Zebex Z-3070 Series Specifications

PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
PRODUCT
REFERENCE
MANUAL
Z
-3070 S
eries C
Z-3070
Series
CC
CD
D
B
arcode S
cann
Barcode
Scan
neerr
ZEBEX INDUSTRIES INC. All Rights Reserved.
i
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
Introduction
Z-3070 Series is ZEBEX’s newest developed handheld type barcode
scanner with optional choices of different scan engine, interface, and as
well as the communications.
Important notices
Thank you for purchasing the Z-3070 Series Handheld Barcode Scanner.
To ensure years of reliable service, please read this Product Reference
Manual carefully and use the scanner safely. Store this Product
Reference Manual in a safe location where you can find it for future use.
© Copyright 2002. ZEBEX Industries Inc. All rights reserved.
The information contained in this document is subject to change without
notice.
No liability is assumed with respect to the use of the information
contained in these written materials or software, or for damages resulting
from the use of the information contained in these written materials or of
the software.
No part of these written materials or software may be reproduced or used
in any form or by any means, electronic or mechanical, including
photocopying and recording and the use of any kind of information
storage and retrieval system or translated to another language, without
prior permission in writing from ZEBEX.
ZEBEX INDUSTRIES INC. All Rights Reserved.
i
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
Precautions
General handling precautions
While using the scanner, please take notes to the following handling
precautions.
Do not put the scanner to burn in fire.
Do not put the scanner directly under the sun or by any heat
source.
Do not use or store the scanner in a very humid place.
Do not let the scanner drop or collide violently with other objects.
Do not take apart the scanner without authorization.
ZEBEX INDUSTRIES INC. All Rights Reserved.
ii
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
Contents
Introduction........................................................................................ i
Important notices............................................................................... i
Precautions ....................................................................................... ii
About This Guide
Introduction........................................................................................ vii
Service information............................................................................ vii
Service center ................................................................................... viii
Acquiring information......................................................................... viii
Getting Started With Z-3070
Introduction........................................................................................ 2
Unpacking ......................................................................................... 2
Understanding the scanner parts and functions................................ 3
Installing the cable............................................................................. 4
Power connection.............................................................................. 5
Connecting the scanner to a host...................................................... 6
Getting Ready to Scan with Z-3070
Introduction........................................................................................ 10
Scanning with the Z-3070.................................................................. 10
Aiming ............................................................................................... 10
Scanning mode ................................................................................. 11
Programming and Settings
Introduction........................................................................................ 13
Programming options ........................................................................ 13
Default parameters............................................................................ 13
Default values of operating parameters ...................................... 14
Predefined barcode identifiers .................................................... 14
Default values of keyboard emulation parameters setting .......... 14
Default values of RS-232C serial communication parameters.... 15
Default values of wand emulation parameters ............................ 15
Default values of USB emulation parameters ............................. 15
Default values of decoding parameters....................................... 16
Program procedure ........................................................................... 17
System setting................................................................................... 18
General configuration ........................................................................ 19
Scanning mode selection (for laser scanner).............................. 19
Scanning mode selection (for CCD scanner).............................. 19
Data redundant check ................................................................. 20
Inter-message delay.................................................................... 20
ZEBEX INDUSTRIES INC. All Rights Reserved.
iii
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
Inter-character delay ................................................................... 21
Message/block mode selection ................................................... 21
Send command in block mode communication........................... 22
Good read beeper tone selection................................................ 22
Sound duration............................................................................ 23
Interface configuration....................................................................... 24
RS-232C serial communication parameters setting .................... 24
Handshaking protocol ........................................................... 24
ACK/NAK response time setting ........................................... 24
Baud rate .............................................................................. 25
Data bit.................................................................................. 26
Stop bit.................................................................................. 26
Parity..................................................................................... 26
Message terminator (for RS-232C type only) ....................... 27
Keyboard emulation parameters setting ..................................... 28
Keyboard type selection........................................................ 28
Keyboard language selection................................................ 30
Message terminator (for keyboard wedge use) .................... 31
Keyboard type selection........................................................ 31
Break code on/off setting ...................................................... 32
Function key active on/off ..................................................... 32
Function key emulation ......................................................... 33
00H~1FH ASCII code defined............................................... 33
Wand emulation parameters setting............................................ 34
Emulation speed selection .................................................... 34
Emulation data output selection............................................ 34
Wand emulation narrow/wide ratio........................................ 35
USB interface parameters setting ............................................... 36
Keyboard type....................................................................... 36
Message terminator .............................................................. 36
The symbologies ............................................................................... 37
Reading code selection............................................................... 37
Code 39 parameters setting........................................................ 40
Interleaved 2 of 5 parameters setting.......................................... 41
Chinese post code parameters setting........................................ 42
UPC/EAN/JAN parameters setting.............................................. 43
Codabar/Monarch parameters setting......................................... 47
Code 128 parameters setting...................................................... 48
UCC/EAN 128 parameters setting .............................................. 49
Matrix 25 parameters setting....................................................... 49
MSI/Plessy parameters setting ................................................... 50
ZEBEX INDUSTRIES INC. All Rights Reserved.
iv
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
Italian pharmacy parameters setting ........................................... 52
Barcode length setting ................................................................ 52
ISBN/ISSN conversion ................................................................ 53
Data editing ....................................................................................... 54
Header and trailer ....................................................................... 54
Barcode identifier code setting.................................................... 55
Truncate header/trailer character ................................................ 57
Technical Specifications
Product configuration ........................................................................ 59
Preliminary specifications.................................................................. 60
Special Terms
Terms and definitions ........................................................................ 63
Support and Maintenance
Troubleshooting................................................................................. 69
Customer support.............................................................................. 71
Maintenance...................................................................................... 71
Warranty period and policy................................................................ 72
RMA policy ........................................................................................ 73
Product accessories .......................................................................... 75
Cables ............................................................................................... 75
User’s documentation ....................................................................... 75
Relative publications ......................................................................... 75
Appendix
Appendix A - Code 39 full ASCII code table...................................... 77
Appendix A - Function key emulation................................................ 79
Appendix B - Code 39 full ASCII barcode table ................................ 80
Appendix C - Barcode samples......................................................... 90
Appendix D - Quick settings .............................................................. 91
ZEBEX INDUSTRIES INC. All Rights Reserved.
v
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
ABOUT THIS GUIDE
ZEBEX INDUSTRIES INC. All Rights Reserved.
vi
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
Introduction
The Z-3070 Series Handheld Barcode Scanner Product Reference
Manual provides general instructions for the setup, programming,
operation, troubleshooting, and maintenance of the Z-3070 Series
Handheld Barcode Scanner.
Service information
If you have any problem with the product, you may contact the ZEBEX
representative in your region, or contact ZEBEX offices for customer care.
Please provide the model number and serial number before contact
ZEBEX for service.
If the problem cannot be solved through e-mails or phone calls, ZEBEX
might request you to send the equipment back for checking. If this is
necessary, you will be given specific directions.
ZEBEX will not be responsible for any damage occurred during shipment
if the approved package is not used. To prevent any possibility that
might void the warranty, please make sure the proper shipment container
is used. If necessary, request an original shipping container from
ZEBEX to send to you.
ZEBEX INDUSTRIES INC. All Rights Reserved.
vii
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
Service Center
For ZEBEX services, warranty repairs, and technical assistance, please
contact your sales representative or the following ZEBEX offices.
HEADQUARTERS
CHINA
ZEBEX Industries Inc.
2F, 531-1, Chung Cheng Road,
Hsin Tien City, Taipei, Taiwan
TEL / +886 2 2218 2018
FAX / +886 2 2218 8670
E-MAIL / mail@zebex.com.tw
WEBSITE/ www.zebex.com.tw
ZEBEX Industries (Shanghai)
No 1998, Qixin Road,
Minhang District, Shanghai,
China
Postcode: 201101
TEL / +86 21 5479 4420
FAX / +86 21 5479 4421
E-MAIL / zebex@21cn.net
USA
GERMANY
ZEBEX America Inc.
11 Ilene Court, Unit # 2,
Hillsborough, N.J. 08844
TEL / +1 908 359 2070
FAX / +1 908 359 1272
E-MAIL / sales@zebex.com
WEBSITE / www.zebex.com
ZEBEX Vertriebs-GmbH
Stimpelwiese 2, D-61250,
Usingen, Germany
TEL / +49 1805 258443
FAX / +49 1805 258442
E-MAIL / zebex@zebex.de
WEBSITE / www.zebex.de
Acquiring Information
You may find the newest software, products information, and technical
supports by connecting to ZEBEX web site at http://www.zebex.com.tw.
If the information needed is not found to solve your problem either from
the Product Reference Manual or ZEBEX web site, please contact
ZEBEX customer services for support.
ZEBEX INDUSTRIES INC. All Rights Reserved.
viii
PRODUCT REFERENCE MANUAL
Z-3070 CCD BARCODE SCANNER
GETTING STARTED
WITH Z-3070
ZEBEX INDUSTRIES INC. All Rights Reserved.
1
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Introduction
The Z-3070 Series is the newest developed handheld type barcode
scanner with optional choices of different scan engine, interface, and as
well as the communications.
You can puzzle up your selections with the Z-3070 series to meet your
applications for all kinds of purposes. Selections should be made when
order according to follows:
Z-3070/DC: scans with Dual CCD Engine;
Z-3070/EC: scans with Single CCD Engine;
Z-3070/LR: scans with Long Range Laser Engine;
Z-3070/WA: scans with Wide Angle Laser Engine
Unpacking
Open the package, there should be a scanner and cable. Carefully take
them out of the box. Please make sure both items are the correct ones
as you ordered, and make sure that there is no damage on the cover of
the scanner, and/or the cable.
Contact your supplier or dealer if delivery made is not correct, and/or if
defects found with the scanner or cable.
We highly recommend you to please keep the packing box in case for any
returns or repairs to ZEBEX in the future. ZEBEX will not hold for any
responsibilities for damages occurred during delivery if a non-approved
package material is used.
ZEBEX INDUSTRIES INC. All Rights Reserved.
2
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Understanding the scanner parts and functions
Z-3070 Series Scanner Parts
Parts
Handle
Trigger
Exit Window
Functions
Ergonomically designed for easy holding the
Scanner.
For triggering the scanner
For light exit and engine protection.
When power is on, the LED is RED.
LED Indicator
A barcode is successfully decoded when the
LED indicates GREEN.
Buzzer
The buzzer sounds when a barcode is
successfully decoded.
Cable interface port
For cable connecting.
ZEBEX INDUSTRIES INC. All Rights Reserved.
3
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Installing the Cable
Plug the interface cable modular connector into the cable interface port
on the bottom of Z-3070 Series handle, and twist the SR lock to the right
to lock as shown:
Different cables are required for different host. To change the scanner
cable:
1. Turn the SR lock counter-clockwise to unlock.
2. Pull the cable out of the cable interface port on the bottom of the
scanner handle.
3. Plug a new cable into the cable interface port, and twist the SR lock
to the right.
ZEBEX INDUSTRIES INC. All Rights Reserved.
4
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Power Connection
If your host does not provide power to the scanner, you will need an
external power connection to the scanner:
1. Connect the interface cable to the bottom of the scanner, as
described in Installing the Cable.
2. Connect the other end of the interface cable to the host (refer to
your host manual to locate for correct port).
3. Connect the right-angle connector of power supply into the power
jack on the interface cable. Plug the other end of the power supply
into an AC outlet.
ZEBEX INDUSTRIES INC. All Rights Reserved.
5
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Connecting the scanner to a host
The Z-3070 Series scanner supports RS-232C, keyboard Emulation,
Wand Emulation, and USB interface to a host system. This section
describes how to set up each of these connections.
RS-232C Connection
This connection is made either through RS-232C interface cable with D
type 9 Pin connector or through a RS-232C interface cable with D type 25
Pin connector to the serial port on the host.
1. Connect the RS-232C interface cable to the bottom of the scanner, as
described in Installing the interface Cable.
2. Connect the other end of the interface cable to the serial port on the
host.
3. Connect the power supply.
RS-232C Connection with D type 9 Pin connector
RS-232C Connection with D type 25 Pin connector
ZEBEX INDUSTRIES INC. All Rights Reserved.
6
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Keyboard Emulation Connection
When configured for Keyboard Emulation input, the host accepts input
from the scanner as keystrokes. The Z-3070 Series Scanner can perform
Keyboard Emulation input using a keyboard interface cable and a male to
female connecting cable.
Keyboard Emulation Connection
1.
2.
3.
4.
Connect the Keyboard Emulation interface cable to the bottom of the
scanner, as described in Installing the interface Cable.
Connect the male end of the keyboard cable into the female end of
the interface cable.
Connect the female end of male-to-female connecting cable into the
male end of the interface cable.
Connect the male end of male-to-female connecting cable into the
keyboard port on the host
Wand Emulation Connection
To perform Wand Emulation, the scanner can be connected to a portable
data terminal, or a controller that collects the data as wand data, and
interprets it for the host.
1. Connect the Wand Emulation interface cable to the bottom of the
scanner, as described in Installing the Interface Cable.
2. Connect the other end of the interface cable into the COM port on the
PDT or controller.
3. Plug one end of the power supply cable into the power receptacle on
the interface cable. Plug the other end of the power supply cable into a
wall outlet.
ZEBEX INDUSTRIES INC. All Rights Reserved.
7
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
USB Connection
This connection is made through USB interface cable to the USB port on
the host.
1. Connect the USB interface cable to the bottom of the scanner, as
described in Installing the interface Cable.
2. Connect the other end of the interface cable into the USB port on the
host.
ZEBEX INDUSTRIES INC. All Rights Reserved.
8
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Getting Ready to Scan
With Z-3070
ZEBEX INDUSTRIES INC. All Rights Reserved.
9
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Introduction
This chapter covers some tips about scanning.
Scanning with the Z-3070
1. Ensure all connections are secure and power is on, the LED is
indicating in RED as standby position, and the symbol you want to
scan is within the scanning range.
2. Aim the scanner at the barcode. If your scanner works in trigger mode,
aim and press the trigger.
3. Ensure the scan line crosses every bar and space of the symbol.
4. Upon successful decode, the scanner beeps and the LED indicates
GREEN.
Aiming
Do not hold the scanner directly over the barcode. Scanning light
reflecting directly back into the scanner from the barcode is known as
specular reflection which can make decoding difficult. The area where
specular reflection occurs is known as a “dead zone”.
You can tilt the scanner up to 65° forward or backward and achieve a
successful decode. Simply practice quickly to find what tolerances to
work within.
ZEBEX INDUSTRIES INC. All Rights Reserved.
10
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Scanning mode
Z-3070/DC and Z-3070/EC supports 4 scanning option, but Z-3070/LR
and Z-3070/WA supports 2 scanning option.
Refer to Programming and Setting for the specific barcode programming
information. When power is on for the first time, Z-3070 Series Scanner
is working in default scanning mode. You may change it to the appropriate
mode.
ZEBEX INDUSTRIES INC. All Rights Reserved.
11
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
PROGRAMMING
AND SETTINGS
ZEBEX INDUSTRIES INC. All Rights Reserved.
12
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Introduction
Scanning a series of programming barcode labels can configure the
Z-3070 series scanners. This allows decoding options and interface
protocols to be tailored to a specific application. The configuration is
stored in non-volatile memory and will not be lost by removing power from
the scanner.
The scanner must be properly powered before programming. For
RS-232C type scanners, an external power adapter must be used to
supply DC power to the scanner. If a keyboard emulation type scanner
is used with a IBM PC/XT/AT, PS/2 or any fully compatible computers,
power will be drawn from the keyboard port. No external power adapter
is required. If keyboard emulation type scanner is used with any other
non IBM PC compatible computers, an external power adapter may be
needed.
Programming Options
Programmable options are divided into four groups.
The first group includes the options that show the general behavior of the
laser scanner. The second group of options governs the operation of
RS-232C type serial ports. The third group selects the keyboard type
that the keyboard emulation type will be emulated. The last group sets
the decoding parameters for each barcode symbology.
Default Parameters
This table gives the default settings of all the programmable parameters.
The default settings will be restored whenever the “Reset” programming
label is scanned and the laser scanner is in programming mode.
ZEBEX INDUSTRIES INC. All Rights Reserved.
13
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
DEFAULT VALUES OF OPERATING PARAMETERS
Function
Default Values
Scanning Mode Selection
Trigger mode
Header and Trailer
None
Inter-Message Delay
Normal
Inter-Character Delay
Normal
Message/Block Mode Selection
Message
Send Command in Block Mode
Disable
Communication
Good Read Beeper Tone Selection
2.3KHz/50 msec
Code Identifier Transmitting
Disable
PREDEFINED BARCODE IDENTIFIERS*
Code 39 Barcode Identifier Code
ITF 2 of 5 Barcode Identifier Code
Chinese Post Code Identifier Code
UPC-E Barcode Identifier Code
UPC-A Barcode Identifier Code
EAN-13 Barcode Identifier Code
EAN-8 Barcode Identifier Code
Coda bar Barcode Identifier Code
Code 128 Barcode Identifier Code
Code 93 Barcode Identifier Code
MSI Barcode Identifier Code
MATRIX 25 Barcode Identifier Code
M
I
H
E
A
F
FF
N
K
L
P
G
*For activation of barcode identifiers see page 54
DEFAULT VALUES OF KEYBOARD EMULATION PARAMETERS
SETTING
Function
Keyboard type
selection
Message
terminator
Default Values
IBM PC/AT USA
Enter/ carriage
Return
ZEBEX INDUSTRIES INC. All Rights Reserved.
14
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
DEFAULT VALUES OF RS-232C SERIAL COMMUNICATION
PARAMETERS
Function
Handshaking
protocol
ACK/NAK
response time
setting
Baud rate
Data bit
Stop bit
Parity
Message
terminator
selection
Default Values
None
300 msec
9600
8
1
Mark (None)
CR/LF
DEFAULT VALUES OF WAND EMULATION PARAMETERS
Function
※ Wand emulation speed
※ Wand emulation output
Default Values
Normal
Black = High
Note: For wand emulation, the configuration is only effective for the items with asterisk (※).
DEFAULT VALUES OF USB EMULATION PARAMETERS
Function
※ Keyboard Type
※ Message Terminator
Default Values
US Keyboard
Enter
Note: For USB emulation, the configuration is only effective for the items with asterisk (※).
ZEBEX INDUSTRIES INC. All Rights Reserved.
15
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
DEFAULT VALUES OF DECODING PARAMETERS
Function
Code
Code 39
ITF 2 of 5
Chinese Post Code
UPC/EAN/JAN
Coda bar
※
MSI
Reading codes
Code 128
Selection
Code 93
※
ITAT
※
EAN-128
※ MATRIX 25
※ Italian Pharmacy
ISSN/ ISBN
Codes
Start/stop characters
Code 39
Check digit
Concatenation
Interleaved
Length
2 of 5
Check digit
Chinese Post
Length
Code
Check digit
Format
Addendum
UPC-E=UPC-A
UPC/EAN/JAN
UPC-A leading digit
UPC-A check digit
UPC-E leading digit
UPC-E check digit
Type
Coda bar
Start/stop characters
Length
FNC 2 append
Code 128
Check digit
Length
MSI
Check digit
Italian Pharmacy Transmit "A" Character
Length
MATRIX 25
Check digit
Default Value
Enable
Enable
Disable
Enable
Enable
Disable
Enable
Enable
Disable
Disable
Disable
Disable
Disable
Standard
Not transmitting
Disabled
Off
6-32 digits
Disable
10~16 digits
Transmit
All
Disable
Disabled
Transmit
Transmit
Transmit
Transmit
Standard
A, B, C, D
6~32 digits
Disable
Disable
Variable
Transmit
Not transmitting
Fix 10 digits
Disable
Note: The configuration of the items with asterisk (※) is effective when being appointed in advance.
ZEBEX INDUSTRIES INC. All Rights Reserved.
16
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
PROGRAM PROCEDURE
ZEBEX INDUSTRIES INC. All Rights Reserved.
17
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
SYSTEM SETTING
Start of Configuration
The reading of the “RESET” label turns
all the parameters back to default
values.
RESET
ABORT
When you intend to turn your scanner
back to default parameters, please
scan the “Start of Configuration” label
first, then scan “RESET” label and
finally scan the “End of Configuration”
label.
The reading of the "ABORT" label
discards all the parameters read prior
to the "End of configuration".
RS-232C
PC/AT
USB
The scanner remains in the last
interface mode when the scanner is
reset. The label below should be
scanned if the scanner is configured
the first time.
WAND EMULATION
SHOW VERSION
The reading of the “SHOW VERSION”
label will be show firmware version.
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
18
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
GENERAL CONFIGURATION
Start of Configuration
End of Configuration
SCANNING MODE SELECTION (for laser scanner)
For series laser scanners, there are 2 scanning modes to suit your
application requirements.
Trigger Mode
Pulse Mode
The scanner becomes inactive as soon as
the data is transmitted.
It must be
triggered to become active again.
The scanner will light up when press the
pulse mode trigger switch once. And, the
scanner will turn off for next pressing.
SCANNING MODE SELECTION (For CCD scanner)
The scanner becomes inactive as soon as
the data is transmitted.
It must be
triggered to become active again.
In auto scan mode, the scanner is still
active after the data is transmitted, but the
successive transmission of the same bar
code is not allowed when the trigger switch
is pressed again.
This scanner will light up when press the
scanner trigger switch once. And, the
scanner will turn off for next pressing.
This mode is similar to Auto scan mode,
but double reading for the same barcode is
prohibited if the scanner switch is pressed.
ZEBEX INDUSTRIES INC. All Rights Reserved.
19
Trigger mode
Auto scan mode
Alternate mode
Repeat mode
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
DATA REDUNDANT CHECK
Enable
The option allows you to set decoder data
redundant check.
Disable
INTER-MESSAGE DELAY
These series of scanners allow you to add a delay between two
consecutive messages. This delay will be added before each data
transmission.
None
100 msec
500 msec
1 Second
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
20
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
INTER-CHARACTER DELAY
This option governs delay time between consecutive characters.
Scanning the following labels can alter the delay time.
None
20 msec
10 msec
50 msec
MESSAGE / BLOCK MODE SELECTION
This option allows you to treat scanned data as either an independent
message or a block message. In the message mode, the data scanned
will be transmitted immediately. In block mode, the data scanned will
be appended to the message buffer if the scanner is programmed in
block mode. A block of message will only be transmitted after a “Send”
command is entered. This mode is only available when the scanner is
working with code 39 labels. You are free to choose any character as
the “ Send” command.
Message
Block
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
21
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
SEND COMMAND IN BLOCK MODE COMMUNICATION
You can use this option to set your own “Send” command used in block
mode communication.
Enable
Store
Disable
Set
GOOD READ BEEPER TONE SELECTION
You can use this option to set frequency and / or duration of the buzzer
after successful reading.
Medium
Low
High
Disable
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
22
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
SOUND DURATION
long(120 ms)
Medium(50 ms)
Short(20 ms)
Very short(5 ms)
*For Alpha-70 ,Z-3070 and SC-2070 Series only Medium and disable
setting available, it’s hardware beeper control.
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
23
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
INTERFACE CONFIGURATION
Start of Configuration
RS-232C SERIAL COMMUNICATION PARAMETERS SETTING
The RS-232C scanner supports four handshaking protocols. With these
options of communication protocol, you can tailor the scanner to meet the
requirement of most systems.
HANDSHAKING PROTOCOL
None
RTS/CTS
ACK/NAK
Xon/Xoff
ACK/NAK RESPONSE TIME SETTING
300 msec
2 sec
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
24
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
ACK/NAK RESPONSE TIME SETTING (Continued)
500 msec
3 sec
1 sec
5 sec
BAUD RATE
19200
9600
4800
2400
1200
600
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
25
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
DATA BIT
7
8
STOP BIT
1
2
PARITY
Even
Odd
Mark
Space
None
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
26
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
MESSAGE TERMINATOR (FOR RS-232C TYPE ONLY)
None
CR/LF
CR
LF
H Tab
STX/ETX
EOT
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
27
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
KEYBOARD EMULATION PARAMETERS SETTING
Start of Configuration
KEYBOARD TYPE SELECTION
The keyboard emulation scanners can emulate a number of personal
computers keyboard and a number of terminal keyboard. Keyboard
emulation is activated whenever you have selected the type of keyboard
for which the scanner is going to emulate. Choose the appropriate type of
keyboard emulation by scanning the labels under the following labels.
IBM AT
PS/2 30-80
IBM 5550
IBM 5295 Terminal
IBM XT
IBM 5530-SC
IBM 5530-ZC
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
28
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
KEYBOARD TYPE SELECTION (Continued)
NEC 9801
IBM 3196 Terminal
APPLE MAC II(※)
IBM 3477/3472 Terminal
PS2/30/56
IBM 3477 Terminal
(Without break code)
NEC 5200(※)
Note: The configuration of the items with asterisk (※) is optional.
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
29
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
KEYBOARD LANGUAGE SELECTION
USA
UK
Germany
French
Spanish
Italian
Swiss
Swedish
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
30
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
MESSAGE TERMINATOR (FOR KEYBOARD WEDGE USE)
None
Return /Enter
Hor. TAB
Execute
KEYBOARD TYPE SELECTION
Scan Code Mode
Alt mode
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
31
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
BREAK CODE ON/ OFF SETTING
(FOR IBM Terminals 31xx, 34xx, 37xx USE)
To select the interface for these IBM terminals, read the correct key
transmission code.
ON
OFF
FUNCTION KEY ACTIVE ON/ OFF (FOR IBM AT USE)
Function keys can be concatenated with input data as header and/or
trailer. See table on page 75.
ON
OFF
CAPITAL LOCK ON/ OFF
Select the suitable code to match your keyboard caps lock status.
ON
OFF
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
32
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
Function key emulation (only for PC/AT)
Numlock on/off
OFF
ON
00H~1FH ASCII Code defined
Alt-mode code
Crtl+code
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
33
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
WAND EMULATION PARAMETERS SETTING
Start of Configuration
EMULATION SPEED SELECTION
Low
Medium
Normal
High
Higher
EMULATION DATA OUTPUT SELECTION
The decoded data output logic level can be set to befit the external
decoder.
Black = High
Black = Low
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
34
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
WAND EMULATION NARROW / WIDE RATIO
1:2
1:3
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
35
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
USB INTERFACE PARAMETERS SETTING
Start of Configuration
The USB mode is effectively a keyboard emulator that works with hosts
that USB-compatible operating system and USB ports.
USB
compatible operating systems are Windows 98, Windows NT 5.0 and
Mac OS 8 and later, no additional software is needed since the USB
driver support is built into this operating system.
KEYBOARD TYPE
US Keyboard
International Keyboard
MESSAGE TERMINATOR
None
Enter
H Tab
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
36
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
THE SYMBOLOGIES
Start of Configuration
READING CODE SELECTION
Code 39 Enable
Code 39 Disable
Coda bar Enable
Coda bar Disable
UPC/ EAN/ JAN Enable
UPC/ EAN/ JAN Disable
ITF 2 of 5 Enable
ITF 2 of 5 Disable
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
37
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
READING CODE SELECTION (Cont’d)
Chinese Post Code Enable
Chinese Post Code Disable
Code 128 Enable
Code 128 Disable
MSI Enable
MSI Disable
Code 93 Enable
Code 93 Disable
IATA Enable
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
38
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
READING CODE SELECTION (Cont’d)
IATA Disable
EAN- 128 Enable
EAN-128 Disable
MATRIX 25 Enable
MATRIX Disable
Italian Pharmacy Enable
Italian Pharmacy Disable
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
39
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
CODE 39 PARAMETERS SETTING
CHARACTER SET
Standard Code 39
Full ASCII Code 39
START/STOP CHARACTER TRANSMISSION
Yes
No
CHECK DIGIT
Calculate and Transmit
Calculate but not Transmit
NO
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
40
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
CODE 39 PARAMETERS SETTING (continued)
CONCATENATION
Enable
Disable
INTERLEAVED 2 OF 5 PARAMETERS SETTING
Examples: Felting length 4 to 8 digits
LENTGTH
Scan:. Start of
configuration
max
Min
0
0
8
MAX
Min
4
set
set
End of
configuration
Set
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
41
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
CHECK DIGIT
NO
Calculate and Transmit
Calculate but not Transmit
CHINESE POST CODE PARAMETERS SETTING
LENGTH
Scan:. Start of
configuration
max
Min
0
0
8
4
set
set
End of
configuration
MAX
MIN
Set
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
42
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
CHECK DIGIT
NO
Calculate and Transmit
Calculate but not Transmit
UPC/EAN/JAN PARAMETERS SETTING
FORMAT
All
EAN-8 or EAN-13
UPC-A and EAN-13
UPC-A and UPC-E
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
43
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
FORMAT (Continued)
UPC-A
UPC-E
EAN-13
EAN-8
ADDENDUM
NO
5 Characters
2 Characters
2 or 5 Characters
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
44
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
FORCE UPC-E TO UPC-A FORMAT
Yes
No
FORCE UPC-A TO EAN-13 FORMAT
Yes
No
TRANSMIT UPC-A LEADING CHARACTER
Yes
No
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
45
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
TRANSMIT UPC-A CHECK DIGIT
Yes
No
TRANSMIT UPC-E LEADING CHARACTER
Yes
No
TRANSMIT UPC-E CHECK DIGIT
Yes
No
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
46
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
TRANSMIT EAN-13 CHECK DIGIT
Yes
No
TRANSMIT EAN-8 CHECK DIGIT
Yes
No
CODABAR/ MONARCH PARAMETERS SETTING
START/ STOP CHARACTER TRANSMISSION
No
DC1~DC4
A, B, C, D
a/ t, b/ n, c/ *, d/ e
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
47
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
CONCATENATION
Enable
Disable
CODE 128 PARAMETERS SETTING
FNC 2 CONCATENATION
Enable
Disable
CHECK DIGIT
No
Calculate and Transmit
Calculate but not Transmit
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
48
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
UCC/EAN128 PARAMETERS SETTING
The character FNC1 can be transmitted or not using these codes.
FNC1 Character Transmitted
FNC1 not Transmitted
MATRIX 25 PARAMETERS SETTING
Examples: Felting length 4 to 8 characters
Scan. Start of
configuration
max
Min
0
0
8
4
set
set
End of
configuration
MAX
MIN
Set
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
49
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
MSI/PLESSY PARAMETERS SETTING
Examples: Felting length 4 to 8 characters
Scan:. Start of
configuration
max
Min
0
0
8
4
set
set
End of
configuration
MAX
MIN
SET
Double Check digit
Calculate but not Transmitted
No
Calculate but only first one Transmitted
Calculated and both Transmitted
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
50
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
Double Check digit (Cont’d)
Single Check digit
Calculated but not Transmitted
Calculated and transmitted
PLESSY CODE SETTING
Calculated and transmitted
Calculate but not transmitted
CHECK DIGHT
No
Calculate and Transmit
Calculate but not Transmit
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
51
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
ITALIAN PHARMACY PARAMETERS SETTING
TRANSMIT "A" CHARACTER
Yes
No
BARCODE LENGTH SETTING
CODE 39 LENGTH SETTING
MAX
MIN
CODE 93 LENGTH SETTING
MAX
MIN
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
52
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
CODE 128 LENGTH SETTING
MAX
MIN
CODABAR LENGTH SETTING
MAX
MIN
SET
ISBN/ ISSN CONVERSION
The function convents the UPC/EAN codes appearing on books and
magazine not ISBN/ISSN format.
ACTIVE ISBN/ ISSN
INACTIVE ISBN/ ISSN
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
53
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
DATA EDITING
Start of Configuration
HEADER AND TRAILER
This option allows you to append a header and/or a trailer to every
message transmitted via the serial ports or the keyboard port. There is
no restriction in selecting header or trailer characters as far as the sum of
the lengths of header and trailer is not greater than 10 digits.
Header
1. Select either header or trailer you are going
to program by scanning the corresponding
label
Trailer
2. Scan the character(s) you want from the
enclosed ASCII table to set as header or
trailer (be sure to enable full ASCII code 39
option before you start).
Set
3. Read the “Set” label to set your choice into
memory.
BARCODE IDENTIFIER CODE SELECTION
The series of scanners can transmit max.2-digit barcode identifier code
for different types of barcodes. Use the labels to choose transmit or
not transmit predefined barcode identifier code (ID’s are listed on page
14):
Enable
Disable
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
54
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
BARCODE IDENTIFIER CODE SETTING
Each of the series type scanners can set max.2 digits as barcode
identifier code according to different barcode. The procedure is as
follows:
1. Scan “Start of configuration” label
2. Scan “Barcode identifier setting code” label.
3. Scan the new code mark from ASCII table (max. two digits). For
example, if one “AB” want for code mark then scan “A” and “B”.
4. Scan “Set” label.
5. Scan “ End of configuration” label.
UPC-E
UPC-A
EAN-13
EAN-8
Chinese post code
ITF 2 OF 5
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
55
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
BARCODE IDENTIFIER CODE SETTING (Cont’d)
Coda bar
Code 39
Code 128
Code 93
MSI
MATRIX 25
Set
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
56
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Start of Configuration
Truncate Header/Trailer Character
(Version az1.24, dz1.05, ac1.01, dz1.05,pl1.39 or higher is required)
You can truncate a number header or trailer for a symbology. When you
do, the specific character you select is deleted from the symbology you
want.
1. scan ”start of configuration”
Truncate header
character
Truncate trailer
character
set
2. select “truncate header” or “truncate
trailer”
3. scan two barcode value from the full
ASCII code table(0~9) For example, if
2 number header you want clear then
scan ”0” and “2”
4. Scan” set” barcode
5. end of configuration
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
57
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Technical Specifications
ZEBEX INDUSTRIES INC. All Rights Reserved.
58
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Product Configuration
Single Dual
Model Number
CCD CCD
◎
Z-3070-DC
Z-3070-EC
◎
◎
Z-3070-EC/TG
Z-3071-WA
Z-3071-WA/RF
Z-3071-LR/TG
11”
160mA@5.0V
30°
150
30%
6”
160mA@5.0V
◎
30°
300
30%
11”
180mA@5.0V
◎
30°
150
30%
6”
180mA@5.0V
◎
30°
300
30%
11”
200mA@5.0V
◎
30°
150
30%
6”
200mA@5.0V
53°
36
35%
10”
160mA@5.0V
23°
36
35%
20”
200mA@5.0V
◎
53°
36
35%
10”
160mA@5.0V
◎
23°
36
35%
20”
200mA@5.0V
◎
53°
36
35%
10”
200mA@5.0V
◎
23°
36
35%
20”
200mA@5.0V
◎
◎
◎
◎
Z-3071-LR/RF
Z-3071-WA/TG
30%
◎
Z-3071-LR
ReadScan PCS* ing
Power Supply
Rate Value Distance
300
◎
Z-3070-DC/TG
Scan
Angle
30°
◎
Z-3070-DC/RF
Z-3070-EC/RF
WA
LR
RF
RFID
Laser Laser commu- tag
engine engine nication reader
◎
◎
* Note: Based on UPC/EAN 100%, PCS=90
ZEBEX INDUSTRIES INC. All Rights Reserved.
59
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Preliminary Specifications
Temperature
a) Operating: 0℃ ~ 50℃
b) Storage: -10℃ ~ 60℃
Humidity
a) Operating: 10% ~ 90% (No dewing allowed)
b) Storage: 5% ~ 95% (No dewing allowed)
Shock
1.0 meter drop to concrete
Maximum Ambient
4500 Lux Max (Fluorescence)
Light Rejection
86000 Lux Max (Sunlight)
Laser Safety
CDRH class II / IEC 825-1 class I (WA series)
CDRH class IIIa (LR series)
Interface
Keyboard emulation, C-MOS serial, RS-232C
serial and USB interface
IBM PC/XT/AT, IBM PS/2 Model 30-80, IBM 5550,
Keyboard Emulations 5530-SC, 5530-ZC, IBM 3196, 3472/3477, 5295
Terminal, NEC 9801, Apple MAC II, and more…
UPC A/E, EAN-8/JAN-8, EAN-13/JAN-13, Full
ASCII Code 39, Code 39, Code 93, interleaved 2
Decoding Capabilities of 5, Coda bar, Code 1288, Chinese postcode
Optional: IATA, EAN-128, Code 11, STD 2 of 5,
MSI Plessy, Matrix 2 of 5.
Technology
13.56 MHZ
Reads
Gem
Wave
Transponders from Gem
RFID
Transponder Transponders
Plus, Ario 10 and Ario 40.
Read/Write Electronic
Optional: I code and Tag
(For Tag Series)
it.
24 Kbit / Sec. (Write and
Read / Write Speed
back of 2 Kbit > 1.5 sec)
Read / Write Distance Up to 100mm
ZEBEX INDUSTRIES INC. All Rights Reserved.
60
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Preliminary Specifications (Cont’d)
Frequency Baud
433 and 915 MHZ
Modulation Method
FSK (Frequency Shift Keying)
Data Rate
Up to 19.2K baud
Radio Specification
Power Output
(For RF Series)
Maximum 10mW
Radio Range
30 meters
Channel selection
Software ID selection
Electrical
Complies with EN300 200
and FCC FCR47 and 15
Programmable
Characters
Built-in Decoder:
Type of interface
Code type selection, check digit selection
Decoding option
Transmitted character delay
Header selection, trailer selection
Good read beep tone and volume
Barcode identifier
Keyboard Emulation Configuration:
Inter-message delay, keyboard type and keyboard
language.
Serial Interface Type:
ACK/NAK, Xon/Xoff, RTS/CTS,
Weight
180g (excluding cable and connector)
Case Material
ABS plastic
Cable
Coiled cable, 3m when straightened
Connector Type
RJ-45 Phone Jack Connector
ZEBEX INDUSTRIES INC. All Rights Reserved.
61
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Special Terms
ZEBEX INDUSTRIES INC. All Rights Reserved.
62
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Terms and Definitions
TERMS
DEFINITIONS
ASCII
American standard Code For Information Interchange.
A 7 bit-plus-parity code representing 128 letters,
numerals, punctuation marks, and control characters.
It is a standard data transmission code in the U.S.
Bar
The dark element in a printed barcode symbol.
Baud Rate
A measure of the data flow or number of signaling
events occurring per second. When one bit is the
standard “event”, this is a measure of bits per second
(bps). For example, a baud rate of 9600 means
transmission of 9600 bits of data per second.
Bit
Binary digit. One bit is the basic unit of binary
information. Generally, eight consecutive bits compose
one byte of data. The pattern of 0 and 1 values within
the determines its meaning.
Byte
On an addressable boundary, eight adjacent binary
digits (0 and 1) combined in a pattern to represent a
specific character or numeric value.
Bits are
numbered from the right, 0 through 7, with bit 0 the low
order bit. One byte in memory is used to store one
ASCII character.
CDRH
Center for Devices and Radiological Health. Federal
agency responses for regulating laser product safety.
This agency specifies various laser operation classes
based on power output during operation.
Character
A pattern of bars and spaces which either directly
represents data or indicates a control function, such as
a number, letter, punctuation mark, or communications
control contained in a message.
ZEBEX INDUSTRIES INC. All Rights Reserved.
63
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Character Set
Those characters available for encoding in a particular
barcode symbology.
Check Digit
A digit used to verify a correct symbol decodes. The
scanner inserts the decoded data into an arithmetic
formula and checks that the resulting number matches
the encoded check digit. Check digits are required for
UPC but are optional for other symbologies. Using
check digits decreases the chance of substitution
errors when a symbol is decoded.
Codabar
A discrete self-checking code with a character set
consisting of digits 0 to 9 and six additional character
(-$:/,+).
Code 128
A high-density symbology that allows the controller to
encode all 128 ASCII characters without adding extra
symbol elements.
Code 3 of 9
(Code 39)
A versatile and widely used alphanumeric barcode
symbology with a set of 43 character types, including
all uppercase letters, numerals from 0 to 9, and 7
special character (-./+$ and space). The code name
is derived from the fact that 3 of 9 elements
representing a character are wide, while the remaining
6 are narrow.
Code 93
An industrial symbology compatible with Code 39 but
offering a full character ASCII set and a higher coding
density than Code 39.
Code Length
Number of data characters in a bar code between the
start and stop character, not including those
characters.
Continuous
Code
A barcode or symbols in which all spaces within the
symbol are parts of characters. There are no
intercharacter gaps in a continuous code. The
absence of gaps allows for greater Information density.
ZEBEX INDUSTRIES INC. All Rights Reserved.
64
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Dead Zone
An area within a scanner’s field of view, in which
speculum reflection may prevent a successful decode.
Decode
To recognize a bar code symbology (e.g. UPC/EAN )
and then analyze the content of the specific bar code
scanned.
EAN
European Article Number. This European /
international version of the UPC provides its own
coding format and symbology standards. Element
dimensions are specified metrically. EAN is used
primarily in retail.
Element
Generic term for a bar or space.
Encoded Area
Total linear dimension occupied by all characters of a
code patter, including start/stop characters and data.
Host computer
A computer that serves other terminals in a network,
providing such services as computation, database
access, supervisory programs and network control.
Intercharacter
Gap
The space between adjacent bar code characters in a
discrete code.
Interleaved
Barcode
A bar code in which characters are paired together,
using bars to represent the first character and the
intervening spaces to represent the second.
Interleaved
2 of 5
A binary bar code symbology representing character
pairs in groups of five bars and five interleaved
spaces. Interleaving provides for greater information
density. The location of the wide elements
(bar/spaces) within each group determines which
characters are encoded. This continuous code type
uses no intercharacter spaces. Only numeric (0 to 9)
and START/STOP characters may be encoded.
LED indicator
A semiconductor diode (LED – Light Emitting Diode)
uses as an indicator, often in digital displays. The
semiconductor uses applied voltage to produce light of
ZEBEX INDUSTRIES INC. All Rights Reserved.
65
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
a certain frequency determined by the semiconductor’s
particular chemical composition.
MIL
1 mil = 1 thousandth of an inch.
Parameter
A variable that can have different values assigned to it.
Percent Decode
The average probability that a single scan of a barcode
would result in successful decode. In a well-designed
barcode scanning system, that probability should
approach near 100%.
Print Contrast
Signal ( PCS )
Measurement of the contrast (brightness difference)
between the bars and spaces of a symbol. A minimum
PCS value is needed for a barcode symbol to be
scannable. PCS=(RL-RD)/RL, where RL is the
reflectance factor of the background and RD the
reflectance factor of the dark bars.
Programming
Mode
The state in which a scanner is configured for
parameter values.
Quiet Zone
A clear space, containing no dark marks, which
precedes the start character of barcode symbol and
follows the stop character.
Reflectance
Amount of light returned from an illuminated surface.
Scan Area
Area intended to contain a symbol.
Scanner
An electronic device used to scan barcode symbols
and produce a digitized pattern that corresponds to the
bars and spaces of the symbol. Its three main
components are:
1. Light source (laser or photoelectric cell) illuminates a barcode.
2. Photodetector – registers the difference in
reflected light (more light reflected from space).
3. Signal conditioning circuit – transforms optical
detector output into a digitized bar pattern.
ZEBEX INDUSTRIES INC. All Rights Reserved.
66
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Scanning mode
The scanner is energized, programmed, and ready to
read a bar code.
Space
The lighter element of a bar code formed by the
background between bars.
Speculum
Reflection
The mirror-like direct reflection of light from a surface,
which can cause difficulty decoding a barcode.
Start/Stop
Character
A pattern of bars and spaces that provides the scanner
with start and stop reading instructions and scanning
direction. The start and stop characters are normally to
the left and right margins of a horizontal code.
Symbol
A scannable unit that encodes data within the
conventions of a certain symbology, usually including
start/stop characters, quiet zones, data characters, and
check characters.
Symbol Aspect
Ratio
Symbol Height
The ratio of symbol height to symbol width.
Symbol Length
Length of symbol measured from the beginning of the
quiet zone (margin) adjacent to the start character to
the end of the quiet zones (margin) adjacent to a stop
character.
Symbology
The structural rules and conventions for representing
data within a particular bar code type (e.g. UPC/EAN,
Code 39).
Tolerance
Allowable deviation from the nominal bar or space
width.
UPC
Universal Product Code. A relatively complex
numeric symbology. Each character consists of two
bars and two spaces, each of which is any of four
widths. The standard symbology for retail food
packages in the United States.
The distance between the outside edges of the quiet
zones of the first row and the last row.
ZEBEX INDUSTRIES INC. All Rights Reserved.
67
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Support and
Maintenance
ZEBEX INDUSTRIES INC. All Rights Reserved.
68
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Troubleshooting
Problem
Possible Causes
No power to the scanner.
Nothing
happens
when you follow the
operating instructions.
Possible Solutions
Check the system power.
Ensure the power supply is
connected
if
your
configuration requires a
power supply.
Interface/power cables are Check for loose
loose.
connections.
cable
Be sure the scanner is
Scanner is not programmed
programmed to read the
for the correct barcode
type of barcode you are
type.
scanning.
Light comes on. But
symbol
does
not Barcode
symbol
decode.
unreadable.
Check the symbol to make
is sure it is not defaced. Try
scanning test symbols of
the same barcode type.
Distance between scanner Move the scanner closer to
and barcode is incorrect.
or further from the barcode.
Symbol Is decoded,
Scanner is not programmed Scan the appropriate host
but not transmitted to
for the correct host type.
type barcode.
the host.
ZEBEX INDUSTRIES INC. All Rights Reserved.
69
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Be sure proper host type is
selected.
For RS-232C, ensure the
scanner’s communication
parameters
match
the
host’s settings.
Scanner is not programmed
Scanned
data
is to work with the host.
incorrectly displayed Check Z-3070 Series host
type parameters or editing
on the host.
options.
For keyboard emulation
configuration. Ensure the
system is programmed for
the correct keyboard type.
And the CAPS LOCK key is
off.
Be sure editing options (e.g.
UPC-E
to
UPC-A
Conversion) are properly
programmed.
Note: If after performing the checks, but the symbol still can’t be scanned, please contact your
distributor or Zebex Industries Inc. for further technical support.
ZEBEX INDUSTRIES INC. All Rights Reserved.
70
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Customer support
Support is provided when you contact ZEBEX Industries Inc Technical
Support.
Monday – Friday:8:30 AM to 6:00 PM, Taiwan Time
Phone:(886) 2 2218 2018
Fax:(886) 2 2218 8670
E-mail:mail@zebex.com.tw
ZEBEX provides on-line support for software upgrades, utility programs,
and other information via the internet by:
WWW:http://www.zebex.com.tw
Outside Taiwan, contact your authorized ZEBEX distributor.
Maintenance
Cleaning the exit window is the only maintenance required. A dirty
window may affect scanning accuracy.
◆ Do not allow any abrasive material to touch the window
◆ Remove any dirt particles with a damp cloth
◆ Do not spray water or other cleaning liquids directly into the
window
◆ Wipe the window using a tissue moistened with ammonia / water
ZEBEX INDUSTRIES INC. All Rights Reserved.
71
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Warranty period & policy
1. The warranty period begins on the date of the original Invoice.
2. The warranty period is not a result of an accident, physical damage and
force of nature such as fire, floods, wars…etc.
3. ZEBEX INDUSTRIES INC. reserved the rights to or not to repair for the
Out of Warranty products or the Insubstantial Warranty *.
The warranty service terms will be based on this warranty period as
described below:
UNDER WARRANTY
Regular Warranty -No labors & parts will be charged. (Warranty Begins at
date of the original invoice Buyers are requested to return the defective
products to ZEBEX on their expense.)
ZEBEX INDUSTRIES INC. All Rights Reserved.
72
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
RMA Policy
1. The Return Merchandise Authorization (RMA) is for any ZEBEX
INDUSTRIES INC. product that is returned for repair or for
replacement within the warranty period. ZEBEX INDUSTRIES INC.
must give an RMA number to the customer before the customer is
authorized to return any defective product to ZEBEX INDUSTRIES
INC.
2. It is necessary to have a RMA number for any items returning to
ZEBEX INDUSTRIES INC.. In order to obtain a RMA number from the
Customer Service Department, it must have following information
ready:
Customer name
Contact person
Apply date,
Telephone number
Fax number
Email address
Sales Rep.
Shipping address
Product model
Serial number
Quantity
Defect description for each item (very important!!!)
Without above information, ZEBEX INDUSTRIES INC. has right not
to issue a RMA number to the customer. In order to get a RMA
number, you can:
i. Call + 886 - 2 - 2218 - 2018 during business hour.
ii. Fax the RMA Request Form to + 886 - 2 - 2218 - 8670
iii. E-mail to Sales Rep. of Zebex.
Local:
Jeffrey Wu - E-mail: sales-d1@zebex.com.tw
Angela Chu – E-mail: sales-d7@zebex.com.tw
Overseas:
Jenny Hsu (Ext: 2107) - E-mail: sales-d2@zebex.com.tw
Florence Wu (Ext: 2113) - E-mail: sales-d3@zebex.com.tw
ZEBEX INDUSTRIES INC. All Rights Reserved.
73
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Felix Liang (Ext: 2114) - E-mail: sales-d4@zebex.com.tw
Eugene Chen (Ext: 2115) - E-mail: sales-d5@zebex.com.tw
Johnny Chang (Ext: 2108) - E-mail: sales-d6@zebex.com.tw
3. Each item returning for RMA must be attached a photocopy of RMA
Request Form.
4. The warranty period is not a result of man-made remissness,
improper operation, physical damage and force of nature such as fire,
floods, wars…etc.
5. After the customer has confirmed the RMA number sent by
ZEBEX INDUSTRIES INC. The RMA will be sent back within 2 weeks
upon receiving goods.
6. It is required the RMA number to be written on each shipping
box. Returns must be shipped freight prepaid. The return RMA
shipment must be enclosed with Invoice and Packing List. Returns
not meeting all these conditions will be refused and returned at
customer's expense. And all collect shipments will be refused.
7. The RMA lot will then have a visual inspection upon receipt by
ZEBEX INDUSTRIES INC.. If the item or quantity is different from
those listed on the RMA Request Form, ZEBEX INDUSTRIES INC.
shall immediately notify customer of such discrepancy. If customer
made no comment on said ZEBEX INDUSTRIES INC. receiving
report; such quantity and model shown on receiving report becomes
final.
8. Any sale that agrees with NO RMA or with RMA Free Buffer Parts
will not suitable with this RMA Policy.
ZEBEX INDUSTRIES INC. All Rights Reserved.
74
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
Product Accessories
Depending on your host system’s configuration, the following items may
be included with your scanner. These items are also available through
your local Zebex representative or business partner.
Standard Accessories
Standard accessories include a cable and a reference manual for Z-3070
Series.
Optional Accessories
Optional accessories include a hands-free stand for scanning in
hands-free mode, which are supplied at extra cost.
Cables
◆
◆
◆
◆
◆
◆
Power supply
RS-232C Cable (with D type 9 Pin connector)
RS-232-C Cable (with D type 25 Pin connector)
Keyboard Emulation Cable
Wand Emulation Cable
USB Cable
User Documentation
The following user documentation is provided with your scanner:
◆ Reference Manual for Z-3070 Series
Relative Publications
For the latest versions of the Z-3070 Series Reference Guide and Product
Reference Guide, go to : http://www.zebex.com.tw for update.
ZEBEX INDUSTRIES INC. All Rights Reserved.
75
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX
ZEBEX INDUSTRIES INC. All Rights Reserved.
76
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX A
CODE 39 FULL ASCII CODE TABLE
ASCII
CODE 39
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
DLE
DC1
DC2
DC3
DC4
NAK
SYN
ETB
CAN
EM
SUB
ESC
FS
GS
RS
US
SP
%U
$A
$B
$C
$D
$E
$F
$G
$H
$I
$J
$K
$L
$M
$N
$O
$P
$Q
$R
$S
$T
$U
$V
$W
$X
$Y
$Z
%A
%B
%C
%D
%E
SP
VALEU
HEXA.
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
ZEBEX INDUSTRIES INC. All Rights Reserved.
77
ASCII
CODE 39
%
&
'
(
)
*
+
,
.
/
0
1
2
3
4
5
6
7
8
9
:
;
<
=
>
?
@
A
B
C
D
E
/E
/F
/G
/H
/I
/J
/K
/L
.
/
0
1
2
3
4
5
6
7
8
9
/Z
%F
%G
%H
%I
%J
%V
A
B
C
D
E
VALEUR
HEXA.
25
26
27
28
29
2A
2B
2C
2D
2E
2F
30
31
32
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
40
41
42
43
44
45
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX A
CODE 39 FULL ASCII CODE TABLE
ASCII
CODE 39
!
"
#
$
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
[
\
]
^
_
`
a
b
c
d
/A
/B
/C
/D
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
%K
%L
%M
%N
%O
%W
+A
+B
+C
+D
VALEUR
HEXA.
21
22
23
24
4A
4B
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
ZEBEX INDUSTRIES INC. All Rights Reserved.
78
ASCII
CODE 39
F
G
H
I
e
f
g
h
i
j
k
l
m
n
o
p
q
r
s
t
u
v
w
x
y
z
{
|
}
~
DEL
F
G
H
I
+E
+F
+G
+H
+I
+J
+K
+L
+M
+N
+O
+P
+Q
+R
+S
+T
+U
+V
+W
+X
+Y
+Z
%P
%Q
%R
%S
%T
VALEUR
HEXA.
46
47
48
49
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX A
FUNCTION KEY EMULATION
FUNCTION
KEY
Ins
Del
Home
End
Up
Down
Left
Backspace
TAB
Enter(num)
Right
PgUp
Enter
PgDn
shift
5 (num)
ASCII
CODE 39
$A
$B
$C
$D
$E
$F
$G
$H
$I
$J
$K
$L
$M
$N
$O
$P
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
FUNCTION
KEY
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
ESC
Ctl(L)
Alt(L)
ZEBEX INDUSTRIES INC. All Rights Reserved.
79
ASCII
CODE 39
$Q
$R
$S
$T
$U
$V
$W
$X
$Y
$Z
%A
%B
%C
%D
%E
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
NUL
ENQ
(Up)
SOH
(Ins)
ACK
(Down)
STX
(Del)
BEL
(Left)
ETX
(Home)
BS
(Backspace)
EOT
(End)
HT
(TAB)
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
80
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
LF
(Enter)(num)
DLE
5 (num)
VT
(Right)
DC1
(F1)
FF
(PgUp)
DC2
(F2)
CR
(Enter)
DC3
(F3)
SO
(PgDn)
DC4
(F4)
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
81
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
SI
shift(L)
NAK
(F5)
SYN
(F6)
GS
(ESC)
ETB
(F7)
RS
Ctl (L)
CAN
(F8)
US
Alt (L)
EM
(F9)
SP
SUB
(F10)
!
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
82
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
ESC
(F11)
"
FS
(F12)
#
$
+
%
,
&
'
.
(
/
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
83
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
)
0
*
1
2
:
3
;
4
<
5
=
6
>
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
84
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
7
?
8
@
9
A
B
I
C
J
D
K
E
L
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
85
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
F
M
G
N
H
O
P
W
Q
X
R
Y
S
Z
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
86
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
T
[
U
\
V
]
^
e
_
f
`
g
a
h
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
87
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
b
i
c
j
d
k
l
s
m
t
n
u
o
v
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
88
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX B
CODE 39 FULL ASCII BARCODE TABLE
Start of Configuration
p
w
q
x
r
y
z
}
{
~
|
DEL
End of Configuration
ZEBEX INDUSTRIES INC. All Rights Reserved.
89
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX C
BARCODE SAMPLES
Code 39
C
O
D
E
3
9
2
8
Code 128
C O D E
1
Interleaved 2 of 5
123 456789 0
Coda bar(NW-7)
A $ 9 9 . 9 5 A
UPC A
0
44252 30245
EAN-13
4 711234 567899
ZEBEX INDUSTRIES INC. All Rights Reserved.
90
1
OUTLINE FOR PRODUCT REFERANCE MANUAL
Z-3070 CCD BARCODE SCANNER
APPENDIX D
QUICK SETTINGS
1. Quick Settings for Keyboard Wedge Mode
Program
Reset
PC/AT
End
2. Quick Settings for RS 232 Mode
Program
Reset
RS-232C
End
3. Quick Settings for German Language Keyboard
Program
German Keyboard
End
ZEBEX INDUSTRIES INC. All Rights Reserved.
91