advertisement
Compartments, covers and trims
Center console, removing and installing
Assembly overview
1 - Instrument panel
2 - Center console
3 - Two screws
4 - Ashtray
5 - Screw
68-10
6 - Cigarette lighter
7 - Ashtray insert
8 - Boot
9 - Center console extension
10 - Two covers
11 - Two screws
12 - Mounting bracket
68-11
68-12
WARNING!
Disconnect battery ground strap before working on electrical system.
Removing
Notes:
The removal and installation procedures may have to be
modified slightly depending on equipment variants.
Obtain radio code before disconnecting battery.
It is not necessary to remove shifter trim plate on vehicles with
automatic transmission before removing center console.
- Unclip cover caps - 10 - and remove screws - 11 -.
- Unclip boot - 8 - and pull up.
- Pull out ashtray insert - 7 -.
- Remove screw - 5 -.
- Slide ashtray - 4 - forward, close and pull out -arrow- until it is possible to disconnect cigarette lighter - 6 - connector.
- Remove screws - 3 -.
- Pull center console - 2 - off upward over gear shift lever.
68-13
68-14
Installing
Install in reverse order of removal.
Notes:
Check operation of vehicle equipment (radio, clock, electric windows) as per Repair Manual/Owner's Manual after
reconnecting battery.
If engine Electronic Control Module (ECM) is subject to low voltage with ignition on, DTC memory and Readiness code must
be checked
Repair Manual, On Board Diagnostic (OBD) Fuel Injection &
Ignition, Repair Group 01
Center console extension, removing and installing
Assembly overview
1 - Center console
2 - Cover caps
3 - Two screws
4 - Center console extension
5 - Fuel flap switch
6 - Two screws
7 - Parking brake lever
68-15
WARNING!
Disconnect battery ground (GND) strap before working on electrical system.
Removing
Notes:
The removal and installation procedures may have to be
modified slightly depending on equipment variants.
Obtain radio code before disconnecting battery.
- Remove center armrest Page 68-29 .
- Remove rear ashtray Page 68-20 .
68-16
68-17
- Remove rear cup holder Page 68-23 .
- Pry off cover caps - 2 -.
- Remove screws - 3 -.
- Pull on parking brake lever - 7 -.
- Release center console extension - 4 - from center console - 1 -.
- Pull up front of center console extension -arrow A-, guide rear over center armrest support and pull connector off fuel flap switch
-5-.
- Pull center console extension - 4 - off forward over handbrake lever - 7 -.
68-18
Installing
Install in reverse order of removal.
Notes:
Check operation of vehicle equipment (radio, clock, electric windows) as per Repair Manual/Owner's Manual after
reconnecting battery.
If engine Electronic Control Module (ECM) is subject to low voltage with ignition on, DTC memory and readiness code must
be checked
Repair Manual, On Board Diagnostic (OBD) Fuel Injection &
Ignition, Repair Group 01
68-19
Front ashtray, removing
WARNING!
Disconnect battery ground strap before working on electrical system.
- Pull out ashtray insert -4-.
- Remove screw -2- from bracket -6-.
- Slide ashtray -5- forwards, close and pull out -arrow- until it is possible to disconnect cigarette lighter -3- connector.
- Pull ashtray -5- out from center console -1-.
Rear ashtray, removing
Assembly overview
1 - Center console extension
2 - Retaining lugs
3 - Storage compartment
Not with front armrest
4 - Storage compartment mat
Not with front armrest
5 - Ashtray insert
6 - Ashtray
7 - Cover caps
8 - Cup holder
9 - Locking hooks
In front of retaining lugs - 2 -
10 - Locking hooks
Behind retaining lugs - 2 -
11 - Locking lugs
68-20
Removing
- Remove cover caps - 7 -.
- Release ashtray - 6 - at left and right locking lugs - 11 - and remove.
68-21
Front cup holder, removing
- Fold up trim -1- for cup holder -2-.
- Press retaining clips -3 - on cup holder -2- using flat screwdriver and unclip.
- Pull out cup holder -2-.
68-22
Rear cup holder, removing and installing
Removing
- Remove rear ashtray Page 68-20 .
- Press down retaining hooks - 9 - and pull cup holder - 8 - out from center console - 1 -.
Installing
- Guide cup holder - 8 - into center console extension - 1 - until retaining hooks - 10 - meet retaining lugs - 2 -.
- Bend up retaining hooks - 9 - slightly.
- Install ashtray - 6 -.
68-23
Glove box, removing
- Release cover -1- with clips -2- from dash panel -3-.
- Pull out cover -1- -arrow-.
Note:
Screw -2- secures glove box -1- to carrier and is located behind center console.
- Remove center console Page 68-10 .
- Remove seven screws -arrows-.
- Remove glove box -1-.
68-24
68-25
Glovebox locking cylinder, removing and installing
- Tape off marked areas on flap -1- and -2- to protect against damage.
- Wrap jaws of waterpump pliers with tape -3- to avoid damaging glovebox/compartment.
68-26
Removing
- Stick ignition key -1- into locking cylinder -2- .
- Using pliers, push lock cylinder out of button -3- in direction of arrow.
Installing
- Press lock cylinder into button opening until you can hear it lock into place.
68-27
Armrest lid, removing
- Open armrest lid -1- approx. 60 degrees (see illustration).
- Hold armrest lid -1- firmly.
- Press armrest lid base -A- with right hand in direction of arrow (see figure) and with left hand move armrest lid top end -B- in direction of arrow (see figure) until lid has been released from armrest.
- Clean marks in armrest lid base -A- with clean flannel.
- Verify any existing damage to interior velour carpet, and substitute if necessary.
Installing
- Install in reverse order of removal.
Trim under steering column, removing
Note:
Remove left trim -2- first because screws -3- are
located under trim -2-.
- Remove two screws -1-.
- Unclip top of trim -2-.
- Remove two screws -3-.
- Unclip top of trim -4-.
68-28
Front center console, removing
- Unclip trim -3- from center console -1-.
- Remove bolt -2- (18 Nm or 13 ft lb) and remove center armrest.
68-29
Sun visor, removing
- Release sun visor -1- from mount -2-.
2000 (with sliding cover)
- Pry off cover cap -6-.
- Remove screw -5-.
- Release sun visor mount -4- from headliner and separate connector -3-.
- Pry off cover cap -7-.
- Remove screws -8- and remove mount -2-.
68-30
Center sun visor, removing
- Fold down center sun visor -1- -arrow-.
- Remove self-tapping screws -2- from roof frame -3- and take off sun visor.
68-31
Grab handle, removing
- Fold handle -1- down.
- Pry cover -2- up with screwdriver and fold open.
- Remove screws -3- and take off handle -1-.
68-32
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project