Revised P1 Panelboards - Viking Electric Supply

Revised P1 Panelboards
Quick reference guide for selection and application
usa.siemens.com/panelboards
Introducing the Siemens Revised P1 Panelboard
Siemens is proud to introduce new,
innovative additions to the P1 series
of panelboards. The new “Revised
P1” Panelboard increases the
flexibility and customization options
available in Siemens already robust
panelboard line of products.
Siemens New “Revised P1” Panelboard
Siemens new Revised P1 panelboard adds additional strength
and flexibility, through the introduction of Non-Feed-Thru
options, to the already rugged, best-in-class line of panelboards.
By now offering both Feed-Thru (FT) and Non-Feed-Thru (NFT)
configuration options, Siemens offers even greater flexibility
and potential for customers to configure solutions that are
optimized to meet the many unique application and budgetary
requirements that today’s projects demand.
For applications where additional space for feed-thru lugs, a
subfeed breaker, or an SPD device isn’t required, the new NFT
P1 option is an ideal solution. The NFT Revised P1 features
an enclosure that is 6” shorter than a comparably configured
P1 with a FT design. Additionally, the NFT design can
accommodate 12 circuits more than the FT design panelboard
in the same sized cabinet.
Extended Circuitries
In addition to the new NFT options, Siemens P1 line of
panelboard products now offer extended circuit options that
take advantage of the elimination of the 42 circuit rule in
the National Electric Code. New, higher 54 and 66 circuit
ii
options allow for the elimination of a second cabinet in many
applications that would have previously required it.
The extended circuit options also facilitate the configuration
of P1 panelboard solutions for many applications that have
traditionally required the use of a P2 or P3 panelboard, thus
significantly reducing costs.
Adaptability
The new NFT design, coupled with the extended circuitries
offer additional options for adding circuits to existing Siemens
P1 with the Feed-Thru design. Where a 42 circuit FT P1
panelboard needs additional circuits but is not utilizing the
provided subfeed space, the interior can be replaced by a new
54 circuit NFT design interior. This saves the customer the cost
of a new enclosure and cover while still providing the option
for extended circuitries.
This selection and application guide is designed to provide
full insight into these and many other new features,
enhancements and options that will allow you to take full
advantage of the flexibility and customization options Siemens
offers to configure the P1 panelboard that best meets your
specific needs.
P1 Panelboards • Quick reference for selection and application
Revised P1 Panelboard 250 & 400A
• Invertability
All FT and NFT are invertable in field – Top-feed or Bottom-feed
• Flexibility
FT
400A MLO / MB
250A MLO/MB
20” Wide
20” Wide
ML (or) MB
Box Unit
Sizes Space
32”
18
38”
30
44”
42
50”
54
56”
66
Unit Box
Space Sizes
30
62”
42
68”
54
74”
Subfeed
FT Lugs
Subfeed Breakers
TVSS / SPD Devices
NFT
400A MLO / MB
250A MLO/MB
20” Wide
20” Wide
ML (or) MB
Box
Sizes
Unit
26”
Space
32”
18
38”
30
44”
42
50”
54
66
Unit Box
Space Sizes
30
56”
42
62”
54
68”
66
74”
P1 Panelboards • Quick reference for selection and application
iii
Revised P1 Panelboard 250A
Why move to NFT?
A)Smaller Box Size If Customer does not need Sub-feed
space or does not want to pay for it.
B) More Circuits needed If Customer does not need Sub-feed
space or does not want to pay for it.
• 6” shorter Enclosure than FT
• No Sub-Feed Space - pay for what you need only.
• 12 more circuits than FT in same box size
• No Sub-Feed Space- pay for what you need only.
New for Revised
Original & Revised
New for Revised
Original & Revised
New for Revised
250A
18 circuit NFT
250A
18 circuit FT
250A
30 circuit NFT
250A
30 circuit FT
250A
42 circuit NFT
B32 Enclosure
B32 Enclosure
B38 Enclosure
B38 Enclosure
B26 Enclosure
6” shorter than FT
6” shorter than FT
6” shorter than FT
Original & Revised
New for Revised
New for Revised
New for Revised
New for Revised
250A
42 circuit FT
250A
54 circuit NFT
250A
54 circuit FT
250A
66 circuit NFT
250A
66 circuit FT
B44 Enclosure
B44 Enclosure
B50 Enclosure
B50 Enclosure
6” shorter than FT
6” shorter than FT
New Options to Consider!
1)If a Customer has an existing 42 circuit FT
installed and needs additional circuits, the
interior can be replaced by a 54 circuit NFT.
Re-use the same Enclosure and front.
iv
2)If a Customer needs more than 42
circuits, you can use a 54 or 66 circuit
device and eliminate the second cabinet.
P1 Panelboards • Quick reference for selection and application
B56 Enclosure
Revised P1 Panelboard 400A
Why move to NFT?
A)Smaller Box Size If Customer does not need Sub-feed
space or does not want to pay for it.
B) More Circuits needed If Customer does not need Sub-feed
space or does not want to pay for it.
• 6” shorter Enclosure than FT
• No Sub-Feed Space - pay for what you need only.
400A
18 circuit NFT
New for Revised
400A
30 circuit NFT
• 12 more circuits than FT in same box size
• No Sub-Feed Space- pay for what you need only.
Original & Revised
400A
30 circuit FT
New for Revised
400A
42 circuit NFT
B62 Enclosure
B62 Enclosure
Original & Revised
400A
42 circuit FT
No Longer
Available
B56 Enclosure
6” shorter than FT
New for Revised
400A
54 circuit NFT
New for Revised
400A
54 circuit FT
New for Revised
400A
66 circuit NFT
6” shorter than FT
B68 Enclosure
400A
66 circuit FT
Not
Available
New Options to Consider!
1)If a Customer has an existing 42 circuit FT
installed and needs additional circuits, the
interior can be replaced by a 54 circuit NFT.
Re-use the same Enclosure and front.
2)If a Customer needs more than 42
circuits, you can use a 54 or 66 circuit
device and eliminate the second cabinet.
B68 Enclosure
6” shorter than FT
B74 Enclosure
B74 Enclosure
P1 Panelboards • Quick reference for selection and application
v
Revised P1 Panelboard FAQ’s
New Features and Options for “Revised P1” Offering compared to the “Original P1” panels
1. Non-Feed-thru (NFT) variations of the P1 Panels are now
available for Factory assembled only (not UPB):
6. BL/BQD and xGB (NGB/HGB/LGB) Main Breaker Usage is now
only available as a Back-Fed variation.
• Feed-Thru (FT) versions are versions with a Sub-feed space
that can be occupied by Feed-thru lugs, Subfeed Breaker or
an SPD device. All Original P1 devices were FT versions.
•
• Non-Feed-thru (NFT) versions do not have the Subfeed
space and therefore can fit into an enclosure 6“ smaller
than the FT version.
The NFT version will have a List price lower than the FT
version if configured the same.
• Both FT and NFT variations are fully invertible in the field and
can be used for either Top-feed or Bottom-feed applications.
2. Extended Circuits are now available:
Currently only 18, 30 and 42 circuits are available  54
and 66 “extended circuit” panels are added for Revised P1
a) P1-250A will have FT and NFT variations for all circuits:
18, 30, 42, 54 and 66 (xGB panels only available as FT)
b)P1-400A will have FT and NFT variations for 30, 42, 54
circuits only. (xGB panels only available as FT)
• The 66 circuit variation of 400A is only available in NFT
due to enclosure size limit of 74“ high.
• Also P1-400A will not be available in 18 circuit variations.
 Benefits: Many P2 and P3 applications can now move down to
the P1 platform!
3. New Neutral Configurations are now available:
• The new Neutral system has been developed to
accommodate the extended circuit variations without
increasing costs.
•
The new configuration is still a split neutral arrangement
with connections down either side of the interior, but it is
not full length as before. Neutral connections are still near
the breakers, but not adjacent to each breaker connection.
Many configurations have extra connections and some larger
configurations will allow adding more connections if needed.
7. New B-Phase Bus configuration eliminates “Hump-bus” design
•
The new flat bus with “B-Phase” connector has many
benefits. Increases productivity at the plant and allows
for replacement connectors in the field in case of a
“stripped” connection.
• Accessory kits for both CU and AL variations of the B-Phase
Connectors and A/C Connectors will be available for repair
purposes only.
8. xGB Breaker series expansion: NGB remains, but HGB and LGB
have been added
•
This addition to the Breaker line will now allow many
configurations to use the Revised P1 series or the P2 series
platforms instead of the P3 platform. Net pricing to customer
will be lower. See new ratings below:
NGB – 25,000 A IR Max. @ 480/277V AC / 100,000 A IR @ 240V AC
HGB – 35,000 A IR Max. @ 480/277V AC / 100,000 A IR @ 240V AC
LGB – 65,000 A IR Max. @ 480/277V AC / 100,000 A IR @ 240V AC
9. Misc. additional features:
a) New 750 kcmil AL/CU MLO will be available as an option for
400A. (CU cable limited to 600kcmil)
b)New 2/0 neutral kits are available. (used with 125A xGB
and others) (Only available as a field installable option)
c) New filler DFFP1 is introduced replacing QF3 (fits tighter
in deadfront)
4 Unassembled Panelboard Program Changes:
10. Misc. additional changes/notes:
• The UPB program will only get 54 circuit added to the
program for both P1-250A and P1-400A.
a) All DC voltage offerings are removed from scope of Revised
P1 devices.
• All UPB interiors will be the FT variation, the same as Original
P1. (400A - 18 circuit is no longer available)
 Customers will be moved to a P2 configuration for
these DC Voltage applications.
• All old Accessories/Kits will remain available for future needs
in Original P1 installations.
• New Accessories/Kits are available - most are same as old kits
with “A” added to end of part number. (see below)
5. Accessories and Kits for Revised P1 are replacing most of
the Original P1 Kits:
(most simply add an “A” to end of old kit number)
a) All Main/Subfeed Breaker Mounting kits are new. Both “Strap
Kits” and Kits with Breakers.
vi
The Revised P1 interior does not have “strap kits” for the BL/
BQD and xGB series of breakers to be used in the “Main” or
“Sub-Feed” positions. If needed to be used as a Main - we
now have a “Main Label Kit” that allows the placement of the
breaker in unit space to be used as the Main when labeled
properly. This does reduce unit space by “2 circuits” in a single
phase panel and by “3 circuits” in a 3-phase panel. Since 54 and
66 circuit panels are now available - this should not be an issue.
b)All Main Lug Kits are new.
c) All Neutral Lug Kits are new.
b)Limits on branch breaker size for 250A 18 circuit only:
• The new Revised P1 (18 circuit 250A only) is limited to 100A per
connection (200A per pair)
• Original P1 and the Revised P1 allows for the following:
(except as noted above)
1)100A per connection (200A per pair) for BL/BQD construction
2)125A per connection (250A per pair) for xGB construction
 Some of our competition limits the total to 140A per pair on
some panels.
P1 Panelboards • Quick reference for selection and application
Index
Revised P1 panelboards quick reference guide for selection and application
DescriptionPage
Introduction
ii
Revised P1 Panelboard Overview
iii
Revised P1 Panelboard FAQs
vi
Revised P1 Factory Assembled Panelboards
Revised P1 Unassembled Panelboards General Information 
2
New Revised P1 Unassembled Panelboards
Selection and Application
 2
Catalog Numbering System – (UPB Program)
General Specifications 
3
Distributor Stock
14
15
16
Catalog Numbering System – (factory assembled) 
4
Type P1 Unassembled Panelboards
(Revised P1 Introduced June 2014)
16
Application 
5
Lug Kits – Main or Feed Thru
17
Main Breaker Panel Size Selector – Revised P1
 5
Breaker Mounting Kits
17
Main Breaker Selection
 5
Copper Neutral Lug Kits – 250A
17
Main Lug Panel Size Selector – Revised P1
 6
2/0 Neutral Lug Kits – 250A and 400A
17
Branch Circuit Breakers
 6
200% Neutral Lug Kits – 250A
17
Subfeed Breakers
 7
200% Neutral Lug Kits – 400A
17
Breaker Mounting Kit
7
Miscellaneous Parts and Accessories
17
Lug Kits (Main or Feed-Thru)
7
Warehouse Stock/Unassembled
18
Copper Neutral Lug Kits – 250A
7
Main Breaker Mounting Kits with Breakers
18
2/0 Neutral Lug Kits – 250A and 400A
7
AFCI – Combination Type AFCI
18
200% Neutral Lug Kits – 250A
7
Switching Neutrals
18
200% Neutral Lug Kits – 400A
7
AFCI – Branch Feeder Type AFCI
18
Main Breaker Gutter Dimensions
8
Dual Function AFCI/GFCI............................................ 18
Main Lug End Gutter Dimensions
8
Branch Breakers Selection for P1
19
Side Gutter Wiring Space
8
BL Branch Breakers – 10,000A IR
19
Typical Catalog Numbers
9
HBL Branch Breakers – 65,000A IR
19
Main Lugs Only
9
GFCI Personnel Protection (5MA)
19
Main Circuit Breaker
9
BLH Branch Breakers – 22,000A IR
19
Standard Enclosures
9
BQD Branch Breakers – 14,000A IR
19
Standard Modifications
10
GB Family Branch Breakers
19
Miscellaneous Modifications
11
TPS Surge Protection Devices
20
Compression Lugs
11
Enclosure Modifications
11
Remote Switch Modifications
11
Dimensions
12
P1 Panelboards • Quick reference for selection and application
1
Type P1 Panelboards
The Revised P1 Panelboards are now available in both Feedthru (FT) and Non-Feed-thru (NFT) variations. There is a
savings of 6” of box height when a NFT version is selected
which eliminates the sub-feed space. The Sub-Feed Space
is where the Feed-thru Lugs, sub-feed breaker or a Surge
Protection Device (SPD) is installed. The interior part number
will end with a “T” for FT panels and will end with an “N” for
NFT panels.
The Revised P1 Panelboards also have Extended Circuit
variations with 54 circuits and 66 circuits available.
Feed-thru (FT) panels are pre-engineered to accept the most
common modifications without increasing box height. The
enclosure size is determined by the number of circuits as shown in
the Main Lug Table P1-5 or the Main Circuit Breaker Table P1-3.
All Revised P1 FT main lug or main breaker panelboards have space
built-in to accept either feed-thru lugs equal to the panel rating
(or) one subfeed circuit breaker up to 250 amperes (or) a surge
suppressor (SPD) without increasing box height. (When ordered
with sub-feed space the interior part # will end with a “T”).
Non-Feed-thru (NFT) panels do not have a sub-feed space and cannot
accept feed-thru lugs (or) sub-feed Breakers (or) SPD/TVSS devices.
(NFT panel interior part # will end in “N”).
Note the following features, all found in the innovative P1
lighting panelboards:
•Symmetrical 250A FT Interiors – To change from top to bottom feed (or vice-versa), simply invert the interior. The deadfront
labeling is always legible, even on the NFT panels when inverted.
- 400A are not symmetrical, but they are invertable.
•First in the Industry Ratings of 125 through 400A main lug and
main breaker. Field convertible from main lug to main breaker
and vice versa – with no increase in enclosure height.
• Field adaptability of feed-thru lugs (or) sub-feed circuit breaker
without increasing enclosure size. (FT panels only)
• Neutral system is field upgradeable to 200% capacity – another
industry first. (also 2/0 neutrals are available as a field install kit)
• Extended circuit panels are now available – up to 66 circuits.
- 18, 30, 42, 54 and 66 circuits for 250A (FT & NFT)
- 26”, 32”, 38”, 44”, 50” and 56” standard Enclosures are used.
- 30, 42 and 54 circuits for 400A (FT & NFT), also 66 circuit NFT
- 56”, 62”, 68” and 74” standard Enclosures are used.
• Suitable for use as service entrance given compliance with NEC.
• Bonding provisions are shipped with each panel.
• 240V and 480Y / 277V versions utilize identical boxes & fronts
Enclosure – Standard Type 1 enclosure is 20” wide x 5.75” deep.
Box Height is determined only by the number of circuits and FT or
NFT selection, not by main lug or main circuit breaker. See charts
P1-3 and P1-5 for box height.
Voltage – 480Y/277 Vac max. (Limited options for 600Y / 347V
Amperage – 400 amp max.
Short Circuit Rating – 200 KAIC max. symmetrical or equal to the
lowest rated device installed unless a series rating is indicated.
Panels with subfeed or feed-thru lugs without a main device,
circuit breaker or fusible unit, are limited to a three-cycle rating.
The three-cycle rating for the P1 panel is limited to 22 KAIC. Note
that the main device may be mounted remote from the panel.
Bussing – The P1 panel meets the majority of the markets
bussing requirements. The standard bussing is temperature rated
aluminum. The rating is per the requirements of UL 67– the
standard for panelboards. All aluminum bussing is tin-plated.
Optional bussing for the P1 panel is temperature rated copper.
The copper bus option for this panel is tin-plated.
Weight – Approximate
Total panelboard weight when filled with a normal quantity of
breakers and accessories is about 3 lbs. (1.36 kg) per inch (54g per
mm) of box height.
Table P1-1 – Box Material Gauge
Width
Height (inches)
Gauge Steel
20”(250A)
26, 32, 38, 44, 50, 56
#16 (#17 for endwalls)
(400A)
56, 62, 68, 74
#16 (#17 for endwalls)
Table P1-2 – Trim Material Gauge
20”(250A)
26, 32, 38, 44, 50, 56
#14
(400A)
56, 62, 68, 74
#14
Selection and Application
3 Easy Steps for Selecting a Siemens Revised P1 Panelboard (Note: Factory assembled panels are configurable in COMPAS)
Step 1
Determine voltage, system, amperage and
interrupting rating of branch devices, plus
modifications if any.
Example for standard lighting panelboard:
Amperage:
250A
Voltage:
208Y/120V
System:
3Ø4W
Main:
Main Lug
Branches:
10K AIR, 42-20/1
Modifications:None
Feed Location: Top
Sub-Feed req’d: Yes (as provision if wanted)
Mounting: Surface
Step 2
Create a catalog number by following the
Panelboard Catalog Numbering System on
2
page 4. The BL branch breakers were
selected from the branch breaker selection
table 1-6 on page 6.
1-P1C42ML250ATST (“T” indicates FT version)
42-20/1 BL
Note: If Sub-feed space is not needed
the NFT device can be used as below:
1-P1C42ML250ATSN (“N” indicates NFT
version) 42-20/1 BL
Step 3
Select enclosure size by the number
of circuits and FT/NFT as shown in the
panelboard dimension chart (Table P1-3)
on page 5.
1-P1C42ML250ATST
42-20 BL
Box size – 44” high
P1 Panelboards • Quick reference for selection and application
A unique feature of P1 FT panels is that
they can accommodate either feed-thru
lugs or one subfeed circuit breaker (up to
250A) without any addition to box height.
For our example changing the branch
circuits to 39-20/1 and 1-125/3, we have
the following:
1-P1C42ML250ATST
39-20/1 BL
1-125/3 QJ2
Box size – 44” high
The QJ2 subfeed was selected from Table
P1-7 of subfeed breakers on page 7.
The box height remains the same.
General Specifications
Service Entrance Equipment
When a panelboard is used as service entrance equipment, it must
be located near the point of entrance of building supply conductors.
In a main lugs only panel, the number of breakers or switches
directly connected to the main bus must be limited to six. In a panel
having a main breaker or main switch, the number of circuits are
not limited except as may be provided under other panelboard
requirements. Also, panels must include a connector for bonding
and grounding neutral conductor.
Lug Data
Space Required for Mounting of Double Panels
Integrated Equipment Short Circuit Rating
The term “Integrated Equipment Short Circuit Rating” refers to the
application of series connected circuit breakers in a combination
that allows some breakers to have lower individual interrupting
ratings than the available fault current. This is permitted as long as
the series combination has been tested and certified by UL.
Use two or more panelboards with feed-thru or subfeed lugs when:
Standards
NEC: 2014 (where accepted)
NEMA:PB1
UL:
67, 50 and 50E. Listed by Underwriter’s Laboratories, Inc.,
under “Panelboards” File #E2269, and #E4016. Meets
Federal Specification W-P-115c.
Wall
Wall
1.75in
(44mm)
Shown mounted on wall
1. Lighting and appliance panelboards are required with more
than 42 circuits in areas where the zone code has not been
accepted. (Note: 54 and 66 circuit panels are also available.)
2. More circuit mounting space is required than is provided in
the largest box size.
Feed Thru Lugs
Fig G-1
Wire Connectors
Standard wire connectors in Siemens panels are suitable for copper
or aluminum cables rated 60/75 degree. Copper main lugs are a
price-added option for most panel types and some Circuit Breakers
(check with Siemens sales for availability). It should be noted that
most copper lugs will only accept copper cables. Some applications,
100% rated devices in particular, require that the cable and
connectors be rated 90 degree but are sized to the 75 degree tables.
Standard ground connectors are also suitable for copper or aluminum
wire. Ground connector assemblies (EGK, IGK) have (7) 1/0 max. and
(15) #6 max. connections. The 1/0 holes are capable of connecting up
(3) #10 max. wires. The #6 holes can accept up to (2) #12 max. wires.
Copper ground assemblies (ECGK, ICGK) are rated for copper wire
only and have the same wiring capacity as the AL/CU connectors.
Standard neutrals, like standard main lugs, are also rated for copper
or aluminum wire. The neutral cross bar material follows the
selection bus. Copper neutral lugs are rated for copper cable only
and available as a price added option.
0.25in
(6mm)
Shown mounted in wall
Subfeed lugs or double lugs
Fig G-2 (Not available for P1 panels)
Panelboard 1
Feed
Thru
Lugs
Panelboard 2
Main
Lugs
Neutral
Panelboard 1
Panel
Panel
Panelboard 2
Panel
Panel
Main
Breaker
Neutral
Incoming Feeder Cables
Main
Lugs
Neutral
Neutral
Subfeed
Lugs
Main
Lugs
Incoming Feeder Cables
Feed-thru lugs are mounted at the opposite end of the main bus
from the main lugs or main breaker and are used to connect two
or more panelboards to the incoming feeder. The feeder cables are
brought into Panelboard 1 and connected to the main lugs or main
breaker. Cables interconnecting the two panelboards are connected
to the feed-thru lugs in Panelboard1 and are carried over the main
lugs in Panelboard 2. This arrangement could be reversed with the
main lugs located at the top and the feed-thru lugs at the bottom
of the panel. Subfeed lugs are mounted directly beside the main
incoming lugs and are used to connect two or more panelboards to
the incoming feeder. The feeder cables are brought into Panelboard
1 and connected to the main lugs. Another set of cables that are the
same size are connected to the subfeed lugs of Panelboard 1 and
are carried over the main lugs of Panelboard 2.
Note: P1 panelboards do not have Subfeed lugs available. If this
configuration is needed, move to a P2 (or) P3 panelboard.
P1 Panelboards • Quick reference for selection and application
3
Catalog Numbering System
Revised P1 panelboards
Type of Panel
P1
Voltage and System*
C = 208Y/120 3Ø 4 W Wye AC
E = 480Y/277 3Ø 4 W Wye AC
D = 240 3Ø 3 W Delta AC
F = 480 3Ø 3 W Delta AC
A = 120/240 1Ø 3 W Grounded Neutral AC
J = 240 1Ø 2 W No Neutral AC
M= 380/220 3Ø 4 W Wye AC
R = 415/240 3Ø 4 W Wye AC
S = 440/250 3Ø 4 W Wye AC
L = 600/347 3Ø 4 W Wye AC
T = 230 3Ø 3 W Delta AC
U = 120V AC 3Ø3W
K = 220/127 3Ø 4 W Wye AC
*For any voltage system not listed, check with sales for availability.
Circuits
18, 30, 42, 54, 66 (See table P1-3 and P1-5 for options available)
(Back-fed 1-phase will show: 16, 28, 40, 52, 64) (Back-fed 3-phase will show: 15, 27, 39, 51, 63)
Main Lug (ML), Main Breaker
(See Main Breaker Table coding below), Main Switch (MS)
Amperage
100–400A = P1
Bus Bus
CodeMaterial
Bus
Plating
P1
1
A
Temp rated AL.Tin-Plated •
B
750A/sq. in. AL.Tin-Plated n/a
C
Temp rated CU.Tin-Plated •
E
Temp rated CU. Silver-Platedn/a
F
Temp rated CU.Tin-Plated n/a
G
1000A/sq. in. CU.Tin-Plated
n/a
H
1000A/sq. in. CU.Silver-Plated n/a
• Indicates default for this bus type.
Feed Location
T = Top
B = Bottom
Mounting
S = Surface
F = Flush. Flush trims extend 1 1/2” beyond the base box dimensions on P1 panels.
Subfeed Space Indicator (for Revised P1 only)
T = Subfeed Space Included
Main Breaker Coding
Code
BL
BH
BR
BQ
B6
E4
E6
FD
FX
G2
G3
Breaker
Type
BL
BLH
BLR
BQD
BQD6
ED4
ED6
FD6
FXD6
HGB
LGB
Code
HB
H4
HF
H2
H6
H5
HL
HO
HP
Breaker
Type
HBL
HED4
HFD6
HFXD6
HJD6
HJXD6
HLD6
HLXD6
HLXD6H
Code
J6
JD
JX
JH
L6
LX
LH
NB
Breaker
Type
JD6
JXD2
JXD6
JXD6H
LD6
LXD6
LXD6H
NGB
Code
QJ
Q2
QH
Breaker
Type
QJ2
QJ2H
QJH2
Code
SX
SY
SJ
SH
S1
S2
SL
1 Standard bussing in P1 panels is tin-plated for aluminum and
copper. Standard bus is temperature rated to the maximum
amperage in the panel.
2 Not available for Revised P1 xGB interiors.
4
P1 Panelboards • Quick reference for selection and application
Breaker
Type
SHJD6
SHJD6H
SJD6
SJD6H
SCLD6
SHLD6
SLD6
N = No Subfeed Space2
Application
Type P1 Panelboards
Table P1-3 – Main Breaker Panel Size Selector – Revised P1
Max
Ampere
rating
Main
Breaker
Types
100
BL 2, BLH 2,
HBL 2, BQD 2
125
xGB 2
ED2, ED4
ED6, HED4
HED6
225
QJ2, QJH2,
QJ2-H
250
FXD6, FD6,
HFD6, HFXD6
400
JF6, JXD6,
HJD6,
HJXD6
Max #
Poles
FT 1
18
30
42
54
66
18
30
42
54
66
18
30
42
54
66
–
30
42
54
Max #
Poles
NFT
18
30
42
54
66
–
18
30
42
54
66
–
18
30
42
54
66
–
30
42
54
66
Dimensions in inches (mm)
Unit Space
Box Height
FT
NFT
B
A
A
–
9
15
21
27
33
–
9
15
21
27
33
–
9
15
21
27
33
–
15
21
27
9
15
21
27
33
–
9
15
21
27
33
–
9
15
21
27
33
–
15
21
27
33
26 (661)
32 (813)
38 (965)
44 (1118)
50 (1270)
56 (1423)
26 (661)
32 (813)
38 (965)
44 (1118)
50 (1270)
56 (1423)
26 (661)
32 (813)
38 (965)
44 (1118)
50 (1270)
56 (1423)
56 (1423)
62 (1575)
68 (1728)
74 (1880)
Weight in
Lbs. (kg)
90 (41)
105 (48)
120 (55)
135 (61)
150 (67)
165 (73)
95 (43)
110 (50)
125 (57)
140 (64)
155 (71)
170 (78)
95 (43)
110 (50)
125 (57)
140 (64)
155 (71)
170 (78)
172 (78)
190 (86)
208 (95)
226 (104)
Note: Main breakers use breaker connectors. For sizes, see breaker connector chart. 400 amp main breaker panel
has wire bending space for 600 kcmil cables as standard. 750 kcmil lugs may be required for 600 kcmil cable.
1 400A 66 circuit only available with non-feed thru versions.
2 BL, BLH, HBL, BQD, and xGB mount in unit space and count in max. # of poles.
Table P1-4 – Main Breaker Selection
Ampere
rating
100
125
225
250
400
Breaker
Types
BL (STD)
BLH
HBL
BQD
NGB (STD)
HGB
LGB
ED4 (STD)
HED4
QJ2 (STD)
QJH2
QJ2-H
FXD6 (STD)
FD6
HFD6
HFXD6
JXD2
JXD6 (STD)
JD6
HJD6
HJXD6
Max. Ir (kA) at
240 AC
10
22
65
65
100
100
100
65
42
10
22
42
65
65
100
100
65
65
65
100
100
480/277V AC
14
25
35
65
25
42
35
35
65
65
–
35
35
65
65
Main
Breaker
Code
BL
BH
HB
BQ
NB 3
G2 3
G3 3
E4
H4
QJ
QH
Q2
FX
FD
HF
H2
JD
JX
J6
H6
H5
Additional Trip Values
15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100
15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100
15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100
15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100
50, 60, 70, 80, 90, 100, 110, 125
50, 60, 70, 80, 90, 100, 110, 125
50, 60, 70, 80, 90, 100, 110, 125
50, 60, 70, 80, 90, 100, 110, 125
50, 60, 70, 80, 90, 100, 110, 125
60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250
70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250
70, 80, 90, 100, 150, 175, 200, 225, 250
70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250
300, 400
200, 225, 250, 300, 350, 400
200, 225, 250, 300, 350, 400
200, 225, 250, 300, 350, 400
200, 225, 250, 300, 350, 400
3 xGB interiors are not available as non-feed-thru without sub-feed space.
P1 Panelboards • Quick reference for selection and application
5
Application
Type P1 Panelboards
Table P1-5 - Main Lug Panel Size Selector - Revised P1
Maximum
Ampere rating
Max #
Poles
FT
18
30
42
54
66
–
30
42
54
125
(or)
250
400
Max #
Poles
NFT
18
30
42
54
66
–
30
42
54
66
Dimensions in inches (mm)
Unit Space
FT
NFT
Box Height
A
A
B"
–
9
26 (661)
9
15
32 (813)
15
21
38 (965)
21
27
44 (1118)
27
33
50 (1270)
33
–
56 (1423)
–
15
56 (1423)
15
21
62 (1575)
21
27
68 (1728)
27
33
74 (1880)
Weight in
Lbs. (kg)
90 (41)
105 (48)
120 (55)
135 (61)
150 (67)
165 (73)
120 (55)
135 (61)
150 (68)
165 (75)
MLO Connectors
Suitable for
(1) #6 AWG - 350 kcmil
(CU or AL)
AL (2) 1/0 - 250 kcmil or
(1) #2 AWG - 600 kcmil
CU (2) 1/0 - 4/0 or
(1) #2 AWG - 600 kcmil
Table P1-6 – Branch Circuit Breakers
Breaker
Type
BL
BLR
BL, HID
BLH
HBL
BLF
BLHF
BG 1
BLE
BLEH
BAF
BAFH
BQD
NGB 2, 3
HGB 2, 3
LGB 2, 3
Number
of Poles
1
2
3
2
1
2
1
2
3
1
2
3
1
2
1
2
2
3
1
2
1
2
1
1
1
2
3
1
2
3
1
2
3
1
2
3
Max. Interrupting Rating (kA)
120V
120/240V
240V
10
–
–
–
10
–
–
–
10
–
–
10
10
–
–
–
10
–
–
22
–
–
22
–
–
–
22
–
65
–
–
65
–
–
–
65
10
–
–
–
10
–
22
–
–
–
22
–
10
–
–
–
10
–
10
–
–
–
10
–
22
–
–
–
22
–
10
–
–
22
–
–
–
65
–
–
65
–
–
–
65
100
–
–
–
100
100
–
100
100
100
–
–
–
100
100
–
100
100
100
–
–
–
100
100
–
100
100
277V
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
14
–
–
25
–
–
35
–
–
65
–
–
480/277V
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
14
14
–
25
25
–
35
35
–
65
65
Available Trip Values
15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 70
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
15, 20, 30, 40, 50, 60, 70, 90, 100
15, 20, 30
15, 20, 30
15, 20, 30, 40, 50, 55, 60, 70
15, 20, 30, 40, 50, 60, 70, 90, 100
15, 20, 30, 40, 50, 60, 70, 80, 90, 100
15, 20, 30, 40, 50
15, 20, 30, 40, 50, 60, 70
15, 20, 30, 40, 50, 60, 70, 80, 90, 100
15, 20, 30
15, 20, 30, 40, 50, 60
15, 20, 30
15, 20, 30, 40, 50, 60
15, 20, 30
15, 20, 30
15, 20, 30
15, 20, 30, 40, 50, 60
15, 20, 30
15, 20, 30, 40, 50, 60
15, 20
15, 20
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100, 125 3
1 Two-pole breaker is one phase and neutral. Three-pole is two phases and neutral.
2 P1 panel with NGB/HGB/LGB branch devices will not accept BL or BQD frames in the same panel as branch devices.
3 The New Revised P1 (18 circuit 250A only) is limited to 100A per connection (200A per pair) when installing Branch Breakers across from one another.
All other configurations allow 125A per connection max. (250A per pair max.)
NOTE: BL, HBL and BQD breakers are mounted in common mountings in 3” or (6) pole increments.
6
P1 Panelboards • Quick reference for selection and application
Application
Type P1 Panelboards
Table P1-7 – Subfeed Breakers
Breaker
Type
Number
of Poles
QJ2
QJH2
QJ2H
HQJ2
ED4
HED4
FXD6
FD6
HFD6
HFXD6
2, 3
2, 3
2, 3
2, 3
2, 3
2, 3
2, 3
2, 3
2, 3
2, 3
Max. Interrupting Rating (kA)
240V
480Y/277V
10
–
22
–
42
–
100
–
65
18
100
42
65
35
65
35
100
65
100
65
Table P1-8 – Breaker Mounting Kit
Main or Subfeed Strap Kit w/o Breaker
Amp
Breaker
Rating Frames
100A
BQD
BL, BLH, HBL
100A
125A
ED4, ED6, HED4, HED6
125
QJ2, QJH2, QJ2-H
225
FXD6, FD6, HFD, HFXD6
250
400
NGB, HGB, LGB
1
JXD6, JD6
HJD6, HJXD6
Service
3 Phase
1 Phase
3 Phase
1 Phase
3 Phase
1 Phase
3 Phase
1 Phase
3 Phase
1 Phase
3 Phase
1 Phase
3 Phase
Original P1
Catalog
Number
MBKBC3
MBKBL1
MBKBL3
MBKNB1
MBKNB3
MBKED1
MBKED3
MBKQJ1
MBKQJ3
MBKFD1
MBKFD3
MBKJD1
MBKJD3
Available Trip Values
60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 70, 80, 90, 100, 110, 125
15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 70, 80, 90, 100, 110, 125
70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250
70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250
70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250
70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250
Table P1-10 – Copper Neutral Lug Kits – 250A
Revised P1
Catalog
Number
Use Back-fed
Main Label
Kit # MBKBFA 2
(includes Neutral
Lug, “MAIN” label
and instructions)
MBKED1A
MBKED3A
MBKQJ1A
MBKQJ3A
MBKFD1A
MBKFD3A
MBKJD1A
MBKJD3A
No. of
Circuits
18
30
42
54, 66
Description
2 or 4 Branch Neutral Strips,
1 Main Neutral Lug, Hardware
Original P1
Catalog
Number
CNLK18
CNLK30
CNLK42
–
Revised P1
Catalog
Number
Use 30 ckt kit
CNLK30A
CNLK42A
CNLK54A
Table P1-10A – 2/0 Neutral Lug Kits – 250A and 400A
No. of
Circuits
18
30
42
54, 66
Description
2 or 4 Branch Neutral Strips,
Hardware
Original P1
Catalog
Number
–
–
–
–
Revised P1
Catalog
Number
Use 30 ckt kit
LNLK30A
LNLK42A
LNLK54A
1 400 amp kit is for main—only, not allowed for subfeed breaker.
2 Back-fed main occupies branch space.
Table P1-9 – Lug Kits (Main or Feed-Thru)
Amp
Wire Range
Rating Matl. (includes Neutral)
250
400
400
AL
CU
AL
CU
AL
Service
1 Phase
(1) #6 AWG350 kcmil (CU or AL)
3 Phase
1 Phase
(1) #6 AWG350 kcmil (CU or AL)
3 Phase
1 Phase
(2) 1/0 - 250 kcmil
or (1) #2 AWG-600 kcmil 3 Phase
1 Phase
(2) 1/0 - 4/0
or (1) 1/0 - 600 kcmil
3 Phase
1 Phase
AL 1/0-750 kcmil
(max. 600 kcmil CU wire) 3 Phase
Table P1-11 – 200% Neutral Lug Kits – 250A
Original
Catalog
Number
MLKA1
MLKA3
MLKC1
MLKC3
4MLKA1
4MLKA3
4MLKC1
4MLKC3
–
–
Revised P1
Catalog
Number
MLKA1A
MLKA3A
MLKC1A
MLKC3A
4MLKA1A
4MLKA3A
4MLKC1A
4MLKC3A
4MLKA1B
4MLKA3B
No. of
Circuits
18
30
42
Description
2 or 4 Branch Neutral Strips,
2 Main Neutral Lugs, Hardware
54, 66
Original P1
Catalog
Number
Revised P1
Catalog
Number
2NLK30
2NLK30A
2NLK42
2NLK42A
–
2NLK54A
2NLK18
Use 30 ckt kit
Table P1-12 – 200% Neutral Lug Kits – 400A
No. of
Circuits
Description
Original P1 Revised P1
Catalog
Catalog
Number
Number
18
42NLK18
N/A
30
42NLK30
42NLK30A
42NLK42
42NLK42A
–
42NLK54A
42
54, 66
2 or 4 Branch Neutral Strips, 1 Main
600 kcmil Neutral Lug, Hardware
P1 Panelboards • Quick reference for selection and application
7
Application
Type P1 Panelboards
Table P1-13 – Main Breaker Gutter Dimensions Inches (mm)
Main
Breaker
BL, BLH, HBL, BQD 2
NGB, HGB, LGB 2
ED2, ED4, ED6, HED4
QJ2, QJH2, QJ2-H
FD6, FXD6, HFD6, HFXD6
JD6, JXD6 1
Max. Interrupting Rating (kA)
20” wide box
24” wide box
8.500 (216) 3
10.500 (267) 3
8.000 (203) 3
10.000 (254) 3
6.125 (156)
8.125 (206)
6.500 (165)
8.500 (216)
5.250 (133)
7.250 (184)
15.000 (381)
15.000 (381)
Neutral Location
20” wide box
10.500 (267)
10.500 (267)
10.500 (267)
10.500 (267)
10.500 (267)
26.500 (674)
1 JD frame mounted vertically.
125
250
400
Neutral Location
20” wide box
10.500 (267)
10.500 (267)
26.750 (680)
24” wide box
10.500 (267)
10.500 (267)
26.750 (680)
NOTE: Feed-thru lug and neutral wire bending space is 15.000” and 16.250” respectively on 400A panel.
Table P1-15 – Side Gutter Wiring
Space Inches (mm) (Fig P1-1)
Panel
Width 20”
B2
5.500 (140)
7.500 (191)
C2
5.000 (127)
7.000 (178)
D
6.125 (156)
8.125 (206)
E
6.500 (165)
8.500 (216)
FXD6, FD6, HFD6, HFXD6
F
5.250 (133)
7.250 (184)
Panel Width
20 in. (508 mm)
For all Revised P1 panels using BL/BQD or xGB breakers as mains in back-fed position, use
this chart for wiring space.
Feed-Thru (FT)
8
1 Replacement parts only.
8.375 (213)
1 Subfeed mounting limit 1 per panel.
2
DFFP1
Fig P1-1
Reference
Letter
6.375 (167)
EGK
ECGK
IGK
ICGK
EWK1
EWK2
EBF1
P1SCRWS
P1CONBPHCU 
P1CONBPHAL 
P1CONACPHCU 
P1CONACPHAL 
Panel
Width 24”
Optional
A2
NBK03
NBK06
Table P1-14 – Main Lug End Gutter Dimensions Inches (mm)
24” wide box
9.500 (242)
9.500 (242)
25.500 (648)
Description
Bonding Kit for 250A max. Original P1 Panels
Bonding Kit for 250A max. Revised P1 Panels
Bonding kit for S1/S2 400 & 600
Bonding kit
Interior Adjusting Kit
Directory Card Holder
Directory Card
NEMA Instruction Book
Number Strips 1–42 . Stick-on type;
Use w/ P1 series Panels
Number Strips 43–84. Stick-on type;
Use w/ P1 series Panels
Number Strips 85–126. Stick-on type;
Use w/ P1 series Panels
Number Strips 127–168. Stick-on type;
Use w/ P1 series Panels
AL Ground Bus 44 Connections
CU Ground Bus 44 Connections
Insulated AL Ground Bus
Insulated CU Ground Bus
End Wall Kit with Knockouts (20" W x 5.75" DP)
End Wall Kit with Knockouts (24" W x 7.75" DP)
NEB/HEB Filler Plate
Package of 42 breaker mounting screws for P1
1" Branch circuit filler plate (suitable for replacing
QF3 in P1 thru P5 Panelboards and Switchboards)
Connector kit – 6 pcs. B-phase Copper
Connector kit – 6 pcs. B-phase Aluminum
Connector kit – 6 pcs. A or C-phase Copper
Connector kit – 6 pcs. A or C-phase Aluminum
NBK05
3 These dimensions are for Original P1 as a reference only, not for Revised P1.
End Gutter
20” wide box
9.500 (242)
9.500 (242)
25.500 (648)
Catalog #
BK1
BK1A
BK2
BK3
IMK1
11-1824-01
12-1110-01
11-1056-01
NBK04
For Revised P1, use Side Gutter Wiring Specs Table P1-15.
These are back-fed main breakers.
2
Amp
Rating
Miscellaneous Parts and Accessories
Non-Feed-Thru (NFT)
P1 Panelboards • Quick reference for selection and application
Example of Back-fed xGB Main breaker installed
Typical Catalog Numbers
Type P1 Panelboards
Shown with Standard Mains, Top Fed and Surface Trim
Catalog number is for aluminum main bus. For optional copper main
bus change “A” in position 11 to “C”.
Panels are top feed, surface mounted. For bottom feed, change
“T” in position 12 to “B”. For flush mounting, change “S” in
position 13 to “F”.
Table P1-16 – Main Lugs Only
Main Lug Only
Max Panel Max
Amp
1-Pole
Rating
Circuits
125
250
400
Box
Height
(in.)
Original P1 –
Subfeed Space
125 2
225
250
400
Original P1 –
Subfeed Space
Revised P1 –
Subfeed Space 1, 3, 4
208Y/120V 3-Phase 208Y/120V 3-Phase 120/240V 1-Phase
4-Wire Catalog #
4-Wire Catalog #
3-Wire Catalog #
120/240V 1-Phase
3-Wire Catalog #
480Y/277V 3-Phase
4-Wire Catalog #
480Y/277V 3-Phase
4-Wire Catalog #
Original P1 –
Subfeed Space
18
30
42
54
66
18
30
42
54
66
18
30
42
54
66 2
32
38
44
50
56
32
38
44
50
56
56
62
68
74
74 2
P1C18ML125ATS
P1C30ML125ATS
P1C42ML125ATS
N/A
N/A
P1C18ML250ATS
P1C30ML250ATS
P1C42ML250ATS
N/A
N/A
P1C18ML400ATS
P1C30ML400ATS
P1C42ML400ATS
–
–
P1C18ML125ATST
P1C30ML125ATST
P1C42ML125ATST
P1C54ML125ATST
P1C66ML125ATST
P1C18ML250ATST
P1C30ML250ATST
P1C42ML250ATST
P1C54ML250ATST
P1C66ML250ATST
–
P1C30ML400ATST
P1C42ML400ATST
P1C54ML400ATST
P1C66ML400ATSN 2
P1A18ML125ATS
P1A30ML125ATS
P1A42ML125ATS
N/A
N/A
P1A18ML250ATS
P1A30ML250ATS
P1A42ML250ATS
N/A
N/A
P1A18ML400ATS
P1A30ML400ATS
P1A42ML400ATS
–
–
P1A18ML125ATST
P1A30ML125ATST
P1A42ML125ATST
P1A54ML125ATST
P1A66ML125ATST
P1A18ML250ATST
P1A30ML250ATST
P1A42ML250ATST
P1A54ML250ATST
P1A66ML250ATST
–
P1A30ML400ATST
P1A42ML400ATST
P1A54ML400ATST
P1A66ML400ATSN 2
P1E18ML125ATS
P1E30ML125ATS
P1E42ML125ATS
N/A
N/A
P1E18ML250ATS
P1E30ML250ATS
P1E42ML250ATS
N/A
N/A
P1E18ML400ATS
P1E30ML400ATS
P1E42ML400ATS
–
–
P1E18ML125ATST
P1E30ML125ATST
P1E42ML125ATST
P1E54ML125ATST
P1E66ML125ATST
P1E18ML250ATST
P1E30ML250ATST
P1E42ML250ATST
P1E54ML250ATST
P1E66ML250ATST
–
P1E30ML400ATST
P1E42ML400ATST
P1E54ML400ATST
P1E66ML400ATSN 2
18
30
42
54
66
18
30
42
54
66
18
30
42
54
66
18
30
42
54
66
18
30
42
54
66 2
32
38
44
50
56
32
38
44
50
56
32
38
44
50
56
32
38
44
50
56
56
62
68
74
74 2
P1C18BL100ATS
P1C30BL100ATS
P1C42BL100ATS
–
–
P1C18NB125ATS
P1C30NB125ATS
P1C42NB125ATS
–
–
P1C18QJ225ATS
P1C30QJ225ATS
P1C42QJ225ATS
–
–
P1C18FX250ATS
P1C30FX250ATS
P1C42FX250ATS
–
–
P1C18JX400ATS
P1C30JX400ATS
P1C42JX400ATS
–
–
P1C18BL100ATST
P1C30BL100ATST
P1C42BL100ATST
P1C54BL100ATST
P1C66BL100ATST
P1C18NB125ATST
P1C30NB125ATST
P1C42NB125ATST
P1C54NB125ATST
P1C66NB125ATST
P1C18QJ225ATST
P1C30QJ225ATST
P1C42QJ225ATST
P1C54QJ225ATST
P1C66QJ225ATST
P1C18FX250ATST
P1C30FX250ATST
P1C42FX250ATST
P1C54FX250ATST
P1C66FX250ATST
–
P1C30JX400ATST
P1C42JX400ATST
P1C54JX400ATST
P1C66JX400ATSN 2
P1A18BL100ATS
P1A30BL100ATS
P1A42BL100ATS
–
–
–
–
–
–
–
P1A18QJ225ATS
P1A30QJ225ATS
P1A42QJ225ATS
–
–
P1A18FX250ATS
P1A30FX250ATS
P1A42FX250ATS
–
–
P1A18JX400ATS
P1A30JX400ATS
P1A42JX400ATS
–
–
P1A18BL100ATST
P1A30BL100ATST
P1A42BL100ATST
P1A54BL100ATST
P1A66BL100ATST
–
–
–
–
–
P1A18QJ225ATST
P1A30QJ225ATST
P1A42QJ225ATST
P1A54QJ225ATST
P1A66QJ225ATST
P1A18FX250ATST
P1A30FX250ATST
P1A42FX250ATST
P1A54FX250ATST
P1A66FX250ATST
–
P1A30JX400ATST
P1A42JX400ATST
P1A54JX400ATST
P1A66JX400ATSN 2
P1E18BD100ATS
P1E30BD100ATS
P1E42BD100ATS
–
–
P1E18NB125ATS
P1E30NB125ATS
P1E42NB125ATS
–
–
P1E18FX250ATS
P1E30FX250ATS
P1E42FX250ATS
–
–
P1E18FX250ATS
P1E30FX250ATS
P1E42FX250ATS
–
–
P1E18JX400ATS
P1E30JX400ATS
P1E42JX400ATS
–
–
P1E18BD100ATST
P1E30BD100ATST
P1E42BD100ATST
P1E54BD100ATST
P1E66BD100ATST
P1E18NB125ATST
P1E30NB125ATST
P1E42NB125ATST
P1E54NB125ATST
P1E66NB125ATST
P1E18FX225ATST
P1E30FX225ATST
P1E42FX225ATST
P1E54FX225ATST
P1E66FX225ATST
P1E18FX250ATST
P1E30FX250ATST
P1E42FX250ATST
P1E54FX250ATST
P1E66FX250ATST
–
P1E30JX400ATST
P1E42JX400ATST
P1E54JX400ATST
P1E66JX400ATSN 2
Table P1-18 – Standard Enclosures
Box
Height
(in.)
26
32
38
44
50
56
62
68
74
Note: Original P1 was produced until 2015 and in January the revised P1 was
introduced. All interior numbers that end with “T” or “N” are the new Revised
interiors. T” at end of catalog number indicates there is a Subfeed area available.
“N” at end of catalog number indicates there is no Subfeed area available.
Revised P1 –
Subfeed Space 1, 3
Table P1-17 – Main Circuit Breaker
100
Revised P1 –
Subfeed Space 1, 3
Replace fifth and sixth position in panelboard catalog number, with
alternate main breaker code.
Catalog Number
Type 1 Standard Trim
Box
Surface
B26
S26B
B32
S32B
B38
S38B
B44
S44B
B50
S50B
B56
S56B
B62
S62B
B68
S68B
B74
S74B
Flush
F26B
F32B
F38B
F44B
F50B
F56B
F62B
F68B
F74B
Type 3R
NR26
NR32
NR38
NR44
NR50
NR56
NR62
NR68
NR74
Type 3R/12
WP26
WP32
WP38
WP44
WP50
WP56
WP62
WP68
WP74
1 For all products without subfeed space
- change “T” at end to “N” and reduce
box size by 6”.
2 No sub-feed space only for 400A 66 circuit.
3 BL/BQD/GB Type Mains are only available as Back-Fed. No kits are available for use in Main or Sub-feedspace. (GB Type includes NGB, HGB and LGB Breakers). These breakers take up branch circuit space.
4 xGB interiors are not available as Non-Feed-Thru,
without Subfeed Space.
P1 Panelboards • Quick reference for selection and application
9
Standard Modifications
Type P1 Panelboards
Panel Options
Enclosures
• Extra gutter to sides or ends of the can
• 24” wide boxes
• Hinged trims
• Door-in-door trims
• Screw to the box trims
• Piano hinge trims
• Painted boxes
• Custom colors
• Increase gauge trims and boxes (See pages 12-13)
• Stainless steel trims and boxes
• Type 1 enclosures (Std 16 Gage / Optional 14 or 12 Gage)
• NEMA 3R/12 enclosures
• NEMA 4 enclosures
Panel Modifications
Enclosures
• Main Bus
Standard main bus is tin-plated aluminum. For copper main bus, add from the table for each panel. Includes copper neutral cross bar. For copper neutral branch lugs, see miscellaneous.
• Compression lug for MLO 1
• Contactor mains - Mount in 23” enclosure ahead of panel.
- Asco 920 through 225 amps 3
- Asco 911 through 150 amps 3
- Siemens LEN through 30 amps 3
• Branch and main breaker accessories
- Handle blocks
- Handle locks • Feed-thru lugs 1
Cannot be used in conjunction with SPD/TVSS or subfeed
breakers. Do not add height to the panel.
Feed-thru
Lugs Amp
Rating
250
400
Type
Connector
CU/AL Range
AL/CU
Mechanical
(1)–#6 AWG350 kcmil
CU
Mechanical
(1)–#6 AWG350 kcmil
AL/CU
Compression
(1)–#6 AWG350 kcmil
AL/CU
AWG Mechanical
(2)–#1/0 250 kcmil or
(1)–#2 AWG600 kcmil
CU
AL/CU
Compression
10
(1)–1/0-600 kcmil
(2)-1/0-4/0
(1) 400-600 kcmil AL
(1) 400-500 kcmil CU
• NEMA 4X enclosures
• Special Keyed Locks (Keys are not supplied)
• Panel skirts
• Gaskets between trim and box
TEY
TEU1
Cat 60
LL803
LL806
All fit Fast-Latch Front
Yale 47 (NYC)
National C413A
Beck Lock 7-pin tumbler
Southco 1 4 Fastener
Corbin 1001 FAB7
Special non-Fast-Latch
• 200% neutral 1
• Copper lugs, mechanical line and branch neutral 1
• Bus mounted SPD/TVSS 1
• Service entrance labeling
• Grounding of Panelboards
Ground Bars except for brazed to box are shipped with
the panel interior factory mounted.
- Non-Insulated Equipment Ground Bar – Standard
- Copper Non-Insulated Ground Bar
- AL Insulated Equipment Ground Bar
- CU Insulated Equipment Ground Bar
- Ground Bar Brazed to Box (recommended for painted boxes)
• Shunt Trip on Main or Branch
BL2, BLH 2, HBL2, BQD 2, xGB 2 as branch use 1” unit space for shunt trip.
QJ2, QJ2-H, QJH2, ED2, ED4, ED6, HED4, HED6, HHED6, FD6, FXD6, HFD6
HFXD6, JXD6, JD6, HJD6, HJXD6, HQJ2H
• Remote control switches – 480V AC max. mounted in
a 23” enclosure to be cable connected to the panel.
• Time Clocks – mounted in a 23” enclosure to be cable
connected to the panel. Tork time clock can be supplied and
mounted in panelboard cabinet.
Time Clock Information and Options
Time Clock (1- or 2-Pole, Single or Double Throw Contacts,
3-Pole Single Throw) 277V Maximum with Plain Dial
Options:
Astronomical Dial
An Omitting Device
Reserve Power or Carryover
Space and Mounting Provisions Only
Note: Specify copper or aluminum cable.
1 Do not increase panel or enclosure size.
2 Accessories on 1” pole breakers (BL, BQD, xGB, ED) will take 1” unit space.
3 External to the panel, supplied in a separate enclosure.
P1 Panelboards • Quick reference for selection and application
Miscellaneous Modifications
Type P1 Panelboards
Compression Lugs
Table P1-19 – Lugs
Amp
Rating
125
250
Style
MLO
Main Breaker
Breaker
Type
Compression
Connectors
Box Height
Addition
N/A
(1) #6 AWG - 350 kcmil
None
400
N/A
125
ED4, ED6, HED4
225
QJ2, QJH2, QJ2H
250
FXD6, HFD6
(1) 400 - 600 kcmil AL
(1) 400 - 500 kcmil CU
(1) #14 AWG - 2/0
(1) #6 AWG - 350 kcmil
CU or AL
(1) #6 AWG - 350 kcmil
CU or AL
None
Box must go to 24” wide
Box must go to 24” wide for All breakers
Box must go to 24” wide for All breakers
Note: Standard compression lugs used for P1 panels are range taking lugs and require a particular crimping tool (tool is Hubbell/Anderson Versa Crimp VC6 for 250A) to accommodate the range. Consult factory for information. 200% neutral not available with compression lugs. xGB breakers cannot accommodate
compression lugs. (For 400A tool use Hubbell/Anderson Versa Crimp VC6FT/VC7FT - see instruction sheet for details.)
Enclosure Modifications
NEMA-4–Water Tight, Dust Tight, Steel
Enclosure (Actual NEMA-4 enclosure is
larger than standard Type 1 enclosre. See
chart below for reference to approximate
actual size.)
NEMA-4X For Type P1
Water Tight, Dust Tight and Corrosion Resistant
(consult plant to verify actual enclosure size)
Table P1-20
Table P1-21
Standard
Box Height
(in inches)
Actual NEMA 4
Enclosure Size
Enclosure – Stainless Steel
Size (inches) (304SS is standard)
Enclosure Fiberglass
Size (inches)
H
W
D
H
W
D
H
W
D
Catalog
Number
32
32
20
8
B4X26
26
20
5.75
36
30
8
38
42
30
8
B4X32
32
20
5.75
36
30
8
38
20
5.75
48
36
12
44
48
36
8
B4X38
56
60
36
10
B4X44
44
20
5.75
48
36
12
B4X50
50
20
5.75
60
36
12
B4X56
56
20
5.75
60
36
12
B4X62
62
20
5.75
B4X68
68
20
5.75
B4X74
74
20
5.75
Note: Larger NEMA 4 enclosures are not available.
Note: 316SS is available as an option – must be specified.
Remote Switch Modifications
Table P1-22 – Control Power Transformer
Table P1-23 – Applications for a Remote Switch
Size
VA Relay
Switch Type
Modification
0, 1
50
920
Mounts in 23” relay cabinet as a main only
2
75
LEN
30A mounts in 23” relay cabinet as a main only
3
150
4
250
Table P1-24 – Remote Control
Switch Modification
Description
Auxiliary Contacts (mounted, not wired)
2-Wire Control
P1 Panelboards • Quick reference for selection and application
11
Dimensions
Type P1 Panelboards
Type 1 BoxType 1 Box
Box is symmetrical
Box is symmetrical
Type 1 Box
Box is symmetrical
26 in.,
[ 660 ]
, 50 in.
[1270]
, 74 in.
[1880]
26 in.,
[ 660 ]
, 50 in.
[1270]
, 74 in.
[1880]
³⁄₄ in.
[19 ]
20 in.
[ 508 ]
5.75 in.
[ 146 ]
(UL approved construction. 16 Gage Steel or equivalent alternate Construction.
14 or 12 Gage is available as an optional special order.)
Type 3R and 3R/12 Box
³⁄₄ in.
[19 ]
Flush Mounting
Type 3R and
BoxBox
Type3R/12
3R and 3R/12
26 in.,
[ 660 ]
, 50 in.
[1270]
, 74 in.
26]in.,
[1880
[ 660 ]
, 50 in.
[1270]
, 74 in.
[1880]
1 Dimensions are interior of the box. Add 5/8” to width for
1 Dimensions areabsolute
Add
to height
for absolute
dimension.
interior ofdimension.
the box. Add
5/8"1/8”
to width
for absolute
dimension.
Add
(UL approved construction. 16 Gage Steel Can with 14 Gage 1/8"
front
to height for absolute dimension.
or similar approved construction.)
Dimensions shown
in inchesshown
and millimeters
].are interior
1 Dimensions
of the[box.
Dimensions
in inches[ and
millimeters
]. Add 5/8" to width for absolute dimension. Add
1/8" to height for absolute dimension.
Dimensions shown in inches and millimeters [ ].
12
P1 Panelboards • Quick reference for selection and application
Dimensions
Panelboards - Trim / Front
Standard Trim (FAS-Latch) Typical Dimensions (Hinges available as shown on right side only)
(Typical 14 Gage Steel construction or UL approved equivalent)
Standard Trim (FAS-Latch)
(14 Gage Standard - no options)
(UPB includes surface or flush versions
of this style in chart on page 14. Other
special fronts below are not part of the
UPB program.)
# of
Hinges
Surface
Flush
Box
Size
A
A
26
26
27.5
2
32
32
33.5
2
38
38
39.5
2
44
44
45.5
3
50
50
52.5
3
# of
Hinges
Surface
Flush
Box
Size
A
A
56
56
57.5
3
62
62
63.5
3
68
68
69.5
3
74
74
75.5
3
Also available
• Screw to Box Trim
(14 Gage Std./12 Gage Optional)
Door in Door Front (14 Gage
Standard /12 Gage optional)
Hinged Front
• Piano Hinge Trim
(not available for 10 Gage)
a) Screw to box with Piano Hinge Door
b) Hinge to Box with Piano Hinge and
Piano Hinge Door
c) Door-in-Door with Piano Hinge,
Both Doors
P1 Panelboards • Quick reference for selection and application
13
New Revised P1 Unassembled Panelboards
To better serve the needs of customers, Authorized Siemens Unassembled Panelboard Distributors offer product
flexibility, quicker job turn-around, and affordable pricing. All Siemens unassembled panelboards are fully backed for
high quality, trouble-free operation and are labeled as Suitable for use as Service Entrance Equipment.
Flexibility and ease of assembly:
Customer oriented design creates installation convenience.
For all of its one-of-a-kind features, the P1 panelboard is also
designed to be extremely userfriendly. For instance, field
convertible main breaker and main lug kits, (through 400 amps),
will allow you to switch from main lug to main breaker, and vice
versa with no change in box size or additional cabling. Plus, lay-in
construction (for 250 A CU) and/or removable lugs make wiring
the main and neutral lugs easier and faster. To further speed
wiring, as well as reduce clutter, the P1 panel also features a split
neutral design and branch neutral connections which are closer
to the breakers than competitors. Additionally, field addable
sub-fed breakers (up to 250 amps) or feed through lug kits can
be field installed without utilizing any of your feeder breaker
positions or increasing your box height. Furthermore, the unique
design allows the panel to be inverted in the field and keep its
labeling legible.
1) Completely symmetrical boxes may be mounted with
either end up. There are two pre-punched equipment ground
connector locations for contractor friendly installation.
be performed easily. MLO kits and Main Breaker Kits are
interchangeable and can be changed/added in the field without
making changes to the enclosure or interior.
2) Box comes pre-punched for optional, field installable doorin-door or hinged style trims. There are also two pre-punched
ground connector locations. The panel box will accept both
standard ground connector (EGK and ECGK) assemblies and
insulated ground connector kits (IGK and ICGK).
5) Branch neutral connections are near the breaker connections
to speed wiring and reduce clutter. The standard P1 neutral
is rated for 100% of the panel’s ampacity and will accept copper
or aluminum wire. Optional 200% and 2/0 neutrals are
also available.
3) Interior is completely symmetrical allowing it to be changed
from top to bottom feed by simply rotating the interior.
6) The panel includes space to add (1) sub-feed breaker (max
250 amps), feed-thru lugs or TPS3 (SPD) kit.
4) Choose either a Main Breaker kit or Main Lug kit with which
to terminate your incoming cables. Main lug kits are contractor
friendly lugs through 350 kcmil (250 amp panel) or (1) 600
kcmil or (2) 250 kcmil connectors for 400 amp panels. No line
connectors in the P1 panel require multiple wires under one
screw. Main Breaker kits (250 amps and below) are horizontally
mounted allowing field convertible top or bottom feeds to
7) Siemens standard trim has hidden hinges and mounting
hardware for added safety. The rounded door corners not only
enhance the panel’s appearance but also help to eliminate
injuries caused from sharp corners.
3
8) Semi-flush lock comes standard. Easily identified locked position
denoted by keyway being horizontal when door has been locked.
4
2
5
7
1
6
14
P1 Panelboards • Quick reference for selection and application
8
Catalog Numbering System
Unassembled Panelboards
Type P1 unassembled panelboards are
completely convertible from main lug
to main breaker and vice-versa.
Additionally feed-thru lugs, or subfeed
circuit breakers up to 400 ampere can
be added without increasing the box
height for Revised P1 with “T” suffix,
see the chart.
Note: Main/Subfeed Breaker mounting
kits may be ordered with or without
breakers included, see page 5
and 6 for selection.
4. List required branch circuit
breakers and filler plates to cover
any unused positions.
5. Select any modifications
or accessories.
1. Compute total number of poles to
determine interior catalog number.
(Note: BL / BQD (or) xGB Main Breaker
will use unit space. The total number of
poles should include 2 (or) 3 poles for
1-phase (or) 3-phase mains.)
2. List catalog number and price of
interior, box and front.
3. Select main lug kit or main breaker
kit from appropriate tables.
Note: Revised P1 was introduced in June 2014. All original P1 devices do not include the "Subfeed Space" Indicator.
All original P1 included the Subfeed Space as standard.
P 1 X 1 8 MC 2 5 0 A T
Type of Panel
P1
Voltage and System
X = 208Y/120, 3-Phase 4-Wire
A = 120/240V, 1-Phase 3-Wire
E = 480Y/277V, 3-Phase 4-Wire
7 = xGB interior, 480Y/277V, 3-Phase 4-Wire
Circuits
18, 30, 42, 54* (*Revised P1 only)
Mains MC = Convertible mains
Select Main Lug Kit or Breaker Mounting Kit from page ?
Amperage
400A max (typically 250A or 400A)
Main Bus Material
A = Aluminum
C = Copper
Subfeed Space Indicator (for Revised P1 only)
T = Subfeed Space Included
Note: Standard bussing in P1 panels is tin plated for aluminum and copper.
Standard bus is temperature rated to the maximum amperage in the panel.
Branch Breakers
Panel Type
P1, Revised P11
Voltage (Max.)
240
480 / 277
600 / 347 3
Breaker Type
BL, BLH, HBL, BQD, NGB, HGB, LGB
BQD, NGB, HGB, LGB,
BQDG 2, NGB, HGB, LGB
Additional Information
See Page 17
1 Consult sales office for availability of CSA.
2 See Speedfax for additional information.
3 600/347V options are not available in a UPB panel - see factory assembled section.
P1 Panelboards • Quick reference for selection and application
15
Distributor Stock
Type P1 Panelboards
Pricing An Unassembled Panel
400A Max. — 20" Wide x 5.75" Deep
1. Choose the appropriate Interior from the
table below.
2. Choose the Main Device: Main Lugs from page
16, Main Breaker Kit from pages 16 - 17 and
Main Breakers from Section 7.
3. Choose Branch Breakers. BL, BQD and xGB
breakers from Section 7.
4. Choose Feed-Thru Lugs or Subfeed Breaker
Kit from pages 16 - 17 and Subfeed
Breaker from Section 7.
Type P1 Unassembled Panelboards (Revised P1 introduced 2014)
Amps
Max. # of
Poles
Original Interior
Catalog Number
Box Size
Type 1
Encl.
Type 3R/12
Encl.
Type 1 Front
Surface
Type1 Front
Flush
P1A18MC250AT
P1A30MC250AT
P1A42MC250AT
P1A54MC250AT
—
P1A30MC400AT
P1A42MC400AT
P1A54MC400AT
P1A18MC250CT
P1A30MC250CT
P1A42MC250CT
P1A54MC250CT
—
P1A30MC400CT
P1A42MC400CT
P1A54MC400CT
32
38
44
50
—
62
68
74
32
38
44
50
—
62
68
74
B32
B38
B44
B50
—
B62
B68
B74
B32
B38
B44
B50
—
B62
B68
B74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
P1X18MC250AT
P1X30MC250AT
P1X42MC250AT
P1X54MC250AT
—
P1X30MC400AT
P1X42MC400AT
P1X54MC400AT
P1X18MC250CT
P1X30MC250CT
P1X42MC250CT
P1X54MC250CT
—
P1X30MC400CT
P1X42MC400CT
P1X54MC400CT
32
38
44
50
—
62
68
74
32
38
44
50
—
62
68
74
B32
B38
B44
B50
—
B62
B68
B74
B32
B38
B44
B50
—
B62
B68
B74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
P1E18MC250AT
P1E30MC250AT
P1E42MC250AT
P1E54MC250AT
—
P1E30MC400AT
P1E42MC400AT
P1E54MC400AT
P1E18MC250CT
P1E30MC250CT
P1E42MC250CT
P1E54MC250CT
—
P1E30MC400CT
P1E42MC400CT
P1E54MC400CT
32
38
44
50
—
62
68
74
32
38
44
50
—
62
68
74
B32
B38
B44
B50
—
B62
B68
B74
B32
B38
B44
B50
—
B62
B68
B74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
P1718MC250AT
P1730MC250AT
P1742MC250AT
P1754MC250AT
—
P1730MC400AT
P1742MC400AT
P1754MC400AT
P1718MC250CT
P1730MC250CT
P1742MC250CT
P1754MC250CT
—
P1730MC400CT
P1742MC400CT
P1754MC400CT
32
38
44
50
—
62
68
74
32
38
44
50
—
62
68
74
B32
B38
B44
B50
—
B62
B68
B74
B32
B38
B44
B50
—
B62
B68
B74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
WP32
WP38
WP44
WP50
—
WP62
WP68
WP74
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
S32B
S38B
S44B
S50B
—
S62B
S68B
S74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
F32B
F38B
F44B
F50B
—
F62B
F68B
F74B
Revised P1 Interior
Catalog Number
Convertible Mains — 1-Phase, 3-Wire 120/240V
250
400
250
400
18
30
42
54
18
30
42
54
18
30
42
54
18
30
42
54
P1A18MC250A
P1A30MC250A
P1A42MC250A
18
30
42
54
18
30
42
54
18
30
42
54
18
30
42
54
P1X18MC250A
P1X30MC250A
P1X42MC250A
18
30
42
54
18
30
42
54
18
30
42
54
18
30
42
54
P1E18MC250A
P1E30MC250A
P1E42MC250A
18
30
42
54
18
30
42
54
18
30
42
54
18
30
42
54
P1718MC250A
P1730MC250A
P1742MC250A
P1A18MC400A
P1A30MC400A
P1A42MC400A
P1A18MC250C
P1A30MC250C
P1A42MC250C
P1A18MC400C
P1A30MC400C
P1A42MC400C
Convertible Mains — 3-Phase, 4-Wire 208Y/120V
250
400
250
400
P1X18MC400A
P1X30MC400A
P1X42MC400A
P1X18MC250C
P1X30MC250C
P1X42MC250C
P1X18MC400C
P1X30MC400C
P1X42MC400C
Convertible Mains — 3-Phase, 4-Wire 480Y/277V
250
400
250
400
P1E18MC400A
P1E30MC400A
P1E42MC400A
P1E18MC250C
P1E30MC250C
P1E42MC250C
P1E18MC400C
P1E30MC400C
P1E42MC400C
Interiors for xGB Breakers — 3-Phase, 4-Wire 480Y/277V
250
400
250
400
P1718MC400A
P1730MC400A
P1742MC400A
P1718MC250C
P1730MC250C
P1742MC250C
P1718MC400C
P1730MC400C
P1742MC400C
42 circuit with Back-fed Main
54 circuit 400A
a
16
Front included in NEMA 3R and 3R/12 Box.
P1 Panelboards • Quick reference for selection and application
Product Category UPB
Distributor Stock
Type P1 Panelboards
Lug Kits — Main or Feed Thru
Amp
Wire Range
Rating Matl. (includes Neutral)
AL
250
CU
AL
400
CU
400
AL
Service
1 Phase
3 Phase
1 Phase
(1) #6 AWG350 kcmil (CU or AL)
3 Phase
1 Phase
(2) 1/0 - 250 kcmil
or (1) #2 AWG-600 kcmil 3 Phase
1 Phase
(2) 1/0 - 4/0
or (1) 1/0 - 600 kcmil
3 Phase
1 Phase
AL 1/0-750 kcmil
(max. 600 kcmil CU wire) 3 Phase
(1) #6 AWG350 kcmil (CU or AL)
Original
Catalog
Number
MLKA1
MLKA3
MLKC1
MLKC3
4MLKA1
4MLKA3
4MLKC1
4MLKC3
–
–
Revised P1
Catalog
Number
MLKA1A
MLKA3A
MLKC1A
MLKC3A
4MLKA1A
4MLKA3A
4MLKC1A
4MLKC3A
4MLKA1B
4MLKA3B
MBKFD3A
Breaker Mounting Kits — Main or Subfeed Strap Kit w/o Breaker
Ampere
Rating
100A
Breaker Types
BQD
100A
BL, BLH, HBL
125A
NGB, HGB, LGB
125A
ED4, ED6, HED4, HED6
225A
QJ2, QJH2, QJ2-H
250A
FXD6, FD6, HFD6, HFXD6
400A
JXD2, JD6, JXD6,
HJD6, HJXD6
a
a 400
Service
3-Phase
1-Phase
3-Phase
1-Phase
3-Phase
1-Phase
3-Phase
1-Phase
3-Phase
1-Phase
3-Phase
1-Phase
3-Phase
Original P1
Catalog
Number
MBKBC3
MBKBL1
MBKBL3
MBKNB1
MBKNB3
MBKED1
MBKED3
MBKQJ1
MBKQJ3
MBKFD1
MBKFD3
MBKJD1
MBKJD3
amp kit is for main only — not allowed for subfeed breaker.
main occupies branch space.
Revised P1
Catalog
Number
Use Back-fed
Main Label
Kit # MBKBFAb
(includes Neutral
Lug, "MAIN" label
and instructions)
MBKQJ3A
MBKED1A
MBKED3A
MBKQJ1A
MBKQJ3A
MBKFD1A
MBKFD3A
MBKJD1A
MBKJD3A
 Back-fed
Copper Neutral Lug Kits — 250A
Number
of Circuits Description
18
30
42
54, 66
2 or 4 Branch Neutral Strips,
1 Main Neutral Lug, Hardware
2/0 Neutral Lug Kits — 250A and 400A
18
30
42
54, 66
2 or 4 Branch Neutral Strips,
1 Main Neutral Lug, Hardware
200% Neutral Lug Kits/250A
18
30
42
54, 66
2 or 4 Branch Neutral Strips,
1 Main Neutral Lug, Hardware
200% Neutral Lug Kits/400A
18
30
42
54, 66

2 or 4 Branch Neutral Strips, 1 Main
600MCM Neutral Lug, Hardware
Replacement Parts Only
Miscellaneous Parts and Accessories
Original P1
Catalog
Number
Revised P1
Catalog
Number
—
—
—
—
Use 30 ckt kit
LNLK30A
LNLK42A
LNLK54A
CNKL18
CNKL30
CNKL42
—
Use 30 ckt kit
CNLK30A
CNLK42A
CNLK54A
Catalog #
BK1
BK1A
BK2
BK3
IMK1
11-1824-01
12-1110-01
11-1056-01
NBK03
NBK04
NBK05
2NLK18
2NLK30
2NLK42
—
Use 30 ckt kit
2NLK30A
2NLK42A
2NLK54A
42NLK18
42NLK30
42NLK42
—
Use 30 ckt kit
42NLK30A
42NLK42A
42NLK54A
NBK06
EGK
ECGK
IGK
ICGK
EWK1
EWK2
EBF1
P1SCRWS
DFFP1
P1CONBPHCU 
P1CONBPHAL 
P1CONACPHCU 
P1CONACPHAL 
Description
Bonding Kit for 250A max. Original P1 Panels
Bonding Kit for 250A max. Revised P1 Panels
Bonding kit for S1/S2 400 & 600
Bonding kit
Interior Adjusting Kit
Directory Card Holder
Directory Card
NEMA Instruction Book
Number Strips 1–42 . Stick-on type;
Use w/ P1 series Panels
Number Strips 43–84. Stick-on type;
Use w/ P1 series Panels
Number Strips 85–126. Stick-on type;
Use w/ P1 series Panels
Number Strips 127–168. Stick-on type;
Use w/ P1 series Panels
AL Ground Bus 44 Connections
CU Ground Bus 44 Connections
Insulated AL Ground Bus
Insulated CU Ground Bus
End Wall Kit with Knockouts (20" W x 5.75" DP)
End Wall Kit with Knockouts (24" W x 7.75" DP)
NEB/HEB Filler Plate
Package of 42 breaker mounting screws for P1
1" Branch circuit filler plate (suitable for replacing
QF3 in P1 thru P5 Panelboards and Switchboards)
Connector kit – 6 pcs. B-phase Copper
Connector kit – 6 pcs. B-phase Aluminum
Connector kit – 6 pcs. A or C-phase Copper
Connector kit – 6 pcs. A or C-phase Aluminum
Product Category UPB
P1 Panelboards • Quick reference for selection and application
17
Warehouse Stock/Unassembled
Main Breaker Mounting Kits with Breakers for P1 Panels
(250A and lower can be used as subfeed kits also)
Original P1
Catalog Number
MBKED3100
MBKED3125
MBKQJ1125
MBKQJ1150
MBKQJ1175
MBKQJ1200
MBKQJ1225
MBKQJ3125
MBKQJ3150
MBKQJ3175
MBKQJ3200
MBKQJ3225
MBKQJ1125H
MBKQJ1150H
MBKQJ1175H
MBKQJ1200H
MBKQJ1225H
MBKQJ3125H
MBKQJ3150H
MBKQJ3175H
MBKQJ3200H
MBKQJ3225H
MBKFD3150
MBKFD3175
MBKFD3200
MBKFD3225
MBKFD3250
MBKJD1300
MBKJD3300
MBKJD1400
MBKJD3400
MBKJD12300
MBKJD32300
MBKJD12400
MBKJD32400
a Kits
Revised P1
Catalog Number
Ratings
Description
MBKED3100A
MBKED3125A
MBKQJ1125A
MBKQJ1150A
MBKQJ1175A
MBKQJ1200A
MBKQJ1225A
MBKQJ3125A
MBKQJ3150A
MBKQJ3175A
MBKQJ3200A
MBKQJ3225A
MBKQJ1125HA
MBKQJ1150HA
MBKQJ1175HA
MBKQJ1200HA
MBKQJ1225HA
MBKQJ3125HA
MBKQJ3150HA
MBKQJ3175HA
MBKQJ3200HA
MBKQJ3225HA
MBKFD3150A
MBKFD3175A
MBKFD3200A
MBKFD3225A
MBKFD3250A
MBKJD1300A
MBKJD3300A
MBKJD1400A
MBKJD3400A
MBKJD12300A
MBKJD32300A
MBKJD12400A
MBKJD32400A
240V
Kit w/3-pole ED4 100A breaker
Kit w/3-pole ED4 125A breaker
Kit w/2-pole QJ2 125A breaker
Kit w/2-pole QJ2 150A breaker
Kit w/2-pole QJ2 175A breaker
Kit w/2-pole QJ2 200A breaker
Kit w/2-pole QJ2 225A breaker
Kit w/3-pole QJ2 125A breaker
Kit w/3-pole QJ2 150A breaker
Kit w/3-pole QJ2 175A breaker
Kit w/3-pole QJ2 200A breaker
Kit w/3-pole QJ2 225A breaker
Kit w/2-pole QJ2H 125A breaker
Kit w/2-pole QJ2H 150A breaker
Kit w/2-pole QJ2H 175A breaker
Kit w/2-pole QJ2H 200A breaker
Kit w/2-pole QJ2H 225A breaker
Kit w/3-pole QJ2H 125A breaker
Kit w/3-pole QJ2H 150A breaker
Kit w/3-pole QJ2H 175A breaker
Kit w/3-pole QJ2H 200A breaker
Kit w/3-pole QJ2H 225A breaker
Kit w/3-pole FXD6 150A breaker
Kit w/3-pole FXD6 175A breaker
Kit w/3-pole FXD6 200A breaker
Kit w/3-pole FXD6 225A breaker
Kit w/3-pole FXD6 250A breaker
Kit w/2-pole JXD6 300A breaker
Kit w/3-pole JXD6 300A breaker
Kit w/2-pole JXD6 400A breaker
Kit w/3-pole JXD6 400A breaker
Kit w/2-pole JXD2 300A breaker
Kit w/3-pole JXD2 300A breaker
Kit w/2-pole JXD2 400A breaker
Kit w/3-pole JXD2 400A breaker
65KA
65KA
10KA
10KA
10KA
10KA
10KA
10KA
10KA
10KA
10KA
10KA
42KA
42KA
42KA
42KA
42KA
42KA
42KA
42KA
42KA
42KA
65KA
65KA
65KA
65KA
65KA
65KA
65KA
65KA
65KA
65KA
65KA
65KA
65KA
480V
18KA
18KA
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
35KA
35KA
35KA
35KA
35KA
35KA
35KA
35KA
35KA
–
–
–
–
Branch Breakers Selection
for P1
Selection Guide
1. Select breaker type.
2. Select required amperage.
3. Select number of poles.
4. Select branch breaker catalog
numbers.
5. Select ground bar and filler
plates. (See replacement parts
& accessories on Page 15.)
300A Main installed.
These Revised P1 kits can now
be used as top or
bottom feed.
are for Main only. New “Revised P1” kits can be used for either top feed or bottom feed.
NOTE: "Revised P1" Kits above only work for interior numbers ending in "T" or "N". Use "Original P1" kits for all others.
AFCI – Combination Type Arc Fault Circuit Interrupter
Interrupting Ratings (kA)
RMS Symmetrical Amperes
BAF
2-pole
Ampere
Rating
15
20
15
20
15
20
15
20
Catalog
Number
B115AFC
B120AFC
B115AFCH
B120AFCH
BA115AFCHH
BA120AFCHH
B215AFC
B220AFC
Volts AC
120
10
10
22
22
65
65
10
10
BAFH
2-pole
15
20
B215AFCH
B220AFCH
22
22
Breaker
Type
BAF2
1-pole
BAFH2
1-pole
HBAF2
1-pole
Switching Neutrals
Breaker
Type
BG
2-Wire
Common Trip
BG
3-Wire
Common Trip
* Built to order.
Ampere
Rating
15
20
30
15
20
30
Catalog
Number
BG215*
BG220*
BG230*
BG315*
BG320*
BG330*
120/240
—
—
—
—
—
—
—
240
—
—
—
—
—
—
—
—
—
—
—
—
—
Maximum Interrupting Rating (kA)
120V AC 120/240V AC
240V AC
10
—
—
10
—
—
10
—
—
—
10
—
—
10
—
—
10
—
AFCI – Branch Feeder Type Arc Fault Circuit Interrupter
Interrupting Ratings (kA)
RMS Symmetrical Amperes
Breaker
Type
BAF2
1-pole
BAF2H
1-pole
HBAF2
1-pole
Catalog
Number
BA115AF
BA120AF
BA115AFH
BA120AFH
BA115AFHH
BA120AFHH
Volts AC
120
10
10
22
22
65
65
120/240
—
—
—
—
—
—
240
—
—
—
—
—
—
Dual Function AFCI/GFCI Circuit Breaker
Interrupting Ratings (kA)
RMS Symmetrical Amperes
Breaker
Type
BFGA2
1-pole
BFGAH2
1-pole
HBFGA2
1-pole
.
Product Category UPB
18
Ampere
Rating
15
20
15
20
15
20
P1 Panelboards • Quick reference for selection and application
Ampere
Rating
15
20
15
20
15
20
Catalog
Number
BA115DF
BA120DF
BA115DFH
BA120DFH
BA115DFHH
BA120DFHH
Volts AC
120
10
10
22
22
65
65
120/240
—
—
—
—
—
—
240
—
—
—
—
—
—
Warehouse Stock / Unassembled
Type P1 Panelboards
Branch Breakers Selection for P1
Selection Guide
1. Select breaker type.
2. Select required amperage.
3. Select number of poles.
4. S
elect branch breaker catalog numbers.
BL Branch Breakers – 10,000A IR
Amp
Rating
15
20
25
30
35
40
45
50
55
60
70
80
90
100
1-Pole
120/240V
B115
B120
B125
B130
B135
B140
B145
B150
B155
B160
B170
—
—
—
2-Pole
120/240V
B215
B220
B225
B230
B235
B240
B245
B250
—
B260
B270
B280
B290
B2100
2-Pole
240V
B215R
B220R
B225R
B230R
B235R
B240R
B245R
B250R
—
—
—
—
—
—
HBL Branch Breakers – 65,000A IR
Amp
Rating
15
20
30
40
50
60
70
80
90
100
1-Pole
120/240V
B115HH
B120HH
B130HH
B140HH
B150HH
—
—
—
—
—
2-Pole
120/240V
B215HH
B220HH
B230HH
B240HH
B250HH
B260HH
B270HH
B280HH
B290HH
B2100HH
3-Pole
240V
B315
B320
B325
B330
B335
B340
B345
B350
—
B360
B370
B380
B390
B3100
3-Pole
240V
B315HH
B320HH
B330HH
B340HH
B350HH
B360HH
B370HH
B380HH
B390HH
B3100HH
GFCI Personnel Protection (5MA)
Interrupting Ratings (kA)
RMS Symmetrical Amperes
Breaker
Type
BLF
1-Pole
BLF
2-Pole
BLHF
1-Pole
BLHF
2-Pole
Ampere
Rating
15
20
25
30
15
20
30
40
50
60
15
20
30
15
20
30
40
50
60
Catalog
Number
BF115
BF120
BF125
BF130
BF215
BF220
BF230
BF240
BF250
BF260
BF115H
BF120H
BF130H
BF215H
BF220H
BF230H
BF240H
BF250H
BF260H
Volts AC
120
10
10
10
10
—
—
—
—
—
—
22
22
22
—
—
—
—
—
—
120/240
—
—
—
—
10
10
10
10
10
10
—
—
—
22
22
22
22
22
22
240
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5. Select ground bar and filler plates.
(See replacement parts & accessories
on Pages 17 and 18.)
BLH Branch Breakers – 22,000A IR
Amp
Rating
15
20
25
30
40
50
55
60
70
80
90
100
1-Pole
120/240V
B115H
B120H
B125H
B130H
B140H
B150H
B155H
B160H
B170H
—
—
—
2-Pole
120/240V
B215H
B220H
B225H
B230H
B240H
B250H
—
B260H
B270H
B280H
B290H
B2100H
3-Pole
240V
B315H
B320H
B325H
B330H
B340H
B350H
—
B360H
B370H
B380H
B390H
B3100H
BQD Branch Breakers – 14,000A IR Max. @ 480/277 Vac /
65,000A IR max. @ 240 Vacc
Amp
Rating
15
20
25
30
35
40
45
50
60
70
80
90
100
1-Pole
277V
BQD115
BQD120
BQD125
BQD130
BQD135
BQD140
BQD145
BQD150
BQD160
BQD170
BQD180
BQD190
BQD1100
2-Pole
480Y/277V
BQD215
BQD220
BQD225
BQD230
BQD235
BQD240
BQD245
BQD250
BQD260
BQD270
BQD280
BQD290
BQD2100
3-Pole
480Y/277V
BQD315
BQD320
BQD325
BQD330
BQD335
BQD340
BQD345
BQD350
BQD360
BQD370
BQD380
BQD390
BQD3100
GB Family Branch Breakers
NGB –
25,000 A IR Max. @ 480/277V AC / 100,000 A IR @ 240V AC
HGB – 35,000 A IR Max. @ 480/277V AC / 100,000 A IR @ 240V AC
LGB – 65,000 A IR Max. @ 480/277V AC / 100,000 A IR @ 240V AC
Amp
Rating
15
20
25
30
35
40
45
50
60
70
80
90
100
110
125
1-pole
277V
xGB1B015B
xGB1B020B
xGB1B025B
xGB1B030B
xGB1B035B
xGB1B040B
xGB1B045B
xGB1B050B
xGB1B060B
xGB1B070B
xGB1B080B
xGB1B090B
xGB1B100B
xGB1B110B
xGB1B125B
2-pole
480Y/277V
xGB2B015B
xGB2B020B
xGB2B025B
xGB2B030B
xGB2B035B
xGB2B040B
xGB2B045B
xGB2B050B
xGB2B060B
xGB2B070B
xGB2B080B
xGB2B090B
xGB2B100B
xGB2B110B
xGB2B125B
3-pole
480Y/277V
xGB3B015B
xGB3B020B
xGB3B025B
xGB3B030B
xGB3B035B
xGB3B040B
xGB3B045B
xGB3B050B
xGB3B060B
xGB3B070B
xGB3B080B
xGB3B090B
xGB3B100B
xGB3B110B
xGB3B125B
Replace x with N, H or L depending on desired type of breaker
NOTE: 2-pole and 3-pole xGB Frame Breakers are also rated at
14,000 A IR max. for 600Y/347V AC systems. UPB interiors
are only rated to 480V max. - see factory assembled section
for proper interiors.
n Built to order. Allow 2–3 weeks for delivery.
a HACR rated.
 To
 To
add shunt trip to BL breakers, see Speedfax for Breaker Accessories.
add shunt trip to BQD breakers, see Speedfax for Breaker Accessories.
P1 Panelboards • Quick reference for selection and application
19
TPS3 02
Surge Protection Device (SPD) for Revised P1 Lighting Panelboards
(for Original P1 – refer to TPS3 01 Series)
These newly developed kits are for use in the new revised P1 Series only.
Interior part numbers must end with “N” or “T”.
Features:
• Mounts internal to:
– Revised P1 Lighting Panelboards
• Consult factory for field retrofit in Revised P1
Lighting Panelboards
• UL 1449 3rd Edition Recognized
• UL 1283
• Type 4 SPD intended for use in Type 1 applications (Type 2, cUL)
• UL Type 1 tested with all internal OCP and safety coordination
features included
• Large block, individually fused, thermally protected, 50 kA MOVs
• 20 kA In (most models)
• 200 kA SCCR (most models)
• UL96A Lightning Protection Master Label appropriate (@ 20 kA In)
•Applications
– Provides main service or downstream protection for sensitive
computer and electronic loads
– Standard redundancy use: 100 kA per phase
– Increased redundancy use: 200 kA per phase
– Maximum redundancy use: 300 kA per phase
• SPD Specification
– Surge Current Rating Per Phase
Per Phase
L-N
L-G
N-G
100kA 50kA50kA50kA
150kA
100kA 50kA 50kA
200kA
100kA100kA100kA
250kA
150kA100kA100kA
300kA
150kA150kA150kA
–
–
–
–
–
–
–
100% monitoring (Every MOV is monitored, incl. N-G)
EMI/RFI filtering: Active tracking up to -50 db from 10 kHz to 100 MHz
Repetitive impulse: 5,000 hits
Less than ½ nanosecond response time
Relative humidity range: 1-95% non-condensing
Operating frequency: 47-63 Hz
Operating temperature: -25°C (-15°F) to +60°C (140°F)
UL 1449 3rd Edition SPD
20
P1 Panelboards • Quick reference for selection and application
-■ Direct■bus■connected
-■ UL■1449■3rd■Edition■effective■■
-■ UL■1449■3rd■Edition■Recognized ■■ Stand
C62.45-2002
-■ Can■be■wired■to■a■circuit■breaker■(consult■
September■2009
-■ UL■1283
-■ LED■in
■
1992/2000■NEMA■LS-1
factory■at■time■of■order■or■see■installation■
-■ Designed,■manufactured■&■tested■
-■ Audible■alarm■with■silence■switch■■-■ Audib
-■ NEC■Article■285
manual■for■retrofit)
consistent■with:
and■test■button
button
-■ IEC■61643,■CE
■
10■year■warranty■
-■ ANSI/IEEE■C62.41.1-2002,■
-■ Dry■contacts
-■ Dry■co
-■ Large■block,■individually■fused,■■
C62.41.2-2002,■and■
-■ EMI/RFI■filtering
thermally■protected,■50■kA■MOVs
■■ Standard■Monitoring
C62.45-2002
-■ Protection■modes■on■L-N,■L-G,■L-L,■N-G
■■ Availa
■■ SPD■Features
■■ SPD■Features
■■ Key■Bid■Specifications
-■ LED■indicators
-■ 1992/2000■NEMA■LS-1
-■ In■Rating■-■20■kA
-■ Surge
■
Direct■bus■connected
-■ UL■1449■3rd■Edition■effective■■
-■ UL■1449■3rd■Edition■Recognized
-■ Audible■alarm■with■silence■switch■and■test■
-■ NEC■Article■285
-■ Short■Circuit■Current■Rating■-■200■kA
■
Can■be■wired■to■a■circuit■breaker■(consult■
• SPD Features
•
SPD
Features
•
Key
Bid
Specifications
September■2009
■
UL■1283
button
-■ IEC■61643,■CE
-■ Surge■Current■Rating
-Ordering■Information
UL 1449 3rd Edition Recognized
– UL 1449 3rd Edition effective
–-■Direct
bus connected
factory■at■time■of■order■or■see■installation■
-■ Designed,■manufactured■&■tested■
■ –
Audible■alarm■with■silence■switch■■
Dry■contacts
-■ Large■block,■individually■fused,■■
Per■Phase■■=■■■L-N■■■+■■■L-G
– Can be wired to a circuit breaker
–
UL 1283
September 2009
consistent■with:
and■test■button
thermally■protected,■50■kA■MOVs manual■for■retrofit)
(consult factory at time of order or see
Catalog■#■■
Audible100■kA■■■■■■■■■■■■50■kA■■■■50■kA
alarm with silence switch
■
-■ 10■year■warranty■
-■ –
Dry■contacts
■■ Available■Options
-■ – ANSI/IEEE■C62.41.1-2002,■
Designed, manufactured & tested
installation manual for retrofit)
and test button
C62.41.2-2002,■and■
■
EMI/RFI■filtering
consistent with:
–-■10Surge■counter
year warranty
– Dry contacts
■■ Standard■Monitoring
Protection■modes■on■L-N,■L-G,■L-L,■N-G
C62.45-2002
– ANSI/IEEE C62.41.1-2002,
Voltage■Code
-■ –
EMI/RFI filtering
C62.41.2-2002, and C62.45-2002 -■ LED■indicators
• Standard Monitoring
-■ Ordering■Information
1992/2000■NEMA■LS-1
In■Rating■-■20■kA
-■ –
Protection
on L-N, L-G, L-L, N-G
A modes
= 120/240V,■1Ø,■3W■(Fig■1)■
– 1992/2000 NEMA LS-1
– LED indicators
-■ Audible■alarm■with■silence■switch■and■test■
- 20
-■ –I
-■ NEC■Article■285
Short■Circuit■Current■Rating■-■200■kA
n Rating B
= kA
120/240V,■3Ø,■4W■(Fig■3)
– NEC Article 285
– Audible alarm with silence switch
button
-■ –
Short Circuit
Rating - 200 kA
C = Current
120/208V,■3Ø,■4W■(Fig■2)■
-■ IEC■61643,■CE
Surge■Current■Rating
■ test button
■
■
and
Catalog■#■■
– IEC 61643, CE
–
Surge Current
Rating
-■ Dry■contacts
D = 240V,■3Ø,■3W■(Fig■4)■
-■ Large■block,■individually■fused,■■
Per■Phase■■=■■■L-N■■■+■■■L-G
– Dry contacts
Per Phase
L-N + L-G
E = =
277/480V,■3Ø,■4W■(Fig■2)
thermally■protected,■50■kA■MOVs
100■kA■■■■■■■■■■■■50■kA■■■■50■kA
– Large block, individually fused,
100kA
50kA
50 kA
F = 480V,■3Ø,■3W■(Fig■4)
Voltage■Code
Surge■Current■(kA)
Options
■■ Available■Options
thermally protected,
50 kA MOVs
• Available Options
G
=
Œ
600V,■3Ø,■3W■(Fig■4)
A = 120/240V,■1Ø,■3W■(Fig■1)■
10 = 100■kA■per■phase
X = Surge■counter
-■ Surge■counter
– Surge counter
TPS3 02
TPS3 o
TPS3 o 02
oo
o
K = 380/220V,■3Ø,■4W■(Fig■2)
B = 120/240V,■3Ø,■4W■(Fig■3)
15 = 150■kA■per■phase
L = 600/347V,■3Ø,■4W■(Fig■2)
C = 120/208V,■3Ø,■4W■(Fig■2)■
20 = 200■kA■per■phase
Ordering■Information
A
S = 400/230V,■3Ø,■4W■(Fig■2)
D = 240V,■3Ø,■3W■(Fig■4)■
25 = 250■kA■per■phase
E = 277/480V,■3Ø,■4W■(Fig■2)
30 = 300■kA■per■phase
Catalog■#■■
■
■
F = 480V,■3Ø,■3W■(Fig■4) ■
-■ Example:■■TPS3C0220X■=■SPD■for■a■208/120V■panelboard■with■a■surge■current■capacity■of■200■
G = 600V,■3Ø,■3W■(Fig■4)Œ
kA■per■phase■and■a■surge■counter■option
K = 380/220V,■3Ø,■4W■(Fig■2)
Voltage■Code
Surge■Current■(kA)
Options
-■ When■surge■counter■is■not■selected,■include■a■zero■(0)■in■the■field
L = 600/347V,■3Ø,■4W■(Fig■2)
A = 120/240V,■1Ø,■3W■(Fig■1)■
10
=
100■kA■per■phase
X
= Surge■counter
Available■Accessories:■Ordered■Separately
S = 400/230V,■3Ø,■4W■(Fig■2)
B = 120/240V,■3Ø,■4W■(Fig■3)
15 = -150■kA■per■phase
Voltage■Code
Service■Voltage
■ RMSIE■-■Remote■monitor
C = 120/208V,■3Ø,■4W■(Fig■2)■
20 = 200■kA■per■phase
A
120/240V,■1Ø,■3W■(Fig■1)
D = 240V,■3Ø,■3W■(Fig■4)■
25 = 250■kA■per■phase
B
120/240V,■3Ø,■4W■(Fig■3) 700
E = 277/480V,■3Ø,■4W■(Fig■2)
30 = 300■kA■per■phase
UL■1449■3rd■Edition■-■2009■Test■Data■Summary
C
120/208V,■3Ø,■4W■(Fig■2)
F = 480V,■3Ø,■3W■(Fig■4)
-■ Example:■■TPS3C0220X■=■SPD■for■a■208/120V■panelboard■with■a■surge■current■capacity■of■200■
G = 600V,■3Ø,■3W■(Fig■4)Œ
Voltage■Protection■Rating■■(VPR■-■6kV,■3kA)
D
240V,■3Ø,■3W■(Fig■4)
kA■per■phase■and■a■surge■counter■option
K = 380/220V,■3Ø,■4W■(Fig■2)
E
277/480V,■3Ø,■4W■(Fig■2)
1
Voltage■Code
Service■Voltage-■ When■surge■counter■is■not■selected,■include■a■zero■(0)■in■the■field
L-N
L-G
N-G
L-L
Type
In
SCCR
MCOV
L = 600/347V,■3Ø,■4W■(Fig■2)
F
480V,■3Ø,■3W■(Fig■4)
A
120/240V,■1Ø,■3W■(Fig■1)
700
700
700
1200
Type■4 20■kA 100■kA
150
Available■Accessories:■Ordered■Separately
S = 400/230V,■3Ø,■4W■(Fig■2)
TPS3 o 02
oo
o
G
600V,■3Ø,■3W■(Fig■4)
B
120/240V,■3Ø,■4W■(Fig■3)
700■■/■1200 700■/■1200
700
1800■/■1800 Type■4 20■kA 200■kA 150■/■320
-■ RMSIE■-■Remote■monitor
K
380/220V,■3Ø,■4W■(Fig■2)
1
C
120/208V,■3Ø,■4W■(Fig■2)
700
700
700
1200
Type■4 20■kA 200■kA
150
L
600/347V,■3Ø,■4W■(Fig■2)
1
D
240V,■3Ø,■3W■(Fig■4)
1200
1200
Type■4 10■kA 200■kA
320
S
400/230V,■3Ø,■4W■(Fig■2)
1
E
277/480V,■3Ø,■4W■(Fig■2) UL■1449■3rd■Edition■-■2009■Test■Data■Summary
1200
1200
1200
2000
Type■4 20■kA 200■kA
320
F
480V,■3Ø,■3W■(Fig■4)
1800
1800
Type■4 10■kA 200■kA
550
Voltage■Protection■Rating■■(VPR■-■6kV,■3kA)
G
600V,■3Ø,■3W■(Fig■4)
2500
2500
Type■4 10■kA 200■kA
690
Voltage■Code
Service■Voltage
L-N
L-G
N-G
L-L
Type
In
SCCR
MCOV
K
380/220V,■3Ø,■4W■(Fig■2)
1200
1200
1200
2000
Type■4
20■kA 200■kA
320
A
120/240V,■1Ø,■3W■(Fig■1)
700
700
700
1200
Type■4 20■kA 100■kA
150
L
600/347V,■3Ø,■4W■(Fig■2)
1500
1500
1500
2500
Type■4 10■kA
200■kA
420
Phase
Phase A (BLK)
Hot
(BLK)
B
120/240V,■3Ø,■4W■(Fig■3) 700■■/■1200 700■/■1200
700
1800■/■1800 }Type■4
20■kA 200■kAA 150■/■320
V
P
B Phase B (BLK)320
S
400/230V,■3Ø,■4W■(Fig■2)
1200
1200
1200
2000
Type■4 20■kA 200■kA
C
120/208V,■3Ø,■4W■(Fig■2)
700
700
700
1200
20■kA 200■kA
150
}Type■4
Neutral (WHT)
V Neutral (WHT)
N
Hot (BLK) 10■kA
D
240V,■3Ø,■3W■(Fig■4)
1200
1200
Type■4
200■kA
320
V
Phase C (BLK)
E
277/480V,■3Ø,■4W■(Fig■2)
1200
1200
1200
2000
Type■4
20■kA 200■kA C 320
Ground (GRN)
Ground (GRN)
F
480V,■3Ø,■3W■(Fig■4)
1800
1800
Type■4 10■kA 200■kA
550
Siemens■Industry,■Inc.
G
600V,■3Ø,■3W■(Fig■4)
2500
Type■4 10■kA 200■kA
690
Phase A (BLK)2500
Phase A (BLK)
Phase
A (BLK)
V
}V Hot (BLK)
Figure■2
Figu
Figure■1
Phase B (ORNG)
5400■Triangle■Parkway
B Phase B (BLK)
A
K
380/220V,■3Ø,■4W■(Fig■2)
1200
1200
1200
2000
Type■4
20■kA
200■kA
320
V
Phase B (BLK)
}V Neutral (WHT)
Norcross,■GA■30092
Neutral (WHT)
}
N
Split
L
600/347V,■3Ø,■4W■(Fig■2)
1500
1500
1500
2500
Type■4 10■kA 200■kAWye 420
Hi-Le
Phase
C (BLK)
Hot (BLK)
Phase C (BLK)
V
2■Hots,■1■Neu,■1■Grnd
3■Hot
Neutral
(WHT)
S
400/230V,■3Ø,■4W■(Fig■2)
1200
1200
2000
Type■4888-333-3545
20■kA 200■kA3■Hots,■1■Neu,■1■Grnd
320
Phase C (BLK) 1200
Ground (GRN)
Ground (GRN)
Ground (GRN)
1■Neu
C
Ground (GRN)
}
}
}
Figure■2
Figure■1
}V
}V
Figure■4
Wye
Split
Phase A (BLK) Hi-Leg■Delta■(B■High)
Phase A (BLK)
3■Hots,■1■Neu,■1■Grnd
2■Hots,■1■Neu,■1■Grnd
3■Hots,■(B■High),■■
Phase B (ORNG)
B (BLK)
B Phase
A
Neutral (WHT)
Neutral (WHT)
}V 1■Neu,■1■Grnd
N
Hot (BLK)
Hot (BLK)
Ground (GRN)
C
}
V
Phase C (BLK)
Ground (GRN)
Notes:
Split
2■Hots,■1■Neu,■1■Grnd
Delta■&■HRG■Wye
Phase A (BLK)
} 3■Hots,■1■Grnd
V
Phase C (BLK)
Figure■2
Figure■1
Œ Available■100■kA■&■150■kA■only
Wye
3■Hots,■1■Neu,■1■Grnd
Notes:
Œ
Figure■3
Available■100■kA■&■150■kA■only
Phase B (BLK)
Phase C (BLK)
Neutral (WHT)
Ground (GRN)
Ground (GRN)
Figure■3
Figure■4
Hi-Leg■Delta■(B■High)
3■Hots,■(B■High),■■
1■Neu,■1■Grnd
Delta■&■HRG■Wye
3■Hots,■1■Grnd
info.us@siemens.com
■
©2010■Siemens■Industry,■Inc.
All■Rights■Reserved.■Siemens■is■a■registered
Notes:
Siemens■Industry,■Inc.
trademark■of■Siemens■AG.■Product■names
Œ 5400■Triangle■Parkway
Available■100■kA■&■150■kA■only
mentioned■may■be■trademarks■or■registered
Norcross,■GA■30092
trademarks■of■their■respective■companies.
Specifications■are■subject■to■change■without
888-333-3545
notice.
info.us@siemens.com
■
©2010■Siemens■Industry,■Inc.
www.usa.siemens.com/spd
All■Rights■Reserved.■Siemens■is■a■registered
trademark■of■Siemens■AG.■Product■names
6.2.14.jb
mentioned■may■be■trademarks■or■registered
trademarks■of■their■respective■companies.
Specifications■are■subject■to■change■without
notice.
P1 Panelboards • Quick reference for selection and application
www.usa.siemens.com/spd
21
TPS3 L2 - True 10 Mode Protection
Surge Protection Device (SPD) for Revised P1 Lighting Distribution Panelboards
(for Original P1 – refer to TPS3 L1 Series)
These newly developed kits are for use in the new revised P1 Series only.
Interior part numbers must end with “N” or “T”.
Features:
• Mounts internal to:
– Revised P1 Lighting Panelboards
• Consult factory for field retrofit in Revised P1 Lighting Panelboards
• UL 1449 3rd Edition Recognized
• UL 1283
• Type 4 SPD intended for use in Type 1 applications (Type 2, cUL)
• UL Type 1 tested with all internal OCP and safety coordination
features included
• Large block, individually fused, thermally protected, 50 kA MOVs
• 20 kA In (most models)
• 200 kA SCCR (most models)
• UL96A Lightning Protection Master Label appropriate (@ 20 kA In
•Applications
– Provides main service or downstream protection for sensitive computer and
electronic loads
– Standard redundancy use: 150 kA per phase
– Maximum redundancy use: 300 kA per phase
• SPD Specifications
– Directly connected discrete protection elements between all possible modes
providing true 10 mode protection
– Surge Current Rating Per Phase
Per Phase
L-N
L-G
L-L
N-G
150kA 50kA50kA50kA50kA
300kA
100kA100kA100kA100kA
–
–
–
–
–
–
–
100% monitoring (Every MOV is monitored, incl. N-G)
EMI/RFI filtering: Active tracking up to -50 db from 10 kHz to 100 MHz
Repetitive impulse: 5,000 hits
Less than ½ nanosecond response time
Relative humidity range: 1-95% non-condensing
Operating frequency: 47-63 Hz
Operating temperature: -25°C (-15°F) to +60°C (140°F)
UL 1449 3rd Edition SPD
22
P1 Panelboards • Quick reference for selection and application
-■ Direct■bus■connected
-■ UL■1449■3rd■Edition■effective■■
-■ UL■1449■3rd■Edition■Recognized
-■ Can■be■wired■to■a■circuit■breaker■(consult■
September■2009
-■ UL■1283
factory■at■time■of■order■or■see■installation■
-■ Designed,■manufactured■&■tested■
-■ Audible■alarm■with■silence■switch■■
manual■for■retrofit)
consistent■with:
and■test■button
-■ 10■year■warranty■
-■ ANSI/IEEE■C62.41.1-2002,■
-■ Dry■contacts
C62.41.2-2002,■and■
-■ EMI/RFI■filtering
■
■
Standard■Monitoring
C62.45-2002
-■ Protection■modes■on■L-N,■L-G,■L-L,■N-G
■■ SPD■Features
■■ SPD■Features
■■ Key■Bid■Specifications
-■ LED■indicators
■ 1992/2000■NEMA■LS-1
-■ In-■■Rating■-■20■kA
-■ Direct■bus■connected
-■ -UL■1449■3rd■Edition■effective■■
UL■1449■3rd■Edition■Recognized■-■2009■
-■ Audible■alarm■with■silence■switch■and■test■
-September■2009
■ NEC■Article■285
-■ Can■be■wired■to■a■circuit■breaker■(consult■ -■ Short■Circuit■Current■Rating■-■200■kA
-■ Key
UL■1283
•
SPD
Features
•
SPD
Features
•
Bid Specifications
buttonfactory■at■time■of■order■or■see■installation■ -■ Surge■Current■Rating
■ IEC■61643,■CE
-■ -Designed,■manufactured■&■tested■
■
Audible■alarm■with■silence■switch■and■
–
UL
1449 3rd Edition Recognized - 2009
– UL 1449 3rd Edition effective
–
Direct
bus
connected
-■ Dry■contacts
-■ Large■block,■individually■fused,■■
Per■Phase■■=■■■L-N■■■+■■■L-G
consistent■with:
test■button
manual■for■retrofit)
– Can be wired to a circuit breaker
–
UL 1283
September 2009
thermally■protected,■50■kA■MOVs
-■ 10■year■warranty■
-■ ANSI/IEEE■C62.41.1-2002,■
(consult factory at time of order or see
100■kA■■■■■■■■■■■■50■kA■■■■50■kA
Audible alarm with silence switch
-■ –
Dry■contacts
– C62.41.2-2002,■and■C62.45-2002
Designed, manufactured & tested ■■ Available■Options
installation manual for retrofit)
and test button
-■ EMI/RFI■filtering
-■ Surge■counter
consistent with:
– 10 year warranty
-■ –
Dry contacts
■■ Standard■Monitoring
-■ 1992/2000■NEMA■LS-1
Protection■modes■on■L-N,■L-G,■L-L,■N-G
– ANSI/IEEE C62.41.1-2002,
–
filtering
■
LED■indicators
-■ NEC■Article■285
-■ I EMI/RFI
Rating■-■20■kA
C62.41.2-2002, and C62.45-2002
• Standard Monitoring
–n■Protection modes on L-N, L-G, L-L, N-G
Ordering■Information
■
Audible■alarm■with■silence■switch■and■test■
■
IEC■61643,■CE
Short■Circuit■Current■Rating■-■200■kA
– 1992/2000 NEMA LS-1
– LED indicators
-■ –I
n Rating - 20 kA
-■ Large■block,■individually■fused,■■
-■ –
Surge■Current■Rating
– NEC Article 285
button
– Audible alarm with silence switch and
Short Circuit Current Rating - 200 kA
Catalog■#■■
■
■
■
-■ Dry■contacts
test button
– IEC 61643, CE
thermally■protected,■50■kA■MOVs
Per■Phase■=■■L-N■+■■■L-G■■+■■■L-L
–
Surge Current Rating
– Dry contacts
Per
Phase= L-N+L-G
+L-L
150■kA■■■■■■■■50■kA■■50■kA■■■■50■kA
– Large block, individually fused,
■■ Available■Options
150kA 50kA 50kA 50kA
Voltage■Code
Surge■Current■(kA)
Options
thermally
protected, 50 kA MOVs
• Available
Options
-■ Surge■counter
A = 120/240V,■1Ø,■3W■(Fig■1)■
10 = 100■kA■per■phase
X = Surge■counter
TPS3 L2
TPS3 o 02
oo
o
– Surge counter
B = 120/240V,■3Ø,■4W■(Fig■3)
15 = 150■kA■per■phase
C = 120/208V,■3Ø,■4W■(Fig■2)■
20 = 200■kA■per■phase
Ordering■Information
D = 240V,■3Ø,■3W■(Fig■4)■
25 = 250■kA■per■phase
E = 277/480V,■3Ø,■4W■(Fig■2)
30 = 300■kA■per■phase
F = 480V,■3Ø,■3W■(Fig■4)
Catalog■#■
-■ Example:■■TPS3C0220X■=■SPD■for■a■208/120V■panelboard■with■a■surge■current■capacity■of■200■
G = 600V,■3Ø,■3W■(Fig■4)Œ
kA■per■phase■and■a■surge■counter■option
K = 380/220V,■3Ø,■4W■(Fig■2)
-■ When■surge■counter■is■not■selected,■include■a■zero■(0)■in■the■field
L = 600/347V,■3Ø,■4W■(Fig■2)
Voltage■Code
Surge■Current■(kA)
Options
Available■Accessories:■Ordered■Separately
S = 400/230V,■3Ø,■4W■(Fig■2)
A = 120/240V,■1Ø,■3W■(Fig■1)■
15 = 150■kA■per■phase
X = Surge■counter
-■ RMSIE■-■Remote■monitor
B = 120/240V,■3Ø,■4W■(Fig■3)■
30 = 300■kA■per■phase
C = 120/208V,■3Ø,■4W■(Fig■2)■
E = 277/480V,■3Ø,■4W■(Fig■2)■
K = 380/220V,■3Ø,■4W■(Fig■2)UL■1449■3rd■Edition■-■2009■Test■Data■Summary
■ Example:■■TPS3CL230X■=■10■Mode■SPD■for■a■208/120V■panelboard■with■a■
S = 400/230V,■3Ø,■4W■(Fig■2) -Voltage■Protection■Rating■■(VPR■-■6kV,■3kA)
TPS3
Voltage■Code
Service■Voltage
A
B
C
D
E
F
G
K
Voltage■Code
LA
SB
120/240V,■1Ø,■3W■(Fig■1)
120/240V,■3Ø,■4W■(Fig■3)
120/208V,■3Ø,■4W■(Fig■2)
240V,■3Ø,■3W■(Fig■4)
277/480V,■3Ø,■4W■(Fig■2)
480V,■3Ø,■3W■(Fig■4)
600V,■3Ø,■3W■(Fig■4)
380/220V,■3Ø,■4W■(Fig■2)
Service■Voltage
600/347V,■3Ø,■4W■(Fig■2)
120/240V,■1Ø,■3W■(Fig■1)
400/230V,■3Ø,■4W■(Fig■2)
120/240V,■3Ø,■4W■(Fig■3)
}V
}V
C
E
K
S
Hot (BLK)
Neutral (WHT)
Hot (BLK)
Ground (GRN)
V
V
Phase C (BLK)
Ground (GRN)
Figure■2
Hot (BLK)
V
}Split
2■Hots,■1■Neu,■1■Grnd
}V Neutral (WHT)
Wye Phase A (BLK)
Hi-Leg■Delta■(B■High)
B Phase B (BLK)
A
3■Hots,■1■Neu,■1■Grnd
3■Hots,■(B■High),■■
Neutral (WHT)1■Neu,■1■Grnd
N
Ground (GRN)
Notes:
Figure■4
Delta■&■HRG■Wye
3■Hots,■1■Grnd
Phase A (BLK)
Phase B (ORNG)
C
}
Phase C (BLK)
Ground (GRN)
}
V
Phase C (BLK)
Neutral (WHT)
Ground (GRN)
Figure 1
Figure 2
Figure 3
Split
2 Hots, 1 Neu, 1 Grnd
Wye
3 Hots, 1 Neu, 1 Grnd
Hi-Leg Delta (B High)
3 Hots, (B High),
1 Neu, 1 Grnd
Available■100■kA■&■150■kA■only
Phase B (BLK)
Ground (GRN)
Figure■3
V
Phase A (BLK)
5400■Triangle■Parkway
Norcross,■GA■30092
Phase C (BLK)
Neutral (WHT)
Ground (GRN)
Phase C (BLK)
Figure■1
Hot (BLK)
Œ
C
}
Neutral (WHT)
V
o
}
Phase B (ORNG)
B Phase B (BLK)
}
oo
surge■current■capacity■of■300■kA■per■phase■and■a■surge■counter■option
L-G
N-G
L-L
Type
In
SCCR
MCOV
-■ When■surge■counter■is■not■selected,■include■a■zero■(0)■in■the■field
700
700
700
1200
Type■4 20■kA 100■kA
150
Available■Accessories:■Ordered■Separately
700■■/■1200-■ RMSIE■-■Remote■monitor
700■/■1200
700
1800■/■1800 Type■4 20■kA 200■kA 150■/■320
700
700
700
1200
Type■4 20■kA 200■kA
150
1200
1200
Type■4 10■kA 200■kA
320
1200
1200
1200
2000
Type■4 20■kA 200■kA
320
UL■1449■3rd■Edition■-■2009■Test■Data■Summary
1800
1800
Type■4 10■kA 200■kA
550
Voltage■Protection■Rating■■(VPR■-■6kV,■3■kA)
2500
2500
Type■4 10■kA 200■kA
690
1200
1200
1200
2000
Type■4 20■kA
200■kA
320
L-N
L-G
N-G
L-L
Type■
In
SCCR
MCOV
1500
1500
1500
2500
Type■4 20■kA
10■kA 200■kA
420
700
700
700
1000
Type■4
100■kA
150
1200
1200
1200
2000
Type■4 20■kA
20■kA 200■kA
320
800■■/■1500 700■/■1200
700
1800■/■1800
Type■4
200■kA
150■/■320
700
700
700
1000
Type■4
20■kA 200■kA
150
1200
1200
1200
1800
Type■4
20■kA 200■kA
320
1200
1200
1200
1800
Type■4
20■kA 200■kA
320
1200
1200
1200
1800
Type■4
20■kA
200■kA
320
Siemens■Industry,■Inc.
Phase A (BLK)
Phase A (BLK)
N
L2
L-N
120/208V,■3Ø,■4W■(Fig■2)
277/480V,■3Ø,■4W■(Fig■2)
380/220V,■3Ø,■4W■(Fig■2)
400/230V,■3Ø,■4W■(Fig■2)
A
o
888-333-3545
info.us@siemens.com
■
©2010■Siemens■Industry,■Inc.
All■Rights■Reserved.■Siemens■is■a■registered
Siemens■Industry,■Inc.
trademark■of■Siemens■AG.■Product■names
5400■Triangle■Parkway
mentioned■may■be■trademarks■or■registered
Norcross,■GA■30092
trademarks■of■their■respective■companies.
Specifications■are■subject■to■change■without
888-333-3545
notice.
info.us@siemens.com
■
©2010■Siemens■Industry,■Inc.
www.usa.siemens.com/spd
All■Rights■Reserved.■Siemens■is■a■registered
trademark■of■Siemens■AG.■Product■names
mentioned■may■be■trademarks■or■registered
6.2.14.jb
trademarks■of■their■respective■companies.
Specifications■are■subject■to■change■without
notice.
P1 Panelboards • Quick reference for selection and application
www.usa.siemens.com/spd
23
Notes:
24
P1 Panelboards • Quick reference for selection and application
Notes:
P1 Panelboards • Quick reference for selection and application
25
The information provided in this brochure contains merely
general descriptions or characteristics of performance
which in case of actual use do not always apply as described
or which may change as a result of further development
of the products. An obligation to provide the respective
characteristics shall only exist if expressly agreed in the
terms of contract.
All product designations may be trademarks or product
names of Siemens AG or supplier companies whose use by
third parties for their own purposes could violate the rights
of the owners.
Siemens Industry, Inc.
5400 Triangle Parkway
Norcross, GA 30092
Subject to change without prior notice
Order No.: PDSA-P1QUI-1114
All rights reserved
Printed in USA
© 2014 Siemens Industry, Inc.
www.usa.siemens.com/panelboards