Rangemaster Elan 90 Dual Fuel User guide

90 Dual Fuel FSD
with Glide-out grill
User Guide for Australia
Installation & Service Instructions
U109635-02
Australia
Contents
Before you start...
3
Cooker Overview
5
Hotplate Burners
5
The Griddle
6
The Wok Cradle
7
The Glide-out Grill
8
The Ovens
9
The Clock
10
Multi-Function Oven
11
The Handyrack (Main Oven)
13
Tips on Cooking with the Timer
13
Oven Cooking chart - Conventional and Fan Ovens
14
General Oven Tips
15
Oven Shelves
15
Main Oven Light
16
Cleaning your Cooker
16
The Tall Oven
18
Troubleshooting
18
Service and Spares
20
Installation
21
Gas Connection
26
Conversion from Natural Gas to LP Gas
27
Electrical Connection
28
Servicing Notes
30
Circuit Diagram
35
Technical Data
36
2
Australia
Before you start...
Thank you for buying this Elan cooker. It should give you many years' trouble-free cooking if installed and operated
correctly. It is therefore important that you read this section before you start, particularly if you have not used a
dual fuel cooker before.
This appliance is designed for domestic cooking only. Using it for any other purpose could invalidate any warranty
or liability claim. In particular, the oven should NOT be used for heating the kitchen - besides invalidating claims,
this wastes fuel and may overheat the control knobs.
Installation and Maintenance
The installation must be in accordance with the relevant instructions in this booklet, with the relevant national and
local regulations, and with the local gas and electricity supply companies’ requirements.
Ensure that the gas supply is turned on and that the cooker is wired in and switched on (the cooker needs
electricity).
Set the clock to ensure that the left hand oven is functional - see the relevant section in this manual. The
right hand oven will function immediately, without the clock having to be set.
The cooker should be serviced only by a qualified service engineer, and only approved spare parts should be used.
Always allow the cooker to cool and then switch it off at the mains before cleaning or carrying out any maintenance
work, unless specified otherwise in this guide.
Peculiar smells
When you first use your cooker it may give off a slight odour. This should stop after a little use.
Before using for the first time, make sure that all packing materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200°C and run for an hour.
Before using the grill for the first time you should also turn on the grill and run for 30 minutes with the grill pan in
position, pushed fully back, and the grill door open.
Make sure the room is well ventilated to the outside air (see 'Ventilation' below). People with respiratory or
allergy problems should vacate the area for this brief period.
If you smell gas
•
•
•
•
•
•
•
Don’t turn electric switches on or off.
Don’t smoke
Don’t use naked flames
Do turn off the gas at the meter or cylinder
Do open doors and windows to get rid of the gas
Do keep people away from the area affected
Do call your gas supplier.
Ventilation
The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is
installed. Therefore, ensure that the kitchen is well ventilated: keep natural ventilation holes open or install a
powered cooker hood that vents outside. If you have several burners on, or use the cooker for a long time, open a
window or turn on an extractor fan.
Personal Safety
Accessible parts will become hot during use and will retain heat even after you have stopped cooking.
Keep babies and children away from the cooker and never wear loose-fitting or hanging clothes while the
appliance is in use. Always be certain that the controls are in the OFF position when the oven is not in use,
and before attempting to clean the cooker.
When the oven is on, DO NOT leave the oven door open for longer than necessary - otherwise, the control knobs
may become very hot.
3
Australia
Cooking high moisture content foods can create a ‘steam burst’ when the oven door is opened. When opening
the oven, stand well back and allow any steam to disperse.
Always keep combustible materials, e.g. curtains, and flammable liquids a safe distance away from your cooker.
Do not spray aerosols in the vicinity of the cooker while it is on.
Use dry oven gloves when applicable - using damp gloves might result in steam burns when you touch a hot
surface. Do not use a towel or other bulky cloth in place of a glove - it might catch fire if brought into contact with a
hot surface.
Never operate the cooker with wet hands.
Do not use aluminium foil to cover shelves, linings or the oven roof.
Never heat unopened food containers. Pressure build up may cause the containers to burst and cause injury.
Do not use unstable saucepans. Always ensure that you position the handles away from the edge of the hotplate.
Never leave the hotplate unattended at high heat settings. Pans boiling over can cause smoking, and greasy
spills may catch on fire. Use a deep fat thermometer whenever possible to prevent fat overheating beyond the
smoking point.
Never leave a chip pan unattended. Always heat fat slowly, and watch as it heats. Deep fry pans should be only one
third full of fat. Filling the pan too full of fat can cause spill over when food is added. If you use a combination of oils
or fats in frying, stir them together before heating, or as the fats melt.
Foods for frying should be as dry as possible. Frost on frozen foods or moisture on fresh foods can cause hot fat to
bubble up and over the sides of the pan. Carefully watch for spills or overheating of foods when frying at high or
medium high temperatures. Never try to move a pan of hot fat, especially a deep fat fryer. Wait until the fat is cool.
Do not use the top of the flue (the slot along the back of the cooker) for warming plates, dishes, drying tea towels
or softening butter.
Do not use water on grease fires and never pick up a flaming pan. Turn the controls off and then smother
a flaming pan on a surface unit by covering the pan completely with a well fitting lid or baking tray. If
available, use a multipurpose dry chemical or foam-type fire extinguisher.
Take care that no water seeps into the appliance.
Only certain types of glass, glass-ceramic, earthenware or other glazed containers are suitable for hotplate cooking;
others may break because of the sudden change in temperature.
This appliance is heavy, so take care when moving it.
Cleaning
In the interests of hygiene and safety, the cooker should be kept clean at all times as a build up in fats and other
food stuff could result in a fire.
Clean only the parts listed in this guide.
Clean with caution. If a wet sponge or cloth is used to wipe spills on a hot surface, be careful to avoid steam burns.
Some cleansers can produce noxious fumes if applied to a hot surface.
4
Australia
Cooker Overview
Hotplate Burners
The drawing by each knob
indicates which burner that knob
controls.
This is the left hand front burner
knob.
Each burner has an FSD
(Flame Security Device) that
will stop the flow of gas if the
flame goes out.
���������������
�������������������
Press the igniter button, and
push in and turn a knob to
the large flame symbol ( ).
��������
Keep holding the knob pressed in for a few seconds.
This lets gas through to the burner so that the safety
device can detect the flame.
If, when you let go of the control knob, the burner
goes out, the safety device has not been bypassed.
Turn the control to the off position and wait one
minute and then try again, this time holding in the
control knob for slightly longer.
The Elan 90 Dual Fuel cooker has the following features:
• Five hotplate burners, including a wok burner,
with FSDs (Flame Security Devices).
• A control panel.
• A glide-out grill.
• A main (multi-function) left hand oven.
• A tall (fan) right hand oven.
References to 'left hand' and 'right hand' ovens
apply as viewed from the front of the appliance.
Adjust the flame height to suit
by turning the knob. On this
cooker the low position is beyond
high, not between high and off.
The small flame marks the ‘low
position’. Turn the knob towards
it after the contents of a pan have
boiled.
Make sure flames are under the pans. Using a lid will
help the contents boil more quickly.
Pans and kettles with concave bases or down turned
base rims should not be used.
5
Australia
The Griddle
Simmering aids, such as asbestos or mesh mats, are NOT
recommended. They will reduce burner performance
and could damage the pan supports.
The griddle fits the left hand pan support, front to back.
It is designed for cooking food on directly. Don’t use
pans of any kind on it. The griddle surface is non-stick
and metal cooking utensils (e.g. spatulas) will damage
the surface. Use utensils made of either heat-resistant
plastic or wood.
Avoid using unstable and misshapen pans that may
tilt easily, and pans with a very small base diameter,
e.g. milk pans, single egg poachers. The minimum pan
diameter recommended is 120mm (about 43/4").
Don’t put the griddle crossways - it will not fit properly
and will be unstable.
Don’t put it on the Wok burners - it is not designed to fit
the Wok burner pan supports.
The Wok burners are designed to provide even heat
over a large area. They are ideal for large pans and stir
frying. For heating smaller pans, the smaller burners
may be more efficient.
Position the griddle over the hotplate burners resting
on the pan support. Check that it is securely located.
When the ignition button is pressed in, sparks will
be created at every burner (this is normal).
The griddle can be lightly brushed with cooking oil
before use. Light the hotplate burners. Adjust the flame
heights to suit.
If, after lighting, a hotplate burner’s flame goes out, turn
it off and leave it for one minute before relighting it.
You can remove the burner cap and trim rings for
cleaning - see the 'Cleaning your Cooker' section of
these instructions.
You should wipe the enamel top surface of the cooker
around the hotplate burners as soon as possible after
spills occur. Try to wipe them off while the enamel is still
warm.
Note:
Use of aluminium pans may cause metallic marking
of the pan supports. This does not affect the
durability of the enamel and may be cleaned off
with an appropriate cleaner (refer to 'Cleaning your
Cooker').
Preheat the griddle for a maximum of 5 minutes before
adding food. Leaving it longer may cause damage. The
controls can be turned to a lower position simply by
turning the control knobs towards the lower position
marked with the small flame symbol.
6
Australia
Always leave space around the griddle for the gases to
escape. Never fit two griddles side by side. Large pans
should also be spaced well apart.
The cradle should be used on the triple ring Wok burner
only.
When you fit the cradle, check that the Wok is properly
located on the front and rear fingers and that it is
supported properly on a pan support.
Use the following heat settings as a guide for griddle
cooking.
High/medium:
Drop scones, Bacon, Chops, Steak, Burgers.
Medium/low:
Potato cakes, Eggs, Fish cakes.
Make sure the cradle is stable and that the Wok is sitting
level in the ring.
Experience will soon familiarise you with the correct
setting to use for cooking.
After cooking, allow the griddle to cool before cleaning.
The Wok Cradle
The cradle will get very hot in use - allow plenty of
time for it to cool before you pick it up.
The Wok cradle is designed to fit a Professional 35cm
Wok (available from our cookware collection - Part Code
RM095).
If you use a different Wok make sure that it fits the
cradle. Woks vary very widely in size and shape. It’s
important that the Wok sits down on the pan support
- but if the Wok is too small the cradle will not support it
properly.
7
Australia
The Glide-out Grill
The grill trivet can be removed and the food placed on
it while you are waiting for the grill to preheat.
Open the grill door and pull the grill pan carriage
forward using the handle.
The grill pan and grill pan carriage can be easily
removed for cleaning. See ‘Cleaning your Cooker’.
When you pull the grill pan forward, ensure that the
wide rim is at the front.
The grill pan gets very hot when the grill is on. Don't
touch the pan or trivet unless you are sure it is cool.
After placing your food on the grill grid, slide the grill
carriage into the grill chamber. Make sure it is pushed
right in.
The grill has two elements that allow either the whole
area of the pan to be heated or just the right hand half.
To heat the whole grill, turn the knob clockwise.
To heat the right hand half turn it anticlockwise.
The neon indicator light by the grill control will come
on.
For best results, especially with toast, preheat for 2
minutes with the grill pan in position. After placing
your food on the grill pan grid, slide in the grill
carriage. Adjust the heat to suit by turning the knob.
Make sure the grill carriage is pushed right in.
Never close the grill door when the grill is on.
The grill pan grid can be turned over to give two grilling
positions.
Don’t leave the grill on for more than a few moments,
without the grill pan underneath it.
Before you remove any of the grill parts for cleaning
make sure that they are cool or use oven gloves.
8
Australia
The Ovens
During use the appliance becomes hot. Care should be taken to avoid touching the heating elements
inside the oven.
The clock must be set before the ovens will work. See ‘The Clock’ section for instructions on setting the time of
day.
The Left Hand Oven
The Right Hand Tall Oven
The left hand oven is a Multi-function oven. As well as
the oven fan and fan element, it is fitted with two extra
heating elements, one visible in the top of the oven
and the second under the oven base. Take care to avoid
touching the top element and element deflector when
placing or removing items from the oven.
The fan in the right hand oven circulates hot air
continuously, which means faster more even cooking.
The recommended cooking temperatures for a fanned
oven are generally lower than for a non-fanned oven.
For more detail on this oven see the section dedicated
to the ‘Multi-Function Oven’..
The Multi-function
oven has two
controls: a function
selector and a
temperature setting
knob.
The right hand
fan oven control is
at the right hand
end of the control
panel.
Turn the function selector
control to a cooking
function. This is the fan oven
setting.
Turn the oven temperature
knob to the temperature
you need.
Turn the oven temperature
knob to the temperature
you need. The oven heating
light will glow until the
oven has reached the
temperature you selected.
It will then cycle on and off
during cooking.
The oven indicator light
will glow until the oven has
reached the temperature
you selected. It will then
cycle on and off during
cooking
9
Australia
The Clock
ticks down. To stop the beeper when it sounds, turn the
Adjusting knob anticlockwise.
This must be set before the ovens will work.
Setting the time of day
To stop the ovens at a specific time of
day
Turn the Timer knob to the (
Timer knob
Adjusting knob
) position.
Use the Adjusting knob to set the time at which the
ovens are to stop. You can set the ovens to turn on
at any time over the following 24 hour period. AUTO
shows in the display:
When the clock is first connected, the display flashes
(
) and (
) alternately.
To set the time, turn and hold the Timer knob to
the clock symbol ( ) and at the same time turn the
Adjusting knob left or right until the clock shows the
time of day. Remember this is a 24-hour clock. Let go
of the Timer knob and it will spring back to the vertical,
oven manual setting.
The following sections show you how to use the
various clock functions, which apply to both
ovens simultaneously. If both ovens are cooking
automatically using the timer, you can control them
individually using the different oven temperature
knobs.
Minute Minder
This function acts as a reminder, setting a beeper to
sound after a set number of minutes. Turn the Timer
knob to the right to the ( ) minute minder setting - it
should click into position:
Turn the Timer knob to the bottom ‘Auto’ setting. Once
the set time is reached, the beeper sounds. Turn the
Timer knob to the vertical ( ) to return to manual
cooking.
To start and then stop the ovens using
the Timer
Before you set the clock, decide on both the ‘cook time’,
which is the period of time you want the oven to cook,
and the ‘stop time’, which is the time of day at which you
want the oven to stop cooking.
You cannot set a start time directly - this is set
automatically by a combination of the 'cook time'
and 'stop time'.
Turn the Timer knob to the (
) position:
Use the Adjusting knob to set the time you need as
below:
Use the Adjusting knob to set the ‘cooking time’ you
need:
You can either turn the knob back to the vertical
manual setting ( ) to keep an eye on the time of day,
or leave it in the ( ) minute minder position as the time
10
Australia
Turn the Timer knob to the ( ) position. The display
will show the current time of day plus the ‘cook time’
you just set. Use the Adjusting knob to set the ‘stop
time’ you need:
The ovens are now locked, as is confirmed by the
display showing the time of day alongside the key
symbol:
To turn off the key lock
Turn and hold the Timer knob to the clock symbol (
for about 8 seconds. ‘OF’ will appear on the display.
The ‘stop time’ is displayed, followed by 'AUTO'. Set the
oven to the cooking temperature you need. Turn the
Timer knob to the ‘Auto’ setting.
)
When your cooking is finished, the beeper sounds. Turn
the Timer knob to the vertical ( ) to return to manual
cooking.
If you are out, don’t worry about the beeper going off
- it stops on its own after a while. When you return, turn
the Timer knob to the vertical ( ) to return to manual
cooking.
Keep holding the Timer knob turned to the clock
symbol ( ) and turn the Adjusting knob clockwise
until the key symbol ( ) goes out on the display and ‘On’
shows. Let go of the knobs.
AUTO is showing, but you want to revert to manual
cooking
You can cancel any automatic settings by briefly turning
the Timer knob to the clock symbol ( ) and then
releasing it.
Key Lock
When the key lock is activated, the ovens will not come
on.
To activate the key lock
After a few seconds, the display reverts to showing the
time of day:
Make sure that the clock is in manual mode and cancel
any active programs.
Turn and hold the Timer knob to the clock symbol (
for about 8 seconds. ‘On’ appears on the display:
)
The ovens can now be used normally.
Multi-Function Oven
Keep holding the Timer knob turned to the clock
symbol ( ) and turn the Adjusting knob clockwise until
the key symbol ( ) and ‘Of’ show on the display. Let go of
the knobs.
11
The Multi-function oven is on the left hand side.
It has many varied uses. We suggest you keep a
careful eye on your cooking until you are familiar
with each function. Remember - not all functions
will be suitable for all food types.
Australia
Fanned grilling
This function operates the fan while the top
element is on. It produces a more even, less fierce
heat than a conventional grill. For best results, place
the food to be grilled, on a grid over a roasting tin,
which should be smaller than a conventional grill
pan. This allows greater air circulation. Thick pieces
of meat or fish are ideal for grilling in this way, as
the circulated air reduces the fierceness of the heat
from the grill. The oven door should be kept closed
while grilling is in progress, thereby saving energy.
You will also find that the food needs to be watched
and turned less than for normal grilling.
Please remember that all cookers vary - temperatures
in your new Elan cooker may differ from those in your
previous cooker.
Pre-heat this function before cooking.
Fan assisted oven
Multi-Function Oven Functions
Defrost
This function operates the fan, circulating air
heated by the elements at the top and the base of
the oven. The combination of fan and conventional
cooking (top and base heat) makes this function
ideal for cooking large items that need thorough
cooking, such as a large roast. It is also possible to
bake on two shelves at one time, although they will
need to be swapped over during the cooking time,
as the heat at the top of the oven is greater than at
the base, when using this function.
This function causes the fan to circulate cold
air only. This enables small items such as desserts,
cream cakes and pieces of meat, fish and poultry to
be defrosted.
Defrosting in this way speeds up the process and
protects the food from flies. Pieces of meat, fish and
poultry should be placed on a rack, over a tray to
catch any drips. Be sure to wash the rack and tray
after defrosting.
This is a fast intensive form of cooking; keep an
eye on the food cooking until you have become
accustomed to the function.
Defrost with the oven door closed.
Large items, such as whole chickens and
joints should not be defrosted in this way. We
recommend this be carried out in a refrigerator.
Conventional oven (top and base
heat)
This function combines the heat from the top and
base elements. It is particularly suitable for roasting
and baking pastry, cakes and biscuits. Food cooked
on the top shelf will brown and crisp faster than
on the lower shelf, because the heat is greater at
the top of the oven than at the base, as for the
‘Fan assisted oven’ function. Similar items being
cooked will need to be swapped around for even
cooking. This means that foods requiring different
temperatures can be cooked together, using the
cooler zone in the lower half of the oven and hotter
area to the top.
Defrosting should not be carried out in a warm
oven or when an adjoining oven is in use or still
warm.
Ensure that dairy foods, meat and poultry are
completely defrosted before cooking.
Fan oven
This function operates the fan and the
heating element around it. An even heat is
produced throughout the oven, allowing you to
cook large amounts quickly.
Fan oven cooking is particularly suitable for baking
on several shelves at one time and is an efficient
‘all-round’ function. It may be necessary to reduce
the temperature by approximately 10°C for recipes
previously cooked in a conventional oven.
Browning element
This function uses the element in the top
of the oven only. It is a useful function for the
browning or finishing of pasta dishes, vegetables in
sauce, etc.
If you wish to pre-heat the oven, wait until the
indicator light has gone out before inserting the
food.
12
Australia
Base heat
This function uses the base element only. It
will crisp up your pizza or quiche base, or finish off
cooking the base of a pastry case on a lower shelf.
It is also a gentle heat, good for the slow cooking
of casseroles in the middle of the oven or for plate
warming.
The Handyrack (Main Oven)
The maximum weight that can be held by the
Handyrack is 5.5kg (12lb). It should only be used with
the supplied roasting tin, which is designed to fit the
Handyrack. Any other vessel could be unstable.
Additional roasting tins are available from our cookware
collection - Part Code RM027.
Tips on Cooking with the Timer
If you want to cook more than one dish, choose dishes
that require approximately the same time. However,
dishes can be ‘slowed down’ slightly by using small
containers and covering them with aluminium foil, or
‘speeded up’ slightly by cooking smaller quantities or
placing them in larger containers. Very perishable foods
such as pork or fish should be avoided if a long delay
period is planned, especially in hot weather.
For reasons of health, don’t place warm food in the
ovens if they are to be operated using a timer, and
don’t program the ovens if one or other of them is
already warm.
The Handyrack fits to the left hand Main Oven door
only. Food cooking on it is easy to attend to, because it’s
accessible when the door is open.
Whole poultry must be thoroughly defrosted before
being placed in the oven. Check that meat and poultry
are fully cooked before serving.
It can be fitted at two different heights. One of the oven
shelves must be removed and the other positioned to
suit.
The oven control settings and cooking
times given in the table overleaf are
intended to be used only as a guide.
Individual tastes may require the
temperature to be altered to provide a
preferred result.
When the Handyrack is used in its highest position,
other dishes can be cooked on the bottom shelf
position or base of the oven.
For best results pre-heat the oven until the
oven indicator light goes out.
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or
base of the oven.
When using recipes, reduce the temperature
by 10°C and the cooking time by 5-10 minutes.
The temperatures in the fanned ovens do not
vary with height - so you can use any shelf.
To fit the Handyrack, locate one side of it on the door
bracket:
Always leave at least one runner space
between shelves when 2 tier cooking. Place
baking trays, individual cake tins or baking
dishes in the middle of the oven shelf.
Then spring the other side out to clip it onto the other
bracket.
13
Australia
Oven Cooking chart - Conventional and Fan Ovens
Conventional Oven
setting in Left Hand Oven
Shelf
Temperature
Position
Food
Fan Oven
Temperature Approximate Cooking Time
FISH
190°C
190°C
190°C
3
3
3
180°C
180°C
180°C
Fillets 15-20mins.
Whole 10mins.per 500g + 10mins.
Steaks according to thickness.
ROAST MEATS
Beef with bone
160°C
2-3
150°C
20-25mins. per 500g + 20-25mins.
200°C
2-3
190°C
15-20mins. per 500g + 15-20mins.
Beef without bone
160°C
2-3
150°C
30-35mins. per 500g + 30-35mins.
200°C
2-3
190°C
20-25mins. per 500g + 20-25mins.
Lamb
160°C
2-3
170°C
30-35mins. per 500g + 30-35mins.
200°C
2-3
190°C
25-35mins. per 500g + 25-30mins.
Pork
160°C
2-3
150°C
35-40mins. per 500g + 35-40mins.
200°C
2-3
190°C
25-30mins. per 500g + 25-30mins.
Stuffed and rolled - Add approx. 10 mins. per 500g to above cooking times, or cook at 200°C for 20mins., then 160°C for the
remainder.
THOROUGHLY THAW FROZEN JOINTS AND POULTRY BEFORE COOKING.
POULTRY
Chicken
160°C
2-3
150°C
20-25mins. per 500g + 20-25mins.
200°C
2-3
190°C
15-20mins. per 500g + 15-20mins.
Turkey
160°C
2
150°C
20-25mins. per 500g + 20-25mins.
200°C
2
190°C
15-20mins. per 500g + 15-20mins.
Stuffed Poultry - Cook at 200°C or at 200°C for 20mins. then 160°C for the remainder. For pre-packed (fresh or frozen) food,
follow the instructions on the pack.
CASSEROLE
140-150°C
2-3
140°C
2-4hrs according to recipe
YORKSHIRE PUDDING
220°C
4
200°C
Large tin 30-35mins. Individual 10-20mins.
CAKES
Very Rich Fruit
Rich fruit (180mm)
Scones
140°C
150°C
200°C
2
2
2 & 4 or 3
140°C
145°C
190°C
45-50mins. per 500g mixture
21/2-3hrs.
10-15mins.
200°C
200°C
200°C
220°C
220°C
110°C
2&4
2&4
4
2, 3 or 4
2&4
3
190°C
190°C
190°C
200°C
200°C
100°C
45-50mins. Interchange after 25mins.
35-40mins.
15-20mins. according to size.
20-40mins. according to size.
20-30mins.
2-21/2hrs
PASTRIES
Plate Tart
Fruit Pie
Tartlets
Puff Pastry
BREAD
MERINGUES
500g is approximately 1lb (1lb 2oz)
14
Australia
Oven Shelves
General Oven Tips
Left Hand (Main) Oven
The wire shelves in an oven should always be pushed
firmly to the back of the oven.
Baking trays, roasting tins, etc., should be placed
level in the middle of the oven’s wire shelves. Keep all
trays and containers away from the sides of the oven
- otherwise, overbrowning of the food may occur.
For even browning, the maximum recommended size
of a baking tray is 340mm by 340mm for the left hand
(main) oven, and 230mm by 320mm for the right hand
(tall) oven.
Food is cooked at lower temperature in a fan oven
than in a conventional oven. When using recipes,
reduce the temperature by 10°C and the cooking time
by 5-10 minutes. The temperature in the fanned oven
does not vary with height in the oven - so you can use
any shelf.
The shelf guard should be at the back pointing upwards
As well as the flat shelf, some models are supplied with
a drop shelf, which increases the spacing possibilities:
The shelves should not be fitted directly one above
the other. When cooking on more than one shelf
always leave at least one runner space between
them.
You can easily remove and refit the oven shelves, as
follows:
Pull the shelf forward until the back of the shelf is
stopped by the shelf stop bumps in the oven sides.
Always leave a ‘finger's width’ between dishes on the
same shelf. This allows the heat to circulate freely
around them.
The Cook & Clean oven panels (see 'Cleaning your
Cooker') work better when fat splashes are avoided.
Cover meat when cooking.
Lift up the front of the shelf so the back of the shelf
will pass under the shelf stop and then pull the shelf
forward:
To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.
If you want to brown the base of a pastry dish, preheat a
baking tray for 15 minutes before placing the dish in the
centre of the tray.
Where dishes may boil and spill over during cooking,
place them on a baking tray.
To refit the shelf, line up the shelf with a groove in the
oven side and push the shelf back until the ends hit the
shelf stop. Lift up the front so that the shelf ends clear
the shelf stops, and then lower the front so that the
shelf is level, and push it fully back.
15
Australia
Right Hand (Tall) Oven
Hotplate Burners
The tall oven is supplied with four normal cooking
shelves
Some models have a separate trim ring, which fits on
the burner head.
The burner heads and caps can be removed for
cleaning. Make sure they are absolutely dry before
replacing them.
and a plate warming shelf.
The single ring burners
When refitting the burner head, ensure that the notch
lines up with the electrode or hole in the base. Check
that the burner head is level and that the cap is fitted
centrally on the burner head:
When using the tall oven you can cook on all four
shelves at the same time; but make sure they are well
spaced out to allow the hot air to circulate.
Main Oven Light
Press the button to turn the light on:
A cap, B head, C notch, D electrode, E base
If the oven light fails, turn off the power supply before
you change the bulb. See the ‘Troubleshooting’ section
for details on how to change the bulb.
The Wok Burner
The Wok burner is a little more complicated but it can
also be taken apart for cleaning.
Cleaning your Cooker
Essential Information
Isolate the electricity supply before carrying out any
thorough cleaning. Then allow the cooker to cool.
Never use paint solvents, washing soda, caustic
cleaners, biological powders, bleach, chlorine based
bleach cleaners, coarse abrasives or salt. Don’t mix
different cleaning products - they may react together
with hazardous results.
All parts of the cooker can be cleaned with hot soapy
water - but take care that no surplus water seeps into
the appliance.
Remember to switch on the electricity supply and reset
the clock before re-using the cooker.
We have developed a range of cleaning products that give
maximum performance without damaging the enamel
and painted surfaces. More information is available
through either the Cookware Collection brochure supplied
with your cooker or our website www.rangemaster.co.uk.
Wok burner
16
Australia
A inner burner cap,
C inner burner head
E Wok burner base
B
D
When refitting the grill pan, ensure that the wide rim is
at the front:
outer burner cap
outer burner head
When re-assembling the Wok burner, turn over the large
base ring and find the ‘D’ shaped area:
Control Panel and Doors
Avoid using any abrasive cleaners, including cream
cleaners, on brushed Stainless Steel surfaces. For best
results, use a liquid detergent.
Turn the head until the ‘D’ matches the one on the
burner base. Turn the head over and place it on the
burner base.
To fit the small inner burner, find the larger electrode
notch in the burner rim. Line this up with the white
ignition electrode and place the inner burner on the
large base ring.
The control panel and knobs, and doors, should only be
cleaned with a soft cloth wrung out in clean hot soapy
water. After cleaning, polish with a dry cloth.
The Main Oven
The Main oven has panels which have been coated with
a special enamel that partly cleans itself. This does not
stop all marks on the lining, but helps to reduce the
amount of manual cleaning needed.
The Cook & Clean panels work better above 200°C. If
you do most of your cooking below this temperature,
occasionally remove the panels and wipe with a lint
free cloth and hot soapy water. The panels should
then be dried and replaced and the oven heated at
200°C for about one hour. This will ensure that the
Cook & Clean panels are working effectively.
Don’t use steel wool, oven cleaning pads, or any other
materials that will scratch the surface.
A electrode notch
B
ignition electrode
Now fit the two burner caps, ensuring that they are
seated properly.
The Wok Cradle
Recommended cleaning materials are hot soapy water,
a moistened soap pad, cream cleaner or a nylon scourer.
Removing the Main Oven Linings
Some of the lining panels can be removed for cleaning.
You will need to remove the shelves before removing
the panels.
Each side of the oven is fixed with four fixing screws.
You don’t have to remove the screws to remove the
oven linings. Simply lift each side panel upwards and
they will slide off the screws. Then pull them forwards:
Grill
Before you remove any of the grill parts for cleaning.
ensure that they are cool, or use oven gloves.
The grill pan and grill pan carriage can be easily
removed for cleaning.
The grill pan and grid should be washed in hot soapy
water, or using our recommended Rangemaster
cleaning solution.
Once the linings are removed, the oven enamel interior
can be cleaned.
After grilling meats or any foods that soil, leave to soak
for a few minutes in the sink immediately after use.
Stubborn particles may be removed from the grid by
using a nylon brush.
17
Australia
The Tall Oven
To clean the oven sides, slide out the shelves, unhook
the supports from the oven sides, and lift out:
An oven is not cooking evenly
Do not use a baking tray with dimensions larger
than those specified in the section on 'General
Oven Tips'.
If you are cooking a large item, be prepared to turn
it round during cooking.
If two shelves are used, check that space has been
left for the heat to circulate. When a baking tray is
put into the oven, ensure that it is placed centrally
on the shelf.
Check that the door seal is not damaged and that
the door catch is adjusted so that the door is held
firmly against the seal.
A dish of water when placed on the shelf should be
the same depth all over. (For example, if it is deeper
at the back, then the back of the cooker should be
raised up or the front lowered). If the cooker is not
level, arrange for your supplier to level it for you.
Troubleshooting
Noisy oven fan
The tone of an oven fan may change as the oven
heats up - this is perfectly normal.
Grill not cooking properly
Are you using the pan and trivet supplied with
the cooker? Is the pan being used on the runners,
not the floor of the compartment? Is the grill tray
pushed fully back to the stop position?
The knobs get hot when I use the oven or the grill.
Can I avoid this?
Yes, this is caused by heat rising from the oven or
the grill, and heating them up. Don’t leave the oven
door open. Make sure that the grill pan is pushed
right back to the ‘back stop’ when grilling. Always
grill with the grill compartment door open.
If there is an installation problem and I don’t get my
original installer to come back to fix it, who pays?
You do. Service organisations will charge for their
call-outs if they are correcting work carried out by
your original installer. Therefore, it’s in your own
interest to keep track of this installer so that you
can contact them as required.
Power failure
In the event of a failure in the electrical supply,
remember to reset the clock to ensure that the
timed oven continues to operate.
Food is cooking too slowly, too quickly, or burning
Cooking times may differ from your previous
oven. Check that you are using the recommended
temperatures and shelf positions - see the oven
cooking guide. Then adjust the settings according
to your own individual tastes.
An oven is not coming on when switched on
manually
Is the power on? Is the clock illuminated? If not,
there may be something wrong with the power
supply. Is the cooker supply on at the isolator
switch?
Has the time of day been set?
Is the key symbol ( ) showing in the display to
signify that the oven is locked? See the 'Clock'
section of the instructions for more information on
the key lock feature.
An oven is not coming on when programmed using
the Timer
Has the oven knob been left in the OFF position by
mistake? Is the oven locked (see above)?
Oven temperature getting hotter as the cooker gets
older
If turning the temperature down using the
oven control knob has not worked, or has only
worked for a short time, then you may need a
new thermostat. This should be fitted by a service
person.
The oven light is not working
The bulb has probably blown. You can buy a
replacement bulb (which is not covered under the
guarantee) from most electrical stores. Ask for an
Edison screw fitting 15w 240v lamp, FOR OVENS. It
must be a special bulb, heat resistant to 300 °C. See
the HELP leaflet for spares by mail order.
18
Australia
Before removing the existing bulb, turn off the
power supply and ensure that the oven is cool.
Open the oven door and remove the oven shelves.
Locate the bulb cover and unscrew it by turning it
anticlockwise (it may be very stiff ):
Now unscrew the existing bulb anticlockwise,
taking care to protect your fingers with a glove in
case the bulb should shatter.
Screw in the new bulb clockwise and then screw
the bulb cover back on. Turn on the electricity
supply and check that the bulb now lights.
Hotplate ignition or hotplate burners faulty
Is the power on? Is the clock illuminated? If not,
there maybe something wrong with the power
supply.
Are the sparker (ignition electrode) or burner slots
blocked by debris?
Are the burner trim and caps correctly located (see
the section on ‘Cleaning your Cooker’)?
Hotplate burners will not light
Make sure that the burner parts have been replaced
correctly after wiping or removing for cleaning.
Check that there is not a problem with your gas
supply. You can do this by making sure that other
gas appliances you may have are working.
Do the burners spark when you push the button? If
not, verify that the power is on by checking that the
clock is illuminated.
19
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Service and Spares
Firstly, please complete the appliance details below and keep them safe for future reference - this information
will enable us to accurately identify your particular appliance and help us to help you. Filling this in now will
save you time and inconvenience if you later have a problem with your appliance. It may also be of benefit to
keep your purchase receipt with this leaflet. You may be required to produce the receipt to validate a warranty
field visit.
Retailers Name & Address
Andi Appliances Pty Ltd.
1 Stamford Road, Oakleigh, VIC 3166.
Tel No : (03) 9569 1255
Fax No : (03) 9569 1450
Email : Service@andico.com.au
Name of Appliance: Elan 90 Dual Fuel
Appliance Serial Number *
Fuel Type: Dual Fuel
Date of Purchase
Installer's Name, Address and Telephone No.
Date of Installation
* This information is on the appliance data badge.
If you have a problem
In the unlikely event that you have a problem with your appliance, please refer in the first instance to the
remainder of this booklet, especially the 'Troubleshooting' section, to check that you are using the appliance
correctly. If you are still having difficulty, contact your retailer.
Please note
If your appliance is outside the 12-month warranty period, our service provider may charge for this visit.
If you request an engineer to visit and the fault is not the responsibility of the manufacture, our service
provider reserves the right to make a charge.
Appointments not kept by you may be subject to a charge.
Out of Warranty
We recommend that our appliances are serviced regularly throughout their life to maintain the best
performance and efficiency. The frequency of service will depend on usage - for normal usage once a year
should suffice. Service work should only be carried out by an authorised person.
Spare Parts
To maintain optimum and safe performance, we recommend that only genuine spare parts are used. Do not
use re-conditioned or unauthorised gas controls.
20
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Installation
Conversion
All models are supplied by default for use with
natural gas. A conversion kit for use with Propane
is included with the appliance. See the instructions
that are supplied with the conversion kit, and
included in these instructions.
Dear Installer
Before you start your installation, please complete
the details on the previous sheet. This is so that,
if your customer has a problem relating to your
installation, they will be able to contact you easily.
After converting the appliance, please attach the
Gas Conversion sticker over the appropriate area
of the data badge. This will identify the gas type for
which the appliance is now set.
You must be aware of the following
safety requirements & regulations
The cooker must be installed in a well-ventilated
space, as specified in:
You will need the following equipment to
complete the cooker installation satisfactorily:
‘AS 5601/AG 601 - Gas Installations’.
GAS PRESSURE TESTER
The installation must also be in accordance with
all local gas fitting regulations, municipal building
codes, electrical wiring regulations and any other
relevant statutory regulations.
In your own interests and those of safety, it is law
that all gas appliances be installed by an authorised
person. Failure to install the appliance correctly
could invalidate any warranty or liability claims and
lead to prosecution.
FLEXIBLE GAS HOSE
Must be in accordance with
the relevant standards.
Before installation, ensure that the cooker is
suitable for your gas type and supply voltage. See
the data badge. This appliance can be converted for
use on Propane.
Warning: where this appliance is installed in
marine craft or in caravans, it shall not be used
as a space heater.
This appliance is designed for domestic cooking
only. Use for any other purpose could invalidate
any warranty or liability claim.
Ventilation Requirements
The room containing the appliance should have an
adequate air supply.
An appliance should be installed in a location for
complete combustion of gas, proper flueing and to
maintain ambient temperature of the immediate
surrounding at safe limits, under normal operation
condition.
Failure to install appliances correctly is
dangerous and could lead to prosecution.
Location of Cooker
The cooker may be installed in a kitchen/kitchen
diner but NOT in a room containing a bath or
shower.
MULTIMETER
(for electrical checks)
You will also need the following tools:
1.
2.
Electric drill
Masonry drill bit
(only required if fitting the cooker on a
stone or concrete floor)
3. Rawlplugs
(only required if fitting the cooker on a
stone or concrete floor)
4. Screws for fitting stability bracket
5. Pencil
6. Steel tape measure
7. Cross head screwdriver
8. Flat head screwdriver
9. 4mm & 3mm Allen keys
10. Spirit level
11. Adjustable spanner
21
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Checking the parts
Positioning the Cooker - Clearances
(see AS 5601/AG 601)
4 pan supports
Griddle plate
Grill pan and trivet
Levelling tool
1. Overhead - Measurement A
Handyrack
The minimum height of any surface above the cooker is
650mm above the hotplate.
Range hoods and exhaust fans shall be installed in
accordance with the manufacturer’s instructions. However,
in no case shall the clearance between the highest part of
the hob of the cooking appliance and a range hood be less
than 650 mm or, for an overhead exhaust fan, 750 mm.
Roasting tin
2. Side clearances - Measurements B & C
2 flat oven shelves and 2 drop
shelves.
Splashback & Plinth
Conversion kit from Natural
gas to Propane gas
Hand rail and door handles
Restraining chain and hook
Stability bracket
Where B, measured from the periphery of the nearest
burner to any vertical combustible surface, or vertical
combustible surface covered with toughened glass or sheet
metal, is less than 200 mm, the surface shall be protected
to ensure that the combustible surface does not exceed
65ºC above ambient*. Even with the surface protected,
the dimension B should not be less than 135mm above
hotplate level.
*The fixing of 5mm thick ceramic tiles to the surface, or
attaching fire resistant material to the surface and covering
with sheet metal with a minimum thickness of 0.4mm to
a height C of not less than 150 mm above the hotplate,
should satisfy this requirement.
22
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Unpacking the Cooker
Do not take any packaging off the cooker until it
is directly in front of the location where is to be
installed (unless it will not fit through a door in its
outer packaging). Cut the banding straps and lift
the cardboard box off the cooker, leaving the cooker
standing on the base packaging. See the loose
unpacking sheet.
Moving the Cooker
On no account try and move the cooker while it is
plugged into the electricity supply.
The cooker is very heavy, and great care needs to be
taken. We recommend that two people manoeuvre
it. Ensure that the floor covering is firmly fixed, or
removed, to prevent it being disturbed when moving
the cooker around.
3. Side clearances - Measurement E
Where D, the distance from the periphery of the nearest
burner to a horizontal combustible surface is less than
200 mm, then E shall be 10 mm or more, or the horizontal
surface shall be above the trivet. See insets above.
We recommend a gap of 1110mm between units to allow
for moving the cooker. If a flush fit is required, fit the cooker
up to the unit at one side then fit the unit the other side.
A clearance of 130mm is required if the cooker is near a
corner of the kitchen, to allow the oven doors to open.
Do not box the cooker in - it must still be possible to move it
in and out for cleaning and servicing.
For safety reasons, curtains,must not be fitted immediately
behind the cooker.
A clearance of 130mm is required if the cooker is near a
corner of the kitchen, to allow the oven doors to open. The
actual opening of the doors is slightly less, but this allows
for some protection of your hand as you open the door.
To help you, there are two levelling rollers at the back,
and two screw-down levelling feet at the front. You
will need the levelling tool.
Remove the polystyrene base pack. From the front, tilt
the cooker forward and remove the front half of the
polystyrene base:
Repeat from the back and remove the rear half of the
polystyrene base.
Lowering the Two Rear Rollers
Firstly, fit the levelling tool on the hexagonal adjusting
nut, as shown below:
Make 10 complete (360º) turns clockwise. (This means
turning and removing the levelling tool 20 times).
23
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Do not use the door handles or control knobs to
manoeuvre the cooker.
Repositioning the Cooker following
Connection
If you need to move the cooker once it has been
connected, then you need to unplug it and, having
gripped under the fascia panel and lifted the front
of the cooker slightly (as shown above), you need to
check behind the cooker to ensure that the gas hose is
not caught. As you progress, make sure that both the
electricity cable and gas hose always have sufficient
slack to allow the cooker to move.
Make sure you lower BOTH REAR ROLLERS. There are
two adjusting nuts, one for each roller, at both the front
bottom corners of the cooker.
Unfold the rear edge of the pack base tray. Open the
grill door and right hand oven door so that you can get
a good grip on the bottom of the fascia panel as you
move the oven:
Release the stability chain as you ease the cooker
out. When you replace the cooker, don’t forget to refit
the chain and also check behind to make sure that the
electricity cable and gas hose are not caught or trapped.
Conversion to LP
If the appliance is to be converted to LP gas, carry out
the conversion at this point. See the conversion section
of these instructions.
Levelling
It is recommended that you use a spirit level on a shelf
in one of the ovens to check for level. Ensure that the
cooker in its intended position, taking care not to twist
it within the gap between the kitchen units, as damage
may occur to the cooker or the units. The front feet
and rear rollers can be adjusted to level the cooker.
To adjust the height of the rear of the cooker, use the
levelling tool supplied to turn the adjusting nuts at the
front bottom corners of the cooker. To set the front feet,
simply turn the bases to raise or lower them.
Leave the levelling tool with the customer, so that
they can use it if they wish to move the cooker again.
Grip under the fascia panel and lift the front of the
cooker slightly:
Fitting the Handles and Front Handrail
Remove the 4mm Allen screws from the doors with
the hexagon key tool. Use the screws to fit the door
handles.
The handles should be above the fixings.
Carefully push the cooker backwards off the pack base.
Remove the pack base tray. Position the cooker close
to its final position, leaving just enough space to get
behind it.
24
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Fit the plastic blanking plugs to the fixing holes.
Remove the 4mm Allen screws from the top corners of
the fascia and fix the front handrail in position.
Fitting the Splashback
The cooker can be installed with or without the
supplied splashback. To fit the splashback, remove the
two fixing screws (3mm hexagonal socket head) and
nuts that pass through the top of the rear flue grille.
Hold the splashback in position. From the rear, refit the
two fixing screws and nuts.
Fitting the Stability Bracket
The stability bracket supplied with the cooker must be
fitted. Read the leaflet supplied with the bracket, and fit
it as follows:
1.
2.
3.
4.
5.
6.
Place the cooker in its intended position and level the
cooker.
Draw a pencil line 70mm from the front edge of the
levelling feet.
Mark the centre line for the bracket by measuring
550mm from the left hand side of the cooker.
Move the cooker forward.
Measure back from the pencil line 500mm to locate
the front edge of the bracket. Position the bracket so
that it is away from centreline of the cooker to reduce
the possibility that it will trap the electrical connection
cable or gas hose. Fix the bracket to the floor.
Measure the height from floor level to the engagement
edge at the rear of the cooker. Add 3mm to this
dimension and assemble the stability bracket to this
height (i.e. from floor level to the underside of the top
member), and ensure the bracket does not foul the
oven burner assembly:
25
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Fitting the Restraining Chain
Hook the other end of the chain to the wall fixing:
The restraining chain must be fitted.
The length of chain between the appliance and the wall
fixing should prevent strain on the gas and electricity
connections, but still allow access to unhook the chain
when the cooker is pull forward.
Gas Connection
The Gas supply needs to terminate with a down facing
bayonet. The rear cover boxes limit the position of the
supply point.
Fix the supplied hook securely to the wall.
Measure the length of chain required. Use the hexagonheaded screw, washers and bolt supplied in the
restraining chain kit to fix the chain to one of the holes
at the top of the flue trim bracket:
View from the rear
A Position for gas supply connector
B Appliance gas inlet
���������
�������
�����
��������
Because the height of the cooker can be adjusted
and each connection is different, it is difficult to
give precise dimensions. Ideally, the house supply
connection should be in the shaded area shown in
the above diagram. A means of isolation must be
provided at the supply point by either an approved
quick-connect device or a Type 1 manual shut-off
valve. The hose should be fitted so that both inlet and
outlet connections are vertical so that the hose hangs
downwards in a ‘U’ shape.
The connector is located below the hotplate level at the
rear of the cooker.
A flexible connection is supplied with the cooker, and
it is with this in mind that the stability bracket and
restraining chain have been supplied.
If it is necessary to use another hose, it must be to A.S.
1869 Class B standard and suitable for your gas type
(if in doubt, contact your supplier). Even if you do use
26
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
another hose, it is still mandatory to fit the stability
bracket and restraining chain.
Jets
Standard burner
Wok burner
After completing the gas connection, ensure that
the cooker is gas sound with a pressure test (see the
following sections).
When checking for gas leaks, do not use washing up
liquid - this can corrode. Use a product specifically
manufactured for leak detection.
Natural Gas
The adjustable spring loaded governor is pre-set to give
a nominal pressure of 1kPa on NG. Connect to the Rp
1/2 inlet on the underside of the governor (just above B
on the previous figure).
Remove the burner caps and heads. Remove the old jets
and then fit the new jets. Re-assemble in reverse order.
Pressure testing for Natural Gas
Tap Adjustment
Pull the cooker forward, if necessary, to gain access to
the rear of the cooker. The gas pressure test point is
accessible on the connector block that comes out of the
governor at the top rear of the cooker.
Remove the test nipple screw and fit a pressure gauge
to the test point. Turn on and light two of the hotplate
burners.
See the data badge and the Technical Data section at
the back of this book for test pressures.
Conversion from Natural Gas to
LP Gas
Check in the Technical Data section at the back of
the book that the cooker is convertible to the type
of LPG (Liquid Petroleum Gas) that you want to use,
typically Propane.
This cooker is supplied ready for use on natural gas.
A conversion kit for propane gas is supplied with the
cooker. Any conversion to propane must be performed
by a competent person. Following conversion, the
installation must comply with the relevant regulations
and also the local electricity supply company
requirements.
A jet, B internal injector, C external injector
Pull off all the control knobs.
If the hand rail has
been fitted, remove it
by removing the plastic
blanking plugs, followed by
the two end bracket fixing
screws.
Remove the two crossheaded screws that were
hidden by the hand rail
end brackets.
Open the oven door and grill door and remove the
fixing screws underneath the control panel.
Lower the fascia panel clear of the top retaining tags.
Turn the bypass screw on each gas control clockwise to
the stop:
Read the instructions before converting the
appliance. Failure to convert the appliance correctly
could invalidate any warranty or liability claims and
lead to prosecution.
Before servicing or replacing gas-carrying
components, disconnect the cooker from the gas
connection before commencing operation. You
should also disconnect it from the electricity supply
to allow the servicing of items that connect to the
electricity supply, e.g. the fascia panel.
A tap bypass screw
Set the Governor
Unscrew the governor's brass top. There is a plastic
snap-in converter device in the base of the brass top:
Do not use re-conditioned or unauthorised gas
controls.
27
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Electrical Connection
This appliance must be installed by a qualified
electrician to comply with the relevant regulations
(in particular AS/NZS 60335.2.6:2002), and also the
local electricity supply company requirements.
�
To convert the governor, snap the device out of the
top and refit it the other way up. The snap-in converter
device is marked to show the gas for which it is set:
Natural gas
Propane gas
Make sure the device is secure in the top cap and refit
the cap to the governor.
Ensure that the mains characteristics (voltage, nominal,
power, etc.) match the ratings indicated on the data
plate affixed to the cooker.
Stick on label
Stick the appropriate label on to the data badge to
indicate the gas for which the appliance is now set.
Propane Pressure Testing
Connect the appliance to the gas supply. Ensure that the
appliance is gas sound.
The gas pressure can be measured at one of the left
hand hotplate burner jets. Lift off a burner head. Fit the
pressure gauge to the jet. Turn on the hotplate burner
and turn on and light one of the other burners.
Re-assemble the burner top, making sure that it is reassembled in the correct way on the burner body.
Refit the control tap shield. Reconnect the wiring to the
control panel and refit the panel.
Check that the appliance is both electrically safe and
gas sound.
Check the operation of all the burners.
The cooker is preset for a single-phase earthed electrical
connection. It is essential to install a multi-pole circuit
breaker that completely disconnects the appliance from
the mains, with a minimum contact break distance of
3mm.
WARNING: THIS APPLIANCE MUST BE EARTHED
The appliance must be connected to an efficient
earthing circuit. If the electricity network is not
equipped with an earth connection, then it must
be installed separately in compliance with local
regulations.
Earthing is a safety measure required by law,
and must be performed with particular care by a
qualified technician, who must also check that the
electricity supply characteristics are correct.
The cable size used should be suitable for the appliance
load and in accordance with local regulations. Please
note that the maximum cable sizes are 6mm2 for the
screw terminals.
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect
the mains cable to the correct terminals for your
electrical supply type.
You may need to move the links to suit your connection
type. Check that the links are correctly fitted and that
the terminal screws are tight. Secure the mains cable
using the cable clamp.
28
Australia
INSTALLATION
Check the appliance is electrically safe and gas sound when you have finished.
Each burner has an FSD (Flame Security Device) that will
stop the flow of gas if the flame goes out.
For each burner, press the ignition switch on the fascia
panel and push in and turn the knob to the solid flame
symbol ( ).
Keep holding the knob pressed in to let the gas through
to the burner for few seconds. If, when you let go of the
control knob, the burner goes out, then you have not
bypassed the safety device for initial ignition. Turn the
control to the off position and wait one minute, then try
again, this time holding in the control knob for slightly
longer.
Grill
Open the grill compartment door. Turn on the grill
control and check that the grill heats up.
Oven Check
Set the clock to the time of day. See 'The Clock' section
in the Users section of these instructions.
This shows the single-phase connection.
Fixed Wiring
For connection to fixed wiring, i.e. flexible conduit,
remove the electrical terminal cover box on the back
panel. Remove two screws and blanking plate from
the bottom flange of the cover box, so as to allow the
conduit through.
Turn on the ovens and check that the oven fans start to
turn. Turn off the ovens.
Fitting the Plinth
Loosen the three screws along the front bottom edge
of the cooker. Hook the central keyhole over the
central screw. Twist and fit each end keyhole over their
respective screws. Tighten the fixing screws.
Customer Care
Please complete your details in this Guide, make sure
that the user knows how to operate the cooker, and
hand over the Instructions.
Thank you.
Fix the conduit-to-conduit mounting bracket on the
back panel. Connect the mains cable to the correct
terminals for your electrical supply type. Check that the
links are correctly fitted and that the terminal screws are
tight.
Replace the electric terminal cover box, making sure
that the conduit is clear of the bottom flange.
Main Oven Light
Press the light switch in the main oven and check that
the light is working.
NB. The oven light bulb is not included in the
guarantee.
Hotplate
Check each burner in turn.
29
Australia
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Servicing Notes
Before servicing or replacing gas carrying components,
disconnect the cooker from the gas supply, and check that
the appliance is gas sound following completion.
Likewise, before servicing or replacing components that
are connected to the electricity supply, particularly before
removing the control panel, side panels, cooktop tray, or
any of the electrical components or cover boxes, disconnect
the cooker from this supply, and check that the appliance is
electrically safe prior to reconnection.
CAUTION: DO NOT USE A FLAME TO CHECK FOR GAS
LEAKS.
A Cooktop front fixing screws
B Cooktop rear fixing screws (on cooker back)
1. To Remove the Hand Rail
Remove the handrail plastic blanking plugs and remove
the two end bracket fixing screws.
Remove the two rear cooktop fixing screws (B) on the
cooker back under the flue grille, and the four front cooktop
fixing screws (A).
Remove the screws holding the flue grille stays.
Lift the cooktop clear of the appliance. Replace in reverse
order.
Re-assemble in reverse order, ensuring that the leads are
reconnected.
Check for correct burner operation.
2. To Remove the Control Panel
Pull off all the control knobs. Remove the hand rail (see
section 1) Remove the two cross headed screws that were
hidden by the hand rail end brackets.
4. To Remove a Side Panel
Open the grill door and right hand oven door and remove
the two screws underneath the control panel.
5. To Replace the Main Oven Light Switch
Remove the control panel (see section 2). Pull the cooker
forward. Remove the four retaining screws from each
panel (two at the front and two at the rear). The lower front
retaining screws (one each side) are situated beneath the
lower edge at the front corners of the side panels
Re-assemble in reverse order.
Remove the control panel (see section 2).
NB The old switch may be destroyed during removal.
Remove the switch button and old switch from its bezel
by gripping the switch body behind the control panel and
twisting sharply.
The switch bezel can then be removed by folding back its
locking wings and pushing forward. Fit the new bezel to the
control panel by first lining up the raised key on its body
with the cutout in the control panel and pushing it in from
the front. Assemble the new switch to the bezel by lining up
the key sections and pushing home. Fit the new button by
pushing in from the front.
Replace the control panel and test for correct operation.
Pull the control panel forward and support so that the wires
are not strained.
Re-assemble in reverse order. When replacing leads, refer
to the wiring diagram. Check the operation of the timer,
ignition, and oven light switches.
3. To Remove the Hotplate Top
Remove the pan supports, cooktop burner caps and tops.
If there are screws holding the cooktop burners to the
cooktop, remove them (but not the spark electrode fixing
screws).
6. To Replace the Electronic Timer
Pull off the timer control buttons and remove the control
panel (see section 2). Remove the timer/mounting bracket
assembly from the control panel by removing the two fixing
screws. Remove the timer from its mounting bracket by
depressing the plastic lugs on the timer case, at the same
time pulling the unit forward.
Re-assemble in reverse order. When replacing the leads,
refer to the wiring diagram. Check the operation of the
timer.
30
Australia
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
7. To Replace a Thermostat
thumb and forefinger. Pull off the electrode, but keep
hold of the lead. Fit the new electrode to the lead. Fix the
electrode in the burner with the screw. Replace the burner
cap. Check the burner ignition. Replace the pan supports.
Remove the control panel (see section 2) and hotplate
top (see section 3). Open the appropriate oven door and
remove the oven shelves.
Right hand oven
Remove the oven roof. Remove the two fixings that secure
the thermostat phial cover. Unclip the thermostat phial
from the clips in the oven back panel and remove it from
the top rear of the oven.
12. To Remove or Change a Hotplate Burner.
Remove the hotplate top (see section 3). Remove the
control panel (see section 2).
Outer Hotplate Burners
The burners are mounted in two’s on cross supports.
Disconnect the burner feed pipes at the burners. Remove
the screw at the front holding the cross support. Slide the
support to the right to release it from the rear location.
Left hand oven
Remove the two screws holding the thermostat phial to the
oven fan cover at the rear of the oven. Pull the unit forward
to access the rear of the cooker. Remove both rear cover
boxes by removing the fixing screws and lifting clear.
Feed the thermostat capillary clear of the oven. Disconnect
the wires from the thermostat and undo the two fixings
that secure the control to the mounting plate. Fit the
replacement and re-assemble in reverse order. Ensure that
the phial is clipped to the oven rear, positioned centrally
between the clips. Check that the thermostat functions
correctly.
8. To Replace the Grill Controller
Remove the control panel (see section 2) and hotplate top
(see section 3). Disconnect the wiring from the controller.
Remove the two screws holding the switch/controller to
mounting panel. Fit the new controller and re-assemble in
reverse order. Check for correct operation.
Lift the cross support and burners clear. The burners
are fixed to the cross supports with screws underneath.
Remove the appropriate burner and fit the new one.
Re-assemble in reverse order. Check that the burner
operation is satisfactory.
9. To Change a Hotplate Tap
Remove the hotplate top (see section 3). Unplug the FSD
lead from the rear of the tap. Undo the compression fitting
at the rear of the tap. Remove the fixings that secure the
tap to the gas rail. Remove the tap. Remove and discard the
gasket seal. Fit the new gasket seal to the replacement tap.
Re-assemble in reverse order.
Ensure that the valve is adjusted for correct gas operation.
Check that the cooker is gas sound. Check hotplate ignition.
10. To Replace a Hotpate Burner Jet
Wok burners
Disconnect the burner feed pipes at the burner. Fit the new
one and re-assemble in reverse order. Check that the burner
operation is satisfactory.
13. To Remove the Grill Outer Door Panel
Open the left hand oven door and remove the two screws
from the bottom edge of the grill door.
Open the grill door, support grill door outer panel, and
remove the two screws from the top inner face of the grill
door.
Re-assemble in reverse order.
14. To Remove an Oven Door
Open the oven door and remove the Handyrack (where
fitted) by springing one side out of the bracket on the door
and sliding the other side free. The door is heavy - take care.
Open the oven door and loosen the two top hinge screws.
Remove the burner cap and head. Remove the old jet. Fit
the new orifice.
NB The Wok burner has 2 orifices.
Re-assemble in reverse order. Check that the appliance is
gas sound.
11. To Change a Hotplate Burner Electrode
Lift off the cooktop pan supports and remove the burner
cap. Remove the screw holding the electrode. Pull the
electrode vertically up sufficiently to grip the lead between
31
Australia
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Support the weight of the door and remove the screw
nearest the hinge pin. Swing the hinge up and away from
the hinge pin on the door.
Lift the door away from the bottom hinge.
Re-assemble in reverse order.
When replacing the door, ensure that the nylon hinge bush
is in position between the hinge pin and the hinge bracket
at the both the bottom and top.
16. To Change the Main Oven Door Catch
Remove the outer door panel (see section 15). Remove
screws ‘B’ holding the catch assembly to the inner door
panel. Fit the new catch and re-assemble in reverse order.
15. To Change the Main Oven Door Outer Panel
Verify that the door operation is correct.
Remove the two plastic blanking plugs from the door
handles. Remove the four 4mm Hex headed screws holding
the handle to the door with the hexagon key tool. Remove
two screws from the top edge, and two from the bottom
edge, of the door:
17. To Adjust the Main Oven Door Catch Keep
Open the Main oven door, slacken off the locknut at the
base of keep, and screw in or out as required until the
required fit is obtained:
Retighten the locking nut.
Remove the outer door panel. Fit the door handle to the
new panel. Fit the plastic blanking plugs to the fixing holes.
18. To Replace the Tall Oven Door Outer Panel
Remove the oven door (see section 14). Lay the door face
down on a suitable surface and remove the two screws
from the bottom edge of door and the two screws from
the inside face of the door.
Remove the outer door panel. Remove the door handle
by unscrewing the two screws.
Remove the two cross-headed screws holding the door
handle fixing bracket to the door panel. Fit the door
handle bracket and the door handle to the new panel.
Fit the panel to the door and re-assemble in reverse
order.
The handles should be above the fixings.
Fit the panel to the door. If replacing the outer panel on the
right hand door (with the Thermodial) take care to make
sure that the sensor of the Thermodial is sealed to the door
by the rubber grommet:
19. To Replace the Tall Oven Door Magnetic Latch
Remove the control panel (see section 2). Remove the
plinth (three screws) and the central vertical cover (five
screws). Prize the retaining clip off the magnet unit.
Fit the new unit and retaining clip, and re-assemble in
reverse order. Verify that the door operation is correct.
20. To Change an Oven Door Seal
Open the oven door. The seal is held in place by small hooks
on the rear face. At the corner, pull the seal diagonally away
from the door centre until that hook is released. Proceed to
the next hook and release it in a similar way, and so on.
Re-assemble in reverse order.
32
Australia
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
24. To Replace an Oven Fan Element
Remove the oven inner back as detailed in section 22.
Remove the fixings that secure the element within the oven
and lift the element away carefully.
When fitting the new seal, position the seal join at the
bottom. Hook the new seal in one of the corner holes of the
door, and proceed round the door snapping in each hook
in turn.
Disconnect the leads and connect to the replacement
element. Re-assemble the parts in reverse order. Check that
the oven operates correctly.
21. To Change Ignition Generator
Pull the cooker forward to gain access to the cover box at
the rear of the left hand oven. Remove the screws securing
the cover and lift clear. Pull off all the leads to the generator,
noting their positions. Slacken the two screws holding the
generator to the cooker and remove the generator.
Fit the new generator to the cooker and replace the leads,
referring to the wiring diagram. Re-assemble in reverse
order. Check ignition performance.
25. To Remove Grill Element
Remove the grill pan from the grill chamber. From
inside the grill compartment, remove the enamelled
front shield from the grill roof, and the two screws and
washers.
Remove the two screws and washers securing the grill
element front support. Remove one screw from each of
the grill elements and withdraw the grill element from
the grill chamber.
Disconnect the leads and connect to the replacement
elements. Re-assemble the parts in reverse order. Check
the operation of the grill.
22. To Remove an Oven Inner Back
Open the oven door and remove the oven furniture.
Unscrew the two thermostat phial fixing screws (see section
7). Remove the fixings that secure the inner back to the
oven rear:
26 To Remove the Left hand Oven Bottom and Top
Elements
Bottom Element
Pull the cooker forward to access the cover boxes at the rear
of the unit. Remove the fixings that secure the cover and lift
it clear.
Lift the removable panel away. Re-assemble in reverse
order, ensuring that the retaining fixings are fully tightened.
23. To Replace an Oven Fan
Pull the unit forward to access the cover boxes at the rear of
the appliance. Remove the fixings that secure the cover and
lift it clear. Remove the fan wiring, noting the connection
positions. Remove the inner back as detailed in section
22. Hold the fan blades and undo the centre nut (left hand
thread), brass washers, fan blade and Circlip. Undo the
fixings that retain the fan and remove it from the cavity rear.
Fit the replacement and re-assemble parts in reverse order.
Check that the oven operates satisfactorily.
Remove the two screws ‘A’ and allow the plate to drop
down.
33
Australia
SERVICING - WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
Remove the two screws B, holding the element to the
bottom sheet.
Disconnect the leads, noting their positions.
Withdraw bottom element. Fit the new element and reassemble parts in reverse order.
Top Element
Open the left hand oven door and undo the fixings that
secure the heat shield. Remove the top element bracket
fixings and withdraw the element.
Replace the element and re-assemble the parts in reverse
order. Check that the oven operates satisfactorily.
24 To Adjust the Main Oven Door Angle
The Main Oven door bottom hinge can be adjusted to
alter the angle of the door. Loosen the bottom hinge
fixing screws and use the notch and a flat bladed
screwdriver to move the position of the hinge to set the
hinge position.
Retighten the hinge screws.
Effect of hinge adjustment – exaggerated for clarity
Centre line of hinge pin
Oven door omitted for clarityCircuit Diagram
34
Australia
Circuit Diagram
35
Australia
Technical Data
This cooker is designed for use on Natural Gas, although a conversion for LP (LPG X Propane (2.54kPa)) gas is
available.
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Cooker back. The serial number is repeated on the badge below the left hand oven door
opening.
Country of Destination: Australia
Test Pressures (quoted on the data badge)
Gas
Natural gas
Propane
Electric
220 - 240V 50Hz
1kPa
2.54kPa
Dimensions
minimum 893mm
900mm
648mm
650mm
Overall height
Overall width
Overall depth
Minimum space above hotplate
maximum 920mm
Connections
Gas:
Electric
Rp 1/2 at rear right
220 - 240V 50Hz
Ratings
Hotplate
Natural Gas 1.0kPa
Injector
Bypass
Input
Marking
Size
Wok burner
15MJh-1
internal 112 1.12mm
external 164 1.65mm
Large Burner
Medium Burners
Small Burner
12.3MJh-1 165
6.2MJh-1 115
3.7MJh-1 92
1.65mm
1.15mm
0.92mm
Propane 2.54kPa
Injector
Marking Input
90
15MJh-1
80
56
48
12.3MJh-1
6.2MJh-1
3.3MJh-1
Bypass
Marking
Size
internal 66
external
91
89
67
48
0.67mm
0.87mm 54
0.96mm 41
0.68mm 33
0.50mm 25
Gas burner inputs based on Gross Calorific Value
Ovens
Left hand Multi-function Oven
Right hand Fan Oven
Fan element
Top element
Browning Element
Bottom element
2.5kW
1.2kW
1.15kW
1.0kW
2.3kW
2.5kW
Grill
Maximum total electrical load at 230V 7.4kW (approximate total including oven lights, oven fan etc.).
36
Marking
Australia
37
Australia
38
Australia
39