Audiovox GMRS762CH Owner`s manual

General Mobile Radio Service (GMRS)
Model : GMRS762CH
Ultra-Slim Twin Pack
Owner’s
Manual
HI LO FM
Customer Service
1-800-290-6650
Released: 2-10-06
128-7627
1 of 28
THIS PAGE LEFT BLANK INTENTIONALLY
2
128-7627
2 of 28
CAUTION:
SAFETY INFORMATION
Your wireless hand-held portable transceiver contains a power transmitter. When the PTT button is pushed (or the VOX mode is enabled) it
sends out radio frequency (RF) signals. The device is authorized to
operate at a duty factor not to exceed 50%. In August 1996, the Federal
Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for hand-held wireless devices.
Important: To maintain compliance with the FCC’s RF exposure guidelines hold the transmitter at least 1 inch (2.5 centimeters)
from your face and speak in a normal voice, with the an
tenna pointed up and away. If you wear the handset on your
body while using the headset accessory, use only the
Audiovox supplied carry clip for this product and ensure that
the antenna is at least 1 inch (2.5 centimeters) from your
body when transmitting. Use only the supplied antenna. Do
not use your transceiver with a damaged antenna. Unauthorized antennas, modifications, or attachments could
damage the transmitter and may violate FCC regulations.
Performance:
Your transceiver will only achieve its maximum operating range when
communicating with other transceivers across open and flat areas or
between elevated points. Normally occurring environmental factors such
as buildings, trees, terrain and weather, or interference from other radio
or electrical equipment, may have adverse effects on the transceiver’s
effective range. These are not indicative of a fault condition.
Avoid placing the GMRS762CH radio transceiver for prolonged periods
of time in direct sunlight or temperatures below -4°F(-20°C) or above
140°F (60°C).
3
128-7627
3 of 28
WARNINGS:
Battery Care
Never attempt to charge other brands of batteries, as batteries may
burst causing personal injury and damage to the product. When recharging Lithium-ion(Li-ion) batteries with the AUDIOVOX charger, use only
supplied Audiovox-approved rechargeable batteries. Use of the Audiovox
charger (also supplied) with other brands of batteries is not recommended,
as battery charging times will vary with different brands. Refer to the
Manufacturer’s instructions for charging other brands of batteries.
Battery Disposal
In general, if handled improperly, batteries pose a risk of fire or burns. Do
not disassemble, crush, puncture, short external contacts, or dispose of
the batteries in fire or water. Dispose of the batteries in a environmentally
safe manner and recycle whenever possible.
CAUTION: Make sure wrist strap is securely fastened to wrist strap ring
to prevent unit loss or damage.
FCC WARNING
Replacement or substitution of transistors, diodes or other parts of a unique
nature, with parts other than those recommended by the manufacturer,
may cause a violation of the technical regulations of Part 15 of FCC Rules.
GMRS LICENSE:
USE OF THIS RADIO WITHIN THE UNITED STATES REQUIRES AN
FCC GMRS LICENSE. AN INDIVIDUAL 18 YEARS OF AGE OR OLDER,
WHO IS NOT A REPRESENTATIVE OF A FOREIGN GOVERNMENT, IS
ELIGIBLE TO APPLY FOR A GMRS SYSTEM LICENSE. YOU WILL
NEED TWO FORMS FROM THE FCC: FCC FORM 159, AND FCC
FORM 605 (MAIN FORM AND SCHEDULE F). YOU CAN FIND THE
FORMS ONLINE AT: HTTP: // WWW. FCC. GOV / FORMPAGE. HTML, OR
CALL 1-800-418-3676.
128-7627
4 of 28
4
Model GMRS762CH (FCC License Required)
10
11
9
12
3
8
13
2
7
14
4
9
REF
17
6
15
1
5
16
1. Battery (Internally Installed)
2. Flashlight Enable Button
3. Push-To-Talk (PTT) Button
4. Antenna
5. VOX/LOCK Button
6. MODE Button
7. Built-in Microphone
8. Power On-Off/SCAN
Button
9. Wrist strap ring
10. White Flashlight LED
11. External Speaker/Microphone/Charge Jack
12. Liquid Crystal Display
(LCD)
13. Down Channel/Volume
Button
14. Monitor/Backlight Button
15. Up Channel/Volume Button
16. Built-in Speaker
17. Battery Charging Contacts
5
128-7627
5 of 28
Model GMRS762CH Display
4
5
6
7
8
9
10
11
3
HI LO FM
2
13
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
12
14
Small Segment Display: Displays the CTCSS tone option for
each main channel from 01-38.
Large Segment Display: Indicates the channel number in use.
Dual Watch Mode Indicator: Indicator appears when dual watch
mode is active.
Signal Receive Indicator: Busy icon appears when a signal is
being received.
Signal Strength Indicator: Icon appears when a signal is being
transmitted.
Key Lock Indicator: Icon appears when the keypad is locked.
This function disables keys such as channel up/down, SCAN and
MODE.
Monitor Indicator: Icon appears when the Monitor (M) button is
pressed and the channel monitor function is activated.
Beep Tone Indicator: Icon appears when beep button confirmation tone is selected; icon disappears when tone is off.
Roger Beep Tone On/Off Indicator: This icon appears when the
Roger Beep tone is on, and disappears when tone is not in use.
Battery Level Indicator: Icon indicates when the battery is low
and in need of charging.
6
128-7627
6 of 28
11. Scan Indicator: This function allows the user to scan a channel
(and tone code, if present) every .5 second to search for a valid
signal.
12. Voice Activated Transmission (VOX) Indicator: This function
allows hands free conversation. The indicator appears when the
VOX mode is activated.
13. HI/LO Indicators: Power level indicator appears when the
transmit power is set to desired output power on the GMRS
channels.
14. Volume Level Indicator: Indicator appears the volume level
Equipment and Accessories Supplied
1. Radio (2)
2. Owner’s Manual
3. Dual Desktop Charger
. 4. AC Wall Adapter
5. Rechargeable (Li-ion) Battery
6. Wrist Strap
GMRS762CH
128-7627
GMRS6DST
GMRS6AC
GMRS5BAT
GMRS5WRST
Powering the transceiver:
Your GMRS762CH radio transceiver operates on internally installed
Li-ion batteries. Only Audiovox approved rechargeable batteries should
be recharged in the radio transceiver using the charging accessories.
This will ensure optimum performance for the GMRS762CH. Battery
charging time is typically 11 - 13 hours. Use of the Audiovox charging
equipment with other brands of rechargeable batteries is not recommended as battery charging times will vary. Refer to the
manufacturer’s instructions for charging other brands of batteries.
CAUTION:
Prior to initial use, make sure to fully charge the LithiumIon battery; otherwise, if the battery is allowed to discharge too much, battery damage could result. The
battery should be fully charged in approximately 12 hours.
7
128-7627
7 of 28
Battery Charging
Use only an Audiovox approved rechargeable battery and charging equipment when charging the battery internal to the unit.
WARNING: Do not attempt to charge the battery using another
manufacturer’s charging equipment.
NOTE: To extend battery life, avoid overcharging the battery. Do not leave
the unit(s) in the charger for extended periods of time.
CHARGING STAND
PWR JACK
DC 9V
+
ADAPTER
POWER
PLUG
AC WALL ADAPTER/
CHARGING TRANSFORMER
MODEL: GMRS6AC
INPUT: 120VAC
OUTPUT: 9.0 VDC
CHARGING
COMPARTMENT
CONTACTS
RED LED: ON - CHARGING
OFF - CHARGING
COMPLETE
GMRS RADIO
CHARGING
COMPARTMENTS
(2)
DESKTOP CHARGING STAND
MODEL GMRS6DST
CHARGING
COMPARTMENT
LEDs:
ON - CHARGING
OFF - CHARGING
COMPLETE
NOTE: Only Audiovox
approved rechargeable
battery (Model GMRS5BAT)
can be recharged in the
radio transceiver.
8
128-7627
8 of 28
Charging Indications
When either, or both, units are being charged in the charging stand, the
associated red LED charging indicator will light steadily. In addition, the
AC wall adapter LED will also light steadily. When fully charged, the
LEDs will be off.
GMRS762CH Operational Modes
Controls:
LED Flashlight Enable Button (2)
When the unit is on, press this button on the left side of the Transceiver to light the white flashlight LED (10) on top of the unit.
Power On-Off/SCAN (8) Button
Press and hold the power on/off button ( s ) for at least 2 seconds.
You will hear a confirming melody to indicate the unit is on. To turn the
unit off, press and hold the button for at least 2 seconds. When the unit
is on, press this button momentarily to enable or disable the scan
mode.
Adjusting the Volume (13, 15)
With the unit powered on, press the Up Channel/Volume button (S) to
increase volume and the Down Channel/Volume button (T) to decrease
volume. The display will indicate the current volume level between 0 to 7
bars on the right lower side of the LCD.
9
128-7627
9 of 28
Monitor/Display Backlight Button (14)
This button is used to check activity on the current frequency before
transmitting. Check activity by pressing the Monitor (M) Button longer
icon will appear on the display and you will hear
than 2 seconds; the
static if frequency is clear. Do not transmit if you hear conversation.
Hold down the Monitor Button again longer than 2 seconds and the
icon will disappear from the display.
The monitor function will temporarily bypass the squelch setting and
play all signals on a given channel. This feature is useful when communicating with other parties at extreme range.
By pressing the monitor button momentarily, the LCD backlight is turned
on accompanied by a beep tone (if enabled); the LCD backlight will turn
off automatically in about 5 seconds, or when the monitor button is pressed
momentarily once again.
Push To Talk (PTT) Button (3)
Pressing and holding this button will allow you to speak to any transceiver that is set to the same channel and privacy code setting as yours.
Hold the transceiver approximately 1 to 2 inches from your face as you
speak into the built in microphone (7). After you have finished speaking,
release the PTT Button to allow reception of incoming signals. It is not
possible to transmit and receive at the same time. The Transmit Signal
) will display the relative strength of the transmitted
Level indicator (
) icon will appear in
signal. When receiving an incoming signal, the (
the upper right quadrant of the display. The PTT button can also be used
as a two-way
10
128-7627
10 of 28
call ringer. Pressing the button twice quickly will call another party on the
same channel.
Up Channel/Volume Button (15)
In the standby mode, pressing this button increases the listening volume.
When in function edit mode this button is used to adjust the unit’s settings.
Down Channel/Volume Button (13)
In the standby mode, pressing this button decreases the listening
volume. When in function edit mode this button is used to adjust the
unit’s settings.
Mode Button (6)
This button is used to select the various feature settings in the GMRS/
FRS or FM radio band modes. Holding the MODE button longer than 2
seconds will toggle between the GMRS/FRS and FM band modes.
External Microphone (MIC)/Speaker (SPK)/(CHG) Jack (11)
This jack accepts an Audiovox Earbud/microphone connector, or the
Charging Adapter connector. For equipment and accessories supplied
with the GMRS762CH, refer to Page 7 and/or visit the Audiovox web site
at www.audiovox.com.
VOX/LOCK Button (5)
Press this button momentarily to enable or disable the VOX mode; the
icon will appear in the middle right side of the display when VOX is enabled. Press and hold the button for more than 2 seconds to enable or
disable the LOCK mode; the keylock icon ( ) will appear to disable the
MODE, SCAN and channel up/down buttons.
11
128-7627
11 of 28
Operating Modes and Features
GMRS Operation:
- From GMRS/FRS standby mode, press and hold the ( s ) button
for at least 2 seconds to turn on power.
- Press the MODE button so the Channel number flashes.
- Select the desired channel with the Up (15) and Down (13) But
icon appears to indicate the
tons. When receiving a call, the
incoming signal.
- Press and hold the PTT button (3) to transmit, then speak into
themicrophone clearly and slowly. The Transmit Signal indicator
) appears on the display.
(
NOTE: When the transmission is not available with beep tone, the
battery is low; recharge the unit.
When the battery icon is flashing, transmitting is not possible;
recharge the unit.
- Release PTT Button (3) to receive.
- Communication can only be accomplished when the channel and
CTCSS tone frequency of at least two parties are the same.
- The CTCSS small segment display will appear next to the main
frequency channel on the display if the CTCSS tone frequency
function is enabled.
Channel Selection
In order to communicate with other GMRS units, both transmitting and
receiving party must be on the same frequency. The GMRS762CH has
22 channels (frequencies) indicated by the large digits on the LCD display panel. Channels 1 through 7 are the shared GMRS/FRS channels.
Channels 8-14 are FRS only channels, while channels 15-22 are assigned
GMRS only channels. If an FRS only channel (8-14) has been selected,
12
128-7627
12 of 28
the HI or LO indicator will not be displayed on the LCD panel; otherwise,
for channels 1-7 (GMRS/FRS) and 15-22 (GMRS only), the HI or LO indicator will be displayed. Communication with Audiovox FRS and compatible units is possible on the shared and FRS only channels. Before transmitting on the selected channel, press the Monitor (M) Button (2) to check
the activity on that channel. If there is activity on the selected channel,
change to another channel that is clear.
To change the channel:
- From GMRS/FRS standby mode, press the MODE button (6)
once or until the channel number flashes.
- Press the Up Button (15) briefly to move to the next higher main
channel number.
- Press the Down Button (13) briefly to move to the next lower main
channel number.
- Press the PTT button momentarily to confirm selection.
CTCSS Mode (Sub-Channel) Selection
The Coded Tone Controlled Squelch System (CTCSS) provides 38 SubFrequencies. This feature allows you to utilize the coded squelch tones
(01–38) within a main channel, and enables you to communicate with
another party on the same main channel using the same subcode. (This
filters out unwanted transmissions without the same coded squelch tone).
There are 38 CTCSS Sub-channels for each main channel. A different
subcode may be selected for each of the 22 channels.
To change the CTCSS Sub-channel:
- From GMRS/FRS standby mode, press the MODE Button twice; a
flashing oF or sub-channel number is displayed. If oF is displayed,
press the Up or Down button to enable the CTCSS mode.
- Then press the Up or Down button to select the desired sub-channel for use (01-38).
- Press the PTT button momentarily to confirm selection.
13
128-7627
13 of 28
The CTCSS mode can be turned off by selecting the oF icon as the setting.
NOTE: To communicate with other GMRS/FRS units, they must be
switched to the same channel and CTCSS subcode. To communicate with other GMRS/FRS units that do not have subcodes,
switch your unit to the same channel with the subcode set to oF.
The CTCSS subcodes do not prevent others from hearing your
transmission. This will only allow you to ignore all traffic on a
given channel not using the same subcode.
Transmit Power Selection Mode
This feature permits selection of the transmitting power level to high
or low. When operating on FRS only channels (8-14), no power selection
is possible or is displayed. Using low power, the unit will have a lower
transmit range, but battery life will be increased.
To access the transmitter power selection function:
- From GMRS/FRS standby mode (shared channels 1-7 or GMRS
only channel (15-22) selected), press the MODE Button three times
until the power HI or LO indication appears with a flashing Pr indication on the display.
- Press the Up or Down button to toggle between the High and Low
selections.
- Press the PTT button momentarily to confirm selection.
VOX Sensitivity Level Selection
This selection enables you to set the sensitivity level to compensate for
ambient noise in your immediate area. A VOX sensitivity of 2 represents
high sensitivity, and should be used in a relatively quiet surrounding.
A VOX sensitivity of 1 represents low sensitivity and should be used in
a noisy environment.
To set the VOX sensitivity level:
14
128-7627
14 of 28
- Press the MODE button 4 times (3 times for FRS) until the Vo icon
appears on the display accompanied by the flashing numeral 1 or
2.
- Press the Up or Down button to select the 1 or 2 VOX level
sensitivity.
- Press the PTT button momentarily to confirm the VOX selection.
- The
icon only appears when the VOX mode is enabled.
Dual Watch Mode
This feature allows you to monitor two channels at the same time.
While in dual watch mode, the unit will continuously monitor both the
primary and dual watch channel. Received signals will be played for 5
seconds, then the unit will resume scanning the two channels. Pressing
the PTT button during a received transmission will set the unit to
transmit on the same channel. Pressing the PTT button when no signal
is received will set the unit to transmit on the primary channel.
To set the Dual Watch Mode:
- From GMRS/FRS standby mode, press the MODE button 5 times
(4 times for FRS);
appears flashing on the display. If the dual
watch mode is off, the oF icon will also appear flashing.
- To enable the dual watch mode, press the Up or Down button; the
dual watch channel number will flash and start to increase or
decrease as the Up or Down button is pressed.
- To select a subcode for the dual watch channel, press the MODE
button while the selected dual watch channel is flashing. Then use
the Up and Down buttons to select the desired CTCSS subcode.
- Press the PTT button momentarily to confirm selection of the dual
watch channel. The display will now alternate between the primary
channel and the dual watch channel just selected.
15
128-7627
15 of 28
NOTE: Pressing the PTT button during dual watch mode will transmit
on the primary channel and suspend dual watch operation for
5 seconds. Dual watch mode will then resume.
- Momentarily press the SCAN button to exit the dual watch mode.
Key Tone
This feature allows the transceiver to sound a confirmation tone whenever the following keys are pressed: Monitor (M) Button, Up/Down Buttons, MODE Button or SCAN Button.
To turn the key tones on or off:
- From GMRS/FRS standby mode, press the MODE Button 6 times
(5 times for FRS) until the Bell ( ) icon flashes, and on or oF appears on the display.
- Press the Up or Down Button to toggle the key tone feature On or
Off.
- Press the PTT button momentarily to confirm selection.
When the key tone feature is on, the Bell icon appears steady on the
display, and the beep tones sound in response to button activation.
Roger Beep Tone
The Roger Beep is a tone which is automatically transmitted whenever
the PTT button is released. This tone alerts the receiving party that the
transmission has been terminated intentionally.
To enable and disable the Roger Beep tone:
- From GMRS/FRS standby mode, press the MODE Button 7 times
) and on
(6 times for FRS) until the flashing Roger Beep icon (
or oF appears on the display.
- Press the Up or Down button to select the tone on or off as desired.
) appears steady on the display.
- When enabled, the tone icon (
- Press the PTT button momentarily to confirm selection.
16
128-7627
16 of 28
Call Ringer Selection Mode
The transceiver provides 3 user-selectable call ringer melodies to alert
you to an incoming call.
To select your favorite call ringer melody:
- From GMRS/FRS standby mode, press the MODE Button 8 times
(7 times for FRS). CA will appear on the display, together with a
flashing number between 1 and 3, and an appropriate call ring.
- Press the Up or Down Button to preview and hear the 3 available
call melodies.
- Press the PTT button momentarily to confirm selection.
Channel Scan Operation
This feature allows you to monitor all channels automatically for valid
signals. While scanning, you can transmit and receive. When a signal is
received, the scan is interrupted and will return to scan mode 5 seconds
after reception is terminated.
NOTE: While the scan function is active, the MODE button will be
inoperative. The scan mode will reduce overall battery life since
the battery save function is overridden.
To enable the channel scan mode:
- From GMRS/FRS standby mode, momentarily press the power Button; ( ) will appear on the LCD display.
- The radio will display each channel (1-22) in ascending order as the
scan mode operates to find an active main channel.
- If the unit doesn’t find any signals and you want to transmit, press
the PTT button to return to home channel operation. The channel
number will flash and the transceiver will then automatically resume
scanning approximately 15 seconds after the communication is completed.
17
128-7627
17 of 28
- If there is no activity and you want to leave the scan mode, press
the power button momentarily and the unit will return to normal opicon will disappear from the LCD display.
eration; the
Auto Key Lock Selection Mode
This feature prevents accidental changes to the preferred settings of the
unit. The Auto Key Lock function temporarily disables the MODE, Up/
Down and SCAN Buttons.
To access the Auto Key Lock selection menu:
- From GMRS/FRS standby mode, press and hold the VOX Button
for 2 seconds to enable the Auto Key lock function; the unit will
beep once and the lock ( ) icon appears on the display.
- The Power and PTT Buttons are not effected.
- To unlock the Auto Key function, press and hold the VOX button for
2 seconds; the unit beeps once and the lock icon ( ) disappears
from the display.
NOTE: If the unit is turned off while Key Lock is on, the Key Lock
mode will still be in effect when the unit is again turned on.
VOX Enable Operation
This option enables you to have hands-free conversation. Your voice or
nearby sound is detected and the radio transmits without the need to
press the PTT button.
To enable VOX operation:
- From GMRS/FRS standby mode, press the VOX button momenicon appears steady on the display.
tarily; the
- To disable the VOX mode, press the VOX button momentarily;
the VOX icon disappears from the display.
18
128-7627
18 of 28
Battery Alert
When the battery icon (
) flashes on the display, 5 minutes later the
unit will turn off automatically. When this occurs, recharge the unit.
NOTES FOR GOOD COMMUNICATION
1. The GMRS762CH 22 channels are shared on a ‘take turns’ basis.
This means other groups may be talking on any of the channels.
A common code of ethics/courtesy is to switch to another vacant
channel and not to attempt to talk over someone who is already
using the channel you first selected.
2. The GMRS762CH has been designed to maximize performance
and improve transmission range in the field. To avoid interference,
it is recommended that you do not use the units closer than 5 feet
apart.
3. For best transmission results, always keep your mouth about 2-3
inches from the microphone (9) and speak slowly in a normal voice.
4. To increase battery life, avoid features such as Scan and Dual
Watch. These features will reduce operating time considerably.
19
128-7627
19 of 28
Warning
• Do not operate the transceiver unless you are licensed to do so.
• Remove the batteries from the transceiver if it is not expected to be
used for long periods. This will eliminate the possibility of chemicals
leaking from the batteries and corroding the transceiver.
• Avoid exposing the transceiver to water or extremes of temperature.
• Do not use this device in or near a mining facility, which uses
remotely triggered explosives or in areas labeled “Blasting Area”.
Premature or accidental detonation may result.
• Do not attempt to modify or in any way increase the output of this
transceiver. Its output is designed to meet the legal limits set by the
FCC.
• Do not use this device or change its batteries in potentially explosive
atmospheres as sparks in such areas could result in an explosion.
• Turn your transceiver off wherever posted notices restrict the use of
radios or cellular telephones. Facilities such as hospitals may use
equipment that is sensitive to RF energy.
20
128-7627
20 of 28
• Turn your transceiver off on board aircraft when requested to do so.
• Do not place your radio in front of a vehicle’s air-bag. If the air-bag
deploys, it could propel the transceiver like a projectile causing
bodily injury.
Troubleshooting
Problem
Possible cause
Correction
No transmission
while pressing
the PTT Button
Weak batteries
Charge or replace batteries
Weak or no
signal received
Weak batteries
Channel and privacy
code not set the same
as target transceiver
Charge or replace batteries
Adjust the transceiver’s
settings to match those
settings of the target
transceiver
Increase volume level
Release PTT Button
Volume level too low
PTT Button inadvertently
depressed
Excessive radio interference
on a particular channel
Obstruction of radio signal
Unit beeps, but
will not function
when turned on
Reception of
unwanted signals
Batteries extremely
discharged
CTCSS privacy mode
not on
Interference from
electronic devices such
as computers or TVs
Change to a different
channel
Avoid operating in or near
large buildings or vehicles
Charge or replace batteries
Turn on the CTCSS privacy
mode and set code number
to match the setting of the
target transceiver.
Turn the devices off or move
farther away from them.
21
128-7627
21 of 28
Technical Specifications:
General
Frequency Range:
Channels 1-7 (Shared with
FRS Radios)
Channels 8-14 (FRS only)
Channels 15-22 (GMRS only)
Channel Spacing
Privacy Codes
Dimensions (W x H x D)
(Without Antenna)
Refer to frequency chart on next page
Refer to frequency chart on next page
Refer to frequency chart on next page
12.5 kHz
38 for each main channel
2.15 in x 3.5 in x 0.52 in
54.5 mm x 89 mm x 13.1 mm
Power Supply
Power Source
Li-ion, 3.7 VDC, 720 mAh
Operating Time:
26 Hours Low Power
(Transmit: Receive: Standby 10 Hours High Power
(5:5:90 Ratio)
Receiver
Usable Sensitivity
>-119 dBm
Maximum Audio Output Power > 0.3 Watt maximum (16 Ohm )
Modulation Distortion
< 5% (1 kHz 70%)
Transmitter
RF Output Power
(Conducted)
Maximum Deviation
Modulation Distortion
1.8 Watts maximum (High Power)
0.5 Watt maximum (Low Power)
<+/- 2.5 kHz
< 5% (1 kHz 70%)
22
128-7627
22 of 28
FM radio Band
87.5 - 107.9 MHz
This transceiver complies with FCC regulations for use in the United
States of America. Use in other countries may be prohibited or restricted
by local regulation. Please check with the local regulating agency before using this device outside the United States of America.
Main Channel Frequencies:
CHANNEL /TYPE
FREQ (MHz )
CHANNEL /TYPE
FREQ (MHz )
1
GMRS/FRS
462.5625
12
FRS
467.6625
2
GMRS/FRS
462.5875
13
FRS
467.6875
3
GMRS/FRS
462.6125
14
FRS
467.7125
4
GMRS/FRS
462.6375
15
GMRS
462.5500
5
GMRS/FRS
462.6625
16
GMRS
462.5750
6
GMRS/FRS
462.6875
17
GMRS
462.6000
7
GMRS/FRS
462.7125
18
GMRS
462.6250
8
FRS
467.5625
19
GMRS
462.6500
9
FRS
467.5875
20
GMRS
462.6750
10 FRS
467.6125
21
GMRS
462.7000
11 FRS
467.6375
22
GMRS
462.7250
NOTE: Channels 1 through 7 are shared with FRS radios.
Channels 8 through 14 are FRS only.
Channels 15 through 22 are GMRS only.
23
128-7627
23 of 28
CHANNEL CROSS REFERENCE FOR 14 AND 15 CHANNEL GMRS/
FRS RADIO TO 22 CHANNEL GMRS/FRS RADIO
CHANNEL CROSS REFERENCE
FOR 15 CHANNEL GMRS/FRS
RADIO TO 22 CHANNEL
GMRS/FRS RADIO
15 C H A N N E L
GMRS
CHANNEL CROSS REFERENCE
FOR 14 CHANNEL FRS
RADIO TO 22 CHANNEL
GMRS/FRS RADIO
22 C H A N N E L
FRS/GMRS
14 C H A N N E L
FR S
22 C H A N N E L
FRS/GMRS
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
8
8
8
9
9
9
10
10
10
11
11
11
12
12
12
13
13
13
14
14
14
CHANNELS
NOT
AVAILABLE
CHANNELS
NOT
AVAILABLE
CHANNELS NOT AVAILABLE
1
15
11
15
8
16
12
17
9
18
13
19
10
20
14
21
15
22
16
17
18
19
20
21
22
NOTE
WHEN USING RADIOS PRODUCED BY OTHER MANUFACTURERS,
COMPARE CHANNEL FREQUENCIES FOR COMPATIBILITY.
24
128-7627
24 of 28
Continuous Tone Coded Squelch System Tone
Frequencies (in Hz)
CTCSS
Freq. Hz
CTCSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Freq. Hz
131.8
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
* oF = No Tone
25
128-7627
25 of 28
THIS PAGE LEFT BLANK INTENTIONALLY
26
128-7627
26 of 28
90 DAY LIMITED WARRANTY
Applies to Audiovox Family Radio and General Mobile Service Products.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this
product that should this product or any part thereof, under normal use and conditions, be proven
defective in material or workmanship within 90 days from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option)
without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered
with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation
prepaid, to the warranty center at the address shown below.
The Company disclaims liability for communications range of this product.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company,
has suffered or been damaged through alteration, improper installation, mishandling, misuse,
neglect, accident, or by removal or defacement of the factory serial number/bar code label(s).
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO
THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE
COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED
TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume
for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damage so the above limitations or exclusions may not
apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
AUDIOVOX ELECTRONICS CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788
1-800-290-6650
128-5385B
27
128-7627
27 of 28
© 2005 Audiovox Electronics Corp., Hauppauge, NY 11788
Printed in China
128-7627
28
128-7627
28 of 28