Acer AIR-204 Technical information

TravelMate3010
Service Guide
Service guide files and updates are available
on the AIPG/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate3010 service guide.
Date
2
Chapter
Updates
Copyright
Copyright © 2006 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium 4 and Celeron are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
3
Conventions
The following conventions are used in this manual:
4
Screen messages
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
5
Chapter 1 System Specifications 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TM 3010 Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Easy-Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . 19
Hardware Specifications and Configurations . . . . . . . . . . . . 29
Chapter 2 System Utilities 38
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
40
42
44
47
48
Chapter 3 Machine Disassembly and Replacement 49
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . .
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the miniPCI/Memory/HDD Module/Keyboard . . .
Seperate the LCD module and main unit . . . . . . . . . . . . . . .
Disassemble the main unit. . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD module disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . .
HDD Disassembly and Reassembly . . . . . . . . . . . . . . . . . . .
50
51
52
53
55
56
59
61
Chapter 4 Troubleshooting 62
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On Self-Test (POST) Error Message . . . . . . . . . . . .
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . .
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . .
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
66
67
69
73
77
78
Chapter 5 Jumper and Connector Locations 79
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
FRU (Field Replaceable Unit) List 81
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Chapter 1
1
Chapter 1
System Specifications
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Performance
T
Intel® CoreTM Duo processor T2300/T2400/T2500/T2600 with 667 MHz FSB
T
Clock speed up to 1.66/1.83/2.16 GHz
T
North Bridge:
Chipset
T
T
915GM
South Bridge:
T
ICH7M
Memory
T
DDRII 533/667 SDRAM
T
Two DDR SODIMM slots
T
Upgradeable to 2GB Memory for 32bit OS, 4G for 64bit OS
T
12.1” WXGA 200-nit high-brightness TFT LCD
T
1280x800 pixel resolution
T
16:10 viewing ratio, supporting simultaneous mlti-window viewing via Acer GridVista
Display
Graphics
T
UMA
T
UMA
VRAM
T
DVMT3.0, share 8MB, up to 128MB in OS
Audio
T
Intel HD(High Definition) Audio
T
S/PDIF support for digital speakers
T
Internal Microphone
T
Sound Blaster proTM and MS-Sound compatible
T
Two speakers, at lease 1W/9cc for each
T
PATA and SATA co-lay
T
9.5mm height, 2.5” HDD
T
Easily removable
Storage
Chapter 1
1
T
60/80/100/120GB
T
PCI Bus Master Enhanced IDE
T
Support Ultra DMA100, S.M.A.R.T
T
G-Sensor HDD protection
Communication
T
56Kbps V.90/V.92 modem card (MDC1.5)
T
PCI-E Giga LAN on board
T
Intel PRO/Wireless 3945ABG network connection solution(dual-band tri-mode 802.11 a/b/g) Wi-Fi
CERTIFIEDTM
T
2 built-in PIFA type Antenna (which has to be placed on the top of LCD on the sides of LCD latch)
T
Bluetooth 2.0 +EDR(Enhanced Data Rate)
I/O Ports
T
3 external USB 2.0 ports
T
IEEE 1394 port (6-pin)
T
Ethernet (RJ-45) port
T
Modem (RJ-11) port
T
External display (VGA) port(15-pin)
T
1 Microphones-in
T
1 Line-in jack
T
1 Headphone/Speaker/Line-out jack with SPDIF support
T
1 Infrared (FIR) port
T
1 DC-in jack for AC adaptor
T
1 PCMCIA (exchange with Express card wide type slot)
T
1 ezDock port
T
6-in-1 card reader
T
6-cell of 18650 Li-ion battery pack, (2400mAh)
T
3-cell of 18650 Li-lon battery pack, (2000mAh)
T
3-pin 90W AC adaptor
Battery
2
Chapter 1
Block Diagram
5
4
3
2
1
Block Diagram
PA@ PATA
SA@ SATA
HOST 133MHz/166MHz
MP@ MINI PCI
X'TAL
14.318MHZ
PCI-E 100MHz
MC@ MINI CARD
GS@ G-SENSOR
CPU
D
Clock Generator
VGA 96MHz
CLOCK GEN
ICS954310BG
G9@ 5789
Thermal Sensor
Yonah/Merom
P2
G7@ 5787
P5
D
INTEL Mobile_479 CPU
USB 48MHz
Page : 3,4
PCI 33MHz
Page : 2
Page : 34
+3V_S5
C
+5V
+10V
+1.8VSUS
1.8V / 0.9V
/ 2.5V
+1.8V
Page : 35
+0.9V
CRT Switch
1466
FCBGA
Page : 12
RGB
CRT
SN74CBTLV3257PWR
Page : 18
Page : 18
Page : 6 ~ 11
LVDS
LVDS
X'TAL24.576MHZ
USB3
+5VSUS
+3V
TVOUT
CALISTOGA-GM
DDR2 533/667
MHz
Channel B
DDR2-SODIMM
+5V_S5
+3VSUS
Docking
Page : 32
SDVO
Page : 12
+5VPCU
+3V_PCU
DVI
Page : 31
Channel A
DDR2-SODIMM
5V / 3.3V / 10V
DVI
Chrontel 7307
HOST BUS
533/667
MHz
REF 14MHz
Page : 17
C
DMI I/F
BT
IDE - HDD
Page : 20
ATA 66/100
Page : 25
AD25 REQ0# / GNT0# INT E/F/G#
AD19 REQ2# / GNT2# INT C/D#
PCI BUS
USB0,1,2
SYSTEM
ext
Page : 20
USB*3
SATA - HDD
TI
MINI PCI
ICH7-M
652 BGA
SATA
PCMCIA+1394
+6 IN 1
Azalia
Page : 25
1394
Page: 21
PCMCIA
Page: 22
USB7
PCI7412
CCD
USB 2.0
PCI-E
Page : 13~16
Page : 17
OSC
48MHZ
Page :20
Page :21~23
6 IN 1
X'TAL
32.768KHZ
+0.9VSUS
Page: 23
LPC
+2.5V
X'TAL
32.768K
X'TAL
32.768K
PCI-E CARD
/ WLAN
B
MDC 1.5
USB4
Page : 26
AUDIO CODEC
ALC883
AMP
B
Page : 26
1.5V / 1.05V
Page : 36
+1.5V
+1.05V
NS
G-SENSOR
KXP84-0200
NS
KBC(97551)
Page : 25
TPM 1.2
NEW CARD
SIO (87383)
MIC
USB5
Page : 27
Page : 29
ECHO
CANCELLATION
VP1020-G
LINEIN
INT
SPK
HP
OUT
Page : 26
X'TAL
25M
VCC_CORE
CPU CORE
Page : 33
Touchpad
Page : 30
Keyboard
Page : 27
Page : 30
COM
LPT
BROADCOM
10/100/1G LAN
5789M
AUDIO/B
LAN Switch
MAX4892
Page : 19
RJ45
Page : 19
BATTERY
CHARGER
A
FIR
PS2
Docking
Page : 37
A
DOCKING AUDIO
Page : 32
1
5
Chapter 1
4
3
2
1
3
TM 3010 Outlook View
A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC.
Open View
#
4
Item
Description
1
Camera
1.3 Mega Pixel CMOS video camera with 225 degree rotation
feature.
2
Display screen
Also called Liquid-Crystal Display(LCD), displays computer
output.
3
Easy-launch buttons Buttons for launching frequently used programs.
4
Status indicators
Light-Emitting Diodes(LEDs) that light up to show the status of
the computer’s functions and components.
5
Palmrest
COmfortable support area for your hands when you use the
computer.
6
CLick buttons(left,
center and right)
The left and right buttons function like the left and right mouse
buttons; the center button serves as a 4-way scroll button.
7
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse.
8
Microphone
Internal microphone for sound recording.
9
Keyboard
For entering data into your computer.
10
Power button
Turns the computer on and off.
Chapter 1
#
#
Icon
Front View
#
#
Icon
#
1
N/A
Icon
Icon
2
# #
Icon
Icon
"Launch keys" on page 10
Description
Item
"Launch keys" on page 10
Item
Description
Item
#
3
"Launch
keys" on page 10
Description
Item
Description
Item
Item
Description
Description
Speakers
Left and right speakers deliver stereo audio output.
Bluetooth
communication
button/indicator
Press to enable/disable Bluetooth function. Lights to
indicate the status of Bluetooth communications.
Item
Item
"Launch keys"
onDescription
page 10
Description
Wireless
Press to enable/disable Wireless function. Lights to
communications indicate the status of wireless LAN communications.
button/indicator (manufacturing option)
4
Power indicator
5
Battery indicator Indicates the computer’s battery status.
#
6
7
#
8
Icon
Icon
Indicates the computer’s power status.
ItemHeadphones/
Description
Connects
to audio line-out devices(e.g., speakers,
speaker/line-out headphones)
jack with
S/PDIF support
Mic-in jack
Item
Infrared port
Accepts inputs from external microphones.
Description
Interfaces with infrared devices(for TravelMate 4270/4670
Series)Note:
Left View
Chapter 1
5
Note:
#
Icon
1
2
Item
Description
External display (VGA)
port
#
Icon
#
Icon
Connects to display device(e.g., external monitor,
LCD projector)
Ethernet(RJ-45) port
Connects to an Ethernet 10/100/1000 based
Item
Description
network.
3
Item
Description
Modem(RJ-11) port
#
Icon
4
Item
Connects to a phone line.
Description
Two USB2.0 ports
Connect to USB 2.0 devices(e.g., USB mouse,
USB camera)
Right View
#
Item
#
Icon
#
Item
#
Description
Description
Icon
Item
1
Description
PC Card slot
#
2
Description
Item
Icon
Item
Accepts one Type II PC Card.
Note
Description
5-in-1 card reader
Accepts Secure Digital(SD),
MultiMediaCard(MMC), Memory Stick(MS),
Memory Stick Pro(MS PRO), and xD-Picture Card.
Note:Only one card can operate at any given time.
Note:
3
6
PC Card slot eject
button
Ejects the PC Card from the slot.
Chapter 1
#
#
Icon
Icon
Item
4
6
Description
Two USB 2.0 ports
#
5
Item
Icon
Item
Description
Connect to Universal Serial Bus (USB) 2.0 devices
(e.g., USB mouse, USB camera).
Description
#
Icon
Connects to IEEE 1394 devices
Item IEEE 1394 port(6Description
#
Icon
Item Ventilation slots Description
Enable the computer to stay cool, even after
pin)
prolonged use.
7
Kensington lock slot Connects to a Kensington-compatible computer
security lock
#
Icon
Item
Description
Note:
Rear View
#
Item
Description
Note
#
1
Icon
#
#
Item
Icon
Item DC-in Jack
Icon
Item
Description
Description
Connects to an AC adapter.
Description
2
Battery bay
Houses the computer’s battery pack.
3
124-pin Acer
ezDock connector
Connects to Acer ezDock(for TravelMate 4670 Series)
Chapter 1
7
Bottom View
#
8
Item
Description
1
Battery bay
Houses the computer’s battery pack.
2
Battery lock
Locks the battery in position.
3
Cooling fan
Helps keep the computer cool.
NOTE: Do not cover or obstruct the opening of the fan.
4
Ventilation slots
Enable the computer to stay cool, even after prolonged use.
5
Memory compartment
Houses the computer's main memory
6
Battery release latch
Releases the battery to remove the battery pack.
Chapter 1
#
Item
Description
Indicators
Your computer has seven easy-to-read status indicators, including four on the front panel.
"Launch keys" on page 10
#
Item
Description
"Launch keys" on page 10
#
Item
Description
The power, battery and wireless communication status indicators are visible even when the LCD display is
# closed.
Item
Description
Icon
Icon
#
Icon
Item
Function
Item
Description
Description
Description
"Launch
pageup10when Caps Lock is activated.
Caps Lock
activitykeys" onLights
#
#
#
Icon
Icon
Icon
"Launch keys" on page 10
Lights upwhen Num Lock is activated.
Item Num Lock activity
Description
HDD
Indicate when the hard disk drive is active.
Bluetooth
Indicates the status of Bluetooth communication.
Item
Wireless LAN
Item
Description
Indicates the status of wireless LAN communication.
Description
Power
Indicates the status of computer’s power status.
Battery
Indicates the computer’s battery status.
NOTE: The lights shows amber when the battery
is charging.
NOTE: The lights showns green when in AC
mode.
Chapter 1
9
"
Easy-Launch Buttons
"Launch
Manager"
on page
41 They are mail, Web browser, Empowering Key and one userLocated above the
keyboard
are four
buttons.
programmable button.
Easy-launch button
Item
10
Default application
Default Application
Mail
Email application(User-programmable)
Web Browser
Internet browser(User -programmable)
e
Acer Empowering Technology(User-programmable)
P
User programmable
Chapter 1
Touchpad
The build-in touchpad is a pointing device that senses movement on its surface.
This means the cursor responds as you move your finger across the surface of the touchpad.
The touchpad is located in the middle of the palm rest area, providing maximum comfort and efficiency.
Touchpad Basics
T
Move your finger across the touchpad(2) to(2)move the cursor.
(1)
(4)
T
Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad is the same as clicking the left button
T
Use the 4-way scroll (3) button
to scroll up or down and move left or right a page. This button
(3)
mimics your cursor pressing on the right scroll bar of windows applications.
Function
Left Button(1)
Righ Button(4)
Main touchpad(2)
Execute
Quickly click twice
Tap twice (at the
same speed as
double-clicking the
mouse button)
Select
Click once
Tap once
Drag
Click and hold.
Then slide your
finger across the
touchpad to drag
the cursor over the
selection.
Tap twice quickly; rest
your finger on the
touchpad on the
second tap and drag
the cursor.
Access
context
menu
Scroll
Center button(3)
Click once
CLick and hold to
move up/down/left/
right
NOTE: When using the touchpad, keep it-and your fingers-dry and clean. The touchpad is sensitive to finger
movement; hence, the lighter the touch, the better the response. Tapping harder will not increase the
touchpad’s responsiveness.
Chapter 1
11
Using the Keyboard
The full-sized keyboard includes an embedded numeric keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock keys and Embedded Numeric Keypad
The keyboard has four lock keys which you can toggle on and off.
Lock key
Description
The computer features three lock keys, each with its own status indicator light.
Lock Key
Caps Lock
Description
When Caps Lock is on, all alphabetic characters are typed in
<Fn> + <F11>
uppercase. Toggle on and off by pressing the Caps Lock key on the
left side of the keyboard.
Num lock
<Fn+F11>
<Fn> +
When Num Lock is on, the embedded keyboard is in numeric mode.
The keys function as a calculator(complete with the arithmetic
operators+,-,*, and /). Use this mode when you need to do a lot of
numeric data entry. A better solution would be to connect and
external keypad.
<F12>
Scroll lock
<Fn+F12>
When Scroll Lock is on, the screen moves one line up or down when
you press the up or down arrow keys respectively. Scroll Lock does
not work with some applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access
Num Lock on
Numer keys
on
Type numbers
in a normal
Desired
access
Num
Lock manner
on
embedded keypad
Cursor-control keys Hold <Shift> while using cursoron embedded
control keys.
keypad
Main keyboard
keys
<Shift>
Hold <Fn> while typing letters on
embedded keypad.
Num Lock off
Num Lock off
Hold <Fn> while using cursor-control
keys.
<Fn>
Type the letters in a normal manner.
<Fn>
12
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functoins.
Windows logo key
Pressed alone, this key has the same effect as clicking on the
Windows Start button; it launches the Start menu. It can also be
used with other keys to provide a variety of functions:
+ Tab (Activates the next Taskbar button)
+ E (Opens the My Computer window)
+ F1 (opens Help and Support)
+ Tab
+F (opens the Find: All Files dialog box)
+E
+ F1
++ FM (minimizes all windows)
+M
Shift +
<Shift> +
+M
+ M+(undoes
the minimize all windows action)
M
+R
+ R (opens the Run dialog box)
Application key
This key has the same effect as clicking the right mouse button; it
opens the application’s context menu.
Hotkeys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the <Fn> key before
pressing the other key in the hotkey combination.
Fn
Hot
Icon
key
Chapter 1
Fn F1
Function
Description
13
Hot Key
Fn+F1
Icon
Fn-F1
Fn-F1
Fn-F1
Fn-F1
Fn-F2
Fn-F2
Fn+F2 Fn-F2
Item
Hot key help
This key will cause a help
message to appear on the display
device that describes the definition
and functionality of the unit hot
keys.
Acer eSettings
Launches the Acer eSetting in
Acer Empowering Technology.
See “Acer Empowering
Technology”
Acer ePower
Management
Launches the Acer ePower
Management in Acer Empowering
Technology. See “Acer
Empowering Technology”
Sleep
Puts the computer in Sleep mode
Display toggle
Switches display output between
the display screen, external
monitor(if connected)and both .
Screen blank
Turns the display screen backlight
off to save power. Press any key
to return
Touchpad toggle
Turns the internal touchpad on
and off
Speaker toggle
Turns the speakers on and off
Volume up
Increases the sound volume
Volume down
Decreases the sound volume
Brightness up
Increases the screen brightness
Brightness down
Decrease the screen brightness
Fn-F2
Fn-F3
Fn+F3 Fn-F3
Fn-F3
Fn-F3
Fn+F4
Fn-F4
Fn-F4
Fn-F5
Fn-F4
Fn-F5
Fn+F5 Fn-F5
Fn-F4
Fn-F5
Fn-F5
Fn-F5
Fn-F5
Fn+F6
Fn+F7
Fn+F8
Fn+w
Fn+y
Fn+x
Fn+z
14
Fn-F6
Fn-F5
Fn-F6
Fn-F6
Fn-F6
Fn-F6
Fn-F6
Fn-F7
Fn-F7
Fn-F6
Fn-F7
Fn-F7
Fn-F7
Fn-F6
Fn-F8
Fn-F8
Fn-F7
Fn-F7
Fn-F8
Fn-F8
Fn-F8
FnFn-F8
Fn-F7
FnFn-F8
FnFnFnFn-F8
FnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnFnHome
Home
FnFnFnFnHome
FnHome
Home
Home
FnFnFnPg
Home
PgUp
Up
FnFnFnFnHome
Pg Up
FnPg
Up
FnPg
Up
FnPg
Up
FnPg
Dn
Pg
Fn- Dn
Fn-Up
FnPg
FnPg
Dn
FnPg
Up
PgDn
Dn
Pg
Pg Dn
FnFn-End
Fn-End
Fn-Dn
Pg
Fn-End
Pg
Dn
Fn-End
Fn-End
Fn-End
Fn-End
Fn-End
Description
Chapter 1
Special Keys
You can locate the Euro symbol and the US dollar sign at the upper-center of your keyboard.
The Euro Symbol
1.
Alt Gr>
Open a text editor or word processor.
2.
Either press <
<5>
Alt Gr>
at the bottom-right of the keyboard, or hold <Alt
Gr> and then press the <5> key at
> ><5>
Alt Gr>
th
<5>
the upper-center ofNote
the keyboard.
Note
www.microsoft.com/typography/faq/faq12.htm
NOTE: Some fonts and software
do not support the
Euro symbol. Please refer to www.microsoft.com/
www.microsoft.com/typo
graphy/faq/faq12.htm
Note
typography/faq/faq12.htm for more information.
www.microsoft.com/typo graphy/faq/faq12.htm
The US Dollar Sign
1.
Open a text editor or word processor.
2.
Either press <
> at the bottom-right of the<4>
keyboard, or hold
<Shift> and then press the <4> key at
<Shift>
<Shift>
th
<4>
<4>
the upper-center of the keyboard.
<Shift>
NOTE: This function varies according to the language settings.
Note:
Note:
Note:
Chapter 1
15
Using theNote:
System Utilities
Acer GridVista(dual-display compatible)
To enable the dual monitor
feature of your notebook, first Start
ensure that
the second
monitorDisplay
is connected, then,
Control
Panel
Note:
select Start, Control Panel, Display and click on Settings.
Settings
(2)Select the secondary monitor (2) icon in the
display box and then click the check box Extend my Windows desktop onto this monitor. Finally, click Apply to
Extend
Windows
desk
top onto this monitor
confirm the new settings
and clickmy
OK to
complete the
process.
Apply
OK
Note:
Start Control Panel Display
(2)
Extend my Windows desk top onto this monitor
OK
Settings
Apply
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access this function, please go to Start, All Programs and click on Acer GridVista.
You may choose any one of the four display settings indicated below:
All Programs
Start All Start
Programs
1
2
1
Acer GridVista
Acer GridVista
2
1
3
2
3
1
3
2
4
Double(vertical), Triple(primary at left), Triple(primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned independently.
Set up Procedure
1.
Run Acer GridVista and select your preferred screen configuration for each display from the taskbar.
2.
Drag and drop each window into the appropriate grid.
3.
Enjoy the convenience of a well-organized desktop.
NOTE: The system utilities work under Microsoft Windows XP only.
16
Chapter 1
Note:
Launch Manager
Launch Manager allows you to set the four easy-launch buttons located above the keyboard. You can access
"Easy-launch
on page and
22 then Launch Manager to start the application.
the Launch Manager by clicking
on Start, buttons"
All Programs,
Start All Programs
Norton AntiVirus
Launch Manager
Norton AntiVirus is an anti-virus software that finds and repairs infected files, and protects against viruses to
keep your computer data safe and secure.
How do I check for viruses?
A Full System Scan scans all files on your computer. To perform a system scan:
1.
Start Norton AntiVirus.
Double click on the Norton AntiVirus icon on the desktop or click on the Start menu in the Windows
taskbar, highlight Programs, and select Norton AntiVirus.
2.
Norton AntiVirus
Start
Programs
In the Norton AntiVirus
main window, click Scan for Viruses.
Norton AntiVirus
Scan for Viruses
3.
Scan
for Viruses
Scan My Computer
In the Scan for Viruses
panel,
click Scan My Computer.
4.
Under Actions, click Actions
Scan.
5.
When the scan is complete, a scan summary appears. Click Finished.
Chapter 1
Scan
Finished
17
You can schedule customized virus scans that run unattended on specific dates and times or at periodic
intervals. If you are using the computer when the scheduled scan begins, it runs in the background so that you
do not have to stop working.
For more information refer to the Norton Antivirus Help menu.
18
Chapter 1
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and
manage your new Acer notebook. It features the following handy utilities:
T
T
T
T
T
T
T
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.
Acer eLock Management limits access to external storage media.
Acer ePerformance Management improves system performance by optimizing disk space, memory and
registry settings.
Acer eRecovery Management backs up/recovers data flexibly, reliably and completely.
Acer eSettings Management accesses system information and adjusts settings easily.
Acer ePower Management extends battery power via versatile usage profiles.
Acer ePresentation Management connects to a projector and adjusts display settings conveniently.
For more information, press the <
> key to launch the Empowering Technology menu, then click on the
appropriate utility and select the Help function.
Acer eDataSecurity Management
Acer eDataSecurity Management is handy file encryption utility that protexts your files from being accessed by
unauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and
Chapter 1
19
easy data encryption/decryption and also supports on-the-fly file encryption for MSN Messager and Microsoft
Outlook.
There are two passwords that can be used to encrypt/decrypt a file; the supervisor passowrd and the filespecific password. The supervisor passwork is a “master” password that cna decrypt any file on your system;
the file-specific password will be used to encrypt files by default, or you cna choose to enter your own filespecific password when encrypting a file.
NOTE: The password used encrypt a file is the unique key that the system needs to decrypt it. If you lose the
password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt your encryped file! Be sure to safeguard all related
passwords!
20
Chapter 1
Acer eLock Management
Acer eLock Management is a security utility that allows you to lock up your removable data, optical and floppy
drives to ensure that data can’t be stolen while your notebook is unattended.
T
T
T
Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be
mounted as a file system when plugged into the system.
Optical drive deivces - includes any kind of CD-ROM or DVD-ROM drives.
Floppy disk drives - 3.5-inch disks only.
To activate Acer eLock Management, a password must be set first. Once set, you may apply lock to any of the
three kinds of devices. Lock(s) will immediately be set without any reboot necessary, and will remain locked
after rebooting, until unlocked.
If you do not set a password, Acer eLock Management will reset back to the initial status with all locks
removed.
NOTE: If you lose your password, there is no method to reset it except by reformatting your notebook or taking
your notebook to anAcer Customer Serivce Center. Be sure to remember or write down your password.
Chapter 1
21
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of your Acer
notebook. It provides you with the following options to enhance overall system performance:
T
T
T
22
Memory optimization - releases unused memory and check usage.
Disk optimization - removes unneeded items and files.
Speed optimization - improves the usability and performance of your Windows XP system.
Chapter 1
Acer eRecovery Management
Acer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by
the manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on your
system’s HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides you
with:
T
T
T
Password protection.
Recovery of applications and drivers.
Image/data backup:
T
T
Back up to HDD (set recovery point).
T
Back up to CD/DVD.
Image/data recovery tools:
Chapter 1
T
Recover from a hidden partition (factory defaults).
T
Recover from the HDD (most recent user-defined recovery point).
T
Recover from CD/DVD.
23
NOTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To
ensure the best results when recovering your system using a CD or Acer eRecovery Management,
detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer
ezDock.
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specifications and to monitor the system health
status. Furthermore, Acer eSettings Management enables you to optimize your Windows operating system, so
your computer runs faster, smoother and better.
Acer eSettings Management also:
T
T
T
T
T
24
Provides a simple graphical user interface for navigating through the program effortlessly.
Displays general system status and advanced monitoring for power users.
Logs when a hardware component has been removed or replaced.
Permits you to migrate personal settings.
Keeps a history log of all alerts that were previously issued.
Chapter 1
Acer eNet Management
Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a
variety of locations. To access this utility, either click on the “Acer eNet Management” icon on your notebook,
or start the program from the Start menu. You also have the option to set Acer eNet Management to start
automatically when you boot up your PC.
Acer eNet Management automatically detects the best settings for a new location, while offering you the
freedom to manually adjust the settings to match your needs, simply by right-clicking on the icon in the taskbar.
Acer eNet Management can save network settings for a location to a profile, and automatically apply the
appropriate profile when you move from one location to another. Settings stored include network connection
Chapter 1
25
settings(IP and DNS settings, wireless AP details, etc.), as well as default printer settings. Security and safety
concerns mean that Acer eNet Management does not store username and password information.
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface, or double-click the Acer ePower Management icon
in the task tray.
Acer Mode
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other
settings, or click on buttons to turn the following functions on/off: Wireless LAN, Bluetooth, CardBus, Memory
Card, Audio, and Wired LAN.
DC Mode
To suit your usage, there are four pre-defined profiles - Entertainment, Presentation, Word Processing, and
Maximum Battery. Or, you can define up to three of your own profiles.
Create new power scheme
1.
Assign a name for the new scheme.
2.
Choose existing scheme to use as a template.
3.
Select whether used for mains (AC) or batery mode.
4.
Choose which power options best fit your needs, then click OK.
5.
The new profile will appear on the main screen.
Battery status
For real-time battery life estimates based on current usage, referto the panel on the lower left-hand side of the
window.
26
Chapter 1
You can also click “Advanced Settings” to:
T
T
T
T
Set alarms.
Re-load factory defaults.
Select what actions will be taken when the cover is closed, and set passwords for accessing the system
after Hibernation or Standby.
View information about Acer ePower Management.
Chapter 1
27
Acer ePresentation Management
Acer ePresentation Management lets you select from two of the most common projector resolutions: XGA and
SVGA.
28
Chapter 1
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
®
TM
Intel Core Duo processor T2300/T2400/T2500/T2600 with 667 MHz FSB
Clock speed up to 1.66/1.83/2.16 GHz
CPU package
Micro-FCPGA
CPU core voltage
Depend on DVI
CPU I/O voltage
1.2875V
System Board Major Chips
Item
System core logic
Controller
®
Intel 945GM/ICH7M
Super I/O controller
SIO 87383, LPC interface
Audio controller
Azalia Audio Controller ALC883D
Video controller
UMA
Hard disk drive controller
ICH7M
Keyboard controller
NS 97551
IrDA controller
Vishay TFBS6614
DVI controller
CH7307
PCMCIA/ card reader / 1394
controller
TI PCI7412
DDR-soDIMM controller
945GM
BIOS
Item
Specification
BIOS vendor
Phoenix
BIOS Version
Phoenix First BIOS
BIOS ROM type
1MB CMOS Boot Block Flash Memory
BIOS ROM size
1MB
BIOS package
40 pin TSOP
BIOS password control
Set by setup manual
Chapter 1
29
System Memory
Item
Specification
Memory controller
945GM
Memory size
256MB/512MB/1G
DIMM socket number
2
Supports memory size per slot
1024 MB
Supports maximum memory size
2GB (with dual soDIMM modules)
Supports DIMM type
DDRII SDRAM Standard
Supports DIMM Speed
533/667 MHz
Supports DIMM voltage
1.8V
Memory module combinations
You can install memory modules in any combinations as long as
they match the above specifications.
.
LAN Interface
Item
Specification
Supports LAN protocol
10/100/1000 Mbps Fast Ethernet connection
LAN chip
Broadcom 5789 PCI-E GbE
LAN connector type
RJ45
Feature
Support WOL from S5, support LDCM
.
Wireless LAN
Item
Specification
Card Type
Mini-card
Mode
802.11 a/b/g(Mini-Card)
802.11 pre-n
Antenna
Built in 2 antenna(Has to be placed on the top of LCD
on the sides of LCD latch)
Support
Wi-Fi, WPA2, WMM, CCX V3/V4
.
Modem Interface
Item
Specification
Data modem data baud rate (bps)
56K ITU
Supports modem protocol
V.90/V.92, WWDAA
Apply CISPR22
Wake-on-Ring ready
Modem connector type
RJ11
VGA
Notice
30
UMA
Chipset for suitable VGA type
945GM
Video RAM
up to 128MB
Chapter 1
USB Port
Item
Specification
USB compliancy level
2.0
OHCI
USB 2.0
Number of USB port
3
Location
Left Side *2
Right Side *1
Audio Port
Item
Specification
Audio Controller
Azalia Audio Controller (Realtek ALC883)
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
SNR>85, High-performance DACs with 95dB SNR, ADCs 85 dB
SNR
Compatibility
Microsoft PC99/2100, AC97 2.3 & WHQL/WLP2.0
Mixed sound source
CD
Sampling rate
All DACs support 44.1K/48K/96K/192K sample rate
All ADCs support 44.1K/48K/96K sample rate
Internal microphone
one internal microphone(2 digital picrophone array)
Internal speaker / Quantity
Yes / 2(at least 1.5W/30cc for each)
Support
VoIP/Universal jack
PCMCIA Port
Item
Specification
PCMCIA controller
PCI7412
Supports card type
Type II
Number of slots
One
Access location
Right Side
Supports 32 bit CardBus
Yes
Keyboard
Item
Specification
Keyboard controller
NS PC97551
Keyboard vendor & model name
New Acer Ergo keyboard
Total number of keypads
Touchpad with 4-way integrated scroll button
Chapter 1
T
88-89 keys Acer Fine TouchTM
keyboard
Yes
31
Keyboard
Item
Specification
Feature
Four easy-launch buttons
T
Support Windows keys and application
keys
T
Standard pitch, 2.5 mm travel length
T
Hotkey controls
T
embedded numberic keypad
T
Multi-Langue support
T
Spill-proof
T
Internet browser
T
email with LED
T
Empowering key
T
one user-programmable button
Battery
Item
Specification
Vendor & model name
Panasonic/Sanyo
Battery Type
Li-ion
Number of battery cell
6-cell 2400mAh
3-cell 2000mAh
Package configuration
Pin 1
Pin 2
BATT+: Battery+, Battery Positive Terminal
Pin 3
ID : Identify Pin (Note 1)
Pin 4
B/I : Battery-In Pin
Pin 5
TS : Connect to Thermister
Pin 6
SMD : SMBus data interface I/O pin
Pin 7
SMC : SMBus clock interface I/O pin
Pin 8
Pin 9
GND : Battery Negative Terminal
12.1” LCD Panel
Item
32
Specification
Vendor & model name
AUO B121EW01 V3
AUO B121EW02 V5
QDI
QD12TL02-01/
QD12TL02-02
CMO
N121|3-L 01/
N121|3-L02
Screen Diagonal (mm)
12.1” WXGA
12.1” WXGA
12.1” WXGA
Active Area (mm)
261.12(W)163.2(H)
261.12(W)x163(H)
261.12(H)x163.2(V)
Display resolution (pixels)
1280x3(RGB)x800
1280x800
1280xRGBx800
Pixel Pitch(mm)
0.204(per on
triad)x0.204
0.2055(W)x0.2055(H)
0.204x0.204
Pixel Arrangement
RGB vertical stripe
RGB vertical stripe
RGB vertical stripe
Display Mode
Normally white
Normally white
Normally white
Chapter 1
12.1” LCD Panel
Item
Specification
Surface Treatment
Hard coating(3H) glare
type/anti-glare type
Hard coating(3H) glare
type/anti-glare type
Hard coating(3H)
glare type/anti-glare
type
Typical White Luminance (cd/m2)
180(Typical)
200(Center Typical)
200(Typical)
Contrast Ratio
400 :1(Min)
300:1(Min)
500(Typical)
Response Time (Optical Rise
Time+Fall Time)msec
25(Typical)
35(Max)
50(Max)
25(Typical)
35(Max)
Normal Input Voltage of Power
Supply
+3.3V(Typical)
+3.3V(Typical)
+3.3V(Typical)
Power Consumption (watt)
4.5(Typical)
4.8(Typical)
3.66(typ) IL=6.0
Weight
280g (0.5mm glass)
250g
260(Typical)
Physical Size(mm)
275.82(H)x178(V)x5.2(
D) (Max)
275..82(H)x178(V)x5.2(
D)(Max)
275.8(H)x178(V)x4.9(
D)(Typical)
Electrical Interface
1 channel LVDS
LVDS interface
system(H-Sync, VSync)
3.3V LVDS with 1
pixel/clock
Support Color
Native 262K colours
256K colors
Native 262K colours
40/40
10/30
45/45
15/35
45/45
20/45
0 to +50
-40 to +60
0 to +50
-25 to +60
0 to +50
-25 to +60
also called Brightness
Viewing Angle (degree)
Horizontal: Right/Left
Vertial: Upper/Lower
Temperature Range( ° C)
Operating
Storage (shipping)
AC Adapter
Item
Vendor & model name
Specification
LITEON-65W, PA-1650-02 QY YELLOW 1.7X5.5X11 LF
Input Requirements
Maximum input current (A,
@100Vac, full load)
1.6A @100Vac input and maximum load
Nominal(Rated) frequency
(Hz)
50 or 60 and single phase
Frequency variation range
(Hz)
47 - 63
Nominal voltages (Vrms)
100-127(low range)
200-240(high range)
Efficiency
High efficiency 83% minimum, full load, warm-up condition.
Output Ratings (CV mode)
Rated output voltage
Offers rated output voltage 19.0V
Voltage Range
18.05V to 19.95V
Noise + Ripple
380mV
Rated Power
65Watts continuously at all specified conditions
Output current
0 A (min.)
to 4.74A (max.)
Dynamic Output Characteristics
Start-up time
Chapter 1
Shall less than 5 sec
33
Item
Specification
Hold up time
at least 5ms (@115 Vac input, full load)
Over Voltage Protection
(OVP)
29V
Over Current
Protection(OCP)
Output current limit is 5A(Max mode)
Short circuit protection
Output can be shorted without damage, and auto recovery
Electrostatic discharge
(ESD)
15kV (at air discharge)
8kV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
2150VDC for 1 sec
Leakage current
less than 100uA
Regulatory Requirements
1. CISPR 22 Class B
2. VCCI Class II
Hard Disk Drive Interface
Item
Specification
Vendor &
Model Name
Segate SATAST98823AS/
HGST
SATA 1.5G NCQ
MORAGA+HTS541080G9SA
00
Segate SATA ST9100824AS
LF/HGST
NCQMORAGA+HTS541010
G9SA00
Segate SATA
ST9120821AS LF/
Toshiba SATAI1.5G W/
NCQ MK1234GSX
Capacity
(MB)
80000
100000
120000
Bytes per
sector
1024/512
512
512
Data heads
3/4
4
4
Disks
2
2
2
Spindle
speed
(RPM)
5400 RPM
5400 RPM
5400 RPM
Drive Format
Performance Specifications
Buffer size
8192KB
8192KB
8192KB
Interface
Serial ATA
Serial ATA
Serial ATA
Max. media
transfer rate
(disk-buffer,
Mbytes/s)
57.6/61.6
57.6/61.6
57.6
Data transfer
rate
(host~buffer,
Mbytes/s)
150 MB/Sec.
SATA 1.0
150 MB/Sec.
150 MB/Sec.
5V(DC) +/- 5%
5V(DC) +/- 5%
DC Power Requirements
Voltage
tolerance
34
5V(DC) +/- 5%
Chapter 1
8X DVD Dual Interface
Item
Vendor & model name
Specification
Lite-On SOSW-833S
PANASONIC UJ-840
(1) Read
DVD-ROM(single layer) : 1.7-4X, 2.56X, 3.3-8X(CAV)
DVD-ROM(dual layer) : 1.7-4X, 2.56X(CAV)
DVD+R : 1X,2.4X(CLV) / 1.7-4X, 2.56X, 3.3-8X(CAV)
DVD+RW : 1X, 2.4X(CLV) / 1.7-4X,
2.5-6X(CAV)
Double layer DVD+R: 1X, 2.4X(CLV) /
1.7-4X(CAV)
Double layer DVD-R: 1X, 2.4X(CLV) /
1.7-4X(CAV)
DVD-R : 1X, 2X / 1.7-4X, 2.5-6X, 3.38X(CAV)
DVD-RW : 1X, 2X / 1.7-4X, 2.56X(CAV)
CD-ROM, Finalized CD-R, CD-RW :
Data/CD-DAE/Video CD : 4.1-10X,
6.2-15X, 8.3-20X, 10-24X
Unfinalized CD-R/RW : 4X/8X(CLV)
DVD-ROM : MAX 8X CAV
CD-ROM : MAX 24X CAV
(2) Write
CD-R : 10X, 24X
Low speed CD-RW: 4X
High Speed CD-RW : 4X, 10X
Ultra Speed CD-RW : 10X, 24X
DVD+R : 2.4X, 4X, 6X, 8X
DVD+R DL : 2.4X
DVD+RW : 2.4X, 4X
DVD-R : 2X, 4X, 6X, 8X
DVD-RW : 2X, 4X
CD-R : Max 24X Zone CLV
CD-RW : 4X CLV
High Speed CD-RW : 10X CLV
Ultra Speed CD-RW : 10X CLV
DVD+R : Max 8X Zone CLV
DVD+R DL : 2.4X CLV
DVD+RW : Max. 4X Zone CLV
DVD-R : Max. 8X Zone CLV
DVD-RW : Max. 4X Zone CLV
(3) ATAPI Interface
PIO mode
DMA mode
Ultra DMA mode
16.6MB/s: PIO mode4
16.6MB/s: Multi word mode2
33.3MB/s: Ultra DMA mode2
16.6MB/s: PIO mode4
16.6MB/s: Multi word mode2
33.3MB/s: Ultra DMA mode2
Buffer Memory
2MB
2MB
Interface
ATA/ATAPI-6, MMC-4
Enhanced IDE(ATAPI) compatible
Applicable disc format
CD-DA, CD-TEXT, CD ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 Form-2,
CD-I Ready, Video-CD (MPEG-1),
Photo-CD, Enhance CD, CD extra, ITrax CD and UDF, DVD-ROM, DVDVideo, DVD-VIdeo, DVD-R single/multi
border(s), DVD+R single/multi
session(s), DVD-RW, DVD+RW
DVD: DVD-VIDEO,DVD-ROM, DVDR(3.9GB, 4.7GB), DVD-RW (Ver1.1)
DVD+R, DVD+R DL, DVD+RW
CD: CD-Audio, CD-ROM, CD-R/RW CDROM XA, , PhotoCD (Single and Multi
Session), Video CD, CD-Extra (CD+), ,
CD-Text, Hybrid SACD
Loading mechanism
Load: Manual load/DC brushless motor
system
Load: Manual
Release: (a) Electrical Release
Power Consumption
Max. 1500 mA
Max. 1800 mA
Input Voltage
5 V +/- 5 % (Operating)
5 V +/- 5 % (Operating)
Performance Specification
Transfer rate (KB/sec)
Chapter 1
35
Combo Drive Interface
Item
Specification
Vendor & model name
LITEON SOSC-2483K
PANASONIC UJDA-770
Transfer rate (KB/
sec)(DVD)
Sustained:
Max 10.1Mbytes/sec
Sustained:
Max 10.8Mbytes/sec
Access Time(Typical)
DVD: Random Access: 100 ms
DVD:Full Stroke: 190 ms
DVD: Typical:180 ms
Buffer Memory
2MB
2MB
Interface
Compliant to ATA/ATAPI-5, MMC- ATAPI interface
3
Applicable disc format
CD-DA, CD ROM Mode-1, CDROM/XA Mode-2 Form-1 and
Form-2, CD-I Ready, VideoCD(MPEG-1), Karaoke-CD,
Photo-CD, Enhance CD, CD
extra, I-Trax CD and UDF
CD: CD-DA, CD-ROM,
CD-R, CD-RW, CD-ROM
XA,
PhotoCD(MultiSession)
DVD: DVD-ROM, DVDVideo, DVD-RAM(2.6GB/
4.7GB), DVD-R, DVDRW(Ver1.1), DVD+R,
DVD+RW
Loading mechanism
Load: Manual load/DC brushless
motor system
Load: Manual
5 V +/- 5 % (Operating)
5 V +/- 5 % (Operating)
Performance
Specification
Power Requirement
Input Voltage
Power Management
ACPI Mode
36
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned
off completely.
Working (G0/S0)
Individual devices such as the CPU and hard disk may be
power managed in this state.
Sleeping State (S3)
CPU Power Down
VGA Power Down
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
Super I/O Power Down
Sleeping State (S4)
Also called Hibernate state. System saves all system
states and data onto the disk prior to power off the whole
system.
Chapter 1
Dimensions and Weight
Item
Model
Deminsions
Weight
Details
Aspire 1690
Aspire 3510
297.5mm(W) x 210mm(D) x 24.5mm(H)
<1650g (12.1”/6-cell w/ Camera)
<1500g (12.1”/3-cell w/ Camera)
Environmental Requirements
Item
Specification
Temperature
Operating
+5 ~ +35°C
Non-operating
-20 ~ +65°C (storage package)
Humidity
Operating
20% ~ 80% without condensation
Altitude
Operating sea level 0 to 10,000ft
Storage sea level 0 to 40,000ft
Chapter 1
37
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However,
if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
The setup screen displays BIOS as follows:Navigating the BIOS Utility
Function
Item
Information
Display the system informations
Main
Allows the user to specify standard IBM PC AT
system parameters
Advanced
Provides advanced settings of the system
Security
Provides security settings of the system
Boot
Allows the user to specify the boot options
Exit
Allows the user to save CMOS setting and exit Setup
During setup,all Fn function keys and power saving functions are disabled.
There are five menu options: Main, Advanced, Security, Boot and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press p or q.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
Chapter 2
38
Information
PhoenixBIOS Setup Utility
. Info.
Main
CPU Type:
:
CPU Speed
:
Advanced
Security
Boot
Exit
Genuine Intel(R) CPU T2600@2.16GHz
2130 MHz
IDE1 Model Name:
ST9100824AS
IDE1 Serial Number: 3PL022FK
System BIOS Version: v0.2404b
VGA BIOS Version:
Napa 1256
KBC Version:
V0.020
Serial Number:
LXT123ZH2000470082EF00
Asset Tag Number:
Product Name:
Manufacturer Name:
TravelMate 3010
Acer
UUID:
00980420B0640010BA0A00C09FF974C3
F1 Help
↑ ↓
←→
Esc Exit
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
Parameter
39
Description
CPU Type
This item will show the CPU information of the system.
CPU Speed
This item will show the CPU clock speed.
IDE1 Model Name
This item will show the Model name of HDD installed on Primary IDE
master. The hard disk model name is automatically detected by the
system. If there is no hard disk present or unknown type, “None”
should be shown on this field
IDE1 Serial Number
This item will show the Serial number of HDD installed on Primary IDE
master. If no Hard disk or other devices are installed on Primary IDE
master, then it will display a blank line
System BIOS Version
This field reports the BIOS version of system
VGA BIOS Version
This field reports the VGA version of the system
KBC Version
This field reports the keyboard controller version of the system
Serial Number
This item will show the Serial number of system.
Asset Tag Number
This item will show the Asset Tag number of the system.
Product Name
This field will show product name.
Manufacturer Name
This field will show manufacturer name.
UUID
This will be visible only when there is an internal LAN device present.
Chapter 2
Main
This menu provides you the information of the system.
PhoenixBIOS Setup Utility
Info.
Advanced
Main
Security
Boot
Exit
Item Specific Help
System Time:
[11:59:38]
System Date:
[01/16/2006]
System Memory:
640 KB
Extended Memory:
1014 KB
Video Memory
128 MB
Quiet Boot:
[Enabled]
Power on Display:
[Auto ]
Network boot
[Enabled]
F12 Boot Menu:
[Disabled]
D2D Recovery:
[Enabled]
F1 Help
Esc Exit
↑↓
←→
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Parameter
Description
System Time / System
Date
The hours are displayed with 24 hours format. The values set in these two fields
take effect immediately.
System Memory
This field reports the memory size of system base memory. The size is fixed to
640KB.
Extended Memory
This field reports the memory size of the extended memory in the system.
Extended Memory size = Total memory size - 1 MB
Video Memory
VGA Memory size = 128MB
Quiet Boot
Customer Logo display will be shown during POST when it is selected.
Power on display
Auto: During power on process, the system will detect if any display
device is connected on external video port. If any external display device is
connected, the power on display will be in CRT (or projector) only mode.
Otherwise it will be in LCD only mode.
Both: Simultaneously enable both the integrated LCD screen and the system’s
external video port (for an external CRT or projector).
Network boot
When this is selected, Boot from LAN feature is enabled. When this is not
selected, Boot from LAN feature is then disabled.
Chapter 2
40
Parameter
41
Description
F12 Boot Menu
When this is selected, users can modify device boot priority by pressing F12 key
during POST. When this is not selected, device boot priority will not be
adjustable during POST.
D2D Recovery
Allow user to enable/disable the Disk-to-Disk recovery
Chapter 2
Advanced
The Advanced screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Serial Port:
[Auto]
Infrared Port(FIR):
[Auto]
Parallel Port:
Mode:
[Auto]
[ECP]
Boot
Exit
Item Specific Help
Configure serial port B
using oprions:
[Disabled]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when
controlled by OS
F1 Help
Esc Exit
↑ ↓
← →
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
Description
Serial Port
Chapter 2
Configure serial port A using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayedd when controlled
by OS
Option
Disabled
Enabled
Auto
42
Description
43
Option
Infrared Port
Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayedd when controlled
by OS
Disabled
Enabled
Auto
Parallel Port
Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayedd when controlled
by OS
Disabled
Enabled
Auto
Mode
Set the mode for the parallel port
Output only
Bi-directional
EPP
ECP
Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from
unauthorized use.
Info.
PhoenixBIOS Setup Utility
Security
Advanced
Main
Supervisor Password Is:
Clear
User Password Is:
Clear
Supervisor Password
controls accesses of the
setup utility.
[Enter]
Set HDD Password
HDD Password Is:
Password on Boot:
[Enter]
Clear
[Disabled]
Esc Exit
↑ ↓
←→
Exit
Item Specific Help
Set Supervisor Password
Set User Passord
F1 Help
Boot
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen. Settings in boldface are the default and
suggested parameter settings.
Parameter
Supervisor Password Is
Description
N/A
Option
N/A
User Password Is
N/A
N/A
HDD Password Is
N/A
N/A
Set Supervisor Password
Press Enter to set the administrator
password. When set, this password
protects the BIOS Setup Utility from
unauthorized access.
[Set]: System password is set
[Clear]: System password is not set
Length -- No more than 8
characters
Characters -- 0-9, A-Z (not
case sensitive)
Set User Password
Chapter 2
44
Parameter
Description
Option
Set HDD Password
When shown as [Locked], the hard drive
password currently can not be changed
or disabled.
To change or disable it, turn off the
system and enter Setup immediately after
turning it back on.
Press [Enter] to input change, or disable
hard drive password.
Enter
Password on boot
Defines whether a password is required
or not while the events defined in this
group happened. The following suboptions are all requires the Supervisor
password for changes and should be
grayed out if the user password was used
to enter setup.
Allows the user to specify whether or not
a password is required to boot.
Disabled
Enabled
Set Supervisor/User Password
If password on boot is required, the password must be set otherwise it cannot be enabled.
The formats of the password are as follows:
Length
Characters
No more than 8 characters
0-9,A-Z (not case sensitive)
While these fields are highlighted and press “Enter”, a window similar to the following is shown:
Set SupervisorPassword
Enter New Password
[
]
Confirm New Password
[
]
If there is an old password then setup will prompt with the following window instead and a current password
will be required to be entered at first:
Set Supervisor Password
45
Enter current password
[
]
Enter New Password
[
]
Confirm New Password
[
]
Chapter 2
User can now type password in field “Enter New Password”, and re-enter password in field “Confirm New
Password” for verification.
If the verification is OK:
The password setting is complete after user presses enter.
Setup Notice
Changes have been saved.
[ continue]
If the current password entered does not match the actual current password:
Setup Warning
Invalid password
Re-enter Password
[ continue]
If the new password and confirm new password strings do not match:
Setup Warning
Password do not match
Re-enter Password
Chapter 2
46
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable
devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM
in module bay and onboard LAN device.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Boot
Security
Item Specific Help
Boot priority order:
1: USB KEY:
2: USB FDC:
3: USB HDD:
4: IDE 0:
ST9100824ASIDE S
6: 1394 CDROM
7: PCI LAN: MBA v8.2.6 Slot 0300
8:
Excluded from boot order:
: PCI LAN:
: USB HDD:
: USB CDROM:
: USB FDC:
: USB KEY:
F1 Help
↑ ↓
MBA v8.2.6 Slot 0300
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Parameter
Boot priority order
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves
the device up or down.
<f> and <r> specifies
the device fixed or
removable.
<x> exclude or include
the device to boot.
<Shift + 1> enables or
disables a device.
<1- 4 > Loads default
boot sequence.
Select Item
←→
Esc Exit
Exit
Description
Keys used to view or configure devices: Up and Down
arrows select a device. <+> and <-> movew the device up
or down. <f> and <r> specifies the device fixed or
removable.
>
<x> exclude or include the device to boot.
<Shift +1> enables or disables a device.
<1-4> Loads default boot sequence.
.
47
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Exit
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS
Exit Discarding
Changes
Exit utility without saving Setup data to CMOS
Load Setup Default
Load default values for all SETUP items
Discard Changes
Load previous values from CMOS for all SETUP items
Save Changes
Save Setup Data to CMOS
Chapter 2
48
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Small Philips screw driver
T
Philips screwdriver
T
Plastic flat head screw driver
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
T
Chapter 3
49
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3. Remove the battery pack.
NOTE: TravelMate 3000 series product uses mylar or tape to fasten the FFC/FPC/connectors/cable, you may
need to tear the tape or mylar before you disconnect different FFC/FPC/connectors.
NOTE: There are several types of screws used to secure bottom case and upper case assembly. The screws
vary in length. Please refer the picture below, group the same type of screws together during service
disassembling. Please also remember the screw location for each screw type. If you fasten the screw to
the wrong location, the screw may be too long to damage the main board.
50
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Chapter 3
51
Removing the Battery Pack
52
1.
Release the battery lock.
2.
Slide the battery latch.
3.
Remove the battery pack.
Chapter 3
Removing the miniPCI/Memory/HDD Module/Keyboard
Removing the miniPCI and Memory
1.
Remove the two screws that secure the RAM door and remove the RAM door.
2.
Release the wireless antenna.
3.
Remove the two screws securing the miniPCI card.
4.
Press the latch on left and right side to pop out the miniPCI and remove it.
5.
Press the latch on left and right side to pop out the memory and remove it.
6.
Press the latch on left and right side to pop out the other memory and remove it.
Removing the HDD
1.
Remove the two screws that secure the HDD.
2.
Pull the HDD out and remove it from the main unit.
Removing the keyboard
1.
Open the LCD panel.
2.
Press the two inner keyboard latches that secure the keyboard with flat screw driver.
3.
Release another two outer keyboard latches.
4.
Pull the keyboard and trun it over.
Chapter 3
53
54
5.
Disconnect the keyboard FFC from the mainboard.
6.
Remove the keyboard from the main unit.
Chapter 3
Seperate the LCD module and main unit
1.
Disconnect the function key board FFC from the mainboard.
2.
Disconnect the LCD cable from the mainboard.
3.
Disconnect the touchpad board FFC from the mainboard.
LCD cable
Function keyboard
FFC
4.
Remove the three screws that secure the left and right hinge cover.
5.
Pull the left hinge up and slide it out as show.
6.
Pull the right hinge cover up and slide it out as show.
7.
Disconnect the function key board FFC from the function key board.
8.
Remove the screw that secures the function key board.
9.
Remove the function key board from the left hinge cover.
Touchpad FFC
10. Pull the wireless antenna out.
11. Remove the two screws securing the left and right hinges.
12. Detach the LCD module from the main unit.
Chapter 3
55
Disassemble the main unit
Separate upper and lower case
1.
Turn the main unit over.
2.
Remove the eighteen screws that secure the lower case.
3.
Detach the upper case from the lower case assembly.
Removing the Bluetooth module
1.
Tear off the mylar on the Bluetooth cable
2.
Disconnect the Bluetooth cable from the mainboard.
3.
Remove the two screws that secure the Bluetooth module.
4.
Remove the Bluetooth module from the mainboard.
5.
Disconnect the Bluetooth cable from the Bluetooth module.
Removing the MDC module
56
1.
Tear off the mylar on the MDC cable.
2.
Disconnec the MDC cable from the mainboard.
3.
Remove the MDC cable from the wire groove.
4.
Remove the two screws that secure the MDC board.
5.
Remove the MDC board from the mainboard.
Chapter 3
6.
Disconnect the MDC cable from the MDC board.
Removing the audio module
1.
Remove the screw that secures the audio board.
2.
Remove the audio board from the mainboard.
Removing the mainboard from lower case
1.
Press the button and remove the dummy card from the PCMCIA card slot.
2.
Disconnect the speaker cable from the mainboard.
3.
Disconnect the microphone cable from the mainboard.
Microphone cable
Speaker cable
4.
Remove the four screws that secure tha mainboard.
5.
Detach the mainboard from the lower case.
6.
Disconnect the power board cable from the mainboard and remove the power board from the mainboard.
7.
Remove the three screws that secure the thermal following the order 1, 2, 3.
Chapter 3
57
8.
Disconnect the fan cable from the mainboard.
9.
Remove the thermal module from the mainboard.
10. Tear off the mylar on the touchpad board FFC.
11. Disconnect the touchpad board FFC from the touchpad board.
12. Disconnect another FFC from the touchpad board.
13. Remove the two screws that secure the touchpad board.
14. Remove the touchpad board from the upper case.
15. This completes the main unit disassembly.
58
Chapter 3
LCD module disassembly
1.
Remove the six screw pads.
2.
Remove the six screws that secure the LCD bezel.
3.
Release the latches one by one. Please note that the bezel is fragile. Need to follow the following
disassembly pictures from left to right.
4.
Pull the bezel a little bit forward that paralleled LCD cover and remove the LCD bezel.
5.
Pull the inverter board out.
6.
Disconnect the LVDS cable from the inverter board.
7.
Disconnect the LCD cable from the inverter board.
8.
Remove the inverter board.
9.
Remove the four screws that secure the LCD and disconnect the CCD cable.
10. Remove the LCD from the cover assembly.
11. Remove the screw securing the CCD.
12. Remvoe the CCD from the cover assembly.
Chapter 3
59
13. Remove the wireless antenna from the cover assembly.
14. Remove the two screws that secure the left LCD bracket.
15. Remove the left LCD bracket from the LCD.
16. Remove the two screws that secure the right LCD bracket.
17. Remove the right LCD bracket from the LCD.
18. Turn the LCD back.
19. Tear off the tape on theLCD cable.
20. Disconnect the LCD cable from the LCD.
21. This completes the LCD disassembly.
60
Chapter 3
HDD Disassembly and Reassembly
1.
Remove the two screws that secure the HDD holder on on side.
2.
Remove the two screws that secure the HDD holder on the other side.
3.
Lift up the HDD and remove it from the HDD holder.
4.
Place the HDD back to the HDD holder
5.
Secure the HDD with two screws on one side.
6.
This complete the HDD module disassembly and reassembly.
Chapter 3
61
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test this model. Non-Acer products, prototype cards, or modified
options can give false errors and invalid system responses.
1.
Duplicate symptom and obtain the failing symptoms in as much detail as possible.
2.
Distinguish symptom. Verify the symptoms by attempting to re-create the failure by running the diagnostic
test or by repeating the same operation.
3.
Disassemble and assemble the unit without any power sources.
4.
If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You
can check the following:
power cords are properly connected and secured;
there are no obvious shorts or opens;
there are no obviously burned or heated components;
all components appear normal.
5.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 64.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 66
“Undetermined Problems” on page 78
POST detects an error and displayed messages
on screen.
“Error Message List” on page 67
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 66
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 66
“Intermittent Problems” on page 77
“Undetermined Problems” on page 78
Chapter 4
62
System Check Procedures
External Diskette Drive Check
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Numeric keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
63
Chapter 4
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T
Chapter 4
“Check the Battery Pack” on page 65
64
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
After rebooting, run Tracking Pad PS2 Mode Driver. For example, run Syn touch driver.
2.
Run utility with the PS/2 mouse function and check if the mouse is working.
3.
If the PS/2 mouse does not work, then check if the main board to switch board FPC is connected O.K.
4.
If the main board to switch board FPC is connected well, then check if the FCC on touch pad PCB
connects properly.
5.
If the FFC on touch pad PCB connects properly, then check if LS851 JP1 Pin6=5V are pulese. If yes, then
replace switch board. If no, then go to next step.
6.
Replace touch pad PCB.
7.
If the touch pad still does not work, then replace FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
65
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 78.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4
66
Index of Error Messages
Error Message List
Error Messages
FRU/Action in Sequence
Struck Key
See “Keyboard or Auxiliary Input Device Check” on page 63
System CMOS checksum bad - Default
configuration used
RTC battery
Real time clock error
Run BIOS Setup Utility to reconfigure system, then reboot system.
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Main board
Previous boot incomplete - Default configuration
used
“Load Default Settings” in BIOS Setup Utility.
RTC battery
Main baord
Invalid System Configuration Data
“Load Default Settings” in BIOS Setup Utility.
Main board
Operating system not found
Enter Setup and see if fixed disk and drive A are properly identified.
Dikette drive
Hard disk drive
Main board
67
Chapter 4
Error Message List
No beep Error Messages
Power-on indicator turns off and LCD is blank.
FRU/Action in Sequence
Power source (battery pack and power adapter.) See “Power
System Check” on page 64
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
Main board.
Power-on indicator turns on and LCD is blank.
Power source (battery pack and power adapter.) See “Power
System Check” on page 64
Reconnect the LCD connector
Hard disk drive
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and LCD is blank.
But you can see POST on an external CRT.
Reconnect the LCD connectors.
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and a blinking cursor
shown on LCD during POST.
Chapter 4
Ensure every connector is connected tightly and correctly.
Main board
68
Phoenix BIOS Beep Codes
Code
Beeps
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
07h
Disable shadow and execute code from the
ROM.
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
17h
BIOS ROM checksum
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
22h
1-3-1-3
24h
Test DRAM refresh
Test 8742 Keyboard Controller
Set ES segment register to 4 GB
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
Enable cache before system BIOS shadow
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
41h
Initialize extended memory for RomPilot.
42h
Initialize interrupt vectors
45h
46h
69
POST Routine Description
02h
POST device initialization
2-1-2-3
Check ROM copyright notice
Chapter 4
Code
Beeps
POST Routine Description
47h
Initialize I20 support
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
55h
Enable USB devices
58h
59h
2-2-3-1
Test for unexpected interrupts
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Data Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
Chapter 4
70
Code
POST Routine Description
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B1h
Inform RomPilot about the end of POST.
B2h
POST done- prepare to boot operating system
B4h
71
Beeps
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B7h
Initialize ACPI BIOS
B9h
Prepare Boot
BAh
Initialize SMBIOS
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
Chapter 4
Code
Beeps
POST Routine Description
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
CAh
Redirect Int 15h to enable remote keyboard
CBh
Redirect Int 13h to Memory Technologies
Devices such as ROM, RAM, PCMCIA, and
serial disk.
CCh
Redirect Int 10h to enable remote serial video
CDh
Re-map I/O and memory for PCMCIA
CEh
Initialize digitizer and display message.
D2h
Unknown interrupt
The following are for boot block in Flash ROM
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
Initialize System Management Mode
F4h
F5h
1
Output one beep
Clear Huge Segment
F6h
Boot to Mini DOS
F7h
Boot to Full DOS
Chapter 4
72
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
First, plug a monitor to CRT port. Next, enter BIOS utility to running
“Load Default Settings” then reboot the system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
LCD is too dark
LCD brightness cannot be adjusted
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
Unreadable LCD screen
Reconnect the LCD cable
Missing pels in characters
LCD cable
Abnormal screen
LCD
Wrong color displayed
Main board
LCD has extra horizontal or vertical lines
displayed.
Indicator-Related Symptoms
Symptom / Error
Action in Sequence
Indicator incorrectly remains off or on, but system
runs correctly
Main board
HDD/CD-ROM active indicators cannot work
HDD/CD-ROM drive
Device driver
Main board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 64.
Battery pack
AC adapter
See if the thermal module is overheat (Heat sink or fan).
Main board
The system cannot power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 64.
Battery pack
Power adapter
CPU
Main board
The system cannot power-off.
In Windows XP operating system, hold and press the power switch
for more than 4 seconds. If the system can power off, then the main
board is OK. Verify OS in the HDD.
Main board
73
Chapter 4
Power-Related Symptoms
Symptom / Error
Battery can’t be charged or discharged
Action in Sequence
See “Check the Battery Pack” on page 65.
Battery pack
Main board
System hang during POST
ODD/HDD/FDD/RAM module
Main board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
Main board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
PC Card cannot be inserted or ejected
Check if the PCMCIA slot is blocked
Main board
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot system.
RAM module
Main board
Check BIOS revision
System can power on, but you hear two long
beeps: “B--, B--” and the LCD is blank.
Reinsert DIMM
DIMM
Main board
Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound
comes from the computer.
Action in Sequence
OS volume control
Audio driver
Speaker
Main board
Internal speakers make noise or emit no sound.
Speaker
Main board
Microphone cannot work
Audio driver
Volume control in Windows XP
Main board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation mode
Action in Sequence
Power option in Windows XP
Hard disk drive
Main board
The system doesn’t enter standby mode after
closing the lid of the portable computer.
Driver of Power Option Properties
Lid close switch in upper case
Main board
Chapter 4
74
Power Management-Related Symptoms
Symptom / Error
The system doesn't resume from hibernation/
standby mode.
Action in Sequence
Connect AC adapter then check if the system resumes from
Standby/Hibernation mode.
Check if the battery is low.
Hard disk drive
Main board
The system doesn't resume from standby mode
after opening the lid of the portable computer.
LCD cover switch
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Refresh battery (continue use battery until power off, then charge
battery).
Main board
Battery pack
Main board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Main board
Peripheral-Related Symptoms
Symptom / Error
System configuration does not match the
installed devices.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Setup defaults”, then
reboot system.
Reconnect hard disk/CD-ROM drives/FDD or other peripherals.
Main board
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
Keyboard
Main board
USB does not work correctly
Main board
Print problems.
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Run printer self-test.
Printer driver
Printer cable
Printer
Main board
Parallel port device problems
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Device driver
Device cable
Device
Main board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
Main board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
Main board
75
Chapter 4
Modem/LAN-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Phone cable
Driver
Reconnect the Internal modem cable to the main board tightly.
Main board
Internal LAN does not work correctly
Lan cable
Driver
Main board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 78.
Chapter 4
76
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
77
1.
Run the diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 64):
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
Chapter 4
T
System board
T
LCD assembly
78
Chapter 5
Jumper and Connector Locations
Top View
Chapter 5
79
Bottom View
Decription
Item
80
Item
Description
CN18
Dock connector
CN1
to MDC connector
CN15
VGA connector
CN6
to TP FPC connector
CN14
RJ45+RJ11 Jack
CN8
to MIC connector
CN17, 16, 28
USB
CN9
to speaker
CN20
Mini card socket
CN7
to buletooth
CN24
DDR(dual)
CN10
MDC connector
PJ1
Battery connector
CN11
Audio connector
CN26
6 in 1 socket
SW1,SW2
Wireless/BT SW
CN27
1394 standard
LED 5,9,10
Wireless/BT LED
CN23
to RTC connector
CN5
HDD connector(PATA)
CN25
to thermal fan connector
CN5
HDD connector(SATA)
PJ2
to DC board connector
CN3
KB FPC connector
CN12
PCMCIA header
CN4
to LCD connector
CN2
to SW/BD FPC connector
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 3010
series products. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise
Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
81
Exploded Diagram
82
Chapter 6
Item List
Item
Chapter 6
Description
Q’ty
Item
Description
Q’ty
1
Top cover
1
51
E ring 5-2-0.41
2
2
Keyboard lock
2
52
RAM door protect
1
3
Function lens
1
53
RAM door gasket S1
1
4
TP button
1
54
RAM door gasket S2
4
5
4 way button
1
55
Thermal module
1
6
Front cover
1
56
CPU plate bracket
1
7
IR lens
1
57
HDD cover
1
8
Front button
1
58
HDD cover F
1
9
Charge lens
1
59
HDD bracket
1
10
VGA cap
1
60
Screw M2.5X3-I
3
11
Keyboard SP mylar
1
61
HDD bracket mylar
1
12
Touchpad
1
62
Screw M3X3.8
1
13
Cable Touchpad board
1
63
Inverter module
1
14
Top case keyboard
Gasket
2
64
Hinge bracket L
1
15
Top mylar
1
65
Hinge bracket R
1
16
Touchpad kapton
1
66
Cable ZH2 AU 12.1 W/
O CCD
1
17
Top case KB al foil
2
67
Screw M2X2.5-I
4
18
Screw M2X4-I
2
68
LCD bezel rubber
4
19
TP mylar
1
69
LCD rubber down
2
20
TP kapton
1
70
LCD bezel (AU)
1
21
Hinge cover L
1
71
LCD bezel logo
1
22
BU light mylar
1
72
Bezel mid rubber
2
23
Top sponge
1
74
Antenna
1
24
Hinge SP-L
1
75
LCD cover
1
25
Hinge SP-R
1
76
LCD cover shielding
1
26
Top case rubber
2
77
LCD pre coat cover
1
27
Function key
1
78
LCD cover protect
1
28
Hinge cover al foil
1
79
Ant cover protect
2
29
Hinge cover R
1
80
CCD front case
1
30
Power button
1
81
CCD lens
1
31
Hinge cover washer
1
82
Screw M1.6X3 I
1
32
Base case
1
83
CCD protect film
1
33
Base bezel R PCMCIA
1
84
CCD hinge
1
34
Base bezel L
1
85
Camera V-UBDOEM I
1
35
Base bezel F
1
86
CCD rear protect2
2
36
Battery button
2
87
Cable CCD assy
1
37
Battery latch L
1
88
CCD rear cover
1
38
Battery latch R
1
89
KB ZH2
1
39
Base rubber foot
4
90
CCD use label
1
40
HDD latch spring
1
91
LCD
1
41
Base protector mylar
1
92
Battery 3 cell
1
93
Battery 6 cell
1
42
Speaker assy
1
43
Audio gasket
1
83
Item List
Item
84
Description
Q’ty
44
USB mesh
1
45
Base flow mylar
1
46
Base rubber foot F
1
47
Base mesh
1
48
Screw M2X4-I
3
49
RAM door
1
50
Fixed screw M2.5
2
Item
Description
Q’ty
Chapter 6
FRU List
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
ADAPTER
ADAPTER 65W 3 PIN Delta
SADP-65KB DBRF LF
ZH2 ADPTER Delta S/P
AP.06501.010
ADAPTER 65W 3 PIN
LITE-ON PA1650-02 QY LF
ZH2 ADAPTER LITE-ON
S.P.
AP.06503.013
BATTERY SANYO LI-ION
3S2P 6CELL 4800mAH
ZH1 6-CELL BATTERY S/PSANYO
BT.00603.003
BATTERY PANASONIC LIION 3S2P 6CELL
4800mAH
ZH1 6-CELL BATTERY S/PMKE
BT.00605.001
BATTERY SANYO LI-ION
3S1P 3CELL 2000mAH
ZH1 3-CELL BATTERY S/PSANYO
BT.00303.002
BATTERY PANASONIC
CGR LI-ION 3S1P 3CELL
2000mAH
ZH1 3-CELL BATTERY S/PCGR
BT.00305.001
MODEM 56K
(MDC)FOXCONN
T60M845.02 EU
ZL8 MODEM 56K(MDC) EU
S/P
54.TAKV7.001
BLUETOOTH MODULE
(T60H928.01)
ZC1 FOX
BLUETOOTH(T60H928.01)
S/P
54.TAXV7.001
MINI PCI WIRELESS
BOARD 802.11 A/B/G
MOW2 INTEL MM872659
ZC1 W/L 3945ABG MOW2
S/P
KI.GLN01.002
MINI PCI WIRELESS
BOARD 802.11 A/B/G
MOW1 INTEL MM872612
ZC1 W/L 3945ABG MOW1
S/P
KI.GLN01.001
MINI PCI WIRELESS
BOARD 802.11 A/B/G ROW
INTEL MM874511
ZC1 W/L 3945ABG ROW S/
P
KI.GLN01.003
WIRELESS LAN BOARD
802.11BG INTEL
WM3945AGBGGEN
ZC1 W/L 3945BG S/P
KI.GLN01.005
FUNCTION BOARD (L)
ZH2 BUTTON BOARD S/P
55.TATV7.001
TOUCH PAD BOARD
ZH2 TOUCH PAD BOARD
S/P
55.TATV7.002
BATTERY
BOARD
Chapter 6
85
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
AUDIO BOARD
ZH2 AUDIO BOARD
55.TATV7.003
DC BOARD
ZH2 DC BOARD
55.TATV7.004
MODEM CABLE
ZH1 MODEM CABLE S/P
50.T74V7.001
BLUETOOTH CABLE
ZH1 BOLUETOOTH CABLE
S/P
50.T74V7.002
FFC CABLE - TP/B TO MB
ZH1 FFC TP/B-MB S/P
50.T74V7.003
FFC CABLE - FUNCTION/B
TO MB
ZH1 FFC BUTTON/B-MB S/
P
50.T74V7.004
POWER CORD AF-S
(INDIA)
ZL6A POWER CORD S/P
INDIA S.P.
27.A50V7.001
POWER CORD AU W/
LABEL (3 PIN)
ZL6A POWER CORD S/PAU S.P.
27.A50V7.003
POWER CORD SWISS 3
PIN
ZE1 POWER CORD 3P
SWISS S.P.
27.A99V7.004
POWER CORD AF (3 PIN)
ZI5 POWER CORD S/P-AF
27.T48V7.001
POWER CORD ITALIAN
3PIN
EI2 POWER CORD 3P
ITALY S.P.
27.A99V7.005
POWER CORD DANISH (3
PIN)
ET2S POWER CORD
SPARE PART-DANISH
27.A03V7.006
POWER CORD US BSMI
3PIN
ZL3E POWER CORD S/PTWN
27.A99V7.002
POWER CORD EU 1.8M
3PBLACK FM010008-010
PA2 ADP+POWER
CORD(3P 90W W/FPC)S/P
27.TATV7.001
POWER CORD US 1.8M 3P
BLACK FF0-920106
ZL3E POWER CORD S/PUS
27.TATV7.002
POWER CORD UK 1.8M
3P BLACK FP010008-013
ZC1 POWER CORD-US EU
S/P
27.TATV7.003
POWER CORD PRC 3P
Y536B30001218008
EW1 POWER CODE (CH)
ASSY (8 IN 1) S/P
27.TATV7.004
CABLE
86
Chapter 6
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
ZL6A POWER CORD S/PISR S.P.
27.TATV7.005
"UPPER CASE ASSY W/
TP , TP CABLE"
ZH2 TOP COVER ASSY S/P
60.TATV7.001
LOWER CASE ASSY W/
SPEAKER
ZH2 BASE CASE W/
PCMCIA ASSY S/P
60.TATV7.002
HINGE COVER L W/
FUCTION BUTTON
ZH1 HINGE COVER-L S/P
42.T74V7.001
HINGE COVER R W/
POWER BUTTON
ZH1 HINGE COVER-R S/P
42.T74V7.002
RAM DOOR W/SCREW
ZH2 RAM DOOR S/P
42.TATV7.001
WIRELESS ANTENNA
(81.ED415.010)EU
ZH2 WIRELESS ANTENNA
S/P
50.TATV7.001
COMBO
MODULE
EXTERNAL COMBO
MODULE PANASONIC
UJDA-770
ZH1 KME COMBO ASSY S/
P
KO.02406.014
COMBO
MODULE
EXTERNAL COMBO
MODULE LITEON SOSC2483K LF
ZH1 LITE-ON COMBO
ASSY S/P
KO.02409.014
DVD RW DRIVE
EXTERNAL DVD DUAL
MODULE LITEON SOSW833S LF
ZH1 LITE-ON DVD DUAL(DL) ASSY S/P
KU.00804.020
DVD RW DRIVE
EXTERNAL DVD DUAL
MODULE PANASONIC UJ840 LF
ZH1 KME DVD DUAL (D-L)
ASSY S/P
KU.00807.030
POWER CORD ISRAEL
1.8M 3P BLK FZ0I0008-038
L-F
CASE/COVER/BRACKET ASSEMBLY
COMMUNICATION MODULE
Chapter 6
87
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
DVD RW DRIVE
EXTERNAL DVD SUPER
MUJLTI MODULE LITEON
SSM-8515S LF
ZH2 DVD SUPER MULTI
ASSY S/P
KU.00804.026
CABLE
EXTERNAL OPTICAL
CABLE
"ZH2 CABLE ASSY ZH11394 (6P/6P,3A) S/P"
50.T74V7.101
HDD/HARD
DISK DRIVE
HDD 100G SEAGATE 2.5'
5.4K SATA 1.5G NCQ M2
ST9100824AS F/W 3.06
ZH2
HDD(100G)ST9100824AS
S/P
KH.10001.005
HDD/HARD
DISK DRIVE
"HDD 100G HGST 2.5'
SATA 1.5G
NCQMORAGA+HTS541010
G9SA00 FW:S60D,L"
ZH2
HDD(100GS)HTS541010G9
SA00 S/P
KH.10007.005
HDD/HARD
DISK DRIVE
"HDD 120G SEAGATE 2.5'
5400RPM MERCURY 2
ST9120821A F/W:3.04,LF"
ZH2 HDD(120G)
ST9120821A S/P
KH.12001.015
HDD/HARD
DISK DRIVE
"HDD 120G HGST 2.5'
5400RPM HAKONE-B F/W :
(ROHS),LF"
ZH2
HDD(80G)HTS541080G9AT
00 S/P
KH.12007.007
HDD/HARD
DISK DRIVE
HDD 120G SEAGATE 2.5'
5.4K SATA 1.5G NCQ M2
ST9120821AS F/W 3.03
ZC1 HDD SEAGATE 120G
S/P
KH.12001.016
HDD/HARD
DISK DRIVE
"HDD 120G SEAGATE 2.5""
5400RPM SATA
ST9120821AS LF
MERCURY 2 FW:3.06"
ZH2
HDD(120G)ST9120821AS
S/P
KH.12001.025
HDD/HARD
DISK DRIVE
"HDD 120G TOSHIBA 2.5""
5.4K SATAI1.5G W/NCQ
MK1234GSX LF TAURUS
FW:AH001A"
ZH2 HDD(120G)
MK1234GSX-CZK S/P
KH.12004.003
HDD/HARD
DISK DRIVE
"HDD '80G SEAGATE 2.5'
5.4K SATA 1.5G NCQ M2
ST98823AS F/W 3.06,LF"
ZH2 HDD(80G)ST98823AS
S/P
KH.08001.015
HDD/HARD
DISK DRIVE
"HDD 80G HGST 2.5' 5.4K
SATA 1.5G NCQ
MORAGA+HTS541080G9S
A00,C60D"
ZB1 HDD 80GS HGST S/P
KH.08007.015
CASE/COVER/
BRACKET
ASSEMBLY
HDD HOLDER
ZH1 HDD DOOR S/P
60.T74V7.003
KEYBOARD NORWAY
ZH2 K/B
MODULE(NORWEGIAN) S/
P
KB.T7407.016
KEYBOARD HEBREW
ZH2 K/B
MODULE(HEBREW) S/P
KB.T7407.022
KEYBOARD
PORTUGUESE
ZH2 K/B
MODULE(PORTUGUESE)
S/P
KB.T7407.010
KEYBOARD SWISS/G
ZH2 K/B MODULE(SWISS)
S/P
KB.T7407.009
KEYBOARD US
INTERNATIONAL
ZH2 K/B MODULE(UI) S/P
KB.T7407.026
KEYBOARD ARABIC
ZH2 K/B MODULE(ARABEN) S/P
KB.T7407.011
KEYBOARD
88
Chapter 6
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
KEYBOARD SPANISH
ZH2 K/B
MODULE(SPANISH) S/P
KB.T7407.001
KEYBOARD DANISH
ZH2K/B MODULE(DANISH)
S/P
KB.T7407.017
KEYBOARD CANADIAN
FRENCH
ZH2 K/B MODULE(FRACAN) S/P
KB.T7407.019
KEYBOARD JAPAN
ZH2 K/B MODULE(JAPAN)
S/P
KB.T7407.020
KEYBOARD ITALIAN
ZH2 K/B MODULE(ITALIAN)
S/P
KB.T7407.007
KEYBOARD GERMAN
ZH2 K/B
MODULE(GERMAN) S/P
KB.T7407.006
KEYBOARD FRENCH
ZH2 K/B
MODULE(FRENCH) S/P
KB.T7407.008
KEYBOARD UK
ZH2 K/B MODULE(UK) S/P
KB.T7407.005
KEYBOARD SWEDEN
ZH2 K/B
MODULE(SWEDISH) S/P
KB.T7407.013
KEYBOARD BELGIUM
ZH2 K/B
MODULE(BELGIUM) S/P
KB.T7407.012
KEYBOARD TURKISH
ZH2K/B
MODULE(TURKISH) S/P
KB.T7407.018
KEYBOARD RUSSIAN
ZH2 K/B
MODULE(RUSSIAN) S/P
KB.T7407.023
KEYBOARD BRAZILIAN
PROTUGESE
ZH2 K/B MODULE(BRAZIL)
S/P
KB.T7407.003
KEYBOARD HUNGAIAN
ZH2 K/B
MODULE(HUNGARIAN) S/P
KB.T7407.015
KEYBOARD CZECH
ZH2 K/B MODULE(CZECH)
S/P
KB.T7407.014
KEYBOARD THAI
ZH2 K/B MODULE(THAI) S/
P
KB.T7407.002
KEYBOARD GREEK
ZH2 K/B MODULE(GREEK)
S/P
KB.T7407.021
KEYBOARD CHINESE
ZH2 K/B MODULE(TAIWAN)
S/P
KB.T7407.027
KEYBOARD SLOVENIA
ZH2 K/B MODULE
SLOVENIA S/P
KB.T7407.024
KEYBOARD CHINA
ZH2 K/B MODULE(CHINA)
S/P
KEYBOARD DUTCH
ZH2 K/B MODULE(DUTCH)
S/P
KEYBOARD POLAND
ZH2 K/B
MODULE(POLAND) S/P
KEYBOARD LA
ZH2 K/B MODULE(LA) S/P
KEYBOARD KOREAN
ZH2 K/B
MODULE(KOREAN) S/P
KEYBOARD ICELAND
ZH2 K/B
MODULE(ICELAND) S/P
LCD 12.1 LCD MODULE
GLARE W/ CCD ASSY
ZH2 12.1 LCD W/
CCD(GLARE) ASSY S/P
LCD
LCD
Chapter 6
6M.TATV7.001
89
CATEGORY
90
PARTNAME
DESCRIPTION
ACER PART NO.
LCD
LCD 12.1 IN. TFT WXGA
AU B121EW01 V.3 GLARE
ZH1 12.1''WXGA AU
B121EW01 V.3 GLA S/P
LK.12105.003
LCD
LCD 12.1 IN. TFT WXGA
QDI QD12TL02-01 GLARE
ZH1 12.1''WXGA QD12TL02
QDI GLA S/P
LK.12109.002
LCD
LCD 12.1 IN. TFT WXGA
CMO N121I3-L01 GLARE
"ZH2 LCD(TFT)12.1""
N121I3-L01(GLARE) S/P"
LK.1210D.007
LCD INVERTER BOARD
ZH1 12 IN.WXGA LCD
INVERTER S/P
19.TATV7.001
LCD CABLE ASSY FOR
CCD
ZH2 CABLE ASSY AUO
WXGA S/P
50.TATV7.002
LCD BRACKET W/HINGE L
ZH2 HINGE-BKT-L (AU) S/P
33.TATV7.001
LCD BRACKET W/HINGE R
ZH2 HINGE-BKT-R(AU) S/P
33.TATV7.002
LCD COVER W/ANTENNA/
PRECOAT/CCD ASSY
ZH2 LCD COVER W/
PRECOAT/CCD ASSY S/P
60.TATV7.003
LCD BEZEL ASSY W/
LOGO FOR CCD
ZH2 LCD BEZEL ASSY S/P
60.TATV7.004
CCD MODULE
ZH2 LCD CCD FRONT
CASE ASSY S/P
57.TATV7.001
Chapter 6
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
LCD 12.1 LCD MODULE
NON-GLARE W/ CCD
ASSY
ZH2 12.1 LCD W/ CCD
(NON-GL) ASSY S/P
6M.TATV7.002
LCD 12.1 IN. TFT WXGA
AU B121EW01 V.5 NON
GLARE
"ZH2
LCD(TFT)12.1""B121EW01
V.5(WXGA) S/P"
LK.12105.004
LCD 12.1 IN. TFT WXGA
QDI QD12TL02-03 NON
GLARE
"ZH2 LCD12.1"" NO-GLE
QD12TL02 WXGA S/P"
LK.12109.001
LCD 12.1 IN. TFT WXGA
CMO N121I3-L02 NON
GLARE
"ZH2 LCD(TFT)
12.1""N121I3-L02(NON-GL)
S/P"
LK.1210D.006
BOARD
LCD INVERTER BOARD
ZH1 12 IN.WXGA LCD
INVERTER S/P
19.TATV7.001
CABLE
LCD CABLE ASSY FOR
CCD
ZH2 CABLE ASSY AUO
WXGA S/P
50.TATV7.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET W/HINGE L
ZH2 HINGE-BKT-L (AU) S/P
33.TATV7.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET W/HINGE R
ZH2 HINGE-BKT-R(AU) S/P
33.TATV7.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD COVER W/ANTENNA/
PRECOAT/CCD ASSY
ZH2 LCD COVER W/
PRECOAT/CCD ASSY S/P
60.TATV7.003
CASE/COVER/
BRACKET
ASSEMBLY
LCD BEZEL ASSY W/
LOGO FOR CCD
ZH2 LCD BEZEL ASSY S/P
60.TATV7.004
CCD MODULE
CCD MODULE
ZH2 LCD CCD FRONT
CASE ASSY S/P
57.TATV7.001
LCD
LCD MODULE 12.1 IN.
GLARE W/O CCD ASSY
ZH2 12.1 LCD W/O CCD
GLA ASSY S/P
6M.TATV7.003
LCD
LCD 12.1 IN. TFT WXGA
AU B121EW01 V.3 GLARE
ZH1 12.1''WXGA AU
B121EW01 V.3 GLA S/P
LK.12105.003
LCD
LCD 12.1 IN. TFT WXGA
QDI QD12TL02-01 GLARE
ZH1 12.1''WXGA QD12TL02
QDI GLA S/P
LK.12109.002
LCD
LCD 12.1 IN. TFT WXGA
CMO N121I3-L01 GLARE
"ZH2 LCD(TFT)12.1""
N121I3-L01(GLARE) S/P"
LK.1210D.007
BOARD
LCD INVERTER BOARD
ZH1 12 IN.WXGA LCD
INVERTER S/P
19.TATV7.001
CABLE
LCD CABLE ASSY W/O
CCD
"ZH2 LCD CABLE AU 12.1""
W/O CCD S/P"
50.TATV7.003
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET W/HINGE L
ZH2 HINGE-BKT-L (AU) S/P
33.TATV7.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET W/HINGE R
ZH2 HINGE-BKT-R(AU) S/P
33.TATV7.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD COVER W/ANTENNA
W/O CCD ASSY
ZH2 LCD COVER W/O CCD
ASSY S/P
60.TATV7.005
CASE/COVER/
BRACKET
ASSEMBLY
LCD BEZEL ASSY W/
LOGO W/O CCD
"ZH1 12"" LCD BEZEL W/
LOG S/P"
60.TATV7.006
Chapter 6
91
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
LCD
LCD MODULE 12.1 IN.
NON GLARE W/O CCD
ASSY
ZH2 12.1 LCD W/O CCD
NON-GL ASSY S/P
6M.TATV7.004
LCD
LCD 12.1 IN. TFT WXGA
AU B121EW01 V.5 NON
GLARE
"ZH2
LCD(TFT)12.1""B121EW01
V.5(WXGA) S/P"
LK.12105.004
LCD
LCD 12.1 IN. TFT WXGA
QDI QD12TL02-03 NON
GLARE
"ZH2 LCD12.1"" NO-GLE
QD12TL02 WXGA S/P"
LK.12109.001
LCD
LCD 12.1 IN. TFT WXGA
CMO N121I3-L02 NON
GLARE
"ZH2 LCD(TFT)
12.1""N121I3-L02(NON-GL)
S/P"
LK.1210D.006
BOARD
LCD INVERTER BOARD
ZH1 12 IN.WXGA LCD
INVERTER S/P
19.TATV7.001
CABLE
LCD CABLE ASSY W/O
CCD
"ZH2 LCD CABLE AU 12.1""
W/O CCD S/P"
50.TATV7.003
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET W/HINGE L
ZH2 HINGE-BKT-L (AU) S/P
33.TATV7.001
CASE/COVER/
BRACKET
ASSEMBLY
LCD BRACKET W/HINGE R
ZH2 HINGE-BKT-R(AU) S/P
33.TATV7.002
CASE/COVER/
BRACKET
ASSEMBLY
LCD COVER W/ANTENNA
W/O CCD ASSY
ZH2 LCD COVER W/O CCD
ASSY S/P
60.TATV7.005
CASE/COVER/
BRACKET
ASSEMBLY
LCD BEZEL ASSY W/
LOGO W/O CCD
"ZH1 12"" LCD BEZEL W/
LOG S/P"
60.TATV7.006
MAINBOARD SATA /T2300/
945GM/5 in 1/GLAN
"ZH2 MB
ASSY(Y2.0,SA,MC,G) S/P"
LB.TAT06.001
MAINBOARD SATA /T2400/
945GM/5 in 1/GLAN
"ZH2 MB ASSY
(Y1.67,SA,MC,G) S/P"
LB.TAT06.002
MAINBOARD SATA /T2500/
945GM/5 in 1/GLAN
"ZH2 MB
ASSY(Y1.83,SA,MC,G) S/P"
LB.TAT06.003
MAINBOARD SATA /T2600/
945GM/5 in 1/GLAN
"ZH2 MB
ASSY(Y2.16,7A,MC,G) S/P"
LB.TAT06.004
MEMORY
"MEMORY INFINEON,
DDRII 533 256M
HYS64T32000HDL-3.7-A"
ZB1 RAM DDRII5 256M INF
S/P
KN.25602.023
MEMORY
"MEMORY NANYA,
DDRII533 256MB
NT256T64UH4A1FN-37B
(PB-FREE)"
ZB1 RAM DDRII5 256M
NANYA S/P
KN.25603.029
MEMORY
"MEMORY HYNIX, DDRII
533 256MB
HYMP532S64P6-C4"
ZB1 RAM DDRII 533 256MB
HYNIX S/P
KN.2560G.006
MEMORY
"MEMORY INFINEON,
DDRII 533 512MB
HYS64T64020HDL-3.7-A
(0.11U/G)"
ZH2
RAM(512M)HYS64T64020H
DL-3.7-A S/P
KN.51202.021
MAINBOARD
MEMORY
92
Chapter 6
CATEGORY
PARTNAME
DESCRIPTION
ACER PART NO.
MEMORY
"MEMORY NANYA,
DDRII533 512MB
NT512T64UH8A1FN-37B
(PB-FREE)"
ZB1 RAM(512M)DDR2
NANYA S/P
KN.51203.023
MEMORY
"MEMORY SAMSUNG,
DDRII533 512MB
M470T6554CZ3-CD500"
ZB1 RAM DDRII533 512MB
SAMSUNG S/P
KN.5120B.015
MEMORY
"MEMORY HYNIX, DDRII
533 512MB
HYMP564S64P6-C4"
ZE1 RAM DDRII5 512MB
HY S/P
KN.5120G.005
THERMAL MODULE
ZH2 THERMAL MODULE S/
P
60.TATV7.007
SPEAKER
SPEAKER ASSY
ZH2 SPEAKER ASSY
SPB2410-ZH2-4 EU S/P
23.TATV7.001
MISCELLANEO
US W/O CCD
"LCD BEZEL RUBBER
(GAZH1003,REV3A) "
ZH2 LCD RUBER-UPPER
S/P
47.TATV7.001
MISCELLANEO
US W/O CCD
"LCD BEZEL RUBBER
(GAZH1003,REV3A) W/O
CCD"
ZH1 LCD RUBER-DWON S/
P
47.TATV7.002
MISCELLANEO
US W/CCD
"LCD BEZEL RUBBER
(GAZH2003,REV3A)"
ZH2 LCD RUBER-DWON S/
P
47.TATV7.003
MISCELLANEO
US W/O CCD
"LCD GASKET
(GBZH1011, REV3A)"
"ZH2 LCD GASKET
(GBZH1011, REV3A) S/P"
47.TATV7.004
SCREW
SCREW MS2.0X4.0
ET2S SCREW MS2.0X4.0
SPARE PART S/P
86.A03V7.018
SCREW
SCREW M2.0*2.5I(NI)(NYLOK)
EI2 SCREW M2.0*2.5I(NI)(NYLOK) KIT S/P
86.TADV7.001
SCREW
SCREW M2.0*5I(BNI)(NYLOK)D4 T0.
SCREW M2.0*5I(BNI)(NYLOK)D4 T0.
86.TATV7.001
SCREW
SCREW M2.0*7.0I(NI)(NYLOK)
SCREW M2.0*7.0I(NI)(NYLOK)
86.TATV7.002
SCREW
"SCREW M3.0*3.8(I)-NIHJ(4.6,0.3)"
"SCREW M3.0*3.8(I)-NIHJ(4.6,0.3)"
86.TATV7.003
SCREW
SCREW M2.5*6.0I(NI)(NYLOK)
SCREW M2.5*6.0I(NI)(NYLOK)
86.TATV7.004
Chapter 6
93