Casablanca Holliston C31UxxZ Owner`s manual

Holliston
F O R
7 61 C o r p o r a t e C e n t e r D r i v e
P o m o n a , C a l i f o r n i a 9176 8
1 . 8 8 8 . 2 2 7. 21 7 8
w w w. c a s a b l a n c a fa n c o . c o m
PN C3143001-AT0209
®
M O D E L :
C31UxxZ
O W N E R ’S
M A N U A L
LIMITED WARRANTY
Holliston®
THIS WARRANTY
SUPERSEDES ALL
PREVIOUS WARRANTIES
If purchased from our authorized dealer, this ceiling fan is warranted to the original purchaser by Casablanca Fan
Company against defects in materials and workmanship for the following:
Motor excluding Electronics�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������Lifetime
Component Parts, Electronic or Manual Control, Blades, Light Fixture, and Finish��������������������������������������������������������������������� One Year
Lightbulbs�������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������� No Warranty
During the warranty period, we repair (or, at our option, replace at no charge) a defective product. For details, contact
Casablanca at 1-888-227-2178 or visit us on the Web at www.casablancafanco.com.
HOW TO OBTAIN SERVICE: Contact Casablanca for the name of the nearest Authorized Service Center or refer to
the Authorized Service Centers list included with this Owner’s Manual. Do not return your fan without approval from
Casablanca Fan Company. Should it become necessary to return your fan to an Authorized Service Center, make sure it
is packaged properly to avoid in-transit damage, which is not covered by this warranty.
WHAT IS NOT COVERED:
Casablanca Fan Company requires the use of genuine Casablanca accessories with this fan.
Where a failure of this fan is caused by the use of accessories not supplied by Casablanca, this warranty is void.
This warranty does not apply if the product has been damaged by improper installation, neglect, accident, misuse,
exposure to extremes of heat or humidity, or as a result of service or modification by other than a Casablanca Authorized
Service Center. In addition, this warranty does not cover minor variations in plated metal finishes due to the imperfect
nature of the plating and finishing process. Handblown glass may contain blisters, seeds, or thin lines. These
characteristics are not defects, but substantiate that this is handblown and handcrafted glass. All costs of installing,
removing, and reinstalling the product are the responsibility of the owner. Under-warranty motors requiring
repair must be shipped to the factory for replacement. Casablanca will pay for shipping charges incurred in sending
the defective product from the customer to Casablanca Fan Company as well as for return UPS shipment. No other
expressed warranty is given. The repair or replacement of a product is the consumer’s exclusive remedy. Any implied
warranty of merchantability or fitness is limited for consequential or incidental damages.
IN-HOME SERVICE: Casablanca offers In-Home Service where available as follows:
Within the first 120 days, Casablanca will send a field service representative to repair or replace the part or parts
deemed to be defective from the factory. Most Service Center contracts cover up to a 30-mile radius from their place of
business. Casablanca will not cover repairs caused by improper installation. After the 120-day period, the consumer
will be charged for the service call and labor. Casablanca will pay for all defective parts through the duration of the
parts warranty. NOTE: Service Centers are required to submit a Proof of Purchase with each warranty claim. The
consumer must provide a copy of the Proof of Purchase at the time of service. If no in-home service is available,
the consumer has the option of sending an in-warranty fan to Casablanca Fan Company in
Pomona, Calif., for repair. The fan must be packaged properly, shipped freight prepaid,
and include a copy of the Proof of Purchase. The fan will be repaired and returned at
no charge to the consumer, freight prepaid.
July 2008
Proof of Purchase
Retain this information for future reference.
Serial number
Model number
Retailer
Date of purchase
Date of Product Registration (mailed card or completed online)
If you have any problem installing or
operating your fan, do not return this
product to the dealer. Call our toll-free
Consumer Affairs hotline at 888-227-2178,
Monday through Friday,
7 a.m. to 4 p.m. PST.
Your request will be handled immediately.
Holliston™
Holliston™ Owner’s Manual
Read and Save These Instructions!
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and
proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s
manual completely and carefully. Retain this manual for future reference.
Caution: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker
or fuse box before attempting any installation procedure.
CONTENTS
PACKAGING
Please Inspect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Parts Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Introduction
Before You Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safe Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MOUNTING RECOMMENDATIONS
General Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Sloped Ceiling Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Fan Installation
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ceiling plate Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Lag Screw Installation (Required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Canopy Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fan Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Lightbulb Installation (uplight) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Hanging the Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Canopy Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Canopy Hatch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Blade Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Light Fixture Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
INTELI•TOUCH® w-84 WALL Control
Wall Control Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Changing Transmitter Frequency Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Bezel Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Care Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
PN C3143001 AT0608
1
PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING!
Your Casablanca fan was crafted with pride and care and inspected thoroughly prior to shipment. Before
you begin to assemble and install your Casablanca fan, remove all parts from the carton and check them
against the Parts Guide in this manual.
Make sure all parts are included in the box using the Parts
Guide on the following pages.
If there are missing or broken parts:
Call 1-888-227-2178 Monday through Friday, 7 a.m. to 4 p.m.
PST. Your request will be handled immediately. Replacement
parts will be sent to you via Federal Express.
Proper Parts Handling
Do not remove lightbulbs from their packaging until you are
ready to install them.
Before discarding packaging materials, be certain that all parts
have been removed.
Use a clean, dry paintbrush to remove small Styrofoam pieces
that may remain after unpacking.
Do not brush Styrofoam into wiring cavities.
The blades in each pack are matched for equal weight to assure
smooth fan operation. If more than one fan is being installed,
do not mix blades from different cartons.
Always turn power to the ceiling fan OFF before replacing
lightbulbs or working on your fan.
Never insert anything into the path of the fan blades while
the fan is in operation.
Never install a fan over a pool or spa.
Never operate a fan that has been damaged in any way.
Install the fan according to the instructions in this manual.
If the fan does not work:
Refer to the Troubleshooting Tips in this Owner’s Manual.
Call Technical Support at 1-888-227-2178.
Contact your local Authorized Service Center.
Our Web site at www.casablancafanco.com contains additional
information on Casablanca products, troubleshooting, and
Authorized Dealer or Service Centers. Please do not return
this product to the store.
When cleaning, painting, or working near your fan, be cautious
of the fan and blades.
RECORD MODEL AND SERIAL NUMBERS BEFORE INSTALLATION!
Please take a moment to locate the model number and serial number from your fan (see below) and record this information on
the Warranty page inside the front cover of your Owner’s Manual if it does not appear there already. These numbers are found on
the motor identification plate affixed to the fan motor in the location shown below:
Motor Identification Plate
Holliston®
TYPEHANGER TYPE
POMONA, CA
SERIAL No.: DJ06 2237
C31UxxZ
2
DJ01 1151 MODEL #C31UxxZ
Serial Number
Model Number
Holliston™
Parts Guide
Item #
Description
Picture (not to scale)
Quantity
1.
Motor Housing
1
2.
Ceiling plate
1
3.
Phillips Screwdriver
1
4.
Screw Pack (A):
11/2" x 8-32" Roundhead screws and Washers ,
2 EA
5.
Screw Pack:
Lag Screw and Washer (1)
1 EA
6.
Screw Pack (A):
Wire Nuts (4),
4
7.
Canopy and Canopy Hatch
1
8.
Perma•Lock™ Downrod
and Ball Assembly
1
9.
Hanging Adapter Cover
1
Canopy Cover Ring
1
10.
11.
12.
13.
Screw Pack (B):
Canopy Screws and Lock Washers,
Allen Wrench
7-Watt Incandescent
Uplight Bulbs
4 EA
1
6
3
Item #
Description
Picture (not to scale)
Quantity
15.
Blades
5
16.
Blade Irons
5
17.
Screw Pack (C):
11
18.
Screw Pack (D):
Blade Screws and Washers
Blade Iron Screws (pre-installed, see pg 13, step 9a)
16 EA
19.
Light Kit
Adaptor Assembly
1
20.
Screw Plug
1
21.
Switch Housing Cap
1
22
Screw Pack (E):
2
23
W-84 Control and Mounting Hardware
1
4
Switch Housing Cap Screws 8-32 x 3/8
Holliston™
Introduction
Before You Start
• CAUTION: RISK OF ELECTRICAL SHOCK! Installation is to be in accordance with the National Electrical Code,
ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use a qualified
electrician. To avoid overheating and possible damage to other equipment, do not install control to a receptacle,
fluorescent light fixture, motor-operated appliance, or transformer-supplied appliance.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for
ceiling fan installations. If it is not, a new box must be installed. Casablanca extension poles are available for
sloped or high ceiling installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The
maximum current requirement for the fan with light fixture is 3.0 amps. The fan uses about 1.1 amps or 120
watts. Maximum light current is about 1.9 amps or 232 watts of lighting.
•Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy
hatch, make sure all wires are within the canopy and that no wires are being pinched.
•WARNING: Do not bend the blade brackets when installing the brackets, balancing the blades, or cleaning the
fan. Do not insert foreign objects in between the rotating fan blades.
Unpacking
Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them
against the parts listed in the Parts Guide. Before discarding packaging materials, be certain that all parts have
been removed.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
Safe Use
•The blades in each pack are matched for equal weight
to assure smooth fan operation. If more than one fan
is being installed, be careful not to mix blades from
different cartons.
Fuse Box
(Remove fuse for the
circuit you will be
working on)
Circuit Breaker
(Trip breaker for the
circuit you will be
working on)
• Inspect the contents of your carton for possible
shipping or handling damage. If parts are missing or
damaged, call 1-888-227-2178.
• It is always a good idea to have an assistant to help
with the installation.
•When cleaning, painting, or working near your fan,
be very careful of the fan and blades. Always turn the
power OFF to the ceiling fan before working on it or
replacing lightbulbs.
• Never insert anything into the path of the fan blades
while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in any
way. Contact Casablanca Fan Company by calling
1-888-227-2178, or contact your local authorized
Casablanca dealer for assistance in obtaining
service.
18" ­
70"­
84"
Dimensions indicated are the minimum
allowable for proper installation.
5
MOUNTING RECOMMENDATIONS
General Guidelines
Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and
fan size are all important factors to consider before installation.
Location
Ceiling fans have practical uses in almost every room in your home. We suggest
you follow these mounting recommendations as you decide where to install
your Casablanca fan.
• For safety reasons, the fan blades must be a minimum of 7' above the
floor.
• Do not locate the fan in a doorway or above a swinging door.
• In bedrooms, fans work best when mounted above the foot of the bed.
• Over pool tables, be sure to provide plenty of clearance to avoid damage
from pool cues.
• In kitchens, be sure to allow for open cupboard doors to clear the fan
blades.
• Do not install a fan close to or over a pool or spa. High humidity combined with corrosive gases will destroy the finish and
warp the blades.
Fan Size
Variable fan speed capability permits the use of a full-size 52" fan even in smaller rooms. For very large rooms, two fans may
be needed.
sloped ceiling installations
Suggested Extension Pole Lengths
Ceiling Height
8' 0"
8' 6"
9' 0"
9' 6"
10' 0"
11' 0"
12' 0"
13' 0"
14' 0"
Pole Length
Extension
Pole
3.5"
3.5"
12"
12"
18"
24"
36"
48"
60"
Maximum
Hang-Tru®
angle 32º
Blades must be a
minimum of 7 feet
above the floor
7' minimum
When to Use Extension Poles
For optimum performance and appearance, an
extension pole should be used with your Casablanca
fan when installing on high (cathedral) ceilings or
sloped ceilings. Casablanca offers standard poles in
increments of 6" up to 5'. Custom poles are available
in lengths up to 9'9". See your Authorized Casablanca
Dealer for details.
Note: Fan may wobble or vibrate if pole length is
not long enough and inside blade is too close to
downslope or side wall. Extending pole length will
usually solve the problem.
EXAMPLE 1
EXAMPLE 2
Calculation of Ceiling Angle
Use the tear-off Ceiling Angle Template card inserted
in this manual. It provides you with a simple “go” or
“no-go” for installing your fan on a sloped ceiling.
6
EXAMPLE 3
This slope is less than 32º.
It is OK to install your fan.
This slope is 32º. This is the maximum slope that will allow the fan to
hang straight down. It is OK to install
your fan.
This slope is more than 32º. Your
fan will not hang straight down; an
adapter is necessary. Contact your
local Authorized Casablanca Dealer
in regards to purchasing a “Sloped
Ceiling Adapter.”
Holliston™
Fan Installation
Getting Started
Installing a New Ceiling Fixture Outlet Box
Using Existing Ceiling Fixture Outlet Box
If you do not have an existing fixture located where
you wish to place your Casablanca fan, an approved
ceiling fixture outlet box must be installed and wired.
After turning the power OFF at its source (either the
circuit breaker or fuse box), lower the old fixture and
disconnect the wiring. Check the ceiling fixture outlet
box to be sure it is marked “Approved for Ceiling Fan
Mounting.” If it is not, a new box must be installed.
warning!
To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box
marked “Acceptable Fan Support of 22.7
kg (50 lbs.) or less” using the mounting
hardware provided with the outlet box.
Note: The weight of this fan is 26 pounds.
Ceiling plate Installation
Ceiling Hardware (not to scale)
Ceiling Plate
Screw Pack:
Lag Screw and Washer (1)
1" x 8-32 Roundhead Screw and Washer (2)
Note: After removing the old fixture, check the outlet
box to ensure that it is supported by a joist or beam
across its upper surface. If not, a 2 x 4 stud must be
installed.
Step 1a. Remove the knockout plug in the center of
the outlet box or drill a 1/2-inch hole for the lag screw
to pass through. Then drill a 1/4-inch guide hole into
the joist or beam to a depth of 3 inches.
Step 1b. Route the outlet box wires through the hole
of the ceiling plate as shown. Attach the ceiling plate
to the outlet box with the screws provided, making sure
the outlet box wires are not being pinched.
Wire Nut (4)
JOIST
CEILING FANAPPROVED
WIRING BOX
CEILING
PLATE
CEILING
WIRING
CAUTION:
To reduce the risk of personal injury, use
only the mounting hardware provided
with the approved outlet box to install the
ceiling plate.
Outlet Box
Hardware
WASHERS
7
Lag Screw Installation
NOTE: This step is required only under two conditions:
If the fan weighs 36 lbs. or more or if the existing ceiling
fixture outlet box needs to be modified for a ceiling
fan application (for example, if the house is not new
construction and you are replacing an existing light
fixture). We recommend that the ceiling box be of
sufficient capacity to support the weight of the fan and
light fixture under any conditions. If in doubt whether
you need to install the lag screw, consult a qualified
electrician.
Step 2. With the large washer attached, pass the lag
screw through the center hole of the ceiling plate and
screw into the guide hole. Tighten until the outlet box is
mounted firmly to the beam. This box must be secured
to the ceiling firmly.
Canopy Installation
Canopy Hardware (not to scale)
Canopy Hatch
Canopy
Canopy Screws and (4) Lock Washers
Phillips
Screwdriver
Step 3. Attach the canopy to the ceiling plate with
three of the 8-32 x 21/2" long canopy screws and lock
washers provided with your Casablanca fan. Tighten
using the provided screwdriver until snug against
the ceiling.
NOTE: On sloped ceilings, align the canopy opening
with the top or peak of the room.
CANOPY
LOCK WASHERS
CANOPY SCREWS
8
Holliston™
Fan Preparation
Perma•Lock™ Hardware (not to scale)
Perma•Lock™ Downrod
and Ball Assembly
Hanging Adapter Cover
IMPORTANT SAFETY INFORMATION:
Before starting the installation of your
ceiling fan, install the threaded downrod into
the motor coupling and lock the assembly.
Canopy Cover
Ring
Allen Wrench
(6) 7-Watt
Uplight Bulbs
PAPER MOTOR
SHIELD
Figure #1
Prepare for fan installation as follows:
Step 4a. Remove the paper shield from the motor as
shown in Figure #1.
Step 4b. Using the provided Allen wrench (attached
to the paper motor shield), loosen the Allen set screw
making sure that end of the Set Screw can not be
seen within the motor coupling as shown in (Figure
#2). If so, you will need to unscrew the Set Screw so
that the tip of the Set Screw does not remain in the
path of the downrod as shown in (Figure #3).
CAUTION: Failure to fully lock in the
downrod before securely tightening the
Allen set screw may cause the fan to
separate from the downrod and fall during
normal operation.
Figure #2
Figure #3
9
Fan Preparation - continued
Step 4c. Slide both the hanging adapter cover and
canopy cover ring on to the pole, then route the
wires through the 3.5" Perma•Lock downrod and ball
assembly as shown in Figures #4. Insert the downrod
into the motor coupling and turn it clockwise until it
stops turning, ensuring that the pole has bottomed
out.
Tip: The downrod has a tapered thread that is designed
to lock completely when installed correctly.
Step 4d. Tighten the set screw with the Allen wrench
as shown in Figure #5 to ensure safe operation of your
fan. If it is tight enough, you should not be able to turn
the downrod counterclockwise with your hands. If in
doubt, tighten the set screw with the Allen wrench
until you cannot turn it any further.
CANOPY COVER
RING
MOTOR WIRES
(LEAVE AT LEAST
6" LONG)
PERMA•LOCK™
DOWNROD AND
BALL ASSEMBLY
HANGING
ADAPTER COVER
MOTOR
COUPLING
TAPERED
THREAD
MOTOR
HOUSING
ASSEMBLY
ALLEN SET
SCREW
Figure #4
CAUTION: Failure to fully lock in the
downrod before securely tightening the
Allen set screw may cause the fan to
separate from the downrod and fall during
normal operation.
ALLEN
WRENCH
ALLEN SET
SCREW
Figure #5
10
Holliston™
Fan Preparation - continued
Step 4e. Slide the hanging adapter cover down over
the motor coupling as shown in Figure #6, making
sure that the adapter cover is covering the motor
coupling as in shown Figure #7.
HANGING
ADAPTER
COVER
HANGING
ADAPTER COVER
CANOPY COVER
RING
MOTOR
COUPLING
Figure #7
Figure #6
LIGHTBULB INSTALLATION (uplight)
Install Lightbulbs:
LIGHTBULBS
Step 5. Insert the six 7-watt lightbulbs for the uplight
as shown in Figure #1.
(6) 7-watt
Uplight Bulbs
NOTE: When replacing these lightbulbs, be sure to
use only 7-watt maximum.
Figure #1
Hanging the Fan
Step 6a. To hang the fan body in the canopy, hold
the fan body firmly and insert the ball into the canopy
opening. Check that no wires are pinched. Rotate the
fan body until the slot in the ball fits into the pin opposite
the canopy opening.
BALL
Step 6b. Trim excess motor wires, leaving at least 6
inches above the downrod. Strip 1/2-inch insulation from
the end of each wire using a wire stripper (available at
your local hardware store).
SLOT
PIN
11
Canopy Electrical Connections
Step 7. Attach the fan wires to the ceiling fixture outlet box
wiring by placing the bare ends of the wires side by side
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
WIRE NUT
• GREEN leads from mounting plate and downrod assembly
of fan to GROUND conductor of power source. Secure
with wire nut.
2 BLACK WIRES
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLACK power wire from fan to BLACK power wire in
ceiling outlet box. Secure with wire nut.
2 WHITE WIRES
NOTE: If the color of your ceiling wires differs from that
described, consult an electrician.
3 GREEN WIRES
Canopy Hatch and cover ring Installation
Step 8a. Tuck the wires into the canopy with the
wire nuts pointed upwards, so that the WHITE and
BLACK wires are on opposite sides of the canopy
and all wires are clear of the canopy opening.
Step 8b. Install the canopy hatch with the last
canopy screw and lock washer using the provided
screwdriver. To do this, tilt the fan body away from
the hatch opening. Tighten the screws firmly.
Step 8c. Straighten the fan, then check to ensure
there is no movement between the canopy and the
ceiling or the Perma•Lock™ downrod and the ball
assembly.
Step 8d. Locate the locking pins
on the canopy cover ring as shown
in Figure #2. Lift up on the canopy
cover ring and guide the two (2)
locking pins into the two (2) locking
holes, then snap the canopy cover in
to place as shown in Figure #3.
CANOPY
CANOPY
HATCH
CANOPY
SCREW &
WASHER
Figure #1
CANOPY
COVER
RING
LOCKING
HOLES
LOCKING PINS
Figure #2
12
Figure #3
Holliston™
Blade Installation
Blade Hardware (not to scale)
Blades (5)
Blade Irons (5)
Blade Iron
Screws
Step 9a. Remove the five shipping blocks, and
screws as shown in Figure #2. DO NOT discard the
ten (10) screws; you will need them for installing the
blades onto the fan.
Attach Blade Irons
Step 9B. Attach a blade to a blade iron by first
pressing the blade iron onto the blade, then attaching
the blade iron using three blade screws and blade
washers as shown in Figure #3. Using the provided
screwdriver, tighten securely by hand only. Repeat
for each blade assembly.
Blade Installation
Washers (16)
Phillips
Screwdriver
Blade Screws (16)
SHIPPING
BLOCKS
SHIPPING BLOCKS
SCREWS
Step 9c. Before attempting to attach the blades,
review Figure #4 for blade placement on the flywheel.
The numbers and lines show screw placement when
attaching the five blade irons and blades assemblies
to the fan.
Figure #2
BLADE IRON
SCREWS
BLADE WASHER
BLADE
BLADE IRON
Figure #3
BLADE AND
BLADE HOLDER
FLYWHEEL
Figure #4
13
Blade Installation Continued
Step 10b. Attach a blade/blade iron assembly to the
flywheel by using two blade iron screws provided.
Place the end of the blade iron on the flywheel as
shown in Figure #5. Insert the screws one by one
using the provided screwdriver. Tighten securely by
hand only. Repeat for each blade/blade iron assembly
until all five blades are attached to the fan as shown
in Figure #6.
FLYWHEEL
Caution:
Blade screws must be tightened securely
before operating the fan.
Figure #5
Figure #6
LIGHT FIXTURE Installation (optional)
NOTE: If you are installing your fan without a light kit attached as below in Figure #1, continue with these installation
instruction Step 11a. If you have purchased a light kit for installation on your fan, skip this section and go to Step
13a on page 18 within this document.
Figure #1
14
Holliston™
switch housing and end cap Installation
NO LIGHT KIT - Installation:
SCREW
#8-32
SCREW PLUG
NOTE: If you are installing your fan without a light
kit attached as shown in Figure #1, continue with these
installation instruction
BOTTOM CAP
SCREW
#6-32
CAP
Figure #1
LIGHT KIT
PLATE
Switch Housing Hardware (not to scale)
Screw Plug
Figure #2
BOTTOM CAP
SCREW , #8-32
Light Kit Adaptor Assembly
Step 11a. Locate the light kit adaptor assembly and
screw plug as shown in the switch housing hardware
section above. You will need to install the complete
assembly for no light kit installation.
BOTTOM CAP
Figure #3
NOTE: Do not discard screws during
disassembly, all screws will be needed
for other installation steps within this
document.
CAP
Light Kit Adaptor Disassembly
Step 11b. Locate and remove the one #8-32
screw that is attaching the bottom cap to the light
kit adaptor assembly as shown in Figure #2 and
remove the bottom cap. Do not discard screws during
disassembly.
Cap SCREW,
#6-32
Figure #4
Step 11c. Locate and remove the four #6-32 screws
from the cap and remove the cap. Do not discard the
screws during disassembly.
NOTE: Locate the light kit adaptor as shown in Figure #2,
this adaptor plate will need to be attached to the fan during
fan installation for light kit or no light kit installation.
15
Switch Housing and Light Kit
Adaptor Installation: - ( NO LIGHT KIT)
Step 12a. Locate and remove the three #8-32
screws from the center shaft adapter located on
the bottom of the fan as shown in Figure #1. Do not
discard the screws, all three screws will be needed
for the next steps with in this document.
CENTER SHAFT
ADAPTER
ADAPTER SCREWS
, #8-32
Figure #1
Step 12b. Locate the light kit adaptor plate and
thread the BLUE and WHITE wires through the
hole in the center of the light kit adaptor plate, also
as shown in Figure #2.
LIGHT KIT
ADAPTOR
PLATE
WHITE
WIRE
Step 12c. Locate the three screws that you
removed from the center shaft adapter during Step
12a. These three screws are needed to attached the
light kit adaptor plate to the fan. Align the screw hole
on the light kit adaptor plate with the screw holes on
the center shaft adaptor and insert all three screws
as shown in Figure #3. Then tighten all three screws
with the provided screwdriver.
Figure #2
BLUE
WIRE
CENTER SHAFT
ADAPTER
LIGHT KIT
ADAPTOR
PLATE
SCREWS , #8-32
Figure #3
NOTE: Make sure that the wire nuts on the ends of
the WHITE and BLUE wires are securely attached
to the ends of the wires and that the wires are
tucked out of the way so that the wires are not
pinched when attaching the cap.
Step 12d. Locate the light kit adaptor plate cap as
shown in Figure #4 and align the four screw holes
on the cap with the holes on the light kit adaptor
plate. Using the four (4) screws that you removed
earlier from the light kit adaptor assembly (see step
11c), insert the four screws, attaching the cap to
the bottom of the fan. Then tighten all four screws
with the provided screwdriver.
WIRE NUTS
(WHITE and BLUE)
WIRES
CAP
SCREWS, #6-32
Figure #4
16
LIGHT KIT
ADAPTOR
PLATE
Holliston™
Switch Housing and Light Kit
Adaptor Installation - Continued ( NO LIGHT KIT)
Step 12e. Locate the bottom cap and screw as shown
in Figure #5, using the screw that you earlier removed
from the light kit adaptor assembly (see step 11c) and
insert cap screw through the hole in the center of the
cap and attaching the cap the bottom of the fan as
shown in Figure #5 on this page. Then tighten the
screw with the provided screwdriver.
BOTTOM
CAP
Step 12f. Locate the end cap screw plug shown in
Figure #6, align and insert the two (2) holding tabs
located on the screw plug with the slots located in the
center of the end cap, then press on the plug locking
end cap screw plug into place also as shown in Figure
#6 and Figure #7.
CAP SCREW
#8-32
Figure #5
PLUG
TABS
END CAP
SCREW
PLUG
Figure #6
END CAP
SCREW
PLUG
Figure #7
Switch Housing and Light Kit
Adaptor Installation ( NO LIGHT KIT ) - END
NOTE: To continue installation instruction,
go to (Inteli-Touch 3 - Control Installation)
within this document.
Figure #8
17
switch housing and end cap Installation
LIGHT KIT - Installation:
SCREW
#8-32
SCREW PLUG
NOTE: If you are installing your fan with a light kit
attached as below in Figure #1, continue with these
installation instruction Step 13a. Also you will need the
installation instructions that came with your new light
kit to complete the installation of the fan.
BOTTOM CAP
SCREW
#6-32
CAP
Figure #1
LIGHT KIT
ADAPTOR
Figure #2
Switch Housing Hardware (not to scale)
Switch Housing
Cap
Light Kit
Adaptor Assembly
Switch Housing
Cap Screw (2)
8-32 x 3/8
BOTTOM CAP
SCREW , #8-32
BOTTOM CAP
Step 13a. Locate the light kit adaptor assembly and
screw plug as shown in the switch housing hardware
section above. You will need to disassemble and use
parts from the light kit adaptor assembly for adding a
light kit to your fan.
Do not discard screws during disassembly,
all screws will be needed for other installation
steps within this document.
Figure #3
CAP
Light Kit Adaptor Disassembly
Step 13b. Locate and remove the #8-32 screw that
is attaching the bottom cap to the light kit adaptor
assembly as shown in Figure #3 and remove
the bottom cap. Do not discard screws during
disassembly.
Cap SCREW,
#6-32
(Screws 4)
Figure #4
Step 13c. Locate and remove the four (4) #6-32
screws from the cap as shown in Figure #4 and
remove the cap. Do not discard screws during
disassembly.
NOTE: Locate the light kit adaptor as shown in Figure
#5, this adaptor plate will need to be attached to the fan
during fan installation, installation instructions continued
on the next page of this document.
LIGHT KIT
ADAPTOR
Figure #5
18
Holliston™
Switch Housing and Light Kit
Adaptor Installation: - Continued ( LIGHT KIT)
Step 14a. Locate and remove the three (3) #8-32
screws from the center shaft adapter located on the
bottom of the fan as shown in Figure #6.
CENTER SHAFT
ADAPTER
ADAPTER SCREWS,
#8-32
(Screws 3)
Figure #6
Step 14b. Locate the light kit adaptor plate as shown
in Figure #7 and thread BLUE and WHITE wires
through the hole in the center of the light kit adaptor
plate, also as shown in Figure #7.
LIGHT KIT
ADAPTOR
PLATE
WHITE
WIRE
Figure #7
Step 14c. Locate the three (3) screws that you
removed from the center shaft adapter during Step
14a, these three screws are needed to attached the
light kit adaptor plate to the fan. Align the screw hole
on the light kit adaptor plate with the screw holes on
the center shaft adaptor and insert all three (3) screws
as shown in Figure #8. Then tighten all three screws
with the provided screwdriver.
BLUE
WIRE
CENTER SHAFT
ADAPTER
LIGHT KIT
ADAPTOR
PLATE
SCREWS , #8-32
(Screws 3)
Figure #8
Step 14d. Locate the light kit adaptor plate cap as
shown in Figure #9 and thread BLUE and WHITE
wires through the hole in the center of the light kit
cap, also as shown in Figure #9
CAP
WHITE
WIRE
BLUE
WIRE
Figure #9
19
Switch Housing and Light Kit
Adaptor Installation: - Continued ( LIGHT KIT)
Step 14e. Align the four screw holes on the cap with
the holes on the light kit adaptor plate, using the four
(4) screws that you earlier removed from the light kit
adaptor assembly (see step 11c) and insert the four
(4) screws, attaching the cap to the bottom of the fan
as shown in Figure #10 on this page. Then tighten all
four (4) screws with the provided screwdriver.
NOTE: Locate and open the box for the light kit that
you are installing on the fan and locate the installation
instructions. If the installation instructions refer to
attaching the light kit by screwing the center stem in
to the bottom of the fan, switch housing cap or that
the light kit is mounted by screw the center stem into
the bottom of the fan, it may look like the light kit as
shown in Figure # 12. You will need to use the switch
housing cap that has been provided in the box as
shown in Figure #11 during the installation of the light
kit. Otherwise, skip to step 14g.
Step 14f. Locate the switch housing cap as shown in
Figure #11. Then attach the light fixture to the switch
housing cap by first threading the BLACK and WHITE
wires through the hole in the center of the switch
housing cap, also as shown in Figure #13, and then
screw the light kit fixture to the bottom of the switch
housing cap by screwing the center stem of the light
fixture into the bottom switch housing cap as shown
in Figures # 13 and #14. Secure the light kit to the
switch housing by placing the lock washer and hex
nut you removed from the light kit onto the center
stem and screw on firmly.
WHITE
WIRE
Figure #10
CENTER STEM
CENTER STEM
LIGHT KIT
Figure #11
SWITCH HOUSING
CAP
Figure #12
BLACK AND WHITE WIRES
HEX NUT
CENTER STEM
LOCK WASHER
SWITCH HOUSING
CAP
SWITCH HOUSING
CAP
CENTER STEM
LIGHT FIXTURE
{Example Photo}
BLACK AND WHITE WIRES
LIGHT FIXTURE
{Example Photo}
Figure #13
Figure #14
Holliston™
Switch Housing and Light Kit
Adaptor Installation: - Continued ( LIGHT KIT)
Step 14g. Connect the wires of the motor to the
wires of the light fixture. Connect the BLUE wire from
the motor to the BLACK wire of the light fixture and
connect the two WHITE wires together, as shown in
Figure #15. Secure the connection using the wire
nuts.
BLUE AND
WHITE WIRES
WIRE NUT
BLACK AND WHITE WIRES
LIGHT FIXTURE
{Example Photo}
Step 14h. Align the two (2) posts on the light kit
assembly and the two (2) holes located on the switch
housing cap as shown in Figure #16 and insert the
posts on the light kit assembly into the two (2) holes
on the light kit adaptor plate cap as shown in Figure
#16.
Figure #15
TWO (2)
SCREWS
HOLES
TWO (2)
SCREW
HOLES
TWO (2)
POST
Figure #16
Step 14h. Locate the two (2) switch housing cap
screws as shown in Figure #17. Then attach the light
fixture to the switch housing on the bottom of the fan
as shown in Figure #17 and tighten the screws with
the provided screw driver.
Switch Housing
Cap Screw (2)
8-32 x 3/8
Step 15i. At this time locate and continue the
installation of the light kit by using the installation
instructions that were provided within the box with the
light kit. Once the light kit has been installed return to
the next section (WALL CONTROL PREPARATION)
of this document. You will need to install the wall
control (W-84) and learn how to operate the fan and
light on the Holliston fan.
SWITCH HOUSING
Switch Housing
Cap Screw (2)
8-32 x 3/8
LIGHT FIXTURE
{Example Photo}
Figure #17
21
®
3
W-84 WALL CONTROL INSTALLATION
(For use on product with BOTH UP and DOWN LIGHTS ONLY)
W-84 Wall control Preparation
WALL CONTROL AND Hardware (not to scale)
Switch Mounting
Screws (2)
W-84
Wall Control
Switch Bezels
(1) White (pre-installed)
(1) Almond
White Wall
Plate (1)
Almond Wall
Plate (1)
Wall Plate Screws
(2) White
(2) Almond
Prepare for W-84 Wall Control Bezel replacement
as follows:
(4) Wire Cap
BEZEL
Before installing the W-84 wall control you will need to
check and see if you will need to change the bezel on
the front of the wall control from WHITE to ALMOND.
If you are going to use white, skip these steps and go
to wall control installation starting on page 24. If you
are going to use the ALMOND bezel and wall plate
you will first need to change the bezel on the front of
the switch before installing the switch in to the wall.
Step 1a. Locate the four (4) tabs holding the bezel to
the front of the switch, then press in on each tab one at
a time, removing the bezel as shown in Figure #1.
Step 1b. Locate the rubber key pad attached to the
four (4) locating pins as shown in Figure #2 and
remove rubber key pad from the WHITE bezel, also
as shown in Figure #2.
BEZEL
TABS
Figure #1
Step 1c. Reinstall the rubber key pad on to the four
(4) locating pins located on the almond bezel as
shown in Figure #3.
WHITE
BEZEL
ALMOND
BEZEL
LOCATING
PINS (4)
LOCATING
PINS
HOLES(4)
RUBBER KEY
PAD
Figure #2
22
RUBBER KEY
PAD
Figure #3
®
3
RUBBER KEY
PAD
Prepare for W-84 Wall Control installation Continued
Step 1d. Before attaching the bezel back on to the
front of the switch, make sure that the rubber key
pad is attached to the locating pins on the bezel as
shown in Figure #4.
LOCATING
PINS
(4)
ALMOND
BEZEL
Figure #4
ALMOND
BEZEL
Step 1e. To attach the bezel back onto the front of the
switch you will need to align the four (4) tabs on the
bezel with the front of the wall control.Gently press
on both top and button of the bezel at the same time,
snap the bezel back on to the front of the switch as
shown in both figures #5 and #6.
BEZEL
TABS
BEZEL
ALIGNMENT
PIN AND HOLE
Figure #5
ALMOND
BEZEL
Step 1f. Check your work by pressing on the light,
fan, reverse and power buttons, making sure that the
buttons do not stick and that each switch functions
properly.
BEZEL
TABS
Figure #6
23
®
3
w-84 Control INSTALLATION
Installing the W-84 Wall Control
NOTE: W-84 Wall Control should only be installed on Casablanca's Inteli-Touch® 3 fans with UPLIGHTS ONLY
or both an UPLIGHT and a DOWNLIGHT on the fan.
The wall control installs in the same manner as an ordinary light switch, using an existing wall box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this
reason the following precautions must be observed:
1. Use only the Casablanca W-84 wall control.
2. Do not use any additional control with your InteliTouch 3 fan (for example, dimmer, or fan speed
control).
3. Do not use more than one fan per wall control.
4. No other light fixtures or electrical appliances
may be connected on the circuit controlled by
the W-84 wall control.
single W-84 Installation
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting installation.
W-84 is used to describe either white (-11) or almond finish.
If you have multiple Inteli-Touch® 3 fans, refer to the section
"Changing Frequency Setting" on page 6.
1.Remove the screws and switch plate from the existing
switch box.
2.Remove the screws holding the switch in the switch
box.
3.Pull the existing switch from the switch box to expose
the wire connections.
4.Remove the two wires from the switch.
5.Connect the BLACK wire from the POWER SOURCE
that you just removed from the switch to the BLACK/
WHITE STRIP wire on the W-84 wall control. Secure
this connection with a wire nut.
6.Connect the second BLACK wire that you just removed
from the switch to the second BLACK wire on the
located on the back of the W-84 wall control. Secure
this connection with a wire nut.
(FIGURE #1)
7.Connect the green ground wire coming from the back
of the W-84 control to the ground wire in the switch box.
Secure the splice with a wire nut.
2 BLACK
WIRES
W-84
Wall Control
NOTE: The RED wire is not used in this
application. DO NOT remove the crimped cap
from the wire.
8.C heck your work by using the wiring
diagrams as shown in Figures # 1 and
#2.
RED WIRE
NOT USED
9. Install the W-84 in the wall box with the
two long screws provided.
10. Install the wall plate with the two colormatched screws.
(FIGURE #2)
24
BLACK AND WHITE
STRIPED WIRE
®
3
dual W-84 Installation
To control the fan and lights from two locations (a three-way circuit), use two
W-84 wall controls as shown in the wiring diagram in Figure #1. Before
installing the two switches into the wall, place both switches side by
side, then locate the 4 dip switches on the side of the two switches as
shown in Figure #2. Then make sure that the dip switches are set to the
same address on both switches as shown in Figure #2. When setting
these dip switches you are setting the channel number that is required
to control both your fan and lights from both sides of the room. If you are
installing other Inteli-Touch® 3 fans within your home you may need to
reset the dip switches on these other fans to a different channel before
installing your W-84 wall control into the wall. Please review the section
on channel changing within this part of the operation manual as shown
on page #27.
DIP SWITCHES
(FIGURE #2)
CAUTION!
Ensure power is turned OFF at the breaker or fuse panel before starting installation.
NEUTRAL
WHITE
GREEN
BLACK
BLACK
BLACK WITH
WHITE STRIPE
GREEN
GREEN
W-84
BLACK WITH
WHITE STRIPE
W-84
RED
(FIGURE #1)
BLACK
BLACK
RED
RED
BLACK
BLACK
RED
120V AC
BLACK
To control the fan and lights from two
locations (a three-way circuit), use two
W-84 wall controls.
1.Remove the screws and switch plate from the existing
switch box and the screws holding the switch in the switch
box.
2.Pull the existing switch from the switch box to expose the
wire connections.
3.Determine which wire is connected to the common
terminal from the power source (120V AC) of the
three-way switch. (The terminal will be marked on
switch).
BLACK
4.Remove the wire from the common terminal of the three-way switch.
Connect this wire to the remaining black/white striped wire on the
W-84 control. Secure this splice with a wire nut.
5.Remove the two remaining wires from the three-way switch.
Connect the black wire of these wires to a black wire on the
W-84 control. Secure the splice with a wire nut. The remaining
red wire is to be connected to the other red wire on the
W-84. Secure the splice with a wire nut.
6.Connect the green ground wire coming from the back of the W-84
control to the ground wire in the switch box. Secure the splice with
a wire nut.
7.Check your work by using the wiring diagrams as shown in Figures
# 1 and #3 on this page.
8.Install the W-84 in the wall box with the two long screws provided.
9.Install the wall plate with the two short color-matched screws
provided.
10.Installation of the second W-84 control is identical. Repeat steps
1 through 7.
2 BLACK
WIRES
W-84
Wall Control
2 RED WIRES
BLACK AND WHITE
STRIPED WIRE
(FIGURE #3)
25
®
3
Operation Power
The
button is normally left in the on position. Always turn the power off
during cleaning or servicing the fan and during thunderstorms. It is also used to
exit or enter additional programs.
The
button must be left on to retain a previously set fan speed or light
level.
Operation Speed Control
There are six individual speed settings for the fan; each speed is indicated
by an audible tone of increasing pitch.
Fan Control
ON - OFF:
To select the desired fan speed:
A
momentary
1. With fan off, press and hold the button labeled
. The fan blades
press of the FAN
will start rotating at the slowest speed, and will increase in steps.
button
2. Release the button when the desired speed is reached.
Change
The fan speed is now in memory and will automatically come on at the
speed:
same speed each time the
button is used. To maintain this level Press and hold
of speed, turn the fan on by pressing
less than one second. To
FAN button
longer than one
lower speed, turn fan off, then on by pressing and holding the
second
button until the desired speed is reached. When the fan is on, you may
increase the speed by pressing and holding the
button until the
desired speed is reached, then release it.
Operation Reversing Airflow
The direction of airflow can be changed from downward to upward or from upward to downward.
To reverse the airflow:
1. Make sure the
is on and blades are Turning.
2. Press the
button.
Note: A four-toned signal
indicates the command was
accepted by the fan. A few
seconds later the fan will slow
to a stop and then reverse
direction.
Operation lights
To turn the lights off and on, press and release the
button for less than
one second.
1. First press/release of the
button- Both lights shall turn ON.
2. Second press/release of the
button- Both lights shall turn OFF.
3. Third press/release of the
button – Downlight turns ON only.
4. Fourth press/release of the
button – Downlight turns OFF.
5. Fifth press/release of the
button – Uplights turns ON only.
6. Sixth press/release of the
button - Uplights turns OFF only.
To vary the light brightness at each touch level:
Make sure where you are in the sequence to the right.
To dim both lights at the same time:
1. Make sure you have the uplight on.
2. Turn the light off, then press and hold the
button. After one second, both
lights will come on at their lowest setting and gradually become brighter or dimmest level if you continue holding the
button.
3. Release the
button when the desired brightness is reached.
26
Light Control
ON - OFF:
A momentary press of the
LIGHT button
Change brightness:
Press and hold
LIGHT button longer than one
second
®
3
Operation lights
To dim just the up light:
1. Make sure you have just the downlight on.
2. Turn the light off, then press and hold the
button. After one
second, the up light will come on at their lowest setting and gradually
become brighter or dimmest level if you continue holding the
button.
3. Release the
button when the desired brightness is reached.
NOTE: Light Operation the light varies from “bright”
to “dim” over approximately
8 seconds. This sequence
will reverse the light when
it reaches the brightest
or dimmest level if you
continue to hold the LIGHT
button. Release the button
when the desired level is
reached.
To dim just the down light:
1. Make sure you have both lights on.
2. Turn the light off, then press and hold the
button. After one
second, down light will come on at their lowest setting and gradually
become brighter or dimmest level if you continue holding the
button.
3. Release the
button when the desired brightness is reached.
changing frequency setting
NOTE: All fans leave the factory set to
“1111”
DIP
SWITCHES
You will only have to change the dip switch settings in the remote if you
are using more than one fan in the same area and want to control them
separately.
NOTE: DO NOT set dip switch setting in the remote
to ‘0000’, this may cause frequency interference from
other Casablanca Products.
(Figure 1)
Step 1. Turn power OFF at the circuit breaker or fuse box and at the toggle
switch, for the fan you want to change.
Step 2. Remove the screws and switch plate from the existing switch box.
Step 3. Remove the screws holding the switch in the switch box.
Step 4. Pull the existing W-84 switch from the switch box to expose the dip
switches located on the side of the control as shown in Figure #1.
DIP SWITCHES
SET TO ‘1111’
(Factory Setting)
DIP SWITCHES
SET TO ‘1001’
Step 5. Change the dip switch settings, assuring that they are different from
the previously installed Inteli-Touch® 3 fan.
Step 6. Mount the W-84 Wall Control unit back into the wall electrical box.
Step 7. At the circuit breaker or fuse box and at the toggle switch, turn the
power off for the fan whose frequency you are changing.
Step 8. Within 20 seconds of restoring power to the ceiling fan and the W-84
Wall Control press and hold both the “FAN” and “REVERSE” buttons as
shown in Figure #2. For 3 seconds, you will hear one tone from the Piezo
Buzzer indicating the command has been accepted.
(Figure 2)
27
®
3
Automatic Demonstration Program
Programmed into every Inteli-Touch® Series fan is an
Automatic Demonstration Program. It can be used to
fully demonstrate and test the operation of the fan.
To enter the demonstration program:
1.Turn
off for at least 5 seconds. This will
clear the fan memory ready for programming.
2.Turn
on.
3.Immediately operate the buttons in the following
sequence:
+
+
+
+
A multi-tone signal will verify the start of the test program which proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan turns off with audio tones (blades coast for a
short time).
• Lights turn off.
The complete cycle lasts slightly over one minute. It
will continue to repeat until the
is turned off
for more than five seconds, cancelling the program.
Operation Safe-Exit® and light-minder® Program
NOTE: Both Light-Minder and Safe-Exit programs will always run at the same
time.
Safe-Exit
The Safe-Exit Program gives you about thirty seconds of light when you turn the lights off, enabling you to exit your
home before the lights go out. To enter the Safe-Exit Program:
1) To operate the lights for Safe-Exit Program – Press the
button off for at least five seconds.
2) Turn the Power on. Immediately press the buttons in the following sequence:
+
+
+
.
The
Button should be immediately press after an audio tone is heard from the fan controller. The lights shall
blink to indicate this command has been accepted. The lights shall stay on for 30 seconds and then begin to dim.
After thirty seconds have elapsed, the lights shall be completely off.
3) To cancel the Safe-Exit Program, press the
button off for five seconds.
NOTE: If the lights are left on in the room, the lights will automatically turn OFF after 2
hours. ( this is Light-Minder)
The Light-Minder Program automatically turns OFF the fan mounted lights after two
hours.
To enter the Light-Minder Program:
1) To operate the lights for Light Minder Program – Press the
button off for at
least 5 seconds.
2) Turn the
on. Immediately press the buttons in the following sequence:
+
+
+
. A series of tones will be heard through the piezo-buzzer
indicating the command has been accepted. Once the lights turn on, they will automatically turn off after 2 hours.
3) Light operation still remains normal, if you leave the room and turn OFF the lights
will blink to indicate this Safe-Exit command has been accepted. The lights will stay
on for 30 seconds and then begin to dim. After thirty seconds have elapsed, the lights
will turn completely off.
4) To cancel the Light-Minder and Safe-Exit Programs, press the
button.
28
Light-Minder
®
3
Operation Home-Safe® Program
The Home-Safe Program makes an unoccupied home appear occupied by turning
the lights on and off at random times.
To enter the Home-Safe Program:
1) To operate the lights and fan for Home Safe Program – Press the
Button off for a least 5 seconds.
2) Turn the
on. Immediately press the buttons in the following sequence:
+
+
+
. A series of tones will be heard through the
piezo-buzzer and flashing lights indicating the command has been accepted will
follow. This program overrides all manual control of lights and fan. Once the lights
turn on, they will automatically turn off after 2 hours.
3) The lights will automatically cycled on and off in a controlled sequence as follows: ON 1 hour, OFF ½ hour, ON 2 hours, OFF 1 hour, ON ½ hour then OFF 2
hours. This seven hour pattern will repeat continuously so that a different pattern
of lighting is seen each day of the week.
4) To cancel the Home-Safe Program, press the
Button OFF for five
seconds.
Operation Fan-Minder™ Program
The Fan-Minder feature will add to your comfort when used in the bedroom. The program
reduces the speed of the fan each two-hour interval to compensate for cooling night air.
To enter the Fan-Minder Program:
1. Turn the
OFF for at least 5 seconds.
2. Turn the
ON.
3. Immediately operate the buttons in the following sequence:
+
+
+
4. The fan will respond with three descending tones. A timer is now initiated and the fan will
reduce one speed for each two-hour interval. The fan will not, however, descend below
the first or the lowest speed.
5. You may increase the fan speed by pressing and holding the
button until the
desired speed is reached, then release it. The fan will again reduce one speed for each
2 hour interval.
5. To cancel the Fan-Minder Program, turn the
OFF for three seconds.
29
®
3
In the wall bezel replacement
WALL CONTROL AND Hardware (not to scale)
Switch Mounting
Screws (2)
W-84
Wall Control
Switch Bezels
(1) White
(1) Almond
White Wall
Plate(1)
Almond Wall
Plate(1)
Wall Plate Screws
(2) White
(2) Almond
(4) Wire Cap
Warning!
To avoid possible electrical shock, make certain that electricity is turned off at the circuit
breaker or fuse box before attempting any installation or repair procedure
SCREWS
(2)
CAUTION! NOT turning the power OFF at the
circuit breaker or fuse box may cause damage
to the electronics within the wall control and/
or the PC board on the fan.
White Wall
W-84 Wall Control Bezel Replacement installation
as follows - (In the Wall Replacement):
Figure #1
Step 1a. Locate the two (2) screws holding the switch
plate to the wall control and remove the cover plate
as shown in Figure #1.
BEZEL
Step 1a. Locate the four (4) tabs holding the bezel to
the front of the switch, then press in on each tab one at
a time, removing the bezel as shown in Figure #2.
Step 1b. Locate the rubber key pad attached to the
four (4) locating pins as shown in Figure #2 and
remove rubber key pad from the WHITE bezel, also
as shown in Figure #2.
BEZEL
TABS
Figure #2
30
Holliston™
W-84 Wall Control Bezel replacement:
CONTINUED
WHITE
BEZEL
-
Step 1c. Locate the rubber key pad attached to the
four (4) locating pins and remove rubber key pad
from the WHITE bezel, also as shown in Figure
#3.
LOCATING
PINS (4)
LOCATING
PINS
HOLES(4)
RUBBER KEY
PAD
Figure #3
Step 1d. Reinstall the rubber key pad on to the
four (4) locating pins located on the almond bezel
as shown in Figure #4.
ALMOND
BEZEL
RUBBER KEY
PAD
Figure #4
Step 1e. Before attaching the bezel back onto the
front of the switch, make sure that the rubber key
pad is attached to the locating pins on the bezel as
shown in Figure #5.
RUBBER KEY
PAD
LOCATING
PINS
(4)
ALMOND
BEZEL
Figure #5
31
W- 8 4 Wa l l C o n t r o l B e z e l r e p l a c e m e n t :
CONTINUED
BEZEL
-
Step 1e. To attach the bezel back on to the front of the
switch you will need to align the four (4) tabs on the bezel
with the front of the wall control and by gently pressing on
both top and bottom of the bezel at the same time, snap
the bezel back on to the front of the switch as shown in
both figures #6.
BEZEL
TABS
BEZEL
ALIGNMENT
PIN AND HOLE
Figure #6
Step 1f. Re-attach the wall plate using the two (2) almond
screws as shown in Figure #7. Check your work by
pressing on the light, fan, reverse and power buttons,
making sure that the buttons do not stick and that each
switch functions properly. Turn the power back ON and
test the fan and lights.
ALMOND
WALL PLATE
SCREWS
ALMOND
COLORED
BEZEL
ALMOND
COLORED
WALL PLATE
Figure #7
32
Holliston™
Troubleshooting tips
Please refer to this troubleshooting guide before requesting service or contacting your dealer for assistance.
PROBLEM
Fan will not start
POSSIBLE REMEDIES
• Check the main circuit fuses, circuit breakers, and wall switch position.
Check all wire connections. Make sure the power is turned off during this
inspection.
• Pin connectors are not making good contact. Check all connections.
• The fan receiver is defective. Replace the fan receiver.
• Reset the frequency setting: Turn the power off at the circuit breaker
for the fan that is not functioning only. Within 20 seconds from restoring
power to the ceiling fan and the W-84 Wall Control press and hold both
the “Fan” and “REVERSE” buttons as shown in Figure #2 for 3 seconds,
you will hear one tone from the Piezo Buzzer indicating the command
has been accepted. The Fan will come on at “low” speed in the reverse
direction. into the slot on the ball.
• Check that the blade holders have not been bent during installation and the blades
are balanced.
• The hanger bracket and/or the ceiling outlet are attached too loosely. Make sure
the hanger bracket is attached tightly to the ceiling outlet box and the downrod
assembly is secured firmly.
• The downrod is attached to the downrod base too loosely. Make sure all the
screws are securely tightened.
Fan is noisy during operation
• When changing fan speeds, you may hear several audible clicks. This is normal
operation.
• Check and tighten the light fixture retaining screws, glass shade screws, and/or
lightbulb(s).
• Tighten the canopy screws and mounting plate assembly. Make sure the wire
nuts inside the canopy and switch housing are not touching the metal parts and
that they have not fallen off the wire splices. Tighten as necessary.
• Tighten the blade holders to the flywheel (or Direct Drive motor) and the blades
to the bladeholder screws.
• Make sure all the screws in the motor housing are snug but not overly tight.
Fan does not run on low speed
• If fan is new, it may need to be “broken in.” Run at high speed for several days.
This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures: Reorient or relocate the receiving antenna, Increase the separation between the equipment and receiver, Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or
modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control.
33
Care Recommendations
Fan Finishes
• For cleaning, a soft brush or lint-free cloth should be used to prevent scratching the finish.
• A vacuum cleaner brush nozzle can remove heavier dust.
• Surface smudges or an accumulation of dirt and dust can be removed easily using a mild detergent and slightly
dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will
damage the finish.
Blades
• Wood-finish blades should be cleaned with a furniture polishing cloth. Occasionally, a light coat of furniture polish
may be applied for added protection and beauty.
• For painted and high-gloss blades, surface smudges or an accumulation of dirt and dust can be removed easily
using a mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive
cleaning agents as these will damage the finish.
No Need for Lubrication
• Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings
that are lubricated for life.
• Do not attempt to oil the motor.
Changing Lightbulbs
• Be sure to turn the power to OFF at the wall switch or circuit breaker before changing lightbulbs.
• Replace bulbs with the same type as you removed from the light fixture.
For questions or to locate the nearest Casablanca Authorized Service Center
call toll free: 1-888-227-2178
or visit us on the web at: www.casablancafanco.com
Product Specifications
Model Name:
Holliston
Model Number: C31UxxZ
Dimensions:
A = 12"
B =13.5"
C = 3"
D =13.9"
E = 7"
Weight:
26 lbs.
34
Motor:
XLP Plus™
Blade Span:
60"
Blade Iron Pitch: 15°
No. of Blades:
5
Technology:
Inteli-Touch® 3 W-84
Lightbulbs:
(6) 7-Watt C7
Airflow:
6495 cfm
Electricity Use: 115 watts
Airflow Efficiency:56.5 cfm/watt
Holliston™
35