SUPREMA1W/SS
DISHWASHER
BAUMATIC SUPREMA1W/SS dishwasher user manual
IMPORTANT!
PLEASE READ THIS MANUAL AND KEEP IT FOR FUTURE REFERENCE!
THIS MANUAL CONTAINS SECTIONS OF SAFETY INSTRUCTIONS, OPERATING
INSTRUCTIONS & TROUBLESHOOTING TIPS, ETC.
BAUMATIC
SUPREMA1W/SS – DISHWASHER
60CM FULL HEIGHT DISHWASHER
INSTRUCTION MANUAL
CAREFULLY READING IT BEFORE USING THE DISHWASHER WILL HELP
YOU USE AND MAINTAIN THE DISHWASHER PROPERLY.
DD 02/11/07
1
1
BAUMATIC SUPREMA1W/SS dishwasher user manual
2
CONTENTS
•
SAFETY FIRST!
SAFETY INFORMATION .……………..…………3
*Please read this before using your dishwasher!
•
BEFORE CALLING
FOR SERVICE
KNOWING YOUR
DISHWASHER
CONTROL PANEL ………………………..……..…4
DISHWASHER FEATURES …………..………….4
REVIEWING THE SECTION ON
TROUBLESHOOTING TIPS WILL
HELP YOU SOLVE SOME
COMMON PROBLEMS WITHOUT
THE NEED TO ASK FOR HELP
FROM PROFESSIONAL
TECHNICIANS.
•
USING YOUR
DISHWASHER
WATER SOFTENER …………………..………...5-6
DETERGENT ………………..............................6
RINSE AID ………………….............................7
LOADING YOUR DISHWASHER…..….......8-11
STARTING A WASH CYCLE ……………….12-14
UNLOADING AT THE END OF A CYCLE…....14
FILTERING SYSTEM ………………..…….…….15
CLEANING AND MAINTAINING
YOUR DISHWASHER …………………….…15-17
•
PLEASE NOTE:
BEFORE YOU CALL FOR
SERVICE…
TROUBLESHOOTING ………………….…18-21
ERROR CODES ………………………………….…22
THE MANUFACTURER
RESERVES THE RIGHT TO MAKE
MODIFICATIONS TO PRODUCTS
WITHOUT GIVING PRIOR
NOTICE.
•
MISCELLANEOUS
CHARACTERISTICS ………….………….……...23
HOW TO INSTALL ……….…….…..……....24-29
FINAL CHECKLIST BEFORE STARTING…….29
MINIMUM AND MAXIMUM PLATE SIZES..30
ENVIRONMENTAL NOTE………………………31
CONTACT DETAILS……………………………..32
2
BAUMATIC SUPREMA1W/SS dishwasher user manual
3
IMPORTANT SAFETY INFORMATION
READ BEFORE USING!
CHILD SAFETY
ELECTRICAL SAFETY
•
•
•
•
•
NOTE - This appliance must be grounded. In
the event of a malfunction or breakdown,
grounding will reduce the risk of electric
shock by providing a path of least resistance
of electrical current. You will be able to tell if
it is because a non-grounded appliance will
give off an electrical discharge.
•
DO NOT ABUSE OR FORCE THE
DISHWASHER. DO NOT SIT ON OR STAND
ON ITS DOOR OR DISH RACKS – TIPPING
HAZARD.
•
KEEP CHILDREN AWAY FROM DETERGENT,
RINSE AID AND THE OPEN DOOR OF THE
DISHWASHER AS THERE COULD BE
DETERGENT LEFT INSIDE.
SUPERVISE YOUNG CHILDREN TO ENSURE
THEY DO NOT PLAY WITH THE APPLIANCE.
SUPERVISE INFIRM PERSONS IF THEY MUST
USE THE APPLIANCE.
REMOVE THE DOOR TO WASHING
COMPARTMENT OF YOUR OLD APPLIANCE
BEFORE DISCARDING IT.
•
Manufacturer declines all responsibility for
any damage due to non-grounding of
appliance.
•
•
DURING THE GUARANTEE PERIOD ONLY BAUMATIC
SERVICE ENGINEERS OR AN AUTHORISED AGENT
OF BAUMATIC SHOULD CARRY OUT REPAIRS ON
THIS UNIT.
DO NOT USE IF THE SUPPLY CORD IS DAMAGED.
FOR INSTALLATION PROCEDURE PLEASE CONSULT
PAGES 24 – 29.
DURING USE
•
•
BEFORE USING
SOME ITEMS ARE UNSUITABLE FOR WASHING
IN YOUR DISHWASHER. PLEASE SEE PAGE 8 FOR A LIST
OF THESE ITEMS.
DO NOT TAMPER WITH THE CONTROLS.
WHEN LOADING ITEMS TO BE WASHED:
1) Keep sharp items like knives away from the door
seal.
2) Load sharp knives with the handles up to prevent
injuries.
DO NOT TOUCH THE HEATING ELEMENT
DURING OR IMMEDIATELY AFTER USE.
DO NOT USE YOUR DISHWASHER UNLESS
ALL ENCLOSURE PANELS ARE PROPERLY
IN PLACE. OPEN THE DOOR VERY
CAREFULLY IF THE DISHWASHER IS
OPERATING. THERE IS A RISK OF WATER
SQUIRTING OUT.
AFTER USE
•
ONLY USE AUTOMATIC DISHWASHER
DETERGENT, NOT SOAP OR LAUNDRY DETERGENT.
NEVER USE SOLVENTS AS THIS COULD RESULT IN AN
EXPLOSION!
•
•
ALWAYS KEEP THE DOOR CLOSED TO AVOID DANGER
OF TRIPPING.
CHECK THAT THE DETERGENT DISPENSER IS EMPTY
AFTER COMPLETION OF WASH CYCLE.
IF LEAVING UNUSED FOR A LONG TIME,
DISCONNECT THE WATER SUPPLY (SEE PP. 17, 26).
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY BEFORE
USING YOUR DISHWASHER FOR THE FIRST TIME!
3
4
BAUMATIC SUPREMA1W/SS dishwasher user manual
CONTROL PANEL
1
2
3
4
5
6
7
8
9
10
Display Window: Time remaining in Program; delay time; running indicator; temperature of water; fault codes, etc.
Program Indicator Light.
Power On Indicator Light: Comes on when the power is turned on.
Power Switch: Turns the power supply on /off.
Start / Pause Button: Press this button to start or stop the dishwasher.
Program Button: Press this button to select the program you want to run.
Door Lock: Pull it to open the door.
Delayed Start Button: Press this button to set the delayed hours for washing.
Rinse Aid Warning Light: Add more rinse aid as the indicator on the front panel lights up (Certain Models only).
Salt Warning Light: Add more salt as the indicator on the front panel lights up.
WARNING – BEWARE OF HOT WATER & STEAM AS YOU OPEN THE DOOR!
DISHWASHER FEATURES
1
Adjustable Upper Basket
5
9
Coarse Filter
2
Spray Arms
6
Detergent Dispenser
10
Rinse Aid Dispenser
7
Cup Shelf
11
Drain Pipe Connector
8
Cutlery basket
12
Inlet Pipe Connector
3
4
Lower Basket
Water Softener
Main Filter
4
5
BAUMATIC SUPREMA1W/SS dishwasher user manual
Note on chemicals used by the dishwasher
•
Your dishwasher is equipped with an adjustable rinse aid and salt container. Using individual detergents,
rinse aid and salt will give the best possible results as this will give the correct dosage of each chemical to
suit your needs. Using Two-in-One or Three-in-One tablets may not give the best results when used in
your appliance, and may not be suitable for the type of water supply in your home, as they contain predetermined quantities of salt, rinse aid and detergent and cannot be adjusted to the individual
requirements.
If you are going to use 3-in-1 (or 2-in-1) tablets, we suggest that you contact the manufacturer before use
or if you experience poor results in the wash performance and ask for assistance from them.
WARNING!
ONLY USE DISHWASHER SALT IN YOUR
DISHWASHER.
WATER
SOFTENING
FEATURE
NOTE:
IF YOU USE 3-IN-1 OR 2-IN-1 TABLETS, BE
SURE NOT TO ADD SALT AND/OR RINSE AID
TO THE APPLIANCE AS THESE TABLET
TYPES ALREADY CONTAIN SALT AND/OR
RINSE AID. ADDING SALT AND RINSE AID
TO YOUR DISHWASHER’S COMPARTMENTS
IN A CYCLE INVOLVING A 3-IN-1 OR 2-IN-1
TABLET WILL RESULT IN OVERDOSING OF
INDIVIDUAL CHEMICALS AND MAY CAUSE
OVERFLOWING OF WATER AND SUDS.
THE LIME IN HARD WATER MAKES DEPOSITS FORM ON
DISHES AND UTENSILS. YOUR DISHWASHER HAS A
SPECIAL SOFTENING FEATURE THAT USES SALT
SPECIFICALLY DESIGNED TO ELIMINATE LIME AND
MINERALS FROM THE WATER.
LOADING SALT INTO THE SALT CONTAINER
•
REMOVE THE LOWER BASKET & THEN
UNSCREW AND REMOVE THE CAP
FROM THE SALT CONTAINER.
•
IF YOU ARE FILLING THE CONTAINER
FOR THE FIRST TIME, FILL WITH
APPROX. 1 LITRE OF WATER.
•
PLACE THE END OF THE SUPPLIED
FUNNEL INTO THE HOLE & ADD 1.2 Kg
OF SALT. NOTE: IT IS NORMAL FOR A
SMALL AMOUNT OF WATER TO COME
OUT OF THE CONTAINER.
5
6
BAUMATIC SUPREMA1W/SS dishwasher user manual
SETTING THE WATER SOFTENER LEVEL
YOU CAN ADJUST THE AMOUNT OF SALT USED BY THE DISHWASHER TO SOFTEN WATER TO GET
THE BEST WASHING RESULTS, BASED ON THE HARDNESS OF WATER IN YOUR AREA.
2
THERE IS A RING ON THE NECK OF THE
CONTAINER. ROTATE THE RING IN AN
ANTICLOCKWISE DIRECTION FROM THE “-”
SETTING TOWARDS THE “+” SETTING
ACCORDING TO THE HARDNESS OF WATER
IN USE. SEE TABLE BELOW.
NOTE
1
1. THE SALT CONTAINER MUST BE REFILLED WHEN THE
SALT WARNING LIGHT COMES ON. ALTHOUGH THE
SALT CONTAINER MAY BE FULL, THE INDICATOR LIGHT
MAY NOT GO OUT UNTIL THE SALT HAS DISSOLVED.
2. IF THERE ARE SALT SPILLS, A SOAK PROGRAM CAN
BE RUN TO WASH AWAY SPILLAGE BEFORE USING THE
MACHINE.
3. CLEAR ANY SALT GRANULES AWAY FROM THE
CONTAINER OPENING.
UNSCREW THE CAP FROM THE SALT
CONTAINER.
ADJUSTMENTS SHOULD BE MADE ACCORDING TO THE TABLE BELOW:
WA TE R H ARDN ESS
Se l ect o r Po s iti o n
Salt c on sum pti on
( g ra m/cycl e)
Au to no my
( c ycles/ 1 .2kg s)
0~ 1. 8
/
0
/
Cl a rke D egr e es
dH
mmol /l
0~ 14
0~ 18
14 ~3 6
18 ~4 4
1 . 8~ 4.4
-
20
60
36~ 71
44 ~8 9
4. 4~ 8.9
MED
40
30
71
89
8. 9
+
60
20
Co nt a ct your l oca l wa t er boa rd f or inf or ma ti on on the ha rdne ss o f you r w ate r sup pl y.
DETERGENT “How much do I use?”
To OPEN the DETERGENT DISPENSER DOOR, use the CATCH on its LOWER SIDE.
*NOTE: SEE P.13 – WASH CYCLE TABLE for AMOUNT of DETERGENT to use.
NOTE:
ALWAYS CHECK THE WASH CYCLE TABLE
FOR DOSAGE ADVICE. NEVER OVERFILL
THE DISPENSER.
•
DO NOT OVERDOSE TO PREVENT THE
FORMATION OF DEPOSITS (THE WATER
SOFTENING FEATURE ALREADY TAKES CARE
OF THIS!).
THE HARDER YOUR WATER, THE MORE DETERGENT
YOU MAY NEED. ADJUST THE DOSE JUST BY SMALL
AMOUNTS UNTIL YOU FIND THE CORRECT AMOUNT
OF DETERGENT TO USE.
•
6
BAUMATIC SUPREMA1W/SS dishwasher user manual
RINSE AID
7
•
THE RINSE AID IS RELEASED DURING THE
FINAL RINSE TO PREVENT WATER FROM
FORMING DROPLETS ON YOUR DISHES
THAT CAN CAUSE SPOTS AND STREAKS. IT
ALSO IMPROVES DRYING BY ALLOWING
WATER TO FALL OFF THE DISHES.
•
YOUR DISHWASHER IS DESIGNED TO USE
LIQUID RINSE AIDS. THE RINSE AID
DISPENSER CAN BE FOUND INSIDE THE
DOOR NEXT TO THE DETERGENT
DISPENSER. TO FILL THE DISPENSER, OPEN
THE CAP AND POUR THE RINSE AID INTO
THE DISPENSER UNTIL THE LEVEL
INDICATOR TURNS COMPLETELY BLACK.
THE DISPENSER HOLDS ABOUT 100ML OF
LIQUID RINSE AID.
BE CAREFUL NOT TO OVERFILL THE
DISPENSER – THIS COULD CAUSE
FROTHING. WIPE AWAY SPILLS WITH A
DAMP CLOTH. DON’T FORGET TO REPLACE
THE CAP BEFORE YOU CLOSE THE
DISHWASHER DOOR.
•
•
TO OPEN THE DISPENSER, TURN THE CAP TO
THE ‘OPEN’ (LEFT) ARROW AND LIFT IT OUT.
•
POUR THE RINSE AID INTO THE DISPENSER.
BE CAREFUL NOT TO OVERFILL.
•
REPLACE CAP BY INSERTING IT ALIGNED WITH
‘OPEN’ ARROW & TURN IT TO THE CLOSED
(RIGHT) ARROW.
NOTE: IF YOU HAVE SOFT WATER, YOU MAY NOT
NEED RINSE AID FOR IT MAY CAUSE A WHITE FILM
TO DEVELOP ON YOUR DISHES.
ADJUSTING THE RINSE AID DISPENSER
•
As with detergent, the amount of rinse
aid needed for your dishes depends on
the hardness of the water in your area.
Too much rinse aid can result in
foaming and cause cloudiness or
streaks on your dishes. If your water
is very soft, you may not need rinse
aid. You can always dilute the rinse
aid with an equal amount of water.
The rinse aid dispenser has six settings. ALWAYS START WITH THE DISPENSER SET ON “1”. IF SPOTS & POOR
DRYING ARE A PROBLEM, INCREASE THE AMOUNT OF RINSE AID DISPENSED BY REMOVING THE DISPENSER
LID AND ROTATING THE DIAL TO “2”. IF THE DISHES ARE STILL NOT DRYING PROPERLY OR ARE SPOTTED,
ADJUST THE DIAL TO THE NEXT HIGHER NUMBER UNTIL YOUR DISHES ARE SPOT-FREE.
***NOTE: Please read the notes for detergent use on p. 13.
As the rinse aid diminishes, the size of the black dot on the rinse
aid level indicator changes, as illustrated below.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
WHEN TO REFILL THE RINSE
AID DISPENSER - If the rinse aid
warning light ( SEE control panel) is not on, you
can judge the rinse aid level by looking at the
black dot on the rinse aid dispenser. As the
rinse aid level decreases, the black dot shrinks.
Never let the rinse aid get below ¼ full.
7
BAUMATIC SUPREMA1W/SS dishwasher user manual
LOADING
YOUR
DISHWASHER
8
NOTE:
FOR BEST PERFORMANCE, FOLLOW THESE
LOADING GUIDELINES. FEATURES AND
APPEARANCE OF RACKS & CUTLERY
BASKETS MAY VARY FROM YOUR MODEL.
BEFORE LOADING!
•
• REMOVE ALL SCRAPS OF FOOD.
•
EMPTY DRINKS & LIQUIDS FROM CUPS.
SOFTEN BURNT-ON FOOD IN PANS BY SOAKING.
DO NOT PUT THESE ITEMS IN YOUR DISHWASHER:
•
•
•
BRONZE
CUTLERY
SAUCEPANS
WITH
WOODEN
HANDLES
CUTLERY
WITH
WOODEN,
HORN, CHINA
OR MOTHER
OF PEARL
HANDLES
•
OLDER
CUTLERY
WITH GLUED
PARTS
•
•
•
•
BONDED
CUTLERY
ITEMS OR
DISHES
•
PEWTER OR
COPPER ITEMS
•
•
PLASTIC
ITEMS THAT
ARE NOT HEAT
RESISTANT
•
LEAD CRYSTAL
GLASS
STEEL ITEMS
SUBJECT TO
RUSTING
WOODEN
PLATTERS
ITEMS MADE
FROM
SYNTHETIC
FIBRES (eg.
SPONGES)
DELICATE,
REPAIRED OR
PAINT /
PATTERN
OVERLAID
CHINA
Note:
Do not wash stainless steel and silver cutlery together. Iron objects can rust
and stain other items. Aluminium tends to go black. Copper, pewter & brass
stain.
8
BAUMATIC SUPREMA1W/SS dishwasher user manual
HOW TO USE THE UPPER RACK
THE UPPER RACK IS FOR MORE DELICATE
LIGHTER
DISHWARE
SUCH
AS
AND
GLASSES, COFFEE & TEA CUPS, SAUCERS,
PLATES, BOWLS, AND SHALLOW PANS
(PROVIDED THESE ARE NOT TOO DIRTY).
POSITION THE DISHES AND
COOKWARE SO THAT THEY DO NOT
GET MOVED BY THE SPRAY OF
WATER. ALWAYS PLACE GLASSES,
CUPS & BOWLS UPSIDE DOWN.
NOTE:
YOUR DISHWASHER COMES WITH AN
ADJUSTABLE TOP RACK (BASKET) –
PICTURED AT RIGHT. ITS HEIGHT CAN
BE ADJUSTED BY UNDOING THE FRONT
RAIL CLIPS, REMOVING THE RACK
COMPLETELY AND LATCHING THE
WHEELS OF
THE
LOWER
LEVEL
(POSITION ‘1’ IN THE FIGURE ON THE RIGHT)
1
OR THE HIGHER LEVEL (POSITION ‘2’ IN
THE FIGURE ON THE RIGHT) IN THE GROOVE
OF THE RAIL.
2
9
9
BAUMATIC SUPREMA1W/SS dishwasher user manual
10
***NOTE***: THE UPPER RACK HAS
SIDE FLAPS (PICTURED AT LEFT ABOVE BASKET).
THERE ARE 4 (2 ON EACH SIDE).
THESE CAN BE ADJUSTED INTO 2
POSITIONS = POSITION 1 (HIGH)
AND POSITION 2 (LOW).
TO MOVE THE FLAPS BETWEEN THESE
POSITIONS, FIND THE LARGE HINGES
CLASPING EACH FLAP TO THE UPPER
RACK. THERE ARE TWO OF THESE AT
EITHER END OF EACH FLAP. GENTLY PULL
BOTH CLASPS OFF THE WIRE RACK AND
MOVE THE FLAP TO THE DESIRED
POSITION. BE CAREFUL IF YOU HAVE
LONG FINGERNAILS!
POSITION 1
THE UPPER POSITION WILL ACCOMMODATE ITEMS SUCH AS GLASS TUMBLERS
(PLACED BENEATH FLAP) AND WINE GLASSES. WINE GLASSES CAN BE PLACED
UPSIDE DOWN SO THAT THE NECK NESTLES SNUGLY IN THE GROOVES AT SIDE OF
FLAP WITH THE BASE OF THE GLASS FACING UPWARD.
POSITION 2
WHEN THE FLAPS ARE MOVED TO THE LOWER POSITION, THEY CAN BE USED TO
HOLD ADDITIONAL TUMBLERS, CUPS AND MUGS. ALWAYS CHECK THAT YOU ARE
ONLY PLACING ITEMS ON THE FLAPS THAT WILL CLEAR THE CEILING HEIGHT OF
YOUR DISHWASHER WHEN YOU PUSH THE RACK BACK IN. BE PARTICULARLY
CAREFUL WITH LONG-STEMMED GLASSWARE SUCH AS CHAMPAGNE GLASSES –
BREAKAGE HAZARD!
10
BAUMATIC SUPREMA1W/SS dishwasher user manual
11
NOTE:
• WHEN YOU ARE SATISFIED YOU HAVE LOADED ALL THE UTENSILS
AND DISHES YOU WANT TO WASH AND HAVE ADDED THE PROPER
AMOUNT OF DETERGENT TO THE DISPENSER (REMEMBER TO CHECK THE
TABLE ON PAGE 13 FOR THE DOSE THAT’S RIGHT FOR THE WASHING CYCLE YOU
WANT), ENSURE THE RACKS ARE PUSHED ALL THE WAY BACK INTO
YOUR DISHWASHER AND CLOSE THE DOOR.
• YOU ARE NOW READY TO START A WASH CYCLE (SEE NEXT PAGE).
11
12
BAUMATIC SUPREMA1W/SS dishwasher user manual
STARTING A WASH CYCLE
2
1
10 9
8
6
7
5
4
3
STARTING A WASH CYCLE
1)
2)
3)
4)
5)
MAKE SURE THAT THE PLUG OF THE APPLIANCE IS INSERTED INTO THE WALL SOCKET.
6)
PRESS THE ‘ON/OFF’ BUTTON. THE ON/OFF LIGHT WILL COME ON. THE WASH CYCLE WILL NOW BEGIN.
MAKE SURE THAT THE WATER SUPPLY IS TURNED ON TO FULL PRESSURE.
LOAD THE DISHWASHER (SEE THE SECTION ENTITLED ‘LOADING YOUR DISHWASHER’).
POUR IN DETERGENT (SEE THE SECTION ENTITLED ‘SALT, DETERGENT & RINSE AID’).
TURN THE KNOB LOCATED ON THE RIGHT OF THE CONTROL PANEL CLOCKWISE UNTIL THE NUMBER OR
THE SYMBOL FOR THE CYCLE SETTING IS ALIGNED WITH THE REFERENCE MARK (SEE THE SECTION
ENTITLED ‘WASH CYCLE TABLE’ ON NEXT PAGE).
Note:
The Delay Timer key (in above figure as mark number ‘6’) will set the start of the
washing cycle by 30mins into the future for every press. You can set it up to 9½
hours ahead of time for your convenience.
Approximate Timing of Wash Cycles
Intensive
(strong) 139
mins.
Normal
150
mins.
Economy
95
mins.
12
Rinse
76
mins.
Glass
103
mins.
Soap
7
mins.
BAUMATIC SUPREMA1W/SS dishwasher user manual
13
WASH CYCLE TABLE
OVERFLOW PROTECTION
YOUR BAUMATIC DISHWASHER HAS AN OVERFILL PROTECTION DEVICE WHICH AUTOMATICALLY SHUTS OFF
THE INLET VALVE AND STARTS THE DRAIN PUMP IF THE WATER OVERFLOWS. IF THIS OCCURS THEN TURN OFF
THE MAINS WATER SUPPLY BEFORE CALLING THE SERVICE DEPARTMENT. IF THERE IS WATER IN THE BASE
PAN BECAUSE OF AN OVERFILL OR SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE
DISHWASHER
13
BAUMATIC SUPREMA1W/SS dishwasher user manual
14
WHAT YOU WILL SEE ON THE DISPLAY:
Digital sign: Shows the delayed time, remaining time and fault codes.
Delay sign: Shows this sign when delaying.
Washing sign: Displays this sign when washing.
Running sign: Display shows this when your machine is running a cycle.
Doesn’t flicker when stopping.
Temperature sign: Shows the wash temperature at any time.
FORGET TO ADD A DISH?
A FORGOTTEN DISH CAN BE ADDED AT ANY TIME BEFORE THE DETERGENT
DISPENSER OPENS.
•
OPEN THE DOOR A LITTLE TO STOP THE WASHING.
•
AFTER THE SPRAY ARMS STOP WORKING, YOU CAN OPEN THE DOOR
COMPLETELY.
•
ADD FORGOTTEN DISHES.
•
CLOSE THE DOOR, THE DISHWASHER WILL WORK AFTER TEN
SECONDS.
Need to Change the Cycle?
1.
PRESS THE POWER SWITCH TO STOP WASHING
2.
PRESS THE ‘PROG.’ BUTTON TO SELECT THE NEW PROGRAM
3.
PRESS THE POWER SWITCH AGAIN TO START WASHING
* Note – You may have to start a new cycle by reloading the detergent
if it has been a long time since the old cycle began. See page 12 to see
how to do this.
At the End of the Wash Cycle
At end of washing, the time display will flash for 8 seconds while the ALARM
sounds. The ALARM will not sound at the end of delayed washing, however
We recommend you leave about ½ hour before unloading to
avoid injury and brittleness in dishware from heat.
14
BAUMATIC SUPREMA1W/SS dishwasher user manual
15
FILTERING SYSTEM
FOR YOUR CONVENIENCE, WE HAVE PLACED THE FILTERING SYSTEM WITHIN EASY REACH INSIDE THE
TUB. THE FILTER REMOVES BITS OF FOOD TRAPPED IN THE FILTER FROM THE WASH WATER SO IT CAN BE
RECIRCULATED DURING THE CYCLE. THERE ARE THREE PARTS TO THE FILTERING SYSTEM: 1) The Main Filter,
2) The Coarse Filter & 3) The Fine Filter.
1 MAIN FILTER
Food and soil particles trapped by this filter are
pulverized by a special jet on the lower spray arm and
washed down the drain.
2 COARSE FILTER
Larger items, such as pieces of bone or glass that could
clog the drain are trapped in the coarse filter. To
remove an item caught in this filter, gently squeeze
the tabs on top of this filter and lift it out.
3 FINE FILTER
This filter holds soil and food residue in the sump area
and prevents it from being re-deposited on the dishes
during a cycle.
Caring for your Dishwasher
CLEANING THE OUTSIDE SURFACES OF YOUR APPLIANCE
•
TO CLEAN THE EXTERIOR OF YOUR DISHWASHER (INCLUDING THE CONTROL PANEL), USE A LIGHTLY
DAMPENED CLOTH THEN DRY THOROUGHLY. NEVER USE SHARP OBJECTS, SCOURING PADS OR
HARSH CLEANERS ON ANY PART OF THE APPLIANCE. SOME PAPER TOWELS CAN SCRATCH.
•
TO CLEAN THE EDGE AROUND THE DOOR,
ONLY EVER USE A SOFT WARM, DAMP RAG.
DO NOT USE A SPRAY CLEANER HERE OR
WHEN CLEANING THE DOOR PANEL AS THIS
MAY HARM THE DOOR LOCK AND
ELECTRICAL PARTS.
CLEANING THE SPRAY ARMS
THE SPRAY ARMS NEED REGULAR CLEANING AS HARD WATER RESIDUES WILL CLOG THEIR
JETS & BEARINGS. TO REMOVE THE SPRAY ARM, SCREW OFF THE NUT TO TAKE OUT THE
WASHER ON TOP OF THE SPRAY ARM AND REMOVE THE ARM. WASH THE ARMS IN SOAPY
WARM WATER & USE A SOFT BRUSH TO CLEAN THE JETS. REPLACE THE SPRAY ARM AFTER
RINSING IT THOROUGHLY.
15
BAUMATIC SUPREMA1W/SS dishwasher user manual
16
CLEANING THE FILTERS
•
THE FILTER ASSEMBLY MUST BE KEPT CLEAN FOR BEST PERFORMANCE. You should remove the
larger bits of food trapped in the filter after each wash cycle by rinsing the semicircular filter and
cup under running water. To remove the filter assembly, pull up on the cup handle.
•
The entire filter assembly should be cleaned at least once a month.
•
To clear the coarse filter and the fine filter, use a cleaning brush. Then, reassemble the filter parts
as shown in the figure above and reinsert the entire assembly in the dishwasher in its seat & press
downward to secure it.
•
Improper replacement of the filter may impair appliance performance and damage dishes and
utensils.
• Warning - never run the dishwasher without the filters
in place!
• Warning - Before cleaning the inner cavity of the appliance
always allow 30 minutes for the Element to cool down to
avoid injury!
16
BAUMATIC SUPREMA1W/SS dishwasher user manual
17
HOW TO KEEP YOUR DISHWASHER IN SHAPE
AFTER EVERY WASH, leave the door slightly ajar so that moisture and odours are not trapped
inside.
REMOVE THE PLUG before cleaning or performing maintenance. Never run the risk of electric
shocks.
DO NOT USE SOLVENTS OR ABRASIVE CLEANING AGENTS to clean the exterior and the rubber
parts of the dishwasher. Only use a cloth and warm soapy water. To remove spots or stains
from the surface of the interior, use a cloth dampened with water and a little white vinegar,
or a cleaning product made specifically for dishwashers.
WHEN YOU GO ON HOLIDAY, run a wash cycle with the dishwasher empty. Then unplug it, turn off
the water supply and leave the door slightly ajar to prevent odours and mould from developing.
MOVING THE APPLIANCE is possible but KEEP IT UPRIGHT.
SEALS can trap food, which in turn will cause odours. Periodic cleaning with a damp cloth or
sponge will prevent this from becoming a problem.
PROTECTING YOUR DISHWASHER AGAINST FREEZING
If your dishwasher is left in an unheated place during the winter, ask a
service technician to:
1)
Cut off electrical power to the dishwasher. Remove fuses or trip circuit
breaker.
2)
Turn off the water supply and disconnect the water inlet pipe from the water
valve & discharge hoses.
3)
Drain water from the inlet pipe and water valve (Use a pan to catch the
water).
4)
Reconnect the water inlet pipe to the water valve.
5)
Remove the plastic sump cover in the tub bottom and use a sponge to soak
up water in the rubber boot.
17
BAUMATIC SUPREMA1W/SS dishwasher user manual
18
BEFORE YOU CALL FOR SERVICE …
CHECKING AGAINST THE CHARTS BELOW MAY FIX YOUR PROBLEM.
PROBLEM
POSSIBLE CAUSES
•
Dishwasher
doesn’t run!
Drain Pump
doesn’t stop!
Fuse blown, or the
circuit breaker acted
•
Power supply is not
turned on
•
Water pressure is low
•
Overflow
•
Some audible sounds
are normal
•
Utensils are not secure
in the baskets or
something small has
dropped into the
basket and is loose
Noise!
•
Motor Hums
18
WHAT TO DO
•
Replace fuse or reset circuit
breaker.
•
Remove any other appliances
feeding from the same socket as
the dishwasher.
•
Make sure the dishwasher is turned
on and the door is closed securely.
•
Check that the water supply is
connected properly and the water is
turned on.
•
The system is designed to detect an
overflow. When it does, it shuts off
the circulation pump and turns on
the drain pump. Call a Baumatic
Ltd approved technician.
•
Sound from soft food shredding
action and detergent cup opening.
This is not a problem.
•
Ensure everything is placed
securely in the dishwasher.
•
Dishwasher has not been used
regularly. If you do not use it
often, remember to set it to fill and
pump out every week. (See Wash
Cycle table). This will help keep the
seal moist.
BAUMATIC SUPREMA1W/SS dishwasher user manual
PROBLEM
POSSIBLE CAUSES
19
WHAT TO DO
•
Improper detergent
•
Use only special dishwasher
detergent to avoid suds.
•
Spilled rinse agent
•
Always wipe up rinse agent spills
immediately.
•
Detergent with
colorant was used
•
Make sure you use detergent
without colorant.
Dishes are not
dried!
•
Rinse agent dispenser
is empty
•
Make sure that the rinse agent
dispenser is filled.
Dishes and
Flatware not
Clean!
•
Improper program
•
Select stronger program.
•
•
Improper rack loading
Make sure there are no large dishes
blocking the action of the detergent
dispenser and the spray arms.
Suds in the Tub!
Stained tub
Interior!
To remove spots from glassware:
Spots and Filming
on Glasses and
Flatware!
•
•
•
•
•
•
•
Extremely hard water
Low inlet temperature
Overloading the
dishwasher
Improper loading
Old or damp powder
detergent
Empty rinse agent
dispenser
Incorrect dosage of
detergent
19
1. Take all metal utensils out of the
dishwasher.
2. Do not add detergent.
3. Choose the longest cycle.
4. Start the dishwasher and let it to run for
18 - 22 minutes, then it will be in the main
wash.
5. Open the door and pour 2 cups of white
vinegar into the bottom of the dishwasher.
6. Close the door and let the dishwasher
complete the cycle.
7. If the vinegar does not work, repeat as
above, only use ¼ cup (60ml) of citric acid
crystals instead of vinegar.
BAUMATIC SUPREMA1W/SS dishwasher user manual
PROBLEM
Cloudiness on
glass!
Yellow or brown
film on inside
surfaces!
White film on
inside surface!
POSSIBLE CAUSES
•
Combination of soft
water and too much
detergent
•
Tea or coffee stains
•
Iron deposits in water
can cause an overall
film
20
WHAT TO DO
•
Use less detergent if you have soft
water and select a shorter cycle to
clean the glassware.
•
Use a solution of ½ cup of bleach
and 3 cups warm water to remove
the stains by hand. Rinse
thoroughly.
•
You have to call a water softener
company for a special filter.
•
To clean the interior, use a damp
sponge with dishwasher detergent
and wear rubber gloves. Never use
any other cleaner than dishwasher
detergent for the risk of foaming or
suds.
•
Hard water minerals
•
Button is not in the
‘OFF’ position
•
Turn the Button to ‘OFF’ position
and slide the door latch to the left.
Detergent left in
dispenser cups!
•
Dishes block detergent
cups
•
Reload the dishes properly.
Steam!
•
•
Normal phenomenon
There is some steam coming
through the vent by the door latch
during drying and water draining.
Detergent cup lid
won’t latch!
20
BAUMATIC SUPREMA1W/SS dishwasher user manual
PROBLEM
Black or grey
marks on dishes!
Water standing in
the bottom of the
tub!
POSSIBLE CAUSES
•
•
•
Aluminium utensils
have rubbed against
dishes
Dishwasher leaks!
Door popping
open!
WHAT TO DO
•
Use a mild abrasive cleaner to
eliminate those marks by hand.
•
A small amount of clean water
around the outlet on the tub bottom
at the back of the tub keeps the
water seal lubricated. No action
needed.
•
Be careful not to overfill the rinse
aid dispenser.
•
Spilled rinse aid could cause
oversudsing and lead to
overflowing.
•
Wipe away any spills with a damp
cloth.
•
Make sure the dishwasher is level.
•
Make sure if you’re using 3-in-1
tablets that you do not put rinse aid
and salt into the appliance as well.
•
Level appliance & ensure top screws
attaching appliance to work surface
are not lifting the weight of the
dishwasher.
This is normal
Overfilled dispenser or
rinse aid has spilled
•
Dishwasher isn’t level
•
3-in-1 Tablets
•
Appliance not level
WARNING!
IF OVERFLOW OCCURS, TURN OFF THE MAIN WATER SUPPLY BEFORE CALLING A SERVICE
TECHNICIAN. IF THERE IS WATER IN THE BASE OF THE TANK PAN BECAUSE OF AN OVERFILL
OR SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE DISHWASHER.
21
21
22
BAUMATIC SUPREMA1W/SS dishwasher user manual
ERROR CODES - WHAT THEY MEAN
* YOUR DISHWASHER MAY EXPERIENCE A FAULT. SHOULD THIS HAPPEN, A
CODE CONSISTING OF ‘E’ & A NUMBER FROM 1-7 CAN BE DISPLAYED.
USE THIS TABLE TO UNDERSTAND WHAT IS WRONG.
*NOTE*: ALWAYS CALL FOR A Baumatic Ltd ENDORSED / APPROVED
SERVICE TECHNICIAN TO CARRY OUT REPAIRS.
CODE
SYMPTOM:
CAUSE:
WHAT TO DO:
‘Err1’
LONGER FILL TIME.
FAUCET IS NOT OPENED.
Ensure that inlet hose is not
kinked or crushed.
‘Err2’
LONGER or EXTENDED DRAINING TIME
THE DRAIN PIPE WAS PLACED
TOO HIGH WHEN IT WAS
INSTALLED.
Ensure drainage system is as
per manual and not
extended.
‘Err3’
LONGER HEATING TIME – NOT
REACHING REQUIRED TEMPERATURE
MALFUNCTION OF
TEMPERATURE SENSOR OR OF
HEATING ELEMENT.
CALL FOR A QUALIFIED
SERVICE TECHNICIAN.
TOO MUCH INLET WATER.
‘Err4’
OVERFILLED
*NOTE * - THERE ARE
NUMEROUS CAUSES OF AN
‘Err4’ MESSAGE. REFER TO
APPLIANCE USAGE SECTION
OF THIS MANUAL FOR
GUIDELINES ON HOW TO
PREVENT AN OVERFILL.
Overdosing. 3-in-1 put in
with salt and/or rinse aid in
the appliance =overdose.
Could also be a Water
Pressure problem.
‘Err6’
OPEN CIRCUIT
THERMISTOR.
CALL FOR A QUALIFIED
SERVICE TECHNICIAN.
‘Err7’
SHORT CIRCUIT
THERMISTOR.
CALL FOR A QUALIFIED
SERVICE TECHNICIAN.
WARNING!
IF OVERFLOW OCCURS, TURN OFF THE MAIN WATER SUPPLY BEFORE CALLING A SERVICE
TECHNICIAN. IF THERE IS WATER IN THE BASE OF THE TANK PAN BECAUSE OF AN OVERFILL
OR SMALL LEAK, THE WATER SHOULD BE REMOVED BEFORE RESTARTING THE DISHWASHER.
22
BAUMATIC SUPREMA1W/SS dishwasher user manual
23
DISHWASHER CHARACTERISTICS
The BAUMATIC SUPREMA1W/SS dishwasher model is based firmly on convenience.
Apart from having the same general workings as other household dishwashers, it has
several extra features.
14 place settings -
Performance of
Dishwasher - Your dishwasher has a A rated wash
Normal wash load of 14 place settings.
performance, A rated drying performance and A rated energy
efficiency.
Rinse aid Warning
Indicator - If the rinse aid is running low,
Overflow protection -
Your
dishwasher has an overfill protection program which could
automatically shut off the inlet valve and start the drain pump if the
water Overflows.
this signal will light up on the control panel, alerting
you to top the rinse aid level up so the machine can
keep at its optimum performance level.
Automatic Power off
function
Stainless steel tubYou need not worry about stains to the tub.
6 wash programs -
Automatically shuts the power off after washing.
You can choose
desired program according to the soiled level. Such as, intensive
wash, normal wash, economy, rinse, glass, rapid and pre-wash,
etc. Then you can change the temperature of the wash.
Adjustable upper basket
-
Even if the dishware is large, you can load the dishes by
adjusting the basket.
Error alarm–
Fault codes
show on the display if there is a fault with your
dishwasher.
Salt Warning Indicator If the salt is running low, this signal will light up on the control
panel to alert you to top the salt level up so the machine can
keep at its optimum performance level.
Temperature display Displays the wash temperature at any moment. If you know the
water temperature, you’ll be less likely to be scalded when you
open the door.
Broad applied
voltage - This appliance uses AC
Remaining time
indicator
(alternating current) voltage. Please be aware that this
will make its operation vulnerable to uneven current in
your home and power surges.
The length of time left in the program will be clearly
displayed in the text window, leaving you in no doubt
as to when the program will end.
4 Different wash
temperatures
Time delay feature –
This
allows the start of the program to be delayed between 1 and 9½
hours for your convenience and for saving on energy!
The intensive, normal, economic, rinse, glass
and rapid wash have different temperature
options which you can set before you start a
washing cycle.
23
BAUMATIC SUPREMA1W/SS dishwasher user manual
24
INSTALLATION INSTRUCTIONS
NOTE: APPLIANCE SHOULD ONLY BE FITTED
BY A TRAINED TECHNICIAN
INSTALLING YOUR DISHWASHER
Your dishwasher is with a freestanding feature, you
only need to do following:
80;/
1 Levelling the Appliance(pls see the section “get your dishwasher
level in page 25)
2 Connect the water inlet (pls see page 26)
3 Electrical connection (see page 27)
Also you can install it to a cabinet cavity according
following:
a)
PREPARATION
Before you install your appliance, make sure that the place you
have chosen to fit it is:
o Near the existing
power socket
(marked 4 in figure).
o So that you can
choose one side of the
cabinet cavity to
easily connect the
dishwasher’s drain
hoses.
o Near your sink so
you have easy
access to the water
inlet and drain hoses
(marked 3
[inlet] & 2 [drain] in
figure).
24
BAUMATIC SUPREMA1W/SS dishwasher user manual
INSTALLING
YOUR
DISHWASHER
INTO A CABINET
AREA
o
o
25
REMEMBER THE DIMENSIONS
OF YOUR DISHWASHER!
THESE ARE (measured in
figure in mm):
If dishwasher is to be
installed at the corner
of cabinet area, make
sure you have enough
space when the door is
opened.
Is structured so that
you have less than
5 mm between the
top of the dishwasher
and
cabinet.
Also
check
that the
outer door is aligned
to cabinet.
FIRSTLY, GET YOUR DISHWASHER LEVEL
-
Use spirit levels to
level your
dishwasher
Note:
Once the appliance is positioned, adjust the
Four feet (screwing them in or out)
to adjust the height of the dishwasher, making
it level. In any case, the appliance should
not be inclined more than 2°.
25
b) Connecting to the mains water supply
IMPORTANT: Do not connect the appliance to your mains water supply
using an old or an existing water inlet hose. The inlet hose supplied with
the dishwasher is the ONLY one that should be used.
DO NOT CONNECT THE WATER INLET HOSE TO A HOT WATER TAP.
o
o
o
The inlet hose will be located inside the cabinet of the dishwasher.
Connect the water inlet hose to a threaded water tap that has a 3/4” thread.
Fully tighten the inlet hose to the water tap.
IMPORTANT: If the inlet hose is fitted with an aqua stop. This
MUST be fitted in the upright position, as shown in the above
diagram.
c) Connecting the drain hose
9 Secure the drain hose, so that it cannot move whilst the dishwasher is in use.
9 Place the end of the drain hose on your drain pipe. Push it a short way down
into your drain pipe.
9 IMPORTANT: Do not insert the drain hose too deeply into the water pipe, as
this may cause siphoning.
9 NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL LENGTH.
26
BAUMATIC SUPREMA1W/SS dishwasher user manual
27
d) NOW YOU ARE READY TO CONNECT THE
POWER CORD.
WARNING!
ELECTRICITY CAN BE DANGEROUS. PLEASE READ THE FOLLOWING
CAREFULLY:
ELECTRICAL CONNECTION
Electrical Requirements
The dishwasher is designed for operation on an adequately wired individual 220-240V AC,
50Hz system. The required fuse rating is 13amp. Fused electrical supply is required –
copper wire only. Time delay fuse or circuit breaker is recommended. Make sure that this
appliance runs off its own separate circuit. Outlet should be placed in adjacent cabinet.
WARNING – ENSURE PROPER GROUND EXISTS
BEFORE USE.
After making sure that the voltage and the frequency values for the current in your home
correspond to those on the rating plate and that the electrical system is sized for the
maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not right for
the plug, replace the socket, rather than using adaptors of the like as they could cause
overheating and fire.
27
BAUMATIC SUPREMA1W/SS dishwasher user manual
28
e) THEN, APPLY THE CONDENSATION STRIP.
The Condensation Strip must be fitted to the
underside of the worktop above your dishwasher
to protect it against any moisture. Its purpose
is to deflect steam rising from your appliance to
protect your worktop’s underside.
•
•
The strip is located inside your
dishwasher.
Ensure the surface is clean prior to
sticking to underside of the worktop.
•
Separate the backing paper from the
strip.
•
Stick to the underside of the worktop.
Note: Failure to attach strip could
result in damage to the underside
of your work surface!
f) NOW YOU ARE READY TO PUSH THE
DISHWASHER INTO POSITION (SEE FIGURE BELOW):
NOTE –
MAKE SURE YOU HAVE THE
DISHWASHER ON ITS SLIDE
RAILS
(SEE ILLUSTRATION ON
RIGHT).
* Note *
You can detach the top board
(5) that comes as part of your
dishwasher if you want to
install your dishwasher in your
cabinet.
THEN MOVE IT INTO THE
CABINET RECESS (AS
PICTURED ON RIGHT, 6-7),
ENSURING THAT IT IS BACKED
UP AGAINST THE WALL.
g) ENSURE THAT YOUR DISHWASHER IS LEVEL
IN ITS NEW POSITION.
28
BAUMATIC SUPREMA1W/SS dishwasher user manual
29
NOTE:
YOUR DISHWASHER MUST BE
LEVEL FOR PROPER DISH RACK
OPERATION AND WASH
PERFORMANCE. (GO BACK AND LOOK
AT THE BOTTOM RIGHT DIAGRAM ON PAGE
24).
IT’S IMPORTANT TO MAKE SURE
THAT YOUR DISHWASHER IS
LEVEL AGAIN, BECAUSE THE
FLOOR SURFACE MAY BE
DIFFERENT TO WHERE YOU HAD
ADJUSTED IT BEFORE YOU MOVED
THE DISHWASHER INTO PLACE
WARNING!
BE CAREFUL WHILE YOU ARE LEVELLING YOUR DISHWASHER IN PLACE
– IT COULD TIP OVER AND INJURE YOU!
FINAL CHECKLIST BEFORE OPERATING
NOTE: BEFORE YOU START USING YOUR DISHWASHER,
PLEASE MAKE SURE YOU HAVE CHECKED:
•
•
•
•
•
•
•
WHETHER THE DISHWASHER IS LEVEL AND
FIXED.
WHETHER THE INLET VALVE IS OPENED.
WHETHER THERE IS LEAKAGE AT THE
CONNECTIONS OF THE CONDUCTS.
WHETHER THE WIRES ARE TIGHTLY
CONNECTED.
WHETHER THE POWER IS SWITCHED ON.
WHETHER THE INLET AND DRAIN HOSES
ARE KNOTTED / KINKED.
WHETHER ALL PACKING MATERIALS &
PRINTED MATTER HAVE BEEN REMOVED
FROM THE DISHWASHER.
PLEASE KEEP THIS MANUAL FOR FUTURE
REFERENCE
29
Minimum and maximum plate sizes
With upper
basket raised
With upper
basket lowered
Maximum height of
dishes (upper basket)
19 cm
24 cm
Maximum height of
dishes (lower basket)
30 cm
25 cm
IMPORTANT: Care should be taken to make sure that the spray
arms can move freely when items have been loaded into the
baskets.
Environmental note
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Service Telephone
(0118) 933 6911
Service Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Technical Advice Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Republic of Ireland
01- 6266 798
Czech Republic
Baumatic CR spol s.r.o.
Amperova 495
46215, Librec
Czech Republic
+420 800 185 263
www.baumatic.cz
Slovak Republic
Baumatic Slovakia, s.r.o.
Skultetyho 1
831 04 Bratislava 3
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Janderstrasse 9
Mannheim, 68199
Germany
+4962 112 9190
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Caltana 129
Campodarsego (Padova), 35011
Italy
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Grindzuigerstraat 22
1333 MS ALMERE
The Netherlands
+3136 549 1555
www.baumatic.nl
2