DeView LCD Monitor Instruction manual

10.4” Dual Rack Mount
TFT-LCD Monitor
INSTRUCTION MANUAL
Please read this manual thoroughly before use.
Keep it handy for future reference.
Document Number: V531-LD100-000
Ver. 07/2010
* * * WARNING * * *
This equipment has been tested and found to comply with the
Class A digital device‚ pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and uses in
accordance with the instruction manual, may cause harmful
interference to radio communication. Operation of this equipment in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at its own
expense.
Notice: The change or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equivalent.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS.
CAUTION:
CAUTION
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of un-insulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
2
Precautions

Safety

Should any liquid or solid object fall into
the cabinet, unplug the unit and have it
checked by the qualified personnel before
operating it further.
Installation
Do not install the unit in an extremely hot
or humid place or in a place subject to
excessive dust or mechanical vibration.
The unit is not designed to be waterproof.
Exposure to rain or water may damage
the unit.
Unplug the unit from the wall outlet if it is
not going to be used for several days or
more. To disconnect the cord, pull it out by
the plug. Never pull the cord itself.

Cleaning
Clean the unit with a slightly damp soft
cloth.
Use a mild household detergent. Never
use strong solvents such as thinner or
benzene as they might damage the finish
of the unit.
Allow adequate air circulation to prevent
internal heat build-up. Do not place the
unit on surfaces (rugs, blankets, etc.) or
near materials(curtains, draperies) that
may block the ventilation holes.
Retain the original carton and packing
materials for safe transport of this unit in
the future.
3
FCC COMPLIANCE STATEMENT
INFORMATION TO THE USER: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO
COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE, PURSUANT TO PART 15
OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE
PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL
INSTALLATION.
THIS EQUIPMENT GENERATES, USES AND CAN RADIATE RADIO FREQUENCY
ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE
INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO
COMMUNICATIONS. HOWEVER, THERE IS NO GUARANTEE THAT INTERFERENCE
WILL NOT OCCUR IN A PARTICULAR INSTALLATION. IF THIS EQUIPMENT DOES
CAUSE HARMFUL INTERFERENCE TO RADIO OR TELEVISION RECEPTION,
THIS CAN BE DETERMINED BY TURNING THE EQUIPMENT OFF AND ON, THE USER
IS ENCOURAGED TO TRY TO CORRECT THE INTERFERENCE BY ONE ON MORE OF
THE FOLLOWING MEASURES:
-RE-ORIENTATE OR RELOCATE THE RECEIVING ANTENNA
-INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND RECEIVER.
-CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM
THAT TO WHICH THE RECEIVER IS CONNECTED.
-CONSULT THE DEALER OR AN EXPERIENCED RADIO/TV TECHNICIAN FOR HELP
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE
PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER'S AUTHORITY TO
OPERATE THE EQUIPMENT.
THIS PRODUCT CPMPLIES WITH CARIOUS OTHER REGIONAL AND SAFETY
REGULATIONS SUCH: FCC, CE.
THESE CERTIFICATIONS ARE NOTED ON THE PRODUCT LABEL.
4
Important Safeguards
1. READ INSTRUCTIONS -- All the
safety and operating instructions
should be read before the appliance is
operated.
8. POWER SOURCES – The Video
monitor or equipment should be
operated only from the type of power
source indicated on the marking label.
If you are not sure of the type of power
supplied to your home, consult your
video monitor or equipment dealer or
local power company. For video
monitor or equipment designed to
operate from battery power refer to
the operating instructions.
2. RETAIN INSTRUCTIONS -- The
safety and operating instructions
should be retained for future
reference.
3. CLEANING -- Unplug video monitor or
equipment from the wall outlet before
cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth
for cleaning.
9. GROUNDING OR POLARIZATION -This video monitor power supply may
be equipped with a polarized
alternating - current line plug (a plug
having one blade wider than the
other). This plug will fit into the power
outlet only one way. This is a safety
feature. If you are unable to insert the
plug fully into the outlet, try reversing
the plug. If the plug should still fail to
fit, contact your electrician to replace
your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
4. ATTACHMENTS -- Do not use
attachments not recommended by the
video monitor or equipment
manufacturer as they may result in the
risk of fire, electric shock or injury to
persons.
5. WATER AND MOISTURE -- Do not
use video monitor or equipment near
water -- for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in
a wet basement, or near a swimming
pool, or the like.
Alternate Warnings - This video
monitor’s power supply is equipped
with a three-wire grounding-type plug,
a plug having a third (grounding) pin.
This plug will only fit into a
grounding-type power outlet. This is a
safety feature. If you are unable to
insert the plug into the outlet, contact
your electrician to replace your
obsolete outlet. Do not defeat the
safety purpose of the grounding-type
plug.
6. ACCESSORIES -- Do not place video
monitor or equipment on an unstable
cart, stand or table. The video monitor
or equipment may fall, causing
serious injury to a child or adult, and
serious damage to the equipment.
Wall or shelf mounting should follow
the manufacturer's instructions, and
should use a mounting kit approved
by the manufacturer.
10. POWER CORDS -- Do not allow
anything to rest on the power cord. Do
not locate video monitor or equipment
where the cord will be abused by
persons walking on it.
6.A. The Video monitor or equipment
and cart combinations should be
moved with care. Quick stops,
excessive force, and uneven
surfaces may cause the equipment
and cart combination to overturn.
11. HEED WARNINGS -- Follow all
instructions marked on the video
monitor or equipment.
7. VENTILATION -- Slots and openings
in the cabinet and the back or bottom
are provided for ventilation, and to
ensure reliable operation of the video
monitor or equipment and to protect it
from overheating. These openings
must not be blocked or covered. The
openings should never be blocked by
placing the video monitor or
equipment on a bed, sofa, rug, or
other similar surface. The Video
monitor or equipment should never be
placed near or over a radiator or heat
source. The Video monitor should not
be placed in a built-in installation such
as a bookcase unless proper
ventilation is provided.
12. LIGHTNING -- For added protection
for video monitor or equipment during
a lightning storm, or when it is left
unattended and unused for long
periods of time, unplug it from the wall
outlet and disconnect the antenna or
cable system. This will prevent
damage to the video product due to
lightning and power-line surges.
13. OVERLOADING --Do not overload
wall outlets and extension cords as
this can result in a risk of fire or
electric shock.
5
Important Safeguards
14. OBJECT AND LIQUID ENTRY -Never push objects of any kind into
video monitor or equipment through
openings as they may touch
dangerous voltage points or short-out
parts that could result in a fire or
electric shock. Never spill liquid of any
kind on the product.
17. SAFETY CHECK -- Upon completion
of any service or repairs to this video
product, ask the service technician to
perform safety checks to determine
that the video product is in proper
operating condition.
18. FIELD INSTALLATION -- This
installation should be made by a
qualified service person and should
conform to all local codes.
15. SERVICING -- Do not attempt to
service video monitor or equipment
yourself as opening or removing
covers may expose you to dangerous
voltage or other hazards. Refer all
servicing to qualified service
personnel.
16. DAMAGE REQUIRING SERVICE -Unplug video monitor or equipment
from the wall outlet and refer servicing
to qualified service personnel under
the following conditions:
A.
When the power-supply cord or
the plug has been damaged.
B.
If liquid has spilled, or objects
have fallen into the video
product.
C.
If the video product has been
exposed to rain or water.
D.
If the video product does not
operate normally by following the
operating instructions, adjust
only those controls that are
covered by the operating
instructions as an improper
adjustment of other controls may
result in damage and will often
require extensive work by a
qualified technician to restore the
video product to its normal
operation.
E.
If the video product has been
dropped, or the cabinet
damaged.
F.
When the video product exhibits
a distinct change in performance
-- this indicates a need for
service.
6
Installation Guide
Accessory
All of the accessories have been tested and qualified.
Do not use any non-qualified accessories with this LCD monitor.
Please check all accessories before installation LCD monitor.
For USA:
 AC power cord x 1
 10.4” LCD monitor x 2
For EU and UK:
 European AC power cord x 1
 AC Adaptor x 1
 UK AC power cord x 1
 User manual x 1
Instruction Read Guide
Forbid label:
Warning that failure to observe
could result in damage while
operating or installing the
monitor incorrectly.
Danger label:
To draw installer’s attention that if
caution is not observed potential
injury to the installer or other
persons could occur.
Attention label:
The user should pay attention to
the explanation in the manual for
this item while configuring the
monitor.
Doubt label:
A warning that the installer’s may
need to consult with others for
more details on option before
proceeding.
Suggestion label:
The user may like to consider this
for an optimal setting.
7
Contents
……………………………………………………2
……………………………………………………3
FCC Compliance Statement
……………………………………4
Important Safeguards
…………………………………………5
Installation Guide ………………………………………………7
Contents ……………………………………………………8
Quick installation ………………………………………………9
Features ……………………………………………………10
Resolution Support
…………………………………………11
Operating Instructions Controls
……………………………………12
Backside Connections
…………………………………………13
OSD Architecture ………………………………………………14
A. OSD Tree CVBS ..……………………………………………14
B. OSD Tree VGA
…………………………………………15
C. CVBS Setup ………………………………………………16
D. VGA Setup
………………………………………………17
E. General Setup ………………………………………………20
Mounting Guide
………………………………………………21
Typical Device Connections ………………………………………22
Dimensions
………………………………………………23
Specification
………………………………………………24
Appendixes
………………………………………………25
Memo
……………………………………………………27
 Warning
 Precaution
















-8-
Quick Installation when using with a PC
For instructions on rack mounting, see page 18 of this user guide.
1
Connect power cord
2
Connect video cable
• Make sure both the LCD display and computer are turned OFF
• Connect the video cable from the LCD display to the computer.
3
Turn ON LCD display and computer
• Turn ON the LCD display, then turn ON the computer. This sequence (LCD
display before computer) is important.
4
Windows users: Set the timing mode (resolution and refresh rate)
Example: 800 x 600 @ 60 Hz.
For instructions on changing the resolution and refresh rate, see the graphic
card’s user guide
Installation is complete. Enjoy your new LCD display.
-9-
Features










General
10.4” (800 x RGB x 600) TFT LCD Panel.
Advanced control OSD menu.
Brightness of 220 cd/m²
High contrast of 400 : 1
PC

1 analog RGB signal input.
Compatible with SVGA (800 x 600) resolution.
Support vertical refresh rate up to 75 Hz for VESA standard specification.
Automatic or manual optimum detection of separate sync and
composite sync of VGA signal.
VGA screen horizontal / vertical position and width adjustment.

VIDEO





2 composite (CVBS) signal input.
2 composite (CVBS) signal loop-out.
Video loop-out support auto termination (75 Ohms).
Video input support NTSC / PAL standard.
Color temperatures: Weak / Strong / User Selectable

Other





Power-on default selections.
Easily selectable video switching function.
Provide multi language (English, French, German, Italian, Spanish,
Simplified Chinese and Japanese).
Rack mount design.
Power consumption 18W @ DC12V
- 10 -
Resolution Support

VGA resolution table
Resolution
Symbol
H Freq.
V Freq.
Pixel
Remark
640 x 480
640-60
31.469
59.941
25.175
VESA
640 x 480
640-72
37.861
72.810
31.500
VESA
640 x 480
640-75
37.500
75.000
31.500
VESA
800 x 600
800-56
35.156
56.250
36.000
VESA
800 x 600
800-60
37.879
60.317
40.000
VESA
800 x 600
800-72
48.077
72.188
50.000
VESA
800 x 600
800-75
46.875
75.000
49.500
VESA
Please note, selecting frequencies outside these ranges may result in an
abnormal image or damage to the monitor.
- 11 -
Operating Instructions Control
Power
Monitor ON / OFF. At OFF mode, monitor will be in standby status.
Light indicates:
Green – Power On
Red – Standby mode.
No light – Power Off
MENU/ENTER (Menu Select)
Press to enter OSD menu.
When OSD menu is active, press to access the items in the menu.
As the adjustment complete, press again to confirm the adjustment then
move downward to the next selection.
Adjust UP (Input Source/ Value Adjust Key)
When OSD menu is non-active, select the next input from CVBS1,
CVBS2, and VGA.
When OSD menu is active, select the item above or increment the
current value.
Adjust Down (Input Source/ Value Adjust)
When OSD menu is non-active, select the previous input from CVBS1,
CVBS2, and VGA.
When OSD menu is active, select the item below or decrement the
current value.
- 12 -
Backside Connections
1 DC POWER IN: DC12V power input.
○
2 RIGHT MONITOR CVBS2 IN: composite video signal input for
○
CVBS2 channel.
3 RIGHT MONITOR CVBS2 OUT: Video auto termination loop-out for
○
CVBS2 IN signal. Auto termination impedances are 75 Ohms.
4 RIGHT MONITOR CVBS1 IN: composite video signal input for
○
CVBS1 channel.
5 RIGHT MONITOR CVBS1 OUT: Video auto termination loop-out for
○
CVBS1 IN signal. Auto termination impedances are 75 Ohms.
6 RIGHT MONITOR VGA IN: Analog RGB signal input for VGA.
○
7 LEFT MONITOR CVBS2 IN: composite video signal input for CVBS2
○
channel.
8 LEFT MONITOR CVBS2 OUT: Video auto termination loop-out for
○
CVBS2 IN signal. Auto termination impedances are 75 Ohms.
9 LEFT MONITOR CVBS1 IN: composite video signal input for CVBS1
○
channel.
10 LEFT MONITOR CVBS1 OUT: Video auto termination loop-out for
○
CVBS1 IN signal. Auto termination impedances are 75 Ohms.
11 LEFT MONITOR VGA IN: Analog RGB signal input for VGA.
○
- 13 -
OSD Architecture
OSD Menu Tree CVBS
- 14 -
OSD Architecture
OSD Menu Tree VGA
- 15 -
OSD Architecture
CVBS Setup (Picture)
Brightness
50
Contrast
50
Saturation
60
50
Hue
Sharpness
0
Back Light
[ Strong ]
▼▲
Exit OSD
Picture
CVBS1
Press Enter Key and the OSD MENU pop up.
Press Arrow Down or Arrow Up Key to move cursor to
then press Enter to
access the CVBS Setup.
Move Arrow Down and Arrow Up Key to adjust the values of each selection.
Press Enter key to confirm the change and move to the next selection.
Press Enter key to “Exit OSD” and press Arrow Down or Arrow Up Key to
Exit the OSD MENU.

Brightness:
Adjust the overall picture shade and brightness.

Contrast:
Permits adjustment for contrast between light or dark areas of the
picture.

Saturation:
Adds coloring to the black and white picture content (of a color
signal), and is usually set for viewer’s preference in color
saturation.

HUE:
Adjusts all the colors on the screen, but is most noticeable to the
eye in reds and yellows, and is also usually set for pleasing face
tones (NTSC only).

Sharpness:
Sets the desired sharpening enhancement to the picture.

Backlight:
This feature is designate to directly adjust the backlight levels of
LCD panel in case the unnecessary light condition should hinder
the viewing of the images. Press Arrow Down or Arrow Up Key to
adjust.
(i.e. the LCD monitor is installed on a strong-lighted office or
surveillance center). [Strong]or [Weak] selectable.
- 16 -
OSD Architecture
VGA Setup (Picture)
Brightness
50
Contrast
50
Back Light
[ Strong ]
[ Cool ]
Color temp.
▼▲
▼▲
Color Adjust
Exit OSD
Picture
VGA
Press Enter Key and the OSD MENU pop up.
Press Arrow Down or Arrow Up Key to move cursor to
then press Enter to access the VGA Setup.
Move Arrow Down and Arrow Up Key to adjust the values of each selection.
Press Enter key to confirm the change and move to the next selection.
Press Enter key to “Exit OSD” and press Arrow Down or Arrow Up Key to
Exit the OSD MENU.

Brightness:
Adjust the overall picture shade and brightness.

Contrast:
Permits adjustment for contrast between light or dark areas of the
picture.

Backlight:
This feature is designate to directly adjust the backlight levels of
LCD panel in case the unnecessary light condition should hinder
the viewing of the images.
Press Arrow Down or Arrow Up Key to adjust.
(i.e. the LCD monitor is installed on a strong-lighted office or
surveillance center). [Strong]or [Weak] selectable.
- 17 -
OSD Architecture
VGA Setup
Brightness
50
Contrast
50
Back Light
[ Strong ]
[ User ]
Color Temp.
▼▲
▼▲
Color Adjust
Exit OSD
Picture
VGA

Color Temp.: Select color temperature presets of [ Cool ], [ Warm ] ,
or [ User ] for User-Define setting.

Color Adjust: This function is available only when color temperature function is
selected to User-Define setting [ User ].
Press Arrow Down or Arrow Up Key to enter the sub menu.
Move Arrow Down or Arrow Up Key to adjust the values of each
selection.
Press Enter Key to confirm the change and move to the next
selection.
Select Back and press Arrow Down or Arrow Up Key to exit the
sub menu.
Red
128
Green
128
Blue
128
Back
▼▲
User-Define Color Temperature Adjustment
- 18 -
OSD Architecture
VGA Setup
Auto Adjust
▼▲
H. Position
50
V. Position
50
50
Clock
Phase
71
▼▲
Exit OSD
Picture
VGA
Press Enter Key and the OSD MENU pop up.
Press Arrow Down or Arrow Up Key to move cursor to
then press Enter to access the VGA Setup.
Move Arrow Down and Arrow Up Key to adjust the values of each selection.
Press Enter key to confirm the change and move to the next selection.
Press Enter key to “Exit OSD” and press Arrow Down or Arrow Up Key to Exit the OSD
MENU.

Auto Adjust:
This feature allows the user to auto-optimize the displayed picture
under VGA mode.
Press Arrow Down or Arrow Up Key to activate this function

H. Position:
Adjust horizontal position of image.

V. Position:
Adjust vertical position of image.

Clock:
Allow adjustment for P-CLOCK timer.

Phase:
Allow adjustment for P-CLOCK phase.
- 19 -
OSD Architecture
General Setup
Power On Default
[ CVBS 1 ]
Language
[ English ]
10
OSD Timeout
▼▲
▼▲
Reset
Exit OSD
Setup
CVBS1
Press Enter Key and the OSD MENU pop up.
Press Arrow Down or Arrow Up Key to move cursor to
then press Enter to access the General Setup.
Move Arrow Down or Arrow Up Key to adjust the values of each selection.
Press Enter key to confirm the change and move to the next selection.
Press Enter key to “Exit OSD” and press Arrow Down or Arrow Up Key to
Exit the OSD MENU.



Power On Default: Set the signal input priority at power ON.
CVBS1:
Set channel to CVBS1 when power is turned ON.
CVBS2:
Set channel to CVBS2 when power is turned ON.
VGA:
Set channel to VGA when power is turned ON.
OFF:
Disable the signal input priority function.
Language:
Allow user to select the OSD menu Languages.
Select from English, German, French, Spanish, Italian, Simplified
Chinese or Japanese.
OSD Timeout: Set the OSD display time from [5] to [60] seconds.

Reset:
Reset the monitor to the original factory settings.
Press Arrow Down or Arrow Up Key to activate the reset function.

Exit OSD:
Exit OSD Menu.
Press Arrow Down or Arrow Up Key to exit OSD menu.
- 20 -
Mounting Guide
Rack Mounting
1
Line up the 3 mounting guides
on each side of the monitor with
appropriate holes in the rack
2
Insert and slightly tighten rack mounting
screws on the upper mounting guides on
each side
3
Place the monitor into the rack and be
hooked
on the installed rack mounting screws
(use the larger holes on both sides of the
bracket).
Tighten two mounting screws on each
bracket.
4
Insert and tighten the rest rack mounting screws.
Use screws applicable to the rack system in use.
Failure to observe this may result in serious injury.
If there is any doubt of the suitability of a mount or
fixing method, a suitably qualified technician should
be consulted.
- 21 -
Typical Device Connections
- 22 -
Dimensions
- 23 -
Specification
LCD Size
Pixel Type
Max. Resolution
Aspect Ratio
10.4"
Normal white
800 x RGB x 600
4:3
640 x 480 @ 60/72/75
800 x 600 @ 56/60/72/75
Resolution / Scan for VGA
Viewing Area
Pixel Pitch
Brightness
Contrast Ratio
Type
Hours
Backlight Type
Viewing Angle (H/V)
Display Color
Response Time
Sync. Format
Frequency (Horizontal)
Frequency (Vertical)
Input
Interfaces
Video Interface
VGA
(H) x (V)
0.264 x 0.264 mm
220 cd/m2
400:1
1CCFL
20,000 hr(Typ)
110/80
262K colors
40ms(tr+tf)
NTSC / PAL
PC: 31.5K~46KHz Video 15750 / 15625Hz (NTSC/PAL)
PC: 56Hz~75Hz Video: 50 / 60Hz
D-Sub 15 In x 1, Video In x 2 (BNC), Video Out x 2 (BNC)
Yes, x 1
CVBS
Yes, x 2
Input Power
Input Signal
Front Panel Controls
Indicators
TBS
CTI
AGC
Special
Color Temperature
Features
Rack mount Type
DC JACK x 1
Composite signal 0.5~2Vpp / 75ohm (Auto Termination)
Power, Adjust Up/Down, Menu
LED, Power on, Stand by
Yes
Yes
Yes
Cool / Warm / User Selectable
Yes
English, French, German, Italian, Spanish,
Simplified Chinese, Japanese
VESA 100
DC12V @ 5amps
0 ゚ C ~ 40 ゚ C
-10 ゚ C ~ 60 ゚ C
Language
VESA Mounting
Power Type
Temp (Oper.)
Temp (Storage)
- 24 -
Appendixes
Check the information in this section to see if the problems can be solved before requesting
repair:
The consumers are only allowed to solve the problems described as below.
Any unauthorized product modification, or failure to follow instructions supplied with the
product will void the warranty immediately.
Problem: No Power indicates

Make sure power cord is correct.

Make sure the voltage output is correct. DC12V at 5amps.
Problem: No image


Make sure power button is ON.
Check whether the LCD monitor and computer or video devices power cords are
plugged and whether there is a supply of power.
Problem: No signal

Check the signal connection between the computer and LCD monitor.

Make sure the computer power is ON.

Make sure the signal cable is correct.
Problem: “Out of Range”

Check the computer image output resolution and frequency and compare the
value with preset value (please refer to page 11).
Problem: Fuzzy image

Perform “Auto Adjust” in VGA setup or select “Clock” to adjust manually and
acquire a better image (please refer to page 19).
Problem: Image too bright or Image too dark

Adjust brightness and contrast by OSD (please refer to page 16 and 17).
Problem: Irregular image

Check the signal connection between the computer and LCD monitor.

Perform “Auto Adjust” in VGA setup (please refer to page 19).
Problem: Distorted image

Reset LCD monitor.
(perform the “Reset” function by OSD “General Setup”, page 20 )
Problem: Image is not centered on screen

Use OSD menu to adjust H-Position and V-Position.

Perform “Auto Adjust” in VGA Setup (please refer to page 19).
- 25 -
Appendixes
Problem: Uneven color or color too dark

Use OSD “Picture” function to adjust color setting.
(please refer to page 16 for CVBS1/CVBS2 input or page 17 for VGA input).
Problem: White color is not white

Check “Color temp” is correct (for VGA input).

Use OSD “Color Adjust” function to adjust color temperature (page 18).

Use OSD “Hue” function to adjust color setting (for CVBS input, page 16).
Problem: Can not adjust LCD monitor with buttons in the front.

Make sure the LCD Power is ON and the connections are correct.

Turn-off and on then reset the LCD.
If the LCD doesn’t respond as the keys are pressed, please contact the service
representatives for further information.
- 26 -
Memo
- 27 -