Barco R9002249 Owner`s manual

VISION
1609s
R9002240
R9002249
OWNER'S MANUAL
BARCO PROJECTION SYSTEMS
VISION
1609s
R9002240
R9002249
OWNER'S MANUAL
Date :
131097
Art. No. :
R5975688
Due to constant research, the information in this manual is subject to change without notice.
Produced by BARCO NV, October 1997.
All rights reserved.
Trademarks are the rights of their respective owners.
BARCO nv/Projection Systems
Noordlaan 5
B-8520 Kuurne
Belgium
Tel : +32/56/368211
Fax : +32/56/351651
E-mail : sales.bps@barco.com
Visite Barco at the web : http://www.barco.com
Printed in Belgium
Table of Contents
Table of contents ................................................................................................................................................................................. i
Safety instructions .........................................................................................................................................................................
On safety ...................................................................................................................................................................................
On installation .............................................................................................................................................................................
On servicing ...............................................................................................................................................................................
On cleaning ................................................................................................................................................................................
On repacking ..............................................................................................................................................................................
On illumination .............................................................................................................................................................................
1-1
1-1
1-2
1-2
1-2
1-2
1-2
Location and Functions of Control ..............................................................................................................................................
Rear panel terminology ..............................................................................................................................................................
Front panel terminology ..............................................................................................................................................................
Control panel terminology ..........................................................................................................................................................
a. The Local Keypad ..................................................................................................................................................................
b. RCU control panel terminology ...............................................................................................................................................
2-1
2-1
2-1
2-2
2-2
2-2
Connections .....................................................................................................................................................................................
AC Power (mains) Cord Connection .........................................................................................................................................
Power Check ..............................................................................................................................................................................
Switching On/Off .......................................................................................................................................................................
Signal Input Connection to the Projector : ..................................................................................................................................
Connecting a Composite Video source to port 1. .....................................................................................................................
Connecting a S-Video or Video source to port 2. .....................................................................................................................
Connecting a RGB Analog source to port 3. .............................................................................................................................
Connecting a RGB Analog source to port 4/5. ..........................................................................................................................
Connecting a RGB Analog source with Tri-level sync to port 4/5.(option) ..............................................................................
Connecting a Component Video source to port 4/5. .................................................................................................................
Connecting a Component Video source with Tri-level sync to port 4/5.(Opion) .....................................................................
Peripheral equipment ..................................................................................................................................................................
Connecting a RCVDS 05 switcher to the projector ..................................................................................................................
Connecting a VS05 switcher to the projector. .........................................................................................................................
Connecting an IR Remote Receiver to the projector .................................................................................................................
3-1
3-1
3-1
3-1
3-2
3-3
3-3
3-4
3-4
3-5
3-5
3-5
3-6
3-6
3-6
3-6
Controlling ........................................................................................................................................................................................
Battery installation in the RCU. ...................................................................................................................................................
How to use your RCU ................................................................................................................................................................
Projector Address ......................................................................................................................................................................
How to display a projector address? ........................................................................................................................................
How to program an address into the RCU? ..............................................................................................................................
Input selection ............................................................................................................................................................................
Analog Picture Controls .............................................................................................................................................................
Controlling chained projectors. ..................................................................................................................................................
4-1
4-1
4-2
4-2
4-3
4-3
4-3
4-4
4-4
Start up of the Adjustment Mode ............................................................................................................................................... 5-1
Adjustment Mode ....................................................................................................................................................................... 5-1
Random Access Adjustment Mode ............................................................................................................................................ 6-1
Starting-Up the Random Access Adjustment mode. ................................................................................................................. 6-1
Overview 'Random Access Adjustment' mode ........................................................................................................................ 6-1
Selecting Setup Pattern .............................................................................................................................................................. 6-3
Internal Cross Hatch Pattern ...................................................................................................................................................... 6-3
Random access adjustment mode selection menu. .................................................................................................................. 6-4
Picture Tuning ............................................................................................................................................................................. 6-4
Color Balance ............................................................................................................................................................................. 6-4
Sync Fast/Slow Adjustment ...................................................................................................................................................... 6-5
Peaking ....................................................................................................................................................................................... 6-5
Clamp Tuning .............................................................................................................................................................................. 6-5
Port 2 : Video or S-Video ........................................................................................................................................................... 6-6
Line Doubler ............................................................................................................................................................................... 6-6
Color Select ................................................................................................................................................................................ 6-6
Focusing ..................................................................................................................................................................................... 6-7
Focusing color select. ................................................................................................................................................................ 6-7
Blue on source ........................................................................................................................................................................... 6-7
Geometry Adjustments .............................................................................................................................................................. 6-8
Horizontal Phase Adjustment ..................................................................................................................................................... 6-8
Raster Shift Adjustment ............................................................................................................................................................. 6-9
Left-Right (east-west) Adjustments ....................................................................................................................................... 6-10
Seagull correction .................................................................................................................................................................... 6-11
Left Side Correction ................................................................................................................................................................. 6-11
Top-Bottom (north-south) Adjustments ................................................................................................................................... 6-12
Seagull Correction .................................................................................................................................................................... 6-13
Horizontal Size Adjustment ...................................................................................................................................................... 6-13
Vertical Linearity Adjustment ................................................................................................................................................... 6-14
Vertical Size Adjustment ......................................................................................................................................................... 6-14
5975688 BARCOVISION 1609s 131097
i-1
Table of Contents
Blanking Adjustments ............................................................................................................................................................... 6-15
Convergence Adjustment ........................................................................................................................................................ 6-16
Service mode ...................................................................................................................................................................................
Starting up the Service mode. ...................................................................................................................................................
Overview flowchart 'Service' mode. ........................................................................................................................................
Identification ...............................................................................................................................................................................
Copy a block ...............................................................................................................................................................................
Deletion of blocks .......................................................................................................................................................................
Deleting block by block ...............................................................................................................................................................
Deletion of all blocks ..................................................................................................................................................................
Change password .....................................................................................................................................................................
Change Language ......................................................................................................................................................................
Run time ......................................................................................................................................................................................
Set to midposition .......................................................................................................................................................................
Undo Midposition ........................................................................................................................................................................
Convergence Mid .......................................................................................................................................................................
Undo Convergence Mid(position) ..............................................................................................................................................
Dynamic Astigmatism (spot shape adjustment) ........................................................................................................................
G2 Adjust ...................................................................................................................................................................................
Gamma corrections ....................................................................................................................................................................
CRT run in cycle .........................................................................................................................................................................
Projector Warm Up .....................................................................................................................................................................
CRT Drive Mode .........................................................................................................................................................................
7-1
7-1
7-1
7-2
7-2
7-3
7-3
7-3
7-4
7-4
7-4
7-5
7-5
7-5
7-5
7-6
7-7
7-7
7-7
7-8
7-8
Messages, warnings and failures .............................................................................................................................................. 8-1
Options .............................................................................................................................................................................................. 9-1
Appendix A : Orbiting .......................................................................................................................................................................... A-1
Appendix B : Adjsutment Blocks and Source Numbers 90-99 .......................................................................................................... B-1
i-2
5975688 BARCOVISION 1609s 131097
Safety Instructions
1
SAFETY INSTRUCTIONS
Notice on Safety
This equipment is built in accordance with the requirements of the
international safety standards EN60950, UL 1950 and CSA C22.2
No.950, which are the safety standards of information technology
equipment including electrical business equipment.
These safety standards impose important requirements on the use of
safety critical components, materials and isolation, in order to protect
the user or operator against risk of electric shock and energy hazard,
and having access to live parts.
Safety standards also impose limits to the internal and external
temperature rises, radiation levels, mechanical stability and strength,
enclosure construction and protection against the risk of fire.
Simulated single fault condition testing ensures the safety of the
equipment to the user even when the equipment's normal operation
fails.
INSTALLATION INSTRUCTIONS
Before operating this equipment please read this manual
thoroughly, and retain it for future reference.
Installation and preliminary adjustments should be performed
by qualified BARCO personnel or by authorized BARCO
service dealers.
OWNER’S RECORD
The part number and serial number are located at the back side of the
projector. Record these numbers in the spaces provided below. Refer
to them whenever you call upon your BARCO dealer regarding this
product.
PART NUMBER :
WARNING
TO PREVENT FIRE OR ELECTRICAL SHOCK
HAZARD, DO NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE
FEDERAL COMMUNICATION COMMISSION (FCC STATEMENT)
This equipment has been tested and found to comply with the limits
of a class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
Instructions to the user :
If this equipment does cause interference to radio or television
reception, the user may try to correct the interference by one or more
of the following measures :
- Re-orientation of the receiving antenna for the radio or television.
- Relocate the equipment with respect to the receiver.
- Plug the equipment into a different outlet so that the equipment and
receiver are on different branch circuits.
- Fasten cables connectors to the equipment by mounting screws.
Note :
The use of shielded cables is required to comply within the limits of
Part 15 of FCC rules and EN55022.
* All the safety and operating instructions should be read before using
this unit.
* The safety and operating instructions manual should be retained for
future reference.
SER. NUMBER :
* All warnings on the equipment and in the documentation manuals
should be adhered to.
DEALER :
* All instructions for operating and use of this equipment must be
followed precisely.
On safety
1. This product should be operated from an AC power source.
This projector may be connected to an IT-power system.
Operating AC power voltage of the projector:
The lightning flash with an arrowhead within a
triangle is intended to tell the user that parts
inside this product may cause a risk of electrical
shock to persons.
The exclamation point within a triangle is intended to tell the user that important operating
and/or servicing instructions are included in the
technical documentation for this equipment.
5975688 BARCOVISION 1609S 131097
BARCOVISION 1609s
Art.No. R9002240 (230V AC)
Art. No R9002249 (120V AC)
Consult your dealer to switch over from 230Vac to 120 Vac or from
120Vac to 230 Vac.
If you are not sure of the type of AC power available, consult your
dealer or local power company.
2. This product is equipped with a 3-wire grounding plug, a plug
having a third (grounding) pin. This plug will only fit into a groundingtype power outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace your
obsolete outlet. Do not defeat the purpose of the grounding-type plug.
1-1
Safety Instructions
WARNING FOR THE CUSTOMERS: THIS APPARATUS MUST BE
GROUNDED (EARTHED) via the supplied 3 conductor AC power
cable. (If the supplied power cable is not the correct one, consult your
dealer.)
Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. Mains lead (Power cord) with CEE 7 plug:
The wires of the mains lead are colored in
accordance with the following code.
Green and yellow:earth (safety earth)
Blue:
neutral
Brown:
line (live)
B. Power cord with ANSI 73.11 plug:
The wires of the power cord are colored in
accordance with the following code.
Green/yellow: ground
White:
neutral
Black:
line (live)
3. Do not allow anything to rest on the power
cord. Do not locate this product where persons will walk on the cord.
To disconnect the cord, pull it out by the plug. Never pull the cord itself.
4. If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the extension
cord does not exceed the extension cord ampere rating. Also make
sure that the total of all products plugged into the wall outlet does not
exceed 15 amperes.
5. Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
A. When the power cord or plug is damaged or frayed.
B. If liquid has been spilled into the equipment.
C.If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating
instructions are followed.
Note : Adjust only those controls that are covered by the operating
instructions since improper adjustment of the other controls may
result in damage and will often require extensive work by a qualified
technician to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, indicating
a need for service.
Replacement parts - When replacement parts are required, be sure
the service technician has used original BARCO replacement parts
or authorized replacement parts which have the same characteristics
as the BARCO original part. Unauthorized substitutions may result in
degraded performance and reliability, fire, electric shock or other
hazards. Unauthorized substitutions may void warranty.
Safety check - Upon completion of any service or repairs to this
projector, ask the service technician to perform safety checks to
determine that the product is in proper
operating condition.
On cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6. Lightning - For added protection for this video product during a
lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage
to the projector due to lightning and AC power-line surges.
- To keep the cabinet looking brand-new, periodically clean it with a
soft cloth. Stubborn
stains may be removed with a cloth
lightly dampened with mild detergent solution. Never use strong
solvents, such as thinner or benzine, or abrasive cleaners, since
these will damage the cabinet.
- To ensure the highest optical performance and resolution, the
projection lenses are specially treated with an anti-reflective coating, therefore, avoid touching the lens. To remove dust on the lens,
use a soft dry cloth. Do not use a damp cloth, detergent solution, or
thinner.
On installation
On repacking
1. Do not place this equipment on an unstable cart, stand, or table.
The product may fall, causing serious damage to it.
Save the original shipping carton and packing material; they will come
in handy if you ever have to ship your equipment. For maximum
protection, repack your set as it was originally packed at the factory.
Never spill liquid of any kind on the product. Should any liquid or solid
object fall into the cabinet, unplug the set and have it checked by
qualified service personnel before resuming operations.
2. Do not use this equipment near water.
3. Slots and openings in the cabinet and the back or bottom are
provided for ventilation; to ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface. This
product should never be placed near or over a radiator or heat
register.
The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
4. Do not block the projector cooling fans or free air movement under
and around the projector. Loose papers or other objects may not be
nearer to the projector than 4" on any side.
On servicing
Do not attempt to service this product yourself, as opening or
removing covers may expose you to dangerous voltage potentials
and risk of electric shock!
1-2
On illumination
In order to obtain the best quality for the projected image, it is
essential that the ambient light which is allowed to fall on the screen
be kept to an absolute minimum.
When installing the projector and screen, care must be taken to avoid
exposure to ambient light directly on the screen. Avoid adverse
illumination on the screen from direct sunlight or fluorescent lighting
fixtures.
The use of controlled ambient lighting, such as incandescent spot
light or a dimmer, is recommended for proper room illumination.
Where possible, care should also be taken to ensure that the floors
and walls of the room in which the projector is to be installed are nonreflecting, dark surfaces. Brighter surfaces will tend to reflect and
diffuse the ambient light and hence reduce the contrast of the
projected image on the screen.
5975688 BARCOVISION 1609S 131097
Location and Function of Controls
2
LOCATION AND FUNCTION OF CONTROLS
REAR PANEL TERMINOLOGY
3257 3257
5*%+9
9,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
5('VWDQGE\
9V\QF
3257
&20081,&$7,21
3257
69,'(2
2))
5
1
2
3
2))
21
RKP
RKP
Communication Port (800 peripherals)
* allows communication between the RCVDS switcher and
the projector.
* allows connection of a remote IR receiver unit to the
projector.
5
Port 4/5 : RGB-S Input (5x BNC connector):
RGB-S input : allows a character generator, microcomputer, video camera, etc. having analog RGB output to be
connected to the projector.
Important : projector ("Operational" or "Standby") mode is
defined during the installation of the projector. (Refer to a
qualified technician for change).
6
- signals RED-GREEN-BLUE
- COMPOSITE sync. signal
- Tri level sync signal (option)
VIDEO Input (Composite video, 2x loop-through BNC
connector): allows a video tape recorder, video camera,
color receiver/monitor, etc. having video line output to be
connected to the projector.
75 ohm Termination Switch for Video signals
Projector Pilot Lamp : indicates the status of the projector.
- unlit : mains (power) switch is not pressed.
- lit : mains (power) switch is pressed and the indicated
color shows the projector mode:
Green color : operational mode of the projector.
Red color : standby mode of the projector.
Port 3
RGB Analog Input (9 pin female sub D connector). Allows
a character generator, microcomputer, etc. having analog
RGB outputs to be connected to the projector.
Line inputs:
4
%
*
21
7
S-VIDEO Input: S-Video or Video in, depending on the
priority setting in the Picture Tuning menu.
For S-Video : Separated Y/C (luma-chroma) signal inputs
and outputs for higher quality playback of Super VHS
signals (4-pin S-VIDEO connector loop-through).
75 ohm Termination Switch for S-Video signals
For Video : Composite video inputs on pin 1 and 3.
Power Switch : press the switch to turn the projector ON.
Depending on the hardware set-up of the projector during
installation, the projector switches to ‘Standby’ or to
‘Operational' mode. If in standby, the standby LED lights
up.
V NOM 120/230 Volt
7/5Amp
I MAX
50/60Hz
FREQ
1
, 6 5
782
6 5
5
,
56,1
1
2
56287
,5
(7 20( 5
5(027(
FRONT PANEL TERMINOLOGY
RS 232 Input Port
Connection between the projector and an IBM PC (or
compatible) or MAC (RS422) for remote computer control
and data communication.
RS 232 Output Port
RS 232 Input Port allows a communication link for PC or MAC
to the next projector in a series of projector.
5975628 BARCOGRAPHICS 1209S 010797
3
4
5
IR Sensor
receiver for control signals transmitted from the RCU.
IR Remote
Connector for remote input for hard wired remote control
AC Power input
2-1
Location and Function of Controls
Control panel terminology
a. The Local Keypad (built in RCU)
Gaining Access
325 7
325 7
5*% + 9
9 ,' (2
The local keypad is built in into the rear of the projector. Push once
on the door cover and it will open. It is possible to turn it 90°.
This local keyboard has the same functions as the Remote Control
Unit (RCU)
32:(50$,16
352-(&7 2502'(
*5((1RSHUDWLRQDO
&RPS+V\ QF
5('VWDQG E\
9V\QF
3257 3257 5(027 (
&20081,&$7,21
3257 69,'(2
2))
5
*
21
RKP
%
2))
21
RKP
EXLOWLQ5&8
b. RCU control panel terminology
This remote control includes a battery powered infrared (IR) transmitter that allows the user to control the projector remotely.
This remote control is used for source selection, control, adaptation
and set-up. It includes automatic storing of :
- picture controls (Brightness, Sharpness,....)
- picture geometry adjustments
- convergence adjustments
Other functions of the remote control are:
- switching between standby and operational modes
- switching to "pause" (blanked picture, full power for immediate
restarting)
- direct access to all connected sources
- variable adjustment speed : when pushing continuously on the
control stick or the picture keys, the adjustment will be executed in
an accelerated fashion.
stand-by
(;,7
pause/park
(17(5
$'-
67%<
3$86(
-
+
8
-
+
5
6
-
3
4
-
+
1
2
-
+
9
0
7
tint
&2/25
2
ADJ. : adjust key, to enter or exit the adjustment mode.
3
Address key (recessed key), to enter the address of the
projector (between 0 and 9). Press the address key,
followed by pressing one digit button between 0 and 9.
4
STBY : stand by button :
- to initiate remote power up operation
- to stop projection without main power off.
color
6+$531(66
7,17
Back light key : when activated, all keys will be lit up and
visible in the dark.
sharpness
7(;7
1
brightness
+
contrast
%5,*+71(66
&2175$67
5
Pause :to blank the image, press PAUSE. The image
disappears but full power is retained for immediate restarting.
6
Digit buttons : direct input selection.
7
Picture controls : use these buttons to obtain the desired
level (see also 'Controlling') for each picture function.
8
TEXT : when adjusting one of the image controls during a
meeting, the displayed bar scale can be removed by
pressing 'TEXT' key first. To re-display the bar scale on the
screen, press 'TEXT' key again. 'TEXT' key is only active in
operational mode. When 'TEXT' is off, no warning message
will be displayed.
32a
9
ENTER : to start up the adjustment mode or to confirm an
adjustment or selection in the adjustment mode.
10
EXIT : to leave the adjustment mode or to scroll upwards
when in the adjustment mode.
2-2
11
Control disk : to make menu selections when in the
adjustment mode. Also allows to increment or decrement an
adjustment in the adjustment mode.
control disk up = up arrow in the menus
control disk down = down arrow in the menus
control disk to the right = arrow to the right on the menus
control disk to the left = arrow to the left on the menus
12
RC operating indication : lights up when a button on the
remote control is pressed. (This is a visual indicator to check
the operation of the remote control)
5975628 BARCOGRAPHICS 1209S 010797
Connections
3
CONNECTIONS
AC Power (mains) Cord Connection
Use the supplied power cord to connect your projector
to the wall outlet. Plug the female power connector into
the male connector at the frontside of the projector.
V NOM 120/230 Volt
7/5Amp
I MAX
50/60Hz
FREQ
1
, 6 5
7 82
6 5
5
,
56,1
56287
,5
(7 20( 5
5(027(
Power Check
Power voltage indication on sticker on the rear side of the projector.
The power voltage is indicated by the art. no.
Warning !
Check if the indicated power voltage corresponds to that of the wall
outlet.
Art. No. R9000972 must be connected to a 230 VAC power source.
Art. No. R9000977 must be connected to a 120 VAC power source.
If the wall outlet voltage is different, call a qualified technician for
power adaptation of the projector.
Switching On/Off
The projector is switched ON and OFF using the power (mains)
switch ON/OFF.
Pressed : ON
Not pressed : OFF
The projector can start now in the 'operational mode' (image displayed) or in the 'stand by mode', depending on the position of the
'power up' dip switch on the controller unit. This DIP switch must be
set during installation by a qualified technician. If you want to change
this start up mode, call a qualified technician.
32:(50$,16
352-(&72502'(
2
*5((1 RSHUDWLRQDO
5('VWDQGE\
3257
Stand by indication lamp :
69,'(2
21
P
2))
21
R KP
no light up : projector switched off
green color : projector in Operational mode
red color : projector is in Standby mode.
When starting up the projector, with the power switch or via the
stand-by key, the projector can start up in two ways if the "CRT run
in" cycle option is switched OFF.
- full white image (projector warm up) or
- immediately image display.
The way of starting up can be set in the service mode.
5975688 BARCOVISION 1609S 131097
3-1
Connections
Start up with full white image.
The next menu will be displayed for 30 seconds.
a. Start up with warm up period.
PROJECTOR WARM UP
If no action is taken, a white image will be displayed for 20 minutes.
This white image will be shifted on the faceplate of the CRT to avoid a CRT burn in.
During this warm up period, it is possible to interrupt this white image projection by
pressing the EXIT key. The previous menu will be repeated for another 30 seconds
but the remaining time will be indicated.
If EXIT is pressed, the remaining warm up period will be shipped.
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES;
FOR IMMEDIATE USE OF
THE PROJECTOR, PRESS
<EXIT>
WARNING : SKIPPING THIS
PROCEDURE CAN REDUCE
THE INITAL PROJECTED
IMAGE.
During the warm up period, every 30 seconds a text box with the remaining time will
be displayed on the screen for 2 seconds. This text box will be displayed every time
on another place.
THIOS OPTION CAN BE
DISABLED IN THE SERVICE
MENU
REMAINING
PROJECTOR
WARM UP
TIME
18.5 MIN
If another key, different from EXIT, is pressed, a text box with following text will be
displayed :
Please use <EXIT> to leave this procedure.
b. Start up without warm up period.
PLEASE USE
<EXIT> TO
LEAVE THIS
PROCEDURE
If the EXIT key is pressed, the warm up period will be skipped and the projector is
immediately ready for use.
Warning : skipping this warm up procedure can reduce the initial picture
quality of the projected image.
Signal Input Connection to the Projector :
- Composite Video
- S-Video
- RGBS or RGsB
- RGB3S or RG3sB (option)
- Component Video
Projector input
32:(50$,16
352-(&72502'(
32575(027(
5('VWDQGE\
9V\QF
3257
&20081,&$7,21
3257
69,'(2
2))
5
*
%
2))
21
21
RKP
RKP
Press Digit Button
1
Comp. Video
1
2
S-Video1/Comp. Video*
2
3
RGB2
3
1
2
4/5
RGB2
4 or 5
4/5
Component video3
6
4/5
RGB with Tri level sync4
7
4/5
Component video
with Tri-level sync5
8
Only available when the optional Tri-level sync module is installed.
3-2
9 ,'(2
*5((1RSHUDWLRQDO
Port No
3257
3257 5*%+9 &RPS+V\QF
3
4
5
*
Input signal Y/C (luma/chroma)
Input signal : R, G and B with automatic sync
detection between seperate sync (separate
composite sync or with separate Hor and Vert.
sync) or sync on green (composite sync).
Input signal : R-Y, Y and B-Y with separate
composite sync or with separate Hor and Vert.
sync or with composite sync on Y.
Input signal : R, G and B with separate Tri level
sync or with Tri-level sync on green.
Input signal : R-Y, Y and B-Y with separate Tri
level sync or with composite Tri-level sync.
Video or S-Video : switchable in the Picture
Tuning menu.
5975688 BARCOVISION 1609S 131097
Connections
Connecting a Composite Video source to port 1.
Composite video signals from a VCR, OFF air signal decoder, etc..
3257
3257
5*%+9
9,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
&RPS +V\QF
3257 5(027(
5(' VWDQGE\
9V\QF
3257
&20081,&$7,21
3257
69,'(2
2))
5
*
2))
21
21
RKP
RKP
%
&RPSRVLWH
YLGHR
Video input selection :
7RQH[WSURMHFWRU
with the RCU or the build in RCU : press digit button 1
79WXQHUHJ79'0VWHUHR
* Note : if using the loop-through Video output, then set the
Termination Switch to the "OFF" position.
$XGLRDPSOLILHU
9&5
Connecting a S-Video or Video source to port 2.
Separate Y-luma/C-chroma signals for higher quality playback of Super VHS signals.
3257 3257
5*%+9
9 ,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
5('VWDQGE\
9V\QF
3257
&20081,&$7, 21
3257
69,'(2
2))
5
4 pin connector configurations:
For S-video:
Pin 1: earth(ground) luminance
Pin 2: earth(ground) chrominance
Pin 3: luminance signal(Y)
1Vpp ±3dB
Pin 4: chrominance signal(C)
300mVpp ±3dB
3
4
1
2
For video:
Pin 1: earth(ground) video
Pin 2: not connected
Pin 3: video signal
Pin 4: not connected
*
%
2))
21
21
RKP
RKP
/XPD&KURPD
WRQH[WSURMHFWRURU
WRDPRQLWRU
Input selection
9&569+6
$XGLRDPSOLILHU
with the RCU or the build in RCU : press digit button 2
Depending on the priority setting in the Picture Tuning menu,
Video or S-Video can be displayed.
If the setting is not correct, start up the adjustment mode by
pushing on th ADJUST key.
Select 'Random Access' and press ENTER.
ADJUSTMENT MODE
Select a path from below :
Select 'Selected source' and press ENTER.
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Source 02
Choose a setup pattern
Select with
or
from below :
then <ENTER>
<EXIT> to return.
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Highlight 'Picture Tuning' and press ENTER.
Highlight Port 2 : Video and press ENTER to toggle between VIDEO
or S-VIDEO.
Press EXIT to return.
Press ADJUST to return to operational mode.
* Note: When using the Port 2 loop-through output, set the Termination
Switch in the "OFF" position.
5975688 BARCOVISION 1609S 131097
Source 02
RANDOM ACCESS
ADJUSTMENT
MODE
Select with
or
PICTURE TUNING
then <ENTER>
GEOMETRY
<EXIT> to return.
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
PICTURE TUNING
SOFT EDGE
Select with COLOR
or
BALANCE
then <ENTER>
SYNC : FAST
<EXIT> to return.
PORT2 : S-VIDEO
LINE DOUBLER : ON
Select with
or
<ENTER> to accept
<EXIT> to return.
3-3
Connections
Connecting a RGB Analog source to port 3.
Connect your RGB source via an interface to Port 3.
Always use an interface when a computer and local monitor have
to be connected to the projector.
Barco interfaces which can be
Universal analog interface
RGB 120 MHz analog interface
VGA interface 120V
230V
MAC interface 120V
230V
MAGIK interface 120V
230V
applied :
R9826100
R9826570
R9828079
R9828070
R9828059
R9828050
R9828129 & R9828128
R9828120 & R9828121
3257
3257
5*%+9
9,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWL RQDO
&RPS+V\QF
5('VWDQGE\
9V\QF
3257
32575(027(
&20081,&$7,21
3257
69,'(2
2))
5
RGB analog input with automatic sync detection. (Separate H and
V sync inputs, with composite sync input or with sync signals on
green)
21
$1$/2* ,17(5) 0+]
,1387
%
*
+
2))
21
21
RKP
RKP
%
9
2))
5
Pin
1
2
3
4
5
6
7
8
9
*
, 13
configuration D9 connector of the Analog input.
not connected
ground RGBS
RED
GREEN
BLUE
ground RGBS
ground RGBS
Hor/comp. sync
Vert. sync
RKPWHUP
,1 3
L QYHU
361
Analog Input Selection :
with the RCU or build in RCU, press digit button 3.
Connecting a RGB Analog source to port 4/5.
RGB analog input terminals with separate H and V sync inputs, with
composite sync input or with sync signals on green (automatic sync
detection).
Always use an interface when a computer and local monitor have
to be connected to the projector. See 'Connecting a RGB Analog
source to port 3' for a list of BARCO interfaces which can be applied.
3257 3257 32:(50$,16
352-(&72502'(
9 ,'( 2
5*%+9 *5((1RSHUDWLRQDO
&RPS+V\QF
5('VWDQGE\
9V\QF
3257
32575(027(
&20081,&$7,21
3257
69,'(2
2))
5
2))
21
RKP
RKP
%
*
21
RGB input selection :
(RGB : R, G, B signals with automatic sync detection)
with the RCU or the build in RCU : press digit
button 4 or 5
21
2
$1$/2*,17(5)0+]
,1387
%
5
*
+
9
,13
RKPWHUP
3-4
,13
LQYHU
5975688 BARCOVISION 1609S 131097
Connections
Connecting a RGB Analog source with Tri-level
sync to port 4/5.
(option)
RGB analog input terminals with Tri level sync input or with
Tri-level sync on green. The projector detects automatically where the sync signal is located.
3257
3257
5*%+9
9,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
5('VWDQGE\
9V\QF
3257
&20081,&$7,21
3257
69,'(2
2))
5
%
*
2))
21
21
RKP
RKP
RGB input selection :
(RG3sB : R, G, B signals with automatic Tri-level sync detection)
with the RCU or the build in RCU : press digit button 7
$ X GLRDPSOLILHU
9&5+'79SOD\HU
Connecting a Component Video source to
port 4/5.
A component video (R-Y, Y, B-Y) with sync signals can be connected to the projector via the Port 4/5. The projector detects
automatically where the sync signal is located.
3257
3257
5*%+9
9,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
5('VWDQGE\
9V\QF
3257
&20081,&$7,21
3257
69,'(2
2))
5
%
*
2))
21
21
RKP
RKP
To select the component video input :
with the RCU or the build in RCU : press digit button 6.
$ X GLRDPSOLILHU
9&5+'79SOD\HU
Connecting a Component Video source with Trilevel sync to port 4/5.
(Opion)
A component video (R-Y, Y, B-Y) with Tri-level sync signals can be
connected to the projector via the Port 4/5. The projector detects
automatically where the sync signal is located.
3257
3257
5*%+9
9,'(2
32:(50$,16
352-(&72502'(
*5((1RSHUDWLRQDO
&RPS+V\QF
32575(027(
5('VWDQGE\
9V\QF
3257
&20081,&$7,21
3257
69,'(2
2))
5
*
%
2))
21
21
RKP
RKP
To select the component video input :
with the RCU or the build in RCU : press digit button 8.
$ X GLRDPSOLILHU
9&5+'79SOD\HU
5975688 BARCOVISION 1609S 131097
3-5
Connections
PERIPHERAL EQUIPMENT
Connecting a RCVDS 05 switcher to the projector
- Up to 20 inputs with the RCVDS 05 switcher and up to 90 inputs
when 10 RCVDS switchers are linked via the expansion modules.
- Serial communication with the projector.
- Remote control buttons on the RCVDS to control the
projector (source selection and analog settings)
- The selected source number will be displayed on a 2 digit display
and the selected input modules will be indicated with a LED on the
rear.
For more information about the use of tje RCVDS, consult the Owner's
Manual of the RCVDS.
Order number : RCVDS05 : R5975765
Connecting a VS05 switcher to the projector.
The VS05 can switch up to 5 Composite Video sources, 3 S-Video
Sources and 1 RGB analog or component Video source to the
projector. In addition, an audio signal associated with the source,
can be switched to an audio amplifier.
Order number : R9827890.
For more information about the use of the VS05, consult the VS05
Owner's Manual, order number : R5975245.
Connecting an IR Remote Receiver to the
projector.
This infra-red receiver unit makes it possible to control the projector
from another room. There is a communication line cable between the
IR receiver and the projector or the RCVDS. The infrared control
information from the Remote Control Unit is sent to the IR Remote
Receiver. The IR Remote Receiver 800 displays the selected source
on a 7-segment display.
Order number : R9827515.
3-6
5975688 BARCOVISION 1609S 131097
Controlling
4
CONTROLLING
Caution : Do not display a stationary image with full brightness
and contrast for longer than 20 min., otherwise you risk damage
to the CRT's.
Battery installation in the RCU.
A new battery is delivered inside the plastic bag with the power cord. Before using the RCU, install
first the battery.
Remove the battery cover on the backside of the RCU by pushing the indicated handle a little to the
bottom of the RCU. Lift up the top side of the cover at the same time (fig. 1).
Insert the new 9 V battery (type 6F22S or equivalent) in the lower compartment and connect the battery
to the contact plate.
Insert the battery into the lower compartment and put the cover back.
Insert here,
behind the
plastic cover, the
'Insert card for
RCU'. You can
cut out the
correct insert
card on one of
the last pages of
this manual.
Contact
plate
Battery
fig.1
fig.2
310a.DRW
5975688 BARCOVISION 1609S 131097
4-1
Controlling
The BARCOVISION 1609s can be controlled with
a. the RCU
b. the hardwired RCU (cable not included)
c. the built-in RCU (local keypad)
c) RCU used in a hardwired configuration.
56,1
56287
The procedure and results of controlling the projector with either of
these RCU options is essentially the same.
5(027(
,5
How to use your RCU
a) Point the front of the RCU towards the reflective screen surface
Ceiling
IR sensor
Screen
Plug one end of the remote cable in the connector on the bottom of
the RCU and the second side in the connector in the rear panel of the
projector labelled 'REMOTE'.
d) Built-in RCU (local keypad)
To gain access to the built-in RCU, see paragraph 'The local keypad'
Projector Address
RCU
a. Software set up of the projector address.
b) Point the front of the RCU towards one of the IR sensors in the
projector.
When using the wireless remote control, make sure you are within the
effective operating distance (30m, 100ft in a straight line). The
remote control unit will not function properly if strong light strikes the
sensor window or if there are obstacles between the remote control
unit and the projector's IR sensor.
IR Receiver Locations on the Projector:
See 'Change Projector Address' in chapter 'Service Mode'.
Every projector requires an individual address between 0 and 255
which is set in the Service mode. Only projectors with addresses
between 0 and 9 can be controlled with the RCU.
b. How to control the projector.
The projector's address may be set to any value between 0 and 255.
When the address is set, the projector can be controlled now with :
- the RCU for addresses between 1 and 9.
- computer, e.g. IBM PC (or compatible), Apple MAC, etc. for
addresses between 0 and 255.
Note : a projector will respond to a RCU set to an address of '0'
regardless of what address is set in the projector itself. Address "0"
is therefore a universal address.
c. Using your RCU.
Before using your RCU, it is necessary to enter the projector address
into the RCU (only when that address is between 1 and 9). The
projector with the corresponding address will listen to that specific
RCU.
When address 0, 'zero address' is programmed into the RCU, every
projector, without exception will listen to the commands given by this
RCU.
ADJ
(17(5
MUTE
9
0
7 8
56
34
12
4-2
EXIT
E
X
IT
A
D
J
ADDR
STBY
(17(5
A
D
D
R
STBY
MUTE
TEXT
TEXT
-
+
SHARPNESS
-
+
TINT
-
+
C
O
L
O
R
+
BRIGHTNESS
-
+
CONTRAST
9 0
7 8
56
34
12
-
+
SHARPNESS
-
+
TINT
-
+
COLOR
+
-
B
R
IG
H
TN
ES
S
-
+
CONTRAST
5975688 BARCOVISION 1609S 131097
Controlling
How to display a projector address?
Press the ADDRESS key (recessed key on the RCU) with a pencil.
The projector's address will be displayed in a 'Text box'. This text box
disappears after a few seconds.
With the digit buttons on the RCU, it is possible to select input
sources, Video, S-Video, RGsB or RGBS, RG3sB or RGB3S.
When a valid and available source is selected, there will be information displayed on the screen about that source (if "Text" is on). This
information includes :
-source number
- horizontal frequency
- vertical frequency
PROJECTOR
ADDRESS
001
To continue using your RCU, it is necessary to enter the same
address with the digit buttons (address between 0 and 9). For
exemple, if the Adrress Key displays projector address 003, then
press the "3" digit button on the RCU to set the RCU's address to
match the projector's address.
How to program an address into the RCU?
Source 2
Fh= 15.6 kHz
Fv= 60 Hz
When the entry is a non valid source
number, a warning appears on the screen : 'input not available'.
Press the ADDRESS key (recessed key on the RCU) with a pencil and
enter the address with the digit buttons. That address can be any digit
between 0 and 9.
When programming '0', zero address, the RCU will control a projector
regardless of the projector's address. This feature allows multiple
projectors with different addresses to be controlled by a single RCU.
Input selection
Port No
1
2
3
4
5
*
Projector input
WARNING
input not
available
Press Digit
Button
1
Comp. Video
1
2
S-Video1/Comp. Video*
2
3
RGB2
3
4/5
RGB2
4 or 5
4/5
Component video3
6
4/5
RGB with Tri level sync4
7
4/5
Component video
with Tri-level sync5
8
When a valid source number is selected, the projector will display this
source or it will wait on the selected source number until the source
WARNING
source not
available
becomes available. A message 'source not available' will be displayed for a short time.
Only available when the optional Tri-level sync module is
installed.
Input signal Y/C (luma/chroma)
Input signal : R, G and B with automatic sync detection between
seperate sync (separate composite sync or with separate Hor
and Vert. sync) or sync on green (composite sync).
Input signal : R-Y, Y and B-Y with separate composite sync or
with separate Hor and Vert. sync or with composite sync on Y.
Input signal : R, G and B with separate Tri level sync or with Trilevel sync on green.
Input signal : R-Y, Y and B-Y with separate Tri level sync or with
composite Tri-level sync.
Video or S-Video : switchable in the Picture Tuning menu.
5975688 BARCOVISION 1609S 131097
4-3
Controlling
Analog Picture Controls
The analog picture controls can be adjusted with the RCU. The control keys are
located on the lower right side of the key panel of the RCU and indicated with the name
of the control and an icon.
When an analog picture control is pressed, a text box with bar scale and the function
name of the control, e.g. 'brightness...' appears on the screen (only if 'TEXT' is ON).
The length of the bar scale indicates the current memorized setting for this
source. The bar scale changes as the + or - buttons of the control are pressed.
Brightness Control
BRIGHTNESS
A correct 'brightness' setting is important for good image reproduction. Adjust the
36
brightness with the + button and - button (RCU) until the darkest parts of the picture
appear black.
A bar scale gives a visual indication on the screen of the current brightness setting
while pressing on the above indicated keys. If the bar scale is not visible on the screen, press 'TEXT' key once and retry the above indicated
keys.
The bar scale increases when pressing on the + button (higher brightness) and decreases when pressing on the - button (lower brightness).
Contrast Control
A correct 'contrast' setting is important for good image reproduction.
Adjust the contrast to the level you prefer, according to room lighting conditions. If the Contrast Control is too low, the picture will be too dim.
If it is set too high, the picture may be too bright and not sharp.
A bar scale gives a visual indication on the screen of the current contrast setting while pressing the + or - buttons (RCU). If the bar scale is
not visible on the screen, press 'TEXT' key once and retry the above indicated keys.
The bar scale increases when pressing on the + button (higher contrast) and decreases when pressing on the - button (lower contrast).
Color Saturation Control
Color saturation is only active for Video and S-Video Inputs. This control adjusts the color intensity of the picture. Adjust the color saturation
using the + and - buttons (RCU). A bar scale gives a visual indication on the screen of the current color setting while pressing on the above
indicated keys. If the bar scale is not visible on the screen, press 'TEXT' key once and retry the above indicated keys. The bar scale increases
when pressing on the + button (richer colors) and decreases when pressing the - button (lighter colors).
Tint Control
Tint is only active for Video and S-Video Inputs. The Tint Control is effective only when using the NTSC 4.43 or NTSC 3.58 system. A bar scale
gives a visual indication on the screen of the current tint setting while pressing the + or - buttons (RCU). If the bar scale is not visible on the
screen, press the 'TEXT' key once and retry the above indicated keys buttons.
The bar scale increases when pressing on the + button (greener flesh tones) and decreases when pressing the - button (redder flesh tones).
Sharpness Control.
Sharpness control only active for Video and S-Video Inputs. A bar scale gives a visual indication on the screen of the current sharpness setting
while pressing the + or - buttons (RCU). If the bar scale is not visible on the screen, press 'TEXT' key once and retry the above indicated keys.
The bar scale increases when pressing on the + button (sharper picture) and decreases when pressing on the - button (softer picture).
Controlling chained projectors.
Projectors can be controlled individually as well as in a group.
For individual control see previous pages.
For group control of the projectors.
(input selection and analog picture control)
Program the 'zero address' into any RCU. Therefore, press on the address key and key in the address ("0") with the numeric keys on the RCU
itself.
Once address '0' is pressed, all projectors will be controlled together until a new address is entered on the RCU. It is possible to have a common
input selection and a common analog picture control.
Once a new address is entered, only the projector with that specific address will follow the new instructions.
Note : For group control, all projectors in a control group must be capable of receiving the IR signal from the controlling RCU at the same time.
4-4
5975688 BARCOVISION 1609S 131097
Start Up of the Adjustment Mode
5
START UP OF THE ADJUSTMENT MODE
Adjustment Mode
All picture geometry and convergence adjustments are made while in the 'Adjustment mode'. Press the ADJUST key to enter the 'adjustment
mode'.
You are now in the 'Adjustment mode'. The Control disk is used to make menu selections and also vertical and horizontal adjustments.
The ENTER and EXIT keys are used to move forward and backward through the menu structure. The ADJUST key can be used to terminate
the adjustment mode while any path selection menu is displayed.
When an adjustment menu is displayed on the screen and no action is taken within the first 5 minutes, the projector will automatically reduce
the brightness and contrast to a level so that the stationary image cannot damage the tubes.
There are 5 possible paths to follow once in the Adjustment mode. They are :
INSTALLATION - Installation should be selected if the projector has been relocated
and/or a different screen size is desired.
When selecting 'Installation', the user or operator will be warned to call a qualified
technician to perform the installation procedure (see example of projected warning
on the next page)
GUIDED - Guided should be selected if the user intends to perform a complete
alignment of the projected image. All of the necessary geometry and convergence
adjustments are made in a predetermined sequence.
RANDOM ACCESS - Random Access should be selected if the user intends to make
only a few adjustments.
ADJUSTMENT MODE
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Source 01
Select with
or
then <ENTER>
<EXIT> to return.
SERVICE - Service should be selected if the user intends to delete blocks, change
password , select service adjustments or get set-up information.
IRIS - This selection will only be available when the IRIS Auto-Convergence unit
is connected to the projector. (See Adjustment Manual for IRIS²)
While in Guided or Random Access adjustment Modes, the user may use an external
source, an internally generated genlocked pattern or an internally generated
multifrequency cross hatch pattern as a setup pattern.
Warning during the start up of the installation mode.
WARNING
RISK OF ELECTRICAL SHOCK
NO USER ADJUSTABLE PARTS
INSIDE
THE FOLLOWING INSTALLATION
MENUS ARE RESERVED TO, AND
TO BE PERFORMED ONLY BY
BARCO PERSONNEL, OR BARCO
AUTHORIZED DEALERS
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN
5975688 BARCOVISION 1609S 131097
5-1
Start Up of the Adjustment Mode
Some items in the Adjustment mode are password protected. While selecting such
an item, the projector asks you to enter your password. (Password protection is
only available when the password DIP switch on the controller module is in the ON
position. Contact a BARCO authorized technician when no password is requested
during the adjustment procedure and password protection is desired.)
Your password contains 4 digits.
Enter the digits with the numeric keys on the RCU.
Example : 2 3 1 9
For each digit entered, a 'X' appears on the screen under the displayed text 'enter
password'.
When your password is correct, you get access to the 'Adjustment item'.
When the entered password is wrong, The message 'Wrong password !!!' will be
displayed. The projector stays on the previous selected item.
Factory programmed password :
0000
enter
password
xxxx
wrong
password
!!!
Once the password is correctly entered, all other password protected items are
accessible without re-entering your password.
When re-entering the Adjustment mode, it will be necessary to enter your password
again when selecting a password protected item.
5-2
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
6
RANDOM ACCESS ADJUSTMENT MODE
Starting-Up the Random Access Adjustment mode.
Push the control disk up or down to highlight "RANDOM ACCESS" and then press
ENTER.
Some items in the Random access mode are password protected (when the
password function is enabled). Enter your password to continue. All other
password protected items are now also available if you stay in the adjustment mode.
ENTER continues to Setup Pattern Selection
EXIT returns to Operational mode
ADJUSTMENT MODE
Select a path from below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
Source 01
Select with
or
then <ENTER>
<EXIT> to return.
Overview 'Random Access Adjustment' mode
COLOR BALANCE
SYNC
PEAKING
PICTURE TUNING
CLAMP TUNING
LINE DOUBLER
PORT 2
H PHASE
RANDOM ACCESS
ADJUSTMENT MODE
GEOMETRY
RASTER SHIFT
V CENTERLINE BOW
V CENTERLINE SKEW
LEFT-RIGHT (E-W)
SIDE BOW
SIDE KEYSTONE
SETUP PATTERN SELECTION
SEAGULL CORRECTION
LEFT SIDE CORRECTIONS
LEFT KEYSTONE
LEFT BOW
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP-BOTTOM (N-S)
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
SEAGULL CORRECTION
To next page
5975688 BARCOVISION 1609S 131097
To next page
6-1
Random Access Adjustment Mode
From next page
From next page
H SIZE
V LINEARITY
V SIZE
BLANKING
TOP
BOTTOM
LEFT
RIGHT
GREEN ONLY
RANDOM ACCESS
ADJUSTMENT MODE
CONVERGENCE
RED ON GREEN
BLUE ON GREEN
RED
SETUP PATTERN SELECTION
FOCUSING
GREEN
BLUE
RED
GREEN
COLOR SELECT
BLUE
RED AND GREEN
BLUE AND GREEN
RED AND BLUE
ORBITING
CONTRAST MODULATION
SOFT EDGE CORRECTION
6-2
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Selecting Setup Pattern
If an external source is connected to the projector, this menu will be displayed. Push the control
disk up or down to highlight the desired setup pattern and then press ENTER.
Genlocked pattern : internally generated cross hatch pattern, locked on the external source.
Internal # pattern : internally generated cross hatch pattern and locked on internal generated
sync signals. (No external source necessary)
ENTER continues to Random Access Adjustment Mode or Internal # Pattern Selection
Choose a setup pattern
from below :
SELECTED SOURCE
GENLOCKED PATTERN
INTERNAL # PATTERN
Source 01
Select with
or
then <ENTER>
<EXIT> to return.
EXIT returns to Path Selection menu
ADJUST returns to Operational mode
If no external source is connected to the projector, the internal cross hatch
pattern menu will be displayed.
Note: The menus in this manual are created for an external source, connected to one of
the inputs, and the 'Genlocked Pattern' is selected.
Internal Cross Hatch Pattern
The Internal # pattern menu will be displayed if the internal cross hatch pattern has been
selected or if no source is connected to the projector.
The table below lists the 8 fixed factory preset frequencies available. Another 8 blocks are
custom programmable.
Push the control disk up or down to highlight the desired cross hatch frequency. Push the
control disk to the left and to the right to scroll to another page. Press ENTER if the desired
block is selected.
kHz/Hz
15.6/50
15.7/60
31.2/50
31.5/60
31.2/50
31.5/60
33.7/60
61.0/76
PAL/SECAM
NTSC
EDTV
IDTV
HDTV EUREKA
HDTV ATV
HDTV HIVISION
SUPER VGA 3
INTERNAL # PATTERN
kHz / Hz
15.6/50
15.7/60
31.2/50
31.5/60
31.2/50
31.5/60
PAL/SECAM
NTSC
EDTV
IDTV
HDTV EUREKA
HDTV ATV
Select with
or
scroll with
or
<ENTER> to accept
<EXIT> to return
ENTER continues to the Random Access Adjustment Mode.
EXIT returns to the Setup Pattern Selection menu.
5975688 BARCOVISION 1609S 131097
6-3
Random Access Adjustment Mode
Random access adjustment mode selection menu.
This is the main menu for the Random Access adjustment mode.
Through this menu, the following adjustments and features are accessible :
- Picture Tuning
Enhanced Blue (only for RGB)
Sync slow/fast
Color Balance
- Focusing
- Geometry
- Convergence
- Color select
And also Orbiting, Contrast modulation and Soft Edge if these options are installed.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with
or
then <ENTER>
<EXIT> to return.
Picture Tuning
Highlight Picture tuning by pushing the control disk up or down and press ENTER.
The Picture tuning menu will be displayed.
Depending on the input source, the Picture tuning menu will display different items.
For Video input sources :
Color Balance
Line Doubler
Port 2 : Video or S-Video (only when source 2 is selected)
For RGB analog sources :
Color Balance
Sync slow/fast
Peaking
Clamp Tuning
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING
LINE DOUBLER
Select with
or
<ENTER> to accept
<EXIT> to return.
for Component input and RGB on 15 kHz.
Color Balance
Sync slow/fast
Peaking
Clamp Tuning
Line Doubler (option)
Color Balance
The Color Balance function is used to select or adjust the color
temperature of white used by the projector.
The Color Balance can be adjusted on two different ways :
- fixed color balance. You have the choice between 3200 K (reddish),
4900 K, 6500 K (white) or 9300 K (bluish).
- Custom white and black balance.
Fixed Color Balance.
Highlight one of the 4 preprogrammed color temperatures with the
control disk and press ENTER to display the desired color balance.
Custom Color Balance.
Select custom Red & Blue gain with the control disk and press ENTER
to start the adjustment.
Push the control disk up or down to adjust the red gain and push the
control disk to the left or to the right to adjust the blue gain. A bar scale
indicates the amount of adjustment.
Select custom Green gain with the control disk and press ENTER to
start the adjustment.
Push the control disk up or down to adjust the green gain.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING
LINE DOUBLER
Select with
or
<ENTER> to accept
COLOR BALANCE
<EXIT> to return.
FIXED COLOR BALANCE
3200 4900 6500 9300
CUSTOM RED & BLUE GAIN
CUSTOM GREEN GAIN
CUSTOM RED & BLUE CUT OFF
CUSTOM GREEN CUT OFF
Select with arrow keys
then <ENTER>
Red & Blue :
adjust red with
or
Blue with
or
<EXIT> to return
Select custom R & B cut off with the control disk and press enter to
start the adjustment. Push the control disk up or down to adjust the
red cut-off and push the control disk to the left or to the right to adjust
the blue cut-off.
Select custom Green cut off with the control disk and press enter to
start the adjustment. Push the control disk up or down to adjust the
red cut-off
EXIT returns to the Picture tuning menu.
6-4
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Sync Fast/Slow Adjustment
The sync function is used to minimize horizontal jittering or tearing at
the top to the displayed image.
Highlight SYNC by pushing the control disk up or down and press
ENTER to toggle between FAST and SLOW.
Note: SYNC is normally used in the SLOW position. For Video and
S-Video the sync is automatically set to FAST.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
LINE DOUBLER
Select with
or
<ENTER> to accept
<EXIT> to return.
ENTER will toggle Sync between FAST and SLOW
EXIT will return to the random access selection menu
Peaking
Peaking improves the contours in an projected image.
Highlight PEAKING by pushing the control disk up or down and press
ENTER to display the peaking menu.
During the creation of new settings for a RGB source the corresponding peaking is switched on as default.
For frequencies between :
15 kHz - 45 kHz : Low frequency peaking
45 kHz - 85 kHz : Mid frequency peaking
85 kHz - 135 kHz :High frequency peaking
If another peaking is desired, use the control disk to highlight
'low', 'mid' or 'high' frequency or to switch off the peaking.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
LINE DOUBLER
Select with
or
<ENTER> to accept
<EXIT> to return.
PEAKING
OFF
LOW FREQUENCY
MID FREQUENCY
HIGH FREQUENCY
Select with
or
then <ENTER>
<EXIT> to return.
Clamp Tuning
Highlight CLAMP TUNING by pushing the control disk up or down and
press ENTER to toggle between NORMAL and RESTORATION.
Select Normal : - for all standard sources and all sources with a
backporch > 0.8µs,
- for sources with noise and spikes in the signal.
Select Restoration
: - for standard sources with a backporch between
0.4 µs and 0.8 µs,
- for sources with sync separate or sync on Green.
5975688 BARCOVISION 1609S 131097
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PEAKING
CLAMP TUNING : normal
LINE DOUBLER :ON
Select with
or
<ENTER> to accept
<EXIT> to return.
6-5
Random Access Adjustment Mode
Port 2 : Video or S-Video
Port 2 can be used as a Video or S-Video input.
Highlight Port 2 by pushing the control disk up or down and press
ENTER to toggle between VIDEO and S-VIDEO.
PICTURE TUNING
COLOR BALANCE
PORT2 : S-VIDEO
LINE DOUBLER : ON
Select with
or
<ENTER> to accept
<EXIT> to return.
Line Doubler (option)
Line doubling is only possible for Video, S-Video, Component
Video images on standard line frequency and RGB signals on 15
kHz.
To eliminate the video line patterns and to improve the image
stability, the line doubler has to be switched on. The line doubler
is default set in the ON position when starting up for the first time.
The setting of the line doubler will be saved together with the
source number. Each time this source number is selected, the
last saved version will be loaded.
PICTURE TUNING
COLOR BALANCE
SYNC : FAST
PORT2 : S-VIDEO
LINE DOUBLER : ON
Select with
or
<ENTER> to accept
<EXIT> to return.
Highlight Line Doubler with the control disk and press ENTER to
toggle between ON (active) and OFF (non active).
EXIT will return to the random access selection menu.
Color Select
Highlight COLOR SELECT by pushing the control disk up or down
and press ENTER to display the color select menu.
ENTER continues to the color select menu
EXIT will return to Internal Crosshatch Selection or Setup
Pattern Selection Menu
ADJUST returns to operational mode
Use the control disk to highlight a color (CRT) or combination of colors
to display the projected image in that specific color.
To select a new color, press ENTER, the color selection menu
appears again on the screen. To terminate the color select procedure, press EXIT.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with
or
then <ENTER>
<EXIT> to return.
COLOR SELECT
RED
GREEN
BLUE
RED AND GREEN
BLUE AND GREEN
RED AND BLUE
Select with
or
<ENTER> to accept
<EXIT> to return.
ENTER continues with the selected color or color combination.
EXIT returns to the Random access main menu.
6-6
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Focusing
Before starting the 'focusing' adjustment, be sure the lenses are
correctly focused.
Push the control disk up or down to select 'Focusing' and press
ENTER.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
ENTER continues to the Focusing color select menu.
EXIT returns to Internal Crosshatch Selection or Setup Pattern
Selection menu.
ADJUST returns to operational mode.
Select with
or
then <ENTER>
<EXIT> to return.
FOCUSING
RED
GREEN
BLUE
Focusing color select.
BLUE ON SOURCE
The focusing has to be done for the three colors separately.
Therefore, start by selecting Green by pushing the control disk up
or down and adjust Midpoint, top, bottom left and right focusing.
Return to this focusing color select menu and continue with Red and
Blue. Repeat for both colors Midpoint, top, bottom left and right
focusing.
Select with
or
then <ENTER>
<EXIT> to return.
ENTER selects the focusing menu for the selected color.
EXIT returns to the Random access main menu.
Midpoint focusing
Push the control disk up or down to select midpoint and press ENTER
continue with the midpoint focusing.
FOCUSING
Adjust by pushing the control disk to the left or to the right until the
center of the image is sharp.
Press ENTER to return to the focusing menu.
RED
GREEN
BLUE
BLUE ON SOURCE
Top image focusing
Select with
or
then <ENTER>
GREEN FOCUSING
<EXIT> to return.
The same procedure has to be repeated as for the midpoint focusing.
Push the control disk up or down and press ENTER to continue to the
top focusing.
Push the control disk to the left or to the right to adjust the top focusing.
Adjust until the upper part of the image is sharp.
ENTER to return to the Green Focusing menu.
MIDPOINT
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
Bottom image focusing
The same procedure has to be repeated as for the midpoint focusing.
Push the control disk up or down to select bottom and press ENTER
to continue to the bottom focusing.
Push the control disk up or down to adjust the bottom focusing. Adjust
until the lower part of the image is sharp.
ENTER to return to the Green Focusing menu.
Left image focusing
The same procedure has to be repeated as for the midpoint focusing.
Push the control disk up or down to select LEFT and press ENTER
to continue to the left focusing.
Push the control disk up or down to adjust the left focusing. Adjust
until the left part of the image is sharp.
ENTER to return to the Green Focusing menu.
Right image focusing
The same procedure has to be repeated as for the midpoint focusing.
Push the control disk up or down to select RIGHT and press ENTER
to continue to the right focusing.
Push the control disk to the left or to the right to adjust the right
focusing. Adjust until the right part of the image is sharp.
ENTER to return to the Green Focusing menu.
5975688 BARCOVISION 1609S 131097
When on the Green Focusing menu, press EXIT to return to the
focusing color select menu and continue with the other colors.
Blue on source
After focusing the three color, and a discoloring on a normal image
is still visible, select 'Blue on source' on the Focusing menu and repeat
the above steps for Midpoint, top, bottom left and right focusing.
Press EXIT to return to focusing menu.
6-7
Random Access Adjustment Mode
Geometry Adjustments
The geometry adjustments have to be done only on the green image. These adjustments are automatically implemented for the other color
images : Left-right (EW) and Top-Bottom Corrections, Blanking, Horizontal Amplitude, Vertical Amplitude, Vertical Linearity and Horizontal
Phase.
Highlight GEOMETRY by pushing the control disk up or down and
press ENTER to display the geometry menu.
ENTER will display Geometry menu
EXIT will return to Internal Crosshatch Selection or Setup
Pattern Selection Menu
ADJUST returns to operational mode
Within the Geometry Adjustment menu, the following adjustments are
available :
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with
or
then <ENTER>
<EXIT> to return.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
- Horizontal Phase (not for internal # pattern).
- Raster Shift
- Left-Right Corrections
- Left Side Corrections
- Top-Bottom Corrections
- Horizontal Size
- Vertical Linearity
- Vertical Size
- Blanking
Select with
or
then <ENTER>
<EXIT> to return.
The convergence corrections are disabled during geometry corrections. The blanking corrections are only enabled during the blanking
adjustments.
Horizontal Phase Adjustment
GEOMETRY
Push the control disk up or down to highlight H PHASE on Geometry
menu and then press ENTER.
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with
or
then <ENTER>
<EXIT> to return.
Note : No horizontal phase adjustment is available on the internal #
pattern.
For external sources :
If the raster shift is correctly adjusted, the H Phase text box is
projected in the middle of the raster. At that moment, the "><" icon
indicates the middle of the raster.
Adjust the H Phase control until the middle of the projected image is
equal with the middle of >< icon.
Note :
- if the genlocked pattern was selected, the external source will be
displayed.
A bar scale and a number indicator (between 0 and 100) on the
screen give a visual indication of the horizontal phase adjustment.
><
H PHASE
70
Push the control disk to
the right to correct
><
H PHASE
ENTER continues to geometry menu .
70
Push the control disk to
the left to correct
><
H PHASE
70
6-8
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Raster Shift Adjustment
The green raster must be centered both horizontally and vertically on
the center of the CRT surface. To center the green raster, look into
the green lens and use the control disk to move the raster.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
CAUTION
It is necessary to look into the lenses to perform these adjustments.
To avoid eye discomfort while looking into the lenses, reduce the
contrast and gradually increase the brightness level until the raster
becomes visible on the face of the CRT.
ENTER will select green raster shift adjustment
EXIT returns to random access adjustment mode menu.
Warning : In order to ensure maximum CRT longevity and
to avoid CRT damage, do not shift the raster outside the
phosphor area of the CRT.
To start the adjustment, use the control disk to highlight Raster shift
and press ENTER to display the green raster on the phosphor.
Select with
or
then <ENTER>
<EXIT> to return.
forbidden area
projected raster
crt faceplate border
phosphor border
correct raster position
wrong raster position
Press EXIT to return to the Geometry menu.
Note : Horizontal and Vertical shifts for Red and Blue should
be end up with a setting close to 50%. If these settings are
significantly greater or lesser than 50%, then contact a
BARCO authorized service technician.
5975688 BARCOVISION 1609S 131097
6-9
Random Access Adjustment Mode
Left-Right (east-west) Adjustments
Left-right adjustments affect only the vertical lines of the projected
image. Only the green image is displayed while making left-right
adjustments. The red and blue images will automatically be corrected
in the same manner. Convergence corrections are automatically
disabled for the duration of these adjustments.
The following adjustments can be executed
-
Vertical Centerline Bow
Vertical Centerline Skew
Side Bow
Side Keystone
Seagull correction
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with
or
then <ENTER>
<EXIT> to return. LEFT-RIGHT
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION
Push the control disk up or down to highlight LEFT-RIGHT (E/W) on
the geometry menu and then press ENTER.
ENTER will select Left-Right adjustment menu
EXIT returns to random access adjustment mode main menu.
ADJUST returns to operational mode
Warning : Use this correction to
adjust the right side of the image !
Select with
or
then <ENTER>
<EXIT> to return.
The warning : "Use this correction to adjust the right side of the image"
appears on the screen when selecting 'Side Bow' or 'Side Keystone'.
When the right side is correctly adjusted, use 'Left Side Correction'
to correct the left side of the image.
All adjustments are indicated on the screen with the function name,
a bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines are straight. For side
bow and side keystone, look only to the right side of the image.
To enter an alignment, push the control disk up or down to highlight
a function and press ENTER to activate this function.
Press EXIT to return.
Corrects for curvature of the vertical lines in the middle of
the image.
LEFT-RIGHT
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION
Corrects the tilting of the vertical lines in the middle of the
image.
Select with
or
then <ENTER>
<EXIT> to return.
Corrects for curvature of the vertical lines on the right side
Corrects the keystone geometry correction of the vert. lines on
the right side
Correct by pushing
the control disk to the
right
6-10
Correct by pushing
the control disk to the
left
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Seagull correction
Use this correction only if, after adjusting the vertical lines with the
side bow or side keystone, still a 'S' deformation is visible on the left
and the right side of the image.
The default value on the bar scale for this correction is 50.
Push the control disk up or down to highlight SEAGULL CORRECTION on the Left-Right menu and then press ENTER.
Eliminate the deformation by pushing the control disk to the left or to
the right until a straight line is obtained.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with
or
then <ENTER>
<EXIT> to return. LEFT-RIGHT
V CENTERLINE BOW
V CENTERLINE SKEW
SIDE BOW
SIDE KEYSTONE
SEAGULL CORRECTION
Select with
or
then <ENTER>
<EXIT> to return.
Left Side Correction
Left side corrections affect only the vertical lines of the set up pattern.
Only the green image is displayed while making the left side adjustments. The red and blue images will automatically be corrected in the
same manner.
Convergence corrections are automatically disabled for the duration
of these adjustments.
Look only to the left side of the image while adjusting these fine tunings
(bow and keystone). Before starting the left side correction, insure
that the side bow and keystone adjustments are done prior to these
fine adjustments !
The following adjustments can be executed :
- Left keystone
- Left bow
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with
or
then <ENTER>
<EXIT> to return.
LEFT SIDE CORRECTION
LEFT KEYSTONE
LEFT BOW
Ensure that the side bow and
keystone adjustments are done
prior to these fine adjustments
!
Push the control disk up or down to highlight LEFT SIDE CORRECTION on the geometry menu and then press ENTER.
Select with
or
then <ENTER>
<EXIT> to return.
ENTER will select the Left Side Correction menu.
EXIT will return to the random access adjustment menu.
ADJUST returns to operational mode.
All adjustments are indicated on the screen with the function name,
a bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines on the left side are
straight.
LEFT SIDE CORRECTION
LEFT KEYSTONE
LEFT BOW
Ensure that the side bow and
keystone adjustments are done
prior to these fine adjustments
!
Correct the keystone geometry distortion of the
vertical lines
Select with
or
then <ENTER>
<EXIT> to return.
To enter an alignment, push the control disk up or down to highlight
a function and press ENTER to activate this function.
Press EXIT to return.
Correct the bow geometry distortion of the
vertical lines
Correct by pushing
the control disk to the
right
5975688 BARCOVISION 1609S 131097
Correct by pushing
the control disk to the
left
6-11
Random Access Adjustment Mode
Top-Bottom (north-south) Adjustments
Top-Bottom and center adjustments affect only the horizontal lines
of the projected image.
To start up the Top-Bottom and center corrections, follow the next
procedure :
Push the control disk up or down to highlight TOP-BOTTOM (N/S)
on the geometry menu and then press ENTER.
Only the green image is displayed while making top-botton adjustments. The red and blue images will automatically be corrected in
the same manner. Convergence corrections are automatically
disabled for the duration of these adjustments.
The following adjustments can be executed :
-
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with
or
then <ENTER>
<EXIT> to return.
TOP-BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
SEAGULL CORRECTION
Select with
or
then <ENTER>
<EXIT> to return.
horizontal centerline bow
horizontal centerline skew
top bow
top keystone
bottom bow
bottom keystone
seagull correction
All adjustment are indicated on the screen with the function name,
a bar scale and a number between 0 and 100.
Adjust the next alignments until the vertical lines are straight.
To enter an alignment, push the control disk up or down to highlight
a function and press ENTER to activate this function.
Press EXIT to return.
Corrects for curvature of the horizontal lines in the middle
of the image.
Corrects the tilting of the horizontal lines in the middle of
the image.
TOP-BOTTOM
H CENTERLINE BOW
H CENTERLINE SKEW
TOP BOW
TOP KEYSTONE
BOTTOM BOW
BOTTOM KEYSTONE
SEAGULL CORRECTION
Corrects for curvature of the horizontal lines on the upper side
Select with
or
then <ENTER>
<EXIT> to return.
Corrects the keystone geometry correction of the hor. lines on
the upper side
Corrects for curvature of the horizontal lines on the lower side
Corrects the keystone geometry correction of the hor. lines on
the lower side
Correct by pushing
the control disk down
6-12
Correct by pushing
the control disk up
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Seagull Correction
Use this correction after the image has been adjusted with top and
bottom bow and keystone. If still a deformation (like a seagull) on top
and bottom of the image is visible, proceed to the seagull correction.
Due to interaction, it is possible that the top and bottom bow have to
be readjusted after adjusting the seagull correction to obtain an
improved image. The default value on the bar scale of this correction
is 50.
Push the control disk up or down to select the 'Seagull Correction' and
press ENTER to select.
Eliminate teh deformation by pushing the control disk upwards or
downwards until a straight line is obtained.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
Select with
or
then <ENTER>
<EXIT> to return.
TOP-BOTTOM (N-S)
H CENTERLINE BOW
H CENTERLINE SKEW
TOP KEYSTONE
TOP BOW
BOTTOM KEYSTONE
BOTTOM BOW
SEAGULL CORRECTION
ENTER will return to Top-Bottom adjustment menu EXIT will return to
Geometry menu
Select with
or
then <ENTER>
<EXIT> to return.
Horizontal Size Adjustment
Push the control disk up or down to highlight H SIZE on the Geometry
menu and then press ENTER.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
ENTER will select horizontal size adjustment
EXIT returns to random access adjustment mode menu.
ADJUST returns to operational mode
Adjust the horizontal size by the control disk to the right or to the left
until the exact image width is obtained.
Select with
or
then <ENTER>
<EXIT> to return.
Note :
- if the internal # pattern was selected, this pattern remains on the
screen.
- if the genlocked pattern was selected, the external source will be
displayed.
A bar scale and a numeric indicator help to gauge the horizontal size
adjustment.
H SIZE
70
Hint : In order to avoid loss of resolution in the projected image and
to ensure maximum CRT longevity, do not use an excessively small
horizontal size setting.
H size too
large
EXIT will return to Geometry
Ideal image width
H size too
small
5975688 BARCOVISION 1609S 131097
6-13
Random Access Adjustment Mode
Vertical Linearity Adjustment
The vertical linearity adjustment function corrects for vertical nonlinearities which extend from the center of the image to the top and
bottom of the image.
Push the control disk up or down to highlight V LINEARITY on the
Geometry menu and then press ENTER.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
ENTER will select vertical linearity adjustment,
EXIT returns to random access adjustment mode menu,
ADJUST returns to operational mode
Select with
or
then <ENTER>
<EXIT> to return.
Adjust the vertical linearity with the control disk until the distances
between the horizontal lines of the set up pattern are equal from top
to bottom.
EXIT will return to the Geometry menu
V LINEARITY
70
Vertical Size Adjustment
Push the control disk up or down to highlight V SIZE on the Geometry
menu and then press ENTER.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
ENTER will select vertical size adjustment
EXIT returns to random access adjustment mode menu,.
ADJUST returns to operational mode
Adjust the vertical size by pushing the control disk up or down until
the correct image height is obtained.
Select with
or
then <ENTER>
<EXIT> to return.
Note :
- if the internal # pattern was selected, this pattern remains on the
screen.
- if the genlocked pattern was selected, the external source will be
displayed.
V SIZE
A bar scale and a numeric indicator give a visual indication of the
vertical size adjustment.
70
Hint : In order to avoid loss of resolution in the projected image and
to ensure maximum CRT longevity, do not use an excessively small
vertical size setting.
EXIT will return to Geometry
Ideal
Image
Hight
6-14
Image too
Tall
Ideal
Image
Hight
Image too
Short
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Blanking Adjustments
Blanking adjustments affect only the edges of the projected image
and are used to frame the projected image on to the screen and to
hide or black out unwanted information (or noise). A 0% on the bar
scale indicates no blanking.
GEOMETRY
H PHASE
RASTER SHIFT
LEFT-RIGHT (E-W)
LEFT SIDE CORRECTION
TOP-BOTTOM (N-S)
H SIZE
V LINEARITY
V SIZE
BLANKING
To start up the Blanking adjustments, follow the next procedure :
Push the control disk up or down to highlight BLANKING on the
Geometry menu and then press ENTER.
Select with
or
then <ENTER>
<EXIT> to return.
BLANKING
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
The following blanking corrections are possible :
- top blanking
- bottom blanking
- left blanking
- right blanking
Top blanking
Right blanking
Left blanking
Therefore :
- if the internal # pattern was selected, this pattern remains on the
screen.
- if the genlocked pattern was selected, the external source
will be displayed.
Bottom blanking
Adjust the next blanking alignments until the image is correctly framed
or the unwanted information is blanked out.
To enter a blanking alignment, push the control disk up or down to
highlight a function and press ENTER to activate this function.
Press EXIT to return.
Adjustment of the blanking on the of the image
BLANKING
TOP
BOTTOM
LEFT
RIGHT
Select with
or
then <ENTER>
<EXIT> to return.
Adjustment of the blanking on the bottom of the image
Correct by pushing the control disk up or
down
Adjustment of the blanking on the left side
Adjustment of the blanking on the right side
Correct by pushing the control disk to the
right or to the left
5975688 BARCOVISION 1609S 131097
6-15
Random Access Adjustment Mode
Convergence Adjustment
Convergence adjustments affect both the horizontal and vertical
lines of the setup pattern. These adjustments are performed on the
red image while superimposed on the green image and then on the
blue image while superimposed on the green image.
Start with the Coarse convergence adjustments and finalise with the
Fine convergence adjustment.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with
or
then <ENTER>
<EXIT> to CONVERGENCE
return.
COARSE ADJUSTMENT
RED ON GREEN
BLUE ON GREEN
FINE ADJUSTMENT
GREEN ONLY
RED ON GREEN
BLUE ON GREEN
Select with
or
then <ENTER>
<EXIT> to return.
The screen area is divided into 25 areas.
25
23
9
15
17
24
22
8
14
16
5
4
1
2
3
20
18
6
10
12
21
19
7
11
13
Coarse Convergence Adjustment.
Highlight 'Red on green' under the coarse convergence item and
press ENTER. The coarse convergence menu will be displayed.
The following items are possible :
- Horizontal sides : adjust the vertical lines, within a certain area,
on both sides without influencing the lines on the middle of the
image.
- Vertical corners : adjust the horizontal lines in the four corners,
within a certain area, without influencing the middle of the image.
Repeat for 'blue on green'
Select with
or
then <ENTER>
<EXIT> to CONVERGENCE
return.
COARSE ADJUSTMENT
RED ON GREEN
BLUE ON GREEN
FINE ADJUSTMENT
GREEN ONLY
RED ON GREEN
BLUE ON GREEN
or
Select Select
with withor
then <ENTER>
then <ENTER>
to
return.
<EXIT><EXIT>
to return.
COARSE CONVERGENCE
HORIZONTAL SIDES
VERTICAL CORNERS
Select with
or
then <ENTER>
<EXIT> to return.
Horizontal sides
Highlight 'Horizontal lines' and press ENTER to start the adjustment.
To make a coarse adjustment of the red or blue vertical lines in zone
3 and 5 simultaneously.
B G
R
B
G
R
Hint :
- look to the end of scan and adjust until the red or the blue vertical
lines are on the green lines or as close as possible to the green lines.
- during these adjustments, the horizontal convergence adjustments
in zones 2, 3, 4 and 5 will be set to midposition (barscale 50).
6-16
Select with
or
then <ENTER>
<EXIT>
to
return.
COARSE CONVERGENCE
HORIZONTAL SIDES
VERTICAL CORNERS
Select with
or
then <ENTER>
<EXIT> to return.
5975688 BARCOVISION 1609S 131097
Random Access Adjustment Mode
Vertical corners
Highlight 'Vertical corners' and press ENTER to start the adjustment.
To make a coarse adjustment of the red or blue horizontal lines in zone
10, 14, 18 and 22 simultaneously.
Select with
or
then <ENTER>
<EXIT>
to
return.
COARSE CONVERGENCE
HORIZONTAL SIDES
VERTICAL CORNERS
Select with
or
then <ENTER>
<EXIT> to return.
Hint :
- Adjust until the red or the blue horizontal lines are on the green lines
or as close as possible to the green lines.
- During these adjustments, the horizontal convergence adjustments
in zones 10 to 25 will be set to midposition (barscale 50).
Fine Convergence Adjustment.
Use these controls after coarse convergence adjustment to optimize
the convergence of the red and blue image on the green image.
Use the control disk to make horizontal or vertical convergence
adjustments in the selected zone and then press ENTER to move the
box to another zone or EXIT to return to the Convergence menu.
ENTER toggles arrow keys between zone selection and zone
adjustment .
EXIT returns to convergence menu.
Note : The green convergence adjustments can be added as an
option. When these are available, always start with 'green only'. This
option will also be indicated on the convergence menu.
Select with
or
then <ENTER>
<EXIT> to CONVERGENCE
return.
COARSE ADJUSTMENT
RED ON GREEN
BLUE ON GREEN
FINE ADJUSTMENT
GREEN ONLY
RED ON GREEN
BLUE ON GREEN
Select with
or
then <ENTER>
<EXIT> to return.
CONVERGENCE
SEL : select area
using
arrow keys
ADJ : adjust area
using
arrow keys
Toggle between
SEL and ADJ
with <ENTER>
<ENTER> continue
<EXIT> to return
Highlight first 'Green only' when available with the control disk and
press ENTER to display the convergence adjustment menu.
Continue with red on green and blue on green.
CONVERGE
ADJUSTMENT
70
green image
red image
5975688 BARCOVISION 1609S 131097
6-17
Random Access Adjustment Mode
6-18
5975688 BARCOVISION 1609S 131097
Service Mode
7
SERVICE MODE
Starting up the Service mode.
Use the control disk to highlight 'Service' and then press ENTER.
Some items in the Service mode are password protected (when the
password function is active). Enter your password to continue. All
other password protected items are now also free available if you
stay in the adjustment mode.
ENTER continues to the Service Mode main menu.
EXIT returns to the Operational mode.
The service items are combined in two service menus. To switch
from the first to the second menu or vice versa, push the control disk
up or down to select 'more...'
ADJUSTMENT MODE
Select a path from
below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
Select with
or
then <ENTER>
<EXIT> to return.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
Overview flowchart 'Service' mode.
Select with
or
then <ENTER>
<EXIT> to return.
IDENTIFICATION
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
SERVICE MODE
RUN TIME
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
5975688 BARCOVISION 1609s 131097
7-1
Service Mode
Identification
Highlight 'Identification' with the control disk and press ENTER.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
The 'Identification' screen gives information concerning :
- projector address. To change the address of your projector,
contact a qualified service technician.
- software version.
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
- configuration.
possible installations :
* front-ceiling
* front-table
* rear-ceiling
* rear-table
VISION 1609s
Proj. address : 001
Soft. Version : 6.00
Config. : Ceiling
Front
Baudrate PC : 9600
Text : ON
Serial No. : 103589552
- baud rate PC : transfer speed for communication with an IBM PC
(or compatible) or MAC. The baud rate of the projector must be the
same as the baud rate of the connected computer. When there is a
difference, contact a qualified service
technician to make the appropriate changes.
- Text ON/OFF
Indicates in operational mode if the bar scale and number indicator
will be displayed and if warnings and failures will be displayed.
ON : displayed
OFF : not displayed
The status can be changed by pressing the 'TEXT' key once on
the
RCU.
- Serial no. : indicates the fabrication number of the projector. This
number can be useful when calling for technical assistance.
Copy a block
The copy a block function copies the settings of a selected block into
the active block.
Highlight copy a block with the control disk and press ENTER.
ENTER will select the highlighted item.
To copy the settings of a closed block to the block you are working
on (active block), use the control disk to select a block.
All existing settings will be overwritten with the new settings.
Press ENTER to copy the selected block. A confirmation screen will
be displayed.
If you are certain you wish to copy the contents of the selected block
into the active block, press ENTER.
EXIT cancels the copy procedure and returns without copying the
block.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
Nr. Src
1
1
2
3
3
4
2
5
6
7
8
1
COPY MODE
Fh Fv
inp
15.6 50
video
31.2 60
RGB3S
15.6 50
intern
31.5 50
RGB3S
33.7 60
intern
conf
FC
RT
FC
FC
FC
Active block nr.
Select with
or
<ENTER> to copy
<EXIT> to return.
COPY BLOCK
All settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
7-2
5975688 BARCOVISION 1609s 131097
Service Mode
Deletion of blocks
This item is password protected.
The delete function is used to clear all data (settings) from an
adjustment block.
A delete can be given :
- block by block
or
- for all blocks.
Deleting block by block
The delete a block function deletes the settings of a selected block.
Highlight 'Delete a block' with the control disk and press ENTER.
Push the control disk up or down to select the desired adjustment
block. Press ENTER to delete the selected adjustment block. A
confirmation menu will be displayed.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
DELETE
Nr. Src Fh Fv
1
1
15.6 50
2
3
31.2 60
3
15.6 50
4
2
31.5 50
5
33.7 60
6
7
8
1
ENTER will delete the selected block.
EXIT cancels the deletion procedure and returns to the Service mode
main menu.
MODE
inp
video
RGB3S
intern
RGB3S
intern
conf
FC
RT
FC
FC
FC
Active block nr.
Select with
or
<ENTER> to copy
<EXIT> to return.
DELETE BLOCK
The selected block
will be deleted !
<ENTER> to confirm
<EXIT> to cancel
Deletion of all blocks
Highlight 'delete all blocks' with the control disk and press ENTER.
ENTER gives a confirmation message before deleting.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
If you are certain you wish to delete all blocks, press ENTER to
confirm, otherwise press EXIT to return.
Once ENTER is pressed, all block headers and adjustment settings
are permanently removed and cannot be restored.
Select with
or
then <ENTER>
<EXIT> to return. DELETE BLOCK
All block
will be deleted !
<ENTER> to confirm
<EXIT> to cancel
5975688 BARCOVISION 1609s 131097
7-3
Service Mode
Change password
This item is password protected.
Highlight 'change password' with the control disk and press ENTER.
The current password is displayed. The new password must
consist of 4 digits between 0 and 9. Push the control disk to the left
or to the right to select the digits to be changed. Use the numeric keys
to enter the new digits.
Press ENTER to save the new password. Before saving the new
password, a confirmation screen will be displayed.
Press EXIT to return to the Service menu without saving the new
password.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
PASSWORD
Enter new password :
0000
When the displayed password is correct, press ENTER to save.
If not correct, press EXIT to cancel the saving.
Use
and
to select,
and reprogram
with numeric keys.
<ENTER> to confirm
<EXIT> to return
CHANGE PASSWORD
Password will be
reprogrammed as xxxx
<ENTER> to confirm
<EXIT> to cancel
Change Language
The 'Change Language' function offers the possibility to change the
language of the screen menus to :
- English
- Spanish
- French
- German
therefore, pusj the control disk up or down to highlight 'Change
language' and press ENTER to select the language menu.
Push the control disk up or down to select the desired language and
press ENTER to change the language.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
LANGUAGE
ENGLISH
ESPAÑOL
FRANCAIS
DEUTSCH
Select new language
with
or
then <ENTER>
<EXIT> to return.
Run time
Highlight 'run time' with the control disk and press ENTER to display
the amount of time the projector has played since its first start up at
the factory.
Note : all projectors leave the factory after a burn-in period of
approximately 100 hours.
Press EXIT to return the service mode menu.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
RUN TIME
105 h
7-4
5975688 BARCOVISION 1609s 131097
Service Mode
Set to midposition
Item is password protected.
Highlight 'set to midposition' with the control disk and press ENTER
to set all settings to their midposition.
A confirmation menu will be displayed first.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
ENTER will set all settings to their midposition. EXIT will cancel the
operation to set all settings to their midposition.
Select with
or
then <ENTER>
<EXIT> to return.
SET TO MIDPOSITION
All settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
Undo Midposition
When 'Set to Midposition' is selected, all settings are set to their
midposition. To cancel this action, select 'Undo Midposition' by
pushing the control disk up or down and press ENTER. 'Undo
Midposition' is displayed in the service mode in stead off 'Set to
Midposition' when this latter is pressed.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
UNDO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
An undo is possible as long as the projector is playing on the same
source (= same adjustment block) even when some adjustments as
geometry or convergence are already readjusted. When undo is
pressed all settings are reset to the previous settings.
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
Convergence Mid
Item is password protected.
Highlight 'convergence mid' with the control disk and press ENTER
to set all convergence settings to their midposition. A confirmation
screen will be displayed first.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
ENTER sets the convergence settings to their midposition. EXIT
cancels the procedure to set the convergence settings to their
midposition.
Select with
or
then <ENTER>
<EXIT> to return. CONVERGENCE MID
All settings
in current block
will be overwritten !
<ENTER> to confirm
<EXIT> to cancel
Undo Convergence Mid(position)
When 'Convergence Mid' is activated, all convergence settings are
set to their midposition. To cancel this action, select 'Undo Convergence Mid' by pushing the control disk up or down and press ENTER.
'Undo Convergence Mid' is displayed in the service mode menu in
stead off 'Convergence Mid' when this latter is activated.
An 'undo' is possible :
* as long as the projector is operating on the same source (= same
adjustment block) even when some convergence adjustments are
already readjusted
AND
* 'set to midposition' is not yet selected.
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
UNDO CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
When undo is pressed all convergence settings are reset to the
previous settings.
5975688 BARCOVISION 1609s 131097
7-5
Service Mode
Dynamic Astigmatism (spot shape adjustment)
The spot shape adjustments correct the spot shape in 8 different
areas on the screen and that for the three colors separately.
The spot shape is adjusted according to the axial axises and the
diagonal axises when using the arrow keys on the RCU.
These adjustments have to be done on a dot pattern (e.g. the internally
generated pattern) with standard line frequency (15 kHz). The
adjustment values are stored in the EEPROM and remain the same for
all frequencies.
Follow the next procedure :
Highlight 'Dyn. Astigmatism' by pushing the joy disk up or down and
press ENTER to select.
EXIT returns to the path selection main menu.
Spot shapes
before dynamic
astigmatism correction
Diagonal
astigmatism correction
(use the
and
arrow key)
Spot shapes
after dynamic
astigmatism correction
Axial
astigmatism correction
(use the
and
arrow key)
Select the source type, selected source or genlock pattern, by
highlighting the color for which the spot shape has to be corrected
and press ENTER.
e.g. when selecting RED under 'on genlocked pattern', the projector
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
switches to a genlocked pattern.
Press ENTER to continue adjustment.
Increase the contrast level using the Contrast Control to near
maximum. Using that "+" Sharpness Key, defocus the image until the
dots are large and easily visible. Press ENTER to continue to SEL.
Select with
or
then <ENTER>
DYNAMIC ASTIGMATISM
<EXIT> to return.
ON SELECTED SOURCE
RED
GREEN
BLUE
ON GENLOCKED PATTERN
RED
GREEN
BLUE
Select pattern or color
with
or
then <ENTER>
<EXIT> to return.
SEL : select the adjustment area on the screen where the spot shape
has to be corrected.
Use the arrow keys to select one of the 8 areas. Press ENTER to
continue to ADJ.
ADJ : adjust the spot shape in the axial or diagonal direction when
using the arrow keys for the selected area. Adjust until the spot
shape is circular.
Use the up and down arrow keys for the diagonal astigmatism
adjustment and the left and right arrow keys for the axial astigmatism
adjustment. Press ENTER to continue selecting a new area.
The adjustment direction (axial or diagonal) and adjustment value are
7-6
DYNAMIC ASTIGMATISM
First adjust the defocusing
of the image.
SEL : select area using arrow
keys
ADJ : adjust axial astigmatism
using
or
, diagonal
astigmatism using
or
Toggle between SEL and ADJ
with <ENTER>
<ENTER> to continue
<EXIT> to return.
5975688 BARCOVISION 1609s 131097
Service Mode
given in a text box on the screen. When all areas are adjusted, press
EXIT to return to the service main menu.
G2 Adjust
Item is password protected.
Highlight 'G2 adjust' with the control disk and press ENTER to
continue.
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
A safety notice will be displayed on the screen as it is necessary to
open the top cover to adjust the G2.
'G2 adjustment should be performed by BARCO personnel,
or BARCO authorized dealers'.
If you are qualified, press ENTER to continue. If not qualified, press
EXIT to return to the Service mode main menu. Further description
of the G2 adjustment is given in the Installation manual.
Select with
or
then <ENTER>
<EXIT> to return.
SAFETY
NOTICE
RISK OF ELECTRICAL SHOCK
G2 ADJUSTMENT SHOULD BE
PERFORMED BY BARCO
PERSONNEL, OR BARCO
IF QUALIFIED, PRESS
<ENTER> TO CONTINUE, OR
IF NOT, <EXIT> TO RETURN.
Gamma corrections
Item is password protected.
Highlight 'Gamma Corrections' with the control disk and press ENTER
to continue.
A warning will be displayed on the screen as there is a risk of
incorrect adjustment of the projector..
'The Gamma Corrections are factory adjusted using an
ACTAS colour analyser !
Therefore, only qualified installation or service personnel
should perform these adjustments !'
If you are qualified, press ENTER to continue. If not qualified, press
EXIT to return to the Service mode main menu. Further description
of the Gamma Corrections are given in the Installation manual,
Appendix C.
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
Select with
or
then <ENTER>
<EXIT> to return.
WARNING
RISK OF INCORRECT
ADJUSTMENT OF THE PROJECTOR
THE GAMMA CORRECTIONS ARE
FACTORY ADJUSTED USING AN
ACTAS COLOUR ANALYSER !
THEREFORE, ONLY QUALIFIED
INSTALLTION OR SERVICE
PERSONNEL SHOULD PERFORM
THESE ADJUSTMENTS !
<ENTER> TO CONTINUE
<EXIT> TO RETURN.
CRT run in cycle
The CRT run in cycle option can only be activated when memory
blocks on an internal # pattern are available. When one or more such
blocks are available, a flashing white image (5sec on, 5 sec off) is
generated and that for 5 min on the first internal block. In the next 5
min, a second internal block will be used to generate the flashing white
image. The image will also be shifted in a vertical way to prevent a
CRT burn in. To quit the CRT run in cycle option, press EXIT.
Highlight 'CRT run in cycle' with the control disk and press ENTER
to start .
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
Select with
or
then <ENTER>
<EXIT> to return. CRT RUN IN CYCLE
A flashing white pattern will be
generated until <EXIT> is pressed.
If a memory block adjusted on an internal # pattern is available, the
CRT run in cycle will start when pressing ENTER. If no such a block
is available, the projector cannot run the CRT run in option and leaves
the adjustment mode.
If you still want to run CRT run in cycle, create first a memory block
on an internal # pattern and restart the CRT run in option.
5975688 BARCOVISION 1609s 131097
The projector only uses memory
blocks adjusted on an internal
# pattern; if no such block is
available, the projector can't run
the procedure and leaves the
adjusment mode.
<ENTER> to continue
<EXIT> to cancel
7-7
Service Mode
Projector Warm Up
Highlight 'Projector Warm Up' by pushing the control disk up or down
and press ENTER to select the projector warm up menu.
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
The ON/OFF option can be toggled with the ENTER key.
Select with
or
then <ENTER>
<EXIT> to return.
PROJECTOR WARM UP
When in the ON position (and the CRT run in cycle is OFF), the projector
can start up with a warm up period of 20 minutes. During the start
up a warm up menu will displayed. This menu offers the possibility
to skip the warm up periode anyway by pressing the EXIT key and
offers the possibility to adjust the horizontal and vertical amplitude of
the this white image with the control disk. During this warm up period,
a full white image is shifted on the CRT faceplate to avoid a burn in.
Every 30 seconds a text box will be displayed on another place on
the screen with the remaining time to go.
When EXIT is pressed during this warm up periode, the warm up menu
will be redisplayed with the remaining time indication. Press another
time EXIT to interrupt the warm up cycle.
When the warm up option is OFF, when switching on the the
projector, it starts immediately with the projection of the selected
source.
OPTION : ON
A FULL WHITE PATTERN
WILL BE GENERATED FOR
20 MINUTES AT POWER UP
AFTER THIS PROCEDURE
THE PROJECTOR IS READY
TO PERFORM IN OPTIMUM
CONDITION
TOGGLE OPTION ON OR OFF
with <ENTER>
<EXIT> to return
CRT Drive Mode
The projector CRT's can be driven with the normal current (normal
mode), a lower current (economic mode) or with a higher current
(boost mode).
To change the drive mode, highlight 'CRT drive mode' by pushing the
control disk up or down and press ENTER to display the CRT drive
mode menu.
SERVICE MODE
G2 ADJUSTMENT
GAMMA CORRECTIONS
CRT RUN IN CYCLE
PROJECTOR WARM UP
CRT DRIVE MODE
MORE...
To change the boost mode, push the control disk up or down to select
a display mode and press ENTER to select.
The following modes are available :
- normal
- economic : lower drive current to the CRT's, the lifetime of the CRT's
will enlarge but the light output will reduce.
- tempory boost : higher drive current to the CRT's, the lifetime of the
CRT's will shorten but the light output will be higher. This situation
is tempory, when restarting the projector, the drive mode is
automatically set to normal.
Select with
or
then <ENTER>
<EXIT> to return.
CRT DRIVE MODE
NORMAL
ECONOMIC
TEMPORARY BOOST
PERMANENT BOOST
WARNING : permanent
boost mode reduces the
lifetime
of the CRT's !
Select with
or
then <ENTER>
<EXIT> to return.
- permanent boost : higher drive current to the CRT's, the lifetime of
the CRT's will shorten but the light output will be higher. This setting
will be saved in the EEPROM. When restarting the projector, it will
start up in boost mode.
A warning, permanent BOOST mode in use, will be displayed to inform
the user.
When text is on, this warning will be repeated every time a new
source is selected.
7-8
WARNING
PERMANENT
BOOST MODE
IN USE !
5975688 BARCOVISION 1609s 131097
Messages, warnings and failures
8
INPUT 01
Fh= 15.6 kHz
Fv= 050 Hz
SOURCE 01
enter
password
xxxx
text on
MESSAGES, WARNINGS AND FAILURES
When selecting a new source,
information about this source will
be displayed on the screen. Source
number, horizontal and vertical frequencies of the displayed source.
Announcement of the selected
source.
Message to enter your password.
Password contains 4 digits.
PROJECTOR
ADDRESS :
003
WARNING :
input not
available
WARNING :
source not
available
WARNING :
invalid
key entry
invalid
code entry
WARNING :
end of adjust range
Message when the entered password is wrong.
End of adjustment range.
WARNING :
input no
longer
available
Message will be displayed when
the input source is no longer available. The following message then
appears: 'check input signal or
select new source'.
WARNING :
input selector not
available
It warns you to check the power
connection or the power status of
the RCVDS.
Next message will appear
immediatly on the screen : 'go to
stand-by'.
WARNING :
invalid
frequency
input
The entered frequency or applied
frequency of the source is out of
the projector's range.
Indication of the projector address
when activating the 'ADDRESS'
button on the RCU with a pencil or
other small object.
table is
deleted
Message to inform that selected
table is deleted. This message will
be followed by 'confirm message',
on which the user has to answer.
When using the projector with the
RCVDS, this warning will be displayed when selecting an input
slot of an RCVDS where the input
board is missing.
FAILURE
These messages will be displayed
on the screen when pushing the
TEXT key.
Text ON : the 'bar scale indication'
will be enabled during the change
of an analog control in the 'operational mode' + all warnings and
failures will be displayed.
text off
WARNING :
Text OFF : the 'bar scale indication'
will be disabled during the change
of an analog control in the 'operational mode' + all warnings and
failures will not be displayed.
The input is a valid input but the
source is not connected to the
input terminals or the input source
is switched off.
I2C error
addr. : 7FH
FAILURE
short
circuit on
I2C bus
Hardware failure. Call a qualified
service technician for repair.
Hardware failure. Call a qualified
service technician for repair.
When a wrong key is pressed on
the RCU.
5975688 BARCOVISION 1609s 131097
8-1
Messages, warnings and failures
8-2
FAILURE
RCVDS communication
error
Serial communication error between the RCVDS and the projector.
FAILURE
IRIS communication
error
Communication error between IRIS
800 and the projector. Call a qualified service technician.
WAIT
starting
up
IRIS
Message during the start up of the
IRIS. Message will disappear when
the IRIS is ready to accept commands.
FAN FAILED
Projector
will
switch off
Message when one of the fans are
not working anymore. Projector
switches to stand-by
5975688 BARCOVISION 1609s 131097
Options
9
OPTIONS
IR Receiver 800
RCVDS 05 Source Selector
This infrared receiver unit makes it possible to control the
BARCOVISION 1609s from another room.
There is a communication line with cable between the IR receiver and
the projector or the RCVDS05. The control information from the RCU
can now be sent to this IR receiver.
The IR receiver 800 displays the selected source on a 7-segment
display.
Order number : R9827515
Hardwired RCU.
The control signals from the RCU can be sent to the projector via a
wired connection.
shield
conductor
An optional RCVDS05 makes it possible to connect up to 20 sources
to the projector. When RCVDS's are linked via the expansion module,
even 90 inputs can be connected to the projector.
The selected source number will be displayed on a 2 digit display and
the selected input module will be indicated with a LED on the rear.
Order Numbers RCVDS 05: 110V:
9827888
9827889
220V:
9827880
9827881
Preparing your remote cable :
Use a shielded cable with a maximum length of 100 m and two minijack 3.5 mm connectors (order number : R3131991).
VS05 Switcher
- Peel back the vinyl covering of the cable on both sides and twist the
wire core.
- Solder a jack plug as shown in drawing above to each end of the
cable.
shield = ground
conductor = data information
When the cable is ready, plug one side in the remote control and the
other side in the connector on the rear of the projector labelled
‘remote’.
Projector Control software
The software is user-friendly and makes full use of : mouse control,
pull down menus and dialog boxes.
Two main applications are available with this software : remote
control and transfering and receiving data of projector settings.
The VS05 is a versatile Video and HDTV source selector for all
BARCO's digitally controlled large screen projectors. It offers the
possibility to connect and switch up to 5 different Video sources, 3
different S-Video sources and 1 RGB Analog source to a BARCO
projector. In addition, the audio signal proper to the source, can be
switched to an audio amplifier.
Order Numbers:
110V:
9827890
220V:
9827899
Remote Control Simulation. Advantage : address range 0 to 255.
Adjustment Data : where can it be located when a IBM PC (or
compatible) or MAC or Workstation is connected :
- hard memory device with files of settings.
- the contents of the local memory of the computer.
- the contents of the projector.
5975688 BARCOVISION 1609s 131097
9-1
Options
MAGIK Interface
Ceiling Mount kit CM100
This heavy duty Ceiling Mount Kit enables the projector to be installed
in any ceiling mount application. A heavy duty pulley system facilitates
installation and maintenance.
order number : R9827341
Orbiting Kit
Static pictures are very often shown on large screen projectors,
especially in process control and presentation applications. Due to
the fact that the same picture information is shown for a long period
in the same place, picture tubes can be damaged by 'local burn-in'.
To reduce this problem, a special Orbiting circuit is available which
moves the picture very slowly around a predefined screen area. The
cycle time is very long to make the movement of the projected image
imperceptible.
The use of the orbiting kit is described in appendix A.
Order number : R9827780
Line Doubler Kit
Multifuctional Analog Graphics Interface Kit.
BARCO's MAGIK interface allows the user to connect a presentation
device such as a projector or a professional monitor to any computer
with analog video signal with or without maintaining the connection
with its own display. The MAGIK interface buffers and amplifies any
RGB analog signal with TTL or analog sync without signal loss or
image degradation.
The MAGIK can be delivered together with connection cables for PC,
MAC, SUN or workstation in a nice handbag case.
BARCO's line doubler kit consists of a video decoder with a threeline adaptive Comb filter, an enhancement circuit and the line doubler
itself.
- The three-line adaptive Comb filter improves color transitions and
teduces noise in the video signal.
- The enhancement circuit integrated in the decoder provides sharper
images with clearer outlines.
- The line doubler circuit reduces visible line structure by doubling the
number of lines of the video image.
Order numbers MAGIK with cables and case :
R9828120 (230V)
R9828129 (120V)
Order number MAGIK only :
R9828121 (230V)
R9828128 (120V)
These three circuits work in unison to produce a smoother yet
sharper image which is significantly more appealing when watching
video images.
Order number : R9828161
Adapter and communication cables
BARCO provides several cables to connect peripheral equipment to
the BARCOVISION 1609s.
a. D9-D9 communication cable
- To connect an IBM PC (or compatible) to the projector.
- To connect a RCVDS 800 or RCVDS05 to the projector.
- To connect a IR receiver to the RCVDS800 or RCVDS05 or to the
projector.
- To be used as extension cable for all other adapter cables.
Available length :5 m (16ft), order number R982770; 15 m(50ft), order
number R9827560; and 30 m (100ft), order number R9827570
b. Din Mini8-D9 adapter cable.
- To connect a Macintosh computer to the projector.
Available length : 1 m (3,2 ft), order number R9827640.
c. D25-D9 adapter cable
- To connect a workstation to the projector.
Available length : 1 m (3,2 ft), order number R9827630
d. 5 BNC to 5 BNC cable
- To connect an analog source to the BNC input of the projector
Available lenght : 60 cm, order number R9828260
150 cm, order number R9828261
5 m, order number R9828262
15 m, order number R9828263
9-2
5975688 BARCOVISION 1609s 131097
Orbiting
A
ORBITING
Orbiting (option)
Static pictures are very often shown on large screen projectors,
espectially in process control and presentation applications. Due to
the fact that the same picture information is shown for a long period
on the same place, picture tubes can be damaged by 'local burn-in'.
Adjustment procedure :
The orbiting path is automatically added to the Random access
adjustment mode menu when installed.
Press ADJUST to enter the adjustment mode and select Random.
The Random Access Adjustment Mode menu will be displayed.
Highlight ORBITING by pushing the joy stick forward or backward
and press ENTER.
To avoid this problem, BARCO has designed special Orbiting circuitry
which moves the picture very slow around a predefined screen area.
The orbiting circuitry has been designed using a very long cycle time
to make the movement of the projected image imperceptible.
RANDOM ACCESS
ADJUSTMENT MODE
PICTURE TUNING
GEOMETRY
CONVERGENCE
FOCUSING
COLOR SELECT
ORBITING
CONTR. MODULATION
SOFT EDGE
Select with
or
then <ENTER>
<EXIT> to return.
Orbiting Mode Toggle Switches
The orbiting module is provided with a three pin connector for
connection with the BARCO's BCl link option module, used in multiple
projector installations. For Orbiting, one projector operates as master
wheras the others operate as slave.
Master/Slave Toggle
Highlight 'CHANGE TO SLAVE' with the joy stick and press ENTER
to set the projector as Slave.
Highlight 'CHANGE TO MASTER' with the joy stick and press ENTER
to set the projector as Master.
MASTER ORBITING
CHANGE TO SLAVE
MODE : ON
SPEED : FAST
ADJUST DEVIATION
SELECT WITH
OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH
OR
HORIZONTAL WITH
OR
MASTER ORBITING
<EXIT> to return. CHANGE TO MASTER
MODE : ON
SPEED : FAST
ADJUST DEVIATION
SELECT WITH
OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH
OR
HORIZONTAL WITH
OR
<EXIT> to return.
Orbiting ON/OFF toggle (only in Master Orbiting)
Highlight 'MODE : ON' with the joy stick and press ENTER to set the
ORBITING OFF.
Highlight 'MODE : OFF' with the joy stick and press ENTER to set the
ORBITING ON.
ENTER toggles between mode on and off.
EXIT returns to the Path selection menu.
MASTER ORBITING
CHANGE TO MASTER
MODE : ON
SPEED : FAST
ADJUST DEVIATION
SELECT WITH
OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH
OR
HORIZONTAL WITH
OR
<EXIT> to return.
5975628 BARCOGRAPHICS 1209s 010797
A-1
Orbiting
Orbiting Speed Toggle (only in MASTER Orbiting)
Highlight 'SPEED : SLOW' with the control stick and press ENTER to
set the ORBITING SPEED to Fast.
Highlight 'SPEED : FAST' with the control stick and press ENTER to
set the ORBITING SPEED to Slow
ENTER continues to Set up Orbiting
EXIT returns to path selection menu
ADJUST returns to operational mode.
MASTER ORBITING
CHANGE TO MASTER
MODE : ON
SPEED : FAST
ADJUST DEVIATION
SELECT WITH
OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH
OR
HORIZONTAL WITH
OR
<EXIT> to return.
Orbiting Alignment
Preparation :
Before proceeding to the alignment of the Orbiting default settings,
be sure that the Horizontal Phase and the Raster shift are correctly
aligned with the Orbiting mode set to OFF.
This alignment must be performed in case of a multiple projector
installation with Master and Slave projectors in order to ensure a
correct operation of the Orbiting for all projectors.
Adjustment procedure Stand-Alone projector :
Highlight 'ADJUST DEVIATION' with the control stick and press
ENTER.
SLAVE ORBITING
CHANGE TO MASTER
ADJUST DEVIATION
SELECT WITH
OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH
OR
HORIZONTAL WITH
OR
<EXIT> to return.
When adjusting the horizontal and the vertical deviation, the picture
moves in the corresponding direction, allowing the set up of the
deviation without orbiting operation.
Push the control stick to the right or backward to toggle between Hor.
and Vert. deviation andjustment.
Horizontal
orbitampl.
60
Adjust horizontal deviation by pushing
the control stick to the left or to the right
Vertical
orbitampl.
Adjust vertical deviation by pushing
the control stick forw ard or backward
A-2
60
5975268 BARCOGRAPHICS 1209s 010797
Orbiting
Adjustment procedure multiple projector installations :
Inportant : to allow corrections in the deviation alignments of the slave
projectors, never adjust the deviations of the master projector to its
maximum.
Default setting of the Master projectorn see 'Stand-Alone projector'.
Highlight 'ADJUST DEVIATION' by pushing the control stick forward
or backward and press ENTER.
When adjusting the horizontal and the vertical deviation, the picture
moves in corresponding direction, allowing the set up of the deviation
without orbiting operation.
SLAVE ORBITING
CHANGE TO MASTER
ADJUST DEVIATION
SELECT WITH
OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH
OR
HORIZONTAL WITH
OR
<EXIT> to return.
Push the control stick to the right or backward to toggle between Hor.
and Vert. deviation adjustment.
Horizontal
orbitampl.
Adjust horizontal deviation by pushing
the control stick to the left or to the right
Adjust vertical deviation by pushing
the control stick forward or backward
60
Vertical
orbitampl.
60
5975628 BARCOGRAPHICS 1209s 010797
A-3
Orbiting
A-4
5975268 BARCOGRAPHICS 1209s 010797
Adjustment Blocks and Source Numbers 90-99
B
ADJUSTMENT BLOCKS AND SOURCE
NUMBERS 90 - 99
Adjustment Blocks (memory blocks)
As the projector is digitally controlled, all geometry and convergence adjustments are stored in the projector’s memory as numeric values.
These numeric values are used to control digital potentiometers which in turn, control the projector. Each source connected to the
projector has a unique set of adjustment data which is automatically downloaded into the projector’s digital potentiometers once the
source has been selected. This set of adjustment data is referred to as an “adjustment block”.
An adjustment table is automatically created for a source when the source is first connected to the projector and the Adjustment mode
is entered. If other sources have already been connected to the projector and geometry and convergence adjustments have been
performed on these sources, the projector will use Linear Digital Interpolation to create a new block for the new source. This block
will provide an initial set of adjustments for the new source that have been calculated by the projector from “previous experience”.
The projector’s memory has the capacity to store 32 adjustment blocks. The adjustment block consists of two parts, the block header
and the data representing the values for all adjustments (eg. Convergence and Geometry) in the projector for the source the block
corresponds to. The block header contains the basic characteristics of the source and the projector configuration used to display
the source.
Block Header
example of block header
Block Number
01
Source Number
01
Horizontal Frequency
15.6 kHz
Vertical Frequency
50 Hz
Input Type
video
Scan Switch Configuration
Front/Ceiling
The data representing the various adjustments for the source follows the block header.
Source numbers 90 - 99
Source numbers 90 - 99 do not correspond to physical inputs
to the projector or RCVDS. They are used to assign an
additional adjustment block to a source. This additional adjustment block may contain different geometry and convergence
settings, sync fast/slow positions and enhanced blue on/off
settings. The relationship between source numbers 0 - 9 and
90 - 99 (projector with RCVDS) or 1 - 5 and 91 - 95 (standalone projector) is shown in the diagram below.
source input 0
source input 1
Block header A
source number 90
Block header A, different analog settings
source number 1
Block header B
source number 91
Block header B, different analog settings
source number 2
Block header C
source number 92
Block header C, different analog settings
○ ○ ○
source input 2
source number 0
source input 9
5975688 BARCOVISION 1609s 131097
source number 9
Block header J
source number 99
Block header J, different analog settings
B-1
Adjustment Blocks and Source Numbers 90-99
The alternate adjustment block for sources 0 - 9 (projector with
RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting the
corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5
(stand-alone projector). Once this source number is selected, the
alternate block of adjustment data is in use and may be modified via
the adjust mode of the projector. The alternate adjustment block is
automatically stored.
Follow the steps below to create a second adjustment block for a
source between 0 and 9.
1. Select the source between 0 and 9 that the second adjustment
block is to be created for.
2. Select the corresponding source number between 90 and 99. The
adjustment block for the source number between 0 and 9 is copied
to the corresponding source number between 90 and 99.
3. Enter the adjust mode and make any desired changes (geometry,
convergence, sync fast/slow, enhanced blue on/off) to the second
adjustment block.
4. Exit the adjust mode.
Note : the above also applies to source number 1 - 5 and 91 - 95 of
a stand alone projector (no RCVDS)
B-2
5975688 BARCOVISION 1609s 131097
Insert Card
INSERT CARD
5&8
, 1 3 8 7 6 2 8 5 & ( 6
35 2 -( & 72 5
,1 3 8 7 6 2 8 5 & ( 6
5975628 BARCOGRAPHICS 1209s 010797
5 & 9' 6
5&8
,1 3 8 7 6 2 8 5 & ( 6
3 5 2 -(& 72 5
3
3
, 1 3 8 7 6 2 8 5 & ( 6
5 & 9' 6
i-1