Ricoh AP2610N Service manual

CÓPIA NÃO CONTROLADA
G056/G058/G073/G074
SERVICE MANUAL
001048MIU
RICOH GROUP COMPANIES
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
®
®
G056/G058/G073/G074
SERVICE MANUAL
RICOH GROUP COMPANIES
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
G056/G058/G073/G074
SERVICE MANUAL
001048MIU
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
It is the reader's responsibility when discussing the information contained within this
document to maintain a level of confidentiality that is in the best interest of Ricoh
Corporation and its member companies.
NO PART OF THIS DOCUMENT MAY BE REPRODUCED IN ANY
FASHION AND DISTRIBUTED WITHOUT THE PRIOR
PERMISSION OF RICOH CORPORATION.
All product names, domain names or product illustrations, including desktop images,
used in this document are trademarks, registered trademarks or the property of their
respective companies.
They are used throughout this book in an informational or editorial fashion only and for
the benefit of such companies. No such use, or the use of any trade name, or web
site is intended to convey endorsement or other affiliation with Ricoh products.
 2002 RICOH Corporation. All rights reserved.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
WARNING
The Service Manual contains information
regarding service techniques, procedures,
processes and spare parts of office equipment
distributed by Ricoh Corporation. Users of this
manual should be either service trained or
certified by successfully completing a Ricoh
Technical Training Program.
Untrained and uncertified users utilizing
information contained in this service manual to
repair or modify Ricoh equipment risk personal
injury, damage to property or loss of warranty
protection.
RICOH CORPORATION
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
LEGEND
COMPANY
PRODUCT CODE
G056
GESTETNER
P7026
G058
P7026n
G073
P7126n
G074
P7126
LANIER
Ricoh
AP2610N
Ricoh
AP2610
RICOH
Aficio
AP2600
Aficio
AP2600N
AP2610N
SAVIN
SLP26
MLP26n
AP2610
MLP26
SLP26n
DOCUMENTATION HISTORY
REV. NO.
*
1
DATE
12/2000
3/2002
COMMENTS
Original Printing
G073/G074 Addition
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
IIMPORTANT SAFETY NOTICES
PREVENTION OF PHYSICAL INJURY
1. Before disassembling or assembling parts of the copier and peripherals,
make sure that the printer power cord is unplugged.
2. The wall outlet should be near the printer and easily accessible.
3. Note that some components of the printer and the paper tray unit are
supplied with electrical voltage even if the main power switch is turned off.
4. If any adjustment or operation check needs to be made with exterior covers
off or open while the main switch is turned on, keep hands away from
electrified or mechanically driven components.
5. The inside and the metal parts of the fusing unit become extremely hot while
the printer is operating. Be careful to avoid touching those components with
your bare hands.
HEALTH SAFETY CONDITIONS
Toner and developer are non-toxic, but if you get either of them in your eyes it
may cause temporary eye discomfort. Try to remove with eye drops or flush with
water as first aid. If unsuccessful, get medical attention.
OBSERVANCE OF ELECTRICAL SAFETY STANDARDS
The printer and its peripherals must be installed and maintained by a customer
service representative who has completed the training course on those models.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL
1. Do not incinerate toner bottles or used toner. Toner dust may ignite
suddenly when exposed to an open flame.
2. Dispose of used toner, developer, and organic photoconductors in
accordance with local regulations. (These are non-toxic supplies.)
3. Dispose of replaced parts in accordance with local regulations.
LASER SAFETY
The Center for Devices and Radiological Health (CDRH) prohibits the repair of
laser-based optical units in the field. The optical housing unit can only be repaired
in a factory or at a location with the requisite equipment. The laser subsystem is
replaceable in the field by a qualified Customer Engineer. The laser chassis is not
repairable in the field. Customer engineers are therefore directed to return all
chassis and laser subsystems to the factory or service depot when replacement of
the optical subsystem is required.
!WARNING
Use of controls, or adjustment, or performance of procedures other than
those specified in this manual may result in hazardous radiation exposure.
!WARNING
WARNING: Turn off the main switch before attempting any of the
procedures in the Laser Unit section. Laser beams can seriously damage
your eyes.
CAUTION MARKING:
G058R500.WMF
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
Trademarks
Microsoft®, Windows®, and MS-DOS® are registered trademarks of Microsoft
Corporation in the United States and other countries.
PostScript® is a registered trademark of Adobe Systems, Incorporated.
PCL® is a registered trademark of Hewlett-Packard Company.
Ethernet® is a registered trademark of Xerox Corporation.
PowerPC® is a registered trademark of International Business Machines
Corporation.
Other product names used herein are for identification purposes only and may be
trademarks of their respective companies. We disclaim any and all rights involved
with those marks.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
G056/G058
TABLE OF CONTENTS
INSTALLATION
1. INSTALLATION .......................................................................... 1-1
1.1 INSTALLATION REQUIREMENTS ...........................................................1-1
1.1.1 ENVIRONMENT ...............................................................................1-1
1.1.2 MACHINE LEVEL .............................................................................1-1
1.1.3 MACHINE SPACE REQUIREMENT.................................................1-1
1.1.4 POWER REQUIREMENTS ..............................................................1-2
1.2 MACHINE INSTALLATION .......................................................................1-2
1.3 OPTIONAL UNIT INSTALLATION.............................................................1-2
PREVENTIVE MAINTENANCE
2. PREVENTIVE MAINTENANCE................................................... 2-1
2.1 USER MAINTENANCE .............................................................................2-1
2.2 SERVICE MAINTENANCE........................................................................2-2
REPLACEMENT AND ADJUSTMENT
3. REPLACEMENT AND ADJUSTMENT........................................ 3-1
3.1 SPECIAL TOOLS ......................................................................................3-1
3.2 EXTERIOR COVERS ................................................................................3-2
3.3 LASER UNIT .............................................................................................3-3
3.3.1 CAUTION DECAL LOCATIONS .......................................................3-3
3.3.2 POLYGON MIRROR MOTOR ..........................................................3-4
3.3.3 LASER SYNCHRONIZATION DETECTOR......................................3-4
3.3.4 LASER UNIT ....................................................................................3-5
3.3.5 LASER DIODE UNIT ........................................................................3-7
Laser beam pitch adjustment................................................................3-8
3.4 TRANSFER ROLLER................................................................................3-9
3.5 TONER END SENSOR .............................................................................3-9
3.6 FUSING ...................................................................................................3-10
3.6.1 FUSING UNIT.................................................................................3-10
3.6.2 HOT ROLLER AND FUSING LAMP ...............................................3-11
3.6.3 THERMISTOR AND THERMOSTAT..............................................3-13
3.7 PAPER FEED..........................................................................................3-14
3.7.1 FEED ROLLER...............................................................................3-14
3.7.2 FRICTION PAD ..............................................................................3-14
3.8 BY-PASS TRAY ......................................................................................3-15
3.8.1 BY-PASS TRAY UNIT AND BY-PASS FEED ROLLER .................3-15
3.9 PRINTER CONTROLLER BOARD..........................................................3-16
3.10 ENGINE BOARD ...................................................................................3-16
SM
i
CÓPIA NÃO CONTROLADA
G056/G058/G073/G074
CÓPIA NÃO CONTROLADA
Rev. 10/2003
3.11 MAIN MOTOR .......................................................................................3-17
3.12 SOLENOIDS AND CLUTCHES.............................................................3-17
3.13 POWER SUPPLY UNIT AND HIGH VOLTAGE SUPPLY BOARD .......3-18
3.14 IMAGE ADJUSTMENT ..........................................................................3-19
3.14.1 REGISTRATION ADJUSTMENT..................................................3-19
3.14.2 PARALLELOGRAM IMAGE ADJUSTMENT ................................3-19
TROUBLESHOOTING
4. TROUBLESHOOTING ................................................................. 4-1
4.1 SERVICE CALL CONDITIONS .................................................................4-1
4.1.1 SUMMARY .......................................................................................4-1
4.1.2 SC CODE DESCRIPTIONS .............................................................4-2
4.2 CONTROLLER ERROR ............................................................................4-4
4.3 ELECTRICAL COMPONENT DEFECTS ..................................................4-6
4.3.1 SENSORS ........................................................................................4-6
4.3.2 SWITCHES.......................................................................................4-6
4.4 BLOWN FUSE CONDITIONS ...................................................................4-7
4.5 LEDS .........................................................................................................4-7
SERVICE TABLES
5. SERVICE TABLES....................................................................... 5-1
5.1 SERVICE PROGRAM MODE....................................................................5-1
5.1.1 ENABLING AND DISABLING SERVICE PROGRAM MODE ...........5-1
Entering the Service Mode....................................................................5-1
Accessing the Required Program .........................................................5-1
Inputting a Value or Setting for a Service Program ...............................5-2
Exiting Service Mode ............................................................................5-2
5.2 PRINTER CONTROLLER SERVICE MODE .............................................5-2
5.2.1 SERVICE MODE MENU (‘1. SERVICE MENU’) .........................5-2
5.2.2 BIT SWITCH PROGRAMMING ........................................................5-2
5.3 PRINTER ENGINE SERVICE MODE........................................................5-4
5.3.1 SERVICE MODE TABLE (‘2. ENGINE MAINTE’) .......................5-4
Memory Clear .......................................................................................5-8
5.3.2 INPUT CHECK TABLE ...................................................................5-10
Table 1: Paper Size Switch (Main Unit) ..............................................5-11
Table 2: Paper Size Switch (optional paper tray)................................5-12
Table 3: Paper Height Sensor (standard cassette) .............................5-12
Table 4: Paper Height Sensor (optional paper tray)............................5-12
5.3.3 OUTPUT CHECK TABLE ...............................................................5-13
5.4 FIRMWARE UPDATE PROCEDURE......................................................5-14
5.4.1 CONTROLLER/NIB/ENGINE FIRMWARE UPDATE......................5-14
5.4.2 ERROR RECOVERY......................................................................5-15
Controller ............................................................................................5-15
NIB/Engine Board ...............................................................................5-15
G056/G058/G073/G074
ii
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Rev. 10/2003
5.5
5.6
5.7
5.8
POWER-ON SELF TEST ........................................................................5-16
OTHER TESTS .......................................................................................5-16
USER PROGRAM MODE .......................................................................5-17
DIP SWITCHES.......................................................................................5-18
Controller Board..................................................................................5-18
Engine Board ......................................................................................5-18
DETAILED DESCRIPTIONS
6. DETAILED SECTION DESCRIPTIONS ....................................... 6-1
6.1 OVERVIEW ...............................................................................................6-1
6.1.1 MECHANICAL COMPONENT LAYOUT...........................................6-1
6.1.2 PAPER PATH ...................................................................................6-2
6.2 BOARD STRUCTURE...............................................................................6-3
6.2.1 OVERVIEW ......................................................................................6-3
6.2.2 DESCRIPTIONS...............................................................................6-4
6.2.3 CONTROLLER BOARD ...................................................................6-5
6.3 PRINTING PROCESS ...............................................................................6-6
6.3.1 OVERVIEW ......................................................................................6-6
6.3.2 LASER EXPOSURE .........................................................................6-7
Overview...............................................................................................6-7
Automatic Power Control (APC) ...........................................................6-8
LD Safety Mechanisms .........................................................................6-9
6.3.3 CARTRIDGE OVERVIEW ..............................................................6-10
6.3.4 DRUM CHARGE.............................................................................6-10
6.3.5 DEVELOPMENT.............................................................................6-11
Overview.............................................................................................6-11
Toner Supply ......................................................................................6-11
Development Unit ...............................................................................6-11
Toner Density Control .........................................................................6-12
Development Bias...............................................................................6-12
Toner End Detection ...........................................................................6-13
6.3.6 IMAGE TRANSFER AND PAPER SEPARATION ..........................6-14
Overview.............................................................................................6-14
Transfer Roller Cleaning .....................................................................6-14
6.3.7 CLEANING .....................................................................................6-15
6.3.8 QUENCHING..................................................................................6-15
6.3.9 ID CHIP ..........................................................................................6-16
6.4 PAPER FEED..........................................................................................6-17
6.4.1 OVERVIEW ....................................................................................6-17
Paper Tray ..........................................................................................6-17
By-pass Tray.......................................................................................6-17
6.4.2 PAPER TRAY .................................................................................6-18
Tray Extension ....................................................................................6-18
SM
iii
CÓPIA NÃO CONTROLADA
G056/G058/G073/G074
CÓPIA NÃO CONTROLADA
Paper Lift ............................................................................................6-18
Paper Feed and Registration ..............................................................6-19
Paper Size Detection ..........................................................................6-20
Paper End/Paper Near-end Detection ................................................6-20
6.4.3 BY-PASS TRAY..............................................................................6-21
6.5 IMAGE FUSING AND PAPER EXIT........................................................6-22
6.5.1 OVERVIEW ....................................................................................6-22
6.5.2 FUSING DRIVE ..............................................................................6-22
6.5.3 FUSING ENTRANCE GUIDE SHIFT..............................................6-23
6.5.4 PRESSURE ROLLER.....................................................................6-23
6.5.5 NEW FUSING UNIT DETECTION..................................................6-24
6.5.6 FUSING TEMPERATURE CONTROL............................................6-25
6.5.7 PAPER EXIT ..................................................................................6-26
6.5.8 ENERGY SAVER MODE................................................................6-27
Entering Energy Saver Mode..............................................................6-27
Leaving Energy Saver Mode...............................................................6-27
6.6 CONTROLLER FUNCTIONS ..................................................................6-28
6.6.1 METER-CHARGE MODE...............................................................6-28
Meter-charge Counter Display ............................................................6-28
PM Warning Display ...........................................................................6-28
6.6.2 SAMPLE PRINT .............................................................................6-28
6.6.3 LOCKED PRINT .............................................................................6-29
6.6.4 PAPER SOURCE SELECTION......................................................6-29
Tray Priority (Auto Tray Select)...........................................................6-29
Tray Lock ............................................................................................6-29
Manual Tray Select .............................................................................6-29
6.6.5 AUTO CONTINUE ..........................................................................6-30
Auto Tray Select .................................................................................6-30
Manual Tray Select .............................................................................6-30
6.6.6 PAPER OUTPUT TRAY .................................................................6-31
Output Tray Selected ..........................................................................6-31
Auto Tray Switching ............................................................................6-31
6.7 NIB ..........................................................................................................6-32
6.7.1 BLOCK DIAGRAM..........................................................................6-32
6.7.2 LED INDICATORS..........................................................................6-32
6.8 IEEE1394 INTERFACE ...........................................................................6-33
6.8.1 SPECIFICATIONS..........................................................................6-33
Hardware Specification .......................................................................6-33
System Requirements.........................................................................6-33
6.8.2 IEEE1394 .......................................................................................6-33
6.8.3 BLOCK DIAGRAM..........................................................................6-34
6.8.4 PIN ASSIGNMENT .........................................................................6-34
6.8.5 REMARKS ABOUT THIS INTERFACE KIT....................................6-35
6.8.6 TROUBLESHOOTING NOTES ......................................................6-35
G056/G058/G073/G074
iv
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
7. SPECIFICATIONS....................................................................... 7-1
7.1. GENERAL SPECIFICATIONS..................................................................7-1
7.1.1 SUPPORTED PAPER SIZES...........................................................7-3
7.2. SOFTWARE ACCESSORIES ..................................................................7-4
7.2.1 PRINTER DRIVERS .........................................................................7-4
7.2.2 UTILITY SOFTWARE .......................................................................7-4
7.3. MACHINE CONFIGURATION ..................................................................7-5
7.3.1 SYSTEM COMPONENTS ................................................................7-5
7.4. OPTIONAL EQUIPMENT .........................................................................7-6
7.4.1 PAPER TRAY UNIT..........................................................................7-6
7.4.2 ENVELOPE FEEDER.......................................................................7-6
7.4.3 DUPLEX UNIT ..................................................................................7-6
7.4.4 FOUR-BIN MAILBOX .......................................................................7-7
7.4.5 ONE-BIN SHIFT TRAY.....................................................................7-7
PAPER TRAY UNIT G555/ENVELOPE FEEDER G556
1. REPLACEMENT AND ADJUSTMENT........................................ 8-1
1.1 PAPER FEED UNIT ..................................................................................8-1
1.2 PAPER FEED ROLLER ............................................................................8-2
1.3 FRICTION PAD .........................................................................................8-2
2. DETAILED DESCRIPTIONS ....................................................... 8-3
2.1 OVERALL MACHINE INFORMATION ......................................................8-3
2.1.1 MECHANICAL COMPONENT LAYOUT...........................................8-3
2.1.2 ELECTRICAL COMPONENT LAYOUT ............................................8-3
2.2 DETAILED SECTION DESCRIPTIONS ....................................................8-4
2.2.1 PAPER FEED AND SEPARATION ..................................................8-4
2.2.2 PAPER LIFT .....................................................................................8-5
2.2.3 PAPER END DETECTION ...............................................................8-5
2.2.4 PAPER HEIGHT DETECTION .........................................................8-6
2.2.5 PAPER SIZE DETECTION...............................................................8-7
3. ENVELOPE FEEDER.................................................................. 8-8
3.1 OVERALL MACHINE INFORMATION ......................................................8-8
3.1.1 MECHANICAL COMPONENT LAYOUT...........................................8-8
DUPLEX UNIT G552
1. REPLACEMENT AND ADJUSTMENT........................................ 9-1
1.1 EXTERIOR COVERS ................................................................................9-1
1.2 DUPLEX BOARD AND SENSORS ...........................................................9-2
SM
v
CÓPIA NÃO CONTROLADA
G056/G058/G073/G074
CÓPIA NÃO CONTROLADA
2. DETAILED DESCRIPTION ......................................................... 9-3
2.1 OVERALL MACHINE INFORMATION ......................................................9-3
2.1.1 MECHANICAL COMPONENT LAYOUT...........................................9-3
2.1.2 DRIVE LAYOUT ...............................................................................9-4
2.1.3 ELECTRICAL COMPONENT LAYOUT ............................................9-4
2.2 DETAILED SECTION DESCRIPTIONS ....................................................9-5
2.2.1 BASIC OPERATION.........................................................................9-5
Longer than A4 LEF/LT LEF .................................................................9-5
Length up to A4 LEF/LT LEF ................................................................9-6
2.2.2 FEED IN AND EXIT MECHANISM ...................................................9-7
Feeding paper into the duplex unit:.......................................................9-7
Inversion and exit:.................................................................................9-7
FOUR-BIN MAILBOX G553
1. REPLACEMENT AND ADJUSTMENT...................................... 10-1
1.1 EXTERIOR COVERS ..............................................................................10-1
1.2 OVERFLOW AND VERTICAL TRANSPORT SENSORS .......................10-2
1.3 MAIN MOTOR .........................................................................................10-3
2. DETAILED DESCRIPTIONS ..................................................... 10-5
2.1 OVERALL MACHINE INFORMATION ....................................................10-5
2.1.1 MECHANICAL COMPONENT LAYOUT.........................................10-5
2.1.2 DRIVE LAYOUT .............................................................................10-6
2.1.3 ELECTRICAL COMPONENT LAYOUT ..........................................10-7
2.2 DETAILED SECTION DESCRIPTIONS ..................................................10-8
2.2.1 BASIC OPERATION.......................................................................10-8
ONE-BIN SHIFT TRAY G554
1. REPLACEMENT AND ADJUSTMENT...................................... 11-1
1.1
1.2
1.3
1.4
EXTERIOR COVERS ..............................................................................11-1
SHIFT TIMING AND TRAY PAPER SENSORS ......................................11-2
COVER AND OVERFLOW SENSORS ...................................................11-2
MAIN MOTOR .........................................................................................11-3
2. DETAILED DESCRIPTIONS ..................................................... 11-5
2.1 OVERALL MACHINE INFORMATION ....................................................11-5
2.1.1 MECHANICAL COMPONENT LAYOUT.........................................11-5
2.1.2 DRIVE LAYOUT .............................................................................11-5
2.1.3 ELECTRICAL COMPONENT LAYOUT ..........................................11-6
2.2 DETAILED SECTION DESCRIPTIONS ..................................................11-7
2.2.1 BASIC OPERATION.......................................................................11-7
2.2.2 SORT MODE OPERATION............................................................11-7
G056/G058/G073/G074
vi
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SWAPBOX
 AND SWAPFTL
 INSTALLATION MANUAL
1. INTRODUCTION ...................................................................... 12-1
1.1 PRECAUTIONS........................................................................................12-1
1.1.1 SWAPBOX AND SOFTWARE ........................................................12-1
1.1.2 SOFTWARE LICENSE AGREEMENT ...........................................12-1
1.2 SYSTEM REQUIREMENTS ....................................................................12-1
1.3 ITEMS TO PREPARE BEFORE INSTALLATION ...................................12-1
1.4 WINDOWS 95 VERSION CONFIRMATION ............................................12-2
2. SWAPBOX INSTALLATION ..................................................... 12-4
2.2 DRIVER INSTALLATION ........................................................................12-4
3. SOFTWARE (SWAPFTL) INSTALLATION ............................... 12-5
3.1 SWAPFTL SOFTWARE INSTALLATION ................................................12-5
3.2 VERIFICATION ...................................................................................... 12-5
3.2.1 SOFTWARE VERSION ..................................................................12-5
3.2.2 FLASH MEMORY CARD AUTOMATIC DETECTION ....................12-6
4. TROUBLESHOOTING ............................................................... 12-7
4.1 SWAPBOX RESOURCE CONFLICT ......................................................12-7
4.11 IRQ AND I/O ADDRESS ..................................................................12-7
4.1.2 MEMORY ADDRESS ......................................................................12-7
4.2 FAILED TO OPEN PCCARD ERRORS ...................................................12-8
4.2.1 TIMELAG TO LOADING DRIVER ...................................................12-8
4.2.3 RESOURCE CONFLICT .................................................................12-8
4.3 INVALID DYNAMIC LINK CALL FROM SWAPENUM ERROR...............12-9
4.4 SWAPFTL PROBLEM WITH NOTEBOOK COMPUTERS.......................12-9
4.4.1 WINDOWS AND PC CARD DRIVER VERSION .............................12-9
4.4.2 SYSTEM SUMMERY.......................................................................12-9
4.5 COMPLETE UNINSTALL .......................................................................12-10
SWAPFTL
 BINARY UTILITY OPERATION MANUAL
1. OVERVIEW ................................................................................ 13-1
2. OPERATION .............................................................................. 13-2
2.1 PROGRAMMING A FLASH MEMORY CARD..........................................13-2
2.1.1 GETTING A SOURCE FILE ............................................................13-2
2.1.2 PROGRAMMING A CARD WITH THE SOURCE............................13-2
2.2 DOWNLOADING TO A MACHINE ...........................................................13-4
2.3 SAVING DATA TO A FILE .......................................................................13-4
3. FUNCTIONS............................................................................... 13-5
3.1 FILE MENU ..............................................................................................13-5
3.1.1 FILE – OPEN...................................................................................13-5
SM
vii
CÓPIA NÃO CONTROLADA
G056/G058/G073/G074
CÓPIA NÃO CONTROLADA
3.1.2 FILE – CLOSE.................................................................................13-5
3.1.3 FILE – SAVE ...................................................................................13-5
3.14 FILE – SAVE AS...............................................................................13-6
3.2 VIEW MENU.............................................................................................13-6
3.2.1 VIEW – TOOLBAR ..........................................................................13-6
3.2.2 VIEW – STATUS BAR .....................................................................13-6
3.3 IMAGE MENU ..........................................................................................13-7
3.3.1 IMAGE – ERASE .............................................................................13-7
3.3.2 IMAGE – READ ...............................................................................13-8
3.3.3 IMAGE – WRITE .............................................................................13-9
3.3.4 IMAGE – VERIFICATION ..............................................................13-10
3.4 HELP MUNU ..........................................................................................13-11
3.4.1 HELP – ABOUT SWAPUTI............................................................13-11
G056/G058/G073/G074
viii
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Rev. 12/2002
G073/G074
TABLE OF CONTENTS
INSTALLATION
1. INSTALLATION............................................................................ 1-1
1.1 OPTIONAL UNIT INSTALLATION.............................................................1-1
PREVENTIVE MAINTENANCE
2. PREVENTIVE MAINTENANCE.................................................... 2-1
2.1 USER/SERVICE MAINTENANCE .............................................................2-1
REPLACEMENT AND ADJUSTMENT
3. REPLACEMENT AND ADJUSTMENT ........................................ 3-1
3.1 DIFFERENCES FROM THE MODEL K-P1 ...............................................3-1
TROUBLESHOOTING
4. TROUBLESHOOTING ................................................................. 4-1
4.1 SERVICE CALL CONDITIONS .................................................................4-1
4.1.1 SUMMARY .......................................................................................4-1
4.1.2 CONTROLLER SC CODE DESCRIPTIONS ....................................4-2
4.2 JAM LOCATIONS......................................................................................4-6
4.3 FIRMWARE HISTORY ..............................................................................4-7
4.3.1 PRINTER ENGINE FIRMWARE HISTORY ......................................4-7
4.3.2 PRINTER CONTROLLER FIRMWARE HISTORY ...........................4-8
SERVICE TABLES
5. SP MODE TABLES ...................................................................... 5-1
5.1 PRINTER CONTROLLER SERVICE MODE .............................................5-1
5.1.1 SERVICE MODE MENU (“1. SERVICE MENU”) .........................5-1
5.1.2 BIT SWITCH PROGRAMMING ........................................................5-2
5.2 PRINTER ENGINE SERVICE MODE........................................................5-3
5.2.1 SERVICE MODE TABLE (“2. ENGINE MAINTE”) .......................5-3
5.2.2 INPUT / OUTPUT CHECK TABLE ...................................................5-8
5.3 USER PROGRAM MODE .........................................................................5-9
SM
i
CÓPIA NÃO CONTROLADA
G056/G058/G073/G074
CÓPIA NÃO CONTROLADA
DETAILED DESCRIPTIONS
6. DETAILED SECTION DESCRIPTIONS ...................................... 6-1
6.1 CONTROLLER BOARD ............................................................................6-1
6.2 USB ...........................................................................................................6-2
6.2.1 SPECIFICATIONS............................................................................6-2
6.2.2 USB 1.1/2.0 ......................................................................................6-2
6.2.3 USB CONNECTORS........................................................................6-3
6.2.4 PIN ASSIGNMENT ...........................................................................6-3
6.2.5 REMARKS ........................................................................................6-4
Related SP Mode..................................................................................6-4
6.3 IEEE802.11B (WIRELESS LAN) ...............................................................6-5
6.3.1 SPECIFICATIONS............................................................................6-5
6.3.2 BLOCK DIAGRAM............................................................................6-5
6.3.3 TRANSMISSION MODE...................................................................6-6
Ad hoc Mode.........................................................................................6-6
Infrastructure Mode...............................................................................6-6
6.3.4 SECURITY FEATURES ...................................................................6-7
Using the SSID in Ad hoc mode............................................................6-7
6.3.5 TROUBLESHOOTING NOTES ........................................................6-8
Communication Status..........................................................................6-8
Channel Settings...................................................................................6-8
Troubleshooting Steps ..........................................................................6-9
6.4 NEW FEATURES ....................................................................................6-10
6.4.1 IP OVER 1394 ................................................................................6-10
6.4.2 JOB SPOOLING .............................................................................6-11
Description ..........................................................................................6-11
Related SP Modes ..............................................................................6-11
SPECIFICATIONS
7. SPECIFICATIONS
1. GENERAL SPECIFICATIONS.....................................................................7-1
1.1 SUPPORTED PAPER SIZES ..............................................................7-3
2. SOFTWARE ACCESSORIES .....................................................................7-4
2.1 PRINTER DRIVERS ............................................................................7-4
2.2 UTILITY SOFTWARE ..........................................................................7-4
3. MACHINE CONFIGURATION ......................................................................7-5
3.1 SYSTEM COMPONENTS ...................................................................7-5
3.2 INTERNAL OPTIONS..........................................................................7-6
4. OPTIONAL EQUIPMENT .............................................................................7-7
G056/G058/G073/G074
ii
CÓPIA NÃO CONTROLADA
SM
REPLACEMENT AND ADJUSTMENT B056/B058
ONE-BIN SHIFT TRAY G554
REPLACEMENT AND ADJUSTMENT
G073/G074T
TROUBLESHOOTING B056/B058
SWAPBOXTM AND SWAPFTLTM INSTALLATION MANUAL
TROUBLESHOOTING G073/G074
SERVICE TABLES B056/B058
SWAPFTLTM BINARY UTILITY OPERATION MANUAL
SERVICE TABLES G073/G074
DETAILED DESCRIPTIONS B056/B058
DETAILED DESCRIPTIONS G073/G074
SPECIFICATIONS B056/B058
SPECIFICATIONS G073/G074
PAPER TRAY G555/ENVELOPE FEEDER G556
CÓPIA NÃO CONTROLADA
TAB
POSITION 2
TAB
POSITION 3
PREVENTIVE MAINTENANCE
G073/G074
TAB
POSITION 4
FOUR-BIN MAILBOX G553
TAB
POSITION 5
PREVENTIVE MAINTENANCE B056/B058
TAB
POSITION 6
INSTALLATION G073/G074
TAB
POSITION 7
DUPLEX UNIT G552
TAB
POSITION 8
INSTALLATION B056/B058
TAB
POSITION 1
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
INSTALLATION
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
INSTALLATION REQUIREMENTS
Installation
1. INSTALLATION
1.1 INSTALLATION REQUIREMENTS
1.1.1 ENVIRONMENT
1. Temperature Range:
10 °C to 32 °C (50 °F to 89.6 °F)
2. Humidity Range:
15 % to 80 % RH
3. Ambient Illumination:
Less than 2,000 lux (do not expose to direct sunlight).
4. Ventilation:
3 times/hr/person
5. Avoid areas which are exposed to sudden temperature changes. This includes:
1) Areas directly exposed to cool air from an air conditioner.
2) Areas directly exposed to heat from a heater.
6. Do not place the machine in an area where it will be exposed to corrosive
gases.
7. Do not install the machine at any location over 2,500 m (8,125 ft.) above sea
level.
8. Place the machine on a strong and level base. (Inclination on any side should
be no more than 5 mm.)
9. Do not place the machine where it may be subjected to strong vibrations.
1.1.2 MACHINE LEVEL
Front to back:
Within 5 mm (0.2”) of level
Right to left:
Within 5 mm (0.2”) of level
1.1.3 MACHINE SPACE REQUIREMENT
Place the machine near the power source, providing clearance as shown.
A: Over 10 cm (4”)
B
B: Over 10 cm (4”)
C: Over 100 cm (40”)
C
A
D: Over 10 cm (4”)
D
G056I500.WMF
SM
1-1
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
MACHINE INSTALLATION
1.1.4 POWER REQUIREMENTS
!CAUTION
1. Make sure the plug is firmly inserted in the outlet.
2. Avoid multi-wiring.
3. Be sure to ground the machine.
1. Input voltage level: 120 V, 60 Hz: More than 10 A
220 V ~ 240 V, 50 Hz/60 Hz: More than 6 A
2. Permissible voltage fluctuation: ±10 %
3. Do not set anything on the power cord.
1.2 MACHINE INSTALLATION
Refer to the Operating Instructions for details.
1.3 OPTIONAL UNIT INSTALLATION
The following options are available for this machine. Refer to the Operating
Instructions for how to install these options.
• Paper Tray Unit
• 4-bin Mailbox
• 1-bin Shift Tray
• Duplex Unit
• Envelope Feeder
• NIB (G056 only) - the NIB is a standard component for the G058
• Hard disk
• IEEE1394 (G056/G058 - to install in the G058, the NIB must be removed first)
• 64-MB DIMM
G056/G058
1-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PREVENTIVE MAINTENANCE
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
USER MAINTENANCE
2. PREVENTIVE MAINTENANCE
2.1 USER MAINTENANCE
Meter-charge mode must be set to 'disabled' (controller service mode).
Cross-reference: Section 5.3 Engine service mode
When the PM counter reaches 90K, "Replace Maintenance Kit" is displayed. After
the user replaces the fusing unit in the maintenance kit, the machine automatically
resets the PM counter.
Item
Fusing unit
Transfer roller
Paper feed roller for the standard tray
Paper feed rollers for the optional
PFU
Friction pad - standard tray
Friction pads - optional trays
SM
Quantity
1
1
1
2
1
2
Remarks
Optional paper tray unit
Optional paper tray unit
2-1
CÓPIA NÃO CONTROLADA
G056/G058
Preventive
Maintenance
All PM items can be done by the customer, using the maintenance kit. The
maintenance kit contains the items listed below.
CÓPIA NÃO CONTROLADA
SERVICE MAINTENANCE
2.2 SERVICE MAINTENANCE
The following tables list the PM items when the PM is done by service.
NOTE: 1) You must switch on meter-charge mode in printer engine service mode
to disable the user's PM warning.
2) After replacing the fusing unit, make sure to reset the PM counter using
the printer engine service mode “PM Counter Reset”.
Symbol key: C: Clean, R: Replace, L: Lubricate, I: Inspect
Main unit
Item
Paper Feed
Paper Feed Roller
Friction Pad
Registration Mylar
Around the Drum
Transfer Roller
Fusing Unit and Paper Exit
Hot Roller
Pressure Roller
Hot Roller Strippers
Fusing Thermistor
Bushing - Fusing Roller
Bushing - Fusing Pressure
Fusing Entrance and Exit Guide
Plates
90K
EM
Remarks
R
R
C
C
C
C
Clean with water
Clean with water
Clean with water
C
Clean with alcohol if necessary.
R
R
R
R
R
R
R
Clean with water or alcohol
C
Paper Tray Unit
Paper Feed Roller
Friction Pad
Bottom Plate Pad
90K
R
R
C
EM
C
C
C
NOTE
Clean with water
Dry cloth
Clean with water
90K
EM
C
C
C
NOTE
Clean with water
Clean with water
Clean with water
90K
EM
C
C
C
C
C
NOTE
Clean with water
Clean with water
Clean with water
Clean with water
Clean with water
Four-bin Mailbox
Exit Rollers
Driven Rollers
Trays
One-bin Shift Tray
Exit Rollers
Driven Rollers
Transport Rollers
Paper Tray
Tray Paper Sensor
G056/G058
2-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
REPLACEMENT AND ADJUSTMENT
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SPECIAL TOOLS
3. REPLACEMENT AND ADJUSTMENT
!CAUTION
Turn off the main power switch and unplug the machine before attempting
any of the procedures in this section.
" : Connector
3.1 SPECIAL TOOLS
Part Number
A0069104
A2309352
G0219350
SM
Description
Scanner Positioning Pin (4 pcs/set)
Flash Memory Card - 4MB
Loop-back connector - parallel
3-1
CÓPIA NÃO CONTROLADA
Described
Section
3.3
5.4
5.5
Q’ty
1
1
1
G056/G058
Replacement
and
Adjustment
NOTE: This manual uses the following symbols.
☛ : See or Refer to
! : Screws
CÓPIA NÃO CONTROLADA
EXTERIOR COVERS
3.2 EXTERIOR COVERS
[D]
[B]
[A]
[C]
[E]
G058R701.WMF
G058R201.WMF
[H]
[F]
[G]
G058R703.WMF
G058R702.WMF
To remove the left or right cover, separate the machine from the optional paper
tray unit first.
Open the front cover.
[A]: Remove paper tray
[B]: Operation panel (2 hooks, " x1)
[C]: Upper exit cover
[D]: Open the exit guide plate.
[E]: Upper cover (! x4)
[F]: By-pass tray unit (2 hooks)
[G]: Front cover (3 hooks, " x1)
[H]: Left cover (! x2)
[I]: Right cover (3 hooks)
G056/G058
3-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
LASER UNIT
3.3 LASER UNIT
!WARNING
Turn off the main power switch and unplug the machine before attempting
any of the procedures in this section. Laser beams can seriously damage
your eyes.
3.3.1 CAUTION DECAL LOCATIONS
Replacement
and
Adjustment
The caution decal is located in the laser section as shown below.
G058R500.WMF
G058R202.WMF
SM
3-3
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
LASER UNIT
3.3.2 POLYGON MIRROR MOTOR
!WARNING
Turn off the main switch and unplug the machine before attempting any of
the procedures in this section. Laser beams can seriously damage your
eyes.
Operation panel (☛ 3.2 Exterior
Covers)
[B]
[A]
Upper cover (☛ 3.2 Exterior Covers)
[A]: Polygon mirror cover (! x2)
[B]: Polygon mirror motor
(! x4, " x1)
NOTE: Do not touch the surface of the
mirror with bare hands.
G058R204.WMF
3.3.3 LASER SYNCHRONIZATION DETECTOR
Operation panel (☛ 3.2 Exterior Covers)
Upper cover (☛ 3.2 Exterior Covers)
[A]: Laser synchronization detector (" x1)
[A]
G058R206.WMF
G056/G058
3-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
LASER UNIT
3.3.4 LASER UNIT
Replacement
and
Adjustment
[A]
G058R730.WMF
[D]
[C]
[B]
G058R203.WMF
Operation panel (☛ 3.2 Exterior Covers)
Upper cover (☛ 3.2 Exterior Covers)
Left cover (☛ 3.2 Exterior Covers)
[A]: 230V machine only: Sheet (! x1)
[B]: Thermistor (! x1)
[C]: Clip
[D]: Laser unit (! x4, 1 flat cable, " x2)
SM
3-5
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
LASER UNIT
When reinstalling the laser unit
Use the scanner positioning pin (P/N: A0069104) to reinstall the unit.
[E]
G058R208.WMF
[E]: Set the positioning pins as shown above. Then secure the laser unit.
G056/G058
3-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
LASER UNIT
Rev. 08/2001
3.3.5 LASER DIODE UNIT
⇒
[C]
Replacement
and
Adjustment
[A]
[F]
[B]
[D]
[E]
G058R209.WMF
Laser Unit (☛ 3.3.4 Laser Unit)
[A]: Spring
[B]: LD unit holders
[C]: Loosen the screw
[D]: Nut
[E]: LD Unit
NOTE: 1) Do not remove the screws that secure the LD board.
2) Do not touch any variable resistors on the LD board.
When installing the LD Unit:
Tighten the screw [C] until the unpainted portion of the screw [F] is not visible.
After installing the LD unit, check the test pattern for the final adjustment (see
Laser beam pitch adjustment the following procedure).
SM
3-7
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
LASER UNIT
Laser beam pitch adjustment
1. Print out the following test patterns – cross-stitch pattern and grid pattern.
2. Check these test patterns. If the laser beam pitch is not correct, the images are
as follows.
• Cross-stitch pattern: Vertical black strips seem to appear.
• Grid pattern: The density of the diagonal lines is light or the lines have
disappeared.
3. Adjust the LD unit holder position: Tighten or loosen the screw [C] (see the
previous page) until the printout appears as follows.
• Cross-stitch pattern: The thin lines are of uniform thickness (no striping
effect should appear on the printout).
• Grid pattern: The diagonal lines appear clearly and are of normal density.
Feed direction
G056R502.WMF
Adjustment not complete
G056/G058
Adjustment complete
3-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
TRANSFER ROLLER
3.4 TRANSFER ROLLER
[A]
G058R401.WMF
3.5 TONER END SENSOR
Cartridge
[A]: Toner end sensor (4 hooks, " x1)
[A]
SM
3-9
CÓPIA NÃO CONTROLADA
G058R301.WMF
G056/G058
Replacement
and
Adjustment
Cartridge
[A]: Transfer roller
NOTE: Do not touch the transfer
roller surface.
CÓPIA NÃO CONTROLADA
FUSING
3.6 FUSING
3.6.1 FUSING UNIT
!CAUTION
Allow time for the unit to cool before doing the following procedure.
[A]
G058R501.WMF
[C]
[C]
[B]
G058R502.WMF
[A]: Exit cover
[B]: Fusing unit (lift hooks [C])
G056/G058
3-10
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
FUSING
3.6.2 HOT ROLLER AND FUSING LAMP
[A]
Replacement
and
Adjustment
[B]
G058R508.WMF
[D]
[C]
[D]
G058R507.WMF
Fusing unit (☛ 3.6.1 Fusing Unit)
[A]: Right cover (! x2)
[B]: Upper fusing unit assembly (! x4)
[C]: Left cover (! x1)
[D]: Lamp holders (! x1 each)
SM
3-11
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
FUSING
[E]
[F]
G058R506.WMF
[H]
G058R510.WMF
[G]
G058R505.WMF
[E]: Fusing lamp (! x2)
NOTE: The shorter cable must be at the hot roller gear side.
[F]: Guide plate (3 hooks)
[G]: Hot roller strippers (1 spring each)
[H]: Hot roller (2 C-rings, 1 gear, 2 bushings).
NOTE: Before installing the new hot roller, peel off 3 cm (1 inch) from both
ends of the protective sheet on the new roller.
Remove protective sheet.
G056/G058
3-12
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
FUSING
3.6.3 THERMISTOR AND THERMOSTAT
[A]
[C]
[B]
Replacement
and
Adjustment
[D]
[E]
G058R503.WMF
Hot roller (☛ 3.6.2 Hot Roller and Fusing Lamp)
[A]: Wire cover (! x1)
[B]: Grounding plate (! x1, 1 wire)
[C]: Fusing unit connector (! x3, " x1))
[D]: Thermistor (! x1)
[E]: Thermostat (! x1)
SM
3-13
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PAPER FEED
3.7 PAPER FEED
3.7.1 FEED ROLLER
Paper Tray
[A]: Paper feed roller
[A]
G058R107.WMF
3.7.2 FRICTION PAD
[A]
Paper Tray
[A]: Friction pad (2 hooks, 1 spring)
G058R404.WMF
G056/G058
3-14
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
BY-PASS TRAY
3.8 BY-PASS TRAY
3.8.1 BY-PASS TRAY UNIT AND BY-PASS FEED ROLLER
[D]
[B]
G058R103.WMF
[C]
G058R102.WMF
By-pass tray unit (☛ 3.2 Exterior Covers)
Front cover (☛ 3.2 Exterior Covers)
Cartridge
[A]: Paper guide (! x2)
[B]: Actuator
[C]: Gear (1 hook)
[D]: By-pass feed roller
When reinstalling the paper guide:
1) Set the paper guide on the bushing.
2) Install the left part of the actuator in the machine.
3) Install the right part of the actuator on the paper guide.
4) Install the paper guide.
5) Make sure that the actuator moves smoothly.
SM
3-15
CÓPIA NÃO CONTROLADA
G056/G058
Replacement
and
Adjustment
[A]
CÓPIA NÃO CONTROLADA
PRINTER CONTROLLER BOARD
3.9 PRINTER CONTROLLER BOARD
[A]: Printer controller board (! x2)
NOTE: Remove the NVRAM [B] from the old
printer controller board and put it on
the new board.
[A]
G058R710.WMF
[B]
3.10 ENGINE BOARD
[B]
[C]
[A]
[D]
G058R712.WMF
Left cover (☛ 3.2 Exterior Covers)
Printer controller board (☛ 3.9 Printer Controller Board)
[A]: Bracket (! x6, 1 grounding wire)
NOTE: The sheet is used for 230V machine only.
[B]: Clip
[C]: Engine board (! x5, all connectors)
NOTE: Remove the NVRAM [D] from the old engine board and put it on the
new board.
G056/G058
3-16
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
MAIN MOTOR
3.11 MAIN MOTOR
Left cover (☛ 3.2 Exterior Covers)
[A]: Main motor (! x4, " x1)
G058R711.WMF
3.12 SOLENOIDS AND CLUTCHES
[F]
[C]
[D]
[E]
[A]
[B]
G058R714.WMF
Left cover (☛ 3.2 Exterior Covers)
[A]: By-pass feed solenoid (! x1, " x1)
[B]: Gear (1 hook)
[C]: Stopper (! x1)
[D]: Relay clutch (1 hook, " x1)
[E]: Paper feed clutch (1 hook, " x1)
Main motor (☛ 3.11 Main Motor)
[F]: Registration clutch (# x1, " x1)
SM
3-17
CÓPIA NÃO CONTROLADA
G056/G058
Replacement
and
Adjustment
[A]
CÓPIA NÃO CONTROLADA
POWER SUPPLY UNIT AND HIGH VOLTAGE SUPPLY BOARD
3.13 POWER SUPPLY UNIT AND HIGH VOLTAGE SUPPLY
BOARD
[A]
G058R707.WMF
[D]
[B]
[C]
G058R708.WMF
[E]
G058R709.WMF
Left cover (☛ 3.2 Exterior Covers)
Fusing unit (☛ 3.6.1 Fusing Unit)
[A]: PSU cover (! x2)
[B]: PSU assembly (! x9, all connectors)
[C]: High voltage supply board (! x4)
[D]: 230V machine only: Choke coil (! x2, " x1)
[E]: Power supply unit (! x5)
G056/G058
3-18
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IMAGE ADJUSTMENT
3.14 IMAGE ADJUSTMENT
3.14.1 REGISTRATION ADJUSTMENT
The registration is adjusted using the user mode; “Maintenance-RegistrationAdjustment”
3.14.2 PARALLELOGRAM IMAGE ADJUSTMENT
Replacement
and
Adjustment
NOTE: Use the scanner positioning pin (P/N: A0069104) for the adjustment.
Do the following procedure if a parallelogram is printed while adjusting the printing
registration using a trimming pattern.
(a)
(b)
G058R210.WMF
G056R500.WMF
1. Remove the upper cover (☛ 3.2 Exterior Covers)
2. Set a positioning pin to one of the hole (The above illustration explains when
the image (a) is printed out).
3. Loosen four screws and move the laser unit.
4. Tighten the laser unit.
5. Print the trimming area pattern to check the image. If it is still the same, repeat
step 3 to 5.
SM
3-19
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
TROUBLESHOOTING
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
4. TROUBLESHOOTING
4.1 SERVICE CALL CONDITIONS
4.1.1 SUMMARY
There are 2 levels of service call conditions.
A
B
Definition
To prevent the machine from being
damaged, the SC can only be reset by a
service representative.
The machine cannot be operated at all.
The SC can be reset by turning the
operation switch off and on, if the SC was
caused by a sensor error.
Reset Procedure
Enter engine service mode
(Fusing Error Clear) and press
“#”.
Turn the main power switch off
and on.
NOTE: 1) If the problem concerns electrical circuit boards, first disconnect then
reconnect the connectors before replacing the PCBs.
2) If the problem concerns a motor lock, first check the mechanical load
before replacing motors or sensors.
SM
4-1
CÓPIA NÃO CONTROLADA
G056/G058
Troubleshooting
Level
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
4.1.2 SC CODE DESCRIPTIONS
Code No.
302
B
Symptom
Charge roller current leak
A charge roller current leak signal is
detected.
320
B
Polygon motor error
The polygon motor does not reach its
operating speed within 10 seconds
after the polygon motor on signal, or
the lock signal is not detected for
more than a certain time during
operation.
322
B
1st laser synchronization error
The laser synchronization detector
cannot detect the laser
synchronization signal for more than
5 consecutive 100 ms intervals.
323
B
LD drive current exceeded
The LD driver detects this error for
more than 500 ms.
326
B
• Laser synchronization detector
board out of position
• LD unit defective
• Engine board defective
391
B
2nd laser synchronization error
The 1st LD1 is already on, but the
laser synchronization detector cannot
detect the laser synchronization
signal from the 2nd LD for more than 5
consecutive 100 ms intervals.
Development bias leak
A development bias leak signal is
detected.
500
B
Main motor lock
A main motor lock signal is not
detected for more than 700 ms after
the main motor starts to rotate, or the
lock signal is not detected for more
than a certain time during rotation
after the last signal.
• Main motor defective
• Too much load on the drive
mechanism
541
A
Unstable fusing temperature
During warm-up, the fusing
temperature rises by less than 20 °C
during 11 seconds.
The fusing temperature detected by
the thermistor was 0 °C 5 seconds
after the fusing relay was turned on.
•
•
•
•
•
G056/G058
•
•
•
•
•
Possible Cause
Cartridge (charge roller) defective
High voltage supply board
defective
Poor cartridge connection
Polygon motor
Polygon motor cable
• Laser synchronization detector
board out of position
• Laser synchronization detector
board or cable defective
• Laser synchronization mirror out of
position
• LD unit defective
• Engine board defective
• LD unit defective
• High voltage supply board
defective
• Poor cartridge connection
Thermistor defective
Fusing lamp open
Fusing thermostat open
Power supply board defective
Poor connection of the fusing unit
4-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
Symptom
Fusing temperature warm-up error
The fusing temperature does not
reach more than 80 °C 17.5 seconds
after the main switch is turned on.
543
A
545
A
Fusing overheat error
A fusing temperature of over 245 °C
is detected for 1 second by the fusing
thermistor.
A fusing temperature of over 235 °C
is detected for 1 second after the
fusing lamp has been turned off.
Fusing lamp stays on
The fusing lamp stays on more than
12 seconds after the main motor has
been turned off.
546
A
547
B
610
B
650
B
651
B
726
B
SM
Unstable fusing temperature
During standby, within 500 ms, the
fusing temperature goes below 60 °C
twice or over 60 °C three times.
Within 1 minute, a 60 °C increase or
decrease in fusing temperature is
detected during five different onesecond intervals.
Zero cross signal malfunction
Zero cross signals are not detected
within 5 seconds.
Communication error - duplex unit
The engine board cannot
communicate with the duplex unit.
Communication error - GAVD
• The engine board detects an
unknown device on the I2C I/F
bus (internal bus on the engine
control board).
• The engine board detects an I2C
I/F bus error.
Communication error - FCI
• The engine board detects an
unknown device on the I2C I/F
bus (internal bus on the engine
control board).
• The engine board detects an I2C
I/F bus error.
Shift tray motor error
Tray shift did not finish within a
certain time after the shift motor
turned on.
•
•
•
•
•
•
•
Possible Cause
Thermistor defective
Fusing lamp open
Fusing thermostat open
Power supply board defective
Poor connection of the fusing unit
Fusing thermistor defective
Power supply board defective
• Fusing thermistor defective
• Power supply board defective
• Poor connection of the fusing unit
• Fusing thermistor defective
• Power supply board defective
• Poor connection of the fusing unit
Troubleshooting
Code No.
542
A
• Power supply board defective
• Poor mains power supply condition
• Poor connection between engine
board and duplex unit
• Engine board defective
• Duplex control board defective
• Engine board defective
• Engine board defective
• Shift motor defective
• Shift tray: Left shift sensor or right
shift sensor defective
4-3
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CONTROLLER ERROR
4.2 CONTROLLER ERROR
The following table describes the controller error codes. These codes are displayed
at power-on, or after the power-on self-test, if an error occurs.
Please refer to section 5.3 for details of the power-on self-test.
Code
640
Description
Engine to controller communication
error.
641
Engine to controller communication
error (no answer).
800
Video data error
820
Controller CPU error
821
CPU and ASIC timer error
822
HDD timeout error
823
NIB self test error
824
NVRAM error
827
SDRAM error
828
Flash ROM error
829
Optional RAM error
835
Parallel interface error
836
837
838
Font ROM error
Optional font ROM error
Clock generator error
850
NIB interface error
851
IEEE1394 interface error
G056/G058
Required Action
• Check the connection between the
controller and the engine board.
• Replace the engine board if the error is
consistent.
• Replace the controller if the error is
consistent.
• Check the connection between the
controller and the engine board.
• Replace the engine board if the error is
consistent.
• Check the connection between the
controller and the engine board.
• Replace the engine board if the error is
consistent.
• Replace the controller if the error is
consistent.
• Turn off the machine and turn it back on.
• Replace the controller if the error is
consistent.
• Check the connection between the HDD
and the controller
• Replace the HDD if the error is consistent.
• Turn off the machine and turn it back on.
• Check the connection between the NIB
and the controller.
• Replace the NIB if the error is frequent.
• Replace the NVRAM if the error is
consistent.
• Replace the controller if the error is
consistent.
• Replace the controller if the error is
consistent.
• Check the connection of the optional
memory.
• Replace the optional memory if the error
is consistent.
• Replace the controller if the error is
consistent.
• Not used for this model.
• Not used for this model.
• Replace the controller if the error is
consistent.
• Replace the controller if the error is
consistent.
• Replace the controller if the error is
consistent.
4-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
CONTROLLER ERROR
Code
860
Description
HDD start-up error
HDD damaged cluster error
HDD data unable to read
HDD data access error
HDD access error
Controller counter error
999
Software update error
• Replace the NVRAM if the error is
consistent.
• Try downloading the controller software
again.
Troubleshooting
862
863
864
865
900
Required Action
• Turn off the machine and turn it back on.
• Check the connection between the HDD
and the controller.
• Replace the HDD if the error is consistent.
• Replace the HDD if the error is consistent.
SM
4-5
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
ELECTRICAL COMPONENT DEFECTS
4.3 ELECTRICAL COMPONENT DEFECTS
4.3.1 SENSORS
Component
CN
Condition
Open
Paper Exit
6-B2
Shorted
Paper Overflow
Open
6-B5
Shorted
Open
Registration
16-A2
Shorted
Open
1st Paper End
16-A5
Shorted
1st Paper Height
16-A8
Toner End
16-A12
Open
Shorted
High
Low
Symptom
The Paper Jam indicator will light whenever
a print is made.
The Paper Jam indicator lights even if there
is no paper.
The paper overflow message is not
displayed even when a paper overflow
condition exists.
The paper overflow message is displayed.
The Paper Jam indicator will light whenever
a print is made.
The Paper Jam indicator lights even if there
is no paper.
The Paper End indicator lights even if paper
is placed in the 1st paper tray.
The Paper End indicator does not light even
if there is no paper in the 1st paper tray.
Misfeed is indicated when paper supply
runs out.
The machine cannot determine the paper
near-end condition properly.
Toner near-end (toner end) is not detected.
The add toner message is displayed.
NOTE: The CN numbers describe the connector number on the engine board.
4.3.2 SWITCHES
Component
Main
CN
272-1,3
(PSU 120V)
270-1,2
(PSU 230V)
Condition
Open
Shorted
Open
Front Cover
Safety
9-1
Rear Cover
Safety
9-3
5-3
Symptom
The machine does not turn on.
The machine does not turn off.
Shorted
Open
Shorted
The Front Cover Open message is not
displayed even if the front cover is opened.
The Front Cover Open message is
displayed even if the front cover is closed.
The Rear Cover Open message is not
displayed even if the rear cover or paper
exit cover is opened.
The Rear Cover Open message is
displayed even if the rear cover or paper
exit cover is closed.
NOTE: The CN numbers describe the connector number on the engine board
(except for the main switch).
G056/G058
4-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
BLOWN FUSE CONDITIONS
4.4 BLOWN FUSE CONDITIONS
Fuse
115 V
Power Supply Board
FU1
15 A/125 V
FU2
6.3 A/250 V
FU3
5 A/125 V
FU4
5 A/125 V
Rating
220 - 240 V
---3.15 A/250 V
5 A/250V
5 A/250V
Symptom when turning on the main
switch
No power
No power
No power
No power
(LEDs flash once)
4.5 LEDS
Troubleshooting
No LEDs are used for this model (except for the NIB - refer to section 6.7).
SM
4-7
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
FIRMWARE HISTORY
Rev. 05/2000
4.6 FIRMWARE HISTORY
4.6.1 G056/G058 FIRMWARE MODIFICATION HISTORY
G056/G058 FIRMWARE MODIFICATION HISTORY
PART
NUMBER
G0565920 B
DESCRIPTION OF MODIFICATION
• First Mass Production of Machine
• Firmware modified to make corrections for
the German language.
• Does not exist in the field
• Does not exist in the field
1. Firmware modified to improve print quality
when image data is printed using the PCL6
driver.
NOTE: This occurs only in the following
condition.
• When printing image data
• When using the PCL6 driver
G0565920 C
G0565920 D
G0565920 E
G0565920 F
SERIAL
NUMBER
1 st Mass
Production
November 2000
production
N/A
N/A
December 2000
production
FIRMWARE
VERSION
1.01
1.02
1.03
1.04
1.05
2. New feature added in the user mode.
“Curl Prevention” mode is added in the user
mode. (Curl Prevention: User mode/
Maintenance). Please note that the function
of this mode is the same as the “Curl Control”
in the printer engine service mode. It lowers
the fusing temperature to prevent paper from
curling. Advise customer to use this mode
when paper jam occurs during duplex rear
side printing.
NOTE: When this mode is switched on, the
“Curl Control” in the service mode is
also switched on.
Symptom:
In PCL printing, if data exists over the bottom
edge of the printable area, the machine
freezes, displaying "Processing" and
operation will no longer be possible.
Condition:
Printer driver is not being used
Print data exists on the bottom edge of the
printable area (at 4.2mm)
Action:
Update the controller firmware.
G056/G058
4-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Rev. 08/2001
FIRMWARE HISTORY
G056/G058 FIRMWARE MODIFICATION HISTORY
DESCRIPTION OF MODIFICATION
⇒•
SERIAL
NUMBER
Does not exist in
the field
FIRMWARE
VERSION
1.06
G0565920 J
February 2001
production
1.08
Troubleshooting
Corrects the following:
In rare cases with graphic images, a dark
band(s) appears or part of the image
becomes black on prints.
Corrects the following:
• Modified so the machine can be used
with Axis print servers.
• Modified to correct Polish and
Portuguese langauage errors.
PART
NUMBER
G0565920 G
SM
4-9
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SERVICE TABLES
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SERVICE PROGRAM MODE
5. SERVICE TABLES
5.1 SERVICE PROGRAM MODE
!CAUTION
Before accessing the service menu, do the following:
Confirm that there is no print data in the printer buffer (the Data In LED
must not be lit or blinking).
If there is some data in the buffer, wait until all data has been printed.
5.1.1 ENABLING AND DISABLING SERVICE PROGRAM MODE
Entering the Service Mode
Method 1: Turn the machine on while pressing the “On
Line” key and “Escape” key together until “1. Service
Menu1” appears on the display.
Menu
On Line
NOTE: If you switch the machine off, any jobs stored
on the hard disk using the sample print and
Job Reset
Escape
protected print features will be deleted.
Check first with the user tools to see if there are
Form Feed
# Enter
any jobs stored with these features
(Menu key - Sample Print, or Protected Print).
Power
Error
Data In
Method 2: Press the “Up/Down arrow” keys together for
about 5 seconds, then press the “Enter” key.
G058D520.WMF
“1. Service Menu1” appears on the display.
NOTE: The machine automatically goes off line when you enter the service mode.
Accessing the Required Program
Use the “Up/Down arrow” keys to scroll through the menu listing.
1. Service Menu: Controller service modes
2. Engine Mainte: Engine service modes
3: End: Exit service mode
To select an item, press the “Enter” key. Then the sub-menu will appear.
Scroll through the sub menu items using the “Up/Down arrow” keys.
To go back to a higher level, press the “Escape” key.
SM
5-1
CÓPIA NÃO CONTROLADA
G056/G058
Service
Tables
There are two ways to enter the service mode.
CÓPIA NÃO CONTROLADA
PRINTER CONTROLLER SERVICE MODE
Rev. 10/2003
Inputting a Value or Setting for a Service Program
Enter the required program mode as explained above. The setting appearing on
the display is the current setting.
Select the required setting using the “Up/Down arrow” keys, then press the “Enter”
key. The previous value remains if the “Enter” key is not pressed.
Exiting Service Mode
Select “3. End” from the service mode main menu, then press the “Enter” key.
NOTE: To make the settings effective, turn the main switch off and on after exiting
service mode.
5.2 PRINTER CONTROLLER SERVICE MODE
5.2.1 SERVICE MODE MENU (‘1. SERVICE MENU’)
⇒
Service
Mode
Bit Switch
Clear Setting
Service Print
Disp Version
Description
Bit switch
settings
Initializes the
system settings
Controller
summary print
Display
controller
Function
Adjusts bit switch settings.
5.2.2 Bit Switch Programming
Initializes settings in the “System” menu of the user mode.
Prints the service summary sheet (a summary of all the
controller settings).
Displays the version of the controller firmware.
5.2.2 BIT SWITCH PROGRAMMING
NOTE: Currently, the bit switches are not being used.
1. Enter the SP mode, select “Service Menu”, then press
[Enter] twice.
Service Menu
BitSW
2. Select #1, #2, #3, or #4 for the desired bit switch, then
press [Enter].
• [V] [W]: Move to the next switch.
BitSW
<BitSW#1>
Sw#1 00000000
3. Adjust the bit switch using the following keys.
Bit0
_
• [V] [W]: Move to the next bit.
• [Escape]: Exit without saving changes.
• [Enter]: Exit and save changes.
NOTE: The left digit on the display is bit 7 and the right digit is bit 0.
4. Press [Enter] to save changes and exit.
G056/G058
5-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTER CONTROLLER SERVICE MODE
Rev. 10/2003
⇒ Bit Switch 1
Bit Switch 01 - Not used (do not change any of these settings)
Bit Switch 2
Bit Switch 02
No
Description
0-2 Not used
PDL Sniffing
3
Treatment of the last page
when printing a job with an
odd number of pages using
the duplex unit
4
0: (default): Last page not
fed through the duplex unit
1: Last page fed through the
duplex unit
5-7 Not used
Function
Do not change the setting.
See PUB(C)-051 for details
0: The last page is not fed through the duplex unit, so the
last page faces the opposite way from other pages in the
job.
1: The last page is fed through the duplex unit, so the last
page faces the same way as other pages of the job.
Set this switch to “1” when the customer wishes the last
page to be facing the same way as the other pages.
Do not change the setting.
Bit Switch 3
Bit Switch 03
No
Description
PS Fonts Download
0
1-7 Not used
Function
See PUB(C)-045 for details
Do not change the setting.
Service
Tables
Bit Switch 4
Bit Switch 04 - Not used (do not change any of these settings)
SM
5-3
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
5.3 PRINTER ENGINE SERVICE MODE
5.3.1 SERVICE MODE TABLE (‘2. ENGINE MAINTE’)
Service
Mode
Regist sag
Description
Paper feed
timing
Fusing
Control
Fusing power
control
Fusing
Temp
Fusing
temperature
adjustment
Fusing
temperature
display
Bypass paper
feed roller
rotation for
transparencies
Fusing
T Dis
OHP
Clutch Rt
Function
Fusing
Start
Initial fusing
setting
Curl
Control
Low temperature
fusing
Charge
Rol Bias
Charge roller
voltage
adjustment
Main scan
magnification
adjustment
Sub scan
magnification
adjustment
Development
Bias Adjustment
Mainscan
mag
Subscan
mag
Developer
Bias
Toner End
Count
G056/G058
Number of prints
after toner nearend is detected
Setting
Adjusts the paper feed clutch timing at
registration. The paper feed clutch
timing determines the amount of paper
buckle at registration. (A larger setting
leads to more buckling.)
Selects whether the fusing power
control is on/off or phase control.
Use “Phase” control if the room lights
flicker when the fusing lamp starts.
Adjusts the fusing temperature for
printing.
Normally, do not change the setting.
Displays the fusing temperature.
-8.0 to +8.0
2 mm/step
0 mm
Selects the number of rotations for the
bypass tray feed roller when the paper
type is set to “Transparencies.”
This is to avoid jams when
transparencies are being used.
Roller turn: Warms up the fusing unit for
20 s at power on or when the machine
warms up from the energy saver mode.
Normal: There is no 20 s warm-up
period
Select ‘roller turn’ to avoid poor fusing in
a low temperature environment.
Lowers the fusing temperature (to
150°C) to prevent thin paper from
curling. Use this mode only when a
paper jam occurs during duplex rear
side printing.
Adjusts the charge roller voltage.
Normally, do not change the setting.
1 (1 rotation)
2 (2 rotations)
Adjusts the main scan magnification.
Adjusts the sub scan magnification.
Adjusts the development bias for
printing.
Normally, do not change the setting.
Adjusts the number of prints the
machine can print after it detects toner
near-end.
5-4
CÓPIA NÃO CONTROLADA
Normal
(US)
Phase
(Europe/Asia)
100 to 200
10°C/step
170°C
Normal
Roller turn
Normal
Curl control
1000 to 2000
10 V/step
1650V
-0.5 to +0.5
0.1 %/step
0%
-0.5 to +0.5
0.1 %/step
0%
-800 to -200
10 V/step
-700V
50 to 200
50 sheets/step
200 sheets
SM
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Service
Mode
Transfer
curr
Transfer current
correction
Adjusts the correction current applied to
the transfer roller.
Test
Pattern
Test pattern
selection
Thermistor
adj
Thermistor
adjustment
Toner end
clear
Toner end clear
(engine)
Waste
Toner Cnt
Effective
info
Waste toner
count display
Cartridge ID chip
features that are
used
Cartridge
lmt
Number of prints
for a single
cartridge
Use this to select and print a test
pattern. This machine has the following
patterns.
• No specified
• Checkered flag
• Cross-stitch
• 1-dot argyle
• 2-dot argyle
• 2-dot trim
• 1-dot grid
• 2-dot grid
Reset this to 0 after printing the test
pattern.
Charge roller voltage and transfer
current automatic adjustment.
The machine automatically adjusts
these parameters in response to the
temperature within the machine.
Normally, do not change the setting.
Clears the toner end counter in the
engine board.
Note: This mode is not used in this
machine.
Displays the waste toner counter in the
engine board.
Selects which of the cartridge ID chip
functions are enabled.
• Not used: All items are not used
• All used: All items are used
• Normal Mode: Cartridge
detection/type
• Cartridge: Cartridge detection only
Adjusts the number of prints the
machine can make after a new cartridge
is detected.
Do not use a higher value than 30 k.
Waste Lim
Stop
Action when
toner end is
detected
SM
Function
Determines whether the machine stops
printing after the cartridge counter
reaches the above limit.
5-5
CÓPIA NÃO CONTROLADA
Setting
0: –2 µA
1: 0 µA
2: +2 µA
3: +4 µA
No pattern
On
Off
Service
Tables
Description
15k prints
20k prints
25k prints
30k prints
35k prints
40k prints
Yes
(Stop printing)
No
(Do not stop)
G056/G058
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Service
Mode
Toner end
sensor
Toner near-end
threshold
Cartridge
info
A3/11x17
Count
Toner cartridge
information
A3/DLT double
count
Memory
clr
Memory clear
Free run
Free run
Input
check
Input check
mode
Output
check
Output check
mode
Fusing err
clr
SC code reset
Serial
number
Service
TEL
Serial number
programming
Service station
number
programming
HDD Init
Initializes the
HDD
---
Prog
Checksum
G056/G058
Description
Function
Threshold adjustment for the toner end
sensor.
Normally, do not change the setting.
Important: Turn the main switch off/on
after changing this setting.
Displays toner cartridge information.
Setting
200 to 1000
100 ms/step
200 ms
Specifies whether the counter is
Yes
doubled for A3/11" x 17" paper.
(double count)
If “Yes” is selected, the total counter
No
counts up twice when A3/11" x 17"
(single count)
paper is used.
Resets software counters and returns modes and settings
to their defaults.
• Memory all clear: Clears all data
• Eng: Clears the printer engine settings (See Note 1 for
a list of the settings erased)
• SCS: Clears system settings (See Note 2 for a list of
the settings erased)
• PRT: Clears user mode system settings (See Note 3
for a list of the settings erased)
• NCS: Clears the items listed in the “Host Interface”
section of the Configuration page.
The machine performs a free run.
Press [Enter] to start.
Press [Enter] to stop.
Please note that the machine will not
stop immediately after the [Enter] key is
pressed.
Displays signals received from sensors
and switches.
See the “Input Check” section for
details.
Turns on electrical components
individually for test purposes.
See the “Output Check” section for
details.
Resets a service call condition (for
fusing unit errors).
After using this SP mode, turn the main
switch off and on.
Use to input the machine serial number.
(This is normally done at the factory.)
Program the service station number.
The number is printed on the metercharge counter report when the metercharge mode is turned on.
Initializes the hard disk. Use this only if
there is a hard disk error.
Designers’ use only
5-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Plug/Play
Meter
charge
Description
Engine test
pattern print
Plug & Play
name selection
Meter-charge
mode
Service
Report
Operation
time
Prints engine
summary
Total engine
rotation cycle
Total
count C
Controller total
counter display
Disp ROM
ver
ROM version
display
SM
Function
Setting
Prints the test pattern that was selected
in the “Test Pattern” mode.
Select the plug & play name.
Enable or disable meter-charge mode.
Important: Turn the main switch off/on
after changing this setting.
Meter charge mode enabled:
• ‘Replace Maintenance Kit’ is not
displayed on the operation panel
when the PM counter runs out (the
technician replaces the
maintenance kit items)
• The meter charge counter is shown
immediately after the Menu key is
pressed.
• The technician must reset the PM
counter after replacing the fusing
unit.
Meter charge mode disabled:
• ‘Replace Maintenance Kit’ is
displayed on the operation panel
when the PM counter runs out (the
user replaces the maintenance kit
items)
• The meter charge counter is not
shown when the Menu key is
pressed.
• The PM counter resets automatically
after the user replaces the fusing
unit.
Prints the engine summary sheet.
Yes
(Enabled)
No
(Disabled)
Service
Tables
Service
Mode
Test Print
Displays the total number of engine
rotation cycles made so far.
Note: One cycle is calculated as 3.7 s
of drum rotation. However, this counter
also includes idle rotations.
This counter is not reset at PM.
Displays the controller total counter.
This counter is used for meter charge,
and it appears when the user presses
the Menu key (if meter charge mode is
enabled).
It does not count up when certain items,
such as service reports, are printed (see
section 6.6.1. for a complete list of
conditions).
Displays the firmware version (system,
engine, and duplex).
5-7
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Service
Mode
PM
Counter
Description
Function
PM counter
display
PM
Counter
reset
Resets the PM
counter
Diag result
Diagnostic result
display
Assert Info
Usercode
clr
Total
counter
--User code clear
Engine total
counter display
Setting
Displays the PM counter. This is not a
page counter. It estimates the page
count using the engine rotation cycle
count. It counts up one page when the
engine has made the average number
of rotations that is required for one page
of a three-page job.
Resets the PM counter.
Important: If a technician replaces the
PM items, reset this counter after
replacing these items.
Displays the controller self-diagnostic
result.
See sections 5.5 and 5.6 for details.
Designers’ use only
Clears all the user code data from the
controller board memory.
Displays the engine total counter. It
counts up for all prints, including service
reports.
Memory Clear
The following tables list the items that are cleared.
Note 1: Eng (Engine settings)
Setting Name
Sub scan registration
Main scan registration
Image Density
Regist sag
Fusing control
Fusing temp
OHP Clutch Rt
Fusing start
Curl control
Charge Rol Bias
Main scan mag
Subs can mag
Developer bias
Toner end count
Transfer curr
Thermistor adj
Effective info
Catridge lmt
Waste Lim Stop
Toner end sensor
Meter charge
G056/G058
User or Service Mode
User/Maintenance/Registration
User/Maintenance/
Service/Printer engine
5-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Note 2: SCS (Clears system settings)
Setting Name
Language
Paper Type
Tray Paper Type
Manually programmed
paper size
Tray Lock
Energy saver timer
A3/11x17 Count
Service TEL
User code counter
User or Service Mode
User/
User/Paper Input/
User/System/
Service/Printer engine
---
Note 3: PRT (Clears system settings)
SM
User or Service Mode
User/Paper Input
User/System
Service
Tables
Setting Name
Tray Priority
Misfeed Recovery
Print Error Report
Auto Continue
Memory Overflow
Output Tray
Job Separation
Memory usage
5-9
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
5.3.2 INPUT CHECK TABLE
Number
1
Front cover safety switch
2
3
4
Main motor lock
Polygon motor lock
Not used
5
Upper rear cover (duplex cover)
6
7
8
9-10
11
12-15
16
17
18
19
20
21
22
23
24
25
26
27-28
29
30
31
32
33
34
35
36
37-40
41
G056/G058
Reading
Description
00
Closed
Off
Off
Not installed
Not installed
Used fusing unit
Opened
(Pushed)
Installed
Installed
New fusing unit
Paper not detected
Paper detected
Paper not detected
Paper not detected
Paper detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper detected
Paper detected
See table 1
See table 3
Paper not detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Closed
Duplex unit installed
Fusing unit installed
New fusing unit detection
Not used
Paper overflow sensor
Not used
Registration sensor
Paper exit sensor
Duplex transport sensor
(optional duplex unit)
Duplex entrance sensor
(optional duplex unit)
Duplex exit sensor
(optional duplex unit)
Bypass feed paper sensor
Paper end sensor - standard cassette
Paper size sensor - standard cassette
Paper height sensor - standard cassette
Not used
Paper end sensor - optional paper tray
upper cassette
Not used
Paper end sensor - optional paper tray
lower cassette
Paper size sensor - optional paper tray
lower cassette
Paper height sensor - optional paper
tray lower cassette
Upper paper transport sensor
(optional paper feed unit)
Lower paper transport sensor
(optional paper feed unit)
Paper size sensor - optional paper tray
upper cassette
Not used
Paper height sensor - optional paper
tray upper cassette
Not used
Paper output tray cover sensor
01
Opened
(Pushed)
On
On
See table 2
See table 4
Paper not detected
Paper detected
Paper not detected
Paper detected
See table 2
See table 4
Closed
5-10
CÓPIA NÃO CONTROLADA
Opened
(Interrupted)
SM
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Description
42
Shift tray paper transport sensor
Shift tray at right
(optional 1-bin shift tray)
Shift tray at left
(optional 1-bin shift tray)
Paper sensor - 1st bin
(optional 4-bin mailbox)
Paper overflow sensor - 1st bin
(optional 4-bin mailbox)
Paper sensor - 2nd bin
(optional 4-bin mailbox)
Paper overflow sensor - 2nd bin
(optional 4-bin mailbox)
Paper sensor - 3rd bin
(optional 4-bin mailbox)
Paper overflow sensor – 3 rd bin
(optional 4-bin mailbox)
Paper sensor - 4th bin
(optional 4-bin mailbox)
Paper overflow sensor – 4th bin
(optional 4-bin mailbox)
Upper paper transport sensor - Mailbox
(optional 4-bin mailbox)
Lower paper transport sensor - Mailbox
(optional 4-bin mailbox)
Not used
43
44
45
46
47
48
49
50
51
52
53
54
55-75
Reading
00
01
Paper not detected
Paper detected
On
Off
(Interrupted)
On
Off
(Interrupted)
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Paper not detected
Paper detected
Service
Tables
Number
Table 1: Paper Size Switch (Main Unit)
Number
SW 1
SW 2
SW 3
23
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Paper Size
US model
Europe/Asia
----LG SEF
A4 LEF
81/2" x 13"
11" x 81/2"
11" x 81/2"
A4 SEF
* (Asterisk)
* (Asterisk)
A4 LEF
81/2" x 11"
81/2" x 11"
A5 LEF
11" x 17"
A3
1: Pushed
Switch No. 1
2
3
G056M500.WMF
SM
5-11
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Table 2: Paper Size Switch (optional paper tray)
Number
SW 1
SW 2
SW 3
SW 4
0
0
0
30, 34
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Paper Size
US/
Europe/Asia
---
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
* (Asterisk)
--A4 LEF
--LG SEF
--A4 SEF
--11" x 81/2"
--81/2" x 11"
--11" x 17"
--A3
1: Pushed
---: Cassette not detected
Table 3: Paper Height Sensor (standard cassette)
Number
24, 31
SP Value
00H
01H
Paper Amount
More than 20%
Less than 20%
Table 4: Paper Height Sensor (optional paper tray)
Number
36
G056/G058
SP Value
00H
01H
02H
03H
Paper Amount
Less than 10%
More than 90%
10 - 50%
50 - 90%
5-12
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
5.3.3 OUTPUT CHECK TABLE
SM
Description
Main motor (forward)
Paper transport clutch
Registration clutch
Not used
Paper feed clutch (standard cassette)
Bypass feed solenoid
Not used
Fan motor (high speed)
Fan motor (low speed)
Fusing relay
Not used
Polygon motor on
Polygon motor on and LD on
Not used
Upper paper feed clutch (optional paper tray unit)
Upper paper feed motor (optional paper tray unit)
Lower paper feed clutch (optional paper tray unit)
Lower paper feed motor (optional paper tray unit)
Not used
Paper exit motor (1-bin shift tray, 4-bin mailbox)
Paper exit junction gate solenoid
1-bin shift tray - right
1-bin shift tray - left
Mailbox turn gate solenoid 2 (optional 4-bin mailbox)
Mailbox turn gate solenoid 3 (optional 4-bin mailbox)
Mailbox turn gate solenoid 4 (optional 4-bin mailbox)
Not used
Duplex inverter motor (forward: optional duplex unit)
Duplex inverter motor (reverse: optional duplex unit)
Duplex transport motor (Optional duplex unit)
Inverter gate solenoid (Optional duplex unit)
Not used
5-13
CÓPIA NÃO CONTROLADA
Service
Tables
Number
1
2
3
4
5
6
7-10
11
12
13
14-21
22
23
24-25
26
27
28
29
30
31
32
33
34
35
36
37
38-40
41
42
43
44
45-50
G056/G058
CÓPIA NÃO CONTROLADA
FIRMWARE UPDATE PROCEDURE
Rev. 08/2001
5.4 FIRMWARE UPDATE PROCEDURE
5.4.1 CONTROLLER/NIB/ENGINE FIRMWARE UPDATE
This procedure is for upgrading the firmware of the machine.
⇒
!CAUTION
Do not turn off the machine while
downloading the firmware.
[C]
NOTE: When you see the machine from the
[A]
back, the “A” side of the card must
face the right as shown.
[B]
G058R713.WMF
1. Prepare 2 IC cards with the controller firmware.
2. Turn off the main switch.
3. Remove the IC card slot cover [A] on the rear side of the machine as shown.
4. Insert the IC card-1 [B] into slot [C] and turn on the main
Onboard Sys. 1/2
switch. “Onboard Sys. 1/2” is displayed.
5. Press “# Enter.”
Note: Make sure that ∗ is displayed.
Onboard Sys. 1/2
∗
6. Scroll with the [!] ["] key and select “Update.”
Press “# Enter” to start downloading.
The “On Line” LED starts blinking and the machine starts
to download the program.
(Notice that the ∗ mark disappears as the program is
downloaded.)
Update
Updating
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
7. When updating card-1 is finished, “Update 1/2 task done”
is displayed.
Update 1/2 task done
8. Turn off the main switch and replace the card with IC card2. Turn on the main switch, then downloading will
automatically start.
Updating
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
9. When updating card-2 is finished, “Update done” is
displayed. Then, remove the card, turn on the main switch
and print the configuration sheet. Check that controller
firmware is successfully updated.
Update done
G056/G058
5-14
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
FIRMWARE UPDATE PROCEDURE
5.4.2 ERROR RECOVERY
Controller
If an error occurs during updating the controller firmware, use the following
procedure. This procedure will force the controller to boot from the IC card.
1. Prepare two FlashROM cards with the required controller firmware version.
2. Turn off the machine and remove the controller.
CN1
Parallel I/F
3. Change the DIP switch 2 - No. 1 setting to “ON”.
Engine Board
Controller Board
NIB
SW2
Bit 4
3
2
1
OFF
G056T500.WMF
4. Put back the controller and insert the first card into the FlashROM card slot on
the controller.
NOTE: When you see the machine from the back, the “A” side of the card must
face the right.
5. Turn on the machine. The machine automatically starts to download the
software.
6. When downloading is finished, “Update done” is displayed.
7. Turn off the machine, remove the first card, and insert the second card.
8. Repeat steps 5 and 6.
9. Turn off the machine, remove the first card, and reset the DIP switch 2 - No.1
setting to “OFF”. Then, put back the controller.
NOTE: The default settings of the DIP switches are all ‘OFF’.
10. Turn on the machine, and print the service summary report.
NIB/Engine Board
If a download attempt failed, try downloading the new firmware again using the
procedure described in section 5.4.1.
SM
5-15
CÓPIA NÃO CONTROLADA
G056/G058
Service
Tables
ON
CÓPIA NÃO CONTROLADA
POWER-ON SELF TEST
5.5 POWER-ON SELF TEST
This self diagnostic test requires a loop-back connector (P/N: G0219350).
1. Turn off the machine and attach the loop-back connector to the parallel
interface.
2. Turn on the machine while pressing the “On Line” key and “# Enter” key
together.
3. The machine prints the diagnostic report automatically.
• Refer to section 5.3.1 for how to check the error codes (Engine service mode
– Diag result)
• Refer to section 4.2 for details about the error codes.
5.6 OTHER TESTS
The controller tests the following devices at power-on. If an error is detected, an
error code is stored in the controller board.
• CPU, ASIC and clock
• Flash ROM
• Resident and optional SDRAM
• Parallel interface
• NIB
• IEEE1394 interface (if installed)
• NVRAM
• Optional HDD (if installed)
• Refer to section 5.3.1 for how to check the error codes (Engine service mode Diag result)
• Refer to section 4.2 for details about the error codes.
G056/G058
5-16
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
USER PROGRAM MODE
Rev. 12/2002
5.7 USER PROGRAM MODE
Press the “Menu” button and use the “Up/Down arrow” keys to scroll through the
menu listing.
To go back to a higher level, press the “Escape” key.
After changing the settings, press the “On Line” key.
The user menu list can be printed using “Menu List” in the “List/Test Print” user
mode.
⇒User Mode Tree
User Mode
Counter (Meter-charge mode must be "On")
Sample Print (optional HDD required)
Locked Print (optional HDD required)
Paper Input
By-Pass Size
Tray Paper Size
Paper Type
Tray Locking
List/Test Print
Maintenance
Tray Priority
Image Density
Registrationn
Curl Prevention
HDD Format (optional HDD required)
Menu Protect
Paper Size Error
System
Misfeed Recovery
Print Error Report
Auto Continue
Service
Tables
Memory Overflow
Duplex (optional duplex unit required)
Output Tray (only installed trays are displayed)
Job Separation (1-bin shift tray required)
Energy Saver
Memory Usage
Unit of Measure
Edge Smoothing
Resolution
Toner Saving
Host Interface
I/O Buffer
I/O Timeout
Network Setup (NIB required)
PCL Menu
Orientation
Form Lines
Font Source
Font Number
Point Size
Font Pitch
Language
Symbol Set
G056M501.WMF
SM
5-17
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
DIP SWITCHES
5.8 DIP SWITCHES
Controller Board
CN1
Parallel I/F
DIP switch 2 (Bit 1) on the controller is used for error recovery after a firmware
updating procedure failed.
NOTE: The default settings of the DIP switches are all ‘OFF’.
Engine Board
Controller Board
NIB
SW2
Bit 4
3
2
1
OFF
ON
G056T500.WMF
Engine Board
DIP switch 1 on the engine board is for factory use only. Do not change the setting.
G056/G058
5-18
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
DETAILED DESCRIPTIONS
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
OVERVIEW
6. DETAILED SECTION DESCRIPTIONS
6.1 OVERVIEW
6.1.1 MECHANICAL COMPONENT LAYOUT
1
15
14
2
3
13
4
12
5
11
6
10
7
G058D106.WMF
1. Laser unit
9. Registration roller
2. Cartridge (AIO-type)
10. Transfer roller
3. Charge roller
11. Drum
4. Development roller
12. Pressure roller
5. By-pass feed tray
13. Hot roller
6. By-pass feed roller
14. Paper exit roller
7. Paper feed roller
15. Quenching lamp
Detailed
Descriptions
8
9
8. Friction pad
SM
6-1
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
OVERVIEW
6.1.2 PAPER PATH
[A]
[D]
[C]
[B]
G058D110.WMF
G058D109.WMF
[A]: Optional four-bin mailbox
[B]: Optional paper tray unit
(the top tray can be an envelope feeder)
[C]: Optional duplex unit
[D]: Optional one-bin shift tray unit
G056/G058
6-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
BOARD STRUCTURE
6.2
BOARD STRUCTURE
6.2.1 OVERVIEW
Standard
components
IEEE1284
Interface
Optional
components
NIB
Printer
Controller
Board
Standard
PCB
* 1,2
IEEE1394* 1
Interface
Memory
DIMM
Power
Pack
Motors
Polygon
Motor
LDDR
Synch.
Detector
HDD
PCI Bus
Operation
Panel
(Laser Control Block)
Engine Board
PSU
Fusing Lamp
4-bin
Mailbox
1-bin
Shift Tray
Duplex
Unit
Clutches
Sensors
Thermistor
Paper
Tray
Unit
(Lower)
G058V501.WMF
The engine board controls all the mechanical components. The NIB, memory
DIMM, and the HDD can be installed on the controller board.
The printer controller board connects to the engine board through a PCI bus.
The NIB (network interface board) or IEEE1394 board can be installed on the
G056 model as options.
NOTE: 1) The NIB and the IEEE1394 board cannot be installed at the same time.
2) The NIB is a standard component for the G058 but not the G056.
SM
6-3
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
ID Chip
(Cartridge)
Paper
Tray
Unit
(Upper)
CÓPIA NÃO CONTROLADA
BOARD STRUCTURE
6.2.2 DESCRIPTIONS
1. Engine Board
The engine board controls the following functions:
• Engine sequence
• Machine and printer engine operation
• Timing for peripherals
• High voltage supply, laser, and fusing
• Sensors, motors, and solenoids
2. Printer Controller Board
The printer controller board handles the following functions:
• Printer-to-host interface
• Operation panel interface
• Interfacing and control of the NIB (or IEEE1394) and other options (HDD
and DRAM DIMM)
3. LD Drive Board
This is the laser diode drive circuit board.
4. Network Interface Board (NIB )
The network interface board allows the printer to be used on a network.
5. IEEE1394 Interface (Option)
This allows computers to connect to this printer using an IEEE1394 interface.
6. HDD Unit (Option)
The HDD unit stores the data for the following.
• Additional soft fonts
• Collation
• Protected print
• Sample print
• Downloading forms for form overlay
7. Memory DIMM (Option: 64MB DRAM)
This is for additional printer processing memory, collation, and for soft fonts.
8. Control Panel Board
Controls the display panel, the LED, and the keypad.
9. IEEE1284 Interface
This is a parallel printer port.
G056/G058
6-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
BOARD STRUCTURE
6.2.3 CONTROLLER BOARD
CPU
RM 5231
PCI
IEEE1394 I/F
PCI
Engine I/F
HD D I/F
Option .2.13
SDRAM -D IM M
IEEE 1284 I/F
ASIC
SIM AC
SD RAM
Data Bus
Control Signals
ROM-DIMM
(Not used)
NIB I/F
FLASH
RO M
Detailed
Descriptions
NVRAM
IC CARD
I/F
G056D507.WMF
SIMAC:
The SIMAC ASIC is a multi-purpose peripheral controller. It controls
all the functions of the printer controller board.
CPU:
32-bit CPU (RM5231-200)
SDRAM:
32MB SDRAM
Flash ROM:
8MB Flash ROM
NVRAM:
Stores the controller settings
SM
6-5
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
6.3 PRINTING PROCESS
6.3.1 OVERVIEW
1
7
2
6
3
5
4
G058D100.WMF
1) Drum charge: The charge roller gives the drum a negative charge.
2) Laser exposure: A laser beam writes the print data to the drum.
3) Development: The development roller carries toner to the latent image on
the drum surface.
4) Image transfer: The transfer roller pulls the toner from the drum onto the
paper.
5) Separation: The separation plate helps to separate the paper from the drum.
6) Cleaning: The cleaning blade removes any toner remaining on the drum
surface after the image transfers to the paper.
7) Quenching: The light from the quenching lamp neutralizes the charge
remaining on the drum.
G056/G058
6-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
6.3.2 LASER EXPOSURE
Overview
2
1
3
11
4
10
5
9
6
8
7
G058D201.WMF
1. LD unit
7. Synchronization detector
2. Laser shutter
8. Toroidal lens
3. Shield glass
9. 1st mirror
4. Polygon mirror
10. 2nd mirror
5. F-theta lens
11. Detector mirror
• Synchronization Detector: The beam emitted from the LD unit is reflected by the
1st mirror, 2nd mirror, and the detector mirror to the synchronizing detector.
• Two-beam Laser Writing: The LD unit writes two lines at once.
• LD Safety Shutter: When the front cover is opened, the shutter closes to block
the laser beam path.
• After the LD unit has been replaced, its position must be adjusted (see
Replacement and Adjustment).
• The thermistor next to the laser unit (not shown) checks the temperature inside
the machine. The machine automatically adjusts the charge roller and transfer
voltages in response to this temperature.
SM
6-7
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
6. Drum
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
Automatic Power Control (APC)
Engine Board
LD Drive Board
+5VLD
PD
ALOFF
LD
APD
ALD
Data
GAVD
BLOFF
LD
Control IC
PD
LD
BPD
DROPEN
BLD
VREF
Regulator
G056D503.WMF
• To prevent the intensity of the laser beam from changing because of
temperature, the machine monitors the laser beam with a photodiode (PD). The
PD passes the current to the LD control IC. The machine adjusts the current to
the laser diode by comparing it with the reference level from the regulator. The
LD control IC on the engine board controls this.
• The laser diode power is adjusted on the production line. Do not touch the
variable resistors on the LD unit in the field.
G056/G058
6-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
LD Safety Mechanisms
PSU
Engine Board
+24V
Front Cover SW
Rear Cover SW
LD Drive Board
Regulator
+5VLD
LD
Control IC
G056D504.WMF
Laser Safety Switch
When either of the covers are opened, the +5VLD power to the laser diodes is
interrupted.
Laser Shutter
The laser shutter [A] is a back-up safety
measure in case the switches are
defective and the +5VLD power reaches
the laser diodes.
[A]
The laser shutter cuts the laser beam
when the front cover is opened.
G058D202.WMF
SM
6-9
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
To ensure technician and user safety and to prevent the laser from inadvertently
switching on during servicing, there are safety switches on the front and rear
covers.
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
6.3.3 CARTRIDGE OVERVIEW
[A]
[B]
[C]
[J]
[I]
[H]
[G]
[F]
[E]
[D]
G058D113.WMF
[A]: Charge roller
[F]: Drum
[B]: Developer tank
[G]: Drum shutter
[C]: Toner tank
[H]: Waste toner tank
[D]: Reverse roller
[I]: Toner collection roller
[E]: Development roller
[J]: Cleaning blade
• This type of cartridge is known as an “All-in One” cartridge.
6.3.4 DRUM CHARGE
[B]
[A]: Charge roller
[B]: Cleaning pad
[A]
G058D511.WMF
• The charge roller gives the drum surface a negative charge of about
-900 V.
• The cleaning pad [A] contacts the charge roller to clean the surface.
G056/G058
6-10
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
6.3.5 DEVELOPMENT
Overview
[H]
[A]
[G]
[A]: Toner tank
[B]: Agitator
[C]: Pre-doctor blade
[D]: Development roller
[E]: Drum
[F]: Doctor blade
[G]: Reverse roller
[H]: Developer tank
[F]
[B]
[E]
[D]
[C]
G058D104.WMF
Toner Supply
• The agitator [B] stirs toner and carries it to the development roller.
Detailed
Descriptions
Development Unit
• This machine uses a single-roller development system.
• The high voltage supply applies -700V to the development roller.
• When the developer seal is removed, developer drops and the magnetic reverse
roller [G] stirs and mixes the developer.
• This machine does not use a TD sensor or ID sensor to control toner density.
• The toner density is controlled by the pre-doctor blade [C] and the doctor blade
[F].
SM
6-11
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
Toner Density Control
[A]
[A]
[B]
[B]
[C]
[C]
G058D121.WMF
G058D120.WMF
More toner is fed when the toner coating
on the development roller is thin
Less toner is fed when the toner coating
on the development roller is thick
[A]: Pre-doctor blade
[B]: Doctor blade
[C]: Circulation of developer
A mixture of toner and developer circulates at the pre-doctor blade [A].
• When the amount of toner on the development roller decreases, the circulation
[C] decreases to allow more toner to reach the development roller.
• When the amount of toner on the development roller increases, the circulation
[C] increases to allow only a little toner to reach the development roller.
Development Bias
Print Data:
White
Black
Toner
GND
Laser Exposed Area
-140V
Developmemt Roller
-700V
Drum Surface Voltage
-900V
G058D510.WMF
• Toner transfers from the development roller to the areas on the drum that were
exposed to the laser.
G056/G058
6-12
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
Toner End Detection
[A]
[B]
[A]: Toner tank
[B]: Toner end sensor
G058D115.WMF
• The toner end sensor detects toner near-end by the voltage output.
Toner near-end:
When the CPU detects that the output from the toner density sensor is below a
certain level, the machine warns the user by displaying “Low on Toner” on the
operation panel.
• To avoid waste toner tank overflow, the machine can also stop printing if the total
number of prints per cartridge exceeds a certain limit (default setting: 30k).
This number can be adjusted with “Waste Lim Count” in the engine service
mode.
SM
6-13
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
Toner end:
After toner near-end is detected, the machine can print 200 more pages, then it
disables printing. At this time, “Replace Toner Cartridge” is displayed. The 200page limit can be changed with engine service mode ("Toner End Count").
The machine also displays “Replace Toner Cartridge” when the output from the
toner density sensor is below a certain level.
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
6.3.6 IMAGE TRANSFER AND PAPER SEPARATION
Overview
[A]
[B]
[A]: Drum
[B]: Development roller
[C]: Transfer roller
[C]
G058D108.WMF
• This machine uses a transfer roller [C] to pull the toner from the drum onto the
paper.
• The high voltage supply applies a positive current (+18µA) to the transfer roller.
The current applied to the transfer roller can be adjusted with the printer engine
SP mode “Transfer set.”
[E]
[F]
[D]
[D]: Transfer roller
[E]: Separation plate
[F]: High voltage supply
G058D703.WMF
• The separation plate helps to separate paper from the drum.
Transfer Roller Cleaning
After a paper jam or when the wrong paper size was set, toner may transfer to the
back side of printouts. To prevent this, the machine automatically cleans the
transfer roller before the next print run.
During transfer roller cleaning, the high voltage supply applies a negative current
(-3µA) to the transfer roller.
The machine cleans the transfer roller under the following conditions.
• At power on
• During fusing unit warm-up
• Immediately after a jam has been cleared
• Any time the front cover is opened and closed
• After a job which is 10 pages or larger
G056/G058
6-14
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
6.3.7 CLEANING
[A]
[D]
[A]: Cleaning blade
[B]: Drum
[C]: Toner collection roller
[D]: Waste toner tank
[C]
[B]
G058D113.WMF
• The cleaning blade [A] removes any toner remaining on the drum.
• The toner collection roller [C] brings the toner into the waste toner tank.
• There is no waste toner overflow detection. See "Toner End Detection" for details
on avoiding waste tank overflow.
6.3.8 QUENCHING
[A]
[A]: Quenching lamp
[B]: Drum
G058D401.WMF
• Light from the quenching lamp (LED) reaches the drum through the slit at the top
of the cartridge.
SM
6-15
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
[B]
CÓPIA NÃO CONTROLADA
PRINTING PROCESS
6.3.9 ID CHIP
[B]
[A]
[A]: ID chip
[B]: Cartridge
G058D530.WMF
• An ID chip is installed in the cartridge which contains cartridge information.
G056/G058
6-16
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PAPER FEED
6.4 PAPER FEED
6.4.1 OVERVIEW
1
2
3
4
7
6
5
G058V112.WMF
1. Registration roller
5. Friction pad
2. Relay roller
6. Feed roller
3. By-pass feed roller
7. Paper tray
4. By-pass friction pad
Paper Feed System:
Feed roller and friction pad
Paper Lift Mechanism:
Tray arm and spring
Paper Detection:
Paper end sensor and paper near-end sensor
Paper Size Detection:
Paper size switch
Tray Capacity:
250 sheets
Tray Extension:
Available
By-pass Tray
Paper Feed System:
Feed roller and friction pad
Paper Lift Mechanism:
Cams and springs
Paper Detection:
By-pass tray paper sensor
Paper Size Detection:
None
Tray Capacity:
100 sheets
SM
6-17
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
Paper Tray
CÓPIA NÃO CONTROLADA
PAPER FEED
6.4.2 PAPER TRAY
Tray Extension
[A]
The tray can be extended manually to
hold paper longer than A4/Letter size. To
use longer paper, release the catches [A]
at both sides, then extend the tray and relock the catches.
The paper sizes in the following table can
be used.
[A]
G056D500.WMF
Tray Mode
Short (default)
Long
Possible Paper Sizes
A5 (LEF), B5 (LEF), A4 (LEF/SEF), 10.5”x7.25” (LEF),
LT (LEF/SEF)
B4 (SEF), A3 (SEF), 8.5”x13” (SEF), 8”x13” (SEF), 8.25”x13” (SEF), LG
(SEF), DLT (SEF)
Paper Lift
[C]
When the tray [A] is put in the machine,
the bottom plate [B] is lifted as follows.
• The slopes on the guide blocks [C] on
the machine lift the tray arms [D] up.
• The springs [E] between the tray arms
and bottom plates lift the plate.
• The springs [E] keep the stack of the
paper at the correct height.
• There is no height sensor.
[D]
[E]
[A]
[B]
G056/G058
6-18
CÓPIA NÃO CONTROLADA
G058D105.WMF
SM
CÓPIA NÃO CONTROLADA
PAPER FEED
Paper Feed and Registration
[H]
[B]
[D]
[A]
[A]: Feed roller
[B]: Registration roller
[C]: Paper feed clutch
[D]: Registration clutch
[E]: Friction pad
[F]: Registration sensor
[G]: Relay clutch
[H]: Relay roller
[F]
[G]
[E]
[C]
G058D102.WMF
Detailed
Descriptions
• The friction pad pressure cannot be adjusted.
• The machine makes a paper buckle at the registration roller to correct paper
skew.
The paper buckle can be adjusted by Engine Service Mode; Regist Sag.
SM
6-19
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PAPER FEED
Paper Size Detection
[B]
[A]
SW
Size
NA
DLT
LG
LT LEF
LT SEF
8.5”x13”
A4 LEF
∗
1
2
123
3
Eur/Asia
m
m
m
A3
m
l
l
A4 LEF
m
m
l
A4 SEF
l
m
m
A5 LEF
l
m
l
LT LEF
m
l
m
LT SEF
l
l
m
∗
l : On (Not pushed)
m : Off (Pushed)
[E]
[D]
[C]
G056D501.WMF
[A]: Paper size microswitches
[B]: Paper size dial
[C]: Bottom plate
[D]: Paper near-end sensor
[E]: Paper end sensor
• The machine disables paper feed from a tray if the paper size cannot be
detected (if the paper size actuator is broken or no tray is installed)
• When the paper size dial is at the “*” mark, the paper tray can be set up to
accommodate one of a wider range of paper sizes by using a User Tool at the
machine’s operation panel (Paper Input menu – Tray Paper Size).
Paper End/Paper Near-end Detection
Paper Near-end Detection
When about 50 sheets are left on the tray, the bottom plate [C] pushes up the
feeler of the paper near-end sensor [D]. The signal from the sensor is only used by
the host computer; there is no indication on the operation panel.
Paper End Detection
When the paper tray runs out of paper, the feeler of paper end sensor [E] drops
into the cutout in the bottom plate and the paper end sensor is activated.
G056/G058
6-20
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PAPER FEED
6.4.3 BY-PASS TRAY
[D]
[E]
[F]
[C]
[B]
[A]
[F]
G058D101.WMF
G058D103.WMF
Detailed
Descriptions
• The by-pass paper sensor [A] detects when paper is placed on the tray.
• The CPU energizes the by-pass feed solenoid [B], then the by-pass feed roller
[C] starts to feed paper to the registration roller [D] through the relay roller [E].
• The by-pass feed roller shaft has two cams [F]. These cams release the bottom
plate to press the stack of paper against the feed roller.
• There is no width sensor.
SM
6-21
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
IMAGE FUSING AND PAPER EXIT
6.5
IMAGE FUSING AND PAPER EXIT
6.5.1 OVERVIEW
1
2
3
10
4
9
8
5
6
7
G058D503.WMF
1. Paper exit roller
6. Hot roller
2. Hot roller strippers
7. Fusing pressure roller
3. Thermostat
8. Pressure spring
4. Thermistor
9. Fusing exit roller
5. Fusing lamp
10. Paper exit sensor
6.5.2 FUSING DRIVE
[A]
G058D504.WMF
• The main motor [A] drives the fusing unit through a gear train.
G056/G058
6-22
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IMAGE FUSING AND PAPER EXIT
6.5.3 FUSING ENTRANCE GUIDE SHIFT
[A]
G058R509.WMF
• The entrance guide [A] is adjustable for paper thickness to prevent creasing. The
outer-most screw holes on each side are the factory positions.
• If creasing occurs frequently in the fusing unit, change the entrance guide
position by securing it with the other holes. This allows paper to have more direct
access to the gap between the hot roller and the pressure roller.
6.5.4 PRESSURE ROLLER
Detailed
Descriptions
[A]
G058D505.WMF
• To change the applied pressure, adjust the position of the pressure springs. The
factory setting for the spring position is at the top (minimum pressure).
SM
6-23
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
IMAGE FUSING AND PAPER EXIT
6.5.5 NEW FUSING UNIT DETECTION
[A]
G058R512.WMF
There are two types of fusing unit: Service part, and maintenance kit part. Only the
fusing unit in the maintenance kit has this detection mechanism.
In the maintenance kit fusing unit, the looped wire on the fusing unit connector
contains a fuse [A]. When power is switched on after installing a new fusing unit,
the engine board detects the fusing unit through the looped wire as usual.
However, the fuse opens very shortly afterwards.
What happens next depends on the setting of Engine Service Mode - Meter
Service Charge:
- If Meter Charge Mode is enabled–
• After the technician replaces the fusing unit, the maintenance counter must
be reset with an SP mode (Engine Service Mode - PM Counter Reset).
- If Meter Charge Mode is disabled (default setting) • After the fusing unit has been replaced, the CPU detects the new unit and
automatically removes the “Replace Maintenance Kit” message. Then, the
maintenance counter resets automatically.
G056/G058
6-24
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IMAGE FUSING AND PAPER EXIT
6.5.6 FUSING TEMPERATURE CONTROL
(°C)
200
printing
168
standby
1 3 8 Ready to print
100
0
t
Main SW on
G056D502.WMF
When the main switch turns on, the CPU turns on the fusing lamp using the soft
start process (this prevents the room lights from flickering). The lamp stays on until
the thermistor detects the standby temperature. Then the CPU maintains this
temperature using on-off control. To start printing, the CPU raises the temperature
to the printing temperature.
Condition
Temperature
Ready to print
138 °C
Standby mode
168 °C
Print start ~
2 minutes
170 °C
180 °C
185 °C
170 °C
180 °C
185 °C
Printing
Tray
By-pass (Envelopes)
By-pass (Post Cards)
By-pass (Others)
Envelope Feeder
Thick Paper
2 min. ~
4 min.
165 °C
180 °C
185 °C
165 °C
180 °C
185 °C
Note
The machine can
start to print any
time.
On-off control
4 min ~
160 °C
180 °C
185 °C
160 °C
180 °C
185 °C
On-off control
To change between on/off control and phase control: Engine Service Mode Fusing control
SM
6-25
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
The fusing temperature for each mode is as follows.
CÓPIA NÃO CONTROLADA
IMAGE FUSING AND PAPER EXIT
Overheat protection
• If the hot roller temperature becomes greater than 240 °C, the CPU cuts off the
power to the fusing lamp. At this time, SC543 will be generated.
• If the thermistor overheat protection fails, there is a thermostat in series with the
common ground line of the fusing lamp. If the temperature of the thermostat
becomes greater than 210 °C, the thermostat opens, removing power from the
fusing lamp. At this time, the machine stops operation.
6.5.7 PAPER EXIT
[B]
[A]
[A]: Paper overflow detection sensor
[B]: Paper exit sensor
G058D601.WMF
• When the paper overflow detection sensor [A] is activated, the machine detects
that the paper stack height has exceeded a certain limit and stops printing.
• The paper exit sensor [B] detects paper misfeeds.
G056/G058
6-26
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IMAGE FUSING AND PAPER EXIT
6.5.8 ENERGY SAVER MODE
When the machine is not being used, the energy saver feature reduces power
consumption by switching off the fusing lamp.
Entering Energy Saver Mode
Energy saver mode starts after the machine has been idle for a certain time. This
time is specified by the user; the following choices are available (press the Menu
key on the operation panel, and access the System menu).
• Off (energy saver mode never activates)
• 5 minutes
• 15 minutes
• 30 minutes (default)
• 60 minutes
When the machine is in energy saver mode, the CPU turns off the fusing lamp.
However, the +24V, +12V, and +5V lines are still active.
Leaving Energy Saver Mode
Detailed
Descriptions
The machine leaves energy saver mode when one of the following happens.
• Print command received from the PC
• Any cover opened and closed
• Any operation panel keys pressed
SM
6-27
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CONTROLLER FUNCTIONS
6.6 CONTROLLER FUNCTIONS
6.6.1 METER-CHARGE MODE
Meter-charge Counter Display
When the meter-charge mode (printer engine service mode) is switched on, the
meter-charge counter menu is the first item shown on the user menu.
(The “Sample Print” menu appears first when the meter- Menu:
charge mode is switched off.)
Counter
PM Warning Display
When the meter-charge mode (printer engine service mode) is switched on,
“Replace Maintenance Kit” will not be displayed at 90k prints.
NOTE: The default setting for this machine is meter-charge mode off.
Item
Meter-charge
counter
PM Warning
Meter-charge On
Shown as the first
item in the user menu
Not shown
PM
PM Counter
Service
Reset manually
Meter-charge Off
Not shown
“Replace Maintenance
Kit” displayed at 90k
prints
Customer
Automatically reset
when the fusing unit is
replaced using the
maintenance kit
Remarks
User menu
Printer engine
service mode “PM
counter”
The meter-charge counter is not the same as the PM counter. This is because, in
the following cases, the meter-charge counter does not count up.
• Blank rear side during duplex printing
• Blank page when using the “Cover Page” or “Two in One” features
• Service reports
NOTE: The meter-charge counter cannot be reset.
6.6.2 SAMPLE PRINT
This feature is formally known as “Proof Print”. This function gives users a chance
to check the print results before starting a multiple-set print run.
• The size of the hard disk partition for the sample print feature is 5.4 GB. This
partition is also used by the collation and locked print features.
• The partition can hold up to 30 files, including files stored using locked print.
• The maximum number of pages is 1,000, including jobs using locked print and
collation.
NOTE: Sample print requires the installation of an optional hard disk.
G056/G058
6-28
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
CONTROLLER FUNCTIONS
6.6.3 LOCKED PRINT
Using this feature, the print job is stored in the machine but will not be printed until
the user inputs an ID at the machine’s operation panel. This ID must match the ID
that was input with the printer driver.
• Stored data is automatically deleted after it is printed.
• Stored data can be manually deleted at the operation panel.
• The hard disk can hold up to 30 files, including files stored using sample print.
• The maximum number of pages is 1,000, including jobs using sample print and
collation.
• Locked print uses the same hard disk partition as sample print and collation,
which is 5.4 GB.
NOTE: Locked print requires the installation of an optional hard disk.
6.6.4 PAPER SOURCE SELECTION
Tray Priority (Auto Tray Select)
The Tray Priority setting determines the start
of the tray search when the user selects
“Auto Tray Select” with the driver.
The machine searches for a paper tray with
the specified paper size and type.
Priority Tray
Start of Tray Search
Tray 1
Tray 2 (Optional)
The Tray Priority setting can be specified
using the Paper Input menu of the user tools.
Tray 3 (Optional)
Bypass Feed
G058D521.WMF
Tray Lock
If Tray Lock is enabled for a tray, the controller skips the “locked” tray in the tray
search process.
NOTE: In this machine, each paper source can be “locked”, including the by-pass
feeder. If all paper sources are locked and “Auto Tray Select” is specified
from the driver, the machine displays an error and stops printing.
Manual Tray Select
If the selected tray does not have the paper size and type specified by the driver,
the controller stops printing until the user loads the correct paper.
SM
6-29
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
When no tray contains paper that matches
the paper size and type specified by the
driver, the controller stops printing until the
user loads the correct paper.
CÓPIA NÃO CONTROLADA
CONTROLLER FUNCTIONS
6.6.5 AUTO CONTINUE
When this function is enabled, the machine continues printing even if there is no
paper tray which matches the paper size and paper type specified by the driver.
The machine searches for a paper tray in the following way.
NOTE: The default setting for this feature is 'disabled'.
Auto Tray Select
When there is no paper tray that matches the
paper size and type specified by the driver,
the machine searches for any tray that has
paper, and prints from the first tray it finds.
The start of the tray search is the tray
selected as the “Priority Tray.”
Priority Tray
Start of Tray Search
Tray 1
Tray 2 (Optional)
Tray 3 (Optional)
Bypass Feed
G058D521.WMF
Manual Tray Select
The machine prints from the selected tray even if the paper size and type do not
match the setting specified from the driver.
G056/G058
6-30
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
CONTROLLER FUNCTIONS
6.6.6 PAPER OUTPUT TRAY
The output tray can be selected using the “System” menu of the user tools. To
select an output tray other than the standard tray, the one-bin shift tray or four-bin
mailbox must be installed.
Output Tray Selected
• If the machine cannot print to the selected output tray, it prints to the standard
tray.
• If paper overflow is detected at the selected output tray, the controller stops
printing until the overflow detector goes off.
Auto Tray Switching
When “Auto Tray SW” is selected in the “System” menu of the user tools and
“Printer Default” is specified as an output tray in the driver, the controller
automatically sends the output to the lowest tray. When that tray fills up, the
controller sends the output to the next lowest tray.
4th tray
3rd tray
2nd tray
1st tray
G058D522.WMF
• If a tray becomes full and paper is detected in the next tray, the machine displays
an error and stops printing.
• If all trays become full (overflow detected in all trays), the machine displays an
error and stops printing. This time, all paper must be removed.
SM
6-31
CÓPIA NÃO CONTROLADA
G056/G058
Detailed
Descriptions
Standard Tray
CÓPIA NÃO CONTROLADA
NIB
6.7 NIB
6.7.1 BLOCK DIAGRAM
CN2
NIB I/F (CN6)
Controller Board
Flash ROM
4MB
EEPROM
PHY
DP83846
Oscillator
Filter Module
NIB
LED
LED
RJ45
Network
G056D505.WMF
• The Flash ROM contains the NIB firmware. The firmware can be upgraded using
an Flash ROM card connected to the controller board.
6.7.2 LED INDICATORS
LED2 (Yellow)
LED1 (Green)
G056D506.WMF
Description
LED1 (Green): Link status
LED2 (Yellow): Data rate
G056/G058
On
Link success
100 Mbps
Off
Link failure
10 Mbps
6-32
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IEEE1394 INTERFACE
6.8 IEEE1394 INTERFACE
6.8.1 SPECIFICATIONS
Hardware Specification
Interface: IEEE1394 (6 pins)
(non-power supply, cable power repeated-IEEE1394a-2000 compliant)
Ports:
2 ports
Data rates: 400Mbps/200Mbps/100Mbps
System Requirements
PC:
IBM PC/AT with IEEE1394 port
OS:
MS Windows 2000 upgraded with service pack 1
Cable length: 4.5m (15ft)
6.8.2 IEEE1394
IEEE1394, also known as FireWire (a name patented by Apple), is an easy-to-use
peer-to-peer networking technology allowing speeds of up to 400 Mbps.
Detailed
Descriptions
The current standard contains the following features, which are supported in most
devices:
• Hot swapping (cables can be connected and disconnected while the
computer and other devices are switched on)
• Peer-to-peer networking (no hub required)
• No terminator or device ID is required, unlike SCSI
• Automatic configuration of devices upon start-up, or “plug and play.”
• Real-time data transfer at 100, 200, and 400 Mbps
• Common connectors for different devices
1394 I/F
1394 I/F
G056D513.WMF
The cable length is limited to 4.5 m (15ft). However, up to 16 cables and 63
devices can be connected to an IEEE1394 network.
IEEE1394 cables can be either 4-pin (data only) or 6-pin (data and power).
IEEE1394 allows either 6-pin or 4-pin connectors. However, this machine only uses
the 6-pin connectors. The machine has two 6-pin ports.
SM
6-33
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
IEEE1394 INTERFACE
6.8.3 BLOCK DIAGRAM
Clock
Oscillator
EEPROM
PHY
TSB41AB2
Link
TSB12LV23A
Option I/F (CN4)
IEEE1394 Board
1394 I/F
PC
1394 I/F
Controller Board
G056D508.WMF
• PHY: Physical layer control device
• Link: Link layer control device
• EEPROM: 256-byte ROM
6.8.4 PIN ASSIGNMENT
Pin assignment
Pin 1
Pin 2
Pin 5
Pin 1
Pin 4
Pin 3
Pin 6
Pin 6
G056D514.WMF
Pin
No.
1
2
3
4
5
6
Signal Description
Cable Power
GND
Receive strobe
Transmit data
Receive data
Transmit strobe
G056/G058
6-34
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IEEE1394 INTERFACE
6.8.5 REMARKS ABOUT THIS INTERFACE KIT
Note the following points about this unit.
• The machine does not print reports specifically for IEEE1394. Just print the
Configuration Page at installation to check that the machine recognizes the card.
• There is no spooler or print queue. If a computer tries to print over the IEEE1394
while the printer is busy, the IEEE1394 interface card inside the printer will return
a busy signal.
• After starting a job using IEEE1394, do not switch the printer off until the job has
been completed. Even though the printer may appear to be dead, it may be in
the middle of an IEEE1394 protocol exchange with the computer.
• When using IEEE1394, it is not possible to check the printer status from the
computer with a utility such as Printer Manager for Client.
6.8.6 TROUBLESHOOTING NOTES
Detailed
Descriptions
If there are problems printing using the IEEE1394 interface, check the following.
• Is the computer using Windows 2000 with service pack 1?
• Has the interface card been replaced recently? Each card has an individual
address, similar to the MAC address in an Ethernet card. If the card was
changed, the driver cannot find the old card. The new card is another device and
a new printer appears in Windows Control panel, and this must be configured in
the same way as the printer that was replaced (the old printer icon in Windows
Control Panel should be deleted) has to be reconfigured.
• Is there a loop somewhere in the network? An IEEE1394 network must be a
chain or a branched chain. There can be no loops.
• Try to find out where in the chain the problem is occurring. Test the machine
one-to-one with the computer to determine if the printer is defective (when the
printer’s interface cable is plugged in, the computer should see ‘Printer Ready’;
when the cable is disconnected, the computer should see ‘Offline’).
SM
6-35
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
GENERAL SPECIFICATIONS
7.1
SPECIFICATIONS
GENERAL SPECIFICATIONS
Printing Speed:
Maximum 26 pages per minute (A4/LT LEF)
(20 pages: duplex printing)
Printer Languages:
PCL6/PCL5e
PostScript 3
RPCS (Refined Printing Command Stream: an original Ricoh
PDL)
TIFF (rev 6.0 compatible)
Resolution:
1200 dpi (PCL6/PS3/RPCS)
600 dpi (PCL 6/PCL5e/PS3/RPCS)
300 dpi (PCL 5e/PS3)
Resident Fonts:
PCL:
35 Intellifonts
10 True Type fonts
PS3:
136 fonts (24 Type 2 fonts, 112 Type 14 fonts)
Host Interfaces:
Bi-directional IEEE1284 parallel x 1: Standard
Ethernet (100 Base-TX/10 Base-T): Standard for G058
IEEE1394: Optional for G056 (G058: Must remove NIB)
Network Protocols:
TCP/IP, IPX/SPX, NetBEUI, Apple Talk
First Print Speed:
6.5 s or less (A4/LT LEF, standard tray)
Warm-up Time
Less than 12 seconds
(Less than 19 seconds from power on)
Print Paper
Capacity:
Standard tray: 250 sheets
Optional paper tray unit: 500 sheets
(up to two paper tray units can be installed)
Optional by-pass tray: 100 sheets
Print Paper Size:
Maximum: A3/11" x 17"
Minimum:
Standard tray:
A5 LEF
Optional paper tray: A5 LEF
By-pass: A6/ 90 x 148 mm SEF
(Refer to "Supported Paper Sizes".)
60 to 105 g/m2 (16 to 28 lb.)
60 to 105 g/m2 (16 to 28 lb.)
52 to 162 g/m2 (14 to 43 lb.)
Printing Paper
Weight:
Standard tray:
Optional paper tray:
By-pass tray:
Output Paper
Capacity:
Standard output tray: 250 sheets
Optional 1-bin shift tray: 250 sheets
Optional 4-bin mailbox: 200 sheets total
SM
7-1
CÓPIA NÃO CONTROLADA
G056/G058
Specifications
7
CÓPIA NÃO CONTROLADA
GENERAL SPECIFICATIONS
Memory:
Standard 32 MB, up to 96 MB with optional DIMM
Power Source:
120 V, 60 Hz: More than 10 A (for North America)
220 V - 240 V, 50/60 Hz: More than 6.0 A (for Europe)
Power Consumption:
120V
940 W or less
650 W or less
22 W or less
230V
940 W or less
650 W or less
22 W or less
Mainframe Only
Full System
64 dB or less
40 dB or less
68 dB or less
40 dB or less
Maximum
Printing
Energy Saver
Noise Emission:
Printing
Stand-by
NOTE: The above measurements were made in accordance with ISO 9296 at
the operator position.
Dimensions (W x D x H): 468 x 437 x 305 mm
Weight:
G056/G058
Less than 18 kg
7-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
GENERAL SPECIFICATIONS
Paper
Size (W x L)
A3
B4
A4 SEF
A4 LEF
B5 SEF
B5 LEF
A5 SEF
A5 LEF
B6 SEF
B6 LEF
A6 SEF
Ledger
Legal
Letter SEF
Letter LEF
Half Letter SEF
Half Letter LEF
Executive SEF
Executive LEF
F
Foolscap
Folio
Com10 Env.
Monarch Env.
C6 Env.
C5 Env.
DL Env.
8K
16K SEF
16K LEF
Custom
297 x 420 mm
257 x 364 mm
210 x 297 mm
297 x 210 mm
182 x 257 mm
257 x 182 mm
148 x 210 mm
210 x 148 mm
128 x 182 mm
182 x 128 mm
105 x 148 mm
11 x 17”
8.5 x 14“
8.5 x 11”
11 x 8.5”
5.5 x 8.5”
8.5 x 5.5”
7.25 x 10.5”
10.5 x 7.25”
8 x 13”
8.5 x 13”
8.25 x 13”
4.125 x 9.5”
3.875 x 7.5”
114 x 162 mm
162 x 229 mm
110 x 220 mm
267 x 390 mm
195 x 267 mm
267 x 195 mm
Minimum:
90 x 148 mm
Maximum:
297 x 432 mm
Paper Trays
Main Unit/Option
US
Eur/Asia
# #
Y /Y
Y/Y
# #
# #
Y /Y
Y /Y
# #
Y /Y
Y/Y
Y/Y
Y/Y
# #
# #
Y /Y
Y /Y
# #
# #
Y /Y
Y /Y
N
N
# #
#
Y /Y
Y/Y
N
N
N
N
N
N
# #
Y/Y
Y /Y
# #
Y/Y
Y /Y
Y/Y
Y/Y
Y/Y
Y/Y
N
N
N
N
#
#
N/Y
N/Y
# #
# #
Y /Y
Y /Y
# #
# #
Y /Y
Y /Y
#
# #
Y/Y
Y /Y
# #
# #
Y /Y
Y /Y
N
N
N
N
N
N
N
N
N
N
#
#
N/Y
N/Y
#
#
N/Y
N/Y
#
#
N/Y
N/Y
C
N/Y
By-pass
Tray
C
N/Y
Env.
Feeder
Duplex
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
C
Y
N
C
Y
#
Y
#
Y
#
Y
#
Y
#
Y
N
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
#
Y
#
Y
#
Y
#
Y
#
Y
N
N
N
Y
Y
Y
Y
Y
Y
N
Y
N
N
N
Y
Y
Y
Y
N
N
N
Y
Y
Y
Y
N
N
N
N
N
Y
Y
Y
C
N
N
Y
Remarks:
Y
Y#
YC
N
SM
Supported. The paper size sensor detects the paper size.
Supported. The user has to select the correct paper size for the tray.
Supported. The user has to enter the width and length of the paper.
Not supported.
7-3
CÓPIA NÃO CONTROLADA
G056/G058
Specifications
7.1.1 SUPPORTED PAPER SIZES
CÓPIA NÃO CONTROLADA
SOFTWARE ACCESSORIES
7.2 SOFTWARE ACCESSORIES
The printer drivers and utility software are provided on one CD-ROM. An auto-run
installer allows you to select which components to install.
7.2.1 PRINTER DRIVERS
Printer Language
PCL 6
PCL 5e
PS3
RPCS
Windows
95/98/ME
Yes
Yes
Yes
Yes
Windows NT4.0 Windows 2000
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Macintosh
No
No
Yes
No
NOTE: 1) The printer drivers for Windows NT 4.0 are only for the Intel x86
platform. There is no Windows NT 4.0 printer driver for the PowerPC,
Alpha, or MIPS platforms.
2) The PS3 drivers are all genuine AdobePS drivers, except for Windows
2000, which uses Microsoft PS. A PPD file for each operating system is
provided with the driver.
3) The PS3 driver for Macintosh supports Mac OS 7.6 or later versions.
7.2.2 UTILITY SOFTWARE
Software
Agfa Font Manager
(Win3.1x, 95/98, NT4)
Aficio Manager for Admin
(Win 95/98, NT4)
Aficio Manager for Client
(Win95/98, NT4)
Multidirect Print
(Win95/98, 2000, NT4, )
Port Navi
(Win95/98, 2000, NT4)
Printer Utility for Mac
G056/G058
Description
A font management utility with screen fonts for the printer.
A printer management utility for network administrators. NIB
setup utilities are also available.
A printer management utility for client users.
A utility for peer-to-peer printing over a NetBEUI or TCP/IP
network.
A peer to peer print utility over a TCP/IP network. This provides
the parallel printing and recovery printing features.
This software provides several convenient functions for printing
from Macintosh clients.
7-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
MACHINE CONFIGURATION
7.3
MACHINE CONFIGURATION
7.3.1 SYSTEM COMPONENTS
[D]
[C]
[B]
[A]
[E]
G058V107.WMF
Machine Code
G058
G056
No.
Option
Duplex Unit
4-bin Mailbox
1-bin Shift Tray
Paper Tray Unit
G552
G553
G554
G555
B
C
D
E
Envelope Feeder
G556
E
Internal Option
NIB
G573
IEEE1394
G561
HDD
Memory 64 MB
Others
Maintenance Kit
G575
G579
Main Unit
A
Remarks
G058: Includes the NIB as standard
Up to two tray units can be installed.
When two paper tray units are
installed, it must be installed in the
upper unit.
Standard component for G058
To install in the G058, remove the
NIB first.
G770
NOTE: 1) All the above items are user installable.
2) The NIB and the IEEE1394 board cannot be installed at the same time.
To install the IEEE1394 in the G058, remove the NIB first.
SM
7-5
CÓPIA NÃO CONTROLADA
G056/G058
Specifications
Item
CÓPIA NÃO CONTROLADA
OPTIONAL EQUIPMENT
7.4
OPTIONAL EQUIPMENT
7.4.1 PAPER TRAY UNIT
Print Paper Size:
Maximum:
Minimum:
A3/11” x 17”
A5 LEF
Print Paper Weight:
60 to 105 g/m2 (16 to 28 lb.)
Tray Capacity:
500 sheets (80 g/m2, 20 lb.)
Two units can be installed.
Paper Feed System:
Feed roller and friction pad
Paper Height Detection:
4 steps (100%, 90%, 50%, 10%)
Power Source:
DC 24V, 5V (from the main unit)
Power Consumption:
15 W
Dimensions (W x D x H):
468 x 410 x 130 mm
Weight
5.6 kg
7.4.2 ENVELOPE FEEDER
Print Paper Size:
Com#10, Monarch, C6, DL, C5
Tray Capacity:
60, or up to the level of the maximum stack indication
(52 mm)
Paper Feed System:
Feed roller and friction pad
Paper Height Detection:
None
Weight
1.9 kg
7.4.3 DUPLEX UNIT
Print Paper Size:
Maximum:
Minimum:
Print Paper Weight:
64 to 105 g/m2 (18 to 28 lb.)
Paper Capacity:
1 sheet
Power Source:
DC 24V, 5V (from the main unit)
Power Consumption:
35 W
Dimensions (W x D x H):
419 x 115 x 257 mm (when installed in the machine)
Weight
6 kg
G056/G058
A3/11" x 17"
A5 SEF
7-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
OPTIONAL EQUIPMENT
7.4.4 FOUR-BIN MAILBOX
Number of Trays
4 trays
Tray Capacity:
50 sheets (80 g/m2, 20 lb.)
Paper Size for Trays:
Maximum:
Minimum:
Print Paper Weight:
60 to 105 g/m2 (16 to 28 lb.)
Power Source:
DC 24V, 5V (from the main unit)
Power Consumption:
15 W
Dimensions (W x D x H):
462 x 391 x 285 mm (when installed in the machine)
Weight
5.3 kg
A3/11" x 17"
A5 LEF
7.4.5 ONE-BIN SHIFT TRAY
Maximum:
Minimum:
A3/11" x 17"
A5 LEF
Print Paper Weight:
60 to 105 g/m2 (16 to 28 lb.)
Tray Capacity:
250 sheets (80 g/m2, 20 lb.)
Power Source:
DC 24V, 5V (from the main unit)
Power Consumption:
12 W
Dimensions (W x D x H):
462 x 393 x 160 mm (when installed in the machine)
Weight
2.6 kg
Specifications
Print Paper Size:
SM
7-7
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
G555
PAPER TRAY UNIT
G556
ENVELOPE FEEDER
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
PAPER FEED UNIT
1. REPLACEMENT AND ADJUSTMENT
!CAUTION
Turn off the main power switch and unplug the machine before attempting
any of the procedures in this section.
NOTE: This manual uses several symbols. The meanings of those symbols are as
follows:
☛: See or Refer to
!: screw
": connector
1.1 PAPER FEED UNIT
[A]
G555R101.WMF
Paper Tray
G555
Envelope
Feeder G556
• Remove the paper tray unit from the main unit.
• Draw out the paper tray.
[A]: Remove the paper feed unit ( ! x5).
SM
8-1
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
PAPER FEED ROLLER
1.2 PAPER FEED ROLLER
[B]
G555R103.WMF
[A]
• Draw out the paper tray
[A]: Paper feed roller (move the lever [B] to the left)
1.3 FRICTION PAD
[A]
G555R102.WMF
• Draw out the paper tray.
[A]: Friction pad
G056/G058
8-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
2. DETAILED DESCRIPTIONS
2.1 OVERALL MACHINE INFORMATION
2.1.1 MECHANICAL COMPONENT LAYOUT
1
2
G555D105.WMF
1. Paper feed roller
3
2. Friction pad
3. Bottom plate
2.1.2 ELECTRICAL COMPONENT LAYOUT
2
1
5
4
1. Paper tray board
7
G555V101.WMF
6
5. Paper end sensor
2. Paper feed clutch
6. Paper feed sensor
3. Paper feed motor
7. Paper height sensor
4. Paper size switch
8. Paper height sensor
3
SM
8-3
CÓPIA NÃO CONTROLADA
Paper Tray
G555
Envelope
F d G556
8
G056/G058
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
2.2
DETAILED SECTION DESCRIPTIONS
2.2.1 PAPER FEED AND SEPARATION
[D]
[A]
[C]
[B]
G555D104.WMF
• The paper tray holds 500 sheets.
• The paper feed unit uses a feed roller and friction pad mechanism.
[A]: Paper feed roller
[B]: Friction pad
[C]: Pressure spring
[D]: Paper feed sensor
G056/G058
8-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
2.2.2 PAPER LIFT
Paper lift is the same as for the main unit.
2.2.3 PAPER END DETECTION
[A]
G555D103.WMF
Paper Tray
G555
Envelope
F d G556
• When the paper tray runs out of paper, the feeler [A] drops into the cutout in the
bottom plate to actuate the paper end sensor.
SM
8-5
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
2.2.4 PAPER HEIGHT DETECTION
• The paper height is detected by the combination of the paper height sensor
signals. The signals from the sensors indicate whether there are 450, 250, or 50
sheets remaining.
450 sheets
(90%)
500 sheets
(100%)
50 sheets
(10%)
250 sheets
(50%)
G555D106.WMF
Amount of paper
50 sheets
250 sheets
450 sheets
500 sheets
Paper height
sensor 1
OFF
OFF
ON
ON
Paper height
sensor 2
OFF
ON
ON
OFF
OFF: Unblocked, ON: Blocked
G056/G058
8-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
2.2.5 PAPER SIZE DETECTION
SW
Size
A3
A4 LEF (Long Edge Feed)
A4 SEF (Short Edge Feed)
81/2" x 11" LEF
11” x 17”
14” x 81/2" SEF
11" x 81/2" SEF
* (Asterisk)
1
2
3
4
l
l
l
l
l
l
l
l
l
l
l
m
m
m
l
m
l
m
l
m
l
l
m
m
l
m
m
l
l
m
l
m
[A]
[B]
m : ON (Not pushed)
l : OFF (Pushed)
G555D102.WMF
[A]: Paper size switch
[B]: Paper size dial
Paper Tray
G555
Envelope
F d G556
• The machine disables paper feed from a tray if the paper size cannot be
detected (if the paper size actuator is broken or no tray is installed)
• When the paper size dial is at the “*” mark, the paper tray can be set up to
accommodate one of a wider range of paper sizes by using a User Tool at the
machine’s operation panel (Paper Input menu – Tray Paper Size).
SM
8-7
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
3. ENVELOPE FEEDER
3.1 OVERALL MACHINE INFORMATION
3.1.1 MECHANICAL COMPONENT LAYOUT
• This optional unit is a tray that slides into the optional paper feed unit, replacing
the paper tray.
• If two optional trays have been installed, the envelope feeder must go into the
top tray.
• The layout is the same as the paper tray.
• The friction pad in this unit is rubber-coated. The friction pad in the paper tray
unit is made of cork.
G056/G058
8-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
G552
DUPLEX UNIT
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
1. REPLACEMENT AND ADJUSTMENT
!CAUTION
Turn off the main power switch and unplug the machine before attempting
any of the procedures in this section.
NOTE: This manual uses several symbols. The meanings of those symbols are as
follows:
☛: See or Refer to
!: screw
": connector
1.1 EXTERIOR COVERS
[B]
[A]
[C]
G552R101.WMF
[D]
G552R102.WMF
• Remove the duplex unit from the main unit.
• Open the upper cover [A].
[A]:
[B]:
[C]:
[D]:
SM
Upper cover (! x2)
Right cover (! x2)
Left cover (! x1)
Front cover (! x2)
9-1
CÓPIA NÃO CONTROLADA
G056/G058
Duplex Unit
G552
EXTERIOR COVERS
CÓPIA NÃO CONTROLADA
DUPLEX BOARD AND SENSORS
1.2 DUPLEX BOARD AND SENSORS
[B]
[D]
[A]
[C]
G552R103.WMF
G552R104.WMF
[E]
G552R105.WMF
• Front cover (☛ Exterior Covers)
[A]:
[B]:
[C]:
[D]:
[E]:
Duplex board bracket (! x2)
Duplex board (! x2, all connectors)
Inverter sensor (" x1)
Entrance sensor (" x1)
Exit sensor (" x1)
G056/G058
9-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
Duplex Unit
G552
2. DETAILED DESCRIPTION
2.1 OVERALL MACHINE INFORMATION
2.1.1 MECHANICAL COMPONENT LAYOUT
2
1
4
3
6
G552V101.WMF
5
1. Junction gate
2. Entrance sensor
3. Inverter rollers
4. Transport rollers
5. Transport sensor
6. Exit sensor
SM
9-3
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
Rev. 12/2003
2.1.2 DRIVE LAYOUT
3
1
2
4
G552V103.WMF
G552V105.WMF
1. Inverter motor
2. Inverter rollers
3. Transport motor
4. Transport rollers
2.1.3 ELECTRICAL COMPONENT LAYOUT
1
2
1. Entrance sensor
3
7
2. Duplex board
3. Inverter motor
6
4. Junction gate solenoid
⇒ 5.
⇒ 6.
Inverter sensor
Exit sensor
7. Transport motor
4
5
G552
9-4
CÓPIA NÃO CONTROLADA
G552V104.WMF
SM
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
DETAILED SECTION DESCRIPTIONS
Duplex Unit
G552
2.2
2.2.1 BASIC OPERATION
Longer than A4 LEF/LT LEF
• The duplex unit can store only one sheet of paper.
Example: 8 pages. The center number in the illustration shows the order of pages.
The number with the circle in the illustration shows the order of sheets of
print paper (if highlighted, this indicates the second side).
1
➀
2
)
3
➁
4
$
5
➂
6
%
7
➃
8
'
G552I500.WMF
G552D106.WMF
SM
9-5
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
Length up to A4 LEF/LT LEF
• The duplex unit can store three sheets of paper
Example: 8 pages. The center number in the illustration shows the order of pages.
The number with the circle in the illustration shows the order of sheets of
print paper (if highlighted, this indicates the second side).
1
➀
3
➁
5
➂
2
)
7
➃
4
$
6
%
8
*
G552I501.WMF
G552D107.WMF
G056/G058
9-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
Duplex Unit
G552
2.2.2 FEED IN AND EXIT MECHANISM
[B]
[C]
[A]
[E]
[D]
[F]
[G]
G552V102.WMF
Feeding paper into the duplex unit:
• The junction gate solenoid [A] turns on to open the junction gate [B].
• The paper fed from the main frame is sent to the inverter section [C].
Inversion and exit:
• After the trailing edge of the paper passes the inverter sensor [D], the inverter
roller [E] changes its rotation direction and the paper goes to the transport area
[F].
• The transport rollers [G] send the paper to the registration rollers in the main
frame.
SM
9-7
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
G553
FOUR-BIN MAILBOX
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
EXTERIOR COVERS
1. REPLACEMENT AND ADJUSTMENT
!CAUTION
NOTE: This manual uses several symbols. The meanings of those symbols are as
follows:
☛: See or Refer to
!: screw
": connector
1.1 EXTERIOR COVERS
[D]
[C]
[B]
[A]
G553R101.WMF
[A]:
[B]:
[C]:
[D]:
SM
Each tray
Right cover (! x1)
Left cover (! x1)
Upper cover
10-1
CÓPIA NÃO CONTROLADA
G056/G058
Four-Bin
Mailbox
G553
Turn off the main power switch and unplug the machine before attempting
any of the procedures in this section.
CÓPIA NÃO CONTROLADA
OVERFLOW AND VERTICAL TRANSPORT SENSORS
1.2 OVERFLOW AND VERTICAL TRANSPORT SENSORS
[A]
G553R102.WMF
[E]
[C]
[B]
[D]
G553R103.WMF
• Each tray (☛ Exterior Covers)
[A]:
[B]:
[C]:
[D]:
[E]:
Each tray cover
Sensor holder (! x1)
Tray paper sensor (" x1)
Overflow sensor (" x1)
Vertical transport sensor (" x1)
G056/G058
10-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
MAIN MOTOR
1.3 MAIN MOTOR
Four-Bin
Mailbox
G553
[B]
[C]
[A]
G553R104.WMF
• Left cover (☛ Exterior Covers)
[A]: Mailbox board (! x2, " x11)
[B]: Drive bracket (! x5)
[C]: Main motor (! x2)
SM
10-3
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
2. DETAILED DESCRIPTIONS
2.1 OVERALL MACHINE INFORMATION
2.1.1 MECHANICAL COMPONENT LAYOUT
1
7
2
3
6
4
5
G553V101.WMF
1. 4th tray
5. Vertical transport roller
2. 3rd tray
6. Turn gate
3. 2nd tray
7. Exit roller
4. 1st tray
G056/G058
10-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
2.1.2 DRIVE LAYOUT
3
2
Four-Bin
Mailbox
G553
1
G553V102.WMF
1. Timing belt
2. Main motor
3. Main motor timing belt
SM
10-5
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
2.1.3 ELECTRICAL COMPONENT LAYOUT
4
3
2
5
6
7
8
1
9
17
10
16
11
12
13
14
15
G553V103.WMF
1. 2nd turn gate solenoid
10. Upper vertical transport sensor
2. Main motor
11. 2nd tray overflow sensor
3. 3rd turn gate solenoid
12. 1st tray paper sensor
4. Cover sensor
13. 1st tray overflow sensor
5. 4th tray paper sensor
14. Lower vertical transport sensor
6. 3rd tray paper sensor
15. Junction gate solenoid
7. 4th tray overflow sensor
16. 1st turn gate solenoid
8. 2nd tray paper sensor
17. Mailbox board
9. 3rd tray overflow sensor
G056/G058
10-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
2.2
DETAILED SECTION DESCRIPTIONS
2.2.1 BASIC OPERATION
Four-Bin
Mailbox
G553
[B]
G553D101.WMF
[A]
G553V105.WMF
• When the leading edge of the paper activates the exit sensor on the main unit,
the mailbox main motor turns on.
• Each turn gate solenoid [A] opens and closes its turn gate, to direct the paper to
the selected tray [B].
• When the top tray (4th tray) is selected, none of the solenoids are activated.
• After the last sheet passes the upper or lower vertical transport sensor
(depending on the selected tray), the main motor, junction gate solenoid, and
the turn gate solenoid for the selected tray turn off.
SM
10-7
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
G554
ONE-BIN SHIFT TRAY
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
EXTERIOR COVERS
1. REPLACEMENT AND ADJUSTMENT
!CAUTION
Turn off the main power switch and unplug the machine before attempting
any of the procedures in this section.
NOTE: This manual uses several symbols. The meanings of those symbols are as
follows:
One-Bin Shift
Tray G554
☛: See or Refer to
!: screw
": connector
1.1 EXTERIOR COVERS
[D]
[C]
[A]:
[B]:
[C]:
[D]:
Tray
Right cover (! x1)
Left cover (! x1)
Upper cover (1 snap-ring)
[A]
G554R101.WMF
SM
11-1
CÓPIA NÃO CONTROLADA
[B]
G056/G058
CÓPIA NÃO CONTROLADA
SHIFT TIMING AND TRAY PAPER SENSORS
1.2 SHIFT TIMING AND TRAY PAPER SENSORS
[B]
[C]
[A]
G554R102.WMF
G554R103.WMF
Right cover (☛ Exterior Covers)
[A]: Tray cover
[B]: Shift timing sensor (" x1)
[C]: Tray paper sensor (" x1)
1.3 COVER AND OVERFLOW SENSORS
[B]
[A]
[A]: Sensor cover
[B]: Cover sensor (" x1)
[C]: Overflow sensor (" x1)
[C]
G554R104.WMF
G056/G058
11-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
MAIN MOTOR
1.4 MAIN MOTOR
[B]
[D]
[A]
G554R106.WMF
G554R105.WMF
Left cover (☛ Exterior Covers)
[A]: Shift tray board (! x2, " x6)
[B]: Junction gate solenoid (! x2)
[C]: Main motor bracket (! x3)
[D]: Main motor (! x2)
SM
11-3
CÓPIA NÃO CONTROLADA
G056/G058
One-Bin Shift
Tray G554
[C]
CÓPIA NÃO CONTROLADA
OVERALL MACHINE INFORMATION
2. DETAILED DESCRIPTIONS
2.1 OVERALL MACHINE INFORMATION
2.1.1 MECHANICAL COMPONENT LAYOUT
1
3
2
1. Tray
2. Overflow sensor feeler
3. Exit roller
4. Transport roller
4
G554V101.WMF
2.1.2 DRIVE LAYOUT
1
2
4
1. Shift motor
2. Main motor
3. Main motor timing belt
3
4. Timing belt
G554V103.WMF
G056/G058
11-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
10 October, 2000
OVERALL MACHINE INFORMATION
2.1.3 ELECTRICAL COMPONENT LAYOUT
1
5
6
2
7
3
8
10
G554V104.WMF
SM
1. Shift motor
6. Right shift sensor
2. Shift tray board
7. Cover sensor
3. Main motor
8. Paper overflow sensor
4. Junction gate solenoid
9. Shift timing sensor
5. Left shift sensor
10. Tray paper sensor
11-5
CÓPIA NÃO CONTROLADA
G056/G058
One-Bin Shift
Tray G554
9
4
CÓPIA NÃO CONTROLADA
DETAILED SECTION DESCRIPTIONS
2.2
DETAILED SECTION DESCRIPTIONS
2.2.1 BASIC OPERATION
[B]
[A]
[C]
G554V102.WMF
G554D101.WMF
[G]
[F]
[E]
[D]
G554D102.WMF
• The solenoid [A] opens the junction gates [B] to direct the paper to the tray.
2.2.2 SORT MODE OPERATION
• When the trailing edge of each page passes the shift timing sensor [D], the shift
motor [E] shifts the exit rollers [F] across. When the left or right shift sensor [G]
detects the rollers, the motor stops, then returns the rollers to the center.
• Each page of the first set is shifted to one side, then each page of the next set is
shifted to the other side. The rollers move back to the central position after
shifting each page.
G056/G058
11-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SwapBox
 and SwapFTL

Installation Manual
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
INTRODUCTION
1 INTRODUCTION
1.1 PRECAUTIONS
1.1.1 SWAPBOX AND SOFTWARE
If you purchase SwapBox from an authorized SCM Microsystems dealer, do not
use the software enclosed with the SwapBox. You need to purchase the required
software and license additionally from Ricoh.
The software part number is: A2309353
1.1.2 SOFTWARE LICENSE AGREEMENT
1.2
SYSTEM REQUIREMENTS
•
•
•
•
An IBM PC-AT compatible computer with ISA Plug & Play BIOS
One empty ISA bus slot (SBI-C2P and SBI-D2P)
One empty 3.5” drive bay (SBI-D2P)
Microsoft  Windows  95 operating system 4.00.950a or later version
installed (Refer to section 1.4 for more details.)
• At least 2MB of free disk space on the system partition (the partition where
Windows 95 is installed) for SwapFTL software installation
1.3
ITEMS TO PREPARE BEFORE INSTALLATION
• Computer hardware user’s manual
• Windows 95 installation disks or CD-ROM
• Windows 95 service pack (Refer to section 1.4 for more details.)
• SCM SwapBox SBI-C2P or SBI-D2P
SCM/RCH SwapFTL + SwapUTI (rev. 2.01 or later) software diskette, and a
software license
SM
12-1
CÓPIA NÃO CONTROLADA
G056/G058
SwapBox

And
SwapFTL

Before you use the software, you must agree to the SCM software license
agreement that is enclosed in either the SwapBox or the software.
Users must be responsible for the agreement with SCM Microsystems Inc. Ricoh
Co., Ltd. is not responsible for any legal problems caused by user’s actions
contrary to the agreement.
INTRODUCTION
1.4
CÓPIA NÃO CONTROLADA
WINDOWS 95 VERSION CONFIRMATION
Windows 95 has several different versions as shown in the following table.
Version
4.00.950
Description
First version
4.00.950a
First version (4.00.950) plus
service pack 1
4.00.950B
So called “OSR2 (OEM
Service Release 2)”
So called “OSR2.5 (OEM
Service Release 2.5)”
4.00.950C
Remarks
Not suitable for SwapBox and SwapFTL
installation.
Install service pack 1 (SP1) into Windows 95
version 4.00.950. SP1 is available from
Microsoft’s web site.
Only computers with Windows 95 preinstalled have had this version since 1997.
Only computers with Windows 95 preinstalled have had this version since 1998.
Check the Windows 95 version first, just by clicking the “System” icon in the
Windows Control Panel. If you see 4.00.950 in the box shown below, though the
example version is 4.00.950a, install “Service Pack 1” into the current Windows
operating system. Refer to the next page for how to get “Service Pack 1”.
4.00.950a
If the version is 4.00.950B or 4.00.950C, install SwapBox and SwapFTL without
updating Windows.
SM
12-2
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
INTRODUCTION
“Service Pack 1” is available from the Microsoft web site.
For the detailed information, refer to the following Internet address.
http://www.microsoft.com/windows95/info/service-packs.htm
Language
US English
Chinese (Simplified)
Chinese (Traditional)
Czech
Danish
Dutch
Finnish
German
Greek
Hungarian
Italian
Japanese (PCAT)
Korean
Norwegian
Pan-European
Polish
Portuguese
(Brazilian)
Portuguese (Iberian)
Russian
Slovenian
Spanish
Swedish
Thai
Turkish
SM
Internet Location
http://www.microsoft.com/windows95/info/service-packs.htm
Not available.
http://www.microsoft.com/windows/software/localize/tw-eu.htm
http://www.microsoft.com/windows/software/localize/cz-eu.htm
http://www.microsoft.com/windows/software/localize/dan-eu.htm
http://www.microsoft.com/windows/software/localize/dut-eu.htm
http://www.microsoft.com/windows/software/localize/fin-eu.htm
http://www.microsoft.com/windows/software/localize/frn-eu.htm
http://www.microsoft.com/windows/software/localize/ger-eu.htm
http://www.microsoft.com/windows/software/localize/grk-eu.htm
http://www.microsoft.com/windows/software/localize/itn-eu.htm
http://www.microsoft.com/windows/software/localize/jpcat-eu.htm
http://www.microsoft.com/windows/software/localize/kr-eu.htm
http://www.microsoft.com/windows/software/localize/nor-eu.htm
http://www.microsoft.com/windows/software/localize/pan-eu.htm
http://www.microsoft.com/windows/software/localize/pl-eu.htm
http://www.microsoft.com/windows/software/localize/brz-eu.htm
http://www.microsoft.com/windows/software/localize/pt-eu.htm
http://www.microsoft.com/windows/software/localize/ru-eu.htm
http://www.microsoft.com/windows/software/localize/slv-eu.htm
http://www.microsoft.com/windows/software/localize/spa-eu.htm
http://www.microsoft.com/windows/software/localize/swe-eu.htm
http://www.microsoft.com/windows/software/localize/thai2.htm
http://www.microsoft.com/windows/software/localize/trk-eu.htm
12-3
CÓPIA NÃO CONTROLADA
G056/G058
SwapBox

And
SwapFTL

The service pack file can be downloaded from the following Internet location.
Choose the one that is suitable for your Windows version.
SWAPBOX INSTALLATION
CÓPIA NÃO CONTROLADA
2 SWAPBOX INSTALLATION
2.1
HARDWARE INSTALLATION
CAUTION: 1) Before installing the SwapBox in a computer, turn off the computer
and disconnect the power cable.
2) This manual does not explain how to install an ISA board in your
computer. Refer to your computer’s users manual for how to do it.
Install the SwapBox as explained in Chapter 1 to 3 of the SwapBox Manual that is
enclosed in the SwapBox package.
Then go on to the next section below for the driver installation.
2.2
DRIVER INSTALLATION
CAUTION: 1) Do not use the software disks that are enclosed with the SwapBox.
2) Ensure that you have Windows 95 - 4.00.950a or a later version
installed in your computer. (Refer to section 1.4 for more details.)
1. Turn on the computer. “SCM SwapBox” may appear during boot-up.
2. When Windows 95 starts, it finds the SwapBox automatically and installs the
necessary driver files from the Windows installation diskette(s) or CD-ROM.
3. After Windows starts, choose “PCCard” from the Control Panel.
• If PCCard Properties is displayed, driver installation has finished.
You can go on to the next section.
• If PCCard Wizard is displayed, go on to the next step.
4. In the PCCard Wizard, choose all the default settings to finish the wizard, then
reboot the computer.
5. After Windows 95 has restarted, choose “System” from the Control Panel.
6. Choose “Device Manager” and confirm that “SCM SwapBox Family Plug and
Play PCMCIA Controller” is listed in the PCMCIA socket category.
7. Double-click “SCM SwapBox Family Plug and Play PCMCIA Controller” and
confirm that the SwapBox is working properly.
SM
12-4
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
SWAPBOX INSTALLATION
3 SOFTWARE (SWAPFTL) INSTALLATION
CAUTION: 1) If you purchased SwapBox from an authorized SCM dealer, do not
use the software diskettes that are enclosed in the SwapBox
package.
2) Use the software diskette which is labeled “SwapBox Software/ RCH
SwapFTL + SwapUTI”.
3) A software license is required to install a software package on a
computer.
4) The SwapFTL software may not work with some PC Card
(PCMCIA), CardBus, or ZV port controllers installed in notebook
computers.
3.1
SWAPFTL SOFTWARE INSTALLATION
1. Ensure that the SwapBox has been installed and configured under the
Windows 95 environment.
SwapBox

And
SwapFTL

2. Insert the software diskette in the floppy disk drive.
3. Choose “Run” from the Start menu.
4. Type “A:\setup” and click OK.
5. Follow the instructions on the display.
6. Reboot the computer after installation has finished.
3.2
VERIFICATION
3.2.1 SOFTWARE VERSION
1. Choose “SwapFTL Binary Utility” from the “SCMSwapFTL” program group.
2. After the utility starts, choose [Help] – [About SwapUti..].
3. Confirm that the version information is as follows:
SM
12-5
CÓPIA NÃO CONTROLADA
G056/G058
SWAPBOX INSTALLATION
CÓPIA NÃO CONTROLADA
3.2.2 FLASH MEMORY CARD AUTOMATIC DETECTION
1. Insert the 4MB flash memory card supplied from Ricoh into a card slot.
2. Windows 95 automatically detects the card, if this is the first time a flash card
has been used, Windows 95 installs the necessary drivers, and the “Found new
hardware” dialog box should appear automatically.
3. Wait about 30 s, then choose “SwapFTL Binary Utility” from the
“SCMSwapFTL” program group.
4. After the utility software starts, choose [Image] – [Read].
If “Failed to open PCCard” appears, see Troubleshooting.
5. Click OK to read the card.
If this works successfully, a new file is created as a temporary file, and this can
be stored on the computer.
SM
12-6
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
TROUBLESHOOTING
4 TROUBLESHOOTING
4.1
SWAPBOX RESOURCE CONFLICT
An ISA device must not share resources (IRQ, I/O address, and memory address)
with another device.
ISA plug and play BIOS automatically assigns necessary resources to ISA boards.
However, this could cause a problem if an ISA board requires specific resources.
The SwapBox requires a specific memory address range to activate card services.
So, if another ISA device or PCI device occupies this memory address range, the
SwapBox and SwapFTL will not work.
4.1.1 IRQ AND I/O ADDRESS
To identify whether an IRQ or I/O address has a conflict with another device, check
the SwapBox properties in the Windows device manager. If you find a conflict,
follow the instructions given by Windows Help.
The SwapBox and card services require a memory Window between 0xC8000 to
0xD3FFF.
The SwapBox properties do not tell you if the memory address is in conflict with
others. To identify whether the memory address is in conflict with another device,
do the following:
1. Choose “Computer” in the Windows device manager, and click “Properties”.
2. Choose “Memory” in the “View resources” tab.
3. Check if any other device is using the address range from 0xC8000 to
0xD3FFF. If it is a PCI device, you need to adjust the plug and play BIOS
settings. If it is an ISA device, you need to remove the device from the system.
Conflict with a PCI device
1. Shut down Windows and reboot the computer.
2. Enter BIOS setup during system boot-up.
NOTE: How to enter BIOS setup and BIOS setup options depends on your
system.
3. Find the ISA plug and play settings in the BIOS setup.
4. Adjust the settings so that the BIOS does not allocate the SwapBox memory
range to PCI devices.
Example: Award BIOS
1. Press the “DEL” key during boot-up to gain access to BIOS setup.
2. Choose “PNP AND PCI SETUP” from the main menu.
SM
12-7
CÓPIA NÃO CONTROLADA
G056/G058
SwapBox

And
SwapFTL

4.1.2 MEMORY ADDRESS
CÓPIA NÃO CONTROLADA
TROUBLESHOOTING
3 Change the “ISA MEM BLOCK BASE” setting as follows:
• ISA MEM BLOCK BASE: No/ICU → D000
• ISA MEM BLOCK SIZE: 8k
4 Press “Esc” to exit “PNP AND PCI SETUP”.
5 Choose “SAVE & EXIT SETUP”.
Conflict with a plug and play ISA device
1. Shut down the computer.
2. Remove the ISA device that is in conflict with the SwapBox.
3. Restart the computer and see if the SwapBox and the SwapFTL work under the
Windows environment.
Conflict with a legacy ISA device
Either remove the ISA device that is in conflict with the SwapBox to change its
jumper settings, or run the setup utility of the device to change the setting.
4.2 “FAILED TO OPEN PCCARD” ERRORS
4.2.1 TIMELAG TO LOADING DRIVER
Windows requires a certain time, which depends on system performance, to enable
card services for a flash memory card after inserting it in a PC card socket.
If you try to read, erase, or write to the card before the card service is ready, you
receive a “Failed to open PCCard” error.
Wait for about 30 s, then try again.
4.2.2 PCCARD NOT CONFIGURED
If the PCCard icon in the Windows Control Panel is not configured, you receive a
“Failed to open PCCard” error when you try to access the card.
Configure the PCCard icon using Control Panel as explained in the driver
installation procedure.
4.2.3 RESOURCE CONFLICT
If you receive a “Failed to open PCCard” error even if the SwapBox looks correctly
configured in the device manager, a memory address conflict is causing the error.
Refer to section 4.1.2 to solve the problem.
SM
12-8
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
TROUBLESHOOTING
4.3 ”INVALID DYNAMIC LINK CALL FROM
SWAPENUM…” ERROR
A blue screen error with a message “Invalid dynamic link call from SwapEnum to
device xxxx service x” may happen, if SwapFTL software was installed before
SwapBox had been activated.
Once this happens, follow the procedure below.
1. Uninstall SwapFTL (choose “SwapFTL Uninstall” from “SCM SwapFTL”
program menu).
2. Reboot the computer.
3. After Windows has restarted, double-click “System” icon in the Control Panel.
4. Choose “Device Manager” tab and double-click “SCM SwapBox” in the
“PCMCIA sockets” category.
5. If the device was not activated, activate it.
7. After Windows has restarted, re-install SwapFTL.
4.4 SWAPFTL PROBLEM WITH NOTEBOOK COMPUTERS
4.4.1 WINDOWS AND PC CARD DRIVER VERSION
Before installing the SwapFTL software into a notebook computer, ensure the
following.
• Windows 95 OSR2 is installed or Service Pack 1 is installed.
For how to identify the version of Windows 95, refer to section 1.4 for details.
• The latest PC Card driver is installed.
Contact your computer manufacturer or PC Card controller vender.
4.4.2 SYSTEM SUMMERY
If you still have problems after updating Windows and the drivers, send your
computer’s system summary to the support database.
To prepare the system summary as a PostScript file, do the following.
1. Install a PostScript printer (e.g., HP LaserJet 4 PS).
2. Double-click the “System” icon in the Control Panel.
3. Choose the “Device manager” tab, and select “Computer” in the device map.
4. Click the “Print” button.
5. Choose the PostScript printer using the “Setup” button, choose “All devices and
system summary” as the report type, and check the “Print to file” box.
6. Click OK to make a PostScript print file.
SM
12-9
CÓPIA NÃO CONTROLADA
G056/G058
SwapBox

And
SwapFTL

6. Reboot the computer.
TROUBLESHOOTING
4.5
CÓPIA NÃO CONTROLADA
COMPLETE UNINSTALL
If the SwapBox and the SwapFTL software do not work due to unsuccessful
configuration, the following process helps you to restart Windows plug and play
from the beginning.
This procedure uninstalls all the software and drivers that were installed for the
SwapBox, as well as deleting the Windows registry settings.
1. Uninstall the SCM SwapFTL programs.
Choose “SwapFTL uninstall” from the Start menu.
2. Delete the following files from the \Windows\System directory.
• SOCKETSV.VXD
• FLS2MTD.VXD
• FLS1MTD.VXD
• SRAMMTD.VXD
• CARDDRV.EXE
• CSMAPPER.SYS
• PCCARD.VXD
3. Delete “SCM SwapBox Family Plug and Play PCMCIA Controller” from the
Windows device manager.
(Choose ‘System” from the Control panel to access the device manager.)
4. Shutdown and restart Windows.
Windows starts the plug & play process again to install the SwapBox.
SM
12-10
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
SwapFTL
 Binary Utility
Operation Manual
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
OVERVIEW
Microsoft and Windows are registered trademarks of Microsoft Corp.
SwapBox and SwapFTL are trademarks of SCM Microsystems Inc.
1. OVERVIEW
This software allows a flash memory card to be used as an intermediate medium
between a flash ROM (or RAM) on the machine and a Windows 95 based
computer.
The basic procedure is as follows:
ROM File
Database
Communication
Link
1. You receive ROM files from a database either via
network or via physical medium, and save them
onto your computer’s local hard disk.
NOTE: Your computer works as a flash memory
card programmer after you install
SwapBox and SwapFTL software (this
software).
Windows 95 Computer
3. You carry the programmed card to a machine site
and download the ROM data from the card to the
machine’s internal flash ROM.
4MB
!
MEMO
NOTE: The 4MB flash memory card that is
customized for this application is
available from SPC.
You cannot use other types of flash
memory card.
4MB Flash Memory Card
A
4. After downloading ROM data to one machine,
you can use the same card with another machine
of the same type.
Machine
(e.g., NAD Copier)
SM
13-1
CÓPIA NÃO CONTROLADA
G056/G058
SwapBox

And
SwapFTL

2. You program the ROM file to a flash memory
card using this software.
CÓPIA NÃO CONTROLADA
OPERATION
2. OPERATION
2.1. PROGRAMMING A FLASH MEMORY CARD
2.1.1 GETTING A SOURCE FILE
You can (or will be able to) obtain the source firmware file(s) in one of the following
ways.
• Notes mail or through a Notes database
• Internet-mail
• BBS
• Floppy disk
• Flash memory card (you need to save the data on the card as a file on a PC
before using the data.)
• Others (as yet unspecified)
2.1.2 PROGRAMMING A CARD WITH THE SOURCE
A230/A231/A232 Copy and Fax Main Firmware
You can program copy and fax firmware together onto one 4MB flash memory
card, as shown below.
4MB
2MB
[Hex]
3FFFFF
Copy only
Fax only
Copy/Fax
combined
Fax
(FCU)
Fax
(FCU)
200000
1FFFFF
200000
1FFFFF
Copy
(BICU)
Copy
(BICU)
000000
SM
[Hex]
3FFFFF
000000
Start Address (Hex)
Length (Hex)
0
200000
200000
200000
Size (kB)
2,000 (2MB)
2,000 (2MB)
13-2
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
OPERATION
A230/A231/A232 Fax Modem Firmware and Fax SRAM Backup
Modem
Program modem firmware using the address and length settings as shown below.
You cannot program other data on the card once the modem firmware has been
programmed.
SRAM
Using Fax SP mode, you can make a backup of SRAM data onto the 4MB flash
memory card. This will help you set up multiple machines with fax options with the
same settings, or will help you restore user data if the SRAM data has been erased
accidentally.
To save the SRAM backup data from a fax unit on a 4MB flash memory card as a
file, or to program a backup file from a PC onto a 4MB flash memory card, use the
address and length settings as shown below.
4MB
[Hex]
3FFFFF
SRAM
(FCU)
Modem
SRAM
[Hex]
(FCU+EXSAF)
3FFFFF
2MB
200000
1FFFFF
220000 h
Modem
SRAM
(FCU+EXSAF)
SRAM (FCU)
000000
Start Address (Hex)
Length (Hex)
Size (kB)
SM
200000
1FFFFF
000000
200000
40000
256
200000
20000
128
13-3
CÓPIA NÃO CONTROLADA
200000
A0000
128 + 512
G056/G058
SwapBox

And
SwapFTL

2A0000 h
240000 h
CÓPIA NÃO CONTROLADA
OPERATION
2.2
DOWNLOADING TO A MACHINE
Refer to the machine’s service manual for how to download its firmware to the flash
ROM inside it.
2.3
SAVING DATA TO A FILE
Some machines can upload an internal flash ROM image to a flash memory card.
To save the image on the flash memory card as a computer file, read the card with
a specific address range setting that was mentioned in section 2.1.2, and save the
read data as a file.
SM
13-4
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
FUNCTIONS
3. FUNCTIONS
3.1
FILE MENU
3.1.1 [FILE] – [OPEN]
SwapBox

And
SwapFTL

This opens a binary file.
Use “Binary Files (*.bin)” or “SwapUti Files (*.dmp). Do not use the others.
The default setting is “Binary Files (*.bin).
An 8-bit checksum is displayed at the lower left corner of the opened file.
3.1.2 [FILE] – [CLOSE]
This closes an active file that has been opened.
3.1.3 [FILE] – [SAVE]
This saves an active file with the same name.
SM
13-5
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
FUNCTIONS
3.1.4 [FILE] – [SAVE AS]
This saves an active file with a different name from the original.
3.2
VIEW MENU
3.2.1 [VIEW] – [TOOLBAR]
This switches on the toolbar display.
3.2.2 [VIEW] – [STATUS BAR]
This switches on the status bar display.
SM
13-6
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
FUNCTIONS
3.3 IMAGE MENU
3.3.1 [Image] – [Erase]
Length
Base of Address/
Length
Description
Card slot number that has a flash memory card currently installed.
A “0 (zero)” appears at default.
To erase the whole card, do not change the setting
Hexadecimal length of the card appears at default.
To erase the whole card, do not change the setting
Do not change the settings.
The default setting is “Hex”.
NOTE: If the specified start address and length do not coincide with block
boundaries on the flash memory card, the message below appears.
SM
13-7
CÓPIA NÃO CONTROLADA
G056/G058
SwapBox

And
SwapFTL

Field
Source
Start Address
CÓPIA NÃO CONTROLADA
FUNCTIONS
3.3.2 [IMAGE] – [READ]
Field
Source
Start Address
Length
Base of Address/
Length
SM
Description
Card slot number that has a flash memory card currently installed.
A “0 (zero)” appears at default.
Change this setting if necessary.
Hexadecimal length of the card appears at default.
Change this setting if necessary.
Do not change the settings.
The default setting is “Hex”.
13-8
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
FUNCTIONS
Field
Source
Target
Card erase
before write
Start Address
Length
Base of Address/
Length
Description
Source file name that is currently active in the application.
Card slot number that has a flash memory card currently installed.
If this is checked, the application erases the whole card before writing
data from the source file.
The default setting is checked (= erase).
A “0 (zero)” appears at default.
Change this setting if necessary.
Hexadecimal length of the source file appears at default.
Do not change the setting.
Do not change the settings.
The default setting is “Hex”.
After writing the data to a flash memory card, an 8-bit checksum ① pops up, so that
you can compare it with the checksum ② of the source file.
SM
13-9
CÓPIA NÃO CONTROLADA
G056/G058
SwapBox

And
SwapFTL

3.3.3 [IMAGE] – [WRITE]
CÓPIA NÃO CONTROLADA
FUNCTIONS
3.3.4 [Image] – [Verification]
Field
Source
Target
Start Address
Length
Base of Address/
Length
Description
Source file name that is currently active in the application.
Card slot number that has a flash memory card currently installed.
A “0 (zero)” appears at default.
Change this setting if necessary.
Hexadecimal length of the source file appears at default.
Do not change the setting.
Do not change the settings.
The default setting is “Hex”.
If verification was successful, a ‘Verification OK!” message pops up.
If verification was not successful, a “Compare error !” message pops up with the
source and target addresses.
SM
13-10
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
FUNCTIONS
3.4 HELP MENU
SwapBox

And
SwapFTL

3.4.1 [HELP] – [ABOUT SWAPUTI…]
SM
13-11
CÓPIA NÃO CONTROLADA
G056/G058
CÓPIA NÃO CONTROLADA
G073/G074
SERVICE MANUAL
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
!IMPORTANT SAFETY NOTICES
PREVENTION OF PHYSICAL INJURY
1. Before disassembling or assembling parts of the copier and peripherals,
make sure that the printer power cord is unplugged.
2. The wall outlet should be near the printer and easily accessible.
3. Note that some components of the printer and the paper tray unit are
supplied with electrical voltage even if the main power switch is turned off.
4. If any adjustment or operation check has to be made with exterior covers off
or open while the main switch is turned on, keep hands away from electrified
or mechanically driven components.
5. The inside and the metal parts of the fusing unit become extremely hot while
the printer is operating. Be careful to avoid touching those components with
your bare hands.
HEALTH SAFETY CONDITIONS
Toner and developer are non-toxic, but if you get either of them in your eyes by
accident, it may cause temporary eye discomfort. Try to remove with eye drops
or flush with water as first aid. If unsuccessful, get medical attention.
OBSERVANCE OF ELECTRICAL SAFETY STANDARDS
The printer and its peripherals must be installed and maintained by a customer
service representative who has completed the training course on those models.
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL
1. Do not incinerate toner bottles or used toner. Toner dust may ignite
suddenly when exposed to an open flame.
2. Dispose of used toner, developer, and organic photoconductors in
accordance with local regulations. (These are non-toxic supplies.)
3. Dispose of replaced parts in accordance with local regulations.
LASER SAFETY
The Center for Devices and Radiological Health (CDRH) prohibits the repair of
laser-based optical units in the field. The optical housing unit can only be repaired
in a factory or at a location with the requisite equipment. The laser subsystem is
replaceable in the field by a qualified Customer Engineer. The laser chassis is not
repairable in the field. Customer engineers are therefore directed to return all
chassis and laser subsystems to the factory or service depot when replacement of
the optical subsystem is required.
!WARNING
Use of controls, or adjustment, or performance of procedures other than
those specified in this manual may result in hazardous radiation exposure.
!WARNING
WARNING: Turn off the main switch before attempting any of the
procedures in the Laser Unit section. Laser beams can seriously damage
your eyes.
CAUTION MARKING:
G058R500.WMF
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
INSTALLATION
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
1. INSTALLATION
Please refer to the base model (G056/G058) service manual for information on
installation requirements.
Please refer to the Setup Guide for machine installation procedures.
1.1 OPTIONAL UNIT INSTALLATION
The following options are available for this machine. Refer to the Setup Guide for
how to install these options.
• Paper Tray Unit
• 4-bin Mailbox
• 1-bin Shift Tray
• Duplex Unit
• Envelope Feeder
• NIB (G074 only) - the NIB is a standard component for the G073
• Hard disk
• IEEE1394
• 64-MB DIMM
• Wireless LAN (New option for this model)
SM
1-1
CÓPIA NÃO CONTROLADA
G073/G074
Installation
OPTIONAL UNIT INSTALLATION
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
PREVENTIVE MAINTENANCE
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
USER/SERVICE MAINTENANCE
2. PREVENTIVE MAINTENANCE
2.1 USER/SERVICE MAINTENANCE
Preventive
Maintenance
All PM items are the same as the base model (G056/G058). Please refer to the
base model (G056/G058) service manual for user/service maintenance.
SM
2-1
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
REPLACEMENT AND ADJUSTMENT
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
DIFFERENCES FROM THE MODEL G056/G058
3. REPLACEMENT AND ADJUSTMENT
All replacement and adjustment items are the same as the base model
(G056/G058), except for the item explained below. Please refer to the base model
(G056/G058) service manual for details about replacement and adjustment.
3.1 DIFFERENCES FROM THE MODEL G056/G058
Please note that the position of the thermistor attached to the laser unit has been
changed.
NOTE: The thermistor is included in the laser unit.
Removing the Laser Unit
Refer to the model G056/G058 manual for
removal steps for the following items.
Replacement
and
Adjustment
The following item has been changed from the model G056/G058.
[A]
Operation panel (☛ 3.2 Exterior Covers)
Upper cover (☛ 3.2 Exterior Covers)
Left cover (☛ 3.2 Exterior Covers)
[A]:
[B]:
[C]:
[D]:
230V machine only: Sheet (! x1)
Thermistor ( " x1)
Clip
Laser unit (! x4, 1 flat cable, " x2)
G073R730.WMF
[C]
[B]
[D]
G073R203.WMF
SM
3-1
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
TROUBLESHOOTING
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
4. TROUBLESHOOTING
4.1 SERVICE CALL CONDITIONS
4.1.1 SUMMARY
There are two levels of service call conditions.
Level
A
B
Definition
To prevent the machine from being damaged,
the SC can only be reset by a service
representative. The copier cannot be operated
at all.
The SC can be reset by turning the main
power switch off and on.
Reset Procedure
Enter engine service mode
(Fusing Error Clear) and press
“Enter.”
Turn the main power switch off
and on.
Troubleshooting
The new SC codes are shaded.
SM
4-1
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
Rev. 01/2003
4.1.2 CONTROLLER SC CODE DESCRIPTIONS
The following table describes the controller error codes. These codes are displayed
at power-on, or after the power-on self diagnostic test, if an error occurs.
Important: Always try turning the main switch off and on and check if the problem
persists.
⇒
SC
640
Level
B
641
B
670
B
671
B
800
B
818
B
819
B
G073/G074
Symptom
Possible Cause/Required Action
Controller to engine communication error.
Checksum error detected
• Defective controller
between the controller and
• Defective engine board
the engine board.
1. Check the connection between the
controller and the engine board.
2. Replace the engine board if the error is
frequent.
3. Replace the controller board if the error is
frequent.
Controller to engine communication error.
The controller receives no
• Defective controller
response from the engine
• Defective engine board
board.
1. Check the connection between the
controller and the engine board.
2. Replace the engine board if the error is
frequent.
3. Replace the controller board if the error is
frequent.
Engine start-up error
The ready signal from the
• Defective engine board.
engine board is not detected. Replace the engine board.
Engine board mismatch error
Engine board and controller
• Wrong engine board installed.
mismatch detected.
• Wrong controller board installed.
Check the type of engine board and controller
board.
Video data error
• Defective controller
• Defective engine board
1. Check the connection between the
controller and the engine board.
2. Replace the engine board if the error is
frequent.
System timeout error
System program timeout
• Defective controller
error detected.
Replace the controller if it occurs frequently.
Kernel abnormal end error
A HDD error or a software
• HDD Error
error has occurred, terminating Software application error RAM shortage.
the SCS process, gwinit
process, and finally the kernel
program. A system process
has exhausted the RAM.
4-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
Level
820
B
821
B
822
B
823
B
824
B
827
B
828
B
829
B
835
B
836
B
837
B
SM
Symptom
Possible Cause/Required Action
Self-diagnostic error - CPU
CPU error detected during
• Defective controller
self-diagnostic.
Replace the controller if the error is frequent.
Self-diagnostic error - ASIC/CPU
ASIC and CPU timer error
• Defective controller
detected during self1. Replace the controller if the error is
diagnostic.
frequent.
Self-diagnostic error - HDD
HDD timeout error detected • Poor HDD connection
during self-diagnostic.
• Defective HDD
1. Check the HDD connection.
2. Replace the HDD.
Self-diagnostic error - NIB
NIB error detected during
G073 model: Defective controller
self-diagnostic.
Replace the controller.
G074 model:
• Poor NIB connection
• Defective NIB or controller
1. Check the connection between the NIB
and the controller.
2. Replace the NIB.
Self-diagnostic error - NVRAM
NVRAM error detected
• Poor NVRAM connection
during self-diagnostic.
1. Check if the NVRAM is properly installed.
2. Replace the NVRAM
Self-diagnostic error - standard SDRAM
Standard SDRAM
• Defective controller
(memory) error detected
Replace the controller if the error is frequent.
during self-diagnostic.
Self-diagnostic error - Flash ROM
Flash ROM error detected
• Defective controller
during self-diagnostic.
Replace the controller if the error is frequent.
Self-diagnostic error - Optional RAM
Memory RAM error
• Poor connection of the optional memory
detected during self• Defective memory RAM
diagnostic.
1. Check the connection of the optional
memory.
2. Replace the memory DIMM.
Self-diagnostic error - Parallel interface
Parallel interface error
• Defective controller
detected during selfReplace the controller.
diagnostic.
Self-diagnostic error - Font ROM
Not used for this model.
Self-diagnostic error - Optional font ROM
Not used for this model.
4-3
CÓPIA NÃO CONTROLADA
G073/G074
Troubleshooting
SC
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
SC
Level
838
B
850
B
851
B
853
B
854
B
855
B
856
B
857
B
860
B
G073/G074
Symptom
Possible Cause/Required Action
Self-diagnostic error - Clock generator
Controller clock generator
• Defective controller
error detected during selfReplace the controller.
diagnostic.
NIB interface error
NIB interface error
• Defective controller
detected.
Replace the controller.
IEEE1394 interface error
IEEE1394 interface error
• Defective controller
detected.
Replace the controller.
IEEE802.11b error - card not detected (power-on)
Wireless LAN card not
• Poor connection
detected at power-on.
• Defective wireless LAN card
• Defective controller
1. Check the wireless LAN card connection.
2. Replace the wireless LAN card.
IEEE802.11b error - card not detected (during operation)
Wireless LAN card not
• Poor connection
detected during operation.
• Defective wireless LAN card
• Defective controller
1. Check the wireless LAN card connection.
2. Replace the wireless LAN card.
IEEE802.11b error
Wireless LAN card error
• Poor connection
detected.
• Defective wireless LAN card
• Defective controller
1. Check the wireless LAN card connection.
2. Replace the wireless LAN card.
IEEE802.11b interface board error
Wireless LAN interface
• Poor connection
board error detected.
• Defective wireless LAN interface board
1. Check the wireless LAN interface board
connection.
2. Replace the interface board.
USB I/F Error
USB interface error
• Defective controller
detected.
1. Check the USB connections, make sure
that they are securely connected.
2. Replace the controller board.
HDD start-up error
HDD initialization error
• Defective HDD
detected.
1. Check the HDD connection.
2. Reformat the HDD.
3. Replace the HDD.
4-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SERVICE CALL CONDITIONS
Rev. 01/2003
864
865
990
991
⇒
998
999
SM
Level
B
B
B
B
B
B
B
Symptom
HDD data unable to read
Data stored in the HDD
cannot be properly read.
HDD data access error
HDD access error detected.
HDD access error
An error detected during
HDD operation.
Unexpected software error
Unexpected software error
detected.
Unexpected software error
Unexpected software error
detected, which does not
affect operation of the
machine.
Application Start Error
After power on, the
application does not start
within 60s. (All applications
neither start nor end
normally.)
Software update error
Software updating failed.
Possible Cause/Required Action
•
1.
2.
3.
Defective HDD
Check the HDD connection.
Reformat the HDD.
Replace the HDD.
• Defective HDD
Replace the HDD.
• Defective HDD
Replace the HDD.
• Defective controller
Replace the controller if the error is frequent.
The machine does not stop and the SC code
is not displayed. The machine automatically
recovers.
However, the SC code is logged in the
engine summary sheet (SMC).
Software defective.
An option required by the application (RAM,
DIMM, board) is not installed
Try downloading the controller firmware
again.
4-5
CÓPIA NÃO CONTROLADA
G073/G074
Troubleshooting
SC
863
CÓPIA NÃO CONTROLADA
JAM LOCATIONS
4.2 JAM LOCATIONS
The following codes are displayed on the SMC report to locate where the jam
occurred in the machine.
For example, if the following is printed on the SMC report:
020
0003260
This means that the jam occurred during registration (paper did not reach the
registration sensor) when the print counter was 3260.
Jam Code
017
018
019
020
021
022
023
024
025
033
034
035
036
049
050
051
052
053
054
G073/G074
Description
PFU (tray 2) paper feed sensor not turned on
PFU (tray 3) paper feed sensor not turned on
Registration sensor not turned on - bypass feed
Registration sensor not turned on - tray 1
Registration sensor not turned on – paper feed unit
Registration sensor not turned on - duplex
Registration sensor not turned off
Paper exit sensor not turned on
Paper exit sensor not turned off
Paper exit sensor not turned on - shift tray or mailbox
Paper exit sensor not turned off - shift tray or mailbox
Vertical transport sensor not turned on - mailbox
Vertical transport sensor not turned off - mailbox
Duplex entrance sensor not turned on
Duplex entrance sensor not turned off
Duplex inverter sensor not turned on
Duplex inverter sensor not turned off
Duplex exit sensor not turned on
Duplex exit sensor not turned off
4-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
FIRMWARE HISTORY
Rev. 12/2002
⇒4.3
FIRMWARE HISTORY
4.3.1 PRINTER ENGINE FIRMWARE MODIFICATION HISTORY
Please check the http://tsc.ricohcorp.com website for current firmware
downloads.
Accessory firmware modification history is provided in the appropriate
accessory section of the service manual.
G073/G074 PRINTER ENGINE FIRMWARE MODIFICATION HISTORY
FIRMWARE
LEVEL
G0765135D
DESCRIPTION OF MODIFICATION
First Mass Production
G0765135E
FIRMWARE
VERSION
1.05
1.06
Troubleshooting
Corrects the following:
The Main Scan Magnification Adjustment (SP
Mode) did not function properly with the
previous version.
SERIAL
NUMBER
First Mass
Production
July ’02
Production
SM
4-7
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
FIRMWARE HISTORY
Rev. 12/2002
4.3.2 PRINTER CONTROLLER FIRMWARE MODIFICATION
HISTORY
⇒
G073/G074 PRINTER CONTROLLER FIRMWARE MODIFICATION HISTORY
FIRMWARE
LEVEL
G0735900B
DESCRIPTION OF MODIFICATION
First Mass Production
Corrects the following:
While downloading PS fonts to a machine with
the HDD option installed, the correct PS serial
number cannot be output.
Corrects the following:
Program update error occurs when Verify
mode in the firmware updating procedure is
used.
PM counter count-up method for Meter-charge
mode is corrected.
Change in Specification:
Symbol sets PC-858, Latin 9 and Roman 9 have
been added for EURO currency symbol.
Corrects the following:
SNMP vulnerability
SNMP security vulnerabilities reported by
CERT on Feb.12, 2002 have been confirmed
and fixed through the PROTOS c06-snmpv1
test suite.
-CERT: http://www.cert.org/advisories/CA2002-03.html
-PROTOS c06-snmpv1 test Suite:
http://www.ee.oulu.fi/research/ouspg/protos/tes
ting/c06/snmpv1/
New features added to User Mode (see 4.3.3 User
Mode Tree):
1. Letterhead Mode
On: The machine feeds all pages through the
duplex unit so that the last page of an oddpaged job is printed onto the front side of the
paper.
2.
3.
4.
SERIAL
NUMBER
First Mass
Production
Feb. ’02
Production
FIRMWARE
VERSION
1.01
G0735900D
March ’02
Production
1.03
G0735900E
April ’02
Production
1.04
G0735900C
Off (default setting): The last sheet of an oddpaged job is not fed through the duplex unit,
therefore although the output time of this
sheet is slightly faster, the last page is printed
onto the rear side.
802.11 Ad hoc mode (one type of Ad hoc
mode used with wireless LAN) is supported
from this version.
SSID (used for infrastructure mode with
wireless LAN) can now also be programmed
from User Mode. Previously, this was only
possible using Web Status Monitor or telnet.
128-bit WEP key (a wireless LAN security
feature) is supported from this version.
Previous versions supported only 64-bit WEP.
G073/G074
4-8
CÓPIA NÃO CONTROLADA
1.02
…continued
SM
CÓPIA NÃO CONTROLADA
FIRMWARE HISTORY
Rev. 12/2002
G073/G074 PRINTER CONTROLLER FIRMWARE MODIFICATION HISTORY
DESCRIPTION OF MODIFICATION
Corrects the following:
PCL
• Certain characters do not print
• Modified so that some characters in symbol
sets MS Text and Windows Baltic (19L) will
appear exactly as they do with HP printers.
• Modified so that PCLXL unsupported symbol
(6M, 13J and 14J) sets will appear as "XL
ERROR".
Change in Specification:
• If the machine has no HDD option, the PCL
HDD Directory List ( and font source) will not
be printed on the PCL Configuration Page.
• Supports the Status Read back function of the
PCL5e.
• If SSID is not entered, the message "SSID not
entered" will display on the control panel for 3
seconds.
• Supports PCLXL Euro symbol sets (PC-858,
Latin 9, and Roman 9).
Corrects the following:
FIRMWARE
LEVEL
G0735900F
SERIAL
NUMBER
June ’02
Production
FIRMWARE
VERSION
1.05
G0735900G
Oct. ’02
Production
1.07
Polish wording error:
Incorrect:
Diskonaly
Correct:
Dostateczny
German wording error:
Incorrect:
WEP Einstelling
Correct:
WEP Einstellung
Changed the default setting of DHCP to ON.
NOTE: There is no change when updating the
firmware. This feature is for the factory default.
Support the new device type of wireless LAN
(IEEE802.11b)..
HTTP and telnet protocols can be
opened/closed using telnet.
NOTE: After making the setting to disable
HTTP, you cannot access the target device
through web browser.
If you want to change this settings, please use
telnet to open HTTP.
When telnet port is disabled, you have to clear
the network settings (Memory Clear for NCS)
to open the telnet port.
…continued
SM
4-9
CÓPIA NÃO CONTROLADA
G073/G074
Troubleshooting
⇒
CÓPIA NÃO CONTROLADA
FIRMWARE HISTORY
⇒
Rev. 12/2002
G073/G074 PRINTER CONTROLLER FIRMWARE MODIFICATION HISTORY
FIRMWARE
LEVEL
DESCRIPTION OF MODIFICATION
SERIAL
NUMBER
FIRMWARE
VERSION
The following has been corrected;
PCL
• Euro font does not print correctly.
• Line Spacing Command, "lochEsc&l#D"loch,
causes incorrect output
• Same line widths when BitSW #3-3 is ON in
CAD printing
• Some True Type font might not be bolded.
• Slow Printing from AutoCAD
• When using bold font, lines may be printed on
the blank of page.
PS3
• The printing speed of a PS job slows down
after a PS3 job is reset.
• PS print file is printed as text
• Lines may be printed on the blank of page.
• The printer controller locks-up when printing
from Unix Acrobat.
• Euro symbol is not printed when using PS
driver.
G073/G074
4-10
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SERVICE TABLES
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
PRINTER CONTROLLER SERVICE MODE
5. SP MODE TABLES
Refer to section 5.1.1 of the manual for the base model (G056/G058) for how to
enable and disable service program mode.
5.1 PRINTER CONTROLLER SERVICE MODE
Service Table Key
Notation
[range / default / step]
DFU
What it means
Example: [-8.0 to +8.0 / 0 mm / 2 mm/step] The setting can be
adjusted in the range ±8, reset to 0 after an NVRAM reset, and the
value can be changed in 2 mm steps.
Denotes “Design or Factory Use”. Do not change this value.
5.1.1 SERVICE MODE MENU (“1. SERVICE MENU”)
Clear Setting
Print Summary
Disp Version
SM
Description
Bit switch
settings
Initialize the
system settings
Controller
summary print
Display
controller
Function
Adjusts bit switch settings.
Initializes settings in the “System” menu of the user
mode.
Prints the service summary sheet (a summary of all the
controller settings).
Displays the version of the controller.
5-1
CÓPIA NÃO CONTROLADA
G073/G074
Service
Tables
Service Mode
Bit Switch
CÓPIA NÃO CONTROLADA
PRINTER CONTROLLER SERVICE MODE
Rev. 10/2003
5.1.2 BIT SWITCH PROGRAMMING
Refer to section 5.2.2 of the service manual for the base model (G056/G058) for
how to program bit switch settings.
Bit Switch 01 - Not used (do not change any of these settings)
⇒
⇒
Bit Switch 02
No
Description
0-2 Not used
3 PDL Sniffing
Treatment of the last page
when printing a job with an
odd number of pages using
the duplex unit
4 0: (default): Last page not
fed through the duplex unit
1: Last page fed through
the duplex unit
Function
Do not change the setting.
See PUB(C)-051 for details.
0: The last page is not fed through the duplex unit, so
the last page faces the opposite way from other pages
in the job.
1: The last page is fed through the duplex unit, so the
last page faces the same way as other pages of the
job.
Set this switch to “1” when the customer wishes the last
page to be facing the same way as the other pages.
5-7
Do not change the setting.
Not used
Bit Switch 03
No
Description
0 PS Fonts Download
1-2 Not used
CAD printing line widths
0: OFF (default):
1: ON - CAD Printing line
3
widths (255 pens)
4-7
Not used
Function
See PUB(C)-045 for details.
Do not change the setting.
0: CAD printing line widths is OFF.
1: CAD Printing line widths (255 pens)
Set this switch to “1” when the customer wishes to print
HP G/L2 files correctly. (Requires controller firmware
version 1.09 or newer.).
Do not change the setting.
Bit Switch 04 - Not used (do not change any of these settings)
G073/G074
5-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
5.2 PRINTER ENGINE SERVICE MODE
5.2.1 SERVICE MODE TABLE (“2. ENGINE MAINTE”)
The new SP modes added for this model are shaded.
Description
Paper feed
timing
Fusing
Control
Fusing power
control
Fusing Temp
Fusing
temperature
adjustment
Fusing
temperature
display
Bypass paper
feed roller
rotation for
transparencies
Initial fusing
setting
Fusing T Disp
OHP Clutch
Rt
Fusing Start
Charge Rol
Bias
Mainscan
mag
Subscan mag
Developer
Bias
Toner End
Count
SM
Charge roller
voltage
adjustment
Main scan
magnification
adjustment
Sub scan
magnification
adjustment
Development
Bias
Adjustment
Number of
prints after
toner near-end
is detected
Function /[Setting]
Adjusts the paper feed clutch timing at registration. The
paper feed clutch timing determines the amount of paper
buckle at registration. (A larger setting leads to more
buckling.)
[-8.0 to +8.0 / 0 mm / 2 mm/step]
Selects whether the fusing power control is on/off or
phase control.
Use “Phase” control if the room lights flicker when the
fusing lamp starts.
[Normal (USA), Phase (Europe/Asia)]
Adjusts the fusing temperature for printing.
[100 to 200 / 170°C / 10°C /step]
DFU
Displays the fusing temperature.
Selects the number of rotations for the bypass feed roller
when the paper type is set to “Transparencies.”
This is to avoid jams when transparencies are being
used.
Roller turn:
Warms up the fusing unit for 20 s at power on or when
the machine warms up from the energy saver mode.
Normal:
There is no 20 s warm-up period.
Normally do not change the setting.
Adjusts the charge roller voltage. DFU
[1000 to 2000 / 1700V / 10 V/step]
Adjusts the main scan magnification.
[-0.5 to +0.5 / 0 % / 0.1 %/step]
Adjusts the sub scan magnification.
[-0.5 to +0.5 / 0 % / 0.1 %/step]
Adjusts the development bias for printing. DFU
[-800 to –200 / -700V / 10 V/step]
Adjusts the number of prints the machine can print after
it detects toner near-end.
[50 to 200 / 200 sheets / 50 sheets/step]
5-3
CÓPIA NÃO CONTROLADA
G073/G074
Service
Tables
Mode Name
Regist sag
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Mode Name
Transfer Set
Description
Transfer
correction
current
Test Pattern
Test pattern
selection
Thermistor
adj
Thermistor
adjustment
Toner end
clear
Waste Toner
Count
Effective info
Toner end clear
(engine)
Waste toner
count display
Cartridge ID
chip features
that are used
Cartridge Lim
Number of
prints for a
single cartridge
Cartridge
Stop
Action when
toner end is
detected
Toner end
sensor
Cartridge info
Toner near-end
threshold
Toner cartridge
information
G073/G074
Function /[Setting]
Adjusts the correction current applied to the transfer
roller.
[0 - 2 / 0 / 1 step]
0: –2 µA
1: 0 µA
2: +2 µA
3: +4 µA
Use this to select and print a test pattern. This machine
has the following patterns.
No pattern
Checkered pattern
Cross stitch
2 dot argyle
1 dot argyle
2 dot trim
2 dot grid
1 dot grid
Reset this to 0 after printing the test pattern, or the
selected pattern will appear on every page printed by the
user.
Charge roller voltage and transfer current automatic
adjustment.
The machine automatically adjusts these parameters in
response to the temperature within the machine. DFU
[On, Off]
Clears the toner end counter in the engine board.
Note: This mode is not used in this machine.
Displays the waste toner counter in the engine board.
Selects which of the cartridge ID chip functions are
enabled.
Normal mode: Cartridge detection/Type ID/Version
Cartridge dtct: Cartridge detection only
Note used: All items ignored
All used: All items used
Adjusts the number of prints the machine can make after
a new cartridge is detected.
Do not use a higher value than 30 k.
15k prints
20k prints
25k prints
30k prints
35k prints
40k prints
Determines whether the machine stops printing after the
cartridge counter reaches the above limit.
[Stop printing / Do not stop]
Threshold adjustment for the toner end sensor. DFU
[200 to 1000 / 200 ms / 100 ms/step]
Displays toner cartridge information.
5-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
Mode Name
mm/inch
display
ROM Update
Disp
Description
mm/inch
display
selection
User mode
“ROM Update”
display
selection
A3/11x17
Count
A3/DLT double
count
Auto Off set
Energy saver
on/off
Ulimit Auto
Set
Memory clr
Automatically
add user code
in the Web
Status Monitor
Memory clear
Free run
Free run
Input check
Input check
mode
Output check
mode
Output check
Function /[Setting]
Display units (mm or inch) for custom paper sizes.
0: mm (Europe/Asia)
1: inch (USA)
Currently, user mode “ROM Update” is not used.
0: Display this user mode
1: Do not display this user mode
Note: Do not change the setting.
Specifies whether the counter is doubled for A3/11" x 17"
paper.
If “Yes” is selected, the total counter counts up twice
when A3/11" x 17" paper is used.
Switches the energy saver mode on/off.
0: Enable, 1: Disable
Note: This setting is the same as the user mode “Energy
Saver” in the System menu.
Determines whether the machine adds new user codes
in the User Management Tool in Smart Net Monitor.
0: Automatically added
1: Not added
Resets software counters and returns modes and
settings to their defaults.
Memory all clear: Clears all data
Eng: Clears the printer engine settings
SCS: Clears the systems settings
PRT: Clears user mode system settings
NCS: Clears the items listed in the “Host Interface”
section of the Configuration page.
The machine performs a free run.
Press [Enter] to start.
Press [Enter] to stop.
Please note that the machine will not stop immediately
after the [Enter] key is pressed.
Displays signals received from sensors and switches.
See the “Input Check” section for details.
Turns on electrical components individually for test
purposes.
See the “Output Check” section for details.
Resets a service call condition (for fusing unit errors).
Fusing err clr
SC code reset
Serial
number
Service TEL
Serial Number
Use to input the machine serial number.
Programming
(This is normally done at the factory.)
Service station
Program the service station number.
number
The number is printed on the meter-charge counter
programming
report when the meter-charge mode is turned on.
Job spool settings/ Interface selection for Ethernet and wireless LAN
HD Job Clear
Treatment of the job when a spooled job exists at power
on.
0: Data is cleared
1: Automatically printed
Set Network
SM
5-5
CÓPIA NÃO CONTROLADA
G073/G074
Service
Tables
PRINTER ENGINE SERVICE MODE
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Mode Name
Set Network
Description
Job spool
(LPR)
Job spool (IPP)
Primary I/F
Current I/F
HDD Init
Prog
Checksum
IEEE1394
IEEE802.11b
USB
Test Print
Plug/Play
G073/G074
Initializes the
HDD
--Wireless LAN
available
channel setting
USB settings
Transfer Rate
Vendor ID
Product ID
Dev. Release
Num
Engine test
pattern print
Plug & Play
name selection
Function /[Setting]
Job spool on/off (LPR).
0: Job spool off
1: Job spool on
Job spool on/off (IPP).
0: Job spool off
1: Job spool on
Interface selection for the Ethernet or wireless LAN when
both interfaces are available.
0: Ethernet
1: IEEE802.11b (wireless LAN)
Note: This setting is same as the user mode setting “LAN
Type” in the Network Setup of the Host Interface menu.
Displays the current interface setting (Ethernet or
wireless LAN).
Initializes the hard disk.
Use this only if there is a hard disk error.
DFU
DFU
Sets the maximum and minimum value for the wireless
LAN channel adjustment. DFU
[0 to 14]
Europe/Asia: 1 to 13
USA: 1 to 11
Note: Do not change the setting, or the machine may be
out of compliance with local regulations.
Adjusts the USB transfer rate.
HS/FS: High speed/Full speed auto adjust
(480Mbps/12Mbps)
FS Fixation: Full speed (12Mbps fixed)
Do not change the setting unless there is a data transfer
error using the USB high speed mode.
Displays the vendor ID. DFU
Displays the product ID. DFU
Displays the development release version number. DFU
Prints the test pattern that was selected in the “Test
Pattern” mode.
Select the plug & play name.
5-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Debug Serial
Service
Report
Operation
time
Total counter
Disp ROM
ver
PM Counter
PM Counter
reset
Diag result
Assert Info
SM
Description
Meter-charge
mode
Function /[Setting]
Enable or disable meter-charge mode.
Important: Turn the main switch off/on after changing
this setting.
Yes: Enabled
No: Disabled
Meter charge mode enabled:
• "Replace Maintenance Kit" is not displayed on the
operation panel when the PM counter runs out (the
technician replaces the maintenance kit items)
• The meter charge counter is shown immediately after
the Menu key is pressed.
• The technician must reset the PM counter after
replacing the fusing unit.
Meter charge mode disabled:
• "Replace Maintenance Kit" is displayed on the
operation panel when the PM counter runs out (the
user replaces the maintenance kit items)
• The meter charge counter is not shown when the
Menu key is pressed.
• The PM counter resets automatically after the user
replaces the fusing unit.
--DFU
Prints summary sheet.
SP Mode Print
Prints the engine summary sheet.
NIB Summary
Prints the NIB summary sheet.
Total engine
Displays the total number of engine rotation cycles made
rotation cycle
so far.
Note: One cycle is calculated as 3.7 s of drum rotation.
However, this counter also includes idle rotations.
This counter is not reset at PM.
Controller total
Displays the controller total counter. This counter is used
counter display for meter charge, and it appears when the user presses
the Menu key (if meter charge mode is enabled).
It does not count up when certain items, such as service
reports, are printed (see section 6.6.1. for a complete list
of conditions).
ROM version
Displays the firmware version (system, engine, and
display
duplex).
PM counter
Displays the PM counter. This is not a page counter. It
display
estimates the page count using the engine rotation cycle
count. It counts up one page when the engine has made
the average number of rotations that is required for one
page of a three-page job.
Resets the PM
Resets the PM counter.
Important: If a technician replaces the PM items, reset
counter
this counter after replacing these items.
Diagnostic
Displays the controller self-diagnostic result.
result display
--DFU
5-7
CÓPIA NÃO CONTROLADA
G073/G074
Service
Tables
Mode Name
Meter charge
CÓPIA NÃO CONTROLADA
PRINTER ENGINE SERVICE MODE
Mode Name
Usercode clr
Description
User code clear
Total counter
Engine total
counter display
Function /[Setting]
Clears the user code data from the controller board
memory.
Displays the engine total counter. It counts up for all
prints, including service reports.
5.2.2 INPUT / OUTPUT CHECK TABLE
The input and output check tables are the same as the base model G056/G058.
Refer to section 5.3.2 and 5.3.3 of the G056/G058 manual.
G073/G074
5-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
USER PROGRAM MODE
Rev. 12/2002
5.3 USER PROGRAM MODE
User Mode
Counter (Meter-charge mode must be switched on by the SP mode)
Sample Print (optional HDD required)
Locked Print (optional HDD required)
Paper Input
Bypass Size
Tray Paper
Paper Type
Tray Locking (all trays can be locked)
Tray Priority
List/Test Print
Maintenance
Image Density
Registration
Curl Prevention
ROM Update
HDD Format (optional HDD required)
WL. LAN Signal (Wireless LAN required)
WL. LAN Defaults (Wireless LAN required)
Key Repeat
System
Misfeed Recovery
Print Error Report
Auto Continue
Memory Overflow
Sub Paper Size
Page Size
Edge to Edge Print
Duplex (optional duplex unit required)
Output Tray (only installed trays are displayed)
Job Separation (1-bin shift tray required)
Energy Saver
Memory Usage
Unit of Measure
Edge Smoothing
Service
Tables
⇒
The user menu list can be printed using “Menu List” in the “List/Test Print” user
mode.
Resolution
Toner Saving
Spool Printing
Host Interface
Letterhead
Off
I/O Buffer
On
I/O Timeout
Network Setup (NIB required)
IEEE1394 Setup (IEEE1394 required)
IEEE802.11b Setup (Wireless LAN required)
Comm. Mode
PCL Menu
802.11 Ad hoc
Infrastructure
USB Setting
Ad hoc
Orientation
Form Lines
Channel
Font Source
Trans Speed
11 Mps
Font Number
5.5 Mps
Point Size
2 Mps
1 Mps
Font Pitch
Symbol Set
SSID
Ext. A4 Width
View
Enter ID
WEP Settings
Language
Active
Not Active
NOTE: 1) Note 1: “ROM Update” is currently not used.
2) Press “Enter”, “Escape”, then “Menu” key to display the underlined user
mode.
SM
5-9
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
DETAILED DESCRIPTIONS
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CONTROLLER BOARD
6. DETAILED SECTION DESCRIPTIONS
USB I/F
USB I/F
PCI
USB I/F
CPU
RM 5231A-250
PCI Option I/F
6.1 CONTROLLER BOARD
ASIC
S IM AC
IEEE 1284 I/F
O ption .2.13
S DRAM -DIM M
P CI
Engine I/F
HD D I/F
SD RAM
Data Bus
Control Signals
ROMDIMM
(Not
used)
Font ROM
NIB I/F
(standard for
G073 model)
FLASH
RO M
Detailed
Descriptions
NVRAM
IC CARD
I/F
C ontroller B oard
G073D909.WMF
SIMAC:
CPU:
SDRAM:
Flash ROM:
PCI Interface:
NIB Interface:
SM
The same type of the ASIC is used with the model G056/G058.
32-bit CPU (RM5231A-250)
32MB SDRAM
8MB Flash ROM
Options such as the wireless LAN and IEEE1394 are installed.
Standard interface for G073 model.
6-1
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
USB
6.2 USB
6.2.1 SPECIFICATIONS
This model is equipped with standard USB.
Interface: USB 1.1, USB 2.0
Data rates: 480 Mbps (high speed), 12 Mbps (full speed), 1.5 Mbps (low speed)
High speed mode is only supported by USB 2.0.
6.2.2 USB 1.1/2.0
USB (Universal Serial Bus) offers simple connectivity for computers, printers,
keyboards, and other peripherals. In a USB environment, terminators, device IDs
(like SCSI), and DIP switch settings are not necessary.
USB 1.1 contains the following features:
• Plug & Play
• Hot swapping (cables can be connected and disconnected while the
computer and other devices are switched on)
• No terminator or device ID required
• Data rates of 12 Mbps (full speed), and 1.5 Mbps (low speed)
• Common connectors for different devices
USB 2.0 is an evolution of the USB 1.1 specification. It uses the same cables,
connectors, and software interfaces so the user will see no change.
It provides an easy-to-use connection to a wide range of products with a maximum
data rate of 480 Mbps (high speed).
Up to 127 devices can be connected and 6 cascade connections are allowed.
Power is supplied from the computer and the maximum cable length is 5 m.
G073/G074
6-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
USB
6.2.3 USB CONNECTORS
USB is a serial protocol and a physical link, which transmits all data on a single pair
of wires. Another pair provides power to downstream peripherals.
The USB standard specifies two types of connectors, type “A” connectors for
upstream connection to the host system, and type “B” connectors for downstream
connection to the USB device.
G073D905.WMF
G073D904.WMF
Type “A” connector
Type “B” connector
6.2.4 PIN ASSIGNMENT
The controller has a type “B” receptacle (CN10).
CN1
CN5 (SLOT1)
CPU
SIMAC
Controller Board
Detailed
Descriptions
IC Card I/F
CN2
4
Ethernet I/F
(standard for G073 model)
CN4
3
USB I/F
NVRAM
1
Parallel I/F
2
G073D906.WMF
Pin No.
1
2
3
4
SM
Signal Description
Power
Data –
Data +
Power GND
Wiring Assignment
Red
White
Green
White
6-3
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
USB
6.2.5 REMARKS
• The machine does not print reports specifically for USB.
• Only one host computer is allowed for the USB connection.
• After starting a job using USB, do not switch the printer off until the job has been
completed.
When a user cancels a print job, if data transmitted to the printer has not been
printed at the time of cancellation, the job will continue to print up to the page
where the print job was cancelled
• When the controller board is replaced, the host computer will recognize the
machine as different device.
Related SP Mode
“USB Settings” in the printer engine service mode. Data rates can be adjusted to
full speed fixed (12 Mbps). This switch may be used for troubleshooting if there is a
data transfer error using the high speed mode (480 Mbps).
Data rates can also be adjusted using the UP mode “USB Setting” in the Host
Interface in the System menu.
This mode can be accessed only when the “Enter”, “Escape”, then “Menu” keys are
pressed to enter the UP mode.
G073/G074
6-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IEEE802.11B (WIRELESS LAN)
6.3 IEEE802.11B (WIRELESS LAN)
6.3.1 SPECIFICATIONS
A wireless LAN is a flexible data communication system used to extend or replace
a wired LAN. Wireless LAN employs radio frequency technology to transmit and
receive data over the air and minimize the need for wired connections.
• With wireless LANs, users can access information on a network without looking
for a place to plug into the network.
• Network managers can set up or expand networks without installing or moving
wires.
• Most wireless LANs can be integrated into existing wired networks. Once
installed, the network treats wireless nodes like any other physically wired
network component.
• Flexibility and mobility make wireless LANs both effective extensions of and
attractive alternatives to wired networks.
Standard applied:
IEEE802.11b
Data transfer rates:
11 Mbps/5.5 Mbps/2 Mbps/1 Mbps (auto sense)
Network protocols:
TCP/IP, Apple Talk, NetBEUI, IPX/SPX
Bandwidth:
2.4GHz
(divided over 14 channels, 2400 to 2497 MHz for each channel)
NOTE: The wireless LAN cannot be used together with the Ethernet. The “LAN
Type” setting in the Host Interface menu determines the LAN interface to
be used.
6.3.2 BLOCK DIAGRAM
Detailed
Descriptions
Engine Board
Parallel I/F
LED2 (Orange)
LED1 (Green)
PCMCIA
Card Bus
Controller
CN3
802.11b
PCMCIA Card
CN1
Interface Board
Controller Board
G073D900.WMF
LED Indicators
LED
LED1 (Green)
LED2 (Orange)
SM
DESCRIPTION
Link status
Power distribution
ON
Link success
Power on
OFF
Link failure
Power off
6-5
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
IEEE802.11B (WIRELESS LAN)
6.3.3 TRANSMISSION MODE
The following transmission modes are provided for wireless communication.
Ad hoc Mode
G073D907.WMF
The ad hoc mode allows communication between each device (station) in a simple
peer-to-peer network. In this mode, all devices must use the same channel to
communicate.
In this machine, the default transmission mode is ad hoc mode and the default
channel is 11. First, set up the machine in ad hoc mode and program the
necessary settings, even if the machine will be used in the infrastructure mode.
To switch between ad hoc and infrastructure modes, use the following user tool:
Host Interface Menu - IEEE802.11b - Comm Mode
Infrastructure Mode
Access Point
G073D908.WMF
The infrastructure mode allows communication between each computer and the
printer via an access point equipped with an antenna and wired into the network.
This arrangement is used in more complex topologies.
• The wireless LAN client must use the same SSID (Service Set ID) as the access
point in order to communicate.
G073/G074
6-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IEEE802.11B (WIRELESS LAN)
6.3.4 SECURITY FEATURES
SSID (Service Set ID)
The SSID is used by the access point to recognize the client and allow access to
the network. Only clients that share the same SSID with the access point can
access the network.
NOTE: 1) If the SSID is not set, clients connect to the nearest access point.
2) The SSID can be set using the web status monitor or telnet.
Using the SSID in Ad hoc mode
When the SSID is used in ad hoc mode and nothing is set, the machine
automatically uses “ASSID” as the SSID. In such a case, “ASSID” must also be set
at the client.
NOTE: SSID in ad hoc mode is sometimes called “Network Name.”
Some devices automatically change from ad hoc mode to infrastructure mode
when the same SSID is used in ad hoc mode and infrastructure mode. In such a
case, to use the device in ad hoc mode, use a specified SSID in infrastructure
mode and use “ASSID” in the ad hoc mode.
MAC Address
When the infrastructure mode is used, access to the network can also be limited at
the access points using the MAC address. This setting may not be available with
some types of access points.
SM
6-7
CÓPIA NÃO CONTROLADA
G073/G074
Detailed
Descriptions
WEP (Wired Equivalent Privacy)
WEP is a coding system designed to protect wireless data transmission. In order to
unlock encoded data, the same WEP key is required on the receiving side. There
are 64 bit and 128 bit WEP keys. However, this machine supports only 64 bit WEP.
NOTE: The WEP key can be set using the web status monitor or telnet.
CÓPIA NÃO CONTROLADA
IEEE802.11B (WIRELESS LAN)
6.3.5 TROUBLESHOOTING NOTES
Communication Status
Wireless LAN communication status can be checked with the UP mode “W.LAN
Signal” in the Maintenance menu. This can also be checked using the Web Status
Monitor or Telnet.
The status is described on a simple number scale.
STATUS DISPLAY
Good
Fair
Poor
Unavailable
COMMUNICATION STATUS
76~100
41~75
21~40
0~20
NOTE: Communication status can be measured only when the infrastructure mode
is being used.
Channel Settings
If a communication error occurs because of electrical noise, interference with other
electrical devices, etc., you may have to change the channel settings.
To avoid interference with neighboring channels, it is recommended to change by 3
channels. For example, if there are problems using channel 11 (default), try using
channel 8.
25MHz
Channel
MHz
1
2,412
2
3
4
25MHz
5
6
7
8
9
2,437
10
11
12
13
2,462
G073D901.WMF
G073/G074
6-8
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
IEEE802.11B (WIRELESS LAN)
Troubleshooting steps
Detailed
Descriptions
If there are problems using the wireless LAN, check the following.
1) Check the LED indicator on the wireless LAN card.
2) Check if “IEEE802.11b” is selected in the UP mode LAN Type in Network
Setup in the Host Interface menu.
3) Check if the channel settings are correct.
4) Check if the SSID and WEP are correctly set.
If infrastructure mode is being used,
1) Check if the MAC address is properly set
2) Check the communication status
If the communication status is poor, bring the machine closer to the access
point, or check for any obstructions between the machine and the access
point.
If the problem cannot be solved, try changing the channel setting.
SM
6-9
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
NEW FEATURES
6.4 NEW FEATURES
6.4.1 IP OVER 1394
In addition to IEEE1394 printing, a feature supported in the model G056/G058, this
machine supports IEEE1394 printing by setting an IP address. This feature is
called ‘IP over 1394’.
The former IEEE1394 printing without IP address is known as ‘SCSI printing’.
Software Application
TCP/IP (Virtual) Port
SCSI (Virtual)
Port
IP over 1394
Ethernet
Port
IEEE1394 Port
SCSI Printing
IEEE802.11b
(Wireless LAN)
Port
IP over 1394
Printing
G073D902.WMF
NOTE: 1) Windows XP is the only OS which supports IP over 1394.
2) Windows XP and 2000 supports IEEE1394 SCSI printing.
G073/G074
6-10
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
NEW FEATURES
6.4.2 JOB SPOOLING
Description
Print data can be spooled (stored) in the machine’s HDD, and the machine starts to
print when data transfer is complete. Since the machine stores all data first before
printing, the host computer is freed up more quickly.
NOTE: 1) This feature is only available when an optional HDD is installed in the
machine.
2) The supported print protocols are IPP and LPR.
3) The default setting for this feature is ‘off’. The user must switch it on
using UP mode to enable this feature.
• The size of the HDD partition for job spooling is 500 MB.
• The partition can hold up to 50 jobs.
Related SP Modes
Job spooling can be turned on and off using printer engine service mode “Set
Network” menu separately for each protocol.
“Job spool (LPR)”: Job spooling on/off for LPR.
“Job spool (IPP)”: Job spooling on/off for IPP.
Detailed
Descriptions
The machine does not spool jobs when job spooling is switched off with the SP
mode, even when the customer switches it on with the user mode.
SM
6-11
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
SPECIFICATIONS
1. GENERAL SPECIFICATIONS
Maximum 26 pages per minute (A4/LT LEF)
(20 pages: duplex printing)
Printer Languages:
PCL6/PCL5e
PostScript 3
RPCS (Refined Printing Command Stream: an original Ricoh
PDL)
TIFF (rev 6.0 compatible)
Resolution:
1200 dpi (PCL6/PS3/RPCS)
600 dpi (PCL 6/PCL5e/PS3/RPCS)
300 dpi (PCL 5e/PS3)
Resident Fonts:
PCL:
35 Intellifonts
10 True Type fonts
PS3:
136 fonts (24 Type 2 fonts, 112 Type 14 fonts)
Host Interfaces:
Bi-directional IEEE1284 parallel x 1: Standard
USB 2.0/1.1
Ethernet (100 Base-TX/10 Base-T): Standard for G073
IEEE1394
IEEE802.11b (wireless LAN)
Network Protocols:
TCP/IP, IPX/SPX, NetBEUI, Apple Talk
First Print Speed:
6.5 s or less (A4/LT LEF, standard tray)
Warm-up Time
Less than 12 seconds
(Less than 19 seconds from power on)
Print Paper
Capacity:
Standard tray: 250 sheets
Optional paper tray unit: 500 sheets
(up to two paper tray units can be installed)
Optional by-pass tray: 100 sheets
Print Paper Size:
Maximum: A3/11" x 17"
Minimum:
Standard tray:
A5 LEF
Optional paper tray: A5 LEF
By-pass: A6/ 90 x 148 mm SEF
Specifications
Printing Speed:
(Refer to "Supported Paper Sizes".)
Printing Paper
Weight:
SM
Standard tray:
Optional paper tray:
By-pass tray:
60 to 105 g/m2 (16 to 28 lb.)
60 to 105 g/m2 (16 to 28 lb.)
52 to 162 g/m2 (14 to 43 lb.)
7-1
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
Output Paper
Capacity:
Standard output tray: 250 sheets
Optional 1-bin shift tray: 250 sheets
Optional 4-bin mailbox: 200 sheets total
Memory:
Standard 32 MB, up to 96 MB with optional DIMM
Power Source:
120 V, 60 Hz: More than 10 A (for North America)
220 V - 240 V, 50/60 Hz: More than 6.0 A (for Europe)
Power Consumption:
120V
Maximum
Printing
Energy Saver
940 W or less
650 W or less
22 W or less
230V
940 W or less
650 W or less
22 W or less
Mainframe Only
Full System
64 dB or less
40 dB or less
68 dB or less
40 dB or less
Noise Emission:
Printing
Stand-by
NOTE: The above measurements were made in accordance with ISO 9296 at
the operator position.
Dimensions (W x D x H): 478 x 437 x 305 mm
Weight:
G073/G074
Approximately 18 kg (cartridge included)
7-2
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
1.1
SUPPORTED PAPER SIZES
Paper
Size (W x L)
A3
B4
A4 SEF
A4 LEF
B5 SEF
B5 LEF
A5 SEF
A5 LEF
A6 SEF
Ledger
Legal
Letter SEF
Letter LEF
Half Letter SEF
Half Letter LEF
Executive SEF
Executive LEF
F
Foolscap
Folio
Com10 Env.
Monarch Env.
C6 Env.
C5 Env.
DL Env.
8K
16K SEF
16K LEF
Custom
297 x 420 mm
257 x 364 mm
210 x 297 mm
297 x 210 mm
182 x 257 mm
257 x 182 mm
148 x 210 mm
210 x 148 mm
105 x 148 mm
11 x 17”
8.5 x 14“
8.5 x 11”
11 x 8.5”
5.5 x 8.5”
8.5 x 5.5”
7.25 x 10.5”
10.5 x 7.25”
8 x 13”
8.5 x 13”
8.25 x 13”
4.125 x 9.5”
3.875 x 7.5”
114 x 162 mm
162 x 229 mm
110 x 220 mm
267 x 390 mm
195 x 267 mm
267 x 195 mm
Minimum:
90 x 148 mm
Maximum:
297 x 432 mm
Paper Trays
Main Unit/Option
US
Eur/Asia
#
Y /Y
Y/Y
# #
# #
Y /Y
Y /Y
#
Y /Y
Y/Y
Y/Y
Y/Y
# #
# #
Y /Y
Y /Y
# #
# #
Y /Y
Y /Y
N
N
# #
#
Y /Y
Y/Y
N
N
#
Y/Y
Y /Y
#
Y/Y
Y /Y
Y/Y
Y/Y
Y/Y
Y/Y
N
N
N
N
#
#
N/Y
N/Y
# #
# #
Y /Y
Y /Y
# #
# #
Y /Y
Y /Y
#
# #
Y/Y
Y /Y
# #
# #
Y /Y
Y /Y
N
N
N
N
N
N
N
N
N
N
# #
# #
Y /Y
Y /Y
# #
# #
Y /Y
Y /Y
# #
# #
Y /Y
Y /Y
C
By-pass
Tray
C
N/Y
N/Y
Env.
Feeder
Duplex
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
C
Y
#
Y
#
Y
#
Y
#
Y
#
Y
N
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
Y
#
N
N
N
Y
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
#
Y
#
Y
#
Y
#
Y
#
Y
N
N
N
Y
Y
Y
Y
Y
Y
N
Y
N
Y
Y
Y
Y
N
N
N
Y
Y
Y
Y
N
N
N
N
N
Y
Y
Y
C
N
N
Y
Y
Y#
YC
N
SM
Supported. The paper size sensor detects the paper size.
Supported. The user has to select the correct paper size for the tray.
Supported. The user has to enter the width and length of the paper.
Not supported.
7-3
CÓPIA NÃO CONTROLADA
G073/G074
Specifications
Remarks:
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
2. SOFTWARE ACCESSORIES
The printer drivers and utility software are provided on one CD-ROM. An auto-run
installer allows you to select which components to install.
2.1
PRINTER DRIVERS
Printer Language
PCL 6
PCL 5e
PS3
RPCS
Windows
95/98/ME
Yes
Yes
Yes
Yes
Windows NT4.0
Yes
Yes
Yes
Yes
Windows
2000/XP
Yes
Yes
Yes
Yes
Macintosh
No
No
Yes
No
NOTE: 1) The printer drivers for Windows NT 4.0 are only for the Intel x86
platform. There is no Windows NT 4.0 printer driver for the PowerPC,
Alpha, or MIPS platforms.
2) The PS3 drivers are all genuine AdobePS drivers, except for Windows
2000, which uses Microsoft PS. A PPD file for each operating system is
provided with the driver.
3) The PS3 driver for Macintosh supports Mac OS 8.1 or later versions.
2.2
UTILITY SOFTWARE
Software
Agfa Font Manager
(Win 95/98/Me, NT4, 2000)
SmartNetMonitor for Admin
(Win 95/98/Me, NT4, 2000,
XP)
SmartNetMonitor for Client
(Win95/98/Me, NT4, 2000,
XP)
1394 Utility (rm1394pr.exe)
(Win 2000, XP)
Printer Utility for Mac
(Mac OS 8.1 or later)
G073/G074
Description
A font management utility with screen fonts for the printer.
A printer management utility for network administrators. NIB
setup utilities are also available.
A printer management utility for client users.
A 1394 utility removes all IEEE1394 port and printer information
from the Windows registry.
This software provides several convenient functions for printing
from Macintosh clients.
7-4
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
3. MACHINE CONFIGURATION
3.1
SYSTEM COMPONENTS
[D]
[C]
[B]
[A]
[E]
G073V107.WMF
Item
Machine Code
G073
G074
No.
Option
Duplex Unit
4-bin Mailbox
1-bin Shift Tray
Paper Tray Unit
G552
G553
G554
G555
B
C
D
E
Envelope Feeder
G556
E
Others
Maintenance Kit
G770
Main Unit
A
Remarks
G073: Standard onboard NIB
Up to two tray units can be installed.
When two paper tray units are
installed, it must be installed in the
upper unit.
Specifications
NOTE: All the above items are user installable.
SM
7-5
CÓPIA NÃO CONTROLADA
G073/G074
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
3.2
INTERNAL OPTIONS
[J]
802.11b
PCMCIA Card
I/F Board
Optional NIB
[F]
IEEE1394 Board
[G]
USB I/F
[I]
CN1
CN2
Ethernet I/F
(standard for G073 model)
Parallel I/F
CN5 (SLOT1)
Memory DIMM
CPU
CN4
Controller Board
NVRAM
IC Card I/F
SIMAC
HDD Unit
[H]
G073V900.WMF
Internal Options
F
NIB
G646
IEEE1394
HDD
Memory 64 MB
Wireless LAN
(IEEE802.11b)
G336
G575
G579
G
H
I
G628
J
New option for this model (for G074
only; G073 has one built-in)
New option for this model
New option for this model
Table of Available Interfaces
G073 Model
G074 Model
Standard I/F
USB
IEEE1284
Ethernet
USB
IEEE1284
Optional I/F
IEEE1394
IEEE802.11b
Ethernet
IEEE1394
IEEE802.11b
Remarks
Either optional
interface can be
installed.
One of these optional
interfaces can be
installed.
NOTE: The G073 model has an on-board Ethernet interface.
G073/G074
7-6
CÓPIA NÃO CONTROLADA
SM
CÓPIA NÃO CONTROLADA
SPECIFICATIONS
4. OPTIONAL EQUIPMENT
Specifications
All of the following options are also used with the base model (G056/G058). Please
refer to the base model service manual for specifications.
• Paper Tray Unit
• Envelope Feeder
• Duplex Unit
• Four-bin Mailbox
• One-bin Shift Tray
SM
7-7
CÓPIA NÃO CONTROLADA
G073/G074