PowerForce® Turbo
B A G L E S S
USER’S GUIDE
6596 SERIES
3
Safety Instructions
4
Product View
5-6 Assembly Instructions
6-7 Operation / Special Tools
8-11 Maintenance
12-13 Troubleshooting
14
15
16
ug203-2829_6596_1105.indd 1
Replacement Parts
Consumer Services
Warranty
1/11/06 4:03:29 PM
Thanks For Buying A BISSELL PowerForce® Turbo Bagless
We’re glad you purchased a BISSELL PowerForce Turbo Bagless Vacuum.
Everything we know about floor care went into the design and construction of
this complete, high-tech home vacuuming system.
Your BISSELL PowerForce Turbo Bagless is well made, and we back it with
a limited comprehensive one-year warranty. We also stand behind it with a
knowledgeable, dedicated Consumer Services Department, so, should you ever
have a problem, you’ll receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a
global leader in the design, manufacture, and service of high quality homecare
products like your BISSELL PowerForce Turbo Bagless.
Thanks again, from all of us at BISSELL.
Mark J. Bissell
President and Chief Executive Officer
2
ug203-2829_6596_1105.indd 2
1/11/06 4:03:33 PM
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING YOUR
UPRIGHT VACUUM.
Always connect to a polarized outlet (left slot is
wider than right). Unplug from outlet when not in
use and before conducting maintenance.
WARNING:
To reduce
the risk of fire, electric shock,
or injury:
■ Do not modify the polarized plug to fit a
■
■
■
■
■
■
■
■
■
■
■
■
■
■
non-polarized outlet or extension cord.
Do not leave vacuum cleaner unattended
when it is plugged in.
Unplug from outlet when not in use and
before servicing.
Do not use outdoors or on wet surfaces.
Do not allow children to operate vacuum
cleaner or use as a toy.
Close attention is necessary when used by or
near children.
Do not use for any purpose other than described
in this User’s Guide.
Use only manufacturer’s recommended
attachments.
Do not use with damaged cord or plug.
If appliance is not working as it should,
has been dropped, damaged, left outdoors,
or dropped into water, have it repaired at an
authorized service center.
Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run
appliance over cord. Keep cord away from
heated surfaces.
Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
Do not handle vacuum cleaner or plug with
wet hands.
Do not put any object into openings.
Do not use with any opening blocked; keep
openings free of dust, lint, hair, and anything
that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
■ Turn off all controls before plugging or
unplugging vacuum cleaner.
■ Use extra care when cleaning stairs.
■ Unplug before attaching the TurboBrush.
■ Do not pick up flammable materials (lighter
■
■
■
■
■
■
■
■
fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapors.
Do not pick up toxic material (chlorine bleach,
ammonia, drain cleaner, etc.).
Do not use vacuum cleaner in an enclosed
space filled with vapors given off by oil base
paint, paint thinner, some moth proofing
substances, flammable dust, or other
explosive or toxic vapors.
Do not pick up hard or sharp objects such as
glass, nails, screws, coins, etc.
Do not pick up anything that is burning
or smoking, such as cigarettes, matches, or
hot ashes.
Do not use without filters in place.
Use only on dry, indoor surfaces.
Keep appliance on a level surface.
Do not carry the vacuum cleaner while it
is running.
SAVE THESE
INSTRUCTIONS FOR
FUTURE USE
THIS APPLIANCE HAS
A POLARIZED PLUG.
To reduce the risk of electric shock, this appliance has
a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the
plug. If it still does not fit, contact a qualified electrician
to install a proper outlet. Do not change the plug in
any way.
This model is for household use only.
3
ug203-2829_6596_1105.indd 3
1/11/06 4:03:34 PM
Cord Clip
Hose Clip
Handle
Stretch Hose
TurboBrush®
Bracket
Crevice Tool
TurboBrush®
Carrying
Handle
Extension Wand
Quick Release
Cord Wrap
Louvers
Quick Reach®
Handle
Hose Wand
Combination
Dusting Brush/
Upholstery Tool
Hose
Wand Base
Power Cord
Upper Tank
Power Switch
Handle
Release
Pedal
Dirt Container
Filter Cup
Washable Inner and
Outer Circular Filters
Lock ’n Seal™
Lever
Foot Hose
Headlight
HEPA Post-Motor Filter
Height
Adjustment
Knob
Powerfoot
Furniture Protection
Guard
CAUTION:
Do not plug in your vacuum
4
ug203-2829_6596_1105.indd 4
cleaner until you are familiar
with all instructions and
operating procedures.
1/11/06 4:03:34 PM
How To Use This Guide
This User’s Guide has been designed to help you
get the most satisfaction from your BISSELL PowerForce
Turbo Bagless. You’ll find assembly and operating
instructions, safety precautions, as well as maintenance
and troubleshooting instructions. Please read this Guide
thoroughly before assembling your vacuum cleaner.
Pay particular attention to the product diagram,
assembly instructions, and part names. Locate and
organize all parts before assembly. Familiarize
yourself with the parts and where they fit. Following
this User’s Guide will greatly enhance your ability
to get the most performance from your BISSELL
PowerForce Turbo Bagless for many years.
WARNING:
Plastic film can be
dangerous. To avoid
danger of suffocation,
keep away from
babies and children.
How To Put It Together
The only tool you’ll need to assemble your vacuum
cleaner is a screwdriver.
Attach Handle To Vacuum
1. Locate the vacuum Handle and remove the screw
packet taped to the base of the Handle.
Stand the vacuum upright and place the Handle on the
2. top of the vacuum body as shown.
Insert the screws provided from the screw packet into
3. the existing holes on each side. Tighten securely with
a screwdriver.
Attach Vacuum Hose and Tools
™
1. Attach the Twist ‘n Snap Hose by lining up the tabs on
the base with the corresponding notches on the back of
the vacuum as shown.
2. Turn the Twist ‘n Snap Hose to the right to lock the hose
into place.
3. Grasping the Quick Reach Handle, slide the end of the
Hose Wand onto the Hose Wand Base. Snap the Hose
into the Hose Clip.
NOTE: The Powerfoot will not operate
effectively unless the Hose Wand is
firmly attached.
4. Slide the Extension Wand and the Crevice Tool together
into the storage clip on the side of the vacuum.
5. Snap the Combination Tool into the storage clip on the back of
the vacuum.
®
6. The TurboBrush Bracket slides onto the front of the Handle.
Attach the Bracket by aligning the pegs with the holes on the
Handle as shown and pulling down until it is locked into place.
ug203-2829_6596_1105.indd 5
5
1/11/06 4:03:35 PM
Attach Vacuum Hose and Tools Continued
7. Place the TurboBrush in the Bracket by aligning the
bottom of bracket with the opening of the brush roll
and snap the TurboBrush into place.
How To Use Your Vacuum
Handle Positions
Press the Handle Release Pedal with your foot to place
your vacuum in one of three cleaning positions.
1. Upright- For storage and above floor cleaning with tools.
2. Normal Cleaning- Press Handle Release Pedal once.
Use for most household floor cleaning tasks.
3. Low Cleaning- With the vacuum in normal cleaning position,
press Handle Release Pedal again. Use for reaching under
low furniture such as tables, chairs or beds.
Height Adjustment
CAUTION:
Before using your vacuum,
The Powerfoot/Rotating Floor Brush can be
adjusted to clean several floor surfaces.
make sure that the Dirt
Container is in locked
position and that all filters
(Inner Circular, Outer Circular,
Pre-Motor and Post-Motor) are
in place. Do not operate your
vacuum without these filters.
NOTE: For optimal cleaning performance,
adjust to the lowest practical setting. If
your cleaner is difficult to push, adjust to
the next higher setting.
1. Place Handle in Upright Position.
Tip:
2. Turn Height Adjustment Knob to desired setting.
Lowest Setting For bare floors.
Medium Settings For short and medium
pile carpets.
Highest Setting For plush pile carpet.
3. Place the Handle in the normal cleaning position and
the Powerfoot will adjust to the setting chosen.
NOTE: You may also adjust the setting
while in the normal cleaning position.
Transporting Cleaner
1. To move your cleaner from room to room, put the
Handle in the upright position, tilt the cleaner back on
its rear wheels and push forward.
2. The cleaner can also be moved by using the Carrying
Handle on the back.
5
Before cleaning under
low furniture, check
area first for objects
that might harm the
unit or block the
Vacuum Hose.
Tip:
Your vacuum features
a Quick Release Cord
Wrap. To remove the
Power Cord quickly
and easily, rotate the
Upper Cord Wrap
towards floor, and
slip Power Cord from
Upper and Lower
Cord Wraps.
Carrying Handle
6
ug203-2829_6596_1105.indd 6
1/11/06 4:03:36 PM
Special On-Board Tools
Your BISSELL PowerForce Turbo Bagless is not
only a powerful carpet and rug vacuum cleaner,
it’s also a versatile above floor vacuum cleaner
when you select one of the special tools.
NOTICE:
The Floor Brush will continue to rotate
while you use your vacuum for above
floor cleaning. To prevent carpet
damage, do not lean on the vacuum
or let the Powerfoot tilt forward.
1. Raise Handle to Upright Position.
2. Grasp the Quick Reach Handle and lift Hose Wand to
separate from suction intake opening.
3. Attach tools by firmly pushing onto Vacuum Hose or
Extension Wand.
Combination Dusting Brush/Upholstery Tool:
Two types of cleaning tools are included in one attachment:
rotate for desired tool.
■ Use Brush side to dust furniture, blinds, books,
lamps, shelves, and baseboards.
■ Use Upholstery side for curtains,
draperies, cushions, fabrics.
Crevice Tool:
Use in tight narrow spaces.
Extension Wand:
Use with desired attachment for a
longer reach.
Tip:
TurboBrush: Use rotating brush action
for small areas such as stairs and upholstery.
Note: Press gently when using the
TurboBrush to gain maximum
cleaning. Too much pressure will
cause the brush to stop rotating.
Hair, string and small
objects can block
the Vacuum Hose
or Tools. Check
them occasionally for
obstructions.
Power Cord Storage
When you are done using your vacuum,
return it to the Upright position and store
the Power Cord.
1. Turn vacuum cleaner off.
2. Unplug Power Cord by grasping the polarized
plug (NOT the cord) and disconnect from outlet.
3. Loop Power Cord around Cord Wraps on side of
vacuum cleaner.
4. Clip molded plug to Power Cord to secure.
CAUTION:
The Rotating Floor Brush continues to
rotate while tools are in use. To reduce the
risk of injury from moving parts, always
move the cleaner with the Carrying Handle
at the back of the cleaner. Always place
vacuum cleaner on floor with Handle in
Upright position when using tools. Never
place your fingers under the cleaner when
it is running. Never place Powerfoot on
furniture or uneven surfaces. Do not place
vacuum cleaner close enough to objects to
pull them into rotating brush.
NOTICE:
While vacuuming, certain carpets
and low humidity conditions may
generate small static discharges.
The discharges are entirely
harmless and are not associated
in any way with the main
power supply.
7
ug203-2829_6596_1105.indd 7
1/11/06 4:03:37 PM
How To Maintain Your Vacuum
To maintain maximum cleaning performance, the
following maintenance steps must be performed:
WARNING:
1. Empty the Dirt Container when the dirt reaches the
To reduce the risk of
electric shock, turn
Power Switch OFF and
disconnect polarized
plug from electrical outlet
before performing
maintenance or
troubleshooting checks.
“Full” line on the side.
2. Check the Inner and Outer Circular Filters, and the
Pre-Motor Filter at least once a month and clean or
replace as needed.
3. Replace the HEPA Post-Motor Filter every three to
six months.
Note: More frequent filter cleaning or
replacing may be necessary if you are
vacuuming new carpet, fine dust, or have
allergy concerns. Follow the instructions on
the following pages to perform these simple
maintenance steps.
Tip:
For maximum cleaning
performance, check
and clean or replace all
filters as suggested.
Empty Dirt Container
Full Line
The Dirt Container needs to be emptied when the dirt
reaches the “Full” line on the side of the Container.
1. Unplug cleaner from electrical outlet.
2. Slide the Lock ‘n Seal Lever to the "Unlock" position.
Unlock
Position
Lock Position
3. Grasp handle and pull the Dirt Container straight out to
remove from vacuum.
4. Empty dirt into garbage container.
5. Put the Dirt Container back in the vacuum and slide the
lever to the "Lock" position.
Note: The Dirt Container may be washed in
warm water with a mild detergent. Remove
the Filter Cup from the bottom before
washing. Reassemble and make sure it is
completely dry before using again.
Cleaning The Inner & Outer Circular Filters
Use only BISSELL Style 12 Replacement Filters in
your BISSELL PowerForce Turbo Bagless.
1. Unplug the cleaner from electrical outlet.
2. Remove the Dirt Container as described in the previous
section. Grasp the Filter Cup located at the bottom of
the Dirt Container and twist counterclockwise to unlock
and remove.
3. Grasp the Circular Filters and twist to unlock. Pull
straight up to remove.
4. Separate the Outer foam and Inner pleated Circular
Filters. Wash each individually by hand in warm water.
Mild detergent may be used if desired. Rinse well, then
air dry thoroughly before putting them back together
and replacing in Filter Cup.
8
ug203-2829_6596_1105.indd 8
1/11/06 4:03:37 PM
Cleaning The Inner & Outer Circular Filters continued
5. The Filter Cup may be washed in warm water with a
mild detergent. Make sure it is completely dry before
reassembling with filters.
6. The Upper Tank and Louvers may also be wiped clean
with a damp cloth. Reach underneath the Upper Tank
and turn the rim of the Louvers to unlock. Pull straight
down to remove.
Cleaning Pre-Motor Filter
WARNING:
Do not operate cleaner
1. Unplug the cleaner from electrical outlet.
2. The Pre-Motor Filter protects the motor from debris. It is
located underneath the Dirt Container and Filter Cup in
the center of the round part of the Lock ‘n Seal Lever.
with damp or wet
filters or without all
filters in place.
3. Remove the small round Filter and any debris on top of
it. Rinse well under warm water, then air dry thoroughly
before replacing.
Pre-Motor
Filter
Replacing the HEPA Post-Motor Filter
Use only BISSELL Style 12 HEPA Filters (#3205) in
your BISSELL PowerForce Turbo Bagless.
1. Unplug the cleaner from electrical outlet.
2. The HEPA Post-Motor Filter assists in the filtration process
to return clean air to the room. It is located behind the door
on the front of the cleaner. When the filter becomes dirty,
open the door, remove the filter and replace.
Note: This filter is not washable and must
be replaced.
3. Replace the door by inserting the tabs on the left side
and snapping the right side into place.
Maintaining TurboBrush
HEPA
Post-Motor
Filter
WARNING:
To reduce the risk of
injury from moving parts,
turn off vacuum cleaner
and disconnect Power
Plug from electrical outlet.
The TurboBrush should be checked regularly for
clogs or debris wrapping around the brush roll.
1. Unplug vacuum from electrical outlet.
2. If a clog is present or debris is visible, unscrew the two
screws on the back of the TurboBrush to remove the
faceplate and clear any obstructions.
3. To clean debris from the brush roll, remove the screw
located by the brush roll with a Phillips head screwdriver. Lift the belt cover. Remove the brush roll from
the drive belt and clean debris.
4. Reposition the drive belt on the brush roll. Place ends
of brush roll in slots on sides as shown. Reposition belt
cover and secure with one screw. Reposition faceplate
and secure with two screws.
9
ug203-2829_6596_1105.indd 9
1/11/06 4:03:38 PM
Check Rotating Floor Brush and Drive Belt
You should check your vacuum cleaner’s Rotating
Floor Brush and Drive Belt regularly for wear or
damage. You should also clean the brush and brush
ends of strings, hair, and carpet fibers. These can
wrap around the brush and hamper its ability to
effectively clean your carpet. Also remove any debris
that has accumulated under the brush cover.
4
1. Unplug cleaner from electrical outlet.
2. Place handle in Low position and turn vacuum cleaner over
so bottom side is up.
3. Lift tab 1 and release the three latches in order 2-4 as
marked. Lift the Brush Cover off.
4. Grasp Rotating Floor Brush at both ends and lift.
Motor Pulley
5. Clean strings, hair and other debris from Rotating Floor
Brush, paying particular attention to brush ends.
6. Clean strings, hair and other debris from Motor Pulley and
Drive Belt areas.
7. Check Drive Belt carefully for wear, cuts or stressed areas.
8. Check Air Passageway for obstructions. Remove debris
from this area.
Air Passageway
Replace Drive Belt
Use only BISSELL Style 12 Replacement Belts (#32074)
in your BISSELL PowerForce Turbo Bagless.
1. Unplug cleaner from electrical outlet.
2. With Rotating Floor Brush removed from vacuum cleaner
(Steps 1-4 of Check Rotating Floor Brush and Drive Belt),
grasp old Drive Belt and remove from Motor Pulley. Discard
old Drive Belt.
3. Place new Drive Belt over Motor Pulley and stretch other
end over Rotating Floor Brush in the space between
the bristles.
4. Place ends of Rotating Floor Brush down into slots on sides
as shown.
5. Turn Rotating Floor Brush by hand several times in the
direction of Motor Pulley. If properly installed, Drive Belt will
center itself on Rotating Brush.
6. Reposition Brush Cover and snap back into place. Check to
be sure all three latches are secured.
10
ug203-2829_6596_1105.indd 10
1/11/06 4:03:39 PM
Replace Lightbulb
Use only BISSELL Replacement Bulbs in your BISSELL
PowerForce Turbo Bagless.
1. Unplug cleaner from electrical outlet
2. Using a flat screwdriver, table knife or coin, insert into the
slot on the right of the lens and gently push inner latch to
the left as shown to remove the lens.
3. Remove the bulb from the socket by grasping bulb and
pulling straight out. Install the new bulb by pushing it
gently into the socket until the bulb snaps into place.
4. Reposition lens, by inserting tab on left side and then
pushing the right side back into place.
Clearing Clogs
Low suction, poor pickup, or no suction may be due to
a clog in the vacuum cleaner. If you notice a change in
the sound of the motor or a reduction in the spinning
action in the Dirt Container, check for clogs.
1. Unplug cleaner from electrical outlet.
Louvers
2. Empty Dirt Container.
3. Check Upper Tank and Louvers for build up or clogs.
Check to make sure Louvers are installed correctly. To
unlock the Louvers, grasp the rim and turn toward the left.
Pull straight down to remove. If the Louvers are missing
or not locked into place, check and clear the tube in the
center of the Dirt Container.
Suction
Inlet
4. Remove the Twist ‘n Snap Hose from the vacuum by
turning to the left. Check the Suction Inlet, Hose and Hose
Wand for clogs. Remove any clogs from the hose using a
long, narrow object.
5. Check the Foot Hose for clogs. If needed, remove the screw
attaching the Hose Wand Base to the vacuum. Straighten
the Foot Hose and unclog with a long, narrow object.
6. If the clog persists, follow the instructions for Checking
the Rotating Floor Brush on page 10 and inspect the Air
Passageway for obstructions.
Hose
Wand Base
Air Passageway
ug203-2829_6596_1105.indd 11
11
1/11/06 4:03:40 PM
Troubleshooting
WARNING:
To reduce the risk of injury
from moving parts and/
or electrical shock, turn
Power Switch OFF and
disconnect polarized plug
from electrical outlet
before performing
troubleshooting checks.
Vacuum cleaner won’t run
Possible Causes
1
2
Power cord not plugged in
Blown fuse/tripped breaker
Remedies
1
2
Check electrical plug
Check/Replace fuse or
reset breaker
Vacuum cleaner won’t pick up dirt
Possible Causes
1
Incorrect Height Adjustment
2
Hose not attached to suction opening
3
Twist ‘n Snap Hose not securely attached
4
Crack or hole in Hose
Broken or worn Drive Belt
Rotating Floor Brush bristles worn
Rotating Floor Brush jammed
5
6
7
11
Clog in vacuum
Dirt Container full
Dirt Container not installed properly
Filters are dirty
12
Louvers missing or installed incorrectly
13
TurboBrush is clogged or debris is wrapped
around the Brush Roll
8
9
10
Remedies
Adjust Powerfoot to correct
height setting
2 Grasp Quick Reach Handle and
firmly push Hose Wand onto the
suction opening
3 Make sure Twist ‘n Snap Hose is
snapped into locked position
4 Check Hose and replace if needed
5 Replace Drive Belt, see pg. 10
6 Replace brush
7 Remove brush and clean debris from
brush ends
8 Clear clog, see pg. 11
9 Empty Dirt Container
10 Position correctly and lock in place
11 Check and clean Inner and Outer
Circular Filters and Pre-Motor Filters.
Replace HEPA Post-Motor Filter
12 Check for a clog in the tube in the
center of the Dirt Container, clear
and properly install Louvers
13 Maintaining TurboBrush, see page 9
1
Tools won't pick up dirt
Possible Cause
1
12
2
Crack or hole in Hose
Clog in vacuum
ug203-2829_6596_1105.indd 12
Remedies
1
2
Check Hose and replace if needed
Clear clog, see pg. 11
1/11/06 4:03:41 PM
Troubleshooting Continued
Tools won't pick up dirt, continued
Possible Cause
Remedies
5
Dirt Container full
Dirt Container or Upper Tank
not installed properly
Filters are dirty
6
Louver missing or installed incorrectly
3
4
3
4
5
6
Empty Dirt Container
Position correctly and
lock in place
Check and clean Inner and Outer
Circular Filters and Pre-Motor Filters.
Replace HEPA Post-Motor Filter
Check for a clog in the tube in the
center of the Dirt Container, clear
and properly install Louvers
Vacuum cleaner is difficult to push
Possible Causes
Remedies
1
Incorrect Height Adjustment
1
2
Brush Cover installed incorrectly
2
Adjust Powerfoot to correct
height setting
Make sure all three latches
are secured
Visible dirt escaping from cleaner
Possible Causes
Remedies
2
Dirt Container full
Filters missing or installed incorrectly
2
3
Dirt Container installed incorrectly
3
4
Filter Cup installed incorrectly
4
1
1
Empty Dirt Container
Check Inner and Outer Circular
Filters and HEPA Post-Motor Filter
for correct installation
Pull out and re-insert Dirt
Container correctly
Remove Dirt Container and make
sure Filter Cup is fully attached
If suggested solutions do not correct the problem, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
or visit the BISSELL website - www.bissell.com
13
ug203-2829_6596_1105.indd 13
1/11/06 4:03:41 PM
Replacement Parts – BISSELL PowerForce Turbo Bagless Series
You may purchase replacement parts from your retailer, by calling BISSELL Consumer Services
or by visiting our website. To locate a retailer near you, or to place an order using Visa,
MasterCard, Discover or American Express, call
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
Or visit our Website - www.bissell.com
Item Part No.
Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
32074
203-1297
203-1063
203-1099
203-1022
203-1216
203-1195
32064
32065
3205
203-1215
203-6828
203-1227
Style 7/9/10/12 Drive Belt (2-Pack)
Standard Headlight Bulb
Crevice Tool
Combination Dusting Brush / Upholstery Tool
Extension Wand
Wire Reinforced Twist ‘n Snap Vacuum Hose
Wide Brush Roll
Style 9/10/12 Inner & Outer Circular Filter Set
Style 9/10/12 Inner Circular Filter
Style 12 HEPA Filter
Pre-Motor Filter
TurboBrush Bracket
TurboBrush
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ug203-2829_6596_1105.indd 14
1/11/06 4:03:42 PM
BISSELL Consumer Services
For information about repairs or replacement parts, or
questions about your warranty, call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday
Saturday
8 a.m. — 10 p.m. ET
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It is your warranty.
15
ug203-2829_6596_1105.indd 15
1/11/06 4:03:43 PM
Warranty
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to
state. If you need additional instruction regarding this warranty or have questions regarding what it may cover,
please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare,
Inc. will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of
charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is
not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your
warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the “Customer Services” tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY
NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts,
so the above limitation may not apply to you.
16
ug203-2829_6596_1105.indd 16
©2005 BISSELL Homecare, Inc
Grand Rapids, Michigan
All rights reserved. Printed in Korea
Part Number 203-6829
Rev 11/05
Visit our website at:
www.bissell.com
1/11/06 4:03:43 PM