Eizo FlexScan L760T-C Touch Panel Color LCD Monitor User`s manual

User’s Manual
Touch Panel Color LCD Monitor
It shall be assured that the final system is in compliance
to IEC60601-1-1 requirements.
English
SAFETY SYMBOLS
This manual uses the safety symbols below. They denote critical information. Please read them
carefully.
WARNING
Failure to abide by the information in a WARNING may result in serious injury and
can be life threatening.
CAUTION
Failure to abide by the information in a CAUTION may result in moderate injury
and/or property or product damage.
Indicates a prohibited action.
Indicates to ground for safety.
x Power supplied equipment can emit electromagnetic waves, that could influence, limit or
result in malfunction of the monitor. Install the equipment in a controlled environment, where
such effects are avoided.
x This is a monitor intended for use in a medical setting.
Copyright© 2005 EIZO NANAO CORPORATION All rights reserved. No part of this manual
may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
electronic, mechanical, or otherwise, without the prior written permission of EIZO NANAO
CORPORATION.
EIZO NANAO CORPORATION is under no obligation to hold any submitted material or
information confidential unless prior arrangements are made pursuant to EIZO NANAO
CORPORATION's receipt of said information. Although every effort has been made to ensure
that this manual provides up-to-date information, please note that EIZO monitor specifications
are subject to change without notice.
VGA is a registered trademark of International Business Machines Corporation.
DPMS is a trademark and VESA is a registered trademark of Video Electronics Standards
Association.
Windows is a registered trademark of Microsoft Corporation.
ScreenManager, FlexScan and EIZO are registered trademarks of EIZO NANAO
CORPORATION in Japan and other countries.
2
English
TABLE OF CONTENTS
PRECAUTIONS ................................................................................... 4
1. INTRODUCTION ..................................................................................... 9
1-1. Features ........................................................................................................9
1-2. Package Contents..........................................................................................9
1-3. Controls & Connectors ..............................................................................10
2. CABLE CONNECTION ......................................................................... 12
2-1. Before connecting .......................................................................................12
2-2. Connecting the signal cable ........................................................................13
2-3. Touch Operation.........................................................................................15
2-4. Connecting two PCs to the monitor............................................................15
3. ScreenManager .................................................................................... 16
3-1. How to use the ScreenManager ..................................................................16
3-2. Adjustments and Settings ............................................................................17
3-3. Useful Functions .........................................................................................18
4. ADJUSTMENT ...................................................................................... 20
4-1. Screen Adjustment ......................................................................................20
4-2. Color Adjustment .......................................................................................23
5. ATTACHING A STAND.......................................................................... 25
6. TROUBLESHOOTING........................................................................... 27
7. CLEANING ............................................................................................ 31
8. SPECIFICATIONS ................................................................................. 32
9. GLOSSARY........................................................................................... 35
APPENDIX/ANHANG/ANNEXE .................................................................. i
TABLE OF CONTENTS
3
English
PRECAUTIONS
IMPORTANT!
x This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
x To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).
[Location of the Caution Statements]
[Symbols on the unit]
Symbol
4
PRECAUTIONS
Location
This symbol indicates
Front
Control panel
Power button
Press to turn the monitor’s power on or off.
Rear
Name Plate
Alternating current
Rear
Alerting electrical hazard
Rear
Caution
Refer to SAFETY SYMBOLS section in this
manual.
English
WARNING
If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.
Attempting to use a malfunctioning unit can be dangerous.
Do not dismantle the cabinet or modify the unit.
Dismantling the cabinet or modifying the unit may result in electric shock or
burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage.
If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Have the unit checked by a qualified service engineer before using it again.
Place the unit on a strong, stable surface.
A unit placed on an inadequate surface may fall, resulting in injury or
equipment damage.
When the unit is dropped, please ask your dealer for advice. Do not continue
using a damaged unit. Using a damaged unit may result in fire or electric
shock.
OK
Set the unit in an appropriate location.
Not doing so may cause damage and could result in fire or electric shock.
* Do not place outdoors.
* Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
* Do not place in a dusty or humid environment.
* Do not place in a location where the steam comes directly on the screen.
* Do not place near heat generating devices or a humidifier.
* Do not place in an inflammable gas environment.
PRECAUTIONS
5
English
WARNING
To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.
Use the enclosed power cord and connect to the standard power outlet
of your country. Be sure to remain within the rated voltage of the
power cord.
Not doing so may cause in fire or electric shock.
To disconnect the power cord, grasp the plug firmly and pull.
Never tug on the cord, doing so may cause damage and could result in fire or
electric shock.
The equipment must be connected to a grounded main outlet.
Not doing so may cause in fire or electric shock.
Use the correct voltage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may cause fire, electric
shock, or other damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
6
PRECAUTIONS
OK
English
WARNING
When attaching an arm stand, please refer to the user’s manual of the
arm stand and install the unit securely.
Not doing so may cause the unit to come unattached, which may result in
injury or equipment damage. When the unit is dropped, please ask your dealer
for advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock. When reattaching the tilt stand, please use the
same screws and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal which leaks from the panel is poisonous if it enters the eyes
or mouth.
If any part of the skin or body comes in direct contact with the panel, please
wash thoroughly. If some physical symptoms result, please consult your
doctor.
Follow local regulation or laws for safe disposal.
The backlight of the LCD panel contains mercury.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit
with the cord attached is dangerous. It may result in injury or equipment
damage.
When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
OK
Do not block the ventilation slots on the cabinet.
* Do not place books or any other papers on the ventilation slots.
* Do not install the unit in a closed space.
* Do not use the unit lying down or upside down.
Using the unit in these ways blocks the ventilation slots and prevents proper
airflow, leading to fire or other damage.
PRECAUTIONS
7
English
CAUTION
Do not touch the plug with wet hands.
Touching them may result in electric shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
Periodically clean the area around the plug.
Buildup of dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power switch
for the safety and the power conservation.
LCD Panel
In order to suppress the luminosity change by long-term use and to maintain
the stable luminosity, use of a monitor in lower brightness is recommended.
The screen may have defective pixels. These pixels may appear as slightly light
or dark area on the screen. This is due to the characteristics of the panel itself,
and not the product.
The backlight of the LCD panel has a fixed life span. When the screen becomes
dark or begins to flicker, please contact your dealer.
Do not scratch or press on the panel with any sharp objects, such as a pencil or
pen as this may result in damage to the panel. Do not attempt to brush with
tissues as this may scratch the panel.
8
PRECAUTIONS
English
1. INTRODUCTION
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
• Dual inputs compliant
• DVI (p.35) Digital input (TMDS (p.36)) compliant.
• Horizontal scanning frequency:
Vertical scanning frequency:
Resolution:
Analog input 30 - 81 kHz
Digital input 30 - 65 kHz
Analog input 49.5 - 75.5 Hz
Digital input 59 - 61 Hz (VGA text: 70 Hz)
1 M pixels (1280 dots x 1024 lines)
• Auto Adjustment compliant
• Support to sRGB (p.36) standard
• The height adjustable stand incorporated
• Touch Panel provided
• Touch Panel Pointer “TP1” is available (optional, p.14)
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
• LCD Monitor
• Power Cord
• Signal Cable (MD-C87)
• Touch Panel Cable (FD-C38)
• User’s Manual
• ScreenManager Quick Reference
• LIMITED WARRANTY
• CD-ROM for Touch Panel
(Contents: TouchWare (Touch Panel Driver), User’s Manual)
NOTE
• Please retain the packing materials for future transference.
• Regarding the installing the touch panel driver, please follow the instructions in the
CD-ROM.
1. INTRODUCTION
9
English
1-3. Controls & Connectors
Front
(1)
Control Panel
SIGNAL
1-2
MODE
AUTO
ENTER
(2) (3) (4) (5)
(1)ScreenManager®
(2)SIGNAL1-2
10
(6)
(7) (8)
Monitor Adjustment menu (p.16)
Input Signal
Selection Button
Switch the input signals when connecting 2
PCs. (p.15)
(3)MODE
Mode Button
Show or switch the color mode. (p.23)
(4)AUTO
Auto Adjustment
Button
Adjust the screen to appropriate condition
automatically. (analog input only)
(5)ENTER
Enter Button
Show the ScreenManager on the screen.
Confirm the setting / adjustment function.
Save the adjustment values.
(6)
Control Buttons
(Left, Down, Up,
Right)
Select the desired function.
Increase and decrease the adjustment value.
(7)
Power Switch
ON or OFF the monitor’s power.
(8)
Power Indicator
Indicate monitor’s operation status.
Blue: Operation
Flashing blue: Last 15 min. of operation
time before entering the power off state.
(p.18)
Flashing yellow slowly: Power off
1. INTRODUCTION
English
Rear
(13)
(14)
(15)
Bottom
(9)
(10) (11) (12)
(9)
Power Connector
Connect the power cord.
(10)
DVI-D Connector
(SIGNAL1)
Connect the optional digital cable.
(11)
D-Sub mini 15 pin
Connector
(SIGNAL2)
Connect the enclosed analog cable (MDC87)
(12)
RS-232C port
Connect the enclosed touch panel cable
(FD-C38).
(13) Hole for TP1
(14)
Hole for installing the lead of the TP1
(Optional Touch Panel Pointer).
Security Lock Slot
(15) Stand (Detachable)
Allows for connection of a security cable.
This lock supports Kensington’s MicroSaver
security system.
For further information, please consult:
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403
USA
Tel: 800-650-4242, x3348
Intl: 650-572-2700, x3348
Fax: 650-572-9675
http://www.kensington.com
The LCD monitor can be used with an other
stand by removing the stand (see page 25).
1. INTRODUCTION
11
English
2. CABLE CONNECTION
2-1. Before connecting
Before connecting your monitor to the PC, change the display screen settings (resolution
(p.35) and frequency) in accordance with the charts below.
NOTE
x The lower display modes like 640x 480, automatically enlarge to the maximum
display mode (1280 x 1024), and some lines of the characters may become fuzzy. In
this case, use <Smoothing> function (p.22) to make the lines clear.
x When your computer and display support VESA DDC, the suitable resolution and
the refresh rate are set by just plugging your display into the computer without any
manual settings.
Analog Input
Resolution
Frequency
320 ˜ 200
640 ˜ 480
720 ˜ 400
800 ˜ 600
1024 ˜ 768
1152 ˜ 864
1280 ˜ 960
1280 ˜ 1024
70 Hz
㨪75 Hz
70 Hz
Dot Clock
Remarks
135 MHz(Max)
VGA Mode13
VGA, VESA
VGA TEXT
VESA
VESA
VESA
VESA
VESA
㨪75 Hz
㨪75 Hz
75 Hz
60 Hz
㨪75 Hz
Digital Input
12
Resolution
Frequency
Dot Clock
Remarks
640 ˜ 480
720 ˜ 400
800 ˜ 600
1024 ˜ 768
1280 ˜ 1024
60 Hz
70 Hz
60 Hz
60 Hz
60 Hz
109 MHz
(Max)
VGA
VGA TEXT
VESA
VESA
VESA
2. CABLE CONNECTION
English
2-2. Connecting the signal cable
NOTE
x Be sure that the power switches of both the PC and the monitor are OFF.
1.
Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Digital Signal Input Connecter
3. Power Cord
Analog Signal Input Connecter
1. Signal Cable
2. Touch Panel Cable
Analog Input
Signal Cable
Signal Cable (enclosed, MDC87)
Connector of PC
Video Output
Connector/ D-Sub
mini 15 pin
Input Connecor
(monitor)/ D-Sub
mini 15 pin
PC
x Standard graphics card
Digital Input
Signal Cable
FD-C39 (Optional)
2.
Connector of PC
Video Output
Connector DVI-I
Input Connecor
(monitor)/ DVI
PC
x Digital Graphics card
Plug the enclosed touch panel cable (FD-C38) into the RS-232C port
of the monitor. Then, plug the other end of the cable into the COM
port of the PC.
2. CABLE CONNECTION
13
English
3.
Plug the power cord into the power connector on the rear of the
monitor. Then, plug the other end of the cord into a power outlet.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may cause in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may cause in fire or electric shock.
4.
Turn on the monitor’s main power and then switch on the PC's
power.
The monitor’s power indicator will light up (blue).
If an image does not appear, refer to the “6. TROUBLESHOOTING” (p.27) for
advice.
5.
Install the TouchWare with following the instructions on the CDROM.
Please carefully read the readme file of TouchWare at the installation.
NOTE
x When selecting the Calibration Type at the installing the TouchWare, select “2point calibration”.
14
2. CABLE CONNECTION
English
NOTE
x Whenever finished, turn off the PC and the monitor. Disconnecting the monitor
from the power supply is recommended to save energy completely.
x Adjust brightness of the screen depending on the brightness of your environment.
Too dark or too bright of a screen can cause eyestrain.
x Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
2-3. Touch Operation
Point and touch with one finger only.
NOTE
x Do not touch the screen while the computer is starting. Touch the screen after
disappearing TouchWare starting window.
x Do not touch the screen while turning on the monitor. Touch the screen one second
later after appearing the image.
x For the users with gloves, we recommend to use touch panel pointer, “TP1”
(optional). Regarding the installation, please refer to the User’s Manual of TP1.
2-4. Connecting two PCs to the monitor
Two PCs can be connected to the monitor through the DVI and the D-Sub mini 15 pin
connector on the back of the monitor.
Selecting the active input
The Input Signal Selection Button on the control panel can be used to select either Signal
1 or Signal 2 as the active input at any time. Every time the button is pressed, the input
changes. When switching the signal, the kind of the input signal (Signal1 or 2/Analog or
Digital) is displayed for a few seconds on the right top corner of the screen.
Input Signal Selection Button
SIGNAL
1-2
MODE
AUTO
ENTER
2. CABLE CONNECTION
15
English
3. ScreenManager
3-1. How to use the ScreenManager
ScreenManager
Main Menu
Control Buttons
Left, Down, Up, Right
SIGNAL
1-2
MODE
AUTO
Auto Adjustment Button
1.
ENTER
Enter Button
Entering the ScreenManager
Press the Enter Button once to display the main menu of the ScreenManager.
2.
Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control Buttons and press the Enter
Button. The sub menu appears.
(2) Use the Control Buttons to select the desired setting icon and press the Enter
Button. The setting menu appears.
(3) Use the Control Buttons to make all required adjustments and press the Enter
Button to save the settings.
3.
Exiting the ScreenManager
(1) To return to the main menu, select the <Return> icon or press the Down
Button twice, followed by the Enter Button.
(2) To exit the ScreenManager, select <Exit> icon or press the Down Button twice,
followed by the Enter Button.
NOTE
x Double clicking the Enter Button at any time also exits the ScreenManager menu.
16
3. ScreenManager
English
3-2. Adjustments and Settings
The following table shows all the ScreenManager’s adjustment and setting menus.
“*” indicates adjustments of analog input only.
Main menu
Screen
Sub menu
Reference
Clock
*
Phase
*
Position
*
Range Adjustment
*
4-1. Screen Adjustment (p.20)
Smoothing
Color
Brightness
4-2. Color Adjustment (p.23)
Color Mode
x Custom
Temperature
Gamma
Saturation
Hue
Gain
Reset
x sRGB
Others
*1
Input Signal
Set the input signal selection of
automatic or manual (p.19)
Off Timer
Set the power save (p.18)
VGA Selection
Select the display mode. (p.28)
Menu Position
Adjust the menu position.
Translucent
Set the transparency of the menu.
Menu Off Timer
Set the menu displaying time.
Reset
Return to the factory default settings.
(p.33)
Information
Information
Review the ScreenManager’s settings,
model name, serial number and usage
time*1.
Language
English, German,
French, Spanish,
Italian and Swedish
Select the ScreenManager’s language.
Due to the inspection on the factory, the usage time may not “0 hour” at shipping.
3. ScreenManager
17
English
3-3. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
x Auto Adjustment Button adjustments and settings in the
ScreenManager.
Unlocked function
x Adjustment of brightness by the Control Buttons.
x Input Signal Selection Button
x Mode Button
[To lock]
(1) Switch off the monitor’s power by the power switch on the control panel.
(2) Press on the Auto adjustment button while switching on the monitor’s power.
[To unlock]
(1) Switch off the monitor’s power by the power switch on the control panel.
(2) Hold down the Auto adjustment button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state after
a predetermined amount of time has lapsed. This function was created to reduce
afterimage characteristics that are particular to LCD monitors when the monitor screen
is left on for a long period without use.
[Procedure]
(1) Select <Off Timer> in the ScreenManager <Others> menu.
(2) Select “Enable” and press the Right and Left Buttons to adjust the “On Period” (1
to 23 hours).
[Off timer system]
PC
Monitor
On Period (1H - 23H)
Operation
Last 15 min. in “On period”
Advance Notice
“On period” expired
Power off
*1
*1
Blue Flashing
Flashing yellow slowly
Advance notice (Power Indicator flashing blue) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode, press
the power switch during the advance notice period. The monitor will continue to operate for
an additional 90 minutes.
[Power Resumption Procedure]
Press the power switch.
18
Power Indicator
Blue
3. ScreenManager
English
EIZO Logo display
Enables to display the EIZO logo for a while when switching on the monitor (Default is
no logo). If you desire to display or undisplay this logo, use this function.
[To display]
(1) Switch off the monitor’s power by the Power switch on the control panel.
(2) Hold down the Enter button once again and turn the power back on.
[To undisplay]
(1) Switch off the monitor’s power by the Power switch.
(2) Hold down the Enter button once again and turn the power back on.
Automatically selecting the input signal function
The monitor will automatically detect the inputted signal of either the connection for
display.
Connecting two PCs to the monitor
When the one computer is switched off, the monitor will automatically dislay the other
signal.
Use the ScreenManager to switch the input selection to manual.
[Procedure]
(1) Select <Input Signal> in the <Others> menu.
(2) Select “Manual”.
3. ScreenManager
19
English
4. ADJUSTMENT
The monitor displays the digital input image correctly based on its pre-setting
data. Adjust the brightness (p.23).
4-1. Screen Adjustment
Screen adjustments for the LCD monitor should be used in suppressing screen flickering
and also for adjusting the screen to its proper position. There is only one correct
position for each display mode. It is also recommended to use the ScreenManager
function when first installing the display or whenever changing the system.
Adjustment Procedure
NOTE
x Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments.
1.
Press the Auto Adjustment Button on the control panel.
The message “Your setting will be lost, if you press again now.” appears and
remains on the screen for 5 seconds. While the message is on the screen, press the
Auto Adjustment Button again to automatically adjust the clock, phase, and screen
position. If you do not wish to do adjust the screen, do not press the Auto
Adjustment Button again.
NOTE
x The Auto Adjustment function is intended for use on AT-compatible PC running
Windows. It may not work properly in either of the following cases.
When running an AT-compatible PC on MS-DOS (Not windows). The
background color for the “wall paper” or “desktop” pattern is set to black.
If the appropriate screen can not be made by using the Auto Adjustment
Button, adjust the screen through the following procedures. If the
appropriate screen can be made, proceed to step 4.
20
4. ADJUSTMENT
English
2.
We recommend setting the desktop pattern to that as shown in the
diagram below.
NOTE
x More precise adjustment is available for using the “Screen Adjustment
program” utility software. It can be downloaded from the EIZO homepage
(http://www.eizo.com/).
3.
Adjust by using <Screen> menu in the ScreenManager.
(1) Vertical bars appear on the screen
o
Use the <Clock> (p.35) adjustment.
Select the <Clock> and eliminate the vertical bars by using the Right and Left
of the Control Buttons.
Do not continuously press the Control Buttons, as the adjustment value will
change quickly and make it difficult to locate the most suitable adjustment
point. If the horizontal flickering, blur or bars appear, proceed to <Phase>
adjustment as follows.
(2) Horizontal bars appear on the screen.
o
Use the <Phase> (p.35) adjustment.
Select the <Phase> and eliminate the horizontal flickering, blurring or bars by
using the Right and Left Buttons.
NOTE
x Horizontal bars may not completely disappear from the screen depending on
the PC.
4. ADJUSTMENT
21
English
(3) The screen position is incorrect.
o
Use the <Position> adjustment.
The correct displayed position of the monitor is decided because the number
and the position of the pixels are fixed. The “Position” adjustment moves the
image to the correct position.
Select <Position> and adjust the position by using the Up, Down, Right and
Left Buttons.
If vertical bars of distortion appear after finishing the <Position> adjustment,
return to <Clock> adjustment and repeat the previously explained adjustment
procedure. Clocko Phaseo Position
4.
To adjust the output signal range (Dynamic Range) of the signal.
o
Use the <Range Adjustment> (p.36).
This controls the level of output signal range to display the whole color gradation
(256 colors).
[Procedure]
Press the Auto Adjustment Button on the control panel while displaying the
<Range Adjustment> menu to automatically adjust the range. The screen blanks
for a moment, and adjusts the color range to display the whole color gradation of
the current output signal.
5.
To smooth the blurred texts of the enlarged screen of the lower
resolutions.
o
Switch the <Smoothing> setting.
<Smoothing> is clear-cut the letters or lines.
Select <Smoothing> in the screen menu and select the suitable level from 1 ~ 5.
NOTE
x The “Smoothing” is disabled in the resolution 1280 x 1024.
x Since the displayed image is enlarged, the blurred texts may not be
necessarily lost completely.
22
4. ADJUSTMENT
English
4-2. Color Adjustment
In the analog input, perform the “Range Adjustment” (p.22) before making the
color adjustments.
The <Color> menu in the ScreenManager enables to change the color of the screen. By
using the <Color Mode>, the adjustment mode can be selected from <Custom mode> (to
adjust the color settings according to your preference) and <sRGB> mode.
NOTE
x Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments. (Allow the monitor to warm up for at least 20 minutes before making
adjustments.)
x Performing the <Reset> of the <Color> menu returns the color settings to the
default settings.
x The values shown in percentages represent the current level within the specific
adjustment. They are available only as a reference tool. (To create an uniform white
or black screen, the percentages for each will probably not be the same.)
x Direct pressing the Mode Button on the control panel also can show or switch the
Color Mode.
Adjustment Contents
Menu
Brightness
Color Mode
Custom
sRGB
—
—
Function Descriptions
To set the brightness of the
screen
Adjustable range
0 a 100%
NOTE
x Direct pressing the up and down control button also
can adjust the brightness. After the adjustment, press
Enter button to save the data.
Temperature
(p.35)
—
-
To set the color temperature
4,000 a 10,000 K
in 500 K increments
(including 9,300 K).
Default setting is off
(normal white)
NOTE
x The values shown in the Kelvin are available only as a
reference tool.
x Setting the temperature under 4,000 K or over 10,000
K invalidates the color temperature setting. (The color
temperature’s setting turns “OFF”.)
4. ADJUSTMENT
23
English
Menu
Gamma
(p.35)
Color Mode
Custo
sRGB
m
—
-
Function Descriptions
To set the gamma value
Adjustable range
1.8 a 2.6
NOTE
x If setting the gamma value, the using the monitor in
the digital signal input is recommended.
If using the monitor in the analog input signal, set the
gamma value from 1.8 to 2.2.
Saturation
—
-
To change the saturation
-128 a 127
Setting the minimum
level (-128) turns the
image to the
monochrome.
NOTE
x The <Saturation> adjustment may cause
undisplayable color tone.
Hue
—
-
To change the flesh color,
etc.
-32 a 32
NOTE
x The <Hue> adjustment may cause undisplayable color
tone.
Gain (p.35)
—
-
To change each color (red,
green and blue)
0 a 100%
By adjusting the red,
green and blue color
tones for each mode,
custom colors can be
defined. Display a
white or gray
background image and
adjust the <Gain>.
NOTE
x The values shown in the percentage are available only
as a reference tool.
x Setting the <Temperature> (p.35) invalidates the
<Gain> adjustment. <Gain> setting returns to the
default.
Reset
24
4. ADJUSTMENT
—
-
To return the color settings
to the default settings
Select the “Reset”.
English
5. ATTACHING A STAND
The LCD monitor can be used with other stand by removing the tilt stand and attaching
the stand to the LCD monitor.
NOTE
x If you will use the other stand, confirm the followings to the manufacturers before
selecting.
- Hole spacing on the stand mounting: 100 mm x 100 mm (VESA compliant)
- Supportable Weight: Total weight of the monitor (without stand) and attaching
equipment such as a cable
- TÜV/GS approved stand
x Please connect cables after attaching a stand.
Setup Procedure
1.
Hold the center of the stand mounting cover and slide them
rightward or leftward to remove the mounting cover.
Stand mounting cover
2.
Lay the LCD monitor down. Do not scratch the panel.
3.
Remove the tilt stand by loosening the 4 screws.
5. ATTACHING A STAND
25
English
4.
Attach a stand to the LCD monitor securely with the same screws.
stand
4 Mounting Screws: M4 x 12 mm
26
5. ATTACHING A STAND
English
6. TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO dealer. The
latest FAQ information is supplied on EIZO homepage (http://www.eizo.com/).
x
No Picture Problems
Problems
1. No picture
x Indicator status: Off
x Indicator status: Blue
x Indicator status: Yellow Flashing
2. Following messages appear.
(Error messages shown below will
remain on the screen for 40
seconds.)
x Whenever an error signal message
appears, the signal frequency will be
displayed in red.
Points to check with possible solutions
†
Check that the power cord is correctly
connected. If the problem persists, turn off the
monitor power for a few minutes, then turn it
back on and try again.
†
Check the “Brightness” setting.
†
Switch the signal input by pressing the Input
Signal Selection Button on the front control
panel.
†
Try pressing the power switch.
These message appear when the signal is not
inputted correctly, even if the monitor functions
properly.
†
When the image is displayed correctly after a
short time, there is no problem with the
monitor. (Some PCs do not output the signal
soon after powering on.)
†
Check that the PC is turned ON.
†
Check that the signal cable is properly
connected to the PC or graphics board.
†
Switch the signal input by pressing the Input
Signal Selection Button on the front control
panel.
†
Use the graphics board’s utility software to
change the frequency setting. (Refer to the
manual of the graphics board.)
6. TROUBLESHOOTING
27
English
Imaging problems
x
Problems
Points to check with possible solutions
3. Display position is incorrect.
†
Adjust the image position using the <Position>
(p.22)
†
The two display modes, VGA 720 x 400 (70
Hz) and 320 x 200 (70 Hz), have the same
signal timings. Using this adjustment selects the
appropriate display mode. (This function effects
only when the resolution is VGA 720 x 400 (70
Hz) or 320 x 200 (70 Hz).
†
If the problem persists, use the graphics board’s
utility software to change the display position if
available.
4. Vertical bars of distortion appear.
†
Decrease the vertical bars using the <Clock>.
(p.21)
5. Horizontal bars of distortion
appear.
†
Decrease the horizontal bars using the <Phase>.
(p.21)
6. Letters and lines appear blurred.
†
Switch the <Smoothing> mode. (p.22)
7. The screen is too bright or too
dark.
†
Adjust the <Contrast and brightness> (The
baklight of the LCD monitor has a fixed life
span. When the screen becomes dark or begins
to flicker, please consult your dealer.)
8. Afterimages appear.
†
When the screen image is changed after
displaying the same image for a long period, an
afterimage may appear. The “Afterimage” can
be removed gradually by changing the displayed
image. Use the “Off Timer” function and avoid
keeping the screen on all the time.(p.18)
9. The screen has defective pixels
(e.g. slightly light or dark).
†
This is due to the characteristics of the panel
itself, and not the LCD product.
28
6. TROUBLESHOOTING
English
x
Other problems
Problems
Points to check with possible solutions
10.The <Smoothing> cannot be
selected.
†
<Smoothing> is disabled when the screen is
displayed in the 1280 x 1024.
11.The Enter Button does not
operate.
†
The adjustment lock is probably on. To unlock:
switch the LCD monitor off. Then, while
pressing the Auto Adjustment Button switch,
the power on. (p.18)
The adjustment lock is probably on. To unlock:
12.The Auto Adjustment Button does †
switch the LCD monitor off. Then, while
not operate.
pressing the Auto Adjustment Button switch,
the power on. (p.18)
†
The Auto adjustment function is intended for
use on the AT-compatible PC running Windows.
It may not work properly in either of the
following cases.
x When running an AT-compatible PC on MSDOS (Not windows).
x The background color for the “wall paper”
or “desktop” pattern is set to black.
†
Some signals from a graphics board may not
function properly.
x
Touch Panel Problems
Problems
Points to check with possible solutions
13.Cursor is jittery. / Drawing lines
are not straight and smooth.
†
The influence of metal may cause jittery cursor.
†
Using the monitor with dual-monitor system
may cause jittery cursor.
†
Run the Stabilize Cursor option from the
TouchWare.
†
Check the baud rate for the touch panel on
14.Continuous touch sound./
TouchWare. The baud rate of 1200 bps may
Much time requirement for
executing touch screen
cause continuous touch sound or much time
calibration or cursor stabilization.
requirement for executing touch screen
calibration or cursor stabilization.
6. TROUBLESHOOTING
29
English
Problems
15.Cursor position is not correct. /
Cursor jumps.
Points to check with possible solutions
†
When cursor position is incorrect or cursor
jumps, turn off and on the monitor.
x The drawing touch (touch operation with
dragging the finger on the touch panel) to
draw the picture may cause incorrect cursor
position.
x Changing the position or angle of the
monitor while the monitor operation will
cause cursor jump.
x Keep metals away from the panel surface.
x Point and touch with one finger only. Keep
other fingers away from the touch screen.
Do not rest the hand in the monitor or bezel
while touching the screen.
x Do not touch the screen while the computer
is starting. Touch the screen after
disappearing TouchWare starting window.
x Do not touch the screen while turning on the
monitor. Touch the screen one second later
after appearing the image.
x The spray for preventing static electricity
may influences the sensibility of the touch
panel. Do not use it on cleaning.
30
6. TROUBLESHOOTING
English
7. CLEANING
Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.
NOTE
x Never use thinner, benzene, ethanol, abrasive cleaners, or other strong solvents, as
these may cause damage to the cabinet or panel.
x Never use spray for preventing static electricity, as it may influence the sensibility of
the touch panel.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to the
manual of the PC.)
Panel
x The Panel surface can be cleaned with a soft cloth, such as cotton or lens paper.
x If necessary, stubborn stains can be removed by moistening part of a cloth with water
or isopropyl alcohl to enhance its cleaning power.
7. CLEANING
31
English
8. SPECIFICATIONS
LCD Panel
48 cm (19.0 inch), TFT color LCD panel with Anti-Glare Hard
Coating, Viewing Angle: H: 178°, V: 178° (CR≥10)
Dot Pitch
0.294 mm
Horizontal Scan Frequency
Analog: 30 ~ 81 kHz (Automatic)
Digital: 30 ~ 65 kHz
Vertical Scan Frequency
Analog: 49.5 ~ 75.5 Hz (Automatic)
Digital: 59 ~ 61 Hz, (VGA Text : 70Hz)
Resolution
1 M pixels (1280 dots x 1024 lines)
Dot Clock (Max.)
Analog: 135 MHz
Digital: 109 MHz
Display Colors
16 million colors (max.)
Display Area
376.3 mm (H) ×301.0 mm (V) (13.7” (H) x 11.0” (V))
(Viewable image size: 481 mm (18.9”))
Touch Panel
OS
Microsoft Windows 2000/XP
(Not compatible with MacOS)
Communication RS-232C serial
protocol
Detective
Analog capacitive technology, finger touch
method
Power Supply
100-120/200-240 VAC±10%, 50/60 Hz,
0.65-0.55 A/0.4-0.35 A
Power Consumption
Max.: 40 W
Input Connector
D-Sub mini 15 pin, DVI-D
Analog Input Signal (Sync)
Separate, TTL, Positive/Negative
Analog Input Signal (Video)
0.7Vp-p/75Ω Positive
Input Signal (Digital)
TMDS (Single Link)
Signal registration
Analog: 45 (Factory preset: 22)
Plug & Play
VESA DDC 2B
Dimensions
with stand
414 mm (W) x 442.5 ~524.5mm(H) x 208.5 mm (D)
(16.3”(W) x 17.4” ~ 20.6”(H) x 8.2”(D))
without stand
414 mm (W) x 340 mm (H) x 64 mm (D)
(16.3”(W) x 13.4”(H) x 2.52” (D))
Weight
with stand
9.0 kg (19.8 lbs.)
without stand
6.0 kg (13.2 lbs.)
Environment
Temperature
Operating: 0 °C ~ 35 °C (32 °F ~ 95 ° F)
conditions
Storage: -20 °C ~ 60 °C (-4 °F ~ 140 ° F)
Humidity
30% to 80% R.H. Non-condensing
Pressure
860 to 1,060 hPa
Certifications and Standards
100-120 VAC
CB, NRTL/C-TÜV, FCC-B
200-240 VAC
CE(93/42/EEC), CB, TÜV Rheinland/GM
Classification of Equipment
Type of protection against electric shock: Class I
EMC class: EN60601-1-2 2001: Group1 Class B
Classification of medical device (MDD 93/42/EEC): Class I
32
8. SPECIFICATIONS
English
Default settings
Brightness
100%
Smoothing
3
Temperature
Off (normal white: approx. 6500 K)
Input Signal
Auto
Off Timer
Disable
Language
English
Optional
Touch Panel Pointer
Dimensions
TP1
Unit mm (inches)
8. SPECIFICATIONS
33
English
Pin Assignment
D-Sub mini 15 pin connector
3
4
5
15
1
2
8
9
10
7
6
14 13 12 11
Pin
No.
1
2
3
4
5
Signal
Red video
Green video
Blue video
Ground
No pin
Pin
No.
6
7
8
9
10
Signal
Red ground
Green ground
Blue ground
No pin
Ground Shorted
Pin
No.
11
12
13
14
15
Signal
Ground Shorted
Data (SDA)
H. Sync
V. Sync
Clock (SCL)
DVI-D Connector
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
Pin
No.
1
2
3
4
5
6
7
8
Signal
TMDS Data2TMDS Data2+
TMDS Data2/4
Shield
NC*
NC
DDC Clock (SCL)
DDC Data (SDA)
Analog Vertical
Sync
Pin
No.
9
10
11
12
13
14
15
16
Signal
TMDS Data1TMDS Data1+
TMDS Data1/3
Shield
NC
NC
+5V Power
Ground (For +5V)
Hot Plug Detect
Pin
No.
17
18
19
20
21
22
23
24
Signal
TMDS Data0TMDS Data0+
TMDS Data0/5
Shield
NC
NC
TMDS Clock shield
TMDS Clock+
TMDS Clock(*NC: No Connection)
RS-232C Port (Mini DIN 6 pin)
5
6
3
4
2
34
1
8. SPECIFICATIONS
Pin No.
1
2
3
4
5
6
Signal
RXD
RTS
CTS
GND
TXD
GND
English
9. GLOSSARY
Clock
With the analog input signal display, the analog signal is converted to a digital signal
by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to
produce the same number clock pulse as the dot clock of the graphics system. When
the clock pulse is not correctly set, some vertical bars of distortion are displayed on
the screen.
Color Temperature (Temperature)
Color Temperature is a method to measure the white color tone, generally indicated
in degrees Kelvin. At high temperatures the white tone appears somewhat blue, while
at lower temperatures it appears somewhat red. Computer monitors generally give
best performance at high temperature settings.
5,000 K: Slightly reddish white.
6,500 K: Warm-white tone, similar to white paper or daylight.
9,300 K: Slightly bluish white.
DVI
(Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly
without loss with the signal transition method “TMDS”.
There are two kinds of DVI connectors. One is DVI-D connector for digital signal
input only. The other is DVI-I connector for both digital and analog signal inputs.
Gain Adjustment
Adjusts each color parameter for red, green and blue. The color of the LCD monitor
is displayed through the color filter of the LCD panel. Red, green and blue are the
three primary colors. The colors on the monitor are displayed by combining these
three colors. The color tone can change by adjusting the illumination amount passed
through each color’s filter.
Gamma
Generally, the relationship that the light intensity values of a monitor change
nonlinearly to the input signal level is called “Gamma Characteristic”. On the
monitor, low gamma values display the whitish images and high gamma values
display the high contrast images.
Phase
The phase adjustment decides the sampling timing point for converting the analog
input signal to a digital signal. Adjusting the phase after the clock adjustment will
produce a clear screen.
9. GLOSSARY
35
English
Range Adjustment
The Range Adjustment controls the level of output signal range to display the whole
color gradation.
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated to
form the screen image. The EIZO L760T-C display panel consists of 1280 horizontal
pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are
displayed as a full screen.
sRGB (Standard RGB)
“International Standard for Red, Green, and Blue color space”
A color space was defined with the aim of the color matching between applications
and hardware devices, such as monitors, scanners, printers and digital cameras. As a
standard default space, sRGB allows Internet users to closely match colors.
TMDS
(Transition Minimized Differential Signaling)
A signal transition method for the digital interface.
36
9. GLOSSARY
APPENDIX/ANHANG/ANNEXE
Preset Timing Chart for Analog input
Timing-Übersichten für Analog Eingang
Synchronisation des Signaux pour Analog numerique
Based on the signal diagram shown below 16 factory presets have been registered in the
monitor's microprocessor.
Der integrierte Mikroprozessor des Monitors unterstützt 16 werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
16 signaux ont été enregistrés en usine dans le microprocesseur du moniteur,
conformément au diagramme de synchronisation ci-dessous.
Mode
i
Dot Clock
MHz
Sync Polarity
H
V
Frequencies
H kHz
V Hz
VGA Mode13
320 × 200
25.2
Nega.
Nega.
31.47
59.94
VGA
640 × 480
25.2
Nega.
Nega.
31.47
59.94
VGA
720 × 400
28.3
Nega.
Posi.
31.47
70.09
VESA
640 × 480
31.5
Nega.
Nega.
37.86
72.81
VESA
640 × 480
31.5
Nega.
Nega.
37.50
75.00
VESA
800 × 600
36.0
Posi.
Posi.
35.16
56.25
VESA
800 × 600
40.0
Posi.
Posi.
37.88
60.32
VESA
800 × 600
50.0
Posi.
Posi.
48.08
72.19
VESA
800 × 600
49.5
Posi.
Posi.
46.88
75.00
VESA
1024 × 768
65.0
Nega.
Nega.
48.36
60.00
VESA
1024 × 768
75.0
Nega.
Nega.
56.48
70.07
VESA
1024 × 768
78.8
Posi.
Posi.
60.02
75.03
VESA
1152˜864
108.0
Posi.
Posi.
67.50
75.00
VESA
1280˜960
108.0
Posi.
Posi.
60.00
60.00
VESA
1280˜1024
108.0
Posi.
Posi.
63.98
60.02
VESA
1280˜1024
135.0
Posi.
Posi.
79.98
75.03
APPENDIX/ANHANG/ANNEXE
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: FlexScan L760T-C
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable
- Stereo mini-jack cable
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Hinweise zur Auswahl des richtigen Schwenkarms für Ihren Monitor
Dieser Monitor ist für Bildschirmarbeitsplätze vorgesehen. Wenn nicht der zum
Standardzubehör gehörige Schwenkarm verwendet wird, muss statt dessen ein geeigneter
anderer Schwenkarm installiert werden. Bei der Auswahl des Schwenkarms sind die
nachstehenden Hinweise zu berücksichtigen:
Der Standfuß muß den nachfolgenden Anforderungen entsprechen:
a) Der Standfuß muß eine ausreichende mechanische Stabilität zur Aufnahme des Gewichtes
vom Bildschirmgerät und des spezifizierten Zubehörs besitzen. Das Gewicht des
Bildschirmgerätes und des Zubehörs sind in der zugehörenden Bedienungsanleitung
angegeben.
b) Die Befestigung des Standfusses muß derart erfolgen, daß die oberste Zeile der
Bildschirmanzeige nicht höher als die Augenhöhe eines Benutzers in sitzender Position ist.
c) Im Fall eines stehenden Benutzers muß die Befestigung des Bildschirmgerätes derart
erfolgen, daß die Höhe der Bildschirmmitte über dem Boden zwischen 135 – 150 cm
beträgt.
d) Der Standfuß muß die Möglichkeit zur Neigung des Bildschirmgerätes besitzen (max.
vorwärts: 5°, min. nach hinten t 5°).
e) Der Standfuß muß die Möglichkeit zur Drehung des Bildschirmgerätes besitzen (max. ±
180°). Der maximale Kraftaufwand dafür muß weniger als 100 N betragen.
f) Der Standfuß muß in der Stellung verharren, in die er manuell bewegt wurde.
g) Der Glanzgrad des Standfusses muß weniger als 20 Glanzeinheiten betragen (seidenmatt).
h) Der Standfuß mit Bildschirmgerät muß bei einer Neigung von bis zu 10° aus der
normalen aufrechten Position kippsicher sein.
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland
zusammen mit dem Partner eds-r gmbh rücknahmesysteme. Dort werden die Geräte in ihre
Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden. Um einen Abholtermin
zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende Rufnummer:
02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-Adresse:
www.eizo.de.
Recycling Information for customers in Switzerland:
All recycling information is placed in the SWICO’s website.
http://www.swico.ch
Recycling-Information für Kunden in der Schweiz:
Alle Informationen zum Thema Recycling finden Sie auf der Homepage des Brancheverbandes
SWICO.
http://www.swico.ch
Renseignements de recyclage pour les clients en Suisse:
Vous trouvez tous les renseignements pour le sujet de recyclage sur la page WEB de I’UNION
DE BRAN CHE SWICO.
http://www.swico.ch
Recycling Information for customers in USA:
All recycling information is placed in the EIZO Nanao Technologies, Inc’s website.
http://www.eizo.com/contact/index.html
Återvinnings information för kunder i Sverige:
All information om återvinning finns på Eizo Europe AB:s hemsida:
www.eizo.se