Radio Shack ET-3504 Owner`s manual

ET-3504 900 MHz Cordless
Phone
Please read before using this equipment.
Owner’s Manual
with Caller ID/Call Waiting
ˆ Read This Before Installation
Your phone is ETL listed to UL standards
and meets all applicable FCC standards.
WARNING: To reduce the risk of fire or shock
hazard, do not expose this product to rain or
moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
!
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
This symbol is intended to alert
you to the presence of uninsulated
dangerous voltage within the
product’s enclosure that might be
of sufficient magnitude to constitute a risk of electric shock. Do not
open the product’s case.
!
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accompanying this product.
Each device that you connect to the phone
line draws power from the phone line. We refer to this power draw as the device’s ringer
equivalence number, or REN. The REN is on
the bottom of the base.
If you are using more than one phone or other device on the line, add up all the RENs. If
the total is more than five (three in rural areas), your phone might not ring. If ringer operation is impaired, remove a device from the
line.
FCC STATEMENT
This telephone complies with Part 68 of FCC
Rules. You must, upon request, provide the
FCC registration number and the REN to
your phone company. These numbers are on
the bottom of the base.
Note: You must not connect your phone to
any of the following:
• coin-operated systems
• party-line systems
• most electronic key phone systems
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone causes
problems on the phone line, the phone company can temporarily discontinue your service. If this happens, the phone company
attempts to notify you in advance. If advance
notice is not practical, the phone company
notifies you as soon as possible and advises
you of your right to file a complaint with the
FCC.
Also, the phone company can make changes
to its lines, equipment, operations, or procedures that could affect the operation of this
telephone. The telephone company notifies
you of these changes in advances, so you
can take the necessary steps to prevent interruption of your telephone service.
This equipment complies with the limits for a
Class B digital device as specified in Part 15
of FCC Rules. These limits provide reasonable protection against radio and TV interference in a residential area. However, your
© 2001 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
2
Read This Before Installation
equipment might cause TV or radio interference even when it is operating properly. To
eliminate interference, you can try one or
more of the following corrective measures:
• Reorient or
antenna.
relocate
the
receiving
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical circuits
for the equipment and the radio or TV.
Consult your local RadioShack store if
the problem still exists.
LIGHTNING
You telephone has built-in lightning protection to reduce the risk of damage from surges in telephone line and power line current.
This lightning protection meets or exceeds
FCC requirements. However, lightning striking the telephone or power lines can damage
your telephone.
Lightning damage is not common. Nevertheless, if you live in an area that has severe
electrical storms, we suggest that you unplug
your phone when storms approach to reduce
the possibility of damage.
IMPORTANT CALLER ID
INFORMATION
To use the phone’s Caller ID and Call Waiting features, you must be in an area where
Caller ID and Call Waiting services are available and you must subscribe to the services.
Where Caller ID is offered, one or more of
the following options are generally available:
For the phone’s Caller ID memory dial feature to operate, you must receive the caller’s
number.
Important: Cordless phones generally require AC power to operate. You should also
have a corded phone that does not require
AC power to operate so you can still make
and receive calls if there is an AC power failure.
Your telephone operates on standard radio
frequencies as allocated by the FCC. Even
though the access protection code prevents
unauthorized use of your phone line, it is
possible for other radio units operating on
similar frequencies within a certain area to
unintentionally intercept your conversations
or cause interference. This lack of privacy
can occur with any cordless phone.
CARE
Keep the phone dry; if it gets wet, wipe it dry
immediately. Use and store the phone only in
normal temperature environments. Handle
the phone carefully; do not drop it. Keep the
phone away from dust and dirt, and wipe it
with a damp cloth occasionally to keep it
looking new.
Modifying or tampering with the phone’s internal components can cause a malfunction
and might invalidate its warranty and void
your FCC authorization to operate it. If your
phone is not performing as it should, take it
to your local RadioShack store for assistance. If the trouble is affecting the telephone
lines, the phone company can ask you to disconnect your phone until you have resolved
the problem.
• caller’s number only
• caller’s name only
• caller’s name and number
Read This Before Installation
3
ˆ Contents
Features .................................................................................................................................. 5
Installation ..............................................................................................................................
Mounting the Phone .............................................................................................................
On a Desk ........................................................................................................................
On a Wall Plate ................................................................................................................
Directly On a Wall ............................................................................................................
Connecting, Charging, and Replacing the Battery Pack ......................................................
6
6
6
6
7
7
Operation ................................................................................................................................ 9
A Quick Look at the Handset ............................................................................................... 9
Storing Your Area Code ..................................................................................................... 10
Using a Headset ................................................................................................................ 10
Using Page/Find ................................................................................................................ 10
Memory Dialing .................................................................................................................. 10
Storing a Number in Memory ......................................................................................... 10
Entering a Pause in a Memory Number ........................................................................ 11
Dialing a Stored Number ............................................................................................... 11
Reviewing Stored Numbers ........................................................................................... 11
Deleting a Stored Number ............................................................................................. 11
Chain Dialing Service Numbers ..................................................................................... 12
Testing Stored Emergency Numbers ............................................................................. 12
Message Waiting ........................................................................................................... 12
Caller ID Operation ............................................................................................................ 12
Call Waiting .................................................................................................................... 12
Caller ID Messages ....................................................................................................... 12
Reviewing Caller ID Records ......................................................................................... 13
Dialing a Number from a Caller ID Record .................................................................... 13
Storing a Caller ID Record in Memory ........................................................................... 14
Deleting Caller ID Records ............................................................................................ 14
Troubleshooting ....................................................................................................................15
4
Contents
ˆ Features
Your RadioShack 900 MHz Cordless Phone
offers the latest advances in cordless phone
technology. It combines a cordless phone
and a Caller ID unit in one system. It saves
up to 40 Caller ID records that you can review and call back. Its headset jack lets you
connect an optional headset (available at
your local RadioShack store) for hands-free
convenience. The base’s space-saving design makes it perfect for areas where space
is limited.
Its other features include:
3-Line LCD Display — lets you view a caller’s name and number on one screen.
your phone line while the handset is off the
base.
10-Channel Auto Scan — automatically selects a clear channel when you make or answer a call.
Volume Control — lets you control the
volume of the sound you hear through the
handset.
Page — lets you send a paging signal from
the base to the handset to help locate a misplaced handset or page someone at the
handset.
10-Memory Speed Dial — stores up to 10
frequently called phone numbers for easy dialing.
Call Waiting ID — displays Caller ID information about an incoming call when you are
on the phone (if you subscribe to this service
from your local phone company).
Message Waiting Indicator — lets you see
at a glance that you have messages.
Review Scrolling — lets you scroll through
all records in Caller ID memory and stored
number memory.
Callback — lets you dial the phone number
in a Caller ID record.
Caller ID Memory — stores up to 40 Caller
ID records, including the time of the call.
Ample Talk and Standby Time — when fully charged (about 12 hours), the supplied
battery pack provides about 7 hours of talk
time or 7 days of standby time.
Security Access-Protection Code — prevents other cordless phone users from using
Features
5
ˆ Installation
MOUNTING THE PHONE
You can place the phone on a desk or table,
or mount it on a standard wall plate or directly on a wall.
2. Rotate the bracket 180°, then insert the
bracket’s tabs into the upper tab slots
and snap into place.
Select a location that is:
• near an easily accessible AC outlet
3. Plug the modular cord’s other end into a
modular phone line jack.
• near a telephone line jack
• out of the way of normal activities
• away from electrical machinery, electrical appliances, metal walls, filing cabinets, wireless intercoms, security
alarms, and room monitors
The base’s location affects the phone’s
range. If you have a choice of several locations, try each to see which provides the best
performance.
Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can
update the wiring yourself using jacks and
adapters (available at your local RadioShack
store), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with
Part 68 of FCC Rules.
Note: The USOC number of the jack to be
installed is RJ11C (or RJ11W for a wall plate
jack).
On a Desk
Follow these steps to use the supplied bracket (pre-installed into the lower tab slots) as a
stand when mounting the base on a desk or
table.
6
1. Press down on the tabs on the top of the
bracket and lift the bracket from the clip
slots. Remove the bracket completely
from the lower tab slots.
4. Route the adapter and phone cords
through the strain relief slot on the
bracket if necessary.
5. Plug the adapter into a standard AC outlet.
6. Lift the base’s antenna to a vertical position.
On a Wall Plate
1. Route the adapter and phone cords
through the strain relief grooves on the
bottom of the bracket if necessary.
2. Plug the modular cord into the wall plate
jack, then align the bracket’s keyhole
slots with the wall plate studs and slide
the base downward to secure it.
3. Plug the adapter into a standard AC outlet.
4. Press up on the handset holder and
slide it out of place. Turn it upside down
so its tabbed edge faces up, then slide it
back down into its slot.
5. Lift the base’s antenna to a vertical position.
Installation
Directly On a Wall
For this mounting method, you need two
screws (not supplied) with heads that fit into
the keyhole slots on the bottom of the base.
1. Drill two holes 315/16 inches (100 mm)
apart. Then thread a screw into each
hole, letting the heads extend about 3/16
inch (4 mm) from the wall.
2. Route the modular and adapter cords
through the grooves on the bottom of
the bracket if necessary.
3. Align the keyhole slots with the mounting screws and slide the base downward
to secure it.
4. Plug the modular cord into a modular
phone line jack.
5. Plug the adapter into a standard AC outlet.
6. Press up on the handset holder and
slide it out of place. Turn it upside down
so its tabbed edge faces up, then slide it
back down into its slot.
7. Lift the base’s antenna to a vertical position.
CONNECTING, CHARGING,
AND REPLACING THE
BATTERY PACK
The phone comes with a rechargeable
nickel-cadmium battery pack. You must connect the battery pack and charge it for at
least 12 hours before you use the phone for
the first time.
1. Slide off the battery compartment cover.
2. Unfasten the retainer strap and lift the
battery pack out of the compartment.
3. Plug the battery pack’s connector into
the socket in the compartment (the connector fits only one way), then replace
the battery pack and fasten the retainer
strap.
4. Replace the cover.
To charge the battery pack, place the handset either faceup or facedown on the base.
The CHARGE/IN USE/MESSAGE indicator
lights.
Notes:
• Recharge the battery pack if the handset
beeps and LOW BATTERY appears, or
if LOW BATTERY appears when the
phone is not in use.
• If the phone does not work immediately
after charging or recharging the battery
pack, return the keypad to the base for
about 5 seconds to reset the security
access-protection code.
• About once a month, fully discharge the
battery pack by keeping the phone off
the base until the low battery warning
tone sounds. Otherwise, the battery
pack loses its ability to fully recharge.
• When the handset is on the base, the
CHARGE/IN USE/MESSAGE indicator
lights even when the battery pack is not
connected. If your phone does not work,
be sure the battery pack is properly connected.
• If the CHARGE/IN USE/MESSAGE indicator does not light when you place the
handset on the base, be sure the battery
pack and AC adapter are correctly and
securely connected.
• Check the charging contacts on the
handset and base. If the contacts are
dirty or tarnished, clean them with a
pencil eraser.
Installation
7
• If the battery pack becomes completely
discharged or the base loses power
while the handset is away from it, place
the handset on the base for about 5 seconds to reset the security access protection code. If the handset loses power,
leave it on the base to charge the battery pack.
• If you are not going to use your phone
for an extended period, disconnect its
battery pack. This helps increase the
battery pack’s life.
The supplied battery pack should last about
a year. If the battery pack does not hold a
charge for more than 2 hours after overnight
charge, replace it with a new 3.6-volt, 600
mAh battery pack with a connector that fits
the socket in the battery compartment. You
can order a replacement battery pack
through your local RadioShack store. Install
the new battery pack, place the handset on
the base, and charge the battery for 12 hours
before using it.
If you have trouble replacing the battery
pack, take the phone to your local
RadioShack store for assistance.
Important: The EPA certified
RBRC® Battery Recycling Seal
on the nickel-cadmium (Ni-Cd)
battery indicates RadioShack
is voluntarily participating in an
industry program to collect and recycle these
batteries at the end of their useful life, when
taken out of service in the United States or
Canada. The RBRC program provides a convenient alternative to placing used Ni-Cd batteries into the trash or the municipal waste
stream, which may be illegal in your area.
Please call 1-800-THE-SHACK (1-800-8437422) for information on Ni-Cd battery recycling and disposal bans/restrictions in your
area. RadioShack’s involvement in this program is part of the company’s commitment to
preserving our environment and conserving
our natural resources.
Note: To avoid losing numbers stored in
memory, you must install and begin charging
the new battery pack within 2 minutes of removing the old one.
Warning: Dispose of the old battery pack
promptly and properly. Do not burn or bury it.
Cautions:
• You must use a replacement battery
pack of the same size and type.
• Do not dispose of the battery pack in a
fire because it might explode.
• Do not open or mutilate the battery
pack.
• Be careful not to short the battery pack
by touching the connector’s pins with
conducting materials, such as rings,
bracelets, and keys. The battery pack or
conductor might overheat and burn.
8
Installation
ˆ Operation
A QUICK LOOK AT THE HANDSET
TALK — To make a call, lift the handset from the base, then press TALK.
You hear a dial tone and the CHARGE/
IN USE/MESSAGE indicator lights.
Dial the number you want to call.
To answer a call, lift the handset from
the base, then press TALK. The
CHARGE/IN USE/MESSAGE indicator
lights.
To end a call, place the handset on the
base or press TALK.
This phone has a call duration timer
that starts counting from 00:00 when
you press TALK to make or receive a
call. The time stops counting when
you press TALK again to end the call.
The call duration display remains for
12 seconds after you end the call.
Notes:
When you press a button, a single
tone indicates that the phone has accepted the command. Three tones indicate that you pressed a button in
error or there is severe interference.
If interference is severe, the handset
might lose communication with the
base and the call might disconnect. If
this happens, return the handset to
the base for about 5 seconds to reset
the security access-protection code.
8/9
9—
To adVOL/CID
just the handset’s volume level,
repeatedly press VOL/CID 8
or 9 during a call. The volume
level remains set after you hang
up. There are four volume levels.
Note: The handset sounds 3
beeps when you reach the lowest or highest listening level.
—
proFLASH/DELETE
vides the electronic equivalent of a switchhook signal
for special phone services
such as Call Waiting.
For example, if you have
Call Waiting, press
FLASH/DELETE to answer an incoming call without disconnecting the
current call. Press FLASH/
DELETE again to return to
the first call.
Note: If you do not have any
special phone services,
pressing FLASH/DELETE
might disconnect your current call.
CH — Every time you press
TALK, the phone automatically
selects a clear channel it uses for
communication between the
handset and the base. If you hear
interference during a call, repeatedly press CH to change the
channel until you get a clear one.
REDIAL — To quickly redial the last number dialed, press TALK then REDIAL/CALLBACK.
To redial a busy number, press REDIAL/
CALLBACK without hanging up the phone.
<B7I> appears and a dial tone sounds for about
2 seconds, then the number automatically redials.
Notes:
The redial memory holds up to 32 digits, so you
can redial long-distance as well as local numbers.
RINGER — To have the phone ring when a call comes
in, set RINGER to ON. To turn the ringer off, set RINGER to OFF.
With RINGER set to OFF, the phone does not ring, but
you can still make outgoing calls. If you hear an extension telephone ring, you can answer the incoming call
on this phone. The CHARGE/IN USE/MESSAGE indicator flashes and the display backlight lights until you answer the call.
Operation
9
STORING YOUR AREA
CODE
MEMORY DIALING
To dial a number from a Caller ID record
(see “Dialing a Number from a Caller ID
Record” on Page 13), you must first store
your local area code in the phone’s memory.
Then, when you dial from a Caller ID record,
the system skips the area code if it matches
the one you stored. Follow these steps to
store your area code.
You can store up to 10 numbers of 24 digits
each in the phone’s memory.
Notes:
• To keep your accounts secure, we recommend you do not store your personal
access code for services such as bankby-phone in a memory location.
• When storing numbers for special services (such as alternate long-distance or
bank-by-phone), store the service’s
main phone number in one memory
location and numbers for additional
information in other locations.
1. Make sure the CHARGE/IN USE/MESSAGE indicator is not lit.
2. Hold down FUNC for 2 seconds. AREA
CODE= --- appears.
3. Enter your three-digit area code. The
handset sounds two long beeps. The
area code is stored.
Storing a Number in Memory
1. Press MEM on the handset.
To replace a stored area code, store a new
one in its place.
2. Press the memory location number (1–
0) where you want to store a number.
USING A HEADSET
You can make or answer calls with handsfree convenience using an optional headset
with a 3/32-inch (2.5 mm) plug. Contact your
local RadioShack store for a suitable headset. To connect the headset, insert the headset plug into the jack on the top of the
headset.
Note: To enter a number into the 10th
memory location, press 0.
3. Press MEM again. ;DJ;HýD7C; appears.
4. If you have name-only or name-andnumber Caller ID, enter the name (up to
15 characters) using this table:
# of
Presses
USING PAGE/FIND
To send a page to the handset to locate it
when it is away from the base and not in use,
press PAGE on the base. F7=?D= appears and
the handset rings for about 15 seconds.
1
2
–
2
3
4
5
6
7
8
9
A
D
G
J
M P
T
W
B
E
H
K
N
U
X
Q
3
*
C
F
I
L
O
R
V
Y
4
!
(
)
$
‘
;
S
?
Z
To locate the handset, hold down PAGE. The
handset rings for about 1 minute. Press any
key on the handset or PAGE on the base to
silence it sooner.
10
1
Operation
Notes:
• If you make a mistake, press FLASH/
DELETE to delete a letter.
• Press 1 to enter a space between
names.
• If you are using two consecutive letters that reside in the same number
key, press FUNC between the letters.
For example, for “Tammy Smith,”
enter 8 2 6 FUNC 6 999 1 7777 6 444 8
44.
5. Press MEM again. ;DJ;Hý J;Bý DKC8;H
appears.
6. Dial the desired number (up to 24 digits).
7. Press MEM again to store the number.
The handset sounds two long beeps.
Note: If you hear three short beeps, you
did not store the number successfully.
Start again from Step 1.
8. Write down the stored name and number on the memory index sticker provided.
Notes:
second dial tone before you can dial an outside number. You can store the access code
with the phone number. However, if you do,
you should also store a pause after the access code to allow the outside line time to
connect. After entering the access code,
press REDIAL to enter a 2-second pause.
Dialing a Stored Number
Press TALK. When you hear the dial tone,
press MEM then the memory location number
(1–0). The memory location number appears
and the phone dials the number.
To pre-dial a stored number, press MEM then
VOL/CID 8 or 9 to find the desired number,
then press REDIAL/CALL BACK.
Reviewing Stored Numbers
Press MEM. Enter the desired memory location number (1, 2, 3, and so on), or press
VOL/CID 8 or 9 to scroll through the memory locations.
Deleting a Stored Number
• If the low battery warning tone
sounds, recharge or replace the battery within two minutes, or the numbers stored in memory will be lost.
• If you receive a call while you are
storing a number in memory, press
TALK to answer the call. After the
call, begin at Step 1 to store a number.
• To change a number stored in memory, simply store a new number in that
memory location.
1. Make sure the CHARGE/IN USE/MESSAGE indicator is not lit.
2. Press MEM then enter the memory location number of the number to be
deleted, press VOL/CID 8 or 9 to
select the memory location.
3. Press FLASH/DELETE. ;H7I;ý C;CE5
appears.
4. Press FLASH/DELETE again to clear the
memory. Two long beeps sound to confirm the number is deleted.
Entering a Pause in a Memory
Number
Or, press any other button to cancel the
deletion. Three short beeps sound.
In some telephone systems, you must dial an
access code (9, for example) and wait for a
Operation
11
Chain Dialing Service Numbers
er’s name, if available (See “Caller ID Messages”).
For quick recall of numbers for special services (such as alternate long distance or
bank by phone), store each group of numbers in its own memory location.
When calling special services, dial the service’s main number first. Then, at the appropriate place in the call, press MEM, then the
number for the location where the additional
numbers are stored.
Testing Stored Emergency
Numbers
If you store an emergency service’s number
(police department, fire department, ambulance) and you want to test the stored number, make the test call during the late
evening or early morning to avoid peak demand periods. Remain on the line to explain
the reason for your call.
Note: The CHARGE/IN USE/MESSAGE indicator flashes during an incoming call, and
NEW CALL # appears. The latest Caller ID
record appears when the phone rings, then
NEW CALLS # or REPT remains on the display after the last incoming call.
Call Waiting
If you subscribe to Call Waiting and a call
comes in while you are on the phone, you
hear a tone that indicates you have another
call. The system displays the Caller ID/Call
Waiting information for about 10 seconds,
then stores the information.
To answer the incoming call, press FLASH/
DELETE. To resume the previous phone conservation, press FLASH/DELETE again.
Caller ID Messages
Message Waiting
If you subscribe to a message waiting service with your local telephone company, the
CHARGE/IN USE/MESSAGE indicator flashes and C;II7=;ý M7?J?D= appears for about
six seconds when you have a new message
waiting. The indicator continues to flash until
you listen to all of your messages.
Display
NEW CALL #
Indicates the number
of new calls. Note:
NEW does not appear
after you review the
display information.
NEW= XX
TOTAL= XX
Indicates the total
numbers of all calls
and new calls. XX is
the number of calls.
PRIVATE
The caller chose not
to send Caller ID
information.
OUT OF AREA
The caller is not
within a Caller ID service area.
REPT
You have received a
call from the same
phone number more
than once.
CALLER ID OPERATION
If you subscribe to Caller ID service from
your phone company, the system automatically displays information about calls you receive and stores the information in Caller ID
memory. The system can store up to 40
number records (the most recent is 40), then
replaces the oldest call with each new one.
The first line of the Caller ID record shows
the calling time, date and the number of
calls. The second line shows the caller’s
phone number. The third line shows the call12
Description
Operation
Display
• caller’s name (if available)
Description
Follow these steps to review Caller ID
records.
NO DATA
Caller’s information
was distorted before
reaching the system.
MSG WAITING OFF
All new messages
have been reviewed.
LONG DISTANCE
Your phone company
sends information
indicating that the
incoming call is long
distance.
2. Repeatedly press VOL/CID 8 to review
from CALL # 01 forward, or VOL/CID 9
to review records from the most recent
call back.
CALL FORWARD
The call was forwarded from a number set to forward all
calls. The display toggles between the
caller’s name and
CALL FORWARD.
3. To review the last number dialed, press
REDIAL/CALLBACK.
CALL FWD BUSY
END OF LIST
Notes:
• The handset display shows the first 15
characters of the caller’s name and the
last 15 digits of the phone number.
The call was forwarded from a number set to forward a
call if the line is busy.
The display toggles
between the caller’s
name and CALL
FWD BUSY.
You have reached the
last call.
MESSAGE WAITING A message is waiting.
(You must subscribe
to your phone company’s message waiting service.)
ERROR
1. Make sure the CHARGE/IN USE/MESSAGE indicator is not lit.
• Empty Caller ID memory locations do
not appear.
• When the list is full, the oldest caller’s
information is replaced by the newest
one.
Dialing a Number from a Caller ID
Record
Note: The system cannot dial a number if the
Caller ID record consists of a name only.
1. Make sure the CHARGE/IN USE/MESSAGE indicator is not lit.
The Caller ID information was garbled.
2. Press VOL/CID 8 or
desired number.
Reviewing Caller ID Records
Each time you receive a call, your system
stores a Caller ID record that you can review
later, even during a call. Each record includes:
• call number
9 to find the
3. Press FUNC to dial the long distance
prefix (1) plus the area code and local
number. For example, if the area code is
604 and the local number is 555-1212,
the phone dials 1-604-555-1212.
Press FUNC twice to dial the local phone
number (555-1212).
• time and date of the call
• caller’s telephone number (if available)
Operation
13
Press FUNC three times to dial the long
distance prefix and local number (1-5551212).
desired number, then press FLASH/
DELETE. ERASE CALL ID? appears.
Press FUNC four times to dial the area
code and local number (604-555-1212).
DELETE for 3 seconds.
To delete all records, hold down FLASH/
4. Press REDIAL/CALL BACK. The system
dials the caller’s phone number.
Storing a Caller ID Record in
Memory
3. Press FLASH/DELETE again to confirm
the deletion. The handset sounds two
long beeps and the selected number is
deleted.
1. Make sure the CHARGE/IN USE/MESSAGE indicator is not lit.
2. Press CID/VOL 8 or 9 to find the
desired caller ID record. The caller ID
memory shows the phone number with
area code.
3. Press FUNC to store the number as
specified in Step 3 of “Dialing a Number
from a Caller ID Record.”
4. Press MEM once. SELECT MEMO 0-9?
appears.
5. Enter the memory location number. The
handset sounds two long beeps.
Notes:
• If the handset sounds three short beeps,
the caller’s number is not stored. Start
again from Step 1.
• You cannot store a Caller ID record without the caller’s number or name in the
phone’s memory.
Deleting Caller ID Records
1. Make sure the CHARGE/IN USE/MESSAGE indicator is not lit.
2. To delete a single record, repeatedly
press VOL/CID 8 or 9 to find the
14
ERASE ALL?
appears.
Operation
Or, press any button other than FLASH/
DELETE to cancel the deletion. The
handset sound three short beeps.
ˆ Troubleshooting
We do not expect you have any problems with your telephone, but if you do, the following suggestions might help.
Problem
The handset does not work.
Suggestion
Move the handset closer to the base.
Raise the base’s antenna to a vertical position.
Ensure the phone’s modular cord and the AC adapter are correctly and securely connected.
Recharge the handset’s battery pack.
Return the handset to the base for about 5 seconds to reset the
security access-protection code.
Call is noisy.
Keep the handset and the base away from interference sources
such as computers, remote control toys, wireless alarm systems,
wireless intercoms and room monitors, fluorescent lights, and
electrical appliances.
If the interference is severe, turn off the interfering device.
Move the handset closer to the base.
Hang up and redial the number.
Press CH to change the channel.
The range decreases.
Ensure the base’s antenna is raised and is not touching a metal
surface.
Recharge the handset’s battery pack.
The handset battery pack does
not charge.
Check the charging contacts on the handset and base. If they are
dirty, clean them with a pencil eraser.
Be sure the battery pack is connected correctly.
Be sure the handset is properly seated on the base.
Replace the battery pack (see “Connecting, Charging, and
Replacing the Battery Pack” on Page 7).
You have an incoming call, but
do not receive any Caller ID
information.
Check that the phone is correctly and securely connected.
Check with you phone company to verify that your Caller ID service is active.
If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot locate the problem, take your phone
to your local RadioShack store for assistance.
Troubleshooting
15
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one (1) year from the date of purchase from RadioShack company-owned stores and
authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES
NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED
HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING
FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise
provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the
product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and
products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts
and products are warranted for the remainder of the original warranty period. You will be charged for repair
or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those
provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation,
set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
RadioShack Corporation
Fort Worth, Texas 76102
12/99
43-3504 A
086-002147-017
08A01
Printed in China