ECX Ruckus ECX03003 Instruction manual

RUCKUS
TM
1/10 ELECTRIC MONSTER TRUCK
ECX2000 | ECX2000AU | ECX2000EU | ECX2000UK
ECX2100 | ECX2100AU | ECX2100EU | ECX2100UK
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUEL D’UTILISATION
MANUALE
Congratulations on your purchase of the Electrix
RCTM RuckusTM Monster Truck.
This 1/10 scale model introduces you to the sport
of RC driving.
Herzlichen Glückwunsch zum Kauf des Electrix
RCTM RuckusTM Monster Truck. Dieses 1/10 Scale
Model öffnet Ihnen die Welt des RC Car Sports.
Nous vous félicitons pour l’achat du Electrix RCTM
RuckusTM Monster Truck. Ce modèle 1/10 vous
introduit au sport de la conduite RC.
Congratulazioni per l’acquisto di questo RC
Ruckus Monster Truck Electrix. Questa vettura in
scala 1/10 vi introdurrà nel mondo dei modelli RC.
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc. For up-to-date
product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language:
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR
create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before
operating. Failure to operate the product correctly can result in damage to the product, personal property and cause
serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and
requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result
in injury or damage to the product or other property. Do not attempt disassembly, use with incompatible components
or augment product in any way without the approval of Horizon Hobby, Inc. This manual contains instructions for
safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual,
prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in
a manner that does not endanger yourself and others or result in
damage to the product or the property of others.
This model is controlled by a radio signal subject to interference
from many sources outside your control. This interference can cause
momentary loss of control so it is advisable to always keep a safe
distance in all directions around your model, as this margin will help
avoid collisions or injury.
Age Recommendation: Not for children under 14 years. This is
not a toy.
• Never operate your model with low transmitter batteries.
• Always operate your model in an open area away from cars, traffic
or people.
• Never operate the model in the street or in populated areas for
any reason.
• Carefully follow the directions and warnings for this and any
optional support equipment (chargers, rechargeable battery packs,
etc.) you use.
• Keep all chemicals, small parts and anything electrical out of the
reach of children.
• Moisture causes damage to electronics. Avoid water exposure to
all equipment not specifically designed and protected for
this purpose.
• Never lick or place any portion of your model in your mouth as it
could cause serious injury or even death.
• First-time builders should seek advice from people with building
experience to operate the model correctly and meet its
performance potential.
• Exercise caution when using tools and sharp instruments.
• Take care when building, as some parts may have sharp edges.
• Immediately after using your model, do NOT touch equipment on
the model such as the motor, electronic speed control and battery,
because they generate high temperatures. You may burn yourself
seriously touching them.
• Do not put fingers or any objects inside rotating and moving parts,
as this may cause damage or serious injury.
• Be sure that your operating frequency is clear before turning on or
running your model, and never share the same frequency with
somebody else at the same time.
• Ensure that others are aware of the operating frequency you are
using and when you are using it.
• Always turn on your transmitter before you turn on the receiver
in the car. Always turn off the receiver before turning your
transmitter off.
• Keep the wheels of the model off the ground when checking the
operation of the radio equipment.
TABLE OF CONTENTS
Safety Precautions and Warnings .......................................................2
Finishing ...............................................................................................7
Specifications .......................................................................................3
Setting the Gear Mesh.........................................................................8
Components .........................................................................................3
Electronic Speed Control (ESC) ............................................................8
Vehicle Preparations
Electrical Layout ...................................................................................8
Installing Antenna Tube and Body .......................................................3
Wheel Assembly ..................................................................................8
Installing Transmitter Battery .............................................................4
Maintenance ........................................................................................9
Installing Transmitter Antenna ............................................................4
Shock Cleaning.....................................................................................9
Charging the Battery ............................................................................4
Fasteners ..............................................................................................9
Installing Vehicle Battery .....................................................................5
Troubleshooting Guide ........................................................................10
Operation
Warranty Information..........................................................................10
Transmitter controls .............................................................................6
Contact Information ............................................................................11
Getting Started.....................................................................................7
FCC and Compliance Information for the European Union .................11
2
RUCKUS
EN
SPECIFICATIONS
Receiver
Transmitter
Frequency
Modulation
Battery
Current Consumption
Size
Weight
27MHz
Pulse Proportional Modulation (PPM)
AA x 8
200mAh
17 x 23.5 x 7.5mm
382 g
Servo
Power Supply
Output Torque
Operating Speed
Size
Frequency
Intermediate Frequency
Current Consumption
Weight
27MHz
445kHz
18mAh
15 g
Electronic Speed Control (ESC)
Input Voltage
Electric Capacity (FET)
Electric Capacity (FET)
PWM Frequency
BEC Voltage
Size
Weight
4.8V~6V (shared with receiver)
41.66 oz (3 kg-cm)
0.23sec/60 degrees of travel
40.5 x 20 x 36.8mm
7.2–8.4V
Forward 80 A/240 A
Reverse 60 A/160 A
1kHz
5 V/1 A
27 x 35 x 17.3mm
34 g - 36 g
COMPONENTS
TM
TM
1. Electrix RC Ruckus 1/10 Monster Truck
2. Transmitter
3. Antenna Tube (ECX1066)
1
2
3
Included Items
4. AA (8)
5. ECX1075 Battery Charger
ECX1075AU Battery Charger (AU)
ECX1075EU Battery Charger (EU)
ECX1075UK Battery Charger (UK)
4
5
6
Note: Charger power outlet terminals
not shown.
6. 7.2V NiMH battery (DYN1050)
7. Alternate Crystal Set (not shown)
VEHICLE PREPARATIONS
1
INSTALLING ANTENNA TUBE AND BODY
1. Body Clips (ECX1048)
2. Antenna Tube (ECX1087)
2
1
RUCKUS
3
EN
INSTALLING TRANSMITTER BATTERIES
1. Slide panel open on bottom of transmitter.
2. Obey battery plus (+) and minus (-) diagram in transmitter to install
8 AA batteries.
3. Slide panel closed on transmitter.
WARNING: ALWAYS use fully charged batteries in the
transmitter. Low battery power can result in loss of control of
the RC vehicle.
NEVER install damaged batteries, batteries of mixed types or batteries
of different ages in the transmitter. Remove exhausted batteries.
NEVER store transmitter with batteries installed.
Note: Optional AA NiMH battery charger DYN1970 is available. Use
only batteries approved for use with that charger. DYN1970 2300mAh
Tx NiMH Conversion Kit: FUT, ECX
1
2
3
Note: Alkaline AA size batteries are recommended.
INSTALLING TRANSMITTER
ANTENNA
1. Put antenna in hole in top of the transmitter.
2. The collapsed antenna will be 2-1/4 inches
long when fully inserted.
3. Turn the antenna clockwise until it is tight.
1
2-1/4 in
(57mm)
2
3
CHARGING THE BATTERY
A. Attach battery connector to the
charger correctly.
B. 7.2V NiMH battery
C. Compatible Battery Charger
Note: Charger power outlet terminals
not shown.
A
Never leave
Always charge
Never charge
Never charge
Batteries outside
Batteries away from charging Batteries
damaged Batteries.
recommended levels.
flammable materials.
unattended.
C
B
Note: The vehicle battery charger produces 300 milliAmps per
hour. Divide the mAh capacity on the label of a battery by 300
to know how long battery charging will require. For example, an
1800mAh battery requires 6 hours to charge.
• Read all safety precautions and literature prior to use of
this product.
• Never allow minors to charge battery packs without adult
supervision.
• Never attempt to charge dead or damaged batteries.
• Never charge a battery if the cable has been pinched or shorted.
4
RUCKUS
• Never allow batteries or charger to come into contact with
moisture at any time.
• Never charge batteries in extremely hot or cold places
(recommended between 50–80 degrees Fahrenheit) or place in
direct sunlight.
• Always use only NiMH rechargeable batteries. This charger cannot
charge batteries such as “heavy duty,” “alkaline battery,” or
“mercury battery.”
• Always connect the positive red lead (+) and negative black lead
(-) terminals of the battery to the charger terminals correctly.
• Always disconnect the battery and charger after charging, and let
them cool between charges.
• Always inspect the battery before charging.
• Always terminate all processes and contact Horizon Hobby if the
product malfunctions.
• Always make sure you know the specifications of the battery to
be charged or discharged to ensure it meets the requirements of
this charger.
• Never connect more than one battery pack to this charger at a time.
• Always constantly monitor the temperature of the battery pack
while charging.
• Always end the charging process if the charger or battery becomes
hot to the touch or starts to change form during the charge process.
EN
INSTALLING VEHICLE BATTERY
• Turn the thumb nuts on the chassis to remove the battery strap
holding the battery. Remove or install a battery and replace the
battery strap, locking the strap in place by turning the thumb nuts.
• You can put the foam blocks (ECX2015) in front of the battery so
the weight of the battery increases rear traction or in back of the
battery to increase steering response.
OPERATION
ALWAYS turn on your transmitter before you turn on the receiver in the
car. Always turn off the receiver before turning your transmitter off.
WARNING
ALWAYS operate vehicle in a wide open area. Operating the vehicle
in a small space or indoors can cause overheating at low speeds.
Operating at low speed makes heat in the electronic speed control
(ESC). Overheating can damage the vehicle and failure may result.
MOTOR CARE
• Seat motor brushes by driving smoothly on a flat surface during
use of the first battery charge.
Always keep
vehicle in sight
and under control.
• Prolong motor life by preventing overheat conditions. Undue
motor wear results from frequent turns, stops and starts,
pushing objects, driving in deep sand and tall grass and driving
continuously up hill.
• Over-temperature protection is installed on the ESC to prevent
circuit damage, but cannot protect the motor from driving
against heavy resistance.
RUCKUS
5
EN
TRANSMITTER CONTROLS
AM 27MHZ TRANSMITTER CRYSTAL
REVERSE SWITCH
ANTENNA
Pull antenna out to its
full length
(ECX1067 Antenna Only)
Part #
ECX1081
ECX1082
ECX1083
ECX1084
ECX1085
ECX1086
Description
Crystal Set 1 26.995
Crystal Set 2 27.045
Crystal Set 3 27.095
Crystal Set 4 27.145
Crystal Set 5 27.195
Crystal Set 6 27.255
AM Transmitter Crystal
(Tx)
AM Receiver Crystal
(Rx)
AM Rx
AM Tx
Note: Paired AM crystals must
be replaced to change control
frequencies. Do NOT use FM Crystals.
Allows you to change the
direction of steering (ST. REV)
and throttle (TH. REV) controls.
(Default settings are “N”)
STEERING TRIM
ST. D/R
Adjust to make the vehicle
drive straight with no input
at the steering wheel
Adjusts the amount the front wheels
move when turned left or right
(Steering Dual Rate)
THROTTLE TRIM
POWER SWITCH
Adjusts the neutral point of
the electronic speed control
Power on
or off the
transmitter
STEERING WHEEL
BATTERY LEVEL INDICATOR
Control steering. Right and
Left steering with ST. REV
Switch on N (See ST. REV
switch)
Good battery power
Low battery power
Note: Red light will flash with an
audible signal (beep) when batteries
are low
THROTTLE TRIGGER
CHARGER PORT
Read instructions before charging.
Charge only rechargeable batteries. Non-rechargeable batteries
may burst causing injury to persons
and/or damage to property.
Note: The center pin on the charge jack is positive.
6
RUCKUS
Forward (when Stop
TH. REV switch
on N)
Reverse
(when TH.
REV switch
on N)
Controls power to motor for forward
or reverse (See TH. REV switch)
EN
GETTING STARTED
1. Fully extend Antenna and Power on Transmitter.
2. Connect battery (page 3) to Electronic Speed Control (ESC) and
power on the ESC.
3. Do a Test of Transmitter’s control of vehicle with vehicle wheels
off ground.
4. Start driving slowly and if the vehicle does not go straight, adjust
steering trim dial on Transmitter.
Note: Seat motor brushes by driving smoothly on a flat surface
during use of the first battery charge.
WHEN YOU ARE FINISHED
1. Power off Electronic Speed Control (ESC)
3. Disconnect Battery
1
2
2. Power off the Transmitter and Lower Antenna
4. Remove Battery from vehicle
Note: To prevent damage to antenna, collapse the antenna by pulling
the lower sections in first.
RUCKUS
7
EN
SETTING THE GEAR MESH
Gear mesh has already been set at the factory, and setting it is only
necessary when changing motors or gears.
Note: You must remove the vehicle’s gear cover (A) to do this
adjustment.
Proper gear mesh (how gear teeth meet) is important to the
performance of the vehicle. When gear mesh is too loose, the spur
gear could be damaged by the pinion gear of the motor. If the mesh is
too tight, speed could be limited and the motor and ESC will overheat.
A
1. Loosen the two (2) motor screws.
2. Put a small piece of paper between the pinion and spur gears.
3. Push the gears together while tightening the motor screws.
4. Remove the paper and the gears should move a small amount.
5. Reinstall gear cover.
ELECTRONIC SPEED CONTROL (ESC)
Note: When motor disconnected or damaged, beep may not
be heard.
Note: Low voltage cutoff (LVC) will stop the vehicle when the battery
gets low. The ESC will reset after approximately 10 seconds. The
vehicle can then be driven slowly back to the driver for
battery recharge.
LED
beep
beep beep
beep beep beep
LED Status Description
beep
LED Indication
Solid Green
Forward
Solid Red
Reverse
Red LEDs flashing with beep
Transmitter is not being
received.
Red LEDs flashing twice with beeps
Signal that Vehicle
battery is low.
Red LEDs flashing three times with
beeps
Motor is overloaded or
temperature of ESC
is high.
beep
beep beep
beep beep beep
beep beep
beep beep beep
ELECTRICAL LAYOUT
E
Part # Description
A
ECX1071
B
DYN1050 Battery 7.2V
C
ECX1069
D
ECX1068
Receiver
E
ECX1070
Electronic Speed Control
(ESC)
Motor
Steering Servo
F
Channel 1
G
Channel 2
H
AM Receiver Crystal (Rx)
Note: For correct operation, Channels
1 and 2 must be used as shown in
wiring diagram.
The motor can be disconnected from
the ESC at the connectors in the wiring.
8
A
Motor RUCKUS
B
Battery 7.2V
AM Rx
H
G
C
Receiver
Steering Servo
D
F
EN
MAINTENANCE
SHOCK CLEANING
REAR SHOCK
ECX1037
• Oil-filled shocks will require regular maintenance due to the oil
breaking down or getting dirty. This maintenance should be
performed after about every 3 to 5 hours of use depending on
conditions that the vehicle is used in.
• Remove the shock from the vehicle.
• Remove the cap from the shock body and dispose of fluid.
• Disassemble the shock. Clean thoroughly with DYN5505. Dry parts
before assembly.
FRONT SHOCK
ECX1043
ECX1037
ECX1043
ECX1057
ECX1038
ECX1036
ECX1038
ECX1043
ECX1037
• Assemble the shock and refill the shock body with silicone fluid (30
weight recommended).
ECX1037
ECX1038
ECX1036
ECX1038
ECX1043
ECX1037
ECX1040
• Slowly move the shaft and piston up and down to remove
air bubbles.
• Move the piston to the midway point of the body and install
the cap.
ECX1039
ECX1041
ECX1042
ECX1057
ECX1038
ECX1038
• Wipe off any overflowing fluid.
ECX1037
ECX1037
• When properly filled, the piston should rebound about 3/8 in
(9.5mm) after being pushed in fully.
• Install shock on vehicle.
Ride Height Adjustment
Ride height is an adjustment that affects the way the vehicle jumps,
turns and goes over bumps. Drop one end of the vehicle from
approximately 6 inches (152 mm) in height onto a flat surface. When
dropping the front of the vehicle, after the vehicle settles make sure
the front arms are equal and parallel to the flat surface. Do the same
with the rear and look at the rear to make sure both arms are
parallel with the flat surface.
Lower the front ride height to increase steering. Lower the rear ride
height to increase traction but decrease steering.
Part #
Description
ECX1036
Shock Body Set ECX1037
Shock Caps, Pistons ECX1038
Shock Parts Set ECX1039
Front Shock Shaft (2) ECX1040
Rear Shock Shaft (2) ECX1041
Front Shock Springs (2) ECX1042
Rear Shock Springs (2) ECX1043
Shock O-Ring Set FASTENERS
No.
Description
No.
Description
No.
Description
No.
Description
TAPPING BINDER HEAD M3x10mm
BINDER HEAD M3x8mm
BUTTON HEX M2.5x4mm
SET SHAFT SCREW M3x13mm
TAPPING BINDER HEAD M3x12mm
BINDER HEAD M3x12mm
BUTTON HEX M2.5x8mm
WASHER 5x7x0.5mm
TAPPING BINDER HEAD M3x16mm
BINDER HEAD M3x20mm
STEP SCREW M3x0.5x7.4mm
WASHER 3x8x0.5mm
TAPPING BINDER HEAD M3x18mm
BINDER HEAD M3x25mm
STEP SCREW M3x0.5x13.4mm
WASHER 2x7x0.5mm
TAPPING FLAT HEAD M3x10mm
BUTTON HEAD M3x30mm
STEP SCREW M3x0.5x10.5mm
FLANGED LOCK NUT M4
TAPPING FLAT HEAD M3x12mm
BUTTON HEAD M2x6mm
SET SCREW M3x3mm
LOCK NUT M3
TAPPING FLAT HEAD M3x15mm
TAPPING BUTTON HEAD M3x10mm
SET SCREW M3x12mm
E-CLIP E2.5
TAPPING FLAT HEAD M2x16mm
LOCK WASHER
RUCKUS
9
EN
TROUBLESHOOTING GUIDE
Problem
Possible Cause
Solution
Short Run Time
• Battery damaged/not charged
• Motor dirty or brushes worn
• Check/change battery
• Check/clean/replace
Sluggish Action
•Motor dirty or brushes worn
• Bind in drivetrain
• Vehicle battery is not charged
• Check/clean/replace
• Clean/adjust
• Replace/recharge
Controls Reversed
• ST. REV or TH. REV
• Change switch position
Motor/ESC overheat
• Over-geared
• Install smaller pinion
Doesn’t Operate
• Transmitter batteries low
• Transmitter powered off
• ESC powered off
• Vehicle battery is not charged
• Replace/recharge
• Power On
• Power On
• Replace/recharge
Poor Range
• Transmitter batteries low
• Transmitter antenna is damaged or loose
• Receiver antenna damaged
• Motor dirty or brushes worn
• Replace/recharge
• Check/tighten
• Check/repair/replace
• Check/clean/replace
WARRANTY AND REPAIR POLICY
Warranty Period
Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that
the Products purchased (the “Product”) will be free from defects in
materials and workmanship at the date of purchase by the Purchaser.
Limited Warranty
If you as the Purchaser or user are not prepared to accept the liability
associated with the use of this Product, you are advised to return this
Product immediately in new and unused condition to the place
of purchase.
Law: These Terms are governed by Illinois law (without regard to
conflict of law principals).
Horizon reserves the right to change or modify this warranty
without notice and disclaims all other warranties, express
or implied.
WARRANTY SERVICES
(a) This warranty is limited to the original Purchaser (“Purchaser”) and
is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER.
This warranty covers only those Products purchased from an
authorized Horizon dealer. Third party transactions are not covered by
this warranty. Proof of purchase is required for all warranty claims.
Your local hobby store and/or place of purchase cannot provide
warranty support or repair. Once assembly, setup or use of the Product
has been started, you must contact Horizon directly. This will enable
Horizon to better answer your questions and service you in the event
that you may need any assistance. For questions or assistance,
please direct your email to productsupport@horizonhobby.com, or call
877.504.0233 toll free to speak to a Product Support representative.
You may also find information on our website at
www.horizonhobby.com.
(b) Limitations- HORIZON MAKES NO WARRANTY OR
REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NONINFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOWLEDGES THAT
THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be
that Horizon will, at its option, (i) repair or (ii) replace, any Product
determined by Horizon to be defective. In the event of a defect, these
are the Purchaser’s exclusive remedies. Horizon reserves the right to
inspect any and all equipment involved in a warranty claim. Repair
or replacement decisions are at the sole discretion of Horizon. This
warranty does not cover cosmetic damage or damage due to acts
of God, accident, misuse, abuse, negligence, commercial use, or
modification of or to any part of the Product. This warranty does not
cover damage due to improper installation, operation, maintenance, or
attempted repair by anyone other than Horizon. Return of any Product
by Purchaser must be approved in writing by Horizon before shipment.
Damage Limits
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCT,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY,
NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the
liability of Horizon exceed the individual price of the Product on which
liability is asserted. As Horizon has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed nor
accepted for any resulting damage or injury. By the act of use, setup or
assembly, the user accepts all resulting liability.
10 RUCKUS
Questions, Assistance, and Repairs
Inspection or Repairs
If this Product needs to be inspected or repaired, please use the
Horizon Online Repair Request submission process found on our
website or call Horizon to obtain a Return Merchandise Authorization
(RMA) number. Pack the Product securely using a shipping carton.
Please note that original boxes may be included, but are not designed
to withstand the rigors of shipping without additional protection. Ship
via a carrier that provides tracking and insurance for lost or damaged
parcels, as Horizon is not responsible for merchandise until it arrives
and is accepted at our facility. An Online Repair Request is available
at www.horizonhobby.com http://www.horizonhobby.com under the
Repairs tab. If you do not have internet access, please contact Horizon
Product Support to obtain a RMA number along with instructions for
submitting your product for repair. When calling Horizon, you will be
asked to provide your complete name, street address, email address
and phone number where you can be reached during business hours.
When sending product into Horizon, please include your RMA number,
a list of the included items, and a brief summary of the problem. A
copy of your original sales receipt must be included for warranty
consideration. Be sure your name, address, and RMA number are
clearly written on the outside of the shipping carton.
Notice: Do not ship batteries to Horizon. If you have any issue
with a battery, please contact the appropriate Horizon Product
Support office.
Warranty Inspection and Repairs
To receive warranty service, you must include your original
EN
sales receipt verifying the proof-of-purchase date. Provided warranty
conditions have been met, your Product will be repaired or replaced
free of charge. Repair or replacement decisions are at the sole
discretion of Horizon.
Non-Warranty Repairs
Should your repair not be covered by warranty the repair
will be completed and payment will be required without
notification or estimate of the expense unless the expense
exceeds 50% of the retail purchase cost. By submitting the
item for repair you are agreeing to payment of the repair without
notification. Repair estimates are available upon request. You must
include this request with your repair. Non-warranty repair estimates
will be billed a minimum of ½ hour of labor. In addition you will be
billed for return freight. Horizon accepts money orders and cashiers
checks, as well as Visa, MasterCard, American Express, and Discover
cards. By submitting any item to Horizon for inspection or repair, you
are agreeing to Horizon’s Terms and Conditions found on our website
under the Repairs tab.
CONTACT INFORMATION
Country of
Purchase
United States of
America
Horizon Hobby
Horizon Service Center
(Electronics and engines)
Horizon Product Support
United Kingdom
Horizon Hobby Limited
Germany
Horizon Technischer
Service
France
Horizon Hobby SAS
Address
Phone Number / Email Address
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
877-504-0233
productsupport@horizonhobby.com
Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS
United Kingdom
+44 (0) 1279 641 097
sales@horizonhobby.co.uk
Hamburger Str. 10
25335 Elmshorn
Germany
14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
+49 4121 46199 66
service@horizonhobby.de
+33 (0) 1 60 47 44 70
FCC INFORMATION
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
COMPLIANCE INFORMATION FOR THE EUROPEAN UNION
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH20100820
Product(s):
ECX 1/10th Ruckus
Item Number(s): ECX2000EU; ECX2000UK; ECX2100EU; ECX2100UK
Equipment class: 1
The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of
the European R&TTE directive 1999/5/EC:
EN 300-220
EN 301 489
EN 60950
Technical requirements for Radio equipment.
General EMC requirements for Radio equipment
Safety
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
Aug 20, 2010
Steven A. Hall
Vice President
International Operations and Risk
Management
Horizon Hobby, Inc.
Instructions for disposal of WEEE by users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment
by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate
collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it
is recycled in a manner that protects human health and the environment. For more information about where you can drop off your
waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased
the product.
RUCKUS 11
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG |
VUE ÉCLATÉE DES PIÉCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI
Recommended Items
Empfohlene Werkzeuge
Outils Recommandés
Attrezzi raccomandati
M3X10
M3X12
30
3
11
46
M3X10
10
M3X10
5
12
M3X12
9
1
M3X12
M3X12
M3X12
M3X25
M3X10
M3X12
12
20
45
20
4
7
12
7
2
2
46
2
8
50
M3X15
M3X10
2
8
17
16
2
2
7
19
2
M3X12
20
2
7
8
13
19
M3x15
29
18
20
M3X10
13
M3x15
47
23
31
M3x25
32
8
7
21
15
15
13
M3X8
M3X12
19
M3X10
42 RUCKUS
M3X12
14
32
M3x12
22
PARTS DIAGRAM | EXPLOSIONSZEICHNUNG |
VUE ÉCLATÉE DES PIÉCES | ESPLOSO DEL MODELLO CON REFERENZA PEZZI
Note: The slipper clutch can
be adjusted using this locknut
(ECX1060). Fully tighten the locknut.
Then loosen the nut two full turns.
Die Rutschkupplung kann durch
diese Stopmutter eingestellt
werden (ECX1060). Ziehen Sie die
Mutter an und drehen Sie dann
volle zwei Umdrehungen zurück.
A noter: Il est possible d’ajuster
l’embrayage “patinant” par action
sur cet écrou de blocage (ECX1060).
Veillez à serrer l’écrou de blocage
à fond. Ensuite, devissez l’écrou de
trois tours complets.
Nota: La frizione può essere
regolata con questo dado
autobloccante (ECX1060). Prima
avvitate completamente il dado, poi
svitatelo 2 giri.
43
M3X3
33
33
M2.5X8
M2.5X4
42
35
22 35
35
35
35
15
M2.5X8
6
34 49
49
15
15
36 15 34 15
41 34
M3X18
37
M2X16
34
36
37
40
37
25
44
M3X12
40
39 36 34
34
36
34
34 36
34
M2X16
39
25 M3X12
45
44
M3X15
M3X12
M3X15
46
12
17
12
M3X10
44
12
44
M3X12
25
47
M3X12
M3X12
48
M3X12
M3X18
25
M3X20
48
32
40
11
50
M3X12
M3X10
24
M3x15
3
26
27
19
29
13
32
29
19
20
26
M3X12
26
31
13
20
M3X12
20
M3x12
Note: When installing wheel, make sure drive hex is aligned with the drive pin. When the drive hex
is removed, the drive pin can fall out of the axle.
Hinweis: Bitte stellen Sie sicher, dass die Kanäle 1 und 2 wie abgebildet eingesteckt sind. Die
Motorkabel können über Steckverbinder vom Regler getrennt werden.
A noter: Lors de l’installation de la roue, assurez-vous que l’écrou hexagonal est aligné avec la
broche de l’axe d’entraînement. En cas de démontage de l’écrou hexagonal, la broche de l’axe
d’entraînement peut sortir de l’axe et tomber.
Nota: Quando montate le ruote, accertatevi che il trascinatore esagonale sia allineato con la spina
del mozzo ruota. Quando togliete il trascinatore esagonale la spina può sfilarsi dal mozzo.
27
21
28
13
15
14
15
13
22
RUCKUS 43
Part # | Nummer
Numéro | Codice Description
Beschreibung
Description
Descrizione
1
ECX2008
Main Chassis Chassis
Châssis principal
Telaio principale
2
ECX1028
Servo Saver Set Servo Saver Set
Jeu de sauvegarde de servo
Set salvaservo
3
ECX2011
Cover and Rear Mount Set
4
ECX1050
Setscrew M3x12 (4) Schrauben Set M3x12 (4)
5
ECX2015
Foam Block
Schaum Block
Bloc de mousse
Spugna distanziale batteria
6
ECX1052
Motor Screw/Washer Set
Motor Screw/Washer Set
Vis Moteur/Set Rondelles
Viti per il motore/ set di rondelle
7
ECX1058
Ball Stud (6)
Kugelkopf (6)
Rondelle (6)
Sfere Uniball (6)
8
ECX1065
Shoulder Screw Set (8)
Passschrauben Set (8)
Jeu de vis d’épaulement (8)
Set viti a doppio stadio (8)
9
ECX1068
Receiver
Empfänger
Récepteur
Ricevente
10
ECX1069
Servo
Servo
Servo
Servo
11
ECX1088
Battery Hold Down
Akkuhalter
Fixation pour batterie
Piastra fermabatteria
12
ECX2012
Front/Rear Bumper Set
Stoßstange vorne hinten
Jeu de pare-chocs avant/arrière
Set paraurti ant/post
13
ECX2006
Suspension Arm Mount
Set
Querlenker Set hinten
Jeu de renfort de suspension
Supporti braccetti sosp.
14
ECX2014
Mounted Wheel/Tire (2)
Mounted Wheel/Tire (2)
Roue Montée/Pneu (2)
Ruote e gomme montate (2)
15
ECX1015
Wheel Bearing Set Radlagersatz Set
Jeu de roulement de roue
Set cuscinetti ruote
16
ECX1018
Front Suspension Arm Set Querlenker Set vorne
Jeu de bras de suspension avant
Braccetti delle sospensioni
anteriori
17
ECX1020
Shock Tower Set Dämpferbrücke
Jeu de support d’amortisseur
Supporto ammortizzatori
posteriori
18
ECX1035
Front Axle (2) Radachse vorne (2)
Axe avant (2)
Mozzi ruota anteriori (2)
19
ECX1044
Hinge Pin Set Querlenkerbolzen Set
Jeu de broche d’axe
Set perni sospensioni
20
ECX1046
Camber, Toe Link Set Spur- Sturzstangenset
Jeu de biellette de cambrure, de
pincement
Set tiranteria Camber e
convergenza
21
ECX1049
Wheel Pins (4) Radmitnehmerstifte (4)
Broches de roue (4)
Spine trascinatori ruote (4)
22
ECX1060
M4 Locknut (4)
M4 Stopmutter (4)
Ecrou de blocage M4 (4)
Dadi autobloccanti M4 (4)
23
ECX1089
Steering Block Set
Lenkhebel Set
Jeu de bloc de direction
Fuselli sterzo
24
ECX1019
Rear Suspension Arm Set Querlenker Set hinten
Jeu de bras de suspension arrière
Braccetti delle sospensioni
posteriori
25
ECX1021
Transmission Case Set Getriebegehäuse
Ensemble carter de transmission
Set scatola trasmissione
26
ECX1031
Driveshaft Set Antriebswellen Set
Ensemble arbre de transmission
Set semiassi
27
ECX1032
Driveshaft Pivot Ball (4) Antriebswellengelenk (4)
Boule pivot d’arbre de
transmission (4)
Snodi semiassi (4)
28
ECX1034
Rear Axle (2) Wellenmitnehmer hinten (2)
Axe arrière (2)
Mozzi ruota anteriori (2)
29
ECX1045
Hinge Pin Screws (8) Querlenkerbolzen Schrauben (8)
Vis de broche d’axe (8)
Viti per perni sospensioni (8)
30
ECX1070
ESC
Regler / ESC
CEV
Variatore elettronico (ESC)
31
ECX1090
Rear Hub Carrier Set
Hinterer Rad Träger Set
Jeu de porte-moyeu arrière
Portamozzi posteriori
32
ECX1037
Shock Caps, Pistons
Stoßdmämpferkappen Kolben
Obturateurs d’amortisseur, pistons Set tappi e pistoni ammortizzatori
33
ECX1027
Gear Cover
Gear Cover
Carter de Réducteur
Copertura per ingranaggi
34
ECX1022
Transmission Gear Set Getriebe
Ensemble couronne de
transmission
et ingranaggi trasmissione
35
ECX1024
Slipper Clutch Plates, Pads,
Spring Rutschkupplung Teilesatz
Plateaux d’embrayage patinant,
plaquettes, ressort
Piattelli frizione, disco, molla
36
ECX1025
Transmission Idler Shaft,
Drive Pins Hauptgetriebewelle Set
Arbre secondaire de transmission, axes d’entraînement
Alberino intermedio con spina
37
ECX1026
Transmission Drive Shaft (2) Getreibeausgangswelle (2)
Axe d’arbre de transmission (2)
Mozzi Differenziale (2)
38
ECX1052
Washer Set
Unterlegscheiben Set
Jeu de rondelles
Set rondelle
39
ECX1055
Bearings 10x15x4 (2)
Lager 10x15x4 (2)
Roulements 10x15x4 (2)
Cuscinetti 10x15x4 (2)
40
ECX1059
M3 Locknut (4)
M3 Stopmutter (4)
Ecrou de blocage M3 (4)
Dadi autobloccanti M3 (4)
41
ECX1076
Spur Gear
Hauptzahnrad
Couronne
Corona
42
ECX1073
19-Tooth Pinion Gear
19-Tooth Pinion Gear
Pignon 10 dents
Pignone a 19 denti
43
ECX1071
Motor
Motor
Moteur
Motore
44
ECX1048
Body Clip
Body Clip
Clips Carrosserie
Clippe per carrozzeria
45
ECX2010
Body Post Set
Body Post Set
Set Plots Carrosserie
Set di sostegni per la carrozzeria
46
ECX2009
Body Mount Set
Body Mount Set
Set Montage Carrosserie
Set di montaggio per la carrozzeria
47
ECX2007
Skid Plate Set
Skid Plate Set
Set Plaque Chassis
Set pistre di protezione
48
ECX2013
Rear Holder Set
Rear Holder Set
Set de Maintien Arrière
Set supporto posteriore
49
ECX1023
Top Shaft/Spacer
Top Shaft/Spacer
Set de Goupilles
Set di spessori
50
ECX1033
Setscrew M3x10
Sicherungsschrauben (4)
Vis (4)
Viti (4)
44 RUCKUS
mont de couverture et arrière
Jeu de vis M3x12 (4)
Grani M3x12 (4)
NOTES / HINWEIS / A NOTER / NOTA
RUCKUS 45
NOTES / HINWEIS / A NOTER / NOTA
46 RUCKUS
NOTES / HINWEIS / A NOTER / NOTA
RUCKUS 47
Created 10/10
22425.1
ECX2000, ECX2000UK, ECX2000EU, ECX2000AU
ECX2100, ECX2100UK, ECX2100EU, ECX2100AU
© 2010 Horizon Hobby, Inc.