advertisement
21-1703.fm Page 1 Wednesday, June 2, 1999 4:35 PM
Cat. No. 21-1703
OWNER’S MANUAL
Please read before using this equipment.
TRC-503
40 Channel Mobile CB Radio
with Channel 9/19 Priority Switch
21-1703.fm Page 2 Wednesday, June 2, 1999 4:35 PM
FEATURES
Your RadioShack TRC-503 40 Channel
Mobile CB Radio is a breakthrough in
CB design technology. You can mount it in a vehicle for mobile use, or in your home for use as a base station. Your CB has these advanced features:
Emergency Channel Switch — lets you quickly switch to Channel 9 or
Channel 19 so you can monitor or report emergency situations.
TX and RX Indicators — light to show when the radio is transmitting or receiving.
Full Legal Power — gives you the greatest available range.
Automatic Noise Limiter — reduces impulse-type noises while receiving.
External Speaker Jack — lets you connect your CB to an external speaker.
Phase-Locked Loop (PLL) Frequency
Synthesizer — provides highly accurate and stable tuning.
Two Built-In Ceramic Filters — ensure superior channel selectivity and freedom from adjacent channel interference.
Automatic Modulation Control — prevents the transmitter signal from overmodulating and distorting.
Universal Mounting Bracket — lets you mount your CB securely in your vehicle or on a table or shelf in your home.
Note: To use this CB, you must connect a mobile or base station antenna. Your local RadioShack store has a wide variety of antennas. For more information, see “Connecting an Antenna” on Page
6.
We recommend you record your CB’s serial number here. The number is on the CB’s bottom cabinet.
Serial Number _________________
2
© 1998 Tandy Corporation.
All Rights Reserved.
RadioShack is a registered trademark used by Tandy Corporation.
21-1703.fm Page 3 Wednesday, June 2, 1999 4:35 PM
FCC INFORMATION
The Federal Communications Commission (FCC) does not require you to have a license to operate this CB radio. However, you must know Part 95 of
FCC
Rules
. It explains the proper operation of a Class D citizen’s band transceiver. We enclosed a copy of Part 95 with your CB radio.
Warning: Do not open the CB radio to make any internal adjustments. A CB radio is set up to transmit a regulated signal on an assigned frequency. It is against the law to alter or adjust the settings inside the unit to exceed these limitations.
To be safe and sure:
• Never open your CB radio’s case.
• Never change or replace anything in your CB radio.
Your CB radio might cause TV or radio interference even when it is operating properly. To determine whether your CB is causing the interference, turn off your
CB. If the interference goes away, your
CB is causing it. Try to eliminate the interference by:
• moving your CB radio away from the receiver
• contacting your local RadioShack store for help
This device complies with Part 15 of
FCC Rules
. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
3
4
21-1703.fm Page 4 Wednesday, June 2, 1999 4:35 PM
CONTENTS
Installation ............................................................................................................... 5
Attaching the Microphone Holder ....................................................................... 5
Mounting the Transceiver .................................................................................... 5
Connecting an Antenna ...................................................................................... 6
Connecting the Microphone ................................................................................ 7
Connecting an External Speaker ........................................................................ 8
Using Vehicle Battery Power .............................................................................. 8
Using the Transceiver as a Base Station ............................................................ 9
Operation ............................................................................................................... 10
Receiving Transmissions and Adjusting Squelch ............................................. 10
Transmitting ...................................................................................................... 11
Selecting the Emergency Channel ................................................................... 11
Operational Hints .................................................................................................. 12
Common Uses for a CB .................................................................................... 12
Personal Uses ............................................................................................ 12
Business Uses ........................................................................................... 12
Transmission Courtesy ..................................................................................... 12
Using Common 10-Codes ................................................................................ 13
Maximum Range .............................................................................................. 14
Troubleshooting .................................................................................................... 15
Reducing Noise ................................................................................................ 16
Care and Maintenance .......................................................................................... 17
Replacing the Fuse ........................................................................................... 18
Specifications ........................................................................................................ 19
21-1703.fm Page 5 Wednesday, June 2, 1999 4:35 PM
INSTALLATION
ATTACHING THE
MICROPHONE HOLDER
You can attach the microphone holder to either side of the transceiver or to another location in your vehicle.
To attach the holder to either side of the transceiver, secure the holder to the side using the supplied screws, washers, and lock washers.
Note: If you cannot reach behind the mounting surface to attach the nuts on the machine screws, use the supplied 3 mm plain washers and self-tapping screws.
To attach the holder to another location in the vehicle, such as the dashboard, follow these steps.
1. Using the holder as a template, mark the positions for the mounting screw holes at the desired location.
2. At each marked position, drill a hole slightly smaller than the supplied mounting screws.
Caution: Be careful not to drill into anything behind the mounting surface.
3. Attach the holder at the mounting location using the supplied 3 mm machine screws, spring washers, plain washers, and nuts.
MOUNTING THE
TRANSCEIVER
The most common mounting location for this CB is under a vehicle’s dashboard.
However, if you plan to use the TRC-
503 as a base station, you can place it on a desk, shelf, or table (see “Using the
Transceiver as a Base Station” on Page
9).
If you are mounting the CB in a vehicle, choose a location where:
• You can easily reach the CB.
• Wires and cables are clear of the vehicle’s pedals or other moving parts.
• The CB is not directly in front of heating vents.
• All wires and cables can reach their connection points.
5
21-1703.fm Page 6 Wednesday, June 2, 1999 4:35 PM
Cautions:
• If you use the CB in a vehicle, mount it securely to avoid damage to the
CB or vehicle or injury to anyone in the vehicle during sudden starts or stops.
• Do not mount the CB where it could damage or interfere with the operation of any passive restraint safety device (an airbag or seat belt).
Follow these steps to mount the CB using the supplied hardware.
1. Using the mounting bracket as a template, mark the positions for the screw holes on the mounting surface.
Note: If you cannot reach behind the mounting surface to attach the nuts on the bolts, use the supplied 6 mm bolts and plain washers to secure the bracket.
4. Attach the CB to the mounting bracket using the supplied rubber washers and mounting knobs.
6
2. In each marked location, drill a hole slightly smaller than the supplied mounting screws.
Caution: Be careful not to drill into objects behind the mounting surface.
3. Mount the bracket to the mounting surface with the supplied 6 mm bolts, spring washers, plain washers, and nuts.
CONNECTING AN
ANTENNA
There are many different types of CB antennas for mobile CBs. Each type has its own benefits, so choose the one that best meets your needs. Your local RadioShack store sells a wide variety of antennas.
Note: If you are using this CB as a base station, see “Using the Transceiver as a
Base Station” on Page 9.
21-1703.fm Page 7 Wednesday, June 2, 1999 4:35 PM
When you choose an antenna, keep in mind that, for the best performance, you should mount the antenna:
• as high as possible on the vehicle
• as far as possible from sources of electrical noise
• vertically
Once you choose an antenna, follow its mounting instructions. Then route the cable to the transceiver and connect the cable to the ANTENNA jack on the back of the transceiver.
Follow the instructions supplied with the
SWR meter and antenna to adjust your antenna’s SWR to the lowest possible value. SWR values of 2.0:1 are generally acceptable, with readings of 1.5:1 or lower being more desirable.
CONNECTING THE
MICROPHONE
1. Press the tab on the side of the supplied microphone’s plug and insert the plug into the MIC jack on the front of the transceiver. Be sure the tab is aligned with the jack’s notch.
Tab Notch
2. Slide the microphone onto the microphone holder.
Cautions:
• Avoid routing the cable next to sharp edges or moving parts, which might damage the cable.
• Do not run the cable next to power cables or other radio antenna cables.
• Do not run the cable through the engine compartment or other areas that produce extreme heat.
To take advantage of your radio’s maximum range, adjust the antenna’s Standing Wave Ratio (SWR) using an SWR meter (not supplied).
To disconnect the microphone from the transceiver, press the tab on the side of the plug. Then pull out the plug.
Caution: Never pull on the microphone cable.
7
21-1703.fm Page 8 Wednesday, June 2, 1999 4:35 PM
CONNECTING AN
EXTERNAL SPEAKER
You can connect your transceiver to an external CB speaker, so you can hear an incoming call when you are outside your vehicle.
The external speaker you use with the transceiver should have an impedance of 8 ohms and be able to handle 3 to 10 watts of power, such as RadioShack
Cat. No. 21-549. The speaker cable must have a
1
/
8
-inch (3.5-mm) plug.
To connect the external speaker to the transceiver, insert the speaker cable’s plug into the EXT SPEAKER jack on the back of the CB.
To an 8-ohm,
3- to 10-Watt
Speaker
Note: When you connect an external speaker, the CB’s internal speaker disconnects.
USING VEHICLE BATTERY
POWER
Follow these steps to connect the transceiver to vehicle battery power.
Black Wire to Ground
Red Wire to
Switched
Accessory
Terminal
1. Connect the red wire (with the inline fuse holder) on the back of the transceiver to a point in your vehicle’s fuse block that has power only when the ignition is in the ACC
(accessory) or ON position.
2. Connect the black wire to a metal part of the vehicle’s frame (chassis ground).
Caution: Do not connect the black wire to a non-metallic (plastic) part, or to any part insulated from the vehicle’s chassis by a non-metallic part.
8
21-1703.fm Page 9 Wednesday, June 2, 1999 4:35 PM
USING THE TRANSCEIVER
AS A BASE STATION
Although this transceiver is designed mainly for mobile use, you can also use it as a base station with an AC power source. For base station installation, you need these items:
• a 13.8-volt DC power supply that can supply at least 1.5 amps (such as Cat. No. 22-504)
Caution: Most 13.8-volt DC power supplies plug into a standard AC outlet to produce DC power. Before connecting your CB to a 13.8-volt
DC power supply, read and follow the instructions included with the power supply.
• base station antenna (such as Cat.
No. 21-989)
• coaxial antenna cable and connector (available at your local RadioShack store)
Warning: Use extreme caution when you install or remove a base station CB antenna. If the antenna starts to fall, let it go! It could contact overhead power lines. If the antenna touches a power line, contact with the antenna, mast, cable, or guy wires can cause electrocution and death. Call the power company to remove the antenna. Do not attempt to do so yourself!
Follow these steps to install the CB as a base station.
Antenna
Black Wire to Negative
Terminal of
DC Power
Supply
Red Wire to Positive
Terminal of
DC Power
Supply
Mount the base station antenna as described in its owner’s manual.
1. Connect the antenna to the
ANTENNA jack on the back of the
CB.
2. Connect the transceiver’s black power wire to the negative (–) terminal on the DC power supply.
3. Connect the transceiver’s red wire
(with the in-line fuse) to the positive
(+) terminal on the DC power supply.
4. Connect the DC power supply to a standard AC outlet.
Caution: To prevent damage to the CB, be sure you connect both an antenna and the microphone before you use the
CB.
9
21-1703.fm Page 10 Wednesday, June 2, 1999 4:35 PM
OPERATION
Before you use your CB, you should know how to use it effectively and courteously. “Operational Hints” on Page 12 contains information that will help you get more enjoyment from your CB.
3. Set OUT CH9 CH19 to OUT to select a channel other than an emergency channel.
RECEIVING
TRANSMISSIONS AND
ADJUSTING SQUELCH
1. Turn SQUELCH fully counterclockwise.
4. Rotate the channel selector until the display shows the desired channel.
2. Turn on the transceiver by turning
VOLUME clockwise until it clicks. The channel display lights and the channel appears, and the RX indicator lights.
5. Adjust VOLUME to a comfortable listening level.
6. To cut out background noise between transmissions, wait until there is no signal, then slowly turn
SQUELCH clockwise until the background noise stops.
Note: To receive very weak signals, turn SQUELCH counterclockwise.
You hear noise between transmissions, but you also hear weak transmissions (those not strong enough to break through a higher squelch setting).
7. To turn off the CB, turn VOLUME counterclockwise until you hear it click. The display and indicators turn off.
10
21-1703.fm Page 11 Wednesday, June 2, 1999 4:35 PM
TRANSMITTING
Note: We recommend you try receiving before you transmit.
1. Follow Steps 1–5 in “Receiving
Transmissions and Adjusting
Squelch.”
2. To transmit, hold down PUSH TO
TALK on the microphone. The TX indicator lights. Hold the microphone
2–3 inches from your mouth and speak in a normal tone of voice, then release PUSH TO TALK when you finish. The TX indicator turns off.
PUSH
TO
TALK
SELECTING THE
EMERGENCY CHANNEL
Important: Channel 9 and Channel 19 are reserved for motorist assistance and for reporting emergency information about accidents, hazardous road conditions, and so on. Always give emergency messages priority on Channel 9 or
Channel 19.
To select the emergency Channel 9 or
Channel 19, set OUT CH9 CH19 to CH9 or CH19 . The selected channel number flashes on the display.
3. To turn off the CB, turn VOLUME counterclockwise until you hear it click. The display and RX indicator turn off.
To select another channel, set OUT CH9
CH19 to OUT . The previously selected channel number appears on the display.
11
21-1703.fm Page 12 Wednesday, June 2, 1999 4:35 PM
OPERATIONAL HINTS
Like most activities, CB radio has its customs and courtesies. The following tips will help you get the most enjoyment from your CB.
COMMON USES
FOR A CB
Personal Uses
• Keep in touch with home while driving to work, to the store, or to a social activity. Let your family know you are tied up in traffic or that you will stop by the store on the way home.
• If you are a two-car (or more) family,
CB radios are great for communicating with family members while they are in their cars.
• Contact friends or neighbors —find out “what’s happening” or plan a get-together.
• Ever have car trouble or run out of gas on the highway? What an assurance it is to be able to radio for assistance!
• Camping, fishing, and other sports are more fun with a CB radio. Locate a buddy or find out “what’s cooking” back at camp.
• Truck drivers and delivery personnel can learn road and traffic conditions and get assistance in locating destinations. A CB radio is also good company on those “long hauls.”
• On construction crews, a CB radio quickly pays for itself when you are calling for additional materials or coordinating the activities of different work crews.
TRANSMISSION
COURTESY
Please follow these guidelines of radio courtesy when using your CB.
• Wait for a pause in someone else’s transmission before you ask for a break.
• If you do not receive an answer to your call after a second attempt, sign off and wait several minutes before trying again.
• Do not hold down PUSH TO TALK when you are not talking. (This is called
dead keying
.)
• Assist callers with directions, information about road conditions, and any other reasonable requests.
Business Uses
• For security officers, a CB is more than a convenience — it is a must for both safety and efficiency.
12
21-1703.fm Page 13 Wednesday, June 2, 1999 4:35 PM
USING COMMON 10-
CODES
Citizen’s band operators and CB radio users have largely adopted the 10codes for standard questions and answers. These codes permit faster communication and better intelligibility in noisy areas.
This table lists codes adopted by the Associated Public Safety Communications
Officers (APCO).
Code Meaning
10-1
10-2
10-3
10-4
10-5
10-6
10-7
10-8
Your signal is bad.
Your signal is good.
Stop transmitting.
Message received and understood.
Relay information to _____.
I am busy or are you busy?
Out of service.
In service.
10-9 Repeat last message.
10-10 Negative (NO).
10-11 _____ in service.
10-12 Stand by.
10-13
Report road/weather conditions.
10-14 Information.
10-15 Message delivered.
Code Meaning
10-16 Reply to message.
10-17 En route.
10-18 Urgent.
10-19 Contact _____.
10-20 What is your location?
10-21 Call _____ by telephone.
10-22 Cancel last message.
10-23 Arrived at the scene.
10-24 Assignment complete.
10-25 Meet _____.
10-26
Estimated time of arrival is
_____.
10-30 Use caution.
10-31 Pick up.
10-33
Emergency traffic. Clear the channel.
10-34 What time is it?
10-41 Switch to Channel xx.
10-62 Cannot understand.
Note: Although this table lists the 10codes’ meanings in the form of a statement, they can also be phrased as questions (10-6: Are you busy?, 10-20:
What is your location?).
13
21-1703.fm Page 14 Wednesday, June 2, 1999 4:35 PM
MAXIMUM RANGE
The maximum range and quality of CB radio transmissions vary depending on the following conditions:
• the type and quality of antenna used
• the height of the antenna’s mounting location — the higher the antenna, the better the signal’s range
• the surrounding terrain — mountains and tall buildings limit the range
• weather conditions
• the number of nearby radios operating on the same channel
• standing wave ratio (SWR) between the antenna and the CB
Note: Your CB radio’s transmission range is generally line-of-sight.
14
21-1703.fm Page 15 Wednesday, June 2, 1999 4:35 PM
TROUBLESHOOTING
If your CB is not working as it should, follow these suggestions to see if you can eliminate the problem. If you cannot, take the CB to your local RadioShack store for assistance.
Symptom Check/Try
CB has trouble receiving.
Turn transceiver power on.
Microphone connected? Secure connections.
Antenna connected? Secure connections.
Too much squelch? Adjust as needed.
Radio not on operating channel? Switch to an active channel.
PUSH TO TALK held down? Release PUSH TO TALK .
CB has trouble transmitting.
Adjust VOLUME .
Turn transceiver power on.
Antenna connected? Secure connections.
All connections free of corrosion? Clean and tighten.
Microphone connector loose? Firmly press in jack.
Radio not on operating channel? Switch to an active channel.
PUSH TO TALK fully pressed? Press completely.
Radio does not work at all. Power connected? Secure connections.
Microphone connected? Secure connections.
Fuse needs replacing? Replace with identical fuse.
See “Replacing the Fuse” on Page 18.
Cannot select a channel.
Set OUT CH9 CH19 to OUT .
PUSH TO TALK pressed? Release PUSH TO TALK .
15
21-1703.fm Page 16 Wednesday, June 2, 1999 4:35 PM
REDUCING NOISE
Because your CB is exceptionally quiet, any noise you hear is probably from an external source in your vehicle such as the alternator, another radio or spark plugs.
The transceiver uses an ANL (Automatic
Noise Limiter) circuit to reduce noise.
However, if possible, try to eliminate the noise by finding its source.
You can determine the noise’s source by turning off the engine and operating the CB with your vehicle’s ignition set to
ACC. If the noise is reduced, the problem is in your vehicle’s ignition or electrical system.
Here are a few hints to help you reduce or eliminate such noise.
• Make all CB power and antenna wires as short as possible.
• Route the power wires away from the antenna wires.
• Be sure that the chassis ground connection is secure.
• Replace old ignition wires with new, high-voltage, noise suppression wires.
• Install noise suppressors on your spark plugs, or install new spark plugs that have built-in noise suppressors.
• If problems persist, check your alternator/generator and regulator gauges. You can reduce the noise from these sources by using bypass capacitors at the various output voltage points.
Your local RadioShack store has a wide selection of noise suppression accessories.
16
21-1703.fm Page 17 Wednesday, June 2, 1999 4:35 PM
CARE AND MAINTENANCE
Your RadioShack TRC-503 40 Channel Mobile CB Radio with Channel 9/19 Priority
Switch is an example of superior design and craftsmanship. The following suggestions will help you care for your CB so you can enjoy it for years.
Keep the CB dry. If it gets wet, wipe it dry immediately. Liquids can contain minerals that can corrode electronic circuits.
Handle the CB gently and carefully. Dropping it can damage circuit boards and cases and can cause the CB to work improperly.
Use and store the CB in normal temperature environments. Temperature extremes can shorten the life of electronic devices and distort or melt plastic parts.
Keep the CB away from dust and dirt, which can cause premature wear of parts.
Wipe the CB with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the CB.
Modifying or tampering with the CB’s internal components can cause a malfunction and might invalidate its warranty and void your FCC authorization to operate it. If your
CB is not performing as it should, take it to your local RadioShack store for assistance.
17
21-1703.fm Page 18 Wednesday, June 2, 1999 4:35 PM
REPLACING THE FUSE
The TRC-503’s 2-amp in-line fuse helps protect your CB from power surges and short circuits. When replacement is required, use a 2-amp, slow-blow glass fuse, such as Cat. No. 270-1023.
Caution: Do not use a fuse with ratings other than those specified here. Doing so might damage your CB.
Follow these steps to replace the fuse.
1. Make sure the power source and CB are both off.
2. Hold the fuse holder by both ends, push the ends together, twist one end counterclockwise, then pull them apart.
3. Remove the old fuse and inspect its condition. If it is blown, insert a new one of the same type and rating. If it is not blown, reinsert it.
4. Push the fuse holder ends together and twist one end clockwise.
18
21-1703.fm Page 19 Wednesday, June 2, 1999 4:35 PM
SPECIFICATIONS
RECEIVER
Frequency Coverage ................... All 40 CB Channels (Class D) 26.965–27.405 MHz
Sensitivity for 10dB S/N .................................................................................... 0.6
µ
V
Squelch Sensitivity at Tight .................................................................... 350–2820
µ
V
Overall Audio Fidelity for 450–2500 Hz .............................................................. –6 dB
Maximum Audio Output Power ....................................................................... 6 Watts
Cross Modulation ............................................................................................... 50 dB
TRANSMITTER
Frequency Coverage ................... All 40 CB Channels (Class D) 26.965–27.405 MHz
Frequency Tolerance .................................................................................... ± 1300 Hz
Carrier Power at No Modulation ...................................................................... 4 Watts
Spurious Emission ........................................................................................... –67 dB
Current Drain at No Modulation .................................................................... 1300 mA
Modulation Frequency Response for 450–2500 Hz ........................................... –6 dB
Microphone Sensitivity for 50% Modulation ........................................................ 2 mV
GENERAL
Power Requirements ................................................ 13.8 Volts DC, Negative Ground
Dimensions (HWD) ............................... 1
3
/
8
×
4
1
/
4
×
5
7
/
8
inches (35
×
108
×
150 mm)
Weight ............................................................................................... 1 lb 6 oz (640 g)
Included Accessories ..................................... Microphone Hanger, Mounting Bracket
Specifications are typical, individual units might vary. Specifications are subject to change and improvement without notice.
19
21-1703.fm Page 20 Wednesday, June 2, 1999 4:35 PM
8A8N
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack companyowned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-
ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-
VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
811081340A
Printed in China
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement