Miele T 8861 WP Edition 111 Operating instructions

Operating instructions
for heat pump tumble dryer
T 8861 WP Edition 111
To avoid the risk of accidents or
damage to the appliance, it is
essential to read these instructions
before it is installed and used for the
first time.
en - AU, NZ
M.-Nr. 09 402 480
Caring for the environment
Disposal of the packing
material
The packing material protects the
tumble dryer from transport damage.
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Rather than just throwing these
materials away, please ensure they are
recycled.
Disposing of your old
appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the
environment.They are, however,
essential for the correct functioning of
your appliance. Please do not therefore
dispose of the appliance with your
household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your Chartered Agent
for advice.
Ensure that your old appliance presents
no danger to children while being
stored for disposal.
2
Energy saving tips
To avoid unnecessarily long drying
times and high consumption of energy:
– Make sure that your laundry is
thoroughly spun before drying.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
– Load according to the optimum
amount of laundry recommended for
the programme being used.
Underloading is uneconomical.
Overloading gives poorer quality of
drying and may cause unnecessary
creasing.
– Make sure that the room temperature
is not too high. If there are other heat
producing appliances in the room in
which the dryer is located, make sure
the room is well ventilated and switch
the other appliances off if possible.
– After every cycle, remove the fluff
from the surfaces of the fluff filters
(see "Cleaning and Care").
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Care symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Extra options/Delay start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Extra options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Gentle tumble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Buzzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Changing the programme sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Once a programme has started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
- Cancelling the programme and then selecting a different programme . . . . . 25
- Cancelling the programme and then removing the laundry. . . . . . . . . . . . . . 25
Changing Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adding or removing laundry after a programme has started . . . . . . . . . . . . . . . . 25
Time remaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Emptying the condensed water container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Adhering to cleaning intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
When to clean the surfaces of the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . 27
When to clean the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3
Contents
Surfaces of the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning without water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Refitting the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Removing the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cleaning the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Cleaning the fine filter cover panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cleaning the heat exchanger unit compartment . . . . . . . . . . . . . . . . . . . . . . . 31
Replacing the fine filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cleaning the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Check and fault messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
An unsatisfactory drying result . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Other problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the cooling fins (Grille at bottom right) . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
After Sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Future updates (PC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Transporting the dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Building under a continuous worktop/in a row of kitchen units . . . . . . . . . . . . 43
Levelling the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
External condensed water outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Arranging the drain hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
External drainage via a sink or gully . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Installation conditions requiring a non-return valve . . . . . . . . . . . . . . . . . . . . . 46
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4
Contents
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Electronic system lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Extending the range of the drying level for the "Cottons" programme. . . . . . . . . . 53
Extending the drying level for the "Minimum iron" programme . . . . . . . . . . . . . . . 54
Altering the Anti-crease function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Altering the volume of the buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Extending the drying level for the "Automatic plus" programme . . . . . . . . . . . . . . 57
Setting Standby . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Memory function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Adjusting the dryer's electronics for very soft water . . . . . . . . . . . . . . . . . . . . . . . 62
Extending the drying level range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5
Warning and Safety instructions
~ It is essential to read these instructions.
This tumble dryer conforms to current safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the tumble dryer,
please read these instructions carefully before using it for the first
time. They contain important information on its safety, installation,
use and maintenance.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
~ This tumble dryer is designed for domestic use and for use in
similar environments by guests in hotel or motel rooms, bed &
breakfasts and other typical living quarters. This does not include
common/shared facilities or commercial facilities within hotels,
motels or bed & breakfasts.
~ This tumble dryer must only be used to dry items which have
been washed in a water solution and which are marked on the
manufacturer's care label as being suitable for tumble drying. "Dry
cleaning kits" for freshening up garments in a tumble dryer are
increasingly available on the market. If using, do so at your own risk,
and follow the instructions provided on the packaging.
Any other usage is not supported by the manufacturer and could be
dangerous. Miele cannot be held liable for damage resulting from
incorrect or improper use or operation of the tumble dryer.
6
Warning and Safety instructions
~ The tumble dryer is not suitable for outdoor use.
~ This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience or knowledge, unless they are supervised whilst
using it or have been shown how to use it correctly by a person
responsible for their safety.
~ This tumble dryer must not be installed and operated in mobile
installations (e.g. on a ship).
Safety with children
~ Keep children away from the tumble dryer at all times. It is not a
toy! To avoid the risk of injury do not allow them to play on or near it
or to play with its controls. Supervise children whilst you are using it.
~ Older children may only use it if its operation has been clearly
explained to them, and they are able to use it safely, recognising the
dangers of incorrect use.
7
Warning and Safety instructions
Technical safety
~ Before setting up the tumble dryer, check it for any externally
visible damage.
Do not install or use a damaged tumble dryer.
~ Before connecting the appliance, make sure that the connection
data on the data plate (voltage and rated load) match the mains
electricity supply. If in doubt, consult a qualified electrician.
~ The electrical safety of this appliance can only be guaranteed
when continuity is complete between it and an effective earthing
system. It is most important that this basic safety requirement is
present and regularly tested and where there is any doubt, the
household wiring system should be inspected by a qualified
electrician. Miele cannot be held liable for the consequences of an
inadequate earthing system (e.g. electric shock).
~ The heat pump technology in the
tumble dryer uses a refrigerant which is condensed by a
compressor. It is led in a closed circuit through the heat exchanger
unit where heat exchange with the circulating drying air takes place.
It is normal for humming noises caused by the heat pump
technology to be heard during the drying process. This does not
impair the efficient functioning of the dryer.
– The refrigerant is not flammable or explosive.
– In general it is not necessary to leave the dryer standing for any
length of time before it is connected to the mains provided it has
been transported and installed correctly (see "Installation").
~ Do not connect the tumble dryer to the mains electricity supply by
an extension lead. Extension leads do not guarantee the required
safety of the appliance (e.g. danger of overheating).
8
Warning and Safety instructions
~ Unauthorised repairs could result in unforeseen dangers for the
user, for which Miele cannot accept liability. Repairs should only be
undertaken by a Miele approved service technician.
~ Faulty components must only be replaced by genuine Miele
spare parts. Only when these parts are fitted can the safety
standards of the tumble dryer be guaranteed.
~ If the connection cable is faulty, it must only be replaced by a
Miele approved service technician to protect the user from danger.
~ In the event of a fault or for cleaning purposes, the tumble dryer
is only completely isolated from the electricity supply when:
– it is switched off at the wall socket and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn.
~ Do not make any alterations to the tumble dryer, unless
authorised to do so by Miele.
~ In areas which may be subject to infestation by cockroaches or
other vermin, pay particular attention to keeping the appliance and
its surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the warranty.
9
Warning and Safety instructions
Correct use
, Caution! Risk of fire.
To avoid the possible danger of fire, please
read these warnings carefully.
, A clogged filter is a fire hazard!
The fluff filter must be cleaned after every programme.
~ Remove all objects from pockets such as lighters and matches.
~ To prevent the risk of fire, the following textiles must not be dried
in this tumble dryer:
– Items which have not been washed.
– Items, such as workwear, which have not been thoroughly
cleaned and which are still soiled with grease, oil or other
desposits (such as cosmetics, lotions etc).
If items have not been thoroughly cleaned, there is a danger that
these might ignite when heated, even after they have been
removed from the dryer at the end of the programme.
– Items that have been soiled with substances such as cooking oil,
acetone, petrol, kerosene, spot removers, turpentine, waxes, wax
removers and other chemicals (e.g. mops and floor cloths) should
be washed in hot water with extra detergent before being dried in
the tumble dryer.
– Items which have been splashed with hair lacquer, hair spray, nail
polish remover or similar substances.
10
Warning and Safety instructions
When washing such heavily soiled items, ensure that you use
sufficient detergent and select a high temperature. If in doubt,
wash the items several times.
~ Oil-affected items can ignite spontaneously, especially when
exposed to heat sources such as in a tumble dryer.
The items become warm, causing an oxidation reaction in the oil.
Oxidation creates heat.
If the heat cannot escape, the items can become hot enough to
catch fire. Piling, stacking or storing oil-affected items can prevent
heat from escaping and so create a fire hazard.
If it is unavoidable that fabrics contaminated with vegetable or
cooking oil, or hair care products, be placed in a tumble dryer, they
should first be washed in hot water with extra detergent - this will
reduce, but not eliminate, the hazard.
~ To prevent the risk of fire, the following textiles or products must
not be dried in this tumble dryer:
– Items which have been dry-cleaned (for example with a chemical
treatment).
– Fabrics which contain a large proportion of rubber, foam rubber or
rubber-like materials. For example, products made from latex
foam rubber, shower caps, waterproof textiles, rubberised articles
and items of clothing and pillows with foam rubber filling.
– Fabrics which contain padding or fillings (e.g. pillows, jackets). If
these were damaged, the filling could get out with the risk of
igniting in the dryer.
11
Warning and Safety instructions
~ In many programmes, the heating phase is followed by a cooling
down phase to ensure that the items are not too hot to handle when
you remove them (this also avoids the danger of the laundry
self-igniting). The programme is not finished until the cooling down
phase is complete.
Ensure that you always wait until the end of the programme before
removing the laundry.
~ Warning: Do not switch the tumble dryer off before the end of the
drying programme. If this was done, remove and spread out all
items quickly so that the heat is dissipated.
~ Risk of fire!
This tumble dryer must not be connected to a timer switch or safety
switch adapter.
If the drying programme is interrupted, there is the risk of laundry
catching fire.
~ Fabric conditioner and similar products must be used according
to the instructions on the manufacturer's packaging.
~ The tumble dryer is not to be used if industrial chemicals have
been used to clean it.
~ For appliances with ventilation openings in the base, a carpet
must not obstruct the openings.
12
Warning and Safety instructions
~ The tumble dryer must not be used
– without the fluff filters in place or if the fluff filters are damaged.
– without the fine filter in place or if the fine filters are damaged.
This would cause an excessive build-up of fluff which in turn would
cause a fault!
~ After every cycle, remove the fluff from the surfaces and the fluff
filters (see "Cleaning and care").
~ Fluff must not be allowed to accumulate around the tumble dryer.
~ The fluff filters and the fine filter must be thoroughly dried after
cleaning. Damp or wet filters could cause operational faults.
~ Do not install the tumble dryer in a room where there is a risk of
frost occurring. At temperatures around freezing point the tumble
dryer may not be able to operate properly.
There is a risk of damage if the condensed water is allowed to
freeze in the pump and in the drain hose.
~ If the water is drained externally through the drain hose instead of
being collected in the condensed water container, make sure the
drain hose is securely attached if you hang it in a sink or basin to
avoid the hose slipping and the water causing damage.
~ Condensed water is not drinking water. It can cause health
problems in both people and animals.
13
Warning and Safety instructions
~ Always keep the area around the tumble dryer free of dust and
fluff.
Dust drawn into the tumble dryer can cause blockages in the
condenser unit over time.
~ Do not lean on the door. This can cause the tumble dryer to tip
over.
~ Always close the door after use.
This way you will avoid the
danger of
– children climbing onto or into the dryer or hiding things in it.
– pets or other small animals climbing into it.
~ The tumble dryer must not be hosed down.
Accessories
~ Only use genuine Miele spare parts and accessories with this
tumble dryer. If non-Miele parts are used, warranty, performance
and product liability claims may be invalidated.
Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety instructions.
14
Operating the tumble dryer
Control panel
a Gentle tumble button
For drying items which are not
suitable for drying with a great deal
of mechanical action. When this
option is selected, the drum will
rotate less frequently.
b Drying level button
Indicator lights show the selected
drying level. See "How to dry
correctly".
c Display
See the next page.
d Delay start button
This button is used for:
- Delaying the start of a programme.
- Selecting Warm air duration.
e Buzzer button
An audible tone sounds at the end of
the programme.
f Perfect Dry indicator light
For all drying levels. See the next
page.
g Fault/Check lights
See "Problem solving guide" and
"After Sales service".
h Start/Stop button
For starting the programme selected
and cancelling a programme once it
has started.
The button flashes when a
programme is selected and then is
on constantly when the programme
has started.
i Programme selector
The programme selector can be
turned clockwise or anti-clockwise.
Indicator lights show the selected
programme.
j Door button
Pressing this button will open the
door even when the dryer is
switched off at the mains.
k jk button
For switching the tumble dryer on
and off.
15
Operating the tumble dryer
The following information appears in
the display:
– Programme duration
– Programme sequence
Drying
Cooling down
Finish
The Perfect Dry indicator light remains
dark during the following time
controlled programmes: Woollens,
Warm air, Gentle smoothing.
Estimated time remaining
– Programmable functions
The programmable functions are
used to alter the machine's
electronics to suit changing
requirements. See "Programmable
functions" later in this booklet for
more details.
The expected time will automatically be
displayed (Estimated time remaining).
The following factors all affect the
estimated time remaining: residual
moisture content after spinning; type of
fabric; size of load; room temperature
or fluctuations in the power supply.
The electronics continually assess
conditions in the tumble dryer and
adjust the estimated time remaining for
a more accurate reading. Because of
this, the time displayed can alter during
the course of a programme.
In the same way, programmes may
finish early. This can happen with
particularly fine fabrics, very small
loads or if items were partly dry
beforehand.
Perfect Dry indicator light
Before using for the first time
– Check and fault messages
The following can be set via the
display:
– Programme duration for Warm air
– Delay start
You can set a programme to start
automatically at a later time.
The Perfect Dry system measures the
laundry's residual moisture in
programmes with drying levels and
provides a more precise drying result.
After starting the programme, the
electronics will measure the duration of
the programme (Estimated time
remaining). The Perfect Dry indicator
light will flash during this time.
The programme duration will be shown
after a short time and the indicator light
will go out.
Once the selected drying level has
been reached, the Perfect Dry indicator
light will remain on until the end of the
programme.
16
,Install and connect the tumble
dryer according to the descriptions
in these operating instructions. If the
tumble dryer has not been
transported as described, then it
must be left to stand for at least 1
hour before it is connected to the
electricity supply.
Notes on laundry care
Care symbols
Drying
q/r Normal/lower temperature.
This dryer is able to dry at lower
temperatures in each
programme. It is not necessary
to divide fabrics q/r.
s
Do not tumble dry.
Ironing
I Very hot.
H Hot.
G Warm.
J Do not iron.
Tips on drying
– See the "Programme chart" for
maximum recommended loads for
each programme.
Overloading can cause unnecessary
wear and tear to the laundry, give a
disappointing drying result and
cause more creasing.
– Do not tumble dry loopknit garments!
Spin garments for at least 30
seconds after washing.
– Open jackets so that they can dry
evenly.
– Loopknit garments (e.g. T-shirts,
underwear) have a tendency to
shrink after the first wash. Therefore:
To avoid further shrinking, do not
overdry these fabrics. When buying
loopknit garments, it is advisable to
take their shrinkage properties into
account.
– Creasing in minimum iron fabrics
increases with the size of the load.
This applies in particular to very
sensitive fabrics (e.g. shirts,
blouses).
Choose a suitable programme for
these fabrics. If in doubt, reduce the
size of the load and select the Gentle
tumble Extra option.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– New dark coloured garments should
be washed separately from light
coloured garments. Do not dry these
together with light garments as they
may lose their colour (also onto
plastic components in the tumble
dryer). Dark coloured fibres can also
settle on light coloured garments and
vice versa.
– Use the Automatic plus programme
for drying mixed loads of cottons,
colours and minimum iron fabrics.
– Pure linen may become rough. Pure
linen should only be machine dried if
specified as suitable by the
manufacturer on the care label.
17
How to dry correctly
Brief instructions
The headings numbered (A, B, C ...)
show the operating sequence and can
be used as a brief guide to using your
machine.
A Sort the laundry
Separate the washed laundry and sort it
according to . . .
. . . the drying level required,
. . . the type of fibre or weave,
. . . size,
. . . the moisture content after spinning.
In this way an even drying result will be
achieved.
,Make sure that objects, e.g.
detergent dispensing balls, have
been removed from the laundry.
They could melt and cause damage
to the dryer or the laundry.
^ Switch on the dryer by pressing the
jk button.
C Load the tumble dryer
^ Press the Door button to open the
door.
^ Load the laundry loosely into the
drum.
Do not overload the drum. See the
"Programme chart" for
recommended loads for each
programme.
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
^ Before closing the door, make sure
the fluff filter is correctly positioned in
the door.
– Check seams and stitching to ensure
that padding and linings are intact.
– Remove all objects from pockets
such as lighters and matches.
– Fasten duvet covers and pillow
cases to prevent small items from
being rolled up inside them.
– Fasten zips, hooks and eyes etc.
– Tie fabric belts and apron strings.
– Sew in or remove underwiring from
bras.
B Switch on the tumble dryer
The tumble dryer may be switched on
after loading, saving energy as the light
will not come on.
18
Check the laundry is right inside the
drum so that it cannot get trapped or
damaged when the door is shut.
^ Shut the door either with a gentle
swing, or lean against it and push it
shut.
How to dry correctly
D Selecting a programme
Tip:
You can extend the range of drying
levels for some of the programmes (see
"Programmable functions").
Woollens, Gentle smoothing,
Proofing programmes
– These programmes cannot be
changed.
Selecting Warm air duration
^ Select the programme you want.
The relevant indicator light will come
on.
Indicator lights for drying levels or Extra
options and times may also be
displayed.
Programmes with drying levels
– Cottons, Minimum iron, Outerwear,
Express, Automatic plus, Hygiene,
Denim and Shirts
The indicator light for the Delay start
button will flash when this programme
is selected.
^ Press the Delay start button until the
required time appears in the display.
You can select a duration of 20 minutes
up to 2:00 hours in increments of 10
mintues.
E Selecting Extra options / Delay
start
^ By pressing the relevant button, you
can select:
Gentle tumble, Buzzer, Delay start
(see "Extra options/Delay start").
Anti-crease (see next page) is always
switched on.
However: Delay start is not possible in
combination with Warm air.
^ Press the relevant button repeatedly
until the indicator light comes on.
Four drying levels can be selected with
the Cottons and Express programmes.
The selection of the other programmes
is limited and Hygiene cannot be
changed at all.
19
How to dry correctly
F Starting the programme
The Start/Stop button light will flash
when a programme is being selected.
The flashing indicates that a
programme can be started.
^ Press the Start/Stop button.
The Start/Stop button will now light up
constantly.
Perfect Dry only flashes/illuminates
during programmes with drying levels.
It remains dark during time controlled
programmes (see "Operating the
tumble dryer").
Note: The duration shown in the display
is only an estimate and can change.
Before the end of a programme
The heating phase is followed by a
cooling down phase (Cooling down
lights up). The programme is not
finished until the cooling down phase
has been completed.
G Removing the laundry at the end of
the programme
0 and Finish will appear in the display
to indicate that the programme has
finished. The buzzer (if selected) will
sound at intervals.
After the programme has finished, the
drum will continue to rotate for 2 hours
at intervals if the garments are not immediately removed. This reduces
creasing.
There is no anti-crease with: Woollens.
The dryer has a standby mode. After a
programme has finished, the display
will switch off and the Start/Stop button
20
light will flash slowly. Also see
"Programmable functions".
^ Press the Door button.
^ Open the door.
^ Remove the laundry.
Check that all items have been
removed from the drum. If items are
left in the dryer, they could be
damaged by overdrying when the
dryer is next used.
If the dryer is switched on and the door
is opened, the drum lighting will come
on. It will go out a few minutes later to
save energy.
^ Switch off the dryer by pressing the
jk button.
^ Clean the fluff filters.
^ Close the door.
^ Empty the condensed water
container.
We recommend draining it externally.
This means you will never have to
empty it manually again.
Using the Cottons Extra Dry programme
is recommended for a mixed cotton load
and is the programme used in energy
consumption tests to AS/NZS 2442
(Refer to www.energyrating.gov.au
website for consumption data).
Extra options/Delay start
Extra options
To begin Delay start
The relevant indicator light will come on
when selected.
^ Press the Start/Stop button.
Gentle tumble
For drying items which are not suitable
for drying with a great deal of
mechanical action. When this option is
selected, the drum will rotate less
frequently.
The programme duration will be
extended.
If in doubt, reduce the size of the load.
Buzzer
A buzzer sounds (at intervals for a
maximum of 1 hr) to let you know the
programme has finished.
The buzzer will always sound when
there is a fault, even if it has been
switched off.
Delay start
The start of a programme can be
delayed from 30 minutes up to 24
hours.
^ Select a programme.
^ Press the Delay start button until the
required time appears in the display.
– The Delay start indicator light will
flash.
– The Delay start indicator light will
light up constantly.
– Delay start counts down in one hour
steps to i0^ and afterwards in minute
steps until the programme starts.
– The drum will turn briefly every hour
to help prevent creasing.
To cancel/alter Delay start
^ Press the Start/Stop button to cancel
Delay start.
^ Press the Delay start button until the
required time appears in the display.
^ Press the Start/Stop button to begin
Delay start.
Add laundry
You can add laundry while Delay start
is counting down:
^ Switch the dryer off.
Opening the door before switching off
the dryer first will cancel Delay start.
^ Open the door and add laundry.
^ Close the door and switch the dryer
on.
– The selection can be made in steps
of 30 minutes up to i0^ and
afterwards in one hour steps.
– If you keep the Delay start button
pressed in, the time will continue to
increase up to 24^.
21
Programme chart
Extra options
Gentle tumble
Able to be selected with the
following programmes:
Cottons, Minimum iron, Shirts, Denim, Warm air.
Buzzer
Able to be selected with all programmes.
Programmes
Cottons
Max. load: 8 kg*
Extra dry, Normal**
Fabric type Single and multi-layered cotton fabrics such as
towelling, jerseywear, T-shirts, underwear.
Notes
– Select Extra dry for multi-layered and very thick fabrics.
– Do not use Extra dry for loopknit fabrics (e.g. T-shirts,
underwear), as they have a tendency to shrink.
Hand iron**, Machine iron
Fabric type Cotton and linen fabrics. For example: table linen, bed linen,
starched laundry.
Note
To prevent laundry from drying out, it should be rolled up until you
are ready for ironing.
Minimum iron
Max. load: 3.5 kg*
Normal**, Hand iron
Fabric type Minimum iron items made of cotton, synthetic or mixed fibres. For
example: dresses, trousers, skirts or table cloths.
* Weight of dry laundry
Note for test institutes:
– ** Use this programme without selecting any Extra for testing according to
EN 61121 standard.
– When selecting the Cottons programme, drain off the condensed water
externally via the drain hose.
22
Programme chart
Woollens
Max. load: 2 kg*
Fabric type Fabrics containing wool blends.
Notes
– Woollen garments are fluffed up.
– Remove garments immediately at the end of the programme.
Outerwear
Max. load: 2.5 kg*
Normal, Hand iron
Fabric type Outerwear which is suitable for drying in a tumble dryer.
Proofing
Max. load: 2 kg*
Fabric type For drying microfibre fabrics, ski wear, fine, closeweave cotton
garments (poplin) or tablecloths which are suitable for drying in a
tumble dryer and have been treated to provide a water and dirt
resistant finish.
Notes
– This programme contains an extra fixing phase for proofing.
– Only use proofing agents which are stated by the manufacturer
as being "suitable for use on membrane textiles" as these
contain fluorochemical compounds.
– Do not dry items which have been treated with proofing agents
containing paraffin. Fire hazard!
Express
Max. load: 3.5 kg*
Extra dry, Normal, Hand iron, Machine iron
Fabric type Tougher fabrics for the Cottons programme.
Note
Reduced programme duration.
Automatic plus
Max. load: 5 kg*
Normal, Hand iron
Fabric type Mixed loads of garments suitable for the Cottons and Minimum iron
programmes. Sort according to colour.
Shirts
Max. load: 2 kg*
Normal, Hand iron
Fabric type Shirts and blouses.
Denim
Max. load: 3 kg*
Normal, Hand iron
Fabric type Denim garments, e.g. trousers, jackets, skirts or shirts.
* Weight of dry laundry
23
Programme chart
Hygiene
Max. load: 3.5 kg*
Fabric type
Cottons and linen fabrics, which will be in direct contact with the
skin, e.g. underwear, nappies, towelling, bed linen, pillow and
mattress covers.
Note
The temperature is held constant for a longer period of time to
deactivate micro-organisms, e.g. germs or house dustmites, and
also to reduce the number of allergens in the laundry.
This programme should not be interrupted as this would prevent
the micro-organisms from being deactivated.
Warm air
Max. load: 7 kg*
Fabric type
– "Voluminous" and multi-layered fabrics whose layers have
different drying characteristics: e.g. jackets, pillows.
– For drying individual items, e.g. bath towels, swimwear, tea
towels and small loads.
Note
Do not select the longest drying time to start with. Check the items
as you are drying them to find the optimum time.
Tip
You can use the Warm air programme to help remove odours from
cotton clothing which has been worn but is still clean (select a
duration of between 1/2 and 1 hour). Items must be suitable for
drying in a tumble dryer. Dampen the garments a little beforehand
or add a fabric conditioner sheet.
The Warm air programme will not be as effective at removing
odours from any parts of the garments which are made of synthetic
fibres.
Gentle smoothing
Fabric type
Max. load: 1 kg*
– Cotton and linen fabrics.
– Minimum iron items made of cotton, synthetic or mixed fibres.
For example: trousers, anoraks, shirts.
– Suitable for dry and damp laundry/fabrics.
Dry fabrics are time-controlled and damp fabrics are smoothed
using the Hand iron function.
– Smoothes out creasing caused during the spin cycle in the
washing machine.
– Remove garments as soon as the programme has finished so
that they are easy to iron.
* Weight of dry laundry
Notes
24
Changing the programme sequence
You cannot change to another
programme once a programme has
started (this prevents unintentional
alterations).
You will need to cancel the current
programme before you can select a
new one.
Once a programme has started
- Cancelling the programme and then
selecting a different programme
^ Press the Start/Stop button.
The items will be cooled down,
depending on the temperature
reached and how long they have
been dried for.
Changing Delay start
^ See "Delay start".
Adding or removing laundry
after a programme has started
^ Press the Door button.
^ Open the door.
^ Add or remove items as required.
^ Close the door.
^ Press the Start/Stop button.
Time remaining
Changes to the programme sequence
can alter the estimated time remaining
in the display.
If you press the Start/Stop button
again during the cooling down
phase, Finish will appear in the
display.
^ Switch off the tumble dryer by
pressing the jk button.
^ Switch on the tumble dryer by
pressing the jk button.
^ Select and start a new programme.
- Cancelling the programme and then
removing the laundry
^ Refer to the following: "Adding or
removing laundry after a programme
has started".
^ Switch the dryer off after closing the
door.
25
Cleaning and care
Emptying the condensed water
container
Condensate is collected in the
condensed water container during
drying.
Empty the condensed water
container after every drying
programme, unless the dryer has
been connected for external
drainage (see "Installation").
If the condensed water container is full,
– the programme will be cancelled.
– the Empty the container indicator
light comes on.
The indicator light will go out when the
door is opened and closed again.
^ Empty the condensed water
container.
^ Slide the container back into the
dryer.
,Condensed water should not be
consumed. It could lead to health
problems for people and animals.
Condensed water can be put to
household use (e.g. used in a steam
iron or humidifier). To ensure that any
residual particles of fluff in the
condensed water are removed before
use, pass it through a fine sieve or
paper filter first.
^ Pull out the condensed water
container.
^ Hold it at the front and towards the
back and keep it in a horizontal
position when carrying it.
26
Cleaning and care
Adhering to cleaning intervals
This tumble dryer has a multistage
filter system, consisting of the fluff
filters in the door and the door
opening and an additional fine filter.
This system requires maintenance.
– This tumble dryer must not be
used without the fluff filters and
fine filter in place.
The grille at the bottom right of the
appliance must also always be in
place.
– Also ensure that the fluff filters
and the fine filter are not damaged.
If they are damaged: replace them
immediately (optional
accessories).
,Failure to follow instructions:
The tumble dryer may experience an
excessive build-up of fluff, which in
turn could cause a fault.
^ See "Surfaces of the fluff filters".
When to clean the fine filter
Only clean the fine filter if the Clean
the filters indicator light comes on.
The fine filter is located behind the
cover panel at the bottom left of the
appliance.
It collects finer fluff, hair and
detergent residues which have got
through the surfaces of the fluff filters
in the door and the door opening.
^ See section "Fine filter".
When to clean the surfaces of the
fluff filters
Clean fluff filters after every
programme.
The fluff which is created by the
drying process is collected by the
fluff filters in the door and the door
opening.
27
Cleaning and care
Surfaces of the fluff filters
Cleaning intervals
Clean the surfaces of the fluff filters
in the door and the door opening
after each drying programme.
Cleaning without water
Tip: You can use a vacuum cleaner to
remove the fluff.
^ Use your fingers or a vacuum cleaner
to remove the fluff from the surface of
the filter.
1 Fluff filter
2 Seal
^ Open the door and pull the fluff filter
(1) out of the door as illustrated.
^ Remove any fluff from the hollow part
of the door with a bottle brush or a
vacuum cleaner.
^ Use your fingers or a vacuum cleaner
to remove the fluff from the two fluff
filters in the door opening.
^ Also clean the door seal (2) with a
damp cloth.
^ Push the filter back into the door
holder until it clicks into position.
Ensure it is facing the correct way.
^ Close the door.
28
Cleaning and care
Cleaning with water
If there is a great deal of compacted
fluff on any of the filters, they must
be removed and cleaned under hot
running water.
^ Open the door and pull the fluff filter
out of the door as described
previously.
The two filters in the door opening can
also be removed if you need to clean
them with water.
Refitting the filters
,The fluff filters must be dry
before they are refitted. Damp or wet
filters could cause operational faults.
^ Push the filter back into the door
holder until it clicks into position.
Ensure it is facing the correct way.
^ Replace the filters in the door
opening by first inserting them at the
bottom and then pressing them into
place at the top.
^ Lock both dials (you will feel them
click into position).
^ Turn the dial a on each fluff filter
until you feel it click.
^ Pull the filter out of the door opening
by the dial as shown b.
^ Rinse all the filters under hot, running
water.
^ Carefully dry the fluff filters
thoroughly.
^ Clean the area underneath these
filters, e.g. with a vacuum cleaner.
29
Cleaning and care
Fine filter
Cleaning intervals
Only clean the fine filter if the Clean
the filters indicator light comes on.
To switch off the Clean the filters
indicator light:
^ Remove, clean and refit the fine filter
while the dryer is switched on.
^ Pull the fine filter out by the handle.
Removing the fine filter
At the bottom left of the appliance:
^ Pull the handle out of the fine filter.
^ Press the cover panel for the fine
filter.
The panel will open.
Cleaning the fine filter
^ Clean the fine filter thoroughly under
running water.
^ Then squeeze the fine filter
thoroughly.
,The fine filter must not be
replaced in the dryer dripping wet.
This could cause a fault to occur.
^ Remove any fluff on the handle with a
damp cloth.
30
Cleaning and care
Cleaning the fine filter cover panel
Cleaning the heat exchanger unit
compartment
,Danger of injury!
Do not touch the cooling fins as they
are very sharp and may cut your
fingers.
,Risk of damage!
^ Remove any fluff with a damp cloth
(e.g. Original Miele all purpose
microfibre cloth, available at
www.miele-shop.com, depending on
country).
Be careful not to damage the rubber
seal.
Carefully run the dusting brush of
the vacuum cleaner across the
cooling fins.
Otherwise the cooling fins or the
braces in front of them may be
damaged.
In case of visible soiling:
^ Check whether the cooling fins are
dirty (refer to the following).
^ Carefully vacuum up any soiling
using a dusting brush or crevice
nozzle.
31
Cleaning and care
Replacing the fine filter
Only when the filter is fitted correctly
and the cover panel is closed can
the condensed water system be
sealed and the correct functioning of
the tumble dryer be guaranteed.
Cleaning the tumble dryer
Disconnect the machine from the
mains electricity supply.
^ Insert the handle into the fine filter.
In order that the filter sits correctly in
front of the heat exchanger unit:
^ Clean the housing, control panel and
door seal with a slightly damp cloth
and a mild detergent or soapy water.
^ The drum and other stainless steel
parts can be cleaned with a suitable
propietary stainless steel cleaner
following the manufacturer's
instructions.
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic surfaces and other
parts.
^ Dry all parts with a soft cloth.
^ Stick the handle with the filter
attached onto the two guide pins.
Ensure that the yellow dot is on the
right-hand side of the handle.
^ Push the handle in as far as it will go.
^ Close the cover panel.
32
Problem solving guide
Problem solving guide
With the help of the following notes, minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting Miele. A call-out charge will be applied to unnecessary service
visits where the problem could have been rectified as described in these
Operating instructions. Please note:
,Repair work to electrical appliances must only be carried out by a suitably
qualified and competent person in strict accordance with current local and
national safety regulations. Repairs and other work by unqualified persons
could be dangerous. The manufacturer cannot be held liable for unauthorised
work.
Check and fault messages
Problem
0-§ lights up and the
Gentle tumble indicator
light is flashing.
Possible cause
The system lock is
activated.
0 and Finish light up
and the programme is
cancelled.
The buzzer sounds. *
This is not a fault.
In some programmes, if
the drum has been
underloaded or there is
no laundry in the drum,
the programme will be
cancelled. This can also
happen if the items are
already dry.
Remedy
If you wish to use the
tumble dryer, the system
lock needs to be
deactivated (see
"Electronic system lock").
Use the Warm air
programme to dry
individual items.
– Empty the condensed
The Empty the container The condensed water
water container.
indicator light comes on container is full or there is
and the programme has a kink in the drain hose.
– Check the drain hose.
been cancelled.
The buzzer sounds. *
* Switch off the indicator light: Open and close the door (while the tumble
dryer is switched on).
33
Problem solving guide
Problem
Possible cause
Remedy
This is a reminder to
– Clean the fine filter.
clean the fine filter in front – See chapter "Cleaning and
of the heat exchanger unit
care".
under running water.
– The indicator light goes out
once the fine filter has been
removed and refitted while
the dryer is switched on.
The fine filter is not in
~F~ lights up and a
– Correctly fit the fine filter:
~F~ will go out.
programme cannot place or has been
be started.
incorrectly fitted.
– See chapter "Cleaning and
care".
The programme will be
– Fit the fine filter.
cancelled if the fine filter – Switch the dryer off and
is removed while the
then on again.
machine is in operation:
Cooling down is flashing.
The following
The programme has
You can remove the laundry
flashes at the end of finished but the laundry is and spread it out to allow the
still cooling down.
heat to dissipate, or leave it in
a programme:
the dryer to cool down more.
—œ–...C~–...Cœ˜....
– Switch the dryer off and
The programme is
There is no immediate
cancelled.
cause.
then on again.
– Start a programme.
The buzzer may
sound and Cooling
If the programme stops again
down or Finish is
and Cooling down or Finish
flashing.
flashes again, there is a fault.
Contact Miele.
The indicator light
The dryer is in standby.
See "Setting standby" in
Start/Stop flashes
This is a normal function "Programmable functions".
slowly and the
and does not indicate a
display is dark.
fault.
The Start/Stop
The flashing indicates
After the programme has
indicator light
that a programme can be started, the flashing will
flashes / lights up.
started.
change to a constant light.
The Clean the filters
indicator light
comes on at the end
of the programme.
34
Problem solving guide
An unsatisfactory drying result
Problem
Possible cause
Remedy
The laundry is not
sufficiently dry.
The load consisted of
different fabrics.
– Final drying cycle with
Warm air.
– Select a different
programme next time.
Tip: You can alter the drying See "Programmable
functions".
levels for some
programmes.
Garments or
downfilled pillows
develop an
unpleasant odour
due to tumble
drying.
– Not enough laundry
detergent was used
during washing.
– Feathers have the
tendency to develop a
characteristic odour
when exposed to heat.
– Garments: Use sufficient
laundry detergent.
– Pillows: Air pillows
outside the tumble dryer.
Items made of
synthetic fibres are
charged with static
electricity after
drying.
Synthetic fibres tend to
attract a static charge.
Static charge can be
reduced by adding a fabric
softener to the final rinse in
the washing programme or
a fabric conditioner sheet to
the load when drying.
There is a build-up of Fluff is principally the result
fluff.
of friction when garments
are being worn and to some
extent when they are being
washed. While fluff
detaches itself during
drying, very little of it forms
in the tumble dryer.
Fluff is collected by the fluff
filters and can be easily
removed (see "Cleaning
and Care").
35
Problem solving guide
Other problems
Problem
The drying
process goes
on too long or
even switches
off.
Possible cause
Remedy *
Ventilation to and from the
dryer may be insufficient
(e.g. because it is installed
in a small room). This has
caused the temperature in
the room to rise sharply.
Open a door or window while the
machine is in operation for
increased air flow.
– Detergent residue, hair
and fine fluff may have
blocked the fluff filters
and fine filter.
– The cooling fins may be
blocked.
– Clean the fluff filters and fine
filter.
– Remove any fluff:
. . . from the heat exchanger
unit at the bottom left (see
"Cleaning and care").
. . . from the cooling fins behind
the grille at the bottom right.
The cool air intake panel
(grille at bottom right) is
covered.
Remove the laundry basket or
other objects.
The fluff filters and the fine
filter were still wet when
they were replaced.
The laundry has not been
spun sufficiently.
The fluff filters and fine filter must
be dry before being replaced.
Make sure that your laundry is
thoroughly spun at the
appropriate spin speed in the
washing machine.
The tumble dryer has been Do not exceed the maximum load
overloaded.
for the programme selected.
– Open the zippers next time.
Metallic components, e.g.
zippers have prevented the – If the problem occurs again,
dryer from registering the
dry garments with long zippers
correct moisture level.
using the Warm air programme
(timed drying).
* Before starting a programme, switch the dryer off and then on again.
36
Problem solving guide
Problem
Possible cause
There are humming
noises.
The compressor is
operating.
A programme cannot
be started.
Power cut.
The interior drum
lighting is not
switched on.
Remedy
None. These noises are
quite normal and do not
indicate a fault.
There is no immediate
– Is the tumble dryer
cause.
switched on?
– Is the mains plug
plugged in?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
– If you cannot remedy the
problem, there is a fault.
Call Miele.
When power is restored to the tumble dryer after a
power cut, the programme will continue automatically.
The lighting switches off – Switch the dryer off and
automatically (to save
then on again.
energy).
– If the lamp needs to be
replaced, follow the
instructions under
"Changing the lamp" at
the end of this section.
37
Problem solving guide
Cleaning the cooling fins
(Grille at bottom right)
,Generally, the cooling fins do not
need to be cleaned. They should
only be cleaned if excessive
quantities of dust and lint are
causing unusually long drying times.
,To avoid damaging the cooling
fins, run the vacuum cleaner (using
dusting brush or crevice nozzle)
lightly across them without pressure.
Use the yellow opener supplied to open
the grille at the bottom right of the front
of the tumble dryer.
^ Carefully vacuum up any dust or lint
on the cooling fins which may be
causing a blockage.
^ Insert the opener in the top-centre of
the grille and carefully lift the opener
to pry open (see arrow) the grille.
^ Now remove the grille by pulling it
diagonally upwards.
^ Check whether the cooling fins are
blocked.
,Danger of injury!
Do not touch the cooling fins as they
are very sharp and may cut your
fingers.
38
^ Replace the grille by inserting at the
bottom first.
^ Then click it into position at the top.
Problem solving guide
Changing the lamp
Disconnect the machine from the
mains electricity supply.
The lamp specification and
maximum wattage are stated on the
data plate and on the lamp cover.
^ Open the door.
^ Replace the lamp.
You will find the interior lamp cover at
the top of the drum aperture.
^ To close the cover, push it upwards
and press it on the left and right until
you hear it click into position.
,Ensure that it is fitted into
position securely, as any moisture
could cause a short circuit.
^ Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the lamp cover as illustrated.
^ Apply a little pressure and, whilst
doing so, turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele
Chartered Agent or from Miele.
39
After Sales service
In the event of any faults which you
cannot remedy yourself, please contact
– Miele (see back cover for address).
When contacting Miele, please quote
the model and serial numbers, both of
which are located on the data plate
situated on the right-hand side below
the drum aperture.
Future updates (PC)
The indicator or check light marked PC
on the control panel is the interface
used by the Miele service technicians
during service work for testing
purposes and for updating the
machine's programme data.
Optional accessories
Optional accessories for these dryers
are available from your Miele Chartered
Agent or from Miele.
Please note that telephone calls may
be monitored and recorded to
improve our service.
40
Installation and connection
Front view
a Mains connection cable
f Four height adjustable screw feet
b Control panel
g Cool air intake panel (do not block,
e.g. with wash basket)
c Condensed water container (empty
after every drying programme)
d Door
h Hose for external drainage of
condensed water (see "External
condensed water outlet")
e Fine filter cover panel (do not open
during drying programme)
41
Installation and connection
Rear view
,If transporting the dryer at an
angle, only tip towards the left side.
a Protruding lid for holding when
moving the machine (see arrows)
b Mains connection cable
c Hose for external drainage of
condensed water
d Accessories for connection to a sink
drain outlet
Transporting the dryer
When moving the dryer, hold it by the
lid where it protrudes to the rear. To
manoeuvre the machine out of its
packing case to its installation site, hold
it by the front feet as well as by the
edge of the lid where it protrudes to the
rear of the washing machine.
,Only transport the dryer as
shown in the following illustrations.
42
,If the tumble dryer has not been
transported as described, then it
must be left to stand for at least 1
hour before it is connected to the
electricity supply. Otherwise the
heat pump can be damaged.
Installation and connection
Installation site
,The appliance must not be
installed behind a lockable door, a
sliding door or a door with a hinge
on the opposite side to that of the
tumble dryer, in such a way that a
full opening of the tumble dryer door
is restricted.
,The cool air intake panel at the
front of the dryer must not be
blocked or covered, e.g. by a
laundry basket, as this would cause
a fault.
Building under a continuous
worktop/in a row of kitchen units
,It is very important to avoid a
build-up of heat.
The warm air which is expelled from
the rear of the dryer must be able to
dissipate.
Warm air which cannot dissipate
could cause a fault.
A build-up of heat can be avoided by:
– Adjusting the screw feet so that there
is a gap of at least 20 mm between the
floor and the bottom of the dryer.
– Creating a gap for the dryer in the
kitchen furniture plinth facing.
,The dryer should not be installed
next to a refrigeration appliance. The
warm air expelled from the rear of
the dryer would increase the
temperature around the refrigeration
appliance's heat exchanger causing
the compressor to run continuously.
If it is not possible to install the dryer
anywhere else, then the refrigeration
appliance must be sealed off from
the dryer.
,A building-under kit (Miele
accessory, available to order) with a
coverplate to replace the appliance's
lid is required if building under a
worktop. It must be fitted by a suitably
qualified person to ensure electrical
safety. The coverplate included in the
building-under kit replaces the
appliance's lid. It is necessary to fit the
coverplate for electrical safety
reasons.
– Fitting instructions are supplied with
the conversion kit.
– N.B. When built under, drying times
may be longer.
– The electrical socket must be
located in an accessible position
near the machine.
– Creating ventilation gaps in the
kitchen unit.
N.B. When built under, drying times
may be longer.
43
Installation and connection
With niche heights of:
– 830-840 mm, longer screw feet* are
required.
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
– 870-885 mm / 915-930 mm, one or
two raising kits* are required.
,The gap between the tumble
* accessory available to order
N.B. If you wish to push the tumble
dryer under a worktop and there is
space to do this without removing the
lid, the building-under kit is not
necessary. Otherwise the
building-under kit is essential.
Levelling the machine
dryer and the floor must not be
minimized by a plinth facing,
high-piled carpets etc., as this
would prevent sufficient ventilation.
Before moving the tumble dryer
again (e.g. when moving houses)
After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the tumble dryer is tipped up
when it is being moved. It is a good
idea to run the Cool air programme for
approximately 1 minute before moving
it. Any remaining condensed water will
then be fed into the condensed water
container or out through the drain hose.
Washer-dryer stack
The machine must be perfectly level to
ensure safe and proper operation.
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. The
appropriate "WTV" stacking kit* to
match your dryer is required.
* accessory available to order
,Stacking kits must only be
installed by a suitably qualified fitter.
44
Installation and connection
External condensed water
outlet
General notes
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose at
the back of the dryer. The condensed
water can also be drained off directly if
the machine is installed near a sink, drain
outlet etc. so that the condensed water
container does not have to be emptied.
Drain hose length . . . . . . . . . . . . 1.50 m
Maximum delivery head . . . . . . . 1.50 m
Maximum drain hose length . . . . 4.00 m
,If the on-site water drainage
system is not fitted with a non-return
valve or an appropriate air gap, one
must be fitted to prevent the risk of
back-flow (See "Installation conditions
requiring a non-return valve").
^ Pull the hose off its connection (see
arrow).
^ Allow any residual water to run into
the container.
^ Unwind the hose and pull it carefully
out of the holders.
The following optional accessories are
available:
– an extension hose
– a non-return valve kit for connection
to an external condensed water
outlet (includes an extension hose).
Maximum delivery head with
non-return valve fitted: 1.00 m
Arranging the drain hose
,Do not pull on the drain hose and
do not stretch it or allow it to become
kinked as it could get damaged.
^ Position the hose to the right or
left-hand side as necessary.
Leave the hose in the middle holder to
prevent it from becoming kinked
inadvertently.
^ There will be a small amount of
residual water in the drain hose.
Have a container ready to collect this.
45
Installation and connection
External drainage via a sink or gully
^ See "Front view" illustration.
,If you want to drain the water off
into a sink, you will need to secure
the hose carefully, e.g. by tying it to
a tap to make sure it cannot slip
during use. Otherwise there is a risk
of overflowing water which could
cause damage.
Example: Connection to a sink drain
outlet
The drain hose with non-return valve
fitted can be connected directly to a
suitable sink drain outlet.
^ Use the bow-shaped guide to
prevent the drain hose from
becoming kinked.
Installation conditions requiring a
non-return valve
,Certain installation conditions
require the fitting of a non-return
valve (available as an optional
accessory). A non-return valve will
prevent the risk of back-flow out of
the dryer which could cause
damage.
A non-return valve is required:
– If the tumble dryer is connected to a
sink drain outlet (see the following
section).
– If the tumble dryer is connected to a
drainage system already in use by
another appliance, e.g. a dishwasher
or washing machine.
46
^ Remove the following from the back
of the dryer at the top:
Adapter 1 and hose clip 3 behind it.
Installation and connection
^ Fit adapter 1 to the sink drain outlet
using nut 2.
If this nut has a flat disc in it, you
should take the disc out first.
^ Attach the end of the hose 4 to
adapter 1.
^ Use a screwdriver to tighten hose
clip 3 up close to the nut.
1 Adapter
2 Nut
3 Hose clip
4 End of the hose
5 Non-return valve
6 Tumble dryer drain hose
,Non-return valve 5 has to be
fitted with the arrow pointing in the
direction of flow (i.e. towards the
sink). Otherwise water will not drain
out of the machine.
^ Fit non-return valve 5 to the tumble
dryer drain hose 6, making sure it is
fitted in the correct direction (see
arrow on non-return valve).
^ Secure the non-return valve using
hose clips.
47
Installation and connection
Electrical connection
Important
This tumble dryer is supplied ready for
connection to an AC single phase
supply. The machine is supplied with a
mains cable with moulded plug.
The wires in the mains lead are
coloured in accordance with the
following code:
The accesibility of the plug must be
always ensured in order to separate the
dryer from the mains.
The appliance should be connected up
only by a qualified electrician, in
accordance with national and local
safety regulations.
For extra safety, it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
The voltage, rated load and plug rating
are given on the data plate. Please
ensure that these match the household
mains supply.
If the mains connection cable is
damaged, it must be replaced by the
manufacturer, its service agent or
similarly qualified persons in order to
avoid a hazard.
Green/yellow = earth
Blue = neutral
Brown = live
As the colours of the wires in the mains
lead of this appliance may not
correspond with the coloured markings
identifying the terminals in your plug,
proceed as follows:
The wire which is coloured green and
yellow must be connected to the
terminal in the plug which is marked
with the letter E or by the earth symbol
z or coloured green or green and
yellow.
The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.
The wire which is coloured brown must
be connected to the terminal which is
marked with the letter A or coloured
red.
WARNING
THIS APPLIANCE MUST BE
EARTHED
48
Consumption data
Load1
Final spin speed in Residual
a domestic washing moisture
machine
Energy Duration
kg
rpm
%
kWh
min.
Cottons Normal2
8.0
1000
60
2.10
137
Cottons Normal
8.0
8.0
8.0
8.0
1200
1400
1600
1800
53
50
44
43
1.90
1.80
1.60
1.55
124
118
105
103
Cottons Normal
+ Gentle tumble
8.0
1000
60
2.15
140
Cottons Hand ironrr2
8.0
1000
60
1.55
99
Cottons Hand ironrr
8.0
8.0
8.0
8.0
1200
1400
1600
1800
53
50
44
43
1.35
1.25
1.10
1.05
87
81
69
67
Minimum iron Normal2
3.5
1200
40
0.60
47
Minimum iron Normal
+ Gentle tumble
3.5
1200
40
0.65
49
Minimum iron Hand iron
3.5
1200
40
0.50
41
Automatic plus Normal
5.0
800
50
1.50
99
Shirts Normal
+ Gentle tumble
2.0
2.0
600
600
60
60
0.70
0.75
53
59
Gentle smoothing
1.0
1000
60
0.35
30
Proofing Normal
2.0
800
50
1.25
85
Denim Normal
+ Gentle tumble
3.0
3.0
900
900
60
60
1.40
1.45
94
99
Express Normal
3.5
1000
60
1.10
75
Woollens
2.0
1000
50
0.20
20
Cottons hygiene Normal
3.5
1000
60
1.90
126
1
2
Weight of dry laundry
EN 61121:2005 test programme
All data was calculated using EN 61121:2005 unless otherwise stated.
Note for test institutes:
– When selecting the Cottons programme, drain off the condensed water externally via the drain
hose.
– Before testing in accordance with EN 61121, dry a
3 kg load of cotton laundry with 70% residual moisture as per the above standard using the Cottons
Normal programme without any Extra options.
Consumption data can vary from the nominal values given above depending on the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity
supply and any Extra options selected.
49
Technical data
Height
850 mm
Width
595 mm
Depth
Depth with door open
596 mm
1071 mm
Height for building under
Width for building under
820 mm
600 mm
Depth for building under
Suitable for pushing under a
worktop
600 mm
Yes
Suitable for stacking
Weight
Yes
61 kg
Drum volume
Maximum capacity
111 l
1-8 kg dry weight
Capacity of condensed water
container
Drain hose length
approx. 4.2 l
Maximum delivery head
Maximum drain hose length
1.5 m
4m
Length of connection cable
2m
1.5 m
Voltage
Rated load
Fuse rating
See data plate
Lamp wattage
Test certificates awarded
Energy consumption
50
See "Consumption data"
Electronic system lock
and
Programmable functions for changing
standard settings
This tumble dryer is programmed at
the factory so that is operates
effectively for all requirements.
However, you do have the ability to
change the standard settings.
You can adapt the electronics of the
tumble dryer to suit your personal
needs.
The features "Electronic system lock"
and "Programmable functions" are at
your disposal, but do not have to be
utilised.
51
Electronic system lock
The system lock prevents your
machine being used without your
knowledge.
You can switch on the system lock if
required.
The dryer's electronics are then locked.
The dryer can still be switched on but a
programme cannot be started.
– If an attempt is made to start a
programme, the indicator light for the
Gentle tumble button will come on
and the key symbol 0-§ will appear
in the display.
D Now slowly turn the programme
selector six positions stage by stage
in an anti-clockwise direction.
Each of the six programme indicator
lights must come on one after the
other.
The indicator light for the Gentle tumble
button will flash and a key symbol 0-§
will appear in the display.
E Release the Gentle tumble button.
The system lock is activated.
^ Switch the dryer off.
Deactivating the system lock
The door is not locked and can be
opened at any time.
Before you begin, first ensure that:
Locking
– The door is closed.
Before you begin, first ensure that:
^ The procedure is the same as for
activating the lock. Repeat steps A
to E.
– The dryer is switched off.
– The door is closed.
– The dryer is switched off.
A Press the Gentle tumble button and
keep it pressed in up to step E.
At step E the indicator light for the
Gentle tumble button will stop flashing
and the key symbol 0-§ will go out.
B Press the jk button.
The electronics are no longer locked.
The Automatic plus indicator light will
come on.
C Slowly turn the programme selector
three positions stage by stage in a
clockwise direction.
Each of the three programme
indicator lights must come on one
after the other.
52
Programmable functions
Extending the range of the
drying level for the "Cottons"
programme
The electronics of this dryer ensure a
very effective and energy-efficient
drying process.
You can, however, extend the range
of the drying level in this programme
so that there is more or less moisture
in the laundry at the end of the
programme.
Follow steps (A,B,C ...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
The option selected will be displayed
by a number which will alternate with
P.
0 The drying level will be damper
I Factory default setting
(the Automatic plus indicator light will
also flash once)
2 The drying level will be drier
(the Automatic plus indicator light will
also flash twice)
D Pressing the Start/Stop button
switches from one number to the
other.
E Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
B Switch the dryer on.
^ Repeat steps A to C.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
^ Switch the dryer off after step C.
C . . . and then release the Start/Stop
button.
– The Gentle tumble indicator light will
briefly flash once.
53
Programmable functions
Extending the drying level for
the "Minimum iron"
programme
The electronics of this dryer ensure a
very effective and energy-efficient
drying process.
You can, however, extend the range
of the drying level in this programme
so that there is more or less moisture
in the laundry at the end of the
programme.
Follow steps (A,B,C ...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
The option selected will be displayed
by a number which will alternate with
P.
0 The drying level will be damper
I Factory default setting
(the Automatic plus indicator light will
also flash once)
2 The drying level will be drier
(the Automatic plus indicator light will
also flash twice)
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
B Switch the dryer on.
^ Repeat steps A to D.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
^ Switch the dryer off after step D.
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button once.
– The Gentle tumble indicator light will
briefly flash twice.
54
Programmable functions
Altering the Anti-crease
function
Helps prevent creasing if laundry is
not normally removed immediately
after the end of a programme.
Anti-crease
– is set at the factory, can be
shortened or switched off
completely.
– can be used for all programmes,
except Woollens.
– should always be switched on.
Follow steps (A,B,C ...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
The option selected will be displayed
by a number which will alternate with
P.
0 Anti-crease deactivated
I 1 hour Anti-crease
(the Automatic plus indicator light will
also flash once)
2 Factory default setting; 2 hours
Anti-crease
(the Automatic plus indicator light will
also flash twice)
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
^ Repeat steps A to D.
^ Switch the dryer off after step D.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button
twice.
– The Gentle tumble indicator light will
briefly flash three times.
55
Programmable functions
Altering the volume of the
buzzer
The buzzer has two volumes.
The option selected will be displayed
by a number which will alternate with
P.
Follow steps (A,B,C ...) to
programme and store in memory.
0 Factory default setting; Normal
buzzer
Before you begin, first ensure that:
I Loud buzzer
(The Automatic plus indicator light
will also flash)
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
C . . . and then release the Start/Stop
button.
Check
D Press the Gentle tumble button three
times.
^ Switch the dryer off after step D.
– The Gentle tumble indicator light will
briefly flash four times.
56
^ Repeat steps A to D.
Programmable functions
Extending the drying level for
the "Automatic plus"
programme
The electronics of this dryer ensure a
very effective and energy-efficient
drying process.
You can, however, extend the range
of the drying level in this programme
so that there is more or less moisture
in the laundry at the end of the
programme.
Follow steps (A,B,C ...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
The option selected will be displayed
by a number which will alternate with
P.
0 The drying level will be damper
I Factory default setting
(the Automatic plus indicator light will
also flash once)
2 The drying level will be drier
(the Automatic plus indicator light will
also flash twice)
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
B Switch the dryer on.
^ Repeat steps A to D.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
^ Switch the dryer off after step D.
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button four
times.
– The Gentle tumble indicator light will
briefly flash six times.
57
Programmable functions
Setting Standby
To save energy, the display goes out
after 10 minutes and the indicator
light for the Start/Stop button will start
flashing slowly.
Factory default; Not in current
programme
As described under "On".
But: The display and indicator lights will
not switch off during a programme.
Reactivating from Standby
Off
^ Turning the programme selector or
pressing one of the buttons switches
the display back on again. This will
not alter a running programme.
The display and indicator lights will not
switch off when the dryer is switched
on.
On
Follow steps (A,B,C ...) to
programme and store in memory.
Standby is activated:
– if a programme is not selected after
the machine has been switched on.
– after a programme has started.
However: The display will switch on for
10 minutes if Delay start has finished,
after the end of a progamme or the
Anti-crease cycle.
The buzzer (if selected) will sound for
10 minutes after the end of a
progamme.
58
^ See the next page.
Programmable functions
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button five
times.
– The Gentle tumble indicator light will
briefly flash eight times.
The option selected will be displayed
by a number which will alternate with
P.
0 On
I Factory default setting; Not in
current programme
(Indicator light Automatic plus will
also flash once)
2 Off
(the Automatic plus indicator light will
also flash twice)
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
^ Repeat steps A to D.
^ Switch the dryer off after step D.
59
Programmable functions
Memory function
The electronics will memorise any
Extra options selected for a
programme. The duration selected
for the timed drying programmes will
also be stored in memory.
These settings will be selected
automatically the next time the
programme is chosen. You can either
accept these or change them by
pressing the appropriate button.
Follow steps (A,B,C ...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button six
times.
– The Gentle tumble indicator light will
briefly flash nine times.
60
The option selected will be displayed
by a number which will alternate with
P.
0 Factory default setting; Memory
deactivated
I Memory
(The Automatic plus indicator light
will also flash)
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
^ Repeat steps A to D.
^ Switch the dryer off after step D.
Programmable functions
Keypad tone
An audible tone sounds each time a
button is pressed.
The option selected will be displayed
by a number which will alternate with
P.
Follow steps (A,B,C ...) to
programme and store in memory.
0 Factory default setting; Keypad
tone deactivated
Before you begin, first ensure that:
I Keypad tone activated
(The Automatic plus indicator light
will also flash)
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button
seven times.
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
^ Repeat steps A to D.
^ Switch the dryer off after step D.
– The Gentle tumble indicator light will
flash slowly once and will then flash
quickly once.
61
Programmable functions
Adjusting the dryer's
electronics for very soft water
,Extremely soft water can affect
the sensitivity of the control
electronics.
Important
If the dryer is installed in an area with
very soft water, you should contact your
local water supplier for information and
advice regarding water hardness and
water conductivity.
If the water conductivity is less than 150
µS, the following programmable
function will need to be activated.
This programmable function should
not be activated if, despite the water
being extremely soft (as would be
the case if a water softener were
used), its conductivity is greater
than 150 µS.
Otherwise, the drying result will not
be satisfactory.
Follow steps (A,B,C ...) to
programme and store in memory.
Before you begin, first ensure that:
– The dryer is switched off.
– The door is closed.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
Wait until the indicator light for the
Start/Stop button lights up constantly. .
.
62
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button eight
times.
– The Gentle tumble indicator light will
flash slowly once and will then flash
quickly twice.
The option selected will be displayed
by a number which will alternate with
P.
0 Factory default setting
I Adjusted for very soft water (with
low conductivity)
(The Automatic plus indicator light
will also flash)
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Check
^ Repeat steps A to D.
^ Switch the dryer off after step D.
Programmable functions
Extending the drying level
range
You can extend the range of the
drying levels for many of the
programmes:
Machine iron +
(drier than Machine iron).
Light dry
(dryer than Hand iron).
Normal+
(dryer than Normal).
You can use this programming function
only for programmes which allow you to
select the drying levels.
Follow steps (A,B,C ...) to
programme and store in memory.
The option selected will be displayed
by a number which will alternate with
P.
0 Factory default setting
i Drying level range extended
(The Automatic plus indicator light
will also flash)
E Pressing the Start/Stop button
switches from one number to the
other.
F Switch the dryer off.
The setting you have selected is now
stored in memory. You can alter the
settings again at any time.
Before you begin, first ensure that:
Check
– The dryer is switched off.
^ Repeat steps A to D.
– The door is closed.
^ Switch the dryer off after step D.
A Press the Start/Stop button and keep
it pressed in whilst carrying out steps
B-C.
B Switch the dryer on.
Wait until the indicator light for the
Start/Stop button lights up constantly. . .
C . . . and then release the Start/Stop
button.
D Press the Gentle tumble button nine
times.
– The Gentle tumble indicator light will
flash slowly once and will then flash
quickly three times.
To select the extended drying levels
^ Select a programme.
^ Press the drying level button
repeatedly until one or two indicator
lights come on.
– Indicator lights Extra dry and Normal
= Normal+
– Indicator lights Hand iron and
Normal = Hand iron+
– Indicator lights Machine iron and
Hand iron = Machine iron+
63
Alteration rights reserved/0313
M.-Nr. 09 402 480 / 00