Changzhou Gardensun Furnace HLS01-CGT Owner`s manual

Batch #
PATIO HEATER
OWNER’S MANUAL
HLS01-CGT
AZ Patio Heater Toll Free Number
888-775-1330
IMPORTANT
Read this manual carefully before
assembling, using or servicing this
FOR MODELS:
HLS01-CGT
R
R
heater. Keep this manual for future
reference.
Contents
DANGER
General Safety Information.......................................
1
Assembly Instructions
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
Components & Hardware........................................ 3&4
Additional Requirements........................................
4
WARNING
Installation Process
Step1 - Attach Wheel Assembly to Base.................
4
WARNING indicates an imminently hazardous situation
Step 2 – Attach Bucket to Base..............................
4
which, if not avoided, could result in death or serious injury.
Step 3–Attach Cylinder Housing to Base.............. . 5
Step4–Attach Post to Cylinder Housing...............
5
Step 5 – Tabletop Installation.................................
5
Step 6 – Attach Reflector Studs to Screen Cover...
5
CAUTION indicates an imminently hazardous situation
Step 7 – Attach Head Assembly to Post.................. 6
which, if not avoided, may result in minor or moderate
Step 8 – Install Reflector.........................................
personal injury, or property damage.
6
CAUTION
Step 9 – Attach Reflector Assembly to Studs.......... 7
Step10–Connect Hose & Regulator to Cylinder....
7
Leak Check.............................................................
9
Operation................................................................
9
Operation Checklist
10
Troubleshooting...................................................... 11
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapor and liquids in the vicinity of
this or any other appliance.
Maintenance........................................................... 11
Storage.................................................................... 12
Service.................................................................... 12
WARNING: For Outdoor Use Only
Warranty ................................................................ 12
General Safety Information
WARNING
This manual contains important information about the
assembly, operation and maintenance of this patio heater.
General safety information is presented in these first few
pages and is also located throughout the manual.
Keep this manual for future reference and to educate
new users of this product. This manual should be read in
Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage. Read
the instructions
thoroughly before installing or servicing this
equipment.
conjunction with the labeling on the product.
Safety precautions are essential when any mechanical
or
propane
fueled
equipment
is
involved.
DANGER
These
precautions are necessary when using, storing, and
Failure to comply with the precautions and instructions
servicing. Using this equipment with the respect and
provided with this heater can result in death, serious bodily
caution demanded will reduce the possibilities of personal
injury and property loss or damage from hazards of fire,
injury or property damage.
explosion, burn, asphyxiation, and/or carbon monoxide
The following symbols shown below are used extensively
poisoning.
throughout this manual. Always heed these precautions,
Only persons who can understand and follow the
as they are essential when using any mechanical or
instructions should use or service this heater.
fueled equipment.
1
DANGER
DANGER
• EXPLOSION - FIRE HAZARD
• Keep solid combustibles, such as building materials,
paper or cardboard, a safe distance away from the heater
as recommended by the instructions.
• Provide adequate clearances around air openings into
the combustion chamber.
• Never use the heater in spaces which do or may contain
volatile or airborne combustibles, or products such as
gasoline, solvents, paint thinner, dust particles or unknown
chemicals.
• CARBON MONOXIDE HAZARD
• This heater is a combustion appliance. All combustion
appliances produce carbon monoxide (CO) during the
combustion process. This product is designed to produce
extremely minute, non-hazardous amounts of CO if used
and maintained in accordance with all warnings and
instructions. Do not block air flow into or out of the heater.
• Carbon Monoxide (CO) poisoning produces flu-like
symptoms, watery eyes, headaches, dizziness, fatigue and
• During operation, this product can be a source of
possibly death. You can't see it and you can't smell it. It's
ignition. Keep heater area clear and free from combustible
an invisible killer. If these symptoms are present during
materials, gasoline, paint thinner, cleaning solvents and
operation of this product get fresh air immediately!
other flammable vapors and liquids. Do not use heater in
• For outdoor use only .
areas with high dust content. Minimum heater clearances
• Never use inside house, or other unventilated or
from combustible materials: three (3) feet from the sides &
two (2) feet from the top.
enclosed areas.
• This heater consumes air (oxygen). Do not use in
unventilated or
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish open flame.
3. If odor continues, immediately call your gas
supplier.
enclosed areas to avoid endangering
your life.
CAUTION
• SERVICE SAFETY
• Keep all connections and fittings clean. Make sure
propane cylinder valve outlet is clean.
• Inspect hose before use. Replace if there is evidence of
WARNING
abrasion or wear.
• During set up, check all connections and fittings for leaks
We cannot foresee every use which may be made of our
using soapy water. Never use a flame.
heaters.
• Use as a heating appliance only. Never alter in any way or
Check with your local fire safety authority if you have
use with any device.
questions about heater use.
• Check entire hose at least annually.
Other standards govern the use of fuel gases and heat
producing products for specific uses. Your local authorities
can advise you about these.
If no local codes exist, follow National Fuel Gas Code,
• BURN HAZARD
ANSI Z223.1. In Canada, installation must conform to local
• Never leave heater unattended when hot or in use.
codes. If no local codes exist, follow the current National
• Keep out of reach of children.
standards of CANADA CAN/CGA-B 149.2.
2
WARNING
WARNING
• This product is fueled by propane gas. Propane gas is
invisible, odorless, and flammable. An odorant is normally
added to help detect leaks and can be described as a
“rotten egg” smell. The odorant can fade over time so
leaking gas is not always detectable by smell alone.
Assembly Instructions
Components
Remove all components from package.
Reflector Panel(3)
Reflector Plate
• Propane gas is heavier than air and leaking propane will
sink to the lowest level possible. It can ignite by ignition
Reflector Assembly
sources including matches, lighters, sparks or open flames
of any kind many feet away from the original leak. Use only
propane gas set up for vapor withdrawal.
• Propane gas should be stored or used in compliance with
Reflector Stud(3)
Heater Burner
Screen
local ordinances and codes or with ANSI/NFPA 58. Turn off
propane when not in use.
Head Assembly
Cylinder Housing
DANGER
• EXPLOSION - FIRE HAZARD
• Never store propane near high heat, open flames, pilot
lights, direct sunlight, other ignition sources or where
temperatures exceed 120 degrees F (49°C).
• Propane vapors are heavier than air and canaccumulate
Post
in low places. If you smell gas, leave the area immediately.
• Never install or remove propane cylinder while heater is
lighted, near flame, pilot lights, other ignition sources or
while heater is hot to touch.
• This heater is red hot during use and can ignite
flammables too close to the burner. Keep flammables at
least 3 feet from sides & 2 feet from top. Keep gasoline and
other flammable liquids and vapors well away from heater.
Gas Hose Less
Regulator
• The propane cylinder must always be stored outdoors in a
well ventilated space. Never store propane cylinder in an
enclosed area (house, garage, etc.). If heater is to be
Regulator
Base
stored indoors, disconnect the propane cylinder for outdoor
storage.
Wheel
3
WARNING
California Proposition 65
Combustion by products produced when using
this product contain chemicals known to the state
of California to cause cancer, birth defects, and
other reproductive harm.
Used in
Hardware
Picture
Qty
Description
Step(s)
6
Large Bolt
2/3
4
Large Flat
Washer
3
8
Small Screws
3
8
Small Nuts
3
10
Small Bolt
2/4
6
Large Flat Washer
9
Cap Nut
Installation process
(For models without
.
.
Assembly time: 0.5 hour
Wheels , skip to Step 2)
Step 1 – Attach Wheel Assembly to Base
Line up holes in Wheel Bracket with corresponding
holes in base, insert 2 large bolts through holes and
finger tighten 2 Large Nuts.
.
Be sure that the Wheel Assembly
is parallel to the
base, and fully tighten bolts
Wheel Assembly
9
8
2 Req’d Large Bolts
6
Large Nuts
2
9
Small Screw
8
3
Wing Nut
9
10
Flange Nuts
3
Reflector Stud
6
4
Large Screws
2
1
Wrench
2 Req’d Large Nuts
2/4
1/3/4/
7/8
(For models without
Bucket , skip to Step 3)
Step 2 – Attach Bucket to Base
Additional Requirements
The following items are not included, but are necessary for
..
.
the proper assembly of your heater. Do NOT attempt to
assemble without proper tools.
Philips screwdriver w/ medium blade.
Adjustable opening wrench.
Leak Detection Solution(Instructions on how to make
solution are included in step )
Note: You must follow all steps to properly assemble
heater.
4
..
.
Slide 4 Large screws through holes of Base.
Slide 4 Large nuts through holes under bucket .
and tighten screws with phillips screw driver.
4 Req’d Large Screws
Fill bucket with sand
4 Req’d Large Nuts
Step 5 – Tabletop Installation
Put the Plastic nut & Fastening piece through the post
in order.Put the Tabletop through the post as show.
.
Fill Sand
Optional ground fixtures for surface mounting. Not for use in
conjunction with wheels. (Not available with all models)
Mount optional ground fixtures with 6 pcs small bolts
and flange nuts into holes on base housing.
Step 3 – Attach Cylinder Housing to Base
Attach l-shaped brackets to base housing loosely with 4pcs
M8 X M10 large bolts and large flat washers.
Attach cylinder to housing to base with 8 small phillips screws
and 8 small nuts. Tighten all hardware from this step.
Put the Plastic connecting through the post as show.
Step 4 – Attach Post to Cylinder Housing top
Open the door, put post through the hole on the top of
Cylinder Housing.
Through the Fastening piece to the hole on the Tabletop.Hold
the t abletop using a hand and screw the Fastening piece to the
Plastic connecting counter-clockwise using the other one. Fasten the
Fastening piece.Screw the Plastic nut to the Plastic connecting
counter-clockwise. Fasten the Plastic nut.
Adjust the height of the Tabletop. Loose the Plastic nut and adjust
the Tabletop height of you want. Fasten the Plastic nut.
Attach post to Cylinder Housing using 4pcs small bolts
into Flange nuts from inside tank housing.
..
Step 6 – Attach Reflector Studs to Screen Cover
Insert 3 Reflector Studs
Tighten studs securely.
3 Req’d Reflector Studs
(For models without tabletop, skip to Step 6)
5
.
Step 7 – Attach Head Assembly to Post
9 Req’d Small Screws
Unscrew 4 small bolts from head assembly.
4 Req’d Small Bolts
from Head Assembly
..
.
.
.
Load Head Assembly by inserting hose into post.
Insert Head Assembly into post.
Control knob should be above decal on post.
.
9 Req’d Cap Nuts
Attach Cap Nut and loosely tighten.
Attach Head Assembly to post, and loosely install four
small bolts.
Tighten bolts securely.
(For models with Entire Reflector , skip to Step 9)
Step 8 – Install Reflector
WARNING
.
Place Reflector center plate into middle of reflector panels
and follow same procedure above.
Remove protective cover before assemble.
Note: Leave all screws and nuts loose until entire shield is
put together to ensure proper alignment. Tighten after
sections are aligned.
..
6
Slide two reflector panels together.
Insert one small screw.
.
.
Repeat procedure to complete the assembly of all four
sections.
Fully tighten all of the screws in the rolled edge.
..
Step 9 – Attach Reflector Assembly to Studs
Slide 3 Large Flat Washers over threaded end of
Studs.
6 Req’d Large Flat Washers
..
The minimum permissible gas supply pressure of
10 W.C. is required for purpose of input adjustment.
Support Heater.
3 Req’d Wing Nuts
Position Reflector Assembly on 3 studs.
Install large flat washers on studs & securely tighten
wing nuts but do not over-tighten!
.
.
.
.
.
.
The minimum hourly of 17000 Btu is required input
rating for a heater for automatic operation at ratings
less than full input rating.
The pressure regulator and hose assembly supplied
with the appliance must be used.
The installation must conform with local codes, or in
the absence of local codes, with National Fuel Gas
Code, ANSI Z223.1.
A dented, rusted or damaged propane cylinder may
be hazardous and should be checked by your cylinder
supplier. Never use a propane cylinder with a
damaged valve connection.
The propane cylinder must be constructed and
marked in accordance with the specifications for LP
gas
cylinders
of
the
U.S.
Department
of
Transportation (DOT).
Never connect an unregulated propane cylinder to the
heater.
Screw regulator onto gas hose. Do not cross-thread.
Step 10 – Connect Hose & Regulator to Cylinder
.
.
Specifications
You
must
propane
Tighten securely with wrenches.
provide
gas
Attach regulator to cylinder.
and
Complete attachment.
propane cylinder. Use a
standard 20 lb. propane
cylinderonly.( 5 gal.)
Use this heater only
with a propane vapor
withdrawal
supply
system. See Chapter 5
of
the
Standard
Install cylinder.
for
Storage and Handling
of Liquefied Petroleum
Standard 20 lb. tank
Gas, ANSI/NFPA 58.
Your local library or
fire department should have this book.
7
Leak Check
Operation
WARNING
DANGER
• Perform all leak tests outdoors.
• Extinguish all open flames.
• CARBON MONOXIDE HAZARD
• NEVER leak test when smoking.
• Do not use the heater until all connections have been leak
• For outdoor use only. Never use inside house, or other
tested and do not leak.
unventilated or enclosed areas. This heater consumes air
(oxygen). Do not use in unventilated or enclosed areas to
avoid endangering your life.
DANGER
• EXPLOSION - FIRE HAZARD
.
.
.
..
..
.
• Never store propane near high heat, open flames, pilot
Hose / Regulator
Regulator / Cylinder
Connection
Connection
lights, direct sunlight, other ignition sources or where
temperatures exceed 120 degrees F (49°C).
Make 2-3 oz. of leak check solution (one part liquid
dishwashing detergent and three parts water).
• Propane vapors are heavier than air and can accumulate
in low places. If you smell gas, leave the area immediately.
Apply several drops of solution where hose attaches
to regulator.
• Never install or remove propane cylinder while heater is
lighted, near flame, pilot lights, other ignition sources or
Apply several drops of solution where regulator
connects to Cylinder.
while heater is hot to touch.
• This heater is red hot during use and can ignite
Make sure all Patio Heater & Light valves are OFF.
Turn Cylinder Valve ON.
flammables too close to the burner. Keep flammables at
least 3 feet from sides & 2 feet from top. Keep gasoline and
If bubbles appear at any connection, there is a leak.
other flammable liquids and vapors well away from heater.
Turn Cylinder Valve OFF.
• The propane cylinder must always be stored outdoors in a
If leak is at Hose/Regulator connection: tighten
connection and perform another leak test.
well ventilated space. Never store propane cylinder in an
enclosed area (house, garage, etc.). If heater is to be
If leak is at Regulator/Cylinder Valve connection:
disconnect, reconnect, and perform another leak
stored indoors, disconnect the propane cylinder for outdoor
storage.
check. If you continue to see bubbles after several
attempts, cylinder valve is defective and should be
returned to cylinder’s place of purchase.
.
.
If
NO
bubbles
appear
at
any connection,
Caution: Do not attempt to operate until you have read
the
connections are secure.
Turn Cylinder Valve OFF.
NOTE: Whenever gas connections are loosened or
removed, you must perform a complete leak test.
8
Complete installation.
& understand all General Safety Information in this
manual and all assembly is complete & leak checks
have been performed.
.
.
..
..
.
.
.
Before Turning Gas Supply ON:
Your heater was designed and approved for outdoor
4
visible through Viewing Hole.
5
Release Control Knob after 30-60 seconds. Pilot
Light will remain lit. If not, return to step 1.
use only. Do NOT use it inside a building, garage, or
any other enclosed area.
Push and release the igniter button until pilot flame is
6
Turn Control Knob to ON. Main Burner will light
Make sure surrounding areas are free of combustible
immediately. Flame is visible through Viewing Hole. If
materials, gasoline, and other flammable vapors or
not, return to step 1.
liquids.
Ensure that there is no obstruction to air ventilation.
Be sure all gas connections are tight and there are no
leaks.
Be sure the cylinder cover is clear of debris.
Be sure any component removed during assembly or
servicing is replaced and fastened prior to starting.
Before Lighting:
Heater should be thoroughly inspected before eachuse, and by a qualified service person at least
annually.
If relighting a hot heater, always wait at least 5
minutes.
Inspect the hose assembly for evidence of excessive
abrasion, cuts, or wear. Suspected areas should be
leak tested. If the hose leaks, it must be replaced prior
to operation. Only use the replacement hose
assembly specified by manufacturer.
.
If for some reason your igniter fails to deliver a spark,
your heater can be started by inserting a lit match
through the pilot view hole while pushing the control
knob in while in the PILOT position.
Lighting:
Note: This heater is equipped with a Pilot Light that allows
for safer startups and shutdowns. Pilot must be lit before
Main Burner can be started.
1
Turn Cylinder Valve ON.
2
Open Viewing Hole by sliding cover to either side.
3
Push Control Knob IN and rotate to Pilot position.
Note: For initial start or after any cylinder change, hold
Control Knob IN for 2 minutes to purge air from gas lines
Note: If pilot fails to remain lit, all valves should be closed
and waiiting period of at least 5 minutes should pass before
attempting to light.
before proceeding.
9
If
you
experience
any
ignition
problem please
consult “Troubleshooting” on page 11.
Caution: Avoid inhaling fumes
emitted from the
heater’s first use. Smoke and odor from the burning of
oils used in manufacturing will appear. Both smoke
and odor will dissipate after approximately 30 minutes.
The heater should NOT produce thick black smoke.
Note: The burner may be noisy when initially turned on. To
.
.
.
Shut Down:
Turn Control Knob clockwise to Pilot. (Normally,
burner will make a slight popping sound when
extinguished.) Burner will extinguish but Pilot will
remain ON.
To extinguish Pilot, depress Control Knob and
continue to turn it clockwise to OFF.
Turn Cylinder Valve clockwise to OFF and disconnect
Regulator when heater is not in use.
eliminate excessive noise from the burner, turn the Control
Note: After use, some discoloration of the emitter screen is
Knob to the Pilot position. Then, turn the knob to the level
normal.
of heat desired.
Operation Checklist
WARNING
FOR YOUR SAFETY
Be careful when attempting to manually ignite this heater.
Holding in the control knob for more than 10 seconds
before igniting the gas will cause a ball of flame upon
ignition.
When heater is ON:
Emitter screen will become bright red due to intense heat.
The color is more visible at night.
Burner will display tongues of blue and yellow flame. These
flames should not be yellow or produce thick black smoke,
indicating an obstruction of airflow through the burners. The
flame should be blue with straight yellow tops.
If excessive yellow flame is detected, turn off heater and
consult “Troubleshooting” on page 11.
Re-lighting:
Note: For your safety, Control Knob cannot be turned OFF
..
.
without first depressing Control Knob in PILOT position and
then rotating it to OFF.
Turn Control Knob to OFF.
Wait at least 5 minutes, to let gas dissipate, before
attempting to relight Pilot.
Repeat the “Lighting” steps on prior page.
..
..
..
..
...
.
.
.
...
Before Operating:
I am familiar with entire owner’s manual and
understand all precautions noted .
All components are properly assembled, intact and
operable.
No alterations have been made.
All gas connections are secure and do not leak.
Wind velocity is below 10 mph.
Unit will operate at reduced efficiency below 40°F.
Heater is outdoors (outside any enclosure).
There is adequate fresh air ventilation.
Heater is away from gasoline or other flammable
liquids or vapors.
Heater is away from windows, air intake openings,
sprinklers and other water sources.
Heater is at least 24" on top and at least 36" on sides
away from combustible materials.
Heater is on a hard and level surface.
There are no signs of spider or insect nests.
All burner passages are clear.
All air circulation passages are clear.
Children, pets, clothing, flammable materials and
items that can be damaged from radiant heat are
away from the heater.
Children and adults in the area have been alerted to
the high temperature hazards: especially burns and
clothing fires.
Children and adults in the area have been warned not
to touch heater near engine during operation and until
unit has cooled.
After Operation:
WARNING
FOR YOUR SAFETY
Heater will be hot after use. Handle with extreme care.
10
For a safe and pleasurable heating experience, perform
this check before each use.
Gas control is in OFF position.
Gas Tank valve is OFF.
Disconnect Gas line.
Heater is upright in a secure location.
Troubleshooting
If the problem is:
And this condition exists:
Then do this
Cylinder valve is closed
Open valve
Blockage in orifice or pilot tube
Clean or replace orifice or pilot tube
Air in gas line
knob in) for not more than 1 - 2 minutes or
Open gas line and bleed it (pressing control
Pilot won’t light
until
you smell gas
Low gas pressure with cylinder valve
Note:
Heater
operates
at
reduced efficiency below 40ºF
Turn cylinder valve OFF and replace
fully open
Use match to light pilot; obtain new igniter
Igniter fails
Dirt built up around pilot
Clean dirt from around pilot
Connection between gas valve and
Tighten connection and perform leak check
pilot assembly is loose
Thermocouple is not operating
Burner won’t light
correctly
Replace thermocouple
Gas pressure is low
Turn cylinder valve OFF and replace
Blockage in orifice
Clear blockage
Control knob is not in ON position
Turn control knob to ON
Gas pressure is low
Turn cylinder valve OFF and replace
Outdoor temperature is less than
Burner flame is low
40ºF
and tank is less than 1/4 full
cylinder
cylinder
Use a full cylinder
Supply hose is bent or kinked
Straighten hose
Control knob fully ON
Check burner and orifices for blockage
Carbon build-up
Dirt or film on reflector and burner screen
Clean reflector and burner screen
Thick black smoke
Blockage in burner
Maintenance
and
replace
(5ºC)
Pilot won’t stay lit
cylinder
Remove blockage and clean burner inside and
outside
.
.
Keep exterior surfaces clean.
WARNING
FOR YOUR SAFETY:
• Do NOT touch or move heater for at least 45 minutes
Use warm soapy water for cleaning. Never use
flammable or corrosive cleaning agents.
While cleaning your unit, be sure to keep the area
around the burner and pilot assembly dry at all
after use.
times.
Do
not
submerge
the
control
valve
• Reflector is hot to the touch.
assembly. If the gas control is submerged in water,
• Allow reflector to cool before touching.
do NOT use it. It must be replaced.
To enjoy years of outstanding performance from your
Air flow must be unobstructed. Keep controls, burner,
heater, make sure you perform the following maintenance
and circulating air passageways clean. Signs of possible
activities on a regular basis:
blockage include:
11
..
..
.
.
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heater glow is excessively uneven.
Heater makes popping noises.
.
.
.
Store heater upright in an area sheltered from direct
contact with inclement weather (such as rain, sleet,
hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces
and to help prevent build up in air passages.
Never leave LP cylinder exposed to direct sunlight or
excessive heat.
Note: Wait until heater is cool before covering.
Spiders and insects can nest in burner or orifices.
This dangerous condition can damage heater and
Service
render it unsafe for use. Clean burner holes by using
a heavy-duty pipe cleaner. Compressed air may help
Repair to gas passages and associated components
clear away smaller particles.
should be done only by a qualified service person.
Carbon deposits may create a fire hazard. Clean
dome and burner screen with warm soapy water if
Caution:
any carbon deposits develop.
attempting service.
Always
allow
heater
to
cool
before
Note: In a salt-air environment (such as near an ocean),
corrosion occurs more quickly than normal. Frequently
check for corroded areas and repair them promptly.
TIP:
Use high-quality automobile wax to help maintain the
appearance of your heater. Apply to exterior surfaces from
the pole down. Do not apply to emitter screen or domes.
Storage
..
.
.
Between uses:
Turn Control Knob OFF.
Disconnect LP source.
Store heater upright in an area sheltered from direct
contact with inclement weather (such as rain, sleet,
hail, snow, dust and debris).
If desired, cover heater to protect exterior surfaces
and to help prevent build up in air passages.
Note: Wait until heater is cool before covering.
..
During periods of extended inactivity or when
transporting:
12
Turn Control Knob OFF.
Disconnect LP source and move to a secure,
well-ventilated location outdoors.
Warranty
1 YEAR LIMITED WARRANTY - CUSTOMERS IN CANADA
IMPORTANT
Only return this product to the store if it was purchased within 90
days. If you have problems af ter 90 days of purchase, please
email our customer service department for any questions or
concerns: www.patioheaterpartsonline.com OR PLEASE
CALL 888-775-1330 DATED PROOF OF PURCHASE
REQUIRED FOR WARRANTY SERVICE.
WARRANTY
This product is inspected, tested and carefully packaged to
minimize the chance of damage during shipment. If a part
(excluding light bulbs and fuses*) within one year from the date of
purchase proves to be defective in material or fabrication under
normal use, the part will be repaired or replaced. The Company's
obligation under the warranty is to replace or repair defective parts
at our discretion. Any expenses or damage resulting from the
installation, removal or transportation of the product will the
responsibility of the owner and are not covered by this warranty.
The owner assumes all other risks arising out from the use or
misuse of the product. The warranty will be void if the product
damage or failure is deemed by the Company to be caused by
accident, alteration, misuse, abuse, incorrect installation or
removal, or connection to an incorrect power source by the owner.
The Company neither assumes, nor authorizes any person or
entity to assume for it any obligation or liability associated with its
products. * Light bulbs and fuses are not covered under this
warranty. If you have any questions regarding the warranty or
service, please call our toll free number: 888-775-1330
Distributed by:
AZ Patio Heaters
8550 N 91st Ave Ste C-25
Peoria, AZ 85345
Manufactured by:
Changzhou Gardensun Furnace Co., Ltd.
No. 1, Boyi Town, Changzhou City,
Jiangsu Province P.R. China