Model No. PETL61606.0
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts,
please call:
08457 089 009
or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
email: csuk@iconeurope.com
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
USER'S MANUAL
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
HOW TO USE THE CHEST PULSE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING is attached in the center of this manual.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least 2.5 m (8 ft.) of clearance behind it and
0.5 m (2 ft.) on each side. Do not place the
treadmill on a surface that blocks any air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
13. Keep the power cord and the surge suppressor away from heated surfaces.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 26 if the treadmill is not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 13).
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
7. The treadmill should be used only by persons
weighing 159 kg (350 lbs.) or less.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
8. Never allow more than one person on the
treadmill at a time.
18. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the on/off switch
to the off position when the treadmill is not in
use. (See the drawing on page 5 for the location of the on/off switch.)
10. When connecting the power cord (see page
11), plug the power cord into an earthed circuit. No other appliance should be on the
same circuit. When replacing the fuse, an
ASTA approved BS1362 type should be fitted
to the fuse carrier. A 13 amp fuse should be
used.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 24.) You
must be able to safely lift 20 kg (45 lbs.) to
raise, lower, or move the treadmill.
11. If an extension cord is needed, use only a 3conductor, 1mm2 (14-gauge) cord that is no
longer than 1.5 m (5 ft.).
3
21. Do not change the incline of the treadmill by
placing objects under the treadmill.
25.
DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
22. When folding or moving the treadmill, make
sure that the frame is held securely by the pin
on the latch knob.
23. Inspect and properly tighten all parts of the
treadmill regularly.
24. Never insert or drop any object into any
opening.
26. The treadmill is intended for in-home use
only. Do not use the treadmill in a commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the
treadmill. If a decal is missing or illegible, call
the telephone number on the front cover of this
manual and request a free replacement decal.
Apply the decal in the location shown. Note:
The decals may not be shown at actual size.
4
BEFORE YOU BEGIN
Thank you for selecting the revolutionary PROFORM®
620 V treadmill. The 620 V treadmill offers an impressive selection of features designed to make your workouts at home more enjoyable and effective. And when
you’re not exercising, the unique 620 V treadmill can
be folded up, requiring less than half the floor space of
other treadmills.
ing this manual, please see the front cover of this manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number of the treadmill is PETL61606.0. The
serial number can be found on a decal attached to the
treadmill (see the front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fan
TV Console
Book Holder
Accessory Tray
Handrail
Key/Clip
Pulse Sensor
Circuit Breaker
On/Off Switch
Walking Belt
Foot Rail
Cushioned
Walking Platform
Rear Roller
Adjustment Bolts
5
4 1/2” Bolt (78)–4
ension Leg
t (106)–4
ew (123)–2
ASSEMBLY
Wash
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
3/4” Tek Screw (58)–4
dispose of the packing materials until assembly is completed.
1/2” Silver Screw
(48)–1
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
(60)–2
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. Spacer
This is aScrew
normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex key
and your own phillips screwdriver
. For help
identifying the assembly hardware, see the drawings below. The number in parentheses below each drawing
is the key number of the part, from the PART LIST on pages 30 and 31. The number following the parentheses is
the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part is not in
the parts bag, check to see if it has been preassembled. To avoid damaging plastic parts, do not use
power tools for assembly.
3/4” Schraube (4)–4
Haltestangenschraube (64)–6
Pfosten-Zahnscheibe
(90)–10
Pfostenschraube (72)–4
1. Make sure that the power cord is unplugged.
1
With the help of a second person, lift the front of
the treadmill and insert the crossbar on the Base
(83) into the cutout in the cardboard stand as
shown at the right. Have the second person
securely hold the cardboard stand and the
treadmill until assembly step 2 is completed.
Lower Latch Bolt (XX)–1
Upper Latch Bolt (XX)–1
Serious injury
may occur if the treadmill moves forward or backward and falls off the cardboard stand. A second person must securely hold the cardboard stand and the
treadmill until assembly step 2 is completed to prevent the treadmill from
moving, tipping, or falling.
Nut (38)–2
WARNING:
6
Console Bolt (72)–4
83
Cardboard
Stand
2. Identify the Left Upright (73) and the Right
Upright (74). Hold the Right Upright near the
Right Base Cover (77) as shown. Insert the
Upright Wire Harness (75) up through the rectangular hole in the bottom of the Right Upright
and out of the top of the Right Upright.
2
73
Gently pull up on the Upright Wire Harness (75)
as you set the Right Upright (74) on the Base
(83) inside the Right Base Cover (77). Be careful not to pinch the Upright Wire Harness.
75
74
Attach the Right Upright (74) to the Base (83)
with two Upright Bolts (72) and two Star
Washers (90). Note: It may be necessary to tip
the top of the Right Upright forward slightly as
you thread the Upright Bolts into the Right
Upright.
77
83
Attach the Left Upright (73) to the Base (83) in
the same way. Note: There is not an upright wire
harness on the left side.
90
With the help of a second person, lower the
treadmill and discard the cardboard stand.
72
3. Identify the Right Upright Sleeve (96) and the
Left Upright Sleeve (95). Slide the Right Upright
Sleeve onto the Right Upright (74) and the Left
Upright Sleeve onto the Left Upright (73).
3
95
73
“Left”
“Right”
96
74
7
4. With the help of a second person, hold the console assembly near the Uprights (73, 74).
4
Console
Assembly
Connect the Upright Wire Harness (75) to the
Console Wire Harness (71). Make sure to connect the connectors properly (see the inset
drawing). The connectors should slide together easily and snap into place. If they do
not, turn one connector and try again. IF THE
CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAMAGED WHEN THE POWER IS TURNED ON.
73
71
75
75
5. Insert the brackets on the Handrails (99) into the
Right Upright (74) and the Left Upright (73).
Make sure that no wires are pinched.
71
74
5
99
99
73
74
6. Finger tighten three Handrail Bolts (64) with
three Star Washers (90) into the Right Upright
(74). Next, finger tighten three Handrail Bolts
with three Star Washers (not shown) into the
Left Upright (73). Then, firmly tighten all six
Handrail Bolts.
6
73
64
90
90
64
8
74
7. Slide the Right Upright Sleeve (96) against the
console assembly. Attach the Right Upright
Sleeve with two 3/4" Screws (4).
7
Attach the Left Upright Sleeve (not shown) to the
Left Upright (73) in the same way.
73
4
96
4
74
8. Make sure that all parts are properly tightened before you use the treadmill. Keep the included hex key
in a secure place; the hex key is used to adjust the walking belt (see page 27). To protect the floor or carpet
from damage, place a mat under the treadmill.
9
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
The chest pulse sensor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
the hole in one end of the sensor unit, as shown in the
inset drawing. Press the end of the sensor unit under
the buckle on the chest strap. The tab should be flush
with the front of the sensor unit.
• Do not expose the chest pulse sensor to direct sunlight for extended periods of time; do not expose it to
temperatures above 50° C (120° F) or below -10° C
(15° F).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Chest Strap
Tabs
Tab
Sensor Unit
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
Sensor
Unit
Buckle
Next, wrap the chest
pulse sensor around
your chest and attach
the other end of the
chest strap to the
sensor unit. Adjust
the length of the
chest strap, if necessary. The chest pulse
sensor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
Next, pull the sensor unit away from your body a few
inches and locate the two electrode areas on the inner
side (the electrode areas are covered by shallow
ridges). Using saline solution such as saliva or contact
lens solution, wet both electrode areas. Return the
sensor unit to a position against your chest.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than necessary, draining the battery prematurely.
CHEST PULSE SENSOR TROUBLESHOOTING
The instructions on the following pages explain
how the chest pulse sensor is used with the console. If the chest pulse sensor does not function
properly, try the steps below.
• Make sure that you are wearing the chest pulse sensor as described at the left. Note: If the chest pulse
sensor does not function when positioned as described, move it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the sensor
unit. If heart rate readings do not appear until you
begin perspiring, rewet the electrode areas.
• As you walk or run on the treadmill, position yourself near the center of the walking belt. For the console to display heart rate readings, the user must
be within arm’s length of the console.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical conditions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
• The operation of the chest pulse sensor can be affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
• The CR2032 battery may need to be replaced (see
page 28).
10
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear.
HOW TO PLUG IN THE POWER CORD
This product must be earthed. If it should malfunction or break
down, earthing provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped
with a power cord having an equipment-earthing conductor and an
earthing plug. Important: If the power cord is damaged, it must
be replaced with a manufacturer-recommended power cord.
1
Socket on treadmill
See drawing 1. Plug the indicated end of the power cord into the
socket on the treadmill.
See drawing 2. Press the pins on the power cord into the metal clips
in the adapter as shown. Close the adapter cover over the end of the
power cord and tighten the screw in the adapter. Important: Make
sure that the adapter cover is secure and the screw has been
tightened before using the power cord.
FR/SP
2
Adapter
Cover
Screw
Pins
Adapter
See drawing 3. Plug the power cord into an appropriate outlet that is
properly installed and earthed in accordance with all local codes and
ordinances. Important: The treadmill is not compatible with
GFCI-equipped outlets.
3
FR/
Metal
Clips
Outlet
IT
DANGER:
Improper connection of the equipment-earthing conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as
to whether the product is properly earthed. Do not modify the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed by a qualified electrician.
FR/SP
11
GR
IT
FEATURES OF THE CONSOLE
with the 8-week Weight Loss program, or train for a
long-distance run with the Marathon program. iFIT programs automatically control the treadmill while the
voice of a personal trainer coaches you and motivates
you through every step of your workout. One iFIT Card
is included. Additional iFIT Cards are available separately. To purchase iFIT Cards at any time, call the
telephone number on the front cover of this manual.
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable. When the manual mode of the console is selected, the speed and incline of the treadmill
can be changed with the touch of a button. As you exercise, the console will display continuous exercise
feedback. You can even measure your heart rate using
the handgrip pulse sensor or the chest pulse sensor.
You can even listen to your favorite workout music or
audio books with the console’s premium stereo sound
system while you get in shape.
In addition, the console features twenty-four preset programs — twelve weight loss programs and twelve aerobic fitness programs. Each program automatically controls the speed and incline of the treadmill as it guides
you through an effective workout. You can even create
your own custom programs and save them for future
use. The console also offers four pulse programs that
control the speed and incline of the treadmill to help
you keep your heart rate near target heart rate settings.
To turn on the power, follow the steps on page 13. To
personalize console settings, follow the steps on page
13. To use the manual mode, see page 15. To use a
preset program, see page 17. To create and use a
custom program, see pages 19 and 20. To use a
pulse program, see page 21. To use the stereo
sound system, see page 22. To use an iFIT card,
see page 23.
The console also features the new iFIT Interactive
Workout system. The iFIT system enables the console
to accept iFIT Interactive Workout Cards containing
workout programs designed to help you achieve specific fitness goals. For example, lose unwanted pounds
Note: If there is a sheet of clear plastic on the console,
remove the clear plastic.
12
HOW TO TURN ON THE POWER
1
2
Plug in the power cord
(see page 11). Next,
locate the on/off switch
on the treadmill frame
near the power cord.
Make sure that the
on/off switch is in the
on position.
On
Position
HOW TO PERSONALIZE CONSOLE SETTINGS
The console also features a settings mode that allows
you to view your workout history, select a system of
measurement for the console, turn on and turn off the
demo mode, enter an audio trainer setting, adjust the
volume and contrast settings of the console, and turn
on and turn off the welcome screen.
Follow the steps below to personalize console settings.
Stand on the foot
rails of the treadClip
mill. Find the clip
attached to the
key, and slide the
Key
clip securely onto
the waistband of
your clothes. Next,
insert the key into the console. After a moment,
the display will light. Important: In an emergency
situation, the key can be pulled from the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few
steps backward; if the key is not pulled from
the console, adjust the position of the clip.
1
Select the settings mode.
To select the settings mode, first remove the key
from the console. Then, hold down the Stop button while reinserting the key into the console.
When the settings mode is selected, the top of the
display will show the total number of hours that the
treadmill has been used and the total number of
miles or kilometers that the walking belt has
moved.
Below the workout history, the display will show
the word ENGLISH or METRIC to indicate which
system of measurement is selected. To change
the system of measurement, first highlight UNITS
by pressing the Heart Rate increase or decrease
button, and press the Heart Rate Control button.
Next, press the Heart Rate increase or decrease
button to select the desired system of measurement. Then, press the Heart Rate Control button.
Note: To prevent damage to the walking platform,
wear clean athletic shoes while using the treadmill. The first time the treadmill is used, observe
the alignment of the walking belt, and center the
walking belt if necessary (see page 27).
The display will also show the words DEMO
MODE and the current setting: OFF, LOGO,
ROAD, or PROGRAMS. The “demo mode” can be
used while the treadmill is displayed in a store.
While the demo mode is selected, the power cord
can be plugged in, the key can be removed from
the console, and the display will remain on. The
console buttons will not function. To select a
demo mode, highlight DEMO MODE and then
press the Heart Rate Control button. Next, press
the Heart Rate increase or decrease button to
highlight OFF (to turn off the demo mode), VISUAL
EQ (to display visual equalizer), ROAD (to display
an animation of a runner on a road), or PROGRAMS (to display previews of various programs).
Then, press the Heart Rate Control button.
13
You can select an audio setting if desired. When
you use an iFIT Card, a personal trainer will guide
you through your workouts and instruct you how
to purchase more iFIT Cards if “Instruction” is selected as your audio setting. If you select the “On”
setting, your personal trainer will simply guide you
through your iFIT workouts. If you select “Off,” you
will hear no audio guidance during your workouts.
To change the audio setting, first highlight AUDIO
TRAINER and press the Heart Rate Control button. Next, press the Heart Rate increase or decrease button to select the desired audio setting.
Then, press the Heart Rate Control button.
CONTRAST and press the Heart Rate Control
button. Next, press the Heart Rate increase and
decrease buttons to select a contrast setting.
Then, press the Heart Rate Control button.
You can also select an equalizer setting to optimize the sound of your personal music. Choose
among DEFAULT, CLASSIC, COUNTRY,
TECHNO, or ROCK. To select an equalizer setting, first highlight EQUALIZER and press the
Heart Rate Control button. Next, press the Heart
Rate increase and decrease buttons to select an
equalizer setting. Then, press the Heart Rate
Control button.
You can adjust the volume of your personal
trainer’s voice by highlighting VOLUME, pressing
the Heart Rate Control button, and then pressing
the Heart Rate increase and decrease buttons to
select a volume setting. Then, press the Heart
Rate Control button.
2
When you are finished using the settings
mode, remove the key.
To exit the settings mode at any time, remove the
key from the console.
The contrast of the display can also be adjusted.
To adjust the contrast of the display, first highlight
14
5
HOW TO USE THE MANUAL MODE
1
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of
the numbered Quick Incline buttons. Each time
one of the buttons is pressed, the incline will gradually increase until it reaches the selected incline
setting.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2
Personalize console settings if desired.
6
See HOW TO PERSONALIZE CONSOLE SETTINGS on page 13.
3
Select a display mode and monitor your
progress with the display and the intensity
level bar.
As you walk or run on the treadmill, the display
can show the following workout information:
Select the manual mode.
Each time the key is inserted, the manual mode
will be selected. If you have selected a program,
press any of the program buttons repeatedly until
the word MANUAL appears in the display. Note:
Make sure that an iFIT card is not inserted into the
iFIT slot.
4
Change the incline of the treadmill as desired.
Start the walking belt and adjust the speed.
To start the walking belt, press the Start button,
the Speed increase button next to the Start button, or one of the numbered Quick Speed buttons.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 2
Km/H. As you exercise, change the speed of the
walking belt as desired by pressing the Speed increase and decrease buttons next to the Start button. Each time a button is pressed, the speed setting will change by 0.1 Km/H; if a button is held
down, the speed setting will change in increments
of 0.5 Km/H. If one of the numbered Quick Speed
buttons is pressed, the walking belt will gradually
increase in speed until it reaches the selected
speed setting.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
Quick Speed buttons.
15
•
The elapsed time.
•
The distance that you have walked or run.
•
The speed of the walking belt.
•
The incline level of the treadmill.
•
The approximate number of calories you have
burned.
•
Your walking or running pace, in minutes per
mile or minutes per kilometer.
•
A visual equalizer.
•
Your heart rate. Note: Your heart rate can be
displayed only while you use the handgrip
pulse sensor or the chest pulse sensor.
•
In addition, the display can show a “workout
history”—a profile that represents the speed
settings that you select during your workout. At
the beginning of each minute of your workout,
an additional column will appear in the profile;
as you increase or decrease the speed setting,
the height of the column will increase or decrease.
•
The display can also show an animation of a
runner on a road. As you increase or decrease
the speed setting, the runner will speed up or
slow down.
When the manual mode is selected, the console
offers eight display modes. The display mode that
you select will determine which workout information is shown. For example, the first display mode
shows only the elapsed time and the distance that
you have walked or run. Press the Display button
repeatedly to select the desired display mode.
7
Measure your heart rate if desired.
You can measure your heart rate using either the
chest pulse sensor (see page 10) or the handgrip
pulse sensor. Note: If you use the handgrip pulse
sensor and the chest pulse sensor at the same
time, the display will not show your heart rate accurately.
To use the
handgrip
pulse sensor,
first remove
the sheets of
clear plastic
from the metal
Contacts
contacts on
the handgrip
pulse sensor. Next, stand on the foot rails and
hold the metal contacts—avoid moving your
hands. When your pulse is detected, your heart
rate will appear in the display. For the most accurate heart rate reading, continue to hold the
contacts for about 15 seconds.
Regardless of which display mode you select, the
speed or incline setting will appear in the display
for a few seconds each time you change the setting. In addition, your heart rate will appear in the
display for up to 40 seconds each time you use the
handgrip pulse sensor or put on the chest pulse
sensor. Note: If you select the display mode shown
below, your heart rate will be shown in place of the
approximate exercise pace.
8
Turn on the fan if desired.
To turn on the fan at high speed, press the Fan
button. To turn on the fan at low speed, press the
button a second time. To turn off the fan, press
the Fan button again. Note: If the fan is on when
the walking belt stops, the fan will automatically
turn off after a few minutes.
As you exercise, the workout intensity level bar will
indicate the approximate intensity level of your exercise. For example, if eight of the indicators in the
bar are lit, the bar shows that your intensity level is
ideal for aerobic exercise.
9
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position or the treadmill will become damaged. Next,
remove the key from the console and put it in a secure place.
Workout Intensity Level Bar
To reset the console, press the Stop button, remove the key, and then reinsert the key.
When you are finished using the treadmill,
switch the on/off switch to the “off” position
and unplug the power cord.
16
At the end of the first one-minute segment of the
program, a series of tones will sound. If a different
speed setting and/or incline setting is programmed for the second segment, the speed setting and/or incline setting will appear at the top of
the display for a moment to alert you. The treadmill will then automatically adjust to the speed and
incline settings for the second segment.
HOW TO USE A PRESET PROGRAM
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2
Personalize console settings if desired.
See HOW TO PERSONALIZE CONSOLE SETTINGS on page 13.
3
Select a preset program.
To select a preset program, press the Weight
Loss Programs button or the Aerobic Fitness
Programs button repeatedly.
The program will continue in this way until the
small arrow reaches the right end of the profile.
The walking belt will then slow to a stop.
When a preset program is selected, the display
will show the name of the program, the program
time, the maximum incline setting of the program,
and the maximum speed setting. In addition, a
profile of the speed settings of the program will
appear in the display.
If the third display mode is selected, the display
will show an animation of a runner.
Each preset program is divided into 30 oneminute segments. One speed setting and one incline setting are programmed for each segment.
Note: The same speed setting and/or incline setting may be programmed for two or more consecutive segments.
4
At the end of the first one-minute segment of the
program, a series of tones will sound. If a different
speed setting is programmed for the second segment, the speed setting will move along the bottom of the display to alert you. If a different incline
setting is programmed, the incline setting will appear at the top of the display for a moment. The
treadmill will then automatically adjust to the
speed and incline settings for the second segment.
Press the Start button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
5
Select a display mode and monitor your
progress with the display.
The program will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.
When a preset program is selected, the console
offers three display modes. Press the Display button repeatedly to select the desired display mode.
If the first or second display mode is selected, a
profile of the speed settings of the program will appear in the display. A small arrow below the profile
will indicate your progress.
17
If the speed or incline setting for the current segment is too high or too low, you can override the
setting by pressing the Speed or Incline buttons;
however, when the next segment begins, the
treadmill will automatically adjust to the speed
and incline settings for the next segment.
7
See step 8 on page 16.
8
To change the intensity level of the entire program,
press the Intensity increase and decrease buttons.
When you are finished exercising, remove the
key from the console.
When the program ends, make sure that the incline of the treadmill is at the lowest setting.
Next, remove the key from the console and put it in
a secure place.
To stop the program at any time, press the Stop
button. To restart the program, press the Start button. The walking belt will begin to move at 2 Km/H.
When the next segment of the program begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
6
Turn on the fan if desired.
When you are finished using the treadmill,
switch the on/off switch to the “off” position
and unplug the power cord.
Measure your heart rate if desired.
See step 7 on page 16.
18
5
HOW TO CREATE A CUSTOM PROGRAM
1
When a custom program is selected, the console
offers three display modes. Press the Display button repeatedly to select the desired display mode.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2
To program a speed setting and an incline setting
for the first one-minute segment of the program,
simply adjust the speed and incline of the treadmill
as desired by pressing the Speed and Incline buttons or the Intensity buttons.
Personalize console settings if desired.
See HOW TO PERSONALIZE CONSOLE SETTINGS on page 13.
3
When the first segment ends, a series of tones will
sound and the current speed setting and the current incline setting will be saved in memory.
Select a custom program.
To select a custom program, press the Custom
Programs button once or twice.
Program a speed setting and an incline setting for
the second segment as described above. Continue
programming speed and incline settings for up to
30 segments.
If the custom program has not yet been defined, the display will show a program time of
three minutes. If the program time is more than
three minutes, see HOW TO USE A CUSTOM
PROGRAM on page 20.
Each custom program is divided into one-minute
segments. One speed setting and one incline setting can be programmed for each segment.
4
Select a display mode and program the
desired speed and incline settings.
When you are finished with your workout, press
the Stop button twice. The custom program will
then be saved in memory.
6
When you are finished exercising, remove the
key from the console.
Press the Start button to start the program.
See step 8 on page 18.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
19
5
HOW TO USE A CUSTOM PROGRAM
1
Insert the key into the console.
The custom program will function in the same way
as a preset program (see step 5 on pages 17 and
18).
See HOW TO TURN ON THE POWER on page
13.
2
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons or the Intensity buttons. When the
current segment ends, the new setting will be saved
in memory. To increase the length of the program, first wait until the program ends. Then, press
the Start button and program speed and incline settings for as many additional segments as desired;
custom programs can have up to 30 segments.
When you have added as many segments as desired, press the Stop button twice. To decrease
the length of the program, press the Stop button
twice at any time before the program ends.
Personalize console settings if desired.
See HOW TO PERSONALIZE CONSOLE SETTINGS on page 13.
3
Select a display mode and monitor your
progress with the display.
Select a custom program.
To select a custom program, press the Custom
Programs button once or twice.
When a custom program is selected, the display
will show the name of the program, the program
time, the maximum incline setting of the program,
and the maximum speed setting. In addition, a
profile of the speed settings of the program will
appear in the display.
6
Measure your heart rate if desired.
See step 7 on page 16.
Note: If the display shows a program time of
three minutes, see HOW TO CREATE A CUSTOM PROGRAM on page 19.
7
Turn on the fan if desired.
See step 8 on page 16.
Each custom program is divided into one-minute
segments. One speed setting and one incline setting are programmed for each segment.
4
8
Press the Start button to start the program.
When you are finished exercising, remove the
key from the console.
See step 8 on page 18.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
20
5
HOW TO USE A PULSE PROGRAM
To adjust the maximum target heart rate setting,
press the Heart Rate increase and decrease buttons (see EXERCISE INTENSITY on page 29). To
adjust the target heart rate setting quickly, hold
down one of the buttons.
CAUTION:
If you have heart problems, or if you are over 60 years of age and
have been inactive, do not use the pulse programs. If you are taking medication regularly,
consult your physician to find whether the
medication will affect your exercise heart rate.
6
Put on the chest pulse sensor.
7
Note: You must wear the chest pulse sensor to
use a pulse program (see page 10 for information
about using the chest pulse sensor).
2
Press the Start button to start the program.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Follow the steps below to use a pulse program.
1
Adjust the maximum target heart rate setting if
desired.
Select a display mode and monitor your
progress with the display.
When a pulse program is selected, the console offers two display modes. Press the Display button
to select the desired display mode.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
3
Personalize console settings if desired.
See HOW TO PERSONALIZE CONSOLE SETTINGS on page 13.
4
Regardless of which display mode you select, a
profile of the target heart rate settings of the program will appear in the display. A white line representing your heartbeat will also appear; each time a
heartbeat is detected, an additional peak will appear in the line. A small arrow below the profile will
indicate your progress.
Select a pulse program.
To select a pulse program, press the Heart Rate
Control button repeatedly.
During each one-minute segment of the program,
the console will compare your heart rate to the
current target heart rate setting. If your heart rate
is too far below or above the target heart rate setting, the speed of the walking belt or the incline of
the treadmill will automatically change to bring
your heart rate closer to the target heart rate setting. Each time the speed or incline changes, the
speed setting and the incline setting will appear at
the top of the display for a moment to alert you.
When a pulse program is selected, the display will
show the name of the program and the maximum
target heart rate setting of the program. In addition, a profile of the target heart rate settings of
the program will appear in the display.
When each segment ends, a series of tones will
sound.
The pulse programs are each divided into oneminute segments. During the first pulse program,
the same target heart rate setting is programmed
for all segments (except for the first two segments). During the second, third, or fourth pulse
program, one target heart rate setting is programmed for each segment. Note: The same target heart rate setting may be programmed for two
or more consecutive segments.
21
If the speed or incline setting for the current segment is too high or too low, you can override the
setting by pressing the Speed or Incline buttons;
however, when the console compares your heart
rate to the current target heart rate setting, the
speed or incline of the treadmill may automatically
change.
To stop the program at any time, press the Stop
button. To restart the program, press the Start button. The walking belt will begin to move at 2 Km/H.
When the console compares your heart rate to the
current target heart rate setting, the speed or incline of the treadmill may automatically change.
If the first pulse program is selected, the program
will continue until you stop it by pressing the Stop
button. If the second, third, or fourth pulse program is selected, the program will continue until
the small arrow reaches the right end of the profile. The walking belt will then slow to a stop.
8
HOW TO USE THE STEREO SOUND SYSTEM
To play music or audio books through the console’s
stereo speakers, you must connect your MP3 player,
CD player, or personal audio player to the console.
Locate the audio jack below the television on the console, and plug it into a jack on your MP3 player, CD
player, or personal audio player. Make sure that the
audio/video cable is fully plugged in.
Next, press the Play button on your MP3 player, CD
player, or personal audio player. Then, adjust the volume on your MP3 player, CD player, or personal audio
player. You can also adjust the volume on the console
by pressing the Volume (VOL) increase and decrease
buttons.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat surface instead of on the console.
Turn on the fan if desired.
See step 8 on page 16.
9
When you are finished exercising, remove the
key from the console.
See step 8 on page 18.
22
4
HOW TO USE AN IFIT CARD
1
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2
5
Personalize console settings if desired.
See HOW TO PERSONALIZE CONSOLE SETTINGS on page 13.
3
Press the Start button to start the program.
Select a display mode and monitor your
progress with the display and the intensity
level bar.
When an iFIT program is selected, the console offers three display modes (see step 6 on page 15).
Press the Display button repeatedly to select the
desired display mode. If the first or second display mode is selected, a profile of the speed settings of the program will appear in the display. A
small arrow below the profile will indicate your
progress.
Insert an iFIT Card and select a program.
To use an iFIT program, insert an iFIT Card into
the iFIT slot; make sure that the iFIT Card is oriented so the metal contacts are face-down and
are inserted into the iFIT slot.
During the program, the voice of a personal trainer
will guide you through the workout. You can adjust
the volume or select an audio setting for your personal trainer (see HOW TO PERSONALIZE CONSOLE SETTINGS on pages 13 and 14).
iFIT Slot
If the speed or incline setting for the current segment is too high or too low, you can override the
setting by pressing the Speed or Incline buttons or
the Intensity buttons; however, when the next segment begins, the treadmill will automatically adjust to the speed and incline settings for the
next segment.
iFIT Card
Next, select an iFIT program by pressing the
Heart Rate increase or decrease button. When an
iFIT program is selected, the display will show the
name of the program, the maximum incline setting
and the maximum speed setting of the program,
and the program time. In addition, a profile of the
speed settings of the program will appear in the
display.
To stop the program at any time, press the Stop
button. To restart the program, press the Start button. The walking belt will begin to move at 2 Km/H.
When the next segment of the program begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
6
Turn on the fan if desired.
See step 8 on page 16.
7
When you are finished exercising, remove the
key from the console.
See step 8 on page 18.
Each iFIT program is divided into several oneminute segments. One speed setting and one incline setting are programmed for each segment.
Note: The same speed setting and/or incline setting may be programmed for two or more consecutive segments.
CAUTION: Always remove iFIT Cards from the
iFIT slot when you are not using them.
23
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may become permanently damaged. Remove the key and unplug
the power cord. CAUTION: You must be able to safely lift
20 kg (45 lbs.) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the
chances of injury, do not lift the frame by the plastic
foot rails. To raise the frame, bend your legs, keep
your back straight, and lift with your legs. Raise the
frame about halfway to the vertical position.
Frame
2. Raise the frame until the latch knob locks into the storage
position. Make sure that the latch knob is locked in
the storage position.
Frame
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 30° C (85° F).
Latch Knob
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the latch
knob is locked in the storage position.
1. Hold the handrails and place one foot against one of the
wheels.
2. Tilt the treadmill backward until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it backward. To reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is resting in the storage position.
24
Handrails
Wheel
HOW TO LOWER THE TREADMILL FOR USE
Frame
1. Hold the upper end of the treadmill with your left hand.
Pull the latch knob to the left and hold it. Pivot the frame
downward and release the latch knob. Note: To release
the latch knob, it may be necessary to push the frame forward as you pull the latch knob to the left.
Latch Knob
2. Hold the metal frame firmly with both hands, and lower it
to the floor. CAUTION: To decrease the possibility of injury, do not lower the frame by gripping only the plastic
foot rails. Do not drop the frame to the floor. Make sure
to bend your legs and keep your back straight.
Frame
25
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 11). If an extension cord is needed, use only a 3-conductor, 1 mm2 (14-gauge) cord that is no longer than 1.5 m
(5 ft.). Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the circuit breaker located on the treadmill
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
d. Check the on/off switch located on the treadmill
near the power cord. The switch must be in the “on”
position.
c
Tripped
Reset
d
On
Position
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. Make sure that the on/off switch is in the “on” position (see d. above).
e. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Place the treadmill in the storage position (see HOW TO FOLD AND MOVE THE TREADMILL on page 24).
a
4
Next, remove the two indicated 3/4" Screws (4).
4
Lower the treadmill (see HOW TO LOWER THE
TREADMILL FOR USE on page 25). Remove the four
indicated 3/4" Screws (4), and remove the Hood (44).
4
44
26
4
Next, locate the Reed Switch (14) and the Magnet
(12) on the left side of the Pulley (11). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8". If necessary, loosen
the indicated Screw (29), move the Reed Switch
slightly, and then retighten the Screw. Then, reattach
the hood, and run the treadmill for a few minutes to
check for a correct speed reading.
Top
View
29
14
1/8"
11
12
PROBLEM: The walking belt slows when walked on
SOLUTION: a. If an extension cord is needed, use only a 3-conductor, 1mm2 (14-gauge) cord that is no longer
than 1.5 m (5 ft.).
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
b
3"–4"
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the hex key to turn the
left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left rear
roller bolt counterclockwise 1/2 of a turn. Be careful
not to overtighten the walking belt. Plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 3 to 4 inches off the walking platform. Be careful
to keep the walking belt centered. Then, plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
27
a
b
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, remove the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The chest pulse sensor does not function properly
SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROUBLESHOOTING on page 10.
b. If the chest pulse sensor still does not function properly, the battery
should be changed. To replace the battery, first locate the battery
cover on the back of the sensor unit. Insert a coin into the slot in the
cover, and turn the cover counterclockwise to the “open” position.
Then, remove the cover.
Next, remove the old battery from the sensor unit, and insert a new
CR 2032 battery, with the battery oriented so the writing is on
top. Make sure that the rubber gasket is in place in the sensor unit.
Then, reinsert the battery cover and turn it to the closed position.
b
Battery Cover
Battery
Cover
Battery
Rubber
Gasket
28
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
29
PART LIST—Model No. PETL61606.0
R1006A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
2
2
8
50
1
1
2
4
2
2
1
1
17
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
9
2
1
2
4
1
1
1
1
11
1
1
1
2
1
1
4
2
1
1
1
Description
Key No. Qty.
Foot Rail Cover
Foot Rail
Isolator Screw
3/4" Screw
Power Cord Adapter
Walking Platform
Belt Guide
Belt Guide Screw
Front Isolator
Platform Bolt, Front
Front Roller/Pulley
Magnet
1/2" Screw
Reed Switch Clip
Incline Rod Bushing
Lift Arm
Lift Pivot Bolt
Hood Mount
Lift Arm Spacer
Reed Switch
Idler Wheel Nut
Idler Wheel
Idler Wheel Bolt
Lift Motor Bolt, Bottom
Idler Arm Spacer
Idler Arm
Idler Arm Spring
Motor Belt
3/4" Tek Screw
Lift Pivot Bolt
Drive Motor
Motor Bolt
Electronic Bracket Nut
Electronic Bracket
Front Endcap
Controller
Incline Rod
Nut
Lift Motor
Lift Motor Bolt, Top
Motor Plate
Platform Cushion
Outlet Bracket
Hood
Hood Clip
Grommet
Walking Belt
Frame
Power Cord
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
30
1
1
4
6
1
4
2
1
1
1
1
2
2
1
6
1
1
1
2
9
1
1
4
1
1
1
1
1
8
1
4
4
4
1
1
2
2
2
1
1
10
4
2
11
2
1
1
1
1
Description
Transformer
Right Rear Foot
Rear Wheel
Rear Wheel Bolt
Right Rear Endcap
Bracket Washer
Rear Roller Adj. Bolt
Hex Key
Left Rear Foot
Left Rear Endcap
Rear Roller
Platform Nut
Platform Bolt, Rear
Console Fan
Handrail Bolt
Console Base
Console
iFIT Card Kit
Motor Bushing
Electronics Screw
Pulse Receiver Cover
Console Wire Harness
Upright Bolt
Left Upright
Right Upright
Upright Wire Harness
Left Base Cover
Right Base Cover
1/2” Tek Screw
Idler Wheel Washer
Console Crossbar Star Washer
Base Pad
1" Tek Screw
Base
Frame Ground Wire
Wheel Bolt
Wheel
Caution Decal
AV Wire
Key/Clip
Upright Star Washer
Releasable Tie
Tie Clamp
Plastic Tie
Handrail Cover
Left Upright Sleeve
Right Upright Sleeve
Filter
On/Off Switch
Key No. Qty.
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
1
1
1
1
4
1
2
1
1
1
1
1
1
1
1
4
2
2
1
Description
Handrail
Latch Assembly
Latch Warning Decal
Circuit Breaker
Console Clamp Screw
Idler Arm Bolt
Rear Roller Washer
Incline/Controller Wire
Incline Stop Bracket
Stop Bracket Spacer
Chest Pulse Strap
Console Plate
Chest Pulse Sensor
Chest Pulse Receiver
Lower Latch Bolt
Handrail Cover Fastener
Receiver Screw
Console Clamp
Upper Latch Bolt
Key No. Qty.
118
119
120
121
122
123
124
125
126
#
#
#
#
#
#
#
#
1
1
1
1
3
1
1
1
4
1
1
1
1
1
1
1
1
Description
Latch Knob
Latch Endcap
Left Pulse Grip
Right Pulse Grip
4" Ground Wire
Warning Decal, Base
Speaker Cover
Speaker
Speaker Screw
4" Green/Yellow Wire, w/Toroid
4" Green/Yellow Wire
16" Green/Yellow Wire, F/R
6" Blue Wire, 2 F
6" Blue Wire, M/F
6" White Wire, 2F
Ground Wire Nut
User’s Manual
#These parts are not illustrated
31
2
57
59
38
58
4
105
52
56
3
62
101
29
53
61
1
54
3
56
52
53
105 4
42
60
29
6
3
61
38
51
62
7
104
8
48
23
9
4
1
47
26
4
3
3
22
25
4
18
10
3
17
28
38
79
21
27
16
30
50
42
69
11
12
20
14 29
4
19
15
3
29
38
41
68
10
55
69
8
117
7
3
4
33
32
2
34
31
9
33
118
55
55
33
36
4
4
35
13
43
13
4
18
100
46
15
29
102
98
37
38
17
38
97
119
108
113
44
107
24
106
4
49
45
5
4
To identify the parts shown on this
EXPLODED DRAWING, see the
PART LIST on pages 30 and 31.
16
19
30
69
38
40
39
4
45
4
EXPLODED DRAWING—Model No. PETL61606.0
R1006A
94
13
89
13
114
124
13
13
13
78
126
78
13
4
94
109
80
110
69
63
4
111
116
4
120
125
114
103
4
4
116
99
4
112
122 115
13
66
67
4
78
4
103
4
70
78
121
78
4
80
78
13
4
71
76
4
92
29
91
86
87
65
4
4
85
4
4
4
4
93
4
64
95
38
90
82
81
4
4
90
4
4
38
64
90
73
86
90
38
72
82
81
4
4
75
90
85
83
64
96
82
81
4
64
4
46
123
90
75
4
87
90
38
72
74
77
82
81
84
69
EXPLODED DRAWING—Model No. PETL61606.0
R1006A
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4, Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Tel:
08457 089 009
Outside the UK: (44) 0113 387 7133
Fax: (44) 0113 387 7125
To help us assist you, please be prepared to give the following information:
• the MODEL NUMBER of the product (PETL61606.0)
• the NAME of the product (PROFORM 620 V treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST on pages 30 and 31 and the
EXPLODED DRAWING in the center of this manual)
Part No. 245988 R1006A
Printed in USA © 2006 ICON IP, Inc.