Advantech POC-S175 User manual

POC-S175
Slim Point of Care Terminal with
17" TFT LCD monitor
User Manual
Copyright
The documentation and the software included with this product are copyrighted 2004 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of
Microsoft Corp.
All other product names or trademarks are properties of their respective
owners.
Part No. 2006S17500
Printed in Taiwan
POC-S175 User Manual
1st Edition
February 2005
ii
Product Warranty (1 years)
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1.
Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2.
Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3.
If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4.
Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for warranty service.
5.
Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.
iii
1.1 FCC Class B
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses and can radiate radio
frequency energy. If not installed and used in accordance with this
user's manual, it may cause harmful interference to radio
communications.
Note that even when this equipment is installed and used in
accordance with this user's manual, there is still no guarantee that
interference will not occur. If this equipment is believed to be causing
harmful interference to radio or television reception, this can be
determined by turning the equipment on and off. If interference is
occurring, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to a power outlet on a circuit different from that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Warning
Any changes or modifications made to the equipment
which are not expressly approved by the relevant standards authority could void your authority to operate the
equipment.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
POC-S155 User Manual
iv
1.2 Packing List
Before installing your Point of Care Terminal, ensure that the following
materials have been received:
• POC-S175 series Point of Care Terminal
• User's manual
• Accessories for POC-S175
• Y-shaped adapter for PS/2 mouse and keyboard
• Power cord (1.8 m) - USA type (UK, German types are available on
request)
• "Drivers and Utilities" CD-ROM disc
• Mounting kits and packet of screws
• External DC adapter (Manufacturer: XPiQ Inc. Model no.:
PCM80PS24)
Warning
To prevent electric shock, Do not remove cover.
No user serviceable parts inside, refer servicing to qualified personnel.
1.3 Additional Information and Assistance
1. Visit the Advantech websites at www.advantech.com or
www.advantech.com.tw where you can find the latest information
about the product.
2. Contact your distributor, sales representative, or Advantech's
customer service center for technical support if you need additional
assistance. Please have the following information ready before you
call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
v
• This equipment is a source of electromagnetic waves. Before use
please, make sure that there are not EMI sensitive devices in its surrounding which may malfunction therefore.
Warning
1. Only use the Power adapter
Manufacturer: XPiQ Inc. Model no.: PCM80PS24
Input voltage: 100-240 VAC, 47-63 Hz, 1.1-0.45 A
Output voltage: +24 VDC, 3.33 A max.
2. Use a 3 V @ 195 mA lithium battery (Model No.
BR2032)
3. Packing: please carry the unit with both hands, handle
with care
4. Our European representative:
Advantech Europe GmbH
Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel: 49-211-97477350
Fax: 49-211-97477300
5. Maintenance: to properly maintain and clean the
surfaces, use only approved products or clean with a dry
applicator
1.4 Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use
a damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping
it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
POC-S175 User Manual
vi
8. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or
electrical shock.
13. Never open the equipment. For safety reasons, the equipment
should be opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked
by service personnel:
• a. The power cord or plug is damaged.
• b. Liquid has penetrated into the equipment.
• c. The equipment has been exposed to moisture.
• d. The equipment does not work well, or you cannot get it to work
according to the user's manual.
• e. The equipment has been dropped and damaged.
• f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY
DAMAGE THE EQUIPMENT.
16. If your computer is losing dramatic time or the BIOS configuration
reset to default, the battery has no power.
Caution
1. Do not replace battery yourself. Please contact a qualified technician or your retail.
2 .The computer is provided with a battery-powered realtime clock circuit. There is a danger of explosion if battery
is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard
used batteries according to the manufacturer’s instructions
vii
17. IMPROPER INSTALLATION OF VESA MOUNTING CAN RESULT
IN SERIOUS PERSONAL INJURY! VESA mount installation should be
operated by professional technician, please contact the service
technician or your retail if you need this service.
18. CLASSIFICATION:
• Supply class I adapter
• No applied part
• IPX0
• Continuous Operation
• Not AP or APG category
19. Disconnect device: Appliance inlet.
20. Follow the national requirement to dispose unit.
21. Maintenance: to properly maintain and clean the surfaces, use only
the approved products or clean with a dry applicator.
22. Contact information:
No.1, Alley 20, Lane 26, Reuiguang Road Neihu District, Taipei,
Taiwan 114, R.O.C.
TEL: (02)27927818
23.
24. This equipment shall not be used for life support system.
25. Accessory equipment connected to the analog and digital interfaces
must be in compliance with the respective nationally harmonized IEC
standards (i.e. IEC 60950 for data processing equipment, IEC 60065 for
video equipment, IEC 61010-1 for laboratory equipment, and IEC 606011 for medical equipment.) Furthermore all configurations shall comply
with the system standard IEC 60601-1-1. Everybody who connects additional equipment to the signal input part or signal output part configures a
medical system, and is therefore, responsible that the system complies
with the requirements of the system standard IEC 60601-1-1. The unit is
POC-S175 User Manual
viii
for exclusive interconnection with IEC 60601-1 certified equipment in
the patient environment and IEC 60XXX certified equipment outside of
the patient environment. If in doubt, consult the technical services department or your local representative.
26. User not to contact SIP/SOPs and the patient at the same time.
27. The sound pressure level at the operator's position according to IEC
704-1:1982 is no more than 70dB(A).
DISCLAIMER
This set of instructions is given according to IEC
704-1. Advantech disclaims all responsibility for
the accuracy of any statements contained herein
ix
POC-S175 User Manual
x
Contents
Chapter
1 General Information ....................................... 2
1.1
1.2
Introduction ....................................................................... 2
Specifications .................................................................... 2
1.2.1
1.2.2
1.2.3
1.2.4
1.2.5
1.2.6
1.2.7
1.2.8
1.2.9
1.3
1.4
Chapter
LCD Specifications ........................................................... 5
Dimensions........................................................................ 6
Figure 1.1:Dimensions of the POC-S175 ...................... 6
2 System Setup.................................................... 8
2.1
2.2
A Quick Tour of the POC-S175........................................ 8
Figure 2.1:Front view of Point of Care Terminal .......... 8
Figure 2.2:Rear view of Point of Care Terminal ........... 9
Installation Procedures .................................................... 10
2.2.1
2.2.2
2.2.3
2.2.4
2.3
2.4
2.5
Chapter
Chapter
General ........................................................................... 2
Standard PC functions ................................................... 2
Flat panel interface ......................................................... 3
Audio function ............................................................... 3
PCI bus Ethernet interface ............................................. 3
Touchscreen (Optional) ................................................. 4
Table 1.1: ..................................................................... 4
Table 1.2:Table 1.1:Touhscreen specification ............... 4
Optional modules ........................................................... 4
Environment ................................................................... 4
Cleaning/Disinfecting .................................................... 5
Connecting the power cord .......................................... 10
Figure 2.3:Connecting the power cord ........................ 10
Connecting the keyboard and mouse ........................... 11
Figure 2.4:Connecting the mouse and keyboard ......... 11
Switch on the power .................................................... 11
Connecting the COM ports (COM 1,2) ....................... 11
Figure 2.5:Connecting the device to COM ports
.. 11
Running the BIOS Setup Program .................................. 12
Installing System Software.............................................. 12
Installing the Drivers....................................................... 13
Figure 2.6:File dir "Drivers and Utilities" of CD ........ 13
3 PCI BUS Ethernet Interface ........................ 16
3.1
3.2
Introduction ..................................................................... 16
nstallation of Ethernet Driver.......................................... 16
3.3
Further information ......................................................... 18
3.2.1
Installation for Windows 2000/XP .............................. 16
Figure 3.1:Lan Driver Installation ............................... 17
4 PCI Graphic Setup........................................ 20
4.1
Introduction ..................................................................... 20
4.1.1
Chipset ......................................................................... 20
xi
Table of Contents
4.1.2
4.1.3
4.2
4.3
Chapter
Chapter
Display memory ........................................................... 20
Display types ................................................................ 20
Installation of PCI Graphic Driver .................................. 20
4.2.1
Installation for Windows 2000/XP .............................. 22
Figure 4.1:Graphic Driver Installation ......................... 22
Further information ......................................................... 23
5 Audio Interface.............................................. 26
5.1
5.2
Introduction ..................................................................... 26
Installation of Audio Driver ............................................ 26
5.3
Further information ......................................................... 28
5.2.1
Installation for Windows 2000/XP .............................. 27
Figure 5.1:Audio Driver Installation ........................... 27
6 Touchscreen Interface .................................. 30
6.1
6.2
Introduction ..................................................................... 30
6.1.1
6.1.2
6.1.3
Installation of Driver for Touchscreen ............................ 31
6.2.1
6.2.2
6.3
General Information ..................................................... 30
General specifications .................................................. 30
Environmental specifications ....................................... 30
Installation for Windows 2000 .................................... 32
Figure 6.1:Win2000 Driver Installation ....................... 32
Installation for Windows XP ....................................... 33
Figure 6.2:WinXP Driver Installation ......................... 33
Further information ......................................................... 34
Appendix A VESA Mounting ............................................ 36
A.1
Install VESA Mounting ................................................. 36
POC-S175 User Manual
Figure A.1:VESA mounting 75x75mm, 100x100 mm 37
xii
CHAPTER
1
2
General Information
This section provides general information and technical specifications about
the POC-S175
Sections include:
• Introduction
• Specifications
• LCD Specifications
• Dimentions
Chapter 1 General Information
1.1 Introduction
The POC-S175 is a multimedia Pentium® Mobility processor-based
computer that is designed to serve as a Point of Care terminal (POC.) It is
a PC-based system with 17" color TFT LCD display, on-board PCI Ethernet controller, dual COM port interfaces and a 16-bit stereo audio controller. With a built-in 2.5” HDD drive, and CF card sockets, the POC-S175
is as slim and user-friendly as a notebook computer and low audible
noise. For system integrators, this silent, compact, mobility and highly
integrated multimedia system lets you easily build a Point of Care Terminal into your applications. Common industrial applications include factory automation systems, precision machinery, and production process
control. It is also suitable for many non-industrial applications, including
interactive kiosk systems, entertainment management, and car park automation. The POC-S175 is a reliable solution to your application's processing requirements.
1.2 Specifications
1.2.1 General
• Dimensions (W x H x D): 436.5 x 376.5 x 83.6 mm (17.18” x 14.82” x
3.28”)
• Weight: 6.4kg ( 14.1 lb )
• Power supply: DC model: 80 watts max
• External DC Adapter: (Manufacturer: XPiQ Inc. Model no.:
PCM80PS24) used within POC-S175XXXXXXXX
• Input voltage: 100-240 VAC, 47-63 Hz, 1.1-0.45 A
• Output voltage: +24 VDC, 3.33 A max.
• Disk drive housing: Space for one 2.5" HDD
• Front panel: IP65/NEMA compliant
• Whole System: IPX0 compliant
1.2.2 Standard PC functions
• CPU: Intel® Embedded Intel® Pentium® M or Celeron® M processor
w/64KB primary cache memory
POC-S175User Manual
2
• Memory: 1 x 200 pin SO-DIMM sockets, support ECC Double DataRate (DDR)128 MB to 512 MB, accept 128/256/512 MB DDR200/
266DRAM (855GME could support to DDR333 DRAM)
• System chipset: Intel 855GME or 852GM GMCH/ ICH4 Chipset 400
MHz PSB
• BIOS: Award 256 KB Flash BIOS, supports Plug & Play, APM
• Serial ports: Two RS-232 ports with optical isolation. All ports are
compatible with 16C550 UARTs
• Universal serial bus (USB) port: Supports up to two USB ports
• Watchdog timer: 62-level, interval 1 ~ 62 seconds. Automatically generates system reset or IRQ11 when the system stops due to a program
error or EMI.
• CMOS Battery (BIOS): 3.0 V @ 195 mA lithium battery
1.2.3 Flat panel interface
• Chipset: Intel 855GME or 852GM
• Memory Size: Optimized shared memory architecture, supports 32MB
frame buffer using system memory
• Display type: Simultaneously supports flat panel displays (EL, LCD
and gas plasma)
• Display resolution: Supports TFT LCD displays up to 1280 x 1024 @
16 M colors
1.2.4 Audio function
• Chipset: Realtek ALC202
• Audio controller: 16-bit codec, Full-Duplex stereo single-chip PCI
audio solution
• Speaker: Full alarm volume > 70 dB(A) 1 meter
• Stereo sound: 100% DOS GAME compatible (Sound Blaster or Sound
Blaster Pro)
• Audio interface: Microphone-in, Line-out.
1.2.5 PCI bus Ethernet interface
• Ethernet interface: Full compliance with IEEE 802.3u 100Base-T and
10 Base-T specifications. Includes software drivers and boot ROM
• 100/10Base-T auto-sensing capability
3
Chapter 1
1.2.6 Touchscreen (Optional)
Table 1.1:
Type
Analog Resistive
Resolution
Continuous
Light Transmission
75%
Controller
RS-232 interface (uses COM4)
Power Consumption
+5V@200 mA
Software Driver
Supports Windows 2000,Windows XP
Durability (touches in a lifetime)
30 million
Table 1.2: Table 1.1:Touhscreen specification
Note
The Point of Care Terminal with the optionally installed
touchscreen will share COM4. Once the touchscreen is
installed, COM4 cannot be used for other purposes.
1.2.7 Optional modules
• Memory: 128/256/512 MB DDR200/266 DRAM
• HDD: 2.5" HDD
• Touchscreen: Analog resistive
1.2.8 Environment
• Temperature: 0 ~ 40° C (32 ~ 104° F)
• Relative humidity: 10° C to 40° C / 20% RH to 90% RH operating 20° C to 50° C/ 10% RH to 95% RH Storage ( Non-condensing )
• Shock: 20 G, half sine, 11 msec duration
• Vibration: 0.047 double amplitude displacement ( 5 ~ 32 Hz) 1G Peak
(32 -500 Hz )
• Power MTBF: 100,000 hrs
• Altitudes: Operational : 6,000 feet ; shipping : 40,000 feet
• Certifications: EMC: CE, FCC approved
• Safety: UL60601-1 and EN60601-1 approved.
POC-S175User Manual
4
• This device bears the CE label in accordance with the provisions of the
EMC Directive 89/336/EMC and the Low Voltage Directive 73/23/
EEC.
1.2.9 Cleaning/Disinfecting
During normal use of the POC-S175 may become soiled and should,
therefore, be cleaned regularly. Agents: Green tinctured soap and Enzymatic detergents
Steps:
1. Wipe the POC-S175 with a clean cloth that has been moistened in the
cleaning solution.
2. Prepare agent per manufacturer’s instructions or hospital protocol.
3. Wipe thoroughly with a clean cloth
Cautions
Do not immerse or rinse the POC-S175 and its peripherals. If you accidentally spill liquid on the device, disconnect the unit from the power source. Contact your
Biomed regarding the continued safety of the unit
before placing it back in operation.
Do not spray cleaning agent on the chassis.
Do not use disinfectants that contain phenol. Do not
autoclave or clean the POC-S175 or its peripherals
with strong aromatic, chlorinated, ketone, ether, or
Esther
solvents, sharp tools or abrasives. Never immerse
electrical connectors in water or other liquids.
1.3 LCD Specifications
• Display type: 17" TFT LCD.
• Resolution: 1280 x 1024
• Colors: 16.7M (8 bits/color)
• Dot size (mm): 0.264 x 0.264
• Viewing angle: 170°
• Luminance: 250 cd/m2
• Contrast ratio: 500 : 1
5
Chapter 1
• LCD MTBF: 50,000 hours
• Backlight lifetime: 50,000 hours (typical)
1.4 Dimensions
Figure 1.1: Dimensions of the POC-S175
POC-S175User Manual
6
CHAPTER
2
2
System Setup
This section gives a quick tour of the
POC-S175 including installation procedures, BIOS Setup, and software and
driver installation
Chapter 2 System Setup
2.1 A Quick Tour of the POC-S175
Before you start to set up the POC-S175, take a moment to become familiar with the locations and purposes of the controls, drives, connections
and ports, which are illustrated in the figures below.
When you place the POC-S175 upright on the desktop, its front panel
appears as shown in Figure 2-1
.
Figure 2.1: Front view of Point of Care Terminal
POC-S175 User Manual
8
When you turn the Point of Care Terminal around and look at its rear
cover, the sunken I/O section is at the bottom of the panel PC, as shown in
Figure 2-2. (The I/O section includes various I/O ports, including serial
ports, VGA port, the Ethernet port, USB ports, the microphone jack, and
so on.)
Figure 2.2: Rear view of Point of Care Terminal
9
Chapter 2
2.2 Installation Procedures
2.2.1 Connecting the power cord
The POC-S175 could only be powered by a DC power adapter (XPiQ
Model no.PCM80PS24). Be sure to always handle the power cords by
holding the plug ends only.
Follow these procedures in order:
1. Connect the female end of the power adapter to the DC jack of the
panel PC. (See Figure 2-3.)
2. Connect the female end of the power cord to the DC power adapter
3. Connect the 3-pin male plug of the power cord to an electrical outlet.
Figure 2.3: Connecting the power cord
3. After finish all above installation, please jump to section 2.2.2 and continue your installation procedure
POC-S175 User Manual
10
2.2.2 Connecting the keyboard and mouse
1. Connect the Y-shaped adapter to the PS/2 mouse and keyboard port on
the I/O section of the POC-S175. (See Figure 2-4.)
2. Connect the PS/2 mouse and keyboard to the Y-shaped adapter. (See
Figure 2-4.)
Figure 2.4: Connecting the mouse and keyboard
2.2.3 Switch on the power
Switch on the reset switch on the rear cover. (See Figure 2-5.)
2.2.4 Connecting the COM ports (COM 1,2)
Figure 2.5: Connecting the device to COM ports
11
Chapter 2
2.3 Running the BIOS Setup Program
Your POC-S175 is likely to have been properly set up and configured by
your dealer prior to delivery. You may still find it necessary to use the
BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of
hard drive. The setup program is stored in read-only memory. It can be
accessed either when you turn on or reset the panel PC, by pressing the "
Crtl+Alt+Del " key on your keyboard immediately after powering on the
computer.
The settings you specify with the setup program are recorded in a special
area of memory called CMOS RAM. This memory is backed up by a battery so that it will not be erased when you turn off or reset the system.
Whenever you turn on the power, the system reads the settings stored in
CMOS RAM and compares them to the equipment check conducted during the power on self-test (POST). If an error occurs, an error message
will be displayed on screen, and you will be prompted to run the setup
program.
2.4 Installing System Software
Recent releases of operating systems from major vendors include setup
programs which load automatically and guide you through hard disk
preparation and operating system installation. The guidelines below will
help you determine the steps necessary to install your operating system
on the panel PC hard drive.
Note
Some distributors and system integrators may have
already pre-installed system software prior to shipment of
your panel PC.
If required, insert your operating system's installation or setup diskette
into the external diskette drive until the release button pops out.
The BIOS supports system boot-up directly from the CD-ROM drive.
You may also insert your system installation CD-ROM disk into your
external CD-ROM drive.
Power on or reset the system by pressing the "Ctrl"+"Alt"+"Del" keys
simultaneously. The Point of Care Terminal will automatically load the
operating system from the diskette or CD-ROM.
POC-S175 User Manual
12
If you are presented with the opening screen of a setup or installation program, follow the instructions on screen. The setup program will guide
you through preparation of your hard drive, and installation of the operating system.
2.5 Installing the Drivers
After installing your system software, you will be able to set up the Ethernet, VGA, audio and touchscreen functions by your own external CDROM drive. All the drivers except the CD-ROM drive driver are stored in
a CD-ROM disc entitled "Drivers and Utilities."
The standard procedures for installing the Ethernet, VGA, audio, and
touchscreen drivers are described in Chapters 3, 4, 5, and 6 respectively.
The utility directory includes multimedia programs. Refer to the
README.TXT file inside the VGA folders for more detailed information.
The various drivers and utilities in the CD-ROM disc have their own text
files which help users install the drivers and understand their functions.
These files are a very useful supplement to the information in this manual.
For your reference, the directory of drivers on the "Drivers and Utilities"
CD-ROM is:
Figure 2.6: File dir "Drivers and Utilities" of CD
Note
The drivers and utilities used for the POC-S175 panel PCs
are subject to change without notice. If in doubt, check
Advantech's website or contact our application
engineers for the latest information regarding drivers and
utilities.
13
Chapter 2
POC-S175 User Manual
14
3
CHAPTER
2
PCI Bus Ethernet Interface
This section includs information about
the high-performance Ethernet network
chipset
Chapter 3 PCI BUS Ethernet Interface
3.1 Introduction
The POC-S175 is equipped with a high-performance 32-bit Ethernet
chipset which is fully compliant with IEEE 802.3 100 Mbps CSMA/CD
standards. It is supported by major network operating systems. It is also
both 100Base-T and 10Base-T compatible.
3.2 nstallation of Ethernet Driver
3.2.1 Installation for Windows 2000/XP
Complete the following steps to install the LAN driver. Follow the procedures in the flow chart that apply to the operating system that you are
using within your POC-S175.
Important
The following windows illustrations are examples only.
You must follow the flow chart instructions and pay
attention to the instructions which appear on your
screen.
Note1
The external CD-ROM drive is designated as “D” throughout this chapter.
Note2
<Enter> means pressing the “Enter” key on the keyboard.
POC-S175 User Manual
16
Figure 3.1: Lan Driver Installation
17
Chapter 3
3.3 Further information
For further information about the Ethernet installation in your POCS175, included Driver updates, troubleshooting guides and FAQ lists
please visit the following web resources.
Realtek website: www.intel.com.tw
Advantech websites: www.advantech.com
www.advantech.com.tw
POC-S175 User Manual
18
4
CHAPTER
2
PCI Graphic Setup
This section describes the PCI Graphics
card setup and driver installation.
Chapter 4 PCI Graphic Setup
4.1 Introduction
The POC-S175 has an onboard PCI/AGP flat panel interface. The specifications and features are described as follows:
4.1.1 Chipset
The POC-S175 uses a Intel 855GME/852GM for its graphic controller. It
supports LVDS LCD displays, and CRT monitors.
4.1.2 Display memory
The 855GME chip, the VGA controller can drive CRT displays up to
1600 x 1200 at 85-Hz and 2048 x 1536 at 75-Hz, color panel displays in
LVDS model with resolutions up to UXGA panel resolution with frequency range from 25 MHz to 112 MHz.
The 852GM chip , the VGA controller can drive CRT displays up to 1600
x 1200 at 85-Hz and 1920 x 1440 at 60-Hz, color panel displays in LVDS
model with resolutions up to 1400 X 1050 at 75- Hz.
4.1.3 Display types
CRT and panel displays can be used simultaneously. The POC-S175 can
be set in one of three configurations: CRT only, LVDS only, both CRT
and LFP (LVDS). The system is initially set to simultaneous display
mode - CRT and LFP (LDVS).
4.2 Installation of PCI Graphic Driver
Complete the following steps to install the SVGA driver. Follow the
procedures in the flow chart that apply to the operating system that you
are using within your POC-S175.
Important
Note1
The following windows illustrations are examples only.
You must follow the flow chart instructions and pay
attention to the instructions which appear on your
screen.
The CD-ROM drive is designated as “D” throughout this
chapter.
POC-S175User Manual
20
Note2
<Enter> means pressing the “Enter” key on the keyboard.
Note3
Before you install the graphic driver of POC-S175, please
ensure you have installed the INF driver of the Intel
855GME/852GM chipset. You can find this driver in the
Utility CD-ROM.
21
Chapter 4
4.2.1 Installation for Windows 2000/XP
Figure 4.1: Graphic Driver Installation
POC-S175User Manual
22
4.3 Further information
For further information about the AGP/SVGA installation in your POCS175, included Driver updates, troubleshooting guides and FAQ lists
please visit the following web resources.
Intel website: www.intel.com.tw
Advantech websites: www.advantech.com
www.advantech.com.tw
23
Chapter 4
POC-S175User Manual
24
CHAPTER
5
2
Audio Interface
This section explains the audio interface of the POC-S175 and installation
of the Windows 2000/XP drivers
Chapter 5 Audio Interface
5.1 Introduction
The POC-S175's onboard audio interface provides high-quality stereo
sound and FM music synthesis (ESFM) by using the ALC202 audio
controller from Realtek. The audio interface can record, compress, and
play back voice, sound, and music with a built-in mixer control. The
POC-S175's onboard audio interface also supports the Plug and Play
(PnP) standard and provides PnP configuration for audio, FM, and
MPU-104 logical devices. It is compatible with Sound Blaster, Sound
Blaster Pro version 3.01, voice, and music functions. The ESFM
synthesizer is register compatible with the OPL3 and has extended
capabilities.
5.2 Installation of Audio Driver
Before installing the audio driver, please take note of the procedures
detailed below. You must know which operating system you are using
in your POC-S175, and then refer to the corresponding installation flow
chart. Just follow the steps in the flow chart. You can quickly and
successfully complete the installation, even though you are not familiar
with instructions for Windows.
Important
The following windows illustrations are examples only.
You must follow the flow chart instructions and pay
attention to the instructions which appear on your
screen.
Note1
The external CD-ROM drive is designated as “D” throughout this chapter.
Note2
<Enter> means pressing the “Enter” key on the keyboard.
POC-S175 User Manual
26
5.2.1 Installation for Windows 2000/XP
Figure 5.1: Audio Driver Installation
27
Chapter 5
5.3 Further information
For further information about the Audio interface installation in your
POC-S175, included Driver updates, troubleshooting guides and FAQ
lists please visit the following web resources.
Realtek website: www.realtek.com.tw
Advantech websites: www.advantech.com
www.advantech.com.tw
POC-S175 User Manual
28
6
CHAPTER
2
Touchscreen Interface
This section explains the Touchscreen
Interface including its specifications,
operating conditions, and driver installation for Windows 2000/XP
Chapter 6 Touchscreen Interface
6.1 Introduction
6.1.1 General Information
The POC-S175's optional touchscreen incorporates advanced secondgeneration 5-wire resistive technology. They allow 75% light
transmission respectively. The resistive and capacitive models have an
antiglare surface. All models provide greatly enhanced visual
resolution. They also have new improved scratch-resistant features.
The touchscreen is manufactured from UL-recognized components.
When properly installed, the touchscreen's ball impact resistance
meets the UL 1950 standard. Its fire resistance meets the UL-746C, 19
mm (0.75") flame test standard. Systems incorporating the
touchscreen, controllers, and cables have been approved to FCC
Class B standards.
6.1.2 General specifications
Please refer to Chapter 1, Section 1.2 of this manual.
6.1.3 Environmental specifications
Temperature:
0° ~ 40° C (operating)
-20° ~ 60° C (storage)
Relative humidity:
90 RH at 35° C (operating)
90 RH at 35° C for 240 hours, non-condensing (storage)
Chemical resistance: The active area of the touchscreen is resistant
to the following chemicals when exposed for a period of one hour at a
temperature of 21° C (71° F):
• Acetone
• Methylene chloride
• Methyl ethyl ketone
• Isopropyl alcohol
• Hexane
• Ammonia-based glass cleaners
POC-S175 User Manual
30
• Turpentine
• Mineral spirits
• Foods and beverages
6.2 Installation of Driver for Touchscreen
To facilitate installation of the touchscreen driver, you should read the
instructions in this section carefully before you attempt installation.
Important
The following windows illustrations are examples only.
You must follow the flow chart instructions and pay
attention to the instructions which appear on your
screen.
Note1
The external CD-ROM drive is designated as “D” throughout this chapter.
Note2
<Enter> means pressing the “Enter” key on the keyboard.
31
Chapter 6
6.2.1 Installation for Windows 2000
Figure 6.1: Win2000 Driver Installation
POC-S175 User Manual
32
6.2.2 Installation for Windows XP
Figure 6.2: WinXP Driver Installation
33
Chapter 6
6.3 Further information
For further information about the Touchscreen installation in your POCS175, included Driver updates, troubleshooting guides and FAQ lists
please visit the following web resources.
Elo website: www.elotouch.com
Advantech websites: www.advantech.com
www.advantech.com.tw
POC-S175 User Manual
34
A
APPENDIX
2
VESA Mounting
The following section explains how to
install the VESA mounting system for
the POC-S175
Appendix A VESA Mounting
A.1 Install VESA Mounting
The POC-S175 also provides standard VESA mounting to help system
integrators conveniently integrate the panel PC into their system.
Never use the mounting brackets except for providing by Advantech to
prevent the unreliable fixing of POC-S175. VESA mount installation
should be operated by professional technician, please contact the service
technician or your retail if you need this service.
Installation instructions follow:
1. The wall-mounting attachment is comprised of two parts: one back
bracket, and one mounting bracket.
2. First attach the back bracket to the rear cover of the POC-S175, securing it in place with four of the philips-head screws provided.
3. Mount the mounting bracket on the wall or other flat surface. The back
bracket slides vertically from the top into the mounting bracket. It can be
secured to the mounting bracket by screwing four of the philips-head
screws provided through the corresponding holes at the tops of the
mounting bracket.
Warning
Be sure to secure the screws of the mounting bracket
tightly. Loose jointed between POC-S175 and mounting
bracket could be damaged to human life.
POC-S175 User’s Manual
36
Figure A.1: VESA mounting 75x75mm, 100x100mm
37
Appendix A
POC-S175 User’s Manual
38