restart the pcscd daemon to release it. To avoid this, upgrade the
pcsc-lite library to 1.4.102-3 or above.
Resolving Issues with Firefox Freezing when Using Fedora
If you are accessing Firefox® and are using a Fedora® server, Firefox
may freeze when it is opening. To resolve this issue, install the
libnpjp2.so Java™ plug-in on the server.
Video Modes and Resolutions
SUSE/VESA Video Modes
The SuSE X.org configuration tool SaX2 generates video modes using
modeline entries in the X.org configuration file. These video modes do
not correspond exactly with VESA video mode timing (even when a
VESA monitor is selected). The Dominion KX II, on the other hand, relies
on exact VESA mode timing for proper synchronization. This disparity
can result in black borders, missing sections of the picture, and noise.
To configure the SUSE video display:
1. The generated configuration file /etc/X11/xorg.conf includes a
Monitor section with an option named UseModes. For example,
UseModes "Modes[0]"
297
Appendix C: Informational Notes
2. Either comment out this line (using #) or delete it completely.
3. Restart the X server.
With this change, the internal video mode timing from the X server will be
used and will correspond exactly with the VESA video mode timing,
resulting in the proper video display on the Dominion KX II.
Supported Video Resolutions Not Displaying
When using a CIM, there are some video resolutions, as listed in
Supported Video Resolutions (on page 274), that may not be available
to you for selection by default.
To view all available video resolutions if they do not appear:
1. Plug the monitor in.
2. Next, unplug the monitor and plug in the CIM. All video resolutions
will not be available and can be used.
USB Ports and Profiles
VM-CIMs and DL360 USB Ports
HP® DL360 servers have one USB port on the back of the device and
another on the front of the device. With the DL360, both ports cannot be
used at the same time. Therefore, a dual VM-CIM cannot be used on
DL360 servers.
However, as a workaround, a USB2 hub can be attached to the USB port
on the back of the device and a dual VM-CIM can be attached to the
hub.
Help for Choosing USB Profiles
When you are connected to a KVM target server in VKC, you can view
information about USB profiles via the Help on USB Profiles command
on the USB Profile menu.
298
Appendix C: Informational Notes
USB profile help appears in the USB Profile Help window. For detailed
information about specific USB profiles, see Available USB Profiles (on
page 101).
Raritan provides a standard selection of USB configuration profiles for a
wide range of operating system and BIOS level server implementations.
These are intended to provide an optimal match between remote USB
device and target server configurations.
The „Generic‟ profile meets the needs of most commonly deployed target
server configurations.
Additional profiles are made available to meet the specific needs of other
commonly deployed server configurations (for example, Linux®, MAC
OS-X®).
There are also a number of profiles (designated by platform name and
BIOS revision) that have been tailored to enhance the virtual media
function compatibility with the target server, for example, when operating
at the BIOS level.
„Add Other Profiles‟ provides access to other profiles available on the
system. Profiles selected from this list will be added to the USB Profile
Menu. This includes a set of „trouble-shooting‟ profiles intended to help
identify configuration limitations.
The USB Profile Menu selections are configurable via the Console
Device Settings > Port Configuration page.
Should none of the standard USB profiles provided by Raritan meet your
target server requirements, Raritan Technical Support can work with you
to arrive at a solution tailored for that target. Raritan recommends that
you do the following:
1. Check the most recent release notes on the Raritan website
(www.raritan.com) on the Firmware Upgrade page to see if a solution
is already available for your configuration.
2. If not, please provide the following information when contacting
Raritan Technical Support:
a. Target server information, manufacturer, model, BIOS,
manufacturer, and version.
b. The intended use (e.g. redirecting an image to reload a server‟s
operating system from CD).
299
Appendix C: Informational Notes
Changing a USB Profile when Using a Smart Card Reader
There may be certain circumstances under which you will need to
change the USB profile for a target server. For example, you may need
to change the connection speed to "Use Full Speed for Virtual Media
CIM" when the target has problems with the "High Speed USB"
connection speed.
When a profile is changed, you may receive a New Hardware Detected
message and be required to log in to the target with administrative
privileges to reinstall the USB driver. This is only likely to occur the first
few times the target sees the new settings for the USB device. Afterward,
the target will select the driver correctly.
CIMs
Windows 3-Button Mouse on Linux Targets
When using a 3-button mouse on a Windows® client connecting to a
Linux® target, the left mouse button may get mapped to the center button
of the Windows client 3-button mouse.
300
Appendix C: Informational Notes
Windows 2000 Composite USB Device Behavior for Virtual Media
The Windows 2000® operating system does not support USB composite
devices, like Raritan‟s D2CIM-VUSB, in the same manner as
non-composite USB devices.
As a result, the “Safely Remove Hardware” system tray icon does not
appear for drives mapped by the D2CIM-VUSB and a warning message
may appear when disconnecting the device. Raritan has not observed
any problems or issues from this message, however.
Raritan‟s US engineering department has developed a configuration
which supports the “Safely Remove Hardware” icon and avoids this
Windows message. This configuration requires the use of the
D2CIM-DVUSB virtual media adapter and the Troubleshooting 3 USB
Profile, which configures the D2CIM-DVUSB as a non-composite USB
device supporting a single virtual media connection. Raritan has
successfully tested this configuration in the US and Japan.
Virtual Media
Virtual Media Not Refreshed After Files Added
After a virtual media drive has been mounted, if you add a file(s) to that
drive, those files may not be immediately visible on the target server.
Disconnect and then reconnect the virtual media connection.
301
Appendix C: Informational Notes
Accessing Virtual Media on a Windows 2000 Server Using a
D2CIM-VUSB
A virtual media local drive cannot be accessed on a Windows 2000®
server using a D2CIM-VUSB.
Target BIOS Boot Time with Virtual Media
The BIOS for certain targets may take longer to boot if media is mounted
virtually at the target.
To shorten the boot time:
1. Close the Virtual KVM Client to completely release the virtual media
drives.
2. Restart the target.
Virtual Media Connection Failures Using High Speed for Virtual
Media Connections
Under certain circumstances it may be necessary to select the "Use Full
Speed for Virtual Media CIM" when a target has problems with "High
Speed USB" connections or when the target is experiencing USB
protocol errors due to signal degradation due to additional connectors
and cables (for example, a connection to a blade server via a dongle).
CC-SG
Virtual KVM Client Version Not Known from CC-SG Proxy Mode
When the Virtual KVM Client is launched from CommandCenter Secure
Gateway (CC-SG) in proxy mode, the Virtual KVM Client version is
unknown. In the About Raritan Virtual KVM Client dialog, the version is
displayed as “Version Unknown”.
Single Mouse Mode - Connecting to a Dominion KX II Target Under
CC-SG Control Via VKC Using Firefox
When using Firefox® to connect to a Dominion KX II target under CC-SG
control using DCIM-PS2 or DCIM-USBG2, if you change to Single
Mouse Mode in the Virtual KVM Client, the VKC window will no longer be
the focus window and the mouse will not respond. If this occurs, left click
on the mouse or press Alt+Tab to return the focus to the VKC window.
302
Appendix C: Informational Notes
Proxy Mode and MPC
If you are using Dominion KX II in a CC-SG configuration, do not use the
CC-SG proxy mode if you are planning to use the Multi-Platform Client
(MPC).
Moving Between Ports of the Dominion KX II
If you move a between ports of the same Dominion KX II and resume
management within one minute, CC-SG may display an error message.
If you resume management, the display will be updated.
303
Appendix D FAQs
In This Chapter
General Questions.................................................................................305
Remote Access .....................................................................................307
Universal Virtual Media..........................................................................309
USB Profiles ..........................................................................................310
Bandwidth and KVM-over-IP Performance ...........................................312
Ethernet and IP Networking ..................................................................317
IPv6 Networking ....................................................................................320
Servers ..................................................................................................322
Blade Servers ........................................................................................323
Installation .............................................................................................326
Local Port...............................................................................................328
Extended Local Port (Dominion KX2-832 and KX2-864 Models Only) .330
Power Control ........................................................................................331
Scalability...............................................................................................333
Computer Interface Modules (CIMs) .....................................................335
Security ..................................................................................................336
Smart Cards and CAC Authentication ...................................................338
Manageability ........................................................................................339
Miscellaneous ........................................................................................340
304
Appendix D: FAQs
General Questions
What is the Dominion KX II?
The Dominion KX II is a second generation digital KVM (keyboard/video/
mouse) switch that enables one, two, four or eight IT administrators to
access and control 8, 16, 32 or 64 servers over the network with
BIOS-level functionality. The Dominion KX II is completely hardware and
operating system independent. Users can troubleshoot and reconfigure
servers even when servers are down.
At the rack, the Dominion KX II provides the same functionality,
convenience, space savings, and cost savings as traditional KVM
switches. However, the Dominion KX II also integrates the industry's
highest-performing KVM-over-IP technology, allowing multiple
administrators to access server KVM consoles from any networked
workstation.
How does the Dominion KX II differ from remote control software?
When using the Dominion KX II remotely, the interface, at first glance,
may seem similar to remote control software such as pcAnywhere,
Windows Terminal Services/Remote Desktop, VNC, and so forth.
However, because the Dominion KX II is not a software but a hardware
solution, it's much more powerful. Specifically:

OS- and hardware-independent - The Dominion KX II can be used to
manage servers running many popular operating systems, including
Intel®, Sun™, PowerPC running Windows®, Linux®, Solaris™, etc.

State-Independent/Agentless - The Dominion KX II does not require
the managed server's operating system to be up and running, nor
does it require any special software to be installed on the managed
server.

Out-of-Band - Even if the managed server's own network connection
is unavailable, it can still be managed through the Dominion KX II.

BIOS-Level Access - Even if the server is hung at boot up, requires
booting to safe mode or requires system BIOS parameters to be
altered, the Dominion KX II still works flawlessly to enable these
configurations to be made.
How do the new features of the Dominion KX II compare to the KX
I?
The Dominion KX II has many new and exciting features, including virtual
media, Absolute Mouse Synchronization™, dual power, dual gigabit
Ethernet, common web-based user interfaces, next generation local port,
and more.
How do I migrate from the Dominion KX I to Dominion KX II?
305
Appendix D: FAQs
In general, customers can continue to use their existing switches for
many years. As their data centers expand, customers can purchase and
use the new Dominion KX II models. Raritan's centralized management
unit, CommandCenter Secure Gateway, and the Multi-Platform Client
(MPC) both support KX I and Dominion KX II switches seamlessly.
Will my existing KX I CIMs work with the Dominion KX II switches?
Yes, existing KX I CIMs will work with the Dominion KX II switch. In
addition, select Paragon CIMs will work with the Dominion KX II. This
provides an easy migration to the Dominion KX II from Paragon I
customers who wish to switch to KVM-over-IP. However, you may want
to consider the D2CIM-VUSB and D2CIM-DVUSB CIMs which support
Virtual Media and Absolute Mouse Synchronization.
Can the Dominion KX II be rack mounted?
Yes. The Dominion KX II ships standard with 19" rack mount brackets. It
can also be reverse rack mounted so the server ports face forward.
How large is the Dominion KX II?
The Dominion KX II is only 1U high (except KX2-864 and KX2-464,
which are 2U), fits in a standard 19" rack mount, and is only 11.4" (29
cm) deep. The Dominion KX2-832 and KX2-864 are 13.8”” (44 cm) deep.
306
Appendix D: FAQs
Remote Access
How many users can remotely access servers on each Dominion
KX II?
The Dominion KX II models offer remote connections for up to eight
users per user channel to simultaneously access and control a unique
target server. For one-channel devices like the DKX2-116, up to eight
remote users can access and control a single target server. For
two-channel devices, like the DKX2-216, up to eight users can access
and control the server on channel one and up to another eight users on
channel two. For four channel devices, up to eight users per channel, for
a total of 32 (8 x 4) users, can access and control four servers.
Likewise, for the eight channel devices, up to eight users can access a
single server, up to an overall maximum of 32 users across the 8
channels
Can two people look at the same server at the same time?
Yes, up to eight people can access and control any single server at the
same time.
Can two people access the same server, one remotely and one from
the local port?
Yes, the local port is completely independent of the remote “ports.” The
local port can access the same server using the PC-Share feature.
In order to access the Dominion KX II from a client, what hardware,
software or network configuration is required?
Because the Dominion KX II is completely web-accessible, it doesn't
require installation of proprietary software on clients used for access. An
optional installed client is available on Raritan.com and is required for
access by external modem.
The Dominion KX II can be accessed through major Web browsers,
including: Internet Explorer, Mozilla and Firefox. Dominion KX II can now
be accessed on Windows, Linux and Macintosh desktops, via Raritan‟s
new Windows Client, and the Java-based Multiplatform and Virtual KVM
Clients.
Dominion KX II administrators can perform remote management
functions, such as set passwords and security, rename servers, change
IP address and so on, using a convenient browser-based interface.
What is the file size of the Virtual KVM Client applet that is used to
access the Dominion KX II? How long does it take to retrieve?
The Virtual KVM Client applet used to access the Dominion KX II is
approximately 500KB in size. The following chart describes the
approximate time required to retrieve the Dominion KX II's applet at
different network speeds:
307
Appendix D: FAQs
Speed
100Mbps
Description
Theoretical 100Mbit network speed
Time
0.05 seconds
60Mbps
Likely practical 100Mbit network speed 0.08 seconds
10Mbps
Theoretical 10Mbit network speed
.4 seconds
6Mbps
Likely practical 10Mbit network speed
.8 seconds
512Kbps
Cable modem download speed
(typical)
8 seconds
How do I access servers connected to the Dominion KX II if the network
ever becomes unavailable?
You can access servers at-the-rack or via modem. The Dominion KX II
offers a dedicated modem port for attaching an external modem.
Do you have a Windows® client?
Yes, in Release 2.2, we have a native .NET Windows Client, which is
called the Raritan Active KVM Client.
Do you have a non-Windows client?
Yes. Both the Virtual KVM Client and the Multi-Platform Client (MPC)
allow non-Windows users to connect to KVM target servers through the
Dominion KX I and Dominion KX II switches. MPC can be run via web
browser and standalone. Refer to Virtual KVM Client and Raritan
Multi-Platform Client (MPC) Supported Operating Systems in the
KVM and Serial Client Guide for more information.
Do your KVM clients support LCD monitors?
Yes. For customers wishing to enhance their productivity by using
multiple LCD monitors on their desktops, the Dominion KX II can launch
KVM sessions to multiple monitors, either in full screen or standard
modes.
Sometimes during a Virtual KVM Client session, the Alt key appears
to get stuck. What should I do?
This usually occurs in situations when the Alt key is held and not
released. For instance, continuing to press the Alt key while pressing the
space bar might cause the focus to change from the target server to the
client PC. The local operating system then interprets this key
combination and consequently triggers the action for this key
combination in the active window (the client PC).
308
Appendix D: FAQs
Universal Virtual Media
What Dominion KX II models support virtual media?
All of the Dominion KX II models support virtual media. It is available
standalone and through Raritan's CommandCenter Secure Gateway,
Raritan's centralized management unit.
What types of virtual media does the Dominion KX II support?
The Dominion KX II supports the following types of media: internal and
USB-connected CD/DVD drives, USB mass storage devices, PC hard
drives, and ISO images.
What is required for virtual media?
A Dominion KX II virtual media CIM is required. There are two of these
CIMs: the D2CIM-VUSB and the new D2CIM-DVUSB.
The D2CIM-DVUSB has dual USB connectors and should be purchased
by customers who wish to utilize virtual media at the BIOS level. The
D2CIM-DVUSB is also required for smart card authentication.
The D2CIM-VUSB has a single USB connector and is for customers who
will use virtual media at the OS level.
Both support virtual media sessions to target servers supporting the USB
2.0 interface.
Available in economical 32 and 64 quantity CIM packages, these CIMs
support Absolute Mouse Synchronization as well as remote firmware
update.
Is virtual media secure?
Yes. Virtual media sessions are secured using AES or RC4 encryption.
309
Appendix D: FAQs
USB Profiles
What is a USB profile?
Certain servers require a specifically configured USB interface for USB
based services such as virtual media. The USB Profile tailors the
Dominion KX II‟s USB interface to the server to accommodate these
server specific characteristics.
Why would I use a USB profile?
USB Profiles are most often required at the BIOS level where there may
not be full support for the USB specification when accessing virtual
media drives.
However, profiles are sometimes used at the operating system level, for
example, for mouse synchronization for Mac® and Linux® servers.
How is a USB profile used?
Individual or groups of ports can be configured by the administrator to
use a specific USB profile in the Dominion KX II‟s Port Configuration
pages.
A USB profile can also be selected in the Dominion KX II client when
required.
What happens if I don't choose the correct USB profile?
Not choosing the right USB profile for a KVM target server can prevent a
mass storage device, mouse, or keyboard from working optimally or
working at all.
Do I always need to set a USB profile when I use virtual media?
No, in many cases, the default USB Profile is sufficient when using
virtual media at the OS level or operating at the BIOS level without
accessing virtual media.
What profiles are available?
See Available USB Profiles (on page 101).
How do I know which USB profile is best for a given target server?
The Generic profile is best for the vast majority of target servers. If this
profile does not work with a given KVM target server, you can choose the
appropriate USB profile in Available USB Profiles (on page 101). Select
the profile that best matches your target server.
What is the purpose of a BIOS profile?
310
Appendix D: FAQs
A BIOS profile has been tailored to match the requirements of a
particular server‟s BIOS that does not implement the full USB
specification. The profile enables use of keyboard, mouse, and virtual
media at the BIOS level, overcoming the restrictions or limitations of the
BIOS.
Do I need a special CIM to use USB profiles?
You must use a D2CIM-VUSB or D2CIM-DVUSB with updated firmware.
Will Raritan provide USB profiles for other target server
configurations?
Raritan will provide new USB profiles to suit customer needs. As these
profiles become available, they will be included in firmware upgrades.
311
Appendix D: FAQs
Bandwidth and KVM-over-IP Performance
How is bandwidth used in KVM-over-IP systems?
The Dominion KX II offers next generation KVM-over-IP technology – the
very best video compression available. Raritan has received numerous
technical awards confirming its high video quality transmissions and the
low bandwidth utilization.
The Dominion KX II digitizes, compresses and encrypts the keyboard,
video, and mouse signals from the target server and transmits IP packets
over the IP network to the remote client to create the remote session to
the user. The Dominion KX II provides an at-the-rack experience based
on its industry leading video processing algorithms.
Screen changes, such as video, accounts for the majority of the
bandwidth used – keyboard and mouse activity is significantly less.
It is important to note that bandwidth is only used when the user is
active. The amount of bandwidth used is based on the amount of
change to the server‟s video display screen.
If there are no changes to the video – the user is not interacting with the
server – there is generally no bandwidth used. If the user moves the
mouse or types a character, then there is a small amount of bandwidth
used. If the display is running a complex screen saver or playing a
video, then there can be a larger amount of bandwidth used.
How does bandwidth affect KVM-over-IP performance?
In general, there is a trade-off between bandwidth and performance.
The more bandwidth available, the better performance can be. In
limited bandwidth environments, performance can degrade. The
Dominion KX II has been optimized to provide strong performance in a
wide variety of environments.
What factors affect bandwidth?
There are many factors that determine how much bandwidth will be
used. The primary factor, as discussed previously, is the amount of
change in the target server‟s video display. This is dependent on the
user‟s task and actions.
Other factors include the server‟s video resolution, networking speed and
characteristics, client PC resources, and video card noise.
The Dominion KX II has very sophisticated video processing algorithms
that optimize bandwidth and performance for a variety of environments.
In addition, they are highly configurable since there are many settings to
optimize bandwidth usage. In particular, the Connection Speed setting
in the remote clients (VKC, MPC) can be set to reduce the bandwidth
used.
312
Appendix D: FAQs
Unlike KX I, the Noise Filter parameter does not generally have a large
role in reducing bandwidth or improving performance.
How much bandwidth does KX II use for common tasks?
Bandwidth primarily depends on the user's task and actions. The more
the server's video screen changes, the more bandwidth is utilized.
The table below summarizes some standard use cases using the
Dominion KX II's default bandwidth settings and with two reduced
bandwidth settings (Connection Speed setting of 1Mbit with 15 and 8 bit
color) on a Windows XP target server (1024x768 resolution) over a 100
Mbit/s LAN:
User task
Default
1Mbit speed
& 8 bit color
0 KB/s
1Mbit speed
& 15 bit
color
0 KB/s
Idle Windows
Desktop
Move mouse cursor
5 - 15 KB/s
2 - 6 KB/s
2 - 3 KB/s
Drag icon
40 - 70 KB/s
10-25 KB/s
5 - 15 KB/s
Drag folder
10 - 40 KB/s
5 - 20 KB/s
5 - 10 KB/s
Open text window
50 - 100 KB/s
25 - 50 KB/s
10 - 15 KB/s
Continuous typing
1 KB/s
.5 - 1 KB/s
.2 - .5 KB/s
Scroll text window
10 - 50 KB/s
5 -25 KB/s
2 - 10 KB/s
Close text window
50 - 100 KB/s
20 - 40 KB/s
10 - 15 KB/s
Open panel
50 - 100 KB/s
60 - 70 KB/s
20 - 30 KB/s
Change tab in panel 40 - 50 KB/s
20 - 50 KB/s
10 - 20 KB/s
Close panel
40 - 60 KB/s
20 - 30 KB/s
Change panel option 2 - 10 KB/s
1 - 5 KB/s
1- 3 KB/s
Open browser page
100 - 300 KB/s
50 - 200 KB/s 40 - 80 KB/s
Scroll browser
75 - 200 KB/s
50 - 200 KB/s 30 - 100 KB/s
Close browser
100 - 150 KB/s
75 - 100 KB/s 30 - 60KB/s
Open Start menu
75 - 100 KB/s
50 -75 KB/s
20 - 30 KB/s
Close Start menu
75 - 100 KB/s
25 - 50 KB/s
10 - 15 KB/s
Starfield screen
saver
25 - 50 KB/s
10 - 15 KB/s
7 - 10 KB/s
3D pipes screen
saver
10 - 100 KB/s
5 - 20 KB/s
2 - 10 KB/s
Windows media
video
500 - 1200
KB/s
300 - 500
KB/s
150 - 300
KB/s
50 - 100 KB/s
0 KB/s
313
Appendix D: FAQs
314
User task
Default
1Mbit speed
& 8 bit color
700 - 2500
KB/s
1Mbit speed
& 15 bit
color
400 - 500
KB/s
QuickTime video #1
QuickTime video #2
1500 - 2500
KB/s
400 - 550
KB/s
200 - 350
KB/s
150 - 350
KB/s
Appendix D: FAQs
With the reduced bandwidth settings, bandwidth is reduced significantly
for virtually all tasks. With the 15 bit color setting, perceived performance
is similar to the default parameters. Further, bandwidth reductions are
possible with additional changes in the settings.
Please note that these bandwidth figures are only examples and may
vary from those seen in your environment due to many factors.
How can I reduce bandwidth?
The Dominion KX II provides a variety of settings in our remote clients to
optimize bandwidth and performance. The default settings will provide
an at-the-rack level of performance in standard LAN/WAN environments
with economical use of bandwidth.
Bandwidth management settings include the Connection Speed and
Color Depth. To reduce bandwidth:
Reduce Connection Speed
Reducing the connection speed can significantly reduce the bandwidth
used. In standard LAN/WAN environments, setting the connection
speed to 1.5 or 1Mbit per second will reduce bandwidth while
maintaining good performance. Settings below this will further reduce
bandwidth and are appropriate for slow bandwidth links.
Reduce Color Depth
Reducing the color depth will also significantly decrease bandwidth and
increase performance, but fewer colors will be used, resulting in video
degradation. This may be acceptable for certain system administration
tasks.
For slow Internet connections, use of 8 bit color or lower bit depths can
reduce bandwidth and improve performance.
Other tips to decrease bandwidth include:

Use a solid desktop background instead of a complex image

Disable screen savers

Use a lower resolution on the target server

Uncheck the “Show window contents while dragging” option in
Windows

Use simple images, themes and desktops (for example. Windows
Classic).
What should I do on slower bandwidth links?
315
Appendix D: FAQs
The connection speed and color depth settings can be tweaked to
optimize performance for slower bandwidth links. For example, in the
Multi-Platform Client or the Virtual KVM Client, set the connection speed
to 1.5Mb or 1Mb and the color depth to 8 bit. Even lower connection
speeds and color depths can be used for very low bandwidth situations.
I want to connect over the Internet. What type of performance
should I expect?
It depends on the bandwidth and latency of the Internet connection
between your remote client and the Dominion KX II. With a cable
modem or high speed DSL connection, your performance can be very
similar to a LAN/WAN connection. For lower speed links, use the
suggestions above to improve performance.
I have a high bandwidth environment. How can I optimize
performance?
The default settings will provide strong performance in a high bandwidth
environment. Ensure that the connection speed is set to 100Mb or 1Gb
and the color depth is set to15 bit RGB Color.
What is the maximum remote (over IP) video resolution supported?
The Dominion KX II is the first and only KVM-over-IP switch to support
full High Definition (HD) remote video resolution – 1920x1080.
In addition, popular widescreen formats are supported, including
1600x1200, 1680x1050 and 1440x900, so remote users can work with
today‟s higher resolution monitors.
What about servers with DVI ports?
Servers with DVI ports that support DVI-A (analog) and DVI-I (integrated
analog and digital) can use a simple, passive adapter such as the
ADVI-VGA to convert the DVI port to a VGA plug that can be connected
to a Dominion KX II CIM‟s VGA plug.
Servers with DVI ports that only support DVI-D (digital) would need a
more expensive adapter, but customers should check to see if the
server‟s video card can be configured to support DVI-I or DVI-A.
316
Appendix D: FAQs
Ethernet and IP Networking
Does the Dominion KX II offer dual gigabit Ethernet ports to provide
redundant fail-over?
Yes. The Dominion KX II features dual gigabit Ethernet ports to provide
redundant failover capabilities. Should the primary Ethernet port (or the
switch/router to which it is connected) fail, the Dominion KX II will failover
to the secondary network port with the same IP address, ensuring that
server operations are not disrupted. Note that automatic failover must be
enabled by the administrator.
What is the speed of the Dominion KX II's Ethernet interfaces?
The Dominion KX II supports gigabit as well as 10/100 Ethernet. The
Dominion KX II supports two 10/100/1000 speed Ethernet interfaces,
with configurable speed and duplex settings (either autodetected or
manually set).
Does the Dominion KX II offer dual gigabit Ethernet ports to provide
redundant failover or load balancing?
Yes. Dominion KX II features dual gigabit Ethernet ports to provide
redundant failover capabilities. Should the primary Ethernet port (or the
switch/router to which it is connected) fail, Dominion KX II will failover to
the secondary network port with the same IP address – ensuring that
server operations are not disrupted. Note that automatic failover must be
enabled by the administrator.
Can I access the Dominion KX II over a wireless connection?
Yes. The Dominion KX II not only uses standard Ethernet, but also very
conservative bandwidth with very high quality video. Thus, if a wireless
client has network connectivity to the Dominion KX II, servers can be
configured and managed at BIOS-level wirelessly.
Can the Dominion KX II be used over the WAN (Internet), or just
over the corporate LAN?
Whether via a fast corporate LAN, the less predictable WAN (Internet),
cable modem or dial-up modem, the Dominion KX II's KVM-over-IP
technology can accommodate the connection.
Can I use the Dominion KX II with a VPN?
Yes, the Dominion KX II uses standard Internet Protocol (IP)
technologies from Layer 1 through Layer 4. Traffic can be easily tunneled
through standard VPNs.
Can I use Dominion KX II with a proxy server?
Yes. The Dominion KX II can be used with a SOCKS proxy server,
assuming the remote client PC is configured appropriately. Contact the
user documentation or online help for more information.
317
Appendix D: FAQs
How many TCP ports must be open on my firewall in order to
enable network access to the Dominion KX II? Are these ports
configurable?
Only one. The Dominion KX II protects network security by only requiring
access to a single TCP port to operate. This port is completely
configurable for additional security.
Note that, of course, to use the Dominion KX II's optional web browser
capability, the standard HTTPS port 443 must also be open.
Does the Dominion KX II require an external authentication server
to operate?
No. The Dominion KX II is a completely self-sufficient. After assigning an
IP address to the Dominion KX II, it is ready to use. Its web browser and
authentication capabilities are completely built-in.
If an external authentication server (such as LDAP, Active Directory,
RADIUS, etc.) is used, the Dominion KX II allows this as well, and will
even failover to its own internal authentication should the external
authentication server become unavailable. In this way, the Dominion KX
II's design philosophy is optimized to provide ease of installation,
complete independence from any external server, and maximum
flexibility.
Can the Dominion KX II be used with CITRIX?
The Dominion KX II may work with remote access products like CITRIX if
configured appropriately, but Raritan cannot guarantee it will work with
acceptable performance. Products like CITRIX utilize video redirection
technologies similar in concept to digital KVM switches so that two
KVM-over-IP technologies are being used simultaneously.
Can the Dominion KX II use DHCP?
DHCP addressing can be used, however, Raritan recommends fixed
addressing since the Dominion KX II is an infrastructure device and can
be accessed and administered more effectively with a fixed IP address.
I'm having problems connecting to the Dominion KX II over my IP
network. What could be the problem?
The Dominion KX II relies on your LAN/WAN network. Some possible
problems include:
318

Ethernet autonegotiation - On some networks, 10/100
autonegotiation does not work properly and the Dominion KX II unit
must be set to 100MB/full duplex or the appropriate choice for its
network.

Duplicate IP address - If the IP address of the Dominion KX II is the
same as another device, network connectivity may be inconsistent.
Appendix D: FAQs

Port 5000 conflicts - If another device is using port 5000, the
Dominion KX II default port must be changed (or the other device
must be changed).
When changing the IP address of the Dominion KX II or swapping in a
new Dominion KX II, sufficient time must be allowed for its IP and MAC
addresses to be known throughout the Layer 2 and Layer 3 networks.
319
Appendix D: FAQs
IPv6 Networking
What is IPv6?
IPv6 is the acronym for “Internet Protocol Version 6”. IPv6 is the “next
generation” IP protocol which will replace the current IP Version 4 (IPv4)
protocol.
IPv6 addresses a number of problems in IPv4, such as the limited
number of IPv4 addresses. It also improves IPv4 in areas such as
routing and network auto-configuration. IPv6 is expected to gradually
replace IPv4, with the two coexisting for a number of years.
IPv6 helps one of the largest headaches of an IP network from the
administrator‟s point of view; configuring and maintaining an IP network.
Why does the Dominion KX II support IPv6 networking?
US government agencies and the Department of Defense are now
mandated to purchase IPv6 compatible products. In addition, many
enterprises and foreign countries such as China will be transitioning to
IPv6 over the next several years.
What is "dual stack" and why is it required?
Dual stack is the ability to simultaneously support both IPv4 and IPv6
protocols. Given the gradual transition from IPv4 to IPv6, dual stack is a
fundamental requirement for IPv6 support.
How do I enable IPv6 on the Dominion KX II?
Use the Network Settings page, available from the Device Settings menu
in Dominion KX II. Enable IPv6 addressing and choose manual or
auto-configuration. You must also enable it in MPC.
What if I have an external server with an IPv6 address that I want to
use with my Dominion KX II?
The Dominion KX II can access external servers via their IPv6
addresses, for example, an SNMP Manager, Syslog server, or LDAP
server.
Using the Dominion KX II‟s dual-stack architecture, these external
servers can be accessed via (1) an IPv4 address, (2) IPv6 address or (3)
hostname. So the Dominion KX II supports the mixed IPv4/IPv6
environment many customers will have.
Does the Dominion KX I support IPv6?
No, the Dominion KX I does not support IPv6 addresses.
What if my network doesn't support IPv6?
320
Appendix D: FAQs
The Dominion KX II‟s default networking is set at the factory for IPv4
only. When you are ready to use IPv6, then follow the above instructions
to enable IPv6/IPv4 dual stack operation.
Where can I get more information on IPv6?
See www.ipv6.org for general information on IPv6. The Dominion KX II
User Guide describes the Dominion KX II‟s support for IPv6.
321
Appendix D: FAQs
Servers
Does the Dominion KX II depend on a Windows server to operate?
Absolutely not. Because users depend on the KVM infrastructure to
always be available in any scenario whatsoever (as they will likely need
to use the KVM infrastructure to fix problems), the Dominion KX II is
designed to be completely independent from any external server. For
example, should the data center come under attack from a malicious
Windows worm or virus, administrators will need to use the KVM solution
to resolve the situation. Therefore, it is imperative that the KVM solution,
in turn, must not rely on these same Windows servers (or any server, for
that matter) to be operational in order for the KVM solution to function.
To this end, the Dominion KX II is completely independent. Even if a user
chooses to configure the Dominion KX II to authenticate against an
Active Directory server - if that Active Directory server becomes
unavailable, the Dominion KX II's own authentication will be activated
and fully functional.
Do I need to install a web server such as Microsoft® Internet
Information Services (IIS) in order to use the Dominion KX II's web
browser capability?
No. The Dominion KX II is a completely self-sufficient device. After
assigning an IP address to the Dominion KX II, it's ready to use since it
comes with web browser and authentication capabilities completely
built-in.
What software do I have to install in order to access the Dominion
KX II from a particular workstation?
None. The Dominion KX II can be accessed completely via a web
browser. However, there is an optional installed client provided on
Raritan's website (www.raritan.com), which is required for modem
connections. A Java-based client is now available for non-Windows
users.
What should I do to prepare a server for connection to the
Dominion KX II?
Simply set the mouse parameters in order to provide users with the best
mouse synchronization during remote connections, as well as turning off
the power management features that effect screen display. However, if
the new D2CIM-VUSB adapter is used (supporting Absolute Mouse
Synchronization™), then manually setting the mouse parameters isn't
necessary.
What about mouse synchronization?
322
Appendix D: FAQs
For many KVM-over-IP users, mouse synchronization is a frustrating
experience. The Dominion KX II‟s Absolute Mouse Synchronization
provides for a tightly synchronized mouse without requiring server mouse
setting changes on Windows and Apple® Mac® servers. For other
servers, the Intelligent Mouse mode or the speedy, single mouse mode
can be used to avoid changing the server mouse settings.
Blade Servers
Can I connect blade servers to the Dominion KX II?
Yes you can. The Dominion KX II supports popular blade server models
from the leading blade server manufacturers: HP®, IBM® and Dell®.
Which blade servers are supported?
The following models are supported:

Dell® PowerEdge® 1855, 1955 and M1000e

HP BladeSystem c3000 and c7000

IBM® BladeCenter® H and E
Note: IBM BladeCenter Model S, T, and HT are handled using the
IBM (Other) selection.
323
Appendix D: FAQs
Are the Paragon Blade CIMs used?
No, the Paragon II Blade CIM will not work with the Dominion KX II.
Which CIM should I use?
It depends on the type of KVM ports on the specific make and model of
the blade server you are using. The following CIMs are supported:
DCIM-PS2, DCIM-USBG2, D2CIM-VUSB and D2CIM-DVUSB.
What types of access and control are available?
The Dominion KX II provides automated & secure KVM access: (1)
at-the-rack, (2) remotely over IP, (3) via CommandCenter and (4) by
modem.
Do I have to use hotkeys to switch between blades?
Some blade servers require you to use hotkeys to switch between
blades. With the Dominion KX II, you don't have to use these hotkeys.
Just click on the name of the blade server and the Dominion KX II will
automatically switch to that blade without the explicit use of the hotkey.
Can I access the blade server's management module?
Yes, you can define the URL of the management module and access it
from the Dominion KX II or from CC-SG. If configured, one-click access
is available.
How many blade servers can I connect to a Dominion KX II ?
For performance and reliability reasons, you can connect up to 8 blade
chassis to a Dominion KX II, regardless of model. Raritan recommends
connecting up to two times the number of remote connections supported
by the device. For example, with a KX2-216 with two remote channels,
we recommend connecting up to 4 blade server chassis. You can of
course connect individual servers to the remaining server ports.
I'm an SMB customer with a few Dominion KX II's. Must I use your
CC-SG management station?
No, you don't have to. SMB customers are not required to use CC-SG to
use the new blade features.
I'm an enterprise customer using CC-SG. Can I access blade
servers via CC-SG?
Yes. Once blade servers are configured on the Dominion KX II, the
CC-SG user can access them via KVM connections. In addition the
blade servers are organized by chassis as well as CC-SG custom views.
What if I want in-band or embedded KVM access?
Yes, in-band and embedded access to blade servers can be configured
within CC-SG.
324
Appendix D: FAQs
I'm running VMWare on some of my blade servers. Is this
supported?
Yes, with CC-SG you can display and access virtual machines running
on blade servers.
Is virtual media supported?
We support VM on IBM BladeCenter® Model H and E with the D2CIM DVUSB.
Is Absolute Mouse Synchronization supported?
Servers with internal KVM switches inside the blade chassis typically do
not support absolute mouse technology. For HP Blade and some Dell
blade servers, the CIM is connected to each blade, so absolute mouse is
supported if the underlying OS running on the blade does.
Is blade access secure?
Yes, blade access uses all of the standard Dominion KX II security
features such as 128 bit or 256 bit encryption. In addition, there are
blade-specific security features such as per blade access permissions
and hotkey-blocking that eliminates un-authorized access.
Does the Dominion KSX II or the KX II-101 support blade servers?
At this time, these products do not have these new blade server features.
325
Appendix D: FAQs
Installation
Besides the device itself, what do I need to order from Raritan to
install the Dominion KX II?
Each server that connects to the Dominion KX II requires a Dominion or
Paragon Computer Interface Module (CIM), an adapter that connects
directly to the keyboard, video, and mouse ports of the server.
What kind of Cat5 cabling should be used in my installation?
The Dominion KX II can use any standard UTP (unshielded twisted pair)
cabling, whether Cat5, Cat5e, or Cat6. Often in our manuals and
marketing literature, Raritan will simply say “Cat5” cabling for short. In
actuality, any brand UTP cable will suffice for the Dominion KX II.
What types of servers can be connected to the Dominion KX II?
The Dominion KX II is completely vendor independent. Any server with
standard-compliant keyboard, video, and mouse ports can be connected.
How do I connect servers to the Dominion KX II?
Servers that connect to the Dominion KX II require a Dominion or
Paragon CIM, which connects directly to the keyboard, video, and mouse
ports of the server. Then, connect each CIM to the Dominion KX II using
standard UTP (twisted pair) cable such as Cat5, Cat5e, or Cat6.
How far can my servers be from the Dominion KX II?
In general servers can be up to 150 feet (45 m) away from the Dominion
KX II depending on the type of server. Refer to the Raritan website
(www.raritan.com) or Target Server Connection Distance and Video
Resolution (on page 273) for more information. For the new
D2CIM-VUSB and D2CIM-DVUSB CIMs that support virtual media and
Absolute Mouse Synchronization, a 100 (30 m) foot range is
recommended.
Some operating systems lock up when I disconnect a keyboard or
mouse during operation. What prevents servers connected to the
Dominion KX II from locking up when I switch away from them?
Each Dominion computer interface module (DCIM) dongle acts as a
virtual keyboard and mouse to the server to which it is connected. This
technology is called KME (keyboard/mouse emulation). Raritan's KME
technology is data center grade, battle-tested, and far more reliable than
that found in lower-end KVM switches: it incorporates more than 15
years of experience and has been deployed to millions of servers
worldwide.
Are there any agents that must be installed on servers connected to
the Dominion KX II?
326
Appendix D: FAQs
Servers connected to the Dominion KX II do not require any software
agents to be installed, because the Dominion KX II connects directly via
hardware to servers' keyboard, video, and mouse ports.
How many servers can be connected to each the Dominion KX II
device?
The Dominion KX II models range from 8, 16, or 32 server ports in a 1U
chassis to 64 server ports in a 2U chassis. This is the industry's highest
digital KVM switch port density.
What happens if I disconnect a server from the Dominion KX II and
reconnect it to another Dominion KX II device, or connect it to a
different port on the same Dominion KX II device?
Dominion KX II will automatically update the server port names when
servers are moved from port to port. Furthermore, this automatic update
does not just affect the local access port, but propagates to all remote
clients and the optional CommandCenter Secure Gateway management
appliance.
How do I connect a serially controlled (RS-232) device to the
Dominion KX II, such as a Cisco router/switch or a headless Sun™
server?
If there are only a few serially-controlled devices, they may be connected
to a Dominion KX II using Raritan's new P2CIM-SER serial converter.
However, if there are four or more serially-controlled devices, we
recommend the use of Raritan's KSX II line or SX line of secure console
servers. These devices are easy to use, configure and manage, and can
be completely integrated with a Dominion Series deployment. In
particular, many UNIX and networking administrators appreciate the
ability to directly SSH to a device.
327
Appendix D: FAQs
Local Port
How do I physically connect multiple Dominion KX II devices together
into one solution?
Can I access my servers directly from the rack?
Yes. At the rack, the Dominion KX II functions just like a traditional KVM
switch, allowing control of up to 64 servers using a single keyboard,
monitor, and mouse.
Can I consolidate the local ports of multiple Dominion KX II’s?
Yes. You can connect the local ports of multiple Dominion KX II switches
to another Dominion KX II using the "tiering" feature of the Dominion KX
II. You can then access the servers connected to your Dominion KX II
devices from a single point in the data center via a consolidated port list.
When I am using the local port, do I prevent other users from
accessing servers remotely?
No. The Dominion KX II local port has a completely independent access
path to the servers. This means a user can access servers locally at the
rack without compromising the number of users that access the rack
remotely at the same time.
Can I use a USB keyboard or mouse at the local port?
Yes. The Dominion KX II offers both PS/2 and USB keyboard and mouse
ports on the local port. Note that the USB ports are USB v1.1, and
support keyboards and mice only, not USB devices such as scanners or
printers.
Is there an onscreen display for local, at-the-rack access?
Yes, but the Dominion KX II's at-the-rack access goes way beyond
conventional OSDs. Featuring the industry's first browser-based interface
for at-the-rack access, the Dominion KX II's local port uses the same
interface for local and remote access. Moreover, most administrative
functions are available at-the-rack.
How do I select between servers while using the local port?
The local port displays the connected servers using the same user
interface as the remote client. Connect to a server with a simple click of
the mouse.
How do I ensure that only authorized users can access servers
from the local port?
Users attempting to use the local port must pass the same level of
authentication as those accessing remotely. This means that:
328
Appendix D: FAQs

If the Dominion KX II is configured to interact with an external
RADIUS, LDAP, or Active Directory server, users attempting to
access the local port will authenticate against the same server.

If the external authentication servers are unavailable, the Dominion
KX II fails-over to its own internal authentication database.

The Dominion KX II has its own standalone authentication, enabling
instant, out-of-the-box installation.
If I use the local port to change the name of a connected server,
does this change propagate to remote access clients as well? Does
it propagate to the optional CommandCenter unit?
Yes. The local port presentation is identical and completely in sync with
remote access clients, as well as Raritan's optional CommandCenter
Secure Gateway management device. To be clear, if the name of a
server via the Dominion KX II onscreen display is changed, this updates
all remote clients and external management servers in real-time.
If I use the Dominion KX II's remote administration tools to change
the name of a connected server, does that change propagate to the
local port OSD as well?
Yes. If the name of a server is changed remotely, or via Raritan's
optional CommandCenter Secure Gateway management unit, this
update immediately affects the Dominion KX II's onscreen display.
Sometimes I see "shadows" on the local port user interface. Why
does that occur?
This shadow/ghosting effect may occur with LCD monitors that have
been on for long periods. The LCD properties and the electrical/static
charge can produce these effects when the screen is on for a long time.
329
Appendix D: FAQs
Extended Local Port (Dominion KX2-832 and KX2-864 Models Only)
What is the extended local port?
The Dominion KX2-832 and KX2-864 feature an extended local port.
The Dominion KX II eight user models have a standard local port, plus a
new extended local port that extends the local port, via Cat5 cable,
beyond the rack to a control room, another point in the data center or to
a Paragon II switch.
Can I connect the extended local port to another Dominion KX II?
Yes, you can connect the extended local port to a server port of another
Dominion KX II using the "tiering" feature of the Dominion KX II.
Is a user station required for the extended local port?
Yes, the following devices can function as the “user station” for the
extended local port: Paragon II EUST, Paragon II UST, and the Cat5
Reach URKVMG device. In addition, the extended local port can be
connected via Cat5 cable to a server port on a Paragon II switch. This
configuration can be used to consolidate the local ports of many
KX2-8xxx devices to a single switch.
How far can the user station be from the Dominion KX II?
The distance is 200' to 1000', but varies according to the type of user
station, the video resolution, cable type and quality.
Is a CIM required?
No CIM is required. Just connect a Cat5 cable.
Must I use the extended local port?
No, the extended local port is an optional feature and is disabled by
default. Use the Local Port Settings page to enable it. You can also
disable the standard local port if you are not going to use it for added
security.
330
Appendix D: FAQs
Power Control
Does the Dominion KX II have a dual power option?
All of the Dominion KX II models come equipped with dual AC inputs and
power supplies with automatic fail-over. Should one of the power inputs
or power supplies fail, then the Dominion KX II will automatically switch
to the other.
Does the power supply used by the Dominion KX II automatically
detect voltage settings?
Yes. The Dominion KX II's power supply can be used in AC voltage
ranges from 100-240 volts, at 50-60 Hz.
If a power supply or input fails, will I be notified?
The Dominion KX II front panel LED will notify the user of a power failure.
An entry will also be sent to the Audit Log and displayed on the Dominion
KX II Remote Client User Interface. If configured by the administrator,
then SNMP or Syslog events will be generated.
What type of power control capabilities does the Dominion KX II
offer?
Raritan's Remote Power Control power strips can be connected to the
Dominion KX II to provide power control of the KVM target servers. After
a simple one-time configuration step, just right click the server name to
power on, off, or recycle a hung server. Note that a hard reboot provides
the physical equivalent of unplugging the server from the AC power line,
and reinserting the plug.
How many PDUs can be connected to a Dominion KX II?
Up to eight PDUs can be connected to a Dominion KX II device.
How do I connect the PDU to the Dominion KX II?
The D2CIM-PWR is used to connect the power strip to the Dominion KX
II. The D2CIM-PWR must be purchased separately; it does not come
with the PDU.
Does the Dominion KX II support servers with multiple power
supplies? What if each power supply is connected to a different
power strip?
Yes. The Dominion KX II can be easily configured to support multiple
power supplies connected to multiple power strips. Up to eight (8) power
strips can be connected to the Dominion KX II device. Four power
supplies can be connected per target server to multiple power strips.
Does the Dominion KX II display statistics and measurements from
the PDU?
331
Appendix D: FAQs
Yes. PDU-level power statistics, including power, current and voltage,
are retrieved from the PDU and displayed to the user.
Does remote power control require any special server
configuration?
Some servers ship with default BIOS settings such that the server does
not automatically restart after losing and regaining power. For these
servers, see the server‟s documentation to change this setting.
What happens when I recycle power to a server?
This is the physical equivalent of unplugging the server from the AC
power line, and reinserting the plug.
Can I power on/off other equipment (non-servers) connected to a
PDU?
Yes. You can power on/off other equipment attached to the PDU by
outlet from the Dominion KX II‟s browser­based interface.
What type of power strips does the Dominion KX II support?
To take advantage of the Dominion KX II's integrated power control user
interface, and more importantly, integrated security, use Raritan's
Remote Power Control (RPC) power strips. RPCs come in many outlet,
connector, and amp variations. The D2CIM-PWR must be purchased to
connect the RPC to the Dominion KX II.
332
Appendix D: FAQs
Scalability
How do I physically connect multiple Dominion KX II devices
together into one solution?
To physically connect multiple Dominion KX II devices together for
consolidated local access, you can connect the local ports of multiple
“tiered” (or “cascaded”) Dominion KX II switches to a “base” Dominion
KX II using the “tiering” feature of the Dominion KX II. You can then
access the servers connected to your Dominion KX II devices from a
single point in the data center via a consolidated port list.
The D2CIM-DVUSB CIM must be used to connect the “tiered” Dominion
KX II switch to the “base” switch. Or for the KX2-832 and KX2-864, the
extended local port can be connected via CAT5/6 cable (no CIM
required) to the base Dominion KX II switch.
Access via the consolidated port list is available in the data center or
even from a remote PC. All servers connected to the tiered Dominion KX
II‟s can be accessed via a hierarchical port list or via search (with
wildcards).
Two levels of tiering are supported; up to 1024 devices can be accessed
in a tiered configuration. Remote power control is also supported.
Virtual media, smart card and blade server access via tiered access will
be supported in a future release. Of course these features are available
when accessed via a standard remote connection.
While remote IP server access via the consolidated port list is available
as a convenience, accessing the tiered server from CommandCenter or
directly via the Dominion KX II the server is connected to is
recommended for optimal performance.
Do I have to physically connect Dominion KX II devices together?
Multiple Dominion KX II units do not need to be physically connected
together. Instead, each Dominion KX II unit connects to the network, and
they automatically work together as a single solution if deployed with
Raritan‟s CommandCenter Secure Gateway (CC-SG) management
appliance.
CC-SG acts as a single access point for remote access and
management. CC-SG offers a significant set of convenient tools, such as
consolidated configuration, consolidated firmware update and a single
authentication and authorization database.
Customers using CC-SG for centralized remote access can make good
use of the Dominion KX II‟s tiering (cascading) feature to consolidate the
local ports of multiple Dominion KX II switches and locally access up to
1024 servers from a single console when in the data center.
Is CC-SG required?
333
Appendix D: FAQs
For customers wanting stand-alone usage (without a central
management system), multiple Dominion KX II units still interoperate and
scale together via the IP network. Multiple Dominion KX II switches can
be accessed from the Dominion KX II web-based user interface and from
the Multiplatform Client (MPC).
Can I connect an existing analog KVM switch to the Dominion KX
II?
Yes. Analog KVM switches can be connected to one of the Dominion KX
II's server ports. Simply use a D2CIM-DVUSB or D2CIM-VUSB and
attach it to the user ports of the existing analog KVM switch. Please Note
that analog KVM switches vary in their specifications and Raritan cannot
guarantee the interoperability of any particular third-party analog KVM
switch. Contact Raritan technical support for further information.
334
Appendix D: FAQs
Computer Interface Modules (CIMs)
Can I use Computer Interface Modules (CIMs) from Raritan's analog
matrix KVM switch, Paragon, with the Dominion KX II?
Yes. Certain Paragon computer interface modules (CIMs) may work with
the Dominion KX II (check the Raritan Dominion KX II release notes on
the website for the latest list of certified CIMs).
However, because Paragon CIMs cost more than Dominion KX II CIMs
(as they incorporate technology for video transmission of up to 1000 feet
[300 meters]), it is not generally advisable to purchase Paragon CIMs for
use with the Dominion KX II. Also note that when connected to the
Dominion KX II, Paragon CIMs transmit video at a distance of up to 150
feet, the same as the Dominion KX II CIMs; not at 1000 feet [300
meters], as they do when connected to Paragon.
Can I use the Dominion KX II Computer Interface Modules (CIMs)
with Raritan's analog matrix KVM switch, Paragon?
No. The Dominion KX II computer interface modules (CIMs) transmit
video at ranges of 50 to 150 feet (15 - 45 m) and thus do not work with
Paragon, which requires CIMs that transmit video at a range of 1000 feet
(300 meters). To ensure that all Raritan's customers experience the very
best quality video available in the industry - a consistent Raritan
characteristic - Dominion Series CIMs do not interoperate with Paragon.
Does the Dominion KX II support Paragon Dual CIMs?
Yes. The Dominion KX II now supports Paragon II Dual CIMs
(P2CIM-APS2DUAL and P2CIM-AUSBDUAL), which can connect
servers in the data center to two different Dominion KX II switches.
If one Dominion KX II switch is not available, the server can be accessed
through the second Dominion KX II switch, providing redundant access
and doubling the level of remote KVM access.
Please note these are Paragon CIMs, so they do not support the
Dominion KX II advanced features such as virtual media, absolute
mouse, and so on.
335
Appendix D: FAQs
Security
Is the Dominion KX II FIPS 140-2 Certified?
The Dominion KX II, as of Release 2.2.0, provides users with the option
to use an embedded FIPS 140-2-validated cryptographic module running
on a Linux platform per FIPS 140-2 implementation guidelines. This
cryptographic module is used for encryption of KVM session traffic
consisting of video, keyboard, mouse, virtual media and smart card data.
What kind of encryption does the Dominion KX II use?
The Dominion KX II uses industry-standard (and extremely secure) RC4
or AES encryption, both in its SSL communications as well as its own
data stream. Literally no data is transmitted between remote clients and
the Dominion KX II that is not completely secured by encryption.
Does the Dominion KX II support AES encryption as recommended
by the US Government's NIST and FIPS 140-2 standards?
The Dominion KX II utilizes the Advanced Encryption Standard (AES)
encryption for added security.
AES is a US government approved cryptographic algorithm that is
recommended by the National Institute of Standards and Technology
(NIST) in the FIPS Standard 197.
Does the Dominion KX II allow encryption of video data? Or does it
only encrypt keyboard and mouse data?
Unlike competing solutions, which only encrypt keyboard and mouse
data, the Dominion KX II does not compromise security; it allows
encryption of keyboard, mouse and video data.
How does the Dominion KX II integrate with external authentication
servers such as Active Directory®, RADIUS, or LDAP?
Through a very simple configuration, the Dominion KX II can be set to
forward all authentication requests to an external server such as LDAP,
Active Directory, or RADIUS. For each authenticated user, the Dominion
KX II receives the user group to which that user belongs from the
authentication server. The Dominion KX II then determines the user's
access permissions depending on the user group to which he or she
belongs.
How are usernames and passwords stored?
Should the Dominion KX II's internal authentication capabilities be used,
all sensitive information such as usernames and passwords are stored in
an encrypted format. Literally no one, including Raritan Technical
Support or Product Engineering departments, can retrieve those
usernames and passwords.
Does the Dominion KX II support strong password?
336
Appendix D: FAQs
Yes, the Dominion KX II has administrator-configurable, strong password
checking to ensure that user-created passwords meet corporate and/or
government standards and are resistant to brute force hacking.
If the Dominion KX II encryption mode is set to Auto, what level of
encryption is achieved?
The encryption level that is autonegotiated is dependent on the browser
in use.
Can I upload my own digital certificate to the Dominion KX II?
Yes. Customers can upload self-signed or certificate authority-provided
digital certificates to the Dominion KX II for enhanced authentication and
secure communication.
Does the Dominion KX II support a configurable security banner?
Yes. For government, military and other security conscious customers
requiring a security message before user login, the Dominion KX II can
display a user-configurable banner message and optionally require
acceptance.
My security policy does not allow the use of standard TCP port
numbers. Can I change them?
Yes. For customers wishing to avoid the standard TCP/IP port numbers
to increase security, the Dominion KX II allows the administrator to
configure alternate port numbers.
337
Appendix D: FAQs
Smart Cards and CAC Authentication
Does the Dominion KX II support smart card and CAC
authentication?
Yes, smart cards and DoD Common Access Card (CAC) authentication
to target servers is supported in release 2.1.10 and later.
What Dominion KX II models support smart cards/CAC?
All Dominion KX II models are supported. The Dominion KSX2 and
KX2-101 do not currently support smart cards and CAC.
Do enterprise and SMB customers use smart cards, too?
Yes. However, the most aggressive deployment of smart cards is in the
U.S. federal government.
What CIMs support smart cards/CAC?
The D2CIM-DVUSB is required. This CIM must be upgraded with the
release 2.1.10 and later of the firmware.
What firmware version is required?
The Dominion KX II release 2.1.10 and later is required.
What smart card readers are supported?
The required reader standards are USB CCID and PC/SC. Consult the
Dominion KX II 2.1.10 Supported and Unsupported Smart Card
Readers (on page 276) or the Release Notes for a list of certified
readers and more information.
Can smart card/CAC authentication work on the local port and via
Command Center?
Yes. For the local port, connect a compatible smart card reader to the
USB port of the Dominion KX II.
Are the Paragon smart card enabled UST and CIM used?
No, the P2-EUST/C and P2CIM-AUSB-C are not part of the Dominion
KX II solution.
338
Appendix D: FAQs
Manageability
Can the Dominion KX II be remotely managed and configured via
web browser?
Yes, the Dominion KX II can be completely configured remotely via web
browser. Note that this does require that the workstation have an
appropriate Java Runtime Environment (JRE) version installed.
Besides the initial setting of the Dominion KX II's IP address, everything
about the solution can be completely set up over the network. (In fact,
using a crossover Ethernet cable and the Dominion KX II's default IP
address, you can even configure the initial settings via web browser.)
Can I backup and restore the Dominion KX II's configuration?
Yes, the Dominion KX II's device and user configurations can be
completely backed up for later restoration in the event of a catastrophe.
The Dominion KX II's backup and restore functionality can be used
remotely over the network or via the Remote Console.
What auditing or logging does the Dominion KX II offer?
For complete accountability, the Dominion KX II logs all major user and
system events with a date and time stamp. For instance, reported events
include (but are not limited to): user login, user log off, user access of a
particular server, unsuccessful login, configuration changes, and so forth.
Can the Dominion KX II integrate with Syslog?
Yes. In addition to the Dominion KX II's own internal logging capabilities,
the Dominion KX II can send all logged events to a centralized Syslog
server.
Can the Dominion KX II integrate with SNMP?
Yes. In addition to the Dominion KX II's own internal logging capabilities,
the Dominion KX II can send SNMP traps to SNMP management
systems like HP Openview and Raritan's CC-NOC.
Can the Dominion KX II's internal clock be synchronized with a
timeserver?
Yes, the Dominion KX II supports the industry-standard NTP protocol for
synchronization with either a corporate timeserver or with any public
timeserver (assuming that outbound NTP requests are allowed through
the corporate firewall).
339
Appendix D: FAQs
Miscellaneous
What is the Dominion KX II's default IP address?
192.168.0.192
What is the Dominion KX II's default user name and password?
The Dominion KX II's default user name is admin and the default
password is raritan [all lower case]. However, for the highest level of
security, the Dominion KX II forces the administrator to change the
Dominion KX II default administrative user name and password when the
unit is first booted up.
I changed and subsequently forgot the Dominion KX II's
administrative password; can you retrieve it for me?
The Dominion KX II contains a hardware reset button that can be used to
factory reset the device, which will reset the administrative password on
the device.
I am logged into the Dominion KX II using Firefox®, and I opened
another Firefox browser. I am automatically logged into the same
Dominion KX II with the second Firefox browser. Is this right?
Yes, this is correct behavior and is the direct result of how browsers and
cookies function.
I am logged into the Dominion KX II using Firefox and I attempt to
log into another Dominion KX II using another Firefox browser
session from the same client. I am logged off of both Dominion KX
IIs;. Is this correct behavior?
Yes, to access two different Dominion KX II devices either close the first
session or use another client PC.
When I'm running a KVM session using Firefox as my browser and
certain dialogs are opened in the Virtual KVM Client (for example,
Connection Properties, Video Settings), it seems to block the
Firefox browser (even other Firefox sessions). What can I do?
This is normal behavior since all Firefox sessions are associated. Once
you close the Virtual KVM Client dialog, Firefox will no longer be blocked.
340
Index
A
A. AC Power • 26
Absolute Mouse Mode • 72
Access Telnet from a Windows PC • 232
Accessing a Target Server • 249
Accessing the Dominion KX II Using CLI • 231
Accessing Virtual Media on a Windows 2000
Server Using a D2CIM-VUSB • 302
Active KVM Client (AKC) • 80
Adding a New User • 118
Adding a New User Group • 109, 118
Adding Attributes to the Class • 285
Adding, Deleting and Editing Favorites • 48
Adjusting Video Settings • 63
Administering the Dominion KX II Console
Server Configuration Commands • 237
AKC Supported Operating Systems and
Browsers • 81
Apple Macintosh Settings • 25
Assigning an IP Address • 30
Associating Outlets with Target Servers on KX
II • 163
Audit Log • 209
Authentication Settings • 120
Auto-Sense Video Settings • 63
Available Resolutions • 244
Available USB Profiles • 101, 299, 310
B
B. Modem Port (Optional) • 27
Backup and Restore • 177, 211
Bandwidth and KVM-over-IP Performance •
312
Blade Chassis Sample URL Formats • 170,
171, 173, 175, 184
Blade Servers • 323
Building a Keyboard Macro • 60
C
C. Network Port • 27
Cabling Example in Tiered Configurations •
142
Calibrating Color • 63
CC-SG • 302
CD-ROM/DVD-ROM/ISO Images • 94, 97
Certified Modems • 146, 272
Changing a Password • 131
Changing a USB Profile when Using a Smart
Card Reader • 300
Changing the Default Password • 29, 38
Changing the Keyboard Layout Code (Sun
Targets) • 35
Changing the Maximum Refresh Rate • 68
Checking Your Browser for AES Encryption •
198, 200
Choosing USB Profiles • 56
CIM Compatibility • 101
CIMs • 300
CLI Commands • 230, 236
CLI Prompts • 236
CLI Syntax -Tips and Shortcuts • 234
Client Applications that Can Be Used with the
Dominion KX II • 5
Command Line Interface (CLI) • 230
Common Commands for All Command Line
Interface Levels • 235
Completion of Commands • 234
Computer Interface Modules (CIMs) • 101,
259, 335
Conditions when Read/Write is Not Available •
96, 97
Configuring and Enabling Tiering • 2, 9, 42,
112, 113, 114, 117, 139, 189, 245
Configuring Blade Chassis • 165
Configuring Date/Time Settings • 146
Configuring Dominion KX II Local Console
Local Port Settings • 250
Configuring Dominion KX II Local Port
Settings • 28, 188, 192, 253
Configuring Dominion KX II Local Port
Settings from the Local Console • 253
Configuring Event Management - Settings •
148
Configuring IP Access Control • 202
Configuring KVM Switches • 139, 158
Configuring Modem Settings • 27, 145
Configuring Network • 238
Configuring Ports • 156
Configuring Power Strip (Rack PDU) Targets •
159
Configuring Standard Target Servers • 157
Configuring USB Profiles (Port Page) • 107,
174, 185
Connect Key Examples • 190, 247, 251
Connecting a Power Strip • 160
Connecting to a KVM Target Server • 52, 56
341
Index
Connecting to Virtual Media • 96
Connection Information • 59
Connection Properties • 57
Create User Groups and Users • 35
Creating a New Attribute • 284
D
D. Local Access Port (Local PC) • 28
Default Login Information • 13
Dell Blade Chassis Configuration • 168
Dell Chassis Cable Lengths and Video
Resolutions • 168, 296
Desktop Background • 14
Device Diagnostics • 228
Device Information • 210
Device Management • 132
Device Services • 137, 169, 172
Devices Supported by the KX2-832 and
KX2-864 Extended Local Port • 273
Diagnostics • 223
Disconnecting KVM Target Servers • 55
Disconnecting Virtual Media • 93, 99
Discovering Devices on the Dominion KX II
Subnet • 48
Discovering Devices on the Local Subnet • 47
Dominion KX II Console Layout • 39
Dominion KX II Console Navigation • 41
Dominion KX II Help • 1
Dominion KX II Local Console • 240
Dominion KX II Local Console Factory Reset •
254
Dominion KX II Local Console Interface • 37,
241
Dominion KX II Overview • 3
Dominion KX II Remote Console Interface • 37
Dominion KX II to Dominion KX II Guidelines •
268
Dominion KX II to Paragon II Guidelines • 269
E
E. Target Server Ports • 29
Editing rciusergroup Attributes for User
Members • 287
Enabling Direct Port Access • 80, 143
Enabling FIPS 140-2 • 199, 200
Enabling SSH • 138
Enabling Telnet • 232
Enabling the AKC Download Server Certificate
Validation • 80, 144
Enabling Tiering • 140
342
Encryption & Share • 197, 200, 268
Entering the Discovery Port • 138
Environmental Requirements • 258
Ethernet and IP Networking • 317
Event Management • 148
Event Management - Destinations • 150
Extended Local Port (Dominion KX2-832 and
KX2-864 Models Only) • 330
F
FAQs • 304
Favorites List Page • 46, 47, 48
Fedora • 297
File Server Setup (File Server ISO Images
Only) • 94
FIPS 140-2 Support Requirements • 201
French Keyboard • 293
From LDAP • 283
From Microsoft Active Directory • 283
G
General Questions • 305
Generic Blade Chassis Configuration • 166
Getting Started • 14, 235
Group-Based IP ACL (Access Control List) •
110, 114, 116, 202
H
Handling Conflicts in Profile Names • 215
Hardware • 9
Help for Choosing USB Profiles • 298
Help Options • 80
Hot Keys and Connect Keys • 247
HP Blade Chassis Configuration (Port Group
Management) • 177, 179
HTTP and HTTPS Port Settings • 2, 138, 280
I
IBM AIX 5.3 Settings • 24
IBM Blade Chassis Configuration • 172
Implementing LDAP/LDAPS Remote
Authentication • 121
Implementing RADIUS Remote Authentication
• 126
Informational Notes • 275, 291
Initial Configuration Using CLI • 235
Installation • 326
Installation and Configuration • 13
Intelligent Mouse Mode • 14, 71
Interface and Navigation • 39
Index
Interface Command • 238
Interfaces • 36
Introduction • 1
IPv6 Command • 239
IPv6 Networking • 320
IPv6 Support Notes • 292
J
Java Runtime Environment (JRE) • 291
K
Keyboard Language Preference (Fedora Linux
Clients) • 294
Keyboard Macros • 59
Keyboard Options • 59
Keyboards • 293
KX2-832 and KX2-864 Extended Local Port
Recommended Maximum Distances • 273
KX2-832 and KX2-864 Standard and
Extended Local Port Settings • 188, 192
L
LAN Interface Settings • 32, 135
Launching MPC from a Web Browser • 51
Launching the Dominion KX II Remote
Console • 37
Left Panel • 40
Linux Settings (Red Hat 4) • 19
Linux Settings (Red Hat 9) • 18
Local Console Smart Card Access • 75, 242
Local Console USB Profile Options • 2, 243
Local Drives • 96
Local Port • 328
Local Port Administration • 250
Local Port Requirements • 278
Logging a User Off (Force Logoff) • 119
Logging In • 231, 232, 233
Logging Out • 50
Login Limitations • 193, 194
M
Macintosh Keyboard • 295
Maintenance • 209
Make Linux Settings Permanent • 21
Make UNIX Settings Permanent • 25
Manage Favorites Page • 46
Manageability • 339
Managing Favorites • 41, 45
Minimum System Requirements • 242, 278
Miscellaneous • 340
Modifying an Existing User • 118
Modifying an Existing User Group • 116
Modifying and Removing Keyboard Macros •
61
Mouse Modes when Using the Mac OS-X USB
Profile with a DCIM-VUSB • 107, 185
Mouse Options • 68
Mouse Pointer Synchronization • 69
Mouse Pointer Synchronization (Fedora) • 296
Mouse Settings • 14
Moving Between Ports of the Dominion KX II •
303
Multi-Platform Client Interface • 51
N
Name Command • 239
Naming Target Servers • 32
Naming the Power Strip in the KX II (Port
Page for Power Strips) • 161
Navigation of the CLI • 233, 234
Network Basic Settings • 133
Network Interface Page • 223
Network Settings • 25, 30, 32, 132, 133, 135
Network Speed Settings • 136, 281
Network Statistics Page • 223
Non-US Keyboards • 293
Note on Microsoft Active Directory • 34
Note to CC-SG Users • 34
O
Overview • 13, 52, 80, 83, 88, 100, 230, 240,
291
P
Package Contents • 12
Physical Specifications • 256
Ping Host Page • 226
Port Access Page • 2, 39, 42, 139, 165
Port Access Page (Local Console Server
Display) • 245
Port Action Menu • 43, 44, 247
Power Control • 331
Power Controlling a Target Server • 54
Power Strip (Rack PDU) Outlet Control • 83
Power Supply Setup • 27, 34, 154
Prerequisites for Using AKC • 2, 82
Prerequisites for Using Virtual Media • 91
Product Features • 9
Product Photos • 7
Proxy Mode and MPC • 303
Proxy Server Configuration for use with
Dominion KX II, MPC, VKC and AKC • 50
343
Index
R
RADIUS Communication Exchange
Specifications • 128
Rebooting • 219
Refresh Screen • 62
Related Documentation • 1
Relationship Between Users and Groups • 109
Remote Access • 307
Remote Authentication • 34, 190, 252
Remote Client Requirements • 279
Remote Connection • 274
Required and Recommended Blade Chassis
Configurations • 166, 168, 172, 182
Resetting the Dominion KX II Using the Reset
Button • 255
Resolving Fedora Core Focus • 297
Resolving Issues with Firefox Freezing when
Using Fedora • 297
Returning to the Dominion KX II Local Console
Interface • 249
Returning User Group Information • 283
Returning User Group Information from Active
Directory Server • 125
Returning User Group Information via RADIUS
• 128
Running a Keyboard Macro • 61
S
Scalability • 333
Security • 336
Security and Authentication • 241
Security Banner • 2, 207
Security Issues • 237
Security Management • 193
Security Settings • 193
Selecting Profiles for a KVM Port • 107
Servers • 322
Setting CIM Keyboard/Mouse Options • 62
Setting Network Parameters • 236
Setting Parameters • 235
Setting Permissions • 110, 112
Setting Permissions for an Individual Group •
114, 118
Setting Port Permissions • 110, 113, 116
Setting the Registry to Permit Write
Operations to the Schema • 284
Simultaneous Users • 240
Single Mouse Cursor • 72
344
Single Mouse Mode - Connecting to a
Dominion KX II Target Under CC-SG
Control Via VKC Using Firefox • 302
Smart Card Access in KX2 8 Devices • 243
Smart Card Readers • 276
Smart Cards (VKC, AKC and MPC) • 74
Smart Cards and CAC Authentication • 338
Software • 10
Special Sun Key Combinations • 248
Specifications • 27, 192, 256
Specifying Power Supply Autodetection • 33
SSH Access from a UNIX/Linux Workstation •
232
SSH Access from a Windows PC • 231
SSH Connection to the Dominion KX II • 231
SSL Certificates • 205
Standard Mouse Mode • 70
Step 1
Configure KVM Target Servers • 13, 14
Step 2
Configure Network Firewall Settings • 13,
25
Step 3
Connect the Equipment • 13, 26, 32, 157,
166, 168, 172
Step 4
Configure the Dominion KX II • 13, 29
Step 5 (Optional)
Configure Keyboard Language • 13, 35
Stopping CC-SG Management • 221
Strong Passwords • 131, 193, 195
Sun Solaris Settings • 21
Supported and Unsupported Smart Card
Readers • 74, 242, 276, 338
Supported Blade Chassis Models • 166, 168,
172, 179
Supported Browsers • 272
Supported CIMs and Operating Systems
(Target Servers) • 11, 29, 261
Supported CIMs for Blade Chassis • 166, 168,
172, 180
Supported Keyboard Languages • 275
Supported Operating Systems (Clients) • 11,
271
Supported Paragon CIMS and Configurations
• 2, 200, 267
Supported Protocols • 34
Supported Video Resolutions • 21, 25, 273,
274, 298
Supported Video Resolutions Not Displaying •
298
Index
SUSE Linux 10.1 Settings • 20
SUSE/VESA Video Modes • 297
Switching Between KVM Target Servers • 54
T
Target BIOS Boot Time with Virtual Media •
302
Target Server Connection Distance and Video
Resolution • 273, 274, 326
Target Server Requirements • 278
TCP and UDP Ports Used • 279
Telnet Connection to the Dominion KX II • 232
Terminology • 10, 14
Tiering - Target Types, Supported CIMS and
Tiering Configurations • 139, 141
Tips for Adding a Web Browser Interface •
168, 170, 172, 174, 175, 176
Tool Options • 76
Trace Route to Host Page • 226
Turning Outlets On/Off and Cycling Power •
84
U
Universal Virtual Media • 309
Unsupported and Limited Features on Tiered
Targets • 141
Updating the LDAP Schema • 283
Updating the Schema Cache • 287
Upgrade History • 219
Upgrading CIMs • 101, 185, 215
Upgrading Firmware • 216
USB Ports and Profiles • 298
USB Profile Management • 214, 215
USB Profiles • 56, 100, 185, 310
User Authentication Process • 130
User Blocking • 193, 196
User Group List • 109
User Groups • 108
User List • 117
User Management • 108, 241
Users • 117
Using Screenshot from Target • 67
Using the Dominion KX II Local Console • 240
Using Virtual Media • 93
Using Virtual Media via VKC and AKC in a
Windows Environment • 92
Virtual KVM Client • 38, 44, 52, 80, 100
Virtual KVM Client Version Not Known from
CC-SG Proxy Mode • 302
Virtual Media • 6, 87, 301
Virtual Media Connection Failures Using High
Speed for Virtual Media Connections • 302
Virtual Media Not Refreshed After Files Added
• 301
VKC and MPC Smart Card Connections to
Fedora Servers • 297
VKC Toolbar • 53
VKC Virtual Media • 73
VM-CIMs and DL360 USB Ports • 298
W
What's New in the Help • 2
Windows 2000 Composite USB Device
Behavior for Virtual Media • 301
Windows 2000 Settings • 16
Windows 3-Button Mouse on Linux Targets •
300
Windows 7, Windows XP, Windows 2003 and
Windows 2008 Settings • 15
Windows Vista Settings • 17
Working with Target Servers • 5, 36, 166
V
Video Modes and Resolutions • 297
Video Properties • 62
View Options • 79
345
U.S./Canada/Latin America
Monday - Friday
8 a.m. - 6 p.m. ET
Phone: 800-724-8090 or 732-764-8886
For CommandCenter NOC: Press 6, then Press 1
For CommandCenter Secure Gateway: Press 6, then Press 2
Fax: 732-764-8887
Email for CommandCenter NOC: tech-ccnoc@raritan.com
Email for all other products: tech@raritan.com
China
Europe
Europe
Monday - Friday
8:30 a.m. - 5 p.m. GMT+1 CET
Phone: +31-10-2844040
Email: tech.europe@raritan.com
United Kingdom
Monday - Friday
8:30 a.m. to 5 p.m. GMT
Phone +44(0)20-7090-1390
Beijing
France
Monday - Friday
9 a.m. - 6 p.m. local time
Phone: +86-10-88091890
Monday - Friday
8:30 a.m. - 5 p.m. GMT+1 CET
Phone: +33-1-47-56-20-39
Shanghai
Germany
Monday - Friday
9 a.m. - 6 p.m. local time
Phone: +86-21-5425-2499
Monday - Friday
8:30 a.m. - 5:30 p.m. GMT+1 CET
Phone: +49-20-17-47-98-0
Email: rg-support@raritan.com
GuangZhou
Monday - Friday
9 a.m. - 6 p.m. local time
Phone: +86-20-8755-5561
India
Monday - Friday
9 a.m. - 6 p.m. local time
Phone: +91-124-410-7881
Japan
Monday - Friday
9:30 a.m. - 5:30 p.m. local time
Phone: +81-3-3523-5991
Email: support.japan@raritan.com
Melbourne, Australia
Monday - Friday
9:00 a.m. - 6 p.m. local time
Phone: +61-3-9866-6887
Taiwan
Monday - Friday
9 a.m. - 6 p.m. GMT -5 Standard -4 Daylight
Phone: +886-2-8919-1333
Email: support.apac@raritan.com