Miele DA 5320 D Technical data

Operating and Installation instructions
Rangehood
DA 5320 W
To avoid the risk of accidents
or damage to the appliance,
it is essential to read these
instructions before it is installed
and used for the first time.
en - AU, NZ
M.-Nr. 09 730 370
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Description of the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Miele|home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Con|ctivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To switch the fan on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
To select a power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Run-on option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To switch the fan off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To switch the cooktop lighting on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To dim the cooktop lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To switch the cooktop lighting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Filter operating hours counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Grease filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Changing a halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Safety distance between cooktop and rangehood (S) . . . . . . . . . . . . . . . . . . . 25
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Assembly parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Protective foil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Dismantling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Operation with Control module DSM 400 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Potential free connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Connection to a light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
2
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
or machine
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance or the machine to prevent
misuse.
3
Warning and Safety instructions
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal
injury and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time. They
contain important information on the
safety, installation, use and
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~ This rangehood is designed for
domestic use and for use in similar
environments by guests in hotel or
motel rooms, bed & breakfasts and
other typical living quarters. This does
not include common/shared facilities or
commercial facilities within hotels,
motels or bed & breakfasts.
~ It must only be used to extract
vapours and remove odours from
cooking.
4
~ This appliance is not suitable for
outdoor use.
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
have been given supervision or
instruction concerning its use by a
person responsible for their safety.
~ This appliance may only be used in
mobile installations if a risk assessment
of the installation has been carried out
by a suitably qualified engineer.
Safety with children
~ This appliance is only intended for
use by adults who have read these
instructions.
~ This appliance is not a toy! To avoid
the risk of injury keep children well
away. Children should be supervised to
ensure that they do not play with the
appliance.
~ Please be aware that on
rangehoods with halogen lighting, the
lamps will get very hot during use and
remain hot for some time after switching
off. To safeguard against burning, keep
children well away from the lamps at all
times.
Warning and Safety instructions
Technical safety
~ Before installation, check the
rangehood for visible signs of damage.
Do not install and use a damaged
appliance. A damaged appliance is
dangerous.
~ Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
on-site electricity supply, otherwise the
appliance could be damaged. Consult
a qualified electrician if in doubt.
~ The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly and, where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~ For safety reasons, this appliance
may only be used when it has been
fully installed.
~ Installation, maintenance and
repairs may only be carried out by a
suitably qualified and competent
person in strict accordance with current
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
~ Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~ During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:
– it is switched off at the isolator,
– the screw-out fuse is removed (in
countries where this is applicable),
– the mains fuse is disconnected.
Do not pull the mains connection
cable but the mains plug to
disconnect your appliance from the
mains electricity supply.
~ Only open the casing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the casing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
5
Warning and Safety instructions
~ Do not connect the appliance to the
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~ This rangehood must not be
installed and operated in mobile
installations (e.g. on a ship).
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the warranty.
~ Great care should be taken when
using the rangehood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas cooktops or ovens which draw air
in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, with or
without an external motor fitted, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
6
Warning and Safety instructions
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the extractor
and the heater are in operation
simultaneously, an underpressure in the
room of 0.04 mbar (4 pa) is the
maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the extractor can only
be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder must be
sought.
7
Warning and Safety instructions
Correct use
~ Never use an open flame beneath
the rangehood. To avoid the danger of
fire, do not flambé or grill over an open
flame.
When switched on, the rangehood
could draw flames into the filter. Fat
particles drawn into the rangehood
present a fire hazard.
~ Do not use the rangehood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
~ The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~ When using the rangehood over a
gas cooktop, ensure that any burners in
use are always covered by a pan.
Switch the cooking zone off when a pan
is removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The rangehood can become damaged
when exposed to excessive heat.
~ Do not use a steam-cleaner to clean
~ Always switch the rangehood on
~ The minimum safety distances
when a cooking zone is in use,
otherwise condensation may collect in
the rangehood, which could cause
corrosion.
~ When cooking with oil or fat, chip
pans and deep fat fryers etc, do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the rangehood on fire.
8
this appliance. Pressurised steam
could reach the electrical components
and cause a short circuit.
Correct installation
~ Refer to the rangehood or cooktop
manufacturer's instructions as to
whether a rangehood may be operated
above the cooktop.
between the top of the cooktop and the
bottom of the rangehood given in the
"Appliance dimensions" section of this
booklet must be maintained, unless the
cooktop manufacturer states that a
greater safety distance is required.
~ If more than one cooking appliance
is fitted beneath the rangehood, and
they have different minimum safety
distances to the rangehood, select the
greater distance.
Warning and Safety instructions
~ Safety regulations prohibit the fitting
of a rangehood over solid fuel stoves.
~ All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from Miele or
from builders' merchants.
~ The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~ If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
Accessories
~ Only use genuine Miele spare parts
and accessories with this appliance. If
spare parts or accessories from other
manufacturers are used, this will
invalidate the warranty, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
9
Guide to the appliance
10
Guide to the appliance
a Telescopic extension piece
b Tower
c Canopy
d Grease filters
e Decor panels Miele DDW 53x0
(optional accessory)
4 panels are required for the
DA 5320 W. These ensure optimum
edge extraction of cooking vapours
above an induction or ceramic cooktop.
f Control panel
g Cooktop lighting
h Touch control for the cooktop
lighting
This control switches the lighting on
and off, and is also a dimmer switch.
i On/Off touch control for the fan
j Controls to select fan power level
k Touch control for the run-on
option
To activate the run-on option. The fan
can be set to continue running, and to
switch off automatically after either 5 or
15 minutes.
l Touch control for the
grease filters
The indicator lamp for the grease filters
lights up when the grease filters need
to be cleaned.
The touch control is used to reset the
operating hours counter every time the
grease filters are cleaned (see
"Cleaning and care").
It can also be used to check and alter
the operating hours counter.
For information about using the
appliance, see "Operation".
11
Description of the functions
The rangehood works with
. . . . . . air extraction:
The air is drawn in and cleaned by the
grease filters and directed outside.
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the rangehood
is switched off.
When the rangehood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
Please note, the performance of
this rangehood hinges greatly on
the installed ducting to vent the
vapours. Poor choice of ducting
results in poor rangehood
performance. For ducting
recommendations, please refer to
the relevant section in these
operating instructions or contact
a specialised installer.
12
Miele|home
Con|ctivity
– When the cooktop is switched on,
the cooktop lighting and the
rangehood fan also switch on.
– During cooking the rangehood
automatically sets the fan's power
level according to the number of
cooking zones in operation and their
power levels.
– After switching the cooktop off, the
fan and the cooktop lighting will
switch off automatically after a period
of time.
This rangehood is communication
enabled.
Communication module XKM 2000 DA
a, available as an optional extra,
enables the operation of the rangehood
to be automatically controlled by the
operating status of a Miele electric
cooktop with onset controls.
For communication to take place, the
cooktop must be fitted with
communication module b.
For detailed information about this
function, please read the separate
instruction booklet supplied with the
XKM 2000 DA communication module.
The communication module is fitted to
the rangehood in the area of the fan
and is connected to the controls of the
rangehood.
This module must be installed by a
Miele service technician or suitably
qualified electrician.
The cooktop transmits information
about its operating status to the
rangehood via the household power
supply (Powerline) c.
13
Operation
To switch the fan on
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it only runs for 10 minutes before
reverting automatically to level III.
^ Press the On/Off control.
The fan runs at power level "II".
The indicator lamp will come on.
^ To set this option, both the fan and
the cooktop lighting must be
switched off.
To select a power level
^ Use the – / + controls to select the
power level required.
^ Press the run-on option control for
approximately 10 seconds. The first
fan setting indicator will light up.
^ Then press in turn,
+ control = higher setting
– control = lower setting
Depending on the intensity of cooking
vapours, levels "I" to "III" are usually
sufficient for normal cooking.
– the cooktop lighting control,
Intensive setting
When frying or cooking food with a
strong aroma, you may wish to select
the Intensive setting, level IV for a short
period.
– the – control, and
– the cooktop lighting control again.
14
Operation
Run-on option
The indicator lamps for fan power levels
I and IV will flash if the automatic
switch-off for the Intensive setting is not
activated.
^ Press the + control to activate the
automatic switch-off.
The indicator lamps for fan power
levels I and IV will now light up
constantly.
Press the – control to deactivate the
automatic switch-off function.
It is advisable to leave the fan running
for a few minutes after cooking has
finished to neutralise any lingering
odours in the air.
The fan can be set to switch off
automatically after either 5 or 15
minutes:
^ After cooking has finished, press the
run-on option control whilst the fan is
still running.
– Press once = The fan will switch off
after 5 minutes (left-hand indicator
lamp).
^ Press the run-on option control to
confirm your selection.
If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the original
setting.
– Press twice = The fan will switch off
after 15 minutes (right-hand indicator
lamp).
To switch off the run-on option, press
the run-on option control again. The
appliance will then not switch off
automatically.
To switch the fan off
^ Press the On/Off control to switch the
fan off.
The indicator lamp will go out.
15
Operation
To switch the cooktop lighting
on
The cooktop lighting can be switched
on and off independently of the fan.
^ Briefly press the cooktop lighting
control to switch on the cooktop
lighting.
The indicator lamp will come on.
The lighting will switch on at maximum
brightness.
To dim the cooktop lighting
The brightness of the lighting can be
adjusted.
^ With the lighting switched on, press
and hold the cooktop lighting control
in.
The brightness will gradually dim until
you release the control.
^ Press the control in again to increase
the brightness to the level required,
and then release it.
If you keep the control pressed in, the
light will continually change between
bright and dim.
To switch the cooktop lighting
off
^ Briefly press the cooktop lighting
control to switch the lighting off.
The indicator lamp will go out.
16
Safety cut-out
Should the rangehood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
^ Pressing the On/Off control will
switch the fan back on again.
Operation
Filter operating hours counter
The number of hours the appliance has
been in operation is stored in memory.
The operating hours counter tells you
when the grease filters need to be
cleaned.
Resetting the operating hours
counter for the grease filters
After 30 hours of operation (or another
time if the operating hours counter has
been altered), the grease filter indicator
lamp will light up. The grease filters
must then be cleaned.
Reading the filter operating hours
counter
To check the percentage of time set
already used:
^ Press the On/Off control to switch the
fan on.
^ Press and hold the grease filter
control.
Afterwards, the filter operating hours
counter must be reset.
^ To do this, press and hold the grease
filter control in for approximately
3 seconds while the fan is switched
on.
The indicator lamp for the control will
go out.
One or more of the indicator lamps for
the – / + controls will flash.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
2 lamps
3 lamps
4 lamps
= 25 %
= 50 %
= 75 %
= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
17
Operation
Altering the filter operating hours
counter
The filter operating hours counter is set
at 30 hours. This can be lengthened or
shortened to suit the type of cooking
you do. You can choose 20, 30, 40 or
50 hours
– Select a short time if you roast or fry
a lot.
The – / + indicator lamps show the time
which has been set:
1st lamp from the left = 20 hours
2nd lamp from the left = 30 hours
3rd lamp from the left = 40 hours
4th lamp from the left = 50 hours
– If you use very little fat for cooking,
select a longer time.
^ Use the – / + controls to select the
desired time.
– If you only cook occasionally we
recommend that you still select a
short time, because grease which
has built up gradually over a long
period of time will harden on the
grease filters and make cleaning
more difficult.
^ Press the On/Off control to switch the
fan off.
^ Press the run-on option control and
the grease filter control at the same
time.
The indicator lamp for the grease filter
control and one of the – / + indicator
lamps will flash.
18
^ Confirm the selection by pressing the
grease filter control.
All the indicator lamps will go out.
If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the original
setting.
Cleaning and care
,Before any cleaning or
maintenance work is carried out,
disconnect the rangehood from the
mains supply.
Ensure that:
– it is switched off at the
isolator, or
– it is switched off at the wall
socket and the plug
removed, or
– the mains fuse is withdrawn, or
– the screw-out fuse is removed
(in countries where this is
applicable).
A range of Miele branded cleaning and
conditioning agents are available to
order through your Miele Chartered
Agent, from Miele, or via the internet at
www.miele-shop.com.
Housing
General notes
The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
^ All external surfaces and controls can
be cleaned using the Original Miele
all purpose microfibre cloth or with
warm water and a small amount of
washing-up liquid applied with a well
wrung-out soft sponge or cloth.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents e.g.
powder cleaners or cream cleaners,
and abrasive sponges, e.g. pot
scourers or sponges which have
been previously used with abrasive
cleaning agents. These will damage
the surface material.
Important for appliances with
stainless steel housing
(This infomation does not apply to the
controls)
Stainless steel surfaces can be cleaned
using the Original Miele all purpose
microfibre cloth, or with a proprietary
non-abrasive cleaning agent designed
specifically for use on stainless steel.
To help prevent re-soiling, a
conditioning agent for stainless steel
can also be used. Follow the
manufacturer's instructions on the
packaging.
^ Wipe the surfaces dry using a soft
cloth.
19
Cleaning and care
Important for appliances with
lacquered housing
(special order finish)
It is very difficult to clean this type of
surface without causing minor marks to
the surface material. This can become
particularly noticeable with darker
colours and if there is halogen lighting
in the kitchen.
,An oversaturated filter is a fire
hazard.
If decor panels are fitted as an optional
extra, these need to be removed first.
Controls
The controls may suffer
discolouration or damage if soiling is
left on them for too long.
Remove soiling straight away.
Observe the General notes on cleaning
earlier in this section.
^ To do this, disengage them from their
catches.
^ See the notes under "Housing" for
how to clean the decor panels. Like
the grease filters, they can be
cleaned in the dishwasher.
Do not use stainless steel cleaning
agents on the controls.
Grease filters
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
rangehood.
To avoid a build-up of grease, the
grease filters should be cleaned
regularly (at least every 3-4 weeks), but
always clean immediately if the grease
filter indicator lamp comes on.
20
^ To take out the grease filters, release
the locking clip on the filter, lower the
filter 45°, unhook it at the back and
remove it.
To avoid damaging the filters or the
cooktop below, make sure you hold
the filters securely at all times when
handling them.
Cleaning and care
Cleaning the grease filters by hand
^ Clean the filters with a soft nylon
brush in a mild solution of hot water
and a small amount of washing-up
liquid.
Do not use undiluted washing up
liquid.
When removing the filters for cleaning,
also clean off any residues of oil or fat
from the now accessible housing to
prevent the risk of these catching fire.
When putting the grease filters back in
position, ensure that the locking clips
are facing down towards the cooktop.
Do not use:
– cleaning agents containing
descaling agents,
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
– oven sprays.
Cleaning the grease filters in the
dishwasher
^ Place the filters as upright as
possible in the lower basket. Ensure
the spray arm is not obstructed.
^ Do not wash at more than 65 °C. If a
Miele dishwasher is being used,
select the Sensor wash programme.
^ Use a mild dishwasher detergent.
Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.
If a grease filter is inadvertently
replaced upside down, insert a small
screwdriver blade into the slit to
disengage the clip.
^ After replacing the grease filters,
press the grease filter control for
approximately 3 seconds to reset the
operating hours counter.
The indicator lamp will go out.
If the grease filters are cleaned before
the operating hours counter has
reached its maximum, the grease filter
control should be pressed for
approximately 6 seconds to reset the
counter.
^ After cleaning, leave the filters to dry
on an absorbent surface before
replacing them.
21
Cleaning and care
Changing a halogen lamp
^ Before any cleaning or maintenance
work, disconnect the rangehood from
the mains supply. Ensure that:
– it is switched off at the isolator, or
– it is switched off at the wall socket
and the plug is withdrawn, or
– the mains fuse is disconnected, or
– the screw-out fuse is removed (in
countries where this is applicable).
,Exercise caution when changing
halogen lamps. They get very hot
during use and remain hot for some
time after being switched off. Let
them cool down before you change
them.
^ To access the halogen lamp, push
the lamp cover gently upwards. The
cover will open and can be pulled
down.
^ Pull the old halogen lamp out of the
connection socket.
^ Using a cloth or glove, push the new
lamp (12 V, 20 W, G4 cap) carefully
into the connection socket. Please
follow the manufacturer's instructions.
^ Push the cover back up and make
sure it clicks into place.
22
After sales service
In the event of a fault which you cannot
correct yourself, please contact:
– Miele
You will find the telephone number
and address of Miele on the back
cover of the manual.
Please quote the model and serial
number when contacting Miele. These
are shown on the data plate which is
visible when the grease filters are
removed.
Warranty
The warranty for this appliance is
2 years.
For further information, please refer to
your warranty booklet.
23
Appliance dimensions
DA 5320 W
The shaded areas 1) and 2) represent
the wall or ceiling area for the vent
cut-out, for feeding the connection
cable through to an external fan and for
fitting the connection socket.
Connection for air extraction
C 200 mm
24
Appliance dimensions
Safety distances between cooktop
and rangehood (S)
The minimum safety distances
between the top of a cooktop and
the bottom of the rangehood are
as follows, unless a greater
distance is specified by the
manufacturer of your cooking
appliance:
Cooking appliance
Distance
S
Electric cooktop
600 mm
Open electric grill
650 mm
Deep fat fryer (electric)
650 mm
Multi-burner gas cooktop
with maximum 45.4 MJ/h
total output, with no burner
having a greater output
than 16.2 MJ/h.
650 mm
Multi-burner gas cooktop
with total output greater
than 45.4 MJ/h, or a gas
cooktop including a single
burner with an output
greater than 16.2 MJ/h.
760 mm
Single gas cooktop with a
maximum output of
21.6 MJ/h
650 mm
Single gas cooktop with a
maximum output greater
than 21.6 MJ/h
760 mm
– Account should also be taken of the
height of the person who will be
using the rangehood most often. The
person should have sufficient space
to work comfortably at the cooktop,
and also be able to reach the
rangehood controls with ease.
– If positioned too high, extraction will
be inefficient.
– If you want the top of the rangehood
to be mounted flush with the ceiling,
make sure there is adequate space
below it for working. See
maximum/minimum appliance
height!
See "Warning and Safety"
instructions for further information.
25
Installation
Assembly parts
26
Installation
a 3 protective sheets
for use when fitting the tower.
b 2 hose clips
for securing the exhaust ducting.
c 1 reducing collar
for exhaust ducting C 150 mm.
d Telescopic wall bracket
for securing the rangehood to the
wall.
2 screws 3.9 x 7.5 mm
for securing the tower.
1 lever
for dismantling the tower.
Installation instructions
6 screws 5 x 60 mm and
6 plugs 8 x 50 mm for securing the
bracket to the wall.
,The screws and plugs are
designed for use in solid walls only.
For other types of wall construction,
alternative fixings will be required.
Make sure that the wall is able to
take the weight of the rangehood.
2 x M 6 self-tapping nuts
for securing the appliance.
27
Installation
Dismantling
Before installation, it is important to
read the information given on the
following pages as well as the
"Appliance dimensions" and the
"Warning and Safety instructions" at
the beginning of this book.
This is particularly crucial when
using the rangehood at the same
time as a heating appliance that
relies on air from the same room, as
this could result in the build-up of
toxic fumes.
Should the appliance ever need to be
dismantled, follow the installation
instructions in reverse order as
described on the installation sheet.
A lever is supplied to assist with the
removal of the tower.
Installation instructions
See enclosed Installation sheet for
instructions on how to install this
appliance.
Protective foil
(on stainless steel appliances)
The housing components have
protective foil around them to prevent
them being damaged during transport.
Please remove this foil before fitting the
housing components. It can be peeled
off easily.
28
^ After loosening the fixing screws on
the tower, push the lever between the
tower and the extension piece to
lever the tower out of its fixings.
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
Connection of this appliance should be
made via a suitable isolator which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
If the switch is not accessible after
installation, an additional means of
disconnection must be provided for all
poles.
For extra safety, it is advisable to install
a suitable residual current device
(RCD). Contact a qualified electrician
for advice.
Important
This appliance is supplied for
connection to an AC 230 V single
phase 50 Hz supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
Brown
= live
WARNING:
THIS APPLIANCE MUST BE
EARTHED
If the connection cable is damaged, it
must be replaced by the manufacturer
or similarly qualified persons to avoid a
hazard.
29
Operation with Control module DSM 400
The Miele DSM 400 Control module can
be used to combine the rangehood with
other components.
Installation
It enables the following:
Potential free connection
This is used for controlling another
appliance with the help of the
rangehood's On/Off button s.
If in any doubt, the advice of a
competent builder must be sought.
Connection to a light switch
The control module can be used to
switch on the rangehood lighting and
also to dim it, depending on model, via
a light switch in the house.
The tower needs to be removed before
the control module can be fitted to the
fan unit.
All electrical work must be carried
out by a competent, qualified
electrician.
30
Connection for air extraction
,Important: To avoid the danger
of toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the rangehood at the same time as
another heating appliance which
relies on air from the same room.
The rangehood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
If the exhaust ducting is secured to
the exhaust stub by a hose clip,
ensure that it is fitted correctly and
is not askew. Do not overtighten.
Otherwise the exhaust stub could
buckle and the non-return flap could
become jammed.
– When ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre to ensure no condensate
drains into the appliance.
– All ducting, pipework and fittings
must be of non-flammable materials.
– The exhaust ducting should be as
short and straight as possible.
– Only use rigid ducting fixed into
place.
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 200 mm.
If exhaust ducting with a diameter of
less than 200 mm, or if flat ducting is
used, the noise level of the
rangehood will increase and
extraction will be less efficient.
– Only reduce the diameter of the
ducting if absolutely necessary, e.g.
where narrower ducting has already
been installed.
– Only use wide radius bends. Tight
bends reduce the air throughput of
the rangehood.
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for extraction connection.
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
Important
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
31
Connection for air extraction
For exhaust ducting with a diameter of
200 mm, the following accessories are
required:
– Exhaust hose DAS 200
– Exhaust grille DFG 200, for mounting
on the external wall.
*Lead flashing
– Roof ducting DDF 200, for mounting
on a sloping tiled roof.
– Reducing collar for the exhaust stub
if using exhaust ducting with a 150
mm diameter.
32
Technical data
Total rated load
- DA 5320 W . . . . . . . . . . . . . . . . 600 W
Fan. . . . . . . . . . . . . . . . . . . . . . . . 500 W
Cooktop lighting
- DA 5320 W . . . . . . . . . . . . . . 5 x 20 W
Voltage . . . . . . . . . . . . . . . . . . . . 230 V
Frequency . . . . . . . . . . . . . . . . . . 50 Hz
AUS, NZ:
Plug rating . . . . . . . . . . . . . . . . . . . 10 A
Test marks . . . . . . . . . . Electrical safety
. . . . . . . . . . . . . . . . . . . . . . C-Tick Mark
Electrical cable length . . . . . . . . . 1.5 m
Fan performance
Extraction power according to
EN 61591
Extraction system C 200 mm:
Level I . . . . . . . . . . . . . . . . . . . 350 m3/h
Level II. . . . . . . . . . . . . . . . . . . 600 m3/h
Level III . . . . . . . . . . . . . . . . . . 850 m3/h
Level IV Intensive Setting . . . 1,300 m3/h
Extraction system C 150 mm:
Level I . . . . . . . . . . . . . . . . . . . 300 m3/h
Level II. . . . . . . . . . . . . . . . . . . 500 m3/h
Level III . . . . . . . . . . . . . . . . . . 700 m3/h
Level IV Intensive Setting . . . 1,000 m3/h
33
34
35
Alteration rights reserved / 3313
M.-Nr. 09 730 370 / 00