Eureka 5550 Series Specifications

®
Upright
Vacuum Cleaner
Household Type
Owner’s Guide
5550 Series
IMPORTANT
Do not return this product to the
store.
For assembly problems or questions and
replacement of broken or missing items
contact: Eureka’s Customer Service Division
toll free at 1-800-282-2886*, 8 a.m. to 7:30
p.m., (CST), Monday - Friday and 10 a.m. to
6:30 p.m. Saturday.
To order replacement parts and accessories
contact Eureka’s Customer Service Division
toll free at 1-800-282-2886*, 8 a.m. to 7:30 p.m.,
(CST), Monday - Friday and 10 a.m. to 6:30 p.m.
Saturday, or visit our web site,
www.eureka.com.
*En Mexico llame al 5670-6169.
Index
Important Information 2-3
Assemble .................... 5
Use .............................. 7
Accessories ................. 9
How to Remove
Blockages ................. 10
Brush Roll ................. 11
Brush Roll Belt .......... 11
Filter .......................... 12
Dust Cup ................... 13
Warranty .................... 16
Part No.73657 (12/03)
Please Retain
We suggest you record the model, type and serial numbers
below. They are located on the silver rating plate on your cleaner.
For prompt and complete service information, always refer to
these numbers when inquiring about service.
Model & Type___________________________
Serial No. ______________________
It is also important to keep your receipt as proof of date of
purchase.
©2003 White Consolidated, Ltd.
Printed in U.S.A.
Vacuum Cleaner Safety
IMPORTANT SAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER.
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave vacuum cleaner when plugged in.
Turn off the switch and unplug the electrical cord
when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If vacuum
cleaner is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, have unit serviced before using.
• Do not pull or carry by cord, use cord as a handle,
close a door on cord, or pull cord around sharp
edges or corners. Do not run vacuum cleaner over
cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with
inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not unplug by pulling on cord. To unplug, grasp
the plug, not the cord.
• Do not handle plug or vacuum cleaner with wet
hands.
• Do not put any object into openings. Do not use
with any opening blocked; keep free of dust, lint,
hair, and anything that may reduce airflow.
• This vacuum cleaner creates suction and contains
a revolving brush roll. Keep hair, loose clothing,
fingers, and all parts of body away from openings
and moving parts.
• Do not place cleaner on furniture or stairs as the
brush roll may cause damage. Place cleaner on
floor with the handle in storage position while using
attachments.
• Do not pick up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
• Belt pulleys can become hot during normal use. To
prevent burns, avoid touching the belt pulley when
servicing the drive belt.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible
liquids such as gasoline, or use in areas where
they may be present.
• Store your cleaner indoors in a cool, dry area.
• Keep your work area well lighted.
• Unplug electrical appliances before vacuuming
them.
SAVE THESE INSTRUCTIONS
2
Conseils pour l’emploi correct de votre aspirateur
CONSEILS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent être observées, incluant les
suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique,
ou de blessure:
• Ne pas utiliser à l’extérieur ou sur des surfaces
mouillées.
• Ne pas laisser l’aspirateur seul quand il est
branché. Mettre l’interrupteur sur arrêt et
débrancher l’appareil lorsque vous ne l’utilisez pas
ou avant l’entretien.
• Ne permettez pas qu’il soit utilisé comme jouet.
Une attention particulière est nécessaire lorsque
utilisé par ou prés d’un enfant.
• Suivez les recommandations d’utilisation de ce
manuel. Utilisez uniquement les accessoires
recommandés par le fabriquant.
• Ne pas utiliser si le cordon ou la fiche sont
endommagés. Si l’aspirateur ne fonctionne pas
comme il le devrait, s’il a été échappé, s’il est
endommagé, s’il a été laissé à l’extérieur ou
échappé dans l’eau, retournez-le à un centre de
service avant d’utiliser.
• Ne pas le tirer ou le transporter par le cordon, ne
pas utiliser le cordon en guise de poignée. Ne pas
fermer une porte sur le cordon ou tirer le cordon
sur des coins ou bordures pointus. Ne pas circuler
sur le cordon avec l’aspirateur. Tenir le cordon à
distance des surfaces chauffantes.
• Ne pas utiliser des rallonges ou des prises qui n’ont
pas de capacité suffisante pour transporter le
courant.
• Fermer tous les contrôles avant de débrancher.
• Ne pas débrancher en tirant sur le cordon. Pour
débrancher, tenez la fiche et non le cordon.
• Ne pas manipuler la fiche ou l’aspirateur avec les
mains mouillées.
• Ne pas rien insérer dans les ouvertures. Ne pas
utiliser si des ouvertures sont bloquées; assurezvous qu’elles soient dégagées de poussière,
mousse, cheveux ou toute autre chose qui pourrait
réduire le passage de l’air.
• Cet aspirateur créé de la succion et contient un
rouleau-brosse tournant. Tenir les parties mobiles
et les ouvertures loin des cheveux, du linge, des
doigts et de toute partie du corps.
• Ne pas mettre l’aspirateur sur les meubles ou sur
les escaliers car le rouleau-brosse peut faire des
dommages. Placer l’aspirateur sur le plancher avec
le manche en entreposage position temps que les
accessoires sont en usage.
• Ne pas ramasser des objets qui brûlent ou fument
comme les cigarettes, allumettes ou cendres
chaudes.
• Les poulies du courroie peuvent devenir chaudes
pendant l’utilisation normale. Pour prévenir des
brûlures, évitez de touché la poulie du courroie
lorsque vous réparez la courroie.
• Portez une attention particulière lorsque vous
nettoyez les escaliers.
• Ne pas utiliser pour ramasser des liquides
inflammables ou combustibles comme de
l’essence: Ne pas utiliser dans les endroits où ces
liquides pourraient être présents.
• Entreposez votre aspirateur à l’intérieur dans un
endroit propre et sec.
• Maintenez un bon éclairage à l’endroit où vous
travaillez.
• Débrancher les appareils électrique avant de les
balayer.
CONSERVEZ CES INSTRUCTIONS
3
To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée (une des lames est plus
large). Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être
insérée dans la prise, retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer
une prise adéquate par un électricien qualifié. Ne pas modifier la fiche.
General Information
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner
to prevent hose clogs.
DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and
sealed.
Customer Assistance
The instructions in this booklet serve as a guide to routine maintenance. For additional service information please
call, 1-800-282-2886. You should know the model, type and serial numbers when you call.
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the
cleaner suddenly shuts off, turn the switch off and unplug the cleaner. Check the cleaner for a possible source of
overheating such as a blocked hose or clogged filters. If these conditions are found, fix them and wait at least 30
minutes before attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the
switch. If the cleaner still does not run, then call 1-800-282-2886 for customer assistance.
4
How To Assemble
CAUTION: Assemble the cleaner completely before plugging into an electrical outlet.
CAUTION: Moving parts, stay clear of brush roll when plugging in.
NOTE: Features may vary by model yet all parts assemble the same.
Step A Remove Dust Cup
Step B Attach Handle
NOTE: Screws must be installed to properly
secure the handle.
Dust
Cup
Latch
Handle
Tabs
Dust Cup
Handle
Slots
Two Screw Locations
Screw
Screw
Dust Cup
1. Remove dust cup from unit to expose the two
screw installation locations. Release the dust cup
by rotating the dust cup latch to the left. Pull out
and up on the dust cup handle to remove from
unit.
2. Position handle as above. Slide the handle down
over the top of the unit, inserting handle tabs into
slots on unit.
3. Find the two screws in the accessory bag
included in the carton. To secure the handle on
the unit, install the two screws.
5
Step C Replace Dust Cup
Dust Cup
Latch
Step D Store Accessories
Dusting/
Upholstery
Brush
Nesting
Extension
Wands
(shipped
stored on
cleaner)
Crevice
Tool
Groove
4. Replace dust cup by aligning front of the bottom
of dust cup into groove on cleaner. Pivot dust cup
up against cleaner and rotate the dust cup latch
to the right to secure.
Step E Store Electrical Cord
5
Cord
Retainer
5.
You will find your cord retainer on the handle
above the upper cord hook. Firmly push the
electrical cord down into the cord retainer. This
will place the cord out of the way the next time
you vacuum.
6.
Next wind the cord around the two cord hooks
on the back of the cleaner.
7.
Secure the plug to the cord to prevent
unwinding.
6
Cord
Hook
6
Cord
Hook
6
How To Use
1. Cord Retainer. To use, push electrical cord down into cord
retainer.
CAUTION: Do not plug in cleaner until you
2. ON/OFF Switch. International symbol I means On,
International symbol O means Off.
understand all controls and
features.
3. Dust Cup Latch. When dust cup latch is pointing to the left,
the dust cup compartment is unlocked. When dust cup latch
is pointing to the right the dust cup is locked in place. See the
locked/unlocked symbols on the unit.
4. HEPA Filter Compartment. To open, slide HEPA filter door
up and pull away from unit. To close, place HEPA filter door at
top of opening pressing against unit, slide down into place.
5. Dust Cup Handle. Use the handle to remove and replace
the dust cup in the dust cup compartment.
1
6. Dust Cup Compartment. To open, turn dust cup latch (3) to
the left pointing to unlock symbol, then grasp dust cup handle
(5) and pull dust cup out and away from unit. To close, place
the front of the bottom of the dust cup in groove at the bottom
of dust cup compartment, rotating dust cup up and against
unit. Then turn dust cup latch to the right pointing to the lock
symbol.
2
7. Stair Handle. To use when cleaning stairs.
8. Handle Release. Step on handle release. Pull handle back
to a comfortable position. Press release again to lower handle
further to clean under furniture.
3
9. Light Bulb Compartment. To gain access to light bulb
compartment remove the two screws in the lens.
10. Brush Roll Belt Window. To check condition of belt watch
to see if white dots on belt are moving through the window.
This indicates the brush roll is turning.
4
11. Screws to Release Hood. Remove these screws to release
hood and give access to brush roll belt area.
5
12. Cleaner Height Setting. The front of the cleaner has an
adjustment that raises or lowers the cleaner base to match
the type of floor surface. With the cleaner cord unplugged,
set the adjustment to lowest setting for maximum carpet
cleaning. If the cleaner is difficult to push, move adjustment
to next highest setting until cleaner is comfortable to push.
The brush roll must reach the carpet for effective cleaning.
For ease in moving the adjustment knob, place handle in
operating position and tilt cleaner back to remove weight from
front wheels.
13
6
7
8
9
11
10
11
12
WARNING: Avoid injury. Keep loose clothing, hair,
fingers, and all other parts of body away from
any moving part (such as the revolving
brush). Turn off the switch and unplug the
cleaner before changing the cleaner height
setting.
13. Extension Wands. Use these wands on the end of the hose
for added cleaning reach.
7
How To Use (continued)
14. Hose Retainers (3). Place hose on retainers to
store hose on unit.
15. Carrying Handle. Use this handle to carry unit
from one place to another.
16. Dusting/Upholstery Brush. Store dusting brush
here.
17. Electrical Cord Hooks (2). Wrap electrical cord
around them to store electrical cord on unit. Top
hook rotates down for quick release of the
electrical cord. Rotate back up to store electrical
cord.
14
18. Clear Tube Quarter Turn Fastener. Turn this
fastener to the unlock position to remove the clear
tube. To replace tube, place tube on the back of
the unit and turn fastener to lock position.
15
19. Crevice Tool. Store crevice tool here.
20. Hose Adapter. Place the end of the hose into hose
adapter for floor/carpet cleaning.
16
17
18
14
Thermal Cut Off
19
14
This cleaner has a special thermostat that
protects the cleaner in case of motor overheating.
If the cleaner suddenly turns off, follow this
procedure:
17
20
8
1. Push on/off switch to off.
2. Unplug cleaner.
3. Check for source of overheating problem (i.e. full
dust cup, clogged hose or clogged filters).
4. If a full dust cup, clogged hose or clogged filters
are found, empty the dust cup, unclog the hose or
replace the filters.
5. Wait at least 30 minutes before attempting to reuse
the cleaner.
6. After 30 minute cool down period, plug the cleaner
in and push the switch pedal. The cleaner should
turn on.
7. If the cleaner still does not operate, call 1-800-2822886 for customer assistance.
How To Use Accessories
CAUTION: Do not place cleaner on furniture or steps as the brush roll may cause damage. Place cleaner on floor
with the handle in storage position while using accessories.
1. Remove hose from hose adapter on the
back of cleaner.
Dusting/Upholstery Brush is for furniture, blinds, books, lamp
shades, shelves, curtains, draperies, cushions and fabrics.
2. Place desired accessory onto end of hose
or wand.
Dusting/
Upholstery
Brush
Crevice
Tool
Hose or
Wand
Crevice Tool cleans corners, baseboards, between cushions.
Hose
Adapter
Extension wands (Some models use 1 wand)
Nested extension wands to add reach.
• Grasp both wands near ridges.
• Pull apart.
• Turn ridge end to center.
• Push wands together.
9
How to Check and Clear Hose Blockages
Low suction or poor pickup may be due to a blockage in
the vacuum cleaner.
1. Remove hose from hose retainer and check suction at
end of hose - if little or no suction, check dust cup. Empty
if needed. If no improvement, proceed to step 2.
Electrical
Cord
CAUTION: Turn off the switch and unplug the electrical
cord before clearing hose.
2. Remove electrical cord from cord hooks. Disconnect the
clear tube by turning quarter turn fastener to the right to
release, then lift away from cleaner.
Hose Retainer
Check for any obstructions that may be in the tube. Any
obstructions can be removed by using a blunt instrument
to clear the tube.
1
3. To completely release hose from the unit, remove two
screws.
1. Remove hose from hose retainer and
check suction at end of hose.
Any obstructions can be removed by using a blunt
instrument to clear the hose. Flexing the hose may help
loosen the blockage.
After clearing blockage, reverse above steps to
reassemble unit.
Quarter Turn
Fastener
Two Screws
3
2
Clear
Tube
2. Disconnect clear tube.
10
3. Release hose from unit.
How To Maintain
The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls,
check the dust cup, belt, and brush roll often.
Brush Roll
The brush roll turns as it sweeps and combs the carpet nap. Remove hair and threads from the brush roll so it
continues brushing the carpet. To maintain the most efficient cleaning, the bristles must touch the carpet. To test
the bristle length, hold a ruler against the underneath side of the cleaner. If the bristles no longer touch the ruler,
replace the brush roll.
Brush Roll Belt
The brush roll belt turns the brush roll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be
sure it is in good condition. Replace the belt if it stretches, cracks or loses tension. Cut away any hair or threads
wound around the brush roll or the belt pulley because the buildup could cause the belt to rotate unevenly.
How To Replace Brush Roll Belt – Style U
CAUTION: Turn off the switch and unplug the electrical cord before replacing belt. Belt pulleys can
become hot during normal use. To prevent injury, avoid touching the motor pulley when
checking the belt.
4
Motor
Shaft
1
Belt
Brush
Roll
3
2
1. Lower handle to floor to change belt.
3. Lift left end of brush roll.
2. Remove two screws to release hood. Lift hood to
remove.
4. Remove and discard belt.
5. Clean debris from brush roll area.
11
To Change Dust Cup Pleated Filter:
NOTE: Turn off the switch and unplug the electrical
cord before changing the Pleated Filter.
Never operate the vacuum cleaner without
the dust cup or the pleated filter assembly.
5
6. Place new belt around motor
shaft.
1
Dust Cup
Latch
6
7
7. Place belt around brush roll pulley.
8. Pull right side of brush roll to stretch belt. Secure
right end cap into base.
2
Dust Cup
8
Left side view
9. Align left end cap with square in base. Push end
cap into place; see left side view.
Release dust cup by rotating dust cup latch to the left
pointing to the unlock symbol ( ). Pivot dust cup out
and away from cleaner and remove.
9
10. Rotate brush roll to seat belt.
11. Replace the hood. Make sure hood front is behind
furniture guard.
12. Tighten screws.
Use replacement belt, Style U.
12
Remove cyclonic dust cup by pulling latch (1) forward,
pivoting cyclonic dust cup out and lifting up. To replace
cyclonic dust cup, put bottom of cyclonic dust cup in
place by aligning tabs in slots and pivot top assembly
back into place. Push down on latch (1), making certain
that latch securely snaps and overlaps tabs at top of
dust cup.
To maintain good performance, check and clean the
Pleated Filter each time the dust cup is emptied and
clean if needed. The filter can be cleaned by washing
with mild detergent and warm water. Be sure pleated
filter is completely dry before reinstalling.
To clean the Pleated Filter:
1. Remove the gray filter assembly by grasping handle and lifting upward and out of the dust cup.
2. Grasp the pleated filter and turn counter clockwise to remove.
3. Lift pleated filter from cone and wash. Shake excess water from filter. Do not submerge gray filter assembly
– wipe only with a damp cloth.
4. When all parts are completely dry, replace pleated and turn clockwise to lock in place.
Pleated
Filter
Gray Filter
Assembly
Use The Eureka brand replacement pleated filter, Style DCF-4, part number 62132.
FOR INSTRUCTIONS ON HOW TO REMOVE THE CYCLONIC DUST CUP FROM THE CLEANER BODY, REFER TO
PAGE 12.
Emptying the Cyclonic Dust Cup:
It is clearly visible when the dust compartment is full and needs emptying. Remove dust cup from cleaner body
and dump debris in a waste container.
Reinstalling the Cyclonic Dust Cup:
To mount gray filter assembly into cleaner body, make certain gray filter assembly is fully seated in top of dust
cup. Replace dust cup by aligning front of the bottom of dust cup into groove on cleaner. Pivot dust cup up against
cleaner and rotate the dust cup latch to the right to secure.
CAUTION:
The dust cup can be washed in warm water, if desired, but strong detergents should not be used. Dry
thoroughly before using again. Do not submerge gray filter assembly, wipe only with a damp
cloth.
13
Cleaning and Replacing Filters
HEPA Filter
Inspect the HEPA filter periodically and change as
needed. For maximum efficiency, replace the HEPA
filter periodically.
HEPA
Filter
To Replace HEPA Filter
1. Push down on latch and pull out on HEPA filter
door to remove.
2. Grasp filter and pull out.
Latch
HEPA
Filter
Door
3. Place new HEPA filter into cleaner.
4. To close, place HEPA filter door on top of bottom
tab, pivot door up and press door against cleaner
until it latches.
Use replacement HEPA filter supplied, Style GE1, part
number, 62134..
How To Change Light Bulb
CAUTION: Turn off the power switch and
unplug the electrical cord before
changing light bulb.
1. Lower handle to remove two screws from lens
cover.
2. Pull lens cover from cleaner.
3. Support socket with one hand and pull light
bulb straight out to release.
4. Place new light bulb into socket; push to
secure.
5. Push light bulb and socket back
so bulb will not touch lens cover.
6. Replace lens cover.
7. Secure with two screws.
Use replacement light bulb, 57940-3.
14
Lens
Cover
Problem Solving
NOTE: Turn off the switch and unplug the electrical cord before servicing.
PROBLEM
CAUSE
SOLUTION
Motor will not start.
✓
Electric Plug
Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
Motor suddenly stops.
✓
Thermal Cut Off
Refer to page 8.
Does not clean the carpet or
floor
✓
Dust Cup and Filter(s)
✓
✓
Belt
Brush Roll
✓
Hose
Empty the dust cup. Make sure the foam cone filter is
clean and installed properly. Make sure dust cup is
installed properly and dust cup latch secured.
Replace a cut, loose or out of shape belt.
Clean hair and thread from bristles and end cap area.
Replace brush roll if bristles are worn.
Remove any clogs from the hose that restrict the airflow.
✓
Dust Cup and Filter(s)
✓
Hose
Headlight not working.
✓
Light Bulb
Replace light bulb.
Noise from the brush roll area.
✓
✓
Brush Roll
Belt
Remove hood and clean debris from the brush roll area.
Replace a cut, loose or out of shape belt.
Cleaner is hard to push.
✓
Cleaner Height Setting
✓
Belt
Turn adjustment knob to a higher position. Hint: Put
handle in operating position. Tilt the cleaner back to
raise the front wheels off floor. Then turn the knob.
Replace a cut, loose and out of shape belt.
✓
✓
Brush Roll
Belt
Remove hood and clean debris from the brush roll area.
Replace cut, loose or out of shape belt.
Burning smell.
✓
✓
Brush Roll
Belt
Remove hood and clean debris from the brush roll area.
Replace cut, loose or out of shape belt.
Cleaning height knob will not
turn.
✓
Cleaner Height Setting
Hint: Put handle in operating position. Tilt the cleaner
back to raise the front wheels off floor. Then turn the
knob.
Missing parts or questions.
✓
No suction at the end of the
hose.
Brush roll will not turn.
Empty the dust cup. Make sure the foam cone filter is
clean and installed properly. Make sure dust cup is
installed properly and dust cup latch secured.
Remove any clogs from the hose that restrict the airflow.
Check both ends of the hose. (See pages 10)
Call 1-800-282-2886 for customer assistance.
15
THE EUREKA LIMITED WARRANTY
What This Warranty Covers
Your Eureka cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of one year. The warranty is granted only to the
original purchaser and members of his or her immediate household. The warranty is subject to the following provisions.
What This Warranty Does Not Cover
• Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, brush roll bristles, impellers and cleaning.
• Damages or malfunctions caused by negligence, abuse, or use not in accordance with the Owner’s Guide.
• Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts.
What The Eureka Company Will Do
The Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this warranty. As a matter of warranty policy, the Eureka Company
will not refund the consumer’s purchase price.
Warranty Registration
Please fill out and return the warranty registration card accompanying your cleaner.
Obtaining Warranty Service
To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station.
You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners–Service and Repair.” Be certain that the Warranty Station is “Eureka Authorized.”
For the location of the nearest Eureka Authorized Warranty Station or for service information visit www.eureka.com, or telephone toll free: USA: 1-800-282-2886, Mexico: 5670-6169,
Canada: 1-800-282-2886.
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company, 866 Langs Drive,
Cambridge, Ontario N3H 2N7.
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping charges to the Eureka Authorized Warranty Station.
Return shipping charges will be paid by the Warranty Station. When returning parts for repair, please include the model, type, and serial number from the data plate on the cleaner.
Further Limitations and Exclusions
Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of Merchantability or any warranty for Fitness For A Particular
Purpose is limited to the duration of this warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided above. In no event shall Eureka be liable for any consequential or incidental damages you
may incur in connection with your purchase or use of the cleaner. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary by state.
Questions & Answers about Genuine Eureka Products
Q: Why should I use only Genuine Eureka paper bags, belts, and parts in my Eureka vacuum cleaner?
A: Using Genuine Eureka Products, which are made to our exacting specifications and engineered with emphasis on quality, performance, and customer satisfaction, ensures the long life and cleaning
efficiency of your vacuum cleaner.
Q: How can I be sure I am using only genuine Eureka products in my vacuum cleaner?
A: Typically, packaged products and paper bags are labeled “Genuine Eureka Product”.
Q: Are there any differences between “made to fit” or “imitation” and Genuine Eureka paper bags, belts, and parts?
A: Yes, there are some very important differences in materials, quality, and reliability.
For Genuine Eureka Value, Accept No Imitations!
THE EUREKA COMPANY
Bloomington, Illinois 61701
19