Casio CTK720AD - 12-NOTE Polyphonic Electronic Keyboard User`s guide

USER’S GUIDE
GUÍA DEL USUARIO
P
LK40/42-ES-1
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN
THE U.S.A. (not applicable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
CASIO ELECTRONICS CO., LTD.
Unit 6, 1000
North Circular Road
London NW2 7JD, U.K.
This mark is valid in the EU countries only.
Please keep all information for future reference.
478B-E-002A
Welcome...
To the happy family of satisfied CASIO electronic musical instrument owners! To get the most
out of the many features and functions of the keyboard, be sure to carefully read this manual
and keep it on hand for future reference.
Important!
When using batteries, be sure to replace them or shift to one of the alternate power sources
whenever you notice any of the following symptoms.
• Dim power supply indicator
• Instrument does not turn on
• Dim, difficult to read display
• Abnormally low speaker/headphone volume
• Distortion of sound output
• Occasional interruption of sound when playing at high volumes
• Sudden power failure when playing at high volumes
• Dimming of the display when playing at high volume
• Abnormal rhythm pattern and demo tune play
• Dimming of keyboard lights when notes sound
• Loss of power, sound distortion, or low volume when playing from a connected computer
or MIDI device
Main Features
❑ 100 amazingly realistic tones
❑ Enhanced auto-accompaniment function for greater versatility
• 100 built in auto-accompaniment patterns.
❑ 100 Built-in Song Bank tunes
• A total of 100 built-in Song Bank tunes comes built in for playback enjoyment or play-along
practice.
❑ A three-step lesson function lets you develop your musical skills by following
the keys as they light (Three Step Lesson System).
• First you become familiar with the timing of the notes by watching the keys light as you
playback one of the 100 built-in Song Bank tunes. Next, practice playing along at a pace
that’s comfortable for you. Finally, try playing along at the normal tempo for the Song Bank
tune.
❑ Auto Accompaniment
• Simply specify a chord and the keyboard automatically produces the matching rhythm,
bass, and chord patterns. One-touch fill-ins make accompaniments sound interesting and
natural.
❑ Transpose Function
• An easy operation instantly changes the key of the keyboard.
❑ MIDI compatibility
• Connecting to another MIDI device lets you sound notes on both this keyboard and the
connected device by playing on this keyboard. You can even playback commercially available pre-recorded MIDI data.
478B-E-003A
E-1
Safety Precautions
Symbols
Various symbols are used in this operating manual and on the product itself to ensure that the
product is used safely and correctly, and to prevent injury to the user and other persons as well
as damage to property. Those symbols along with their meanings are shown below.
WARNING
This indication stipulates matters that have the risk of causing death or serious injury if the
product is operated incorrectly while ignoring this indication.
CAUTION
This indication stipulates matters that have the risk of causing injury as well as matters for
which there is the likelihood of occurrence of physical damage only if the product is
operated incorrectly while ignoring this indication.
Symbol Examples
This triangle symbol ( ) means that the user should be careful. (The example at
left indicates electrical shock caution.)
This circle with a line through it ( ) means that the indicated action must not be
performed. Indications within or nearby this symbol are specifically prohibited.
(The example at left indicates that disassembly is prohibited.)
The black dot ( ) means that the indicated action must be performed. Indications
within this symbol are actions that are specifically instructed to be performed.
(The example at left indicates that the power plug must be unplugged from the
electrical socket.)
WARNING
Please use caution regarding the handling of the AC adaptor.
• Do not use a voltage other than the indicated power supply voltage. Use of a
voltage other than that indicated may cause fire or electrical shock.
• If the power cord should become damaged (exposed wires, disconnection,
etc.), purchase a new AC adaptor. Use of a damaged power cord may cause
fire or electrical shock.
• Do not cut or damage the power cord. Also do not place heavy objects on top
of it or subject it to excessive heat. Damage to the power cord may cause fire or
electrical shock.
• Do not attempt to shape the power cord or subject it to excessive bending,
twisting or pulling. This may cause fire or electrical shock.
• Please use the adaptor specified for this instrument. Use of another adaptor
may cause fire, electrical shock, or malfunction.
Do not locate the instrument or its stand on an uneven or unstable surface.
• Locating the instrument or its stand on an uneven or unstable surface can
cause it to fall, creating the danger of personal injury.
E-2
478B-E-004A
Do not place containers containing water or other liquids on the instrument.
• Do not place the following objects on the instrument. Placing such objects on
the instrument may cause fire or electrical shock if they spill and get inside the
instrument.
• Containers filled with water or other liquids (including vases, potted plants,
cups, cosmetics and medicines)
• Small metal objects (including hairpins, sewing needles and coins)
• Flammable objects
In the event a foreign object should happen to get inside the instrument,
please take the following actions:
1. Turn power off.
2. Unplug the AC adaptor from the wall outlet.
3. If there are any batteries loaded in the keyboard, remove them.
• Do not touch the batteries directly with your hands when removing them.
They may be hot or battery fluid may be leaking from them.
4. Consult with the dealer where you purchased the keyboard or with an
authorized CASIO service provider.
Do not disassemble or modify the instrument.
• Never attempt of take apart or modify the instrument, its accessories, or
separately sold options. Doing so may cause fire, electrical shock or malfunction. Consult your dealer concerning all inspection, adjustment or repair of
internal components.
Do not use if there is an abnormality or malfunction.
• Do not use the instrument if there appear to be abnormalities such as the
presence of smoke or abnormal odor. Also do not use the instrument if there
appear to be malfunctions such as the power not coming on or sound not
being produced. Use under such conditions may cause fire or electrical shock.
In such cases, take the following actions immediately. Never attempt to repair
the instrument yourself.
1. Turn power off.
2. Unplug the AC adaptor from the wall outlet.
3. If there are any batteries loaded in the keyboard, remove them.
• Do not touch the batteries directly with your hands when removing them.
They may be hot or battery fluid may be leaking from them.
4. Consult with the dealer where you purchased the keyboard or with an
authorized CASIO service provider.
When the instrument has been dropped:
• In the case the instrument has been dropped or damaged, take the following
actions. Continued use may cause fire or electrical shock.
1. Turn power off.
2. Unplug the AC adaptor from the wall outlet.
3. If there are any batteries loaded in the keyboard, remove them.
• Do not touch the batteries directly with your hands when removing them.
They may be hot or battery fluid may be leaking from them.
4. Consult with the dealer where you purchased the keyboard or with an
authorized CASIO service provider.
Be careful of the bags around children.
• Never allow anyone to place the plastic bags of the instrument, its accessories,
and its separately sold options over their heads. Doing so may cause suffocation. Particular caution is required in homes with small children.
478B-E-005A
E-3
CAUTION
AC Adaptor
• Do not locate the power cord in close proximity to heaters or other heating
appliances. This may cause the cord to melt leading to possible fire or electrical
shock.
• When unplugging the AC adaptor from an electrical outlet, always make sure to
pull on the adaptor itself and not the cord. Pulling excessively on the cord may
cause it to be damaged or break leading to possible fire or electrical shock.
• Do not touch the AC adaptor with wet hands when it is plugged in. This may
cause electrical shock.
• When not using the instrument for an extended period such as when traveling,
always make sure to unplug the AC adaptor from the electrical outlet for safety
reasons.
• After use turn off the power switch of the instrument and unplug the AC adaptor
from the electrical outlet.
• At least once a year, unplug the AC adaptor from the power outlet and clean the
area around the prongs of the plug. Dust build up around the prongs can create
the danger of fire.
Batteries
• Improper battery use may cause batteries to rupture and leak. This may cause
injury, malfunction of the instrument or discoloration of furniture and other
articles that come into contact with battery fluid. Take care to observe the following.
• Install batteries so their polarity (+/–) matches that indicated on the instrument.
• For safety and to prevent possible leakage of battery fluid, always make sure to
remove batteries from the instrument when you do not plan to use it for a long
time.
• Always make sure that the batteries making up a set are all of the same type.
• Never combine new batteries with old ones.
• Never dispose of batteries by incinerating them. Never short or disassemble
batteries, and do not expose them to excessive heat.
• Replace dead batteries as soon as possible.
• Never attempt to recharge batteries.
Transport
• When transporting the instrument, always make sure to unplug the AC adaptor
from the electrical outlet and confirm that all other external connections have
been disconnected. Only then should the instrument be transported. If the above
is not done, the cord may be damaged leading to possible fire or electrical shock.
Care
• Whenever caring, make sure to first unplug the AC adaptor from the electrical
outlet. Also remove the instrument’s batteries if battery power is being used.
Location
• Never locate the instrument in areas subject to high humidity or heavy accumulation of dust. Doing so may cause fire or electrical shock.
• Never locate the instrument in areas subject to grease splatters or steam, such as
in a kitchen or near a humidifier. Doing so may cause fire or electrical shock.
Do not place keyboard on lacquered furniture.
• The instrument’s silicone rubber feet may eventually blacken or scar lacquered
surfaces. Use felt cloth pads to insulate the feet or preferably use a CASIO musical
instrument stand designed for your keyboard.
E-4
478B-E-006A
Do not place heavy objects on the instrument.
• Do not place heavy objects on the instrument. This may cause the instrument to
tip over or break resulting in injury.
Volume
• Very high volume levels can damage hearing. Avoid using the instrument at very
high volume settings for long periods. Consult with a physician immediately if
you experience impaired hearing or ringing in the ears.
Do not get onto the instrument or stand.
• Do not crawl on top of the instrument or its optional stand. Particular caution is
required in homes having small children. This may cause the instrument or stand
to tip over and break resulting in injury.
Optional Stand (sold separately)
• Carefully assemble the stand following the assembly instructions that come with
it. Securely tighten all bolts, nuts, and fasteners, and make sure that you mount
the instrument correctly onto the stand. Incorrectly or insufficiently tightening
screws, or incorrectly mounting the instrument onto the stand can cause the stand
to tip over or the instrument to fall off the stand, possibly leading to injury.
Accessories and options
• Use only accessories that come with the instrument or authorized CASIO options
(sold separately). Use of non-specified accessories or options may cause fire,
electrical shock, or malfunction.
• You may not be able to see the keyboard keys light under direct sunlight or in
other brightly lit areas.
Care of Your Keyboard
Avoid heat, humidity or direct sunlight.
Do not overexpose the instrument to direct sunlight, or place it near an air conditioner,
or in any extremely hot place.
Do not use near a TV or radio.
This instrument can cause video or audio interference with TV and radio reception. If
this happens, move the instrument away from the TV or radio.
Do not use lacquer, thinner or similar chemicals for cleaning.
Clean the keyboard with a soft cloth dampened in a weak solution of water and a
neutral detergent. Soak the cloth in the solution and squeeze until it is almost dry.
Note
• You may notice lines in the finish of the case of this keyboard. These lines are a result
of the molding process used to shape the plastic of the case. They are not cracks or
breaks in the plastic, and are no cause for concern.
478B-E-007A
E-5
Contents
Welcome... ........................................................................................ E-1
Main Features ................................................................................... E-1
Safety Precautions ........................................................................... E-2
Care of Your Keyboard ................................................................... E-5
Contents ............................................................................................ E-6
Control Locations ............................................................................. E-8
Quick Reference ............................................................................ E-10
Connections ................................................................................... E-12
Phones/Output Jack .......................................................................................... E-12
Accessories and Options ..................................................................................... E-13
Power Supply .................................................................................. E-14
Using batteries ..................................................................................................... E-14
To load batteries ................................................................................................... E-14
Important Battery Information ............................................................................ E-14
Using the AC Adaptor ........................................................................................ E-15
Auto Power Off .................................................................................................... E-16
Power On Alert .................................................................................................... E-16
To disable Auto Power Off and power on alert .............................................. E-16
Basic Operations ............................................................................ E-17
To switch power on and off ............................................................................... E-17
To change tones ................................................................................................. E-17
Keyboard split tones ............................................................................................. E-18
Digital Sampling .................................................................................................... E-19
Polyphony .............................................................................................................. E-19
Other Useful Functions ........................................................................................ E-19
To change the key of the keyboard .................................................................. E-19
To tune the keyboard .......................................................................................... E-20
Playing the demo tunes ..................................................................................... E-21
To start demo tune play ....................................................................................... E-21
To stop demo tune play ....................................................................................... E-21
Playing rhythms ................................................................................................... E-22
To select and play a rhythm ................................................................................ E-22
E-6
478B-E-008B
Using auto-accompaniment ............................................................................. E-23
About the accompaniment keyboard .............................................................
Using the CASIO CHORD system .........................................................................
To play a CASIO CHORD auto-accompaniment .............................................
Using standard fingerings ....................................................................................
To play a FINGERED auto-accompaniment ......................................................
E-23
E-24
E-24
E-25
E-26
Improvising with the preset patterns ................................................................. E-27
Using fill-in rhythm ................................................................................................ E-27
Using Synchro start .............................................................................................. E-27
Three Step Lesson System .............................................................. E-28
Using Three Step Lesson System ........................................................................ E-28
Three Step Lesson System Tempo Setting ..........................................................
To play a built-in Song Bank tune .......................................................................
Using the Three Step Lesson System with Song Bank Tunes .............................
How the Three Step Lesson System operates in Steps 1 through 3 .................
Turning Off Key Lighting .......................................................................................
Number of Simultaneously Lit Keys .....................................................................
To change the tone used for the melody of a Song Bank tune .....................
E-29
E-29
E-30
E-31
E-32
E-32
E-32
Step 1: Easy Play .................................................................................................. E-33
Step 2: Slow Play ................................................................................................. E-33
Step 3: Normal Play ............................................................................................. E-34
To practice the left hand part ........................................................................... E-35
To check if the right hand or left hand part is currently selected
(two-hand tunes only) .......................................................................................... E-35
MIDI ................................................................................................. E-36
What is MIDI? ....................................................................................................... E-36
MIDI Connections ................................................................................................. E-36
MIDI Channels ....................................................................................................... E-37
General MIDI ....................................................................................................... E-37
Messages ............................................................................................................... E-37
Technical Reference ...................................................................... E-41
Troubleshooting ................................................................................................... E-41
Specifications ...................................................................................................... E-43
Appendix ......................................................................................... A-1
GM Tone Map List ................................................................................................ A-1
Rhythm List ............................................................................................................ A-3
Fingered Chord Charts ........................................................................................ A-4
MIDI Implementation Chart
478B-E-009A
E-7
Control Locations
J
Rear Panel
K
M
TU
DEMO
7
8
9
4
5
6
1
2
3
3-STEP LESSON
PHONES/
OUTPUT
DC 9V
OUT
MIDI
IN
RHYTHM
TRANSPOSE
TONE
STEP 1
0
STEP 3
TUNE
SONG BANK
NUMBER
V W
STEP 2
TEMPO
:VALUE UP
TEMPO
:VALUE DOWN
L
Q
N
O
*
P
Q
DEMO
POWER/MODE
SYNCHRO/
FILL-IN
VOLUME
START/
STOP
TEMPO
7
8
9
4
5
6
KEY LIGHT
3-STEP LESSON
FINGERED
ON
CASIO CHORD
NORMAL
1
2
0
NUMBER
TRANSPOSE
TONE
STEP 1
ONE KEY PLAY
R
RHYTHM
3
OFF
STEP 3
STEP 2
TUNE
SONG BANK
TEMPO
:VALUE UP
TEMPO
:VALUE DOWN
S
1 2
3
POWER/MODE
6
SYNCHRO/
FILL-IN
7
8 9
B
CD
E
FG
START/
STOP
VOLUME
TEMPO
KEY LIGHT
FINGERED
ON
CASIO CHORD
NORMAL
OFF
ONE KEY PLAY
45
E-8
0 A
H
I
478B-E-010A
1 POWER/MODE selector
J Number buttons
2 Power indicator
K DEMO button
3 VOLUME buttons
L 3-STEP LESSON buttons
4 SYNCHRO/FILL-IN button
5 START/STOP button
M TRANSPOSE/TUNE operation
guide
6 TEMPO buttons
N 100 RHYTHMS list
7 KEY LIGHT button
See “Rhythm List” on page A-3 for details.
8 STEP 1 icon
O 100 TONES list
9 STEP 2 icon
P 100 SONG BANK list
0 STEP 3 icon
Q Speakers
A SONG BANK icon
R CHORD ROOT NAMES
B Display
S Percussion instrument list
C RHYTHM icon
T DC 9V jack
D TONE icon
U PHONES/OUTPUT jack
E PART SELECT button
F TONE button
G RHYTHM button
H ONE KEY PLAY buttons
For connection of commercially available headphones. Output from the
speakers is automatically cut when
headphones are connected.
V MIDI OUT terminal
W MIDI IN terminal
I SONG BANK button
* Attachment of Score Stand
Insert the score stand into the slot at the top of the keyboard as shown in the
illustration.
478B-E-011A
E-9
Quick Reference
This section provides a quick overview of keyboard operation using steps one and
two of the 3-step lesson feature. See page E-28 for detailed explanations of these steps.
1
3
2
Set the POWER/MODE
selector to NORMAL.
Press the SONG BANK
button.
Find the tune yo
Song Bank list,
number button
number.
POWER/MODE
• To select “20 AM
[2] and the [0].
FINGERED
ON
CASIO CHORD
NORMAL
OFF
SONG BANK icon lights.
POWER/MODE
SYNCHRO/
FILL-IN
VOLUME
START/
STOP
TEMPO
ON
7
8
9
4
5
6
1
2
3
0
NUMBER
KEY LIGHT
FINGERED
CASIO CHORD
NORMAL
STEP
OFF
ONE KEY PLAY
5
Play the melody part on the keyboard.
<If you pressed
Play the notes o
<If you pressed the STEP 1 button in 4 ...>
Play the notes with the ONE KEY PLAY buttons.
• The accompaniment tempo automatically adjusts to play
along with your melody.
ONE KEY PLAY
E-10
478B-E-012A
• Keep the key d
• If you selected
goes out as soo
• The key that co
you need to pla
• After you press
accompanimen
3
Find the tune you want to play in the
Song Bank list, and then use the
number buttons to input its two-digit
number.
• To select “20 AMAZING GRACE”, input
[2] and the [0].
ghts.
8
9
4
5
6
1
2
3
0
NUMBER
4
Press the STEP 1 button or
STEP 2 button.
DEMO
NCHRO/
FILL-IN
E
7
START/
STOP
TEMPO
7
8
9
4
5
6
1
2
3
KEY LIGHT
3-STEP LESSON
RHYTHM
TRANSPOSE
TONE
STEP 1
0
ONE KEY PLAY
STEP 3
NUMBER
STEP 2
TUNE
SONG BANK
TEMPO
:VALUE UP
TEMPO
:VALUE DOWN
• When you do, the STEP 1 icon
or STEP 2 icon lights.
• The keyboard sounds a count
beat and waits for you to play
something on the keyboard.
The keys that you need to press
first flash.
3-STEP LESSON
STEP 1
STEP 3
STEP 2
<If you pressed the STEP 2 button in 4 ...>
Play the notes on the keyboard, pressing keys as they light.
ons.
to play
• Keep the key depressed as long as it stays lit.
• If you selected any song from number 85 through 99, the lit key
goes out as soon as you press it.
• The key that corresponds to the next note
you need to play will flash.
• After you press the correct melody key,
accompaniment proceeds to the next note.
478B-E-013A
E-11
Connections
■ Phones/Output Jack
Before connecting headphones or other external equipment, be sure to first turn
down the volume settings of the keyboard and the connected equipment. You can
then adjust volume to the desired level after connections are complete.
[Rear Panel]
PHONES/OUTPUT Jack
DC 9V
OUT
MIDI
IN
PHONES/
OUTPUT
1
Standard plug
3
Keyboard amp,
guitar amp,etc.
White
2
Red
PIN plug
LEFT RIGHT
AUX IN or similar terminal
of audio amplifier
Connecting Headphones (Figure 1)
Connecting headphones cuts off output from the keyboard’s built-in speakers, so you
can play even late at night without disturbing anyone.
Audio Equipment (Figure 2)
Connect the keyboard to an audio equipment using a commercially available connecting cord with a standard plug on one end and two PIN plugs on the other end. In
this configuration, you normally set the input selector of the audio equipment to the
terminal (usually marked AUX IN or something similar) where the cord from the
keyboard is connected. See the user documentation that comes with your audio
equipment for full details.
Musical Instrument Amplifier (Figure 3)
Use a commercially available connecting cord to connect the keyboard to a musical
instrument amplifier.
Note
• Be sure to use a connecting cord that has standard plugs on the ends you connect to
the keyboard and amplifier.
E-12
478B-E-014B
Connection Example
To keyboard’s
PHONES/OUTPUT
jack
INPUT
Standard plug
Keyboard or guitar amp
Accessories and Options
Use only the accessories and options specified for this keyboard. Use of non-authorized items creates the danger of fire, electrical shock, and personal injury.
478B-E-015B
E-13
Power Supply
This keyboard can be powered by current from a standard household wall outlet
(using the specified AC adaptor) or by batteries. Always make sure you turn the
keyboard off whenever you are not using it.
■ Using batteries
Always make sure you turn off the keyboard before loading or replacing batteries.
To load batteries
1. Remove the battery compartment cover.
2. Load 6 AA-size batteries into the battery compartment.
• Make sure that the positive (+) and negative (–) ends
are facing correctly.
3. Insert the tabs on the battery compartment cover into the
holes provided and close the cover.
The keyboard may not function correctly if you load or replace batteries with power
turned on. If this happens, turning the keyboard off and then back on again should
return functions back to normal.
Important Battery Information
■ The following shows the approximate battery life provided by different battery
types.
• Standard battery life: Approximately 1 hour (SUM3/R6P)
Approximately 4 hours (AM3/LR6)
Both of the above values are standard battery life at normal temperature, with the
keyboard volume at a medium setting. Temperature extremes or playing at very
loud volume settings can shorten battery life.
■ Any of the following symptoms indicate low battery power. Replace batteries as
soon as possible whenever any of the following occurs.
• Dim power supply indicator
• Instrument does not turn on
• Dim, difficult to read display
• Abnormally low speaker/headphone volume
• Distortion of sound output
• Occasional interruption of sound when playing at high volumes
• Sudden power failure when playing at high volumes
• Dimming of the display when playing at high volume
• Abnormal rhythm pattern and demo tune play
• Dimming of keyboard lights when notes sound
• Loss of power, sound distortion, or low volume when playing from a connected computer or MIDI device
E-14
478B-E-016A
Important!
Improper handling of batteries can cause them to burst and leak, which creates the
danger of personal injury or damage due to contact with battery acid. Be sure to note the
following important precautions.
• Always make sure that the positive (+) and negative (–) poles are facing correctly as
indicated inside the battery compartment.
• To avoid damage caused by leaking batteries, be sure to remove batteries from the
keyboard whenever you leave it unattended for long periods (such as when leaving
on a trip).
• Never mix batteries of different types.
• Never mix old batteries with new ones.
• Never discard batteries by incinerating them, do not allow their poles to be shorted
(connected to each other), never take batteries apart, and do not expose batteries to
direct heat.
• Replace batteries as soon as possible after any sign they are getting weak.
• Never attempt to recharge batteries.
■ Using the AC Adaptor
Make sure that you use only the AC adaptor specified for this keyboard.
Specified AC Adaptor: AD-5
DC 9V jack
DC 9V
OUT
MIDI
IN
AC adaptor AD-5
PHONES/
OUTPUT
AC outlet
Also note the following important warnings and precautions when using the AC
adaptor.
Warning!
• Take care to avoid any damage to or breakage of the power cord. Never place any
heavy objects on the power cord or expose it to direct heat. Doing so creates the
danger of power cord damage, fire, and electrical shock.
• Use only the specified AC adaptor. Use of another type of adaptor creates the danger
of fire and electrical shock.
478B-E-017A
E-15
Caution!
• For safety sake, be sure to unplug the AC adaptor from the wall outlet whenever
leaving the keyboard unattended for a long time (such as when leaving on a trip).
• Always turn off the keyboard and unplug the AC adaptor from the wall outlet when
you are not using the keyboard.
Important!
• Make sure that the keyboard is turned off before connecting or disconnecting the AC
adaptor.
• Using the AC adaptor for a long time can cause it to become warm to the touch. This
is normal and does not indicate malfunction.
■ Auto Power Off
When you are using battery power, keyboard power turns off automatically whenever you leave it on without performing any operation for about 6 minutes. When
this happens, move the POWER/MODE selector to the OFF position and then back to
NORMAL, CASIO CHORD, or FINGERED to turn power back on.
Note
• Auto Power Off is disabled (it does not function) when you are using the AC adaptor
to power the keyboard.
■ Power On Alert
Keyboard keys light to alert you if you leave power on and do not perform any
operation for about 6 minutes. Note that keys light only, and no sound is produced.
When this happens, press any button or keyboard key to clear the power on alert.
Note
• Power on alert operates only when you are powering the keyboard using the AC
adaptor. It does not operate when you are using batteries.
■ To disable Auto Power Off and power on alert
Hold down the TONE button while turning on the keyboard to disable Auto Power
Off and power on alert.
• When these functions are turned off, the keyboard does not turn off automatically
and no alert is performed no matter how long it is left with no operation being
performed.
• Auto Power Off and power on alert are enabled again when you manually turn off
power and then turn it back on again.
E-16
478B-E-018A
Basic Operations
This part of the manual provides you with the basic information you need to use your
keyboard.
■ To switch power on and off
1. Set the POWER/MODE selector to NORMAL.
POWER/MODE
FINGERED
ON
CASIO CHORD
NORMAL
OFF
2. Press the keyboard keys.
3. The VOLUME up and down arrow buttons are used to adjust main volume.
• Pressing
or
displays the currently set volume setting. Press
or
again to change the volume setting.
• Volume can be adjusted over a range of 0 (minimum) to 9 (maximum).
• Volume is set to 7 when the power is turned on.
• A setting of 0 turns down the volume completely.
• The volume can be changed continuously by continuously pressing
down the
or
buttons.
• Pressing the
and
buttons simultaneously sets the volume to level
7.
• Numeric values can be entered directly with the number buttons after
the VOLUME button has been pressed in step 3.
• The amount that the volume settings raises or lowers the volume level
differs according to the tone, auto accompaniment, or song you are
using.
VOLUME
4. To switch power off, set the POWER/MODE selector to OFF position.
POWER/MODE
FINGERED
ON
CASIO CHORD
NORMAL
OFF
■ To change tones
1. Look at the tone list printed on the keyboard’s console and find the one you want.
• A total of 100 tones are available.
2. Press the TONE button.
• When you do, the TONE icon lights.
• The number for the tone that is currently
selected is shown on the display.
478B-E-019A
TONE icon
E-17
3. Use the number buttons to input the 2-digit number that identifies the tone you want to
select.
7
8
9
4
5
6
1
2
3
0
NUMBER
• Always enter two digits for the tone number. If you enter only one
digit, the display will automatically return to the previous tone number
setting after a few seconds.
• If you change the tone setting while a keyboard key is depressed, the
tone does not change until you release the key and press a keyboard
key again.
• With certain tones (such as percussion sounds and sound effects), there
may be very little or no change at all in the pitch, no matter which
keyboard key you press.
• If you input the wrong first digit for a tone number, you can return to
the previous setting by pressing the TONE button.
Keyboard split tones
Some of the preset tones split the keyboard and assign two or more sounds. With
such a preset tone, the sound produced depends on what position of the keyboard
you play. For example, BASS/PIANO (tone 90) puts BASS on the left and PIANO on
the right of the keyboard.
<Example>
BASS/PIANO (No.90)
BASS
PIANO
PERCUSSION (No.99)
• PERCUSSION (tone 99) assigns 35 percussion sound to the keyboard as illustrated
below. The sound assigned to each key are indicated above the keyboard.
BASS DRUM
HIGH MID TOM
HIGH BONGO
SIDE STICK
CRASH CYMBAL 1
LOW BONGO
ACOUSTIC SNARE
HIGH TOM
MUTE HIGH CONGA
HAND CLAP
RIDE CYMBAL 1
OPEN HIGH CONGA
ELECTRIC SNARE
CHINESE CYMBAL
LOW CONGA
LOW FLOOR TOM
RIDE BELL
HIGH TIMBALES
CLOSED HI-HAT
TAMBOURINE
LOW TIMBALES
HIGH FLOOR TOM
SPLASH CYMBAL
HIGH AGOGO
PEDAL HI-HAT
COWBELL
LOW AGOGO
LOW TOM
CRASH CYMBAL 2
CABASA
OPEN HI-HAT
CLAVES
MARACAS
LOW MID TOM
RIDE CYMBAL 2
L
H
E-18
478B-E-020A
• There are no sounds assigned to any keyboard keys from B4 onward when the “99
PERCUSSION” tone is selected.
Digital Sampling
A number of the tones that are available with this keyboard have been recorded and
processed using a technique called digital sampling. To ensure a high level of total
quality, samples are taken in the low, mid, and high ranges and then combined to
provide you with sounds that are amazingly close to the originals. You may notice
very slight differences in volume or sound quality for some tones when you play
them at different positions on the keyboard. This is an unavoidable result of multiple
sampling, and it is not a sign of malfunction.
Polyphony
The term polyphony refers to the maximum number of notes you can play at the
same time. This keyboard has 12-note polyphony, which includes the notes you play
as well as the rhythms and auto-accompaniment patterns that are played by the
keyboard. This means that when a rhythm or auto-accompaniment pattern is being
played by the keyboard, the number of notes (polyphony) available for keyboard
play is reduced. Also note that some of the tones offer only 6-note polyphony.
• When rhythm or auto accompaniment is playing, the number of sounds simultaneously played is reduced.
• Though you can sound up to 12 notes at one time, only the last four keyboard keys
pressed light up.
■ Other Useful Functions
To change the key of the keyboard
The transpose feature of this keyboard lets you raise or lower its key in semitone
increments. This means you can easily match to suit someone’s voice, and you can
eliminate sharps and flats from music making it easier to play.
1. While in any mode besides the Song Bank Mode (indicated when the SONG BANK icon is
lit), hold down the TONE button and press the RHYTHM button.
• Perform step 2 within five seconds after performing
step 1.
2. Use the TEMPO buttons to change the key of the keyboard.
TEMPO
• Example: To change the tuning to B (indicated by -1
since it is one tone below C, which is the normal
tuning of the keyboard).
• See page E-20 for the indicator that appears for each
key.
F G A
C D
C D E F G A B C
478B-E-021A
Normal tuning
B
E
B (-1) tuning
Indicator remains on the display for a few
seconds.
C
B
E-19
<Keys and their indicators>
Key :
F#
A
G
A
B
B
C
C#
D
E
E
F
Display :
: Pressing
: Pressing
<Note Names>
C
D
E
F
G
A
B
C
Notes
• You cannot change the transpose setting while the keyboard is in the Song Bank
Mode.
• In step 2 of the above operation, you could also use the number buttons [0] to [5] to
specify C through F.
• Pressing both of the TEMPO buttons ( / ) at the same time returns the transpose
setting to C(0).
• The transpose setting is automatically set to C(0) whenever you turn keyboard power
on.
• The transpose setting is automatically set to C(0) whenever you press the SONG
BANK button.
• The pitch of a transposed note depends on the tone you are using. If the transpose
operation causes a note to exceed its upper range, the same note from the lowest
octave available is substituted.
• The transpose operation does not affect tone number 99 (PERCUSSION) or autoaccompaniment rhythms.
• Transposing tones 75 through 79 and 90 through 96 changes the range of keys to
which each of the tones is assigned.
• The transpose setting is automatically set to C(0) whenever you press the DEMO
button.
To tune the keyboard
A simple operation lets you tune the keyboard to another musical instrument.
1. While in any mode besides the Song Bank Mode (indicated when the SONG BANK icon is
lit), hold down the TONE button and press the SONG BANK button.
• Perform step 2 within five seconds after performing
step 1.
2. Use the TEMPO buttons to change the tuning of the keyboard.
TEMPO
Indicator remains on the
display for a few seconds.
E-20
478B-E-022A
Notes
• In step 2 of the above procedure, you could also use the number buttons to input a
value from 00 to 50.
• Pressing both of the TEMPO buttons ( / ) at the same time returns the tuning
setting to 00.
• Pressing the SONG BANK button changes the tuning setting to 00.
• The tuning setting does not affect any of Song Bank tunes.
• You can tune the keyboard within a range of approximately ±50 cents (100 cents = 1
semitone).
• The tuning setting is automatically set to 00 whenever you turn the keyboard on.
• Pressing the DEMO button changes the tuning setting to 00.
• The tuning operation does not affect rhythm (percussion).
■ Playing the demo tunes
You can set up the keyboard to continually play its 100 built-in Song Bank tunes.
Keyboard keys light to indicate the melody notes of the demo tune as it plays.
To start demo tune play
1. Switch power on and adjust the volume level.
2. Press the DEMO button.
• Demo tune play continues in a sequential endless loop until you switch
it off.
• The number of the demo tune currently playing is shown on the display.
• You can play along on the keyboard while a demo tune is playing back.
DEMO
3. You can change the demo tune play being played by pressing the number buttons.
7
8
9
4
5
6
1
2
3
0
NUMBER
• The Song Bank tunes play back in tune number sequence, starting from
the one you select.
To stop demo tune play
Press the DEMO button again to stop demo tune play.
DEMO
Notes
• Only the following buttons are enabled while a Song Bank tune is being played.
• VOLUME buttons
• Number buttons
• START/STOP button
• POWER/MODE selector (OFF)
• DEMO button
• KEY LIGHT button
• You cannot change the tone being used for the melody of a Song Bank tune.
478B-E-023A
E-21
■ Playing rhythms
This keyboard features a collection of 100 exciting built-in rhythm patterns. Each
pattern provides percussion back up for all your performances.
To select and play a rhythm
1. Set the POWER/MODE selector to NORMAL.
POWER/MODE
FINGERED
ON
CASIO CHORD
NORMAL
OFF
2. Find the rhythm you want to use in the “Rhythm List” (page A-3) and note its rhythm number.
3. Press the RHYTHM button.
• When you do, the RHYTHM icon lights.
• The number that appears on the display indicates the currently selected rhythm.
RHYTHM icon
4. Use the number buttons to input the 2-digit rhythm number for the rhythm you want to use.
7
8
9
4
5
6
1
2
3
0
NUMBER
• Example: To select “71 SAMBA”, input 7 and 1.
• Be sure to always specify a 2-digit number.
• If you discover a mistake before you input the second
digit, press the RHYTHM button to return to the
previously set rhythm number.
• You can change to another rhythm even while the
current rhythm is sounding.
5. Press the START/STOP button to start play of the rhythm.
SYNCHRO/
FILL-IN
START/
STOP
• When you do, the selected rhythm starts to sound.
6. Use the TEMPO buttons to adjust the tempo of the rhythm.
TEMPO
E-22
• Pressing
or
displays the current tempo setting. Press
or
again to change the tempo setting.
• Each time you press one of the TEMPO buttons while
the tempo value is displayed, the tempo setting
changes one step, within the range of 040 to 255.
• The initial default tempo setting when you turn on
power is 120.
• After displaying the current tempo setting by pressing a TEMPO button in step 6, you can also input the tempo setting you want by inputting a three-digit value with the number buttons.
478B-E-024A
• Holding down either of the TEMPO buttons changes the tempo setting
at high speed.
• To reset the tempo to the standard value of each rhythm, press both
TEMPO buttons.
7. To stop rhythm play, press the START/STOP button again.
SYNCHRO/
FILL-IN
START/
STOP
■ Using auto-accompaniment
This keyboard features 100 accompaniment patterns that let you add full accompaniments to your performances automatically. With auto-accompaniment, part of the
keyboard is reserved as an accompaniment keyboard. As you play your chords on
the accompaniment keyboard, the accompaniment patterns adjusts automatically to
follow the progression you play.
You get a choice between two different methods for chord play. FINGERED lets you
play chords as you normally do, while CASIO CHORD makes it possible to play fully
formed chords with one finger.
About the accompaniment keyboard
The lower (left) 1.5 octaves are reserved for use as an accompaniment keyboard
whenever you select CASIO CHORD or FINGERED with the POWER/MODE selector. The panel above the accompaniment keyboard keys is marked with the names of
the notes they play. The remainder of the keyboard (the part that is not included in
the accompaniment keyboard) is called the melody keyboard. Please be sure to
remember these terms, because they will be used throughout the rest of this manual.
Accompaniment
keyboard
Melody keyboard
entire keyboard can be used for melody play while
( The
)
the POWER/MODE selector is set to NORMAL.
478B-E-025A
E-23
Using the CASIO CHORD system
The CASIO CHORD system lets you easily play the four main types of chords. Play of
chords is simplified as shown in the chart below.
Keys
Chord Type
Example
Pressing one
accompaniment
key
Major chord
C
(C Major Chord)
CDE F GAB C DE F
Pressing two
accompaniment
keys
Minor chord
Cm
(C Minor Chord)
CD E F G A B C D E F
Pressing three
accompaniment
keys
Seventh chord
C7
(C Seventh Chord)
CDE F GAB C DE F
Pressing four
accompaniment
keys
Minor seventh
chord
Cm7
(C Minor Seventh
Chord)
CDE F GAB C DE F
Notes
• The bottom (leftmost) note that you play determines the name of the chord. If the
bottom note is a C for example, the keyboard produces a C chord.
• When pressing more than one accompaniment key, it makes no difference whether
the keys to the right of the bottom note are white or black.
To play a CASIO CHORD auto-accompaniment
1. Use the POWER/MODE selector to select CASIO CHORD.
POWER/MODE
FINGERED
ON
CASIO CHORD
NORMAL
OFF
2. Select an auto-rhythm as described under “To select and play a rhythm” on page E-22.
3. Start play of the rhythm.
SYNCHRO/
FILL-IN
E-24
START/
STOP
• If you want start play of the normal rhythm pattern, press START/
STOP.
• You can also use synchro start (page E-27) to start rhythm play.
478B-E-026A
4. Press either one or up to four keys on the accompaniment keyboard, and the corresponding
accompaniment starts to play automatically.
5. Continue pressing different keys on the accompaniment keyboard to play your chord
progression.
6. To stop auto-accompaniment play, press the START/STOP button again.
SYNCHRO/
FILL-IN
START/
STOP
Using standard fingerings
The FINGERED mode lets you play a wider variety of chords. In this mode, you can
start play of an accompaniment pattern by pressing three or four of the accompaniment keyboard keys.
This keyboard is capable of recognizing 15 different chords. The following shows the
fingerings of these chords with a root of C. Note that you can omit the fifth notes
(which are shown inside parentheses in the illustrations below) to produce 7, m7,
maj7, add9 and mM7 chords.
C
Cm
Cdim
Caug (*1)
Csus4
C7
Cm7
Cmaj7
Cm7-5
C7-5 (*1)
CmM7
Cdim7(*1)
(
C7sus4
)
(
)
Cadd9
(
)
Cmadd9
(
)
(
)
(
)
*1 With this chords, the lowest note in your fingering is always used as the root. Make
sure that your fingering correctly identifies the root you want to use.
478B-E-027A
E-25
Important!
• If you play one or two notes only in the left hand, or three notes that do not make up
a recognizable chord formation, no sound will be produced. FINGERED mode
requires a conventional three or four-note chord formation to produce an autoaccompaniment. Also, note that auto-chords only work in conjunction with rhythm
patterns, and not independently of them.
Notes
• The above examples show only one of the possible fingerings for each chord. Note
that you can play the notes that form a chord in any combination. Each of the
following fingerings for example, produces the same C chord.
Accompaniment keyboard
• See the “Fingered Chord Charts” on page A-4 for information on the fingerings of
chords for all roots.
To play a FINGERED auto-accompaniment
1. Use the POWER/MODE selector to select FINGERED.
POWER/MODE
FINGERED
ON
CASIO CHORD
NORMAL
OFF
2. Select an auto-rhythm as described under “To select and play a rhythm” on page E-22.
3. Start play of the rhythm.
SYNCHRO/
FILL-IN
START/
STOP
• If you want start play of the normal rhythm pattern, press START/
STOP.
• You can also use synchro start (page E-27) to start rhythm play.
4. Play a chord on the accompaniment keyboard to start play of the auto-accompaniment.
5. Continue pressing keys on the accompaniment keyboard to play your chord progression.
6. To stop auto-accompaniment play, press the START/STOP button again.
SYNCHRO/
FILL-IN
E-26
START/
STOP
478B-E-028A
■ Improvising with the preset patterns
Pressing the START/STOP button to start rhythm play causes the normal version of
the pattern to be played. You can also play a variation of the rhythm using the
operation described below.
■ Using fill-in rhythm
You can insert a fill-in rhythm by pressing the SYNCHRO/FILL-IN button while an
auto-rhythm plays.
SYNCHRO/
FILL-IN
START/
STOP
■ Using Synchro start
You can start the rhythm and accompaniment pattern at the same time, with your
play of the accompaniment keyboard. To do this, follow the steps below.
1. Set the POWER/MODE selector to the CASIO CHORD or FINGERED position.
POWER/MODE
FINGERED
ON
CASIO CHORD
NORMAL
OFF
2. Select an auto-rhythm.
3. Press the SYNCHRO/FILL-IN button.
SYNCHRO/
FILL-IN
START/
STOP
4. Press the accompaniment keys to play the first chord. As soon as you do, the autoaccompaniment pattern begins to play.
5. To stop the auto-accompaniment pattern play, press the START/STOP button.
SYNCHRO/
FILL-IN
START/
STOP
Note
• If you set the POWER/MODE selector to NORMAL in step 1 on page E-22, the
operation in step 4 starts play of the rhythm (percussion instruments) only.
478B-E-029A
E-27
Three Step Lesson System
■ Using Three Step Lesson System
Even individuals who cannot play the keyboard at all can follow along with the 100
built-in Song Bank tunes with the ONE KEY PLAY buttons. You can also use the
Three Step Lesson System to learn at your own pace. Play slowly at first until you are
able to play along at normal speed.
Of the 100 built-in tunes, numbers 00 through 84 feature auto-accompaniment (autoaccompaniment tunes), while 85 through 99 are played using both hands (two-hand
tunes).
The Three Step Lesson System can be used with the following three-step lesson plan
to master keyboard play.
Step 1: Easy Play
Pressing the ONE KEY PLAY buttons plays the melody for an auto-accompaniment tune or the right hand part for two-hand tunes. In both cases, the autoaccompaniment (the right hand part in the case of two-hand tunes) is played
automatically by the keyboard. In place of the ONE KEY PLAY buttons, you
can also press any key of the keyboard to play the melody or right hand part.
The purpose of this step is to familiarize yourself with the timing required to
play melody notes.
Step 2: Slow Play
Press the keys that light as they teach you the correct notes to play. You can
play at the pace you want, because the auto-accompaniment or left hand part
waits until you press the correct key.
Step 3: Normal Play
At this level, the keyboard’s keys still light to indicate which notes to play, but
they no longer wait for you to press the correct key. The auto-accompaniment
or left hand part is played at normal speed.
Notes
• You may not be able to see the keyboard keys light under direct sunlight or in other
brightly lit areas.
• You can press the ONE KEY PLAY, STEP 1, STEP 2, and STEP 3 buttons at any time,
except while a demo tune is playing. To return the keyboard to its normal mode,
press the SONG BANK button.
E-28
478B-E-030A
Three Step Lesson System Tempo Setting
You can use the procedure in step 6 of the procedure on page E-22 to set the tempo of
the left-hand part for Song Bank and Three Step Lesson System play (Step 1 through
3).
This means you can use a slower tempo at the beginning, and then increase it as you
learn. Press both of the TEMPO buttons ( and ) at the same time to return the
tempo to its initial preset setting.
To play a built-in Song Bank tune
1. Look up the number of the tune you want to play in the Song Bank list.
2. Press the SONG BANK button until the SONG BANK icon lights.
• The number that appears is the currently
selected Song Bank number.
SONG BANK icon
3. Input the two digit number for the tune you want to play.
7
8
9
4
5
6
1
2
3
0
NUMBER
4. Press the START/STOP button to start play of the selected tune.
SYNCHRO/
FILL-IN
START/
STOP
• The tune you select plays repeatedly, with the keyboard keys lighting
to indicate the melody notes.
5. To stop Song Bank tune play, press the START/STOP button again.
SYNCHRO/
FILL-IN
START/
STOP
6. To exit the SONG Mode, press the SONG BANK button again.
• When you do, the SONG BANK icon goes out.
• At this time the tone number or rhythm number appears on the display.
478B-E-031A
E-29
Notes
• Always enter two digits for the Song Bank number.
• You can input a Song Bank tune number even while another Song Bank tune is
playing.
• If you input the wrong first digit for a Song Bank tune number, you can return to the
previous setting by pressing the SONG BANK button.
• The RHYTHM button is disabled in the Song Bank Mode. If you want to play a
rhythm, press the SONG BANK button to return to the normal mode first.
Using the Three Step Lesson System with Song Bank Tunes
When you use a Song Bank tune with melody guide, the Three Step Lesson System
teaches you which melody notes to play.
Auto-accompaniment Song Bank Tune
Chord and melody part keys light.
Chord
The root (the C-note of a C-chord)
and other notes that make up the
chord alternately light.
Melody note lights.
Note
• Some Song Bank tunes use chords (such as C6) that cannot be played with the
FINGERED setting (page E-25). In the FINGERED Mode, even if you finger the
chords according to the keys that are lit by Melody Guide, chords may sound
different from the ones produced during Melody Guide play.
Two-hand Song Bank Tune
Left hand and right hand part keys light.
Left hand part
E-30
Right hand part
478B-E-032A
How the Three Step Lesson System operates in Steps 1 through 3
When using an auto-accompaniment Song Bank tune with the Three Step Lesson
System, the lights indicate not only the note you should play, but how long you
should play it (how long you should keep the key depressed). The following describes what illumination of keys indicates.
• Note Guide: A lit key indicates the note to be played.
• Length Guide: Key remains lit for as long as note should be played.
• Next Note Guide: A flashing key indicates the next note to be played.
• Consecutive Note Guide: When a key lights, goes out momentarily, and then lights
again, it indicates that the same note should be played in succession.
First note length
Flashes
Lights
Goes out
1
First Note
2
Press
Release
Flashes
Lights
Goes out
4
3
Second Note
Press
Release
Second note length
Note lengths are not indicated by the Three Step Lesson System when playing a twohand tune with Step 1 and Step 2. The lit key goes out as soon as you press the correct
keyboard key and the next note’s key flashes.
Lights
Flashes
(Next note to be played.)
Goes out
Lights
When playing a two-hand tune with Step 3, the applicable keyboard key remains lit
as long as its note plays. In this case, however, the key for the next note to be played
does not flash. Keys light when their notes start to play.
478B-E-033A
E-31
Turning Off Key Lighting
1. Press the KEY LIGHT button.
KEY LIGHT
• Press the KEY LIGHT button again to turn key lighting back on.
Note
• Key lighting turns on automatically in any of the following cases:
• When keyboard power is turned on.
• When demo tune play is started.
• When the SONG BANK button is pressed in the normal mode (page E-29 to steps
1 to 3).
• When the power on alert function operates (page E-16).
Number of Simultaneously Lit Keys
Up to four keyboard keys can be lit at the same time.
To change the tone used for the melody of a Song Bank tune
1. Following step 3 of the procedure on page E-29, press the TONE button.
• Both the SONG BANK icon and TONE icon light,
along with the tone number of the tone that is currently assigned to the keyboard.
2. Input a value to select the tone you want to use.
7
8
9
4
5
6
1
2
3
0
NUMBER
• Example: 30 VIOLIN
Notes
• You cannot change the tone of the two-hand Song Bank tunes (number 85 through
99).
• Selecting another Song Bank tune switches the tone setting to the newly selected
tune’s preset melody tone.
• The tone assigned to the keyboard is the same one specified for the melody of the
Song Bank tune.
• The above procedure can be used to change the Song Bank melody tone before
starting play or while play is already in progress.
E-32
478B-E-034A
■ Step 1: Easy Play
You can press the ONE KEY PLAY buttons or any of the keyboard keys to play along
with the melody (right hand part) of the Song Bank tune. You do not have to worry
about pressing the right key, so you can concentrate on getting the timing right.
1. Press the STEP 1 button.
3-STEP LESSON
STEP 1
STEP 3
STEP 2
• When you do, the STEP 1 icon lights.
• After a count sounds, the keyboard stands by and waits
for you to play the first note of the tune. If the tune includes intro measures, the keyboard enters standby after
the intro measures are complete.
STEP 1 icon
2. Press the ONE KEY PLAY buttons to play each note of the tune.
ONE KEY PLAY
• The accompaniment (left hand) part of the tune follows along as you
play the melody (right hand) part.
• The keyboard key that corresponds to the next note to be played
flashes, and lights when you play the note.
• The rhythm (percussion) part does not sound.
3. Try pressing any one of the keyboard keys in place of the ONE KEY PLAY buttons.
• Pressing any keyboard key plays the correct melody (right hand part) note.
• Pressing more than one (up to four) keyboard keys plays the corresponding number
of melody notes.
The correct note is played even if you do
not press the key that is lit.
4. To interrupt an Easy Play session, press the START/STOP button.
SYNCHRO/
FILL-IN
START/
STOP
• When you do, the STEP 1 icon goes out.
■ Step 2: Slow Play
With Slow Play, you have to play the note that the Three Step Lesson System
indicates. But don’t worry - the accompaniment (left hand part) waits until you can
play the correct note before continuing. This means you can take your time and play
at your own pace.
1. Press the STEP 2 button.
3-STEP LESSON
STEP 1
STEP 3
STEP 2
478B-E-035A
• When you do, the STEP 2 icon lights.
• After a count sounds, the keyboard stands by and waits
for you to play the first note of the tune. If the tune includes intro measures, the keyboard enters standby after
the intro measures are complete.
STEP 2 icon
E-33
2. Play the notes indicated by the Three Step Lesson System.
• The accompaniment (left hand) part of the tune follows along as you play the melody
(right hand) part.
• The keyboard key that corresponds to the next note to be played flashes, and lights
when you play the note.
• The rhythm (percussion) part does not sound.
Press keyboard keys as they light. More
than one key may light when you are playing a two-hand tune. Press all keys that
light.
3. To interrupt an Slow Play session, press the START/STOP button.
SYNCHRO/
FILL-IN
START/
STOP
• When you do, the STEP 2 icon goes out.
■ Step 3: Normal Play
Normal Play also shows you which notes to play, but unlike Slow Play, it does not
wait for you to press the key. The accompaniment part is played at normal speed, no
matter what you play (or don’t play) on the keyboard.
1. Press the STEP 3 button.
3-STEP LESSON
STEP 1
STEP 3
• When you do, the STEP 3 icon lights.
• Play starts after a count sounds.
STEP 3 icon
STEP 2
2. Play along on the keyboard, following the keys as they light.
• The accompaniment (left hand) part of the tune plays at normal speed, regardless of
what you play on the keyboard.
• With a auto-accompaniment tune, the keyboard key that corresponds to the next note
to be played flashes, and lights when the note should be played.
• With a two-hand tune, the applicable keyboard key remains lit as long as its note
plays. In this case, however, the key for the next note to be played does not flash.
Keys light when their notes start to play.
3. To interrupt a Normal Play session, press the START/STOP button.
SYNCHRO/
FILL-IN
E-34
START/
STOP
• When you do, the STEP 3 icon goes out.
478B-E-036A
■ To practice the left hand part
Once you master right hand part play, you can use the two-hand tunes (numbers 85
through 99) to practice left hand part.
1. Press the STEP 1, STEP 2, or STEP 3 button.
3-STEP LESSON
STEP 1
• When you do, the STEP 1, STEP 2, or STEP 3 icon lights.
STEP 3
STEP 2
2. Press the PART SELECT button to switch the left hand play.
• After a count beat sounds, the right-hand part starts to play and the
keys for the left-hand part notes flash.
3. Press the PART SELECT button to return the part selection to its previous setting.
4. To interrupt play of the melody, press the START/STOP button.
SYNCHRO/
FILL-IN
START/
STOP
• When you do, the STEP 1, STEP 2, or STEP 3 icon goes out.
Note
• The PART SELECT button is operational only while STEP 1, STEP 2, or STEP 3 is
playing or paused (by the START/STOP button).
To check if the right hand or left hand part is currently selected
(two-hand tunes only)
The Three Step Lesson System tells you what part is selected whenever you press the
STEP 3 button. Pressing the STEP 3 button causes the leftmost three keys to light
when the left hand part is selected, and the rightmost three keys to light when the
right hand part is selected.
Left hand part selected
478B-E-037A
Right hand part selected
E-35
MIDI
■ What is MIDI?
The letters MIDI stand for Musical Instrument Digital Interface, which is the name of
a worldwide standard for digital signals and connectors that makes it possible to
exchange musical data between musical instruments and computers (machines) produced by different manufacturers. MIDI compatible equipment can exchange keyboard key press, key release, tone change, and other data as messages.
Though you do not need any special knowledge about MIDI to use this keyboard as a
stand-alone unit, MIDI operations require a bit of specialized knowledge. This section provides you with an overview of MIDI that will help to get you going.
MIDI Connections
MIDI messages are send out through the MIDI OUT terminal of one machine to the
MIDI IN terminal of another machine over a MIDI cable. To send a message from this
keyboard to another machine, for example, you must use a MIDI cable to connect the
MIDI OUT terminal of this keyboard to the MIDI IN terminal of the other machine.
To send MIDI messages back to this keyboard, you need to use a MIDI cable to
connect the other machine’s MIDI OUT terminal to the MIDI IN terminal of this
keyboard.
To use a computer or other MIDI device to record and playback the MIDI data
produced by this keyboard, you must connect the MIDI IN and MIDI OUT terminals
of both machines in order send and receive data.
MIDI IN
MIDI OUT
MIDI IN
MIDI OUT
Computer etc.
E-36
478B-E-038A
MIDI Channels
MIDI allows you to send the data for multiple parts at the same time, with each part
being sent over a separate MIDI channel. There are 16 MIDI channels, numbered 1
through 16, and MIDI channel data is always included whenever you exchange data
(key press etc.)
Both the sending machine and the receiving machine must be set to the same channel
for the receiving unit to correctly receive and play data. If the receiving machine is set
to Channel 2, for example, it receives only MIDI Channel 2 data, and all other
channels are ignored.
With this keyboard, messages received over MIDI Channels 1, 2, 3, 4, and 10 can be
used for multi-timbre play of up to five different instrument parts. The tone and
volume settings for these five channels must be controlled by messages sent from an
external device.
Conversely, keyboard operations are sent to external devices over MIDI Channel 1.
■ General MIDI
General MIDI standardizes MIDI data for all sound source types, regardless of
manufacturer. General MIDI specifies such factors as tone numbering, drum sounds,
and available MIDI channels for all sound sources. This standard makes it possible
for all MIDI equipment to reproduce the same nuances when playing General MIDI
data, regardless of the manufacturer of the sound source.
Though the sound source of this keyboard is not General MIDI compatible, you can
still connect the keyboard to a computer or other MIDI equipment to playback
General MIDI data that is widely available in stores, over computer networks, and
from other sources.
Notes
• General MIDI data made up of a large number of parts may not play correctly on this
keyboard.
• You will have most success playing back General MIDI data that has few parts and is
made up of data on channels 1, 2, 3, 4, and 10.
Messages
There is a wide variety of messages defined under the MIDI standard, and this
section details the particular messages that can be sent and received by this keyboard.
478B-E-039A
E-37
■ NOTE ON/OFF
This message sends data when a key is pressed (NOTE ON) or released (NOTE OFF).
A NOTE ON/OFF message include a note number (to indicate note whose key is
being pressed or released) and velocity (keyboard pressure as a value from 1 to 127).
NOTE ON velocity is always used to determine the relative volume of the note. This
keyboard does not receive NOTE OFF velocity data.
Whenever you press or release a key on this keyboard, the corresponding NOTE ON
or NOTE OFF message is sent by constant velocity from the MIDI OUT terminal.
■ PROGRAM CHANGE
This is the tone selection message. PROGRAM CHANGE can contain tone data
within the range of 0 to 127.
A PROGRAM CHANGE message (0 to 99) is sent out through this keyboard’s MIDI
OUT terminal whenever you manually change its tone number. Receipt of a PROGRAM CHANGE message from an external machine changes the tone setting of this
keyboard.
This keyboard can send tone data within the range of 00 to 99 and receive tone data
within the range of 0 to 127*.
* When GM mapping is turned on. When turned off, tone data is received in the
range of 0 to 99.
Note
• Channel 10 is for the drum part only, and it does not receive Program Change
messages. When receiving MIDI data, it sounds percussion sounds produced by this
keyboard.
■ PITCH BEND
This message carries pitch bend information for smoothly sliding the pitch upwards
or downwards during keyboard play. This keyboard does not send pitch bend data,
but is can receive such data.
■ CONTROL CHANGE
This message adds effects such as vibrato and volume changes applied during
keyboard play. CONTROL CHANGE data includes a control number (to identify the
effect type) and a control value (to specify the on/off status and depth of the effect).
The following is a list of data that can be received using CONTROL CHANGE.
Effect
VOLUME
HOLD1
MODULATION
E-38
Control Number
7
64
1
478B-E-040A
■ LOCAL CONTROL (Default: on) /GM mapping (Default: off)
This setting determines whether or not the keyboard and sound source of this
keyboard are connected internally. When recording to a computer or other external
device connected to this keyboard’s MIDI IN/OUT terminal, it helps if you turn
LOCAL CONTROL off.
on: Anything played on the keyboard is sounded by the internal sound source and
simultaneously output as a MIDI message from the MIDI OUT terminal.
oFF: Anything played on the keyboard is output as a MIDI message from the MIDI
OUT terminal, without being sounded by the internal sound source. Turn LOCAL CONTROL off whenever you are using the MIDI THRU function of a
computer or other external device. Also note that no sound is produced by the
keyboard if LOCAL CONTROL is turned off and no external device is connected.
MIDI THRU
MIDI OUT
Sound Source
LOCAL CONTROL On
Notes played on the keyboard are
sounded by the internal sound source
and output as MIDI messages from the
MIDI OUT terminal.
478B-E-041A
MIDI IN
MIDI OUT
MIDI IN
MIDI OUT
Sound Source
LOCAL CONTROL Off
Notes played on the keyboard are output as MIDI messages from the MIDI
OUT terminal, but not sounded directly by the internal sound source. The
MIDI THRU terminal of the connected
device can be used to return the MIDI
message and sound it on this keyboard’s sound source.
E-39
■ To turn off LOCAL CONTROL
While holding down the RHYTHM button, press the SONG BANK button.
• This also turns on GM mapping.
■ To turn on LOCAL CONTROL
While holding down the RHYTHM button, press the PART SELECT button.
• This turns off GM mapping.
Note that LOCAL CONTROL is also turned on automatically when any of the
following buttons are pressed.
POWER (to turn on power), START/STOP (to start rhythm or Song Bank
tune play), ONE-KEY PLAY, STEP 1, STEP 2, STEP 3, DEMO (to start demo
tune play).
Note
• See the GM Tone Map List at the back of this manual for information about tone
assignments while GM mapping is turned on.
E-40
478B-E-042A
Technical Reference
■ Troubleshooting
Be sure to check the following table whenever you experience problems with keyboard operation.
Symptom
• No sound when keyboard
keys are pressed.
Cause
1. Power supply problem.
2. Volume is set to 0.
3. Headphones are plugged
into the keyboard.
4. The POWER/MODE selector is in the CASIO CHORD
or FINGERED position.
5. Tone “99 PERCUSSION” is
selected and you are pressing keys that are not assigned tones.
• Any of the following symptoms while using battery
power.
•
•
•
•
•
•
•
•
•
•
•
• Low battery power
Action
1. Correctly attach the AC
adaptor, make sure that batteries poles (+/–) are facing
correctly, and check to make
sure that batteries are not
dead.
2. Press the VOLUME
button.
3. Unplug the headphones
from the PHONES/OUTPUT jack.
4. Normal play is not possible
on the accompaniment keyboard while the POWER/
MODE selector is set to
CASIO CHORD or FINGERED. Change the
POWER/MODE selector
setting to NORMAL.
5. While “99 PERCUSSION” is
selected, you can use only
keys to the left of B4. These
keys are marked on the console with illustrations of
percussion instruments.
• Replace the batteries with a
set of new ones or use the
AC adaptor.
Dim power supply indicator
Instrument does not turn on
Dim, difficult to read display
Abnormally low speaker/
headphone volume
Distortion of sound output
Occasional interruption of
sound when playing at high
volumes
Sudden power failure when
playing at high volumes
Dimming of the display
when playing at high volume
Abnormal rhythm pattern
and demo tune play
Dimming of keyboard lights
when notes sound
Loss of power, sound distortion, or low volume when
playing from a connected
computer or MIDI device
478B-E-043A
E-41
Symptom
Cause
Action
• Keyboard keys remain lit.
• Keyboard is standing by for
keyboard play in Step 2.
• Press the lit keys and continue with Step 2 play.
• Press the START/STOP button to stop Step 2.
• Keyboard keys light but no
sound is produced.
• Power on alert is telling you
that power is left on.
• Press any button or keyboard key to resume normal operation with the keyboard in its initial power on
setting.
• RHYTHM button does not
work.
• Keyboard is in the Song
Bank Mode.
• Press the SONG BANK button to return to the Normal
Mode.
• Song Bank tone does not
change.
• A two-hand Song Bank tune
(number 85 through 99) is
selected.
• Change to an auto accompaniment Song Bank tune
(number 00 to 84). You cannot change the tone setting
of a two-hand Song Bank
tune (number 85 through
99).
• Cannot change TRANSPOSE/TUNE settings.
• Keyboard is in the Song
Bank Mode.
• Demo tune play is in
progress.
• Press the SONG BANK button to return to the Normal
Mode.
• Stop demo tune play.
• Cannot play correctly even
when the lit keyboard keys
are pressed with Step 1.
• More than one key is being
pressed at the same time,
which causes accompaniment to advance the corresponding number of notes
(up to four).
• When using Step 1, press
keyboard keys one by one.
• No sound is produced
when playing MIDI data
from a computer.
• MIDI cables are not connected properly.
• Connect MIDI cables properly.
• Playing on the keyboard
produces an unnatural
sound when connected to a
computer.
• The computer’s MIDI THRU
function is turned on.
• Turn off the MIDI THRU
function on the computer or
turn off LOCAL CONTROL
on the keyboard.
E-42
478B-E-044A
■ Specifications
Model:
LK-40/LK-42
Keyboard:
61 standard-size keys; 5 octaves
Key Light System:
Can be turned on and off (up to 4 keys can be lit at the
same time)
Tones:
100 presets
Polyphony:
12 notes maximum
Three Step Lesson System: Number of simultaneosly lit keys; 4
Three steps
Playback: 1 tune repeat playback
Auto-accompaniment:
Rhythm patterns
100 presets
Tempo
Adjustable, (216 steps, = 40 to 255),
initial value: 120
Chords Two systems: CASIO CHORD, FINGERED
Other
Fill-in pattern, Synchro start
Song Bank tunes:
100 tunes
Other Functions:
Transpose (F# to C to F: half-note)
Tuning
Adjustable A4 = Approx. 440 Hz, ±50 cents,
Initial value: A4 = Approx. 440 Hz
MIDI:
5 multi-timbre receive
Speakers:
10 cm diameter x 2 (Output: 2W+2W)
Digital Volume Control:
Main volume; 10 steps (0 to 9), initial value: 7
I/O Terminals:
MIDI Terminals
Power Supply
Headphones/Output
Power Supply:
2-way AC/DC power sources;
Batteries
6 AA-size
Battery life
approximately 1 hour
on R6P (SUM3)
manganese batteries/
4 hours on LR6 (AM3)
alkaline batteries
AC adaptor
AD-5
Auto Power Off:
Approximately 6 minutes after the last operation
(Operates during battery use only)
Power Consumption:
9V
Dimensions:
94.4 x 36.3 x 11.8 cm (37 3/16" x 14 5/16" x 4 5/8")
Weight:
Approximately 4.5 kg (9.9 lbs) (without batteries)
IN, OUT
DC 9V jack
Stereo standard jack
(Output is monaural.)
[output impedance: 78Ω, output voltage: 4V (RMS) MAX],
7.7 W
* Designs and specifications are subject to change without notice.
478B-E-045A
E-43
Appendix/Apéndice
■ GM Tone Map List
■ Lista de asignaciones de sonido GM
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
478B-E-091A
Tone No./Tone Name
GM No.
Nº de sonido/Nombre de sonido
Nº GM
GRAND PIANO
BRIGHT PIANO
HONKY-TONK
E GRAND PIANO
ELEC PIANO 1
ELEC PIANO 2
ELEC PIANO 3
ELEC PIANO 4
HARPSICHORD
CLAVI
ELEC ORGAN 1
ELEC ORGAN 2
ELEC ORGAN 3
ELEC ORGAN 4
CHURCH ORGAN
PIPE ORGAN
REED ORGAN
ACCORDION
BANDONEON
HARMONICA
NYLON STR GT
STEEL STR GT
JAZZ GUITAR
CLEAN GUITAR
MUTE GUITAR
DIST GUITAR
ACOUSTIC BASS
ELEC BASS
SLAP BASS
BANJO
VIOLIN
CELLO
HARP
STRINGS 1
STRINGS 2
STRINGS 3
SYNTH-STR 1
SYNTH-STR 2
CHOIR AAHS
SYNTH-VOICE
TRUMPET
TUBA
BRASS SECTION
FRENCH HORN 1
FRENCH HORN 2
BRASS 1
BRASS 2
0
1
3
2
4
5
8
9
6
7
16
17
18
15
19
104
20
21
23
22
24
25
26
27
28
29
32
33
36
105
40
42
45
48
49
44
50
51
52
53
56
58
57
60
59
61
69
30
31
34
37
35
41
43
46
55
84
47
91
85
A-1
Tone No./Tone Name
GM No.
Nº de sonido/Nombre de sonido
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
A-2
SYNTH-BRASS 1
SYNTH-BRASS 2
SYNTH-BRASS 3
SOPRANO SAX
ALTO SAX
TENOR SAX
OBOE
CLARINET
PICCOLO
FLUTE
RECORDER
FLUTE ENSEMBLE
WHISTLE
SYNTH-LEAD 1
SYNTH-LEAD 2
SYNTH-LEAD 3
CALLIOPE
SYNTH-PAD 1
SYNTH-PAD 2
SYNTH-PAD 3
BOWED GLASS
HALO PAD
SYNTH-BASS
RAIN DROP
SF
SOUNDTRACK
SPACE PAD
SYNTH-SFX
VEHICLE
TELEPHONE
SPACE
INVADER
FUNNY
STRINGS PIANO
STRINGS EP
CHOIR EP
CHOIR ORGAN
STRINGS GUITAR
STRINGS HARP
BRASS STRINGS
VIB PAD
12STR GUITAR
CHOIR STRINGS
BASS/PIANO
BASS/E PIANO
BASS/VIB
BASS/NYLON STR GT
BASS/DIST GUITAR
STRINGS/PIANO
STRINGS/TRUMPET
VIBRAPHONE
MARIMBA
PERCUSSION
Nº GM
62
63
70
64
65
66
68
71
72
73
74
75
78
87
81
80
82
89
90
95
92
54
38
96
103
97
101
102
125
124
126
127
123
106
88
108
109
99
111
112
113
114
115
100
117
118
119
120
121
122
10
12
83
67
79
76
77
86
93
94
39
98
107
110
116
11
13
14
478B-E-092A
■ Rhythm List
■ Lista de ritmos
POPS I
00
01
02
03
04
05
06
07
08
09
CLUB POP
FUNKY POP 1
RAP POP
FUNKY POP 2
SOUL BALLAD
POP BALLAD
LOVE BALLAD
FUNKY POP 3
EPIC BALLAD
LITE POP
POPS II
10
11
12
13
14
15
16
17
18
19
16 BEAT SHUFFLE
16 BEAT POP
16 BEAT FUNK
8 BEAT POP
8 BEAT SOUL
8 BEAT SHUFFLE
DANCE POP 1
DANCE POP 2
POP FUSION
FOLKIE POP
ROCK I
20
21
22
23
24
25
26
27
28
29
ROCK WALTZ
SLOW ROCK 1
SLOW ROCK 2
SOFT ROCK 1
SOFT ROCK 2
SOFT ROCK 3
POP ROCK 1
POP ROCK 2
50’S ROCK
60’S SOUL
ROCK II
30
31
4 BEAT ROCK
ROCK
478B-E-093A
32
33
34
35
36
37
38
39
HEAVY ROCK
8 BEAT ROCK
STRAIGHT ROCK
HEAVY METAL
TWIST
NEW ORLNS R&R
CHICAGO BLUES
R&B
JAZZ/FUSION
40
41
42
43
44
45
46
47
48
49
BIG BAND
SLOW SWING
SWING
FOX TROT
JAZZ WALTZ
MODERN JAZZ
COOL
HARD BOP
ACID JAZZ
LATIN FUSION
DANCE/FUNK
50
51
52
53
54
55
56
57
58
59
TECHNO POP
RAVE
CLUB GROOVE
TECHNO
TRANCE
HOUSE
GROOVE SOUL
DISCO
RAP
FUNK
EUROPEAN
60
61
62
63
64
65
POLKA 1
POLKA 2
MARCH 1
MARCH 2
WALTZ
VIENNESE WALTZ
66
67
68
69
FRENCH WALTZ
SLOW WALTZ
SERENADE
TANGO 1
LATIN I
70
71
72
73
74
75
76
77
78
79
BOSSA NOVA
SAMBA
MAMBO
RHUMBA
CHA-CHA-CHA
MERENGUE
REGGAE
BOLERO
TANGO 2
LAMBADA
LATIN II/VARIOUS I
80
81
82
83
84
85
86
87
88
89
PUNTA
CUMBIA
SKA
TEX-MEX
SALSA
FOLKLORE
PASODOBLE
RUMBA CATALANA
SEVILLANA
FOLK
VARIOUS II
90
91
92
93
94
95
96
97
98
99
COUNTRY
BLUEGRASS
TOWNSHIP
FAST GOSPEL
SLOW GOSPEL
ADANI
BALADI
BAROQUE
ENKA
NEW AGE
A-3
A-4
478B-E-094A
F /(G )
G
(G )/A
A
(A )/B
F /(G )
G
(G )/A
A
(A )/B
B
F
F
B
E
E
Ackordtyp
(D )/E
Rot
(D )/E
dim7
D
m7
D
7
C /(D )
m
C /(D )
M
C
Ackordtyp
C
Rot
■ Cuadros de acordes digitados
■ Fingered Chord Charts
M7
m7-5
dim
aug
sus4
478B-E-095A
A-5
C
Ackordtyp
B
(A )/B
A
(G )/A
G
F /(G )
F
E
(D )/E
D
C /(D )
Rot
7sus4
m add9
mM7
7-5
add9
Acordes con las mismas notas componentes como B
aumentada ... E aumentada, G aumentada.
No puede especificarse en el ajuste FINGERED debido a las
limitaciones del teclado de acompañamiento, pero en su
lugar pueden usarse los acordes aumentados compuestos
por las mismas notas componentes (con diferente nota
básica).
Acordes con las mismas notas componentes como B aumentada ... D aumentada, F aumentada.
aug
Chords with same component notes as B aug.....E aug, G
aug
Cannot be specified in FINGERED setting because of accompaniment keyboard limitations, but augmented chords
made up of the same component notes (with different base
note) can be used instead.
Chords with same component notes as B aug.....D aug, F
478B-E-096A
478B-E-097A
478B-E-098A
478B-E-099A
478B-E-100A
478B-E-101A
478B-E-102A
Control
Change
O
X
O
X
X
O
X
X
X
X
X
X
X
X
X
X
X
X
1
6,38
7
10
11
64
100,101
120
121
X
X
O
X
X
Key’s
Ch’s
After
Touch
O 9nH v = 1-127
X 9nH v = 0,8nH v = *3
X
O 9nH v = 75, 100 *2
X 9nH v = 0
Note ON
Note OFF
Velocity
Pitch Bender
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
True voice
0-127
36-96 *1
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
36-96
Mode 3
X
Mode 3
X
Default
Messages
Altered
Mode
Note
Number:
1-4, 10
1-4, 10
Recognized
1
1
Transmitted
MIDI Implementation Chart
Default
Changed
Function ...
LK-40
LK-42
Basic
Channel
Model
Hold1
RPN LSB, MSB
All sound off
Reset all controller
Modulation
Data entry
Volume
Pan
Expression
*3 = no relation
*1: Depends on tone
Remarks
Version: 1.0
478B-E-103A
X
X
X
: Song Pos
: Song Sel
: Tune
X
: Clock
: Commands X
System
Common
System
Real Time
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
O : Yes
X : No
*2: V(Velocity)=100 when note on data when the main volume value of this unit is 9
to 2, and V=75 when the main volume value is 1 or 0.
Remarks
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
X
X
X
X
X
X
X
X
X
X
X
X
X
: Local ON/OFF
: All notes OFF
Messages : Active Sense
: Reset
Aux
X
X
*4: Depends on GM Map
setting
O 0-127, 0-99 *4
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
O 0-99
❊❊❊❊❊❊❊❊❊❊❊❊❊❊
True #
Hold1
RPN LSB, MSB
All sound off
Reset all controller
O
X
X
X
X
X
X
X
64
100,101
120
121
System Exclusive
Program
Change:
Control
Change
Modulation
Data entry
Volume
Pan
Expression
O
X
O
X
X
X
X
X
X
X
1
6,38
7
10
11
This recycle mark indicates that the packaging conforms to
the environmental protection legislation in Germany.
Esta marca de reciclaje indica que el embalaje se ajusta a
la legislación de protección ambiental en Alemania.
CASIO COMPUTER CO.,LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan
P
MA0104-B
Printed in Malaysia
LK40/42-ES-1