The company behind Avital® Auto Security Systems
is Directed Electronics.
Since its inception, Directed Electronics has had one
purpose, to provide consumers with the finest vehicle
security and car stereo products and accessories
available. The recipient of nearly 100 patents
and
KEYLESS eNTRY SYSTEM
Innovations Awards in the field of advanced electronic
technology.
Quality Directed Electronics products are sold and
serviced throughout North America and around
the world.
Call (800) 876-0800 for more information about our
products and ser­vic­es.
© 2011 Directed Electronics, All rights reserved.
Vista, CA 92081
www.avital.com
G3300L 2011-11
Directed is committed to delivering world
class quality products and services that excite and delight our customers.
O W N E R’ S
GUIDE
M
O
D
E
L
3300L
limited lifetime consumer warranty
Directed Electronics. (“Directed”) promises to the original purchaser to repair or replace
(at Directed’s election) with a comparable reconditioned model any Directed unit
(hereafter the “unit”), excluding without limitation the siren, the remote transmitters,
the associated sensors and accessories, which proves to be defective in workmanship or
material under reasonable use during the lifetime of the vehicle provided the following
conditions are met: the unit was purchased from an authorized Directed dealer, the unit
was professionally installed and serviced by an authorized Directed dealer; the unit will
be profession¬ally reinstalled in the vehicle in which it was originally installed by an
authorized Directed dealer; and the unit is returned to Directed, shipping prepaid with a
legible copy of the bill of sale or other dated proof of purchase bearing the following information: consumer’s name, telephone number and address; the authorized dealers name,
telephone number and address; complete product description, including accessories; the
year, make and model of the vehicle; vehicle license number and vehicle identification
number. All components other than the unit, including without limitation the siren, the
remote transmitters and the associated sensors and accessories, carry a one-year warranty
from the date of purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED
FOR WARRANTY REPAIR WITHOUT PROOF OF PURCHASE FROM AN
AUTHORIZED DEALER WILL BE DENIED. This warranty is non-transferable and is
automatically void if: the unit’s date code or serial number is defaced, missing or altered;
the unit has been modified or used in a manner contrary to its intended purpose; the unit
has been damaged by accident, unreasonable use, neglect, improper service, installation
or other causes not arising out of defects in materials or construction. The warranty does
not cover damage to the unit caused by installation or removal of the unit. Directed, in
its sole discretion, will determine what constitutes excessive damage and may refuse the
return of any unit with excessive damage.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES,
INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED
WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF
INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED
NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO
ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION
WITH ITS PRODUCTS. DIRECTED DISCLAIMS AND HAS ABSOLUTELY
NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING
ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED SECURITY
SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE
THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE
AGAINST VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE,
© 2011 directed electronics—all rights reser ved
i
ITS PARTS OR CONTENTS; AND HEREBY EXPRESSLY DISCLAIMS
ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION,
LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY
DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR
REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES
OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING
DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO
COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND
APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE.
THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED
SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S
PURCHASE PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE
FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO,
ANY CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGE
TO VEHICLE, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS,
COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE.
NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A
LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE
SUBJECT TO THE CONDITIONS AS DESCRIBED HEREIN. THIS WARRANTY
IS VOID IF THE UNIT HAS NOT BEEN PURCHASED FROM DIRECTED,
OR AN AUTHORIZED DIRECTED DEALER, OR IF THE UNIT HAS BEEN
DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE, ACTS OF
GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES NOT ARISING
OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.
Some states do not allow limitations on how long an implied warranty will last or the
exclusion or limitation of incidental or consequential damages. This warranty gives you
specific legal rights and you may also have other rights that vary from State to State.
This warranty is only valid for sale of product(s) within the United States of America and
in Canada. Product(s) sold outside of the United States of America or Canada are sold
“AS-IS” and shall have NO WARRANTY, express or implied.
For further details relating to warranty information of Directed products, please visit the
support section of Directed’s website at: www.directed.com
This product may be covered by a Guaranteed Protection Plan (“GPP”). See your
authorized Directed dealer for details of the plan or call Directed Customer Service at
1-800-876-0800.
920-10011-01 2011-06
ii
© 2011 directed electronics—all rights reser ved
table of contents
limited lifetime consumer warranty.......................................................................... i
remote configurations.............................................................................................. 2
LCD 2-way configuration..................................................................................... 2
standard 4-button configuration (both remotes)................................................... 4
LCD 2-way remote additional controls................................................................. 5
what is included....................................................................................................... 6
important information............................................................................................ 7
system maintenance............................................................................................... 7
your warranty........................................................................................................ 8
fcc/id notice.......................................................................................................... 8
Standard LCD 2-way icon configuration............................................................ 10
LCD 2-way remote operation................................................................................ 15
system signal paging features............................................................................... 15
using your system ................................................................................................. 16
active arming....................................................................................................... 16
passive arming..................................................................................................... 16
warn away® response description.......................................................................... 17
triggered response description.............................................................................. 18
disarming............................................................................................................ 19
high security disarm............................................................................................ 20
disarming without a remote................................................................................. 20
silent mode.......................................................................................................... 21
panic mode.......................................................................................................... 22
valet mode........................................................................................................... 22
setting the clock.................................................................................................. 23
nuisance prevention® circuitry.............................................................................. 23
diagnostics............................................................................................................. 25
arming diagnostics............................................................................................... 25
disarming diagnostics.......................................................................................... 26
system status chirps............................................................................................. 26
table of zones....................................................................................................... 27
code hopping......................................................................................................... 27
high frequency....................................................................................................... 28
rapid resume logic................................................................................................. 28
programming options ........................................................................................... 29
security & convenience expansions........................................................................ 30
installation options................................................................................................ 31
glossary of terms.................................................................................................... 32
© 2011 directed electronics—all rights reser ved
1
remote configurations
LCD 2-way configuration
4
3
2
1
31
30
5
29
AM
PM
28
27
6
7
8
9
10
11
12
26
A
25
SAVE
24
23
24
22
INHIBIT
21
13
20
14
19
15
16
17
2
18
© 2011 directed electronics—all rights reser ved
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Vehicle Interior Temperature Indicator
Numeric Display
AM/PM Indicator
Alarm Clock Mode Indicator
Timer Function Indicator
Transmit Range Indicator
Transmission Indication
Vibrate/Beep Mode Indicator
Power Saver Mode Indicator
Remote Start Timer Mode Indicator
No Function
Vehicle Page Mode Indicator
Full Trigger Shock Sensor Indicator
Hood/Trunk Open or Trigger Indicator
Parking Light Indicator
Door Open or Trigger Indicator
Arm/Lock Button
Disarm/Unlock Button
Remote Start Indicator
Hood/Trunk Open or Trigger Indicator
Remote Start Button
Valet Mode Indicator
Remote Start Safety Shutdown Indicator
Battery Level Indicator
Auxiliary Button
Temperature-Controlled Remote Start Indicator
Silent Arm/Disarm Mode Indicator
Full Trigger Alert Indicator
Arm/Disarm Indicator
Function Button
Celsius/Fahrenheit Indicator
© 2011 directed electronics—all rights reser ved
3
standard 4-button configuration (both remotes)
controls the Arm and Panic On/Off function. The arming
is controlled by pressing this button. The panic alarm is triggered
by pressing and holding this button. Press again to cancel the
panic alarm
controls the Disarm and Panic Off function. Press this
button to disarm the system or to cancel the panic alarm.
controls Silent Mode™ and Auxiliary channel 2 output.
Silent mode works by pressing this button for less than one
second before arming or disarming. And optional auxiliary function, such as trunk release, can be controlled by pressing and
holding this button for 1.5 seconds.
The auxiliary output controls __________________________.
controls the Panic function by pressing and holding this
button for 1.5 seconds.
and
pressed together control channel 3 output, and
optional auxiliary convenience or expansion function that you
have added to your system.
The auxiliary output controls __________________________.
4
© 2011 directed electronics—all rights reser ved
and
pressed together control channel 4 output, and
optional auxiliary convenience or expansion function that you
have added to your system..
The auxiliary output controls __________________________.
LCD 2-way remote additional controls
note:The controls listed below are applicable only to
the LCD 2-way remote.
The LCD backlighting will turn on when pressed for less
than one second; when held for more than five seconds the
transceiver will enter adjustment mode allowing the setting of
the clock, timer mode, and audible melody selection. For more
information, please refer to the Function Button Configurations
section of this guide.
and
Buttons
The numeric display toggles between the time of the day and the
alarm clock when these buttons are pressed simultaneously.
and
Buttons
Press these buttons simultaneously to activate the parking timer.
Each additional press will toggle through the available options
(10 min., 20 min., 30 min., 1 hour, 1.5 hours, 2 hours, and off).
© 2011 directed electronics—all rights reser ved
5
and
Buttons
When pressed simultaneously these buttons toggle between beep
notification and vibrate notification.
and
Buttons
When pressed simultaneously these buttons activate battery
saver mode, which will drop power consumption on the transceiver battery to zero when the alarm is inactive or disarmed.
what is included
6
•
Control module
•
544N transceiver/antenna
•
One 4-button remote
•
One 2-way LCD remote
•
Impact sensor on-board control module
•
High powered siren
•
Fault-proof starter interrupt relay on-board control module
•
Status LED indicator light
•
Push-button Valet button
•
Your warranty registration
© 2011 directed electronics—all rights reser ved
important information
Congratulations on the purchase of your state-of-the-art vehicle
security system. This system has been designed to provide years
of trouble-free operation. By carefully reading this guide prior
to using your system, you will maximize the use of this product
and its features.
By carefully reading this Owner’s Guide prior to using your
system, you will maximize the use of this system and its features.
You can print additional or replacement copies of this manual by
accessing our web site at www.directed.com.
system maintenance
The system requires no specific main­te­nance other than battery
replacement for the remotes.
LCD 2-Way Remote Battery Replacement
The 2-way remote is powered by a 1.5V AAA battery. The
Battery Level indicator has three level indicators that serve as a
visual indication of battery charge. When the battery reaches a
low charge level that requires replacement, the transceiver will
generate a single notification chirp, and the Battery Level indicator will flash continuously.
© 2011 directed electronics—all rights reser ved
7
To replace the battery, gently pull the battery cover release tab, then
slide the door down to expose the battery and remove the expired
battery. Place the new battery into the transceiver observing the
correct polarity. When power is returned the transceiver will light
all icons in the LCD and generate a musical tone.
4-Button Remote Battery Replacement
Your remote is pow­ered by a small, lightweight 3-volt lithium
battery (CR2032) that will last approximately one year under
normal use. When the battery begins to weaken, operating range
will be reduced and the LED on the remote will dim.
your warranty
Your system comes with a warranty. Make sure that you receive
the warranty registration card and proof of purchase from your
dealer, indicating the product was installed by an authorized
Directed dealer. Please validate it online at www.prodregister.
com/directed or complete and return the warranty registration
card.
fcc/id notice
This device complies with Part 15 of FCC rules. Operation is
subject to the following two con­di­tions: (1) This device may
not cause harmful interference, and (2) This device must accept
any in­ter­fer­ence re­ceived, including in­ter­fer­ence that may cause
undesirable op­er­a­tion.
8
© 2011 directed electronics—all rights reser ved
Directed Electronics, Inc.
544 Series
Tested to Comply
with FCC Standards
7352 Series
Directed Electronics, Inc.
474V/P/S Series
Tested to Comply
with FCC Standards
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate this device.
© 2011 directed electronics—all rights reser ved
9
Standard LCD 2-way icon configuration
Icon
The vehicle interior temperature icon has no functions
Icon
The numeric display icon will show the hours and minutes.
Icon
The AM/PM icon indicates the time before or after noon.
Icon
The alarm clock mode icon indicates that the alarm clock mode
is active.
Icon
The timer function icon flashes during timed functions including
parking timer.
Icon
The transmit range indicator icon stays visible as long as the
system is within operating range.
Icon
The remote transmission indicator icon displays when the transceiver is transmitting a signal.
Icon
The vibrate/beep mode icon appears when the transceiver is set
to vibrate mode.
10
© 2011 directed electronics—all rights reser ved
Icon
The power saver mode can be turned on or off with the transceiver. This icon displays the status.
Icon
The remote start timer mode icon has no function.
Icon
No function.
Icon
The vehicle page mode icon displays when the alarm module is
paging the transceiver.
Icon
The full trigger shock sensor icon indicates that the shock sensor
has been triggered by a hard shock.
and
Icons
The hood/trunk open or trigger icon illuminates when the hood
or trunk trigger has been activated or the hood or trunk is open,
and bypasses those zones until it is closed.
Icon
The parking light icon will flash twice when armed or disarmed.
The icon also flashes during WarnAway.
Icon
The door open or trigger icon illuminates when the door trigger
has been activated or the door is open, and bypasses that zone
until it is closed.
© 2011 directed electronics—all rights reser ved
11
Icon
The remote start icon has no function.
Icon
The Valet mode icon appears when the system is in Valet mode.
Icon
The remote start safety shut down icon has no function.
Icon
The battery level icon indicates the level of power remaining in
the battery.
Icon
The temperature-controlled remote start icon has no function.
Icon
The silent arm/disarm icon appears when the system has been
armed or disarmed in the silent mode.
Icon
The full trigger alert icon illuminates when the security system
has been triggered by a heavy impact, door trigger violation,
optional sensor violation, or a hood/trunk trigger.
Icon
The arm icon appears when the vehicle is armed and locked. The
disarm icon appears when the vehicle is disarmed and unlocked.
Icon
Celsius/Fahrenheit icon indicates the current mode of the
displayed temperature either in Celsius or Fahrenheit.
12
© 2011 directed electronics—all rights reser ved
Standard LCD 2-way button functions
Audible
FunctionButton
Iconindication
Lamp On (10 sec)
+
Power-Saver Mode*
Melody
+
Beep/Vibrate Mode
4 Vibrations/
1 Beep
Time Adjust
Mode (hour)**
for 5 Seconds
2 Beeps
Time Adjust
Mode (min)**
1 Time***
Alarm Clock Set Mode (hour)**
2 Times***
Alarm Clock Set Mode (min)**
3 Times***
Alarm Clock Music
4 Times***
or Power on Music
Selection**
5 Selections
1/2/3/4/5
5 Selections
1/2/3/4/5
Alarm Clock Adjust Mode (on/off)**
5 Times***
Timer Count Down Adjust Mode
(hour)**
6 Times***
Timer Count Down Adjust Mode
(min)**
7 Times***
8 Times***
Timer Count Down Ending Melody Selection 1**
9 Times*** RS Timer Count Down Mode (on/off)* (where applicable)
© 2011 directed electronics—all rights reser ved
13
Remote Start On 10 times***
Melody Selection 2 (where applicable)
5 Selections
1/2/3/4/5
10 Min Parking
Count Down Mode
+
1 Time
Melody
20 Min Parking
Count Down Mode
+
2 Times
Melody
30 Min Parking
Count Down Mode
+
3 Times
Melody
60 Min Parking
Count Down Mode
+
4 Times
Melody
90 Min Parking
Count Down Mode
+
5 Times
Melody
120 Min Parking
Count Down Mode
+
6 Times
Melody
Parking Count Down
Off Mode
+
7 Times
Melody
+
Alarm Clock Mode
On/Off****
Melody
Celsius/Fahrenheit Select Mode
+
+
or
Melody
* This function will operate in the disarmed state only.
** The
button will advance the selection upward. The
button will advance the selection downward or select the off setting.
down for five seconds prior to entering
*** Be sure to hold
timer clock adjust mode operation.
**** Press once to have the alarm clock on. Press twice to have the
alarm clock off.
The remote will revert to normal operation from the set mode
when 15-seconds has elapsed without a button entry.
14
14
© 2011 directed electronics—all rights reser ved
LCD 2-way remote operation
The security system operates at 434 MHz and incorporates
Directed’s proprietary A.S.K. out-board two-way transceiver.
The high frequency combined with Binary Data communication
achieves superior range with two-way communication.
system signal paging features
A page is the signal the control module sends to the transceiver
as confirmation of receipt of a command or alarm system status.
When the transceiver receives a page it will generate a page notification to the user (notifications are audible beeps or the remote
vibrates) and the LCD icons will display the current system status.
Command Page
When a command (arm/disarm, or auxiliary channel) from the
transceiver is sent and received, the system will send a command
page back to confirm receipt.
Page Recognition Mode
The transceiver will leave a zone icon illuminated when it has
received a triggered response and will wait for violation recognition. Press any button on the transceiver, the LCD information
and alarm page alerts will be cleared.
note:The transceiver buttons will not send a command to the system until the alarm page is cleared.
© 2011 directed electronics—all rights reser ved
15
using your system
important: Due to the complexity of this system,
installation of this product must only be performed
by an authorized Directed dealer.
active arming
You can arm the system by pressing
of your remote for one
second. When the system arms, you will hear a short siren sound,
or chirp, and see the parking lights flash once. If the power door
locks are con­trolled by the system, the doors will also lock. While
the sys­tem is armed, the status LED will flash approximately once
per sec­ond, indicating that the system is actively pro­tect­ing your
vehicle. If you hear a second chirp after arming and note that the
status LED is flashing in groups, see the Diagnostics Section of
this guide. This extra chirp is called Bypass No­ti­fi­ca­tion, which
indicates that a security sensor or switch has been bypassed and
the system is not monitoring that area (zone) of the vehicle.
passive arming
The system can be programmed to arm itself au­to­mat­i­cal­ly (called
pas­sive arming). If the system is programmed for passive arming,
it will automatically arm 30 seconds after the ignition is turned
off and the last protected entry has been closed. (e.g. the system
detects that you have left the vehicle by opening and closing a door.)
Whenever the system is in its 30-sec­ond passive arming count­down,
the status LED will flash twice as fast as it does when the system is
armed. If the system is programmed for Passive Arming, care must
be taken to prevent the keys from being locked in the vehicle.
16
© 2011 directed electronics—all rights reser ved
note: If any protected entry point (such as a door or a
switch-protected trunk or hood) is open, the system
will not passively arm. Ad­di­tion­al­ly, each time a protected entry is opened (triggered) during the arming
count­down, the 30-second count­down starts over.
When armed your vehicle is protected as follows:
•
•
•
•
•
Light impacts trigger the Warn Away® signal. When triggered,
the siren chirps and the parking lights flash for a few seconds.
Heavy impacts trip a Triggered Sequence. The sequence
consists of the siren sounding continuously and the parking
lights flashing for 30 seconds.
If a door is opened, the system will immediately start
chirping the siren and flashing the parking lights. Three
seconds later, the siren out­put changes to a continuous
blast. This pro­gres­sive re­sponse gives you time to disarm
the sys­tem with your remote if you inadvertently open the
door while the system is armed.
Turning on the ignition key will trip the same progressive
re­sponse as opening a door.
The starter kill prevents the vehicle’s starter from cranking.
warn away® response description
A Warn Away® Response consists of an alarm page along with the
responses described below.
•
•
Shock Sensor - Light impacts to the vehicle will flash the
vehicle lights and chirp the siren for a few seconds.
Remote Control Notification - Ten quick beeps (or vibrations).
© 2011 directed electronics—all rights reser ved
17
•
•
Remote Control LCD - The full trigger alert icon (28) will
dimly illuminate for two seconds
The transceiver will enter Page Recognition Mode and
operate alarm page alerts.
note:Icons 13 and 14 represent alarm system zone
inputs. For more information about icons and the
zones they represent refer to the Standard Remote
Configurations section.
triggered response description
A Triggered Response can be activated by any of the triggers
listed below and consists of an alarm page along with the response
described for each trigger. The Triggered Response duration is 30
seconds.
•
Sensor Trigger - Heavy impacts to the vehicle will instantly
sound the siren and flash the lights for the programmed
duration and report Zone 2.
•
Door Trigger - If a door is opened the siren will chirp for
three seconds, then the siren will sound and the lights will
flash for the programmed duration and report Zone 3. The
three seconds allow the user time to disarm the system with
a minimum of noise should a door be opened inadvertently
•
•
18
while the system is armed.
Hood Trigger - Opening the hood (if connected) will sound
the siren, flash the lights for the programmed duration, and
report Zone 1.
Trunk Trigger - Opening the trunk (if connected) will
instantly sound the siren and flash the lights for the
programmed duration and report Zone 1.
© 2011 directed electronics—all rights reser ved
•
Ignition Trigger - If the ignition is turned on the siren will
chirp for three seconds, then the siren will sound and the
lights will flash for the programmed duration and the remote
will flash.
When a Triggered Response is activated the transceiver will:
•
•
•
•
Repeat four quick beeps (or vibrate) for 15 seconds.
The full trigger alert icon (28) will turn on for 15 seconds.
The zone icons will turn on and remain on until a transceiver
button is pressed, clearing the page alert.
The transceiver will enter page recognition mode and
generate alarm page alerts.
note:Icons 13, 14, 16, and 20 represent alarm system
triggered sequence zone inputs. For more information about icons and the zones they represent refer
to the Standard Remote Configurations section.
disarming
To disarm the security system, press
. You will hear two
chirps, and the parking lights will flash twice. If the power locks
are controlled by the system, the doors will also unlock. If the
siren chirps more than twice and the LED continues to flash
after pressing the
button, the system was triggered in your
absence (Tamper Alert). Refer to the disarming discussion in the
Diagnostics Section of this guide.
© 2011 directed electronics—all rights reser ved
19
high security disarm
This security system offers High Security Disarm. High Security
Disarm is a feature that makes it possible to silence and reset
the system while it is triggering, without disarming the system.
If the system is triggered and the siren has been sounding for
longer than six seconds, pressing
on the remote will stop the
trigger and return the unit to the armed state. The system will
not disarm, but rather reset. This prevents you from disabling the
system should you wish to disarm it without visually checking
the vehicle. Pressing
after resetting the system will disarm
the system; pressing this button during the first six seconds of the
trig­gered sequence will disarm the security system immediately.
The six second timer is provided for your con­ve­nience, in case
the system is accidentally triggered.
disarming without a remote
If your remote is lost or damaged, you can manually disarm your
vehicle security system. To disarm the system without a remote,
you must have the vehicle’s ignition key and know where the
Valet button is located. Be sure to check with your installer at the
time of installation for the location of the Valet button.
20
© 2011 directed electronics—all rights reser ved
To disarm the security system,
turn the ignition to the ON position. Press the Valet button
within 15 seconds. After five
DRW-35
seconds, the sys­tem will disarm. If
the system does not disarm, you
may have waited too long; turn
the ignition off and on and try
again.
Location of Valet Button_________________________________
silent mode
To temporarily turn off the arm or disarm chirps, use Silent
Mode™. Simply press
for less than one second before
arming or disarming, and the confirmation chirp(s) will be eliminated for that one op­er­a­tion only. If you want the arm/disarm
chirps turned off permanently, your dealer can do this for you.
note: The Warn Away® response to lighter impacts is
bypassed if the system is armed using Silent Mode.
This ensures that no chirps will be emitted by the
siren in an area you want chirp-free. The system is still
fully capable of triggering by heavy impacts. Only the
Warn Away® response is bypassed.
© 2011 directed electronics—all rights reser ved
21
panic mode
If you are threatened in or near your vehicle, you can attract
attention by triggering the system with your remote. Just press
for 1.5 seconds, and you will enter Panic Mode. The siren
will sound and the parking lights will flash for the programmed
siren duration. To stop Panic Mode at any time, press
, or
,
.
The LCD 2-way remote will beep (or vibrate) continuously
when the system enters panic mode. The 2-way remote will not
generate a page notification when panic mode is exited.
valet mode
You can prevent your security system from automatically arming
and trig­ger­ing by using Valet Mode. This is very useful when
washing the ve­hi­cle or having it serviced. In Valet Mode, the
security system will not arm, even with the remote, but all convenience functions (door locks, trunk re­lease, etc.) will continue to
work nor­mal­ly. You can access Valet Mode either manually or
with the remote.
To enter or exit Valet Mode manually:
1. Turn the ignition on.
2. Turn the ignition off.
3. Press and release the Valet
DRW-35
button within 10 seconds.
The status LED will light solidly if you are en­ter­ing Valet Mode,
and it will go out if you are exiting Valet Mode.
22
© 2011 directed electronics—all rights reser ved
To enter or exit Valet Mode using the remote:
Steps 2 through 3 must be quickly and smoothly completed.
1. Open any vehicle door.
2.Press
.
3.Press
.
again.
4.Press
The status LED will light solidly if you are entering Valet Mode,
and it will go out if you are exiting Valet Mode.
setting the clock
To set the clock press and hold
for five seconds, the trans-
ceiver will chirp twice and the hour selection will start flashing.
Immediately press
to advance the hour selection or
to
reverse the hour selection. Once the correct hour is displayed
press
again and the minute selection will start flashing. Then
press
to advance the minute selection or
to reverse the
minute selection. Once the correct time is displayed simply stop
pressing any buttons for 15 seconds and the transceiver will automatically exit the clock mode.
nuisance prevention® circuitry
Your system has Directed’s Nuisance Prevention® Circuitry
(NPC®). It pre­vents annoying repetitive trigger sequences due
to faulty door pin switches or en­vi­ron­men­tal con­di­tions such as
thunder, jack­ham­mers, airport noise, etc.
© 2011 directed electronics—all rights reser ved
23
Example
If the alarm triggers three times within a 60-minute period and
each time the same sensor or switch triggers the alarm, NPC®
will interpret those triggers as false alarms. After the third trigger,
NPC® ignores, or bypasses, that sensor or switch (along with any
other sensors or switch­es sharing the same zone) for 60 minutes.
If the bypassed sensor tries to trigger the security system while
it is being by­passed, the 60-minute bypass period will start over.
This ensures that a sensor that is con­tin­u­ally being triggered will
remain bypassed.
The vehicle doors are protected by NPC® differently. If your security system is triggered by an open door for three, full 30-second
cycles (one and one half minutes), the system will bypass the
doors until the trigger ceases.
note: Arming and disarming the system does not
reset this function! The only ways to reset a bypassed
zone are for it to not trigger for 60 minutes, or to turn
on the ignition. If testing your system, it is important
to remember that the NPC® programming can cause
zones to be bypassed and appear to stop working. If
five chirps are heard when disarming, NPC® has been
engaged. If you wish to clear the NPC® memory, turn
24
© 2011 directed electronics—all rights reser ved
diagnostics
The microprocessor at the heart of your system is constantly
mon­i­tor­ing all of the switches and sensors connected to it. It is
designed to detect any faulty switches and sensors and prevents
them from disabling the entire system. The microprocessor will
also record and report any triggers that occurred during your
absence. Refer to the System Status Chirps and Table of Zones
sections of this guide for diagnostic information.
arming diagnostics
If the security system is armed at the same time that an input is
active (such as a door opening or sensor triggering), you will hear
one siren chirp to indicate arming and a second siren chirp to
indicate Bypass Notification. A Bypass Notification chirp means
that the security system ignores the input that was active when the
system was armed, until that input ceases. Three seconds after that
input ceases, the security system will resume normal monitoring.
For example, if your vehicle has an interior light exit delay and you
arm your security system before the interior light turns off, you
may hear a second Bypass Notification chirp. Three seconds after
the light turns off, however, the security system resumes normal
monitoring.
note: Bypass Notification does not occur when the
system is in Silent Mode or if the notification chirps
have been programmed off by the installer.
© 2011 directed electronics—all rights reser ved
25
disarming diagnostics
Extra chirps that are heard when disarming the system are the
Tamper Alert. If four chirps are heard when disarming the
system, then the security system was triggered in your absence.
If five chirps are heard when disarming the system, a zone was
triggered so many times that the Nuisance Protection® Circuitry
has bypassed that zone. In either case, the status LED will indicate which zone was involved (see Table of Zones section). The
security system will retain this in­for­ma­tion in its memory and
chirp four or five times each time it is dis­armed, until the next
time that the ignition is turned on.
system status chirps
The siren will chirp when arming/disarming the system. The
pattern of chirps will audibly report the system’s status as
described below.
26
Action Arm
Number of Chirps
Description
1
System armed
Arm
1 (3-second delay), 1
System armed with
Bypass Notification
System disarmed
Disarm
2
Disarm
4
System disarmed with
Tamper Alert
Disarm
5
System disarmed NPC®
active
© 2011 directed electronics—all rights reser ved
table of zones
A zone is represented by the number of LED flashes used by
the system to identify a particular type of input. Standard input
assignments are listed in the following table, along with spaces to
write in any optional sensors or switches that have been installed.
ZONE
(Number of
LED Flashes) DESCRIPTION
DEALER-INSTALLED
OPTIONS
1
Instant trigger for optional
hood or trunk pin
2
Instant trigger - a heavier impact
detected by the on-board shock sensor
3
Door switch trigger
5
Ignition trigger
code hopping
The receiver and remotes use a math­e­mat­i­cal formula called an
algorithm to change their code each time the remote is used.
This tech­nol­o­gy has been de­vel­oped to increase the security of
the unit. The control unit knows what the next codes should be.
This helps to keep the remote “in sync” with the control unit
even if you use the remote control out of range of the vehicle.
How­ev­er, if the remote has been pressed many times out of
range of the vehicle, or the battery has been removed, it may fall
out of sync with the control unit and fail to operate the system.
To re-sync the remote simply press
© 2011 directed electronics—all rights reser ved
several times within
27
range of the vehicle. The alarm will automatically re-sync and
respond to the remote normally.
high frequency
Your system transmits and receives at 434 MHz. This provides a
cleaner spec­trum with less interference and a more stable signal.
Enjoy a phe­nom­en
­ al increase in range, even in areas with high
radio in­ter­fer­ence.
rapid resume logic
This Directed system will store its current state to non-volatile
memory. If power is lost and then reconnected the system will
recall the stored state from memory. This means if the unit is in
Valet Mode and the battery is dis­con­nect­ed for any reason, such
as servicing the car, when the battery is re­con­nect­ed the unit will
still be in Valet Mode. This applies to all states of the system
including arm, disarm, and Valet Mode.
28
© 2011 directed electronics—all rights reser ved
programming options
Programming options control your system’s normal, operational
set-up. Most options do not require additional parts, but some
may require installation labor.
The following is a list of the programmable options, with the
factory settings in Bold.
•
Active arming (from remote only) or passive arming
(automatic arming 30 seconds after the last door has been
closed).
•
Arming/disarming siren chirps on or off.
•
The ignition controlled door lock feature on or off: When
this feature is programmed on, the doors will lock three
seconds after the ignition is turned on, and unlock when the
ignition is turned off.
•
Passive door locking (with passive arming) or active door
locking (only when arming with the remote). Passive
locking allows the vehicle’s doors to lock when the security system passively arms (after the 30-second countdown). This feature only works if passive arming has been
programmed.
•
Siren tones and chirp volume. The output of the Revenger™
Soft Chirp™ siren consists of six different tones in sequence.
Any of these tones can be eliminated by a dealer, resulting in
a unique, easily identifiable siren sound. The chirps can be
either full volume or 6 decibels quieter than the full alarm
blast.
© 2011 directed electronics—all rights reser ved
29
security & convenience expansions
Listed below are some of the many expansion options avail­able.
Please consult your dealer for a complete explanation of all the
options avail­able to you.
Audio Sensor: Metal on glass, glass cracking, and breaking
glass produce dis­tinc­tive acoustic signatures. The 506T audio
sen­sor uses a mi­cro­phone to pick up sounds, then analyzes them
with pro­pri­etary acoustic software to determine if the glass has
been struck.
Backup Battery: The 520T keeps the system armed, triggers the
alarm and keeps the starter interrupt active if main battery is
dis­con­nect­ed.
Field Disturbance Sensor: An invisible dome of coverage is es­tab­
lished by installing the 508D “radar” sensor. Your system can
react to any intrusions into this field with the full triggered
sequence.
Power Locks: This system offers lock outputs that can control
some man­u­fac­tur­ers’ power door lock systems. For other
systems, ad­di­tion­al parts may be required.
Power Trunk Release: The accessory output of the system can
op­er­ate a factory power release for the ve­hi­cle’s trunk or hatch.
Although the on-board relay can control most power trunk
re­leas­es, sometimes an optional relay is required. If the factory
release is not power-activated, Directed®’s 522T trunk release
solenoid can often be added.
30
© 2011 directed electronics—all rights reser ved
Power Window Control: Automatic power window control is
pro­vid­ed with the 529T and 530T systems. These can operate
power win­dows, and can roll them up automatically when the
system is armed, roll them down, or both up and down.
installation options
Installation options may require additional parts or labor. Please
consult your dealer.
Progressive Unlocking: With electric power door locks, the
system can be configured so that when disarmed, only the driver’s door unlocks. A second press of the disarm button within 15
seconds of disarming unlocks the remaining doors.
Horn Honk: If connected, the horn will sound if the alarm is
either triggered by an intrusion or activated by Panic Mode. (In
most vehicles, this feature requires that an additional relay be
installed.)
Interior Light Illumination: The interior domelight can be
configured to illuminate for 30 seconds after the alarm is
disarmed. If the system is rearmed during that 30-second period,
the interior light illumination will terminate until the alarm is
disarmed once again.
© 2011 directed electronics—all rights reser ved
31
glossary of terms
Control Unit: The “brain” of your system. Usually hidden under-
neath the dash area of the vehicle. The control unit houses the
microprocessor which monitors your vehicle and controls all
system functions.
Fault-Proof Starter Interrupt: An automatic switch controlled by
your system that prevents the vehicle’s starter from cranking
whenever the system is armed. The vehicle is never prevented
from cranking when the system is disarmed, in Valet mode, or
if the starter interrupt switch itself fails. Your system has featureready circuitry for the starter interrupt, however installation may
require additional labor.
Input: A physical connection to the system. An input can be
provided by a sensor, pinswitch or by existing systems in the
vehicle, such as ignition or courtesy lights.
LCD 2-Way Remote: A hand-held, transceiver which operates and
monitors the various functions of your system.
LED: A red light mounted at a discretionary location inside the
vehicle. It is used to indicate the status of your system.
Shock Sensor: This system has a dual zone shock sensor. This
sensor is mounted in the vehicle and designed to pick up impacts
to the vehicle or glass.
32
© 2011 directed electronics—all rights reser ved
Trigger or Triggered Sequence: This is what happens when the
alarm “goes off” or “trips.” The triggered sequence of your
system consists of the siren sounding and parking lights flashing
for the programmed duration.
Valet Button: A small push-button switch mounted at a discre-
tionary location inside the vehicle. It is used to override the
starter interrupt when a remote is lost or damaged, or to enter
or exit Valet Mode.
Warning Zone Response: Lighter impacts to the vehicle will
generate the Warning Zone response. It consists of several
seconds of siren chirps and parking light flashes.
Zone: A zone is a separate input that the alarm can recognize as
unique. Each input to the system is connected to a particular
zone. Often two or more inputs may share the same zone.
© 2011 directed electronics—all rights reser ved
33
34
“
QUICK REFERENCE GUIDE
Arming
n To arm, press
. When the system arms, you will hear a short chirp, and
the parking lights will flash once.
Cut along dotted line and fold for a quick and easy ref­er­ence to keep in your purse or wallet.
Disarming
n To disarm, press
flash twice.
. You will hear two chirps, and the parking lights will
High security disarm
n For high security disarm, press
on your remote and the siren will stop
sounding. To completely disarm the security system, press again and the
system will chirp 4 or 5 times (re­porting­the trigger).
Disarming without a remote
n Turn on the ignition. Press the Valet button within 15 seconds. The
system should now disarm. If it does not, you may have waited too long,
so turn the ignition off and on and try again.
Silent Mode™
nPressing
briefly before arming or disarming will eliminate the con­fir­ma­
tion chirp(s) for that one op­er­a­tion only.
Panic Mode
nPress
for 2 seconds, and you will enter Panic Mode. The siren will sound
and the parking lights will flash for 30 seconds. To stop Panic Mode at any
on the remote again.
time, press
“
Location of Valet switch_________________________________
© 2011 directed electronics—all rights reser ved
35