VHF AND UHF TRANSCEIVERS
(VHF Transceiver)
(UHF Transceiver)
ch /
12 8 es
n
8 zo
one
, 5-T patible
e
n
2 -To1200 com
MDC
RF
5W W AF
m
700
ht
t-tig of
s
u
ro
7D
IP6 Waterp
and
r
e
g
a
P
R adio
er
act
har play
c
8
dis
LCD
ce
Voi rder
o
rec
on
r at i
V ib
t
aler
VIBRATION ALERT
700 mW AUDIO OUTPUT
(typ.)
VOICE STORAGE
Vibration alert function
When a pre-programmed 2-tone/5-tone code or call from a
specific user (MDC mode only) is received, the radio vibrates
powerfully enough to be felt through heavy clothing.
8 minute voice recorder
When a pre-programmed 2-tone/5-tone code or a SelCall
(MDC mode only) is received, the voice recorder automatically starts recording the incoming message. You will not
miss an important call even when you are temporarily away
from the radio. You can manually start recording incoming
calls and also your own message. It records up to a maximum of 8 minutes (Or up to 48
calls of 10 sec. recording time).
“
” icon on the display shows you have a new message.
700mW audio output
The IC-F50V series delivers a loud 700mW* audio output
with the built-in BTL amp. The built-in audio compander
provides clear, low noise communications. Improved bass
characteristics also betters the audio quality.
* Typical with internal speaker.
Lone worker function for remote check in
When the radio is not operated for a preset period (1 to
255 min.), the radio sounds a beep and requires you to
push any button. If the radio is not operated for a preset
time (1 to 255 sec.), an emergency signal automatically
transmits and informs your co-worker or dispatcher that
something may have happened to the individual worker.
IP67, dust-tight and
waterproof protection
The IC-F50V series has outstanding
protection against dust and water
that is equivalent to IP67. The ICF50V series can withstand submersion in 1m depth of water for up to 30
minutes and has dust-tight construction that prevents the ingress of dust.
Most popular signalings built-in
VHF AND UHF TRANSCEIVERS
(VHF transceiver)
(UHF transceiver)
Use the built-in CTCSS, DTCS, 2-Tone, 5-Tone and MDC
signaling capabilities to set up your talk group or selective
calling. The IC-F50V series can decode ten 2-Tone codes
or eight 5-Tone codes on a channel. When a matched
tone is received, the following actions are programmable
for each code.
• Bell icon
• Answer back call • Beep sound
• Auto transmit • Radio Stun/Kill/Revive
• Voice recorder • Vibration alert
OPTIONS
Some options may not be available in some countries. Please ask your dealer for details.
BATTERY PACK & CASE
MULTI-CHARGER
BC-157
BP-226
MDC 1200 Compatible
The following selective calling and ANI features are available with the built-in MDC signaling.
• PTT ID
• Radio check • Caller ID • Call alert
• SelCall
• Emergency, emergency mic monitoring
• 500 Aliases • Status/message • Radio stun/revive
BC-121N+AD-100 (6 pcs.)
BP-227
BP-226 : AA (LR6)×5 BATTERY CASE
BP-226 is water-resistant, equivalent to IPX4.
BP-227 : 7.2V/1700mAh Li-Ion BATTERY PACK
Provides 9–10 hours operating time* (approx.).
BC-121N MULTI-CHARGER + AD-100
CHARGER ADAPTER + BC-157 AC ADAPTER
Rapid charges up to 6 battery packs (Six AD-100s
are required) in 2–2.5 hrs.
Operating temp. range: –20°C to +60°C; –4°F to +140°F.
* Tx: Rx: standby=5:5:90.
RAPID CHARGER
RAPID CHARGER
BATTERY CHARGER
Mode dependent scan
In the mode dependent setting, the scanning setting is dependent on the operating channel. When you change the
operating channel, the scanning list automatically changes
to the operating channel setting. It is convenient when you
move to a different operating area and change an operating channel, you don’t have to change the scanning setting.
Enhanced scanning
The Tx channel while scanning can be programmed per
scanning list. The talk back function allows you to transmit
on the channel detected after scanning resumes after a
preset time, prior to the Tx channel setting. The nuisance
delete function temporarily deletes a busy channel from
the scanning list. Backlight at scan stop automatically
turns on the LCD backlight when the scan stops.
Compact body
56(W)×97(H)×36.4(D) mm* compact body with durable,
dependable construction, has been tested to MIL standard
specifications. * 27⁄32(W)×313⁄16(H)×17⁄16(D) in
BC-145L
BC-190
BC-145
BC-119N+AD-100
BC-119N DESKTOP CHARGER
+ AD-100 CHARGER ADAPTER
+ BC-145 AC ADAPTER
Rapidly charges the BP-227 in
2–2.5 hrs.
BC-190 DESKTOP CHARGER
+ BC-145L AC ADAPTER
Rapidly charges the BP-227.
Charge the radio, even when the
radio power is on.
BC-147
BC-152
BC-152 DESKTOP CHARGER
+ BC-147 AC ADAPTER
Regularly charges the BP-227
in 9–10 hours.
HEADSETS & VOX/PTT CASE
HS-94
HS-95
HS-97
VS-1SC
HS-94 : Earhook headset with flexible boom microphone.
HS-95 : Behind-the-head headset with flexible boom microphone.
HS-97 : Throat microphone fits around your neck and picks up speech vibration.
VS-1SC : VOX/PTT CASE. Required when using these headsets with the transceiver.
These headsets and VS-1SC are water-resistant, equivalent to IPX4.
SPEAKER-MICROPHONES
Li-Ion battery pack
The large capacity 1700mAh Lithium-Ion (Li-Ion) battery
pack, BP-227 provides a practical 9–10 hours* of operating
time. With the new BC-190 charger, catch calls even during
the night while charging the battery with the radio power on.
* Typical operation Tx:Rx: Stand-by=5:5:90
HM-138
HM-168
HM-169
HM-170GP
HM-138 : Full sized speaker-microphone. Equivalent to IPX7.
HM-168 : Compact type speaker-microphone. Equivalent to IPX7.
HM-169 : Rugged type speaker-microphone. Equivalent to IP57.
HM-170GP: GPS speaker-microphone for BIIS mode. Equivalent to IP57.
BELT CLIPS &
LEATHER BELT HANGERS
POWER SUPPLY CABLES
Other features
• 128 memory channels with 8 zones
• Inversion type*1 voice scrambler built-in
• Optional VOX headsets available
• Optional GPS speaker-microphone
• Power ON password • 8 DTMF autodial
• 8-character alphanumeric display
• Normal and priority scans
• 2-step power saver and 2-step low battery beep
• BIIS 1200 mode programmable
• Busy, repeater lockout functions
• BTL only version (no vibration alert and no voice recorder)
and BTL/Vibration alert version (no voice recorder) available*2 and more...
*1 Inversion type voice scrambler is not compatible with UT-109/UT-110 voice
scrambler. UT-109/UT-110 cannot be physically installed into the radio.
*2 Not available in some countries. (Not available in the U.S.)
MB-86
MB-96F
MB-86 : Swivel type. Prevents accidental dropping from your belt.
MB-98 : Alligator type. Same as supplied.
MB-96F : Fixed type belt hanger for use with MB-98.
MB-96N: Swivel type belt hanger.
CP-17L
OPC-515L
OPC-656
CP-17L
: CIGARETTE LIGHTER CABLE
For use with BC-119N and BC-152.
OPC-515L: DC POWER CABLE
For BC-119N and BC-152.
OPC-656 : DC POWER CABLE for BC-121N.
ANTENNAS
ANTENNAS
FA-S24V : 136–150MHz (Blue)
FA-S59V : 150–174MHz (Red)
FA-S24V
FA-S59V
FA-S62VS
FA-S63VS
STUBBY ANTENNAS
FA-S62VS: 150–162MHz (Red, 90mm)
FA-S63VS: 160–174MHz (Green, 90mm)
VHF AND UHF TRANSCEIVERS
SPECIFICATIONS
GENERAL
• Frequency range
IC-F50V
IC-F60V
RECEIVER
:
• Sensitivity
: 0.25µV typ. (at 12dB SINAD)
• Squelch sensitivity
: 0.25µV typ. (at threshold)
• Adjacent channel selectivity : 75dB typ. (wide)
65dB typ. (narrow)
• Spurious response
: 70dB
• Intermodulation
: 74dB typ.
• Hum and noise
: 45dB typ. (wide)
40dB typ. (narrow)
• Audio output power
: 0.7W typ. (Internal speaker)
0.5W typ. (External speaker)
136–174MHz
400–470MHz
450–512MHz (U.S.A.)
450–520MHz (General)
• Number of channels
: Max. 128 channels/ 8 zones
• Channel spacing
: 12.5/25kHz , 15/30kHz
• Antenna impedance
: 50Ω (SMA Type)
• Frequency error
: ±2.5ppm
• PLL channel step
: 2.5/3.125kHz
• Power supply requirement : 7.2V DC
• Current drain (approx)
:
Transmit High
1.8A
Receive AF max. 500mA (Internal speaker)
300mA typ. (External speaker)
Stand-by 85mA
• Operating Temp. range : –30˚C to +60˚C; –22˚F to +140˚F
• Dimensions (W × H × D) : 56 × 97 × 36.4 mm ;
(projections not included)
27⁄ 32 × 313⁄16 × 17⁄ 16 in.
• Weight (approx.) VHF
: 280g; 9.9oz (With BP-227)
UHF
284g; 10.0oz (With BP-227)
at 5% distortion with an 8Ω load
• External SP connector
: 9-pin multi connector/8Ω
Applicable U.S. Military Specifications & IP Rating
Icom makes rugged products that have been tested to and passed the following
MIL-STD requirements and Ingress Protection standards.
MIL 810F
Standard
Method
500.4
501.4
502.4-3
503.4
505.4
506.4
507.4
509.4
510.4
514.5
516.5
Low Pressure
High Temperature
Low Temperature
Temperature Shock
Solar Radiation
Rain
Humidity
Salt Fog
Dust
Vibration
Shock
TRANSMITTER
Procedure
I, II
I, II
I, II
I
I
I, III
–
–
I
I
I, IV
Also meets equivalent MIL-STD-810-C, -D and -E.
Ingress Protection Standard
Dust & Water
• Output power
IC-F50V : 5.0W
IC-F60V 4.0W
• Modulation system
: Variable reactance frequency
modulation
• Max. frequency deviation : ±5kHz (wide)
±2.5kHz (narrow)
• Modulation limiting
: 60–100% of Max. deviation
• Audio harmonic distortion : 3% typ. (AF 1kHz, 40% deviation)
• Spurious emissions
: 70dB min.
• Adjacent channel power : 70dB min. (wide)
60dB min. (narrow)
• FM Hum and Noise
: 46dB typ. (wide)
40dB typ. (narrow)
• External MIC impedance : 9-pin multi connector/2.2kΩ
IP67 (Dust-tight and waterproof protection)
Supplied accessories:
• Antenna (Length may differ according to version)
▲ VHF antenna
▲ UHF antenna
Measurements made in accordance with EIA-152C/204D, TIA-603.
All stated specifications are subject to change without notice or obligation.
• Battery pack, BP-227
• Alligator-type belt clip, MB-98
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries.
1-1-32, Kami-minami, Hirano-ku, Osaka 547-0003, Japan Phone: +81 (06) 6793 5302
Fax: +81 (06) 6793 0013
URL: http://www.icom.co.jp/world/index.html
2380 116th Avenue NE,
Bellevue, WA 98004, U.S.A.
Phone : +1 (425) 454-8155
Fax
: +1 (425) 454-1509
E-mail : sales@icomamerica.com
URL : http://www.icomamerica.com
146A Harris Road, East Tamaki,
Auckland, New Zealand
Phone : +64 (09) 274 4062
Fax
: +64 (09) 274 4708
E-mail : inquiries@icom.co.nz
URL : http://www.icom.co.nz
Unit 9, Sea St., Herne Bay,
Kent, CT6 8LD, U.K.
Phone : +44 (01227) 741741
Fax
: +44 (01227) 741742
E-mail : info@icomuk.co.uk
URL : http://www.icomuk.co.uk
6F No. 68, Sec. 1 Cheng-Teh Road,
Taipei, Taiwan, R.O.C.
Phone : +886 (02) 2559 1899
Fax
: +886 (02) 2559 1874
E-mail : sales@asia-icom.com
URL : http://www.asia-icom.com
Glenwood Centre #150-6165 Highway 17,
Delta, B.C., V4K 5B8, Canada
Phone : +1 (604) 952-4266
Fax
: +1 (604) 952-0090
E-mail : info@icomcanada.com
URL : http://www.icomcanada.com
Communication Equipment
Himmelgeister Str. 100,
D-40225 Düsseldorf, Germany
Phone : +49 (0211) 346047
Fax
: +49 (0211) 333639
E-mail : info@icomeurope.com
URL : http://www.icomeurope.com
Zac de la Plaine,
1 Rue Brindejonc des Moulinais, BP 45804,
31505 Toulouse Cedex 5, France
Phone : +33 (5) 61 36 03 03
Fax
: +33 (5) 61 36 03 00
E-mail : icom@icom-france.com
URL : http://www.icom-france.com
10C07, Long Silver Mansion, No.88, Yong Ding
Road, Haidian District, Beijing, 100039, China
Phone : +86 (010) 5889 5391/5392/5393
Fax
: +86 (010) 5889 5395
E-mail : bjicom@bjicom.com
URL : http://www.bjicom.com
Unit 1 / 103 Garden Road,
Clayton, VIC 3168 Australia
Phone : +61 (03) 9549 7500
Fax
: +61 (03) 9549 7505
E-mail : sales@icom.net.au
URL : http://www.icom.net.au
Ctra. Rubi, No. 88 "Edificio Can Castanyer"
Bajos A 08174, Sant Cugat del Valles,
Barcelona, Spain
Phone : +34 (93) 590 26 70
Fax
: +34 (93) 589 04 46
E-mail : icom@icomspain.com
URL : http://www.icomspain.com
81-850 Sopot, ul. 3 Maja 54, Poland
Phone : +48 (58) 550 7135
Fax
: +48 (58) 551 0484
E-mail : icompolska@icompolska.com.pl
URL : http://www.icompolska.com.pl
Count on us!
Your local distributor/dealer:
07WY013B
© 2007–2008 Icom Inc.
Printed in Japan