Axor Phoenix 17104XX1 Specifications

Installation Instructions / Warranty
13444181
Four-hole Roman Tub Rough
13444181
13444181
SecuboxTM
Technical Specifications
Operating pressure:
Recommended operating pressure:
Hot water temperature:
Recommended hot water temperature:
Connections:
Rate of flow:
max. 145 psi
14.5 - 72.5 psi
max. 176° F*
120° F - 140° F*
cold right - hot left ½"
approx. 5.8 gpm
This unit is listed by UL.
*Please know and follow all applicable local plumbing codes when setting the
temperature on the water heater. In Massachusetts, the water heater may be
set no higher than 112oF.
Installation Considerations
This unit includes a cutout template, which must be used. Custom installations may require additonal parts which cannot be furnished by Hansgrohe.
This unit must be completed with a trim kit. The handshower must be installed.
Protection against back siphonage is provided by a check valve (included with the trim kit) and by
an automatically resetting diverter (included with the trim kit).
Important: If Axor Citterio trim kit 39452XX1 or 39456XX1 is to be used, this rough must
be installed with mounting plate 39449001 (not included).
To insure proper fit of the trim, the surface material (tile, etc) must be installed prior to installation
of this rough.
2
Available trim kits (not included)
Axor Starck
10454XX1
Axor Starck
10444XX1
Axor Citterio
39452XX1
Axor Citterio
39453XX1
Axor Citterio
39454XX1
Axor Citterio
39456XX1
Axor Steel
35444801
Axor Uno
38447XX1
Axor Montreux
16544XX1
Axor Terrano
37447XX1
Axor Terrano
37547XX1
Axor Carlton
17454XX1
Axor Carlton
17455XX1
Axor Phoenix
17446XX1
Axor Phoenix
17447XX1
mounting plate 39449001
required
mounting plate 39449001
required
3
Installation
Position the template on the mounting surface (1). Drill the
holes according to the template (2).
Make sure that there is sufficient space under the mounting
surface for the Secubox.
Wrap the threads on the hoses included with this kit with
Teflon thread tape. Install them on the diverter housing.
Install the mounting nuts, metal washers, and friction washers on the hot and cold valves. From below the mounting
surface, push the valves up through the holes.
4
From above the mounting surface, install the stop ring and
mounting plate on the valve (1). The stop ring wll stop the
mounting plate at the correct height. Lower the valve so that
the mounting plate rests on the mounting surface (2).
Tighten the mounting nuts (1). Tighten the tensioning screws
(2).
Install the mounting nut, metal washer, and friction washer
on the diverter housing (1). Omit the white plastic spacer
unless the mounting surface is thin. From below the mounting
surface, push the diverter housing up through the hole in the
mounting surface.
From above the mounting surface, install the sealing gasket
and spout base on the tee as far as the spout base will go
without forcing it (2). Lower the diverter housing so that the
spout base rests flat on the sealing ring and mounting surface, and the retaining pin goes through the its hole.
5
Tighten the mounting nut (1). Tighten the tensioning screws
(2).
Install the connecting hoses on the valve outlet ports.
Place the Secuflex holder in its hole on the mounting surface
(1). Turn it so that the positioning pin is on the side away
from the bather.
Install the mounting nut, metal washer, and friction washer
(2). If the mounting surface is thin, install the spacers as
well.
Tighten the mounting nut (3). Tighten the tensioning screws
(4).
6
Connect the hot and cold supply lines (not included) (1).
Push the Secuflex hose down through the holder (2).
Install the plug on the spout base (1).
Remove the plug from the high pressure hose (2).
Turn the water on and flush the unit (3).
Turn the water off.
Replace the plug on the high pressure hose (1). Pressure test
the unit (2). Check all connections for leaks.
7
Push the Secuflex hose over the end of the high pressure hose
(1). Tighten the nut (2).
Install the plaster shields on the valves, diverter housing, and
handshower holder to protect the unit until construction is
complete and the trim is installed.
Install the Secubox. Cut it if necessary to make a good fit.
Mark the positions of the screw holes. Drill the holes with a 6
mm bit. Secure the Secubox to the floor with the screws.
8
Replacement Parts
6
11
13
5
1
2
1
2
3
4
5
6
7
8
9
10
11
cartridge
stop valve
Secuflex hose
connecting hose
handle fixing set
fixing set for Secuflex
nut for Secuflex
fixing set for stop valve
fixing set for diverter hsg
pressure hose
diverter housing
SecuboxTM
94149000
92944000
94108000
94174000
94184000
96072000
96074000
96078000
96080000
96565000
96125000
28389000
9
4
7
10
3
9
Cleaning Recommendation for Hansgrohe Products
Modern faucetry and shower products utilize a combination of materials to comply with the needs of the
market with regard to design and functionality.
To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment
is not covered under the Hansgrohe warranty.
Cleaning Materials for Faucets and Showers
•
•
•
•
To remove lime scale, use only products made specifically for that purpose. Always follow the
manufacturer’s instructions when using.
Do not use cleaners that contain hydrochloric, formic, acetic, or phosphoric acids, as these will cause
considerable damage to finishes and to plastic components.
Never mix cleaning materials.
Never use cleaners containing abrasives. Do not use abrasive cleaning cloths, pads, or sponges.
Cleaning Procedures
•
•
•
•
Clean your faucets and shower products as and when required. Regular cleaning will prevent scale
buildup and water spotting.
Follow the label instructions. Do not allow any cleaner to remain on the product for longer than
necessary.
When using spray cleaners, spray first onto a sponge or cloth – do not spray directly onto the product.
After cleaning, rinse thoroughly with clear water to remove any cleaner residue.
Important
•
Soap and shampoo residue can also cause damage to the product. Rinse well with clean water after use.
•
If the surface is already damaged, harsh cleaning materials will cause further damage.
Limited Lifetime Consumer Warranty
This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to
Hansgrohe products which are purchased by a consumer in the United States after March 1, 1996, and installed in either the United States or
Canada.
WHO IS COVERED BY THE WARRANTY
This warranty extends to the original consumer purchaser only.
WHAT IS COVERED BY THE WARRANTY
This warranty covers only your Hansgrohe manufactured product. Hansgrohe warrants this product against defects in material or workmanship
as follows: Hansgrohe will repair at no charge for parts only or, at its option, replace any product or part of the product which proves defective
because of improper workmanship and/or material, under normal installation, use, service and maintenance. If Hansgrohe is unable to provide a
replacement and repair is not practical or cannot be timely made, Hansgrohe may elect to refund the purchase price in exchange for the return of
the product.
LENGTH OF WARRANTY
Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a
consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for as long as you own
the product and the home in which the product is installed. If you purchased the product for use primarily for any other purpose, including, without
limitation, a commercial purpose, this warranty extends only (i) for 1 year, with respect to Interaktiv and Retroaktiv products, and (ii) for 5 years,
with respect to AXOR, ShowerPower and Pharo products.
10
THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR:
A.
Conditions, malfunctions or damage not resulting from defects in material or workmanship.
B.
Conditions, malfunctions or damage resulting from (1) improper installation, improper maintenance, misuse, abuse, negligence, accident
or alteration, or (2) the use of abrasive or caustic cleaning agents or “no rinse” cleaning products, or the use of the product in any manner
contrary to the product instructions.
C.
Labor or other expenses for the disconnection or return of the product for warranty service, or for installation or reinstallation of the product.
D.
Accessories or related products not manufactured by Hansgrohe.
TO OBTAIN WARRANTY SERVICE
Contact your Hansgrohe retailer, or write to Technical Service at:
Hansgrohe Inc.
1492 Bluegrass Lakes Parkway
Alpharetta GA 30004
Or, call Hansgrohe toll-free at (800) 334-0455.
In requesting warranty service, you will need to provide
1.
2.
3.
The sales receipt or other evidence of the date and place of purchase.
A description of the problem.
Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 1492 Bluegrass Lakes
Parkway, Alpharetta, Georgia 30004, Attention: Technical Service, if required by Hansgrohe.
When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.
EXCLUSIONS AND LIMITATIONS
REPAIR OR REPLACEMENT (OR, IN LIMITED CIRCUMSTANCES, REFUND OF THE PURCHASE PRICE) AS PROVIDED UNDER THIS WARRANTY IS
THE EXCLUSIVE REMEDY OF THE PURCHASER. HANSGROHE NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO CREATE FOR IT ANY
OBLIGATION OR LIABILITY IN CONNECTION WITH THIS PRODUCT.
HANSGROHE SHALL NOT BE LIABLE TO PURCHASER OR ANY PERSON FOR ANY INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES,
ARISING OUT OF BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY).
Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to
you.
This warranty gives you specific legal rights, and you may have other rights which vary from State to State.
You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court
against us under the Magnuson-Moss Warranty Act.
PRODUCT INSTRUCTIONS AND QUESTIONS
Upon purchase or prior to installation, please carefully inspect your Hansgrohe product for any damage or visible defect. Prior to installing, always
carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If you have questions at any time
about the use, installation, or performance of your Hansgrohe product, or this warranty, please call or write to us at the toll-free number and address
printed above.
11
www.hansgrohe-USA.com
US - Installation Instructions • Part No. 90727503 • Revised 12/2006
Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004
Tel. 770 360-9880 • Fax 770 360 9887