E-TON ROVER GT Owner`s manual

E-TON
ROVER & ROVER GT
OWNER’S MANUAL
ROVER
ROVER GT
E-TON E-Copyright
TON ©2008-2009
E-TONETONEAmerica,
-TONall rights
E-reserved.
TON E-TON E-TON
E-TON
ROVER
C
O
N
F
I
G
U
R
A
T
I
O
N
S
Rover (Safety Nets)
Rover (Brush Guards)
Rover GT
Copyright ©2008-2009 ETON America, all rights reserved.
Important Notices
READ and UNDERSTAND this owner's manual
Both the operator and the adult supervisor should completely read and understand this
owner's manual before operating this vehicle. This owner's manual will instruct you in the safe
operation of the vehicle.
NO Passengers
This vehicle was designed for operation ONLY by the operator, (Driver). The load limit
and seat configuration is designed for the operator ONLY. It is not safe to carry passengers on
the vehicle.
ADULT Supervision and Instruction are REQUIRED.
This vehicle MUST NOT be operated by a youth without adult supervision and
Instructions. Unattended operation without adult supervision could result in injuries. E-TON
recommends that both the operator and the adult supervisor attend an vehicle safety instruction
course.
ALWAYS Wear Protective Clothing
While operating this vehicle, the driver must always wear protective clothing. Protective
helmet with face shield, elbow and knee pads, long leg pants, gloves and hard soled boots
Should always be worn when operating this vehicle.
OFF ROAD USE ONLY
This vehicle is designed and manufactured for off-road use only. Operation on public
streets, roads or highways is illegal and very dangerous.
OBEY all State and local laws and regulations
Each state and local governing agency has laws and regulations for vehicle operations.
It is the owner's responsibility to know, understand and obey these laws and regulations.
SPEED RESTRICTION Devices
This vehicle is equipped with electronic speed limiting devices. Any attempt to change,
over-ride or bypass these devices may cause dangerous operating conditions.
Copyright ©2008-2009 ETON America,
Pageall
1 rights reserved.
TABLE OF CONTENTS
Manual Choke Knob
Throttle Pedal
Brake Pedal
Parking Brake Lever
Fuel System
3
7
7
7
7
9
9
9
10
10
10
11
Fuel Tank
Fuel Valve
Inline Fuel Filter
The Seat
Engine Oil
12
13
SAFETY NOTES
SERIAL NUMBER
Vehicle Identification Number
DESCRIPTION
Controls, Switches & Feature Locations
CONTROL FEATURE
Key Switch
Checking Engine Oil Level
Transmission Gear Selector
Dashboard Indicators
Tires And Wheels
Tire & Wheel Inspection
Tire Pressure
SPECIFICATIONS
MAINTENANCE
Air Filter
To Clean The Filter
Braking Systems
The Brake Hoses Inspection
Filling The Brake Fluid Reservoir
Purging Brake Line
Parking Brake Ajustment
13
14
14
15
17
17
18
Drive Chain
Chain Slack Adjustmen
20
Throttle Pedal
Adjusting The Throttle
Electrical Battery
Changing Engine Oil
Changing Transmission Oil
Spark Plug
Spark Arrester Screen
20
Maintenance Schedule
Owners Maintenance Records
OPERATION
RIDING TIPS
WIRING DIAGRAM
MANUFACTURE'S WARRANTY
Copyright ©2008-2009 ETON America,
Pageall
2 rights reserved.
21
22
22
23
23
24
24
25
26
27
29
SAFETY NOTES
1. Both the adult supervisor and youth operator must fully understand everything in this manual
before operating this vehicle.
2. This vehicle was designed for the operator only. NO PASSENGERS should be allowed on
this vehicle.
3. This vehicle is designed for operation on level, obstacle free off-road areas.
4. Riding this vehicle on public roads or highways is illegal. If it becomes necessary to cross a
public road or highway, the vehicle should be pushed across using extreme caution.
5. This vehicle MUST NOT be operated without adult supervision and instruction.
6. DO NOT operate this vehicle while under the influence of drugs, alcohol or other medication
that impairs judgment or coordination. Doing so can result in serious injury or even death.
7. Maintain a safe distance between your vehicle and other vehicles with whom you are riding.
8. The driver must tie the safety belt (and button the safety nets).
9. Always use both hands for steering.
10. Avoid wheelies and jumping. You may lose control of the machine or overturn.
11. READ the owner's manual carefully
before riding.
12. ALWAYS wear a helmet, face shield,
elbow & knee pads, hard-soled boots,
gloves, and protective clothing while
operating this vehicle.
Copyright ©2008-2009 ETON America,
Pageall
3 rights reserved.
SAFETY NOTES
13. NEVER ride this vehicle unless it has
been properly maintained and adjusted.
Always perform a pre-ride inspection
of your vehicle. Look for wires, bolts
and other fastener that may have come
loose onprevious rides. Inspect the drive
chain, throttle and brakes for proper
adjustment and operation.
Check the engine oil level in the oil tank.
Check fuel level and inspect for fuel
leaks.
(Remember, you can ride further in 1
hour than you can walk back in 1 day!)
14. WARN UP your body with some
exercises before riding.
This helps to make you alert and prevent
cramping and other discomfort.
15. LEARN TO RIDE this vehicle properly
and safely. Have an experienced rider
teach You the safe operation of your
vehicle. E-TON recommends you take
an vehicle riding course before you first
ride your vehicle.
Copyright ©2008-2009 ETON America,
Pageall
4 rights reserved.
SAFETY NOTES
16. NEVER REFUEL this vehicle when hot.
Ask your adult supervisor to refuel your
vehicle.
Gasoline is extremely flammable and
will ignite if spilled on a hot engine or
muffler. Never smoke or expose the
fuel to an open flame or spark while
refueling your vehicle.
Always refuel your vehicle in a safe
place free of any ignition source.
17. NEVER run the vehicle in an enclosed
area.
The exhaust gases from the engine
contain CARBON MONOXIDE which can
be fatal if breathed in high concentrations
for an extended time.
18. HOT! The engine and exhaust system on
your vehicle become very hot during
normal operation. Touching these hot
surfaces can cause sever burns.
Always assume that your units engine
and exhaust system are HOT unless
you know that they are not.
Copyright ©2008-2009 ETON America,
Pageall
5 rights reserved.
SAFETY NOTES
Additional safety tips:
Participate in an approved the vehicle safety education training program
Always provide responsible adult supervision for the vehicle operators younger than 18
years of age
Don't let youngsters ride full-sized vehicles
Follow all safety recommendations of the vehicles manufacturer
Operate the vehicles only during daylight
Wear a helmet with face protection at all times
Operate only four-wheeled vehicles
Provide a drug and alcohol free environment
Always use the buddy system
Avoid riding in areas where contact with automobiles might be possible
Drive the vehicle on surfaces as recommended by the manufacturer
Travel at speeds conducive to conditions and operator abilities
Check on the conditions of the trails you will be traveling
Know and understand local and state laws governing the use of the vehicles
Permit only one operator per the vehicle
Insist on a "perfect fit" between the vehicle and the physical, mental, and emotional maturity
of the operator
Use antenna flags and wear bright clothing to increase conspicuity.
Use maps and compass if you are riding in an unfamiliar area.
Make a mental note of landmarks; you may need them if you are stranded.
If you are lost at night, do not move around. You will waste valuable fuel that you can use to
ride safety in the daylight.
Carry a first-aid pack with you.
Carry some snacks and a water supply with you.
Carry equipment to handle medical and mechanical emergencies.
Your vehicle field repair kit should include the following items;
® the manufacturer's tool kit
® wire, tape, elastic cords,
® possibly locking pliers
® and a towrope.
Pre-Ride Inspection - Inspecting the condition of your vehicle before each ride is very
important to minimizethe chance of injury and maximize the enjoyment of your ride. It also
helps ensures long term performance of your Vehicle. Follow the owner's manual guide to
inspection and maintenance of your Vehicle.
A well maintained the vehicle will give you years of enjoyment.
Watch out for thin ice which may be camouflaged by snow.
Remember, you can ride further in one hour than you can walk in an entire day.
Copyright ©2008-2009 ETON America,
Pageall
6 rights reserved.
Vehicle Identification Numbers
Engine serial number
is located on the left-hand side of the
engine on the crankcase housing.
Vehicle Identification Number (VIN)
is located at the right of the frame
and approaches the front wheel.
YOUR VIN
Eng. No.
Controls, Switches & Feature Locations
Locations of controls and features
4. Brake Pedal
5. Throttle Pedal
6. Parking Brake Lever
1. Key Switch
2. Steering Wheel
3. Horn Button
3
2
1
6
4
5
Copyright ©2008-2009 ETON America,
Pageall
7 rights reserved.
Controls, Switches & Feature Locations
Locations of controls and features
11. Speedometer & Odometer
Fuel Indicator Meter(for ROVER GT)
7. Auxiliary 12v DC Electrical Outlet
8. Brake Oil Reservoir
9. Manual Chocke Knob
12. Transmission Gear Selector
& Reverse Indicator Lamp
10. Compass Ball(for ROVER GT)
8
9
11
10
12
7
7
Only for ROVER GT
13. Front Cargo Box
14. Fuel Tank Filler And Vent tube
15. Rear Cargo Box
14
13
14
15
ROVER
13
15
ROVER GT
Copyright ©2008-2009 ETON America,
Pageall
8 rights reserved.
CONTROL FEATURE
Key Switch
Manual Chocke Knob
A - OFF Position - With key in off position,all
switched power is off,and engine should not
run.
The vehicle are equipped with a manually
operated carburetor choke system.
This choke is operated by the knob at the
left side of the dashboard.
The engine choke knob is used to enrich
the fuel mixture when starting the engine
from a cold start.
When first starting the engine,(cold start),
place the knob in the full up position,(Choke
closed or on) After allowing the engine to
warm up for 15-20 seconds, slowly move
the knob back to the normal until the engine
idles down runs smooth.The knob to the full
down is the normal operation position.(Choke
open or off).
B - ON Position - Turn key from off to the position
and all switched power circuits will be energized.
C - START Position - Turn key to start position
to start the engine .Release key after engine
has started and it will automatically return to
the on position.
The engine will continue to run.
Only For ROVER
This vehicle is equipped with a long key and a
short key.
A limited speed with Max 7 mile is controled by
the short key.
A limited speed is controled by the long key and
(C.D.I.) with 4different kind of speed.(9.3,12.4,
15.5 & 18.6 mile)
C.D.I is located in front cargo box.
NOTE: Your unit includes an electronic speed
control (C.D.I) that is set to limit the maximum
speed of the unit to the standards set by the
CPSC for the age of the rider the unit was
designed for.
Copyright ©2008-2009 ETON America,
Pageall
9 rights reserved.
CONTROL FEATURE
Throttle Pedal
Brake Pedal
This vehicle is equipped with dual front hydraulic
discl brakes and a rear hydraulic disc brake.
The four wheel simultaneously brakes are
operated by pushing the foot brake pedal.
The throttle pedal is located on the under of
the dashboard of the right. To operate the
throttle pedal, place your sole of the right
foot on the pedal and press down to increase
your speed.To decrease your speed, reduce
your pressure on the pedal and the spring
tension will automatically reduce your speed.
Parking Brake Lever
Parking On
Parking Off
The parking brake is shown on the picture.
The position of parking Off is on the full
down position.Turn parking brake to the
full up position is parking On.
This should be engaged as a parking brake
whenever the vehicle is not in operation.
Copyright ©2008-2009 ETON America,
Pageall
10 rights reserved.
CONTROL FEATURE
Fuel System
over tighten. Over tightening the cap can
cause damage to the cap or seal.
Fuel Tank
The fuel tank capacity is 11 liters, 2.9gal,
including a reserve of 2 liters, 0.5gal.
The fuel tank fill cap is located on top of the
back of the seat.
Use regular unleaded automobile gasoline
with an octane level of 91 or higher.
NEVER REFUEL YOUR vehicle when the
engine is HOT. Wait 30 minutes after turning
off the unit before refueling. Spilling fuel on
a HOT engine could cause a fire. Wipe up
any fuel spills before re-starting.
ROVER
Fuel Valve
ROVER GT
The cap contains a vent to prevent a vacuum
from forming in the tank as fuel is used.
The vent tube must be attached to the cap
and Inserted in the vent tube holder hole
while operating the unit.
The fuel cap vent and vent tube must be
clean and clear of obstructions for the unit to
operate normally. You can check the vent and
vent tube by blowing air through the tube. If
you can not blow through the vent tube and
cap you must clean the vent and tube or
replace them.
Every time you refuel your unit, check the
rubber seal inside the cap for cuts, tears and
dirt. Clean or replace the seal if it becomes
warn or torn. the seal must be in good
condition to insure a proper seal of the cap to
the tank to prevent fuel spills. DO NOT allow
dirt or other debris to enter the tank when
refueling.
Replace the cap if damaged or if it will not
seal to the tank.
Tighten the cap snugly, being careful not to
The unit is equipped with a three way fuel
valve located on the left side of the unit just
below the seat.
The valve has three settings; "OFF", "ON"
and "RES". With the valve in the "OFF" position
fuel is held in the tank and is prevented from
flowing to the carburetor. The valve should be
placed in the "OFF" position whenever the
unit is not being operated. Place the valve in
the "ON" for normal operation of the unit.
This allows fuel to flow to the carburetor for
normal operating. The "RES" position allows
fuel to flow from the small reserve in the tank
to allow the unit to be taken to a refueling
location.
When you have to switch to the "RES" position
you must refuel the unit as soon as possible.
ALWAYS CHECK YOUR Fuel level before
you start riding your vehicle. Remember:
You can drive further in one hour on your
Vehicle than you can walk in one day.
Copyright ©2008-2009 ETON America,
Pageall
11 rights reserved.
CONTROL FEATURE
Inline Fuel Filter
This vehicle is equipped with an inline fuel
filter to prevent dirt and debris from entering
the carburetor and engine.
Check the filter for dirt or damage before
each ride and at each refueling. Replace
the filter if dirty or damaged.
The filter should be replaced every 600
hours of operation and at the start of each
season.
To replace the filter, first turn the fuel valve
to the "OFF" position.
Then carefully compress the wire clamp
rings until the clamp is free of the fuel line.
Slide each clamp away from the filter about
3/4".
The Seat
You can change the position of sest and
head rest to make a comfortable position
of you.
To change the seat position, you need to
lossen two bolts at the seat bottom right
hand side.
Only For ROVER
(CEILING)
To move the head rest, you need to take
out the bolts.
Move the head rest to a correct position,
then tighten the bolts.
Remove the filter from the fuel line by holding
the line and pulling the filter. Install the new
filter by inserting the filter into the fuel line
Turn the fuel valve to the "ON" position and
returning the clamps to the original position.
check for leaks. Inspect the fuel lines for
cuts, abrasions and deterioration. Replace
fuel lines as needed.
DO NOT operate or start the engine if the
fuel filter or lines are leaking. Leaking fuel
can cause a fire.
Copyright ©2008-2009 ETON America,
Pageall
12 rights reserved.
CONTROL FEATURE
Engine Oil
Transmission Gear Selector
Checking Engine Oil Level
Engine Oil
Dip Stick
And fill tube
This vehicle uses automotive type engine
oil to lubricate the engine. The engine oil
dip stick is located on the right-hand side
of your engine.
To check your oil level, remove the dip stick
by turning the thumb hold counter clockwise
until the stick has been completely disengaged
from the threads. Pull the dip stick out of
the crank case and check the level of the
oil as Indicated on the dip stick. The engine
oil is full when the oil reaches the level on
the stick as Indicated in the photo above.
Always check your engine oil level with the
engine off and cold. Removing the dip stick
with the engine running could cause hot
oil to splash from the crankcase causing
severe burns.
Checking your engine oil while the engine
is hot can give you a false reading; always
check the oil level with a cold engine.
Your engine requires SAE 15W/40 engine
oil and the crankcase capacity is 0.9 Liters
/ 0.9 quart.
The engine oil should be changed before
the start of each riding season or every 300
hours of operation. When riding where
conditions are dusty or humidity is high the
engine oil should be change more frequently.
The vehicle is equiped with a transmission
gear selector switch mounted on the dashboard. The switch has three positions ("R",
"N","F").
"R" = Reverse
"N" = Neutral
"F" = Forward
The selector must be placed on "N" to
start the engine. Once the engine is started,
engine the brake lever and move the slector
switch to the desired direction of travel.
Always be sure the vehicle has come to
a complete stop and the brake lever is fully
engaged before turning the selector switch.
Always pause in the "N" neutral positon
for a few seconds when shifting from forward
to revers or from revers to forward, this
allows the transmission time to disengage
and resycronize.
NOTE!
For your safety and protecting the engine,
you must wait the indicator light bright
(white color) when you shift to forward or
reverse. The engine will be shut down if
the engine speed is high.
DO NOT SHIFT GEAR when you drive
downhill.
Copyright ©2008-2009 ETON America,
Pageall
13 rights reserved.
CONTROL FEATURE
Dashboard Indicators
Tires And Wheels
1
3
2
It is digital LCD meter and displayed in cold
light can applicable to night.
(1)Speedometer digital follow the vehicle's
speed to change digital.
(2)Odometer digital is follow the vehicle's
ride distance to change mileage .
(3)Fuel indicator to"F"when the tank is full,
and to"E"when empty.(And the ROVER.
Of the oil gauge flashes when 3-4 stages
left.)
Auxiliary 12v DC
Electrical Outlet
Power outlet do not use high power electric
equipment to avoid dead battery.
Please foll theowing the regulation list
below.
SUPPORTING POWER
Brake Condition Brake Brake
off
on
Speed
0W 19W
Idle
45W 75W
over 15 km/h
Tire & Wheel Inspection
It is important to inspect your tires and
wheels for damage and wear before each
riding session. Inspect each tire for cuts,
tears and punctures. Inspect the wheel rim
for dentsand separation of the wheel from
the tire bead. Replace any tire or wheel
found to be damaged.
Operating your vehicle with damaged tires
or wheels is dangerous.
Damaged tires or wheels can result in a
sudden loss of tire pressure and control
which could result in injuries.
Check your tire pressure before each riding
session and at each refueling operation.
Always check the pressure when the tires
are cool. Use the tire pressure gauge that
came with Your vehicle to check the tire
pressure.
Tire Pressure
Recommended tire pressure is:
3.2psi / 0.23kg/cm2
Min
Front
4.0psi / 0.28kg/cm2
Max
3.2psi / 0.23kg/cm2
Min
Rear
4.0psi / 0.28kg/cm2
Max
Wheel Nut torque 24-30 N/m (18-22 lb/ft)
Copyright ©2008-2009 ETON America,
Pageall
14 rights reserved.
ROVER
Engine
Four cycle air cooled (EPA Compliant) SOHC
Type
Displacement
88.4cc
Bore / Stroke
φ47.0 * 51.0mm
Compression Ratio / Pressure
10.2 : 1 / 120-140psi
Torque / BHP
6.5N ms @ 6500rpm / 4.8BHP
EPA Approved
Meet or exceeds EPA clean air requirements and CA Green Sticker
Spark Plug
Recommended: NGK CR7HSA/NGK or Nipendenso U22FS-U
Electrode Gap
0.6-0.7mm or 0.023”
Starting
Electrical starter
Transmission
Type
Automatic (C.V.T. V-Belt) with forward/reverse shift
Chassis
Overall Length-Width-Height
1766mm / 69.9" - 1020mm / 40.2" - 1675mm / 65.9"
Wheel Base
1108mm / 43.6"
Seat Height
700mm / 26.6"
Dry Weight
162 kg / 356 lbs
Suspension
Front
Swing A-arm with dual Adjustable Shocks
Rear
Swing Arm with Adjustable Shock
Brakes
Front
Dual Hydraulic Disc
Rear
Hydraulic Disc
Tires
Front
18/7-10
Rear
18/8-10
Min
3.2psi / 0.23kg/cm2
Front
Max
4.0psi / 0.28kg/cm2
Tire Pressure
Min
3.2psi / 0.23kg/cm2
Rear
Max
4.0psi / 0.28kg/cm2
Wheels
Front
4 x 110mm (P.C.D.)
Bolt Pattern
Rear
4 x 110mm (P.C.D.)
Carburetor
Make/Size
SVR 22mm with Manual Choke
Main Jet
0.95mm
Pilot Jet
0.32mm
Air Mixture Adjustment
Back out 1½ - 1 ¾ turns
Idle Speed
Idle 1700 - 1900rpm
Sprockets
Front
520x12t
Rear
520x32t
Chain
#520
Battery
Jell Acid (Maintenance Free)
12V-4AH/AH - GTX5L
Fluids
Type
Unleaded Gasoline 92 octane
Fuel
Volume
11liters / 2.9gal
Type
SAE 15W-40
Engine Oil
Volume
0.9liters / 0.23gal
Type
SAE 80W-90
Transmission
Volume
300cc / 10.2oz
Copyright ©2008-2009 ETON America, all rights reserved.
ROVER
Sprockets
Front
Rear
Chain
Battery
Jell Acid (Maintenance Free)
Fluids
Type
Fuel
Volume
Type
Engine Oil
Volume
Type
Transmission
Volume
Safety Features
Speed Control
Remote Stop Switch
Safety Catch Netting
Seat Belt
Carrying Capacity
Maximum Rider Weight
Additional Features
Rear Cargo Bed
520x12t
520x32t
#520
12V-4AH/AH - GTX5L
Unleaded Gasoline 92 octane
11liters / 2.9gal
SAE 15W-40
0.9liters / 0.23gal
SAE 80W-90
300cc / 10.2oz
Ignition Key Speed Control (Standard)
Remote Engine Stop Switch (Optional)
Rider compartment Safety Netting (Standard)
Lap Belt (Standard)
86.2kg / 190 lbs
Accessory Power Outlet
Covered Front Storage Compartment Foot peddle throttle and brakes controls
Sporty Split Steering Wheel
Dash mounted Forward / Reverse Shift Knob
Adjustable Head Rest
Optional Floor mat and bed liners
Copyright ©2008-2009 ETON America, all rights reserved.
ROVER GT
Engine
Type
Displacement
Bore / Stroke
Compression Ratio / Pressure
Torque / Power
EPA Approved
Spark Plug
Electrode Gap
Starting
Transmission
Type
Chassis
Overall Length-Width-Height
Wheel Base
Seat Height
Dry Weight
Suspension
Front
Rear
Brakes
Front
Rear
Tires
Front
Rear
Four cycle air cooled (EPA Compliant) SOHC
88.4cc
φ47.0 * 51.0mm
10.2 : 1 / 120-140psi
6.1N ms @ 4000rpm / 6.4Ps/8000rpm
Meet or exceeds EPA clean air requirements and CA Green Sticker
Recommended: NGK CR7HSA/NGK or Nipendenso U22FS-U
0.6-0.7mm or 0.023”
Electrical starter
Automatic (C.V.T. V-Belt) with forward/reverse shift
2110mm / 83.0" - 1000mm / 39.4" - 1110mm / 43.7"
1375mm / 54.1"
710mm / 28.0"
185 kg / 407.9 lbs
A-arm with dual Adjustable Shocks
Swing Arm with Adjustable Shock
155mm Dual Hydraulic Disc
175mm Hydraulic Disc
18/7-10
18/8-10
3.2psi / 0.23kg/cm2
4.0psi / 0.28kg/cm2
3.2psi / 0.23kg/cm2
4.0psi / 0.28kg/cm2
Min
Max
Tire Pressure
Min
Rear
Max
Wheels
Front
4 x 110mm (P.C.D.)
Bolt Pattern
Rear
4 x 110mm (P.C.D.)
Carburetor
Make/Size
SVR 22mm with Manual Choke
Main Jet
0.95mm
Pilot Jet
0.32mm
Air Mixture Adjustment
Back out 1½ - 1 ¾ turns
Idle Speed
Idle 1700 - 1900rpm
Sprockets
Front
520x12t
Rear
520x32t
Chain
#520
Battery
Jell Acid (Maintenance Free)
12V-5AH - GTX5L
Fluids
Type
Unleaded Gasoline 92 octane
Fuel
Volume
11 liters / 2.9gal
Type
SAE 15W-40
Engine Oil
Volume
0.9liters / 0.23gal
Type
SAE 80W-90
Transmission Copyright ©2008-2009 ETON America, all rights reserved.
Volume
300cc / 10.2oz
Front
ROVER GT
Safety Features
Seat Belt
Lap Belt (Standard)
Remote Stop Switch
Carrying Capacity
Remote Engine Stop Switch (Optional)
Maximum Rider Weight
Additional Features
Rear Cargo Flat Bed (Standard)
100kg / 200 lbs
Digital dash gauge—Speedometer & Fuel Level (Standard)
Covered Front Storage Compartment Dash mounted F/R Shift Knob & indicator lights (Standard)
(Standard)
Sporty Steering Wheel
Rear Cargo Basket (Optional)
Detachable Spot Light (Optional)
Trailer Hitch &Accessory Power Outlet (Optional)
Foot peddle throttle & brakes controls (Standard)
Front Cargo Rack (Optional)
Carpeted floor mat (Optional)
Copyright ©2008-2009 ETON America, all rights reserved.
Air Filter
To maintain the highest performance from
your engine and to reduce excessive wear
that could cause engine failure the engine
requires a continuous flow of clean air. air
is taken into the engine through an air filter
to clean the air prior to mixing it with fuel
and oil in the carburetor.
Remove the air filter box cover.
Remove the filter element from the air box
as shown in picture.
The filter
During normal operation the filter accumulates
dirt from the air and will need to be cleaned
to maintain the proper air flow. The filter
should be cleaned every 30 days, more often
if you ride in a dusty or dirty environment
and the element should be replaced every
year.
The air filter box is located on the left of
the engine under the set.
It is a black rectangular box.
To Clean The Filter
Remove head protector cover.
Wash the element in a non-flammable
solvent such as air-filter cleaner from your
local auto parts dealer.
1. Dry the element completely before continuing.
2. Soak the element in clean engine oil until
completely saturated.
3. Squeeze out the excess oil until the
element does not drip any oil.
4. Allow the element to dry then reinstall
the element and cover.
Copyright ©2008-2009 ETON America,
Pageall
17 rights reserved.
Braking Systems
The vehicle is equipped with dual front
hydraulic disc brakes and a rear hydraulic
disc brake.
The four wheel simultaneously brakes are
operated by pushing the foot brake pedal.
Proper maintenance of the brake system is
a necessary part of safe operation of your
unit. The brake systems should be inspected
and tested before each riding session.
Hose
The front brakes
Hose
The Brake Hoses Inspection
Visually inspect the brake hose for any
signs of wear or leaks. Check the fluid level
in the fluid reservoir by checking the position
of cup on the left side of the dashboard.
The fluid level should fill at least 3/ 4 of the
cup when the unit is setting on a level
surface.
The rear brake
After riding your unit, be sure to clean any
build up of mud, sand and dirt from the brake
rotor skid plate. This will protect the rotor
disc from rust and corrosion.
Filling The Brake Fluid Reservoir
Remove the reservoir cover.
Test the brakes by applying pressure to the
brake pedal and trying to push the unit
forward. if the wheel rotates while the brakes
are applied, check your fluid level and brake
pads. If the brake pedal feels spongy or
does not stop when squeezed, you may
have air in the lines. All air must be purged
from the brake lines for the disc brake to
operate properly. (See purging brake lines).
Cover
Fill the reservoir to 1/8" from top with Dot-3
SAE-J 1703 grade brake fluid.
Copyright ©2008-2009 ETON America,
Pageall
18 rights reserved.
For the hydraulic brake system to operate
safely, the brake system must be purged
of air in the lines and reservoir.
To bleed the air will require two people to
perform the following procedure.
Fill to 1/8"
from top
Caution: DO NOT Allow dirt to fall into the
reservoir
Refold the cover gasket as shown in picture
and replace cover.
Purging Brake Lines
1. Place a drain pan under the brake caliper
to catch the fluid.
2. Open the bleeder valve1/ 2 turn counter
clockwise.
3. Squeeze the brake lever to expel air
from the system.
4. While holding the brake lever, close the
bleeder valve.
5. Repeat steps 2 through 4 until the brake
fluid coming from the bleeder valve is a
solid stream without any air, then close
the valve and replace rubber protection
cap.
6. Test the brake system by squeezing the
lever, the lever should feel firm and stop
without fading.
Purging Brake Adjustment
As you found out the parking brake which
has been decreased its brake ability, You
must adjus the parking brake, Turn the
adjustment nut of the parking brake to
adjust Parking Brake.
Bleecler Valve
THE FRONT CALIPER
Bleecler Valve
THE REAR CALIPER
Copyright ©2008-2009 ETON America,
Pageall
19 rights reserved.
Drive Chain
Throttle Pedal
The drive chain will stretch with use and
will require periodic adjustments. To check
the chain tension, remove the chain guard
and measure the slack.
The amount of slack in the chain should not
exceed 5-10mm or 0.2" - 0.4". Inspect the
drive and axle sprockets for worn, damaged
or broken teeth. Replace as needed. Inspect
the chain links for damaged, worn or loose
rivets. Repair or replace asneeded
The throttle pedal is located on the under
of the dashboard of the right and is operated
by using the sole of the right foot. The
pedal is spring loaded and will return to
the idle position when you remove your
sole of the right foot from the pedal. To
accelerate the unit, simply press the pedal
down to open the throttle slide in the
carburetor. to slow the unit, reduce the
pressure on the pedal or remove your
sole of the foot and the throttle will return
to the idle position automatically.
Chain Slack Adjustment
Adjusting The Throttle
Axle Postion
Lock Bolts
Chain Tension
Adjuster
Loosen the axle position lock bolts lightly and
turn the chain adjuster nut to take up the excess
slack in the chain. Once the chain has been
adjusted to the proper tension retighten the
axle position locking bolt.
The chain should be kept well lubricated to
prevent excess wear and premature failure.
We recommend that you lubricate the chain
every 15 hours of operation, or more frequently
if needed, with a high quality chain lubricant.
The cable should be adjusted to allow for
1/8" free travel before the throttle engages
the carburetor throttle slide. To adjust the
cable's free travel, loosen the locking nut
of the cable adjuster, and turn the adjuster
wheel until there is 1/8" free travel in the
lever. Tighten the locking nut to secure the
adjusting ring.
Copyright ©2008-2009 ETON America,
Pageall
20 rights reserved.
Electrical Battery
The unit's battery is located the left-hand
side of the seat and supplies electrical power
to the unit.
The battery is a 12 volt jell acid type that
contains no liquid electrolyte. The battery
should be removed from the vehicle when
stored for extended periods and charged
before being replaced in the unit.
Use a trickle charger set at 12 volts to
recharge the battery to full charge before
replacing it in the unit.
Amperage Color
Rating
Red
10A
10A
Red
Series Items
Battery
Battery
Optional
7.5A
Brown Power Oulet
7.5A
Brown Optional
Power Oulet
For anothers series items of electrical units,
please refer to the fuse as shown in list.
When reinstalling the battery, be sure to
connect the red cable to the positive (+)
terminal and the black cable to the negative
(-) terminal.
The battery should be replaced every three
years or when it no longer holds a charge.
Do not expose the battery, for extended
periods of time, to freezing temperatures.
If the battery has been frozen it will need
to be replaced. There are inline fuses on
the positive protect the wiring system from
over loads. If your lead of the battery to
starter motor will not turn over and the
battery is fully charged, check the inline
fuse on the unit.
Copyright ©2008-2009 ETON America,
Pageall
21 rights reserved.
Changing Engine Oil
Changing Transmission Oil
1. Place an oil catch pan under the unit
directly below the transmission box.
2. Remove the transmission box drain plug
located on the bottom of the transmission
box on the underside of the unit.
Engine Oil Drain
1. Place an oil catch pan under the unit
directly below the engine crankcase.
2.Remove the engine oill drain plug located
on the left-hand side of the engine.
3. Remove the engine oil dipstick located
on the right-hand side of the engine.
4. Allow the oil to drain completely (15-30
min).
5. Reinstall the drain plug and tighten.
Torque to 7-101bf-ft
6. Fill the crankcase with of SAE15W/40
engine oil through the dip dipstick hole.
0.9 liter/0.9 quart.
7.Reinstall the engine oil dipstick and finger
tighten.
8. Dispose of used oil at a proper recycling
station as required by law
3. Remove the transmission box fill whole
plug locate on top of the transmission
4. Allow the oil to drain completely (15-30
min).
5. Reinstall the drain plug and tighten. Torque
to 7-10lbf-ft
6. Fill the transmission box with SAE 80-90
gear oil.
The transmission box capacity is 300cc /
10.2oz.
7. Reinstall the fill hole plug finger tight.
8. Dispose of used oil at a proper recycling
station as required by law.
Copyright ©2008-2009 ETON America,
Pageall
22 rights reserved.
Spark Plug
Replace spark plug at the beginning of each
season with a replacement plug CR7HSA /
NGK.
Disconnect spark plug wire.
Clean dirt from around spark plug base
with brush or air.
Remove spark plug with spark plug wrench.
Set the spark plug gap on the new plug to
0.023" Install the new plug screwing it in
finger tight and then use the plug wrench
to screw the plug in Another 1/2 turn.
Inspect the spark plug wire for cuts, nicks
or other damage. replace as needed.
Spark Arrestor Screen
Required maintenance and cleanout:
1. After every 100 hours of operation the
muffler should be cleaned by removing
the clean out bolt by using a 10mm
wrench.
2. After every 60 hours of operation the
Spark Arrester has to be cleaned by
loosening the retaining nut using a 10
mm socket. Using pliers turn the sleeve
of the Spark Arrester counterclockwise
and pull out. Clean the screen with an
exhaust cleaning solution and replace,
securing it by tightening the retaining nut.
3. After every 200 hours of operation the
Spark Arrester has to be replaced by
loosening the retaining nut using a 10
mm socket. Using pliers turn the sleeve
of the Spark Arrester counterclockwise
and pull out.
Replace a new Spark Arrester and secure
it by tightening the retaining nut.
Copyright ©2008-2009 ETON America,
Pageall
23 rights reserved.
Maintenance Schedule
INITIAL
SERVICE
REGULAR SERVICE EVERY
NOTES
(Every 30
YEAR
operating days)
(First week)
Fuel Line
Throttle Operation
Air Filter system & Element
I
Spark Plug
I
I
I
Fuel Filter
I
Carburetor Idle Speed
Drive Chain
Brake Shoe Wear
Brake System
Brake Fluid
Nut, Bolt, Fastener
Wheels & Wheel Nuts
Steering System
Suspension System
I
I, L
I
I
I
I
I
C.V.T. Air Filter
C.V.T. Drive belt
I
C
I
R
R
R
I
I
I, L
I
I
I
I
I
I
I
C
I
I
R
I
I
Choke
Spark Arrester
Battery
Waste Gas Recovery Valve
C
I,C
R
I
R
I
Intake & Exhaust Valve Adj.
Gear Oil
R every 20 Hours
Engine Oil
OR
R
R every 500 Km
I = Inspect, Clean, Adjust, Lubricate or Replace as needed
C= Clean
L = Lubricate
R = Replace
NOTE: E-TON recommends that all maintenance and inspections be
performed ONLY by a qualified and fully trained technician!
Owners Maintenance Records
Maintenance Preformed
Date
Copyright ©2008-2009 ETON America,
Pageall
24 rights reserved.
Preformed By
OPERATION
Vehicle Break-In procedures
Your vehicle requires a break-In period just
as with all other internal combustion engines.
This period allows the engine parts to seat
and wear properly without undue strain which
can cause premature failure.
1. For the first two weeks of operation
do not run your extended periods of
time.
2. Do not operate the unit at more than
85% of maximum speed.
3. Do not over rev the engine.
4. Use light braking pressure to allow
the brake pads to seat to the rotor
and drums.
Pre-Operation Inspection
Procedures
The following procedure must be
performed before each operating session.
Checking your vehicle takes only a few
minutes and may save you from serious
injuries and costly repairs.
1. Check engine oil level.
2. Check engine fuel level.
3. Check brake operations and brake fluid
level.
4. Check tire condition and pressure.
5. Check drive chain condition and slack.
6. Check throttle operation and free play
adjustment.
7. Check engine stop switch for proper
operation.
8. Check steering system. Look for free
and smooth operation.
Check all fastening hardware.
9. Check all nuts, bolts and other fasteners
for loose conditions.
11. Check all indictor lights and switches
for proper operation.
12. Insure you are wearing proper clothing
and protective gear. Helmet, Gloves
pads etc.
Starting Procedures
The following procedure must be
followed each time you start your unit.
Park the unit on a level surface. Turn the
fuel valve to the "ON" position. Place the
transmission gear selector switch in The
"N", Neutral, position.
Insert the key into the ignition switch and
turn to the "ON" position. Set the manual
choke knob to the full up position (Choke
close or on)
Push the foot brake pedal and turn the
parking Brake lever to "OFF" position. (
Choke off or on) turn the key to the "START"
position,in order to start your unit.
Your unit should start within 10 seconds of
turn the key. If the unit fails to start check
the following.
1. Push the foot brake pedal.
2. Transmission selector switch in the "N"
position
3. Set the manual choke lever to the full
left position (Choke close or on)
10. Inspect unit for any broken or damaged
parts.
Copyright ©2008-2009 ETON America,
Pageall
25 rights reserved.
RIDING TIPS
Driving your vehicle
Parking your vehicle
Your vehicle should only be driven in an
area that is designated for this use. Insure
that the area is free of obstacles and other
dangers that could cause a loss of control.
Check with your local authorities for any
regulations regarding the use of your vehicle.
1. Always park your vehicle on a level
s urface.
2. Turn the ignition key to the "OFF" position to stop the engine.
3. Engage the parking brake locking button.
4. Turn the fuel valve to the "OFF" position.
5. Remove the ignition key to prevent
unauthorized use or theft of your vehicle.
Always keep your feet on the footrests and
your hands on the steering wheel while
operating your vehicle. Doing so will give
you the best control of the unit.
Start your vehicle by following the starting
procedure above and allow the engine a
few minutes to warm up before releasing
the parking brake.
Start the unit by slowly increasing the throttle
until the unit begins moving.
Turning your vehicle
Learning to turn your vehicle requires you
to learn to shift your weight and control the
throttle to allow the rear wheels to turn
properly. When making a turn, the wheels
on the outside of the turn must travel a wider
radius and thus a greater distance than the
inside wheels of the turn. Since the rear
axle does not permit a different rate of
rotation, it is not enough to merely steer
Your vehicle into the turn.
To turn properly, steer in the direction of
the turn and lean your body to the inside
of the turn while supporting your weight on
the outer footrest. supporting your weight
on the outer footrest. Use the throttle to
maintain power through out the turn.
If you do not use this turning technique the
unit will have a tendency to continue in a
straight line. If this occurs, release the
throttle lever to allow the unit to stop. Avoid
braking or accelerating until you have
regained directional control.
Copyright ©2008-2009 ETON America,
Pageall
26 rights reserved.
ROVER
Page 27
Copyright ©2008-2009 ETON America, all rights reserved.
WIRING DIAGRAM
ROVER
GT
Page 28
Copyright ©2008-2009 ETON America, all rights reserved.
WIRING DIAGRAM
ETON AMERICA, LLC.
LIMITED VEHICLE WARRANTY
ETON America warrants all new ETON vehicles sold by authorized ETON Dealers to
be free from defects in materials and workmanship, subject to the following exclusions
and limitations. New vehicles sold by an authorized dealer to original retail consumers
are covered by this policy for a period of six (6) months from the date of delivery. There
is no mileage limitation. This warranty is given to the original retail purchaser and is
non-transferrable.
Vehicles used in rental service or for certain commercial purposes are specifically
excluded from this policy. (Check with your dealer for warranty application.)
Items and conditions that are specifically excluded from this warranty program are;
1.Damage caused by accidents, misuse, negligence, improper vehicle operation,
2.Any modification or alteration to any standard specifications or equipment.
3.Any repairs made by an unauthorized dealer or service firm,
4.Use of non-ETON genuine parts for repairs or alteration to standard specifications.
5.Damage caused by failure to perform factory scheduled service-maintenance.
6.Damage which occurs as a result of improper storage.
7.Damage caused by the use of improper fuel or lubricants, and/or failure to use proper
oil/gas mixture on two stroke models.
The following normal wear parts are specifically excluded from warranty coverage:
1.Rubber parts
2.Tires
3.Belts
4.Brake linings (after 30 days)
5.Normal wear item
6.Brake parts
7.Cables
8.Filters
9.Spark plugs
10.Bulbs
11.Batteries (after 30 days)
12.Sprockets
13.External springs
14.Seat and hand grips.
Scheduled maintenance service is the responsibility of the owner during and after the
warranty period. In the event of a failure or required repair, the owner should take vehicle
to an authorized dealer for repair without undue delay and within a maximum of thirty,
(30), days of the occurrence of the problem. All eligible warranty repairs must be made
at any authorized dealer's normal place of business. Any transportation costs, or other
expenses which may occur in order to obtain warranty service, are the responsibility
of the owner. All eligible repairs covered under this warranty will be paid to the servicing
dealer only, by ETON America, and no additional payments shall be made for authorized
warranty repairs.
Dealer and/or ETON America are not responsible for loss of use, other damage or
inconvenience due to warranty repairs. It is the customer/buyer's responsibility to review
with the selling dealer the pre-delivery service schedule to assure machine is properly
serviced prior to delivery acceptance. It is recommended that the buyer take a test ride
to familiarize themselves with the machine and to make certain the unit is in proper
operating condition. The dealer is responsible for checking and performing all items
on the "set-up and pre-delivery checklist" prior to delivery to the customer.
ETON America, LLC. 7092 Howard Street, Unit F, Spartanburg, SC 29303
Copyright ©2008-2009 ETON America,
Pageall
29 rights reserved.
ETON AMERICA, LLC.
LIMITED VEHICLE WARRANTY
This warranty is valid at any authorized ETON Dealer in the United States only. In the
event you experience any problem obtaining prompt service, contact ETON America,
customer service department for assistance. Always consult first with your selling
dealer and or service personnel for assistance with any service work or repairs. In the
event you have a problem obtaining service send your name, address, and vehicle
identification number to Eton America for assistance.
The above stated policy is the only policy offered and backed by ETON America, and
no other organization or individual is authorized to make or offer any different arrangements. Some states prohibit certain limitations or conditions or do not allow exclusions
or limitations. You may be eligible for additional consideration, so check with your local
dealer or appropriate state agency for assistance. Rights vary from state to state, and
you may have other rights not offered in this warranty.
ETON America warrants all new vehicles comply with applicable US regulations.
LIMITATIONS. This Limited Vehicle Warranty shall not cover any of the following:
Repairs or replacement required as a result of (i) accident, (ii) misuse or neglect, (iii) lack
of reasonable and proper maintenance, (iv) repairs improperly performed or replacement
improperly installed, (v) use of replacement parts or accessories not conforming to ETON
America LLC specifications which adversely affect
1)performance and/or durability, (vi) alterations or modifications not recommended or approved
in writing by ETON America LLC, and/or (vii) use in competitive racing or related events.
2)Replacement of parts and other services and adjustments required for routine maintenance.
3)Any vehicle on which odometer mileage has been changed so that the actual mileage cannot
be determined.
LIMITED LIABILITY.
The liability of ETON America LLC under this Limited Vehicle Warranty is limited solely to
the remedying of the defects in the materials or workmanship by any authorized ETON America
LLC vehicle dealer at its place of business during customary business hours.
Please refer to ETON America LLC website:www.etonamerica.com.
This warranty does not cover inconvenience or loss of use of the Scooter/moped vehicle, or
transportation of the Scooter/moped vehicle to or from the ETON America LLC authorized dealer.
ETON America LLC SHALL NOT BE LIABLE FOR AANY OTHER EXPENSE, LOSS OR
DAMMAGE, WHETHER DIRECT, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY
ARRISING IN CONNECTION WITH THE SALE OR USE OF OR INABILITY TO USE
THE ETON America LLC SCOOTER/MOPED VEHICLE FOR ANY PURPOSE, SOME
STATES DO NOT ALLOW THE EXCLUTION OR LIMITATION OF ANY INCEDENTAL
OR CONSEQUENTAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU.
ETON America, LLC. 7092 Howard Street, Unit F, Spartanburg, SC 29303
Copyright ©2008-2009 ETON America,
Pageall
30 rights reserved.
ETON AMERICA, LLC.
ATV LIMITED WARRANTY
FEDERAL EMMISSION CONTROL SYSTEMS
ETON America LLC warrants each new Scooter/moped vehicle that includes as standard
equipment a taillight and a stoplight;
a) Is designed, built and equipped so as to conform at the time of initial retail purchase with
all applicable regulation of the United States Environmental Protection Agency ("US EPA")
and:
b) Is free from defects in material and workmanship which would cause such Scooter/moped
vehicle to fail to conform with applicable regulations of the US EPA, for a time period of
two and a half (2.5) years and, depending on the engine displacement:
This warranty period shall begin on the date the Scooter/moped vehicle is delivered to the
initial retail purchaser, or on the date the Scooter/moped vehicle is placed in service as
demonstrator, rental, lease, or company Scooter/moped vehicle prior to retail sale.
1) COVERAGE. Warranty defects shall be remedied during customary business hours at any
authorized ETON America LLC Scooter/moped dealer located within the United States in
compliance with the Clean Air Act and applicable regulation of the US EPA. Any part or
parts replaced under this warranty shall become the property of ETON America LLC.
2) OWNERS OBLIGATION. The following obligations must be fulfilled by the owner to
maintain the validity of the ETON America LLC Emission Control System Warranty:
a) Owner must deliver the Scooter/moped vehicle to an authorized ETON America LLC
Scooter/moped vehicle dealer or equally qualified service facility for inspection, maintenance
service and adjustments according to the Periodic maintenance chart provided as part of, or
supplemental to the Owner's manual. Optionally, the Owner may perform this maintenance
only if it is within the scope o f the Owner's technical and practical ability, keeping in mind
some maintenance operations may require special tools or technical expertise beyond the
scope of the average Owner. In any event, the inspection, maintenance and adjustments are
to be performed at the Owner's expense.
b) Owner must present a copy of the proof of initial retail purchase date, issued at the time
of purchase to an authorized ETON America LLC Scooter/moped vehicle dealer at the time
warranty repairs are performed on the Scooter/moped vehicle. You may also be required to
show that you have performed the required maintenance which is related to the alleged defect,
so you should have detail receipts indicating that the required periodic maintenance has been
performed in accordance with the periodic maintenance chart in your Owner's manual.
3) LIMITATIONS. This Emission Control System Warranty shall not cover any of the following:
a) Repairs or replacement required as a result of (i) accident, (ii) misuse or neglect, (iii) lack
of reasonable and proper maintenance, (iv) repairs improperly performed or replacement
improperly installed, (v) use of replacement parts or accessories not conforming to
ETON America, LLC. 7092 Howard Street, Unit F, Spartanburg, SC 29303
Copyright ©2008-2009 ETON America,
Pageall
31 rights reserved.
ETON AMERICA, LLC.
ATV LIMITED WARRANTY
FEDERAL EMMISSION CONTROL SYSTEMS
ETON America LLC specifications which adversely affect performance and/or durability, (vi)
alterations or modifications not recommended or approved in writing by ETON America LLC,
and/or (vii) use in competitive racing or related events.
b) Replacement of parts and other services and adjustments required for routine maintenance.
c) Any Scooter/moped vehicle on which odometer mileage has been changed so that the actual
mileage cannot be determined.
4) LIMITED LIABILITY.
a) The liability of ETON America LLC under this Emission Control System Warranty is limited
solely to the remedying of the defects in the materials or workmanship by any authorized
ETON America LLC Scooter/moped vehicle dealer at its place of business during customary
business hours. Please refer to ETON America LLC website: www.etonamerica.com.
This warranty does not cover inconvenience or loss of use of the Scooter/moped vehicle, or
transportation of the Scooter/moped vehicle to or from the ETON America LLC authorized
dealer.
ETON America LLC SHALL NOT BE LIABLE FOR AANY OTHER EXPENSE, LOSS OR
DAMMAGE, WHETHER DIRECT, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY
ARRISING IN CONNECTION WITH THE SALE OR USE OF OR INABILITY TO USE THE
ETON America LLC SCOOTER/MOPED VEHICLE FOR ANY PURPOSE, SOME STATES
DO NOT ALLOW THE EXCLUTION OR LIMITATION OF ANY INCEDENTAL OR
CONSEQUENTAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. ETON America LLC.
ETON America, LLC. 7092 Howard Street, Unit F, Spartanburg, SC 29303
Copyright ©2008-2009 ETON America,
Pageall
32 rights reserved.
Copyright ©2008-2009 ETON America,
Pageall
33 rights reserved.
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-MFG:
TON No
E-TON
E-TON E-TON E-TON E-TON E-TON
498, Section 2, Bentian Road, Tainan, 709,
E-Taiwan,
TON ER.O.C.
-TON E-TON E-TON E-TON E-TON E-TON
E-Tel:
TON+886-6-3840568
E-TON E-TON E-TON E-TON E-TON E-TON
Fax: 886-6-3840968
E-http:///www.e-ton.com.tw
TON E-TON E-TON E-TON E-TON E-TON E-TON
E-mail: sales@e-ton.com.tw
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON E-TON E-TON
E-TON E-TON E-TON E-TON E-TON EH9900-9UB0-0000
-TON E-TON
E-TON
E-TON E-Copyright
TON ©2008-2009
E-TONETONEAmerica,
-TONall rights
E-reserved.
TON E-TON E-TON